风力发电术语中英文对照

风电专业术语英文对照及解释

风电专业术语英文对照及解释风电专业术语中英对照及解释经电气网小编整理，下面是有关风电的一些专业术语的英汉对照及解释，希望对各位有用哦。

1.风能 /wind energy 空气流动所具有的能量。

2.风能资源 /wind energy resources 大气沿地球表面流动而产生的动能资源。

3.空气的标准状态 /standard atmospheric state 空气的标准状态是指空气压力为101 325Pa，温度为15℃（或绝对288.15K），空气密度1.225kg/m 3 时的空气状态。

4.风速/wind speed 空间特定点的风速为该点空气在单位时间内所流过的距离。

5.平均风速 /average wind speed 给定时间内瞬时风速的平均值。

6.年平均风速 /annual average wind speed 时间间隔为一整年的瞬时风速的平均值。

7.最大风速 /maximum wind speed 10分钟平均风速的最大值。

8.极大风速 /extreme wind speed 瞬时风速的最大值。

9.阵风 /gust 超过平均风速的突然和短暂的风速变化。

10.年际变化/inter-annual variation 以30年为基数发生的变化。

风速年际变化是从第1年到第30年的年平均风速变化。

11.[风速或风功率密度]年变化 /annual variation 以年为基数发生的变化。

风速（或风功率变化）年变化是从1月到12月的月平均风速（或风功率密度）变化。

12.[风速或风功率密度]日变化 /diurnal variation 以日为基数发生的变化。

月或年的风速（或风功率密度）日变化是求出一个月或一年内，每日同一钟点风速（或风功率密度）的月平均值或年平均值，得到0点到23点的风速（或风功率密度）变化。

风切变 /wind shear 风速在垂直于风向平面内的变化。

13.风切变指数 /wind shear exponent 用于描述风速剖面线形状的幂定律指数。

风力发电术语汉英A对照

风力发电术语汉英A对照2007-10-9 23:29:28 东盟商机信息中心绝对湿度absolute humidity加速实验accelerated test加速accelerating加速度幅值acceleration amplitude验收实验acceptance test精度（风力发电机组）accuracy(for WTGS) 确认acknowledgement 声的基准风速acoustic reference wind speed 临界功率activation power(for wind turbines) 临界转速activation rotational speed 有功电流active current 有功功率active power 主动偏航active yawing 齿轮的变位addendum modification on gears 地址address 可调钳adjustable pliers 调整板adjusting plate 风轮空气动力特性aerodynamic characteristics of rotor 气动弦线aerodynamic chord of airfoil 老化实验ageing tests 空气制动系air braking system 空气湿度air humidity 透气性air permeability 翼型airfoil 接闪器air-termination system 告警alarm 交流电流alternating current 交流电机alternating current machine 交流电压alternating voltage 海拔altitude 环境温度ambient temperature 放大器amplifier 幅值amplitude 模拟信号analog signal 模拟盘analogue board 模拟操纵analogue control 叶片几何攻角angle of attack of blade 风轮仰角angle of rotor shaft 年平均annual average 年平均风速annual average wind speed 年发电量annual energy production 年最高日平均温度annual extreme daily mean of temperature 年最高annual maximum 年转变annual variation 视在声功率级apparent sound power level 灭弧装置arc-control device 叶片展弦比aspect ratio 异步电机asynchronous generator 异步电机asynchronous machine 衰减attenuation 自耦变压器auto-transformer 辅助电路auxiliary circuit 辅助装置auxiliary device 有效性availability 可利用率（风力发电机组）availability(for WTGS) 平均噪声average noise level 轴向齿距axial pitch风力发电机名词术语汉英对照(1)2020年06月08日礼拜日14:21风力机wind turbine风电场wind power station wind farm 风力发电机组wind turbine generator system WTGS 水平轴风力机horizontal axis wind turbine垂直轴风力机vertical axis wind turbine轮毂（风力机）hub (for wind turbine)机舱nacelle支撑结构support structure for wind turbine关机shutdown for wind turbine正常关机normal shutdown for wind turbine紧急关机emergency shutdown for wind turbine空转idling锁定blocking停机parking静止standstill制动器brake停机制动parking brake风轮转速rotor speed控制系统control system保护系统protection system偏航yawing设计和安全参数design situation设计工况design situation载荷状况load case外部条件external conditions设计极限design limits极限状态limit state使用极限状态serviceability limit states极限限制状态ultimate limit state最大极限状态ultimate limit state安全寿命safe life严重故障catastrophic failure潜伏故障latent fault dormant failure风特性风速wind speed风矢量wind velocity旋转采样风矢量rotationally sampled wind velocity 额定风速rated wind speed切入风速cut-in speed切出风速cut-out speed年平均annual average年平均风速annual average wind speed平均风速mean wind speed极端风速extreme wind speed安全风速survival wind speed参考风速reference wind speed风速分布wind speed distribution瑞利分布RayLeigh distribution威布尔分布Weibull distribution风切变wind shear风廓线风切变律wind profile wind shear law 风切变指数wind shear exponent对数风切变律logarithmic wind shear law风切变幂律power law for wind shear下风向down wind上风向up wind阵风gust粗糙长度roughness length湍流强度turbulence intensity湍流尺度参数turbulence scale parameter湍流惯性负区inertial sub-range风场wind site测量参数measurement parameters测量位置measurement seat最大风速maximum wind speed风功率密度wind power density风能密度wind energy density日变化diurnal variation年变化annual variation轮毂高度hub height风能wind energy标准大气状态standard atmospheric state风切变影响influence by the wind shear阵风影响gust influence风速频率frequency of wind speed环境environment工作环境operational environment气候climate海洋性气候ocean climate大陆性气候continental climate露天气候open-air climate室内气候indoor climate极端extreme日平均值daily mean极端最高extreme maximum年最高annual maximum年最高日平均温度annual extreme daily mean of temperature月平均温度mean monthly temperature风力发电机名词术语汉英对照(1)风力机wind turbine风电场wind power station wind farm风力发电机组wind turbine generator system WTGS水平轴风力机horizontal axis wind turbine垂直轴风力机vertical axis wind turbine轮毂（风力机）hub (for wind turbine)机舱nacelle支撑结构support structure for wind turbine关机shutdown for wind turbine正常关机normal shutdown for wind turbine紧急关机emergency shutdown for wind turbine空转idling锁定blocking停机parking静止standstill制动器brake停机制动parking brake风轮转速rotor speed操纵系统control system爱惜系统protection system偏航yawing设计和平安参数design situation 设计工况design situation载荷状况load case外部条件external conditions设计极限design limits极限状态limit state利用极限状态serviceability limit states 极限限制状态ultimate limit state 最大极限状态ultimate limit state平安寿命safe life严峻故障 catastrophic failure暗藏故障latent fault dormant failure风特性风速wind speed风矢量wind velocity旋转采样风矢量rotationally sampled wind velocity 额定风速rated wind speed切入风速cut-in speed切出风速cut-out speed年平均annual average年平均风速annual average wind speed平均风速mean wind speed极端风速extreme wind speed平安风速survival wind speed参考风速reference wind speed风速散布wind speed distribution瑞利散布RayLeigh distribution威布尔散布Weibull distribution风切变wind shear风廓线风切变律wind profile wind shear law 风切变指数wind shear exponent对数风切变律logarithmic wind shear law风切变幂律power law for wind shear下风向down wind上风向up wind阵风gust粗糙长度roughness length湍流强度turbulence intensity湍流尺度参数turbulence scale parameter 湍流惯性负区inertial sub-range风场wind site测量参数measurement parameters测量位置measurement seat最大风速maximum wind speed风功率密度wind power density风能密度wind energy density日转变diurnal variation年转变annual variation轮毂高度hub height风能wind energy标准大气状态standard atmospheric state 风切变阻碍influence by the wind shear 阵风阻碍gust influence风速频率frequency of wind speed环境environment工作环境operational environment气候climate海洋性气候ocean climate大陆性气候continental climate露天气候open-air climate室内气候indoor climate极端extreme日平均值daily mean极端最高extreme maximum年最高annual maximum年最高日平均温度annual extreme daily mean of temperature 月平均温度mean monthly temperatureabrasive研磨料abrasive disc磨料盘accumulator 储压罐acetone丙酮activation活动，赋活，激活，活化，鼓励，启用acute angle锐角adhesive 带粘性的, 胶粘, 粘合剂adjustable spanner 活动扳手admixture 混合, 混合物adversely逆地, 反对地adze扁斧aerial航空的, 生活在空气中的, 空气的, 挺拔的,天线aerosol 浮质,气溶胶, 气雾剂, 烟雾剂aggregate 合计, 共计, 集合体aggressively 入侵地, 攻势地air inlet通风口air-cushion vehicle气垫船air gap气隙align对准，校直，定位；调,排列, 使结盟, 使成一行alkali-sensitive碱性感测allen key 六方allen wrench 六方扳手alloy 合金alteration变更, 改造alternator 交替符；交流发电机ammeter安培计，电流表anaerobic没有空气而能生活的, 厌氧性的anchor 锚, 抛锚, 锚定aneroid barometer无液气压表, 无液晴雨angle grinder角锉angle plate角盘annealing 退火annulus环面anode阳极, 正极anodization阳极氧化antenna 天线；触角antifriction减低或避免磨擦之物, 润滑剂anvil铁砧approximate近似, 接近, 约计adjarbor 树阴；凉亭；藤架〈机〉柄轴；心轴arc 弧, 弓形, 拱,电弧arc welding 电弧焊archimedean screw阿基米德螺线arrmature 电枢articulated接合,链接,有关节的assemble集合, 聚集, 装配assorted files分类排列；相匹配(文件)assume假定, 假想, 采取, 呈现attenuation变薄, 稀薄化, 变细, 衰减auger打孔钻，螺丝钻averagen. 平均, 平均水平, 平均数, 海损, 一样的, 通常的awln锥子axe斧, (经费的)大削减axle. 轮轴, 车轴Bback saw背锯backlash反冲，无效行程；间隙，偏移；退ball bearing滚珠轴ball saddle滚珠支撑ball-peen hammerband区；带，波段带子, 镶边, 波段, 队, 乐队. 