AZ P4620 Photoresist
AZ P4620•@ Lithography performance
Process Conditions:
Optitrac Coat/ Bake Coat: Static dispense on Silicon Target Film Thickness: 24 µm Softbake: 1st layer 110 C hotplate/ 80 sec. full contact 2nd layer 115 C hotplate/ 180 sec. full contact Exposure: Ultratech 1500 gh line Stepper Develop: AZ® 400K 1:4, continuous spray for 260 sec. @ 27 C
AZ® P4620 Lithographic Performance Summary
Process Conditions Substrate : Film-thickness : Softbake : Exposure : Dose : Development : Bare-Si 17µm 120˚C / 240 sec. (DHP) Canon PLA-501F (ghi-line) 630 mJ/cm2 AZ 400K Developer 1:4, Immersion - 300 sec., 23˚C
AZ® P4620 Gold Plating Process
Photoresist Mask CD = 93.5um; Au Bump CD = 96um.
AZ Confidential
AZ, the AZ logo, BARLi, Aquatar, nLOF, Kwik Strip, Klebosol, and Spinfil are registered trademarks and AX, DX, HERB, HiR, MiR, NCD, PLP, Signiflow, SWG, and TARP are trademarks of AZ Electronic Materials.
7.0 µm
4.0 µm
5.0 µm
6.0 µm
AZ P4620•@ Lithography performance
800mJ/cm² 900 mJ/cm² 1000 mJ/cm² 1100 mJ/cm² 1200 mJ/cm²
10.0 µm Contact Holes 1:1 Pitch
800mJ/cm² 900 mJ/cm² 1000 mJ/cm² 1100 mJ/cm² 1200 mJ/cm²
AZ® P4620 Gold Plating Process
FT: Softbake:
28um, Single Coat 1) 100ºC / 500 sec. (Hotplate) 2) 90ºC / 180 min. (Oven) Rehydration time: 60 minutes Exposure: UTS-SS-III (ghi-line) Develop: AZ 400K 1:3, 21.5ºC Plating: Cyanide Gold Plating Solution
' ellipsometric: P4000
Absorbance ('k')
2.00
1.50
1.00
0.50
0.00 175
200
225
250
275
300
325
350
375
400
425
450
475
500
Wavelength (nm )
BU Electronic Materials
AZ P4620•@ Lithography performance
Process Conditions:
Optitrac Coat/ Bake Coat: Static dispense on Silicon Target Film Thickness: 12 µm Softbake: 110C hotplate/ 80 sec. full contact Exposure: Ultratech 1500 gh line Stepper Develop: AZ® 300 MIF, continuous spray for 200 sec. @ 23 C
2050 mJ/cm²
Film Thickness: 24 µm Optitrac coat and Bake SB: 1st layer 110 C / 80 sec 2nd layer 115 C /180 sec Ultratech 1500 gh line Stepper AZ 400K 1:4, 260 sec continuous spray @ 27 C
AZ® P4000 Series Spin Speed Curve
AZ, the AZ logo, BARLi, Aquatar, nLOF, Kwik Strip, Klebosol, and Spinfil are registered trademarks and AX, DX, HERB, HiR, MiR, NCD, PLP, Signiflow, SWG, and TARP are trademarks of AZ Electronic Materials.
Analysis:
Amray SEM
AZ P4620•@ Lithography performance
12 µm 10 µm 9.0 µm 8.0 µm
Film Thickness: 12 µm Optitrac coat and Bake SB: 110 C / 80 sec Ultratech 1500 gh line Stepper AZ 300 MIF, 200 sec continuous spray @ 23 C
Analysis:
Amray SEM
AZ P4620•@ Lithography performance
1650 mJ/cm² 1750 mJ/cm² 1850 mJ/cm² 1950 mJ/cm² 2050 mJ/cm²
1650 mJ/cm²
1750 mJ/cm²
1850 mJ/cm²
1950 mJ/cm²
Film Thickness: 12 µm Optitrac coat and Bake SB: 110 C / 80 sec Ultratech 1500 gh line Stepper AZ 300 MIF, 200 sec continuous spray @ 23 C
10.0 µm Contact Holes 1:0.3 Pitch
AZ® P4620 Photoresist Data Package
The information contained herein is, as far as we are aware, true and accurate. However, no representations or warranties, either express or implied, whether of merchantable quality, fitness for any particular purpose or of any other nature are hereby made in respect of the information contained in this presentation or the product or products which are the subject of it. In providing this material, no license or other rights, whether express or implied, are given with respect to any existing or pending patent, patent application, trademarks, or other intellectual property right.
AZ® P4620 Gold Plating Process
AZ Confidential
AZ, the AZ logo, BARLi, Aquatar, nLOF, Kwik Strip, Klebosol, and Spinfil are registered trademarks and AX, DX, HERB, HiR, MiR, NCD, PLP, Signiflow, SWG, and TARP are trademarks of AZ Electronic Materials.
AZ Confidential
AZ, the AZ logo, BARLi, Aquatar, nLOF, Kwik Strip, Klebosol, and Spinfil are registered trademarks and AX, DX, HERB, HiR, MiR, NCD, PLP, Signiflow, SWG, and TARP are trademarks of AZ Electronic Materials.
200
225
250
275
300
325
350
375
400
425
450
475
500
Wavelength (nm )
BU Electronic Materials
AZ® P4000 Unbleached Absorbance Curve
AZ P4000 Series resist(s) Ellipsometrc Absorbance Normalized to 1/µm
AZ® P4000 Bleached Absorbance Curve
PALM注册码大全
1、【记帐软件】AdarianMoney3.6 sn：7775-5170-2795-4851
2、【钻石2代游戏】bejeweled2任意八位
3、【游戏软件】BikeOrDie1.3a 42129
4、【台球游戏】Billiard 4.2 s/n:765-483297542
5、【一套优秀的 Outline 软件】Bonsai 049-7WSM533W46MW679SW3-8S
20、【一个高度可定制的程序启动工具，可以取代你目前Palm设备上的内置管理器】LauncherX 8281282524C07CBD
LauncherX1[1].2.2 33933 7BFC0CFBA787A08211
21、【金字塔祖吗游戏】Luxor W44M9OF3
22、【蒙恬手写】PENP2.0 4OCB2ZVWL7T1
10、【行事例软件】Datebk6 3CQ36C
11、【日记型的记事本】DayNotez 057-7WSM533W46MW679SW3-7S
12、【炸弹专家游戏】ExplodeArena_v1.30 18585
13、【游戏软件】GoldMiner 2B6AC5FD
14、【数据库软件】Handbase 2029-9115-3709-8302 2263875567098298
4.0Student 5.00
serial: 496535
4Corners Solitaire
g326ut87c
AbcLotto 2.0
3714
Abroad!
999-58527
Accordion Solitaire 1.0
j23km8z27
AceMail 1.x
AZ P4620 Photoresist数据包说明书
Red=Neg, Blue =Pos; nLOF, N4000, 15nXT, 12XT, 40XT = chemically amplified; 125nXT = photopolymer; 10XT, 9200, P4620, 2008HS, PLP, 50XT, 4500 = DNQ
AZ® Electronic Materials
AZ® nLOF Series
<--------------------- AZ® 2008HS ------------------->
AZ® TX 1311
<------ AZ® 9260/10XT -------->
AZ®
<------------ AZ® 50XT ----------> AZ® VS-01HJ
40XT Series CA
125nXT Series PP
15nXT6HULHV&A
TX 1311
CA
λ
FT Range (um)
Maximum Aspect Single coat Ratio
Application
g-h 2 - 55
25
2:1 Solder, Cu, Au
g-h 2 - 55
AZ® P4620 Gold Plating Process
Photoresist Mask CD = 93.5um; Au Bump CD = 96um.
AZ Confidential
AZ, the AZ logo, BARLi, Aquatar, nLOF, Kwik Strip, Klebosol, and Spinfil are registered trademarks and AX, DX, HERB, HiR, MiR, NCD, PLP, Signiflow, SWG, and TARP are trademarks of AZ Electronic Materials.
