汽车冲压件中英文名称对照表
汽车冲压件 英文名称
24 左前纵梁后部本体加强板
FRONT-RAIL-EXTENSION-REINF-LH
25 右前纵梁后部本体加强板
FRONT-RAIL-EXTENSION-REINF-RH
26
左前纵梁前部内板
FRONT-INNER-RAIL-LH
27
右前纵梁前部内板
FRONT-INNER-RAIL-RH
28
后悬安装支架
ATTACH-ENGINE-REINFORCEMENT-RH
33
左前纵梁后部本体
FRONT-RAIL-EXTENSION-LH
34
右前纵梁后部本体
FRONT-RAIL-EXTENSION-RH
35
后纵梁左连接板
REAR-RAIL-CROSSMEMBER-BRACKET-LH
36
后纵梁右连接板
REAR-RAIL-CROSSMEMBER-BRACKET-RH
112
前挡板上加强梁
UPPER-DASH-PANEL-CROSSMEMBER
113
前端左安装支架
FRONT-BEAM-BUMPER-ATTACH-BRACKET-LH
114
前端右安装支架
FRONT-BEAM-BUMPER-ATTACH-BRACKET-RH
115
制动液壶安装支架
OIL-TANK-BRACKET
42
右后纵量侧盖板
REAR-RAIL-LATERAL-COVER-RH
43
左后纵梁后部
REAR-RAIL-EXTENSION-LH
44
右后纵梁后部
REAR-RAIL-EXTENSION-RH
45
后制动油管支架
冲压件中英文对照表
右侧A 柱上隔板DIAPHRAGM - "A" PILLAR UPR RH右前门内板加强板REINF - INNER, FRT DOOR, RH仪表板横梁左支架SUPPORT - TIE BAR LH左侧围外下板PANEL - SIDE OUTER LWR LH左侧A 柱上隔板DIAPHRAGM - "A" PILLAR UPR LH油箱-上部FUEL TANK - UPPER HALF仪表斑横梁右侧安装支架SIDE SUPPORT - I.P.TO "A"PILLAR RH 后上板后横梁右支架SUPPORT - FRAME,BACK PNL UPR RR RH 右侧A 柱支撑加强板REINF - SUPPORT FRONT PILLAR RH油箱-下部FUEL TANK - LOWER HALF仪表板横梁左侧安装支架SIDE SUPPORT - I.P.TO "A"PILLAR LH 后上板后横梁左支架SUPPORT - FRAME,BACK PNL UPR RR LH 左侧A 柱支撑加强板REINF - SUPPORT FRONT PILLAR LHA 柱加强板-右REINF - FRONT PILLAR RH右前纵梁内加强板REINF - LONGITUDINAL FR INR RH顶盖前横梁RAIL - WINDSHIELD HEADER右侧A 柱内板PANEL - "A" PILLAR INNER RHA 柱加强板-左REINF - FRONT PILLAR LH左前纵梁内加强板REINF - LONGITUDINAL FR INR LH顶盖中横梁SUPPORT - ROOF CENTER FRT左侧A 柱内板PANEL - "A" PILLAR INNER LHA柱上加强板REINF - FRONT PILLAR UPR RH前纵梁隔板加强板REINF - SIDE CLOSURE顶盖后横梁FRAME - ROOF REAR右侧B 柱加强板PANEL - "B" PILLAR, RHA 柱上加强板REINF - FRONT PILLAR UPR LH右前纵梁隔板CLOSURE - LONGI. INTERM. RH顶盖PANEL - ROOF左侧B 柱加强板PANEL - "B" PILLAR, LH右前门上铰链加强板REINF - FRT DOOR HINGE UPPER RH左前纵梁隔板CLOSURE - LONGI. INTERM. LH右侧围前下连接板PATCH - LOWER FRONT RH右侧围内板PANEL - SIDE INNER, RH左前门上铰链加强板REINF - FRT DOOR HINGE UPPER LH前隔板内板PANEL - DASH LOWER INNER左侧围前下连接板PATCH - LOWER FRONT LH左侧围内板PANEL - SIDE INNER, LH右前门下铰链加强板REINF - FR DOOR HINGE LOWER RH前隔板PANEL - BULKHEAD右侧围外板PANEL - SIDE, OTR RH天线安装支架BRKT - ANTENNA FIXING左前门下铰链加强板REINF - FR DOOR HINGE LOWER LH前隔板上盖板DASH PANEL TOP ASM左侧围外板PANEL - SIDE, OTR LH顶盖与右侧纵梁后结合面加强板REINF - JUNCTION,ROOF RAIL RH顶盖右侧纵梁RAIL - ROOF SIDE RH仪表板上板PANEL - DASH UPPER左前轮罩上纵梁连接板PATCH - LONGITUDINAL FR UPR LH顶盖与左侧纵梁后结合面加强板REINF - JUNCTION,ROOF RAIL LH顶盖左侧纵梁RAIL - ROOF SIDE LH前隔板上支架加强件BRKT - DASH UPR REINF.右前轮罩上纵梁连接板加强板REINF - INNER LONGITUDINAL FR UPR RH 右侧围后部内撑件GUSSETT - SIDE PANEL, RR INR, RH右B 柱内板PANEL - "B" PILLAR INNER RH前隔板下连接板PATCH - DASH LWR CTR左前轮罩上纵梁连接板加强板REINF - INNER LONGITUDINAL FR UPR LH 左侧围后部内撑件GUSSETT - SIDE PANEL, RR INR, LH左B 柱内板PANEL - "B" PILLAR INNER LH右侧前下纵梁LONGITUDINAL - INTERMEDIATE FR LWR RH右前轮罩后部内板PANEL - W/HOUSE REAR INNER RH右侧围后部外下板PANEL - SIDE OTR LWR RH右侧门铰链和座椅安全带加强板REINF - SEAT BELT AND DR HINGE RH 左侧前下纵梁LONGITUDINAL - INTERMEDIATE FR LWR LH左前轮罩后部内板PANEL - W/HOUSE REAR INNER LH左侧围后部外下板PANEL - SIDE OTR LWR LH左侧门铰链和座椅安全带加强板REINF - SEAT BELT AND DR HINGE LH 仪表板隔板PLATE - BULKHEAD, DASH PANEL右前轮罩前部内板PANEL - W/HOUSE FRONT INNER RH后上板右前支撑板SUPPORT - BACK PANEL UPR FRAME TO SIDE INR RH 右侧门槛加强板REINF - ROCKER RH仪表板中心支架BRKT - CENTER INSTRUMENT PANEL左前轮罩前部内板PANEL - W/HOUSE FRONT INNER LH后上板左前支撑板SUPPORT - BACK PANEL UPR FRAME TO SIDE INR LH 左侧门槛加强板REINF - ROCKER LH电喷ECU安装支架BRKT-INJECTION ECU MOUNTING右前纵梁LONGITUDINAL - FRONT RH右前座椅安全带加强件REINF - SEAT BELT FRONT RH右侧"A"柱内下板PANEL - FRT PLR INR LWR - RH地板通道前上加强板REINF - TUNNEL UPR FRONT左前纵梁LONGITUDINAL - FRONT LH左前座椅安全带加强件REINF - SEAT BELT FRONT LH左侧"A"柱内下板PANEL - FRT PLR INR LWR - LH转向管柱上支架BRKT - UPR STRG COLUMN右前部下纵梁LONGITUDINAL - FRONT LOWER RH后上板右连接板SUPPORT - REAR RH右后轮罩侧围加强板REINF - SIDE, W/HOUSE RH转向管柱下支架BRKT - LWR STEERING COLUMN左前部下纵梁LONGITUDINAL - FRONT LOWER LH后上板左连接板SUPPORT - REAR LH左后轮罩侧围加强板REINF - SIDE, W/HOUSE LH前地板PANEL - FRONT FLOOR右前纵梁加强板REINF - LONGITUDINAL RH右后门门闩加强件REINF - STRIKER, RR DOOR RH右前轮罩上纵梁LONGITUDINAL - FRONT UPPER RH地板右侧纵梁LONGITUDINAL - FLOOR CENTER RH SIDE左前纵梁加强板REINF - LONGITUDINAL LH左后门门闩加强件REINF - STRIKER, RR DOOR LH左前轮罩上纵梁LONGITUDINAL - FRONT UPPER LH地板左侧纵梁LONGITUDINAL - FLOOR CENTER LH SIDE前保险杠辅助支架BRKT - ATTACH FR BUMPER前后门闩固定件CAGE - STRIKER, FR&RR DOORS RH/LH右减振器定位板LOCATOR - S/ABS RH地板右侧围板PANEL - FLOOR SIDE RH发动机舱后上部右侧密封条支架PATCH - LONGTITUDINAL & DASH LWR RH 右尾灯后上板PANEL - TAIL LAMP REAR UPR RH左减振器定位板LOCATOR - S/ABS LH地板左侧围板PANEL - FLOOR SIDE LH发动机舱后上部左侧密封条支架PATCH - LONGTITUDINAL & DASH LWR LH 左尾灯后上板PANEL - TAIL LAMP REAR UPR LH右前轮罩板PANEL - W/HOUSE FRONT REAR RH地板通道上加强件REINF - TUNNEL UPR REAR发动机右侧安装上支座BRKT - ENGINE MOUNT UPPER RH右C 柱加强件REINF - "C" PILLAR RH左前轮罩板PANEL - W/HOUSE FRONT REAR LH前座椅前横梁C/MBR - FRONT SEAT FRONT右后纵梁LONGITUDINAL - REAR RH左C 柱加强件REINF - "C" PILLAR LH安装仪横梁右侧安装支架BRACKET - SIDE,FIX I.P. RH右前座椅后横梁C/MBR - FRONT SEAT REAR RH左后纵梁LONGITUDINAL - REAR LH燃油加注口支架BRKT - ACTUATOR FUEL FILLER仪表板横梁左侧安装支架BRACKET - SIDE,FIX I.P. LH左前座椅后横梁C/MBR - FRONT SEAT REAR LH座椅安全带加强板REINF - SEAT BELT行李箱内饰支架BRKT - TRIM,TRUNK右前轮罩上纵梁连接板PATCH - LONGITUDINAL FR UPR RH前座椅后安装点内加强板REINF - INR. RR C/MBR FR SEAT SUPPORT右后纵梁侧围板PANEL - SIDE， RR LONGITUDINAL RH右后轮罩内加强板PATCH - W/HOUSE INNER RH左后轮罩内板W/HOUSE - REAR INNER LH右前座椅后横梁外加强板REINF - OTR. RR C/MBR FR SEAT SUPPORT RH左后纵梁侧围板PANEL - SIDE， RR LONGITUDINAL LH左后轮罩内加强板PATCH - W/HOUSE INNER LH右后轮罩内连接板EXTENSION - W/HOUSE INNER RH左前座椅后横梁外加强板REINF - OTR. RR C/MBR FR SEAT SUPPORT LH 座椅加强板REINF - FRONT SEAT右后轮罩内板W/HOUSE - REAR INNER RH左后轮罩内连接板EXTENSION - W/HOUSE INNER LH座椅安全带固定支座加强板REINF- SEAT BELT ANCHOR悬架安装导套加强板REINF - THREADED GUIDE后悬架左前右后安装加强件REINF - FIX REAR SUSPENSION LH FRT/RH RR 燃油加注口FUEL FILLER中地板PANEL - REAR FLOOR FRONT右后纵梁加强件REINF - LONGITUDINAL RH右侧前密封条安装支架BRKT - SEAL RETENTION RH右侧尾灯灯罩板PANEL - TAIL LAMP HSG RH后地板PANEL - REAR FLOOR REAR左后纵梁加强件REINF - LONGITUDINAL LH左侧前密封条安装支架BRKT - SEAL RETENTION LH左侧尾灯灯罩板PANEL - TAIL LAMP HSG LH后地板前横梁C/MBR - REAR FLOOR CENTER后桥右侧安装支架BRKT - REAR AXLE INR RH右侧前翼子板FENDER - RH后保险杠右安装板PANEL - REAR BUMPER LWR RH中地板前横梁C/MBR - REAR FLOOR FRONT后桥左侧安装支架BRKT - REAR AXLE INR LH左侧前翼子板FENDER - LH后保险杠左安装板PANEL - REAR BUMPER LWR LH排气管支架加强板REINF - BRKT EXHAUST TUBE隔热板支架BRKT-HEAT SHIRLD右前翼子板后连接板PATCH - FRONT FENDER RR RH后座背板横梁右支架SUPPORT - C/MBR REAR SEAT BACK RH右前门外板PANEL - OTR, FRONT DOOR, RH右后纵梁内加强板REINF - INNER, LONGITUDINAL RH左前翼子板后连接板PATCH - FRONT FENDER RR LH后座背板横梁左支架SUPPORT - C/MBR REAR SEAT BACK LH左前门外板PANEL - OTR, FRONT DOOR, LH左后纵梁内加强板REINF - INNER, LONGITUDINAL LH水箱横梁右支架SUPPORT -C/MBR RAD,OTR RH右后减振器支架SUPPORT - SHOCK ABSORBER RH右前门外加强板REINF - OUTER, FRT DOOR, RH后保险杠右侧加强件REINF - REAR BUMPER RH水箱横梁左支架SUPPORT -C/MBR RAD,OTR LH左后减振器支架SUPPORT - SHOCK ABSORBER LH左前门外加强板REINF - OUTER, FRT DOOR, LH后保险杠左侧加强件REINF - REAR BUMPER LH发动机舱前部上横梁PANEL - FRONT, UPPER减振器支架加强板REINF - SUPPORT S/ABSORBER RH/LH前门内把手安装支架BRKT - FIX HANDLE, FRONT DOOR后驻车固定点BRKT - VEHICLE ANCHORAGE发动机舱前部右立柱SUPPORT-FRT PNL SIDE RH前保险杠支架BRKT-FRONT BUMPER右后门内板PANEL - INNER, REAR DOOR, RH纵梁制动管支架BRKT - BRAKE TUBES ON LONGITUDINAL发动机舱前部左立柱SUPPORT-FRT PNL SIDE LH发动机前下纵梁加强板REINF - FR LONGIT UNDER ENGINE左后门内板PANEL - INNER, REAR DOOR, LH右后座椅安全带加强板REINF - LATERAL SEAT BELT RH水箱后横梁C/MBR - RAD,RR发动机盖右侧铰链加强板REINF - HOOD HINGE RH右后门内板加强板REINF - INNER, RR DOOR, RH左后座椅安全带加强板REINF - LATERAL SEAT BELT LH水箱前横梁C/MBR- RAD,FRT发动机盖左侧铰链加强板REINF - HOOD HINGE LH左后门内板加强板REINF - INNER, RR DOOR, LH右侧推力杆安装支架REINF - BRKT RR AXLE RH发动机舱前部中立柱SUPPORT - FRT PNL , CTR发动机盖铰链安装板PLATE - HOOD HINGE右后门铰链立柱板PILLAR - HINGE, REAR DOOR, RH左侧推力杆安装支架REINF - BRKT RR AXLE LH水箱横梁右侧支架SUPPORT - C/MEMBER RAD INR RH发动机仓前部右侧上连接板PANEL-FRONT,UPPER RH左后门铰链立柱板PILLAR - HINGE, REAR DOOR, LH后上板PANEL - BACK UPPER水箱横梁左侧支架SUPPORT - C/MEMBER RAD INR LH发动机仓前部左侧上连接板PANEL-FRONT,UPPER LH玻璃导轨支架BRKT - RAIL, GLASS GUIDE后隔板PANEL - RR SEAT RR左前轮罩延伸板W/HOUSE EXTENSION - FRONT LH右前伸轮罩板PANEL - W/HOUSE EXTENSION FRONT RH右后门门闩加强板REINF - LATCH, DOOR, RH后上板后横梁FRAME - BACK PNL UPR RR发动机左侧下安装支架加强板REINF BRKT - ENGINE MTG LOWER LH 左前伸轮罩板PANEL - W/HOUSE EXTENSION FRONT LH左后门门闩加强板REINF - LATCH, DOOR, LH后上板前横梁FRAME - BACK PANEL UPR FRT发动机右侧下安装支架BRKT - ENGINE MOUNT LOWER RH右前轮罩延伸板W/HOUSE EXTENSION - FRONT RH右后门外板PANEL - OUTER, REAR DOOR, RH后部下围板PANEL - BACK LWR发动机左侧下安装支架（左）BRKT - ENGINE MTG LWR LH后悬架左后右前安装加强件REINF - FIX REAR SUSPENSION LH RR/RH FRT 左后门外板PANEL - OUTER, REAR DOOR, LH后部下围板加强件REINF BACK PANEL LWR仪表板横梁右支架SUPPORT - TIE BAR RH右侧围外下板PANEL - SIDE OUTER LWR RH右后门外板加强板REINF - OUTER, REAR DOOR, RH右侧尾灯灯座加强板REINF PANEL- TAIL LAMP HSG RH左前门门闩加强板REINF - LATCH, FRONT DOOR, LH左右行李箱铰链加强板REINF - HINGE, TRUNK, LH左后门外板加强板REINF - OUTER, REAR DOOR, LH左侧尾灯灯座加强板REINF PANEL- TAIL LAMP HSG LH盖板右侧铰链加强板REINF - HINGE, HOOD, RH行李箱铰链安装板SPACER - HINGE, MOBILE, TRUNK后门内把手安装支架BRKT - FIX