手表行业术语中英对照表
钟表中英文对照术语表
钟表中英文对照术语表，希望对各位表迷有所帮助10J — 10天动力储备Abbreviation for 10 days power reserve in the Patek Philippe typology。
在百达翡丽而言是“10 days power reserve - 10天动力储备”的缩写.24H — 24小时表盘Abbreviation for ”24—hour dial”，in the Patek Philippe typology。
在百达翡丽而言是“24—hour dial — 24 小时表盘"的缩写.Amplitude —摆幅Measurement in degrees of the movement of a balance and spring assembly：amplitude is the angle between the position of equilibrium and its maximum elongation.测量摆轮游丝装置的摆动角度：摆幅即是游丝装置的平衡位置与最大距角之间的角度。
Analogue —指针式时间显示Refers to time display using hands.指采用指针来显示时间.Aperture —视窗、孔径Dial opening revealing the indications provided on discs rotating under the dial.表盘上的开孔，可看见表盘下的转盘的显示信息。
Applique - 镶刻Raised numeral or hour-marker, applied to or riveted to the dial. At Patek Philippe，appliques are always in gold and are sometimes diamond-set.固定在表盘上的凸起数字或时间刻度。
钟表中英文对照术语表
钟表中英文对照术语表，希望对各位表迷有所帮助10J - 10天动力储备Abbreviation for 10 days power reserve in the Patek Philippe typology.在百达翡丽而言是“10 days power reserve - 10天动力储备”的缩写。
24H - 24小时表盘Abbreviation for "24-hour dial", in the Patek Philippe typology.在百达翡丽而言是“24-hour dial - 24 小时表盘”的缩写。
Amplitude - 摆幅Measurement in degrees of the movement of a balance and spring assembly: amplitude is the angle between the position of equilibrium and its maximum elongation.测量摆轮游丝装置的摆动角度：摆幅即是游丝装置的平衡位置与最大距角之间的角度。
Analogue - 指针式时间显示Refers to time display using hands.指采用指针来显示时间。
Aperture - 视窗、孔径Dial opening revealing the indications provided on discs rotating under the dial.表盘上的开孔，可看见表盘下的转盘的显示信息。
Applique - 镶刻Raised numeral or hour-marker, applied to or riveted to the dial. At Patek Philippe, appliques are always in gold and are sometimes diamond-set.固定在表盘上的凸起数字或时间刻度。
钟表中英文对照术语表
钟表中英文对照术语表,希望对各位表迷有所帮助10J — 10天动力储备Abbreviation for 10 days power reserve in the Patek Philippe typology。
在百达翡丽而言是“10 days power reserve — 10天动力储备”的缩写。
24H — 24小时表盘Abbreviation for ”24—hour dial”，in the Patek Philippe typology.在百达翡丽而言是“24—hour dial - 24 小时表盘”的缩写.Amplitude - 摆幅Measurement in degrees of the movement of a balance and spring assembly：amplitude is the angle between the position of equilibrium and its maximum elongation.测量摆轮游丝装置的摆动角度:摆幅即是游丝装置的平衡位置与最大距角之间的角度.Analogue - 指针式时间显示Refers to time display using hands.指采用指针来显示时间。
Aperture —视窗、孔径Dial opening revealing the indications provided on discs rotating under the dial。
表盘上的开孔，可看见表盘下的转盘的显示信息。
Applique - 镶刻Raised numeral or hour-marker，applied to or riveted to the dial. At Patek Philippe，appliques are always in gold and are sometimes diamond—set.固定在表盘上的凸起数字或时间刻度。
手表行业术语中英对照表
手表行业术语中英对照表(总10页) -本页仅作为预览文档封面，使用时请删除本页-计时码表(Chronograph watch)自动表(Automatic Watch)跳字行针表(Analogical Digital Watch)2>表壳壳胚(Blank)玻璃(Glass、lens)普通玻璃(Mineral Glass)蓝宝石玻璃（Sapphire Glass）半蓝宝石玻璃(Semi-sapphire glass)I令(I ring)霸的（表冠）(Crown)霸的管（Crown Tube）按的(Pusher)壳圈（Bezel）分圈(Top Ring)锑片(Aluminium foil)内罩(Movement Holder)底盖(Case Back)铜底盖(S/S case back)透视底盖(See-through case back)锁底盖(Screw back)O令(O-ring)(Gasket)生耳/钢闩（End-piece/pin）3>表壳打磨拉沙（Hair Brushed）12/6H方向直沙(912/6H vertical brushed)3/9H方向横沙(3/6H horizontal brushed)圆沙(Circle brushed)喷沙(Fine Sand Blasted)光令（Satin/Polish）壳:Case表胚：watch blank表圈：watch