高压清洗机说明书
高压清洗机使用说明书及故障排除法和简单的维修处理
成都力锋产品使用说明书一、使用说明1、开机前的准备：a、开机前检查进水管过滤器安装正确。
b、开机前必须检查箱体机油到油窗一半。
c、开机前安装进水管，注意：进水管必须可靠连接（垫上進水管橡膠墊Φ26*Φ14）。
2、新机第一次使用时，可将过滤器先不装，将接过滤器一端与自来水管道连接，打开自来水阀门，按动清洗机主开关，使电机工作，待出水管出水量大于未开机状态时，再工作5秒左右，停机。
将工厂原配的过滤器可靠地连接后放入储水罐底部。
使用储水罐时，必须加注清洁的水源3、出水管连接：把高压胶管的接头与增压泵出水管口上的接头相连；另一头与水枪上的接头相连。
4、喷头选择本机所用的喷头一定要使用原厂提供的配套喷头5、清洗作业时，喷头与被清洗面得距离不宜太远，一般不超过10公分。
因喷头的冲击力是随喷射距离的增大而减小。
6、正常状态下，清洗压力不超过额定工作压力为宜，若有特殊需要时，也可将机器压力升到最高压力，但不建议机器在最高压力下长期运转。
7、清洗结束松开扳机关闭水枪后，本机器会自动关停电机。
若较长时间不使用机器，建议关闭电源开关，打开水枪扳机释放内部压力。
使用完毕，必须将水枪内压力完全释放8、使用时，泵体的泄水孔有水滴出，并不影响使用，属正常运行。
9、该机长时间闲置后使用：由于单相电机起动力矩较小，如按下起动开关，电机发出嗡嗡声（电机并不远转），应立即按停机按钮，反复二，三次，电机即能运转；如果电机仍然不能起动，请拆去电机风扇罩壳，用手转动风叶二，三周后，再启动电机。
并在停机状况下重新装好风扇罩壳。
二、保养1.每100小时更换一次机油，建议使用CD15W-40机油，正确使用机油对保证机器使用寿命非常重要。
2、如遇寒冷天气有结冰时或长期不用时，应将机内剩水排尽，方法是将进水管离开供水系统，开机脱水远转1分钟左右。
同时拆下进水管与出水管以排尽管中剩水。
高压清洗机内部积水结冰后会引起电机堵转，造成电机烧机等严重后果。
三、安全用电注意事项1、项目之安全检查a、经常检查电动机引接线是否牢固可靠完好无损。
高压清洗机的使用说明
移动部件的伤害
移动部件能够夹住、刺入手指或身体的其他部位。 1.保证移动部件的清洁。 2.不要操作设备，当保护装置，或盖子去掉以后。 3.带压的设备会没有警示启动。在检查、移动、遵守压力释放程序，断开电源或气 源
有毒液体或烟气伤害
如果有毒的液体或烟气落入眼睛或皮肤上，吸入或吞咽，能够引起严重的伤害或死亡。 1.阅读你所使用液体的MSDS 来了解其特殊的危害。 2.在合格的箱子内存放有害液体，按照适合的操作指南处理液体。 3.喷射 或清洁设备时，一定要戴不透水的手套。
活塞和吸入的止回阀，排泄泵 247599在场家设定，用于低粘度 的液体，这样的设定对泵有最小的 冲击，调整这个阀用于高粘度的液 体。见操作手册 总是在液体被泵到底部前停泵如果 液体泵干喉部密封会损坏，完成泵 作业后放压。 如果你正在泵送的液体，干的，凝 固，快速凝结，尽可能多次用合适 的溶剂冲洗系统，避免在泵里或管 理形成干液 每操作40小时检查，密封螺母， 放压后拧紧螺母。拧的要合适，过 紧会引起密封损毁。
空气和液体管线：使用导电的管子。 空压机：按照制造商的建议。 喷枪和分配阀：通过连接接地的液体 管线和泵。 液体的供应容器：参考当地的标准。 被喷物体：参考当地的标准。 当冲洗溶剂桶时：参考当地的标准。 使用导电的金属桶，放在地上不要放 在不导电的地方，像纸或硬纸板上， 阻断接地。 当冲洗或泄压时保证接地持续：使喷 枪的金属部分和泄压阀紧靠在金属桶 边，然后开启枪和阀。
高压清洗机成套设备适用于压力清洗，只适合水和干净的溶 液
重要的安全介绍 看这本操作手册中所有的警告和介绍和你个自清洗机的操作说明并保存好
。
有关的操作手册
火灾和爆炸的危害
高压水射流清洗机安全使用指南说明书
高压水射流清洗机安全使用指南说明书在使用高压水射流清洗机进行清洗作业前，请务必仔细阅读本指南，并严格按照以下操作步骤进行操作。
高压水射流清洗机虽然具有高效清洁能力，但在不正确操作的情况下，也可能带来严重的安全风险。
以下是使用高压水射流清洗机的安全指南：1. 安装准备：在安装高压水射流清洗机前，请确保已经切断电源，并确认机器是处于关闭状态。
按照使用说明书中的指引，正确地安装和连接机器，并检查所有配件是否牢固。
2. 保证工作区域安全：在进行清洗作业前，请确保工作区域没有人员、动物或其他干扰物。
清洗机的操作区域应该牢固、平稳，并有足够的空间来操作机器。
3. 佩戴个人防护装备：为了保障您的安全，请佩戴适当的个人防护装备，包括护目镜、手套、耳塞以及防滑鞋等。
这些装备能够帮助您降低受伤的风险。
4. 电源和电缆安全：在使用高压水射流清洗机前，请确保电源线路和插头完好无损。
不要将电缆拖在地上以防止绊倒。
同时，防止电缆接触水或其他液体，以避免触电危险。
5. 水源和压力控制：在连接水源之前，请确保水源的质量和压力适中。
如果水源压力过高，请安装压力调节器来降低压力。
确保高压水射流清洗机在允许的压力范围内操作。
6. 操作前的检查：在启动高压水射流清洗机之前，请检查所有操作按钮、开关和阀门的功能。
确保它们没有堵塞或损坏，并且可以正常工作。
7. 喷嘴和喷嘴附件使用：在使用喷嘴之前，请确保喷嘴及其附件完好无损。
使用合适的喷嘴和附件可以提高清洗效果，并确保喷嘴的稳定性。
在更换或清洁喷嘴时，请务必将机器关闭并切断电源。
8. 操作注意事项：- 操作时保持稳定的姿势，避免突然移动或转向，以防止摔倒或滑倒。
- 不要将高压水射流对准人体或其他易受损物品，以免造成伤害或损坏。
- 避免高压水射流直接接触电线、插座、电气设备或其他容易导电的物体，以减少触电风险。
- 不要将手指或其他物体放入喷嘴或其它机器的旋转零部件中。
- 在机器运行期间，不要随意停止或解除喷射压力，以免造成突然高压释放，引起意外事故。
高压清洗机使用说明书及故障排除法和简单的维修处理精编版
高压清洗机使用说明书及故障排除法和简单的维修处理公司标准化编码 [QQX96QT-XQQB89Q8-NQQJ6Q8-MQM9N]成都力锋产品使用说明书一、使用说明1、开机前的准备：a、开机前检查进水管过滤器安装正确。
b、开机前必须检查箱体机油到油窗一半。
c、开机前安装进水管，注意：进水管必须可靠连接（垫上进水管橡胶垫Φ26*Φ14）。
2、新机第一次使用时，可将过滤器先不装，将接过滤器一端与自来水管道连接，打开自来水阀门，按动清洗机主开关，使电机工作，待出水管出水量大于未开机状态时，再工作5秒左右，停机。
将工厂原配的过滤器可靠地连接后放入储水罐底部。
使用储水罐时，必须加注清洁的水源3、出水管连接：把高压胶管的接头与增压泵出水管口上的接头相连；另一头与水枪上的接头相连。
4、喷头选择?本机所用的喷头一定要使用原厂提供的配套喷头5、清洗作业时，喷头与被清洗面得距离不宜太远，一般不超过10公分。
因喷头的冲击力是随喷射距离的增大而减小。
6、正常状态下，清洗压力不超过额定工作压力为宜，若有特殊需要时，也可将机器压力升到最高压力，但不建议机器在最高压力下长期运转。
7、清洗结束松开扳机关闭水枪后，本机器会自动关停电机。
若较长时间不使用机器，建议关闭电源开关，打开水枪扳机释放内部压力。
使用完毕，必须将水枪内压力完全释放?8、使用时，泵体的泄水孔有水滴出，并不影响使用，属正常运行。
9、该机长时间闲置后使用：由于单相电机起动力矩较小，如按下起动开关，电机发出嗡嗡声（电机并不远转），应立即按停机按钮，反复二，三次，电机即能运转；如果电机仍然不能起动，请拆去电机风扇罩壳，用手转动风叶二，三周后，再启动电机。
并在停机状况下重新装好风扇罩壳。
二、保养1.每100小时更换一次机油，建议使用CD15W-40机油，正确使用机油对保证机器使用寿命非常重要。
2、如遇寒冷天气有结冰时或长期不用时，应将机内剩水排尽，方法是将进水管离开供水系统，开机脱水远转1分钟左右。
高压清洗机说明手册
高压清洗机说明书型号:TVE070C、TVF070CTVB080G、TVD100CTVG100C自行用时存放在室内。
本机供应电流应不少于额定电流。
使用前，请先检查延长电线，如果已损坏，请更换。
使用不适合的外延电线会有很大的危险。
不要滥用延长电线，拔插头时请不要猛拉电线。
延长电线远离热源及锋利刀口。
分离本机时，请先将插头从插座处分离。
警告：如果供给电线已损坏，必须使用专用的电线，也可让销售商或生产厂家重新装配。
警告：为了减少触电风险，在下雨和雷雨天气不要开启和操作本机。
保持所有接口干燥，并脱离地面，不要用湿手触摸插头，严禁水渗透本机。
警告：本机运行时，必须保持持续的供水，没有水循环温度将会达到危险点，会引起机内密封圈的损坏。
警告：不要使用本机用于特别寒冷处，以防止冰冻而损坏本机。
警告：此机设备只为清洁水设计，不能使用腐蚀性的化学液体。
警告：不能将本机直接对准人体、宠物及机器本身喷射。
警告：在维修保养时，必须切断电源。
警告：为了确保实用安全，请用最初的备用配件及生产商指定的配件。
假如机器损坏，没有修复以前请不要使用本机。
操作指南－连接软管到出水口，并连接喷抢到软管另一头。
－连接喷头和喷杆。
