模具零件常用英文单词
模具零件英语词汇
模具零件英语词汇3-plate mold 三板模2-plate mold 二板模leader pin/guide pin 边钉/导边bushing/guide bushing 边司/导套shoulder guide bushing 中托司guide pin 中托边ejector retainner plate 顶针板support plate 托板screw 螺丝dowel pin 管钉ply bar scot 开模槽core/cavity inter-lock 内模管位ejector pin 顶针ejector sleeve 司筒ejector pin 司筒针stripper plate 推板movable core,return core core puller 缩呵nylon latch lock 扣机（尼龙拉勾）lifter 斜顶mold base 模胚（架）cavity insert 上内模core insert 下内模slide 行位（滑块）insert 镶件wedge 压座/斜鸡wedge wear plate 耐磨板/油板plate 压条Lsupport pillar 撑头sprue bushing 唧嘴stop plate 挡板locating ring 定位圈latch 锁扣parting lock set 扣鸡push bar 推杆S.H.S.B 栓打螺丝eracuretun 顶板lever arm 活动臂spure sperader 分流锥bush 水口司stop pin 垃圾钉buffle 隔片spring rod 弹弓柱die spring 弹弓ejector guide bush 中托司ejector guide pin 中托边pin 镶针dowel pin 销子ball catch 波子弹弓pipe plug 喉塞lock plate 锁模块angle from pin 斜顶angle ejector rod 斜顶杆parting locks 尼龙拉勾lever arm 活动臂early return bar 复位键、提前回杆valves 气阀angle pin 斜导边terms 术语parting surface support balance 承压平面平衡parting line venting 模排气return pin and cavity interference 回针碰料位mold base shut hight 模总高超出啤机规格water line interferes withejector pin 顶针碰运水part from cavith (core) side 料位出上/下模cavity direct cut on A-plate,core direct cut on B-plate. 模胚原身出料位Do not use (core/cavity) insert 不准用镶件use beryllium copper insert 用铍铜做镶件preliinary (final) mold design 初步（正式）模图设计reverse core 反呵spring compressed length 弹弓压缩量good stability,stable 稳定性好insufficient rigidity 强度不够even cooling 均匀冷却sticking 扣模thero expansion 热膨胀tolorance 公差copper electrode 铜公(电极）top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板)outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location 定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block滑块sliding dowel block 滑块固定块active plate活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块mold [mEuld] n. 模子, 铸型vt. 浇铸, 塑造tooling [5tu:liN] v. 加工。
模具专业英语词汇.doc
模具专业英语词汇landed plunger mold 有肩柱塞式模具burnishing die 挤光模英语站landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具injection mold 注塑模rubber molding 橡胶成形hot chamber die casting 热室压铸sand mold casting 砂模铸造extrusion mold 挤出模multi-cavity mold 多模穴模具palletizing die 叠层模plaster mold 石膏模three plates mold 三板模plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模runner system浇道系统sprue/cold material trap 浇道/冷料井sprue puller 拉杆runner design 流道设计main runner 主流道secondary runner 次流道gate design 浇口设计submarine gate 潜伏浇口tunnel gate 隧道式浇口pinpoint gate 点浇口fan gate 扇形浇口side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口dish gate 盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣insulated runner/hot runner 热浇道runner plat 浇道模块valve gate阀门浇口slag well 冷料井cold slag 冷料渣sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) 注塑缺陷：flash 飞边warpage 翘曲air trap 积风blush 发赤flow line 流痕splay 银纹short shot 短射sink mark 缩痕streak 条纹void 缩孔weld line 熔接线gas mark 烧焦cold slug 冷斑delamination 起皮burr 毛刺flaw/scratch 刮伤gloss 光泽glazing 光滑surface check 表面裂痕hesitation 迟滞注塑工艺:molding conditions 成型条件drying 烘干barrel temperature 料筒温度melt temperature 熔化温度mold temperature 模具温度injection pressure 注塑压力back pressure 背压injection speed 注塑速度screw speed 螺杆转速tensile strength 抗拉强度tensile elongation 延伸率flexural modulus 弯曲模数flexural strength 抗弯强度shrinkage 收缩率regrind usage 次料使用机械设备:lathe车床planer |刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机punching machine 冲床robot机械手common equipment常用设备EDM=Electron Discharge Machining 放电加工3D coordinate measurement 三次元量床boring machine 搪孔机milling machine 铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床模具零件:top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot 撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate 不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodAabrasion n. 磨损mósǔnabrasion resistance n. 耐磨损性 nài mósǔn xìngabrasive n. 磨料 móliàoaccelerator n. 促进剂 cùjìnjìaccuracy n. 准确性zhǔnquèxìngacrylic n. 丙烯酸bǐngxīsuān，压克力yākelìadditive n. 添加剂tiānjiājìadhere v. 黏附 niánfùadhesion n. 黏合 niánhéadhesive n. 胶粘剂jiāozhānjìair entrapment n. 困气 kùnqìanneal v. 退火tùihuǒassemble v. 总成zǒngchéngBbarrel n. 机筒jītǒng，料筒liàotǒngblow molding n. 吹塑成型chūisù chéngxíngblow molding machine n. 吹塑机chūisùjībrittle adj. 脆性 cùixìngbubble n. 气泡 qìpàoby-product n. 副产品fùchǎnpǐnCcalendering n. 压延yāyáncarbon steel n. 碳素钢 tànsùgāngcasting n. 铸造 zhùzàocatalyst n. 催化剂cūihuàjìcavity n. 型腔xíngqiāngchemical resistance n. 耐化学腐蚀性 nài huàxuéfǔshí xìngchip v. 削xiāo，凿 záoclamping force n. 锁模力suǒmólìclamping tonnage n. 锁模吨位suǒmódūnwèicomputer aided design (CAD) n. 电脑辅助设计diànnǎo fǔzhù shèjìcomputer aided manufacture (CAM) n. 电脑辅助制造diànnǎo fǔzhù zhìzào computer numerical control (CNC) n. 电脑数字控制diànnǎo shùzì kòngzhìceramic n. 陶瓷 táocícold rolled steel n. 冷轧圆钢lěng zháyuán gāngcold runner n. 冷流道lěng liúdàocolorant n. 着色剂 zhuósèjìcomposite n. 复合材料 fùhé cáiliàocompression strength n. 抗压强度kàngyā qiángdùcooling channel/circuit n. 冷却管道lěngquèguǎndàocooling rate n. 冷却速率lěngq uèsùlǜcore n. 型芯xíngxīn，模芯móxīncorrosion n. 腐蚀fǔshícorrosion resistance n. 耐腐蚀性 nài fǔshí xìngcure v. 固化 gùhuàcustom adj. 定制 dìngzhìcycle time n. 循环时间 xúnhuán shíjiānDdegassing n. 排气 páiqìdensity n. 密度 mìdùdeform v. 变形 biànxíngdie n. 冲模 chòngmódie casting n. 压铸yāzhù，模铸 mózhùdimension n. 尺寸chǐcùndimensional tolerance n. 尺寸公差chǐcùn gōngchàdistort v. 扭曲niǔqūdraft angle n. 拨模斜度bōmó xiédùdwell time n. 驻留时间 zhùliúshíjiāndye n. 染料 ránliàoEejector mark n. 顶出痕迹dǐngchū hénjìejection pin n. 顶出杆dǐngchūgān，推顶锁tūidǐng suǒ，脱模锁tuōmósuǒejection plate n. 推顶板tūidǐng bǎn，脱模板tuōmóbǎnejection rod n. 脱模板拉杆tuōmóbǎn lāgānelastomer n. 弹性体tánxìngtǐelectrical discharge machining (EDM) n. 电火花加工diànhuǒhuājiāgōng epoxy n. 环氧树脂huányǎngshùzhīextruder n. 挤出机jǐchūjīextrusion n. 挤出jǐchū，挤塑jǐsùFfabricate v. 制造 zhìzàofiber n. 纤维xiānwéifiberglass n. 玻璃纤维bōli xiānwéifiber reinforcement n. 纤维增强xiānwéi zēngqiángfilm n. 薄膜 báomófire retardant n. 阻燃剂zǔránjìflash n. 溢料 yìliàoflow mark n. 流痕 liúhénflow rate n. 流动速率 liúdòng sùlǜfluorescent adj. 荧光yíngguāngfluorescent brightener n. 荧光增白剂yíngguāng zēngbáijìfoam n. 泡沫 pàomòfuse v. 熔合 rónghéGgas assisted injection molding n. 气辅注射成型qìfǔ zhùshè chéngxíng gate n. 浇口jiāokǒugate mark n. 浇口痕jiāokǒu héngear n. 齿轮chǐlúngrinder n. 研磨机yánmójī，磨床 móchuángHheat conduction n. 热传导 rè chuándàoheater band n. 加热圈jiārèquānheat treatment n. 热处理 rèchǔlǐhigh density polyethylene (HDPE) n. 高密度聚乙烯gāo mìdùjùyǐxīhigh impact plastic n. 高抗冲塑料gāo kàngchòng sùliàohigh impact polystyrene n. 高抗冲聚苯乙烯gāo kàngchòng jùběnyǐxīhobbing n. 滚铣gǔnxǐ，挤压制模jǐyā zhìmó，切压制模qiēyā zhìmóholding n. 保压bǎoyāhot runner n. 热流道 rè liúdàoIimpact strength n. 冲击强度chòngjī qiángdùinjection n. 注射 zhùshè，注塑 zhùsùinjection molding n. 注塑成型 zhùsù chéngxínginjection molding machine n. 注塑机zhùsùjīinjection pressure n. 注塑压力 zhùsùyālìinsulated runner n. 