welding-position
钢结构焊接英语术语大全
钢结构焊接英语术语大全以下是一些常见的钢结构焊接英语术语：1. Welding:焊接2. Weld:焊缝3. Joint:焊接接头4. Fillet weld:角焊缝5. Butt weld:对接焊缝6. Fillet size:角焊缝尺寸7. Throat thickness:鞍部厚度8. Penetration:焊透9. Welding position:焊接位置10. Welding procedure:焊接工艺11. Welding current:焊接电流12. Welding voltage:焊接电压13. Welding speed:焊接速度14. Shielding gas:保护气体15. Preheating:预热16. Post-weld heat treatment:焊后热处理17. Groove:槽口18. Bevel:坡口19. Backing strip:补强条20. Welding helmet:焊接面罩21. Welding electrode:焊接电极22. Welding rod:焊条23. Welding wire:焊丝24. Welding machine:焊接机器25. Welding procedure specification (WPS):焊接工艺规范26. Welding inspector:焊接检验员27. Defect:缺陷28. Porosity:孔隙29. Inclusion:夹杂物30. Undercut:侵彻31. Cracking:裂纹32. Slag:焊渣33. Welding consumables:焊接材料34. Arc length:电弧长度35. Arc voltage:电弧电压36. Arc blow:电弧偏转37. Weld quality:焊接质量38. Non-destructive testing (NDT):无损检测39. Visual inspection:目视检验40. Ultrasonic testing (UT):超声波检测41. Radiographic testing (RT):射线检测42. Magnetic particle testing (MT):磁粉检测43. Liquid penetrant testing (PT):渗透检测44. Welder qualification:焊工资格证书45. Welding symbol:焊接符号46. Tack welds:点焊缝47. Crater:焊缝尾部凹坑48. Back gouging:反刮槽49. Weld toe:焊接母材交线处50. Arc welding:弧焊希望对你有所帮助！。
焊接专业名词翻译
1.坡口焊缝的位置区分为：1G、2G、3G、4G、5G、6G、6GR进行区分，分别表示平焊、横焊、立焊、仰焊、管道水平固定焊、管道斜45度固定焊、管道斜45度加障碍带环条件下的6GR焊.2.板材角焊缝分为：1F 2F 3F 4F 分别是船型焊横焊立焊仰焊3.管板或管角焊缝分为：1F 2F 2FR 4F 和5F 分别是45度转动焊横焊(管轴线垂直) 管轴线水平(转动)焊仰焊管轴线水平(固定)焊10 焊接Welding10.1 焊接种类V arieties of Welding电弧焊arc welding电熔焊electric fusion welding (EFW)气熔焊fusion gas welding (FGW)电阻焊electric resistance welding (ERW)有保护的金属电弧焊shielded metal arc welding (SMA W)手工或自动隋性气体保护钨极电弧焊manual and automatic inert gas tungsten arc welding (GTA W)自动埋弧焊automatic submerged arc welding金属极隋性气体保护电弧焊gas metal arc weiding (GMAW)氩弧焊argon-arc welding，气体保护电弧焊gas-shielded arc welding气焊gas welding; flame welding等离子焊plasma welding硬钎焊braze welding电渣焊electroslag welding爆炸焊explosive welding10.2 焊接形式Type of Welding角焊fillet welding间断焊intermittent welding点焊spot welding对焊butt welding搭焊lap welding塞焊plug welding珠焊bead welding槽焊slot welding堆焊build up welding垫板焊backing weld坡口grooveV形坡口V groove单面U形坡口single U grooveK形坡口double bevel grooveX形坡口double V groove双面U形坡口double U grooveU-V组合坡口combination U and V groove 根部间隙root gap焊接符号symbol of weld错边量alignment tolerance10.3 焊接位置Welding Position仰焊overhead welding现场焊field weld (F.W.)封底焊back run welding立焊vertical welding平焊flat welding工厂（车间）焊接shop weld定位焊tack weld跳焊skip welding节距pitch10.4 焊接缺陷Defects of Welding焊接裂纹weld crack根部裂纹root crack微裂纹micro crack错位mismatch弧坑pit; crater焊穿burn through夹渣slag inclusion咬边；咬肉undercut焊瘤overlap气孔porosity, blow hole砂眼blister针孔pin hole严重飞溅excessive spatter未溶合incomplete fusion; lack of fusion根部未焊透incomplete penetration10.5 其它母材；基层金属base metal预热preheating热影响区heat affected zone (HAZ)焊条welding electrode (rod)焊丝welding wire焊药（剂）flux11 热处理Heat Treatment11.1 普通热处理Conventional Heat Treatment退火annealing局部退火spot annealing中间退火process annealing球化退火spheroids annealing等温退火isothermal annealing极软退火dead-soft annealing回水tempering正火normalizing淬火quenching水淬火water quenching油淬火oil quenching等温淬火isothermal quenching断续淬火slack quenching高温淬火hot quenching水冷淬火cold quenching调质quenching and tempering消除应力stress relief时效处理ageing treatment可淬性hardenability过热敏感性superheated susceptivity回火脆性temper brittleness11.2 表面热处理Surface Heat Treatment火焰表面淬火flame surface quenching感应（高频）硬化induction hardening渗碳carbonization渗氮nitridation渗铬chromizing渗铝aluminizing12 检验及试验12.1 检验Inspection焊接检验welding inspection无损检验non-destructive testing (NDT)肉眼检验；外观检验visual inspection着色渗透检验dye penetrant inspection液体渗透检验liquid penetrant test (PT)X射线照相X-ray radiographyγ射线照相gamma radiography射线检验radiographic test (RT)涡流探伤eddy current test (ET)超声波探伤ultrasonic test (UT)磁粉探伤magnetic particle test (MT)荧光渗透检验fluorescent penetrant inspection12.2 试验Test压力试验pressure test水压试验hydraulic test气压试验pneumatic test气密试验air tightness test泄漏试验leak test卤气泄漏试验halogen gas leak test盛水试验full water test真空试验vacuum test拉伸试验tension test弯曲试验bending test冲击试验impact test硬度试验hardness test疲劳试验fatigue test压扁试验flattening test扩口试验flaring test金相试验microscopic test腐蚀试验corrosion test焊接工艺评定试验welding procedure qualification test。
焊接基础知识-焊接位置
Positions位置
1G 2G 3G 5G 6G 6GR
• 1F • 2F • 2FR • 4F • 5F
ห้องสมุดไป่ตู้ 1G Position 1G位置
管子转动，焊条总 是在上面，采split bead或摆动的技术 都是可以接受的。
Pipe rotated, Electrode is always at the top Either a split bead or weave technique may be used
Bead Placement - bottom to top
1、角焊缝/坡口焊缝-纵 向（在紧密的地方可以 采用较小的摆动） 2、焊道位置-从底到上
Fill Pass 填充路径（焊道） Root Pass 打底路径
Cover Pass 盖面路径 Hot Pass 热影响区
Weld Pass
当采用Split bead技术时，所有的工作从底到上的顺 序
WELDING POSITIONS 焊接位置
According to Codes the welding position is essential variable, re-qualification is required to the welders if the are conducting welding to the position they are not qualified based on the codes
管子的轴线是水平的，焊接 时垂直的，焊接前进的方向 是向上或向下，摆动的技术 是最好的。
6G Position 6G 位置
Pipe axis is fixed in position at a 45 degree incline. The position includes flat, horizontal, vertical, and overhead welds.
