汽车技术术语中英文对照翻译
汽车专业术语(中英对照)
汽车英文术语---中英对照1号厂房工艺布置方案图proposal of the Plant I layout 2 套two kitsJ型转弯试验test of J turn保险杠bumper变光开关simmer switch薄壳式结构shell construction操舵力试验steering effort test长途客车inter-city bus车辆转移台bus transfer衬垫pad除湿器moisture ejector搭接lap怠速时at idle底盘平移台chassis shuttle吊运装置overhead hoist镀锌板galvanized plate发车前准备pre-delivery发动机托架engine holding frame发动机中置式客车bus with under floor engine反冲试验kick-back test返工re-doing防滑地板no-skid floor防破坏vandal resistant风洞试验wind tunnel test改装厂refitting factory钢化玻璃toughened grass搁梁shelf beam更衣室restroom工位station功率突然变化影响试验test of effect of sudden power change 合笼mate恒温控制thermostatic control横风稳定性试验test of crosswind stability后围侧板rear wall side cover互换性interchangeability极限侧向加速度试验limiting lateral acceleration test阶路响应时间试验step response test结构完整性structure integrity静态操舵力试验static steering effort test举升hoist聚碳化透镜poly-carbonate len空气导流板air deflector宽敞悬臂式座椅roomy cantilevered seat亮丽的外表smart apperance磷化phosphating轮胎爆破响应时间试验test of burst response of tyre轮辋错动试验rim slip test轮椅升降机Wheel chair lift轮罩护板wheel house脉冲响应试验pulse response test内饰trim耐翻倾试验test of overturning immunity爬坡能力grade ability排水阀drain valve配电站power transformer substation拼装台collector频率响应时间试验frequency response test平衡水箱surge tank汽车平顺性单脉冲输入行驶试验automobile ride single pulse inp ut running test汽车平顺性随机输入行驶试验automobile ride random input runn ing test汽车悬挂系统固有频率与阻尼比的测定试验measurement of natu ral frequency and damping raito of suspension前围角板front wall angle cover嵌条insertion strip强制通风ram-air ventilation切割轮口wheel -arch cutting切齐trimming琴式驱动桥banjo type drive axle全天候空调系统full range A/C裙板skirt绕过障碍物试验obstacle avoidance test三类底盘three type chassis收油门后控制试验test of control at breakway 水洼ponding瞬态响应时间试验transient response test随车工具tool box梭梁stabilizing beam缩微图纸microfiche files停机时间downtime通风口duct图例legend无公害柴油clean diesel线束harness消音器muffler小批量产品be pilot斜撑bracing piece悬架举升试验jack-up test of suspension压条trim strip腰带式安全带diagonal safety belt腰梁waist rail仪表板dash board移线试验lane change test异形钢管special steel pipe翼板fender隐藏式固定concealed fastening遮阳板sun visor诊断报警系统diagnosis and alarming system织物纹里铝合金textured aluminum extrution制动稳定性试验test of braking stability中涂floating coat转向盘回正性试验test of steering wheel returnability转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test转向盘转角脉冲试验steering wheel impulse input test自动愈合的防腐材料self-healing corrosion preventative material 总装final assembly组合式客车车身modular bus body最小转弯直径试验minimum turning diameter test 左侧围应力蒙皮R/S stretching skin (road side)。
汽车常用术语中英文对照
汽车常用术语中英文对照气门 Valve顶置凸轮轴 Over Head Camshaft（OHC）顶置双凸轮轴 Double Over Head Camshaft（DOHC）或称Twin Camshaft直列四缸 Inline4水平对置发动机（Boxer Engine）四冲程汽油机（Reciprocating 4Stroke Cycle Engine）柴油机（Diesel Engine）转子发动机（Rotary Engine）气缸体（Cylinder Block）气缸套（Cylinder Liner）连杆（Connecting Rod）曲轴（Crank Shaft）油底壳（Oil Pan）活塞（Piston）活塞销（Piston Pin）活塞环（Piston Ring平衡机构（Balancer）气缸盖（Cylinder Head）进气门和排气门（Intake Valve/Exhaust Valve）气门座（Valve Seat）气门弹簧（Valve Spring）气门锁块（Cotter）气门间隙调节垫片（Shim）凸轮轴（Camshaft）摇臂（Rocker Arm）摇杆（Swing Arm）齿形皮带（Timing Belt）气门间隙调节器（又称液压挺杆）（Valve Lash Adjuster）配气相位（气门开闭角度）（Valve Timing）可变进气系统（Variable Induction System）化油器（Carburetor）喉管（Venturi）可变喉管（Variable Venturi）汽油泵（Fuel Pump）惯性增压（Inertia Change）进气管（Intake Manifold）节气门（Throttle Valve）空气滤清器（Air Cleaner）汽油喷射系统（Fuel Injection）空气流量计（Air Flow Meter）节气门体（Throttle Body）汽油喷嘴（Injector）单点喷射（Single Point Injection）自然进气（Natural Aspiration）涡轮增压器（Turbo Charger）中冷器（Inter Cooler）爆振（Knocking）爆振传感器（Knock Sensor）机械增压器（Super Charger）。
汽车英文术语的解释汇总
精心整理汽车专用术语大全? 变速器M（Manual）：手动变速器A（Automatic）：自动变速器N挡：空挡，车辆暂停使用，如等候红、绿灯。
D挡：行车挡。
2挡：中速挡，在雪地或市区等车速不高的情况下使用。
L挡：低速挡，用于爬斜坡或易打滑路面。
OD挡：超速挡，用于高速行驶情况钢圈与车胎(Wheel rim, Tire)轮胎面(Tire Tread)指轮胎面接触在地面的部份，为防止打滑及散热起见，在轮胎面设置有许多花纹。
无内胎轮胎(Tubeless Tires)R英寸接而成，目前的钢圈外环制造的很精确，以装配无内胎的轮胎。
铝合金钢圈(Alumminum-Rim)质轻，加工容易，是一体铸成，不易变形，外观多变化，目前多采用，有省油，导热性良好，强度分布均匀，减少滚动噪音的优点。
轮胎平衡(Wheel Balance)是前轮定位中，对轮胎的检查项目之一，轮胎若不平衡，会造成车辆行驶时，左右偏摆震荡上下跳动，方向盘摆震的现象，驾驶乘座极不舒适，必须配挂重铅块于钢圈的两侧，使之平衡。
车轮定位(Wheel Alignment)汽车的前轮，为顾及操作容易及行驶上的安全，减少轮胎的磨损，于设计时则?MPV趋向，Ｓ是小的意思。
Ｓ－车长一般在４．２—４．３ｍ之间，（当然，现在也有好多大型MPVSUV：SUV的全称是Sport Utility Vehicle，中文意思是运动型多用途汽车。
现在主要是指那些设计前卫、造型新颖的四轮驱动越野车。