绝热流道 juérè liúdào，保温流道bǎowēn liúdào insulation layer n. 绝热层 juérè cénginternally heated runner n. 内加热流道 nèi jiārè liúdàointernal void n. 内部空腔 nèibùkōngqiāngJjoint n. 接头jiētóu，连接liánjiēLlaser n. 激光jīguānglaser cutter n. 激光切割机jīguāng qiēgējīlathe n. 车床chēchuánglocating pin n. 定位锁 dìngwèi suǒlow density polyethylene n. 低密度聚乙烯dī mìdùjùyǐxīMmelt v. 熔融 róngróngmelt index n. 熔融指数 róngróng zhǐshùmill (metal) v. 铣xǐmachining n. 机加工jījiāgōngmachining path n. 加工路径jiāgōng lùjìng manufacture v. 制造 zhìzàomeld line n. 融合线 rónghé xiànmetal machining n. 金属加工jīnshùjiāgōngmilling machine n. 铣床xǐchuángmodel n. 模型 móxíngmonomer n. 单体dāntǐmold n. 模具 mójùmold cavity n. 模具型腔 mójùxíngqiāngmold life n. 模具寿命 mójù shòumìngmulticavity mold n. 多腔模具duōqiāng mójùmulticolor injection molding n. 多色注塑duōsè zhùsùmultigate mold n. 多浇口模具duōjiāokǒu mójùmultishot injection molding n. 多色注塑duōsè zhùsùNnozzle n. 喷嘴pēnzǔiNylon n. 尼龙 NílóngOoxidation resistance n. 耐氧化性 nài yǎnghuà xìng oxidize v. 氧化yǎnghuàPpackaging n. 包装bāozhuāngpacking n. 补料bǔliàoparison n. 型坯xíngpīpart n. 零件 língjiànparting line n. 分模线fēnmóxiànparting plane n. 分模面fēnmómiànpinhole gate n. 针孔形浇口zhēnkǒngxíng jiāokǒuplastic n. 塑料 sùliàoplasticity n. 塑性 sùxìngplasticizer n. 增塑剂zēngsùjìplotter n. 绘图机hùitújīpolish v. 抛光pāoguāngpolycarbonate (PC) n. 聚碳酸酯jùtànsuānzhǐpolyethylene n. 聚乙烯jùyǐxīpolyester n. 聚酯jùzhǐpolymer n. 聚合物（体）jùhéwù(tǐ)，高聚物gāojùwùpolymerization n. 聚合 jùhépolystyrene n. 聚苯乙烯jùběnyǐxīpolyurethane n. 聚氨脂jù'ānzhīpolyvinyl chloride (PVC) n. 聚氯乙烯jùlǜyǐxīporous adj. 多孔duōkǒngprecise adj. 精密jīngmìprecision n. 精度jīngdùprecision injection machine n. 精密注塑机jīngmìzhùsùjīprecision molding n. 精密模塑jīngmì mósùpreform n. 预成型 yùchéngxíngpreform molding n. 预成型模塑 yùchéngxíng mósùprocess v. 处理chǔlǐ；加工jiāgōngproduction line n. 生产线shēngchǎnxiànprototype n. 原型 yuánxíngpunch n. 冲头 chòngtóuQquench v. 淬火cùihuǒRregrind n. 回用料 húiyòngliàoresin n. 树脂shùzhīrib n. 肋条 lèitiáorib stiffener n. 加强肋jiāqiáng lèirigidity n. 刚性gāngxìngripple n. 波纹bōwén，皱纹 zhòuwénrough adj. 粗糙cūcāorubber n. 橡胶xiàngjiāo；橡皮 xiàngpírunner n. 流道 liúdàorunnerless adj. 无流道 wúliúdàorunnerless injection mold n. 无流道注塑模具 wúliúdào zhùsù mójùSscale n. 比例bǐlìschematic n. 图解tújiěseal v. 密封mìfēn gshort shot n. 短射duǎnshè，欠料注射 qiànliào zhùshèshot n. 注料 zhùliào，注射 zhùshèshot size n. 注塑量 zhùsùliàngshrinkage n. 收缩shōusuōside core n. 侧性芯cèxìngxīnside gate n. 侧向浇口 cèxiàng jiāokǒusilicone n. 聚硅氧烷jùgūiyǎngwánsilicone rubber n. 硅橡胶gūixiàngjiāosimulate v. 模拟mónǐsingle cavity mold n. 单腔模具dān qiāng mójùsingle gate mold n. 单浇口模具dān jiāokǒu mójùsink mark n. 凹痕āohén，缩痕suōhénslide n. 滑动阀 huádòngfásoftener n. 软化剂ruǎnhuàjìsprue n. 注道 zhùdàosteam channel n. 汽道 qìdàostabilizer n. 稳定剂wěndìngjìstamping n. 冲压chòngyāstainless steel n. 不锈钢bùxiùgāngstrain n. 应变 yìngbiànstreak n. 条纹 tiáowén，条痕 tiáohénstress n. 应力 yìnglìstripper n. 脱模器tuōmóqì，顶出器dǐngchūqìstripper ring n. 脱模圈tuōmóquānsurface defect n. 表面缺陷biǎomiàn quēxiànsurface treatment n. 表面处理biǎomiàn chǔlǐsymmetrical adj. 对称dùichēngsymmetry n. 对称dùichēngTtie bar n. 连接杆liánjiēgānTeflon n. 特氟隆 Tèfúlóngtemper v. 回火hùihuǒtensile strength n. 抗张强度kàngzhāng qiángdùthermoforming n. 热成型 rèchéngxíngthermoplastic n. 热塑性塑料 rèsùxìng sùliào adj. 热塑性 rèsùxìng thermoset n. 热固性塑料 règùxìng sùliào adj. 热固性 règùxìngthree-dimensional adj. 三维空间sānwéi kōngjiāntolerance n. 公差gōngchàtool mark n. 刀痕dāohéntool steel n. 工具钢gōngjùgāngUultrasonic welder n. 超声波焊接机chāoshēngbōhánjiējīundercut n. 凹孔āokǒngunit cost n. 单价dānjiàVvacuum n. 真空zhēnkōngvented injection molding n. 排气式注塑成型 páiqìshì zhùsù chéngxíng viscosity n. 黏度 niándù，黏性 niánxìngvulcanize v. 硫化 liúhuàWwarpage n. 翘曲变形qiàoqū biànxíngwear n. 磨损mósǔnwear resistance n. 耐磨损性 nài mósǔn xìngweld line n. 熔接线róngjiē xiànworking drawing n. 工程图根据国家标准，以下为部分塑料模具成形术语的标准翻译。
模具部件英文表达
简写取单词头个字母top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子baffle plate挡块located block定位块supporting block for location定位支承块guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块bushing bolck衬套cover plate盖板guide pad导料块顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot 撑头: support pillar 唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge公差：tolorance铜公(电极）：copper electroMold Design 模具设计Drawings 图纸Order Mold Base 订购模具基座Core Milling 铣模具芯Cavity Milling 铣模具腔Core Drilling 钻模芯Cavity Drilling 钻模腔Inserts Milling 铣滑块Fitting Inserts 把滑块定位好Injection System 注射系统Mold Assembling 模具组装Tec. Polish 抛光1st Trial Injection 初次试模Several Corrections 几个改正FFinal Trial Injectioninish Polish & Texture 最终试模抛光和表面纹理处理Part Name: 部件名称定模底板Top Clamping plate 锁紧块Jaw定模板Cavity plate(A-plate) 导滑块Gib动模板Core plate(B-plate) 滑块定位夹Slide retainer支撑板Support plate 弹簧波子Ball pluger模脚Spacer Block 油缸Hydraulic cylinder顶杆固定板Ejector retainer plate 齿轮Gear顶杆垫板Ejector plate 齿条Rack动模底板Bottom plate 轴承Bearing定位圈Locating Ring 方顶Blade Ejector浇口套Sprue Bushing 扁顶Blade Ejector导柱Guide Pin 发热线Heater导套Guide Bushing 发热管Probe顶杆Ejector Pin 接线盒Connector顶管Ejector Sleeve 斜顶Lifter拉料杆Sprue puller pin 行程开关Limit switch复位杆Return pin 模架Mold base限位钉Stop-pin 热流道板Manifold定模镶块Cavity insert Block 直身锁Straight interlock动模镶块Core insert Block 斜度锁Tappered interlock推板导柱Ejector Guide pin 限位螺钉Stripper Bolt推板导套Ejector Guide bushing 安全锁Safety Strap内交角螺钉Socket head screw 盖板Cover Plate定位销Dowel pin 连接器Adaptor弹簧Spring 隔热板Insulating Sheet推板Striper 镶针Core pin水管螺塞Plug 顶棍连接器K.O.Adaptor橡胶圈“o”Ring 滑块镶件Slide insert隔水片Baffle 热嘴Hot sprue bushing支撑住Support pillar 喷嘴座Nozzle Seat 小内模件Sub-insert 旋转螺杆Screw core 滑块Slide 支架板Mounting plate斜导柱Angle pin 冷却管Cascade Tube 耐磨片Wear plate 面板Clamping plate。
模具基础英语
模具基础英语模具基础英语模具基础英语大家都会吗?都知道模具基础英语有哪些吗?下面，店铺为大家分享模具基础英语，希望对大家有帮助!模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机(尼龙拉勾)：nylon latch lock斜顶：lifter模胚(架)：mold base上内模：cavity insert下内模：core insert行位(滑块)：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance 模排气：parting line venting下载文档润稿写作咨询。
模具(机械)英语词汇表