－查看过滤网是否有障碍物。
－连接供水软管。
－主要技术数据维修保养安装Array连接图１主机２供水软管３水管接合配件４进水口５高压管６自来水龙头７喷枪８电源插头注意：假如产品更新，公司将保留没有预先通知的情况下，修改说明书的权利。
高压清洗机手册（M12110 M12230）说明书
M12110M12230Instruction ManualSpare Parts ManualProduct information................................................................................................Important safety instructions...................................................................................Technical specification............................................................................................Know your machine................................................................................................Working principle....................................................................................................Preparing for use...................................................................................................Assembly...............................................................................................................Brush selection guide............................................................................................Controls..................................................................................................................Operating the machine...........................................................................................Electrical diagram..................................................................................................Accessories...........................................................................................................Upkeep of your PORT A SCRUB...........................................................................Housing - Drive Side...............................................................................................Housing-Idle Side..................................................................................................Pump housing........................................................................................................Lever and guide link mechanism............................................................................Handle group..........................................................................................................Motor,drum and bridge assembly...........................................................................Accessories...........................................................................................................3345556677,88991113,151719212325The Minuteman Machine is an ideal machine to clean floors in small and medium areas like offices,hospitals,restaurants,shopping complexes and many commercial applications.It sprays plain water /detergent solution,scrubs and picks up the dirty water -all in a single pass.The Port A Scrub has different optional brushes to suit a variety of applications.This machine can be used only on smooth even floors like Mosaic,all type of stone floors,PVC,Short-pile carpet,Wood and Profiled Rubber.It should not be used on rough uneven surfaces..PORT ASCRUB Instruction ManualThe machine must be unpacked and assembled in accordance with these instructions before connecting to the electrical supply.This machine should always be connected to a fully grounded power supply of the right voltage and frequency.Keep the power supply cord away from moving parts.During operation,hazard may occur when running machine over the supply cord.The machine must be disconnected from the mains supply (by pulling the plug out)before changing the brushes,cleaning the machine and,for maintenance.Warning!Use only the brushes/accessories strictly as per the instruction age of any other brushes/accessories can cause safety problems.Periodically inspect the cord for possible damage.The damaged cord must be replaced with the special cord available from the manufacturer or an authorized service agent.DO NOT leave the machine connected to the