模具专业英语词汇
模具专业术语英语
模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。
模具专业英语词汇
模具专业英语一：浇口：gate进胶位置：gate location胶口形式：gate type大水口：edge gate细水口：pin-point gate针点浇口：pin gate Φ0.8~1.0mm潜入式浇口：subarine gate隧道式浇口：tunnel gate侧浇口：side gate浇口大小：gate size喷嘴直径：sprue diameter定位圈：locating ring阀针：spindle喷嘴：nozzle加长喷嘴：long nozzle二、流道: runner 浇道系统：runner system 热流道：hot runner, hot manifold热喷嘴冷流道: hot sprue cold runner直胶口: direct sprue gate圆形流道：round(full/half runner流道分析：mold flow analysis流道平衡: runner balance热流道板：hot manifold发热管：cartridge heater插头：connector plug插座：connector socket密封/封料：seal冷料井：slag well冷料渣：cold slag排气道：air vent侧浇口：side gate扇形浇口：fan gate蓄料井：well type三、水路：water line堵头：line plug水管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 隔片：buffle四、模具零件：mold components模板: die plate, front board三板模：3-plate mold二板模：2-plate mold型控母模：cavity模心公模：core定位销：guide pin /location pin衬套/导套：bushing/guide bushing轴肩导套：shoulder guide bushing顶针板：ejector retainner plate托板：support plate螺丝：screw拉料杆：runner lock pin精定位：parting block导柱: guide post导套：guide bush回程杆：return pin外导套: outer bush斜导柱：regular pin顶针：ejector pin /lifting pin顶出销：knock pin套筒：ejector sleeve套筒芯子：ejector pin斜顶：lifter模胚（架）：mold base型腔镶块：cavity insert型芯镶块：core insert滑块：slide /sliding block镶件：insert斜楔：wedge耐磨板/油板：wedge wear plate。
模具专业英语词汇
入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：spray diameter流道: runner热流道：hot runner, hot manifold 热嘴冷流道: hot spray/cold runner唧嘴直流: direct spray gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot spray热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug 模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar slot模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin 模具专业英语推板：stripper plate缩呵：movable core, return core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上模：cavity insert下模：core insert行位（滑块）： slide镶件：insert压座/斜楔：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.Binjection nozzle 射出喷嘴顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability, stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolerance铜公(电极)：copper electrodebrasive grinding 强力磨削abrasive 磨料的,研磨的absence 不在，缺席accessory 附件accommodate 适应accordingly 因此,从而,相应地accuracy 精度,准确性actuate 开动(机器),驱动adequate 足够的adhesive 粘合剂adjacent 邻近的adopt 采用advance 进步advisable 可取的agitate 摇动a large extent 很大程度algorithm 算法align 定位，调准alignment 校直all-too-frequent 频繁allowance 容差,余量alternate 交替,轮流alternatively 选择,也许aluminium 铝ample 充足的analysis 分析ancillary 补助的,副的angular 有角的annealing 退火aperture 孔applied loads 作用力appropriate 适当的arc 弧,弓形arise 出现,发生arrange 安排article 制品,产品ascertain 确定,查明assemble 组装attitude 态度auxiliary 辅助的avoid 避免axis 轴axle 轮轴,车轴alternative 替换物backup 备份batch 一批bearing 轴承,支座bed 床身behavior 性能bench-work 钳工工作bend 弯曲beneath 在•••下bin 仓，料架blank 坯料blank 冲裁,落料blanking 落料模blast 一阵（风）blemish 缺点,污点bolster 模座,垫板boring 镗削,镗孔bracket 支架brass 黄铜break down 破坏breakage 破坏brine 盐水brittle 易碎的buffer 缓冲器built-in 装的bulging 凸肚burr 毛刺bush 衬套by far •••得多,最by means of 借助于boost 推进cabinet 橱柜call upon 要求carbide 碳化物carburzing 渗碳carriage 拖板,大拖板carry along 一起带走carry down over 从•••上取下carry out 完成case hardening 表面硬化case 壳,套cast steel 铸钢casting 铸造,铸件category 种类caution 警告，警示cavity and core plates 凹模和凸模板cavity 型腔,腔,洞centre-drilling 中心孔ceramic 瓷制品chain doted line 点划线channel 通道,信道characteristic 特性check 核算chip 切屑,铁屑chuck 卡盘chute 斜道circa 大约circlip (开口)簧环circuit 回路,环路circulate (使)循环clamp 夹紧clamp 压板clay 泥土clearance 间隙clip 切断，夹住cold hobbing 冷挤压cold slug well 冷料井collapse 崩塌,瓦解collapsible 可分解的combination 组合commence 开始,着手commence 开始commercial 商业的competitive 竞争的complementary 互补的complexity 复杂性complication 复杂化compression 压缩comprise 包含compromise 妥协,折衷concern with 关于concise 简明的,简练的confront 使面临connector 连接口,接头consequent 随之发生的,必然的console 控制台consume 消耗,占用consummate 使完善container 容器contingent 可能发生的CPU (central processing unit) 中央处理器conventional 常规的converge 集中于一点conversant 熟悉的conversion 换算,转换conveyer 运送装置coolant 冷却液coordinate (使)协调copy machine 仿形(加工)机床core 型芯,核心corresponding 相应的counteract 反作用,抵抗couple with 伴随contour 轮廓crack （使）破裂，裂纹critical 临界的cross-hatching 剖面线cross-section drawn 剖面图cross-slide 横向滑板CRT (cathoder-ray tube) 阴极射线管crush 压碎cryogenic 低温学的crystal 结晶状的cubic 立方的,立方体的cup (使)成杯状,引伸curable 可矫正的curvature 弧线curve 使弯曲cutter bit 刀头,刀片cyanide 氰化物complicated 复杂的dash 破折号daylight 板距decline 下落,下降,减少deform (使)变形demonstrate 证明depict 描述deposite 放置depression 凹穴descend 下降desirable 合适的detail 细节，详情deterioration 退化,恶化determine 决定diagrammmatic 图解的，图表的dictate 支配die 模具,冲模,凹模dielectric 电介质die-set 模架digital 数字式数字dimensional 尺寸的,空间的discharge 放电,卸下,排出discharge 卸下discrete 离散的,分立的dislodge 拉出,取出dissolution 结束distinct 不同的，显著的distort 扭曲distort (使)变形,扭曲distributed system 分布式系统dowel 销子dramaticlly 显著地drastic 激烈的draughting 绘图draughtsman 起草人drawing 制图drill press 钻床drum 鼓轮dual 双的，双重的ductility 延展性dynamic 动力的edge 边缘e.g.(exempli gratia) [拉]例如ejector 排出器ejector plate 顶出板ejector rob 顶杆elasticity 弹性electric dicharge machining 电火花加工electrode 电极electro-deposition 电铸elementary 基本的eliminate 消除,除去elongate (使)伸长,延长emerge 形成,显现emphasise 强调endeavour 尽力engagement 约束,接合enhance 提高,增强ensure 确保，保证erase 抹去,擦掉evaluation 评价,估价eventually 终于evolution 进展excecution 执行,完成execute 执行electrochemical machining 电化学加工exerte 施加experience 经验explosive 爆炸(性)的extend 伸展external 外部的extract 拔出extreme 极端extremely 非常地extremity 极端extrusion 挤压,挤出envisage 设想Fahrenheit 华氏温度fabricate 制作,制造flat-panel technology 平面(显示)技术facility 设备facing 端面车削fall within 属于,适合于fan 风扇far from 毫不,一点不,远非fatigue 疲劳feasible 可行的feature 特色,特征feed 进给feedback 反馈female 阴的,凹形的ferrule 套管file system 文件系统fitter 装配工,钳工fix 使固定,安装fixed half and moving half 定模和动模facilitate 帮助flexibility 适应性,柔性flexible 柔韧的flow mark 流动斑点follow-on tool 连续模foregoing 在前的,前面的foretell 预测,预示,预言forge 锻造forming 成型four screen quadrants 四屏幕象限fracture 破裂free from 免于gap 裂口,间隙gearbox 齿轮箱govern 统治,支配,管理grain 纹理graphic 图解的grasp 抓住grid 格子,网格grind 磨,磨削,研磨grinding 磨光,磨削grinding machine 磨床gripper 抓爪,夹具groove 凹槽guide bush 导套guide pillar 导柱guide pillars and bushes 导柱和导套handset 听筒hardness 硬度hardware 硬件headstock 床头箱,主轴箱hexagonal 六角形的,六角的hindrance 障碍,障碍物hob 滚刀,冲头hollow-ware 空心件horizontal 水平的hose 软管,水管hyperbolic 双曲线的i.e. (id est) [拉]也就是identical 同样的identify 确定,识别idle 空闲的immediately 正好,恰好impact 冲击impart 给予implement 实现impossibility 不可能impression 型腔in contact with 接触in terms of 依据inasmuch (as) co因为,由于inch-to-metric conversions 英公制转换inclinable 可倾斜的inclusion 含物inconspicuous 不显眼的incorporate 合并,混合indentation 压痕indenter 压头independently 独自地,独立地inevitably 不可避免地inexpensive 便宜的inherently 固有的injection mould 注塑模injection 注射in-line-of-draw 直接脱模insert 嵌件inserted die 嵌入式凹模inspection 检查,监督installation 安装integration 集成intelligent 智能的intentinonally 加强地，集中地interface 界面internal 部的interpolation 插值法investment casting 熔模铸造irregular 不规则的，无规律irrespective of 不论,不管irrespective 不顾的,不考虑的issue 发布，发出joint line 结合线kerosene 煤油keyboard 健盘knock 敲，敲打lance 切缝lathe 车床latitude 自由lay out 布置limitation 限度,限制,局限(性) local intelligence 局部智能locate 定位logic 逻辑longitudinal 纵向的longitudinally 纵向的look upon 视作,看待lubrication 润滑machine shop 车间machine table 工作台machining 加工made-to-measure 定做maintenance 维护,维修majority 多数make use of 利用male 阳的,凸形的malfunction 故障mandrel 心轴manifestation 表现,显示massiveness 厚实，大块measure 大小,度量microcomputer 微型计算机microns 微米microprocessor 微处理器mild steel 低碳钢milling machine 铣床mineral 矿物,矿产minimise 把减到最少,最小化minute 微小的mirror image 镜像mirror 镜子moderate 适度的modification 修改,修正modulus 系数mold 模,铸模mold 制模,造型monitor 监控monograph 专著more often than not 常常motivation 动机mould split line 模具分型线moulding 注塑件move away from 抛弃multi-imprssion mould 多型腔模narrow 狭窄的NC (numerical control) 数控nevertheless 然而,不过nonferrous 不含铁的,非铁的normally 通常地novice 新手,初学者nozzle 喷嘴,注口numerical 数字的objectionable 有异议的，讨厌的observe 观察obviously 明显地off-line 脱机的on-line 联机operational 操作的,运作的opportunity 时机,机会opposing 对立的,对面的opposite 反面optimization 最优化orient 确定方向orthodox 正统的，正规的overall 全面的,全部的overbend 过度弯曲overcome 克服,战胜overlaping 重叠overriding 主要的,占优势的opposite 对立的,对面的pack 包装package 包装pallet 货盘panel 面板paraffin 石蜡parallel 平行的penetration 穿透peripheral 外围的periphery 外围permit 许可,允许pessure casting 压力铸造pillar 柱子,导柱pin 销,栓,钉pin-point gate 针点式浇口piston 活塞plan view 主视图plasma 等离子plastic 塑料platen 压板plotter 绘图机plunge 翻孔plunge 投入plunger 柱塞pocket-size 袖珍portray 描绘pot 壶pour 灌,注practicable 行得通的preferable 更好的,更可取的preliminary 初步的，预备的press setter 装模工press 压,压床,冲床,压力机prevent 妨碍primarily 主要地procedure 步骤,方法,程序productivity 生产力profile 轮廓progressively 渐进地project 项目project 凸出projection 突出部分proper 本身的property 特性prototype 原形proximity 接近prudent 谨慎的punch 冲孔punch shapper tool 刨模机punch-cum-blanking die 凹凸模punched tape 穿孔带purchase 买，购买push back pin 回程杆pyrometer 高温计quality 质量quandrant 象限quantity 量，数量quench 淬火radial 放射状的ram 撞锤rapid 迅速的rapidly 迅速地raster 光栅raw 未加工的raw material 原材料ream 铰大reaming 扩孔,铰孔recall 记起,想起recede 收回,后退recess 凹槽,凹座,凹进处redundancy 过多re-entrant 凹入的refer 指,涉及,谈及reference 参照,参考refresh display 刷新显示register ring 定位环register 记录,显示,记数regrind 再磨研relative 相当的,比较的relay 继电器release 释放relegate 把降低到reliability 可靠性relief valves 安全阀relief 解除relieve 减轻,解除remainder 剩余物,其余部分removal 取出remove 切除,切削reposition 重新安排represent 代表,象征reputable 有名的,受尊敬的reservoir 容器,储存器resident 驻存的resist 抵抗resistance 阻力,抵抗resolution 分辨率respective 分别的,各自的respond 响应,作出反应responsibility 责任restrain 抑制restrict 限制，限定restriction 限制retain 保持,保留retaining plate 顶出固定板reveal 显示，展现reversal 反向right-angled 成直角的rigidity 钢度rod 杆,棒rotate (使)旋转rough machining 粗加工rough 粗略的routine 程序rubber 橡胶runner and gate systems 流道和浇口系统sand casting 砂型铸造satisfactorily 满意地saw 锯子scale 硬壳score 刻划scrap 废料,边角料,切屑screwcutting 切螺纹seal 密封section cutting plane 剖切面secure 固定secure 紧固,夹紧,固定segment 分割sensitive 敏感的sequence 次序sequential 相继的seriously 严重地servomechanism 