PS7200R中文资料

FEATURES•LOW C X R:C X R = 11 pF • Ω•LOW OUTPUT CAPACITANCE:C OUT = 1.1 pF TYP • 1 CHANNEL TYPE:(1a output)•DESIGNED FOR AC/DC SWITCHING LINE CHANGER •SMALL AND THIN PACKAGE:4 pin SOP, Height = 2.1 mm •HIGH ISOLATION VOLTAGE:BV = 1500 Vr.m.s.•LOW OFFSET VOLTAGE•AVAILABLE ON TAPE AND REEL:PS7200R-1A-E3, E4, F3, F4DESCRIPTIONNEC's PS7200R-1A is a low output capacitance solid state relay containing a GaAs LED on the light emitting side (input side) and MOS FETs on the output side.It is suitable for high-frequency signal control, due to its low C x R, low output capacitance, and low off-state leakage current.APPLICATIONS•MEASUREMENT EQUIPMENTPART NUMBERPS7200R-1ASYMBOLSPARAMETERSUNITS MINTYP MAX V F Forward Voltage, I F = 10 mA V 1.21.4I R Reverse Current, V R = 5 VµA 5.0I LOFF Off-State Leakage Current, V D = 40 V nA 10C OUT Output Capacitance, V = 0 V, f = 1 MHz pF 1.1IFon LED On-state Current, I L = 120 mAmA 2.0R ON 1On-State Resistance, I F = 10 mA, I L = 10 mAΩ1012.5R ON 2 I F = 10 mA, I L = 120 mA, t ≤ 10 ms Ω1114t ON Turn-on Time, I F = 10 mA, V O = 5 V, R L = 500 Ω, PW ≥ 10 ms ms 0.030.5t OFF Turn-off Time, I F = 10 mA, V O = 5 V, R L = 500 Ω, PW ≥ 10 ms ms 0.3 1.0R I-O Isolation Resistance, V I-O = 1.0 kV DC Ω109C I-OIsolation Capacitance, V = 0 V, f = 1 MHzpF0.3D i o d e C o u p l e dELECTRICAL CHARACTERISTICS (T A = 25 °C)M O S F E TPS7200R-1A12Notes:1. Test Circuit for Switching Time:2. The turn-on time and turn-off time are specified as input-pulse width ≥ 10 ms. Be aware that when the device operates with an input-pulse width of under 10 ms, the turn-on time and turn-off time will increase.Pulse InputV O MonitorV LCalifornia Eastern Laboratories元器件交易网SYMBOLS PARAMETERS UNITS RATINGSDiode I F Forward Current (DC)mA 50VR Reverse Voltage V 5.0P D Power Dissipation mW 50I FPPeak Foward Current 2A 1MOS FETV L Break Down VoltageV 40I L Continuous Load Current mA 120I LP Pulse Load Current 3mA 240(AC/DC Connection)P D Power Dissipation mW 200Coupled BV Isolation Voltage 4Vr.m.s.1500P T Total Power DissipationmW 250T A Operating Ambient Temp.°C -40 to +85T STGStorage Temperature°C-40 to +100ABSOLUTE MAXIMUM RATINGS 1 (T A = 25°C)Notes:1.Operation in excess of any one of these parameters may result in permanent damage.2.PW = 100 µs, Duty Cycle = 1 %.3.PW = 100 ms, 1 shot.4. AC voltage for 1 minute at T A = 25 °C, RH = 60 % betweeninput and output.PS7200R-1ASYMBOLS PARAMETERSUNITSMIN TYP MAX I F LED Operating Current mA 21020V F LED Off VoltageV00.5RECOMMENDEDOPERATING CONDITIONS (T A = 25°C)PART NUMBERPS7200R-1A OUTLINE DIMENSIONS (Units in mm)12TOP VIEW1.LED Anode2.LED Cathode3.MOSFET4.MOSFET100806040200-25025507510085150100500-25025507585100TYPICAL PERFORMANCE CURVES(T A = 25ûC)MAXIMUM FORWARD CURRENTvs. AMBIENT TEMPERATUREMAXIMUM LOAD CURRENT vs. AMBIENT TEMPERATUREAmbient Temperature (T A ûC)M a x i m u m F o r w a r d C u r r e n t , I F (m A )Ambient Temperature (T A ûC)M a x i m u m L o a d C u r r e n t , I L (m A )元器件交易网P S 720R California Eastern Laboratories-1A TYPICAL PERFORMANCE CURVES (T A = 25ûC)FORWARD VOLTAGEvs. AMBIENT TEMPERATUREOUTPUT CAPACITANCE vs. APPLIED