GLOSSARYAabrasive grinding 強力磨削abrasive[☜'breisiv] a.磨料的, 研磨的absence ['✌bs☜ns] n.. 不在，缺席accesssory[✌k'ses☜ri] n.附件accommodate[☜'k m☜deit] v. 適應accordingly[☜'k :di☠li] adv.因此,從而,相應地accuracy['✌kjur☜si] n精度,準確性actuate['✌ktjueit] vt.開動(機器), 驅動adequate['✌dikwit] a. 足夠的adhesive[☜d'hi:siv] n. 粘合劑adjacent[☜'d✞eisnt] a. 鄰近的adopt[☜'d pt] vt. 採用advance [☜d'v✌:ns] n.進步advisable [☜d'vaizbl] adj. 可取的 L20 agitate['✌d✞iteit] v. 搖動a large extent 很大程度algorithm ['✌l♈☜ri❆☜m] n. 演算法align [☜'lain] v 定位，調准alignment[☜'lainm☜nt] n. 校直all-too-frequent 頻繁allowance[☜'l☜uens] n. 容差, 餘量alternate[' :lt☜nit]v.交替,輪流alternative[ :l't☜:n☜tiv] n. 替換物alternatively[ :l't☜:n☜tivli] ad. 做為選擇, 也許aluminiun[ ✌lju'minj☜m] n.鋁ample['✌mpl] adj. 充足的analysis [☜'n✌l☜sis] n. 分析ancillary['✌nsil☜ri] a.補助的, 副的angular ['✌♈jul☜] adj. 有角的annealing[☜'li:li☠] n.退火aperture ['✌p☜t☞☜] n.孔applied loads 作用力appropriate [☜'pr☜uprieit] a. 適當的arc[a:k] n.弧, 弓形arise[☜'raiz] vi. 出現, 發生arrange[☜'reid✞] v. 安排article['a:tikl] n.製品, 產品ascertain[ ✌s☜'tein] vt. 確定, 查明assemble[☜'sembl] vt.組裝attitude ['✌titju:d] n 態度auxiliary [ :♈'zilj☜ri]adj. 輔助的avoid[☜'v id] v.避免axis['✌ksis] n.軸axle['✌ksl] n.輪軸, 車軸Bbackup['b✌k ✈p] n. 備份batch [b✌t☞] n 一批bearing['b☪☜ri☠] n.軸承,支座bed[bed] n. 床身behavior[bi'heivj☜] n. 性能bench-work 鉗工工作bend[bend] v.彎曲beneath[bi'ni: ] prep在···下bin [bin] n. 倉，料架blank [bl✌☠k] n. 坯料blank [bl✌☠k] v. 沖裁,落料blanking tool 落料模blast [bl✈st] n.一陣（風）blemish['blemi☞] n. 缺點, 污點bolster['b☜ulst☜] n. 模座,墊板boost[bu:st] n. 推進boring['b :ri☠] n.鏜削, 鏜孔bracket ['br✌kit] n. 支架brass [br✌s] n.黃銅break down 破壞breakage ['breikid✞] n.破壞bridge piecebrine[brain] n. 鹽水brittle['britl] adv.易碎的121buffer [b✈f☜] n.緩衝器built-in 內裝的bulging [b✈ld✞i☠] n. 击肚burr [b☜:] n. 毛刺bush [bu☞] n. 襯套bush[bu☞]n. 襯套by far (修飾比較級, 最高級)···得多, 最by means of 借助於Ccabinet ['k✌binit] n.櫥櫃call upon 要求carbide['ka:baid] n.碳化物carburzing['ka:bjureti☠] n. 滲碳carriage['k✌rid✞] n.拖板, 大拖板L5 carry along 一起帶走carry down over 從···上取下L21 carry out 完成case hardening 表面硬化case[keis] n. 殼, 套cast steel 鑄鋼casting['ka:sti☠] n. 鑄造,鑄件category['k✌t☜♈☜uri] n. 種類caution ['k :☞☜n] n. 警告，警示cavity and core plates 凹模和击範本cavity['k✌viti] n.型腔, 腔, 洞centre-drilling 中心孔ceramic[si'r✌mik] n.陶瓷製品chain doted line 點劃線channel['t☞✌nl] n.通道, 通道characteristic[k✌r☜kt☜'ristik] n.特性check[t☞ek] v.核算chip[t☞ip] n.切屑, 鐵屑chuck [t☞✈k] n.卡盤chute [☞u:t] n. 斜道circa ['s☜k☜:] adv. 大約circlip['s☜:klip] n.(開口)簧環circuit['s☜:kit] n. 回路, 環路circular supoport block circulate['s☜:kjuleid] v.(使)迴圈clamp [kl✌mp] vt 夾緊clamp[kl✌mp] n.壓板clay[klei] n. 泥土clearance ['kli☜r☜ns] n. 間隙clip [klip] vt. 切斷，夾住cold hobbing冷擠壓cold slug well 冷料井collapse[k☜'l✌ps] vi.崩塌, 瓦解collapsible[k☜'l✌ps☜bl] adj.可分解的combination [k mbi'nei☞☜n] n. 組合commence[k☜'mens] v. 開始, 著手commence[k☜'mens]v. 開始commercial [k☜'m☜:☞☜l] adj. 商業的competitive[k☜m'petitiv] a. 競爭的complementary[ k mpli'ment☜ri] a. 互補的complexity [kem'pleksiti] n.複雜性complicated['k mpl☜keitid] adj.複雜的complication [k mpli'kei☞☜n] n. 複雜化compression [k☜m'pre☞☜n] n.壓縮comprise[k☜m'prais] vt.包含compromise['k mpr☜maiz] n. 妥協, 折衷concern with 關於concise[k☜n'sais] a. 簡明的, 簡練的confront[k☜n'fr✈nt] vt. 使面臨connector[k☜'nekt☜] n. 連介面, 接頭consequent['k nsikw☜nt] a. 隨之發生的, 必然的console ['k nsoul] n.控制臺consume [k☜n'sjum] vt. 消耗, 佔用consummate [k☜n's✈meit] vt. 使完善container[k☜n'tein☜] n. 容器contingent[ken'tind✞☜nt] a.可能發生的contour['k☜ntu☜] n.輪廓conventional[k☜n'ven☞☜nl] a. 常規的converge[k☜n'v☜:d✞] v.集中於一點conversant[k n'v☜:s☜nt] a. 熟悉的122conversion[k☜n'v☜:☞☜n] n 換算, 轉換conveyer[ken'vei☜] n. 運送裝置coolant['ku:l☜nt] n. 冷卻液coordinate [k☜u' :dnit] vt. (使)協調copy machine 仿形(加工)機床core[k :] n. 型芯, 核心corresponding [ka:ri'sp di☠] n.相應的counteract [kaunt☜'r✌kt] vt. 反作用,抵抗couple with 伴隨CPU (central processing unit) 中央處理器crack[kr✌k ] v.（使）破裂，裂紋critical['kritikl] adj.臨界的cross-hatching 剖面線cross-section drawn 剖面圖cross-slide 橫向滑板CRT (cathoder-ray tube) 陰極射線管crush[kr✈☞]vt.壓碎cryogenic[ krai☜'d✞enik ]a.低溫學的crystal['kristl] adj.結晶狀的cubic['kju:bik] a. 立方的, 立方體的cup [k✈p] vt (使)成杯狀, 引伸curable ['kjur☜bl] adj. 可矯正的curvature['k☜:v☜t☞☜] n.弧線curve [k☜:v] vt. 使彎曲cutter bit 刀頭, 刀片cyanide['sai☜naid] n.氰化物Ddash [d✌☞] n. 破折號daylight ['deilait] n. 板距decline[di'klain] v.下落,下降,減少, deform[di'f :m] v. (使)變形demonstrate['dem☜streit ] v證明depict[di'pikt ] vt 描述deposite [di'p zit] vt. 放置depression[di'pre☞☜n] n. 凹穴descend [di'sent] v. 下降desirable[di'zair☜bl] a. 合適的detail ['diteil] n.細節，詳情deterioration[diti☜ri:☜'rei☞☜n] n. 退化, 惡化determine[di't☜:min] v.決定diagrammmatic[ dai☜gr☜'m✌tik].a.圖解的，圖表的L10 dictate['dikteit] v. 支配die[dai] n.模具, 沖模, 凹模dielectric[daii'lektrik] n. 電介質die-set 模架digital ['did✞itl ] n.數位式數位, a.數字的dimensional[dddi'men☞☜nl] a. 尺寸的, 空間的discharge[dis't☞a:d✞] n.v. 放電, 卸下, 排出discharge[dis't☞a:d✞] v.卸下discrete [dis'cri:t] adj. 離散的,分立的dislodge[dis'l d✞] v. 拉出, 取出 L12 dissolution[dis☜'lu:☞☜n] n.結束distinct [dis'ti☠kt] a.不同的，顯著的distort [dis'd :t] vt. 扭曲distort[dis't :t] vt. (使)變形, 扭曲distributed system 分散式系統dowel ['dau☜l] n. 銷子dramaticlly [dr☜'m✌tikli] adv. 顯著地drastic ['dr✌stik] a.激烈的draughting[dra:fti☠] n. 繪圖draughtsman['dr✌ftsm☜n] n. 起草人drawing['dr :i☠] n. 製圖drill press 鑽床drum [dr✈m] n.鼓輪dual ['dju:☜l] adv. 雙的，雙重的ductility [d✈k'tiliti ] n.延展性dynamic [dai'n✌mik ] adj 動力的Eedge [ed✞] n .邊緣e.g.(exempli gratia) [拉] 例如ejector [i'd✞ekt☜] n.排出器，ejector plate 頂出板ejector rob 頂杆123elasticity[il✌'stisiti] n.彈性electric dicharge machining 電火花加工electrical discharge machining電火花加工electrochemical machining 電化學加工electrode[i'lektr☜ud] n. 電極electro-deposition 電鑄elementary [el☜'ment☜ri] adj.基本的eliminate[i'limineit] vt. 消除, 除去elongate[i'l ☠♈et] vt. (使)伸長, 延長emerge [i'm☜:d✞] vi. 形成, 顯現emphasise['emf☜saiz] vt. 強調endeavour[en'dev☜] n. 盡力engagement[in'♈eid✞ment] n. 約束, 接合enhance[in'h✌ns] vt. 提高, 增強ensure [in'☞u☜] vt. 確保，保證envisage[in'vizid✞] vt.設想erase[i'reis] vt. 抹去, 擦掉evaluation[i'v✌lju ei☞☜n] n. 評價, 估價eventually[i'v☜nt☞u☜li ] adv.終於evolution[ev☜'lu:☞☜n] n.進展excecution[eksi'kju:☞☜n] n. 執行, 完成execute ['ekskju:t] v. 執行exerte [i♈'z☜:t] vt. 施加experience[iks'piri☜ns] n. 經驗explosive[iks'pl☜usiv]adj.爆炸(性)的L22 extend[eks'tend] v. 伸展L2 external[eks't☜:nl] a. 外部的L5,11 extract[eks'tr✌kt] v. 拔出L14 extreme[iks'tri:m] n. 極端L13 extremely[iks'tri:mli] adv. 非常地 L12 extremity[iks'tmiti] n. 極端L13 extrusion[eks'tru:✞☜n] n. 擠壓, 擠出L3 FF (Fahrenheit)['f✌r☜nhait]n.華氏溫度fabricate ['f✌brikeit] vt.製作,製造facilitate [f☜'siliteit] vt. 説明facility[f☜'siliti] n. 設備facing[feisi☠] n. 端面車削fall within 屬於, 適合於fan[f✌n] n.風扇far from 毫不, 一點不, 遠非fatigue[f☜'ti♈] n.疲勞feasible ['fi:z☜bl] a 可行的feature ['fi:t☞☜] n.特色, 特徵feed[fi:d] n.. 進給feedback ['fi:db✌k] n. 回饋female['fi:meil] a. 陰的, 凹形的ferrule['fer☜l] n. 套管file system 檔系統fitter['fit☜] n.裝配工, 鉗工fix[fiks] vt. 使固定, 安裝, vi. 固定fixed half and moving half 定模和動模flat-panel technology 平面(顯示)技術flexibility[fleksi'biliti] n. 適應性, 柔性flexible['fleks☜bl] a. 柔韌的flow mark 流動斑點follow-on tool 連續模foregoing ['f :'♈☜ui☠]adj. 在前的,前面的foretell[f :'tell] vt. 預測, 預示, 預言forge[f :d✞] n. v. 鍛造forming[f :mi☠] n. 成型four screen quadrants 四螢幕象限fracture['fr✌kt☞☜] n.破裂free from 免於Ggap[♈✌p] n. 裂口, 間隙L10 gearbox['♈i☜b ks] n.齒輪箱L5 general arrangement L16 govern['♈✈v☜n] v.統治, 支配, 管理 L13 grain [♈rein] n. 紋理L20 graphic ['♈r✌fik] adj. 圖解的L6 grasp [♈r✌sp] vt. 抓住L8 grid[♈rid] n. 格子, 網格L16 grind[♈raind] v. 磨, 磨削, 研磨L3 grinding ['♈raindi☠] n. 磨光,磨削L3,20124grinding machine 磨床L5 gripper[♈rip☜] n. 抓爪, 夾具L9 groove[♈ru:v] n. 凹槽L12 guide bush 導套L5 guide pillar 導柱L5 guide pillars and bushes 導柱和導套L11 Hhandset['h✌ndset] n. 電話聽筒L4 hardness['ha:dnis] n.硬度L1,2 hardware ['ha:dw☪☜] n. 硬體L6 headstock['hedst k] n.床頭箱, 主軸箱L5 hexagonal[hek's✌♈☜nl] a. 六角形的, 六角的L11 hindrance['hindr☜ns] n.