焊接英语专业术语
汽车骨架英语词汇汽车骨架Automotive skeleton地板 Floor焊接Welding工艺要求Process requirements安全第一Safety first质量要求Quality requirements劳保用品Labor supplies口罩Masks耳塞 Earplug绿色通道 Green Channel钢板型材 Steel plate profiles小于Less than空调出风口Air conditioning vent间隙Gap装配Assembly尺寸要求Size requirements蒙皮Skin并列焊接Tied for welding安全培训Safety training安全隐患Security risks行政楼Administration Building助手Assistant合作愉快Good co-operation行李舱Luggage compartment遵守Comply with培训师Trainers反映Reflect人行横道Crosswalk斑马线Zebra crossing高强度钢 High Strength Steel坚硬 tough埃塞俄比亚Ethiopia埃塞俄比亚联邦民主共和国(The Federal Democratic Republic of Ethiopia焊接英语专业术语1.1 焊接方法焊接方法与设备（Welding process& facility）手工电弧焊(MAW:manual arc welding)电弧焊（arc welding）埋弧电弧焊（SAW：submerged arc welding）气焊（gas welding）氩弧焊（argon arc welding）气体保护电弧焊 CO2保护焊(CO2 shielded arc welding)熔化焊（GMAW—gas metal arc welding）fusion welding 电渣焊(ESW—electroslag welding)激光焊(LW—laster welding)等离子焊(PAW—plasma arc welding)welding pressure welding 冷压焊（CPW—cold pressure welding）锻焊（FW—forge-welding）对焊butt welding电阻焊(RW—resistance welding) 缝焊seam welding点焊spot welding堆焊 overlaying welding平焊 downhand welding/flat welding横焊 horizontal welding立焊 ver tical welding仰焊 overhead welding半自动电弧焊 Semi-automatic arc welding钨极惰性气体保护电弧焊 (TIG) tungsten inert-gas arc welding熔化极惰性气体保护电弧焊（MIG）metal inert-gas arc welding1.2 焊接设备电弧焊机 arc welding machine直流弧焊机 DC arc welding machine氩弧焊机 argon arc welding machine二氧化碳弧焊机 CO2 arc welding machine焊接机头 welding head 行走机构 traveller送丝机构 wire feeder 焊丝盘 wire reel焊钳 electrode holder 焊枪 welding gun等离子弧焊机 plasma arc welding machine等速送丝方式 constant wire-feed system变速送丝方式 alternate wire-feed system点焊机 spot welding machine缝焊机 seam welding machine对焊机 butt resistance welding machine凸焊机 projection welding machine2、焊接材料及焊接工艺（welding materials& procedure）2.1 焊接材料碳钢 carbon steel 合金钢 alloy steel不锈钢 stainless steel耐热钢 high-temprature steel铸铁 casting 铜/黄铜 copper 青铜 bronze 铝 aluminium镁 magnisium 钛 titanium钨 tungsten 镍 nickel铬 chromium2.2 焊接工艺焊接技能 welding technique焊接方法 welding process焊接工艺welding procedure焊接操作 welding operation焊接顺序 welding sequence焊接方向 welding progress焊缝宽度 weld width 焊缝厚度 weld throat焊缝余高 weld reinforcement焊缝长度 weld length 焊接参数 welding parameter焊接电流 welding current 焊接电压 welding voltage焊接速度 welding speed 焊接变形 welding deformation根部间隙 root opening 焊缝正面 face of weld焊缝背面 root surface of weld对接接头 butt joint 角接接头 corner joint焊接性 weldability T型接头 T- joint搭接接头 lap joint 十字接头 cruciform joint后热 postheat 预热 preheat熔深 depth of fusion 焊道 weld bead焊缝成型系数 form factor of the weld焊接经验 welding experience考试机构 examining body焊接工艺规程（WPS） welding procedure specification标准焊接工艺规程（SWPS）standard welding procedure specification 工艺评定记录（PQR） procedure qualification record焊接工艺预规程（pWPS）preliminary welding procedure specification 试验的焊接材料 tested welding materials/consumable焊接管理人员 welding co-ordination/manage personnel预生产焊接试验 pre-production welding test3、焊接缺陷与无损检验（welding defects and non-destructive test）3.1 焊接缺陷夹渣 slag inclusion夹钨 tungsten inclusion夹杂物 inclusion白点 fish eye气孔 porosity烧穿 burn-through咬边 undercut焊接裂纹 welding crack焊瘤 overl ap弧坑裂纹 crater crack弧坑 pit/crater热裂纹 hot crack冷裂纹 cold crack延迟裂纹 delayed crack层状撕裂 lamellar tearing纵向裂纹 longitudinal crack横向裂纹 transverse crack焊接变形 welding deformation未焊透 incomplete penetration, lack of penetration 未熔合 incomplete fusion,lack of penetration4、焊接生产及安全（welding production safety）焊接工作台 welding bench焊接操作台 welding manipulator焊工升降台welder’s lifting platform质量检查 QC=quality control质量保证 QA=quality assurance焊接车间 welding shop面罩 helmet滤光玻璃 filter plate焊工手套 w elder’s glove电焊电缆 Welding cable电焊发动机 Welding generator焊接电源 Welding source电焊工 manual arc welder气焊工 gas welder焊把 weld handle焊接烟尘 welding fume 防护鞋 shielding shoes焊工尘肺 pheumocomsis of welder焊接检验员 weld inspector焊工合格证 welder qualification certification焊工操作资格 welder performance/operation qualification焊接相关英汉词汇argon arc weld 氩弧焊butt weld 对接焊（缝）fillet weld 角焊（缝）full fillet weld 满角焊（缝）spot weld 点焊（缝）weldability 可焊性，焊接性welder 焊工；焊机welding 焊接（法），焊接（的），焊缝attachment weld 固定焊接electric arc weld 电弧焊forehand weld 正手焊（法）gas shield weld 气体保护弧焊oxyacetylene weld 氧（乙炔）焊，气焊plasma-arc weld 等离子弧焊repair weld 补焊scarf weld 斜面焊，两端搭接焊，嵌接焊shield weld 气体保护焊dimensional inspection 尺寸检验girth weld 环形焊缝reinforcement of weld 加强焊缝weld joint 焊缝, 焊接接头butt weld 对接焊缝arc welding 电弧焊filler rod 焊条shield gas 保护气体welding rod 焊条electrode 电焊条horizontal line 水平线welded joint 焊接缝焊接节点gas cutting. 气割arc cutting 电弧切割grind off 磨掉Leveling：校平Fixing：固定Console：控制台material certificate 材料合格证fabrication 加工,制造machining 机械加工solvent 溶剂tack welding 点焊butt welding 对接焊reinforcing pad.补强垫,增强衬板flux 焊剂blind 挡板base material 基底材料flow sheet 流程图witnessed inspections 现场检测drain 排水管identification mark 识别标志fabrication drawing 制造图纸,制作图weld bead 焊缝weld mark 焊痕Seam welding throat thickness 焊缝厚度Weld all around 围焊Weldable copper 可焊复合铜板Weld assembly 焊接件Weld bond 熔合线，焊口Weld cap 焊冒Weld crack 焊接裂缝Weld crater 熔池Weld crosswise 交叉焊接Weld defect 焊接缺陷Welded body 焊接车身Welded construction 焊接结构Welded－contract rectifier 焊接整流器Welded corner joint 角焊接Welded eye 焊眼Welded fissure 焊接裂缝Welded frame 焊接车架，焊接框架Welded metal 焊接金属Welded pipe 焊接管Welded seam 焊缝Welded splice 焊接接头Welded steel 焊接钢Welded steel pipe 焊接钢管Welded structural shape 焊接结构型钢Welded structural 焊接结构Welder construction 焊接结构Welder performance qualification test 焊工技术鉴定试验Welder’s gauntlets 电焊工的长手套Welder’s gloves 电焊工手套Welder’s goggles 焊工护目镜welder’s hand shield 焊工手持护目镜Welder’s head shield 焊工护目帽罩Welder’s health 焊工保健Welder’s helmet 焊工帽罩Welders spatter ease 焊接易飞溅液Weldforged 锻焊Weld gauge 焊缝量规Weld handle 焊把Weld holder 焊接架Welding agent 焊药Welding and cutting torch 焊割两用气焊枪Welding－and－forming mill 成型焊管机Welding apron 焊工的围裙Welding arc 焊弧Welding arc voltage 焊弧电压Welding beading 焊瘤Weldingbead length 焊缝长度Welding bell 碗模（焊管用的），拔管模，喇叭模Welding crack 焊裂缝Welding current 焊接电流Welding cut bit 焊接工具Welding direction 焊接方向Welding dynamo 焊接发电机Welding electrode 电焊条，电焊电极Welding electrode hold 焊条夹Welding equipment 焊接设备Welding flame 焊接火焰Welding flash 弧光灼伤Welding fluid 熔【焊】剂Welding generator电焊发动机Welding