伺服机构servomotor 伺服马达setter 安装者set-up 机构sever 切断severity 严重shaded 阴影的shank 柄shear 剪,切shot 注射shrink 收缩side sectional view 侧视图signal 信号similarity 类似simplicity 简单single-point cutting tool 单刃刀具situate 使位于,使处于slide 滑动,滑落slideway 导轨slot 槽slug 嵌条soak 浸,泡,均热software 软件solid 立体,固体solidify (使)凝固solidify (使)固化solution 溶液sophisiticated 尖端的,完善的sound 结实的,坚固的spark erosion 火花蚀刻spindle 主轴spline 花键split 侧向分型,分型spool 线轴springback 反弹spring-loaded 装弹簧的sprue bush 主流道衬套sprue puller 浇道拉杆square 使成方形Servomechanism Laboratoies 伺服机构实验室stage 阶段standardisation 标准化startling 令人吃惊的steadily 稳定地step-by-step 逐步stickiness 粘性stiffness 刚度stock 毛坯,坯料storage tube display 储存管显示storage 储存器straightforward 直接的strain 应变strength 强度stress 压力,应力stress-strain 应力--应变stretch 伸展strike 冲击stringent 严厉的stripper 推板stroke 冲程,行程structrural build-up 结构上形成的sub-base 垫板subject 使受到submerge 淹没subsequent 后来的subsequently 后来,随后substantial 实质的substitute 代替,替换subtract 减,减去suitable 合适的,适当的suitably 合适地sunk 下沉,下陷superior 上好的susceptible 易受影响的sweep away 扫过symmetrical 对称的synchronize 同步,同时发生tactile 触觉的,有触觉的tailstock 尾架tapered 锥形的tapping 攻丝technique 技术tempering 回火tendency 趋向,倾向tensile 拉力的,可拉伸的tension 拉紧,紧terminal 终端机terminology 术语,用辞theoretically 理论地thereby 因此,从而thermoplastic 热塑性的thermoplastic 热塑性塑料thermoset 热固性thoroughly 十分地,彻底地thread pitch 螺距thread 螺纹thrown up 推上tilt 倾斜,翘起tolerance 公差two-plate mould 双板式注射模tong 火钳tonnage 吨位,总吨数tool point 刀锋tool room 工具车间toolholder 刀夹,工具柄toolmaker 模具制造者toolpost grinder 工具磨床toolpost 刀架torsional 扭转的toughness 韧性trace 追踪transverse 横向的tray 盘，盘子，蝶treatment 处理tremendous 惊人的,巨大的trend 趋势trigger stop 始用挡料销tungsten 钨turning 车削twist 扭曲，扭转tracer-controlled milling machine 仿形铣床ultimately 终于undercut mould 侧向分型模undercut 侧向分型undercut 底切underfeed 底部进料的undergo 经受underside 下面,下侧undue 不适当的,过度的uniform 统一的,一致的utilize 利用Utopian 乌托邦的,理想化的valve 阀vaporize 汽化vaporize (使)蒸发variation 变化various 不同的,各种的vector feedrate computation 向量进刀速率计算vee 字形velocity 速度versatile 多才多艺的,万用的vertical 垂直的via prep经,通过vicinity 附近viewpoint 观点wander 偏离方向warp 翘曲washer 垫圈wear 磨损well line 结合线whereupon 于是winding 绕,卷with respect to 相对于withstand 经受,经得起work 工件workstage 工序wrinkle 皱纹使皱yield 生产zoom 图象电子放大runner less mold 无流道模hot runner mold 热流道模insulated runner mold 绝热流道模warm runner mold 温流道模runner plate 流道板warm runner plate 温流道板sprue 直浇道，主流道，浇口runless injiection 无流道冷料模具hot-runner mold 热流道模具runner ejector set 流道顶出器runner lock pin 流道拉梢shoot 流道die block steel 模具钢die material 模具材料cold work tool (die) steel 冷作工具（模具）钢hot work tool (die) steel 热作工具（模具）钢holder of punch 凸模夹持器die slide 下模滑动装置turret press 冲模回转压力机blanking die 冲裁模piercing die 冲孔模die,stamping and punching die 冲模die life 冲模寿命die shut height 模具闭合高度clearance between punch and die 凹凸模间隙peak die load 模具最大负荷matrix plate凹模固定板clearance between punch and die 凹凸模间隙matrix plate 凹模固定板cavity plate (block) 凹模die block凸模固定板button die 镶入式圆形凸模gib 凹形拉紧销spanishing凹痕印刷concave angle 凹角concave cutter 凹面铣刀depression 外缩凹孔sinking 凹陷single redessed单面缩凹形clamp-off 铸件凹痕riding 凹陷holder of punch 凸模夹持器clearance between punch and die凹凸模间隙counter punch反凸模angular cams 角凸轮flanged pin 带凸缘销weld flush焊缝凸起flange joint凸缘接头flange connection 凸缘联接convex cutter 凸形铣刀belling 压凸加工cam die bending 凸轮弯曲加工flabging 凸缘加工lug 凸缘crowing 中凸研磨flage wrinkel 凸缘起皱bent pilot 弯曲导正销baffle 导流块ejector guide pin 推板导柱ejector guide bush 板导推套dowel hole 导套孔ejector guide pin 顶出导梢ejector leader busher顶出导梢衬套guide bushing 引导衬套guide pin导梢guide plate 导板guide post 引导柱guide rail 导轨locating pilot pin 定位导梢pass guide穴型导板pilot pin 导销die slide下模滑动装置outer slide外滑块ball silder 球塞滑块slide(slide core) 滑块slip joint 滑配接头snap fit 滑入配合Screw thread lubricant 螺纹润滑剂drawing with ironing 抽引光滑加工dulling平滑glazing光滑剂shot chamber 注射室shot volume 注射量，压注量shot capacity 注射能力injection pressure压射比压，注射压力injection speed 注射速度injection forming 注射成形injection speed 注射速度injection mold 注射模injection mold for thermosets 热固性塑料注射模injection mold for thermoplastics 热塑性塑料注射模shot volume 注射量，压注量shot注射（射次）return-blank type blanking die顶出式落料模ejector guide pin 顶出导梢ejector pad 顶出垫ejector pin顶出梢ejector plate顶出板ejector rod 顶出杆ejector stopper 顶出止动ejector valve 顶出阀ejection pad 顶出衬垫ejector leader busher 顶出导梢衬套head punch 顶镦冲头lifting pin起模顶销pre extrusion punch顶挤冲头runner ejector set 流道顶出器prehardened steel 顶硬钢core-pulling force 抽芯力ejector guide pin 推板导柱ejector guide bush 板导推套ejector pin (plate) 推杆（板）ejector sleeve 推管ejector pin retaining plate 推杆固定板puncher 推杆taper key 推拔键thrust pin 推力销plain tapered bore 普通推拔孔taper shank推拔柄taper tap推拔螺丝攻sprue puller 拉料杆。
模具专业的英语词汇大全
WORD格式模具专业的英语词汇大全一、模具专业英语入水：gate进入位：gatelocation水口形式：gatetype大水口：edgegate细水口：pin-pointgate 水口大小：gatesize转水口：switchingrunner/gate唧嘴口径：spruediameter二、流道:runner热流道：hotrunner,hotmanifold热嘴冷流道:hotsprue/coldrunner:directspruegate圆形流道：round(full/halfrunnermoldflowanalysis流道平衡:runnerbalancehotsprue热流道板：hotmanifoldcartridgeheater探针:thermocouplesconnectorplug插座：connectorsocket/封料：seal三、运水：waterline喉塞：linelpug喉管：tube塑胶管：plastictube快速接头：jiffyquickconnectorplug/socker四、模具零件：moldcomponents三板模：3-platemold二板模：2-platemold/导边：leaderpin/guidepin边司/导套：bushing/guidebushingshoulderguidebushing中托边L：guidepinejectorretainnerplate托板：supportplatescrew管钉：dowelpinplybarscot内模管位：core/cavityinter-lockWORD格式ejectorpin司筒：ejectorsleeveejectorpin推板：stripperplatemovablecore,returncorecorepullernylonlatchlock斜顶：liftermoldbase上内模：cavityinsertcoreinsert行位（滑块）：slideinsert压座/斜鸡：wedge/油板：wedgewearplate压条：plate:supportpillar唧嘴：spruebushingstopplate定位圈：locatingringlatch扣鸡：partinglocksetpushbar栓打螺丝：S.H.S.Beracuretun活动臂：leverarmspuresperader水口司:bushstoppin隔片：bufflespringrod弹弓:diespringejectorguidebush中托边：ejectorguidepinpin销子：dowelpinballcatch模具成形不良用语英汉对照aberration色差atomization?化bankmark?料纹bite咬入blackinghole涂料孔(铸疵)blackingscab涂料疤WORD格式blister起泡blooming起霜lowhole破孔blushing泛白bodywrinkle侧壁皱纹breaking-in冒口带肉bubble膜泡burnmark糊斑burr毛边camber翘曲cell气泡centerbuckle表面中部波皱check细裂痕checking龟裂chipping修整表面缺陷clamp-off铸件凹痕collapse塌陷colormottle色斑corrosion腐蚀crack裂痕crazing碎裂crazing龟裂deformation变形edge切边碎片edgecrack裂边fading退色fillerspeak填充料斑fissure裂纹flangewrinkle凸缘起皱flaw刮伤flowmark流痕galling毛边glazing光滑gloss光泽greasepits污斑grindingdefect磨痕haircrack发裂haze雾度incrustation水锈indentation压痕internalporosity内部气孔mismatch偏模mottle斑点necking缩颈WORD格式nick割痕orangepeel橘皮状表面缺陷overflow溢流peeling剥离pit坑pittingcorrosion点状腐蚀platemark模板印痕pock麻点pockmark痘斑resinstreak树脂流纹resinwear树脂脱落riding凹陷sagging松垂saponification皂化scar疤痕scrap废料scrapjam废料阻塞scratch刮伤/划痕scuffing深冲表面划伤seam裂痕shockline模口挤痕shortshot充填不足shrinkagepool凹孔sinkmark凹痕skininclusion表皮折叠straightening矫直streak条状痕surfacecheck表面裂痕surfaceroughening橘皮状表皮皱折surging波动sweatout冒汗torsion扭曲warpage翘曲waviness波痕webbing熔塌weldmark焊痕whitening白化wrinkle皱纹各式模具分类用语英汉对照landedplungermold有肩柱塞式模具burnishingdie挤光模landedpositivemold有肩全压式模具buttondie镶入式圆形凹模loadingshoemold料套式模具WORD格式center-gatedmold中心浇口式模具loosedetailmold活零件模具chillmold冷硬用铸模loosemold活动式模具clodhobbing冷挤压制模louveringdie百叶窗冲切模compositedies复合模具manifolddie分歧管模具counterpunch反凸模modularmold组合式模具doublestackmold双层模具multi-cavitymold多模穴模具electroformedmold电铸成形模multi-gatemold复式浇口模具expanderdie扩径模offswtbendingdie双折冷弯模具extrusiondie挤出模palletizingdie叠层模familymold反套制品模具plastermold石膏模blankthroughdies漏件式落料模porousmold通气性模具duplicatedcavityplate复板模positivemold全压式模具fantaildie扇尾形模具pressuredie压紧模fishtaildie鱼尾形模具profiledie轮廓模flashmold溢料式模具progressivedie顺序模gypsummold石膏铸模protablemold手提式模具hot-runnermold热流道模具prototypemold雏形试验模具ingotmold钢锭模punchingdie落料模lancingdie切口模raising(embossing)压花起伏成形re-entrantmold倒角式模具sectionaldie拼合模runlessinjectionmold无流道冷料模具sectionaldie对合模具segmentmold组合模semi-positivemold半全压式模具WORD格式shaper定型模套singlecavitymold单腔模具solidforgingdie整体锻模splitforgingdie拼合锻模splitmold双并式模具spruelessmold无注道残料模具squeezingdie挤压模stretchformdie拉伸成形模sweepingmold平刮铸模swingdie振动模具threeplatesmold三片式模具trimmingdie切边模unitmold单元式模具universalmold通用模具unscrewingmold退扣式模具yoketypedie轭型模各种模具常用成形方式英汉对照accuratediecasting精密压铸powderforming粉末成形calendaringmolding压延成形powdermetalforging粉末锻造coldchamberdiecasting冷式压铸precisionforging精密锻造coldforging冷锻pressforging冲锻compactingmolding粉末压出成形rockingdieforging摇动锻造compoundmolding复合成形rotaryforging回转锻造compressionmolding压缩成形rotationalmolding离心成形dipmold浸渍成形rubbermolding橡胶成形encapsulationmolding注入成形sandmoldcasting砂模铸造extrusionmolding挤出成形shellcasting壳模铸造foamforming?泡成形sinterforging烧结锻造forgingroll轧锻sixsidesforging六面锻造gravitycasting重力铸造slushmolding凝塑成形hollow(blow)molding中空(吹出)成形WORD格式squeezecasting高压铸造hotchamberdiecasting热室压铸swaging挤锻hotforging热锻transfermolding转送成形injectionmolding射出成形warmforging温锻investmentcasting精密铸造matcheddiemethod对模成形法laminatingmethod被覆淋膜成形lowpressurecasting低压铸造lostwaxcasting脱蜡铸造matchedmouldthermalforming对模热成形模机械类常用英语：冲压模具-零件类punch冲头insert入块(嵌入件)deburringpunch压毛边冲子groovepunch压线冲子stampedpunch字模冲子roundpunch圆冲子specialshapepunch异形冲子bendingblock折刀roller滚轴baffleplate挡块locatedblock定位块supportingblockforlocation定位支承块aircushionplate气垫板air-cushioneject-rod气垫顶杆trimmingpunch切边冲子stiffeningribpunch=stinger加强筋冲子ribbonpunch压筋冲子reel-stretchpunch卷圆压平冲子guideplate定位板slidingblock滑块slidingdowelblock滑块固定块activeplate活动板lowerslidingplate下滑块板upperholderblock上压块uppermidplate上中间板springbox弹簧箱spring-boxeject-rod弹簧箱顶杆spring-boxeject-plate弹簧箱顶板bushingbolck衬套WORD格式coverplate盖板guidepad导料块机械类常用英语：冲压模具-模板类topplate上托板（顶板）topblock上垫脚punchset上模座punchpad上垫板punchholder上夹板stripperpad脱料背板upstripper上脱料板maledie公模(凸模)featuredie公母模femaledie母模(凹模)upperplate上模板lowerplate下模板diepad下垫板dieholder下夹板dieset下模座bottomblock下垫脚bottomplate下托板(底板)strippingplate内外打(脱料板)outerstripper外脱料板innerstripper内脱料板lowerstripper下脱料板冲压模具-冲压名称类英汉对照plaindie简易模piercedie冲孔模formingdie成型模progressivedie连续模gangdies复合模shearingdie剪边模rivetingdie铆合模pierce冲孔forming成型(抽凸,冲凸)drawhole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stampmark冲记号deburrorcoin压毛边WORD格式punchriveting冲压铆合sidestretch侧冲压平reelstretch卷圆压平groove压线blanking下料stampletter冲字(料号)shearing剪断tick-marknearside正面压印tick-markfarside反面压印extensiondwg展开图proceduredwg工程图diestructuredwg模具结构图material材质materialthickness料片厚度factor系数upward向上downward向下pressspecification冲床规格dieheightrange适用模高dieheight闭模高度burr毛边gap间隙weight重量totalwt.总重量punchwt.上模重量。