power supply when not in use;always remove the plug from the mains socket.DO NOT use where hazardous dust is present.DO NOT use machine near flammable liquids.DO NOT use in an explosive atmosphere.DO NOT use in gradient surface.DO NOT keep the machine with handle lowered,when the machine is in working mode.Operators must be fully trained in accordance with these instructions,able to perform routine upkeep of the machine and correct selection of brushes.Operators should be physically capable to maneuver transport and operate the machine.DO NOT run the machine dry,as this could damage the floor surface or the machine itself.Take adequate care to hold the machine firmly while installing and removing the brush.Never use excessive foaming or highly corrosive cleaning solutions.While operating on a flooded floor,always ensure that the water level does not exceed 1/4”.DO NOT operate this machine on rough uneven surface like industrial concrete floor.Do not clean the machine using water jet.Ensure all parts are fitted properly before operation.···········Guidelines for the operator (3)4Note:1. Noise levels measured at a distance of 1 meter from machine and 1.6 metres above floor, when washing a hard floor. Measurements recorded using a hand held meter.2. Handle vibration does not exceed 2.5 m/s, when operating on a smooth hard surface.3.Above dimensions are approx. Since the companies policy is to continuously improve the product, there could be changes without prior notice.2986713511412312(1)(2)(3)Tank(4)Bottom handle (5)Dirty water tank(6)Filter (7)Lid Cap (8)Boot(9)Nozzle (10)Conveyor drum (11)Brush (12)PedalTop handleLiquid discharge controlhandle1.Cleaning liquid in the fresh water tank is made to spray on the floor to be washed..2.The counter rotating brushes scrubs the floor and also throws the dirty water on the Conveyor drum.The front brush does most of the scrubbing and drying.The rear brush completes the scrubbing and collects the remaining water off the floor.3.A blade fitted to the dirty water tank wipes the drum.1. Bottom handle2. Machine body3. Pump Housing4. Auxillary Tank5. Top handle &pull cable7. Brush shafts (2)8. Screws & washers 9. Cable retainer 10. Power cord6. Handle LH & RH11. Dirty water tank 12. Hook 13. Knob (10)(11)(12)(7)(8)(9)(6)(2)(3)(4)(5)(1)L E F T B O T TO M R E A RR I GH T B O T TO M R E AR 1.Insert the two tubular handles into the bottom handle and secure them using knob (2Nos)by tightening lightly.Ensure that the handles are assembled according to their marked position and the cable holding hooks are pointing towards the rear.2.Slide the electric cable retainer into the top portion of RH handle.3.Fit the top handle over the tubular handles and secure them with washer and screw (2sets).Ensure that the label on the top handle is facing the front of the machine.Now tighten firmly both the knobs and screws alternately.Insert the dummy caps provided to cover the screws (2nos)in the top handle.4.Pass the free end of the pull cable through the plastic guide in RHHandle.5.Fixthe auxillarytank firmly into the bottom handle by holding the top handle.6.Rotate the knob to hold the auxillary tank.7.The brushes are only loosely packed in the machine for transit,therefore the brush shafts must be fitted before operating the machine.Push the shafts through the brushes from the side of the machine.To remove brushes,push the brush shaft out from the side of the machine using the fingers and withdraw the shaft.Normally standard brush type will be supplied with the machine.Brushes shall be selected according to the type of floor surface to be cleaned,and the degree of dirt to be removed,please refer Brush Selection Guide.8.Now machine is ready for use.6Refer Page 25 for Brush SelectionThis is applicable when the customer has more than one set of brushes of same type.Example :2or more sets of Standard BrushCustomers may not interested to use same brushes in Bedroom /Kitchen /germ free area which is already been used in other areas like Corridor /Bathroom /Oil or chemical deposited areas.It is difficult for the customers to identify the particular brush which is used in certain area.To make this easy,Brush buttons of colors RED,BLUE,WHITE and YELLOW are packed with the machine.Customers shall plug the buttons on the hole provided in the brush as shown.This helps the customer to identify the particular brush by keeping the button (color)as reference.