glass 黑玻璃Welding gloves焊接手套Welding goggles 焊工护目镜Welding grade argon 焊接极氩，焊接用氩Welding grade gas 焊接级保护气体Welding ground 电焊地线Welding gun 焊枪，喷灯Welding head 焊头，烙铁头，焊接机头Welding inspection 焊接检查Welding iron 烙铁Welding joint 焊接接头Welding lead 焊接引线Welding machine 焊机Welding method 焊接方法Welding－on 焊合，镶焊，焊上Welding operation 焊接操作Welding operator 自动焊工Welding outfit 焊接配备Welding paste 焊接涂料Welding performance 焊接性能Welding position 焊接部位Welding press 焊接压力机Welding pressure 焊接压力Welding procedure 焊接工艺，焊接程序Welding process 焊接法Welding quality 焊接质量Welding regulator 焊接[电流]调节器Welding rod 焊条Welding rolls 焊条辊Welding rules 焊接规则Welding screen 电焊遮光罩Welding seam 焊缝Welding set 焊接装置，电焊机组Welding shop 焊接车间Welding slag 焊渣Welding tongs 焊钳Welding tool 焊接工具Welding torch 焊接喷灯，焊接吹管，焊炬Welding torch pipe 焊枪管Welding wire 焊条，焊丝Welding work 焊工工作Weldless 无焊缝的，无缝的Weldless steel tube 无[焊]缝钢管Weld line 焊接线Weldor 焊工Weld pass 焊接通道Weld penetration 焊穿，焊透深度，熔深Weld rod 焊条Weld rotation 焊缝转角Weld seam 焊缝Weld slope 焊缝倾角Weld strength 焊接强度，焊缝强度Weld surface 焊缝表面Weld trimmer 焊缝清理机Weld up 焊补，焊封Weld wire 包钢铜丝Weldwood 胶合板Weld zone 焊接区Torch cut 火焰切割Sawn 锯Air tight 气密性医用英语一般病情:He feels headache, nausea and vomiting. (他觉得头痛、恶心和想吐。
焊接术语中英对照
焊接用语中英对照焊接专业英语词汇（熔化焊）熔接fusion welding压接pressure welding焊接过程welding process焊接技术welding technique焊接工艺welding technology/procedure焊接操作welding operation焊接顺序welding sequence焊接方向direction of welding焊接位置welding position熔敷顺序build-up sequencedeposition sequence焊缝倾角weld slope/inclination of weld axis焊缝转角weld rotation/angle of rotation平焊位置flat position of welding横焊位置horizontal position of welding立焊位置vertical position of welding仰焊位置overhead position of welding平焊downhand welding/flat position welding横焊horizontal position welding立焊vertical position welding仰焊overhead position welding全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。
如水平固定管所进行的环缝焊接向下立焊vertical down welding/downward welding in the vertical position 向上立焊vertical up welding/upward welding in the vertical position 倾斜焊inclined position welding上坡焊upward welding in the inclined position下坡焊downward welding in the inclined position对接焊butt welding角焊fillet welding搭接焊lap welding船形焊fillet welding in the downhand position/fillet welding in the flat position平角焊horizontal fillet welding立角焊fillet welding in the vertical position仰角焊fillet welding in the overhead position坡口焊groove weldingI形坡口对接焊square butt welding喇叭形坡口焊 flare groove welding卷边焊flanged edge welding纵缝焊接welding of l0ngitudinal seam横缝焊接welding of transverse seam环缝焊接girth welding/ circumferential螺旋缝焊接welding of spiral seam/welding of helical seam 环缝对接焊butt welding of circumferential seam定位焊tack welding单面焊welding by one side双面焊welding by both sides单道焊single pass welding/single run welding多道焊multi-pass welding单层焊single layer welding多层焊multi-layer welding分段多层焊block sequence/ block welding分层多道焊multi-layer and multi-pass welding连续焊continuous welding断续焊intermittent welding打底焊backing weld封底焊back sealing weld盖面焊cosmetic welding深熔焊deep penetration welding摆动焊welding with weaving/weave bead welding前倾焊 foreward welding (英国)/ forehand welding (美国) 后倾焊 backward welding(英国)/ backhand welding(美国)分段退焊backstep welding跳焊skip welding对称焊balanced welding/ balanced welding sequence左焊法leftward welding forehand welding右焊法rightward welding/backhand welding挑弧焊whipping method自动焊automatic welding手工焊manual welding/hand welding车间焊接shop welding工地焊接site welding(英国)/ field welding (美国)拘束焊接restraint welding堆焊surfacing/building up/overlaying隔离层堆焊buttering端部周边焊boxing/end return返修焊rewelding补焊repair welding塞焊plug welding槽焊slot welding衬垫焊welding with backing焊剂垫焊welding with flux backing窄间隙焊narrow-gap welding强制成形焊enclosed welding脉冲电弧焊pulsed are welding电弧点焊arc spot welding螺柱焊stud welding热风焊hot gas welding高能焊high grade energy welding固态焊接solid-state welding单面焊双面成形one-side welding with back formation 焊接条件welding condition焊接工艺参数welding parameter极性polarity正接electrode negative/straight polarity反接electrode positive/reversed polarity运条方式manipulation of electrode焊接电流welding current焊接电流增加时间welding current upslope time焊接电流衰减时间welding current downslope time电流密度current density短路电流short circuit current脉冲电流pulse level/pulse current level脉冲电流幅值pulse current amplitude基值电流background level脉冲频率pulse frequency脉冲焊接电流占空比duty cycle of pulse duration电弧电压arc voltage再引弧电压reignition voltage焊接速度welding speed行走速度rate of travel/travel speed送丝速度wire feed rate线能量heat input/energy input热输入heat input预热preheat后热postheat焊后热处理posweld heat treatment/postheat treatment 预热温度preheat temperature层间温度interpass temperature焊接终了温度finishing temperature后热温度postheating temperature焊丝伸出长度wire extension弧长arc length熔化速度melting rate熔化时间melting time熔化系数melting coefficient熔敷速度rate of deposition/deposition rate熔敷系数deposition coefficient熔敷效率deposition efficiency损失系数loss coefficient飞spatter飞溅率spatter loss coefficient融合比fusion ratio稀释dilution稀释率rate of dilution合金过度系数transfer efficiency/recovery (of an element)坡口groove坡口面groove face坡口面角度angle of bevel (英国)/ bevel angle (美国)坡口角度included angle(英国)/groove angle(美国)坡口高度groove depth钝边root face钝边高度thickness of root face/width of root face根部间隙root gap(英国)/root opening (美国)根部半径root radius/groove radius根部锐边root edge卷边高度height of flange卷边半径radius of flange单面坡口single groove双面坡口double groove坡口形式groove typeI形坡口square grooveV形坡口single V grooveY形坡口single V groove with root face双Y形坡口double Vgroove with root face带钝边U形坡口single U groove带钝边双U形坡口double U grooveVY形坡口single compound angle groove带钝边J形坡口single J groove带钝边双J形坡口double J groove单边V形坡口single bevel groove双V形坡口double V groove不对称双V形坡口 asymmetric double V groove双单边V形坡口 double bevel groove/K groove带垫板V形坡口 V groove with backing/ single V groove with backing 喇叭形坡口flare groove锁底坡口single bevel groove with backing locked坡形板边 tapered edge焊缝 weld接逢 seam焊缝符号 welding symbol焊缝金属 weld metal填充金属 filler metal熔敷金属 deposited metal焊缝表面weld face/ face of weld焊缝背面 back of weld焊缝轴线axis of weld焊缝尺寸 size of weld焊缝宽度weld width/ width of weld焊缝长度 weld length/ length of weld焊缝有效长度 effective length of weld焊缝厚度 throat