障礙, 障礙物L11 hob[h b] n. 滾刀, 沖頭L4 hollow-ware 空心件L21 horizontal[h ri'z ntl] a. 水準的L16 hose[h☜uz] n. 軟管, 水管L13 hyperbolic [haip☜'b lik] adj.雙曲線的L7 Ii.e. (id est) [拉] 也就是L12 identical[ai'dentikl] a同樣的L16 identify [ai'dentifai] v. 確定, 識別L7 idle ['aidl] adj.空閒的L8 immediately[i'mi:dj☜tli] adv. 正好, 恰好L12 impact['imp✌kt] n.衝擊L1 impart [im'pa:t] v.給予L11,17 implement ['implim☜nt] vt 實現L6 impossibility[imp s☜'biliti] n.不可能L21 impression[im'pre☞☜n] n. 型腔L11 in contact with 接觸L1 in terms of 依據L1 inasmuch (as)[in☜z'm✈t☞] conj.因為, 由於L3 inch-to-metric conversions 英公制轉換L7 inclinable [in'klain☜bl] adj. 可傾斜的L20 inclusion [in'klu☞☜n] n. 內含物L19 inconspicuous[ink☜n'spikju☜s] a. 不顯眼的L14 incorporate [in'k :p☜reit] v 合併,混合L17 indentation[ inden'tei☞☜n ] n.壓痕L1 indenter[in'dent☜] n. 壓頭L1 independently[indi'pein☜ntli] a. 獨自地, 獨立地L16 inevitably[in'evit☜bli] ad. 不可避免地L14 inexpensive[inik'spensiv]adj. 便宜的L2 inherently [in'hi☜r☜ntli] adv.固有的L7 injection mould 注塑模L11 injection[in'd✞ek☞☜n] n. 注射L11in-line-of-draw 直接脫模L14 insert[in's☜:t] n. 嵌件L16inserted die 嵌入式凹模L19 inspection[in'spek☞☜n] n.檢查,監督L9 installation[inst☜'lei☞☜n] n. 安裝L10integration [inti'♈rei☞☜n] n.集成L6intelligent[in'telid✞☜nt]a. 智能的L9intentinonally [in'ten☞☜n☜li] adv 加強地，集中地L17 interface ['int☜feis] n.. 介面L6 internal[in't☜:nl] a. 內部的L1,5 interpolation [int☜p☜'lei☞☜n] n.插值法L7investment casting 熔模鑄造L4 irregular [i'regjul☜] adj. 不規則的，無規律L17 irrespective of 不論, 不管L11 irrespective[iri'spektiv] a. 不顧的, 不考慮的L11issue ['isju] vt. 發佈，發出L6J125joint line 結合線L14 Kkerosene['ker☜si:n] n.煤油L10 keyboard ['ki:b :d ] n. 健盤L6 knock [n k] v 敲，敲打L17 Llance [la:ns] v. 切縫L19 lathe[lei❆] n. 車床L4 latitude ['l✌titju:d] n. 自由L17 lay out 佈置L13 limitation[limi'tei☞☜n] n.限度,限制,局限(性)L3 local intelligence局部智慧L9 locate [l☜u'keit] vt. 定位L18 logic ['l d✞ik] n. 邏輯L7 longitudinal['l nd✞☜'tju:dinl] a. 縱向的L5 longitudinally['l nd✞☜'tju:dinl] a. 縱向的L13look upon 視作, 看待L17 lubrication[lju:bri'kei☞☜n ] n.潤滑L21 Mmachine shop 車間L2 machine table 工作臺L8 machining[m☜'☞i:ni☠] n. 加工L3 made-to-measure 定做L15 maintenance['meintin☜ns] n.維護,維修L7 majority[m☜'d✞a:riti] n.多數L21 make use of 利用L2 male[meil] a. 陽的, 击形的L11 malfunction['m✌l'f✈☠☞☜n] n. 故障L9 mandrel['m✌dtil] n.心軸L22 manifestation[m✌nif☜s'tei☞☜n] n. 表現, 顯示L9 massiveness ['m✌sivnis ] 厚實，大塊L19 measure['me✞☜] n. 大小, 度量L1 microcomputer 微型電腦L9 microns['maikr n] n.微米L10 microprocessor 微處理器L9 mild steel 低碳鋼L17 milling machine 銑床L4 mineral['min☜r☜l] n.礦物, 礦產L2 minimise['minimaiz] v.把···減到最少, 最小化L13 minute['minit] a.微小的L10 mirror image 鏡像L16 mirror['mir☜] n. 鏡子L16 MIT (Massachusetts Institute of Technology) 麻省理工學院L7 moderate['m d☜rit]adj. 適度的L1,2 modification [m difi'kei☞☜n ] n. 修改, 修正L6 modulus['m djul☜s] n.係數L1 mold[m☜uld] n. 模, 鑄模, v. 制模, 造型L3 monitor ['m nit☜ ] v. 監控L6 monograph['m n☜♈ra:f] n. 專著L4more often than not 常常L20 motivation[m☜uti'vei☞☜n] n. 動機L9 mould split line 模具分型線L12 moulding['m☜udi☠] n. 注塑件L5,11 move away from 拋棄L17 multi-imprssion mould 多型腔模L12 Nnarrow['n✌r☜u] a. 狹窄的L12 NC (numerical control ) 數控L7 nevertheless[ nev☜❆☜'les] conj.,adv.然而,不過L11 nonferrous['n n'fer☜s] adj.不含鐵的, 非鐵的L2 normally['n :mli]adv.通常地L22 novice['n vis] n. 新手, 初學者L16 nozzle['n zl] n. 噴嘴, 注口L12 numerical [nju'merikl] n. 數字的L6 Oobjectionable [☜b'd✞ek☞☜bl] adj. 有異議126的，討厭的L17 observe[☜b'z☜:v] vt. 觀察L2 obviously [' bvi☜sli] adv 明顯地L17 off-line 脫機的L6 on-line 聯機L9 operational [ p☜'rei☞☜nl] adj.操作的, 運作的L8 opportunity[ p☜'tju:niti] n. 時機, 機會L13 opposing[☜'p☜uzi☠] a.對立的, 對面的L12 opposite[' p☜zit] n. 反面L1a.對立的,對面的L12 optimization [ ptimai'zei☞☜n] n.最優化L6 orient [' :ri☜nt] vt. 確定方向L8 orthodox [' : ☜d ks] adj. 正統的，正規的L19 overall['☜uv☜r :l] a.全面的,全部的L8,13 overbend v.過度彎曲L20 overcome[☜uv☜'k✈m] vt.克服, 戰勝L10 overlaping['☜uv☜'l✌pi☠] n. 重疊L4 overriding[☜uv☜'raidi☠] a. 主要的, 佔優勢的L11 Ppack[p✌k] v. 包裝L2 package ['p✌kid✞] vt.包裝L7 pallet ['p✌lit] n.貨盤L8 panel ['p✌nl] n.面板L7 paraffin['p✌r☜fin] n. 石蠟L10 parallel[p✌r☜lel] a.平行的L5 penetration[peni'trei☞☜n ] n.穿透L1peripheral [p☜'rif☜r☜l] adj 週邊的L6 periphery [p☜'rif☜ri] n. 週邊L18 permit[p☜'mit] v. 許可, 允許L16 pessure casting 壓力鑄造L4 pillar['pil☜] n. 柱子, 導柱L5,17 pin[pin] n. 銷, 栓, 釘L5,17 pin-point gate 針點式澆口L12 piston ['pist☜n] n.活塞L1 plan view 主視圖L16 plasma['pl✌zm☜] n. 等離子L9 plastic['pl✌stik] n. 塑膠L3 platen['pl✌t☜n] n. 壓板L12 plotter[pl t☜] n. 繪圖機L9 plunge [pl✈nd✞] v翻孔L18 plunge[pl✈nd✞] v.投入L2 plunger ['pl✈nd✞☜ ] n. 柱塞L19 pocket-size 袖珍L9 portray[p :'trei] v.描繪L21 pot[p t] n.壺L21 pour[p :] vt. 灌, 注L22 practicable['pr✌ktik☜b] a. 行得通的L14 preferable['pref☜r☜bl] a.更好的, 更可取的L3 preliminary [pri'limin☜ri] adj 初步的，預備的L19 press setter 裝模工L17 press[pres] n.壓,壓床,衝床,壓力機L2,8 prevent [pri'vent] v. 妨礙L20 primarily['praim☜rili] adv.主要地L4 procedure[pr☜'si:d✞☜] n.步驟, 方法, 程式L2,16 productivity.[pr☜ud✈k'tiviti] n. 生產力L9 profile ['pr☜ufail] n.輪廓L10 progressively[pr☜'♈resiv] ad.漸進地L15 project[pr☜'d✞ekt] n.項目L2 project[pr☜'d✞ekt] v. 击出L11 projection[pr☜'d✞ek☞☜n] n.突出部分L21proper['pr p☜] a. 本身的L10 property['pr p☜ti] n.特性L1 prototype ['pr☜ut☜taip] n. 原形L7proximity[pr k'simiti] n.接近L9 prudent['pru:d☜nt] a. 謹慎的L16 punch [p✈nt☞] v. 沖孔L3127punch shapper tool 刨模機L17 punch-cum-blanking die 凹击模L18 punched tape 穿孔帶L3 purchase ['p☜:t☞☜s] vt. 買，購買L6 push back pin 回程杆L5 pyrometer[pai'n mit☜] n. 高溫計L2 Qquality['kwaliti] n. 品質L1,3 quandrant['kw dr☜nt] n. 象限L9 quantity ['kw ntiti] n. 量，數量L17 quench[kwent☞] vt. 淬火L2 Rradial['reidi☜l] adv.放射狀的L22 ram [r✌m] n 撞錘. L17 rapid['r✌pid]adj. 迅速的L2 rapidly['r✌pidli]adv. 迅速地L1 raster['r✌st☜] n. 光柵L9raw [r :] adj. 未加工的L6 raw material 原材料L3 ream [ri:m] v 鉸大L17 reaming[ri:mi☠] n. 擴孔, 鉸孔L8 recall[ri'k :l] vt. 記起, 想起L13 recede [ri'si:d] v. 收回, 後退L20 recess [ri'ses] n. 凹槽,凹座,凹進處L4,18 redundancy[ri'd✈nd☜nsi] n. 過多L9re-entrant 凹入的L12 refer[ri'f☜:] v. 指, 涉及, 談及L1,12 reference['ref☜r☜ns] n.參照,參考L21 refresh display 刷新顯示L9 register ring 定位環L11 register['red✞st☜] v. 記錄, 顯示, 記數L2 regrind[ri:'♈aind](reground[ri:'gru:nd]) vt. 再磨研L12 relative['rel☜tiv] a. 相當的, 比較的L12 relay ['ri:lei] n. 繼電器L7 release[ri'li:s] vt. 釋放L1 relegate['rel☜geit] vt. 把··降低到L9 reliability [rilai☜'biliti] n. 可靠性L7 relief valves 安全閥L22 relief[ri'li:f] n.解除L22 relieve[ri'li:v ]vt.減輕, 解除L2 remainder[ri'meind☜] n. 剩餘物, 其餘部分L4 removal[ri'mu:vl] n. 取出L14 remove[ri'mu:v] v. 切除, 切削L4 reposition [rip☜'zi☞☜n] n.重新安排L17 represent[ repri'zent☜] v 代表,象徵L11 reputable['repjut☜bl] a. 有名的, 受尊敬的L15 reservoir['rez☜vwa: ] n.容器, 儲存器L22 resident['rezid☜nt] a. 駐存的L9 resist[ri'zist] vt.抵抗L1 resistance[ri'zist☜ns] n.阻力, 抵抗L1 resolution[ rez☜'lu:☞☜n] n. 解析度L9 respective[ri'spektiv] a.分別的,各自的L11 respond[ris'p nd] v.回應, 作出反應L9 responsibility[risp ns☜'biliti] n.責任L13 restrain[ris'trein]v.抑制L21 restrict [ris'trikt] vt 限制，限定L18 restriction[ris'trik☞☜n] n. 