(a) Hole provided for plugging button.(b) Brush with button plugged.By pressing the pedal lightly with your foot,pull back the handle a little to start the motor.The brushes and the drum starts rotating.Pulling the handle further without pressing the pedal,lowers the machine and engages the rotating brushes onto the floor.To stop working,take the handle to the vertical position.By pulling,the liquid discharge control handle up,the cleaning liquid is made to spray on the floor.The spraying stops once the liquid discharge control handle is released.Brush contact with the floor is adjustable in 4steps,contact is MINIMUM when the knob is fully down and MAXIMUM when it is fully raised.This helps you to compensate for the wear of brushes and also to control the scrubbing effect.If there is no machine movement,when the handle lower down fully (working mode),change the knob position to one step up.In the event of motor getting overloaded due to improper power supply or unexpectedobstruction to the brush/drum rotation,the over load protector trips and protects the motor from damage.If this happens,identify the cause,correct it and,reset the protector button after minimum 30seconds from tripping by pressing the over load protector manually and continue working.Slide this knob to TOP position to operate the machine.Slide this knob to BOTTOM position to move the machine from one place to other place and to park the machine.By keeping the knob to top position (working mode)and moving the machine will damage the brushes.Before the washing operation startsRecommended washing sequenceTransport/Working Model ControlBrush Contact ControlCleaning Liquid Discharge ControlMotor Overload Protector1. Fill cleaning liquid in fresh water tank (Fig-i)2. Insert the plug into mains 3-pin socket.3.Ensure that the brushes are fitted properly.4.Slide the transport/working mode control knob to TOP (working) position (Fig-ii).1. Start the machine by pressing the pedal and pulling the handle back.2. Move forward, while sparingly pulling the liquid discharge control handle (Fig-iii).This handle should not be kept pulled all the time.The duration and frequency of pulling and releasing has to be adjusted suitable to match with the type of floor, extent of dirt. etc. For ceramic & granite floors, apply very little water.7(Fig-v)5.When the dirty water tank is full,lift and pull the tank out of the machine (Fig vi).Empty the tank and wash it in running water or dip it in a bucket of water (Fig-vii).Clean the blades and push the tank into its place.1.Move the Transport /Working mode control knob to BOTTOM (Transport)position (Fig-viii).2.Disconnect the power supply by unplugging the electrical plug and wind the cable over cable holders in the handle.3.Pull out the dirty water tank and wash it completely.4.To prevent possible clogging of filter,drain cleaning liquid5.Remove the brushes by pushing the brush shaft out (Fig-ix).6.Wash the brushes either by dipping in a bucket/sink or in running water (Fig-x).7.Turn the machine sideways and wipe clean the conveyor and machine body with a damp cloth (Fig-xi).8.Re-install the brushes after washing.It is easier to push the brush shaft form the right hand side (identified by the electrical cable).9.Keep the machine in the safer place.may not handed overTransporterSide BrushTo get the maximum life of the machine ensure the following.Regularly