DS-2XC6646G0 P-IZH(R)S 4 MP ANPR IR Varifocal Bull
DS-2XC6646G0/P-IZH(R)S4 MP ANPR IR Varifocal Bullet Network Camera⏹High quality imaging with 4 MP resolution⏹Excellent low-light performance via DarkFighter technology⏹Clear imaging against strong back light due to 120 dB WDR technology⏹License Plate Recognition⏹Efficient H.265+ compression technology to save bandwidth and storage⏹ 5 streams to meet a wide variety of applications⏹Water and dust resistant (IP67)⏹316L stainless steel enclosure, protecting cameras to be used in corrosive environments, providing reliability andlongevity compared to standard cameras⏹ A built-in wiper(-R) removes water and dust on the screen and ensures clear images when the camera is used in dustyor damp environmentsSpecificationCameraImage Sensor 1/1.8" Progressive Scan CMOSMax. Resolution 2688 × 1520Min. Illumination Color: 0.0005 Lux @ (F1.2, AGC ON), B/W: 0.0001 Lux @ (F1.2, AGC ON), 0 Lux with IR Shutter Time 1 s to 1/100,000 sDay & Night IR cut filterBlue glass module to reduce ghost phenomenonLensFocal Length & FOV 2.8 to 12 mm, horizontal FOV 100.8° to 40.2°, vertical FOV 53.3° to 22.5°, diagnol FOV 122.3° to 46.2°8 to 32 mm, horizontal FOV 40.7° to 14.6°, vertical FOV 22.3° to 8.3°, diagnol FOV 47.4°to 16.7°Focus Auto, semi-auto, manualAperture 2.8 to 12 mm: F1.38 to F2.5 8 to 32 mm: F1.7DORIDORI Wide:2.8 to 12 mm: D: 60 m, O: 23.8 m, R: 12 m, I: 6 m8 to 32 mm: D: 150.3 m, O: 59.7 m, R: 30.1 m, I: 15 m Tele:2.8 to 12 mm: D: 149 m, O: 59.1 m, R: 29.8 m, I: 14.9 m 8 to 32 mm: D: 400 m, O: 158.7 m, R: 80 m, I: 40 mIlluminatorSupplement Light Type IRSupplement Light Range 2.8 to 12 mm: 60 m 8 to 32 mm: 100 mSmart Supplement Light YesIR Wavelength 850 nm VideoMain Stream 50 Hz: 25 fps (2688 × 1520, 2560 × 1440, 1920 × 1080, 1280 × 720) 60 Hz: 30 fps (2688 × 1520, 2560 × 1440, 1920 × 1080, 1280 × 720)Sub-Stream 50 Hz: 25 fps (704 × 576, 640 × 480) 60 Hz: 30 fps (704 × 480, 640 × 480)Third Stream 50 Hz: 25 fps (1920 × 1080, 1280 × 720, 704 × 576, 640 × 480) 60 Hz: 30 fps (1920 × 1080, 1280 × 720, 704 × 480, 640 × 480)Fourth Stream 50 Hz: 25 fps (704 × 576, 640 × 480) 60 Hz: 30 fps (704 × 480, 640 × 480)Fifth Stream 50 Hz: 25 fps (704 × 576, 640 × 480) 60 Hz: 30 fps (704 × 480, 640 × 480)Video Compression Main stream: H.265+/H.265/H.264+/H.264Sub-stream/Fourth stream/Fifth stream: H.265/H.264/MJPEG Third stream: H.265/H.264Video Bit Rate 32 Kbps to 8 MbpsH.264 Type Baseline Profile/Main Profile/High Profile H.265 Type Main ProfileBit Rate Control CBR/VBRScalable Video Coding (SVC) H.265 and H.264 encodingRegion of Interest (ROI) 5 fixed regions for each streamTarget Cropping YesAudioAudio Type Mono soundAudio Compression G.711/G.722.1/G.726/MP2L2/PCM/AAC-LC/MP3Audio Bit Rate 64 Kbps (G.711)/16 Kbps (G.722.1)/16 Kbps (G.726)/32 to 192 Kbps (MP2L2)/16 to 64 Kbps (AAC-LC)/8 to 320 Kbps (MP3)Audio Sampling Rate 8 kHz/16 kHz/32 kHz/44.1 kHZ/48 kHz Environment Noise Filtering YesNetworkProtocols TCP/IP, ICMP, HTTP, HTTPS, FTP, SFTP, SRTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP, PPPoE, NTP,UPnP, SMTP, SNMP, IGMP, 802.1X, QoS, IPv6, UDP, Bonjour, SSL/TLS, WebSocket, WebSocketsSimultaneous Live View Up to 20 channelsAPI Open Network Video Interface (Profile S, Profile G, Profile T), ISAPI, SDK, ISUP User/Host Up to 32 users. 3 user levels: administrator, operator and userSecurity Password protection, complicated password, HTTPS encryption, 802.1X authentication (EAP-TLS, EAP-LEAP, EAP-MD5), watermark, IP address filter, basic and digest authentication for HTTP/HTTPS, WSSE and digest authentication for Open Network Video Interface, RTP/RTSP OVER HTTPS, Control Timeout Settings, Security Audit Log, TLS 1.2Network Storage NAS (NFS, SMB/CIFS), auto network replenishment (ANR)Together with high-end Hikvision memory card, memory card encryption and health detection are supported.Client iVMS-4200, Hik-Connect, Hik-CentralWeb Browser Plug-in required live view: IE10, IE11Plug-in free live view: Chrome 57.0+, Firefox 52.0+, Safari12+ Local service: Chrome 57.0+, Firefox 52.0+ImageImage Parameters Switch YesImage Settings Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance adjustable by client software or web browserDay/Night Switch Day, Night, Auto, Schedule, Alarm Trigger, Video TriggerWide Dynamic Range (WDR) 120 dBSNR ≥ 52 dBImage Enhancement BLC, HLC, Defog, 3D DNRPicture Overlay LOGO picture can be overlaid on video with 128 × 128 24bit bmp formatImage Stabilization EISInterfaceEthernet Interface 1 RJ45 10 M/100 M/1000 M self-adaptive Ethernet portOn-Board Storage Built-in memory card slot, support microSD/microSDHC/microSDXC card, up to 256 GBAudio 1 input (line in), two-core terminal block, max. input amplitude: 3.3 Vpp, input impedance: 4.7 KΩ, interface type: non-equilibrium; 1 output (line out), two-core terminal block, max. output amplitude: 3.3 Vpp, output impedance: 100 Ω, interface type: non-equilibriumAlarm 1 input, 1 output (max. 24 VDC, 1 A or max. 110 VAC, 500 mA)RS-485 Without -R: 1 RS-485 (half duplex, HIKVISION, Pelco-P, Pelco-D, self-adaptive) -R: does not supportReset Key YesWiegand /P: 1 Wiegand (CardID 26bit, SHA-1 26bit, Hik 34bit, NEWG 72bit) EventBasic Event Motion detection, video tampering alarm, exception (network disconnected, IP address conflict, illegal login, abnormal reboot, HDD full, HDD error), video quality diagnosis, vibration detectionSmart Event Line crossing detection, intrusion detection, region entrance detection, region exiting detection (support alarm triggered by specified target types (human and vehicle)) Scene change detection, audio exception detection, defocus detectionLinkage Upload to FTP/NAS/memory card, notify surveillance center, send email, trigger alarm output, trigger recording, trigger capture, audible warningDeep Learning FunctionRoad Traffic and Vehicle Detection Blocklist and allowlist: up to 10,000 recordsCaptures vehicle that has no license plateSupport license plate recognition of motorcycles (only in checkpoint scenario) Support vehicle attribute detection, including vehicle type, color, brand, etc. (City Street mode is recommended.)Metadata Metadata of road traffic is supported. GeneralPower 12 VDC ± 20%, 1.8 A, max. 22 W, three-core terminal blockPoE: 802.3at, Type 2, Class 4, 42.5 V to 57 V), 0.5 A to 0. 4 A, max. 22 WMaterial 316L and anti-corrosion coatingDimension With -R: 240.8 mm × 145 mm × 166.6 mm (9.5" × 5.7" × 6.6") Without -R: 224 mm × 145 mm × 143.5 mm (8.8" × 5.7" × 5.6")Package Dimension 477 mm × 235 mm × 302 mm (18.7" × 9.3" × 11.9")Weight With -R: approx. 4265 g (9.4 lb.) Without -R: approx. 3710 g (8.2 lb.)With Package Weight With -R: approx. 5115 g (11.3 lb.) WIthout -R: approx. 4560 g (10.1 lb.)Storage Conditions -40 °C to 60 °C (-40 °F to 140 °F). Humidity 95% or less (non-condensing) Startup and OperatingConditions-40 °C to 60 °C (-40 °F to 140 °F). Humidity 95% or less (non-condensing)Language 33 languages: English, Russian, Estonian, Bulgarian, Hungarian, Greek, German, Italian, Czech, Slovak, French, Polish, Dutch, Portuguese, Spanish, Romanian, Danish, Swedish, Norwegian, Finnish, Croatian, Slovenian, Serbian, Turkish, Korean, Traditional Chinese, Thai, Vietnamese, Japanese, Latvian, Lithuanian, Portuguese (Brazil), UkrainianGeneral Function Anti-banding, 5 streams, heartbeat, mirror, privacy mask, flash log, password reset via email, pixel counterHeater YesWiper -R: Yes ApprovalEMC FCC: 47 CFR Part 15, Subpart BCE-EMC: EN 55032: 2015, EN 61000-3-2:2019, EEN 61000-3-3:2013+A1:2019, EN 50130-4: 2011 +A1: 2014RCM: AS/NZS CISPR 32: 2015IC: ICES-003: Issue 7KC: KN 32: 2015, KN 35: 2015Safety UL: UL 62368-1CB: IEC 62368-1:2014+A11CE-LVD: EN 62368-1:2014/A11:2017BIS: IS 13252(Part 1):2010/ IEC 60950-1 : 2005 LOA: IEC/EN 60950-1Environment CE-RoHS: 2011/65/EUWEEE: 2012/19/EUReach: Regulation (EC) No 1907/2006Protection IP67: IEC 60529-2013IK10: IEC 62262: 2002 (without -R)Anti-Corrosion Protection NEMA 4X: NEMA 250-2018C5-M: 720H neutral salt spray, 480H water condensation;Exterior environments: industrial areas with high humidity and aggressive atmosphere and coastal areas with high salinity;Interior environments: buildings or areas with almost permanent condensation and with high pollution.