限制L12 retain[ri'tein] vt.保持, 保留L2,12 retaining plate 頂出固定板L16 reveal [ri'vil] vt.顯示，展現L17 reversal [ri'v☜sl] n. 反向L1,20 right-angled 成直角的L20 rigidity[ri'd✞iditi] n. 剛度L1 rod[r d] n. 杆, 棒L1,5 rotate['r☜uteit] vt.(使)旋轉L5 rough machining 粗加工L5 rough[r✈f] a. 粗略的L5,21 routine [ru:'ti:n] n. 程式L7 rubber['r✈b☜] n.橡膠L3,22 runner and gate systems 流道和澆口系統L11S128sand casting 砂型鑄造L3 satisfactorily[ s✌tis'f✌ktrili] adv. 滿意地L1saw[a :] n. 鋸子L4 scale[skeil]n. 硬殼L2 score[sk :] v. 刻劃L14 scrap[skr✌p] n.廢料, 邊角料, 切屑L2,3 screwcutting 切螺紋L4 seal[si:l] vt.密封L22 secondary storage L9 section cutting plane 剖切面L16 secure[si'kju☜] v.固定L22 secure[si'kju☜] vt.緊固,夾緊,固定L5,22 segment['se♈m☜nt] v. 分割L10sensitive['sensitiv]a.敏感的L1,7 sequence ['si:kw☜ns] n. 次序L6 sequential[si'kwen☞☜l] a.相繼的L16 seriously['si☜ri☜sli] adv.嚴重地L1 servomechanism ['s☜:v☜'mek☜nizm] n.伺服機構L7 Servomechanism Laboratoies 伺服機構實驗室L7 servomotor ['s☜:v☜m☜ut☜] n.伺服馬達L8 setter ['set☜] n 安裝者L17 set-up 機構L20 sever ['sev☜] v 切斷L17 severity [si'veriti] n. 嚴重L20 shaded[☞✌did] adj.陰影的L21 shank [☞✌☠k] n. 柄. L17 shear[☞i☜]n.剪,切L1 shot[☞t] n. 注射L12 shrink[☞ri☠k] vi. 收縮L11 side sectional view 側視圖L16 signal ['si♈nl] n.信號L8 similarity[simi'l✌riti] n.類似L15 simplicity[sim'plisiti] n. 簡單L12 single-point cutting tool 單刃刀具L5 situate['sitjueit] vt. 使位於, 使處於L11 slide [slaid] vi. 滑動, 滑落L20 slideway['slaidwei] n. 導軌L5 slot[sl t] n. 槽L4 slug[sl✈♈] n. 嵌條L12 soak[s☜uk] v. 浸, 泡, 均熱L2 software ['s ftw☪☜] n. 軟體L6 solid['s lid] n.立體, 固體L9 solidify[s☜'lidifai] vt.vi. (使)凝固, (使)固化L13 solution[s☜'lu:☞☜n] n.溶液L2sophisiticated [s☜'fistikeitid] adj.尖端的,完善的L8 sound[saund] a. 結實的, 堅固的) L1 spark erosion 火花蝕刻L10 spindle['spindl] n. 主軸L5,8 spline[splain] n.花鍵L4 split[split] n. 側向分型, 分型L12,14 spool[spu:l] n. 線軸L14 springback n.反彈L20 spring-loaded 裝彈簧的L18 sprue bush 主流道襯套L11 sprue puller 澆道拉杆L12 square[skw☪☜] v. 使成方形L4 stage [steid✞] n. 階段L16,19 standardisation[ st✌nd☜dai'zei☞☜n] n. 標準化L15 startling['sta:tli☠] a. 令人吃驚的L10 steadily['sted☜li ] adv. 穩定地L21 step-by-step 逐步L8 stickiness['stikinis] n.粘性L22 stiffness['stifnis] n. 剛度L1 stock[st k] n.毛坯, 坯料L3 storage tube display 儲存管顯示L9 storage['st :rid✞] n. 儲存器L9 straightforward[streit'f :w☜d]a.直接的L10 strain[strein] n.應變L1129strength[stre☠] n.強度L1 stress[stres] n.壓力,應力L1 stress-strain應力--應變L6 stretch[stret☞] v.伸展L1,21 strike [straik] vt. 衝擊L20 stringent['strind✞☜nt ] a.嚴厲的L22 stripper[strip☜] n. 推板L15 stroke[strouk] n. 衝程, 行程L12 structrural build-up 結構上形成的L11 sub-base 墊板L19 subject['s✈bd✞ikt] vt.使受到L21 submerge[s☜b'm☜:d✞] v.淹沒L22 subsequent ['s✈bsikwent] adj. 後來的L20 subsequently ['s✈bsikwentli] adv. 後來, 隨後L5 substantial[s☜b'st✌n☞☜l] a. 實質的L10 substitute ['s✈bstitju:t] vt. 代替,.替換L7 subtract[s☜b'tr✌kt] v.減, 減去L15 suitable['su:t☜bl] a. 合適的, 適當的L5 suitably['su:t☜bli] ad.合適地L15 sunk[s✈☠k](sink的過去分詞) v. 下沉, 下陷L11 superior[s☜'pi☜ri☜] adj.上好的L22 susceptible[s☜'sept☜bl] adj.易受影響的L7 sweep away 掃過L17 symmetrical[si'metrikl] a. 對稱的L14 synchronize ['si☠kr☜naiz] v.同步,同時發生L8Ttactile['t✌ktail] a. 觸覺的, 有觸覺的L9 tailstock['teilst k] n.尾架L5 tapered['teip☜d] a. 錐形的L12 tapping['t✌pi☠] n. 攻絲L8 technique[tek'ni:k] n. 技術L16 tempering['temp☜r☠] n.回火L2 tendency['tend☜nsi] n. 趨向, 傾向L13tensile['tensail] a.拉力的, 可拉伸的L2 拉緊的, 張緊的L1 tension ['ten☞☜n] n.拉緊,張緊L1 terminal ['t☜:m☜nl ] n. 終端機L6 terminology[t☜:mi'n l☜d✞i ] n. 術語, 用辭L11 theoretically [ i:☜'retikli ] adv.理論地L21 thereby['❆☪☜bai] ad. 因此, 從而L15 thermoplastic[' ☜:m☜u'pl✌stik] a. 熱塑性的, n. 熱塑性塑膠L3 thermoset[' ☜:m☜set] n.熱固性L12 thoroughly[' ✈r☜uli] adv.十分地, 徹底地L2 thread pitch 螺距L5 thread[ red] n. 螺紋L5 thrown up 推上L17tilt [tilt] n. 傾斜, 翹起L20 tolerance ['t l☜r☜ns] n..公差L17 tong[t ☠] n. 火鉗L2 tonnage['t✈nid✞] n.噸位, 總噸數L3tool point 刀鋒L3 tool room 工具車間L10 toolholder['tu:lh☜uld☜] n.刀夾,工具柄L5 toolmaker ['tu:l'meik☜] n 模具製造者L17 toolpost grinder 工具磨床L4 toolpost['tu:l'p☜ust] n. 刀架L4 torsional ['t :☞☜nl] a扭轉的. L1 toughness['t fnis] n. 韌性L2 trace [treis] vt.追蹤L7 tracer-controlled milling machine 仿形銑床L4 transverse[tr✌ns'v☜:s] a. 橫向的L5 tray [trei] n. 盤，盤子，蝶L19 treatment['tri:tm☜nt] n.處理L2tremendous[tri'mend☜s] a. 驚人的, 巨大的L9 trend [trend] n.趨勢L7130glossary131trigger stop 始用擋料銷 L17 tungsten['t ✈☠st ☜n] n.鎢L10turning['t ☜:ni ☠] n.車削 L4,5 twist[twist ] v.扭曲，扭轉L1 two-plate mould 雙板式注射模L12 Uultimately['✈ltimitli] adv 終於. L6undercut moulding 側向分型模 L14 undercut['✈nd ☜k ✈t] n. 側向分型 L14undercut['✈nd ☜k ✈t] n.底切L12underfeed['✈nd ☜'fi:d] a, 底部進料的 L15 undergo[✈nd ☜'♈☜u] vt.經受L1 underside['✈nd ☜said] n 下麵,下側L11undue[✈n'dju:] a.不適當的, 過度的 L4,10 uniform['ju:nif :m] a.統一的, 一致的 L12 utilize ['ju:tilaiz] v 利用 L17 Utopian[ju't ☜upi ☜n] adj.烏托邦的, 理想化的L21Vvalve[v ✌lv] n.閥L22vaporize['veip ☜raiz] vt.vi. 汽化, (使)蒸發L10variation [v ☪☜ri'ei ☞☜n] n. 變化L20various ['v ☪☜ri ☜s] a.不同的,各種的 L1,20 vector feedrate computation 向量進刀速率計算L7 vee [vi:] n. v 字形L20 velocity[vi'l siti] n.速度L1versatile['v ☜s ☜tail] a.多才多藝的,萬用的L5,8vertical['v ☜:tikl] a. 垂直的 L16 via [vai ☜] prep.經,通過 L8 vicinity[v ☜'siniti] n.附近L13 viewpoint['vju:p int] n. 觀點L4Wwander['w nd ☜] v. 偏離方向 L13 warp[w :p] v. 翹曲 L2 washer ['w ☞☜] n. 墊圈L18 wear [w ☪☜] v.磨損 L7 well line 結合線L13 whereupon [hw ☪☜r ☜'p n] adv. 於是 L19 winding ['waindi ☠] n. 繞, 卷 L8 with respect to 相對於 L1,5 withstand[wi ❆'st ✌nd] vt.經受,經得起 L1work[w ☜:k] n. 工件 L4 workstage 工序L19 wrinkle['ri ☠kl] n.皺紋vt.使皺L21 Yyield[ji:ld] v. 生產L9 Zzoom[zu:] n. 圖像電子放大L9。
模具部分常用词汇
11． 模具材质 瑞典一胜百的S136：Sweden ASSAB S136日本大同NAK80：Japanese DAIDO NAK80德国2316不锈钢：Germany 2316 Stainless Steel镁铝7075：Mg Al 7075, Al 7075 (铝Aluminum), magnalium铍铜：Beryllium Copper, berglliumP20钢材：P20 Steel2． 热流道系统韩国YUDO 热流道系统：Korea YUDO Hot Runner SystemHUSKY Hot Runner SystemMold-Masters Hot Runner System温控：Temperature Controller加热元件：Heater喷嘴：Nozzle感温线：temperature line3． 模具零部件名模具：mould, mold, tool, die型芯：core, die core型腔：cavity, impression, seats, locals成型部分：molding part模板：mould plate模架：mould frame, mould base导柱：guide pillar, guide pin, leader pin导套：guide bushing, guide push浇口：gate, sprue点浇口：pin gate, pin point直浇口：sprue gate侧浇口：side gate侧缘浇口：edge gate环形浇口：ring gate扇形浇口：fan gate潜入式浇口：submarine gate隧道式浇口：tunnel gate汽缸：cylinder淬火：quench (hardening)流痕：flow mark熔合痕：welding mark脱料板（脱模板）：stripper plate定位圈：locating ring抛光：polishing刀口：knife-edge, cutting edge切口圈：cutting ring2 水接头：water fitting冷却：cooling衬套：bushing刻字：engraving自动打飞边装置：auto-deflashing system/unit试模：test mould, mould trial热处理：heat treatment硬度：hardness表面光洁度：cleanliness of the surface喷砂：sand blasting模具寿命：mould life****模：cycle, shot旋脱：unscrewing system吊环：eye-bolt出水孔：water discharge hole水嘴：water faucet模芯：head模套：die-head流道：runner, channel推杆：pusher/ejector pin推管：ejector sleeve冲头：punch镶件：insert 又称嵌件底板：basic plate排气槽：exhaust channel, air vent汽缸：cylinder淬火：quench (hardening)流痕：flow mark回位销：return pin顶出销：knock pin毛边：galling拉料杆：sprue lock pin绝缘流道方式：insulated runner吹塑成型：blow molding注塑成型：injection molding动模：movable mould, moving half定模：stationary mould, fixed half动模座板：moving clamp plate, bottom clamping plate, bottom plate定模座板：fixed clamp plate, top clamping plate, top plate顶出板：knock-out plate斜导柱：Angle guide pillar, slanted guide pillar, angle pin, angular cam, inclined guide pillar, bevel pillar3 4． 