VOLTAGEAmbient Temperature (T A ûC)Applied Voltage, V D (V)F o r w a r d V o l t a g e , V F (V )O u t p u t C a p a c i t a n c e , C O U T (p F )1.61.41.21.00.8-25255075100f = 1 MHz5.04.03.02.01.00010203040506010-710-810-910-1010-1110-1210-1320406080100V D = 40 V3.0Normalized to 1.0 at T A = 25ûC,I F = 10 mA I L = 10 mA2.52.01.51.00.50.0-252550751006050403020109.29.49.69.810.0OFF-STATE LEAKAGE CURRENT vs. AMBIENT TEMPERATURELOAD CURRENT vs. LOAD VOLTAGEAmbient Temperature,T A (ûC)O f f -s t a t e L e a k a g e C u r r e n t , I L o f f (A )On-state Resistance, R on (Ω)N u m b e r (p c s )NORMALIZED ON-STATE RESISTANCEvs. AMBIENT TEMPERATUREN o r m a l i z e d O n -s t a t e R e s i s t a n c e , R o nAmbient Temperature,T A (ûC)ON-STATE RESISTANCE DISTRIBUTIONLoad Voltage, V L (V)L o a d C u r r e n t , I L (m A )元器件交易网TURN-OFF TIME vs. FORWARD CURRENTT u r n -o f f T i m e t o f f (m S )Turn-off Time t off (ms)0510********0.100.080.060.040.02V O = 5 V R L = 500 ΩForward Current I F (mA)T u r n -o n T i m e t o n (m S )TURN-ON TIME vs. FORWARD CURRENTForward Current I F (mA)60504030201000.010.020.030.040.05605040302010Turn-on Time t on (ms)N u m b e r (p c s )N u m b e r (p c s )NORMALIZED TURN-OFF TIME vs. AMBIENT TEMPERATUREAmbient Temperature,T A (ûC)N o r m a l i z e d T u r n -o f f T i m e , t o f fNormalized to 1.0at T A = 25ûC,I F = 10 mA V O = 5 V R L = 500 Ω3.02.02.51.51.00.50.0-25255075100Normalized to 1.0at T A = 25ûC,I F = 10 mA V O = 5 V R L = 500 Ω3.02.02.51.51.00.50.0-25255075100NORMALIZED TURN-ON TIME vs. AMBIENT TEMPERATUREAmbient Temperature,T A (ûC)N o r m a l i z e d T u r n -o n T i m e , t o nV O = 5 V,RL = 500 Ω2.01.61.20.80.40510********TYPICAL PERFORMANCE CURVES (T A = 25ûC)PS7200R-1ATURN-ON TIME vs. FORWARD CURRENTTURN-ON TIME vs. FORWARD CURRENT元器件交易网PS7200R-1ATAPING SPECIFICATIONS (Units in mm)PS7200R-1A-E3PS7200R-1A-E4Reel Outline and DimensionsTape DirectionTape Outline and DimensionsPacking: 900 pcs/reel元器件交易网PS7200R-1AReel Outline and DimensionsTape DirectionTape Outline and DimensionsTAPING SPECIFICATIONS (Units in mm)PS7200R-1A-F3PS7200R-1A-F4元器件交易网PS7200R-1ARECOMMENDED SOLDERING CONDITIONS(1) Infrared reflow soldering •Peak reflow temperature235 °C or below (package surface temperature)•Time of temperature higher than 210 °C 30 seconds or less •Number of reflows Two•FluxRosin flux containing small amount of chlorine(The flux with a maximum chlorine content of 0.2 Wt % is recommended.)Recommended Temperature Profile of Infrared Reflow(2) Dip soldering •Temperature 260 °C or below (molten solder temperature)•Time10 seconds or less•Preheating conditions 100°C or below (package surface temperature)•Number of times One•FluxRosin flux containing small amount of chlorine(The flux with a maximum chlorine content of 0.2 Wt % is recommended.)(3) Cautions •FluxesAvoid removing the residual flux with freon-based and chlorine-based cleaning solvent.Time (s)P a c k a g e S u r f a c e T e m p e r a t u r e T (ûC )A Business Partner of NEC Compound Semiconductor Devices, Ltd.11/11/2002Life Support ApplicationsThese NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale.元器件交易网。