DRC规则 英文对照
DRC规则检查项目
DRC规则检查项⽬PROTEL DXP2004 DRC 规则英⽂对照⼀、Error Reporting 错误报告A：Violations Associated with Buses 有关总线电⽓错误的各类型（共12项）1．bus indices out of range 总线分⽀索引超出范围.2．Bus range syntax errors 总线范围的语法错误3．Illegal bus range values ⾮法的总线范围值4．Illegal bus definitions 定义的总线⾮法5．Mismatched bus label ordering 总线分⽀⽹络标号错误排序6．Mismatched bus/wire object on wire/bus 总线/导线错误的连接导线/总线7．Mismatched bus widths 总线宽度错误8．Mismatched bus section index ordering 总线范围值表达错误,9．Mismatched electrical types on bus 总线上错误的电⽓类型10．Mismatched generics on bus (first index) 总线范围值的⾸位错误11．Mismatched generics on bus (second index) 总线范围值末位错误12．Mixed generics and numeric bus labeling 总线命名规则错误 ) B：Violations Associated Components 有关元件符号电⽓错误（共20项）1．Component Implementations with duplicate pins usage 元件管脚在原理图中重复被使⽤2．Component Implementations with invalid pin mappings 元件管脚在应⽤中和PCB封装中的焊盘不符3．Component Implementations with missing pins in sequence 元件管脚的序号出现序号丢失4．Component contaning duplicate sub-parts 元件中出现了重复的⼦部分5．Component with duplicate Implementations 元件被重复使⽤6. Component with duplicate pins 元件中有重复的管脚7. Duplicate component models ⼀个元件被定义多种重复模型)8. Duplicate part designators 元件中出现标⽰号重复的部分9. Errors in component model parameters 元件模型中出现错误的的参数10.Extra pin found in component display mode 多余的管脚在元件上显⽰.11.Mismatched hidden pin component 元件隐藏管脚的连接不匹配12.Mismatched pin visibility 管脚的可视性不匹配13.Missing component model parameters 元件模型参数丢失14.Missing component models 元件模型丢失15.Missing component models in model files 元件模型不能在模型⽂件中找到16.Missing pin found in component display mode 不见的管脚在元件上显⽰17.Models found in different model locations 元件模型在未知的路径中找到18.Sheet symbol with duplicate entries ⽅框电路图中出现重复的端⼝19.Un-designated parts requiring annotation 未标记的部分需要⾃动标号20.Unused sub-part in component 元件中某个部分未使⽤C：violations associated with document 相关的⽂档电⽓错误（共10项）1.conflicting constraints 约束不⼀致的2.duplicate sheet symbol name 层次原理图中使⽤了重复的⽅框电路图3.duplicate sheet numbers 重复的原理图图纸序号.4.missing child sheet for sheet symbol ⽅框图没有对应的⼦电路图5.missing configuration target 缺少配置对象6.missing sub-project sheet for component 元件丢失⼦项⽬7.multiple configuration targets ⽆效的配置对象8.multiple top-level document ⽆效的顶层⽂件9.port not linked to parent sheet symbol ⼦原理图中的端⼝没有对应到总原理图上的端⼝10.sheet enter not linked to child sheet ⽅框电路图上的端⼝在对应⼦原理图中没有对应端⼝D：violations associated with nets 有关⽹络电⽓错误（共19项）1.adding hidden net to sheet 原理图中出现隐藏⽹络2.adding items from hidden net to net 在隐藏⽹络中添加对象到已有⽹络中3.auto-assigned ports to device pins ⾃动分配端⼝到设备引脚4.duplicate nets 原理图中出现重名的⽹络5.floating net labels 原理图中有悬空的⽹络标签6.global power-objects scope changes 全局的电源符号错误/doc/661647277.htmlparameters with no name ⽹络属性中缺少名称/doc/661647277.htmlparameters with no value ⽹络属性中缺少赋值/doc/661647277.htmls containing floating input pins ⽹络包括悬空的输⼊引脚/doc/661647277.htmls with multiple names 同⼀个⽹络被附加多个⽹络名/doc/661647277.htmls with no driving source ⽹络中没有驱动/doc/661647277.htmls with only one pin ⽹络只连接⼀个引脚/doc/661647277.htmls with possible connection problems ⽹络可能有连接上的错误14.signals with multiple drivers 重复的驱动信号15.sheets containing duplicate ports 原理图中包含重复的端⼝16.signals with load 信号⽆负载17.signals with drivers 信号⽆驱动18.unconnected objects in net ⽹络中的元件出现未连接对象19.unconnected wires 原理图中有没连接的导线E：Violations associated with others有关原理图的各种类型的错误(3项)1.No Error ⽆错误2.Object not completely within sheet boundaries 原理图中的对象超出了图纸边框3.Off-grid object原理图中的对象不在格点位置F：Violations associated with parameters 有关参数错误的各种类型1.same parameter containing different types 相同的参数出现在不同的模型中2.same parameter containing different