depth/ throat thickness焊缝计算厚度theoretical throat焊缝实际厚度actual throat熔深penetration/ depth of penetration焊缝成形appearance of weld焊缝成形系数form factor of weld余高 reinforcement/ excess weld metal背面余高root reinforcement削平焊缝flush weld/ weld machined flush对接焊缝butt weld角焊缝fillet焊脚leg/ fillet weld leg角焊缝断面形状profile of fillet weld平形角焊缝flat fillet凸形角焊缝convex fillet weld凹形角焊缝concave fillet weld角焊缝凹度concavity侧面角焊缝side fillet weld/ fillet weld in parallel shear 正面角焊缝front fillet weld/ fillet weld in normal shear 立角焊缝fillet weld in the vertical position横角焊缝fillet weld in the horizontal position平角焊缝fillet weld in the flat position斜角焊缝oblique fillet weld连续焊缝continuous weld断续焊缝intermittent weld连续角焊缝continuous fillet weld断续角焊缝intermittent fillet weld交错断续角焊缝staggered intermittent fillet weld并列断续角焊缝chain intermittent fillet weld端接焊缝edge weld卷边焊缝flanged edge weld塞焊焊缝plug weld纵向焊缝l0ngitudinal weld横向焊缝transverse weld熔化焊环行焊缝girth weld/ circumferential weld螺旋形焊缝spiral weld/ helical weld密封焊缝seal weld承载焊缝strength weld联系焊缝connective weld定位焊缝tack weld焊道bead/ run/ pass焊波ripple焊根weld root/ root of weld焊趾weld toe/ toe封底焊道sealing run (after making main weld)/ back weld打底焊道backing weld (before making main weld)/ back weld根部焊道root pass/ root run填充焊道filling bead盖面焊道cosmetic bead/ cover pass回火焊道temper bead/ annealing bead熔透焊道penetration bead焊层 layer焊接接头welded joint接头形状joint geometry等强匹配接头equalmatching weld joint低强匹配接头undermatching weld joint超强匹配接头overmatching weld joint接头根部root of joint对接接头butt jointI形对接接头square butt jointV形对接接头single V butt jointU形对接接头single U butt jointJ形坡口接头single J butt joint双V形对接接头double V butt joint双单边V形对接接头double bevel butt joint/ K groove butt joint 带钝边U形对接接头double U butt joint带钝边J形坡口接头double J joint角接接头corner jointT形接头T joint斜T形接头inclined T joint十字接头cruciform joint/ cross-shaped joint三联接头joint among three members搭接接头lap joint套管接头muff joint/ sleeve joint双盖板接头double strapped joint盖板接头strapped joint端接接头edge joint卷边接头flanged edge joint锁底对接接头lock butt joint斜对接接头oblique butt joint混合接头mixed joint/ composite joint有间隙接头open joint无间隙接头closed joint焊接电弧welding arc电弧形态arc shape电弧物理行为arc physics behaviour引弧striking arc引弧电压striking voltage电弧气氛arc atmosphere阴极cathode热阴极hot cathode冷阴极cold cathode阴极斑点cathode spot阴极区cathode region阴极区电场强度intensity of the electric field in the cathode region 阴极压降cathode drop阳极anode阳极斑点anode spot斑点压力spot pressure阳极区anode region阳极区电场强度intensity of the electric field in the anode region 阳极压降anode drop弧柱arc column/ arc stream弧柱压降voltage drop in arc column弧柱电位梯度potential gradient in the arc column弧焰arc flame弧心arc core硬电弧forceful arc/ hard arc软电弧soft arc旋转电弧rotating arc脉冲电弧pulsed arc脉冲喷射电弧pulsed spray arc起皱现象puckering phenomena起皱电弧puckering arc起皱临界电流 puckering critical current间接电弧 indirect arc压缩电弧 compressive arc磁控电弧 magnetic controlling arc电弧力 arc force电磁力 electromagnectic force电磁收缩效应 pinch effect电弧飘移 wandering of arc电弧稳定性 arc stability电弧静特性 static characteristic of arc电弧动特性 dynamic characteristic of arc最小电压原理 principle of minimum voltage电弧挺度arc stiffness电弧偏吹 arc blow磁偏吹 magnetic blow阴极清理作用 cleaning action of the cathode电弧自身调节 arc self-regulation挖掘作用 digging action极性效应 polarity effect熔滴 droplet熔滴比表面积 specific surface of droplet熔滴过渡metal transfer过度频率 transition frequency粗滴过渡globular transfer; drop transfer短路过渡short circuiting transfer喷射过渡spray transfer旋转喷射过渡 rotating spray transfer脉冲喷射过渡 pulsed spray transfer爆炸过渡 explosive transfer渣壁过渡 flux wall guided transfer熔池 molten pool沸腾状熔池 boiling molten pool弧坑crater熔渣slag渣系 slag system渣系相图 slag system diagram碱性渣 basic slag酸性渣 acid slag碱度 basicity酸度 acidity长渣 l0ng slag短渣 short slag粘性熔渣 viscous slag氧化物型熔渣 oxide melting slag盐型熔渣 salt melting slag盐-氧化物型熔渣 salt-oxide melting slag熔渣流动性 fluidity of the slag; slag fluidity 熔渣solidified slag多孔焊渣 porous slag玻璃状焊渣 vitreous slag自动脱落焊渣 self-releasing slag脱渣性 slag detachability焊接设备 welding equipment; welding set焊机 welding machine; welder电焊机 electric welding machine; electric welder焊接电源 welding power source焊接热循环 weld thermal cycle焊接温度场 field of weld temperature; weld temperature field 准稳定温度场 quasi-stationary temperature field焊接热源 welding heat source点热源 point heat source线热源 linear heat source面热源 plane heat source瞬时集中热源 instantaneous concentration heat source热效率 thermal efficiency热能集中系数 coefficient of heat flow concentration峰值温度 peak temperature瞬时冷却速度 momentary cooling rate冷却时间 cooling time置换氧化 substitutionary oxydation扩散氧化 diffusible oxydation脱氧 desoxydation先期脱氧 precedent desoxydation扩散脱氧 diffusible desoxydation沉淀脱氧 precipitation desoxydation扩散氢 diffusible hydrogen初始扩散氢 initial diffusible hydrogen100℃残余扩散氢diffusible hydrogen remained at 100℃残余氢 residual hydrogen去氢 dehydrogenation去氢热处理 heat treatment for dehydrogenation脱硫 desulphurization脱磷 dephosphorization渗合金 alloying微量合金化 microalloying一次结晶组织 primary solidification structure二次结晶组织 secondary solidification structure联生结晶 epitaxial solidification焊缝结晶形态 solidification mode in weld-bead结晶层状线 ripple多边化边界 polygonization boundary结晶平均线速度 mean solidification rate针状铁素体 acicular ferrite条状铁素体 lath ferrite侧板条铁素体 ferrite side-plate晶界欣素体 grain boundary ferrite; polygonal ferrite; pro-entectoid ferrite粒状贝氏体 granular bainite板条马氏体 lath martensite过热组织 overheated structure魏氏组织 Widmannst?tten structureM-A组元 martensite-austenite constituent焊件失效分析 failure analysis of weldments冷裂判据 criterion of cold cracking冷裂敏感系数 cold cracking susceptibity coefficient脆性温度区间 brittle temperature range氢脆 hydrogen embrittlement层状偏析 lamellar segregation愈合 healing effect断口金相fractography断口 fracture延性断口 ductile fracture韧窝断口dimple fracture脆性断口 brittle fracture解理断口 cleavage fracture准解理断口 quasi-cleavage fracture氢致准解理断口 hydrogen-embrittlement induced沿晶断口 intergranular fracture穿晶断口 transgranular fracture疲劳断口 fatigue fracture滑移面断口 glide plane fracture断口形貌 fracture apperance断口试验 fracture test宏观断口分析 macrofractography放射区 radical zone纤维区 fibrous zone剪切唇区 shear lip aone焊接性weldability使用焊接性 service weldability工艺焊接性 fabrication weldability冶金焊接性 metallurgical weldability热焊接性 thermal weldability母材 