bezel表面：dial晌圈：springed metal ring内影：metal case decoratiue ring不锈钢实心表带：stainless steel semi-solid band 包边带：side-wrapped band包边不锈钢表带：side-wrapped stainless steel band 织网表带：mesh band芯片：chip钨钢：tungsten steel皮表带：leather strap皮带扣：buckle forstap霸的：crown霸管：crown tube霸芯及驳管：stem and stem extension胶内影：housing/movement holder蓝宝石玻璃：sapphire crystal普通玻璃：ordinary glass凸晶玻璃：eye glass底盖：back cover生耳：spring bar生耳杆：T-bars with studs orscrews拆生钢枝：s/s pins and shafts拆生锣丝：removable screwed pin搓花钢枝：s/s knurled pins弹簧扣：spring buckel龟壳扣：clasps蝴蝶扣：folding clasps /butterfly style buckle鸭嘴扣：duck-mouth buckle圆头饰钉：cabochon机芯：movement移印：padprinting吸塑包装：blister&packaging真空镀膜：vacuum coating蚀麦：etchedtrade mark單卜:dome len雙卜:curved len一、仕样不光边no polishing.['pɔliʃ]幼砂fine sand太阳砂radiation brushing.[reidi'eiʃən]打字stamped.[stæmp]光令mirror finishing光滑表面smooth surface光边polishing光边直砂6—12polished brushing光边圆砂circular polished brushing防水度water-resistant level直砂6-12 brushing砂纹sand brushing涂油add grease .[ɡri:s]镀黑black chrome plating .[krəʊm]填黑油black filled鱼鳞纹armor brushing.['ɑ:mə]圆砂circular brushing蚀字chemical etching .['etʃɪŋ]喷砂sand brushing横砂3-9brushing镭射字体laser二、表面（Dial）分位字尾minute struck日历窗date frame .[freim]字印marking字钉index.['indeks表面surface表面加工ackground finishing面底色background color面厚 dial thickness面窗dial ring时位字尾hour struck牌子名brand name点dot镶唛applied logo钻石diamond钻石托diamond bushings三、表针（Hand）山型顶faceted分针minute hand平顶 flat百分秒针chromo second hand .['krəuməu] 夜光luminous .['lu:minəs]表针hand秒针second hand针高hand height四、底盖（Caseback）刀口位opening slot内字印inside marking外字印outside marking波子底back snap底保护贴back protective sticker .['stikə]底匙眼back key slot底盖caseback螺丝screw螺丝牙screw thread .[θred]米底 point snap湾形底curved caseback .[kə:v]五、表带（caseband /wristket /band）中珠center link皮带strap/leather皮带扣利口tongue皮带环loop扣制buckle ['bʌkl]尾珠end piece拆生珠removable link/adjustable link表带caseband /wristket /band潜水扣dive buckle单接皮带扣deploy .[di'plɔi]边珠side link实心珠solid link珠宝扣jewellery buckle蝴蝶扣butterfly buckle双开蝴蝶扣hidden butterfly pushed button 头珠starting piece箭咀arrow .['ærəu]六、配件电池battery螺丝的头screw crown螺钉screw pin螺丝耳杆 screw spring bar单胶圈的头single o-ring crown双胶圈的头double o-ring crown按的 push button八角线octagon thread .['ɔktə,gɔn]八角形的octagon六角形的 hexagon填夜光油luminous filled机芯movement实配机芯casing针pin软O-Ring soft o-ring硬o-ring rigid o-ring软胶I令soft plastic I-ring硬胶I令 rigid I-ring白色I令white I-ring半透明I令semi-transparent I-ring发夹hair pin贴纸tape双面胶double side tape大头针friction pin字母通capsa pin-pipe（tube）压罩compression on holder[kəm'preʃən] 内罩movement holder螺丝巴管screw tubeT行巴管T-tube巴芯stem湾生耳banded spring bar生耳spring bar无托生耳free stand spring bar单托生耳single stand spring bar双托生耳dual stand spring bar ['dju:əl] 平头连斜巴flat head with chamfer平头巴的flat head圆头巴的round headT形巴的T-crown丝印玻璃silk screen glass镀膜玻璃plating glass单卜玻璃one side curved glass双卜玻璃both side curved glass蓝宝石水晶sapphire crystal .['sæf,aɪə] 玻璃glass白板玻璃mineral glass水晶玻璃crystal glass七、组立（装配）不防水water proof failed不动formfit加防水油add silicon oil半跌half drop全跌full drop玻璃不配壳glass not fitting on case装配 assembly配合fitting配带caseband fitting壳带配合不良poor fitting for case band 八、性能（function）拉力pull force顶力retention force.[ri'tenʃən]横拉力horizontal pull force .