联合, 结合bandsaw用带锯锯bar magnet磁条barometer气压计；晴雨表battery power drill电池钻beach海边；湖滨；河滩bead 珠子, 水珠beam compass长臂圆规beam trammel骨架bearer 支架，托架，支座，载体bell crank曲柄belting制带的材料, 带类, 调带装置bessemer酸性转炉钢bessemer converter . 酸性转炉,贝塞麦转炉bevel gear斜角；斜齿轮bevel-edge shisel斜缘薄钢板biconcave lens两面凹镜biconvex lens两面凸镜bifurcated rivetbimetallic双金属的bin二进制；双态bit 位, 比特blade for iron saw剧刃blast 强风，过载blast furnace鼓风炉blast cleaning皮老虎bleed 放出(液体，气体等)；漏出，漏入，泄漏，色料扩散bleeder valve 溢流阀block and tackle滑轮组blowlamp喷灯blowpipe吹风管blowtorch 吹管, 喷灯board 底板，板boiler锅炉；煮器；烧水器bolt螺栓，螺钉，支持，维持bone 骨剔除bonnet软帽,汽车发动机罩bore钻孔,钻bottom dead-centrebow-spring compassbox spanner管钳子box spanner insetbrac支柱, 带子, 振作精神bracket托架, 括弧, 支架brad曲头钉bradawl小锥Brakebrake lining闸, 刹车的衬里, 内层, 衬套brake shoe 闸轨branch of joint连接分支brass黄铜, 黄铜制品,brazing铜焊breast drillbreather 呼吸者, 喘息者, 猛烈的运动bricklayer’s hammerbubble 磁泡，水泡，气泡bucket桶, 一桶的量, 铲斗Buffing wheelbulk大小, 体积, 大量, 大多数, 散装bulkhead隔壁, 防水壁bulldozer 推土机bunsen burner 本生灯burr芒刺；刺果植物；针球burstn. 突然破裂, 暴发, 脉冲bursting discbush 矮树丛, (机械)衬套bushing轴衬, 套管Ccabinet screw driver cable bundle 束，光纤束；捆，卷cable reel电缆盘cable shear电缆剪cable shoes电缆靴cable tie电缆带calibration标度, 刻度, 校准caliper测径器, 卡钳, 弯脚器cam凸轮camber 拱形camshaft凸轮轴cantilever伸臂，悬臂；悬臂梁cap帽,罩cap nut螺冒capaciron电容汞弧管capacitance电容；电容量capstan lathe绞盘车床carburettor 汽化器cardan shaft万向轴cartridge额盒式磁盘[带](机)；夹头cast投；掷；抛casting. 铸件, 铸造castle nut城堡螺母catalyst 催化剂，触媒cathode 阴极cathode-ray tube阴极射线管catwalk桥上人行道, 狭小通道caulking 填...以防漏风力机wind turbine风力发电机组wind turbine generator system;WTGS 水平轴风力机horizontal axis wind turbine垂直轴风力机vertical axis wind turbine轮毂（风力机）hub (for wind turbine)机舱nacelle支撑结构support structure for wind turbine关机shutdown for wind turbine正常关机normal shutdown for wind turbine紧急关机emergercy shutdown for wind turbine空转idling锁定blocking停机parking静止standstill制动器brake停机制动parking brake风轮转速rotor speed控制系统control system保护系统protection system偏航yawing设计和安全参数design situation载荷状况load case外部条件external conditions设计极限design limits极限状态limit state使用极限状态serviceability limit states最大极限状态ultimate limit state安全寿命safe life严重故障 catastrophic failure潜伏故障latent fault;dormant failure风速wind speed风矢量wind velocity旋转采样风矢量rotationally sampled wind velocity 额定风速rated wind speed切入风速cut-in speed切出风速cut-out speed年平均风速annual average wind speed平均风速mean wind speed极端风速extreme wind speed安全风速survival wind speed参考风速reference wind speed风速分布wind speed distribution瑞利分布RayLeigh distribution威布尔分布Weibull distribution风切变wind shear风廓线风切变律wind profile;wind shear law风切变指数wind shear exponent对数风切变律logarithmic wind shear law风切变幂律power law for wind shear下风向down wind上风向up wind阵风gust粗糙长度roughness length湍流强度turbulence intensity湍流尺度参数turbulence scale parameter湍流惯性负区inertial sub-range互联interconnection额定功率rated power最大功率maximum power电网连接点network connection point电力汇集系统power collection system电场电器设备site electrical facilities功率特性power performance静电功率输出net electric power output功率系数power performance自由流风速free stream wind speed扫掠面积swept area轮毂高度hub height测量功率曲线measurement power curve外推功率曲线extrapolated power curve年发电量annual energy production可利用率availability数据组功率特性测试data set for power performance measurement 精度accuracy测量误差uncertainty in measurement分组方法method of bins测量周期measurement period测量扇区measurement sector日变化diurmal variations浆距角pitch angle距离常数distance constant试验场地test site气流畸变flow distirtion障碍物obstacles复杂地形带complex terrain风障wind break声压级sound pressure level声级weighted sound pressure level; sound level视在声功率级apparent sound power level指向性directivity音值tonality声的基准面风速acoustic reference wind speed 标准风速standardized wind speed基准高度reference height基准粗糙长度reference roughness length基准距离reference distance掠射角grazing angle风轮风轮wind rotor风轮直径rotor diameter风轮扫掠面积rotor swept area风轮仰角tilt angle of rotor shaft风轮偏航角yawing angle of rotor shaft风轮额定转速rated turning speed of rotor风轮最高转速maximum turning speed of rotor 风轮尾流rotor wake尾流损失wake losses风轮实度rotor solidity实度损失solidity losses叶片数numble of blades叶片blade等截面叶片constant chord blade变截面叶片variable chord blade叶片投影面积projected area of blade叶片长度length of blade叶根root of blade叶尖tip of blade叶尖速度tip speed浆距角pitch angle翼型airfoil前缘leading edge后缘tailing edge几何弦长geometric chord of airfoil平均几何弦长mean geometric of airfoil气动弦线aerodynamic chord of airfoil翼型厚度thickness of airfoil翼型相对厚度relative thickness of airfoil厚度函数thickness function of airfoil中弧线mean line弯度degree of curvature翼型族the family of airfoil弯度函数curvature function of airfoil叶片根梢比ratio of tip-section chord to root-section chord叶片展弦比 aspect ratio叶片安装角setting angle of blade叶片扭角twist of blade叶片几何攻角angle of attack of blade叶片损失blade losses叶尖损失tip losses颤振flutter迎风机构orientation mechanism调速机构regulating mechamism风轮偏测式调速机构regulating mechanism of turning wind rotor out of the wind sideward 变浆距调速机构regulating mechanism by adjusting the pitch of blade整流罩nose cone顺浆feathering阻尼板spoiling flap风轮空气动力特性aerodynamic chatacteristics of rotor叶尖速度比tip-speed ratio额定叶尖速度比rated tip-speed ratio升力系数lift coefficient阻力系数drag coefficient推或拉力系数thrust coefficient偏航系统滑动制动器sliding shoes偏航yawing主动偏航active yawing被动偏航passive yawing偏航驱动yawing driven解缆untwist塔架tower独立式塔架free stand tower拉索式塔架guyed tower塔影响效应influence by the tower shadow <<功率特性测试>>功率特性power performance净电功率输出net electric power output 功率系数power coefficient自由流风速free stream wind speed扫掠面积swept area测量功率曲线measured power curve外推功率曲线extrapolated power curve 年发电量annual energy production数据组data set可利用率availability精度accuracy测量误差uncertainty in measurement分组方法method of bins测量周期measurement period测量扇区measurement sector距离常数distance constant试验场地test site气流畸变flow distortion复杂地形地带complex terrion风障wind break声压级sound pressure level声级weighted sound pressure level视在声功率级apparent sound power level指向性directivity音值tonality声的基准风速acoustic reference wind speed标准风速standardized wind speed基准高度reference height基准粗糙长度reference roughness基准距离reference distance掠射角grazing angle比恩法method of bins标准误差standard uncertainty风能利用系数rotor power coefficient力矩系数torque coefficient额定力矩系数rated torque coefficient起动力矩系数starting torque coefficient最大力矩系数maximum torque coefficient过载度ratio of over load风力发电机组输出特性output characteristic of WTGS调节特性regulating characteristics平均噪声average noise level机组效率efficiency of WTGS使用寿命service life度电成本cost per kilowatt hour of the electricity generated by WTGS 发电机同步电机synchronous generator异步电机asynchrinous generator感应电机induction generator转差率slip瞬态电流transient rotor笼型cage绕线转子wound rotor绕组系数winding factor换向器commutator集电环collector ring换向片commutator segment励磁响应excitation response制动系统制动系统braking制动机构brake mechanism正常制动系normal braking system紧急制动系emergency braking system空气制动系air braking system液压制动系hydraulic braking system电磁制动系electromagnetic braking system 机械制动系mechanical braking system辅助装置auxiliary device制动器释放braking releasing制动器闭合brake setting液压缸hydraulic cylinder溢流阀relief valve泻油drain齿轮马达gear motor齿轮泵gear pump电磁阀solenoid液压过滤器hydraulic filter液压泵hydraulic pump液压系统hydraulic system油冷却器oil cooler压力控制器pressure control valve 压力继电器pressure switch减压阀reducing valve安全阀safety valve设定压力setting pressure切换switching旋转接头rotating union压力表pressure gauge液压油hydraulic fluid液压马达hydraulic motor油封oil seal刹车盘brake disc闸垫brake pad刹车油brake fluid闸衬片brake lining。