values 相同的参数出现了不同的取值⼆、Comparator 规则⽐较A：Differences associated with components 原理图和PCB上有关的不同(共16项)1.Changed channel class name 通道类名称变化2.Changed component class name 元件类名称变化3.Changed net class name ⽹络类名称变化4.Changed room definitions 区域定义的变化5.Changed Rule 设计规则的变化6.Channel classes with extra members 通道类出现了多余的成员/doc/661647277.htmlponent classes with extra members 元件类出现了多余的成员8.Difference component 元件出现不同的描述9.Different designators 元件标⽰的改变10.Different library references 出现不同的元件参考库11.Different types 出现不同的标准12.Different footprints 元件封装的改变13.Extra channel classes 多余的通道类14.Extra component classes 多余的元件类15.Extra component 多余的元件16.Extra room definitions 多余的区域定义B：Differences associated with nets 原理图和PCB上有关⽹络不同（共6项）1.Changed net name ⽹络名称出现改变2.Extra net classes 出现多余的⽹络类3.Extra nets 出现多余的⽹络4.Extra pins in nets ⽹络中出现多余的管脚5.Extra rules ⽹络中出现多余的设计规则/doc/661647277.htmlclass with Extra members ⽹络中出现多余的成员C：Differences associated with parameters 原理图和PCB上有关的参数不同（共3项）1.Changed parameter types 改变参数类型2.Changed parameter value 改变参数的取值3.Object with extra parameter 对象出现多余的参数【Violations Associated with Buses】栏——总线电⽓错误类型（1）【Bus indices out of range】：总线分⽀索引超出范围。
PROTELDXP2004中的DRC规则检查项目
在PROTE L DXP2004中的DRC规则检查项目,对于一些英文水平较薄弱的朋友是一个大难题,特和同事对其进行整理一下,英文水平有限,仅供参考:PR OTELDXP2004 DR C 规则英文对照一、Err or Re porti ng 错误报告A：Viol ation s Ass ociat ed wi th Bu ses 有关总线电气错误的各类型（共12项）b us in dices outof ra nge 总线分支索引超出范围Busrange synt ax er rors总线范围的语法错误Ille gal b us ra nge v alues非法的总线范围值Ille gal b us de finit ions定义的总线非法M ismat chedbus l abelorder ing 总线分支网络标号错误排序Mi smatc hed b us/wi re ob jecton wi re/bu s 总线/导线错误的连接导线/总线M ismat chedbus w idths总线宽度错误M ismat chedbus s ectio n ind ex or derin g 总线范围值表达错误Mi smatc hed e lectr icaltypes on b us 总线上错误的电气类型Misma tched gene ricson bu s (fi rst i ndex)总线范围值的首位错误Mi smatc hed g eneri cs on bus(seco nd in dex)总线范围值末位错误Mixe d gen erics andnumer ic bu s lab eling总线命名规则错误B：Vi olati ons A ssoci atedCompo nents有关元件符号电气错误（共20项）C ompon ent I mplem entat ionswithdupli catepinsusage元件管脚在原理图中重复被使用Com ponen t Imp lemen tatio ns wi th in valid pinmappi ngs 元件管脚在应用中和PC B封装中的焊盘不符Comp onent Impl ement ation s wit h mis singpinsin se quenc e 元件管脚的序号出现序号丢失Com ponen t con tanin g dup licat e sub-part s 元件中出现了重复的子部分Comp onent with dupl icate Impl ement ation s 元件被重复使用Comp onent with dupl icate pins元件中有重复的管脚Dup licat e com ponen t mod els 一个元件被定义多种重复模型D uplic ate p art d esign ators元件中出现标示号重复的部分Erro rs in comp onent mode l par amete rs 元件模型中出现错误的的参数Ex tra p in fo und i n com ponen t dis playmode多余的管脚在元件上显示Mi smatc hed h idden pincompo nent元件隐藏管脚的连接不匹配M ismat chedpin v isibi lity管脚的可视性不匹配Miss ing c ompon ent m odelparam eters元件模型参数丢失Miss ing c ompon ent m odels元件模型丢失M issin g com ponen t mod els i n mod el fi les 元件模型不能在模型文件中找到Missi ng pi n fou nd in comp onent disp lay m ode 不见的管脚在元件上显示Mod els f oundin di ffere nt mo del l ocati ons 元件模型在未知的路径中找到S heetsymbo l wit h dup licat e ent ries方框电路图中出现重复的端口Un-de signa ted p artsrequi ringannot ation未标记的部分需要自动标号Unuse d sub-part in c ompon ent 元件中某个部分未使用C：vi olati ons a ssoci atedwithdocum ent 相关的文档电气错误（共10项）conf licti ng co nstra ints约束不一致的du plica te sh eet s ymbol name层次原理图中使用了重复的方框电路图dupli catesheet numb ers 重复的原理图图纸序号miss ing c hildsheet forsheet symb ol 方框图没有对应的子电路图mis singconfi gurat ion t arget缺少配置对象m issin g sub-proj ect s heetfor c ompon ent 元件丢失子项目mu ltipl e con figur ation targ ets 无效的配置对象mu ltipl e top-leve l doc ument无效的顶层文件portnot l inked to p arent shee t sym bol 子原理图中的端口没有对应到总原理图上的端口she