[,hɔri'zɔntəl] 防水测试不合格water test failed防潮 water resist退return九、结构面平flat surface镶石圈stone top ringO-ring 坑 o-ring ditch/ groove刀口位开在opening notch at .[nɔtʃ]刀口位opening slot大身3-9case side wall大身面3-9case surface细身面6-12case surface细身6-12case side wall开面opening开粗roughing内耳款inner lug width内映reflector买内影圈erflector ring丝吼inside diameter .[dai'æmitə]圈bezel弹珠结构ball structure止口高position for snap胶水glue展开长度open-up length压缩长度compressed length外耳款outer lug width避针为hand clearance夜光luminescent顶圈top ring壳耳case lug单卜upper curve bottom .[kə:v] 石拓stone bushing巴孔crown opening圆壳round case方壳square case异形壳irregular case底平flat bottom企身为standing point字深= of text=有电池托w/battery strop没电池托w/o battery strop耳长lug diameter叉耳fork legs耳吼lug hole耳底lug case耳面lug surface耳脚 lug stand耳款lug width检验尺寸inspection size加工尺寸production size按的位position for push button 玻璃位glass position石爪prong假螺钉decorating screw十、缺陷不足够insufficient [ɪnsə'fɪʃənt] 磨罍over polishing电镀不良poor plating车线不良poor stitching ['stitʃiŋ] 污物dirts利边sharp edge批锋burr.[bɜ:]甩字钉index fall out松loose花scratched表面脱色dial discolor欠缺missing出问题found problems打磨不良poor polishing砂孔sand hole砂过界over brushing打磨错误wrong polishing突出protruded.[prəʊ'tru:d]振刀纹rough turning mark氧化斑点oxidize spot.['ɔksɪ,daɪz] 破裂crack起泡bubble崩dented脱落come off倾斜poor printing损坏damaged紧tight轻胶水过多excessive glue断裂broken蜡屎wax严重major变形deformed十一、其它反面图reversed view正常normal名称title制图drafter注意打磨caution on finishing待定玻璃外围尺寸outer glass diameter要点remark规格format标准/正规standard检查/签名checker进出口import/export时装表fashion watch经典表classic watch运动表sports watch女/男装women/man model女/男装lady /gents model童装kids watch电子表digital watch日本/瑞士机芯Japan or Swiss movement 日本石英Japan quartz唛头logo/marking士啤spare parts大/小尺寸big/small size抛光polishing/shiny电镀plating防水water resistant功能function皮料/色卡material collection目录catalogue/catalog参考reference附上的附件attached/attachment图片/相片picture/photo方形/圆形square/round shaped椭圆oval .['əuvəl]有/无按的with/ without pusher产品/生产production/product彩图colourful drawing表面设计 dial design确认/再次确认 conform/double confirm 取消/保留 cancel/keep订单 order翻单 repeat order新订单new order新款 new model原始订单 original order同样板一样same as sample样品 sample出货样shipment sample确认样approval sample假版dummy sample .['dʌmi:]包装 packing装箱单packing list发票invoice毛重/净重gross or net weight艺术字 artwork单词/字母，信 word /letter纸盒paper box 小贴纸small sticker标签label吊牌hangtagPP胶袋 polybag气泡袋 bubble bag间电tow-tone透明的transparent多功能计时 chrono。
(完整版)钟表专业术语全(精)
钟表专业术语（英/法/德/意）Alarm (Réveil/Wecker/Sveglia)响闹腕表表壳上具有两只表冠，其中一只可以设定响闹时间，到时就会由一支以高速振动的小锤敲响表壳的后盖提醒时间已到Antimagnetic (Antimagnétique/Antimagnetisch/Antimagnetico)防磁机械表机芯最重要的机构是摆轮游丝系统，如果它受到磁力的影响势必会产生走时的误差，人们很早的时候便开始寻找解决的办法，目前普遍使用的是非磁性的摆轮和游丝，它们分别采用铍青铜和镍合金等制成，具有抗磁的性能。
一般防磁的标准是4800A/mApplique (Applique/Auflage/Aplique)镶字块用金属冲压而成的刻度标记，主要铆压在表盘上Assemble (Remonter/Zusammensetzen/Montar)装配把钟表机芯的各种零部件组合在一起的工序Atmos (Atmos/Atmos/Atmós)空气钟1928年，工程师Jean-Léon Reutter发明了凭借空气动力驱动的时钟，其原理是在一个完全密封的容器内充满气体，根据温度的变化导致气体的膨胀或收缩、产生持续的动力，在摄氏15—30度范围内，只要一度的变化就会提供48小时的运转能量Amplitude (Amplitude/Schwingungsweite/Amplitud)摆幅手表摆轮旋转的角度大小，一般在180－315度之间Automatic (Automatique/Automatisch/Automático)自动依靠人体手臂的活动，通过内置在机芯的自动装置使手表发条上紧Automation (Automation/Automation/Automación)自动人偶能够产生不同动作的自动人偶，在早期钟表制作中经常出现，主要是凭借机械动力来源，通过精密的传动机构而完成Balance (Balancier/Unruh/Bilanciere)摆轮产生振荡作用的调速机构的主要零件之一Balance-cock (Coq/Unruhkloben/Coq)摆轮夹板固定摆轮起到支撑作用的金属零件Balance-spring (Spiral/Spiralfeder/Spirale)摆轮游丝使摆轮产生回复旋转作用的金属丝Barrel (Barillet/Federhaus/Bariletto)条盒轮由发条直接驱动的齿轮Barrel-arbor (Arbre de barillet/Federwelle/Albero del bariletto）条轴发条所环绕的金属轴，能够起到固定发条的一端的作用Bezel (Lunette/Lünette/Lunette)外圈固定表玻璃的零部件，主要起到装饰和实用的双重作用Bimetallic (Bimétallique/Zweimetallisch/Bimetálico)双金属利用铜和钢两种材质对于温度的不同膨胀系数，使温差变化对于机械钟表产生的影响改变，早期主要运用于摆轮的制造Bevel (Biseau/Abschrcgung/Bisel)倒角对于机芯零部件的边角进行人手打磨的工序Brass (Laiton/Messing/Ottone)黄铜含有30%-40%锌成分的铜与锌的合金，主要用于制造主夹板、夹板、轮列和表壳等。
手表行业术语中英对照表
成表配件中英文对照1>成表(Completed Watch)石英表(Quartz Watch)计时码表(Chronograph watch)自动表(Automatic Watch)跳字行针表(Analogical Digital Watch) 2>表壳壳胚(Blank)玻璃(Glass、lens)普通玻璃(Mineral Glass)蓝宝石玻璃（Sapphire Glass）半蓝宝石玻璃(Semi-sapphire glass)I令(I ring)霸的（表冠）(Crown)霸的管（Crown Tube）按的(Pusher)壳圈（Bezel）分圈(Top Ring)锑片(Aluminium foil)内罩(Movement Holder)底盖(Case Back)铜底盖(S/S case back)透视底盖(See-through case back)锁底盖(Screw back)O令(O-ring)(Gasket)生耳/钢闩（End-piece/pin）3>表壳打磨拉沙（Hair Brushed）12/6H方向直沙(912/6H vertical brushed) 3/9H方向横沙(3/6H horizontal brushed) 圆沙(Circle brushed)喷沙(Fine Sand Blasted)光令（Satin/Polish）壳:Case表胚：watch blank晌圈：springed metal ring内影：metal case decoratiue ring不锈钢实心表带：stainless steel semi-solid band包边带：side-wrapped band包边不锈钢表带：side-wrapped stainless steel band 织网表带：mesh band芯片：chip钨钢：tungsten steel皮表带：leather strap皮带扣：buckle forstap霸的：crown霸管：crown tube霸芯及驳管：stem and stem extension胶内影：housing/movement holder蓝宝石玻璃：sapphire crystal普通玻璃：ordinary glass凸晶玻璃：eye glass底盖：back cover生耳：spring bar生耳杆：T-bars with studs orscrews拆生钢枝：s/s pins and shafts拆生锣丝：removable screwed pin搓花钢枝：s/s knurled pins弹簧扣：spring buckel龟壳扣：clasps蝴蝶扣：folding clasps /butterfly style buckle鸭嘴扣：duck-mouth buckle圆头饰钉：cabochon机芯：movement移印：padprinting吸塑包装：blister&packaging真空镀膜：vacuum coating蚀麦：etchedtrade mark單卜:dome len不光边no polishing.['pɔliʃ]幼砂fine sand太阳砂radiation brushing.[reidi'eiʃən] 打字stamped.[stæmp]光令mirror finishing光滑表面smooth surface光边polishing光边直砂6—12polished brushing光边圆砂circular polished brushing 防水度water-resistant level直砂6-12 brushing砂纹sand brushing涂油add grease .[ɡri:s]镀黑black chrome plating .[krəʊm] 填黑油black filled鱼鳞纹armor brushing.['ɑ:mə]圆砂circular brushing蚀字chemical etching .['etʃɪŋ]喷砂sand brushing横砂3-9brushing镭射字体laser二、表面（Dial）分位字尾minute struck日历窗date frame .[freim]字印marking字钉index.['indeks表面surface表面加工ackground finishing面底色background color面厚dial thickness面窗dial ring时位字尾hour struck牌子名brand name点dot钻石diamond钻石托diamond bushings三、表针（Hand）山型顶faceted分针minute hand平顶flat百分秒针chromo second hand .['krəuməu] 夜光luminous .['lu:minəs]表针hand秒针second hand针高hand height四、底盖（Caseback）刀口位opening slot内字印inside marking外字印outside marking波子底back snap底保护贴back protective sticker .['stikə] 底匙眼back key slot底盖caseback螺丝screw螺丝牙screw thread .[θred]米底point snap湾形底curved caseback .[kə:v]五、表带（caseband /wristket /band）中珠center link皮带strap/leather皮带扣利口tongue皮带环loop扣制buckle ['bʌkl]尾珠end piece拆生珠removable link/adjustable link表带caseband /wristket /band潜水扣dive buckle单接皮带扣deploy .[di'plɔi]边珠side link珠宝扣jewellery buckle蝴蝶扣butterfly buckle双开蝴蝶扣hidden butterfly pushed button 头珠starting piece箭咀arrow .