风力发电机名词术语汉英对照

风力发电机名词术语汉英对照(1)2008年06月08日星期日14:21风力机wind turbine风电场wind power station wind farm 风力发电机组wind turbine generator system WTGS 水平轴风力机horizontal axis wind turbine垂直轴风力机vertical axis wind turbine轮毂（风力机）hub (for wind turbine)机舱nacelle支撑结构support structure for wind turbine关机shutdown for wind turbine正常关机normal shutdown for wind turbine紧急关机emergency shutdown for wind turbine空转idling锁定blocking停机parking静止standstill制动器brake停机制动parking brake风轮转速rotor speed控制系统control system保护系统protection system偏航yawing设计和安全参数design situation设计工况design situation载荷状况load case外部条件external conditions设计极限design limits极限状态limit state使用极限状态serviceability limit states极限限制状态ultimate limit state最大极限状态ultimate limit state安全寿命safe life严重故障catastrophic failure潜伏故障latent fault dormant failure风特性风速wind speed风矢量wind velocity旋转采样风矢量rotationally sampled wind velocity 额定风速rated wind speed切入风速cut-in speed切出风速cut-out speed年平均annual average年平均风速annual average wind speed平均风速mean wind speed极端风速extreme wind speed安全风速survival wind speed参考风速reference wind speed风速分布wind speed distribution瑞利分布RayLeigh distribution威布尔分布Weibull distribution风切变wind shear风廓线风切变律wind profile wind shear law 风切变指数wind shear exponent对数风切变律logarithmic wind shear law风切变幂律power law for wind shear下风向down wind上风向up wind阵风gust粗糙长度roughness length湍流强度turbulence intensity湍流尺度参数turbulence scale parameter湍流惯性负区inertial sub-range风场wind site测量参数measurement parameters测量位置measurement seat最大风速maximum wind speed风功率密度wind power density风能密度wind energy density日变化diurnal variation年变化annual variation轮毂高度hub height风能wind energy标准大气状态standard atmospheric state风切变影响influence by the wind shear阵风影响gust influence风速频率frequency of wind speed环境environment工作环境operational environment气候climate海洋性气候ocean climate大陆性气候continental climate露天气候open-air climate室内气候indoor climate极端extreme日平均值daily mean极端最高extreme maximum年最高annual maximum年最高日平均温度annual extreme daily mean of temperature 月平均温度mean monthly temperatureabrasive研磨料abrasive disc磨料盘accumulator储压罐acetone丙酮activation活动，赋活，激活，活化，激励，启用acute angle锐角adhesive带粘性的,胶粘,粘合剂adjustable spanner活动扳手admixture混合,混合物adversely逆地,反对地adze扁斧aerial航空的,生活在空气中的,空气的,高耸的,天线aerosol浮质,气溶胶,气雾剂,烟雾剂aggregate合计,总计,集合体aggressively侵略地,攻势地air inlet通风口air-cushion vehicle气垫船air gap气隙align对准，校直，定位；调,排列,使结盟,使成一行alkali-sensitive碱性感测allen key六方allen wrench六方扳手alloy合金alteration变更,改造alternator交替符；交流发电机ammeter安培计，电流表anaerobic没有空气而能生活的,厌氧性的anchor锚,抛锚,锚定aneroid barometer无液气压表,无液晴雨angle grinder角锉angle plate角盘annealing退火annulus环面anode阳极,正极anodization阳极氧化antenna天线；触角antifriction减低或防止磨擦之物,润滑剂anvil铁砧approximate近似,接近,约计adjarbor树阴；凉亭；藤架〈机〉柄轴；心轴arc弧,弓形,拱,电弧arc welding电弧焊archimedean screw阿基米德螺线arrmature电枢articulated接合,链接,有关节的assemble集合,聚集,装配assorted files分类排列；相匹配(文件)assume假定,设想,采取,呈现attenuation变薄,稀薄化,变细,衰减auger打孔钻，螺丝钻averagen.平均,平均水平,平均数,海损,一般的,通常的awln锥子axe斧, (经费的)大削减axle.轮轴,车轴Bback saw背锯backlash反冲，无效行程；间隙，偏移；退ball bearing滚珠轴ball saddle滚珠支撑ball-peen hammerband区；带，波段带子,镶边,波段,队,乐队.联合,结合bandsaw用带锯锯bar magnet磁条barometer气压计；晴雨表battery power drill电池钻beach海滨；湖滨；河滩bead珠子,水珠beam compass长臂圆规beam trammel骨架bearer支架，托架，支座，载体bell crank曲柄belting制带的材料,带类,调带装置bessemer酸性转炉钢bessemer converter .酸性转炉,贝塞麦转炉bevel gear斜角；斜齿轮bevel-edge shisel斜缘薄钢板biconcave lens两面凹镜biconvex lens两面凸镜bifurcated rivetbimetallic双金属的bin二进制；双态bit位,比特blade for iron saw剧刃blast强风，过载blast furnace鼓风炉blast cleaning皮老虎bleed放出(液体，气体等)；漏出，漏入，泄漏，色料扩散bleeder valve溢流阀block and tackle滑轮组blowlamp喷灯blowpipe吹风管blowtorch吹管,喷灯board底板，板boiler锅炉；煮器；烧水器bolt螺栓，螺钉，支持，维持bone骨剔除bonnet软帽,汽车发动机罩bore钻孔,钻bottom dead-centrebow-spring compassbox spanner管钳子box spanner insetbrac支柱,带子,振作精神bracket托架,括弧,支架brad曲头钉bradawl小锥Brakebrake lining闸,刹车的衬里,内层,衬套brake shoe闸轨branch of joint连接分支brass黄铜,黄铜制品,brazing铜焊breast drillbreather呼吸者,喘息者,剧烈的运动bricklayer’s hammerbubble磁泡，水泡，气泡bucket桶,一桶的量,铲斗Buffing wheelbulk大小,体积,大批,大多数,散装bulkhead隔壁,防水壁bulldozer推土机bunsen burner本生灯burr芒刺；刺果植物；针球burstn.突然破裂,爆发,脉冲bursting discbush矮树丛, (机械)衬套bushing轴衬,套管Ccabinet screw drivercable bundle束，光纤束；捆，卷cable reel电缆盘cable shear电缆剪cable shoes电缆靴cable tie电缆带calibration标度,刻度,校准caliper测径器,卡钳,弯脚器cam凸轮camber拱形camshaft凸轮轴cantilever伸臂，悬臂；悬臂梁cap帽,罩cap nut螺冒capaciron电容汞弧管capacitance电容；电容量capstan lathe绞盘车床carburettor汽化器cardan shaft万向轴cartridge额盒式磁盘[带](机)；夹头cast投；掷；抛casting.铸件,铸造castle nut城堡螺母catalyst催化剂，触媒cathode阴极cathode-ray tube阴极射线管catwalk桥上人行道,狭小通道caulking填...以防漏。