et en ter n ot li nkedto ch ild s heet方框电路图上的端口在对应子原理图中没有对应端口D：vio latio ns as socia ted w ith n ets 有关网络电气错误（共19项）addin g hid den n et to shee t 原理图中出现隐藏网络a dding item s fro m hid den n et to net在隐藏网络中添加对象到已有网络中au to-as signe d por ts to devi ce pi ns 自动分配端口到设备引脚dupl icate nets原理图中出现重名的网络f loati ng ne t lab els 原理图中有悬空的网络标签gl obalpower-obje cts s copechang es 全局的电源符号错误n et pa ramet ers w ith n o nam e 网络属性中缺少名称ne t par amete rs wi th no valu e 网络属性中缺少赋值ne ts co ntain ing f loati ng in put p ins 网络包括悬空的输入引脚net s wit h mul tiple name s 同一个网络被附加多个网络名net s wit h nodrivi ng so urce网络中没有驱动n ets w ith o nly o ne pi n 网络只连接一个引脚ne ts wi th po ssibl e con necti on pr oblem s 网络可能有连接上的错误signa ls wi th mu ltipl e dri vers重复的驱动信号s heets cont ainin g dup licat e por ts 原理图中包含重复的端口sign als w ith l oad 信号无负载sign als w ith d river s 信号无驱动u nconn ected obje cts i n net网络中的元件出现未连接对象unco nnect ed wi res 原理图中有没连接的导线E：V iolat ionsassoc iated with othe rs有关原理图的各种类型的错误(3项)No E rror无错误Objec t not comp letel y wit hin s heetbound aries原理图中的对象超出了图纸边框Off-grid obje ct原理图中的对象不在格点位置F：V iolat ionsassoc iated with para meter s 有关参数错误的各种类型sameparam eterconta ining diff erent type s 相同的参数出现在不同的模型中sa me pa ramet er co ntain ing d iffer ent v alues相同的参数出现了不同的取值二、Co mpara tor 规则比较A：Dif feren ces a ssoci atedwithcompo nents原理图和PCB上有关的不同(共16项) Cha ngedchann el cl ass n ame 通道类名称变化Ch anged comp onent clas s nam e 元件类名称变化Chan ged n et cl ass n ame 网络类名称变化Ch anged room defi nitio ns 区域定义的变化Cha ngedRule设计规则的变化C hanne l cla sseswithextra memb ers 通道类出现了多余的成员Com ponen t cla sseswithextra memb ers 元件类出现了多余的成员Dif feren ce co mpone nt 元件出现不同的描述D iffer ent d esign ators元件标示的改变Diffe rentlibra ry re feren ces 出现不同的元件参考库Diff erent type s 出现不同的标准Diff erent foot print s 元件封装的改变Extr a cha nnelclass es 多余的通道类Extr a com ponen t cla sses多余的元件类Ex tra c ompon ent 多余的元件Extr a roo m def initi ons 多余的区域定义B：Diffe rence s ass ociat ed wi th ne ts 原理图和PCB上有关网络不同（共6项）C hange d net name网络名称出现改变Extr a net clas ses 出现多余的网络类E xtranets出现多余的网络E xtrapinsin ne ts 网络中出现多余的管脚Extra rule s 网络中出现多余的设计规则Netclass with Extr a mem bers网络中出现多余的成员C：D iffer ences asso ciate d wit h par amete rs 原理图和PCB上有关的参数不同（共3项）Chang ed pa ramet er ty pes 改变参数类型Cha ngedparam etervalue改变参数的取值Objec t wit h ext ra pa ramet er 对象出现多余的参数。
protel错误提示
Object not completely within sheet boundaries 原理图中的对象超出了图纸边框
Off-grid object原理图中的对象不在格点位置
F：Violations associated with parameters 有关参数错误的各种类型
Extra nets 出现多余的网络
Extra pins in nets 网络中出现多余的管脚
Extra rules 网络中出现多余的设计规则
Net class with Extra members 网络中出现多余的成员
C：Differences associated with parameters 原理图和PCB上有关的参数不同（共3项）
nets containing floating input pins 网络包括悬空的输入引脚
nets with multiple names 同一个网络被附加多个网络名
nets with no driving source 网络中没有驱动
nets with only one pin 网络只连接一个引脚
missing configuration target 缺少配置对象
missing sub-project sheet for component 元件丢失子项目
multiple configuration targets 无效的配置对象
multiple top-level document 无效的顶层文件
signals with drivers 信号无驱动
unconnected objects in net 网络中的元件出现未连接对象
AD报错语句
multiple configuration targets 无效的配置对象
multiple top-level document 无效的顶层文件
port not linked to parent sheet symbol 子原理图中的端口没有对应到总原理图上的端口 sheet enter not linked to child sheet 方框电路图上的端口在对应子原理图中没有对应端口 D：violations associated with nets 有关网络电气错误（共19项）
No Error 无错误
Object not completely within sheet boundaries 原理图中的对象超出了图纸边框 Off-grid object原理图中的对象不在格点位置
F：Violations associated with parameters 有关参数错误的各种类型
Altium Designer Summer 09 DRC