HANDLE, DOOR行李箱锁钩加强板REINF - LATCH盖板左侧铰链加强板REINF - HINGE, HOOD, LH行李箱安装铰链加强板REINF - FIXED HINGE, TRUNK后门三角窗玻璃下支架SUPPORT - FIXED GLASS LWR后围右侧支撑板SUPPORT - REAR BULKHEAD RH气弹簧支架BRKT - GAS SPRING盖板内板PANEL - INNER HOOD行李箱内板PANEL - INNER TRUNK后围左侧支撑板SUPPORT - REAR BULKHEAD LH盖板闩眼加强板REINF - STRIKER, HOOD盖板外板PANEL - OUTER HOOD行李箱隔板PANEL - CLOSUIE TRUNK备胎螺栓支架SUPPORT - BOLT, SPARE WHEEL带天窗的顶盖PANAL - ROOF OUTER，OPENING ROOF左前门铰链立柱板PILLAR - HINGE, FRT DOOR, LH行李箱盖闩加强板REINF - LATCH TRUNK LID空调与仪表板连接左支架BRKT-FIX HVAC TO PANEL DASH UPPER LH天窗骨架FRAME - SUN ROOF HOUSING右前门门闩加强板REINF - LATCH, FRONT DOOR, RH行李箱上部外板PANEL - OUTER TRUNK UPPER空调与仪表板连接右支架BRKT-FIX HVAC TO PANEL DASH UPPER RH右侧座椅安全带加强板REINF - SEAT BELT RH右前门铰链立柱板PILLAR - HINGE, FRT DOOR, RH行李箱下部外板PANEL - OUTER TRUNK LOWER右前门内板PANEL - INNER, FRONT DOOR, RH左侧座椅安全带加强板REINF - SEAT BELT LH左前门内板加强板REINF - INNER, FRT DOOR, LH左右行李箱铰链加强板REINF - HINGE, TRUNK, RH左前门内板PANEL - INNER, FRONT DOOR, LH。
冲压模具-冲压名称类英汉对照.doc
冲压模具-冲压名称类英汉对照plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具英语解释一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round (full/half runner)流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance 模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode模具相关英语1padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机钟work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板模具相关英语2baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave 凹convex凸short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill钻boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边模具相关英语3emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具常用塑料英语缩略语英文简称英文全称中文全称ABA Acrylonitrile-butadiene-acrylate 丙烯腈/丁二烯/丙烯酸酯共聚物ABS Acrylonitrile-butadiene-styrene 丙烯腈/丁二烯/苯乙烯共聚物AES Acrylonitrile-ethylene-styrene 丙烯腈/乙烯/苯乙烯共聚物AMMA Acrylonitrile/methyl Methacrylate 丙烯腈/甲基丙烯酸甲酯共聚物ARP Aromatic polyester 聚芳香酯AS Acrylonitrile-styrene resin 丙烯腈-苯乙烯树脂ASA Acrylonitrile-styrene-acrylate 丙烯腈/苯乙烯/丙烯酸酯共聚物CA Cellulose acetate 醋酸纤维塑料CAB Cellulose acetate butyrate 醋酸-丁酸纤维素塑料CAP Cellulose acetate propionate 醋酸-丙酸纤维素CE Cellulose plastics, general 通用纤维素塑料CF Cresol-formaldehyde 甲酚-甲醛树脂CMC Carboxymethyl cellulose 羧甲基纤维素CN Cellulose nitrate 硝酸纤维素CP Cellulose propionate 丙酸纤维素CPE Chlorinated polyethylene 氯化聚乙烯CPVC Chlorinated poly(vinyl chloride) 氯化聚氯乙烯CS Casein 酪蛋白CTA Cellulose triacetate 三醋酸纤维素EC Ethyl cellulose 乙烷纤维素EMA Ethylene/methacrylic acid 乙烯/甲基丙烯酸共聚物EP Epoxy, epoxide 环氧树脂EPD Ethylene-propylene-diene 乙烯-丙烯-二烯三元共聚物EPM Ethylene-propylene polymer 乙烯-丙烯共聚物EPS Expanded polystyrene 发泡聚苯乙烯ETFE Ethylene-tetrafluoroethylene 乙烯-四氟乙烯共聚物EVA Ethylene/vinyl acetate 乙烯-醋酸乙烯共聚物EVAL Ethylene-vinyl alcohol 乙烯-乙烯醇共聚物FEP Perfluoro(ethylene-propylene) 全氟（乙烯-丙烯）塑料FF Furan formaldehyde 呋喃甲醛HDPE High-density polyethylene plastics高密度聚乙烯塑料HIPS High impact polystyrene 高冲聚苯乙烯IPS Impact-resistant polystyrene 耐冲击聚苯乙烯LCP Liquid crystal polymer 液晶聚合物LDPE Low-density polyethylene plastics 低密度聚乙烯塑料LLDPE Linear low-density polyethylene 线性低密聚乙烯LMDPE Linear medium-density polyethylene 线性中密聚乙烯MBS Methacrylate-butadiene-styrene 甲基丙烯酸-丁二烯-苯乙烯共聚物MDPE Medium-density polyethylene 中密聚乙烯MF Melamine-formaldehyde resin 密胺-甲醛树脂。
汽车冲压件---英文名称
SUSP-ARM-FIX-REINF REAR-FRONT-SUBFRAME-ATTACH-BRKT-LH REAR-FRONT-SUBFRAME-ATTACH-BRKT-RH REAR-BACK-SUBFRAME-ATTACH-BRACKET REAR-BACK-SUBFRAME-ATTACH-BRACKET ISO-FIX-BRACKET SUBFRAME-ATTACH-REINFORCEMENT-LH SUBFRAME-ATTACH-REINFORCEMENT-RH FRONT-RAIL-ATTACH-BRACKET-LH FRONT-RAIL-ATTACH-BRACKET-RH FRONT-BEAM-BUMPER FRONT-UPPER-CRASH-BOX-LH FRONT-UPPER-CRASH-BOX-RH FRONT-LOWER-CRASH-BOX-LH FRONT-LOWER-CRASH-BOX-RH REAR-RAIL-ATTACH-BRACKET FRONT-TOW-HOOK-BRACKET REAR-UPPER-CRASH-BOX-LH REAR-UPPER-CRASH-BOX-RH REAR-LOWER-CRASH-BOX-LH REAR-LOWER-CRASH-BOX-RH GEARBOX-LEVER-FIX-BRACKET FRONT-HANDBRAKE-FIX-BRACKET CENTRAL-FUEL-TANK-REINF REAR-RAIL-CROSSMEMBER FRONT-RAIL-EXTENSION-LOWER-BRKT FRONT-RAIL-EXTENSION-LOWER-BRKT-RH
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
汽车冲压件中英对照表