模具专业的英语词汇大全
模具专业的英语词汇大全一、模具基础词汇1. Mold 模具2. Die 冲模3. Core 核心模4. Cavity 型腔5. Mold Base 模架6. Mold Steel 模具钢7. Runner 流道8. Gate 进浇口9. Ejector Pin 顶针10. Ejector Plate 顶板二、模具设计相关词汇1. Draft Angle 脱模斜度2. Parting Line 分模线3. Radius 圆角4. Undercut 难以脱模的凹槽5. Slide 滑块6. Lifters 顶杆7. Cooling Channel 冷却水道8. Injection Point 注射点9. Shrinkage 收缩率10. Molding Cycle 成型周期三、模具加工与维护词汇1. Machining 加工2. Milling 铣削3. Grinding 磨削4. EDM (Electrical Discharge Machining) 电火花加工5. Wire Cutting 线切割6. Polishing 抛光7. Assembly 装配8. Maintenance 维护9. Repair 修理10. Replacement 更换四、模具材料与热处理词汇1. Tool Steel 工具钢2. Stainless Steel 不锈钢3. Aluminum 铝4. Plastic 塑料5. Rubber 橡胶6. Heat Treatment 热处理7. Hardness 硬度8. Tempering 回火9. Quenching 淬火10. Annealing 退火五、模具行业相关词汇1. Mold Maker 模具师傅2. Mold Designer 模具设计师3. Mold Manufacturer 模具制造商4. Injection Molding 注塑成型5. Blow Molding 吹塑成型6. Compression Molding 压缩成型7. Transfer Molding 传递成型8. Prototype Model 原型模具9. Mass Production 批量生产10. Quality Inspection 质量检验六、模具测试与质量控制词汇1. First Article Inspection 首件检查2. Sample 样品3. Defect 缺陷4. Dimensional Accuracy 尺寸精度5. Tolerance 公差6. Surface Finish 表面光洁度7. Stress Analysis 应力分析8. Flow Analysis 流动分析9. Mold Flow Simulation 模具流动模拟10. Quality Control 质量控制七、模具行业常用设备词汇1. Injection Molding Machine 注塑机2. Extruder 挤出机3. Blow Molding Machine 吹塑机4. CNC Machine 数控机床5. Lathe 车床6. Milling Machine 铣床7. Grinder 磨床8. EDM Machine 电火花机床9. Laser Cutter 激光切割机10. Robot 自动化八、模具生产流程词汇1. Design Drawing 设计图纸2. Mold Construction 模具构建3. Machining Process 加工工艺4. Tooling Setup 模具安装5. Trial Run 试模6. Adjustment 调整7. Production Run 生产运行8. Mold Maintenance 模具保养9. Mold Modification 模具修改10. Mold Recycling 模具回收九、模具行业认证与标准词汇1. ISO Certification ISO认证2. Quality Management System 质量管理体系3. Standard 标准化4. DIN 德国工业标准5. ASTM 美国材料与试验协会6. JIS 日本工业标准7. Certification Body 认证机构8. Audit 审核检查9. Compliance 符合性10. Continuous Improvement 持续改进十、模具行业发展趋势词汇1. Automation 自动化2. Intelligent Manufacturing 智能制造3. 3D Printing 三维打印4. Rapid Prototyping 快速原型5. Industry 4.0 工业4.06. Internet of Things (IoT) 物联网7. Big Data 大数据8. Cloud Computing 云计算9. Sustainable Development 可持续发展10. CrossIndustry Integration 跨行业整合通过这些词汇，我们可以看到模具行业不仅涉及具体的技术和操作，还包括了管理、质量控制、认证以及未来的发展趋势。
模具专业英语词汇
Injection Mold Technical Terms(一)模具专业基本用词Professional Terms1.塑料—plastic, resin2.样件—sample3.钢料—steel4.注塑机—injection machine, press5.产品—part, product, moulding6.模具—mold, mould, toolA 简易模(样板模)—prototype moldB 量产用模具—production mold7.三维造型(数模)—3D model, 3D data8.二维产品图—2D part drawing9.设计—design10.制造—manufacture, build up, construction11.检验—check, inspection12.测量—measure, inspection13.修改—change, modify, correction14.工程更改—engineer change15.质量—quality16.数量—quantity17.基准—datum, reference牛角入水-rads gate(二)如何解析2D 产品图?How to read 2D part drawing?一.产品几何Geometry1.点—point2.线(边)—line, edge3.面faceA 侧面—sideB 表面—surfaceC 外观面—appearance surface4.壁厚—wall thickness, stock thickness5.加强筋(骨位)—rib6.孔—hole7.细长的槽—slot8.柱位—boss9.角—cornerA 圆角—filletB 倒角—chamferC 尖角—sharp corner10.斜度—angle, taper11. 凹槽—recess , groove第 1 页共11 页二.分模信息Splitting1.分型线—parting line (P/L), splitting line2.主分模方向—main direction, line of draw3.浇口设定—gating产品标识Part Identification1.产品名称—part name (P/N)2.产品编号+版本号—part number + revision (Rev.)3.型腔号—cavity number4.材料标记—material symbol5.模具编号—mold number (no.)6.日期印—dating insert, date code7.循环印—cycling code8.公司标志—company logo三.技术要求Specification (Special Requirement)1.项目启动表Kick-off sheet1)项目名称—program name, project name2)产品名称—part name, product name, part description3)产品编号—part number (P/N)4)客户模号—customer mold no.5)项目启动日期—kick off date, start date6)项目完成日期—due date,lead time7)内模件用钢—tool steel8)型腔数量—number of cavities9)数据文件编号—data file no.10)注塑材料—resin, plastic, raw material11)收缩率—shrink, shrinkage, shrink factor12)注塑机吨位—molding machine size, injection machine size13)成型周期—cycle time14)型腔光洁度—cavity polish15)型芯光洁度—core polish16)皮纹(晒纹)—texture, grain17)拔模斜度—draft angle, removal taper18)注塑件颜色及光泽—molded color & gloss19)模具加工地—manufacturing facility20)热流道供应商—manifold manufacturer, manifold supplier21)浇口位置—gate location / position22)浇口类型—gate type23)产品标识—stamp information, part identification24)特殊要求—special instructions25)安全模数—safe steel2.产品质量及外观要求Part Quality & Appearance Requirement1)尺寸及公差Dimension & Tolerance①重要尺寸—critical dimension, important dim., key dim.②理论尺寸—nominal dimension③实际尺寸—actual dimension④公差—tolerance⑤公差带—tolerance range⑥尺寸超差—dimension deviation⑦接受(合格)—accept, OK⑧拒绝(不合格)—reject, refuse, obsolete, NG⑨让步接受—concession, special admit⑩返工—re-work2)产品缺陷(常见的)Defects (normal)①缩水—sink mark, shrinkage②飞边,毛边—flash, burr③段差—mismatch discrepancy④银丝纹,蛇纹—snake marks, streak⑤弯曲,变形—warpage, distortion⑥打不饱(缺料)—short shot⑦熔接线—weld line⑧多胶—unwanted plastic⑨拉伤—damage3.产品外观Part Appearance①产品颜色—part color②产品光泽—gloss③皮纹粒度—grain4.常用词汇、词组及短语Normal Word, Short Sentence1)单边—per side2)双边—both sides3)加入,添加—add, incorporate4)去除,取消—remove, cancel5)满足…的要求,符合,与…要求一致—according to, conform to, satisfy, meet6)要求,需要—require, need, demand7)确认—be approved, agreed by …8)允许—permit, allow9)在…范围之内—within10)不可以,不允许,禁止—free from, prevent, avoid11)…,除非有另指—…unless otherwise specified12)…或少于—…or less13)自动化运作—automatic operation14)未注尺寸(详细形状)见三维造型Non dimensioned contour (detailed shape) see 3D model. 15)分型线上的飞边(披缝)或段差应小于…Burrs or discrepancy on the P/L shall be … or less.四.标题栏Title Block1.产品名称—part name2.图纸编号 + 版本号(索引号)—drawing no. + level (index)3.一般公差—general tolerance(三)如何阅读制模标准?How to read tooling standard?一.模具结构术语Mold Construction TermsA.模架Mold Base1.模架量化特征Measurement Feature①长X 宽X 高—Length X Width X Height②模具高度尺寸(模厚)—stack height of mould③模具重量—total weight of mould, mould thickness2.定模底板—front plate, top clamping plate, clamp plate, clamping plate3.定模板—cavity plate, fixed mould plate, A – plate4.动模板—core plate, moving mould plate, B – plate5.浮动板—floating plate6.支撑板—support plate, backing plate7.间隔板,方铁—support blocks, rails, risers, spacer block8.顶杆固定板—retaining plate, ejector retaining plate9.顶板—ejector plate,bottom clamping plate10.动模底板—back plate11.导柱—guide pillar, leader pin, guide pin12.导套—guide bush, leader pin bush13.复位杆—return pin, push-back pin14.弹簧—spring15.撑头—support pillar16.顶针板导柱、导套—ejection guide pin / bush17.垃圾钉—stop pin, stop button18.模脚—standing-off pillars19.标牌—plaque scutcheonB.成型零部件moulding components20.型芯—core insert21.型腔—cavity insert22.镶针—core pin23.镶块—sub-insert, split24.滑块—slide, sliding split25.斜顶—lifter, angled-lift splitA 斜顶头—lifter headB 斜顶杆—lifter rod, lifter shaftC 斜顶连接块——lifter couplingD 斜顶导向块——lifter guideE 斜顶导滑块——lifter Gib26.成型顶杆—moulding face pin, form pinC.浇注系统Feed System1.塑料Plastica.主流道—sprueb.分流道runner①主分流道—main runner②二级分流道—branch runner分流道断面形状cross-sectional shape of runner①圆形—full round②半圆形—semicircular③梯形—trapezoidalc.浇口gate常用浇口形式normal gate type :①边缘浇口(J型浇口)—edge gate, J – gate②侧浇口—side gate③潜伏式浇口—sub-gate, cashew gate, subsurface gate, submarine gate潜顶针—subgate to pin④潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤点浇口—pin gate⑥直接浇口(主流道型浇口) —sprue gate, direct gate⑦护耳式浇口—tab gated.模腔—impressione.冷料井—cold slug wellf.热流道—hot runner2.模具零件mold componentsa.定位圈—locating ring, location ring, register ringb.浇口套—sprue bushc.挡圈—stop ringd.浇口镶块—gate inserte.热流道板—manifoldf.热嘴—hot dropD.分型面及其锁紧、排气Parting Surface, inter-locking & venting1.分型线—parting line ( P/L )2.镶拼线—bodyline, joint line3.平/ 不平的分型面—flat / non – flat parting surface4.封胶面—shut off surfaces, seal-off surfaces5.擦穿位—shut off6.碰穿位—kiss-off7.管位—parting line lock8.分型面的释放(避空) —relief of parting surface9.分型面的平衡—balancing of parting surface10.锁紧角度—locking angle11.锁紧力—clamping force12.锁模块—safety strap13.精定位—Interlock, die lock14.困气—air trap15.排气槽—vent, vent slot16.撬模坑--- pry slot17.计数器--- shot counter/ cycle counterE.滑块机构Slide1.驱动Actuation①斜导柱—angle pin, horn pin, cam pin②弹簧—spring③油缸—hydraulic cylinder2.制动Detention①滑块固定器—slide retainer②弹簧制动器—spring-loaded detention (plunger)③挡钉、挡板—stop pin, stop plate, slide stop3.导轨—gib, guide strip,center guide4.锁紧块(楔紧块)—heel block, locking heel, wedge block, chase block,slide driver5.耐磨片—wear plate, wear strip6.压板—retainer,gib7.螺钉—screw8.定位销—dowel pin9.行位扣—slide lock / slide retainer10. flat ejector pin 扁顶针F.斜顶机构Lifter1.斜顶头—lifter head2.斜顶杆—lifter rod, lifter shaft3.斜顶固定块—lifter rod retainer4.斜顶导向块—lifter guide5.开口销—split pin6.固定板(压板)—retainer plate7.耐磨片—wear plate8.铜导套—bronze bushing9.导套固定板—bushing retainer10.衬套—spacer11.导轨—L – gib12.导轨---T-Gib13.滑动块—slide14.连接块—U-CouplingG.顶出系统Ejection System1.基本词汇Basic Word①顶出行程—ejection stroke②模具开档—daylight③粘模—stick on④产品脱模—part is push off from, clear part of mould, separation of part2.顶板机构Ejector plate assembly①顶板—ejector plate②顶板固定板—retaining plate③推板—stripper plate④推板导柱—ejector guide pin⑤推板导套—ejector guide bush⑥撑头—support pillar⑦限位块—stop block,stroke block3.复位机构Return System①复位杆(回程杆)—return pin, push – back pin②垃圾钉—stop pin, stop button③压簧—compressed spring④碟簧—a stack of ―Belleville‖ washers⑤早复位机构—early return system⑥强制复位机构—positive return system4.顶出方法Ejection Techniques1)顶杆顶出—pin ejection2)顶管顶出—sleeve ejection3)顶块顶出—bar ejection4)扁顶顶出—blade ejection5)顶板顶出—stripper ejection6)油缸顶出—hydraulic ejection7)气顶—air ejection8)阀门顶出—valve ejection5.顶出元件Ejection Elements1)拉料杆—sprue puller, sucker pin2)顶杆—ejector pin3)阶梯式顶杆—stepped ejector pin4)顶管—ejection sleeve, sleeve5)扁顶—ejector blade, slabbed off ejector pin6)顶块—stripper bar7)顶环—stripper ring8)推板—stripper plate9)加速顶—accelerated ejection10)直顶----straight lifter/EJECTOR BAR6.