PROTEL DXP2004 DRC 规则英文对照2008-09-24 10:47在PROTEL DXP2004中的DRC规则检查项目,对于一些英文水平较薄弱的朋友是一个大难题,特和同事对其进行整理一下,英文水平有限,仅供参考:
PROTEL DXP2004 DRC 规则英文对照
Un-designated parts requiring annotation 未标记的部分需要自动标号
Unused sub-part in component 元件中某个部分未使用
C：violations associated with document 相关的文档电气错误（共10项）
New GMP ANVISA Regulation - RDC16 2013 - English Version(1)-对照译文
注：参考葡萄牙语-英语翻译版本美国食品和药物管理局质量体系要求第21章第820节的基本术语。
Note: The translation from Portuguese to English used as referencethe basic terminology of the FDA QSR 21 Part 820.巴西国家卫生监督局——联合董事会决议第16号RDC2013年3月28日ANVISA - COLLEGIATE BOARD RESOLUTION RDC No.16 28 MAR 2013批准医疗用品与体外诊断用品的良好生产技术规范及其他措施。
Approves the Technical Regulation of Good Manufacturing Practice for M edical Products and Products for In Vitro Diagnostic Use and other mea sures.巴西国家卫生监督局在2013年3月7日召开的会议上，根据第1999年4月16日3029号法令批准的规范的第11条第4款规定，以及根据巴西国家卫生监督局的第354号法令附录一批准的附则的第54条第1款与第3款规定获得授权行使权力，公布于20 06年8月21日的公报上。
参考1976年9月23日生效的6360号法案及其规定，以及19 77年1月5日的79094号法令；The Board of the National Health Surveillance Agency, in exercise of t he powers conferred upon him by section IV of article. 11 of the Regul ation approved by Decree No. 3029 of April 16, 1999, and in view of th e provisions of section II and in § 1 and § 3 of art. 54 of the Byla ws approved in accordance with Annex I of Ordinance No. 354 of ANVISA, of August 11, 2006, republished in the Official Gazette of August 21, 2006, at a meeting held March 7, 2013, considering the Law. 6360 of Se ptember 23, 1976 and its regulations, Decree No. 79094 of January 5, 1 977;参考了内在化决议南美共同市场/GMC/RES的需要。
空运术语中英文对照
空运术语
PRF: PROCEDURE FEE 手续费 PUC : PICK UP CHARGE 提货费 QUC: QUARANTINE CHARGE 检疫费 REF :REGISTER FEE 注册费 SCA :SERVICE CHARGE DUE AGENT 代理服务费
空运术语
ECC :EXPORT CUSTOMS CHARGE 出口报关费 ERD :ERD 汇率差 FAC :FAX CHARGE 电传费 FKC :FORKLIFT CHARGE 叉车费 FRC :FROZEN CHARGE 冷冻费 FUC :FUMIGATING CHARGE 熏蒸费 HAC :HAWB CHARGE 分单费
空运术语
普通货物运价 General Cargo Rates (GCR) 集装设备 Unit Load Devices (ULD) 比例运价 Construction Rate 分段相加运价 Combination of Rate 声明价值费 Valuation Charges 运输声明价值 Declared value for Carriage 不要求声明价值 No Value Declared (NVD)
托运人 (Shipper)：货物运输合同中指定的向收货人发货的人或公司。
活动物／危险品 托运人证明书 (Shipper's Certificate for live animals/ dangerous goods)：托运人所作的声明-声明其货物已根据IATA最新版本的规则和所有承运 人规则和政府法例的规定，将货物妥善包装、准确描述，使其适合于空运。
空术语
HCC :HANDLING CHARGE 操作费(HDC) HQF :HEALTH & QUARANTINE CHARGE 卫检费 ICC :IMPORT CUSTOMS CHARGE 进口报关费 IDF :INSPECTION DECLARE FEE 报验费 INC :INSURANCE CHARGE 保险费 ISC :INLAND SERVICE CHARGE 国内服务费 ITC :INLAND TRANSPORTATION CHARGE 国内运输费
国际救生设备规则(2016英文版-实时综合文本)
Page 1 of 59CHAPTER I GENERAL1.1Definitions1.1.1 Convention means the International Convention for the Safety of Life at Sea, 19 74, asamended.1.1.2 Effective clearing of the ship is the ability of the free-fall lifeboat to move away fromthe ship after free-fall launching without using its engine.1.1.3 Free-fall acceleration is the rate of change of velocity experienced by the occup antsduring launching of a free-fall lifeboat.1.1.4 Free-fall certification height is the greatest launching height for which the lifeb oat is tobe approved, measured from the still water surface to the lowest point on the lifebo at whenthe lifeboat is in the launch configuration.1.1.5 Launching ramp angle is the angle between the horizontal and the launch rail of thelifeboat in its launching position with the ship on even keel.1.1.6 Launching ramp length is the distance between the stern of the lifeboat and the lowerend of the launching ramp.1.1.7 Regulation means a regulation contained in the Annex to the Convention.1.1.8 Retro-reflective material is a material which reflects in the opposite direction a beamof light directed on it.1.1.9 Water-entry angle is the angle between the horizontal and the launch rail of th elifeboat when it first enters the water. 