['ærəu]六、配件电池battery螺丝的头screw crown螺钉screw pin螺丝耳杆screw spring bar单胶圈的头single o-ring crown双胶圈的头double o-ring crown按的push button八角线octagon thread .['ɔktə,gɔn]八角形的octagon六角形的hexagon填夜光油luminous filled机芯movement实配机芯casing针pin软O-Ring soft o-ring硬o-ring rigid o-ring软胶I令soft plastic I-ring硬胶I令rigid I-ring白色I令white I-ring半透明I令semi-transparent I-ring发夹hair pin贴纸tape双面胶double side tape大头针friction pin字母通capsa pin-pipe（tube）压罩compression on holder[kəm'preʃən] 内罩movement holder螺丝巴管screw tubeT行巴管T-tube湾生耳banded spring bar生耳spring bar无托生耳free stand spring bar单托生耳single stand spring bar双托生耳dual stand spring bar ['dju:əl] 平头连斜巴flat head with chamfer平头巴的flat head圆头巴的round headT形巴的T-crown丝印玻璃silk screen glass镀膜玻璃plating glass单卜玻璃one side curved glass双卜玻璃both side curved glass蓝宝石水晶sapphire crystal .['sæf,aɪə] 玻璃glass白板玻璃mineral glass水晶玻璃crystal glass七、组立（装配）不防水water proof failed不动formfit加防水油add silicon oil半跌half drop全跌full drop玻璃不配壳glass not fitting on case装配assembly配合fitting配带caseband fitting壳带配合不良poor fitting for case band 八、性能（function）拉力pull force顶力retention force.[ri'tenʃən]横拉力horizontal pull force .[,hɔri'zɔntəl] 防水测试不合格water test failed防潮water resist退return面平flat surface镶石圈stone top ringO-ring 坑o-ring ditch/ groove刀口位开在opening notch at .[nɔtʃ] 刀口位opening slot大身3-9case side wall大身面3-9case surface细身面6-12case surface细身6-12case side wall开面opening开粗roughing内耳款inner lug width内映reflector买内影圈erflector ring丝吼inside diameter .[dai'æmitə] 圈bezel弹珠结构ball structure止口高position for snap胶水glue展开长度open-up length压缩长度compressed length外耳款outer lug width避针为hand clearance夜光luminescent顶圈top ring壳耳case lug单卜upper curve bottom .[kə:v]石拓stone bushing巴孔crown opening圆壳round case方壳square case异形壳irregular case底平flat bottom企身为standing point字深=0.5depth of text=0.50没电池托w/o battery strop耳长lug diameter叉耳fork legs耳吼lug hole耳底lug case耳面lug surface耳脚lug stand耳款lug width检验尺寸inspection size加工尺寸production size按的位position for push button 玻璃位glass position石爪prong假螺钉decorating screw十、缺陷不足够insufficient [ɪnsə'fɪʃənt] 磨罍over polishing电镀不良poor plating车线不良poor stitching ['stitʃiŋ] 污物dirts利边sharp edge批锋burr.[bɜ:]甩字钉index fall out松loose花scratched表面脱色dial discolor欠缺missing出问题found problems打磨不良poor polishing砂孔sand hole砂过界over brushing打磨错误wrong polishing突出protruded.[prəʊ'tru:d]振刀纹rough turning mark氧化斑点oxidize spot.['ɔksɪ,daɪz]起泡bubble崩dented脱落come off倾斜poor printing损坏damaged紧tight轻微minor胶水过多excessive glue断裂broken蜡屎wax严重major变形deformed十一、其它反面图reversed view正常normal名称title制图drafter注意打磨caution on finishing待定T.B.A玻璃外围尺寸outer glass diameter要点remark规格format标准/正规standard检查/签名checker进出口import/export时装表fashion watch经典表classic watch运动表sports watch女/男装women/man model女/男装lady /gents model童装kids watch电子表digital watch日本/瑞士机芯Japan or Swiss movement 日本石英Japan quartz唛头logo/marking大/小尺寸big/small size抛光polishing/shiny电镀plating防水water resistant功能function皮料/色卡material collection目录catalogue/catalog参考reference附上的附件attached/attachment图片/相片picture/photo方形/圆形square/round shaped椭圆oval .['əuvəl]有/无按的with/ without pusher产品/生产production/product彩图colourful drawing表面设计dial design确认/再次确认conform/double confirm 取消/保留cancel/keep订单order翻单repeat order新订单new order新款new model原始订单original order同样板一样same as sample样品sample出货样shipment sample确认样approval sample假版dummy sample .['dʌmi:]包装packing装箱单packing list发票invoice毛重/净重gross or net weight艺术字artwork单词/字母，信word /letter纸盒paper box小贴纸small sticker标签label吊牌hangtagPP胶袋polybag 气泡袋bubble bag 间电tow-tone透明的transparent 多功能计时chrono。