顶出辅助机构Supplementary operating system1)弹簧柱塞器—spring – loaded plunger2)弹珠定位器—ball catch system3)插销式锁扣—Latch – lock4)尼龙拉杆装置—friction puller device7.电器元件Electric Components1)压力传感器—pressure transducer2)限位开关—limit switchF.冷却系统Cooling System1.基本词汇Basic Word1)温差—temperature variation2)水孔(水道)—waterlines, water-ways, flow-way, channel3)水路—cooling circuit4)水路示意图—water schematic, schematic circuit5)冷却液—coolant, coolant fluid6)内连接—interconnect7)外连接—external connection8)出口、入口—outlet、inlet9)漏水—water leakage2.水路分布Circuits1)阶梯式水路—stepped system2)分隔板水路—baffled hole system3)斜孔式水路—angled hole system3.水路元件Components1)闷头(螺塞、止水栓)—(threadless)brass pressure plug : female plug & male2)隔水片—baffle3)密封圈—O – ring4)快插水路接头—quick disconnect fitting, quick connection adaptor5)弯头—elbow6)偶合器(连接器、接头)—adaptor (including a plug & a socket)7)橡皮管—rubber hose8)分水板,集水块—water manifoldG.螺纹、螺纹孔& 螺钉Thread, thread hole & screw1.螺纹—thread2.管螺纹—pipe thread3.螺纹孔—screw hole, tapped hole4.起吊孔—handling hole, jack screw hole, eye bolt hole5.螺钉—screw6.内六角螺钉—socket headed cap screw (s.h.c.s.)7.沉头螺钉—flat headed cap screw (f.h.c.s)8.螺栓—bolt9.螺母—nut10.锁紧螺母—locknut11.螺纹标准Thread Standard①公制标准—Metric②英制标准—Imperial③英制管螺纹标准—British Standard Pipe thread (BSP)④美制管螺纹标准—NPT⑤美制粗螺纹标准—United Coarse thread (UNC)⑥美制细螺纹标准—United Fine thread (UNF)H.润滑Lubrication1.润滑槽—grease groove2.加油管—grease line3.油杯—lubrication fittingI.测量仪器Measuring Instruments1.游标卡尺—vernier caliper2.千分尺—micrometer3.高度规—height gauge4.刻度规—dial gauge5.三坐标测量仪(三次元)—Coordinate Measure Machine(CMM)6.塞规—pin gauge7.圆角量规—radii gauge8.轮廓投影机—profile projectorJ.注塑机参数Injection Machine Parameter1.注塑机规格参数Injection Machine Specification①锁紧类型clamp typea.油缸—hydraulicb.肘杆式—toggle②垂直注塑机导柱间距—tie bar vertical clearance③水平注塑机导柱间距—tie bar horizontal clearance④台板尺寸—platen dim.⑤最小/ 最大模厚—mold height Min. / Max., Min. / Max. mold thickness⑥最小/ 最大注塑机开档—open daylight Min. / Max.⑦锁紧行程—clamp stroke⑧锁紧力—clamping force⑨顶出行程—ejector stroke⑩顶出力—ejector force2.试模工艺参数Moulding Process Parameter, machine setting①时间Timer(TM), seca.注塑(充填)时间—filling time, injection timeb.冷却时间—cooling timec.补缩时间—packing timed.保压时间—holding timee.成型周期—cycle time②速率、速度Velocity, %、speed, in/seca.注塑(充填)速度—injection speedb.保压速率—hold pressure velocityc.螺杆转速—screw rotation speed③压力Pressure(Prs.), psia.注塑压力—injection pressureb.保压压力—hold pressurec.回压(背压)—back pressure④温度Temperature(Temp.), °Fa.注塑机喷嘴温度—nozzle temp.b.料筒前段、中段、后段温度—barrel front、middle、rear temp.c.模温—mould temp.d.料温—purged resin melt temp.e.空射料温—air shot melt temp. 第11 页共11 页。
模具专业英语词汇
模具专业英语词汇Aabrasion n. 磨损abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 Bback pressure 背压 bismutbaffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套barrel temperature 料筒温度 blush 发blank through dies 漏件式落料模 burnishblow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺buttonby-product n. 副产品 Ccalendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造catalyst n. 催化剂cavity n. 型腔chemical resistance n. 耐化学腐蚀性chip v. 削 /凿clamping force n. 锁模力clamping tonnage n. 锁模吨位coil spring弹簧computer aided design (CAD) n. 电脑辅助设计computer aided manufacture (CAM) n. 电脑辅助制造cover plate盖板computer numerical control (CNC) n. 电脑数字控制ceramic n. 陶瓷calendaring molding 压延成形cavity 型控母模center-gated mold 中心浇口式模具clod hobbing 冷挤压制模center-gated mold 中心浇口式模具clod hobbing 冷挤压制模chill mold 冷硬用铸模cold chamber die casting 冷式压铸cold forging 冷锻cold slag 冷料渣cold slug 冷斑cold rolled steel n. 冷轧圆钢cold runner n. 冷流道colorant n. 着色剂compacting molding 粉末压出成形composite n. 复合材料composite dies 复合模具compound molding 复合成形compression molding 压缩成形compression strength n. 抗压强度cooling channel/circuit n. 冷却管道cooling rate n. 冷却速率core n. 型芯 /模芯corrosion n. 腐蚀corrosion resistance n. 耐腐蚀性counter punch 反凸模cure v. 固化custom adj. 定制cycle time n. 循环时间Ddegassing n. 排气density n. 密度deform v. 变形delamination 起皮diaphragm gate 隔膜浇口die n. 冲模die casting n. 压铸 /模铸deburring punch压毛边冲子die holder下夹板die pad下垫板die set下模座dimension n. 尺寸dimensional tolerance n. 尺寸公差dowel pin固定销dish gate 盘形浇口dip mold 浸渍成形distort v. 扭曲double stack mold 双层模具draft angle n. 拨模斜度drying 烘干duplicated cavity plate 复板模dwell time n. 驻留时间dye n. 染料Eedge gate 侧缘浇口ejector mark n. 顶出痕迹ejection pin n. 顶出杆/推顶锁 /脱模锁ejection plate n. 推顶板/脱模板ejection rod n. 脱模板拉杆elastomer n. 弹性体electrical discharge machining (EDM) n. 电火花加工electroformed mold 电铸成形模encapsulation molding 注入成形epoxy n. 环氧树脂eq-height sleeves=spool等高套筒expander die 扩径模extruder n. 挤出机extrusion n. 挤出，挤塑extrusion die 挤出模extrusion molding 挤出成形Ffabricate v. 制造family mold 反套制品模具fan gate 扇形浇口fantail die 扇尾形模具fiber n. 纤维feature die公母模female die母模(凹模) fiberglass n. 玻璃纤维fiber reinforcement n. 纤维增强film n. 薄膜film gate 薄膜浇口fire retardant n. 阻燃剂fishtail die 鱼尾形模具flash 飞边/溢料flash gate 闸门浇口flash mold 溢料式模具flaw/scratch 刮伤flexural modulus 弯曲模数flexural strength 抗弯强度flow line 流痕flow mark n. 流痕flow rate n. 流动速率fluorescent adj. 荧光fluorescent brightener n. 荧光增白剂foam n. 泡沫fuse v. 熔合Ggang dies 复合模gas assisted injection molding n. 气辅注射成型gate n. 浇口gate design 浇口设计gate mark n. 浇口痕gear n. 齿轮grinder n. 研磨机 /磨床gas mark 烧焦glazing 光滑gloss 光泽foam forming 发泡成形forming die 成型模forging roll 轧锻gravity casting 重力铸造groove punch压线冲子guide pin导正销guide plate定位板guide pad导料块gypsum mold 石膏铸模Hheat conduction n. 热传导heater band n. 加热圈heat treatment n. 热处理hesitation 迟滞high density polyethylene (HDPE) n. 高密度聚乙烯high impact plastic n. 高抗冲塑料high impact polystyrene n. 高抗冲聚苯乙烯hobbing n. 滚铣/挤压制模 /切压制模holding n. 保压hollow(blow) molding 中空(吹出)成形hot runner n. 热流道hot chamber die casting 热室压铸hot forging 热锻hot-runner mold 热流道模具Iimpact strength n. 冲击强度ingot mold 钢锭模injection n. 注射/注塑injection mold 注塑模injection molding 射出成形injection molding machine n. 注塑机injection pressure 注塑压力injection speed 注塑速度inner stripper内脱料板inner guiding post内导柱inner hexagon screw内六角螺钉insert入块(嵌入件)insulated runner n. 绝热流道/保温流道insulation layer n. 绝热层internally heated runner n. 内加热流道internal void n. 内部空腔investment casting 精密铸造Jjoint n. 接头/连接/Llancing die 切口模laminating method 被覆淋膜成形lancing die 切口模landed plunger mold 有肩柱塞式模具landed positive mold 有肩全压式模具laser n. 激光laser cutter n. 激光切割机lathe n. 车床lifter guide pin浮升导料销lifter pin顶料销located block定位块located pin定位销loading shoe mold 料套式模具loose detail mold 活零件模具long nozzle 延长喷嘴方式loose mold 活动式模具louvering die 百叶窗冲切模lost wax casting 脱蜡铸造low density polyethylene n. 低密度聚乙烯low pressure casting 低压铸造lower plate下模板lower sliding plate下滑块板lower stripper下脱料板Mmale die公模(凸模)main runner 主流道manifold die 分歧管模具melt v. 熔融melt index n. 熔融指数mill (metal) v. 铣machining n. 机加工machining path n. 加工路径manufacture v. 制造matched die method 对模成形法matched mould thermal forming 对模热成形模meld line n. 融合线metal machining n. 金属加工melt temperature 熔化温度milling machine n. 铣床model n. 模型modular mold 组合式模具monomer n. 单体mold n. 模具mold cavity n. 模具型腔mold life n. 模具寿命mold temperature 模具温度molding conditions 成型条件modular mold 组合式模具multi color injection molding n. 多色注塑multi-cavity mold 多模穴模具multi-gate mold 复式浇口模具multi shot injection molding n. 多次注料注塑Nnozzle n. 喷嘴Nylon n. 尼龙O offset bending die 双折冷弯模具outer bush外导套outer guiding post外导柱outer stripper外脱料板oxidation resistance n. 耐氧化性oxidize v. 氧化Ppackaging n. 包装packing n. 补料palletizing die 叠层模parison n. 型坯part n. 零件parting line n. 分模线parting plane n. 分模面pierce die 冲孔模pin销pinhole gate n. 针孔形浇口pinpoint gate 点浇口plain die 简易模plaster mold 石膏模plastic n. 塑料plasticity n. 塑性plasticizer n. 增塑剂plotter n. 绘图机polish v. 抛光porous adj. 多孔precise adj. 精密polycarbonate (PC) n. 聚碳酸酯polyethylene n. 聚乙烯polyester n. 聚酯polymer n. 聚合物（体） /高聚物polymerization n. 聚合polystyrene n. 聚苯乙烯polyurethane n. 聚氨脂polyvinyl chloride (PVC) n. 聚氯乙烯porous mold 通气性模具positive mold 全压式/挤压式模具pressure die 压紧模profile die 轮廓模progressive die 顺序模portable mold 手提式模具positive mold 全压式模具powder forming 粉末成形powder metal forging 粉末锻造precision n. 精度precision injection machine n. 精密注塑机precision forging 精密锻造precision molding n. 精密模塑preform n. 预成型preform molding n. 预成型模塑press forging 冲锻pressure die 压紧模profile die 轮廓模progressive die 连续模/顺序模prototype mold 雏形试验模具process v. 处理chǔlǐ；加工production line n. 生产线prototype mold 雏形试验模具prototype n. 原型punch冲头punch set上模座punching die 落料模punch holder上夹板punch pad上垫板Qquench v. 淬火Rraising(embossing) 压花起伏成形re-entrant mold 倒角式模具reel-stretch punch卷圆压平冲子regrind n. 回用料regrind usage 次料使用resin n. 树脂rib n. 肋条rib stiffener n. 加强肋ribbon punch压筋冲子rigidity n. 刚性ring gate 环形浇口ripple n. 波纹/皱纹riveting die 铆合模rocking die forging 摇动锻造roller滚轴rotary forging 回转锻造rotational molding 离心成形rough adj. 粗糙round punch圆冲子rubber n. 橡胶 /橡皮írubber molding 橡胶成形runner n. 流道runner design 流道设计runner plat 浇道模块runner system浇道系统runnerless adj. 无流道runnerless injection mold n. 无流道注塑模具Ssand mold casting 砂模铸造scale n. 比例schematic n. 图解screw speed 螺杆转速seal v. 密封secondary runner 次流道sectional die 拼合模/对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套shearing die 剪边模shell casting 壳模铸造short shot n. 短射shot n. 注料shot size n. 注塑量shrinkage 收缩(率)side core n. 侧性芯side gate 侧浇口silicon n. 聚硅氧烷silicon rubber n. 硅橡胶simulate v. 模拟single cavity mold 单腔模具single gate mold n. 单浇口模具sink mark n. 凹痕 /缩痕sinter forging 烧结锻造six sides forging 六面锻造slag well 冷料井slide n. 滑动阀sliding block滑块sliding dowel block滑块固定块special shape punch异形冲子spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板stop screw止付螺丝stripper pad脱料背板stripping plate内外打(脱料板) supporting block for location定位支承块slit gate 缝隙浇口slush molding 凝塑成形softener n. 软化剂solid forging die 整体/拼合锻模splay 银纹split forging die 拼合锻模split mold 分割式模具/双并式模具sprue 注道/ 浇口/溶渣sprue/cold material trap 浇道/冷料井sprue gate 射料浇口，直浇口sprueless mold 无注道残料模具sprue lock pin 料头钩销(拉料杆)sprue puller 拉杆sprueless mold 无射料管方式/无注道残料模具squeeze casting 高压铸造squeezing die 挤压模steam channel n. 