SUV一般前悬架是轿车型的独立悬架，后悬架是非独立悬架，离地间隙较大，在一定程度上既有轿车的舒适性又有越野车的越野性能。
由于带有MUV式的座椅多组合功能，使车辆既可载人又可载货，适用范围广。
汽车专业词汇A-B（engine type) liquid cooled, in-line, 4cylinder, carb (发动机型号)水冷，直列，四缸，化油器式(engine) compression ratio (发动机)压缩比(engine) displacement (发动机)排量A/C blower 空调鼓风机A/C clutch 空调压缩机离合器A/C compressor MTG bracket 空调压缩机安装支架A/C control assy. 空调控制器A/C housing assy. 空调箱总成A/C low pressure switch 空调低压开关A/C mode select switch 空调状态选择开关abdomen performance criterion 腹部性能指标Abdominal Peak Force 腹部力峰值ABS 防抱死制动系统adjuster washer 调整棘片adjuster, diff. bearing 差速器轴承调整螺母Adjustment system 调节装置Administration and Registration Division 管理科Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts Which Can Be Fitted and/or Be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of These Prescriptions关于对轮式车辆、安装和/或用于轮式车辆的装备和部件采用统一条件并相互认可基于上述条件批准的协定书Air Pressure of Tire 轮胎气压Air type 空气型air valve 空气阀air-cooled 风冷Aisles 通道Alcohol 酒精all bearing 球轴承alternater bracket 发动机支架alternator 交流发电机alterntor assembly 交流发电机总成angles drift off vertical line 指针偏离垂直线的角度Angular diameter of the retro-reflecting device 回复反射装置的角直径annex 附件Announcement 公告anti, shutdown screw 防不灭车调整螺钉Antilock Brake System 防抱死制动系统appendix 附录Applicable motor vehicle 适用机动车Applicable scope 适用范围applicant 申请人attaching location of seat belt anchorage 座椅安全带固定装置的固定位置attachment 附属文件Attendants onboard 车上值班人员automatic chock cover setting 自动阻风门盖调到automotive electric system 汽车电系automotive engine system 引擎系统automatic transmission 自动变速器，自动排挡变速箱Auxiliary Brake 辅助制动器Auxiliary Direction Indicator Lamps 辅助转向信号灯auxiliary spring 副簧backup washer 支撑挡圈bail wire 卡紧环balance tube 平衡管ball 钢球ball bearing 球轴承ball joint assy. , upper 上球销总成ball valve 球阀ball valve, inlet 进油口球阀bar 拉杆barrier 障碍壁bellblead door 混合风门bleeder screw 放气螺钉blower assy. 鼓风机总成blower motor 鼓风发电机blower resistor 鼓风机电阻blower switch 鼓风机开关body 车身,阀体body & liftgate assembly 车身和举升门总成body assy. 车身总成body block 人体模块boltbootbrake alarm lamp switch 制动报警灯开关Brake booster 制动助力器brake caliper 制动钳brake caliper assy. 制动钳总成brake caliper piston 制动钳活塞brake combination valve 制动组合阀brake disc 制动盘Brake drum 制动鼓brake fluid 刹车油Brake hose 制动软管brake warning lamp 制动报警灯brake warning switch 制动报警开关Braking efficiency 制动效能braking force control system 制动控制装置Braking wheel 制动轮branch office 分署breaker 断电器bridge 过桥broadcasting vehicle 广播车brush 碳刷总成?cable-operated control system 液压式离合器系统Calibration factor of a data channel 数据通道校正系数calibration gas 标定气体calibration method 标定方法caliper assy. , front brake 前制动钳总成Camber 外倾camber angle 前轮外倾角camshaft 凸轮轴camshaft oil gallery 凸轮轴油道cap 加机油口盖carburetor overhaul scheme 化油器分解图carburetor working scheme 化油器工作示意图carcase 胎体case runout (Max.) 差速器壳圆跳动（最大）Caster 后倾Catalyst 催化器category 类别cement and aggregate 水泥和混凝料Centreplane of occupant 乘员中心面Certified 经认证的check bracket 限位器支架check nut 限位器螺母check valve 单向阀check valve hole 回止阀孔check valve retainer 单向阀保持架check valve spring 单向阀弹簧check weight 回止块Chigi Circular No. 地技第…号Chigi No. 地技第…号Child Restraints 儿童约束装置clamp 卡圈Clamp ring type 锁紧圈式Cleaning efficiency 清洗效率Cleaning period 清洗周期clearance 最小离地间隙Clearance Lamp 示廓灯clinder head 气缸盖clip 卡子cluster housing 组合仪表壳Clutch system 离合器collapsible spacer 可压缩隔垫collector 拼装台colorimeter 色度计coloured-light unit 有色灯光组column assy. 转向管柱总成combination brake switch and proporting 组合阀combined lamp 复合灯combined pump 复合泵combined pump diaphragm 复合泵膜片combined pump diaphragm rod 复合泵膜片杆condenser assy. 冷凝器总成conduit pipe 导管cone , diff. side bearing 差速器轴承，内圈带滚子cone, pinion front bearing 主动齿轮前轴承内圈带滚子cone, pinion rear bearing 主动齿轮后轴承内圈带滚子Confirmor 确认者connecting rod 连接杆connecting link 连接杆connecting rod journal diameter 连杆轴径connecting rod journal width 连杆轴径宽度Cornering Lamp 转弯灯corrected 修正的cotter 开口销counter 5th gear 中间轴五档齿轮counter shaft 中间轴coupled condition 连接状态Coupling Device 牵引装置cover 端盖cover & plate assy. 