BAR FR END UPR 散热器上横梁BEAM RR BPR INR 后保防撞梁内板BEAM RR BPR OTR 后保防撞梁外板BRACE RR SHELF LH 后行李箱隔板左侧支柱BRACE RR SHELF RH 后行李箱隔板右侧支柱BRACE RR. FLOOR SIDE LH 后地板左边支柱BRACE RR. FLOOR SIDE RH 后地板右边支柱BRACE S/MBR TO FRT FLOOR LH 前纵梁与前地板左连接板BRACKET HOOD RELEASE (LHD) 发罩拉索支架BRACKET RR FLOOR SEAT MTG LH 左后座椅安装支架BRACKET RR FLOOR SEAT MTG RH 右后座椅安装支架BRK S-IMPACT RR FR DR LH 前门防撞杆后支架BRKT ANTI ZIPPER LH 前地板与门槛内板左连接板BRKT BUMPER 前保险杠支架BRKT CTR BPR MTG 后保险杠中部支架BRKT FASCIA MTG 保险杠安装支架BRKT FENDER LWR LH 左侧前轮挡泥板下部支架BRKT FENDER LWR RH 右侧前轮挡泥板下部支架BRKT FENDER UPR LH 左侧前轮挡泥板上部支架BRKT FENDER UPR RH 左侧前轮挡泥板上部支架BRKT FOOT REST (LHD) 踏脚板支架BRKT GLS GUIDE DOOR 玻璃导轨支架BRKT S-IMPACT CTR FR DR 前门防撞杆中支架BRKT S-IMPACT FR FR DR LH 前门防撞杆前支撑板BRKT S-IMPACT FR FR DR RH 前门防撞杆前支撑板BRKT S-IMPACT FR RR DR LH 左后门侧防撞杆前支架BRKT STRIKER 背门锁扣加强板BRKT SUPT S-IMPACT RR DR LH 左后门侧防撞杆支架BRKT SUPT S-IMPACT RR DR RH 右后门侧防撞杆支架BRKT UPR BUMPER MTG 保险杠安装上支架BRKT ENG MOUNT 发动机悬置支架BRKT SPRING HOUSE RH 右前悬挂上支座BRKT FUEL TANK COMMON 油箱安装左后支架BRKT TRAILING ARM INR LH 左后悬挂纵臂安装内支架BRKT TRAILING ARM INR RH 右后悬挂纵臂安装内支架BRKT TRAILING ARM OTR LH 左后悬挂纵臂外支架BRKT TRAILING ARM OTR RH 右后悬挂纵臂外支架BULKHEAD HINGE FRT LWR LH 左侧前门下部铰链加强板隔板BULKHEAD HINGE FRT LWR RH 右侧前门下部铰链加强板隔板BULKHEAD R/FLR S/MBR LH 后地板左纵梁隔板BULKHEAD R/FLR S/MBR RH 后地板右纵梁隔板BULKHEAD SILL 门槛隔板C/MBR BACKBONE 中央通道横梁C/MBR FR END OTR 散热器下横梁外板C/MBR R/FLR 后地板中横梁C/MBR R/SEAT 后地板前横梁下板C/MBR F/FLR LH 前地板左前横梁C/MBR F/FLR RH 前地板右前横梁C/MBR F/FLR RR LH 前地板左后横梁C/MBR FR END, INR CTR 散热器下横梁中内板C/MBR FR END, INR LH 散热器下横梁左内板CHNL GLS GUIDE FR FR DR LH 左前门玻璃导轨CHNL GLS GUIDE FR FR DR RH 右前门玻璃导轨CHNL GLS GUIDE FR RR DR LH 左后门玻璃导轨CHNL GLS GUIDE FR RR DR RH 右后门玻璃导轨CHNL GLS GUIDE RR FR DR RH 右前门后玻璃导轨CHNL GLS GUIDE UPR RR DR LH 左后门上玻璃导轨CHNL GLS GUIDE UPR RR DR RH 右后门上玻璃导轨EXT DASH PANEL LH 前围挡板左下板EXT DASH PANEL RH 前围挡板右下板EXT C/MBR R/FLR LH 后地板中横梁与纵梁左连接板FRAME FR UPR INR LH 左翼子板加强梁内板FRAME FR UPR INR RH 右翼子板加强梁内板FRAME FR UPR OTR LH 左侧翼子板上部边梁外板FRAME FR UPR OTR RH 右侧翼子板上部边梁外板FRONT S/MBR REAR LH 左前纵梁与地板纵梁连接板FRONT, S/MBR REAR RH 右前纵梁与地板纵梁连接板HINGE FUEL FILLER DR 加油口盖铰链HOOK, MUFFLER B/BONE 中央通道消音器挂钩PANEL A PILLAR LWR LH 左A柱下板PANEL A PILLAR LWR RH 右A柱下板PANEL AIR EXTRACTION BOX OTR LH 左侧排气盒外板PANEL AIR EXTRACTION BOX OTR RH 右侧排气盒外板PANEL B PILLAR INNER LH 左侧B柱盖板PANEL B PILLAR INNER LH 左侧B柱内板PANEL B PILLAR INNER RH 右侧B柱盖板PANEL B PILLAR INNER RH 右侧B柱内板PANEL BODY SIDE OTR LH 左侧围外板PANEL BODY SIDE OTR RH 右侧围外板PANEL CANTRAIL INNER LH 左侧上边梁内板PANEL CANTRAIL INNER RH 右侧上边梁内板PANEL COWL TOP INR (LHD) 空气盒内板PANEL EXT REAR FLR FRT 后地板前连接板PANEL EXT REAR FLR RR 后地板后加强板PANEL FRONT FENDER LH 左前翼子板PANEL FRONT FENDER RH 右前翼子板PANEL FRT HEADER LWR 顶盖前横梁下部板PANEL PILLAR FR INR LH 左A柱内板PANEL PILLAR FR INR LH 左侧A柱内板PANEL PILLAR FR INR RH 右A柱内板PANEL PILLAR FR INR RH 右侧A柱内板 PANEL REAR FLOOR 后地板PANEL REAR SHELF 行李架隔板PANEL REINF FRT HINGE A PILLAR LH 左侧A柱铰链加强板PANEL REINF FRT HINGE A PILLAR RH 右侧A柱铰链加强板PANEL ROOF 顶盖PANEL ROOF BOW 顶盖中横梁PANEL RR END INR 后围内板PANEL RR END OTR 后围横梁外板PANEL RR HEADER UPR 顶盖后横梁上板PANEL RR QTR INR LWR LH 左后轮罩外板下段PANEL RR QTR INR LWR RH 右后轮罩外板下段PANEL RR QTR INR UPR LH 左后轮罩外板上段PANEL RR QTR INR UPR RH 右后轮罩外板上段PANEL RR. W/HSE INR LH 左轮罩内板PANEL RR. W/HSE INR RH 右轮罩内板PANEL SILL INR LH 前地板左门槛内板PANEL SILL INR LH 左门槛内板PANEL SILL INR RH 前地板右门槛内板PANEL SILL INR RH 右门槛内板PANEL SPRING HOUSE LH 左前悬挂支座下板PANEL SPRING HOUSE RH 右前悬挂支座下板PANEL COWL TOP OTR 空气盒外板PANEL DASH (LHD) 前围挡板PNL FR DR INR LH 左前门内板PNL FR DR INR RH 右前门内板PNL FR DR OTR LH 左前门外板PNL FR DR OTR RH 右前门外板PNL FUEL FILLER DR 加油口盖外板PNL HOOD INR 发罩内板PNL HOOD OTR 发罩外板PNL RR DR INR LH 左后门内板PNL RR DR INR RH 右后门内板PNL RR DR OTR LH左后门外板PNL RR DR OTR RH 右后门外板PNL T-GATE INR 后背门内板PNL T-GATE OTR 后背门外板PNL TRUNK LID INR 行李箱盖内板PNL TRUNK LID OTR 行李箱盖外板PNL SPRING HOUSE LH 左后悬挂支座下板PNL SPRING HOUSE RH 右后悬挂支座下板REINF A PILLAR UPR LH 左侧A柱上部加强板REINF A PILLAR UPR RH 右侧A柱上部加强板REINF B PILLAR CTR LH 左B柱中加强板REINF B PILLAR CTR RH 右B柱中加强板REINF B PILLAR DOUBLER LH 左侧B柱铰链加强板REINF B PILLAR DOUBLER RH 右侧B柱铰链加强板REINF B PILLAR LH 左侧B柱加强板REINF B PILLAR RH 右侧B柱加强板REINF B PILLAR UPR LH 左侧B柱加强上段REINF B PILLAR UPR RH 右侧B柱加强上段REINF BRACE REAR SHELF LH 行李箱隔板左托架支柱REINF BUMP STOP RH 右侧缓冲器加强板REINF BUMPER STAY LH 后保险杠左缓冲支柱加强板REINF BUMPER STAY RH 后保险杠右缓冲支柱加强板REINF COWL TOP INR (LHD) 转向柱加强板REINF DASH PANEL CTR 前围挡板下加强板REINF DOOR CHECK LH 左侧前门限位器加强板REINF FR END C/MBR SIDE LH 散热器下横梁左侧加强板REINF FRAME UPR FR DR LH 左前门窗框加强板REINF FRAME UPR FR DR RH 右后门窗框加强板REINF FRAME UPR FR DR RH 右前门窗框加强板REINF FRAME UPR RR DR LH 左后门窗框加强板REINF FUEL FILLER DR 加油口盖加强板REINF HINGE FRT UPR LH 左侧前门上部铰链加强板REINF HINGE FRT UPR RH 右侧前门上部铰链加强板REINF HINGE RR DR LH 左后门铰链加强板REINF HINGE RR DR RH 右后门铰链加强板REINF HINGE T-LID LH 行李箱盖铰链左加强板REINF