⏹FunctionRoad Traffic and Vehicle DetectionWith embedded deep learning based license plate capture and recognition algorithms, the camera alone can achieve plate capture and recognition. The algorithm enjoys the high recognition accuracy of common plates and complex-structured plates, which is a great step forward comparing to traditional algorithms. Blocklist and allowlist are available for plate categorization and separate alarm triggering.⏹Typical ApplicationHikvision products are classified into three levels according to their anti-corrosion performance. Refer to the following description to choose for your using environment.This model has TOP-LEVEL PROTECTION.Level DescriptionTop-level protection Hikvision products at this level are equipped for use in areas where professionalanti-corrosion protection is a must. Typical application scenarios include coastlines, docks,chemical plants, and more.Moderate protection Hikvision products at this level are equipped for use in areas with moderate anti-corrosiondemands. Typical application scenarios include coastal areas about 2 kilometers (1.24miles) away from coastlines, as well as areas affected by acid rain.No specific protection Hikvision products at this level are equipped for use in areas where no specificanti-corrosion protection is needed.050704020220921⏹ Dimension⏹ Accessory⏹Optional DS-1704ZJ-Y-AC(OS)Wall Mount⏹ Available ModelDS-2XC6646G0/P-IZHS (2.8 to 12 mm, 8 to 32 mm) DS-2XC6646G0/P-IZHRS (2.8 to 12 mm, 8 to 32 mm)。
AZ P4000系列正相光刻胶技术数据表说明书
Technical datasheetAPPLICATIONGeneral purpose positive tone photoresists featuring a special PAC (Photo Active Compound) engineered to prevent poisoning of plating solutions and extend plating bath life. Excellent substrate adhesion for wet etch applications.•Wide compatibility with electro -plating solu-tions•Safe solvent•Single coat thicknesses from 1.0 to >20µm •May be cured as a permanent dielectric in-* Contact your AZ product representative for more in-formation and special spin programs for ultra thick films.COMPANION PRODUCTSThinning/Edge Bead RemovalAZ ®EBR Solvent or AZ® EBR 70/30 DevelopersAZ ® 400K 1:3 or 1:4, AZ ® 421K, AZ Developer 1:1, AZ 340 RemoversAZ ® 300T, AZ ® 400T, AZ Kwik StripAZ® P4000 SeriesPositive Tone PhotoresistsTYPICAL PROCESSSoft Bake: 90-115C*Rehydrate: for films > 4.0µm thick Expose: 350-450nm sensitive Develop: Spray or immersionDeveloper type: Inorganic (IN) * Use higher soft bake temp. for best adhesion to metals. Ramped temperature may be required for thicker films.OPTICAL CONSTANTS*96µm gold bump plated in AZ P4620 Cyanide electro -plating solutionTYPICAL SPIN CURVES (150MM SUBSTRATE)Note: Thicker films will be coated by varying spin times and other dispense parameters (or via multiple coats). Single films above 7.0µm are not spun to equilibrium.TYPICAL AU PLATING RESULTS (CYANIDE PLATING SOLUTION; PH = 5.5)Resist: AZ P4620Thickness: 24µmDevelop: AZ 400K 1:3Plating Temp: 45CPlating Time: 50 min.Metal Thickness: 20µmStrip: AZ 400TREFERENCE PROCESS (12µM THICK AZ P4620 FILM)* Thicker films may require a ramped soft bake process to avoid bubble formation due to rapid outgassing ofsolvents. Contact your AZ product representative for ultra-thick coat and bake processing guidelines.EXPOSURE LATITUDE FOR 20µM LINES AZ P4620 AT FT = 12µM EXPOSURE LATITUDE FOR 40µM LINES AZ P4620 AT FT = 24µMABSORBANCE SPECTRA OF P4000 SERIES PHOTORESISTS (UNBLEACHED, NORMAL-IZED TO 1µM)PROCESSING P4000 AS A DIELECTRIC INSULATORAZ P4000 Series photoresists may be thermally cured after develop to form stable dielectric isolators. The die-lectric properties are cure temperature dependent as shown in the table below.EXAMPLE COATING SEQUENCE FOR 20+ µM THICK FILMSAZ P4000 SERIES FLUID VISCOSITIESDILL MODELLING PARAMETERSAPPROXIMATE EXPOSURE DOSE REQUIRE-MENT VS. FILM THICKNESS (SUSS MA -200)PROCESS CONSIDERATIONSSUBSTRATE PREPARATIONSubstrates must be clean, dry, and free of organic residues. Oxide forming substrates (Si, etc.) should be HMDS primed prior to coating AZ P4000. Contact your AZ product representative for detailed information on pre-treating with HMDS.COATINGFilms up to 8.0µm thick (depending upon wafer size) may be set and spun to equilibrium using the spin curve graphs as a reference. Thicker films require special coat programs using carefully timed spread and spin cycles. Contact your AZ products representative for additional information.SOFT BAKESoft bake times and temperatures may be application specific. Process optimization is recommended to ensure stable lithographic and adhesion performance. Soft bake temperatures for AZ P4000 should be in the 95-115C range. Temperatures towards the high end of this range will improve adhesion to most metals. Thick films may require gradual ramping of the soft bake temperature to prevent bubbling.FILM REHYDRATIONP4000 photoresist films thicker than 4.0µm require a rehydration hold between soft bake and exposure. Hold times are typically 30-60 minutes (depending upon film thickness) @ relative humidity 40 - 45%.EXPOSUREAZ P4000 is sensitive to exposure wavelengths between 310 and 450nm. 365-436nm is recommended.POST EXPOSE BAKEA PEB is not generally required for P4000 but may be employed to maximize process latitudes and to mitigate standing wave effects caused by monochromatic exposure. PEB temperatures and times may be application specific. As a general rule, PEB temperatures should be in the 100 to 115C range.DEVELOPINGSpray or immersion developing in AZ 400K series developers is recommended. AZ 400K 1:3 or AZ 421K (unbuffered) are recommended for resist film thicknesses above 12µm. AZ 400K 1:4 provides improved devel-oper selectivity for thinner films. AZ Developer 1:1 may be used in applications requiring zero etch rate on Alu-minum substrates.HARD BAKEHard baking (post develop bake) improves adhesion in wet etch or plating applications and improves pattern stability in dry etch processes. Hard bake temperatures should be in the 100 to 110C range to ensure minimal thermal distortion of the pattern. Higher temperatures may be used to cure the pattern (cross link the resin) for use as a permanent insulator.COMPATIBLE MATERIALSAZ P4000 Series materials are compatible with all commercially available lithography processing equipment. Compatible materials of construction include glass, quartz, PTFE, PFA, stainless steel, HDPE, polypropylene, and ceramic.Rev. (08/21)Products are warranted to meet the specifications set forth on their label/packaging and/or certificate of analysis at the time of shipment or for the expressly stated duration. MERCK MAKES NO REPRESENTATION OR WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE REGARDING OUR PRODUCTS OR ANY INFORMATION PROVIDED IN CONNECTION THEREWITH. Customer is responsible for and must independently determine suitability of Merck´s products for customer ’s products, intended use and processes, including the non -infringement of any third parties´ intellectual property rights. Merck shall not in any event be liable for incidental, consequential, indirect, exemplary or special damages of any kind resulting from any use or failure of the products: All sales are subject to Merck ’s complete Terms and Conditions of Sale. Prices are subject to change without notice. Merck reserves the right to discontinue products without prior notice.The information on our trademarks is available in the Trademarks section on . Detailed information on our trademarks is also available via publicly accessible resources. All other trademarks are the property of their respective owners. © 2021 Merck KGaA, Darmstadt, Germany and/or its affiliates.DisclaimerHANDLING/DISPOSALAZ P4000 Series materials are flammable liquids containing PGMEA (1-Methoxy -2-propanol acetate). Refer to the current version of the MSDS and to local regulations for up to date information on safe handling and proper disposal. AZ P4000 is compatible with drain lines handling similar organic solvent based materials.。
AK4620A中文资料
- Selectable Single-ended or Differential Input - High Performance Linear Phase Digital Anti-Alias Filter
Passband: 0 ~ 20.25kHz (@fs=44.1kHz) Ripple: ± 0.005dB Stopband Attenuation: 100dB - S/(N+D): 92dB (single-ended)
Output digital Attenuator
DAC DSD mode DAC Zero-data detection X’tal Oscillating Circuit Master Mode Parallel Mode
AK4524
96kHz Single-ended 0dB ~ +18dB 0.5dB/step Mute, -72dB ~ 0dB Pseudo-log step
92dB
100dB
110dB
113dB
100dB
X
100dB
115dB
Mute, -48dB ~ 0dB Mute, -48dB ~ 0dB
Linear 256 steps Linear 256 steps
X
X
-
-
X
X: Available, -: NOT available
MS0368-E-00 -2-
Bias voltage of ADC inputs and DAC outputs.