inspect sheath,plug and cord anchorage for damage or loose connection.For maximum life wash the brushes regularly.Ensure machine is in Transport mode when not in use.Store additional brushes in a vertical position to avoid bending of bristles.Check for permanent bending of bristles in a particular direction.This may occur if the machine is operated for several days without removing the brushes,which is not recommended.If this occurs,reverse the brush so that the bent bristles are automatically straightened.This may wear out after years of use.If this occurs the water collection performance will decrease.It should be replaced by an authorized ServiceAgent.The filter prevents clogging of the spray nozzle and should be periodically e pressurized air/water for cleaning.If the spray of the nozzle become blocked,slide the nozzle cover off and remove nozzle wash in clean water and clean using a pin and refit.·Supply cordBrushesWiper BladeSolution feed filterNozzle maintenance (9)The simply fitted trolley provides for ease of movement when transporting the machine.Installing the Transporter1.With the machine handle in the upright position place the transporter centrally alongside the machine.2.By holding the machine firmly, strap the velcro with the machine to fix the transporter.3.Ensure that the velcro strap properly wrapped around the bottom handle.4.Now the transporter is ready to use.The machine can then be maneuvered easily whilst holding the top handle.To wash the edges,the side brush shall be used.Switch off and unplug the machine before fitting the side brush.1.Remove the front brush and brush shaft.2.Fix the shield assembly and screw it into the side plate and tighten.3.Insert the side brush through the shield and main brush.Fitting the side brushUsing the side brush1.Tilt the machine at an angle move forward.This way,the dirty water thrown bythe side brush will be collected by the rear brush.e side brush only for washing the edges.322524105116116a11115b1949848319539787208880114101919728115a115b111914359427313V81034 9211563V71911193622122774610Housing-Drive Side Spare Parts ManualRef. No PartNoDescription Size Qty1925032CSK SCREW M4x104 2925003CRPH SCREW M3x66 7925051CSK SCREW M6x143 9925114ALLEN SCREW M6x102 10925027ALLEN SCREW M6x167 11925031ALLEN SCREW M6x202 13925033WASHER 4.2x12x1.64 19925056BEARING60032RS9 20925062BEARING6082Z1 24925001BELT5005M1 25925002BELT4255M1 28925012WASHER2 32925018BUMPER1 34925026BUMPER1 42925047BRUSH SLIDER1 43925048SLIDER HOUSING1 46925054SEAL2 49925064PINION1 53925073DRUM SPROCKET1 59925092PIN1 62925099O'RING2 63925102SHIELD1 73925186SELF TAPPING SCREW4 77925130CAP2 80925227GEAR HOUSING1 83925181HOUSING SPROCKET1 84925182SEAL1 87925193GEAR–LH1 88925194GEAR-RH1 92925219SHIELD2 93925220ROLLER2 105925249BUMPER SLEEVE3 111925804BRUSH SPROCKET2 114925813GEAR SPROCKET2 115925815IDLER ASSY1 115a925075SPROCKET1 115b925046HUB2 116925816IDLER ASSY1 116a925061SLEEVE1 212925221STUB AXLE1 V7925150DRIVE HOUSING1 V8925319COVER1V2V3133751094b94a 9412986131132892172736811610039909596999893622123318868171061524218919792774632105V5910V834137358594319263Housing-Idle SideRef. No PartNoDescription Size Qty1925032CSK SCREW M4x104 2925003CRPH SCREW M3x66 6925039CSK SCREW M5x252 9925114ALLEN SCREW M6x102 10925027ALLEN SCREW M6x165 13925033WASHER 4.2x12x1.64 15925100WASHER 6.4x12x1.61 16925151WASHER9x17x1.61 17925110SPRING WASHER M61 18925059TOOTHED WASHER M61 19925056BEARING60032RS2 21925063WIRE TIE3 32925018BUMPER1 33925019BUSH2 34925026BUMPER1 39925040STUB AXLE1 43925048SLIDER HOUSING1 46925054SEAL2 58925083TRANSPORT SLIDER1 59925092PIN1 62925099O'RING2 63925102SHIELD1 68925109FAN COVER1 72925116GROMMET1 73925186SELF TAPPING SCREW6 75925124CAP1 77925130CAP2 79925147STOPPER1 81925500PEDAL1 86925192NUT2 89925199CONNECTOR1 90925200SWITCH2 92925219SHIELD2 93925220ROLLER2 94925529SOCKET ASSY1 94a925074SOCKET1 94b925076TERMINAL3 95925501CABLE1 