世界手表专业词汇中英文对照
钢Steel显示Display手工组装Hand-fitting手工Hand调节Fit, adjust振动Vibration避震装置Shock-absorber擒纵叉Pallets防震Shock-resistant防磁Antimagnetic防尘Dustproof立体时标，刻度Applique条轴Barrel-arbor银质，镀银Silver, silver-plate轮（和齿轮）Wheel (and pinion) 自动上链Self-winding, automatic 蜗形花纹Snailed摆轮Balance发条盒Barrel杆Bar, lug倒角Bevel表扣Buckle表壳Watch-case表带Wristlet手镯，手镯型Bangle指针Arm夹具Clamp环状凸缘Flange, collar圆头饰钉Cabochon表盘，面盘Dial万年历Perpetual calendar机芯Calibre, caliber凹槽，（表冠周围或表壳侧边的）凹凸纹路Flute 时轮Hour-wheel克拉Carat铆压（将表钻压入位置）Driving镶嵌（宝石）Setting分轮Cannon-pinion计时表Chronograph精密时计，天文台时计Chronometer集成电路Integrated circuit同轴Coaxial混合Combo复杂功能Complication读数器，计数器，计时器Register, Coanter, timer 摆轮夹板Balance-cock表耳表壳与表带连接处Horn弯曲Curved表冠Crown陶瓷Ceramics跳日期型Jumping date烫金Gild分离器Disconnecting-gear传送Transfer展示盒Presentation-case机电式Electromechanically珐琅工艺Enamel离合，连接Clutch宝石，镶宝石Jewel棘轮结构Click齿轮结构Gear定位销，销钉Catch防水Water-resistant密封性，防水性Sealing超薄型Extra-flat表扣，搭扣Clasp打磨，抛光Finishing酒桶形Tonneau shaped擒纵叉Fork制表材料Watch-material摩擦Friction均力圆锥轮Fusee表玻璃Glass, crystal平衡摆轮Glucydur圭表，日晷Gnomon铰链Hinge视窗Aperture饰纹Engine-turn小时，时间Hour, time跳时显示Jumping hour钟表Clock脉冲Impulse指示器，包括表盘、指针、刻度等Indicator防刮擦Scratch-resistant黄铜（含有30%-40%锌成分的铜与锌的合金）Brass 叉杆Lever夜光Luminescence产品，工厂Works, factory音锤Hammer微米Micron走针机构Motion-work轮Wheel单钮Single button表Watch手表Wristwatch机芯Movement机制，结构Mechanism 金，黄金Gold摆动，震荡Oscillation擒纵叉瓦Pallet-stone钟摆装置Pendulum宝石轴承Stone jewel齿轮Pinion枢轴Pivot压电体Piezoelectric镀层，镀膜，镶贴Platting 铂金Platinum饰钉Stud印记hallmark,stamp打磨，抛光Polish夹板，表桥Bridge按钮Push-piece，push-button芯片Chip揿钉Punaise日期Date石英Quartz刻度Index分段计时Split-seconds飞返Fly back上弦装置，上链装置winding-mechanism 拨针轮Intermediate wheel发条，弹簧Spring金属镀层Metal coating维修，修理Repair棘轮Ratchet转子，转轮Rotor齿轮Geartrain轮片Wheel红宝石（轴承）Ruby调校Regulation, setting调校表，标准时计Regulator打簧报时表，问表Repeater三问报时Minute repetiting两问报时Quarter repeater动力储存Power reserve闹响，闹铃Alarm跳跃式Jumping猎人表Hunter watch秒，秒针Seconds中央秒针，大秒针center seconds小秒针表盘Auxiliary seconds dial镶嵌Set（a gem）报时装置Striking-mechanism游丝Spiral镂空Skeleton测速计Tachymeter叉销Bolt倒计时调谐器Countdown tuner法定时间Legal time格林威治标准时间(GMT) Greenwich Mean Time (GMT) 世界时(UT) Universal Time (UT)装配和修饰Assembling and finishing音簧Gong陀飞轮Tourbillion防护盖Hatch cover微调电容Trimmer氚Tritium秒针Second hand叉销，栓Bolt锌Zinc未加工机芯，半成品机芯Movement-blank, ebauche 擒纵结构Escapement压模，锻模Press-tool。
钟表中英文对照术语表
钟表中英文对照术语表，希望对各位表迷有所帮助10J - 10天动力储备Abbreviation for 10 days power reserve in the Patek Philippe typology。
在百达翡丽而言是“10 days power reserve - 10天动力储备”的缩写。
24H - 24小时表盘Abbreviation for ”24—hour dial”, in the Patek Philippe typology。
在百达翡丽而言是“24-hour dial — 24 小时表盘”的缩写。
Amplitude —摆幅Measurement in degrees of the movement of a balance and spring assembly: amplitude is the angle between the position of equilibrium and its maximum elongation.测量摆轮游丝装置的摆动角度：摆幅即是游丝装置的平衡位置与最大距角之间的角度。
Analogue - 指针式时间显示Refers to time display using hands。
指采用指针来显示时间。