离合器盖及压盘总成cover assy. , air cleaner 空气滤清器盖总成Crush rate 压碎速率Crush Strength 压碎强度Cumulative time 累计时间cup 皮碗cup, diff. side bearing 差速器轴承外圈cup, pinion front bearing 主动齿轮前轴承外圈cup, pinion rear bearing 主动齿轮后轴承外圈Cut-off 明暗截止线cycle 冲程cyclinder head cover 气门室罩Date of notification 认可日期Deceleration of the structure 地板减速度Definitions 定义Definitions 术语deflection 偏移defroster 除霜器dehydrator 储液器和干燥器delay valve 延迟阀Design torso angle 设计躯干角designated 认定diaphragm spring 膜片弹簧Diesel fuel 柴油Diesel oil 轻柴油diesel smoke 柴油排烟Diesel smoke measuring instrument 柴油机排烟测量仪diesel-powered motor vehicle 柴油机动车differential case 差速器壳differential gear 半轴齿轮differential gearbox , front axle 前桥减速器differential gearbox , rear axle 后桥减速器Director-General of Motor Vehicle Inspection and Registration Office 机动车检验注册署长disc brakes 碟式刹车disc brake 盘式制动器disk assy. , clutch drived 从动盘总成disk type braker 盘式制动器Displacement 排气量Displacement system 位移装置Distillation properties 分馏特性distillation temperature 馏出温度door hinge plate 车门铰链垫板doors assembly & body accessories 前后车门总成及其附件double-lip seal 双唇油封double-tire 双胎dowel pin 定位销dowel pins-pump ring 定子定位销DRAWING PROCEDURE 绘制规程drier 干燥剂drier receiver 贮液干燥器drier receiver body 贮液气壳体dry-bulb 干球dummy 假人dump 自卸车dust boot 防尘罩Dynamic test 动态试验汽车专业词汇E-F? ECE Regulation ECE法规eddy-current type 电涡流式efe heater 进气加热器Effective height 有效高度end clearance 轴向间隙ENFORCEMENT PROCEDURE 实施规程Enforcement Regulation 实施规则engine 发动机，引擎Engine and Power Train System 发动机及动力传动系engine assy. 发动机总成engine displacement 发动机排量engine hood 发动机罩engine intake manifold 发动机进气歧管engine load 发动机负荷Examination 审查examination affair 审查事务Exception to application 不适用条款excrement 排泄物exhaust 排水管exhaust duration 排气持续角exhaust emission 排气排放物Exhaust Emission Control Device 排放物控制装置exhaust hose 排放管exhaust manifold （发动机）排气歧管factory plate model 厂牌型号fan 风扇fan belt 风扇皮带fan & viscous drive 风扇及硅油离合器fast idle cam 快怠速凸轮fast idle cam link 快怠速凸轮连杆fast idle cam second step 快怠速凸轮第二阶段fast idle cam setting index 快怠速凸轮调整刻度fast idle mode 快怠速状态fast idle screw 快怠速调整螺钉filterFire truck 消防车fitting, flow control valve 流量控制阀接头fix shaft 定位轴flange 法兰flash point 闪点flasher, hazard lamp 危险报警闪光器Flexible Disk 软盘float 浮子float level 浮筒油面高度float pin 浮子轴foot angle quadrant 小腿夹角量角器fork 拨叉Formalin 福尔马林forward-opening inner door 内门前开型four-stroke cycle 四行程引擎four-wheel drive motor vehicle 四轮驱动的机动车Four-wheeled 四轮Frame 车架Frame and Body 车架及车身Friction clutch 摩擦离合器front brake disc assy. 前制动盘总成front case 前壳体front case of vacuum booster 助力器前壳体front coil spring 前螺旋弹簧front combined lamps 前组合灯front disk braker 前盘式制动器front edge 前边缘front end of shield 发电机前端盖front engine front drive F.F.式车辆front engine rear drive F.R.式车辆front stabilizer 前稳定杆front suspension 前悬吊front thrust plate 前配流盘front transfer 车辆转移台front tube failure 前管路失效状态front wall angle cover 前围角板front washer pump 前洗涤器泵front washer reservoir 前风挡洗涤器储液罐front wheel 前轮，前壳体front wheel alignment 前轮定位Fuelfuel pump 然油泵Fuel Resistance 耐油性fuel sensor 燃油（箱）传感器fuel sensor harness 燃油传感器线束fuel supply system 供油系Fuel System 燃料系Fuel System of Motor Vehicles Whose Fuel Is High-Pressure Gas 以高压气体作为燃料的机动车燃料系Fuel System of Motor Vehicles Whose Fuel Is Producer Gas 以发生炉煤气作为燃料的机动车燃料系fuse?gas sample 样气gas turbine 燃气轮机gasket 节温器密封垫，衬垫gasket cylinder head cover 气门室罩垫gasket, intake manifold 进气歧管衬垫gasket, liftgate handle 举升门手柄垫片Gasoline 汽油gasoline fueled motor vehicle 汽油机动车gathering heat cover-TCV system TCV 系统集热罩gear , counter shaft fifth 五档中间齿轮General Construction 通用结构GENERAL PROVISIONS 通用规则General provisions 一般规定generator 发电机Glazing 车窗glove box lamp 杂物箱灯Goods-Loading Accommodation 载货装置governor type 调节器式Gravimeter 重力计Gross Vehicle Weight 车辆总重harness 线束harness, body 车身线束harness, engine housing 发动机仓线束harness, lift gate 尾门线束hatch-back 掀背型Hazard Warning Lamps 危险报警闪光灯head 缸盖head form 头部模型head performance criterion 头部性能指标Head Restraint 头枕hereinafter referred to as 下文称为Hereinafter the same 下文同hi-beem indicator lamp 组合仪表远光指示灯high idle speed 高怠速high pressure gas 高压气体high range 高档High-floor 高地板High-floor that can be opened in three ways 三向开启的高地板High-Pressure Gas Transport Devices 高压气体运输装置hip angle quadrant 臀部角度量角器hoisthose, coolant recover 冷却液回收管hose, radiator inlet 散热器进水软管hose, radiator to water pump 散热器至水泵软管hose, thermostat to intake minifold 节温器至进气歧管软管hot air 热空气hot idle mode 热怠速状态hot idle screw 热怠速调整螺钉housing 壳体，外壳housing assy. 