通过VCDs 11.11软件对大众7速和6速DSG进行重置

Contents
[hide]
1 Basic Setting 2 Special Procedures

2.1 Defined Test Drive

2.1.1 Special Notຫໍສະໝຸດ sBasic Setting
Prerequisites:
No Fault Codes stored in the TCM Temperature 30° C - 60° C. The Measuring Block value for G510 is found in group 011.1 Selector Lever in P Ignition ON, Engine OFF Parking brake applied Brake Pedal operated (hold for the whole procedure) Throttle Pedal not operated
[Done, Go Back] Switch off Ignition, wait for a few seconds and switch it back on. [Fault Codes - 02] Check and clear any fault codes. [Close Controller, Go Back - 06] Perform the Defined Test Drive below.
A = Gears 4th or 6th (4th is preferred) B = Gears 3rd, 5th or 7th (5th is preferred)
Using the Tiptronic shifters maintain the range of 2,000 -to- 4,500 RPM and drive in each gear group (A and B) for no less than one full minute (two minutes are preferred). Use variable accelerator pedal positions but accelerate to full throttle at one point in each gear group during this one minute process.
DSG Resetting guide through VCDs 5053 for VW 7-Speed and 6-Speed
[Go!] [ON/OFF/Next] may be necessary
The live data should display 4 | 0 | 0 in Basic Settings. This may take up to 2 -to- 5 minutes. After the 4 | 0 | 0 results are displayed, start the engine immediately and allow it to idle. If 4 | 0 | 0 is not shown do NOT start the engine, something is wrong with the procedure or the transmission.
The live data should display 254 | 0 | 0 to confirm a successful Basic Settings after 3 -to- 6 minutes.

254 | 7 | 0 alone would Not be complete yet and 255 | 0 | 0 would indicate the basic settings was interrupted or failed.
Special Procedures
Prerequisites:
Transmission fluid greater than 30* C. The Measuring Block value for G510 is found in group 011.1 Do Not use Cruise Control.
Special Notes
Some modules do not require the use if the [ON/OFF/Next] button. If an Error is displayed after clicking the button, or the Basic Settings status does not switch to On, let the selected group and procedure finish on its own.
Defined Test Drive
Suggested test drive after replacing the Mechatronics module/TCM or successful basic setting.
With the shifter in Drive accelerate at half throttle to 2nd gear. Stop and repeat half throttle acceleration into 2nd gear. Stop followed by shifting into reverse and backing up two times. Stop followed by driving in each forward gear using the Tiptronic shifters for no less than 3 seconds per gear.
It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort the Basic Settings sequence prematurely if you hear clacking noises.
2/7
DSG Resetting guide through VCDs 5053 for VW 7-Speed and 6-Speed
The next portion of the drive must be done in any group choice of the following gears to maintain the proper RPM and maintain a safe driving distance on the road:
3/7
DSG Resetting guide through VCDs 5053 for VW 7-Speed and 6-Speed
6-Speed Direct Shift Gearbox (DSG/02E)
Ross-Tech Wiki Link: /wiki/index.php/6-Speed_Direct_Shift_Gearbox_(DSG/02E) General Information about this Transmission can be found in the Wikipedia entry. Additional information can be found in the Official Factory Repair Information and sources such as Bentley Publisher's SSP (Self-Study Program) .
MVBs 180.1 -and- 200.1 should confirm clutch adaptations with values of 3 or greater. If any portion of the adaptation is not completed it should finish on its own with normal driving.
DSG Resetting guide through VCDs 5053 for VW 7-Speed and 6-Speed
7-Speed Direct Shift Gearbox (DSG/0AM)
Ross-Tech Wiki Link: /wiki/index.php/7-Speed_Direct_Shift_Gearbox_(DSG/0AM) General Information about this Transmission can be found in the Wikipedia entry. Additional information can be found in the Official Factory Repair Information.
NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test drive. [Select] [02 - Transmission] [Basic Settings - 04] Group 060 1/7
NOTE: If the test drive cannot be performed in the recommended way or the necessary time, any remaining adaptations will be performed automatically during normal driving.
Contents
[hide]
1 Basic Setting

1.1 Transmission Tolerances (Engaged Calibration) 1.2 Transmission Tolerances (Synch. Point. Measurement) 1.3 Clutch Adaptation 1.4 Reset Values (Clutch Safety Function) 1.5 Reset Values (Pressure Adaptation) 1.6 Reset Values (Steering Wheel Paddle Installation) 1.7 Reset Values (ESP & Tip Cruise Control Installation)