风力发电机组中英文词汇对照

风力发电机组中英文词汇对照Aa.t.c.system 加工中心机刀库abrasive disc 磨料盘abscissa axis 横坐标absolute encoder 绝对式编码器absolute humidity 绝对湿度ac motor 交流环电动机accelerated test 加速试验accelerating 加速acceleration amplitude 加速度幅值accelerometer 加速度传感器acceptance test 验收试验accumulator 储压罐accuracy 精度acetone 丙酮acknowledgement 确认acoustic reference wind speed 声的基准风速activation power (for wind turbines) 临界功率activation rotational speed 临界转速activation 活动，赋活，激活，活化，激励，启用active (passive) circuit elements 有（无）源电路元件active component 有功分量active current 有功电流active in respect to 相对….呈阻性active power 有功功率active yawing 主动偏航acute angle 锐角addendum modification on gear 齿轮的变位address 地址adhesive 带粘性的，胶粘，粘合剂adjustable spanner 活动扳手adjusting plate 调整板admittance 导纳admixture 混合，混合物adversely 逆地，反对地adze 扁斧aerial航空的，生活在空气中的，空气的，高耸的，天线aerodynamic characteristics of rotor 风轮空气动力特性aerodynamic chord of airfoil 气动弦线aerosol 浮质，气溶胶，气雾剂，烟雾剂ageing tests 老化试验aggregate 合计，总计，集合体aggressively 侵略地，攻势地air braking system 空气制动系统air gap 气隙air header 集气管air humidity 空气湿度air inlet 通风口air permeability 透气性air set 空气中凝固，常温自硬自然硬化air-cushion 空气垫airfoil 翼型air-gap flux distribution 气隙磁通分布air-gap flux 气隙磁通air-gap line 气隙磁化线air-termination system 接闪器alarm 报警algebraic 代数的algorithmic 算法的align 对准，校直alignment 对准，定位调整alkali-sensitive 碱性感测allen key 六方allen wrench 六方扳手alloy 合金alloy 合金alteration变更，改造alternating current machine 交流电机alternating current 交流电流alternating voltage 交流电压altitude 海拔aluminum continuous melting & holding furnaces 连续溶解保温炉ambient temperature 环境温度ammeter电流表ampere-turns 安匝(数)amplidyne 微场扩流发电机amplifier panel 放大器盘amplifier 放大器amplitude modulation(am 调幅amplitude 幅值anaerobic没有空气而能生活的，厌氧性的analog input terminals 模拟量输入端子analog signal 模拟信号analogue board 模拟盘analogue control 模拟控制analyzer分析器anchor bolt 地脚螺栓anchor bolt 锚定螺栓anchor 锚，抛锚，锚定anemometer 风速计aneroid barometer无液气压表，无液晴雨angle grinder角锉angle of attack of blade 叶片几何攻角angle of rotor shaft 风轮仰角angle plate角盘annealing 退火annual average wind speed 年平均风速annual average 年平均annual energy production 年发电量annual extreme daily mean of temperature 年最高日平均温度annual maximum 年最高annual variation 年变化annulus环面anode阳极，正极anodization 阳极氧化antenna 天线；触角antifriction减低或防止磨擦之物，润滑剂anvil铁砧apparent sound power level 视在声功率级application drawing操作图，应用图approximate近似，接近，约计arbor 树阴；凉亭；藤架arc control device 灭弧装置arc cutting电弧切割arc gouging 电弧刨削arc welding 电弧焊arc welding 电弧焊arc 弧，弓形，拱，电弧Archimedean screw阿基米德螺线armature circuit 电枢电路armature coil 电枢线圈Armature m.m.f. wave 电枢磁势波armature 电枢articulated接合，链接，有关节的aspect ratio 叶片展弦比assemble集合，聚集，装配assembly 装配assorted files分类排列；相匹配(文件) assume假定，设想，采取，呈现asynchronous generator 异步电机attenuate 衰减attenuation变薄，稀薄化，变细，衰减audit 审计auger打孔钻，螺丝钻auto transformer 自耦变压器automatic station 无人值守电站automatic temperature recorder 温度自动记录器automatic voltage regulator(avr) 自动电压调整器auxiliary circuit 辅助电路auxiliary device 辅助装置auxiliary motor 辅助电动机auxiliary switch辅助接点availability 可利用率（风力发电机组）average noise level 平均噪声average 平均，平均水平，平均数，海损，一般的，通常的aviation light 航空灯awl 锥子axe斧，(经费的)大削减axial pitch 轴向齿距axle 轮轴，车轴Bback saw背锯back-feed反馈backlash反冲，无效行程；间隙，偏移；退balancing equipment 平衡设备ball bearing滚珠轴ball saddle滚珠支撑ball-eye 球头挂环ball-hook 球头挂钩ball-peen hammer 圆头锤band saw 带锯bandwidth 带宽band区；带，波段带子，镶边，波段，队，乐队. 联合，结合bar magnet磁条barometer气压计base material基底材料base 基极basic error 基准误差battery power drill电池钻baud rate波特率baud 波特bayonet 卡口beach海滨；湖滨；河滩bead 珠子，水珠beam compass长臂圆规beam idler gear 惰轮齿beam trammel骨架bearer 支架，托架，支座，载体bearing fittings 轴承配件bearing processing equipment 轴承加工机bearings 轴承bell crank曲柄bellow type 波纹管式belt drive 带传动belting制带的材料，带类，调带装置bend 弯管弯头bending machines 弯曲机bending 挠曲Bessemer converter 酸性转炉，贝塞麦转炉Bessemer酸性转炉钢bevel gear斜角；斜齿轮bevel-edge steel 斜缘薄钢板beveling 磨斜棱，磨斜边biconcave lens两面凹镜biconvex lens两面凸镜bifurcated rivet 开口铆钉；分叉的铆钉bilateral circuit 双向电路bimetallic双金属的bimotored 双马达的bin二进制biphase 双相的bipolar junction transistor (bjt) 双极性晶体管bit 位；比特black body 黑体blade for iron saw 剧刃blade losses 叶片损失blade 叶片blades 刀片blades，saw 锯片blast cleaning皮老虎blast furnace鼓风炉blast 强风bleed 放出(液体，气体等)；漏出，漏入，泄漏，色料扩散bleeder valve 溢流阀blinding plate盲板blind挡板block and tackle滑轮组block diagram 方框图block diagram框图blocking(for wind turbines) 锁定（风力机）blowhole气泡，气孔blowlamp喷灯blowpipe吹风管blowtorch 吹管，喷灯board 底板，板boiler锅炉；煮器；烧水器bolt 螺栓bolts,screws & nuts 螺栓，螺帽及螺丝bolt螺栓，螺钉，支持，维持bonding bar 等电位连接带bonding conductor 等电位连接导体bonding wire 接合线，焊线bone 骨剔除bonnet软帽，汽车发动机罩boost 增压boost-buck 升压去磁bore钻孔，钻boring heads 搪孔头boring machines 镗床both sides welding.双面焊接bottom dead-centre 下死点；下顶点bow-spring compass 弓形片弹簧圆规box spanner inset 插入式套筒扳手box spanner管钳子brace 支柱，带子，振作精神bracket托架，括弧，支架brad 曲头钉bradawl小锥brake fluid 刹车油brake disc 刹车盘brake lining 闸衬片brake mechanism 制动机构brake pad 闸垫brake setting 制动器闭合brake setting 制动器闭合brake shoe 闸轨brake(for wind turbines) 制动器braking mechanism 制动机构braking releasing 制动器释放braking system 制动系统branch connection 分支接续branch of joint连接分支brass黄铜，黄铜制品，brazing铜焊breakaway force 起步阻力breakaway starting current of an a.c. 交流电动机的最初启动电流breakdown torque 极限转矩breakdown 击穿breaker 断路器breast drill 胸压手摇钻breather 呼吸者，喘息者，剧烈的运动bricklayer's hammer 砖匠锤bridges 管式桥bronze 青铜brush wastage 碳刷磨损bubble 磁泡，水泡，气泡buck 补偿bucket桶，一桶的量，铲斗buffing wheel 抛光轮，弹性磨轮bulkhead隔壁，防水壁bulk 大小，体积，大批，大多数，散装bulldozer 推土机Bunsen burner 本生灯burn through 烧蚀burr 芒刺；刺果植物；针球bursting disc 防爆膜bursting 突然破裂，爆发，脉冲bus bar separator 母线间隙垫bus bar support 硬母线固定金？bus bar 母线bus coupler 总线耦合器bus duct 母线槽bus-bar expansion joint 母线伸缩节bush 矮树丛，(机械)衬套bushing轴衬，套管butt weld 对接焊缝butt welding 对接焊byte 字节Ccabinet converter 变频器柜cabinet door 柜门cabinet nacelle transformer 机舱变压器柜cabinet nacelle 机舱机柜cabinet tower 塔基机柜cable armor电缆铠装cable bundle 束，光纤束；捆，卷cable cutter 电缆剪cable fitting电缆配件cable gland 电缆衬垫cable gland 电缆衬垫cable glands 电缆衬垫cable making tools 造线机cable reel 电缆盘cable routing电缆路由选择cable shear 电缆剪cable sheath电缆包皮层cable shoes电缆靴cable tie 电缆带cable tie电缆带cable tray 电缆盘cable trunk 电缆管道cable twist 扭缆cage 笼型calculation sheet计算书calibration标度，刻度，校准caliper测径器，卡钳，弯脚器calorimeter热量计camber 拱形camshaft凸轮轴cam凸轮cancel 取消，删去cantilever伸臂，悬臂；悬臂梁capacitance effect 电容效应capacitance 电容capacitor for voltage protection 保护电容器capacitor 电容器capacity 容量capping ends顶盖末端capstan lathe绞盘车床carbon-filament lamp 碳丝灯泡carburettor 汽化器cardan shaft万向轴carrier 载波cartesian coordinates 笛卡儿坐标系cartridge额盒式磁盘[带](机)；夹头cast-aluminum rotor 铸铝转子castellated coupling 牙嵌式联接casting 铸件，铸造casting, aluminium 铸铝casting, copper 铸铜casting, gray iron 铸灰口铁casting, malleable iron 可锻铸铁casting, other 其他铸造casting, steel 铸钢castle nut城堡螺母cast 投；掷；抛catalyst 催化剂，触媒catastrophic failure(for wind turbines) 严重故障cathode 阴极cathode-ray tube阴极射线管cathodic protection system 阴极保护系统catwalk桥上人行道，狭小通道caulking metal填隙合金[金属](材料) caulking 填…以防漏caution小心ccw 逆时针cement lined piping 水泥衬里cement 水泥，接合剂，接合，用水泥涂，巩固，粘牢center distance 中心距center gear 中心轮center puncher中心冲centralized control 集中控制centre bit中心位centrifugal unit 离心单元centrifugal 离心ceramics 陶瓷；陶瓷技术chain drive 链传动chain making tools 造链机chain vice 链式钳chain wheel 滑轮chain-grate stoker 链条炉排加煤机chamfer machines 倒角机change over switching 换接change over 改变成，对调位channel bases沟渠基底characteristic 特性characteristic curves 特性曲线charge 充电chaser猎人，驱逐舰check against 检查，核对check valve止回阀cheese 干酪，垫砖cheese-head screw 有槽凸圆柱头螺钉chemical corrosion 化学腐蚀chipping 修琢chisel 凿子砍凿chloride 氯化物，漂白粉choke valve 阻气阀choke 窒息，阻气门chopper circuit 斩波电路chord 弦，和音，情绪chrome 铬；铬矿石；氧化铬chronometer 精密计时表chuck 轻拍，抛掷，驱逐，丢弃，用卡盘夹住chucks 夹盘circlip 环形，弹性挡圈circuit branch 支路circuit breaker保护断路器circuit breaker断路开关circuit components 电路元件circuit diagram 电路图circuit diagram 电路图circuit parameters 电路参数circular saw圆锯circular圆形，环；循环circulate 循环；流通circulating循环circumference周线；外围；周围circumferential backlash 圆周侧隙circumferential joint 周圈接缝civil engineer 土木工程师civil works土建工程，建筑工程clamp ammeter钳形表clamp 夹钳clamping/holding systems 夹具/支持系统clamp夹子，夹具，夹钳claw hammer 拔钉锤clearance 排除故障，清除clevis drawbar 牵引环，联结钩clevis joint 拖钩，脚架接头clevis ｕ形夹climate 气候close grain 结晶粒closed circuit 闭合电路clout nail大帽钉club hammer锤子，榔头clutch离合器，联轴器cnc bending presses 电脑数控弯折机cnc boring machines 电脑数控镗床cnc drilling machines 电脑数控钻床cnc edm wire-cutting machines 电脑数控电火花线切削机cnc electric discharge machines 电脑数控电火花机cnc engraving machines 电脑数控雕刻机cnc grinding machines 电脑数控磨床cnc lathes 电脑数控车床cnc machine tool fittings 电脑数控机床配件cnc milling machines 电脑数控铣床cnc shearing machines 电脑数控剪切机cnc toolings cnc 刀杆cnc wire-cutting machines 电脑数控线切削机coarse粗(糙，略)，近似coaxial cable同轴电缆coaxial 共轴的，同轴的cobalt钴(符号为co)，钴类颜料，由钴制的深蓝色code 代码coefficient of torsional rigidity 扭转刚度系数coil 线圈coil spring弹圈coil winding 线圈绕组coincide in phase with 与….