96925502CABLE1 98925504CABLE1 99925505CABLE1V2V3133751094b94a 9412986131132897273681161003990959699982193622123318868171061524218919792774632105V5910V834137358594319263Housing-Idle SideRef. No PartNoDescription Size Qty100925152SPRING-PEDAL1 105925249BUMPER SLEEVE3 106925161CSK SCREW M4x81 129925015LEVER SWITCH ACT1 131925041INSULATION TOP1 132925044INSULATION BOTTOM1 133925101NUT1 188925207SLEEVE TIE ROD3 212925221STUB AXLE1 242925347CLAMP WIRE1 V2925534CAPACITOR(M12230)1 V3925173CIRCUIT BREAKER(M12110)1 925166CIRCUIT BREAKER(M12230)1 V5925153IDLE HOUSING(M12110)1 925154IDLE HOUSING(M12230)1 V8925319COVER11651871841183M12110185180159124516818116472244V2155101176V9169186182163167158154174173121123123a122b16224724627117010272175177248165270Pump HousingRef. No PartNoDescription Size Qty1925032CSK SCREW M4x105 72925116GROMMET2 101925160O-RING-PUMP1 102925077FILTER1 121925832DIRTY WATER TANK1 122b925162LID PAD2 123925836LID-DIRTY WATER1 123a925132LID-DIRTY WATER1 154925128HOSE-275(10.8)1 155925163INSULATION1 158925164HOSE CLIP1 159925165NOZZLE1 162925167BOOT1 163925168SCREW M3X302 164925169HEX NUT M32 165925170HEX NUT M47 167925187SWITCH2 168925204STRIP LID2 169925224EXTENSION BUSH1 170925233HOSE-165(6.5)2 173925261HOSE CONNECTOR1 174925262BOOT-LID1 175925506CABLE1 176925511ADAPTOR NOZZLE1 177925573CABLE1 180925171SEAL NOZZLE1 181925173BASE SWITCH1 182925174LEVER1 183925175CLAMP1 184925176SUPPORT RING2 185925177PUMP HOUSING1 186925178LID1 187925179SPACER1 245925013CSK SCREW4 270845039WASHER4 V9925210PUMP(M12230)1For M12110244925011CLAMP CAPACITOR(12110)1 246925016GROMMET(M12110)2 247925020PUMP HOUSING(M12110)1 248925021CABLE(M12110)1 271814313CSK SCREW M4X154 v2925536CAPACITOR(12110)1 v9925203PUMP(M12110)1119a118a1196411876264128120120a119a82119297841477691267611345Lever and Guide Link MechanismRef. No PartNoDescription Size Qty4925104CRPH SCREW M4x122 26925008CLEVIS PIN5 29925014CLEVIS PIN1 41925043LINK1 45925053SHIELD8 47925055LEVER2 64925105LEVER BUTTON4 76925129CIRCLIP6 78925139LINK GUIDE1 82925180SPRING1 91925212BUSH1 113925810WHEEL4 118925822LEVER ASSY1 118a925085LEVER1 119925823LEVER ASSY2 119a925086LEVER2 120925824LEVER ASSY1 120a925087LEVER1 128925050LEVER SWITCH1V423355718936010415344711211748114135126124172160160a 160c 160b 179161d 161161c 161b 161a 15222423173229225732306545222522722866224226Handle GroupRef. No PartNoDescription Size Qty3925058CRPH SCREW M4x81 4925104CRPH SCREW M4x1210 11925031ALLEN SCREW M6x202 12925088WASHER 6.4x18x24 23925098CABLE RETAINER1 35925028CLAMP1 44925049PULL HANDLE1 48925057CAP1 52925069BASE-CABLE HOLDER2 57925082CLAMP1 60925096NUT1 65925106SPRING6 66925107WASHER6 71925115PLUG2 73925186SELF TAPPING SCREW10 104925184PULL CABLE-P1 117925818TOP HANDLE1 126925103KNOB2 135925089BOTTOM HANDLE1 152925127GASKET1 153925111TANK-4l1 160925117BASE VALVE1 160a925118BASE1 160b925119SEAL1 160c925120CAP-VALVE1 161925135VALVE1 161a925122BODY-VALVE1 161b925540SEAL1 161c925123SPRING1 161d925125CAP-SPRING1 172925260PLATE1 179925126NUT1 189925274SLEEVE1 224925305KNOB-CABLE HOLDER-II2 225925306KNOB-CABLE HOLDER-I2 226925307KNOB-TANK HOLDER-LH1 227925308KNOB-TANK HOLDER-RH1 228925339BASE-CABLE AND TANK HOLDER2 229925340GUIDE1 230928633PIPE-LH1 231928634PIPE-RH1 V4925922(M12116)POWER CORD1 925920(M12235)POWER CORD1 925923(M12235)POWER CORD-UK1134134b134aV6287V15011227315415556623755381422677069851Motor, Drum and Bridge AssemblyRef. No PartNoDescription Size Qty5925136HEX NUT M63 7925051CSK SCREW M6x144 8925090ALLEN SCREW M4x102 14925080WASHER 5.2x10x1.62 15925100WASHER 6.4x12x1.63 22925084GRUB SCREW M5x122 27925009BUSH4 28925012WASHER4 31925017WASHER6 37925037SPRING1 38925038SPRING1 50925065HEX SHAFT2 51925068WASHER2 54925078TIE ROD3 55925079SHAFT1 56925081ROLLER6 62925099O'RING12 67925108BUSH2 69925112BUSH1 70925113BUSH1 112925808BRUSH SHAFT2 134925067DRUM ASSY1 134a925070DRUM1 134b925071DRUM SLEEVE1 V1925762MOTOR(M12110)1 