2 AINR+
I Rch Positive Input Pin
alaris 集成式A4 Legal尺寸平板附件 用户指南说明书
1. 打开平板盖。
2. 使用 Brillianize 清洁剂（步骤 1）擦拭玻璃压板。为了达到最佳效果， 只能单向擦拭 （例如从右向左）。
更多信息。 • 请根据环境因素控制此材料的弃置。有关回收或再利用信息，请联系您的当地政府，如果在美国，请访问：
/go/scannerrecycling。 • 产品包装材料可循环使用。 • 零件也可回收或再利用。 • 化学产品的 “安全数据页” (SDS) 可从下列 Kodak Alaris 网站获取：/go/ehs。通过网站访
6
A-61884_zh-cn 2017 年 10 月
使用手动裁剪模式
使用 Alaris 集成式 A4/Legal 尺寸平板附件
如果您通过平板进行扫描，并将手动选择设置为裁剪模式，请从左上角 （原位置应为 0，0）开始裁剪，并确保您的文档正确位于平板的右下角。 如果您要扫描书籍 （或厚文档），则应将裁剪模式选择为手动选择。
集成式 A4/Legal 尺寸平板附件
用户指南
A-61884_zh-cn
安全
用户防范措施
• 只在室内干燥的位置使用扫描仪和电源。 • 确保电源插座与扫描仪的距离不超过 1.52 米 （5 英尺），以便于插接。 • 请勿损坏、捆扎、切割或修改电源线。 • 仅使用随 S2000 或 S2000w 扫描仪提供的交流适配器。请确保电源线已稳固插入墙上电源插座。 • 请勿将集成式 A4/Legal 尺寸平板附件的电源线插入除 Alaris S2000 或 S2000w 之外的任何其他设备。 • 在电源插座周围保留足够空间，以便在出现紧急情况时可轻易拔下扫描仪的电源线。 • 如果扫描仪出现不寻常热烫、有奇怪的气味、冒烟或发出不熟悉的噪音，请勿使用。立即停止扫描仪操作并从墙上
Aperio WebViewer DX IT管理员指南说明书
Aperio WebViewer DXIT Administrator’s GuideMAN-0491 Revision A | April 2022Aperio WebViewer DX IT Administrator’s GuideThis document applies to Aperio WebViewer DX 1.0 and later.Copyright NoticeÌCopyright © 2022 Leica Biosystems Imaging, Inc. All Rights Reserved. LEICA and the Leica logo are registered trademarks of Leica Microsystems IR GmbH. Aperio is a trademark of the Leica Biosystems group of companies in the USA and optionally in other countries.Other logos, product and/or company names might be trademarks of their respective owners.ÌThis product is protected by registered patents. For a list of patents, contact Leica Biosystems.Customer ResourcesÌFor the latest information on Leica Biosystems Aperio products and services, please visit /Aperio.Contact Information – Leica Biosystems Imaging, Inc.0815477020280(8012) 1.023WVROWIVDAperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 2022 2ContentsNotices (4)Revision Record (4)Intended Purpose (4)Cautions and Notes (4)Symbols (6)1 Introduction (9)Aperio WebViewer DX Overview (9)Supporting System Compatibility (9)Supported Image Types (10)Nonclinical Use Images (10)Installation (10)Environment (10)Supported Operating System and Browsers (10)Required Viewing Settings (10)Monitor Settings (10)Browser and Operating System Settings (11)2 Specifications and Requirements (12)Monitors and Viewing Workstations (12)Monitor Specifications (12)Recommended Monitor Display Image Validation (13)Viewing Workstation Specifications (13)Server Specifications (14)Using a Virtual Machine as Your Aperio eSlide Manager Server (14)Localization (14)3 Network Configuration and Performance (15)Network Configuration (15)Network Performance Considerations (16)User Interface Performance and Network Latency (16)User Interface Performance and Network Bandwidth (17)Index (18)Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 20223NoticesRevision RecordIntended PurposeAperio WebViewer DX is a viewing software application intended to enable the pathologist with the qualitative review and interpretation of digital images of surgical pathology glass slides prepared from formalin-fixed paraffin-embedded (FFPE) tissue. Aperio WebViewer DX is intended for use with digital images from compatible scanners on local and remote networks. Aperio WebViewer DX is not intended for use with a frozen section, cytology or non-FFPE specimens. It is the responsibility of a qualified pathologist to employ appropriate procedures and safeguards to assure the validity of the interpretation of images obtained using Aperio WebViewer DX.Cautions and Notes`Aperio WebViewer DX is for professional use only.`Serious Incidents Reporting - Any serious incident that has occurred in relation to the Aperio WebViewer DX shall bereported to the manufacturer and the competent authority of the member state in which the user and/or the patient is established.`Specifications and Performance - For information on the requirements for monitors, see “Monitors and ViewingWorkstations” on page 12.`Installation - Aperio WebViewer DX must be installed by a trained Leica Biosystems Technical Servicesrepresentative.`Accessories - For information on using Aperio WebViewer DX with third-party accessories such as a LaboratoryInformation System (LIS) not provided by Leica Biosystems, contact your Leica Biosystems Technical Servicesrepresentative.`Quality Control -For information on quality control procedures for Pathologist and Histotechnicians, refer to theAperio WebViewer DX User’s Guide.`Maintenance and Troubleshooting -For information on maintenance and troubleshooting, refer t o the AperioWebViewer DX User’s Guide.`Cybersecurity - Be aware that workstations are susceptible to malware, viruses, data corruption, and privacybreaches. Use caution when inserting USB drives and other removable devices. Consider disabling USB ports thatare not in use. If you plug in a USB drive or other removable device, you should scan the devices with an anti-malware utility. Work with your IT administrators to protect your workstation by following your institution’s password andsecurity policies.4Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 2022Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 20225IT staff: See the Aperio eSlide Manager Administrator’s Guide for further cybersecurity recommendations, including: `Protecting workstations and servers`Setting passwords`Monitoring and restricting login attempts`Sensitive Data Protection - This Leica Biosystems product is capable of input, storage, and handling of sensitivedata, including personal identifier information (PII) and/or possibly protected health information (PHI). In addition to personal data such as name, address, and other obvious personal identifiers, sensitive data include barcodes,accession numbers, diagnostic information, and scan images, such as microscope slide labels and other labels or annotations embedded in image files. Please take appropriate precautions to protect from sensitive data exposure and theft. Handling of sensitive data is subject to local laws. Many countries have a data protection authority toensure that data protection law is followed. For more information about your privacy rights, or if you are not able to resolve a problem directly with us and wish to make a complaint, contact your local authority.`Private Health Information Protection - Due to limitations of the operating system, Private Health Information (PHI)data cannot be protected in transit. Leica Biosystems recommends protecting data in transit by using SSL withstrong security protocols, such as Transport Layer Security (TLS), or network-level encryption, such as IPSec or SSH tunnelling.`Off-the-Shelf Software - Potential impacts to cybersecurity in response to off-the-shelf (OTS) software are managedby Leica Biosystems, Inc. A list of all OTS software is maintained by Leica Biosystems, Inc. For more informationon OTS, contact your Leica Biosystems Sales Representative and ask for a copy of of the Aperio WebViewer DXSoftware Bill of Materials (SBOM). OTS failures can cause errors when viewing or loading images in the viewer,including inaccurate color representation or other visual anomalies. If you experience issues with loading or viewing images, contact Leica Biosystems Technical Services.`Aperio SSL Certificates - For information on internally-generated Aperio SSL certificates and recommendations forprocuring additional SSL certificates, see the Aperio eSlide Manager Administrator’s Guide .`Training - This manual is not a substitute for the detailed operator training provided by Leica Biosystems or for otheradvanced instruction. Leica Biosystems Technical Services should be contacted immediately for assistance in theevent of any malfunction.CAUTIONS: When viewing digital slides:`Do not use the Image Enhancement tools to correct a suboptimal scanned image fordiagnostic review. In this case, you should request a re-scan of the slide.`Your monitor must meet the specifications detailed in “Monitor Specifications” onpage 12.`Your monitor’s Display Mode must be set to sRGB.