同相collar bolt凸缘螺栓collar 凸缘；圈，环，套环，轴；卡圈；安装环collector ring 集电环collector 集电极color identification 彩色识别combination pliers 台钳combination 结合，联合，合并，化合，化合物combustion chamber 燃烧室command 命令commencement 开始commissioning test 投运试验common earthing system 共用接地系统commutation condition 换向状况commutation 换向commutator segment 换向片commutator 换向器commutator-brush combination 换向器-电刷总线complex impedance 复数阻抗complex number 复数complex terrain 复杂地形带compound generator 复励发电机compound 混合物，[化]化合物复合的，混合，配合compounded 复励compressor 压缩物，压缩机，收缩机concave lens 凹面镜concave-convex lens 凸凹镜concrete drill 混凝土钻concrete 混凝土；具体condensation 冷凝condenser 冷凝器；凝结器，电容器conductance 电导conductivity 导电性conductor clamp 卡线钳conductor holder 夹线器conductor 导体conductor 导体conduit box [电]导管分线匣conduit entry 导管引入装置conduit outlet 电线引出口conduit 管道，导管，沟渠，泉水，喷泉cone数、物]锥形物，圆锥体，(松树的)球果，使成锥形conical 圆锥的，圆锥形的conjunction联合，关联，连接词connecting rod连接杆connection 联结connector 接线器considerably 相当地consistency连结，结合，坚固性，浓度，密度，一致性，连贯性console 安慰，藉慰，控制台console 控制台constant chord blade 等截面叶片construction work 施工工程contact 触头contactor 接触器container箱；罐；容器，集装箱，货柜contaminate 污染，弄污continental climate 大陆性气候continuous operation 持续运行contrast使与…对比，使与…对照，和…形成对照，对比，对照，(对照中的) control apparatus 控制电器control cabinet 控制柜control cable 控制电缆操纵索control circuit 控制电路control console 控制台control desk 控制台control device 控制装置control gear 控制设备control panel 控制面板control system(for wind turbine) 控制系统control valve actuator 阀控传动机构control valve 控制阀，control wiring 控制线路control 控制器controller 控制器convection传送；运流；对流convenience receptacle 电源插座converter 变流器convex lens 凸透镜conveying chains 输送链coolers 冷却机cooling 冷却；冷却技术core sand 型芯沙correspond 符合，协调，通信，相当，相应corridor 通路corrosion of metals 金属腐蚀corrosion resistance tests 耐腐试验corrosion 腐蚀corrosion腐蚀，浸蚀cost per kilowatt hour of the electricity generated by wtgs 度电成本cotter pin 开口销counted measured ，metered measured ，metered reading 计量值counter input 脉冲量输入counter weight 重锤countersink bit装定位countersink埋头孔，暗钉眼counting计算coupling bolt 联结，接合，耦合，耦合性，耦合技术coupling capacitor 结合电容coupling 联轴器coupling 联轴器coverage 覆盖；敷层；有效区域crack 裂纹，裂缝cramp 钳位(电路)；压[夹板]；卡子，夹(子)；压[夹]紧crane 吊车crankcase曲柄轴箱crankshaft曲轴；机轴crank不稳定的，摇晃的，曲柄crate 柳条箱crimping tools 卷边工具criterion 标准，判据，准则critical damping 临界阻尼cross mark 十字标记cross slotted screw 十字长孔crosshead 小标题，子题，[机]十字头，丁字头cross-peen hammer 横头锤cross-section 横断面；横切面；截面crosswise 斜地，成十字状地，交叉地crowbar 撬棍；铁棍；起货钩crown wheel 顶圈crucible 坩锅，严酷的考验cubicle 室，箱cumulatively compounded motor 积复励电动机cupola furnace 园顶熔炉current ration 电流定值current 电流curvature function of airfoil 弯度函数customs 进口税，海关cut in wind speed 切入风速cut out wind speed 切出风速cutters 刀具cutter刀具，切割机cutting disk 切割盘cutting opening 切孔cutting 切割cutting-off machines 切断机cw 顺时针cylinder block 缸体cylinder head 缸头cylinder-head gasket 缸头垫片，垫圈；接合垫cylindrical gear 圆柱齿轮cylindrical 圆柱形，圆柱体；柱面Ddaily mean 日平均值dampen使潮湿，使沮丧damper 防振锤damping coefficient 阻尼系数damping ratio 阻尼比damping 阻尼data base 数据库data circuit 数据电路data terminal equipment 数据终端电路date set(for power performance measurement) 数据组（测试功率特性）dc generator 直流发电机dc motor 直流电动机de machine 直流电机deactivate释放；去激励；停用；退出工作；使无效debris碎片，残骸decimal 十进的，小数的，小数decode 译码defective有缺陷的，欠缺的deflect (使)偏斜，(使)偏转deflection偏向；偏斜；转向deformation 变形，形变；畸变，失真degrease脱脂，除油污degree Celsius摄氏度degree of curvature 弯度delta connection 三角形联结demodulator 解调器deploy展开，配置deposit 堆积物，沉淀物，存款，押金，保证金，存放物depression 沮丧，消沉，低气压，低压depressurizes 使减压，使降压depress使沮丧，使消沉，压下，压低depth gauge 深度计design limit 设计极限design pressure 设计压力design situation 设计工况detergent 清洁剂，去垢剂deviation 偏差，偏移dew 露dial gauge量规dial micrometer千分尺diameter and radius 直径和半径diamond cutters 钻石刀具dicing saws 晶圆切割机die casting dies 压铸冲模die casting machines 压铸机dielectric test 介质试验dielectric 电介质，绝缘体dies-progressive 连续冲模diestock 螺丝攻differential gear 差速齿轮differential protection 差动保护differentiation 微分diffuser 漫射体；(扬声器)纸盆；扩散器digger 挖掘者挖掘机digital clock 数字钟digital control 数字控制digital input terminal 数字量输入端子digital output terminal 数字量输出端子digitizing tablet 数字面板dilute 冲淡，变淡，变弱，稀释dimensional inspection 尺寸检验diode module 二极管模块direct axis transient time constant 直轴瞬变时间常数direct axis 直轴direct current machine 直流电机direct current 直流电流direct solar radiation 直接太阳辐射direct voltage 直流电压direct-current 直流directivity(for wtgs) 指向性discharge 卸下，放出，清偿(债务)，履行(义务)，解雇，开(炮)，放(枪)，射(箭)，卸货，流注，放电dismantle拆除，拆卸dismount 拆卸，卸下displacement amplitude 位移幅值displacement current 位移电流display lamp 指示灯disposable tool holder bits 舍弃式刀头disposal 处理，处置，布置，安排，配置，支配disposition notice 处罚通知书dissipation 分散，浪费，损耗，耗散，消耗distance constant 距离常数distance ring间隔环distortion 畸变distributing apparatus 配电电器distribution board配电盘，配电屏distributor发行人，分电盘，配电器diurnal variation 日变化dividers 圆规dog clutch 瓜形(式)离合器，齿式离合器dolly 洋娃娃，移动车，台车，，移动摄影车domed nut 圆顶螺母double clamp 双卡头double phase 两相double-helical gear 人字齿轮doubt 不确定；疑惑dowel 木钉，销子，用暗销接合down conductor 引下线down wind 下风向drag coefficient 阻力系数drain tap 排气阀drain 排水管drain 泄油，排水沟，消耗，排水draw bar 绘图刀drawing board 画图板，制图板drawing machines 拔丝机drawing pin 图钉drawing point 绘图点drift 漂移，偏差drill gauge 钻规drill 训练，钻孔，条播，钻头；锥子；钻孔机；钻床；钻driller 钻孔者，钻孔机drilling machine 钻床drilling machines bench 钻床工作台drilling machines 钻床drilling machines, high-speed 高速钻床drilling machines, multi-spindle 多轴钻床drilling machines, radial 摇臂钻床drilling machines, vertical 立式钻床drills 钻头drip pan油滴盘drive train 传动链driving gear 主动齿轮drop hammer落锤drum brake鼓状刹车drum鼓，鼓声dry type transformer 干式变压器dryness干，干燥duplex transmission 双工传输durability 耐久性duration宽度，持续时间dust protected 防尘dust 灰尘，尘土，尘埃duty ratio 负载比dye penetrant examination 染料渗透试验法dynamic coupling 齿啮式联接dynamic response 动态响应dynamic-state operation 动态运行dynamo 发电机dynamometer 测力计，功率计Ee.m.f = electromotive fore 电动势earth conductor 接地线earth electrode 接地体earth termination system 接地装置earth;ground 地earthed circuit 接地电路earthing reference points 接地基准点earthing switch 接地开关eddy current 涡流effective values 有效值effects of saturation 饱和效应efficiency of wtgs 机组效率efficiency 效率elastic coupling 弹性联接elbow 弯管接头electric arc电弧electric charge 电荷electric circuit 电路electric coupling 耦合器electric current 电流electric discharge machines(edm) 电火花机electric energy transducer 电能转换器electric energy 电能electric heat tracing.电伴随加热electric machine 电机electric power tools 电动刀具electric shock 触电；电击electric wire and cable 电线电缆electric 电的electrical contact 电触头electrical device 电气设备electrical device 电气元件electrical discharge 放电electrical endurance 电气寿命electrical material电气材料electrical panel 配电板，配电盘electrical rotating machine 旋转电机electricity 电electrode 电焊条electrode 电极electrode 电极电焊条electrolysis 电解，电蚀electrolyte电解，电解液electromagnetic braking system 电磁制动系electromagnetic induction 电磁感应electromagnetic torque 电磁转矩electroplating 电镀，电镀术electrostatics 静电学eliminate消除，删去，排除；切断embedded pc 嵌入式pcemergency braking system 紧急制动系统emergency shutdown 紧急关机emergency stop push button 紧急停车按钮emergency-stop 紧急停止emery cloth砂布，金刚砂布emery wheel 金刚砂旋转磨石，砂轮emery 金刚砂，刚玉砂emitter 发射管放射器发射极encode 编码end ring 端环endplate终板endurance test 耐久性试验endwise 末端朝前或向上的，向前的energizing 使活跃，给予精力，加强，给与…电压energy converter 电能转换器engagement mesh 啮合engraving machines 雕刻机engraving machines, laser 激光雕刻机environment condition 环境条件environment 环境epicyclical gear计数齿epoch angle 初相角epoxy 环氧树脂epoxy-glued环氧胶equilateral triangle 等边三角形equipment failure information 设备故障信息equipotential bonding 等电位连接equivalent t circuit t型等值电路erection 架设erection直立，竖起，建筑物error codes 故障代码error detector 误差检测器error signal 误差信号etching machines 蚀刻机ethercat extension扩展端子event information 事件信息examination试验excitation response 励磁excitation response 励磁响应excitation system 励磁系统excitation励磁excited by 励磁exciter 励磁机exciting voltage 励磁电压exfoliation剥落exhaust pipe 排气管exhaust valve排气阀expanded metal膨胀金属expander扩展器，扩展电路，扩大器expansion bolt 伸缩栓，扩开螺栓expansion bolt伸缩栓，扩开螺栓expansion bolt自攻螺丝expansion joint 伸缩接头expansion joint 伸缩接头explanatory quad填充铅块extension tube伸缩管external armature circuit 电枢外电路external calipers 外卡钳external characteristic 外特性external conditions(for wind turbines) 外部条件（风力机）external conditions(for wtgs) 外部条件external gear 外齿轮external lightning protection system 外部放雷系统external power supply 外部动力源extern外(面)的，外来的extrapolated power curve 外推功率曲线extreme 极端extreme maximum 极端最高extreme wind speed 极端风速extrusion 挤压，挤压成形eye bolt 吊耳eye screw螺丝眼Ffabrication drawing 制造图纸，制作图fabrication tolerance 制造容差fabrication 加工，制造fabrication 制造；生产；结构fabrication.