重要注塑机参数合模力：clamping force, clamp tonnage移模行程：opening stroke, mold open stroke拉杆间距：tie bar space, space between tie bars模厚：mould height, max./min. mold height开模间距：daylight opening顶出行程：ejector stroke顶出力：ejector tonnage注射重量：injection weight (PS) 单位：g注射压力：injection pressure 单位：Mpa模板尺寸：platen dimensions5． 重要吹塑机参数吹针：blown pin ，blow needle模具大小及厚度：mould dimension and height中心距：distance center to center口模：die and pin模头：die head壁厚控制器：wall-thickness controller6． 设备平面磨床：face grinding钻床：drill press铣床：milling machine线切割机：wire cutting machine (wire EDM, Electron Discharge Machinery)数控机床：NC machine tool数控车床：Numerical Controlled Lathe车间学习：火花机：测表面平整（百分表），分中，放电。
模具常用英语词汇
die block块形模体
die body铸模座
die bush合模衬套
die button冲模母模
die clamper夹模器
die fastener模具固定用零件
die holder母模固定板
die lip模唇
die plate冲模板
die set冲压模座
direct gate直接浇口
ejector leader busher顶出导梢衬套
ejector pad顶出垫
ejector pin顶出梢
ejector plate顶出板
ejector rod顶出杆
ejector sleeve顶出衬套
ejector valve顶出阀
eye bolt环首螺栓
filling core椿入蕊
film gate薄膜形浇口
slag riser冒渣口
slide(slide core)滑块
slip joint滑配接头
spacer block间隔块
spacer ring间隔环spider模蕊支架
spindle主轴
sprue注道
sprue bushing注道衬套
sprue bushing guide注道导套
sprue lock bushing注道定位衬套
sprue puller注道拉料
spue line合模线
square key方键
square nut方螺帽
square thread方螺纹
stop collar限位套
stop pin止动梢
stop ring止动环
stopper定位停止梢
straight pin圆柱销
stripper bolt脱料螺栓
模具英文术语
根据国家标准，以下为部分塑料模具成形术语的标准翻译。
动模 Movable Mould Moving Half定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate下模座板 Lower Clamping Plate凹模固定板 Cavity-retainer Plate型芯固定板 Mould Core-retainer Plate凸模固定板 Punch-retainer Plate模套 Die Body Die Sleeve Die Blank支承板 Backing Plate Support Plate垫块 Spacer Parallel支架 Ejector Housing Mould Base Leg模头 Die Head根据国家标准，以下为部分压铸模具术语的标准翻译。
压力铸造模具 Die-Casting Die压铸模零部件定模 Fixed Die Cover Die定模座板 Fixed Clamping Plate定模套板 Bolster Fixed Die动模 Moving Die Ejector Die动模座板 Moving Clamping Plate直流道 Sprue横流道 Runner内浇口 Gate模具分类Injection Mold 注塑模Plastic Rubber Mould 塑胶模Rubber Molding 橡胶成形Hot Chamber Die Casting 热室压铸Sand Mold Casting 砂模铸造Extrusion Mold 挤出模Multi-Cavity Mold 多模穴模具Stack Mold, Stack Injection Mould 叠层模Plaster Mold 石膏模Three Plates Mold 三板模Plain Die 简易模Pierce Die 冲孔模Forming Die 成型模Progressive Die 连续模Gang Dies 复合模Shearing Die 剪边模Cavity Die 型腔模Riveting Die 铆合模Compression Molding 压缩成型Flash Mold 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Mould Cavity 型腔母模Mold Core 模芯公模Large Die Mold 大型模具Precise Die Mold 精密模具Complex Die Mold 复杂模具Foaming Mould 发泡模具Metal Die 金属模具Plastic Mold 塑料模具Press Tool Stamping Die Punch Die 冲压模具Extrusion Die 挤压模具Graphite Die 石墨模具流道浇口部分Runner System 浇道系统Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆Runner Design 流道设计Main Runner 主流道Secondary Runner 次流道Mould Gate Design 浇口设计Submarine Gate 潜伏浇口Tunnel Gate 隧道式浇口Pinpoint Gate 点浇口Fan Gate 扇形浇口Side Gate 侧浇口Edge Gate 侧缘浇口Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口Dish Gate 盘形浇口Diaphragm Gate 隔膜浇口Ring Gate 环形浇口Runnerless 无浇道Sprueless 无射料管方式Long Nozzle 延长喷嘴方式Sprue 浇口，溶渣Insulated Runner Hot Runner 热浇道Runner Plat 浇道模块Valve Gate阀门浇口Slag Well 冷料井Cold Slag 冷料渣Sprue Gate 射料浇口，直浇口Nozzle 射嘴Sprue Lock Pin 料头钩销（拉料杆）注塑缺陷Flash 飞边Warpage 翘曲Air Trap 积风Blush 发赤Flow Line 流痕Splay 银纹Short Shot 短射Sink Mark 缩痕Streak 条纹Void 缩孔Weld Line 熔接线Gas Mark 烧焦Cold Slug 冷斑Delamination 起皮Burr 毛刺Flaw Scratch 刮伤Gloss 光泽Glazing 光滑Surface Check 表面裂痕Hesitation 迟滞注塑工艺Molding Conditions 成型条件Drying 烘干Barrel Temperature 料筒温度Melt Temperature 熔化温度Mold Temperature 模具温度Injection Pressure 注塑压力Back Pressure 背压Injection Speed 注塑速度Screw Speed 螺杆转速Tensile Strength 抗拉强度Tensile Elongation 延伸率Flexural Modulus 弯曲模数Flexural Strength 抗弯强度Shrinkage 收缩率Regrind Usage 次料使用Moulding 模塑机械设备Lathe 车床Planer 刨床Miller Milling Machine 铣床Grinder 磨床Driller 钻床Linear Cutting 线切割Electrical Sparkle 电火花Welder 电焊机Punching Machine 冲床Robot 机械手Common Equipment 常用设备EDM Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Cylindrical Grinding Machine 外圆磨床Die Spotting Machine 合模机Engraving Machine 雕刻机Engraving E.D.M 雕模放置加工机Form Grinding Machine 成形磨床, Graphite Machine 石墨加工机Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床模具零件Top Plate 上托板（顶板）Top Block 上垫脚Punch Set 上模座Punch Pad 上垫板Punch Holder 上夹板Stripper Pad 脱料背板Up Stripper 上脱料板Male Die 公模（凸模）Feature Die 公母模Female Die 母模（凹模）Upper Mold Plate 上模板Lower Mold Plate 下模板Die Pad 下垫板Die Holder 下夹板Die Set 下模座Bottom Block 下垫脚Bottom Plate下托板（底板）Stripping Plate 内外打（脱料板）Outer Stripper 外脱料板Inner Stripper 内脱料板Lower Stripper 下脱料板Inner Guiding Post 内导柱Inner Hexagon Screw 内六角螺钉Dowel Pin 固定销Mould Coil Spring 模具弹簧Lifter Pin 顶料销Isoheight Sleeve 等高套筒Pin 销Lifter Guide Pin 浮升导料销Guide Pin 导正销Wire Spring 圆线弹簧Outer Guiding Post 外导柱Stop Screw 止付螺丝Located Pin 定位销Outer Bush 外导套Punch 冲头Insert 入块（嵌入件）Deburring Punch 压毛边冲子Groove Punch 压线冲子Stamped Punch 字模冲子Round Punch 圆冲子Special Shape Punch 异形冲子Bending Block 折刀Roller 滚轴Baffle Plate 挡块Located Block 定位块Supporting Block for Location 定位支承块Air Cushion Plate 气垫板Air-Cushion Eject-rod 气垫顶杆Trimming Punch 切边冲子Stiffening Rib Punch Stinger 加强筋冲子Ribbon Punch 压筋冲子Reel-stretch Punch 卷圆压平冲子Guide Plate 定位板Sliding Block 滑块Sliding Dowel Block 滑块固定块Active Plate 活动板Lower Sliding Plate 下滑块板Upper Holder Block 上压块Upper Mid Plate 上中间板Spring Box 弹簧箱Spring-Box Eject-rod 弹簧箱顶杆Spring-Box Eject-Plate 弹簧箱顶板Bushing Block Liner Bushing 衬套Cover Plate 盖板Guide Pad 导料块模具技术用语各种常用模具成形方式Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow Blow Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Close Mold 合模Demould 脱模脱模剂Mould Unloading 开模Eject 顶出Tool Change Retooling Die Changing 换模Mould Clamping 锁模各式模具分类用语Bismuth Mold 铋铸模Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模法Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Cold Bending Die 双折冷弯模具Extrusion Die 挤出模Stack Mold, Stack Injection Mould 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具原型模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模切缝模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具<, /SPAN> Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模模具厂常用之标准零配件Air Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流档板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting lug 铸耳Cavity 模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Nippler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Insert 