`Your viewing station must use the supported browser and operating system, asdescribed in, “Supported Operating System and Browsers” on page 10.SymbolsThe following symbols appear in device labeling:6Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 2022Customer Service Contacts Please contact the office for your country for technical assistance.Australia:96 Ricketts RoadMount Waverly, VIC 3149AUSTRALIATel: 1800 625 286 (toll free)Between 8:30 AM-5 PM, Monday-Friday, AESTEmail:*********************************** Austria:Leica Biosystems Nussloch GmbHTechnical Assistance CenterHeidelberger Strasse 17Nussloch 69226GERMANYTel: 0080052700527 (toll free)In-country Tel: +43 1 486 80 50 50Email:******************************België/Belgique:Tel: 0080052700527 (toll free)In-country Tel: +32 2 790 98 50Email:****************************** Canada:Tel: +1 844 534 2262 (toll free)Direct International Tel: +1 760 539 1150Email:********************************China:17F, SML Center No. 610 Xu Jia Hui Road, Huangpu District Shanghai, PRC PC:200025CHINATel: +86 4008208932Fax: +86 21 6384 1389Email:********************************* RemoteCareemail:***************************** Danmark:Tel: 0080052700527 (toll free)In-country Tel: +45 44 54 01 01Email:******************************Deutschland:Leica Biosystems Nussloch GmbH Technical Assistance Center Heidelberger Strasse 17Nussloch 69226GERMANYTel: 0080052700527 (toll free)In-country Tel: +49 6441 29 4555 Email:****************************** Eire:Tel: 0080052700527 (toll free)In-country Tel: +44 1908 577 650 Email:****************************** España:Tel: 0080052700527 (toll free)In-country Tel: +34 902 119 094 Email:********************************* France:Tel: 0080052700527 (toll free)In-country Tel: +33 811 000 664 Email:****************************** Italia:Tel: 0080052700527 (toll free)In-country Tel: +39 0257 486 509 Email:********************************* Japan:1-29-9 Takadanobaba, Shinjuku-ku Tokyo 169-0075JAPANNederland:Tel: 0080052700527 (toll free)In-country Tel: +31 70 413 21 00 Email:******************************Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 20227New Zealand:96 Ricketts RoadMount Waverly, VIC 3149AUSTRALIATel: 0800 400 589 (toll free)Between 8:30 AM-5 PM, Monday-Friday, AESTEmail:***********************************Portugal:Tel: 0080052700527 (toll free)In-country Tel: +35 1 21 388 9112Email:******************************The Russian FederationBioLine LLCPinsky lane 3 letter ASaint Petersburg 197101THE RUSSIAN FEDERATIONTel: 8-800-555-49-40 (toll free)In-country Tel: +7 812 320 49 49Email:***************Sweden:Tel: 0080052700527 (toll free)In-country Tel: +46 8 625 45 45Email:******************************Switzerland:Tel: 0080052700527 (toll free)In-country Tel: +41 71 726 3434Email:******************************United Kingdom:Tel: 0080052700527 (toll free)In-country Tel: +44 1908 577 650Email:******************************USA:Tel: +1 844 534 2262 (toll free)Direct International Tel: +1 760 539 1150Email:********************************8Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 2022Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 20229Aperio WebViewer DX OverviewAperio WebViewer DX is a web-based digital slide viewing software product that enables you to navigate through whole slide images for a patient case in an organized manner for the purpose of on-screen primary diagnosis. You can open whole slide images in Aperio WebViewer DX from an image and data management system (IDMS), such as Aperio eSlide Manager, or from your Laboratory Information System (LIS).The Aperio WebViewer DX is part of an overall clinical workflow solution, which also includes the Aperio GT 450 DX scanner, Aperio eSlide Manager, and a LIS connectivity solution.Aperio eSlide Manager (IDMS)Aperio GT 450 DX Scanner Aperio GT 450 DXSAM SoftwareAperio WebViewer DX with Supported Monitor Aperio LIS ConnectivitySolution LISLAN/WAN orInternet Supporting System CompatibilityAperio WebViewer DX is compatible with the following Leica Biosystems systems and offerings.1IntroductionChapter 1: IntroductionSupported Image TypesAperio WebViewer DX supports SVS images created from the Aperio GT 450 DX for use in your clinical workflow.Nonclinical Use ImagesYou can open and view SVS images from an Aperio scanner other than the Aperio GT 450 DX; however, they are for nonclinical use only. When you open such an image, a banner appears at the bottom of the viewer indicating the image is for nonclinical use only.InstallationInstallation and setup of Aperio WebViewer DX and Aperio eSlide Manager should only be performed by a trained Leica Biosystems Service representative.EnvironmentAperio WebViewer DX is intended for use in Histology and Pathology labs as well as within a pathologist’s office for quality control tasks, routine diagnosis, and digital slide reviews. The pathologist’s office may be at their home or place of work. Supported Operating System and BrowsersRequired Viewing SettingsMonitor SettingsEnsure your monitor’s Display Mode is set to sRGB.10Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 2022Chapter 1: IntroductionBrowser and Operating System SettingsTo display your digital slides with optimal image quality, you must use the following browser and operating system settings:If your settings are outside of the specified range, the icon appears on the image to alert you that the image quality is reduced.Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 202211Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 202212This chapter contains specifications and requirements for monitors, viewing workstations, servers, and the network environment on which you are using Aperio WebViewer.Monitors and Viewing WorkstationsWARNING: Your monitor and viewing workstation must meet the required specifications provided in this section to ensure proper image rendering and display. Using a monitor that does not meet the required specifications can enable the use of incorrect color profiles.Work with the IT professionals in your organization to ensure your viewing workstation and monitors meet or exceed the recommended specifications. The workstation and monitor requirements are specified below.Monitor SpecificationsViewing workstation monitors must meet the specifications described below in order to ensure the viewer accurately renders the pixel color and sharpness (that is, resolution and contrast).iWhen searching for a monitor to purchase, we recommend using the Color Gamut specification listed in the table belowas a search criteria. This often results in monitors that meet the other required specifications.2Specifications and RequirementsChapter 2: Specifications and RequirementsRecommended Monitor Display Image ValidationAperio WebViewer DX includes a Monitor Display Image Validation feature, which uses a test image (TG18-QC) to ensure your monitor displays digital slide images correctly. Leica Biosystems recommends performing the manual Monitor Display Image Validation for an initial inspection and subsequent periodic inspections of the display and viewer functions, including brightness, sharpness, artifacts, and perceptual uniformity.For more information and instructions on performing the manual Monitor Display Image Validation, see the Aperio WebViewer DX User’s Guide.Viewing Workstation SpecificationsThe table below provides recommended specifications and settings for your viewing workstation. If the workstation exceeds the recommended specifications, the viewer’s performance can increase. If the workstation does not meet the recommended specifications, the viewer’s performance can decrease.Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 202213Chapter 2: Specifications and RequirementsServer SpecificationsYou can operate Aperio WebViewer DX from servers that meet the minimum requirements described below. However, to achieve the maximum performance, your servers should meet or exceed the recommended requirements. The viewer achieves optimal viewing performance when there are less than 30 users viewing cases simultaneously. In this environment, it takes about three seconds to open a digital slide. The viewer can support up to 60 users viewing cases simultaneously; however, its responsiveness may be reduced by 50%.Using a Virtual Machine as Your Aperio eSlide Manager ServerIf you are using a virtual machine (VM) as the server, you will see better performance in a virtual environment if your VM meets the recommended requirements shown in the tables above and has dedicated resource allocation on the virtual host. LocalizationWe do not support localization of our software. To ensure proper operation, the region settings of servers, client workstations, and browsers should be English (United States), set in the Windows Regional and Language Options windows available from the Windows Control panel. In addition, the English language Windows pack should be installed on the DSR (Digital Slide Repository), which is the server on which your images are stored.14Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 2022Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 202215Network ConfigurationThe following diagram shows the required network configuration for Aperio WebViewer DX, and how Aperio WebViewer DX interconnects with Aperio eSlide Manager.BrowserAperio WebViewer DXAperio eSlide Manager Server File SystemAperio eSlide ManagerDatabaseAperio eSlide Manager Proxy ServerAperio eSlide ManagerDataServerImage ServerAperio eSlide Manager Server LegendAperio WebViewer DX Aperio eSlide Manager Secure data link Non-secure data linkLabel on arrows: Protocol(s) and port numbers.3Network Configuration and PerformanceChapter 3: Network Configuration and PerformanceNetwork Performance ConsiderationsThis section contains information on how network latency and bandwidth impact user interface performance of Aperio WebViewer DX. This information is provided to assist in planning your network environment.User Interface Performance and Network LatencyThe table and graph in this section provide details on how network latency impacts user interface performance of the viewer. As the data demonstrates, an increase in network latency causes a decrease in the viewer’s performance. To provide the best user experience, the connection between the users and the software should be low latency.16Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 2022Chapter 3: Network Configuration and PerformanceUser Interface Performance and Network BandwidthThe graph in this section provides details on how network bandwidth impacts user interface performance of the viewer. As the data demonstrates, an increase to 10Mbps in network bandwidth provides an increase in the viewer’s performance.Aperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 202217Bbandwidth, performance considerations 17 browsers, supported 11Cconfiguration. See network configuration cybersecurity 15Eenvironment 10Iimage types 10installation 10IQ icon 11Llatency, performance considerations 16Nnetworkbandwidth 17configuration 15latency 16performance considerations 16 nonclinical images, using 10Ooperating system 11Pports. See network configuration Rrequired settings 10Sserver requirements 14 specifications viewing workstation 13IndexAperio WebViewer DX IT Administrator’s Guide, Revision A © Leica Biosystems Imaging, Inc. 2022 18/Aperio。