925761MOTOR(M12230)1 V6928548BRIDGE1AccessoriesSide Brush Group-3423456176886a6a6b6c9112101011103254TransporterAccessories1234566a 6b 6c 789101112925881925155925156925157925158925137925138925140925141925159925142925143925144925878925879FRAME CLAMPFIXED STRIP (VELCRO)FLEXIBLE STRIP(VELCRO)PLATE TYREBUSH-WHEEL RIM WHEEL RIM TYRE-MAIN WHEEL CAP WHEEL WASHER CIRCLIP A17x1CRPH SCREW M4x25STOPPER TOP STOPPER BOTTOM925904-TRANSPORTER 111112422242612SL NO PART NO DESCRIPTIONQTY12345925901925902925903925908925990BRUSH GROUP-STD BRUSH GROUP-POLISHING BRUSH GROUP-SCRUBBINGBRUSH GROUP-ESCALATOR (NYLON)BRUSH GROUP-ESCALATOR (SILICON CARBIDE)BRUSH GROUP SL NO PART NO DESCRIPTION123456SHIELD BUSH SHAFT SIDE BRUSH WASHERALLEN SCREW M5x20SIDE BRUSH GROUP DESCRIPTION SL.NOQTY 925766925172925764925855925145925146925907STANDARD 925766925172925764925595925145925146925927ESCALATOR 111111Note:Since the companies policy is to continuously improve the product, these could be changed without prior notice.Minuteman International Made Simple Commercial Limited WarrantyREVISION DEFFECTIVE 7/1/2008Minuteman International, Inc. warrants to the original purchaser/user that the product is free from defects in workmanship and materials under normal use. Minuteman will, at its option, repair or replace without charge, parts that fail under normal use and service when operated and maintained in accordance with the applicable operation and instruction manuals.All warranty claims must be submitted through and approved by factory authorized repair stations.This warranty does not apply to normal wear, or to items whose life is dependent on their use and care, such as belts, cords,switches, hoses, rubber parts, electrical motor components or adjustments. Parts manufactured by Minuteman are covered by and subject to the warranties and/or guarantees of their manufacturers. Please contact Minuteman for procedures in warranty claims against these manufacturers.-- Use of replacement filters and/or prefilters not manufactured by Minuteman or itsdesignated licensees, will void all warranties expressed or implied.A potential health hazard exists without original equipment replacement.All warranted items become the sole property of Minuteman or its original manufacturer, whichever the case may be.Minuteman disclaims any implied warranty, including the warranty of merchantability and the warranty of fitness for a particular purpose. Minuteman assumes no responsibility for any special, incidental or consequential damages.This limited warranty is applicable only in the U.S.A. and Canada, and is extended only to the original user/purchaser of this product. Customers outside the U.S.A. and Canada should contact their local distributor for export warranty policies.Minuteman is not responsible for costs or repairs performed by persons other than those specifically authorized byMinuteman.This warranty does not apply to damage from transportation, alterations by unauthorized persons, misuse or abuse of the equipment, use of non-compatible chemicals, or damage to property, or loss of income due to malfunctions of the product.If a difficulty develops with this machine, you should contact the dealer from whom it was purchased.This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion or limitation of special, incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions and limitations may not apply to you.MPV 13, one year partsV-14, One year parts, one year laborMPV 14 and 18, two years parts, one year labor RapidAir blower, one year parts, one year laborExplosion-Proof Vacuum, one year parts, one year labor Pneumatic Vacuums, three years parts, one year labor TRS 14, one year parts, one year labor(Not to exceed two hours)(Not to exceed two hours)(Not to exceed two hours)Ninety days0-3 months replacement, 4-12 months pro-rate Ten years, no additional labor111 South Rohlwing Road Addison, Illinois 60101 USA Phone 630- 