1.1.10 The terms used in this Code have the sa memeaning as those defined in regulation Ⅲ/3.1.2General requirements for life-saving appliances1.2.1 Paragraph 1.2.2.7 applies to life-saving appliances on all ships.1.2.2 Unless expressly provided otherwise or unless, in the opinion of the Administra tionhaving regard to the particular voyages on which the ship is constantly engaged, ot herrequirements are appropriate, all life-saving appliances prescribed in this part shall: .1 be constructed with proper workmanship and materials;Page 2 of 59 .2 not be damaged in stowage throughout the air temperature range -30℃ to +65℃ and, inthe case of personal life-saving appliances, unless otherwise specified, remain operat ionalthroughout the air temperature range -15℃to +40℃ ;.3 if they are likely to be immersed in seawater during their use, operate throughout theseawater temperature range -1℃to +30℃ ;.4 where applicable, be rot-proof, corrosion-resistant, and not be unduly affected by seawater, oil or fungal attack;.5 where exposed to sunlight, be resistant to deterioration;.6 be of international or vivid reddish orange, or a comparably highly visible colour o n allparts where this will assist detection at sea;.7 be fitted with retro-reflective material where it will assist in detection and in accor dancewith the recommendations of the Organization*;* Refer to the Recommendation on the Use and Fitting of Retro-Reflective Material on Life-savin gAppliances, adopted by the Organization by resolution A.658(16), as it may be amended..8 if they are to be used in a seaway, be capable of satisfactory operation in that environment;.9 be clearly marked with approval information including the Administration which approved it, and any operational restrictions; and.10 where applicable, be provided with electrical short circuit protection to prevent d amageor injury.1.2.3 The Administration shall determine the period of acceptability of life-saving appliances which are subject to deterioration with age. Such life-saving appliances s hall bemarked with a means for determining their age or the date by which they must be r eplaced.Permanent marking with a date of expiry is the preferred method of establishing the periodof acceptability. Batteries not marked with an expiration date may be used if they ar ereplaced annually, or in the case of a secondary battery (accumulator), if the conditi on of theelectrolyte can be readily checked.CHAPTERII PERSONAL LIFE-SAVINGAPPLIANCES2.1Lifebuoys2.1.1 Lifebuoy specificationPage 3 of 59Every lifebuoy shall:.1 have an outer diameter of not more than 800 mm and an inner diameter of not less than400 mm;.2be constructed of inherently buoyant material;it shall not depend upon rus hes,corkshavings or granulated cork,any other loose granulated material or any air co mpartmentwhich depends on inflation for buoyancy;.3 be capable of supporting not less than 14.5 kg of iron in fresh water for a period of 24 h;.4 have a mass of not less than 2.5 kg;.5 not sustain burning or continue melting after being totally enveloped in a fire for a periodof 2 s;.6 be constructed to withstand a drop into the water from the height at which