PerkinElmer 0822 平板探测器
PerkinElmer 平板探测器型号XRD 0822 AOXRD 0822 APXRD 1611 XPXRD 1620 XN CSXRD 1621 XNXRD 1622 AOXRD 1622 APXRD 1642 APXRD 0820系列X射线数字平板探测器维修德国PerkinElmer XRD 0820系列X射线数字平板探测器维修电路板维修XRD 0822 系列X射线数字平板探测器XRD-EP电源维修EL448197IXS160BP500P063X10071-b00303VJT1011283X射线检测技术和返修技术领先厂商VJ Technologies伟杰科技苏州RD0822 平板X射线探测器珀金埃尔默公司 XRD-0820-ES XRD-0840-ES主板电路板维修XRD 0820NA/CN/MN ESDEXELA 2315MAM DEXELA 2315MAM CL DEXELA 2923MAM CL Dexela 2321(In Development) Dexela 2321(In Development)Dexela 2321 DEXELA 1313LiteratureXRD 0822 AO， APXRD 1611 xPXRD 1622 AP3XRD 1622 AO， APXRD 1642 APXRpad 3025XRpad 4336XRpad 4343XRD 4343 RFXRD Series Product NoteXRD AccessoriesDEXELA NDTDEXELA Standard ProductsDEXELA MAM GigEDEXELA 2315 MAM CLDEXELA 2923 MAM CLDEXELA 1313DEXELA 2321大连PerkinElmer（珀金埃尔默.美国）XRD 0822平板X射线探测器XRD 8英寸（20厘米）平板X射线探测器丹东奥龙射线丹东市中讯安防XRD 0822 平板X射线探测器（FPDs）是PerkinElmer（珀金埃尔默.美国）公司出品的8英寸（20厘米）非晶硅的平板X射线探测器。
Photron FASTCAM Mini AX系列高速摄像头说明书
The FASTCAM Mini AX is Photron’s highest performance model within the FASTCAM Mini series ofhigh-speed cameras. The Mini AX delivers exceptional light sensitivity, excellent image quality and flexible region of interest (ROI) features for customers who do not require the ultimate frame rate performance of the FASTCAM SA-X2 and SA-Z, but would benefit from the same high-end camera image sensor features.Three performance level models - Mini AX50, AX100 and AX200 - deliver 1-megapixel image resolution (1024 x 1024 pixels) at frame rates up to 2,000fps, 4,000fps and 6,400fps respectively. All three Mini AX models offer a minimum exposure duration of 1µs as standard with recording memory options up to 32GB providing extended recording times and triggering flexibility.Subject to export approval the Mini AX100 can be offered with maximum frame rates up to 540,000fps and the Mini AX200 with maximum frame rates up to 900,000fps with a minimum exposure time of 260 nanoseconds.Standard operational features of the FASTCAM Mini AX include a mechanical shutter to allow remote system calibration, Gigabit Ethernet Interface for reliable system control with high-speed data transfer to PC, and the ability to remotely switch off cooling fans to eliminate vibration when recording at high magnifications.With the combination of high frame rates, high image quality and exceptional light sensitivity contained within a 120mm x 120mm x 94mm rugged camera body weighing just 1.5kg, the FASTCAM Mini AX is ideally suited for use in a wide range of demanding scientific and industrial applications.1-Megapixel CMOS Image Sensor:1024 x 1024 pixels at 2,000fps (Mini AX50)1024 x 1024 pixels at 4,000fps (Mini AX100)1024 x 1024 pixels at 6,400fps (Mini AX200)Maximum Frame Rate:170,000fps (Mini AX50 type 170K)212,500fps (Mini AX100 type 200K)540,000fps (Mini AX100 type 540K)216,000fps (Mini AX200 type 200K)540,000fps (Mini AX200 type 540K)900,000fps (Mini AX200 type 900k)Class Leading Light Sensitivity:ISO 12232 Ssat•ISO 40,000 monochrome •ISO 16,000 colorGlobal Electronic Shutter:1ms to 1μs independent of frame rate(Mini AX200 model 900K only: 260ns shutter available subject to export control)Dynamic Range (ADC):12-bit monochrome, 36-bit color Compact and Lightweight:120mm (H) x 120mm (W) x 94mm (D)4.72” (H) x 4.72” (W) x 3.70” (D) Weight: 1.5Kg (3.30 lbs.)Internal Recording Memory:8GB, 16GB, or 32GBFast Gigabit Ethernet Interface:Provides high-speed image download to standard notebook/PCFlexible Frame Synchronization: Frame rate may be synchronized to external unstable frequenciesHigh-G Rated:Suitable for application in high-G environments;operation tested to 100G, 10ms, 6-axes Fan Stop Function:Remotely switch off cooling fans to eliminate vibrationModel AX50 / AX100 / AX200Compact high-speed cameras with high light sensitivityProvided by: (800)404-ATECAdvanced Test Equipment Corp .®Rentals • Sales • Calibration • ServiceMonochrome sensors used in the FASTCAM Mini AX cameras are supplied without an IR absorbing filter, extending the camera spectral response beyod900nm. When the sensitivity of the FASTCAM Mini AX camera is measured to tungsten light including near IR response an equivalent value of ISO 100,000 is obtained.Image Sensor:The FASTCAM Mini AX system uses an advanced CMOS image sensor optimized for light sensitivity and high image quality that is unique to Photron.A 20-micron pixel pitch gives a sensor size at full image resolution of 20.48 x 20.48mm (diagonal 28.96mm). Lenses designed for both FX (35mm full frame) and also DX (APS-C digital SLR) formats are fully compatible with the FASTCAM Mini AX at full image resolution.High-Speed Gigabit Ethernet Interface:The FASTCAM Mini AX camera system is equipped with a high-speed Gigabit Ethernet Interface to provide reliable network communication and fast download of image data.Dedicated I/O:A dedicated BNC connection for a contact closure hardware trigger input is provided. In addition, two programmable inputs and two programmable output channels provide direct connection for common tasks such as synchronization of multiple cameras and operation in conjunction with Data Acquisition (DAQ) hardware.High-G Mechanical Calibration Shutter:The ruggedized mechanical shutter fitted as standard to the FASTCAM Mini AX camera allows sensor black balance calibration to be carried out remotely from the system control software.Nikon G-Type Compatible Lens Fitting:The FASTCAM Mini AX camera is equipped with an objective lens mount compatible with readily available Nikon G-type lenses. Controls provided within the lens mount allow the control of lens aperture on lenses without external iris control.ModelMini AX50Mini AX100Mini AX200 Full Frame Performance 2,000fps 1024 x 1024 pixels4,000fps 1024 x 1024 pixels 6,400fps 1024 x 1024 pixels Maximum Frame Rate Type 170K: 170,000fps (128 x 16 pixels)Type 200K: 212,500fps (128 x 16 pixels) Type 540K: 540,000fps* (128 x 16 pixels)Type 200K: 216,000fps (128 x 16 pixels) Type 540K: 540,000fps* (128 x 16 pixels)Type 900K: 900,000fps* (128 x 16 pixels)Minimum Exposure TimeInter Frame Time (for PIV)Ruggedized MechanicalCalibration ShutterDynamic Range (ADC) Memory Capacity Options Memory Partitions Region of Interest Trigger Inputs Trigger Delay Input / Output Trigger Modes Time Code Input External SyncCamera Control Interface Image Data Display Saved Image Formats Supported OSCamera BodySelectable +/- TTL 5V and switch closureProgrammable on selected input / output triggers: 100ns resolutionInput: Trigger (TTL/Switch), sync, ready, event, IRIG Output: trigger, sync, ready, rec, exposureStart, end, center, manual, random, random reset, image trigger, time lapse IRIG-B+/- TTL 5Vp-p Variable frequency sync High-speed Gigabit EthernetCamera Performance SpecificationsFrame rate, shutter speed, trigger mode, date/time, status, real time / IRIG time, frame count, resolutionBMP, TIFF, JPEG, PNG, RAW, RAWW, MRAW, AVI, WMV, FTIF, MOV - Images can be saved with or without image data and in 8-bit, 16-bit or 36-bit depth of sensor where supported* Frame rates above 225,000fps and exposure times below 1µs may be subject to export control regulations in some areasGlobal electronic shutter to 1.05µs selectable independent or frame rate (260ns option available with Mini AX200 type 900K only) *1.71µs 12-bit monochrome 36-bit color 8GB: 5,457 frames at full resolution 16GB: 10,918 frames at full resolution 32GB: 21,841 frames at full resolution Standard featureMicrosoft Windows operating system including: 7, 8, 8.1, 10 (32/64-bit)Up to 64 memory segmentsSelectable in steps of 128 pixels (horizontal) x 16 pixels (vertical)120mm (H) x 120mm (W) x 94mm (D)Frame Synchronization Accurate frame synchronization with other cameras and with external and unstable frequencies.Dual Slope Shutter(Extended Dynamic Range)Selectable in 20 steps (0 to 95% in 5% increments) to prevent pixel overexposure without post processing.Memory Partitions Up to 64 memory segments allow multiple events to be stored in camera memory before downloading, with automatic progression to the next available partition.Low Light Mode Operation at minimum frame rate with separately adjustable shutter time to allow easy camera set-up and focus in ambient lighting. IRIG Phase Lock Enables multiple cameras to be synchronized together with other instrumentation equipment or to a master external time source. Internal Time Delay Generator Allows programmable