HINGE T-LID RH 行李箱盖铰链右加强板REINF HOOD HINGE LH 发动机罩左侧铰链加强板REINF LATCH FR DR LH 左前门锁加强板REINF LATCH FR DR RH 右前门锁加强板REINF LATCH RR DR RH 右后门锁加强板REINF REAR SHELF FRONT 行李架前加强板REINF SBELT SIDE LH 左前座安全带左下加强板REINF SBELT SIDE RH 左前座安全带左下加强板REINF SILL LH 左侧门槛加强板REINF SILL RH 右侧门槛加强板REINF STG COL BRKT (LHD) 转向柱支架REINF WAIST OTR RR DR RH 右后门窗沿外加强板REINF BACKBONE 中央通道加强板REINF ENG MOUNT 发动机悬置加强板REINF FR END C/MBR 散热器下横梁加强板REINF FR S/MBR INR, FR LH 左前纵梁内板前加强板REINF FR S/MBR INR, FR RH 右前纵梁内板前加强板REINF FR S/MBR INR, RR LH 左前纵梁内板后加强板REINF FR S/MBR OTR LH 左前纵梁外板加强板REINF FR S/MBR OTR REAR LH 左前纵梁外板后加强板REINF FR S/MBR OTR REAR RH 右前纵梁外板后加强板REINF FRT S/MBR, REAR LH 左前纵梁地板纵梁加强板REINF T/M MOUNT 变速箱悬置加强板REINF DASH PANEL (LHD) 前围挡板内加强板REINF R/FLR LH 后地板左加强板REINF R/FLR RH 后地板右加强板REINF C/MBR UPR LH 后地板前横梁下板左加强板REINF C/MBR UPR RH 后地板前横梁下板右加强板REINF R/FLR S/MBR FR LH 后地板左纵梁加强板REINF R/FLR S/MBR FR RH 后地板右纵梁加强板REINF R/FLR S/MBR LH 后地板左纵梁侧加强板REINF R/FLR S/MBR RH 后地板右纵梁侧加强板REINF S/BELT R/FLR 后座椅安全带内加强板S/MBR FR FLR LH 前地板左纵梁S/MBR FR FLR RH 前地板右纵梁S/MBR FR INR LH 左前纵梁内板S/MBR FR INR RH 右前纵梁内板S/MBR FR OTR LH 左前纵梁外板S/MBR FR OTR RH 右前纵梁外板SHIELD FR FENDER LH 左前挡泥板SHIELD FR FENDER RH 右前挡泥板SMBR RR FLR LH 后地板左纵梁SMBR RR FLR RH 后地板右纵梁SUPT R/FLR S/MBR LH 后地板左纵梁支架。
冲压加工工序名称中英文对照表
冲压加工工序名称中英文对照表 序号工序名称英文全称略写 1 剪断 SH Shear SH 2 落料 BL Blank BL 3 引伸拉延 DR Draw DR 4 再引伸 RDR Redraw RDR 5 剪边 TR Trimming TR 6 冲孔 PI Piercing PI 或 PRC 7 成形 FO Form FO 8 整形 RST Restricting RST 9 弯边翻边FL Flange FL FL+RST 10 弯曲整形 FL+RST FlangeAND Restricting 11 落料、冲孔 BL+PI Blank AND Piercing BL+PI TR+PI 12 剪边、冲孔 TR+PI TrimmingAND Piercing 13 侧冲孔 CPI CAMPI或CAMPRC 14 侧剪边 CTR CTR 15 侧整形 CRST CRST 16 侧翻边 CFL CFL 17 翻孔 BUR Burring BUR 18 包边 HEM Hemming HEM 19 分割 SEP Separating SEP 20 辗制成形 RO-FO Roll-form RO-FO S.D.F 21 伸展抽制成形 S.D.F Stretch-draw forming
冲压件中英文对照表
右侧A柱上隔板DIAPHRAGM-"A"PILLAR UPR RH右前门内板加强板REINF-INNER,FRT DOOR,RH仪表板横梁左支架SUPPORT-TIE BAR LH左侧围外下板PANEL-SIDE OUTER LWR LH左侧A柱上隔板DIAPHRAGM-"A"PILLAR UPR LH油箱-上部FUEL TANK-UPPER HALF仪表斑横梁右侧安装支架SIDE SUPPORT-I.P.TO"A"PILLAR RH 后上板后横梁右支架SUPPORT-FRAME,BACK PNL UPR RR RH右侧A柱支撑加强板REINF-SUPPORT FRONT PILLAR RH油箱-下部FUEL TANK-LOWER HALF仪表板横梁左侧安装支架SIDE SUPPORT-I.P.TO"A"PILLAR LH 后上板后横梁左支架SUPPORT-FRAME,BACK PNL UPR RR LH左侧A柱支撑加强板REINF-SUPPORT FRONT PILLAR LHA柱加强板-右REINF-FRONT PILLAR RH右前纵梁内加强板REINF-LONGITUDINAL FR INR RH顶盖前横梁RAIL-WINDSHIELD HEADER右侧A柱内板PANEL-"A"PILLAR INNER RHA柱加强板-左REINF-FRONT PILLAR LH左前纵梁内加强板REINF-LONGITUDINAL FR INR LH顶盖中横梁SUPPORT-ROOF CENTER FRT左侧A柱内板PANEL-"A"PILLAR INNER LHA柱上加强板REINF-FRONT PILLAR UPR RH前纵梁隔板加强板REINF-SIDE CLOSURE顶盖后横梁FRAME-ROOF REAR右侧B柱加强板PANEL-"B"PILLAR,RHA柱上加强板REINF-FRONT PILLAR UPR LH右前纵梁隔板CLOSURE-LONGI.INTERM.RH顶盖PANEL-ROOF左侧B柱加强板PANEL-"B"PILLAR,LH右前门上铰链加强板REINF-FRT DOOR HINGE UPPER RH左前纵梁隔板CLOSURE-LONGI.INTERM.LH右侧围前下连接板PATCH-LOWER FRONT RH右侧围内板PANEL-SIDE INNER,RH左前门上铰链加强板REINF-FRT DOOR HINGE UPPER LH前隔板内板PANEL-DASH LOWER INNER左侧围前下连接板PATCH-LOWER FRONT LH左侧围内板PANEL-SIDE INNER,LH右前门下铰链加强板REINF-FR DOOR HINGE LOWER RH前隔板PANEL-BULKHEAD右侧围外板PANEL-SIDE,OTR RH天线安装支架BRKT-ANTENNA FIXING左前门下铰链加强板REINF-FR DOOR HINGE LOWER LH前隔板上盖板DASH PANEL TOP ASM左侧围外板PANEL-SIDE,OTR LH顶盖与右侧纵梁后结合面加强板REINF-JUNCTION,ROOF RAIL RH顶盖右侧纵梁RAIL-ROOF SIDE RH仪表板上板PANEL-DASH UPPER左前轮罩上纵梁连接板PATCH-LONGITUDINAL FR UPR LH顶盖与左侧纵梁后结合面加强板REINF-JUNCTION,ROOF RAIL LH顶盖左侧纵梁RAIL-ROOF SIDE LH前隔板上支架加强件BRKT-DASH UPR REINF.右前轮罩上纵梁连接板加强板REINF-INNER LONGITUDINAL FR UPR RH 右侧围后部内撑件GUSSETT-SIDE PANEL,RR INR,RH右B柱内板PANEL-"B"PILLAR INNER RH前隔板下连接板PATCH-DASH LWR CTR左前轮罩上纵梁连接板加强板REINF-INNER LONGITUDINAL FR UPR LH 左侧围后部内撑件GUSSETT-SIDE PANEL,RR INR,LH左B柱内板PANEL-"B"PILLAR INNER LH右侧前下纵梁LONGITUDINAL-INTERMEDIATE FR LWR RH右前轮罩后部内板PANEL-W/HOUSE REAR INNER RH右侧围后部外下板PANEL-SIDE OTR LWR RH右侧门铰链和座椅安全带加强板REINF-SEAT BELT AND DR HINGE RH 左侧前下纵梁LONGITUDINAL-INTERMEDIATE FR LWR LH左前轮罩后部内板PANEL-W/HOUSE REAR INNER LH左侧围后部外下板PANEL-SIDE OTR LWR LH左侧门铰链和座椅安全带加强板REINF-SEAT BELT AND DR HINGE LH 仪表板隔板PLATE-BULKHEAD,DASH PANEL右前轮罩前部内板PANEL-W/HOUSE FRONT INNER RH后上板右前支撑板SUPPORT-BACK PANEL UPR FRAME TO SIDE INR RH右侧门槛加强板REINF-ROCKER RH仪表板中心支架BRKT-CENTER INSTRUMENT PANEL左前轮罩前部内板PANEL-W/HOUSE FRONT INNER LH后上板左前支撑板SUPPORT-BACK PANEL UPR FRAME TO SIDE INR LH左侧门槛加强板REINF-ROCKER LH电喷ECU安装支架BRKT-INJECTION ECU MOUNTING右前纵梁LONGITUDINAL-FRONT RH右前座椅安全带加强件REINF-SEAT BELT FRONT