627-6900Fax 630- 627-1130Special warning to purchaser Three years parts, two years labor, ninety days travel (Not to exceed two hours)Port-A-Scrub, one year parts, six months laborThree years parts, two years labor, ninety days travelSweepers, one year parts, one year labor, ninety days travelOne year parts, one year labor, ninety day travelOne year replacement Cord Electric Group……….Battery Operated Group…..Internal Combustion Group….Battery Chargers Replacement Parts Batteries Polypropylene Plastic Tanks Exceptions……….Exceptions……………………. ..EX 12 and EX12H, one year parts, one year labor ……………..………………………….…European Representative Andre VonkHako-Minuteman-PowerBoss PO Box 174。
高压清洗机操作手册
高压清洗机操作手册一、产品介绍高压清洗机是一种专业的清洗设备，通过高压水流将污垢、油渍、灰尘等附着在不同表面上的污染物迅速清除。
本操作手册旨在向用户介绍高压清洗机的基本操作方法和注意事项，以确保安全使用和提高清洗效果。
二、安全须知1. 在操作高压清洗机前，请务必熟悉本操作手册的所有内容，并确保操作人员具备相关的安全知识。
2. 在使用高压清洗机时，应穿戴适当的防护服装、安全帽、防滑鞋等个人防护装备。
3. 切勿将高压水流对准人体、动物或其他易受伤害的物体，以避免事故发生。
4. 操作时应确保清洗区域周围没有其他人员，以免引发意外伤害。
5. 在清洗机运行期间，不得随意拆卸或更换零部件，以避免损坏机器或导致操作不当。
三、操作步骤1. 准备工作a. 将高压清洗机放置在平坦、稳固的地面上。
b. 检查电源线、水源接口等连接是否牢固，确保正常供电和供水。
c. 打开水源阀门，排除管道中的气体，直至水流稳定。
2. 启动高压清洗机a. 按下电源开关，确认电源指示灯点亮。
b. 调整调压阀，将出水压力调至所需水压范围内。
c. 启动高压清洗机的气缸或泵，观察机器是否工作正常。
3. 进行清洗a. 将喷枪对准需要清洗的区域，保持适当的距离（根据清洗机型号和清洗对象的不同而有所差异，需参考机器说明书）。
b. 按下喷枪扳机，启动高压水流，进行清洗。
c. 清洗时需保持喷枪平稳移动，避免过度集中清洗造成表面损坏。
4. 完成清洗a. 清洗完成后，释放喷枪扳机，关闭清洗机电源开关。
b. 关闭水源阀门，切断供水。
c. 将高压清洗机存放在安全、干燥的地方，避免损坏和意外发生。
四、注意事项1. 使用高压清洗机时，尽量选择合适的清洗剂，以提高清洗效果。
2. 清洗时注意保护周围环境，避免水流对植物、动物等造成不必要的伤害。
3. 长时间使用高压清洗机时，需定期检查电源线、水管、喷嘴等部件是否存在磨损或故障，并及时维修或更换。
4. 遇到异常情况时（如异响、漏水等），应立即停止使用，并联系专业人员进行检修。
凱馳K5 高壓清洗機中文說明書说明书
1德國凱馳家用高壓清洗機K 5 中文說明書(一) 主機本體與配件名稱1. 快速接頭轉接環2. 高壓管快速接口3. 進水口(含過濾裝置)4. 電源開關ON/OFF5. 大型手提把6. 配件收納網7. 配件收納處8. 主機電源線9.清潔劑吸管附過濾嘴10. 大型滾輪與輪栓 11. 高壓槍把12. 高壓槍把安全鎖 13. 高壓管移除鎖 14. 高壓管 15. 螺旋噴桿16. 高低壓可調噴桿17. 自購水管，主機使用一般/棉質4分水管18.高壓槍把固定架(二) 安全提示使用本產品前，請遵守下列基本安全事項 - 第一次使用前，請務必詳閱本說明書。
- 請了解主機安裝、操作高壓與關閉主機方式。
- 請勿於身體不適時操作主機，以免發生危險。
- 請遵守本說明之配件使用、保養與維修資訊。
(三) 使用前 組件安裝步驟A 、安裝主機滾輪步驟B 、將主機手提把安裝於主機上，槍把固定架安裝於主機側邊步驟C 、安裝配件收納網，將收納網分別掛於兩側勾環內安裝快速進水接頭步驟D 、將高壓管插入噴槍內直到聽到「喀」 的聲音。
安裝後輕拉高壓管確認安裝妥當。
拆除高壓管與噴槍連接：按下高壓管移除鎖將高壓管移除。
步驟E/F 、將高壓管另一端直接插入主機高壓管快速接頭內並聽到「喀」確認已經固定。
移除高壓管時請將高壓快速接頭往外按壓拔除高壓管即可。
2步驟G 、安裝前請確實將槍把安全鎖鎖上。
安裝噴桿，請依照槍桿孔型將噴桿按壓入槍把孔內後逆時針方向鎖緊。
注意:請確認槍桿已確實固定於槍把上，以免造成危險。
步驟H 、使用清潔劑自吸功能。
請先行安裝高低壓可調式噴桿後。
將清潔劑吸管從主機後下方輕拉出，插入清潔劑中。
使用時請將高低壓噴桿調置低壓設定方能進行自吸清潔劑，清潔劑自吸需啟動槍把後1-2分鐘出清潔劑才會噴射出。
注意:請勿使用粉狀或過於濃稠清潔劑(沙拉脫)步驟I 、將大型手提把拉出移動，請確實拉出後聽到「喀」聲音表示固定。
收回時請往下按壓把手縮回把手。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
高压清洗机说明书 Prepared on 22 November 2020
高压清洗机说明书
型号:TVE070C、TVF070C
TVB080G、TVD100C
TVG100C
使用本机之前，请先阅读说明书
适用范围
我们的高压清洗机是专业化，多功能又有可靠的安全保障的机器。
适用于汽车、自行车、户外设备、花园和温室等的清洗。
安全手则
警告：使用本产品前，请先阅读说明书。
警告：为减少受伤风险，当靠近儿童操作时，应严格看管本机。
未经训练的人员和儿童不得操作本机。
警告：应了解快速开关机，并熟悉本机全部功能。
警告：操作时，应保持警惕和看管好本机。
警告：不要在疲惫、醉酒和药物作用下，操作本机。
警告：保持操作区无其他人。
警告：不要将本机延伸过远，或摆放在不牢固的支撑上，要保持本机平衡。
警告：理解说明书上的全部保养及维修知识。
警告：本新产品提供接地故障电路断流器在电源插头处，如果需要替换电源线及插头请使用相同的部件。
警告：本产品必需接地。
当本机在出现故障或损坏而漏电时，接地可以防止触电事故发生。
插头必须插在合适的插座并插紧，应用的额定电压必须与当地的供应电压相一致。
警告：如果你对是否适合接地有疑问，请找有资格的电工或服务人员检验。
不要修改已供给的电源插头，如果插座不适合，请找有资格的电工安装插座。
不能用任何改造的电源插头用于本机。
警告：当用于室外操作时，插座必须是防水结构，延长线必须有室外使用的认证标志，不用时存放在室内。
本机供应电流应不少于额定电流。
使用前，请先检查延长电线，如果已损坏，请更换。
使用不适合的外延电线会有很大的危险。
不要滥用延长电线，拔插头时请不要猛拉电线。
延长电线远离热源及锋利刀口。
分离本机时，请先将插头从插座处分离。
警告：如果供给电线已损坏，必须使用专用的电线，也可让销售商或生产厂家重新装配。
警告：为了减少触电风险，在下雨和雷雨天气不要开启和操作本机。
保持所有接口干燥，并脱离地面，不要用湿手触摸插头，严禁水渗透本机。
警告：本机运行时，必须保持持续的供水，没有水循环温度将会达到危险点，会引起机内密封圈的损坏。
警告：不要使用本机用于特别寒冷处，以防止冰冻而损坏本机。
警告：此机设备只为清洁水设计，不能使用腐蚀性的化学液体。
警告：不能将本机直接对准人体、宠物及机器本身喷射。
警告：在维修保养时，必须切断电源。
警告：为了确保实用安全，请用最初的备用配件及生产商指定的配件。
假如机器损坏，没有修复以前请不要使用本机。
操作指南
－连接软管到出水口，并连接喷抢到软管另一头。
－连接喷头和喷杆。
－查看过滤网是否有障碍物。
－连接供水软管。
－检查是否连接好。
－喷出水试一下，检查是否漏水。
－压下板机，通过抽水机和软管去除空气，然后锁上板机。
－插上本机电源，按“O”开启开关。
－解开枪锁，使用高压清洗机。
可调节喷头
水可以从喷头喷出直线（图1）或扇形（图2），首先开启压力机然后调整喷头。
用手旋转塑圈
进水口网筛
进水口过滤网要定时检查，以避免阻塞而限制抽水机供水（图3）
长期保存
本机应存放在无霜冻的环境
长时期不使用机器，可能形成水垢使机器很难开启。
在这种情况下，应关掉本机，用手旋转电机数圈，以避免电流过大，致使开关损坏（图4）。
主要技术数据维修保养
安装连接图
１主机２供水软管３水管接合配件４进水口５高压管６自来水龙头７喷枪８电源插头
注意：假如产品更新，公司将保留没有预先通知的情况下，
修改说明书的权利。