汽道stabilizer n. 稳定剂stamped punch字模冲子stamping n. 冲压stainless steel n. 不锈钢stiffening rib punch = stinger 加强筋冲子strain n. 应变streak n. 条纹 /条痕stretch form die 拉伸成形模stress n. 应力stripper n. 脱模器/顶出器stripper ring n. 脱模圈submarine gate 潜伏浇口surface defect n. 表面缺陷surface treatment n. 表面处理surface check 表面裂痕swing die 振动模具symmetrical adj. 对称symmetry n. 对称swaging 挤锻sweeping mold 平刮铸模Ttab gate 搭接浇口Teflon n. 特氟隆temper v. 回火tensile strength n. 抗张强度tensile elongation 延伸率thermoforming n. 热成型thermoplastic n. 热塑性塑料 adj. 热塑性thermoset n. 热固性塑料 adj. 热固性three-dimensional adj. 三维空间three plates mold 三片式模具tie bar n. 连接杆tolerance n. 公差tool mark n. 刀痕tool steel n. 工具钢top plate上托板（顶板）top block上垫脚transfer molding 转送成形trimming die 切边模trimming punch切边冲子tunnel gate 隧道式浇口Uultrasonic welder n. 超声波焊接机undercut n. 凹孔unit cost n. 单价unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具up stripper上脱料板upper plate上模板upper holder block上压块upper mid plate上中间板Vvacuum n. 真空valve gate阀门浇口vented injection molding n. 排气式注塑成型viscosity n. 黏度/黏性void 缩孔vulcanize v. 硫化Wwarm forging 温锻warpage n. 翘曲变形wear n. 磨损wear resistance n. 耐磨损性weld line n. 熔接线wire spring圆线弹簧working drawing n. 工程图yoke type die 轭型模机械设备:3D coordinate measurement 三次元量床boring machine 搪孔机contouring machine 轮廓锯床copy grinding machine 仿形磨床cylindrical grinding machine 外圆磨床die spotting machine 合模机driller 钻床EDM=Electron Discharge Machining 放电加工electrical sparkle 电火花engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机grinder 磨床horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床lathe车床linear cutting 线切割miller 铣床milling machine 铣床planer |刨床punching machine 冲床robot机械手welder 电焊机分类（汉英）一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components 三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot 撑头: support pillar 唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin五术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct c ut on B-plate. 内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length 稳定性好：good stability,stable强度不够：insufficient rigidity 均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrod根据国家标准，以下为部分塑料模具成形术语的标准翻译。
经典的 模具专业英语词汇表(中英对照)收藏起来吧
模具英语词汇表GLOSSARYAabrasive grinding 强力磨削 L3abrasive[E'breisiv] a.磨料的, 研磨的 L2,3 absence ['AbsEns] n.. 不在，缺席L17 accesssory[Ak'sesEri] n.附件L10 accommodate[E'kCmEdeit] v. 适应 L5 accordingly[E'kC:diNli] adv.因此,从而,相应地 L7,13 accuracy['AkjurEsi] n精度,准确性L1,3actuate['Aktjueit] vt.开动(机器), 驱动 L8 adequate['Adikwit] a. 足够的L13adhesive[Ed'hi:siv] n. 粘合剂L22adjacent[E'dVeisnt] a. 邻近的L13adopt[E'dCpt] vt. 采用 L4advance [Ed'vA:ns] n.进步 L7advisable [Ed'vaizbl] adj. 可取的L20agitate['AdViteit] v. 摇动 L2a large extent 很大程度 L4,13algorithm ['Al^EriTEm] n. 算法 L6align [E'lain] v 定位，调准L17alignment[E'lainmEnt] n. 校直L11all-too-frequent 频繁L17allowance[E'lEuens] n. 容差, 余量 L5alternate['C:ltEnit]v.交替,轮流L1alternative[C:l'tE:nEtiv] n. 替换物 L3 alternatively[C:l'tE:nEtivli] ad. 做为选择, 也许 L5 aluminiun[7Alju'minjEm] n.铝 L2ample['Ampl] adj. 充足的L20analysis [E'nAlEsis] n. 分析 L6ancillary['AnsilEri] a.补助的, 副的 L4angular ['A^julE] adj. 有角的L20annealing[E'li:liN] n.退火 L2aperture ['ApEtFE] n.孔L17applied loads 作用力L1appropriate [E'prEuprieit] a. 适当的 L6,20arc[a:k] n.弧, 弓形L10arise[E'raiz] vi. 出现, 发生L21arrange[E'reidV] v. 安排L12article['a:tikl] n.制品, 产品L21ascertain[7AsE'tein] vt. 确定, 查明L1assemble[E'sembl] vt.组装 L4attitude ['Atitju:d] n 态度L17auxiliary [C:^'ziljEri]adj. 辅助的 L8avoid[E'vCid] v.避免 L7axis['Aksis] n.轴 L5axle['Aksl] n.轮轴, 车轴L1Bbackup['bAk7Qp] n. 备份 L9batch [bAtF] n 一批L17bearing['bZEriN] n.轴承,支座L21bed[bed] n. 床身 L5behavior[bi'heivjE] n. 性能L1bench-work 钳工工作 L4bend[bend] v.弯曲L1beneath[bi'ni:W] prep在···下 L4bin [bin] n. 仓，料架L19blank [blANk] n. 坯料L20blank [blANk] v. 冲裁,落料L17blanking tool 落料模L17blast [blQst] n.一阵（风）L18blemish['blemiF] n. 缺点, 污点L13bolster['bEulstE] n. 模座,垫板 L4,5boost[bu:st] n. 推进 L9boring['bC:riN] n.镗削, 镗孔L4,5bracket ['brAkit] n. 支架L19brass [brAs] n.黄铜 L2break down 破坏L1breakage ['breikidV] n.破坏L17bridge piece L16brine[brain] n. 盐水 L2brittle['britl] adv.易碎的L1buffer [bQfE] n.缓冲器 L8built-in 内装的 L9bulging [bQldViN] n. 凸肚L22burr [bE:] n. 毛刺L17bush [buF] n. 衬套L17bush[buF]n. 衬套 L5by far (修饰比较级, 最高级)···得多, 最 L3 by means of 借助于 L5Ccabinet ['kAbinit] n.橱柜 L7call upon 要求L17carbide['ka:baid] n.碳化物L10 carburzing['ka:bjuretiN] n. 渗碳 L2 carriage['kAridV] n.拖板, 大拖板 L5carry along 一起带走L18carry down over 从···上取下L21carry out 完成L17case hardening 表面硬化 L2case[keis] n. 壳, 套 L2cast steel 铸钢L17casting['ka:stiN] n. 铸造,铸件 L3category['kAtE^Euri] n. 种类 L6,15caution ['kC:FEn] n. 警告，警示L17cavity and core plates 凹模和凸模板L11 cavity['kAviti] n.型腔, 腔, 洞 L4,10centre-drilling 中心孔 L5ceramic[si'rAmik] n.陶瓷制品 L3chain doted line 点划线L11channel['tFAnl] n.通道, 信道 L8 characteristic[kArEktE'ristik] n.特性L1check[tFek] v.核算L21chip[tFip] n.切屑, 铁屑 L3chuck [tFQk] n.卡盘L5,8chute [Fu:t] n. 斜道L19circa ['sEkE:] adv. 大约 L7circlip['sE:klip] n.(开口)簧环L22circuit['sE:kit] n. 回路, 环路L13circular supoport block L5circulate['sE:kjuleid] v.(使)循环L13clamp [klAmp] vt 夹紧L17clamp[klAmp] n.压板L12clay[klei] n. 泥土L2,7clearance ['kliErEns] n. 间隙L17clip [klip] vt. 切断，夹住L19cold hobbing 冷挤压 L4cold slug well 冷料井L12collapse[kE'lAps] vi.崩塌, 瓦解L22 collapsible[kE'lApsEbl] adj.可分解的L22 combination [kCmbi'neiFEn] n. 组合L18 commence[kE'mens] v. 开始, 着手L16 commence[kE'mens]v. 开始L21 commercial [kE'mE:FEl] adj. 商业的 L7 competitive[kEm'petitiv] a. 竞争的 L9 complementary[7kCmpli'mentEri] a. 互补的 L5 complexity [kem'pleksiti] n.复杂性 L8 complicated['kCmplEkeitid] adj.复杂的 L2 complication [kCmpli'keiFEn] n. 复杂化 L5,20 compression [kEm'preFEn] n.压缩L1 comprise[kEm'prais] vt.包含L16 compromise['kCmprEmaiz] n. 妥协, 折衷L13 concern with 关于 L6concise[kEn'sais] a. 简明的, 简练的 L9 confront[kEn'frQnt] vt. 使面临L14connector[kE'nektE] n. 连接口, 接头 L14 consequent['kCnsikwEnt] a. 随之发生的, 必然的 L3 console ['kCnsoul] n.控制台 L8consume [kEn'sjum] vt. 消耗, 占用 L7 consummate [kEn'sQmeit] vt. 使完善 L6 container[kEn'teinE] n. 容器L11contingent[ken'tindVEnt] a.可能发生的 L9 contour['kEntuE] n.轮廓 L5,21conventional[kEn'venFEnl] a. 常规的 L4 converge[kEn'vE:dV] v.集中于一点L21 conversant[kCn'vE:sEnt] a. 熟悉的L15 conversion[kEn'vE:FEn] n 换算, 转换 L7 conveyer[ken'veiE] n. 运送装置L12coolant['ku:lEnt] n. 冷却液L13coordinate [kEu'C:dnit] vt. (使)协调 L8copy machine 仿形(加工)机床 L4core[kC:] n. 型芯, 核心L2,4corresponding [ka:ri'spCdiN] n.相应的 L7 counteract [kauntE'rAkt] vt. 反作用,抵抗L20 couple with 伴随L20CPU (central processing unit) 中央处理器 L9 crack[krAk ] v.（使）破裂，裂纹 L1,17critical['kritikl] adj.临界的 L2cross-hatching 剖面线L16cross-section drawn 剖面图L11cross-slide 横向滑板 L5CRT (cathoder-ray tube) 阴极射线管 L9crush[krQF]vt.压碎L1cryogenic[7kraiE'dVenik ]a.低温学的L1crystal['kristl] adj.结晶状的L1cubic['kju:bik] a. 立方的, 立方体的 L3cup [kQp] vt (使)成杯状, 引伸L18curable ['kjurEbl] adj. 可矫正的L20curvature['kE:vEtFE] n.弧线L21curve [kE:v] vt. 使弯曲L20cutter bit 刀头, 刀片 L3cyanide['saiEnaid] n.氰化物 L2Ddash [dAF] n. 破折号 L6daylight ['deilait] n. 板距L12decline[di'klain] v.下落,下降,减少, L3,9deform[di'fC:m] v. (使)变形L1,3demonstrate['demEstreit ] v证明L21depict[di'pikt ] vt 描述L18deposite [di'pCzit] vt. 放置L20depression[di'preFEn] n. 凹穴L12descend [di'sent] v. 下降L20desirable[di'zairEbl] a. 合适的 L2detail ['diteil] n.细节，详情L17deterioration[ditiEri:E'reiFEn] n. 退化, 恶化L12 determine[di'tE:min] v.决定L16diagrammmatic[7daiEgrE'mAtik].a.图解的，图表的L10 dictate['dikteit] v. 支配L12die[dai] n.模具, 冲模, 凹模L2dielectric[daii'lektrik] n. 电介质L10die-set 模架L19digital ['didVitl ] n.数字式数字, a.数字的L3,6 dimensional[dddi'menFEnl] a. 尺寸的, 空间的 L3 discharge[dis'tFa:dV] n.v. 放电, 卸下, 排出 L3 discharge[dis'tFa:dV] v.卸下 L8discrete [dis'cri:t] adj. 离散的,分立的 L7dislodge[dis'lCdV] v. 拉出, 取出L12dissolution[disE'lu:FEn] n.结束 L9distinct [dis'tiNkt] a.不同的，显著的 L6distort [dis'dC:t] vt. 扭曲L20distort[dis'tC:t] vt. (使)变形, 扭曲L1distributed system 分布式系统 L9dowel ['dauEl] n. 销子L19dramaticlly [drE'mAtikli] adv. 显著地 L7drastic ['drAstik] a.激烈的L17draughting[dra:ftiN] n. 绘图L16draughtsman['drAftsmEn] n. 起草人L16drawing['drC:iN] n. 制图L11drill press 钻床 L8drum [drQm] n.鼓轮 L8dual ['dju:El] adv. 双的，双重的L18ductility [dQk'tiliti ] n.延展性 L1,21dynamic [dai'nAmik ] adj 动力的 L6Eedge [edV] n .边缘L20e.g.(exempli gratia) [拉] 例如L12ejector [i'dVektE] n.排出器，L18ejector plate 顶出板L16ejector rob 顶杆 L5elasticity[ilA'stisiti] n.弹性L1electric dicharge machining 电火花加工L3electrical discharge machining电火花加工 L10electrochemical machining 电化学加工L3electrode[i'lektrEud] n. 电极L10electro-deposition 电铸 L4elementary [elE'mentEri] adj.基本的 L2eliminate[i'limineit] vt. 消除, 除去L10 elongate[i'lCN^et] vt. (使)伸长, 延长L1 emerge [i'mE:dV] vi. 形成, 显现L20 emphasise['emfEsaiz] vt. 强调 L4 endeavour[en'devE] n. 尽力 L17 engagement[in'^eidVment] n. 约束, 接合L22 enhance[in'hAns] vt. 提高, 增强 L9ensure [in'FuE] vt. 确保，保证L17 envisage[in'vizidV] vt.设想L15erase[i'reis] vt. 抹去, 擦掉L16evaluation[i'vAlju7eiFEn] n. 评价, 估价L1 eventually[i'vEntFuEli ] adv.终于L21 evolution[evE'lu:FEn] n.进展L16 excecution[eksi'kju:FEn] n. 执行, 完成 L9 execute ['ekskju:t] v. 执行 L8exerte [i^'zE:t] vt. 施加L20experience[iks'piriEns] n. 经验L16 explosive[iks'plEusiv]adj.爆炸(性)的L22 extend[eks'tend] v. 伸展 L2external[eks'tE:nl] a. 外部的 L5,11 extract[eks'trAkt] v. 拔出L14extreme[iks'tri:m] n. 极端L13extremely[iks'tri:mli] adv. 非常地L12 extremity[iks'tmiti] n. 极端L13extrusion[eks'tru:VEn] n. 挤压, 挤出 L3FF (Fahrenheit)['fArEnhait]n.华氏温度 L2fabricate ['fAbrikeit] vt.制作,制造 L7 facilitate [fE'siliteit] vt. 帮助 L6facility[fE'siliti] n. 设备 L4facing[feisiN] n. 端面车削 L5fall within 属于, 适合于L15fan[fAn] n.风扇 L7far from 毫不, 一点不, 远非 L9fatigue[fE'ti^] n.疲劳L1feasible ['fi:zEbl] a 可行的L18feature ['fi:tFE] n.特色, 特征 L7,17feed[fi:d] n.. 进给 L5feedback ['fi:dbAk] n. 反馈 L8female['fi:meil] a. 阴的, 凹形的L11ferrule['ferEl] n. 套管L14file system 文件系统 L9fitter['fitE] n.装配工, 钳工 L4fix[fiks] vt. 