base metal; parent metal焊接区 weld zone焊态 as-welded (AW)母材熔化区 fusion zone半熔化区 partial melting region未混合区 unmixed zone熔合区 bond area熔合线 weld junction (英)；bond line (美)热影响区 heat-affected zone (HAZ)过热区 overheated zone粗晶区 coarse grained region细晶区 fine grained region过渡区 transition zone硬化区 hardened zone碳当量 carbon equivalent铬当量 chromium equivalent镍当量 nickel equivalent舍夫勒组织图 Schaeffler's diagram德龙组织图Del0ng’s diagram连续冷却转变图（CCT图）continuous cooling transformation 裂纹敏感性 cracking sensibility焊接裂纹 weld crack焊缝裂纹 weld metal crack焊道裂纹 bead crack弧坑裂纹crater crack热影响区裂纹 heat-affected zone crack纵向裂纹 l0ngitudinal crack横向裂纹 transverse crack微裂纹 micro-crack; micro-fissure热裂纹 hot crack凝固裂纹 solidification crack晶间裂纹 intercrystalline crack穿晶裂纹 transcrystalline crack多边化裂纹 polygonization crack液化裂纹 liquation crack失延裂纹 ductility-dip crack冷裂纹 cold crack延迟裂纹 delayed crack氢致裂纹 hydrogen-induced crack焊道下裂纹 underbead crack焊根裂纹 root crack焊趾裂纹 toe crack锯齿形裂纹 chevron cracking消除应力处理裂纹 stress relief annealing crack (SR crack) 再热裂纹 reheat crack焊缝晶间腐蚀 weld intercryctalline corrosion刀状腐蚀 knife line attack敏化区腐蚀 weld decay层状撕裂 lamellar tearing焊接性试验 weldability裂纹试验 cracking testIIW裂纹试验 IIW cracking testY形坡口裂纹试验 slit type cracking test分块形槽热裂纹试验 segmented circular groove cracking testH形裂纹试验 H-type cracking test鱼骨形裂纹试验 fishbone cracking test指形裂纹试验 finger (cracking) testT形裂纹试验 Tee type cracking test环形槽裂纹试验 circular-groove cracking test可调拘束裂纹试验 varestraint testBWRA奥氏体钢裂纹试验 BWRA cracking test for austenitie steel圆棒裂纹试验 bar type cracking test; round bar cracking test里海裂纹试验 Lehigh restraint cracking test圆形镶块裂纹试验 circular-path cracking test十字接头裂纹试验 cruciform cracking testZ向窗口拘束裂纹试验 Z-direction window type restraint cracking test G-BOP焊缝金属裂纹试验 G-BOP weld metal crack test巴特尔焊道下裂纹试验 Battelle type underbead cracking testU形拉伸试验 U-tension test缪雷克期热裂纹试验 Murex hot cracking test菲斯柯裂纹试验 FISCO (type) cracking testCTS裂纹试验 controlled thermal severity拉伸拘束裂纹试验（TRC试验）tensile restraint cracking test刚性拘束裂纹试验（RRC试验）rigid restraint cracking test插销试验 implant testTigamajig 薄板焊接裂纹试验 Tigamajing thin plate cracking test焊道纵向弯曲试验 l0ngitudinal-bead test柯麦雷尔弯曲试验 Kommerell bead bend test肯泽尔弯曲试验 Kinzel test缺口弯曲试验 notch bend test热朔性试验 hot-ductility test热影响区冲击试验 impact test of HAZ热影响区模拟试验 synthetic heat-affected zone test最高硬度试验 maximum hardness test落锤试验 NRL (Naval Research Laboratory)测氢试验 Hydrogen test焊接材料电极焊接材料welding consumables电极electrode熔化电极consumable electrode不熔化电极nonconsumable electrode钨电极tungsten electrode焊丝welding wire. Welding rod实心焊丝solid wire渡铜焊丝copper-plating welding wire自保护焊丝self-shielded welding wire药芯焊丝flux-cored wire复合焊丝combined wire堆焊焊丝surfacing welding rod填充焊丝filler wire焊条electrode/ covered electrode焊芯core wire药皮coating (of an electrode)/ covering (of an electrode)涂料coating flux/coating material造气剂gas forming constituents造渣剂slag forming constituents合金剂alloying constituent脱氧剂dioxidizer稳弧剂arc stabilizer粘接剂binder水玻璃water glass水玻璃模数modules of water glass酸性焊条acid electrode高钛型焊条high titania (type) electrode钛钙型焊条lime titania type electrode钛铁矿形焊条ilmenite type electrode氧化铁型焊条iron oxide type electrode/ high iron oxide type electrode 高纤维素型焊条high cellulose (type) electrode石墨型焊条graphite type electrode碱性焊条basic electrode/ lime type covered electrode低氢型焊条low hydrogen type electrode高韧性超低氢焊条high toughness super low hydrogen electrode奥氏体焊条austenitic electrode铁素体焊条ferritic electrode不锈钢焊条stainless steel electrode珠光体耐热钢焊条pearlitic heat resistant steel electrode低温钢焊条low temperature steel electrode/ steel electrode for low temperature铝合金焊条aluminum alloy arc welding electrode铜合金焊条copper-alloy arc welding electrode铜芯铸铁焊条cast iron electrode with steel core纯镍铸铁焊条pure nickel cast iron electrode球墨铸铁焊条electrode for welding spheroidal graphite cast iron铸芯焊条electrode with cast core wire镍基合金焊条nickel base alloy covered electrode蒙乃尔焊条Monel electrode纯铁焊条pure iron electrode渗铝钢焊条alumetized steel electrode高效率焊条high efficiency electrode铁粉焊条iron powder electrode焊接欠缺与检验焊接欠缺welding imperfection焊接缺陷weld defect气孔blowhole/ gas pore针尖状气孔pinhole密集气孔porosity条虫状气孔wormhole裂纹crack表面裂纹surface crack咬边undercut焊瘤overlap凹坑pit烧穿burn through塌陷excessive penetration未焊透incomplete penetration/ lack of penetration 未熔合lack of fusion/ incomplete fusion未焊满incompletely filled weld根部凹陷root concavity电弧擦伤arc scratch夹渣slag inclusion夹杂物inclusion夹钨tungsten inclusion白点fish eye/ flake错边misalignment/ dislocation焊接检验试件test piece试样test specimen面弯试验face bend testing背弯试验root bend test侧弯试验side bend test横弯试验horizontal bend test纵弯试验axial bend test压扁试验squeezing test电阻焊摩擦焊爆炸焊扩散焊超声波焊等电阻焊 resistance welding (RW)点焊 spot welding; resistance spot welding凸焊 projection welding缝焊 seam welding滚点焊 roll-spot welding连续点焊 stitch welding多点焊 multiple spot welding手压点焊 push welding; poke welding脉冲点焊 pulsation spot welding; multiple-impulse welding 双面点焊 direct spot welding单面点焊 indirect spot welding串联点焊 series spot welding多点凸焊multiple projection welding频道进缝焊 step-by-step seam welding压平缝焊 mash seam welding串联缝焊 series seam welding对接缝焊 butt seam welding; foil-butt seam电阻对焊 upset butt welding闪光对焊 flash butt welding (FBW)储能焊 stored energy welding电容储能点焊 condenser discharge spot welding高频电阻焊 high frequency resistance welding冲击电阻焊 percussion welding胶接点焊 spot weld-bonding; weld-bonding闪光 flashing; flash过梁 bridge; lintel顶锻 upsetting; upset夹紧力 clamping force顶锻力 upsetting force; upset force电极压力 electrode force; electrode pressure电极滑移 electrode skid焊接循环 welding cycle预压时间 squeeze time锻压时间 forge-delay time; forge time焊接通电时间（电阻焊）welding time (resistance welding) 预热时间 preheat time加热时间 heat time冷却时间 cool time间歇时间 quench time; chill time回火时间 temper time维持时间 hold time休止时间 off time闪光时间flash time; flashing time顶锻时间 upset time; upsetting time有电顶锻时间 upset current time无电顶锻时间 upset current-off time闪光速度 flashing speed闪光电流 flashing current; flash current顶锻电流 upset current预热电流 preheat current回火电流 temper current调伸长度 initial overhange; extension闪光留量 flash allowance顶锻留量 upset allowance顶锻速度 upset speed电极接触面 electrode contact surface贴合面 faying