delays to be set on input and output triggers; 100ns resolution.Event Markers Up to ten user-entered event markers to define specific events within the recorded image sequence .Download While Recording FASTCAM Mini AX supports Partition Recording Mode, allowing image data captured in one memory partition to be downloaded while at the same time recording into another partition.Automatic Download The system can be set to automatically download image data to the control PC and, when download is complete to re-arm in readiness for the next trigger with automatically incremented file names.Software Binning Virtual pixel binning (2x2, 4x4 etc.) allows increased light sensitivity with reduced image resolution without changing camera field of view.Image Calibration 2D image calibration allows the measurement of distance and angle from the image. A calibration grid overlay can be superimposed on the image.Image Overlay A stored reference image may be overlaid on the live image to allow accurate camera positioning to achieve the same view as a previous test.Import of Multiple Image Sequences Multiple image sequences can be loaded and simultaneously replayed. Timing of image sequences can be adjusted to create a common time reference. Time based synchronization allows images captured at different frame rates to be synchronized.High Dynamic Range Mode Making use of the full sensor dynamic range, HDR mode allows enhanced detail in both light and dark areas of an image to be displayed simultaneously.Motion Detector In order to highlight subtle changes in an image, Motion Detector allows a reference image to be subtracted from a recorded sequence. Details including propagation of shock waves and surface changes during impact can be visualized using the feature.Line Profile A line profile representing grey levels along a line drawn across any region of the image is displayed. In live mode the Line Profile can be used to ensure optimum image focus is achieved.Histogram A histogram displaying grey levels within a user-defined image area is displayed. In live mode the Histogram can be used to ensure that optimum exposure levels are set for the scene being recorded.Operation Software FeaturesCamera Operation FeaturesPhotron FASTCAM Viewer:Photron FASTCAM Viewer software (PFV) has been designed to provide an intuitive and featurerich user interface for the control of Photron high-speed cameras, data saving, image replay andsimple motion analysis. Advanced operation menus provide access to features for advancedcamera operation and image enhancement. Tools are provided to allow image calibration andeasy measurement of angles and distances from image data. Also included are a C++ SDK andwrappers for LabView and MATLAB ®.An optional software plug-in module provides synchronisation between Photron high- speedcameras and data acquired through National Instruments data acquisition systems. Synchroniseddata captured by the DAQ system provides waveform information which can be viewed alongsidehigh-speed camera images.Photron FASTCAM Analysis:PFV software allows image sequences to be exported directly to optional Photron FASTCAMAnalysis (PFA) Motion Analysis software. This entry level Motion Analysis software with anon screen ‘step by step guide’ function launches automatically from Photron FASTCAM Viewersoftware, and provides automated tracking of up to 5 points using feature or correlation trackingalgorithms for the automated analysis of motion within an image sequence.Variable Region of Interest:Region of Interest (ROI) or sub-windowing allows a user-specified portion of the sensor to be defined to capture images. By using a reduced portion of the image area, the frame rate at which images are recorded can be increased. FASTCAM Mini AX allows the ROI to be set in increments of 128 pixels horizontal and 16 pixels vertical. Square Image Sensor Format:Unlike broadcast and media applications where image formats such as 16:9 have now become standard, in scientific and industrial imaging applications an image sensor with a 1:1 image format is generally accepted to be advantageous. To capture the maximum useful image data in applications including microscopy, detonics,combustion imaging and many others, a 1:1 sensor format provides greater flexibility than ‘letterbox’ image formats. The FASTCAM Mini AX image sensor allows the user to choose either square or rectangular image formats in order to obtain the maximum subject information.External Frame Synchronization:The FASTCAM Mini AX camera can be fully synchronized with an external event to allow the timing of when each individual image is captured to be precisely referenced. The camera can be accurately synchronized to unstable frequencies allowing complex events such ascombustion in rapidly accelerating or decelerating engines to be recorded and studied.Record During Download Operation:FASTCAM Mini AX recording memory can be divided into multiple active sections. The user can record an on-going event in one memory partition while at the same time downloading a previously recorded image sequence in order to improve workflow and optimize camera operation.Resolution Frame Rate(h x v pixels)Max fps Frames Time (sec)**Frames Time (sec)**Frames Time (sec)**1024 x 10246,4005,4570.8510,918 1.7121,841 3.411024 x 8967,2006,2360.8712,478 1.7324,961 3.47896 x 8968,1007,1270.8814,261 1.7628,527 3.52768 x 76810,8009,7010.9019,410 1.8038,829 3.60512 x 51222,50021,8290.9743,674 1.9487,365 3.88512 x 25643,20043,658 1.0187,349 2.02174,730 4.04256 x 25667,50087,317 1.29174,698 2.59349,461 5.18256 x 128120,000174,634 1.46349,397 2.91698,922 5.82128 x 128162,000349,269 2.16698,794 4.311,397,8458.63128 x 64259,200698,538 2.691,397,589 5.392,795,69010.79128 x 32360,0001,397,077 3.882,795,1787.765,591,38115.53128 x 16540,0002,794,1545.175,590,35710.3511,182,76220.71128 x 16900,000Resolution Frame Rate(h x v pixels)Max fps Frames Time (sec)**Frames Time (sec)**Frames Time (sec)**1024 x 10244,0005,457 1.3610,918 2.7321,841 5.461024 x 8964,5006,236 1.3912,478 2.7724,961 5.55896 x 8965,4007,127 1.3214,261 2.6428,527 5.28768 x 7686,8009,701 1.4319,410 2.8538,829 5.71512 x 51213,60021,829 1.6143,674 3.2187,365 6.42512 x 25625,50043,658 1.7187,349 3.43174,730 6.85256 x 25637,50087,317 2.33174,698 4.66349,4619.32256 x 12861,200174,634 2.85349,397 5.71698,92211.42128 x 12876,500349,269 4.57698,7949.131,397,84518.27128 x 64127,500698,538 5.481,397,58910.962,795,69021.93128 x 32170,0001,397,0778.222,795,17816.445,591,38132.89128 x 16540,0002,794,1545.175,590,35710.3511,182,76220.71Resolution Frame Rate(h x v pixels)Max fps Frames Time (sec)**Frames Time (sec)**Frames Time (sec)**1024 x 10242,0005,457 2.7310,918 5.4621,84110.921024 x 8962,5006,236 2.4912,478 4.9924,9619.98896 x 8962,5007,127 2.8514,261 5.7028,52711.41768 x 7683,6009,701 2.6919,410 5.3938,82910.79512 x 5127,20021,829 3.0343,674 6.0787,36512.13512 x 25613,60043,658 3.2187,349 6.42174,73012.85256 x 25620,40087,317 4.28174,6988.56349,46117.13256 x 12837,500174,634 4.66349,3979.32698,92218.64128 x 12845,900349,2697.61698,79415.221,397,84530.45128 x 6476,500698,5389.131,397,58918.272,795,69036.54128 x 32127,5001,397,07710.962,795,17821.925,591,38143.85128 x 16170,0002,794,15416.445,590,35732.8811,182,76265.78* Specifications subject to change without notice.** Recording time is an estimate and may be different depending on recording conditions and settings.8GB16GB32GBMini AX508GB16GB32GBMini AX2008GB16GB32GBMini AX100PhotoSchlieren imaging of fuel injection and engine combustion 20,000fpsMechanical Lens Mount Camera MountingsExternal DimensionsCamera Body(excluding protrusions)Weight Camera Body Environmental Operating Temperature Storage Temperature Humidity Cooling Operational Shock PowerAC Power (with supplied adapter)DC PowerMechanical and Environmental SpecificationsF-mount (G-type lens compatible) and C-mount provided - Optional lens mounts available include M42 adapter 4 x 1/4 - 20 UNC (base and top), 4 x M5 (base)120mm (H) x 120mm (W) x 94mm (D) 4.72" (H) x 4.72" (W) x 3.70" (D)1.5kg (3.30lbs)0 to 40C, 32˚ to 104˚F -20 to 60C, -4˚ to 140˚F 85% or less (non-condensing)Internal fan cooling (fan-off mode supported)100G, 10ms, 6-axes 100 to 240V, 50 to 60Hz 22 to 32V, 55VA allows the use of smaller objective lens apertures yielding greater depth of field and enhanced measurement of out of plane displacements. Small Physical Size:The small physical size and weight of the Mini camera range allows the use of conventional opto-mechanical hardware for rigid and stable mounting of multiple cameras, and for the location of cameras in space limited locations.Specifications subject to change without notice.PHOTRON USA, INC.9520 Padgett Street, Suite 110San Diego, CA 92126 USATel: 858.684.3555 or 800.585.2129Fax: 858.684.3558Email:*****************PHOTRON EUROPE LIMITED The Barn, Bottom RoadWest Wycombe, Bucks. HP14 4BS United KingdomTel: +44 (0) 1494 481011Fax: +44 (0) 1494 487011Email:***************** PHOTRON (Shanghai)Room 20C, Zhao-Feng World Trade Building No. 369, JiangSu Road ChangNing DistrictShanghai, 200050 China Tel: +86 (0) 21-5268-3700Email:***************.com PHOTRON LIMITED Kanda Jinbo-cho 1-105Chiyoda-ku, Tokyo 101-0051JapanTel: +81 (0) 3 3518-6271Fax: +81 (0) 3 3518-6279Email:****************.jp www.photron.co.jpREV# 17.03.03。