壳总成housing clutch 离合器壳Hydrogen flame ionization detector 氢火焰离子化分析仪汽车专业词汇I-J? I/S locking rod 内锁止拉杆I/S release rod 内开启拉杆Identification Code 标记idle fuel tube 怠速油管idle fuel way 怠速油道idle jet 怠速喷口idle mixture screw 怠速混合气调整螺钉idle tube 怠速油管Illumination angle 入射角Illumination intensity 光照强度Illumination of the retro-reflecting device 回复反射装置的照度illuminations actually measured 实测照度Illuminometer 照度计IMPACT REDUCTION OF INSIDE REARVIEW MIRRORS 缓冲式室内后视镜IMPACT REDUCTION TYPE OUTSIDE REARVIEW MIRRORS 缓冲式后视镜Impact test 冲击试验Impactor 碰撞块IMPORTED MOTOR VEHICLE 进口机动车injector 喷油器inlet 进油口inlet hole 进气孔inlet hose 进风口inlet opening 进油口inlet tube 进油管inlet valve 进油阀Inner Dimension 内部尺寸inner shaft 内半轴inner tube 内胎intake heater 进气加热器intake manifold 进气歧管intake silencer 进气消声器intake valve 进气门intake valve timing 进气门定时integral place 整数integral power steering 整体式动力转向器integral type 整体式inter shaft assy. 动力转向中间轴总成Intercooler 增压中冷器Japan Automobile Manufacturers Association 日本汽车制造商协会Japan Automobile Standards Internationalization Center 日本汽车标准国际化中心Japanese Automobile Type Approval Handbook 日本车辆型式认证手册Japanese Industrial Standards 日本工业标准Jiko No. 自公第…号通告JIS 日本工业标准Jisei No. 自整第…号Jisha Circular 自车第…号通告Jiyu No. 自运第…号journal cross assy. 十字万向节总成keyKoshin No. 交审第xx号lamp switch, 4WD 四轮驱动灯开关lamp type 灯式Lap belt anchorages 腰带固定装置Large-Sized Rear Reflex Reflectors 大型后回复反射器Large-sized special 大型专用latch assy. , front RH. Door 右前门锁总成latch assy. , rear RH. Door 右后门总成lateral level 横向水平仪leading shoe 领蹄Lenslicense lamp 牌照灯lift gate 举升门liftgate assy. 举升门总成liftgate latch assy. 举升门锁总成liftgate lock assy. 举升门锁芯总成light source module 光源模组Light Vehicles 轻型车辆Light-Exposure and Light-and-Water-Exposure Apparatus 光线暴露及光线与水暴露设备lighting device 照明装置loaded WT 最大总质量Loading Capacity 载重量Loading platform 货箱Loading platform offset 货箱偏移量Local Land Transport Office 地方陆运署Local Office 地方署Location of business place 业务场所地点lock CYL assy. , RH. door 右车门锁芯总成lock piece, reverse gear 换档器锁片locking & indexing plate 锁止刻度盘low range lock plate 抵挡锁止板low speed jet 低速喷口lower control arm 下控制臂总成lower pressure switch 低压开关lubricant capacity 润滑油加注油lubricants 润滑油Lubricating oil 润滑油lubricating system 润滑系luminance factor 亮度因数luminous flux 光通量?Main honeycomb block 主蜂窝块main injection jet 主喷口main jet 主量孔main oil gallery 主油道main spring 主簧Make and type 厂牌和型号Management supervisor 主管人manual transmission 手动变速器，手排挡变速箱Manufacturer 制造者MANUFACTURER TEST 制造者试验mateMax. torque 最大扭距Maximum Loading Capacity 最大载重量maximum out-of round(all journals) 最大不圆度（所有轴径）maximum output 最大功率Maximum Stable Inclination Angle 最大稳定倾斜角maximum taper(all journals) 最大锥度（所有轴径）Maximum Torque 最大扭矩Measuring equipment 度量装备Measuring tape 卷尺mechanical steering 机械转向器Mini-sized 微型mini-sized motor vehicle 小型机动车Minister of Land, Infrastructure and Transport 国土交通大臣Ministry of Land, Infrastructure and Transport 国土交通省Ministry of Transport 运输省。
汽车专业术语(中英对照版)
terms
1
密封件
sealing
1.1
前门和后门密封件
front door&rear door sealing
前门开关护罩
front door switch watershield
前门挡水膜片
front door waterdam
后门挡水膜片
rear door waterdam
前门密封条
front door weatherstrip
侧围内饰板接板固定器
quarter trim panel extension fastener
后柱内饰罩
rear pillar trim cover
举升门柱内饰罩
liftgate pillar trim cover
侧围内饰板通风网
quarter trim louver screen
轮罩内饰板
wheelhouse trim panel
后门腰线外密封条
rear door outer belt weatherstrip
前门玻璃滑道密封条
front door glass channel weatherstrip
后门玻璃滑道密封条
rear door glass channel weatherstrip
门到边梁密封条
door to rocker seal
4
遮阳板
sunvisor(visor)
遮阳板总成-无化妆镜
sunvisor assembly-w/o lighted
遮阳板总成-带化妆镜
sunvisor assembly-w/lighted
遮阳板
sunvisor
遮阳板本体保护条
汽车专业用语中英文翻译对照
2009-12-16 11:50发动机 engine内燃机 intenal combusiton engine动力机装置 power unit汽油机 gasoline engine汽油喷射式汽油机 gasoline-injection engine火花点火式发动机 spark ignition engine压燃式发动机 compression ignition engine往复式内燃机 reciprocating internal combustion engine 化油器式发动机 carburetor engine柴油机 diesel engine转子发动机 rotary engine旋轮线转子发动机 rotary trochoidal engine二冲程发动机 two-stroke engine四冲程发动机 four-stroke engine直接喷射式柴油机 direct injection engine间接喷射式柴油机 indirect injection engine增压式发动机 supercharged engine风冷式发动机 air-cooled engine油冷式发动机 oil-cooled engine水冷式发动机 water-cooled engine自然进气式发动机 naturally aspirated engine煤气机 gas engine液化石油气发动机 liquified petroleum gas engine柴油煤气机 