使固定, 安装, vi. 固定L11fixed half and moving half 定模和动模L11flat-panel technology 平面(显示)技术 L9 flexibility[fleksi'biliti] n. 适应性, 柔性 L9 flexible['fleksEbl] a. 柔韧的L13flow mark 流动斑点L13follow-on tool 连续模L18foregoing ['fC:'^EuiN]adj. 在前的,前面的L8foretell[fC:'tell] vt. 预测, 预示, 预言 L9forge[fC:dV] n. v. 锻造 L3forming[fC:miN] n. 成型 L3four screen quadrants 四屏幕象限 L9 fracture['frAktFE] n.破裂L21free from 免于L21Ggap[^Ap] n. 裂口, 间隙L10gearbox['^iEbCks] n.齿轮箱 L5general arrangement L16govern['^QvEn] v.统治, 支配, 管理L13grain [^rein] n. 纹理L20graphic ['^rAfik] adj. 图解的 L6grasp [^rAsp] vt. 抓住 L8grid[^rid] n. 格子, 网格L16grind[^raind] v. 磨, 磨削, 研磨 L3grinding ['^raindiN] n. 磨光,磨削 L3,20 grinding machine 磨床 L5gripper[^ripE] n. 抓爪, 夹具 L9groove[^ru:v] n. 凹槽L12guide bush 导套 L5guide pillar 导柱 L5guide pillars and bushes 导柱和导套L11Hhandset['hAndset] n. 电话听筒 L4hardness['ha:dnis] n.硬度L1,2hardware ['ha:dwZE] n. 硬件 L6headstock['hedstCk] n.床头箱, 主轴箱 L5 hexagonal[hek'sA^Enl] a. 六角形的, 六角的L11 hindrance['hindrEns] n.障碍, 障碍物 L11hob[hCb] n. 滚刀, 冲头 L4hollow-ware 空心件L21horizontal[hCri'zCntl] a. 水平的L16hose[hEuz] n. 软管, 水管L13hyperbolic [haipE'bClik] adj.双曲线的 L7Ii.e. (id est) [拉] 也就是L12identical[ai'dentikl] a同样的L16identify [ai'dentifai] v. 确定, 识别 L7idle ['aidl] adj.空闲的 L8immediately[i'mi:djEtli] adv. 正好, 恰好L12 impact['impAkt] n.冲击L1impart [im'pa:t] v.给予 L11,17implement ['implimEnt] vt 实现 L6impossibility[impCsE'biliti] n.不可能L21 impression[im'preFEn] n. 型腔L11in contact with 接触L1in terms of 依据L1inasmuch (as)[inEz'mQtF] conj.因为, 由于 L3inch-to-metric conversions 英公制转换 L7 inclinable [in'klainEbl] adj. 可倾斜的L20inclusion [in'kluFEn] n. 内含物L19 inconspicuous[inkEn'spikjuEs] a. 不显眼的L14 incorporate [in'kC:pEreit] v 合并,混合L17 indentation[7inden'teiFEn ] n.压痕L1indenter[in'dentE] n. 压头L1independently[indi'peinEntli] a. 独自地, 独立地L16 inevitably[in'evitEbli] ad. 不可避免地L14 inexpensive[inik'spensiv]adj. 便宜的 L2 inherently [in'hiErEntli] adv.固有的 L7injection mould 注塑模L11injection[in'dVekFEn] n. 注射L11in-line-of-draw 直接脱模L14insert[in'sE:t] n. 嵌件L16inserted die 嵌入式凹模L19inspection[in'spekFEn] n.检查,监督 L9 installation[instE'leiFEn] n. 安装L10integration [inti'^reiFEn] n.集成 L6intelligent[in'telidVEnt]a. 智能的 L9 intentinonally [in'tenFEnEli] adv 加强地，集中地L17 interface ['intEfeis] n.. 界面 L6internal[in'tE:nl] a. 内部的L1,5interpolation [intEpE'leiFEn] n.插值法 L7 investment casting 熔模铸造 L4irregular [i'regjulE] adj. 不规则的，无规律L17 irrespective of 不论, 不管L11irrespective[iri'spektiv] a. 不顾的, 不考虑的L11 issue ['isju] vt. 发布，发出 L6Jjoint line 结合线L14Kkerosene['kerEsi:n] n.煤油L10keyboard ['ki:bC:d ] n. 健盘 L6knock [nRk] v 敲，敲打L17Llance [la:ns] v. 切缝L19lathe[leiT] n. 车床 L4latitude ['lAtitju:d] n. 自由L17lay out 布置L13limitation[limi'teiFEn] n.限度,限制,局限(性) L3local intelligence局部智能 L9locate [lEu'keit] vt. 定位L18logic ['lCdVik] n. 逻辑 L7longitudinal['lCndVE'tju:dinl] a. 纵向的 L5longitudinally['lCndVE'tju:dinl] a. 纵向的L13look upon 视作, 看待L17lubrication[lju:bri'keiFEn ] n.润滑L21Mmachine shop 车间 L2machine table 工作台 L8machining[mE'Fi:niN] n. 加工 L3made-to-measure 定做L15maintenance['meintinEns] n.维护,维修 L7majority[mE'dVa:riti] n.多数L21make use of 利用 L2male[meil] a. 阳的, 凸形的L11malfunction['mAl'fQNFEn] n. 故障 L9mandrel['mAdtil] n.心轴L22manifestation[mAnifEs'teiFEn] n. 表现, 显示 L9 massiveness ['mAsivnis ] 厚实，大块 L19measure['meVE] n. 大小, 度量L1microcomputer 微型计算机 L9microns['maikrCn] n.微米L10microprocessor 微处理器 L9mild steel 低碳钢L17milling machine 铣床 L4mineral['minErEl] n.矿物, 矿产 L2minimise['minimaiz] v.把···减到最少, 最小化L13minute['minit] a.微小的L10mirror image 镜像L16mirror['mirE] n. 镜子L16MIT (Massachusetts Institute of Technology) 麻省理工学院 L7 moderate['mCdErit]adj. 适度的L1,2modification [mRdifi'keiFEn ] n. 修改, 修正 L6modulus['mCdjulEs] n.系数L1mold[mEuld] n. 模, 铸模, v. 制模, 造型 L3monitor ['mCnitE ] v. 监控 L6monograph['mCnE^ra:f] n. 专著 L4more often than not 常常 L20motivation[mEuti'veiFEn] n. 动机 L9mould split line 模具分型线L12moulding['mEudiN] n. 注塑件 L5,11move away from 抛弃L17multi-imprssion mould 多型腔模L12Nnarrow['nArEu] a. 狭窄的L12NC (numerical control ) 数控 L7nevertheless[7nevETE'les] conj.,adv.然而,不过L11 nonferrous['nCn'ferEs] adj.不含铁的, 非铁的 L2 normally['nC:mli]adv.通常地L22novice['nCvis] n. 新手, 初学者L16nozzle['nCzl] n. 喷嘴, 注口L12numerical [nju'merikl] n. 数字的 L6Oobjectionable [Eb'dVekFEbl] adj. 有异议的，讨厌的L17 observe[Eb'zE:v] vt. 观察 L2obviously ['CbviEsli] adv 明显地L17off-line 脱机的 L6on-line 联机 L9operational [CpE'reiFEnl] adj.操作的, 运作的 L8 opportunity[CpE'tju:niti] n. 时机, 机会L13 opposing[E'pEuziN] a.对立的, 对面的L12opposite['CpEzit] n. 反面 L1 a.对立的,对面的 L12 optimization [Rptimai'zeiFEn] n.最优化 L6orient ['C:riEnt] vt. 确定方向 L8orthodox ['C:WEdCks] adj. 正统的，正规的L19 overall['EuvErC:l] a.全面的,全部的 L8,13overbend v.过度弯曲L20overcome[EuvE'kQm] vt.克服, 战胜L10overlaping['EuvE'lApiN] n. 重叠 L4overriding[EuvE'raidiN] a. 主要的, 占优势的L11Ppack[pAk] v. 包装 L2package ['pAkidV] vt.包装 L7pallet ['pAlit] n.货盘 L8panel ['pAnl] n.面板 L7paraffin['pArEfin] n. 石蜡L10parallel[pArElel] a.平行的 L5penetration[peni'treiFEn ] n.穿透L1peripheral [pE'rifErEl] adj 外围的 L6periphery [pE'rifEri] n. 外围L18permit[pE'mit] v. 许可, 允许L16pessure casting 压力铸造 L4pillar['pilE] n. 柱子, 导柱 L5,17pin[pin] n. 销, 栓, 钉 L5,17pin-point gate 针点式浇口L12piston ['pistEn] n.活塞L1plan view 主视图L16plasma['plAzmE] n. 等离子 L9plastic['plAstik] n. 塑料 L3platen['plAtEn] n. 压板L12plotter[plCtE] n. 绘图机 L9plunge [plQndV] v翻孔L18plunge[plQndV] v.投入 L2plunger ['plQndVE ] n. 柱塞L19pocket-size 袖珍 L9portray[pC:'trei] v.描绘L21pot[pCt] n.壶L21pour[pC:] vt. 灌, 注L22practicable['prAktikEb] a. 行得通的L14 preferable['prefErEbl] a.更好的, 更可取的 L3 preliminary [pri'liminEri] adj 初步的，预备的L19 press setter 装模工L17press[pres] n.压,压床,冲床,压力机 L2,8 prevent [pri'vent] v. 妨碍L20primarily['praimErili] adv.主要地 L4 procedure[prE'si:dVE] n.步骤, 方法, 程序 L2,16 productivity.[prEudQk'tiviti] n. 生产力 L9profile ['prEufail] n.轮廓L10progressively[prE'^resiv] ad.渐进地L15 project[prE'dVekt] n.项目 L2project[prE'dVekt] v. 凸出L11projection[prE'dVekFEn] n.突出部分L21 proper['prCpE] a. 本身的L10property['prCpEti] n.特性L1prototype ['prEutEtaip] n. 原形 L7proximity[prCk'simiti] n.接近 L9prudent['pru:dEnt] a. 谨慎的L16punch [pQntF] v. 冲孔 L3punch shapper tool 刨模机L17punch-cum-blanking die 凹凸模L18punched tape 穿孔带 L3purchase ['pE:tFEs] vt. 买，购买 L6push back pin 回程杆 L5pyrometer[pai'nCmitE] n. 高温计 L2Qquality['kwaliti] n. 质量L1,3quandrant['kwCdrEnt] n. 象限 L9quantity ['kwCntiti] n. 量，数量L17quench[kwentF] vt. 淬火 L2Rradial['reidiEl] adv.放射状的L22ram [rAm] n 撞锤. L17rapid['rApid]adj. 迅速的 L2rapidly['rApidli]adv. 迅速地 L1raster['rAstE] n. 光栅 L9raw [rC:] adj. 未加工的 L6raw material 原材料 L3ream [ri:m] v 铰大L17reaming[ri:miN] n. 扩孔, 铰孔 L8recall[ri'kC:l] vt. 记起, 想起L13recede [ri'si:d] v. 收回, 后退L20recess [ri'ses] n. 凹槽,凹座,凹进处 L4,18 redundancy[ri'dQndEnsi] n. 过多 L9re-entrant 凹入的L12refer[ri'fE:] v. 指, 涉及, 谈及 L1,12reference['refErEns] n.参照,参考L21refresh display 刷新显示 L9register ring 定位环L11register['redVstE] v. 记录, 显示, 记数 L2regrind[ri:'^aind](reground[ri:'gru:nd]) vt. 再磨研L12 relative['relEtiv] a. 相当的, 比较的L12relay ['ri:lei] n. 继电器 L7release[ri'li:s] vt. 释放 L1relegate['relE7geit] vt. 把··降低到 L9reliability [rilaiE'biliti] n. 可靠性 L7relief valves 安全阀L22relief[ri'li:f] n.解除L22relieve[ri'li:v ]vt.减轻, 解除 L2remainder[ri'meindE] n. 剩余物, 其余部分 L4 removal[ri'mu:vl] n. 取出L14remove[ri'mu:v] v. 切除, 切削 L4reposition [ripE'ziFEn] n.重新安排L17represent[7repri'zentE] v 代表,象征L11reputable['repjutEbl] a. 有名的, 受尊敬的L15 reservoir['rezEvwa: ] n.容器, 储存器L22resident['rezidEnt] a. 驻存的 L9resist[ri'zist] vt.抵抗L1resistance[ri'zistEns] n.阻力, 抵抗 L1resolution[7rezE'lu:FEn] n. 分辨率 L9respective[ri'spektiv] a.分别的,各自的 L11respond[ris'pCnd] v.响应, 作出反应 L9 responsibility[rispCnsE'biliti] n.责任L13restrain[ris'trein]v.抑制L21restrict [ris'trikt] vt 限制，限定L18restriction[ris'trikFEn] n. 限制L12retain[ri'tein] vt.保持, 保留 L2,12retaining plate 顶出固定板L16reveal [ri'vil] vt.显示，展现L17reversal [ri'vEsl] n. 反向 L1,20right-angled 成直角的L20rigidity[ri'dViditi] n. 刚度 L1rod[rCd] n. 杆, 棒L1,5rotate['rEuteit] vt.(使)旋转 L5rough machining 粗加工 L5rough[rQf] a. 粗略的 L5,21routine [ru:'ti:n] n. 程序 L7rubber['rQbE] n.橡胶 L3,22runner and gate systems 流道和浇口系统L11Ssand casting 砂型铸造 L3satisfactorily[7sAtis'fAktrili] adv. 满意地L1saw[aC:] n. 锯子 L4scale[skeil]n. 硬壳 L2score[skC:] v. 刻划L14scrap[skrAp] n.废料, 边角料, 切屑 L2,3 screwcutting 切螺纹 L4seal[si:l] vt.密封L22secondary storage L9section cutting plane 剖切面L16secure[si'kjuE] v.固定L22secure[si'kjuE] vt.紧固,夹紧,固定 L5,22 segment['se^mEnt] v. 分割L10sensitive['sensitiv]a.敏感的L1,7sequence ['si:kwEns] n. 次序 L6sequential[si'kwenFEl] a.相继的L16seriously['siEriEsli] adv.严重地L1 servomechanism ['sE:vE'mekEnizm] n.伺服机构 L7 Servomechanism Laboratoies 伺服机构实验室 L7 servomotor ['sE:vEmEutE] n.伺服马达 L8setter ['setE] n 安装者L17set-up 机构L20sever ['sevE] v 切断L17severity [si'veriti] n. 严重L20shaded[FAdid] adj.阴影的L21shank [FANk] n. 柄. L17shear[FiE]n.剪,切L1shot[FCt] n. 注射L12shrink[FriNk] vi. 收缩L11side sectional view 侧视图L16signal ['si^nl] n.信号 L8similarity[simi'lAriti] n.类似L15simplicity[sim'plisiti] n. 简单L12single-point cutting tool 单刃刀具 L5situate['sitjueit] vt. 使位于, 使处于L11slide [slaid] vi. 滑动, 滑落L20slideway['slaidwei] n. 导轨 L5slot[slCt] n. 槽 L4slug[slQ^] n. 嵌条L12soak[sEuk] v. 浸, 泡, 均热 L2software ['sCftwZE] n. 软件 L6solid['sClid] n.立体, 固体 L9solidify[sE'lidifai] vt.vi. (使)凝固, (使)固化L13 solution[sE'lu:FEn] n.溶液L2sophisiticated [sE'fistikeitid] adj.尖端的,完善的 L8 sound[saund] a. 结实的, 坚固的) L1spark erosion 火花蚀刻L10spindle['spindl] n. 主轴L5,8spline[splain] n.花键 L4split[split] n. 侧向分型, 分型 L12,14spool[spu:l] n. 线轴L14springback n.反弹L20spring-loaded 装弹簧的L18sprue bush 主流道衬套L11sprue puller 浇道拉杆L12square[skwZE] v. 使成方形 L4stage [steidV] n. 阶段 L16,19 standardisation[7stAndEdai'zeiFEn] n. 标准化L15 startling['sta:tliN] a. 令人吃惊的L10steadily['stedEli ] adv. 稳定地L21step-by-step 逐步 L8stickiness['stikinis] n.粘性L22stiffness['stifnis] n. 刚度L1stock[stCk] n.