surface焊点 welding spot熔核 nugget熔核直径 diameter of nugget塑性金属环区corona bond焊透率penetration rate压痕indentation压痕深度depth of indentation压深率indentation ratio翘离sheet separation缩孔shrinkage cavity胡须intrusion电极粘损electrode pick up喷溅splash/ expulsion毛刺fin飞边upset metal/ fin焊点距weld spacing/ spot weld spacing边距edge distance分流shunt current接触电阻contact resistance电阻焊机resistance welding machine点焊机spot welding machine多点焊机multiple spot welding machine移动式点焊机portable spot welding machine缝焊机seam welding machine纵横两用缝焊机universal seam welder对焊机butt resistance welding machine凸焊机projection welding machine三相低频焊机three phase low frequency welder二次整流电阻焊机direct current resistance welder secondary rectification电容储能电阻焊机condenser discharge resistance welder电容储能点焊机condenser type spot welder/ capacitor spot welding machine 工频电阻焊机mains frequency resistance welding machine低频电阻焊机frequency converter resistance welding machine高频焊机high frequency induction welder逆变式电阻焊机inverter type resistance welding machine全波阻焊电源full wave resistance welding power source斩波阻焊电源chopped wave resistance welding power source旋转焊接变压器rotary welding transformerC形点焊钳C-type welding head/ C-type gunX形点焊钳pincer spot welding head/ pliers spot welding head 断续器contactor同步断续器synchronous contactor异步断续器non-synchronous contactor程序控制器sequencer程序时间调节器sequencer timer电极臂arm电极握杆electrode holder电极台板backup die/ bolster电极水冷管electrode cooling tube电极头electrode tip电极帽electrode cap锥头电极truncated tip electrode平头电极flat tip electrode尖头电极pointed tip electrode球面电极radius tip electrode偏心电极offest electrode直电极straight electrode弯电极cranked electrode双弯电极double cranked (swannecked) electrode滚轮电极circular electrode/ welding wheel斜棱滚轮电极bevelled wheel顶锻机构upsetting mechanism电极总行程total electrode stroke工作行程operational stroke辅助行程electrode travel/ electrode stroke臂间距离horn spacing/ throat opening电极臂伸出长度arm extension摩擦焊friction welding (FW)转速friction speed摩擦压力friction pressure/ heating pressure摩擦时间friction time摩擦变形量burn-off length摩擦变形速度burn-off rate停车时间stopping time顶锻变形量forge length顶锻变形速度forge rate摩擦表面friction surface储能摩擦焊fly-wheel type friction welding径向摩擦焊radial friction welding扩散焊diffusion welding (DW)过渡液相扩散焊transient liquid phase diffusion welding 热等静压扩散焊hot isotatic pressure diffusion welding 热轧扩散焊roll diffusion welding扩散缝焊seam diffusion welding超塑成形扩散焊supperplastic forming diffusion bounding 隔离剂buttering material爆炸焊explosive welding (EW)爆炸点焊explosive spot welding爆炸线焊explosive line welding多层板爆炸焊explosive welding of multiplayer plates多层管爆炸焊explosive welding of multiplayer tubes覆板（覆管）cladding plat (tube)/ flyer plate (tube)基板（基管）base plate(tube)/ parent plate (tube)保护层buffer/ protector基础base预置角preset angle间距initial stand-off/ spacing装药量explosive load装药密度charge density/ loading density质量比mass ratio平行法parallel plate configuration角度法preset angle configuration均匀布药average arranging explosive梯形布药gradient arranging explosive爆炸焊参数explosive welding parameters初始参数initial parameters动态参数dynamic parameters界面参数interface parameters爆轰速度detonation velocity覆板速度cladding plate velocity碰撞点impact point碰撞点速度velocity of the impact point弯折角bending angle碰撞角collision angle碰撞压力impact pressure格尼能Gurney energy垂直碰撞normal impact倾斜碰撞oblique impact/ inclined impact对称碰撞symmetrical impact来流upper stream出流down stream再入射流re-entrant jet自清理oneself cleaning结合区bond zone平面结合plane bond波状结合wave-like bond界面波长length of the interfacial wave界面波幅amplitude of the interfacial wave熔化层molten layer熔化袋molten pocket雷管区detonator zone边界效应edge effect焊接性窗口weldability windows焊着率ratio of welding area内爆法internal explosion process外爆法external explosion process半圆柱试验法semi-cylinder experiment method超声波焊ultrasonic welding (UW)超声波点焊ultrasonic spot welding超声波缝焊ultrasonic seam welding超声波点焊机ultrasonic spot welder超声波缝焊机ultrasonic seam welder冷压焊cold pressure welding (CPW)热压焊hot pressure welding热轧焊hot roll welding旋弧压力焊rotating arc pressure welding埋弧压力焊submerged arc pressure welding电渣压力焊electroslag pressure welding气压焊gas pressure welding锻焊forge-welding/ blacksmith welding磁力脉冲焊magnetic-pulse welding焊接专业英语词汇（焊接卫生与安全）焊接烟尘weld fume焊接发尘量total amount of fumes焊接烟尘浓度weld fume concentration焊接烟尘容限浓度threshold limit values of weld fume (TLV)焊接发尘速率weld fume emission rate焊接有害气体welding toxic gases/ weld harmful gases标定卫生空气需要量nominal hygienic air requirement焊工尘肺pheumocomsis of welder焊工锰中毒chronic occupational manganese poisoning of welder 焊工氟中毒fluorosis of welder焊工金属烟热metal fume fever of welder电光性眼炎eye-flash (arc eye)电光性皮炎electro-photo dermatitis电弧紫外线灼伤ultraviolet ray burn防电击装置voltage reducing device 除尘装置dust collection device焊工手套welding gloves护脚welding spats防护鞋shielding shoes。
焊接英语词汇
焊接英语词汇部门： xxx时间： xxx整理范文，仅供参考，可下载自行编辑熔接fusion welding压接pressure welding焊接过程welding process焊接技术welding technique焊接工艺welding technology/procedure焊接操作welding operation焊接顺序welding sequence焊接方向direction of welding焊接位置welding position熔敷顺序build-up sequencedeposition sequence焊缝倾角weld slope/inclination of weld axis焊缝转角weld rotation/angle of rotation平焊位置flat position of welding横焊位置horizontal position of welding立焊位置vertical position of welding仰焊位置overhead position of welding平焊downhand welding/flat position welding横焊horizontal position welding立焊vertical position welding仰焊overhead position welding全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。