RH右侧"A"柱内下板PANEL-FRT PLR INR LWR-RH地板通道前上加强板REINF-TUNNEL UPR FRONT左前纵梁LONGITUDINAL-FRONT LH左前座椅安全带加强件REINF-SEAT BELT FRONT LH左侧"A"柱内下板PANEL-FRT PLR INR LWR-LH转向管柱上支架BRKT-UPR STRG COLUMN右前部下纵梁LONGITUDINAL-FRONT LOWER RH后上板右连接板SUPPORT-REAR RH右后轮罩侧围加强板REINF-SIDE,W/HOUSE RH转向管柱下支架BRKT-LWR STEERING COLUMN左前部下纵梁LONGITUDINAL-FRONT LOWER LH后上板左连接板SUPPORT-REAR LH左后轮罩侧围加强板REINF-SIDE,W/HOUSE LH前地板PANEL-FRONT FLOOR右前纵梁加强板REINF-LONGITUDINAL RH右后门门闩加强件REINF-STRIKER,RR DOOR RH右前轮罩上纵梁LONGITUDINAL-FRONT UPPER RH地板右侧纵梁LONGITUDINAL-FLOOR CENTER RH SIDE左前纵梁加强板REINF-LONGITUDINAL LH左后门门闩加强件REINF-STRIKER,RR DOOR LH左前轮罩上纵梁LONGITUDINAL-FRONT UPPER LH地板左侧纵梁LONGITUDINAL-FLOOR CENTER LH SIDE前保险杠辅助支架BRKT-ATTACH FR BUMPER前后门闩固定件CAGE-STRIKER,FR&RR DOORS RH/LH右减振器定位板LOCATOR-S/ABS RH地板右侧围板PANEL-FLOOR SIDE RH发动机舱后上部右侧密封条支架PATCH-LONGTITUDINAL&DASH LWR RH 右尾灯后上板PANEL-TAIL LAMP REAR UPR RH左减振器定位板LOCATOR-S/ABS LH地板左侧围板PANEL-FLOOR SIDE LH发动机舱后上部左侧密封条支架PATCH-LONGTITUDINAL&DASH LWR LH 左尾灯后上板PANEL-TAIL LAMP REAR UPR LH右前轮罩板PANEL-W/HOUSE FRONT REAR RH地板通道上加强件REINF-TUNNEL UPR REAR发动机右侧安装上支座BRKT-ENGINE MOUNT UPPER RH右C柱加强件REINF-"C"PILLAR RH左前轮罩板PANEL-W/HOUSE FRONT REAR LH前座椅前横梁C/MBR-FRONT SEAT FRONT右后纵梁LONGITUDINAL-REAR RH左C柱加强件REINF-"C"PILLAR LH安装仪横梁右侧安装支架BRACKET-SIDE,FIX I.P.RH右前座椅后横梁C/MBR-FRONT SEAT REAR RH左后纵梁LONGITUDINAL-REAR LH燃油加注口支架BRKT-ACTUATOR FUEL FILLER仪表板横梁左侧安装支架BRACKET-SIDE,FIX I.P.LH左前座椅后横梁C/MBR-FRONT SEAT REAR LH座椅安全带加强板REINF-SEAT BELT行李箱内饰支架BRKT-TRIM,TRUNK右前轮罩上纵梁连接板PATCH-LONGITUDINAL FR UPR RH前座椅后安装点内加强板REINF-INR.RR C/MBR FR SEAT SUPPORT右后纵梁侧围板PANEL-SIDE，RR LONGITUDINAL RH右后轮罩内加强板PATCH-W/HOUSE INNER RH左后轮罩内板W/HOUSE-REAR INNER LH右前座椅后横梁外加强板REINF-OTR.RR C/MBR FR SEAT SUPPORT RH 左后纵梁侧围板PANEL-SIDE，RR LONGITUDINAL LH左后轮罩内加强板PATCH-W/HOUSE INNER LH右后轮罩内连接板EXTENSION-W/HOUSE INNER RH左前座椅后横梁外加强板REINF-OTR.RR C/MBR FR SEAT SUPPORT LH座椅加强板REINF-FRONT SEAT右后轮罩内板W/HOUSE-REAR INNER RH左后轮罩内连接板EXTENSION-W/HOUSE INNER LH座椅安全带固定支座加强板REINF-SEAT BELT ANCHOR悬架安装导套加强板REINF-THREADED GUIDE后悬架左前右后安装加强件REINF-FIX REAR SUSPENSION LH FRT/RH RR 燃油加注口FUEL FILLER中地板PANEL-REAR FLOOR FRONT右后纵梁加强件REINF-LONGITUDINAL RH右侧前密封条安装支架BRKT-SEAL RETENTION RH右侧尾灯灯罩板PANEL-TAIL LAMP HSG RH后地板PANEL-REAR FLOOR REAR左后纵梁加强件REINF-LONGITUDINAL LH左侧前密封条安装支架BRKT-SEAL RETENTION LH左侧尾灯灯罩板PANEL-TAIL LAMP HSG LH后地板前横梁C/MBR-REAR FLOOR CENTER后桥右侧安装支架BRKT-REAR AXLE INR RH右侧前翼子板FENDER-RH后保险杠右安装板PANEL-REAR BUMPER LWR RH中地板前横梁C/MBR-REAR FLOOR FRONT后桥左侧安装支架BRKT-REAR AXLE INR LH左侧前翼子板FENDER-LH后保险杠左安装板PANEL-REAR BUMPER LWR LH排气管支架加强板REINF-BRKT EXHAUST TUBE隔热板支架BRKT-HEAT SHIRLD右前翼子板后连接板PATCH-FRONT FENDER RR RH后座背板横梁右支架SUPPORT-C/MBR REAR SEAT BACK RH右前门外板PANEL-OTR,FRONT DOOR,RH右后纵梁内加强板REINF-INNER,LONGITUDINAL RH左前翼子板后连接板PATCH-FRONT FENDER RR LH后座背板横梁左支架SUPPORT-C/MBR REAR SEAT BACK LH左前门外板PANEL-OTR,FRONT DOOR,LH左后纵梁内加强板REINF-INNER,LONGITUDINAL LH水箱横梁右支架SUPPORT-C/MBR RAD,OTR RH右后减振器支架SUPPORT-SHOCK ABSORBER RH右前门外加强板REINF-OUTER,FRT DOOR,RH后保险杠右侧加强件REINF-REAR BUMPER RH水箱横梁左支架SUPPORT-C/MBR RAD,OTR LH左后减振器支架SUPPORT-SHOCK ABSORBER LH左前门外加强板REINF-OUTER,FRT DOOR,LH后保险杠左侧加强件REINF-REAR BUMPER LH发动机舱前部上横梁PANEL-FRONT,UPPER减振器支架加强板REINF-SUPPORT S/ABSORBER RH/LH前门内把手安装支架BRKT-FIX HANDLE,FRONT DOOR后驻车固定点BRKT-VEHICLE ANCHORAGE发动机舱前部右立柱SUPPORT-FRT PNL SIDE RH前保险杠支架BRKT-FRONT BUMPER右后门内板PANEL-INNER,REAR DOOR,RH纵梁制动管支架BRKT-BRAKE TUBES ON LONGITUDINAL发动机舱前部左立柱SUPPORT-FRT PNL SIDE LH发动机前下纵梁加强板REINF-FR LONGIT UNDER ENGINE左后门内板PANEL-INNER,REAR DOOR,LH右后座椅安全带加强板REINF-LATERAL SEAT BELT RH水箱后横梁C/MBR-RAD,RR发动机盖右侧铰链加强板REINF-HOOD HINGE RH右后门内板加强板REINF-INNER,RR DOOR,RH左后座椅安全带加强板REINF-LATERAL SEAT BELT LH水箱前横梁C/MBR-RAD,FRT发动机盖左侧铰链加强板REINF-HOOD HINGE LH左后门内板加强板REINF-INNER,RR DOOR,LH右侧推力杆安装支架REINF-BRKT RR AXLE RH发动机舱前部中立柱SUPPORT-FRT PNL,CTR发动机盖铰链安装板PLATE-HOOD HINGE右后门铰链立柱板PILLAR-HINGE,REAR DOOR,RH左侧推力杆安装支架REINF-BRKT RR AXLE LH水箱横梁右侧支架SUPPORT-C/MEMBER RAD INR RH发动机仓前部右侧上连接板PANEL-FRONT,UPPER RH左后门铰链立柱板PILLAR-HINGE,REAR DOOR,LH后上板PANEL-BACK UPPER水箱横梁左侧支架SUPPORT-C/MEMBER RAD INR LH发动机仓前部左侧上连接板PANEL-FRONT,UPPER LH玻璃导轨支架BRKT-RAIL,GLASS GUIDE后隔板PANEL-RR SEAT RR左前轮罩延伸板W/HOUSE EXTENSION-FRONT LH右前伸轮罩板PANEL-W/HOUSE EXTENSION FRONT RH右后门门闩加强板REINF-LATCH,DOOR,RH后上板后横梁FRAME-BACK PNL UPR RR发动机左侧下安装支架加强板REINF BRKT-ENGINE MTG LOWER LH 左前伸轮罩板PANEL-W/HOUSE EXTENSION FRONT LH左后门门闩加强板REINF-LATCH,DOOR,LH后上板前横梁FRAME-BACK PANEL UPR FRT发动机右侧下安装支架BRKT-ENGINE