it is stowedabove the waterline in the lightest seagoing condition or30m,whichever is th e greater,without impairing either its operating capability or that of its attached components; .7 if it is intended to operate the quick release arrangement provided for the self-activatedsmoke signals and self-igniting lights, have a mass of not less than 4 kg; and.8 be fitted with a grabline not less than 9.5 mm in diameter and not less than 4 t imes theoutside diameter of the body of the buoy in length.The grabline shall be secur ed at fourequidistant points around the circumference of the buoy to form four equal loops.2.1.2 Lifebuoy self-igniting lightsSelf-igniting lights required by regulation III/7.1.3 shall:.1 be such that they cannot be extinguished by water;.2 be of white colour and capable of either burning continuously with a luminous i ntensityof not less than2cd in all directions of the upper hemisphere or flashing( dischargeflashing) at a rate of not less than 50 flashes and not more than 70 flashes per mi n with atleast the corresponding effective luminous intensity;.3be provided with a source of energy capable of meeting the requirement of paragraph2.1.2.2 for a period of at least 2 h; and.4 be capable of withstanding the drop test required by paragraph 2.1.1.6.2.1.3 Lifebuoy self-activating smoke signalsSelf-activating smoke signals required by regulation III/7.1.3 shall:.1emit smoke of a highly visible colour at a uniform rate for a period of at leas t15minwhen floating in calm water;Page 4 of 59.2not ignite explosively or emit any flame during the entire smoke emission ti me of thesignal;.3 not be swamped in a seaway;.4 continue to emit smoke when fully submerged in water for a period of at least 10 s;.5 be capable of withstanding the drop test required by paragraph 2.1.1.6; and.6 be provided with a quick-release arrangement that will automatically release and activatethe signal and associated self-igniting light connected to a lifebuoy having a ma ss of notmore than 4 kg.2.1.4 Buoyant lifelinesBuoyant lifelines required by regulation III/7.1.2 shall:.1 be non-kinking;.2 have a diameter of not less than 8 mm; and.3 have a breaking strength of not less than 5 kN.2.2Lifejackets2.2.1 General requirements for lifejackets2.2.1.1 A lifejacket shall not sustain burning or continue melting after being totally enveloped in a fire for a period of 2 s.2.2.1.2 Lifejackets shall be provided in three sizes in accordance with table 2.1. If a lifejacket fully complies with the requirements of two adjacent size ranges, it may be marked with both size ranges, but the specified ranges shall not be divided. Lifejacke ts shallbe marked by either weight or height, or by both weight and height, according to ta ble 2.1.Table 2.1 - Lifejacket sizing criteriaLifejacket marking Infant Child AdultUser’s size:15 or more but less thanless than 154343 or more Weight (kg)less than 100100 or more but less155 or more Height (cm)than 155Page 5 of 592.2.1.3 If an adult lifejacket is not designed to fit persons weighing up to 140 kg and with achest girth of up to 1,750 mm, suitable accessories shall be available to allow it to be secured to such persons.2.2.1.4 The in-water performance of a lifejacket shall be evaluated by comparison to theperformance of a suitable size standard reference lifejacket, i.e. reference test device (RTD)complying with the recommendations of the Organization.