diesel gas engine多种燃料发动机 multifuel engine石油发动机 hydrocarbon engine双燃料发动机 duel fuel engine热球式发动机 hot bulb engine多气缸发动机 multiple cylinder engine对置活塞发动机 opposed piston engine对置气缸式发动机 opposed-cylinder engine十字头型发动机 cross head engine直列式发动机 in-line engine星型发动机 radial engine筒状活塞发动机 trunk-piston engine斯特林发动机 stirling engine套阀式发动机 knight engine气孔扫气式发动机 port-scavenged engine倾斜式发动机 slant engine前置式发动机 front-engine后置式发动机 rear-engine中置式发动机 central engine左侧发动机 left-hand engine右侧发动机 right-hand engine短冲程发动机 oversquare engine长冲程发动机 undersquare engine等径程发动机 square engine顶置凸轮轴发动机 overhead camshaft engine双顶置凸轮轴发动机 dual overhead camshaft engine V形发动机 V-engine顶置气门发动机 valve in-head engine侧置气门发动机 side valve engine无气门发动机 valveless engine多气门发动机 multi-valve engine卧式发动机 horizontal engine斜置式发动机 inclined engine立式发动机 vertical engine二冲程循环 two-stroke cycle四冲程循环 four-stroke cycle狄塞尔循环 diesel cycle奥托循环 otto cycle混合循环 mixed cycle定容循环 constant volume cycle工作循环 working cycle等压循环 constant pressure cycle理想循环 ideal cycle热力循环 thermodynamic cycle冲程 stroke活塞行程piston stroke长行程 long stroke上行程 up stroke下行程 down stroke进气行程intake stroke充气行程charging stroke压缩行程compression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程 power stroke排气行程exhaust stroke膨胀换气行程 expansion-exchange stroke换气压缩行程 exchange-compression stroke止点dead center止点 dead center上止点 top dead center(upper dead center)下止点 lower dead center(bottom dead center)上止点前 budc(before upper dead center)上止点后 atdc(after top dead cetner)下止点前 bbdc(before bottom dead center)下止点后 abdc(after bottom dead center)缸径 cylinder bore缸径与行程 bore and stroke空气室energy chamber气缸余隙容积 cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积 maximum cylinder volume压缩室 compression chamber排气量displacement发动机排量 engine displacement活塞排量 piston swept volume气缸容量 cylinder capacity单室容量 single-chamber capacity容积法 volumetry压缩比compression ratio临界压缩比critical compression ratio膨胀比 expansion ratio面容比 surface to volume ratio行程缸径比 stroke-bore ratio混合比 mixture ratio压缩压力 compression pressure制动平均有效压力brake mean effective pressure(bmep) 空燃比 air fuel ratio燃空比 fuel air ratio燃料当量比 fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩 torque per liter升质量 mass per liter减额功率 derating power输出马力shaft horsepower马力小时，马力时 horsepower-hour总马力 gross horse power总功率 gross power净功率 net power燃油消耗量 fuel consumption比燃料消耗率 specific fuel consumption空气消耗率 air consumption汽车英文术语A ／C Air Conditioning 空调A ／T Automatic Transaxle (Transmission) 自动变速器ACC Air Condition Clutch 空调离合器ACT Air Charge Temperature 进气温度AFC Air Flow control 空气流量控制AFS Air Flow Sensor 空气流量传感器AI Air Injection 二次空气喷射ACL AirCleaner 空气滤清器AIV Air Injection Valve 空气喷射阀ALCl Assembly Line Communication Link 总装线测试插座ALDl Assembly lne Diagnostic Link 总装线诊断插座ALT Alternator 交流发电机APS Absolute Pressure Sensor 绝对压力传感器ATS Air Temperature Sensor 空气温度传感器AP Accelerator Pedal 加速踏板ABS Anti-lock Brake System 防抱死刹车系统ATF Automatic Transmission Fluid 自动变速箱油液A ／F Air Fuel Ratio 空气燃料混合比AMP Ampere(S) 安培( 电流强度) APPROX Approximately 大约，近似ATDC After Top Dead Center 上止点后AUTO Automatic 自动ATT Attachment 附件ALR Automatic Lock Return 自动馈回缩器B+ Battery Positive Voltage 蓄电池正极BARO Barometric Pressure 大气压力BARO Sensor Barometric Pressure Sensor 大气压力传感器BP Barometric Pressure Sensor 大气压力传感器BAT Battery 电瓶BTDC Before Top Dead Center 上死点前BDC Bottom Dead Center 下死点CMP Camshaft Position 凸轮轴位置CARB Carburetor 化油器CCC Converter Clutch Control 转换离合器控制CDI Capacitive Discharge Ignition 电容放电式点火CMFI Central Multiport Fuel lnjectoion 中央多点燃油喷射CES Clutch Engage Switch 离合器接合开关CFI Central Fuel lnjection 中央燃油喷射CFI Continous Fuel Injection 连续燃油喷射CID Cylinder Identification Sensor 汽缸传感器CIS Continous Fuel lnjection 连续燃油喷射CKP Crank shaft Position 曲轴位置CKP Sensor Crank shaft Position Sensor 曲轴位置传感器CL Closed Loop 闭环控制CP Crank shaft Position 曲轴位置CPP Clutch Pedal Position 离合器踏板位置CPS Camshaft Position Sensor 凸轮轴位置传感器CPS Crank shaft Position Sensor 曲轴位置传感器CTP Closed Throttle Position ，节气门关闭位置CTS Engine Coolant Temperature Sensor 发动机水温传感器CYP Cylinder Position 汽缸位置CAT Catalytic Converter 触酶转换器CO Carbon Monoxide 一氧化碳CYL Cylinder 汽缸CPC Clutch Pressure Control 离合器压力控制CARB Carburetor 