MOUNT LOWER RH右前轮罩延伸板W/HOUSE EXTENSION-FRONT RH右后门外板PANEL-OUTER,REAR DOOR,RH后部下围板PANEL-BACK LWR发动机左侧下安装支架（左）BRKT-ENGINE MTG LWR LH后悬架左后右前安装加强件REINF-FIX REAR SUSPENSION LH RR/RH FRT 左后门外板PANEL-OUTER,REAR DOOR,LH后部下围板加强件REINF BACK PANEL LWR仪表板横梁右支架SUPPORT-TIE BAR RH右侧围外下板PANEL-SIDE OUTER LWR RH右后门外板加强板REINF-OUTER,REAR DOOR,RH右侧尾灯灯座加强板REINF PANEL-TAIL LAMP HSG RH左前门门闩加强板REINF-LATCH,FRONT DOOR,LH左右行李箱铰链加强板REINF-HINGE,TRUNK,LH左后门外板加强板REINF-OUTER,REAR DOOR,LH左侧尾灯灯座加强板REINF PANEL-TAIL LAMP HSG LH盖板右侧铰链加强板REINF-HINGE,HOOD,RH行李箱铰链安装板SPACER-HINGE,MOBILE,TRUNK后门内把手安装支架BRKT-FIX HANDLE,DOOR行李箱锁钩加强板REINF-LATCH盖板左侧铰链加强板REINF-HINGE,HOOD,LH行李箱安装铰链加强板REINF-FIXED HINGE,TRUNK后门三角窗玻璃下支架SUPPORT-FIXED GLASS LWR后围右侧支撑板SUPPORT-REAR BULKHEAD RH气弹簧支架BRKT-GAS SPRING盖板内板PANEL-INNER HOOD行李箱内板PANEL-INNER TRUNK后围左侧支撑板SUPPORT-REAR BULKHEAD LH盖板闩眼加强板REINF-STRIKER,HOOD盖板外板PANEL-OUTER HOOD行李箱隔板PANEL-CLOSUIE TRUNK备胎螺栓支架SUPPORT-BOLT,SPARE WHEEL带天窗的顶盖PANAL-ROOF OUTER，OPENING ROOF左前门铰链立柱板PILLAR-HINGE,FRT DOOR,LH行李箱盖闩加强板REINF-LATCH TRUNK LID空调与仪表板连接左支架BRKT-FIX HVAC TO PANEL DASH UPPER LH天窗骨架FRAME-SUN ROOF HOUSING右前门门闩加强板REINF-LATCH,FRONT DOOR,RH行李箱上部外板PANEL-OUTER TRUNK UPPER空调与仪表板连接右支架BRKT-FIX HVAC TO PANEL DASH UPPER RH右侧座椅安全带加强板REINF-SEAT BELT RH右前门铰链立柱板PILLAR-HINGE,FRT DOOR,RH行李箱下部外板PANEL-OUTER TRUNK LOWER右前门内板PANEL-INNER,FRONT DOOR,RH左侧座椅安全带加强板REINF-SEAT BELT LH左前门内板加强板REINF-INNER,FRT DOOR,LH左右行李箱铰链加强板REINF-HINGE,TRUNK,RH左前门内板PANEL-INNER,FRONT DOOR,LH欢迎您的下载，资料仅供参考！致力为企业和个人提供合同协议，策划案计划书，学习资料等等打造全网一站式需求。
汽车冲压部件中英对照表
英文名称 INSTALL ASSY PANEL PILLAR DOOR HOOD stringer mennber Cross mennber BRACE BRACKET HINGE BULKHEAD REINF FLOOR lower LH RH Front Rear inner FR DR RR DR F/FLR R/FLR BAR S-IMPACT RR DR BAR FR END UPR BEAM RR BPR INR BEAM RR BPR OTR BRACE RR SHELF LH BRACE RR SHELF RH BRACE RR. FLOOR SIDE LH BRACE RR. FLOOR SIDE RH BRACE S/MBR TO FRT FLOOR LH BRACKET HOOD RELEASE (LHD) BRACKET RR FLOOR SEAT MTG LH BRACKET RR FLOOR SEAT MTG RH BRK S-IMPACT RR FR DR LH BRKT ANTI ZIPPER LH BRKT BUMPER BRKT CTR BPR MTG BRKT FASCIA MTG BRKT FENDER LWR LH 缩写 中文名称 安装 总成 板 柱 门 盖 纵梁 横梁 支柱 支架 铰链 隔板 加强板 地板 上部 下部 左侧 右侧 前侧 后侧 外侧 内侧 前门 后门 前地板 后地板 后门侧防撞杆 散热器上横梁 后保防撞梁内板 后保防撞梁外板 后行李箱隔板左侧支柱 后行李箱隔板右侧支柱 后地板左边支柱 后地板右边支柱 前纵梁与前地板左连接板 发罩拉索支架 左后座椅安装支架 右后座椅安装支架 前门防撞杆后支架 前地板与门槛内板左连接板 前保险杠支架 后保险杠中部支架 保险杠安装支架 左侧前轮挡泥板下部支架
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
汽车冲压件中英文名称对照表汽车冲压件中英文名称对照表.txt都是一个山的狐狸，你跟我讲什么聊斋，站在离你最近的地方，眺望你对别人的微笑，即使心是百般的疼痛只为把你的一举一动尽收眼底．刺眼的白色，让我明白什么是纯粹的伤害。
[原创] 汽车冲压件中英文名称对照表英文名称中文名称INSTALL 安装ASSY 总成PANEL PNL 板PILLAR 柱DOOR DR 门HOOD 盖S/MBR 纵梁C/MBR 横梁BRACE 支柱BRACKET BRKT 支架HINGE 铰链BULKHEAD 隔板REINF 加强板FLOOR 地板UPR 上部LWR 下部LH 左侧RH 右侧FR 前侧RR 后侧OTR 外侧INR 内侧FR DR 前门RR DR 后门F/FLR 前地板R/FLR 后地板BAR S-IMPACT RR DR 后门侧防撞杆BAR FR END UPR 散热器上横梁BEAM RR BPR INR 后保防撞梁内板BEAM RR BPR OTR 后保防撞梁外板BRACE RR SHELF LH 后行李箱隔板左侧支柱BRACE RR SHELF RH 后行李箱隔板右侧支柱BRACE RR. FLOOR SIDE LH 后地板左边支柱BRACE RR. FLOOR SIDE RH 后地板右边支柱BRACE S/MBR TO FRT FLOOR LH 前纵梁与前地板左连接板BRACKET HOOD RELEASE (LHD) 发罩拉索支架BRACKET RR FLOOR SEAT MTG LH 左后座椅安装支架BRACKET RR FLOOR SEAT MTG RH 右后座椅安装支架BRK S-IMPACT RR FR DR LH 前门防撞杆后支架BRKT ANTI ZIPPER LH 前地板与门槛内板左连接板BRKT BUMPER 前保险杠支架BRKT CTR BPR MTG 后保险杠中部支架BRKT FASCIA MTG 保险杠安装支架BRKT FENDER LWR LH 左侧前轮挡泥板下部支架BRKT FENDER LWR RH 右侧前轮挡泥板下部支架BRKT FENDER UPR LH 左侧前轮挡泥板上部支架BRKT FENDER UPR RH 右侧前轮挡泥板上部支架BRKT FOOT REST (LHD) 踏脚板支架BRKT GLS GUIDE DOOR 玻璃导轨支架BRKT S-IMPACT CTR FR DR 前门防撞杆中支架BRKT S-IMPACT FR FR DR LH 前门防撞杆前支撑板BRKT S-IMPACT FR FR DR RH 前门防撞杆前支撑板BRKT S-IMPACT FR RR DR LH 左后门侧防撞杆前支架BRKT STRIKER 背门锁扣加强板BRKT SUPT S-IMPACT RR DR LH 左后门侧防撞杆支架BRKT SUPT S-IMPACT RR DR RH 右后门侧防撞杆支架BRKT UPR BUMPER MTG 保险杠安装上支架BRKT ENG MOUNT 发动机悬置支架BRKT SPRING HOUSE RH 右前悬挂上支座BRKT FUEL TANK COMMON 油箱安装左后支架BRKT TRAILING ARM INR LH 左后悬挂纵臂安装内支架BRKT TRAILING ARM INR RH 右后悬挂纵臂安装内支架BRKT TRAILING ARM OTR LH 左后悬挂纵臂外支架BRKT TRAILING ARM OTR RH 右后悬挂纵臂外支架BULKHEAD HINGE FRT LWR LH 左侧前门下部铰链加强板隔板BULKHEAD HINGE FRT LWR RH 右侧前门下部铰链加强板隔板BULKHEAD R/FLR S/MBR LH 后地板左纵梁隔板BULKHEAD R/FLR S/MBR RH 后地板右纵梁隔板BULKHEAD SILL 门槛隔板C/MBR BACKBONE 中央通道横梁C/MBR FR END OTR 散热器下横梁外板C/MBR R/FLR 后地板中横梁C/MBR R/SEAT 后地板前横梁下板C/MBR F/FLR LH 前地板左前横梁C/MBR F/FLR RH 前地板右前横梁C/MBR F/FLR RR LH 前地板左后横梁C/MBR FR END, INR CTR 散热器下横梁中内板C/MBR FR END, INR LH 散热器下横梁左内板CHNL GLS GUIDE FR FR DR LH 左前门玻璃导轨CHNL GLS GUIDE FR FR DR RH 