毛坯, 坯料 L3storage tube display 储存管显示 L9storage['stC:ridV] n. 储存器 L9 straightforward[streit'fC:wEd]a.直接的 L10strain[strein] n.应变L1strength[streNW] n.强度L1stress[stres] n.压力,应力L1stress-strain应力--应变 L6stretch[stretF] v.伸展 L1,21strike [straik] vt. 冲击L20stringent['strindVEnt ] a.严厉的L22stripper[stripE] n. 推板L15stroke[strouk] n. 冲程, 行程L12structrural build-up 结构上形成的L11sub-base 垫板L19subject['sQbdVikt] vt.使受到L21submerge[sEb'mE:dV] v.淹没L22subsequent ['sQbsikwent] adj. 后来的L20subsequently ['sQbsikwentli] adv. 后来, 随后 L5substantial[sEb'stAnFEl] a. 实质的L10substitute ['sQbstitju:t] vt. 代替,.替换 L7subtract[sEb'trAkt] v.减, 减去L15suitable['su:tEbl] a. 合适的, 适当的 L5suitably['su:tEbli] ad.合适地L15sunk[sQNk](sink的过去分词) v. 下沉, 下陷 L11superior[sE'piEriE] adj.上好的L22susceptible[sE'septEbl] adj.易受影响的 L7sweep away 扫过L17symmetrical[si'metrikl] a. 对称的 L14synchronize ['siNkrEnaiz] v.同步,同时发生L8Ttactile['tAktail] a. 触觉的, 有触觉的 L9tailstock['teilstCk] n.尾架 L5tapered['teipEd] a. 锥形的L12tapping['tApiN] n. 攻丝 L8technique[tek'ni:k] n. 技术L16tempering['tempErN] n.回火 L2tendency['tendEnsi] n. 趋向, 倾向 L13tensile['tensail] a.拉力的, 可拉伸的 L2 拉紧的, 张紧的 L1 tension ['tenFEn] n.拉紧,张紧L1terminal ['tE:mEnl ] n. 终端机 L6terminology[tE:mi'nClEdVi ] n. 术语, 用辞L11theoretically [Wi:E'retikli ] adv.理论地L21thereby['TZEbai] ad. 因此, 从而L15thermoplastic['WE:mEu'plAstik] a. 热塑性的, n. 热塑性塑料 L3 thermoset['WE:mEset] n.热固性L12thoroughly['WQrEuli] adv.十分地, 彻底地 L2thread pitch 螺距 L5thread[Wred] n. 螺纹 L5thrown up 推上L17tilt [tilt] n. 倾斜, 翘起L20tolerance ['tClErEns] n..公差L17tong[tCN] n. 火钳 L2tonnage['tQnidV] n.吨位, 总吨数 L3tool point 刀锋 L3tool room 工具车间L10toolholder['tu:lhEuldE] n.刀夹,工具柄 L5toolmaker ['tu:l'meikE] n 模具制造者 L17toolpost grinder 工具磨床 L4toolpost['tu:l'pEust] n. 刀架 L4torsional ['tC:FEnl] a扭转的 . L1toughness['tCfnis] n. 韧性 L2trace [treis] vt.追踪 L7tracer-controlled milling machine 仿形铣床 L4 transverse[trAns'vE:s] a. 横向的 L5tray [trei] n. 盘，盘子，蝶L19treatment['tri:tmEnt] n.处理L2tremendous[tri'mendEs] a. 惊人的, 巨大的 L9 trend [trend] n.趋势 L7trigger stop 始用挡料销L17tungsten['tQNstEn] n.钨 L10turning['tE:niN] n.车削 L4,5twist[twist ] v.扭曲，扭转L1two-plate mould 双板式注射模L12Uultimately['Qltimitli] adv终于. L6undercut moulding 侧向分型模L14undercut['QndEkQt] n. 侧向分型L14undercut['QndEkQt] n.底切L12underfeed['QndE'fi:d] a, 底部进料的L15 undergo[QndE'^Eu] vt.经受L1underside['QndEsaid] n 下面,下侧L11undue[Qn'dju:] a.不适当的, 过度的 L4,10 uniform['ju:nifC:m] a.统一的, 一致的L12utilize ['ju:tilaiz] v 利用L17Utopian[ju'tEupiEn] adj.乌托邦的, 理想化的L21Vvalve[vAlv] n.阀L22vaporize['veipEraiz] vt.vi. 汽化, (使)蒸发L10 variation [vZEri'eiFEn] n. 变化L20various ['vZEriEs] a.不同的,各种的 L1,20vector feedrate computation 向量进刀速率计算 L7 vee [vi:] n. v字形L20velocity[vi'lCsiti] n.速度L1versatile['vEsEtail] a.多才多艺的,万用的 L5,8 vertical['vE:tikl] a. 垂直的L16via [vaiE] prep.经,通过 L8vicinity[vE'siniti] n.附近L13viewpoint['vju:pCint] n. 观点 L4Wwander['wCndE] v. 偏离方向L13warp[wC:p] v. 翘曲 L2washer ['wCFE] n. 垫圈L18wear [wZE] v.磨损 L7well line 结合线L13whereupon [hwZErE'pCn] adv. 于是L19winding ['waindiN] n. 绕, 卷 L8with respect to 相对于L1,5withstand[wiT'stAnd] vt.经受,经得起 L1work[wE:k] n. 工件 L4workstage 工序L19wrinkle['riNkl] n.皱纹vt.使皱L21Yyield[ji:ld] v. 生产 L9Zzoom[zu:] n. 图象电子放大 L9GLOSSARYAabrasive grinding 强力磨削 L3abrasive[E'breisiv] a.磨料的, 研磨的 L2,3 absence ['AbsEns] n.. 不在，缺席L17 accesssory[Ak'sesEri] n.附件L10 accommodate[E'kCmEdeit] v. 适应 L5 accordingly[E'kC:diNli] adv.因此,从而,相应地 L7,13 accuracy['AkjurEsi] n精度,准确性L1,3actuate['Aktjueit] vt.开动(机器), 驱动 L8 adequate['Adikwit] a. 足够的L13adhesive[Ed'hi:siv] n. 粘合剂L22adjacent[E'dVeisnt] a. 邻近的L13adopt[E'dCpt] vt. 采用 L4advance [Ed'vA:ns] n.进步 L7advisable [Ed'vaizbl] adj. 可取的L20agitate['AdViteit] v. 摇动 L2a large extent 很大程度 L4,13algorithm ['Al^EriTEm] n. 算法 L6align [E'lain] v 定位，调准L17alignment[E'lainmEnt] n. 校直L11all-too-frequent 频繁L17allowance[E'lEuens] n. 容差, 余量 L5alternate['C:ltEnit]v.交替,轮流L1alternative[C:l'tE:nEtiv] n. 替换物 L3 alternatively[C:l'tE:nEtivli] ad. 做为选择, 也许 L5 aluminiun[7Alju'minjEm] n.铝 L2ample['Ampl] adj. 充足的L20analysis [E'nAlEsis] n. 分析 L6ancillary['AnsilEri] a.补助的, 副的 L4angular ['A^julE] adj. 有角的L20annealing[E'li:liN] n.退火 L2aperture ['ApEtFE] n.孔L17applied loads 作用力L1appropriate [E'prEuprieit] a. 适当的 L6,20arc[a:k] n.弧, 弓形L10arise[E'raiz] vi. 出现, 发生L21arrange[E'reidV] v. 安排L12article['a:tikl] n.制品, 产品L21ascertain[7AsE'tein] vt. 确定, 查明L1 assemble[E'sembl] vt.组装 L4attitude ['Atitju:d] n 态度L17auxiliary [C:^'ziljEri]adj. 辅助的 L8avoid[E'vCid] v.避免 L7axis['Aksis] n.轴 L5axle['Aksl] n.轮轴, 车轴L1Bbackup['bAk7Qp] n. 备份 L9batch [bAtF] n 一批L17bearing['bZEriN] n.轴承,支座L21bed[bed] n. 床身 L5behavior[bi'heivjE] n. 性能L1bench-work 钳工工作 L4bend[bend] v.弯曲L1beneath[bi'ni:W] prep在···下 L4bin [bin] n. 仓，料架L19blank [blANk] n. 坯料L20blank [blANk] v. 冲裁,落料L17blanking tool 落料模L17blast [blQst] n.一阵（风）L18blemish['blemiF] n. 缺点, 污点L13bolster['bEulstE] n. 模座,垫板 L4,5boost[bu:st] n. 推进 L9boring['bC:riN] n.镗削, 镗孔L4,5bracket ['brAkit] n. 支架L19brass [brAs] n.黄铜 L2break down 破坏L1breakage ['breikidV] n.破坏L17bridge piece L16brine[brain] n. 盐水 L2brittle['britl] adv.易碎的L1buffer [bQfE] n.缓冲器 L8built-in 内装的 L9bulging [bQldViN] n. 凸肚L22burr [bE:] n. 毛刺L17bush [buF] n. 衬套L17bush[buF]n. 衬套 L5by far (修饰比较级, 最高级)···得多, 最 L3 by means of 借助于 L5Ccabinet ['kAbinit] n.橱柜 L7call upon 要求L17carbide['ka:baid] n.碳化物L10carburzing['ka:bjuretiN] n. 渗碳 L2carriage['kAridV] n.拖板, 大拖板 L5carry along 一起带走L18carry down over 从···上取下L21carry out 完成L17case hardening 表面硬化 L2case[keis] n. 壳, 套 L2cast steel 铸钢L17casting['ka:stiN] n. 铸造,铸件 L3category['kAtE^Euri] n. 种类 L6,15caution ['kC:FEn] n. 警告，警示L17cavity and core plates 凹模和凸模板L11 cavity['kAviti] n.型腔, 腔, 洞 L4,10centre-drilling 中心孔 L5ceramic[si'rAmik] n.陶瓷制品 L3chain doted line 点划线L11channel['tFAnl] n.通道, 信道 L8 characteristic[kArEktE'ristik] n.特性L1check[tFek] v.核算L21chip[tFip] n.切屑, 铁屑 L3chuck [tFQk] n.卡盘L5,8chute [Fu:t] n. 斜道L19circa ['sEkE:] adv. 大约 L7circlip['sE:klip] n.(开口)簧环L22circuit['sE:kit] n. 回路, 环路L13circular supoport block L5circulate['sE:kjuleid] v.(使)循环L13clamp [klAmp] vt 夹紧L17clamp[klAmp] n.压板L12clay[klei] n. 泥土L2,7clearance ['kliErEns] n. 间隙L17clip [klip] vt. 切断，夹住L19cold hobbing 冷挤压 L4cold slug well 冷料井L12collapse[kE'lAps] vi.崩塌, 瓦解L22 collapsible[kE'lApsEbl] adj.可分解的L22 combination [kCmbi'neiFEn] n. 组合L18 commence[kE'mens] v. 开始, 着手L16 commence[kE'mens]v. 开始L21 commercial [kE'mE:FEl] adj. 商业的 L7 competitive[kEm'petitiv] a. 竞争的 L9 complementary[7kCmpli'mentEri] a. 互补的 L5 complexity [kem'pleksiti] n.复杂性 L8 complicated['kCmplEkeitid] adj.复杂的 L2 complication [kCmpli'keiFEn] n. 复杂化 L5,20 compression [kEm'preFEn] n.压缩L1。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：spray diameter流道: runner热流道：hot runner, hot manifold 热嘴冷流道: hot spray/cold runner唧嘴直流: direct spray gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot spray热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug 模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar slot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin 模具专业英语推板：stripper plate缩呵：movable core, return core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜楔：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.Binjection nozzle 射出喷嘴顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability, stable 强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolerance铜公(电极)：copper electrodebrasive grinding 强力磨削abrasive 磨料的,研磨的absence 不在，缺席accessory 附件accommodate 适应accordingly 因此,从而,相应地accuracy 精度,准确性actuate 开动(机器),驱动adequate 足够的adhesive 粘合剂adjacent 邻近的adopt 采用advance 进步advisable 可取的agitate 摇动a large extent 很大程度algorithm 算法align 定位，调准alignment 校直all-too-frequent 频繁allowance 容差,余量alternate 交替,轮流alternatively 选择,也许aluminium 铝ample 充足的analysis 分析ancillary 补助的,副的angular 有角的annealing 退火aperture 孔applied loads 作用力appropriate 适当的arc 弧,弓形arise 出现,发生arrange 安排article 制品,产品ascertain 确定,查明assemble 组装attitude 态度auxiliary 辅助的avoid 避免axis 轴axle 轮轴,车轴alternative 替换物backup 备份batch 一批bearing 轴承,支座bed 床身behavior 性能bench-work 钳工工作bend 弯曲beneath 在•••下bin 仓，料架blank 坯料blank 冲裁,落料blanking 落料模blast 一阵（风）blemish 缺点,污点bolster 模座,垫板boring 镗削,镗孔bracket 支架brass 黄铜break down 破坏breakage 破坏brine 盐水brittle 易碎的buffer 缓冲器built-in 内装的bulging 凸肚burr 毛刺bush 衬套by far •••得多,最by means of 借助于boost 推进cabinet 橱柜call upon 要求carbide 碳化物carburzing 渗碳carriage 拖板,大拖板carry along 一起带走carry down over 从•••上取下carry out 完成case hardening 表面硬化case 壳,套cast steel 铸钢casting 铸造,铸件category 种类caution 警告，警示cavity and core plates 凹模和凸模板cavity 型腔,腔,洞centre-drilling 中心孔ceramic 陶瓷制品chain doted line 点划线channel 通道,信道characteristic 特性check 核算chip 切屑,铁屑chuck 卡盘chute 斜道circa 大约circlip (开口)簧环circuit 回路,环路circulate (使)循环clamp 夹紧clamp 压板clay 泥土clearance 间隙clip 切断，夹住cold hobbing 冷挤压cold slug well 冷料井collapse 崩塌,瓦解collapsible 可分解的combination 组合commence 开始,着手commence 开始commercial 商业的competitive 竞争的complementary 互补的complexity 复杂性complication 复杂化compression 压缩comprise 包含compromise 妥协,折衷concern with 关于concise 简明的,简练的confront 使面临connector 连接口,接头consequent 随之发生的,必然的console 控制台consume 消耗,占用consummate 使完善container 容器contingent 可能发生的CPU (central processing unit) 中央处理器conventional 常规的converge 集中于一点conversant 熟悉的conversion 换算,转换conveyer 运送装置coolant 冷却液coordinate (使)协调copy machine 仿形(加工)机床core 型芯,核心corresponding 相应的counteract 反作用,抵抗couple with 伴随contour 轮廓crack （使）破裂，裂纹critical 临界的cross-hatching 剖面线cross-section drawn 剖面图cross-slide 横向滑板CRT (cathoder-ray tube) 阴极射线管crush 压碎cryogenic 低温学的crystal 结晶状的cubic 立方的,立方体的cup (使)成杯状,引伸curable 可矫正的curvature 弧线curve 使弯曲cutter bit 刀头,刀片cyanide 氰化物complicated 复杂的dash 破折号daylight 板距decline 下落,下降,减少deform (使)变形demonstrate 证明depict 描述deposite 放置depression 凹穴descend 下降desirable 合适的detail 细节，详情deterioration 退化,恶化determine 决定diagrammmatic 图解的，图表的dictate 支配die 模具,冲模,凹模dielectric 电介质die-set 模架digital 数字式数字dimensional 尺寸的,空间的discharge 放电,卸下,排出discharge 卸下discrete 离散的,分立的dislodge 拉出,取出dissolution 结束distinct 不同的，显著的distort 扭曲distort (使)变形,扭曲distributed system 分布式系统dowel 销子dramaticlly 显著地drastic 激烈的draughting 绘图draughtsman 起草人drawing 制图drill press 钻床drum 鼓轮dual 双的，双重的ductility 延展性dynamic 动力的edge 边缘e.g.