Hikvision DS-2DF8A842IXS-AEL(T5) 8 MP 42× IR Netwo
DS-2DF8A842IXS-AEL(T5)8 MP 42× IR Network Speed DomeHikvision DS-2DF8A842IXS-AEL(T5) 8MP 42× Network IR Speed Dome adopts 1/1.8" progressive scan CMOS chip. With the 42× optical zoom lens, the camera offers more details over expansive areas.This series of cameras can be widely used for wide ranges of high-definition, such as the rivers, forests, roads, railways, airports, ports, squares, parks, scenic spots, stations and large venues, etc.⏹1/1.8" Progressive Scan CMOS⏹High quality imaging with 8 MP resolution⏹Excellent low-light performance withPowered-by-DarkFighter technology⏹42× optical zoom and 16× digital zoom provide close up views over expansive areas⏹Expansive night view with up to 500 m IR distance⏹Water and dust resistant (IP67) and vandal proof (IK10)⏹Supports face capture to detect, capture, grade, and select faces in motion⏹Supports road traffic to detect vehicles⏹DORIThe DORI (detect, observe, recognize, identify) distance gives the general idea of the camera ability to distinguish persons or objects within its field of view.It is calculated based on the camera sensor specification and the criteria given by EN 62676-4: 2015.DORI Detect Observe Recognize IdentifyDefinition25 px/m63 px/m125 px/m250 px/m Distance (Tele)5040 m (16535.4 ft)2000 m (6561.7 ft)1008 m (3307.1 ft)504 m (1653.5 ft)⏹SpecificationCameraImage Sensor 1/1.8" progressive scan CMOSMin. Illumination Color: 0.005Lux @ (F1.2, AGC ON),B/W: 0.0005Lux @ (F1.2, AGC ON)Shutter Speed 1/1 s to 1/30,000 sSlow Shutter YesDay & Night IR cut filterZoom 42x optical, 16x digitalMax. Resolution 3840 × 2160LensFocus Auto, semi-auto, manual, rapid focusFocal Length 6.0 mm to 252 mmZoom Speed Approx. 4.8 sFOV Horizontal field of view: 56.6° to 1.7° (wide-tele), Vertical field of view: 33.7° to 0.9° (wide-tele), Diagonal field of view: 63.4° to 1.9° (wide-tele)Aperture Max. F1.2IlluminatorSupplement Light Type IRSupplement Light Range Up to 500 mSmart Supplement Light YesPTZMovement Range (Pan) 360°Movement Range (Tilt) -20° to 90° (auto flip)Pan Speed Pan speed: configurable from 0.1° to 210°/s; preset speed: 280°/s Tilt Speed Tilt speed: configurable from 0.1° to 150°/s, preset speed 250°/s Proportional Pan YesPresets 300Patrol Scan 8 patrols, up to 32 presets for each patrolPattern Scan 4 pattern scans, record time over 10 minutes for each scan Power-off Memory YesPark Action Preset, pattern scan, patrol scan, auto scan, tilt scan, random scan, frame scan, panorama scan3D Positioning Yes PTZ Status Display Yes Preset Freezing YesScheduled Task Preset, pattern scan, patrol scan, auto scan, tilt scan, random scan, frame scan, panorama scan, dome reboot, dome adjust, aux outputVideoMain Stream 50 Hz: 25 fps (3840 × 2160, 2560 × 1440, 1920 × 1080, 1280 × 960, 1280 × 720) 60 Hz: 30 fps (3840 × 2160, 2560 × 1440, 1920 × 1080, 1280 × 960, 1280 × 720)Sub-Stream 50 Hz: 25 fps (704 × 576, 640 × 480, 352 × 288) 60 Hz: 30 fps (704 × 480, 640 × 480, 352 × 240)Third Stream 50 Hz: 25 fps (1920 × 1080, 1280 × 960, 1280 × 720, 704 × 576, 640 × 480, 352 × 288) 60 Hz: 30 fps (1920 × 1080, 1280 × 960, 1280 × 720, 704 × 480, 640 × 480, 352 × 240)Video Compression Main stream: H.265+/H.265/H.264+/H.264 Sub-stream: H.265/H.264/MJPEGThird stream: H.265/H.264/MJPEGVideo Bit Rate 32 Kbps to 16384 KbpsH.264 Type Baseline Profile/Main Profile/High ProfileH.265 Type Main ProfileScalable Video Coding (SVC) H.264 and H.265 encodingRegion of Interest (ROI) 8 fixed regions for each streamAudioAudio Compression G.711alaw, G.711ulaw, G.722.1, G.726, MP2L2, PCMAudio Bit Rate 64 Kbps (G.711)/16 Kbps (G.722.1)/16 Kbps (G.726)/32 to 192 Kbps (MP2L2) NetworkNetwork Storage NAS (NFS, SMB/ CIFS), ANRProtocols IPv4/IPv6, HTTP, HTTPS, 802.1x, Qos, FTP, SMTP, UPnP, SNMP, DNS, DDNS, NTP, RTSP, RTCP, RTP, TCP/IP, DHCP, PPPoE, UDP, IGMP, ICMP, BonjourAPI ISUP, ISAPI, Hikvision SDK, Open Network Video Interface (Profile S, Profile G, Profile T) Simultaneous Live View Up to 20 channelsUser/Host Up to 32 users. 3 levels: Administrator, Operator and UserSecurity Password protection, complicated password, HTTPS encryption, 802.1X authentication (EAP-TLS, EAP-LEAP, EAP-MD5), watermark, IP address filter, basic and digest authentication for HTTP/HTTPS, RTP/RTSP over HTTPS, control timeout settings, security audit log, TLS 1.3, host authentication (MAC address)Client HikCentral, iVMS-4200, Hik-ConnectWeb Browser IE11, Chrome 57.0+, Firefox 52.0+, Safari 11+ ImageImage Settings Saturation, brightness, contrast, sharpness, gain, and white balance adjustable by client software or web browserDay/Night Switch Day, night, auto, scheduled-switchImage Enhancement BLC, HLC, 3D DNRWide Dynamic Range (WDR) 140 dB WDRDefog Optical defogImage Stabilization Yes. Built-in gyroscope to improve EIS performanceRegional Exposure YesRegional Focus YesPrivacy Mask Up to 24 masks, polygon region, mosaic mask, mask color configurable SNR ≥ 52 dBSupplement DetectionSatellite Positioning YesInterfaceEthernet Interface 1 RJ45 10M/100M self-adaptive Ethernet portOn-board Storage Built-in memory card slot, support MicroSD/MicroSDHC/MicroSDXC, up to 256 GB Alarm 7 inputs, 2 outputsAudio 1 input (line in), max. input amplitude: 2-2.4 vpp, input impedance: 1 KΩ ± 10%; 1 output (line out), line level, output impedance: 600 ΩVideo Output 1.0V[p-p]/75Ω, PAL, NTSC, BNC connectorRS-485 HIKVISION, Pelco-P, Pelco-D, self-adaptiveEventBasic Event Motion detection, video tampering alarm, alarm input and output, exceptionSmart Event Line crossing detection, region entrance detection, unattended baggage detection, object removal detection, intrusion detection, region exiting detection, vandal-proof alarm, audio exception detectionSmart Tracking Manual tracking, auto-trackingAlarm Linkage Alarm actions, such as Preset, Patrol Scan, Pattern Scan, Memory Card Video Record, Trigger Recording, Notify Surveillance Center, Upload to FTP/Memory Card/NAS, Send Email, etc.Deep Learning FunctionFace Capture Support detecting up to 30 faces at the same time. Support detecting, tracking, capturing, grading, selecting of face in motion, and output the best face picture of the faceFace Comparison YesPerimeter Protection Line crossing, intrusion, region entrance, region exitingSupport alarm triggering by specified target types (human and vehicle)Road Traffic and Vehicle DetectionRoad Traffic Support vehicle detection (license plate number,vehicle model, and vehicle color recognition)GeneralGeneral Function Mirror, password protection, watermark, IP address filterPower 24 VAC (Max. 60 W, including max. 18 W for IR and max. 6 W for heater), Hi-PoE (Max.50 W, including max. 18 W for IR and max. 6 W for heater)Operating Condition Temperature: -40°C to 70°C (-40°F to 158°F), Humidity: ≤ 95% Dimension ⌀ 267 mm × 405 mm (⌀ 10.51" × 15.94")Weight Approx. 8.5 kg (18.74 lb.)Language 33 languages: English, Russian, Estonian, Bulgarian, Hungarian, Greek, German, Italian, Czech, Slovak, French, Polish, Dutch, Portuguese, Spanish, Romanian, Danish, Swedish, Norwegian, Finnish, Croatian, Slovenian, Serbian, Turkish, Korean, Traditional Chinese, Thai, Vietnamese, Japanese, Latvian, Lithuanian, Portuguese (Brazil), UkrainianApprovalEMCFCC SDoC (47 CFR Part 15, Subpart B);CE-EMC (EN 55032: 2015, EN 61000-3-2: 2019, EN 61000-3-3: 2013+A1:2019, EN50130-4: 2011 +A1: 2014); RCM (AS/NZS CISPR 32: 2015); IC VoC (ICES-003: Issue 7); KC (KN 32: 2015, KN 35: 2015) SafetyUL (UL 62368-1)CB (IEC 62368-1:2014+A11);CE-LVD (EN 62368-1:2014+A11:2017),BIS (IS 13252(Part 1):2010/ IEC 60950-1: 2005); LOA (IEC/EN 60950-1)Environment CE-RoHS (2011/65/EU); WEEE (2012/19/EU); Reach (Regulation (EC) No 1907/2006)ProtectionLightning Protection, Surge Protection and Voltage Transient Protection, ±6 kV Line to Gnd, ±3kV Line to Line, IK10 (IEC 62262:2002), IP67 (IEC 60529-2013)⏹Typical ApplicationHikvision products are classified into three levels according to their anti-corrosion performance. Refer to the following description to choose for your using environment.This model has NO SPECIFIC PROTECTION.LevelDescriptionTop-level protectionHikvision products at this level are equipped for use in areas where professional anti-corrosion protection is a must. Typical application scenarios include coastlines, docks, chemical plants, and more.Moderate protectionHikvision products at this level are equipped for use in areas with moderate anti-corrosion demands. Typical application scenarios include coastal areas about 2 kilometers (1.24 miles) away from coastlines, as well as areas affected by acid rain.No specific protectionHikvision products at this level are equipped for use in areas where no specific anti-corrosion protection is needed.⏹Available ModelDS-2DF8A842IXS-AEL (T5)⏹Dimension⏹Accessory ⏹OptionalDS-1604ZJ-Corner-P Corner mountDS-1682ZJ-PPendant MountDS-1604ZJ-BOX-POLE-PVertical polemountDS-1604ZJ-BOX-PWall mountDS-1673ZJ-PVertical polemountDS-1662ZJ-P Pendant MountDS-1667ZJ-PPendant MountDS-1660ZJ-PWall mountDS-1604ZJ-Pole-PVertical polemountDS-1661ZJ-PPendant MountDS-1604ZJ-P Wall mount DS-1604ZJ-BOX-CORNER-PWall mountDS-1663ZJ-PIn-ceiling mount。