右前门玻璃导轨CHNL GLS GUIDE FR RR DR LH 左后门玻璃导轨CHNL GLS GUIDE FR RR DR RH 右后门玻璃导轨CHNL GLS GUIDE RR FR DR RH 右前门后玻璃导轨CHNL GLS GUIDE UPR RR DR LH 左后门上玻璃导轨CHNL GLS GUIDE UPR RR DR RH 右后门上玻璃导轨EXT DASH PANEL LH 前围挡板左下板EXT DASH PANEL RH 前围挡板右下板EXT C/MBR R/FLR LH 后地板中横梁与纵梁左连接板FRAME FR UPR INR LH 左翼子板加强梁内板FRAME FR UPR INR RH 右翼子板加强梁内板FRAME FR UPR OTR LH 左侧翼子板上部边梁外板FRAME FR UPR OTR RH 右侧翼子板上部边梁外板FRONT S/MBR REAR LH 左前纵梁与地板纵梁连接板FRONT, S/MBR REAR RH 右前纵梁与地板纵梁连接板HINGE FUEL FILLER DR 加油口盖铰链HOOK, MUFFLER B/BONE 中央通道消音器挂钩PANEL A PILLAR LWR LH 左A柱下板PANEL A PILLAR LWR RH 右A柱下板PANEL AIR EXTRACTION BOX OTR LH 左侧排气盒外板PANEL AIR EXTRACTION BOX OTR RH 右侧排气盒外板PANEL B PILLAR INNER LH 左侧B柱盖板PANEL B PILLAR INNER LH 左侧B柱内板PANEL B PILLAR INNER RH 右侧B柱盖板PANEL B PILLAR INNER RH 右侧B柱内板PANEL BODY SIDE OTR LH 左侧围外板PANEL BODY SIDE OTR RH 右侧围外板PANEL CANTRAIL INNER LH 左侧上边梁内板PANEL CANTRAIL INNER RH 右侧上边梁内板PANEL COWL TOP INR (LHD) 空气盒内板PANEL EXT REAR FLR FRT 后地板前连接板PANEL EXT REAR FLR RR 后地板后加强板PANEL FRONT FENDER LH 左前翼子板PANEL FRONT FENDER RH 右前翼子板PANEL FRT HEADER LWR 顶盖前横梁下部板PANEL PILLAR FR INR LH 左A柱内板PANEL PILLAR FR INR LH 左侧A柱内板PANEL PILLAR FR INR RH 右A柱内板PANEL PILLAR FR INR RH 右侧A柱内板PANEL REAR FLOOR 后地板PANEL REAR SHELF行李架隔板PANEL REINF FRT HINGE A PILLAR LH 左侧A柱铰链加强板PANEL REINF FRT HINGE A PILLAR RH 右侧A柱铰链加强板PANEL ROOF 顶盖PANEL ROOF BOW 顶盖中横梁PANEL RR END INR 后围内板PANEL RR END OTR 后围横梁外板PANEL RR HEADER UPR 顶盖后横梁上板PANEL RR QTR INR LWR LH 左后轮罩外板下段PANEL RR QTR INR LWR RH 右后轮罩外板下段PANEL RR QTR INR UPR LH 左后轮罩外板上段PANEL RR QTR INR UPR RH 右后轮罩外板上段PANEL RR. W/HSE INR LH 左轮罩内板PANEL RR. W/HSE INR RH 右轮罩内板PANEL SILL INR LH 前地板左门槛内板PANEL SILL INR LH 左门槛内板PANEL SILL INR RH 前地板右门槛内板PANEL SILL INR RH 右门槛内板PANEL SPRING HOUSE LH 左前悬挂支座下板PANEL SPRING HOUSE RH 右前悬挂支座下板PANEL COWL TOP OTR 空气盒外板PANEL DASH (LHD) 前围挡板PNL FR DR INR LH 左前门内板PNL FR DR INR RH 右前门内板PNL FR DR OTR LH 左前门外板PNL FR DR OTR RH 右前门外板PNL FUEL FILLER DR 加油口盖外板PNL HOOD INR 发罩内板PNL HOOD OTR 发罩外板PNL RR DR INR LH 左后门内板PNL RR DR INR RH 右后门内板PNL RR DR OTR LH 左后门外板PNL RR DR OTR RH 右后门外板PNL T-GATE INR 后背门内板PNL T-GATE OTR 后背门外板PNL TRUNK LID INR 行李箱盖内板PNL TRUNK LID OTR 行李箱盖外板PNL SPRING HOUSE LH 左后悬挂支座下板PNL SPRING HOUSE RH 右后悬挂支座下板REINF A PILLAR UPR LH 左侧A柱上部加强板REINF A PILLAR UPR RH 右侧A柱上部加强板REINF B PILLAR CTR LH 左B柱中加强板REINF B PILLAR CTR RH 右B柱中加强板REINF B PILLAR DOUBLER LH 左侧B柱铰链加强板REINF B PILLAR DOUBLER RH 右侧B柱铰链加强板REINF B PILLAR LH 左侧B柱加强板REINF B PILLAR RH 右侧B柱加强板REINF B PILLAR UPR LH 左侧B柱加强上段REINF B PILLAR UPR RH 右侧B柱加强上段REINF BRACE REAR SHELF LH 行李箱隔板左托架支柱REINF BUMP STOP RH 右侧缓冲器加强板REINF BUMPER STAY LH 后保险杠左缓冲支柱加强板REINF BUMPER STAY RH 后保险杠右缓冲支柱加强板REINF COWL TOP INR (LHD) 转向柱加强板REINF DASH PANEL CTR 前围挡板下加强板REINF DOOR CHECK LH 左侧前门限位器加强板REINF FR END C/MBR SIDE LH 散热器下横梁左侧加强板REINF FRAME UPR FR DR LH 左前门窗框加强板REINF FRAME UPR FR DR RH 右后门窗框加强板REINF FRAME UPR FR DR RH 右前门窗框加强板REINF FRAME UPR RR DR LH 左后门窗框加强板REINF FUEL FILLER DR 加油口盖加强板REINF HINGE FRT UPR LH 左侧前门上部铰链加强板REINF HINGE FRT UPR RH 右侧前门上部铰链加强板REINF HINGE RR DR LH 左后门铰链加强板REINF HINGE RR DR RH 右后门铰链加强板REINF HINGE T-LID LH 行李箱盖铰链左加强板REINF HINGE T-LID RH 行李箱盖铰链右加强板REINF HOOD HINGE LH 发动机罩左侧铰链加强板REINF LATCH FR DR LH 左前门锁加强板REINF LATCH FR DR RH 右前门锁加强板REINF LATCH RR DR RH 右后门锁加强板REINF REAR SHELF FRONT 行李架前加强板REINF SBELT SIDE LH 左前座安全带左下加强板REINF SBELT SIDE RH 左前座安全带左下加强板REINF SILL LH 左侧门槛加强板REINF SILL RH 右侧门槛加强板REINF STG COL BRKT (LHD) 转向柱支架REINF WAIST OTR RR DR RH 右后门窗沿外加强板REINF BACKBONE 中央通道加强板REINF ENG MOUNT 发动机悬置加强板REINF FR END C/MBR 散热器下横梁加强板REINF FR S/MBR INR, FR LH 左前纵梁内板前加强板REINF FR S/MBR INR, FR RH 右前纵梁内板前加强板REINF FR S/MBR INR, RR LH 左前纵梁内板后加强板REINF FR S/MBR OTR LH 左前纵梁外板加强板REINF FR S/MBR OTR REAR LH 左前纵梁外板后加强板REINF FR S/MBR OTR REAR RH 右前纵梁外板后加强板REINF FRT S/MBR, REAR LH 左前纵梁地板纵梁加强板REINF T/M MOUNT 变速箱悬置加强板REINF DASH PANEL (LHD) 前围挡板内加强板REINF R/FLR LH 后地板左加强板REINF R/FLR RH 后地板右加强板REINF C/MBR UPR LH 后地板前横梁下板左加强板REINF C/MBR UPR RH 后地板前横梁下板右加强板REINF R/FLR S/MBR FR LH 后地板左纵梁加强板REINF R/FLR S/MBR FR RH 后地板右纵梁加强板REINF R/FLR S/MBR LH 后地板左纵梁侧加强板REINF R/FLR S/MBR RH 后地板右纵梁侧加强板REINF S/BELT R/FLR 后座椅安全带内加强板S/MBR FR FLR LH 前地板左纵梁S/MBR FR FLR RH 前地板右纵梁S/MBR FR INR LH 左前纵梁内板S/MBR FR INR RH 右前纵梁内板S/MBR FR OTR LH 左前纵梁外板S/MBR FR OTR RH 右前纵梁外板SHIELD FR FENDER LH 左前挡泥板SHIELD FR FENDER RH 右前挡泥板SMBR RR FLR LH 后地板左纵梁SMBR RR FLR RH 后地板右纵梁SUPT R/FLR S/MBR LH 后地板左纵梁支架。