汽化器，化油器CPU Central Processing Unit 中央处理器CHG Charge 充电D —Jetronic Multiport Fuel Injection D 型多点燃油喷射DLC Data Link Connector 数据传递插接器DFI Direct Fuel Injection 直接燃油喷射DI Direct lnjecton 直接喷射DI Distributor lgnition 分电器点火DID Direct lnjection —Diesel 柴油直接喷射DTM Diagnostic Test Mode 诊断测试模式DTC Diagnostic Trouble Code 诊断故障码DLI Distributorless Ignitioo 无分电器点火DS Detonation Sensor 爆震传感器DIFF Differential 差速器DOHC DoubleOverhe~IdCamshaft 顶置双凸轮轴DPI Dual Point lnjection 两点喷射DRL Daytime Running Light 白天行驶灯E2PROM Electrically Erasable Programmable Read Only Memory 可以擦写的只读存储器EATX Electronic Automatic Transmission ／Transaxle 电控自动变速器EC Engine Control 发动机控制ECA Electronic Control Assembly 电子控制总成ECM Engine Control Module 发动机控制模块ECT Engine Coolant Temperature 发动机冷却水温EDIS Electronic Distributorless lgnition System 电子无分电器点火系统EEC Electronic Engine Control 电子发动机控制EEPROM Electrially Erasable Programmable Read Only Memory 可电擦写的只读存储器EFI Electronic Fuel lnjection 电控燃油喷射EGOS Exhaust Gas Oxygen Sensor 氧传感器EGR Exhaust Gas Recirculation 废气再循环EGRV ExhaustGasRecirculationvalve 废气再循环阀EGS Exhaust Gas Sensor 氧传感器EPROM Erasable PrOgrammable Read Only Menory 可擦写的只读存储器ESA Electronic Spark Advance 点火提前ESAC Electronic Spark Advance Control 点火提前控制EST Electronic Spark Timing 点火正时EVAP Evaporative Emission 蒸发排放污染EX Exhaust 排气ELD Electrical Load Detector 电子负载检测器EPS Electrical Power Steering 电子动力转向FC Fan Control 风扇控制FP Fuel Pump 燃油泵FWD Front Wheel Drive 前轮驱动FR Front Right 右前FSR Fail SafeRelay 失效安全继电器FIA Fuel lnjection Air 燃油喷射进气GEN Generator 交流发电机GND Ground 搭铁GALGallon 加仑H ／B Hatchback 掀背式H02S Heated Oxygen Sensor 加热型氧气传感器HC Hydrocarbons 碳氢化合物lA Intake Air 进气IAT Intake Air Temperature 进气温度IATS Intake Air Temperature Sensor 进气温度传感器lAC Idle Air Control 怠速控制IACV Idle Air control Valve 怠速空气控制阀ICM Ignition Control Module 点火控制模块ISC Idle Speed Control 怠速控制lAB Intake Air Bypass 进气歧管IAR Intake Air Resonator 进气共鸣器IMA IdleMixtureAdjustment 怠速混合比调整IMPS Intake Manifold Pressure Sensor 进气歧管压力传感器IN Intake 进气IG or IGN Ignition 点火燃烧ID Identification 辨证，识别ID or I ．D ．Inside Diameter 内径KAM Keep Alive Memory 磨损修正系数存储器K —Jetronic Continous Fuel lnjection 机械式连续喷射KE — Jetromc Continous Fuel lnjection 机电结合式连续喷射KS Knock Sensor 爆震传感器KOEO KEY —ONEngine —OFF 点火开关ON 发动机不启动KOER KEY —ONEngine —Running 点火开关ON 发动机运转L —Jetronic MultiportFuellnjeetion L 型多点燃油喷射LH —Jetronic MultiportFuel lnjection LH 型多点燃油喷射LHD Left Handle Drive 左侧驾驶L ／C Lock — up Clutch 锁定离合器LF Left Front 左前LSD Limited Slip Differential 防滑差速器LR Left Rear 左后L 一 4 In —Line Four Cylinder(engine) 直列式4 汽缸( 发动机) LED Light Emitting Diode 发光二极管M ／C Mixturure Control 混合气控制MAF Mass Air Flow 质量空气流量MAP Manifold Absolute Pressure 歧管绝对压力MAT Manifold AirTemperature 歧管空气温度MCS Mixture Control Solenoid 混合气控制电磁线圈MCU Microprocessor Control Unit 微处理器控制单元MFI Muhipoint Fuel lnjection 多点燃油喷射MFE MultipointFuel lnjection 多点燃油喷射Mil Malfunction lndicator Lamp 故障指示灯M ／S Manual Steering 手( 机械式) 转向MAF Mass Air Flow Sensor 空气流量计M ／T Manual Transmission 手动变速箱MCK Motor Check 马达检示MAX Maximum 极大值MIN Minimum 极小值MPI Multi Point lnjection 多点喷射NPS Neutral Position Switch 空挡开关N Neutral 空转位置( 空挡) NOX Nitrogen Oxides of 氮氧化合物02S Oxygen Sensor 含氧传感器P ／N Park ／Neutral Position 停车／空挡位置P ／S Power Steering Pressure Switch 动力转向压力开关PCM Power train Control Module 动力控制模块PCV Positive Crankcase Ventilation 曲轴箱强制通风PFI Port Fuel lnjection 进气门口燃油喷射PIP Position lndicator Pulse 曲轴位置传感器PNP Park ／Neutral Position 停车／空挡位置PROM Programmable Read Only Memory 可编程只读存储器PSP Power Steering Pressure 动力转向压力PSPS Power Steering Pressure Switch 动力转向油压开关p Park 停车PSAI Pulsed Secondary Air lnjection 脉动式二次空气喷射PGM —FI Programmed — fuel lnjection 程式控制燃料喷射PGM — IG Programmed lgnition 程式化点火PMR Pump Motor Relay 由泵马达继电器PSW Pressure Switch 压力开关PSF Power Steering Fluid 动力转向油Qty Quantity 数量RAM Random Access Memory 随机存储器RM Relay Module 继电器模块ROM Read Only Memory 只读存储器RR Rear Right 右后RHD Right Handle Drive 右侧驾驶REF Reference 参考RL Rear Left 左后SBEC Single Board Engine Control 单板发动机控制SEFI Sequential Electronic Fuel lnjection 次序电控燃油喷射SFI Sequential Fuel lnjection 次序燃油喷射' SMEC Single Module Engine Control 单片发动机控制SPI