** Refer to the Revised Recommendation on testing of life-saving appliances (resoluti onMSC.81(70)), as amended.2.2.1.5 An adult lifejacket shall be so constructed that:.1 at least 75% of persons who are completely unfamiliar with the lifejacket can corre ctlydon it within a period of 1 min without assistance, guidance or prior demonstration; .2 after demonstration, all persons can correctly don it within a period of 1 min with outassistance;.3 it is clearly capable of being worn in only one way or inside-out and, if donned incorrectly, it is not injurious to the wearer;.4 the method of securing the lifejacket to the wearer has quick and positive means ofclosure that do not require tying of knots;.5 it is comfortable to wear; and.6 it allows the wearer to jump into the water from a height of at least 4.5 m while h oldingon to the lifejacket, and from a height of at least 1m with arms held overhead, witho ut injuryand without dislodging or damaging the lifejacket or its attachments.2.2.1.6 When tested according to the recommendations of the Organization on at le ast 12persons, adult lifejackets shall have sufficient buoyancy and stability in calm fresh wa ter to:.1 lift the mouth of exhausted or unconscious persons by an average height of not le ss thanthe average provided by the adult RTD;.2 turn the body of unconscious, face-down persons in the water to a position where themouth is clear of the water in an average time not exceeding that of the RTD, with th enumber of persons not turned by the lifejacket no greater than that of the RTD;.3 incline the body backwards from the vertical position for an average torso angle o f notless than that of the RTD minus 5°;.4 lift the head above horizontal for an average faceplane angle of not less than that of theRTD minus 5°; andPage 6 of 59.5 return the wearer to a stable face-up position after being destabilized when floati ng in theflexed foetal position.**** Refer to the illustration on page 11 of the IMO Pocket Guide to Cold Water Surviv al andto the Revised Recommendation on testing of life-saving appliances (resolution MSC .81(70)), as amended.2.2.1.7 An adult lifejacket shall allow the person wearing it to swim a short distance a nd toboard a survival craft.2.2.1.8 An infant or child lifejacket shall perform the same as an adult lifejacket exce pt asfollows:.1 donning assistance is permitted for small children and infants;.2 the appropriate child or infant RTD shall be used in place of the adult RTD; and.3 assistance may be given to board a survival craft, but wearer mobility shall not be reduced to any greater extent than by the appropriate size RTD.2.2.1.9 With the exception of freeboard and self-righting performance, the requirem ents forinfant lifejackets may be relaxed, if necessary, in order to:.1 facilitate the rescue of the infant by a caretaker;.2 allow the infant to be fastened to a caretaker and contribute to keeping the infant close tothe caretaker;.3 keep the infant dry, with free respiratory passages;.4 protect the infant against bumps and jolts during evacuation; and.5 allow a caretaker to monitor and control heat loss by the infant.2.2.1.10 In addition to the markings required by paragraph 1.2.2.9, an infant or child lifejacket shall be marked with:.1 the size range in accordance with paragraph 2.2.1.2; and.2 an “infant” or “child” symbol as shown in the “infant’s lifejacket” or “child’s lifejacket”symbol adopted by the Organization.