Aperture - 视窗、孔径Dial opening revealing the indications provided on discs rotating under the dial.表盘上的开孔,可看见表盘下的转盘的显示信息。
Applique - 镶刻Raised numeral or hour—marker，applied to or riveted to the dial。
At Patek Philippe，appliques are always in gold and are sometimes diamond-set。
固定在表盘上的凸起数字或时间刻度。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
跳字行针表(Analogical Digital Watch)2>表壳壳胚(Blank)玻璃(Glass、lens)普通玻璃(Mineral Glass)蓝宝石玻璃（Sapphire Glass）半蓝宝石玻璃(Semi-sapphire glass)I令(I ring)霸的（表冠）(Crown)霸的管（Crown Tube）按的(Pusher)壳圈（Bezel）分圈(Top Ring)锑片(Aluminium foil)内罩(Movement Holder)底盖(Case Back)铜底盖(S/S case back)透视底盖(See-through case back)锁底盖(Screw back)O令(O-ring)(Gasket)生耳/钢闩（End-piece/pin）3>表壳打磨拉沙（Hair Brushed）12/6H方向直沙(912/6H vertical brushed)3/9H方向横沙(3/6H horizontal brushed)圆沙(Circle brushed)喷沙(Fine Sand Blasted)光令（Satin/Polish）壳:Case表胚：watch blank表圈：watch bezel表面：dial晌圈：springed metal ring内影：metal case decoratiue ring不锈钢实心表带：stainless steel semi-solid band包边带：side-wrapped band包边不锈钢表带：side-wrapped stainless steel band 织网表带：mesh band芯片：chip钨钢：tungsten steel皮表带：leather strap皮带扣：buckle forstap霸的：crown霸管：crown tube霸芯及驳管：stem and stem extension胶内影：housing/movement holder蓝宝石玻璃：sapphire crystal普通玻璃：ordinary glass凸晶玻璃：eye glass底盖：back cover生耳：spring bar生耳杆：T-bars with studs orscrews拆生钢枝：s/s pins and shafts拆生锣丝：removable screwed pin搓花钢枝：s/s knurled pins弹簧扣：spring buckel龟壳扣：clasps蝴蝶扣：folding clasps /butterfly style buckle 鸭嘴扣：duck-mouth buckle圆头饰钉：cabochon机芯：movement移印：padprinting吸塑包装：blister&packaging真空镀膜：vacuum coating蚀麦：etchedtrade mark單卜:dome len雙卜:curved len一、仕样不光边no polishing.['pɔliʃ]幼砂fine sand太阳砂radiation brushing.[reidi'eiʃən]打字stamped.[stæmp]光令mirror finishing光滑表面smooth surface光边polishing光边直砂6—12polished brushing光边圆砂circular polished brushing防水度water-resistant level直砂6-12 brushing砂纹sand brushing涂油add grease .[ɡri:s]镀黑black chrome plating .[krəʊm]填黑油black filled鱼鳞纹armor brushing.['ɑ:mə]圆砂circular brushing蚀字chemical etching .['etʃɪŋ]喷砂sand brushing横砂3-9brushing镭射字体laser二、表面（Dial）分位字尾minute struck日历窗date frame .[freim]字印marking字钉index.['indeks表面surface表面加工ackground finishing面底色background color面厚dial thickness面窗dial ring时位字尾hour struck牌子名brand name点dot镶唛applied logo钻石diamond钻石托diamond bushings三、表针（Hand）山型顶faceted分针minute hand平顶flat百分秒针chromo second hand .['krəuməu] 夜光luminous .['lu:minəs]表针hand秒针second hand针高hand height四、底盖（Caseback）刀口位opening slot内字印inside marking外字印outside marking波子底back snap底保护贴back protective sticker .['stikə] 底匙眼back key slot底盖caseback螺丝screw螺丝牙screw thread .[θred]米底point snap湾形底curved caseback .[kə:v]五、表带（caseband /wristket /band）中珠center link皮带strap/leather皮带扣利口tongue皮带环loop扣制buckle ['bʌkl]尾珠end piece拆生珠removable link/adjustable link表带caseband /wristket /band潜水扣dive buckle单接皮带扣deploy .[di'plɔi]边珠side link实心珠solid link珠宝扣jewellery buckle蝴蝶扣butterfly buckle双开蝴蝶扣hidden butterfly pushed button 头珠starting piece箭咀arrow .['ærəu]六、配件电池battery螺丝的头screw crown螺钉screw pin螺丝耳杆screw spring bar单胶圈的头single o-ring crown双胶圈的头double o-ring crown按的push button八角线octagon thread .