(exempli gratia) [拉]例如ejector 排出器ejector plate 顶出板ejector rob 顶杆elasticity 弹性electric dicharge machining 电火花加工electrode 电极electro-deposition 电铸elementary 基本的eliminate 消除,除去elongate (使)伸长,延长emerge 形成,显现emphasise 强调endeavour 尽力engagement 约束,接合enhance 提高,增强ensure 确保，保证erase 抹去,擦掉evaluation 评价,估价eventually 终于evolution 进展excecution 执行,完成execute 执行electrochemical machining 电化学加工exerte 施加experience 经验explosive 爆炸(性)的extend 伸展external 外部的extract 拔出extreme 极端extremely 非常地extremity 极端extrusion 挤压,挤出envisage 设想Fahrenheit 华氏温度fabricate 制作,制造flat-panel technology 平面(显示)技术facility 设备facing 端面车削fall within 属于,适合于fan 风扇far from 毫不,一点不,远非fatigue 疲劳feasible 可行的feature 特色,特征feed 进给feedback 反馈female 阴的,凹形的ferrule 套管file system 文件系统fitter 装配工,钳工fix 使固定,安装fixed half and moving half 定模和动模facilitate 帮助flexibility 适应性,柔性flexible 柔韧的flow mark 流动斑点follow-on tool 连续模foregoing 在前的,前面的foretell 预测,预示,预言forge 锻造forming 成型four screen quadrants 四屏幕象限fracture 破裂free from 免于gap 裂口,间隙gearbox 齿轮箱govern 统治,支配,管理grain 纹理graphic 图解的grasp 抓住grid 格子,网格grind 磨,磨削,研磨grinding 磨光,磨削grinding machine 磨床gripper 抓爪,夹具groove 凹槽guide bush 导套guide pillar 导柱guide pillars and bushes 导柱和导套handset 电话听筒hardness 硬度hardware 硬件headstock 床头箱,主轴箱hexagonal 六角形的,六角的hindrance 障碍,障碍物hob 滚刀,冲头hollow-ware 空心件horizontal 水平的hose 软管,水管hyperbolic 双曲线的i.e. (id est) [拉]也就是identical 同样的identify 确定,识别idle 空闲的immediately 正好,恰好impact 冲击impart 给予implement 实现impossibility 不可能impression 型腔in contact with 接触in terms of 依据inasmuch (as) co因为,由于inch-to-metric conversions 英公制转换inclinable 可倾斜的inclusion 内含物inconspicuous 不显眼的incorporate 合并,混合indentation 压痕indenter 压头independently 独自地,独立地inevitably 不可避免地inexpensive 便宜的inherently 固有的injection mould 注塑模injection 注射in-line-of-draw 直接脱模insert 嵌件inserted die 嵌入式凹模inspection 检查,监督installation 安装integration 集成intelligent 智能的intentinonally 加强地，集中地interface 界面internal 内部的interpolation 插值法investment casting 熔模铸造irregular 不规则的，无规律irrespective of 不论,不管irrespective 不顾的,不考虑的issue 发布，发出joint line 结合线kerosene 煤油keyboard 健盘knock 敲，敲打lance 切缝lathe 车床latitude 自由lay out 布置limitation 限度,限制,局限(性) local intelligence 局部智能locate 定位logic 逻辑longitudinal 纵向的longitudinally 纵向的look upon 视作,看待lubrication 润滑machine shop 车间machine table 工作台machining 加工made-to-measure 定做maintenance 维护,维修majority 多数make use of 利用male 阳的,凸形的malfunction 故障mandrel 心轴manifestation 表现,显示massiveness 厚实，大块measure 大小,度量microcomputer 微型计算机microns 微米microprocessor 微处理器mild steel 低碳钢milling machine 铣床mineral 矿物,矿产minimise 把减到最少,最小化minute 微小的mirror image 镜像mirror 镜子moderate 适度的modification 修改,修正modulus 系数mold 模,铸模mold 制模,造型monitor 监控monograph 专著more often than not 常常motivation 动机mould split line 模具分型线moulding 注塑件move away from 抛弃multi-imprssion mould 多型腔模narrow 狭窄的NC (numerical control) 数控nevertheless 然而,不过nonferrous 不含铁的,非铁的normally 通常地novice 新手,初学者nozzle 喷嘴,注口numerical 数字的objectionable 有异议的，讨厌的observe 观察obviously 明显地off-line 脱机的on-line 联机operational 操作的,运作的opportunity 时机,机会opposing 对立的,对面的opposite 反面optimization 最优化orient 确定方向orthodox 正统的，正规的overall 全面的,全部的overbend 过度弯曲overcome 克服,战胜overlaping 重叠overriding 主要的,占优势的opposite 对立的,对面的pack 包装package 包装pallet 货盘panel 面板paraffin 石蜡parallel 平行的penetration 穿透peripheral 外围的periphery 外围permit 许可,允许pessure casting 压力铸造pillar 柱子,导柱pin 销,栓,钉pin-point gate 针点式浇口piston 活塞plan view 主视图plasma 等离子plastic 塑料platen 压板plotter 绘图机plunge 翻孔plunge 投入plunger 柱塞pocket-size 袖珍portray 描绘pot 壶pour 灌,注practicable 行得通的preferable 更好的,更可取的preliminary 初步的，预备的press setter 装模工press 压,压床,冲床,压力机prevent 妨碍primarily 主要地procedure 步骤,方法,程序productivity 生产力profile 轮廓progressively 渐进地project 项目project 凸出projection 突出部分proper 本身的property 特性prototype 原形proximity 接近prudent 谨慎的punch 冲孔punch shapper tool 刨模机punch-cum-blanking die 凹凸模punched tape 穿孔带purchase 买，购买push back pin 回程杆pyrometer 高温计quality 质量quandrant 象限quantity 量，数量quench 淬火radial 放射状的ram 撞锤rapid 迅速的rapidly 迅速地raster 光栅raw 未加工的raw material 原材料ream 铰大reaming 扩孔,铰孔recall 记起,想起recede 收回,后退recess 凹槽,凹座,凹进处redundancy 过多re-entrant 凹入的refer 指,涉及,谈及reference 参照,参考refresh display 刷新显示register ring 定位环register 记录,显示,记数regrind 再磨研relative 相当的,比较的relay 继电器release 释放relegate 把降低到reliability 可靠性relief valves 安全阀relief 解除relieve 减轻,解除remainder 剩余物,其余部分removal 取出remove 切除,切削reposition 重新安排represent 代表,象征reputable 有名的,受尊敬的reservoir 容器,储存器resident 驻存的resist 抵抗resistance 阻力,抵抗resolution 分辨率respective 分别的,各自的respond 响应,作出反应responsibility 责任restrain 抑制restrict 限制，限定restriction 限制retain 保持,保留retaining plate 顶出固定板reveal 显示，展现reversal 反向right-angled 成直角的rigidity 钢度rod 杆,棒rotate (使)旋转rough machining 粗加工rough 粗略的routine 程序rubber 橡胶runner and gate systems 流道和浇口系统sand casting 砂型铸造satisfactorily 满意地saw 锯子scale 硬壳score 刻划scrap 废料,边角料,切屑screwcutting 切螺纹seal 密封section cutting plane 剖切面secure 固定secure 紧固,夹紧,固定segment 分割sensitive 敏感的sequence 次序sequential 相继的seriously 严重地servomechanism 伺服机构servomotor 伺服马达setter 安装者set-up 机构sever 切断severity 严重shaded 阴影的shank 柄shear 剪,切shot 注射shrink 收缩side sectional view 侧视图signal 信号similarity 类似simplicity 简单single-point cutting tool 单刃刀具situate 使位于,使处于slide 滑动,滑落slideway 导轨slot 槽slug 嵌条soak 浸,泡,均热software 软件solid 立体,固体solidify (使)凝固solidify (使)固化solution 溶液sophisiticated 尖端的,完善的sound 结实的,坚固的spark erosion 火花蚀刻spindle 主轴spline 花键split 侧向分型,分型spool 线轴springback 反弹spring-loaded 装弹簧的sprue bush 主流道衬套sprue puller 浇道拉杆square 使成方形Servomechanism Laboratoies 伺服机构实验室stage 阶段standardisation 标准化startling 令人吃惊的steadily 稳定地step-by-step 逐步stickiness 粘性stiffness 刚度stock 毛坯,坯料storage tube display 储存管显示storage 储存器straightforward 直接的strain 应变strength 强度stress 压力,应力stress-strain 应力--应变stretch 伸展strike 冲击stringent 严厉的stripper 推板stroke 冲程,行程structrural build-up 结构上形成的sub-base 垫板subject 使受到submerge 淹没subsequent 后来的subsequently 后来,随后substantial 实质的substitute 代替,替换subtract 减,减去suitable 合适的,适当的suitably 合适地sunk 下沉,下陷superior 上好的susceptible 易受影响的sweep away 扫过symmetrical 对称的synchronize 同步,同时发生tactile 触觉的,有触觉的tailstock 尾架tapered 锥形的tapping 攻丝technique 技术tempering 回火tendency 趋向,倾向tensile 拉力的,可拉伸的tension 拉紧,张紧terminal 终端机terminology 术语,用辞theoretically 理论地thereby 因此,从而thermoplastic 热塑性的thermoplastic 热塑性塑料thermoset 热固性thoroughly 十分地,彻底地thread pitch 螺距thread 螺纹thrown up 推上tilt 倾斜,翘起tolerance 公差two-plate mould 双板式注射模tong 火钳tonnage 吨位,总吨数tool point 刀锋tool room 工具车间toolholder 刀夹,工具柄toolmaker 模具制造者toolpost grinder 工具磨床toolpost 刀架torsional 扭转的toughness 韧性trace 追踪transverse 横向的tray 盘，盘子，蝶treatment 处理tremendous 惊人的,巨大的trend 趋势trigger stop 始用挡料销tungsten 钨turning 车削twist 扭曲，扭转tracer-controlled milling machine 仿形铣床ultimately 终于undercut mould 侧向分型模undercut 侧向分型undercut 底切underfeed 底部进料的undergo 经受underside 下面,下侧undue 不适当的,过度的uniform 统一的,一致的utilize 利用Utopian 乌托邦的,理想化的valve 阀vaporize 汽化vaporize (使)蒸发variation 变化various 不同的,各种的vector feedrate computation 向量进刀速率计算vee 字形velocity 速度versatile 多才多艺的,万用的vertical 垂直的via prep经,通过vicinity 附近viewpoint 观点wander 偏离方向warp 翘曲washer 垫圈wear 磨损well line 结合线whereupon 于是winding 绕,卷with respect to 相对于withstand 经受,经得起work 工件workstage 工序wrinkle 皱纹使皱yield 生产zoom 图象电子放大runner less mold 无流道模hot runner mold 热流道模insulated runner mold 绝热流道模warm runner mold 温流道模runner plate 流道板warm runner plate 温流道板sprue 直浇道，主流道，浇口runless injiection 无流道冷料模具hot-runner mold 热流道模具runner ejector set 流道顶出器runner lock pin 流道拉梢shoot 流道die block steel 模具钢die material 模具材料cold work tool (die) steel 冷作工具（模具）钢hot work tool (die) steel 热作工具（模具）钢holder of punch 凸模夹持器die slide 下模滑动装置turret press 冲模回转压力机blanking die 冲裁模piercing die 冲孔模die,stamping and punching die 冲模die life 冲模寿命die shut height 模具闭合高度clearance between punch and die 凹凸模间隙peak die load 模具最大负荷matrix plate凹模固定板clearance between punch and die 凹凸模间隙matrix plate 凹模固定板cavity plate (block) 凹模die block凸模固定板button die 镶入式圆形凸模gib 凹形拉紧销spanishing凹痕印刷concave angle 凹角concave cutter 凹面铣刀depression 外缩凹孔sinking 凹陷single redessed单面缩凹形clamp-off 铸件凹痕riding 凹陷holder of punch 凸模夹持器clearance between punch and die凹凸模间隙counter punch反凸模angular cams 角凸轮flanged pin 带凸缘销weld flush焊缝凸起flange joint凸缘接头flange connection 凸缘联接convex cutter 凸形铣刀belling 压凸加工cam die bending 凸轮弯曲加工flabging 凸缘加工lug 凸缘crowing 中凸研磨flage wrinkel 凸缘起皱bent pilot 弯曲导正销baffle 导流块ejector guide pin 推板导柱ejector guide bush 板导推套dowel hole 导套孔ejector guide pin 顶出导梢ejector leader busher顶出导梢衬套guide bushing 引导衬套guide pin导梢guide plate 导板guide post 引导柱guide rail 导轨locating pilot pin 定位导梢pass guide穴型导板pilot pin 导销die slide下模滑动装置outer slide外滑块ball silder 球塞滑块slide(slide core) 滑块slip joint 滑配接头snap fit 滑入配合Screw thread lubricant 螺纹润滑剂drawing with ironing 抽引光滑加工dulling平滑glazing光滑剂shot chamber 注射室shot volume 注射量，压注量shot capacity 注射能力injection pressure压射比压，注射压力injection speed 注射速度injection forming 注射成形injection speed 注射速度injection mold 注射模injection mold for thermosets 热固性塑料注射模injection mold for thermoplastics 热塑性塑料注射模shot volume 注射量，压注量shot注射（射次）return-blank type blanking die顶出式落料模ejector guide pin 顶出导梢ejector pad 顶出垫ejector pin顶出梢ejector plate顶出板ejector rod 顶出杆ejector stopper 顶出止动ejector valve 顶出阀ejection pad 顶出衬垫ejector leader busher 顶出导梢衬套head punch 顶镦冲头lifting pin起模顶销pre extrusion punch顶挤冲头runner ejector set 流道顶出器prehardened steel 顶硬钢core-pulling force 抽芯力ejector guide pin 推板导柱ejector guide bush 板导推套ejector pin (plate) 推杆（板）ejector sleeve 推管ejector pin retaining plate 推杆固定板puncher 推杆taper key 推拔键thrust pin 推力销plain tapered bore 普通推拔孔taper shank推拔柄taper tap推拔螺丝攻sprue puller 拉料杆友情提示：本资料代表个人观点，如有帮助请下载，谢谢您的浏览！。