Single Point lnjection 单点喷射SAE Society of Automotive Engineers 美国汽车工程师学会SOHC Single Overhead Camshaft 顶置单凸轮轴SOI Solenoid 线圈SPEC Specification 规格S ／R Sun Roof 遮阳板SRS Supplemental Restrgint System 安全气囊STD Standard 标准SW Switch 切换开关SCS Service Check Signal 维修检示信号SEC Second 秒、第二TB Throttle Body 节流阀体TBI Throttle Body Fuel lnjectlon 节流阀体燃油喷射TC Turbocharger 涡轮增压器TCM Transmission Control Module 变速器控制模块TP ThrottlePosition 节气门位置TPS Throttle Position Sensor 节气门位置传感器TPS Throttle Position Switch 节气门位置开关TPI Tuned Port lnjection 进气口喷射TWC Three Way Catalytic Converter 三元催化反应器T Torque 扭力TDC Top Dead Center 上死点TDCL Test Diagnostic Communication Link 自诊接头T ／N Tool Number 工具编号TCC Torque Convertor Clutch 变扭器离合器TRC Traction Control 牵引控制VAF Volume Air Flow 体积空气流量VAT Vane AirTemperature 进气温度VCC Viscous Converter Clutch 变扭离合器VSS Vehicle Speed Sensor 车速传感器VSV Vacuum Solenoid Valve 真空电磁阀VTEC Variable Valve Timing Valve Lift 可变式气门正时VC Viscous Coupling 粘性偶和VIN Vehicle ldentification Number 车身号码( 出厂号码) VVIS Variable Volume Intake System 可变进气系统全部词汇下载汽车术语中英文对照（引擎系统）1、引擎系统(Automotive Engine System)燃烧室(Combustion Chamber) 活塞到达上死点后其顶部与汽缸盖之间的空间，燃料即在此室燃烧。
汽车英语-中英文对照
汽车英语，中英文对照表2[转]2007-04-15 20：02引擎机动力改装部分：进气管==Intake空气过滤器==冬菇头==air filter排气管==尾喉/死气喉==Exhause消音器==mufeler机油冷却器==oil cooler火花塞==火嘴==spark plug火嘴线==spark plug wires阀门==滑老==valve滑轮==pully活塞==piston曲轴==crankshaft凸轮轴==cam shaft气门弹簧==滑老弹弓==valve spring涡轮增压==turbo charger机械增压==super charger中冷==inter cooler放气阀门==放气滑老==blow—off valve废气阀门==wastgate压力控制器（怎么也想不出个的翻译）==水喉制==boost controller喷油嘴==大唧咀==Injector头批==down pipe行车电脑==ECU制动悬挂部分:轮圈==车伶==Rim刹车碟==迫力碟==rotor活塞卡钳==鲍鱼==caliper刹车片==迫力皮/来令片==brake pad避震==suspention(避震分为弹簧/弹弓==spring 和减震桶==shock 两部分）整套避震又叫 coilover波子塔顶==Pillow Ball Top Mounts防倾杆==sway bar用在车里的加强杆==tower bar用在车底的加强杆==lower arm bar传动部分:末齿比==大尾牙==Final Drive差速器==LSD离合器==极力子==clutch飞轮==flywheel车身部分:大包围==bodykit（车头==front bumper，车尾==rear bumper, 车别裙==side skirt) 尾翼==sopiler车头盖==hood （两种不同材质：碳纤维==carbon fiber, 玻璃钢==firberglass）Aerodynamic Drag 气动阻力装置基本装置，用来衡量汽车在行驶过程中的阻力系数; 风阻系数低意味着汽车的油耗和噪音降低;[AWD] All—Wheel Drive [详见：详解四驱系统］系统同时向四轮同时分配力量,不用手动选择两轮或四轮驱动［ABS］— Anti—lock Brake System 制动防抱系统［详见: 防滑控制系统]这是一项在80年代末才兴起应用的新技术，但发展得很快，现在已经成为许多轿车的必装件了。
汽车专业术语(中英文对照)
PP Product ion Proveout 生产验证TT O Tool Try-Out 工装设备试运行(J1) Job 1 整车投产DFME A Design Failure Mode Effe cts Analysis 故障模式影响分析设计DVP Design Verificat ion Plan 设计验证计划DVP&R Design Verificat ion Plan & Report 设计验证计划和结果F ME A Failure Mode Effe cts Analysis 故障模式影响分析FP DS Ford Product Development System 福特产品开发系统GYR Green-Yellow-Red 绿-黄-红MRD Materia l Required Date 物料要求到厂日O TT OK-TO-TOOL 可以开模TKO Tooling-Kick-Off 工装启动OEM original Equipment Manufacturer 设备最初制造厂FtF/F2F Face To Face 面对面会议PV Production Validation 产品验证OTS Off-Tooling-Sample 完全工装样件QOS Quality Operating System 质量运作体系TS-16949 Technical Specificat ion– 16949 技术规范-16949APQP Advanced Product Quality Planning 先期产品质量计划IPD In Plant Date 进厂日PPM Parts per Million (applied to defective Supplier parts) 零件的百万分比率（适用于供应商不合格零件）PPAP Production Part Approval Process 生产件批准程序Pre-PV Pre -Product ion Validat ion产品预先验证1PP- First Phase of Product ion Prove-Out 第一次试生产3C Customer(顾客导向)、Competit ion(竞争导向)、Competence（专长导向）4S Sale, Sparepart零配件, Service, Survey信息反馈5S 整理，整顿，清理，清洁，素养8D- 8 DisciplineABS Anti-lock Braking SystemAIAG 美国汽车联合会ANPQP Alliance New Product Quality ProcedureApport ion ment 分配APQP Advanced Product Quality PlanBacklite Wind shield 后窗玻璃Benchmark Data 样件资料bloodshot adj.充血的, 有血丝的BMW Bavarian Motor WorksC.P.M Certified Purchasing manger 认证采购经理人制度CB- Confirmat ion Build 确认样车制造CC- Change CutOff 设计变更冻结CC\SC- critical/significant characteristicCC R Concern & Countermeasure Re questCC T Cross Company TeamCharacteristics Matrix特性矩阵图COD Cash on Delivery 货到付现预付货款(T/T in advance) C P1- Confirmat ion Prototype 1st 第一次确认样车CP2- Confirmat ion Prototype 2nd 第二次确认样车Cpk 过程能力指数Cpk=Zmin/3CPO Complementary Parts orderCraftsmanship 精致工艺Cross-funct ion al teams 跨功能小组CUV Car-Based Ultility VehicleD1：信息收集；8DD2：建立8D小组；D3：制定临时的围堵行动措施，避免不良品流出；D4：定义和证实根本原因，避免再发；D5：根据基本原因制定永久措施；D6：执行和确认永久措施；D7：预防再发，实施永久措施；D8：认可团队和个人的贡献。