制造face width 齿宽faceplate面板，花盘facilitate使容易，使便利，推动，帮助，使容易，促进fag bolt，疲劳螺栓fail safe 安全性failure 失效fake假货，欺骗，伪造，赝造，捏造，假造，仿造fan belt风扇皮带fan heater 风扇加热器fault earthing 故障接地fault 故障feather position 顺桨位置feathering 顺浆feedback component 反馈元件feedback loop 反馈回路feedback signal 反馈信号feedback system 反馈系统feeder 馈电线feeler gauge触规felling axe外轮轴ferritic 铁素体的fetch 接来，取来，带来，售得，引出，吸引，到达，演绎出fidelity 保真度field coils 励磁线圈field current 励磁电流field data 现场数据field effect transistor (fet) 场效应管field fabricated 工地制造的，现场装配的field installation 现场安装field instrument 携带式仪表field reliability test 现场可靠性试验field test with turbine 外联机试验field winding 磁场绕组励磁绕组filament灯丝；细丝filler metal 焊料，焊丝filler rod焊条fillet weld 角焊，填角焊film density 影片密度film viewer底片观察用光源filter 过滤器finishing machines 修整机fire barriers防火间隔fire extinguisher灭火器firebrick 耐火砖fireman's axe消防斧firmer chisel 凿子fixing 固定fixture 夹具flange connection.凸缘联接flange coupling凸缘联轴器flange gasket 法兰垫片flange joint 凸缘接头flange 边缘，轮缘，凸缘，法兰flange 凸缘flanged nut凸缘螺母flanged union凸缘连接flank侧面，军队侧翼，侧腹flash plate闪熔镀层flash welding 闪光焊flashlight手电筒，闪光灯flashover 闪络flashpoint闪点flat nut平螺母flat 平坦的，扁平的，单调的，倒下的，浅的flat-head rivet平头铆钉flaw裂缝，缺陷，疵瑕flexible conduit软管flexible gear 柔性齿轮flexible rolling bearing 柔性滚动轴承flexural rigidity 抗挠刚度flexure 弯曲，挠曲flex弯曲(四肢)，伸缩，折曲flicker coefficient for continuous operation 持续运行的闪变系数flicker step factor 闪变阶跃系数flicker 闪变float chamber浮子floating 漂浮的，浮动的，移动的，流动的，不固定的flow charts 流程图flow distortion 气流畸变flow instrument 流量计flow instrument流量计flow sheet 流程图flue烟洞，烟道，暖气管，蓬松的东西flushing 冲洗，填缝flush刷新flutter 颤振flux linkage 磁链flux 磁通，通量；焊剂；流动，熔化，流出flux 焊剂fog 雾foot pump脚泵forge炼炉；熔炉forging dies 锻模forging，aluminium 锻铝forging，cold 冷锻forging，copper 铜锻forging，other 其他锻造forging，steel 钢锻fork 派生(指令)，分叉(指令)，分支fork-lift truck 叉架式运货车，铲车formation 构造，结构；形成，建立；形式forming 印版form-wound 模绕forward transfer function 正向传递函数foundation earth electrode 基础接地体foundation 基础，根本，建立，创立，地基foundry equipment 铸造设备foundry铸造，翻砂，铸工厂，玻璃厂，铸造厂four-jaw chuck 四爪卡盘four-stroke 四冲程frame 帧，画面；框架机架，架，机柜free stand tower 独立式塔架free stream wind speed 自由流风速freezing rain 冻雨frequency converter 变频器frequency of wind speed 风速频率frequency shift keying(fsk) 移频键控frequency 频率frequency 频率fret-saw线剧friction grip摩擦盘friction 摩擦，摩擦力frictional摩擦的，摩擦力的front end processor 前置机frost霜，霜冻，严寒，结霜full load 满载full load 满载full-load torque 满载转矩funnel 漏斗，烟窗furnace炉子，熔炉furnish 供应，提供，装备，布置fuse 溶断器fusion 熔融Ggage glass 液位玻璃管gain 增益gain 增益gale强风，大风galvanizing 通电流于，电镀gang saw 直锯gas burner 煤气灶，煤气火焰gas cutting 气割gas main 煤气总管gas mask防毒面具gas pedal气体，煤气，毒气，汽油，瓦斯gas turbine 燃气涡轮gas well 天然气井gas works煤气厂gaskets垫片，垫圈；接合垫gasket垫片，垫圈；接合垫gasometer 煤气厂，气量计gate pole门极gate valve门阀gauge board样板，模板规准尺gauge board仪表板gauge标准尺，规格，量规，量表，测量gavel 槌gear bearing de 齿轮轴承驱动端gear bearing nde 齿轮轴承非驱动端gear box ratio 齿轮箱变比gear cutting machines 齿轮切削机gear fan 齿轮箱冷却风扇gear lever 变速杆gear motor 齿轮马达gear oil pump hs 齿轮油泵高速gear oil pump ls 齿轮油泵低速gear pair with parallel axes 平行轴齿轮副gear pair 齿轮副gear pump 齿轮泵gear train齿轮系gear water pump 齿轮水泵gear wheel齿轮gear 齿轮gears with addendum modification 变位齿轮gears 齿轮geiger counter盖格计数器gel-coated胶衣generating 发电generator fan external 发电机外部风扇generator fan internal 发电机内部风扇generator voltage 发电机电压generator 发电机geometric chord of airfoil 几何弦长geometrical position 几何位置gimbals 平衡环，平衡架gimlet手钻；螺丝锥girder bridgegirder 梁，钢桁的支架girth weld环形焊缝gland腺，密封管glass cutter玻璃刀glaze釉料，釉面，光滑面，上釉，上光globe valve球形阀gloss paint光滑涂料glossy 平滑的，有光泽的gloss注释；注解；评注，光泽的表面，光彩，欺人的表面，假象，glove手套glue胶，胶水，胶合，粘贴，粘合goggle 眼睛睁视，(复数)风镜，护目镜goggles 护目镜gold leaf金叶goons细打包麻布gouge弧口凿，半圆凿gouging 刨削槽governor 调节器；控制器grab 抢夺，攫取，夺取grader 分类机，分级机grading ring 均压环grain 颗粒，晶粒，粒度；纹理graph 图表，曲线图gravity casting machines 重力铸造机grazing angle 掠射角grease gun注油枪；滑脂枪grease nipple油管grease油膏；润滑油greenhouse effect 温室效应grid 电网grind off 磨掉grinder bench 磨床工作台grinder 磨床grinders，thread 螺纹磨床grinders，tools & cutters 工具磨床grinders，ultrasonic 超声波打磨机grinding disk 磨擦盘grinding machines 磨床grinding machines，centerless 无心磨床grinding machines，cylindrical 外圆磨床grinding machines，universal 万能磨床grinding machine磨床grinding tools 磨削工具grinding wheel 砂轮grinding wheels 磨轮grinding磨的，磨擦的，碾的groove凹槽，惯例，最佳状态grounding conductor 接地导体grout 薄泥浆，水泥浆grouting 灌浆grouting给…灌灰浆，给…涂薄胶泥grub screw自攻螺丝guide bars导向棍guide block导向块guide ring导向绳guide wire 尺度[定距]索，准绳guiding shaft导向轴guillotine闸刀，处斩刑，切(纸) gumming树胶分泌gusset plate角撑板，加固板gust influence 阵风影响gust 阵风guy clip 线卡子guyed tower 拉索式塔架gyroscope 陀螺仪，回旋装置，回转仪，纵舵调整器Hhacksaw可锯金属的弓形锯，钢锯hail 冰雹hairspring细弹簧，游丝half duplex transmission 半双工传输half shaft半轴half-round file半圆锉halfway中途的，部分的，不彻底的，半路地，在中途，在半途hand tools 手工具handling 处理(技术，方法)hanger 吊架hanger吊架hanging顶端对齐，悬挂hard hat 安全帽hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组hardener 固化剂，硬化剂harder硬的，坚固的，(问题，工作等)困难的，艰苦的，猛烈的，确实的hardware platform 硬件平台hardware 硬件harmonic 谐波的harmonics 谐波harness导线，装备；利用harrow 耙hatch，舱口，舱口盖，开口，孵，孵出，策划，图谋hatchet 短柄斧hazard 冒险(性)；相关危险；事故，故障head screw 主轴螺杆headstock主轴箱heat preserving furnaces 保温炉heater 加热器heating appliance 电热器heating boxes加热室heating treatment funaces 熔热处理炉helical gear; single-helical gear 斜齿圆柱齿轮helical gearing 螺旋齿helix 螺旋，螺旋状物hemp 大麻，纤维hereafter 今后，从此以后Herringbone gear 人字（齿）轮，双螺旋齿轮hexagon screw die 六角板牙，六角螺丝钢板hexagon spanner六方hexagonal nut六角螺母high frequency generator 高频发电机high voltage高压high-gain 高增益high-performance 高性能的hightensile 高强度high-tension cable高压电缆hissing发嘶嘶声，蔑视hob滚刀，铁架hoe 锄头，用锄耕地，锄hoist升起；吊起；推起，起重机，(台、架等)支持物，固定器hollow空的，中空的honing machines 搪磨机hook bolt吊耳hook spanner 钩，弯脚扳手hook 挂钩hook's joint 钩结合，钩（连）接hopper 单足跳者horizontal axis wind turbine 水平轴风力机horizontal line 水平线horizontal地平线的，水平的horsepower 马力horseshoe magnet 马蹄形磁铁horseshoe magnet马蹄形磁铁hose clip管夹hose 软管，胶皮管，蛇管hot-dip热沾hottest 热的，热烈的housing住房，房屋，护盖，框架hovercraft 水翼船hub height 轮毂高度hub rigidity轮毂刚度hub 轮毂hubcap 轮毂罩hull外壳，船体humidity湿气，潮湿，湿度hydraulic block液压块hydraulic braking system 液压制动系统hydraulic components 液压元件hydraulic cylinder 液压缸hydraulic filter 液压过滤器hydraulic fluid 液压油hydraulic motor 液压马达hydraulic power tools 液压工具hydraulic power units 液压动力元件hydraulic pump 液压泵hydraulic ram液压活塞hydraulic rotary cylinders 液压回转缸hydraulic system 液压系统hydraulic水压的；液压的hydropower station 水电站hydrostatic pressure test静水压试验hydrostatic test 流体静力学试验，水压试验hygrographs 自动湿度记录计hygrometer湿度计hysteresis 滞后作用，[物]磁滞现象Iice sensor 结冰传感器ideal source 理想电源identification mark 识别标志idler pulley惰轮，空转轮，导轮idling(for wind turbines) 空转（风力机）imaginary part 虚部impedance voltage 阻抗电压impedance 阻抗impedance 阻抗impeller 推进者，叶轮imperfection 缺陷impinge 撞击，冲击imprint 印记imprison监禁，关押impulse load tests 冲击动荷试验impulse推动，刺激，冲动，推动力，脉冲impurity杂质，混杂物，不洁，不纯incident 入射的inclusion 杂质incremental encoder 增量式编码器incremental outputs 增量式输出indoor climate 室内气候induced current 感生电流inductance 电感induction coil电感线圈induction generator 感应电机induction generator 感应发电机induction machine 感应电机induction machine 感应电机induction machine 感应式电机induction motor 感应电动机inductive component 感性（无功）分量inductive 诱导的，感应的inductor 电感器inertia switch惯性开关inertial sub range 湍流惯性负区infinite voltage gain 无穷大电压增益inflammable易燃的，易怒的influence by the tower shadow 塔影响效应influence by the wind shear 风切变影响information 信息ingot 条，块，锭initial 最初的，词首的，初始的initialize 初始化initials 缩写injector 注射器injure 损害，伤害inlet valve入口阀inlet 进口，入口inner 内部的，里面的，内心的，内部inoperative不起作用的；无效的input 输入input power 输入功率input shaft 输入轴inrush current 涌流inspection earthing 检修接地inspection 审查，检查instance 例图；事[实，范]例，样品，实例，建议，要求，情况，场合instantaneous electric power 瞬时电功率instantaneous measured 瞬时侧值instantaneous mechanical power 瞬时机械功率instantaneous power 瞬时功率instantaneous value 瞬时值instantaneous瞬间的，即刻的，即时的，瞬时，立即instrument air仪表气源instrument rack 计测器支架instrument rack 计测器支架，计测器框架insufficient不充足的，不适合的，不能胜任的insulant 绝缘物insulated sleeve绝缘套管insulating boots 绝缘靴insulating bushing 绝缘套管insulating glove 绝缘手套insulation level 绝缘比insulation resistance 绝缘电阻insulation 绝缘insulation 绝缘insulator 绝缘子integrated coupling 固定联接integrated，total integrated value 累计值integration 积分下限intensifying screen 增光屏，光增强屏interconnection(for wtgs) 互连（风力发电机组）interface 接口。