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针起模杆Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头锤击强化冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道拉料浇道推出杆注道残料顶销Spew Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Limit Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming Pouring 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板模具常用之工作机械3D Coordinate Measurement 三次元量床Boring Machine 搪孔机CNC Milling Machine CNC铣床Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Copy Lathe 仿形车床Copy Milling Machine 仿形铣床Copy Shaping Machine 仿形刨床Cylindrical Grinding Machine 外圆磨床Die Spotting Machine 合模机Drilling Machine 钻孔机Engraving Machine 雕刻机Engraving E.D.M 雕模放置加工机Form Grinding Machine 成形磨床Graphite Machine 石墨加工机Horizontal Boring Machine 卧式搪孔机Horizontal Machine Center 卧式加工制造中心Internal Cylindrical Machine 内圆磨床Jig Boring Machine 冶具搪孔机Jig Grinding Machine 冶具磨床Lap Machine 研磨机Machine Center 加工制造中心Multi Model Miller 靠磨铣床NC Drilling Machine NC钻床NC Grinding Machine NC磨床NC Lathe NC车床NC Programming System NC程式制作系统Planer 龙门刨床Profile Grinding Machine 投影磨床Projection Grinder 投影磨床Radial Drilling Machine 旋臂钻床Shaper 牛头刨床Surface Grinder 平面磨床Try Machine 试模机Turret Lathe 转塔车床Universal Tool Grinding Machine 万能工具磨床Vertical Machine Center 立式加工制造中心Wire E.D.M 线割放电加工机入水 Gate进入位 Gate Location水口形式 Gate Type大水口 Edge Gate细水口 Pin-point Gate水口大小 Gate Size转水口 Switching Runner Gate唧嘴口径 Sprue Diameter流道 Mold Runner热流道 Hot Runner Hot Manifold温度控制器温控器 Thermostat Thermoregulators Temperature Controller热嘴冷流道 Hot Sprue Cold Runner唧嘴直流 Direct Sprue Gate圆形流道 Round Full Half Runner流道电脑分析 Mold Flow Analysis流道平衡 Runner Balance热嘴 Hot Sprue热流道板 Hot Manifold发热管 Cartridge Heater探针 Thermocouples插头 Connector Plug插座 Connector Socket密封封料 Seal运水 Water Line喉塞 Line Plug Throat Taps喉管 Tube塑胶管 Plastic Tube快速接头 Jiffy Quick Connector Quick Disconnect Coupling 模具零件 Mold Components三板模 3-Plate Mold二板模 2-Plate Mold边钉导边 Leader Pin Guide Pin边司导套 Bushing Guide Bushing中托司 Shoulder Guide Bushing中托边 Guide Pin顶针板 Ejector Retainner Plate托板 Support Plate螺丝 Screw管钉 Dowel Pin开模槽 Ply Bar Scot内模管位 Core Cavity inter-Lock顶针 Ejector Pin司筒 Ejector Sleeve司筒针 Ejector Pin推板 Eject Plate Push Plate Stripper Plate缩呵 Movable Core Return Core Puller扣机（尼龙拉勾） Nylon Latch Lock斜顶 Lifter模胚（架） Mold Base上内模 Cavity Insert下内模 Core Insert行位（滑块） Slide镶件 Insert压座 Wedge耐磨板油板 Wedge Wear Plate压条 Plate撑头 Support Pillar唧嘴 Sprue Bushing挡板 Stop Plate定位圈 Locating Ring锁扣 Latch扣机 Parting Lock Set推杆 Push Bar栓打螺丝 S.H.S.B顶板 Ejector Plate活动臂 Lever Arm分流锥 Sprue Spreader分流板 Spreader Plate水口司 Bush垃圾钉 Stop Pin隔片 Buffle弹弓柱 Spring Rod弹弓 Die Spring中托司 Ejector Guide Bush中托边 Ejector Guide Pin镶针 Pin销子 Dowel Pin波子弹弓 Ball catch喉塞 Pipe Plug锁模块 Lock Plate斜顶 Angle from Pin斜顶杆 Angle Ejector Rod尼龙拉勾 Parting Locks活动臂 Lever Arm复位键提前回杆 Early Return Bar气阀 Valves斜导边 Angle Pin术语 Terms承压平面平衡 Parting Surface Support Balance模排气 Parting Line Venting回针碰料位 Return Pin and Cavity Interference顶针碰运水 Water Line Interferes with Ejector Pin 料位出上下模 Part from Cavith （Core） Side不准用镶件 Do Not Use （Core Cavity） Insert用铍铜做镶件 Use Beryllium Copper Insert初步模图设计 Preliminary Mold Design正式模图设计 Final Mold Design弹弓压缩量 Spring Compressed length稳定性好 Good Stability Stable强度不够 Insufficient Rigidity均匀冷却 Even Cooling扣模 Sticking热膨胀 Thermal Expansion公差 Tolerance铜公（电极） Copper ElectrodeAir Vent Valve 通气阀Anchor Pin 锚梢Angular Pin 角梢Baffle 调节阻板Angular Pin 倾斜梢Baffle Plate 折流挡板Ball Button 球塞套Ball Plunger 定位球塞Ball Slider 球塞滑块Binder Plate 压板Blank Holder 防皱压板Blanking Die 落料冲头Bolster 上下模板Bottom Board 浇注底板Bolster 垫板Bottom Plate 下固定板Bracket 托架Bumper Block 缓冲块Buster 堵口Casting Ladle 浇注包Casting Lug 铸耳Cavity 模腔模穴（模仁）Cavity Retainer Plate 模穴托板Center Pin 中心梢Clamping Block 锁定块Coil Spring 螺旋弹簧Cold Punched Nut 冷冲螺母Cooling Spiral 螺旋冷却栓Core 心型Core Pin 心型梢Cotter 开口梢Cross 十字接头Cushion Pin 缓冲梢Diaphragm Gate 盘形浇口Die Approach 模头料道Die Bed 型底Die Block 块形模体Die Body 模体Die Body 铸模座Die Bush 合模衬套Die Button 冲模母模Die Clamper 夹模器Die Fastener 模具固定用零件Die Holder 母模固定板Die Lip 模唇Die Plate 冲模板Die Set 冲压模座Direct Gate 直接浇口Dog Chuck 爪牙夹头Dowel 定位梢Dowel Hole 导套孔Dowel Pin 合模梢Dozzle 辅助浇口Dowel Pin 定位梢Draft 拔模锥度Draw Bead 张力调整杆Drive Bearing 传动轴承Ejection Pad 顶出衬垫Ejector 脱模器Ejector Guide Pin 顶出导梢Ejector Leader Bush 顶出导梢衬套Ejector Pad 顶出垫Ejector Pin 顶出梢Ejector Plate 顶出板Ejector Rod 顶出杆Ejector Sleeve 顶出衬套Ejector Valve 顶出阀Eye Bolt 环首螺栓Filling Core 填充型芯椿入蕊Film Gate 薄膜形浇口Finger Pin 指形梢Finish Machined Plate 角形模板Finish Machined Round Plate 圆形模板Fixed Bolster Plate 固定侧模板Flanged Pin 带凸缘针Flash Gate 毛边形浇口Flask 上箱Floating Punch 浮动冲头Gate 浇口Gate Land 浇口面Gib 凹形拉紧楔Goose Neck 鹅颈管Guide Bushing 引导衬套Guide Pin 导梢Guide Post 引导柱Guide Plate 导板Guide Rail 导轨Head Punch 顶头冲孔Headless Punch 直柄冲头Heavily Tapered Solid 整体模蕊盒Hose Joint Pipe Coupler 管接头Impact Damper 缓冲器Injection Ram 压射柱塞Inlay Bush 嵌入衬套Inner Plunger 内柱塞Inner Punch 内冲头Inserts 嵌件Insert Pin 嵌件梢King Pin 转向梢King Pin Bush 主梢衬套Knockout Bar 脱模杵Land 合模平坦面Land Area 合模面Leader Bush 导梢衬套Lifting Pin 起模顶针Lining 内衬Locating Center Punch 定位中心冲头Locating Pilot Pin 定位导梢Locating Ring 定位环Lock Block 压块Locking Block 定位块Locking Plate 定位板Loose Bush 活动衬套Making Die 打印冲子Manifold Block 歧管档块Master Plate 靠模样板Match Plate 分型板Mold Base 塑胶模座Mold Clamp 铸模紧固夹Mold Platen 模用板Moving Bolster 换模保持装置Moving Bolster Plate 可动侧模板One Piece Casting 整体铸件Parallel Block 平行垫块Parting Line 分模线Parting Lock Set 合模定位器Pass Guide 穴型导板Peened Head Punch 镶入式冲头钻杆凸模Pilot Pin 定位销导向销子Pin Gate 针尖浇口Plate 衬板Pre Extrusion Punch 顶挤冲头Punch 冲头Puncher 推杆Pusher Pin 衬套梢Rack 机架Rapping Rod 起模杆Re-entrant Mold 凹入模Retainer Pin 嵌件梢Retainer Plate 托料板Return Pin 回位梢Riding Stripper 浮动脱模器Ring Gate 环型浇口Roller 滚筒Runner 流道Runner Ejector Set 流道顶出器Runner Lock Pin 流道拉梢Screw Plug 头塞Set Screw 固定螺丝Shedder 脱模装置Shim 分隔片Shoe 模座之上下模板Shoot 流道Shoulder Bolt 肩部螺丝Skeleton Frameworks 骨架Slag Riser 冒渣口Slide（Slide Core）滑块Slip Joint 滑配接头Spacer Block 间隔块Spacer Ring 间隔环Spider 模蕊支架Spindle 主轴Sprue 注道Sprue Bushing 注道衬套Sprue Bushing Guide 注道导套Sprue Lock Bushing 注道定位衬套Sprue Puller 注道残料顶销浇道推出杆Sprue Line 合模线Square Key 方键Square Nut 方螺帽Square Thread 方螺纹Stop Collar 限位套Stop Pin 止动梢Stop Ring 止动环Stopper 定位停止梢Straight Pin 圆柱销Stripper Bolt 脱料螺栓Stripper Bushing 脱模衬套Stripper Plate 剥料板Stroke End Block 行程止梢Submarine Gate 潜入式浇口Support Pillar 支撑支柱顶出支柱Support Pin 支撑梢Supporting Plate 托板Sweep Template 造模刮板Tab Gate 辅助浇口Taper Key 推拔键Taper Pin 拔锥梢锥形梢Teeming 浇注Three Start Screw 三条螺纹Thrust Pin 推力销Tie Bar 拉杵Tunnel Gate 隧道形浇口Vent 通气孔Wortle Plate 拉丝模板Pierce 冲孔Forming 成型（抽凸冲凸）Draw Hole 抽孔Bending 折弯Trim 切边Emboss 凸点Dome 凸圆Semi-Shearing 半剪Stamp Mark 冲记号Deburr or Coin 压毛边Punch Riveting 冲压铆合Side Stretch 侧冲压平Reel Stretch 卷圆压平Groove 压线Blanking 下料Stamp Letter 冲字（料号）Shearing 剪断Tick-Mark Nearside 正面压印Tick-Mark Farside 反面压印Extension Drawing 展开图procedure Drawing 工程图Die Structure Drawing 模具结构图Material 材质Material Thickness 料片厚度Factor 系数Upward 向上Downward 