最全汽车行业术语英文翻译
最全汽车行业术语英文翻译1. 汽车类型- Sedan: 轿车- Hatchback: 掀背车- SUV (Sport Utility Vehicle): 运动型多功能车- MPV (Multi-Purpose Vehicle): 多功能车- Coupe: 轿跑车- Convertible: 敞篷车- Pickup: 皮卡车- Van: 面包车- Electric Vehicle (EV): 电动汽车- Hybrid Vehicle: 混合动力汽车2. 发动机和动力系统- Engine: 发动机- Horsepower (HP): 马力- Torque: 扭矩- Fuel Injection: 燃油喷射- Turbocharger: 涡轮增压器- Supercharger: 机械增压器- Cylinder: 气缸- Transmission: 变速器- Manual Transmission: 手动变速器- Automatic Transmission: 自动变速器- Continuously Variable Transmission (CVT): 连续变速器- Four-Wheel Drive (4WD): 四轮驱动- All-Wheel Drive (AWD): 全轮驱动- Electric Motor: 电动机- Battery Pack: 电池组3. 车身部件- Chassis: 底盘- Bodywork: 车身- Hood: 发动机盖- Trunk: 后备箱- Bumper: 保险杠- Fender: 车翼- Door: 车门- Windshield: 前挡风玻璃- Roof: 车顶- Spoiler: 尾翼- Headlights: 前灯- Taillights: 尾灯4. 汽车零部件- Brakes: 制动器- Suspension: 悬挂系统- Steering Wheel: 方向盘- Tires: 轮胎- Exhaust System: 排气系统- Air Conditioning: 空调系统- Radiator: 散热器- Battery: 电池- Alternator: 发电机- Starter Motor: 起动机- Fuel Pump: 燃油泵- Ignition System: 点火系统5. 汽车性能指标- Acceleration: 加速度- Top Speed: 极速- 0-60 mph Time: 0-96公里/小时加速时间- Fuel Efficiency: 燃油效率- Range: 续航里程- Curb Weight: 空载重量- Gross Vehicle Weight (GVW): 总重量- Wheelbase: 轴距6. 安全设备- Seatbelt: 安全带- Airbags: 气囊- Anti-lock Braking System (ABS): 防抱死制动系统- Electronic Stability Control (ESC): 电子稳定控制系统- Tire Pressure Monitoring System (TPMS): 轮胎气压监测系统- Adaptive Cruise Control: 自适应巡航控制- Blind Spot Detection: 盲点监测以上是最全汽车行业术语的英文翻译，希望能对您有所帮助！。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Back warning sensor
门框
Door frame
电动座椅调节装置
Seat height adjuster
油箱盖
Fuel filler lid
可锁闭功能杂物箱
Glove box locking system
方向盘音响调节装置
Steering wheel remote control
A pillar
后轮碟刹
Rear Disc brake
中控台
Mirror base
气囊(驾驶座+副驾驶座)
Air bag (driver seat + co-driver seat)
侧挡板
Fender panel
侧气囊/气帘
Side air-bag or curtain air bag
转向轮转向角，车轮转角
音响喇叭
Audio speaker
车窗（侧面）
Side window
驾驶座/副驾驶座
driver seat/co-driver seat
车门把手
Door handles
车内门柄
Switches of door trim
侧装饰条/腰线
Side-garnish / Character line
后排座椅
2ndrow seat
后备箱盖
Trunk lid
仪表板
Supervision cluster
后反光灯设计
Design of the rear reflecter
手刹
Parking brake
汽车牌照
Number plate
天窗
sunroof
汽车品牌标识
LOGO
上下坡辅助系统
Hill ascent/Hill Descent Control (HAC,HDC)
汽车翻译常用术语表
常用词
两厢车
hatchbackXXX幅来自XXX hood三厢车
sedan
动感/运动的
dynamic/sporty
大气/小气
grand/petty
中庸
mediocre
张扬
showy
前卫
avant-garde
稳重，厚重，沉稳
staid,thick, stable
家用/商用
family/business use
变速换档杆
Gear shift
引擎盖流线设计
Hood Character line
仪表中央盒
Center fascia
前挡风玻璃
Front windshield glass
中央手枕箱
Consol box
后视镜
Rear view mirror
前排通风器
Air vent(front)
顶棚(车顶)
Roof
引擎盖到后保险杆的顶弧线
Overall roof line from bonnet to rear bumper
头上空间
Overhead Space
车身线（上部）
Characterline(upper)
茶杯架设计
Cup holders
车身线（底部）
Characterline(bottom)
杂物箱（副驾驶前）
Wheel angle
前雾灯
Front fog lamp
挡泥板
Mud/guardWheel apron
智能钥匙
Keyless entry (Remote Key)
(车身)轮罩[拱]
Wheel arch
电动车窗
Power window
车桥,轮轴
Wheel axle
电动门锁
Power door lock
差速锁
EDS
悬挂
suspension
后面
Rear view
电控可折叠外后视镜
Electric Folding Outside Mirror
尾灯
Rear lamp/taillight
汽车脚垫
Car Mat
组合灯
Combination lamp
木纹内饰
Wood grain
后挡风玻璃
Rear windshield
排量
Displacement
大众化
popular
6碟CD
6-CD changer
全时四驱
AWD (Full-Time 4WD）
外观
Exterior
正面
Front view
内饰
Interior
前大灯
Headlights/head lamp
前排座椅
1strow seat
前格栅
Radiator grille
扶手
Arm rest
前保险杆
Front bumper
组合仪表板
Instrument cluster
前雾灯
Front fog lamp
方向盘
Steering wheel
进风口
Air-intake
方向盘遥控
Steering wheel remote controls
前引擎盖
Hood
仪表盘
Dashboard
引擎盖外观
Appearance of hood area
轴距
Wheel base
电动后视镜
Power Mirror
气坝/前扰流
Air dam
真皮座椅
Leather seat
合金车轮
Alloy wheel
真皮方向盘+排挡头
Leather steering wheel & TGS knob
腰线/防滑条
Waist line mold'g or side protector
车内照明灯+上方储物盒
Room lamp + overhead consol
雨刮/自动感应雨刮
Wiper/auto windshield wiper
车门装饰条
Door trim
后门装饰条
Rear door trim
侧面
Side view
门边地图架
Map pocket
后三角窗
Rear quarter glass
后车窗
Rear window
金属内饰
Metal grain
后装饰条
Rear-garnish
17’’轮胎
17’’Tyre
排气管的设计
Muffler/Exhaustpipe
车载(蓝牙)免提电话
Bluetooth hands-free
后保险杆的设计
Rear bumper
MP3音频播放器(i-pod)
MP3 audio (i-pod)
Glove box
车顶线
Roofline
手刹
Parking brake
挡风玻璃
Windshield(Greenhouse)
转向指示灯
Turn signal lamp
配置
Specifications
玻璃窗
Quarter glass
空调
Air conditioner
车轮
Wheel
ABS防抱死系统
ABS
A柱