如水平固定管所进行的环缝焊接b5E2RGbCAP向下立焊vertical down welding/downward welding in the vertical positionp1EanqFDPw向上立焊vertical up welding/upward welding in the vertical positionDXDiTa9E3d倾斜焊inclined position welding上坡焊upward welding in the inclined position下坡焊downward welding in the inclined position对接焊butt welding角焊fillet welding搭接焊lap welding船形焊fillet welding in the downhand position/fillet welding in the flat positionRTCrpUDGiT平角焊horizontal fillet welding立角焊fillet welding in the vertical position仰角焊fillet welding in the overhead position坡口焊groove weldingI形坡口对接焊square butt welding喇叭形坡口焊 flare groove welding卷边焊flanged edge welding纵缝焊接welding of longitudinal seam横缝焊接welding of transverse seam环缝焊接girth welding/ circumferential螺旋缝焊接welding of spiral seam/welding of helical seam5PCzVD7HxA环缝对接焊butt welding of circumferential seam定位焊tack welding单面焊welding by one side双面焊welding by both sides单道焊single pass welding/single run welding多道焊multi-pass welding单层焊single layer welding多层焊multi-layer welding分段多层焊block sequence/ block welding分层多道焊multi-layer and multi-pass welding连续焊continuous welding断续焊intermittent welding打底焊backing weld封底焊back sealing weld盖面焊cosmetic welding深熔焊deep penetration welding摆动焊welding with weaving/weave bead welding前倾焊 foreward welding (英国>/ forehand welding (美国>后倾焊 backward welding(英国>/ backhand welding(美国>分段退焊backstep welding跳焊skip welding对称焊balanced welding/ balanced welding sequence左焊法leftward welding forehand welding立角焊fillet welding in the vertical position仰角焊fillet welding in the overhead position坡口焊groove weldingI形坡口对接焊square butt welding喇叭形坡口焊 flare groove welding卷边焊flanged edge welding纵缝焊接welding of longitudinal seam横缝焊接welding of transverse seam环缝焊接girth welding/ circumferential螺旋缝焊接welding of spiral seam/welding of helical seamjLBHrnAILg环缝对接焊butt welding of circumferential seam定位焊tack welding单面焊welding by one side双面焊welding by both sides单道焊single pass welding/single run welding多道焊multi-pass welding单层焊single layer welding多层焊multi-layer welding分段多层焊block sequence/ block welding分层多道焊multi-layer and multi-pass welding连续焊continuous welding断续焊intermittent welding打底焊backing weld封底焊back sealing weld盖面焊cosmetic welding深熔焊deep penetration welding摆动焊welding with weaving/weave bead welding前倾焊 foreward welding (英国>/ forehand welding (美国>后倾焊 backward welding(英国>/ backhand welding(美国>分段退焊backstep welding跳焊skip welding对称焊balanced welding/ balanced welding sequence左焊法leftward welding forehand welding焊接电流衰减时间welding current downslope time电流密度current density短路电流short circuit current脉冲电流pulse level/pulse current level脉冲电流幅值pulse current amplitude基值电流background level脉冲频率pulse frequency脉冲焊接电流占空比duty cycle of pulse duration电弧电压arc voltage再引弧电压reignition voltage焊接速度welding speed行走速度rate of travel/travel speed送丝速度wire feed rate线能量heat input/energy input热输入heat input预热preheat后热postheat焊后热处理posweld heat treatment/postheat treatment 预热温度preheat temperature层间温度interpass temperature焊接终了温度finishing temperature后热温度postheating temperature焊丝伸出长度wire extension弧长arc length熔化速度melting rate熔化时间melting time熔化系数melting coefficient熔敷速度rate of deposition/deposition rate熔敷系数deposition coefficient熔敷效率deposition efficiency损失系数loss coefficient飞spatter飞溅率spatter loss coefficient融合比fusion ratio稀释dilution稀释率rate of dilution合金过度系数transfer efficiency/recovery (of an element>坡口groove坡口面groove face坡口面角度angle of bevel (英国>/ bevel angle (美国>坡口角度included angle(英国>/groove angle(美国>坡口高度groove depth钝边root face钝边高度thickness of root face/width of root face根部间隙root gap(英国>/root opening (美国>根部半径root radius/groove radius根部锐边root edge卷边高度height of flange卷边半径radius of flange单面坡口single groove双面坡口double groove坡口形式groove typeI形坡口square grooveV形坡口single V grooveY形坡口single V groove with root face双Y形坡口double Vgroove with root face带钝边U形坡口single U groove带钝边双U形坡口double U groove申明：所有资料为本人收集整理，仅限个人学习使用，勿做商业用途。
焊接相关英汉词汇
焊接相关英汉词汇argon arc weld 氩弧焊butt weld 对接焊（缝）cluster weld 丛聚焊（缝）cold weld 冷焊（缝），冷压接fillet weld 角焊（缝）flash butt weld 闪光对接焊（缝）full fillet weld 满角焊（缝）groove weld 坡口焊（缝）mash seam weld 滚压焊seam weld 滚焊（缝）slot weld 切口焊（缝）spot weld 点焊（缝）tack (positioned) weld 定位【点位】焊（组焊前）weldability 可焊性，焊接性welder 焊工；焊机welding 焊接（法），焊接（的），焊缝atomic hydrogen weld 原子氢焊attachment weld 固定焊接bead weld 堆焊，狭的焊接braze weld 硬【钎】焊，铜焊built-up weld 堆焊down hand weld 俯【水平】焊接electric arc weld 电弧焊flat position weld （顶面）平【卧】焊flow weld 铸（浇）焊forehand weld 正手焊（法）forge weld 锻焊，锻接friction weld 摩擦焊gas shield weld 气体保护弧焊inert-gas metal-arc weld 焊丝惰性气体保护焊oxyacetylene weld 氧（乙炔）焊，气焊percussion weld 冲击焊plasma-arc weld 等离子弧焊repair weld 补焊roll weld 滚压焊scarf weld 斜面焊，两端搭接焊，嵌接焊shield weld 气体保护焊union arc weld 磁性焊剂二氧化碳保护焊unionmelt weld 埋弧（焊剂层下）自动焊weldment 焊接件，焊接装配bonding technology 焊接工艺fillet weld 角焊,填角焊seal welding. 密封焊接ring joint 环接, 围缘接合seal fitting 密封接头, 密封配件weld reinforcement 焊缝补强dimensional inspection 尺寸检验flange gasket 法兰垫片burn through 烧蚀girth weld 环形焊缝reinforcement of weld 加强焊缝weld joint 焊缝, 焊接接头circumferential joint 周圈接缝butt weld 对接焊缝arc welding 电弧焊filler rod 焊条shield gas 保护气体welding rod 焊条welding bead 焊道，熔敷焊道，焊珠electrode 电焊条longitudinal. 纵向的horizontal line 水平线welded joint 焊接缝焊接节点witness test 订货人在场的试验Alignment：对准,定位调整gas cutting. 气割arc cutting 电弧切割grind off 磨掉Leveling：校平Fixing：固定Console：控制台material certificate 材料合格证fabrication 加工,制造post weld heat treatment 焊后热处理flushing 冲洗，填缝arc gouging 电弧刨削machining 机械加工nut 螺母solvent 溶剂tack welding 点焊butt welding 对接焊reinforcing pad.补强垫,增强衬板flux 焊剂blind 挡板gusset plate 角撑板, 加固板base material 基底材料flow sheet 流程图witnessed inspections 现场检测drain 排水管identification mark 识别标志silicone paint 硅树脂油漆fabrication drawing 制造图纸,制作图WPS Works Process Specification 典型工艺规程caulking metal 填隙合金[金属](材料) weld bead 焊缝weld mark 焊痕bonding wire 接合线, 焊线埋弧焊Submerged-arc Welding 电阻焊Resistance Welding 滚焊Seam welding throat thickness 焊缝厚度weldability 可焊性，焊接性Weldable steel 焊接钢Weldability of metal 金属可焊性Weldability test 可焊性试验Weld all around 围焊Weldable copper 可焊复合铜板Weld assembly 焊接件Weld bond 熔合线，焊口Weld cap 焊冒Weld collar 加强焊缝焊瘤Weld crack 焊接裂缝Weld crater 熔池Weld crosswise 交叉焊接Weld decay 焊缝腐蚀，焊接接头晶间Weld defect 焊接缺陷Weld deposit 堆焊，焊缝熔敷Welded all round 沿周边焊接的Welded armor 焊接甲板Welded body 焊接车身Welded bridge 焊接桥Welded bond 焊接轨隙连接器，焊接导接线Welded cathode 焊接阴极Welded chain 焊接链Welded connection 焊接合，焊接头Welded construction 焊接结构Welded－contract rectifier 焊接整流器Welded corner joint 角焊接weldability 可焊性，焊接性Weldable steel 焊接钢Weldability of metal 金属可焊性Weldability test 可焊性试验Weld all around 围焊Weldable copper 可焊复合铜板Weld assembly 焊接件Weld bond 熔合线，焊口Weld cap 焊冒Weld collar 加强焊缝焊瘤Weld crack 焊接裂缝Weld crater 熔池Weld crosswise 交叉焊接Weld decay 焊缝腐蚀，焊接接头晶间Weld defect 焊接缺陷Weld deposit 堆焊，焊缝熔敷Welded all round 沿周边焊接的Welded armor 焊接甲板Welded body 焊接车身Welded bridge 焊接桥Welded bond 焊接轨隙连接器，焊接导接线Welded cathode 焊接阴极Welded chain 焊接链Welded connection 