向下Press Specification 冲床规格Die Height Range 适用模高Die Height 闭模高度Burr 毛边Gap 间隙Weight 重量Total Weight 总重量Punch Weight 上模重量Compression Molding 压缩成型Flash Mold 溢流式模具Extrusion Mold 挤压式模具Split Mold 分割式模具Cavity 型腔母模Mold Core 模芯公模Taper 锥拔Leather Cloak 仿皮革Shiver 饰纹Flow Mark 流痕Welding Mark 溶合痕Post Screw Insert 螺纹套筒埋值Self Tapping Screw 自攻螺丝Striper Plate 脱料板Piston 活塞Cylinder 汽缸套Chip 细碎物Handle Mold 手持式模具Encapsulation Molding 低压封装成型Two Plate 两极式（模具）Well Type 蓄料井Insulated Runner 绝缘浇道方式Hot Runner 热浇道Runner Plat 浇道模块Valve Gate 阀门浇口Band Heater 环带状的电热器Spindle 阀针Spear Head 刨尖头Slag Well 冷料井Cold Slag 冷料渣Air Vent 排气道Welding Line 熔合痕Eject Pin 顶出针Knock Pin 顶出销Return Pin 回位销反顶针Sleeve 套筒Stripper Plate 脱料板Insert Core 放置入子Runner Stripper Plate 浇道脱料板Guide Pin 导销Eject Rod （Bar）（成型机）顶业捧Subzero 深冷处理Three Plate 三极式模具Runner System 浇道系统Stress Crack 应力电裂Orientation 定向Sprue Gate 射料浇口，直浇口Nozzle 射嘴Sprue Lock Pin 料头钩销（拉料杆）Slag Well 冷料井Side Gate 侧浇口Edge Gate 侧缘浇口Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口Fan Gate 扇形浇口Dish Gate 因盘形浇口Diaphragm Gate 隔膜浇口Ring Gate 环形浇口Submarine Gate 潜入式浇口Tunnel Gate 隧道式浇口Pin Gate 针点浇口Runnerless 无浇道Sprueless 无射料管方式Long Nozzle 延长喷嘴方式Sprue 浇口溶渣Landed Plunger Mold 有肩柱塞式模具Burnishing Die 挤光模Landed Positive Mold 有肩全压式模具Button Die 镶入式圆形凹模Loading Shoe Mold 料套式模具Center-Gated Mold 中心浇口式模具Loose Detail Mold 活零件模具Chill Mold 冷硬用铸模Loose Mold 活动式模具Cold Hobbing 冷挤压制模Louvering Die 百叶窗冲切模Composite Dies 复合模具Manifold Die 分歧管模具Counter Punch 反凸模Modular Mold 组合式模具Double Stack Mold 双层模具Multi-Cavity Mold 多模穴模具Electroformed Mold 电铸成形模Multi-Gate Mold 复式浇口模具Expander Die 扩径模Offset Bending Die 双折冷弯模具偏移弯曲模Extrusion Die 挤出模Palletizing Die 叠层模Family Mold 反套制品模具Plaster Mold 石膏模Blank Through Dies 漏件式落料模Porous Mold 通气性模具Duplicated Cavity Plate 复板模Positive Mold 全压式模具Fantail Die 扇尾形模具Pressure Die 压紧模Fishtail Die 鱼尾形模具Profile Die 轮廓模Flash Mold 溢料式模具Progressive Die 顺序模Gypsum Mold 石膏铸模Portable Mold 手提式模具Hot-Runner Mold 热流道模具Prototype Mold 雏形试验模具Ingot Mold 钢锭模Punching Die 落料模Lancing Die 切口模Raising（Embossing）压花起伏成形Re-entrant Mold 倒角式模具Sectional Die 拼合模Runnerless Injection Mold 无流道冷料模具Sectional Die 对合模具Segment Mold 组合模Semi-Positive Mold 半全压式模具Shaper 定型模套Single Cavity Mold 单腔模具Solid Forging Die 整体锻模Split Forging Die 拼合锻模Split Mold 双并式模具Sprueless Mold 无注道残料模具Squeezing Die 挤压模Stretch Form Die 拉伸成形模Sweeping Mold 平刮铸模Swing Die 振动模具Three Plates Mold 三片式模具Trimming Die 切边模Unit Mold 单元式模具Universal Mold 通用模具Unscrewing Mold 退扣式模具Yoke Type Die 轭型模Accurate Die Casting 精密压铸Powder Forming 粉末成形Calendaring Molding 压延成形Powder Metal Forging 粉末锻造Cold Chamber Die Casting 冷式压铸Precision Forging 精密锻造Cold Forging 冷锻Press Forging 冲锻Compacting Molding 粉末压出成形Rocking Die Forging 摇动锻造Compound Molding 复合成形Rotary Forging 回转锻造Compression Molding 压缩成形Rotational Molding 离心成形Dip Mold 浸渍成形Rubber Molding 橡胶成形Encapsulation Molding 注入成形Sand Mold Casting 砂模铸造Extrusion Molding 挤出成形Shell Casting 壳模铸造Foam Forming 发泡成形Sinter Forging 烧结锻造Forging Roll 轧锻Six Sides Forging 六面锻造Gravity Casting 重力铸造Slush Molding 凝塑成形Hollow（Blow） Molding 中空（吹出）成形Squeeze Casting 高压铸造Hot Chamber Die Casting 热室压铸Swaging 挤锻Hot Forging 热锻Transfer Molding 转送成形Injection Molding 射出成形Warm Forging 温锻Investment Casting 精密铸造Matched Die Method 对模成形法Laminating Method 被覆淋膜成形Low Pressure Casting 低压铸造Lost Wax Casting 脱蜡铸造Matched Mould Thermal Forming 对模热成形模Barreling 滚光加工Belling 压凸加工Bending 弯曲加工Blanking 下料加工Bulging 撑压加工Burring 冲缘加工Cam Die Bending 凸轮弯曲加工Caulking 压合加工Coining 压印加工Compressing 压缩加工Compression Bending 押弯曲加工Crowning 凸面加工Curl Bending 卷边弯曲加工Curling 卷曲加工Cutting 切削加工Dinking 切断蕊骨Double Shearing 叠板裁断Drawing 引伸加工Drawing with Ironing 抽引光滑加工Embossing 浮花压制加工Extrusion 挤制加工Filing 锉削加工Fine Blanking 精密下料加工Finish Blanking 光制下料加工Finishing 精整加工Flanging 凸缘加工Folding 折边弯曲加工Folding 折叠加工Forming 成形加工Impact Extrusion 冲击挤压加工Indenting 压痕加工Ironing 引缩加工Knurling 滚花Lock Seaming 固定接合Louvering 百叶窗板加工MarKing 刻印加工Necking 颈缩加工Notching 冲口加工Parting 分断加工Piercing 冲孔加工Progressive Bending 连续弯曲加工Progressive Blanking 连续下料加工Progressive Drawing 连续引伸加工Progressive Forming 连续成形加工Reaming 铰孔加工Restriking 二次精冲加工矫形锻压Riveting 铆接加工Roll Bending 滚筒弯曲加工Roll Finishing 滚压加工Rolling 压延加工Roughing 粗加工Scrapless Machining 无废料加工Seaming 折弯重叠加工Shaving 缺口修整加工Shearing 切断加工Sizing 精压加工矫正加工Slitting 割缝加工Spinning 卷边旋接Staking 铆固Stamping 锻压加工Swaging 挤锻压加工Trimming 整缘加工Upsetting 锻粗加工顶锻镦粗Wiring 抽线加工Aberration 色差Atomization 雾化Bank Mark 料垄迹印Bite 咬入Blacking Hole 涂料孔（铸疵）Blacking Scab 涂料疤Blister 起泡Blooming 起霜Blow Hole 破孔Blushing 泛白Body Wrinkle 侧壁皱纹Breaking-in 冒口带肉Bubble 膜泡Burn Mark 糊斑Flash Burr 毛边Camber Warpage 翘曲Cell 气泡Center Buckle 表面中部波皱Check 细裂痕Checking 龟裂Chipping 修整表面缺陷Clamp-off 铸件凹痕Collapse 塌陷Color Mottle 色斑Corrosion 腐蚀Crackle 裂痕裂纹Crazing 碎裂Crazing 龟裂Distortion Deformation 变形Edge 切边碎片Edge Crack 裂边Fading 退色Filler Speak 填充料斑Fissure 裂纹Flange Wrinkle 凸缘起皱Flaw 刮伤Flow Mark 流痕Galling 毛边Glazing 光滑Gloss 光泽Grease Pits 污斑Grinding Defect 磨痕Haircrack 发裂Haze 雾度Incrustation 水锈Indentation 压痕Internal Porosity 内部气孔Mismatch 偏模Mottle 斑点Necking 缩颈Nick 割痕Orange peel 橘皮状表面缺陷Overflow 溢流Peeling 剥离Pit 坑Pitting Corrosion 点状腐蚀Plate Mark 模板印痕Pock 麻点Pock Mark 痘斑Resin Streak 树脂流纹Resin Wear 树脂脱落Riding 凹陷Sagging 松垂Saponification 皂化Scar 疤痕Scrap 废料Scrap Jam 废料阻塞Scratch 刮伤划痕Scuffing 深冲表面划伤Seam 裂痕Shock Line 模口挤痕Short Shot 充填不足Shrinkage Pool 凹孔Sink Mark 凹痕Skin Inclusion 表皮折叠Straightening 矫直Streak 条状痕Surface Check 表面裂痕Surface Roughening 橘皮状表皮皱折Surging 波动Sweat Out 冒汗Torsion Distortion 扭曲Warpage 翘曲Waviness 波痕Webbing 熔塌Weld Mark 焊痕Whitening 白化Wrinkle 皱纹Gas Aassisted Technology 气辅Bottle Cap Mold 瓶盖模具。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
零件中文名称
零件英文名称
模座部分
母模固定板
TOP CHAMPING PLATE`
母模板
CAVITY PLATE
公模板
CORE PLATE
上顶板
EJECTOR RET PLATE
CLOCK
公模固定板
BUTTOM CLAMPING PLATE
导梢（三板模）
LEADER PIN
导套（三板模）
LEADER BUSHING
导梢（二板模）
GUIDE PIN
导套（二板模）
GUIDE BUSHING
顶板导梢
EJ GUIDE PIN
顶板导套
EJ GUIDE BUSHING
零件中文名称
零件英文名称
非模座部分
母模心型
CAVITY INSERT
公模仁
CORE INSERT
斜柱
ANGLE PILLAR
T型块
T BLOCK
斜梢
LEAFTER
斜梢座
LEAFTER SET
顶出梢
EJECTOR PIN
扁平顶出梢
RECTANGULAR EJECTOR PIN
双层顶出梢
DOUBLE EJECTOR PIN
顶出套筒
SLEEVE
双层顶出套筒
DOUBLE SLEEVE
抓料梢
SPRUE PULLER PIN
强制回位拉杆
RETURN ROD
停止梢
STOP PIN
型梢
CORE PIN
定位梢
DOWELS PIN
定位管
DOWELS TUBULAR
拉杆
PULL ROD
注口衬套
SPRUE BUSHING
固定环
LOCATING RING
弹簧
SPRING
支撑柱
SUPPORT PILLAR
水道塞子
COOLANT PLUG
滑块
SLIDE
滑块心型
SLIDE CORE
耐磨板
WEAR PLATE
滑块压板
SLIDE WEDGE
滑块束块
SLIDE BLOCK
斜磨梢
ANGLE PIN
1定位束块
TAPER BLOCK SET
扣板
RELEASE BAR
松离板
SPAECR
开模止板
STOP PLATE
成品顶块
STRIPPER BLOCK
母模固定板
CAVITY SUPPORT PLATE
公模垫板
BACK PLATE
胶道剥板
RUNNER STRIPPER
成品脱板
STRIPPER
上流道板
TOP RUNNER PLATE
胶道脚板
SUPPORT PLATE
电热板
HEATER PLATE
隔热板
HIGH TEMP INSULATOR SHEET
水管
WATER CONNECTION
挡水板
PLUG BAFFLES
喷水管
CASCADE WATER
快速接头
JIPPY-TILE SOCKETS
冷却棒
THEKMAL PIN
水管无头螺丝
WATER BASS PRESSURE PLUGS