风力发电机组术语(中英文对照)

风力发电机组术语(中英文对照),国家标准1范围本标准规定了风力发电机组常用基本术语和定义。

本标准适用于风力发电机组。

其它标准中的术语部分也应参照使用。

2定义本标准采用下列定义。

2.1风力机和风力发电机组2.1.1风力机wind turbine将风的动能转换为另一种形式能的旋转机械。

2.1.2风力发电机组wind turbine generator system;WTGS(abbreviation)将风的动能转换为电能的系统。

2.1.3风电场wind power station；wind farm由一批风力发电机组或风力发电机组群组成的电站。

2.1.4水平轴风力机horizontal axis wind turbine风轮轴基本上平行于风向的风力机。

2.1.5垂直轴风力机vertical axis wind turbine风轮轴垂直的风力机。

2.1.6轮毂（风力机）hub（for wind turbines）将叶片或叶片组固定到转轴上的装置。

2.1.7机舱nacelle设在水平轴风力机顶部包容电机、传动系统和其它装置的部件。

2.1.8支撑结构（风力机）support structure（for wind turbines）由塔架和基础组成的风力机部分。

2.1.9关机（风力机）shutdown（for wind turbines）从发电到静止或空转之间的风力机过渡状态。

2.1.10正常关机（风力机）normal shutdown（for wind turbines）全过程都是在控制系统控制下进行的关机。

2.1.11紧急关机（风力机）emergency shutdown（for wind turbines）保护装置系统触发或人工干预下，使风力机迅速关机。

2.1.12空转（风力机）idling（for wind turbines）风力机缓慢旋转但不发电的状态。

2.1.13锁定（风力机）blocking（for wind turbines）利用机械销或其它装置，而不是通常的机械制动盘，防止风轮轴或偏航机构运动。

风力发电术语中英文对照

风力发电机用专业英语中文对照(一)风力机wind turbine风电场wind power station wind farm风力发电机组wind turbine generator system WTGS 水平轴风力机horizontal axis wind turbine垂直轴风力机vertical axis wind turbine轮毂（风力机）hub (for wind turbine)机舱nacelle支撑结构support structure for wind turbine关机shutdown for wind turbine正常关机normal shutdown for wind turbine紧急关机emergency shutdown for wind turbine空转idling锁定blocking停机parking静止standstill制动器brake停机制动parking brake风轮转速rotor speed控制系统control system保护系统protection system偏航yawing设计和安全参数design situation设计工况design situation载荷状况load case外部条件external conditions设计极限design limits极限状态limit state使用极限状态serviceability limit states极限限制状态ultimate limit state最大极限状态ultimate limit state安全寿命safe life严重故障 catastrophic failure潜伏故障latent fault dormant failure风特性wind characteristic风速wind speed风矢量wind velocity旋转采样风矢量rotationally sampled wind velocity 额定风速rated wind speed切入风速cut-in speed切出风速cut-out speed年平均annual average年平均风速annual average wind speed平均风速mean wind speed极端风速extreme wind speed安全风速survival wind speed参考风速reference wind speed风速分布wind speed distribution瑞利分布RayLeigh distribution威布尔分布Weibull distribution风切变wind shear风廓线风切变律wind profile wind shear law 风切变指数wind shear exponent对数风切变律logarithmic wind shear law风切变幂律power law for wind shear下风向down wind上风向up wind阵风gust粗糙长度roughness length湍流强度turbulence intensity湍流尺度参数turbulence scale parameter 湍流惯性负区inertial sub-range风场wind site测量参数measurement parameters测量位置measurement seat最大风速maximum wind speed风功率密度wind power density风能密度wind energy density日变化diurnal variation年变化annual variation轮毂高度hub height风能wind energy标准大气状态standard atmospheric state 风切变影响influence by the wind shear阵风影响gust influence风速频率frequency of wind speed环境environment工作环境operational environment气候climate海洋性气候ocean climate大陆性气候continental climate露天气候open-air climate室内气候indoor climate极端extreme日平均值daily mean极端最高extreme maximum年最高annual maximum年最高日平均温度annual extreme daily mean of temperature 月平均温度mean monthly temperature空气湿度air humidity绝对湿度absolute humidity相对湿度relative humidity降水precipitation雨rain冻雨freezing rain霜淞rime雨淞glaze冰雹hail露dew雾fog盐雾salt fog雷暴thunderstorm雪载snow load标准大气压standard air pressure平均海平面mean sea level海拔altitude辐射通量radiant flux太阳辐射solar radiation直接太阳辐射direct solar radiation天空辐射sky radiation太阳常数solar constant太阳光谱solar spectrum黑体black body白体white body温室效应greenhouse effect环境温度ambient temperature表面温度surface temperature互联interconnection输出功率output power额定功率rated power最大功率maximum power电网连接点network connection point电力汇集系统power collection system风场电器设备site electrical facilities功率特性power performance静电功率输出net electric power output功率系数power performance自由流风速free stream wind speed扫掠面积swept area轮毂高度hub height测量功率曲线measurement power curve外推功率曲线extrapolated power curve年发电量annual energy production可利用率availability数据组功率特性测试data set for power performance measurement 精度accuracy测量误差uncertainty in measurement分组方法method of bins测量周期measurement period测量扇区measurement sector日变化diurnal variations浆距角pitch angle距离常数distance constant试验场地test site气流畸变flow distortion障碍物obstacles复杂地形带complex terrain风障wind break声压级sound pressure level声级weighted sound pressure level; sound level视在声功率级apparent sound power level指向性directivity音值tonality声的基准面风速acoustic reference wind speed标准风速standardized wind speed基准高度reference height基准粗糙长度reference roughness length基准距离reference distance掠射角grazing angle风轮风轮wind rotor风轮直径rotor diameter风轮扫掠面积rotor swept area风轮仰角tilt angle of rotor shaft风轮偏航角yawing angle of rotor shaft风轮额定转速rated turning speed of rotor风轮最高转速maximum turning speed of rotor风轮尾流rotor wake尾流损失wa传动比transmission ratio齿轮gear齿轮副gear pair平行轴齿轮副gear pair with parallel axes齿轮系train of gears行星齿轮系planetary gear train小齿轮pinion大齿轮wheel , gear主动齿轮driving, gear从动齿轮driven gear行星齿轮planet gear行星架planet carrier太阳轮sun gear内齿圈ring gear外齿轮external gear内齿轮internal内齿轮副internal gear pair增速齿轮副speed increasing gear增速齿轮系speed increasing gear train中心距center distance增速比speed increasing ratio齿面tooth flank工作齿面working flank非工作齿面non-working flank模数module齿数number of teeth啮合干涉meshing interference齿廓修行profile modification , profile correction 啮合engagement, mesh齿轮的变位addendum modification on gears 变位齿轮gears with addendum modification圆柱齿轮cylindrical gear直齿圆柱齿轮spur gear斜齿圆柱齿轮helical gear single-helical gear 节点pitch point节圆pitch circle齿顶圆tip circle齿根圆root circle直径和半径diameter and radius齿宽face width齿厚tooth thickness压力角pressure angle圆周侧隙circumferential backlash蜗杆worm蜗轮worm wheel联轴器coupling刚性联轴器rigid coupling万向联轴器 universal coupling安全联轴器security coupling齿tooth齿槽tooth space斜齿轮helical gear人字齿轮double-helical gear齿距pitch法向齿距normal pitch轴向齿距axial pitch齿高tooth depth输入角input shaft输出角output shaft柱销pin柱销套roller行星齿轮传动机构planetary gear drive mechanism 中心轮center gear单级行星齿轮系single planetary gear train柔性齿轮flexible gear刚性齿轮rigidity gear柔性滚动轴承flexible rolling bearing输出联接output coupling刚度rigidity扭转刚度torsional rigidity弯曲刚度flexural rigidity扭转刚度系数coefficient of torsional起动力矩starting torque传动误差transmission error传动精度transmission accuracy固有频率natural frequency弹性联接elastic coupling刚性联接rigid coupling滑块联接Oldham coupling固定联接integrated coupling齿啮式联接dynamic coupling花键式联接splined coupling牙嵌式联接castellated coupling径向销联接radial pin coupling周期振动periodic vibration随机振动random vibration峰值peak value临界阻尼critical damping阻尼系数damping coefficient阻尼比damping ratio减震器vibration isolator振动频率vibration frequency幅值amplitude位移幅值displacement amplitude速度幅值velocity amplitude加速度幅值acceleration amplitude控制与监控系统远程监视telemonitoring协议protocol实时real time单向传输simplex transmission半双工传输half-duplex transmission双工传输duplex transmission前置机front end processor运输终端remote terminal unit调制解调器modulator-demodulator数据终端设备data terminal equipment接口interface数据电路data circuit信息information状态信息state information分接头位置信息tap position information监视信息monitored information设备故障信息equipment failure information告警alarm返回信息return information设定值set point value累积值integrated total integrated value瞬时测值instantaneous measured计量值counted measured metered measured metered reading 确认acknowledgement信号signal模拟信号analog signal命令command字节byte位bit地址address波特baud编码encode译码decode代码code集中控制centralized control可编程序控制programmable control微机程控minicomputer program模拟控制analogue control数字控制digital control强电控制 strong current control弱电控制weak current control单元控制unit control就地控制local control联锁装置interlocker模拟盘analogue board配电盘switch board控制台control desk紧急停车按钮emergency stop push-button 限位开关limit switch限速开关limit speed switch有载指示器on-load indicator屏幕显示screen display指示灯display lamp起动信号starting signal公共供电点point of common coupling闪变flicker数据库data base硬件hardware硬件平台hardware platform层layer level class模型model响应时间response time软件software软件平台software platform系统软件system software自由脱扣trip-free基准误差basic error一对一控制方式one-to-one control mode 一次电流primary current一次电压primary voltage二次电流secondary current二次电压secondary voltage低压电器low voltage apparatus额定工作电压rated operational voltage额定工作电流rated operational current运行管理operation management安全方案safety concept外部条件external conditions失效failure故障fault控制柜control cabinet冗余技术redundancy正常关机normal shutdown失效-安全fail-safe排除故障clearance空转idli负载load加载to load充电to charge放电to discharge有载运行on-load operation空载运行no-load operation开路运行open-circuit operation 短路运行short-circuit operation 满载full load效率efficiency损耗loss过电压over-voltage过电流over-current欠电压under-voltage特性characteristic绝缘物insulant隔离to isolate绝缘insulation绝缘电阻insulation resistance 品质因数 quality factor泄漏电流leakage current闪烙flashover短路short circuit噪声noise极限值limiting value额定值rated value额定 rating环境条件environment condition 使用条件service condition工况operating condition额定工况rated condition负载比duty ratio绝缘比insulation ratio介质试验dielectric test常规试验routine test抽样试验sampling test验收试验acceptance test投运试验commissioning test维护试验maintenance test加速accelerating特性曲线characteristic额定电压rated voltage额定电流rated current额定频率rated frequency温升temperature rise温度系数temperature coefficient端电压terminal voltage短路电流short circuit current可靠性reliability有效性availability耐久性durability维修maintenance维护preventive maintenance工作时间operating time待命时间standby time修复时间repair time寿命life使用寿命useful life平均寿命 mean life耐久性试验endurance test寿命试验life test可靠性测定试验reliability determination test 现场可靠性试验field reliability test加速试验accelerated test安全性fail safe应力stress强度strength试验数据test data现场数据field data电触头electrical contact主触头main contact击穿breakdown耐电压proof voltage放电electrical discharge透气性air permeability电线电缆 electric wire and cable电力电缆power cable通信电缆telecommunication cable油浸式变压器oil-immersed type transformer 干式变压器dry-type transformer自耦变压器auto-transformer有载调压变压器transformer fitted with OLTC 空载电流non-load current阻抗电压impedance voltage电抗电压reactance voltage电阻电压resistance voltage分接tapping配电电器distributing apparatus控制电器control apparatus开关switch熔断器fuse断路器circuit breaker控制器controller接触器contactor机械寿命mechanical endurance电气寿命electrical endurance旋转电机electrical rotating machine直流电机direct current machine交流电机alternating current machine同步电机synchronous machine异步电机asynchronous machine感应电机induction machine励磁机exciter饱和特性saturation characteristic开路特性open-circuit characteristic负载特性load characteristic短路特性short-circuit characteristic额定转矩rated load torque规定的最初起动转矩specifies breakaway torque交流电动机的最初起动电流breakaway starting current if an a.c. 同步转速synchronous speed转差率slip短路比short-circuit ratio同步系数synchronous coefficient空载no-load系统system触电；电击electric block正常状态normal condition接触电压touch voltage跨步电压step voltage对地电压voltage to earth触电电流shock current残余电流residual current安全阻抗safety impedance安全距离safety distance安全标志safety marking安全色safety color中性点有效接地系统system with effectively earthed neutral检修接地inspection earthing工作接地working earthing保护接地protective earthing重复接地iterative earth故障接地fault earthing过电压保护over-voltage protection过电流保护over-current protection断相保护open-phase protection防尘dust-protected防溅protected against splashing防滴protected against dropping water防浸水protected against the effects of immersion 过电流保护装置over-current protective device保护继电器protective relay接地开关earthing switch漏电断路器residual current circuit-breaker灭弧装置arc-control device安全隔离变压器safety isolating transformer避雷器surge attester ; lightning arrester保护电容器 capacitor for voltage protection安全开关safety switch限流电路 limited current circuit振动vibration腐蚀 corrosion点腐蚀 spot corrosion金属腐蚀corrosion of metals化学腐蚀chemical corrosion贮存 storage贮存条件storage condition运输条件transportation condition空载最大加速度maximum bare table acceletation 电力金具悬垂线夹suspension clamp耐张线夹strain clamp挂环link挂板clevis球头挂环ball-eye球头挂钩ball-hookU型挂环shackleU型挂钩U-bolt联板yoke plate牵引板towing plate挂钩hook吊架hanger调整板adjusting plate花篮螺栓turn buckle 接续管splicing sleeve 补修管repair sleeve调线线夹jumper clamp 防振锤damper均压环grading ring屏蔽环shielding ring。