焊接合，焊接头Welded construction 焊接结构Welded－contract rectifier 焊接整流器Welded corner joint 角焊接Welded eye 焊眼Welded fissure 焊接裂缝Welded fitting 焊接式管接头Welded flange 焊接翼缘Welded frame 焊接车架，焊接框架Welded frog 焊接辙差Weld edgewise 沿边焊接Welded metal 焊接金属Welded pipe 焊接管Welded module 焊接微型组件Welded on head 焊制封头，焊制端盖Welded plate 焊合板Welded seam 焊缝Welded shell course 焊接锅炉筒Welded shell ring焊接锅炉筒Welded splice 焊接接头Welded steel 焊接钢Welded steel fabric 焊接钢筋网Welded steel forging 熔焊钢锻件Welded steel pipe 焊接钢管Welded steel pipe pile 焊接钢管桩Welded structural shape 焊接结构型钢Welded structural 焊接结构Welded truss 焊接桁架Welded tube 焊缝[接]管Welded turret 焊合转塔Welded wire fabric 焊接钢丝网Welder 焊机，焊工Welder construction 焊接结构Welder performance qualification test 焊工技术鉴定试验Welder’s gauntlets 电焊工的长手套Welder’s gloves 电焊工手套Welder’s goggles 焊工护目镜welder’s hand shield 焊工手持护目镜Welder’s head shield 焊工护目帽罩Welder’s health 焊工保健Welder’s helmet 焊工帽罩Welders spatter ease 焊接易飞溅液Welder with condenser 带电容弧焊机Welder with taps 抽头式焊机Weld flaw 焊接缺陷，焊接裂纹Weld flush 焊缝隆起Weld flux 焊剂，焊药Weldforged 锻焊Weld gauge 焊缝量规Weld handle 焊把Weld holder 焊接架Welding 焊接法，熔接，定位焊接；粘结Welding agent 焊药Welding alloy 焊接合金Welding and cutting torch 焊割两用气焊枪Welding－and－forming mill 成型焊管机Welding apron 焊工的围裙Welding arc 焊弧Welding arc voltage 焊弧电压Welding assembly 焊接构件Welding base metal 焊条金属Welding beading 焊瘤Weldingbead length 焊缝长度Welding bell 碗模（焊管用的），拔管模，喇叭模Welding bench 焊接工作台Welding blew lamp 焊炬Welding blowpipe 气焊吹管Welding booth 焊接室Welding burner 焊炬喷嘴Welding by both sides 双面焊Welding by forging 锻焊Welding by one side 单面焊Welding cable 电焊电缆，电焊引线Welding characteristics 焊接特性Welding compound 焊【接】剂Welding conditions 焊接规范Welding connector 电缆夹头Welding contactor 电焊接触器Welding control 接触焊机断流器Welding crack 焊裂缝Welding current 焊接电流Welding cut bit 焊接工具Welding deformations 焊接变形Welding direction 焊接方向Welding dynamo 焊接发电机Welding electrode 电焊条，电焊电极Welding electrode hold 焊条夹Welding equipment 焊接设备Welding fixture 焊接夹具Welding flame 焊接火焰Welding flash 弧光灼伤Welding fluid 熔【焊】剂Welding flux 焊剂，焊药Welding force 阻焊加压；电极压力Welding from both sides 双面焊Welding from one side 单面焊Welding furnace 烧结炉Welding gauge 确定焊缝尺寸用样板Welding gang 焊工班，焊接组Welding generator电焊发动机Welding generator with differential excitation 差激电焊发动机Welding generator with split－Poles 裂极电焊发动机Welding glass 黑玻璃Welding gloves焊接手套Welding goggles 焊工护目镜Welding grade argon 焊接极氩，焊接用氩Welding grade gas 焊接级保护气体Welding ground 电焊地线Welding gun 焊枪，喷灯Welding gutter 焊管拉模Welding handle 焊条夹，电极夹钳Welding head 焊头，烙铁头，焊接机头Welding heat 焊热Welding heat input 焊接输入热量Welding helmet 焊工帽罩Welding holder 焊工握把Welding impulse 电焊脉冲Welding inspection 焊接检查Welding iron 烙铁Welding jig 焊接夹具Welding joint 焊接接头Welding lead 焊接引线Welding machine 焊机Welding manipulator 焊件支架Welding metal cracking 焊缝金属裂纹Welding method 焊接方法Welding motor generator 电动旋转式电焊机Welding neck （flange）对焊法兰Welding－on 焊合，镶焊，焊上Welding operation 焊接操作Welding operator 自动焊工Welding outfit 焊接配备Welding paste 焊接涂料Welding performance 焊接性能Welding pipe 焊接管Welding pistol 焊枪Welding point 焊接接头Welding pool 焊接熔池Welding portion 焊接部位，施焊部位Welding position 焊接部位Welding positioner 焊接胎架，可动焊接工作台Welding positioner roller 焊接定位滚轮Welding powder 焊粉Welding power lead 焊接用输电线Welding press 焊接压力机Welding pressure 焊接压力Welding procedure 焊接工艺，焊接程序Welding process 焊接法Welding quality 焊接质量Welding rectifier 电焊整流器Welding regulator 焊接[电流]调节器Welding research council 焊接研究委员会Welding residual stress 焊接残余应力Welding resistor 焊接电阻器Welding rod 焊条Welding rod coating 焊条上的焊药Welding rod core 焊条芯Welding rod extrusion press 焊条自动涂抹机，焊条压涂机Welding rolls 焊条辊Welding rules 焊接规则Welding screen 电焊遮光罩Welding seam 焊缝Welding sequence 焊接程序Welding set 焊接装置，电焊机组Welding set with a surge injector 脉冲稳弧焊接装置Welding set with DC suppression capacitors 电容抑制直流成分的焊接设备Welding set with H.F. ionizer 带高频电离的焊接装置Welding shop 焊接车间Welding slag 焊渣Welding sleeves [焊接用]套轴Welding socket 焊接管套（管接头）Welding source 焊接电源Welding spats 焊接用护脚Welding spatter 焊渣Welding steel 焊接钢Welding stick 焊丝，焊条Welding strain 焊接应变Welding stress 焊接应力Welding symbol 焊接符号，焊接代号Welding table 焊接工作台Welding temperature 焊接温度Welding thermit [铝]热剂（焊接用）welding tip 焊嘴，焊接吹管火口Welding tongs 焊钳Welding tool 焊接工具Welding torch 焊接喷灯，焊接吹管，焊炬Welding torch pipe 焊枪管Welding transformer 电焊变压器Welding tub 焊接熔池Welding wheel 盘状电极Welding wire 焊条，焊丝Welding－wire reel 焊丝卷圈Welding with backing 垫板焊Welding with flux backing 焊剂垫焊Welding with pressure 压焊Welding with weaving 横向摆动焊接Welding work 焊工工作Welding－in nozzle 焊入式喷嘴Welding interface 焊接界面Weld jig 焊接夹具Weld joint 焊缝，焊接接头Weld junction 熔合线，焊口Welding layer 焊接层Weld length 焊缝长度Weldless 无焊缝的，无缝的Weldless connection 非焊接式接头Weldless drawn pipe 拉制无缝管Weldless fitting 非焊接式接头Weldless pipe 无缝管Weldless steel tube 无[焊]缝钢管Weld line 焊接线Weld machined flush 削平补强的焊缝Weld mark 焊接痕，焊波Weldment 焊接件，焊接装配Weld mesh crate 焊接网格Weld metal 焊接金属，焊缝金属Weld metal cracking 焊缝裂纹Weld metal zone 焊接金属熔化区Weld on bottom 底焊Weldor 焊工Weld pass 焊接通道Weld penetration 焊穿，焊透深度，熔深Weld period 焊接时间Weld preparation 焊缝坡口加工Weld puddle 熔池Weld reinforcement 焊缝补强Weld ripple 焊缝波纹Weld rod 焊条Weld rotation 焊缝转角Weld seam 焊缝Weld slope 焊缝倾角Weld strain 焊接应变Weld strength 焊接强度，焊缝强度Weld surface 焊缝表面Weld time [接触焊的]通电时间Weld trimmer 焊缝清理机Weld up 焊补，焊封Weld wire 包钢铜丝Weldwood 胶合板Weld zone 焊接区Lack of fusion 未熔合Sharp edge 锐边Serrated edge 锯齿形边Torch cut 火焰切割Sawn 锯Air tight 气密性。
welding Position
WWW.SPERKOENGINEERING.CO 15° M
Welding Positions
Tabulation of Positions of Groove Welds
© Sperko Engineering 2005
WWW.SPERKOENGINEERING.CO M
Welding Positions
Tabulation of Positions of Groove Welds
Position Diagram Reference Flat Horizontal Overhead Vertical A B C D Inclination of Axis 0 to 15° 0 to 15° 0 to 80° 15 to 80° Rotation of Face 150 to 210° 80 to 150° 210 to 280° 0 to 80° 210 to 360° 80 to 280°
WWW.SPERKOENGINEERING.CO M
Flat Upward Inclined Limit
Weld may incline upward to a limit of 15° 15°
© Sperko Engineering 2005
WWW.SPERKOENGINEERING.CO M
Flat Upward Inclined Limit
How this table and the diagram on the previous page work are shown in the following diagrams
© Sperko Engineering 2005 WWW.SPERKOENGINEERING.CO M