['ɔktə,gɔn]八角形的octagon六角形的hexagon填夜光油luminous filled机芯movement实配机芯casing针pin软O-Ring soft o-ring硬o-ring rigid o-ring软胶I令soft plastic I-ring硬胶I令rigid I-ring白色I令white I-ring半透明I令semi-transparent I-ring发夹hair pin贴纸tape双面胶double side tape大头针friction pin字母通capsa pin-pipe（tube）压罩compression on holder[kəm'preʃən] 内罩movement holder螺丝巴管screw tubeT行巴管T-tube巴芯stem湾生耳banded spring bar生耳spring bar无托生耳free stand spring bar单托生耳single stand spring bar双托生耳dual stand spring bar ['dju:əl] 平头连斜巴flat head with chamfer平头巴的flat head圆头巴的round headT形巴的T-crown丝印玻璃silk screen glass镀膜玻璃plating glass单卜玻璃one side curved glass双卜玻璃both side curved glass蓝宝石水晶sapphire crystal .['sæf,aɪə]玻璃glass白板玻璃mineral glass水晶玻璃crystal glass七、组立（装配）不防水water proof failed不动formfit加防水油add silicon oil半跌half drop全跌full drop玻璃不配壳glass not fitting on case装配assembly配合fitting配带caseband fitting壳带配合不良poor fitting for case band 八、性能（function）拉力pull force顶力retention force.[ri'tenʃən]横拉力horizontal pull force .[,hɔri'zɔntəl] 防水测试不合格water test failed防潮water resist退return九、结构面平flat surface镶石圈stone top ringO-ring 坑o-ring ditch/ groove刀口位开在opening notch at .[nɔtʃ]刀口位opening slot大身3-9case side wall大身面3-9case surface细身面6-12case surface细身6-12case side wall开面opening开粗roughing内耳款inner lug width内映reflector买内影圈erflector ring丝吼inside diameter .[dai'æmitə]圈bezel弹珠结构ball structure止口高position for snap胶水glue展开长度open-up length压缩长度compressed length外耳款outer lug width避针为hand clearance夜光luminescent顶圈top ring壳耳case lug单卜upper curve bottom .[kə:v]石拓stone bushing巴孔crown opening圆壳round case方壳square case异形壳irregular case底平flat bottom企身为standing point字深=0.5depth of text=0.50有电池托w/battery strop没电池托w/o battery strop耳长lug diameter叉耳fork legs耳吼lug hole耳底lug case耳面lug surface耳脚lug stand耳款lug width检验尺寸inspection size加工尺寸production size按的位position for push button 玻璃位glass position石爪prong假螺钉decorating screw十、缺陷不足够insufficient [ɪnsə'fɪʃənt] 磨罍over polishing电镀不良poor plating车线不良poor stitching ['stitʃiŋ] 污物dirts利边sharp edge批锋burr.[bɜ:]甩字钉index fall out松loose花scratched表面脱色dial discolor欠缺missing出问题found problems打磨不良poor polishing砂孔sand hole砂过界over brushing打磨错误wrong polishing突出protruded.[prəʊ'tru:d]振刀纹rough turning mark氧化斑点oxidize spot.['ɔksɪ,daɪz] 破裂crack起泡bubble崩dented脱落come off倾斜poor printing损坏damaged紧tight轻微minor胶水过多excessive glue断裂broken蜡屎wax严重major变形deformed十一、其它反面图reversed view正常normal名称title制图drafter注意打磨caution on finishing待定T.B.A玻璃外围尺寸outer glass diameter要点remark规格format标准/正规standard检查/签名checker进出口import/export时装表fashion watch经典表classic watch运动表sports watch女/男装women/man model女/男装lady /gents model童装kids watch电子表digital watch日本/瑞士机芯Japan or Swiss movement 日本石英Japan quartz唛头logo/marking士啤spare parts大/小尺寸big/small size抛光polishing/shiny电镀plating防水water resistant功能function皮料/色卡material collection目录catalogue/catalog参考reference附上的附件attached/attachment图片/相片picture/photo方形/圆形square/round shaped椭圆oval .['əuvəl]有/无按的with/ without pusher产品/生产production/product彩图colourful drawing表面设计dial design确认/再次确认conform/double confirm 取消/保留cancel/keep订单order翻单repeat order新订单new order新款new model原始订单original order同样板一样same as sample样品sample出货样shipment sample确认样approval sample假版dummy sample .['dʌmi:]包装packing装箱单packing list发票invoice毛重/净重gross or net weight艺术字artwork单词/字母，信word /letter纸盒paper box小贴纸small sticker标签label吊牌hangtagPP胶袋polybag气泡袋bubble bag间电tow-tone透明的transparent多功能计时chrono。