风力发电机名词术语汉英对照

风力发电机名词术语汉英对照(1)2008年06月08日星期日14:21风力机wind turbine风电场wind power station wind farm 风力发电机组wind turbine generator system WTGS 水平轴风力机horizontal axis wind turbine垂直轴风力机vertical axis wind turbine轮毂（风力机）hub (for wind turbine)机舱nacelle支撑结构support structure for wind turbine关机shutdown for wind turbine正常关机normal shutdown for wind turbine紧急关机emergency shutdown for wind turbine空转idling锁定blocking停机parking静止standstill制动器brake停机制动parking brake风轮转速rotor speed控制系统control system保护系统protection system偏航yawing设计和安全参数design situation设计工况design situation载荷状况load case外部条件external conditions设计极限design limits极限状态limit state使用极限状态serviceability limit states极限限制状态ultimate limit state最大极限状态ultimate limit state安全寿命safe life严重故障catastrophic failure潜伏故障latent fault dormant failure风特性风速wind speed风矢量wind velocity旋转采样风矢量rotationally sampled wind velocity 额定风速rated wind speed切入风速cut-in speed切出风速cut-out speed年平均annual average年平均风速annual average wind speed平均风速mean wind speed极端风速extreme wind speed安全风速survival wind speed参考风速reference wind speed风速分布wind speed distribution瑞利分布RayLeigh distribution威布尔分布Weibull distribution风切变wind shear风廓线风切变律wind profile wind shear law 风切变指数wind shear exponent对数风切变律logarithmic wind shear law风切变幂律power law for wind shear下风向down wind上风向up wind阵风gust粗糙长度roughness length湍流强度turbulence intensity湍流尺度参数turbulence scale parameter湍流惯性负区inertial sub-range风场wind site测量参数measurement parameters测量位置measurement seat最大风速maximum wind speed风功率密度wind power density风能密度wind energy density日变化diurnal variation年变化annual variation轮毂高度hub height风能wind energy标准大气状态standard atmospheric state风切变影响influence by the wind shear阵风影响gust influence风速频率frequency of wind speed环境environment工作环境operational environment气候climate海洋性气候ocean climate大陆性气候continental climate露天气候open-air climate室内气候indoor climate极端extreme日平均值daily mean极端最高extreme maximum年最高annual maximum年最高日平均温度annual extreme daily mean of temperature 月平均温度mean monthly temperatureabrasive研磨料abrasive disc磨料盘accumulator储压罐acetone丙酮activation活动，赋活，激活，活化，激励，启用acute angle锐角adhesive带粘性的,胶粘,粘合剂adjustable spanner活动扳手admixture混合,混合物adversely逆地,反对地adze扁斧aerial航空的,生活在空气中的,空气的,高耸的,天线aerosol浮质,气溶胶,气雾剂,烟雾剂aggregate合计,总计,集合体aggressively侵略地,攻势地air inlet通风口air-cushion vehicle气垫船air gap气隙align对准，校直，定位；调,排列,使结盟,使成一行alkali-sensitive碱性感测allen key六方allen wrench六方扳手alloy合金alteration变更,改造alternator交替符；交流发电机ammeter安培计，电流表anaerobic没有空气而能生活的,厌氧性的anchor锚,抛锚,锚定aneroid barometer无液气压表,无液晴雨angle grinder角锉angle plate角盘annealing退火annulus环面anode阳极,正极anodization阳极氧化antenna天线；触角antifriction减低或防止磨擦之物,润滑剂anvil铁砧approximate近似,接近,约计adjarbor树阴；凉亭；藤架〈机〉柄轴；心轴arc弧,弓形,拱,电弧arc welding电弧焊archimedean screw阿基米德螺线arrmature电枢articulated接合,链接,有关节的assemble集合,聚集,装配assorted files分类排列；相匹配(文件)assume假定,设想,采取,呈现attenuation变薄,稀薄化,变细,衰减auger打孔钻，螺丝钻averagen.平均,平均水平,平均数,海损,一般的,通常的awln锥子axe斧, (经费的)大削减axle.轮轴,车轴Bback saw背锯backlash反冲，无效行程；间隙，偏移；退ball bearing滚珠轴ball saddle滚珠支撑ball-peen hammerband区；带，波段带子,镶边,波段,队,乐队.联合,结合bandsaw用带锯锯bar magnet磁条barometer气压计；晴雨表battery power drill电池钻beach海滨；湖滨；河滩bead珠子,水珠beam compass长臂圆规beam trammel骨架bearer支架，托架，支座，载体bell crank曲柄belting制带的材料,带类,调带装置bessemer酸性转炉钢bessemer converter .酸性转炉,贝塞麦转炉bevel gear斜角；斜齿轮bevel-edge shisel斜缘薄钢板biconcave lens两面凹镜biconvex lens两面凸镜bifurcated rivetbimetallic双金属的bin二进制；双态bit位,比特blade for iron saw剧刃blast强风，过载blast furnace鼓风炉blast cleaning皮老虎bleed放出(液体，气体等)；漏出，漏入，泄漏，色料扩散bleeder valve溢流阀block and tackle滑轮组blowlamp喷灯blowpipe吹风管blowtorch吹管,喷灯board底板，板boiler锅炉；煮器；烧水器bolt螺栓，螺钉，支持，维持bone骨剔除bonnet软帽,汽车发动机罩bore钻孔,钻bottom dead-centrebow-spring compassbox spanner管钳子box spanner insetbrac支柱,带子,振作精神bracket托架,括弧,支架brad曲头钉bradawl小锥Brakebrake lining闸,刹车的衬里,内层,衬套brake shoe闸轨branch of joint连接分支brass黄铜,黄铜制品,brazing铜焊breast drillbreather呼吸者,喘息者,剧烈的运动bricklayer’s hammerbubble磁泡，水泡，气泡bucket桶,一桶的量,铲斗Buffing wheelbulk大小,体积,大批,大多数,散装bulkhead隔壁,防水壁bulldozer推土机bunsen burner本生灯burr芒刺；刺果植物；针球burstn.突然破裂,爆发,脉冲bursting discbush矮树丛, (机械)衬套bushing轴衬,套管Ccabinet screw drivercable bundle束，光纤束；捆，卷cable reel电缆盘cable shear电缆剪cable shoes电缆靴cable tie电缆带calibration标度,刻度,校准caliper测径器,卡钳,弯脚器cam凸轮camber拱形camshaft凸轮轴cantilever伸臂，悬臂；悬臂梁cap帽,罩cap nut螺冒capaciron电容汞弧管capacitance电容；电容量capstan lathe绞盘车床carburettor汽化器cardan shaft万向轴cartridge额盒式磁盘[带](机)；夹头cast投；掷；抛casting.铸件,铸造castle nut城堡螺母catalyst催化剂，触媒cathode阴极cathode-ray tube阴极射线管catwalk桥上人行道,狭小通道caulking填...以防漏。

风力发电专业术语名词中英文对照

风力发电专业术语名词中英文对照风力机wind turbine风电场wind power station wind farm风力发电机组wind turbine generator system水平轴风力机horizontal axis wind turbine垂直轴风力机vertical axis wind turbine轮毂（风力机）hub (for wind turbine)机舱nacelle支撑结构support structure for wind turbine关机shutdown for wind turbine正常关机normal shutdown for wind turbine紧急关机emergency shutdown for wind turbine空转idling锁定blocking停机parking静止standstill制动器brake停机制动parking brake风轮转速rotor speed控制系统control system保护系统protection system偏航yawing设计和安全参数design situation设计工况design situation载荷状况load case外部条件external conditions设计极限design limits极限状态limit state使用极限状态serviceability limit states极限限制状态ultimate limit state最大极限状态ultimate limit state安全寿命safe life严重故障catastrophic failure潜伏故障latent fault dormant failure风特性风速wind speed风矢量wind velocity旋转采样风矢量rotationally sampled wind velocity 额定风速rated wind speed切入风速cut-in speed切出风速cut-out speed年平均annual average年平均风速annual average wind speed平均风速mean wind speed极端风速extreme wind speed安全风速survival wind speed参考风速reference wind speed风速分布wind speed distribution瑞利分布RayLeigh distribution威布尔分布Weibull distribution风切变wind shear风廓线风切变律wind profile wind shear law风切变指数wind shear exponent对数风切变律logarithmic wind shear law风切变幂律power law for wind shear下风向down wind上风向up wind阵风gust粗糙长度roughness length湍流强度turbulence intensity湍流尺度参数turbulence scale parameter湍流惯性负区inertial sub-range风场wind site测量参数measurement parameters测量位置measurement seat最大风速maximum wind speed风功率密度wind power density风能密度wind energy density日变化diurnal variation年变化annual variation轮毂高度hub height风能wind energy标准大气状态standard atmospheric state风切变影响influence by the wind shear阵风影响gust influence风速频率frequency of wind speed环境environment工作环境operational environment气候climate cnwpme·com海洋性气候ocean climate大陆性气候continental climate露天气候open-air climate室内气候indoor climate极端extreme日平均值daily mean极端最高extreme maximum年最高annual maximum年最高日平均温度annual extreme daily mean of temperature 月平均温度mean monthly temperature空气湿度air humidity绝对湿度absolute humidity相对湿度relative humidity降水precipitation雨rain冻雨freezing rain霜淞rime雨淞glaze冰雹hail露dew雾fog盐雾salt fog雷暴thunderstorm雪载snow load标准大气压standard air pressure平均海平面mean sea level海拔altitude辐射通量radiant flux太阳辐射solar radiation直接太阳辐射direct solar radiation天空辐射sky radiation太阳常数solar constant太阳光谱solar spectrum黑体black body白体white body温室效应greenhouse effect环境温度ambient temperature表面温度surface temperature互联interconnection输出功率output power额定功率rated power最大功率maximum power电网连接点network connection point 电力汇集系统power collection system 风场电器设备site electrical facilities 功率特性power performance静电功率输出net electric power output 功率系数power performance自由流风速free stream wind speed。