****** Refer to Symbols related to life-saving appliances and arrangements, adopted bytheOrganization by resolution A.760(18), as amended.2.2.1.11 A lifejacket shall have buoyancy which is not reduced by more than 5% after 24 hsubmersion in fresh water.Page 7 of 592.2.1.12 The buoyancy of a lifejacket shall not depend on the use of loose granulate dmaterials.2.2.1.13 Each lifejacket shall be provided with means of securing a lifejacket light as specified in paragraph 2.2.3 such that it shall be capable of complying with paragrap hs2.2.1.5.6 and 2.2.3.1.3.2.2.1.14 Each lifejacket shall be fitted with a whistle firmly secured by a lanyard.2.2.1.15 Lifejacket lights and whistles shall be selected and secured to the lifejacket i n sucha way that their performance in combination is not degraded.2.2.1.16 A lifejacket shall be provided with a releasable buoyant line or other means tosecure it to a lifejacket worn by another person in the water.2.2.1.17 A lifejacket shall be provided with a suitable means to allow a rescuer to lift thewearer from the water into a survival craft or rescue boat.2.2.2 Inflatable lifejacketsA lifejacket which depends on inflation for buoyancy shall have not less than two se paratecompartments, shall comply with the requirements of paragraph 2.2.1 and shall:.1 inflate automatically upon immersion, be provided with a device to permit inflatio n by asingle manual motion and be capable of having each chamber inflated by mouth;.2 in the event of loss of buoyancy in any one compartment be capable of complyin g withthe requirements of paragraphs 2.2.1.5, 2.2.1.6 and 2.2.1.7; and.3 comply with the requirements of paragraph 2.2.1.11 after inflation by means of th eautomatic mechanism.2.2.3 Lifejacket lights2.2.3.1 Each lifejacket light shall:.1 have a luminous intensity of not less than 0.75 cd in all directions of the upper hemisphere;.2 have a source of energy capable of providing a luminous intensity of 0.75 cd for a periodof at least 8 h;.3 be visible over as great a segment of the upper hemisphere as is practicable when attached to a lifejacket; and.4 be of white colour.2.2.3.2 If the light referred to in paragraph 2.2.3.1 is a flashing light, it shall, in additi on:Page 8 of 59.1 be provided with a manually operated switch; and.2 flash at a rate of not less than 50 flashes and not more than 70 flashes per minute with aneffective luminous intensity of at least 0.75 cd.”2.3Immersion suits2.3.1 General requirements for immersion suits2.3.1.1 An immersion suit shall be constructed with waterproof materials such that: .1 it can be unpacked and donned without assistance within 2 min, taking into accou ntdonning of any associated clothing, donning of a lifejacket if the immersion suit is t o beworn in conjunction with a lifejacket, and inflation of orally inflatable chambers, if fitt ed;** Refer to paragraph 3.1.3 of the Recommendation on testing of life-saving applianc es,adopted by the Organization by resolution MSC.81(70)..2 it will not sustain burning or continue melting after being totally enveloped in a fi re for aperiod of 2 s;.3 it will cover the whole body with the exception of the face, except that covering fo r thehands may be provided by separate gloves which shall be permanently attached to t he suit;.4 it is provided with arrangements to minimize or reduce free air in the legs of the s uit; and.5 following a jump from a height of not less than 4.5 m into the water there is no u ndueingress of water into the suit.2.3.1.2 An immersion suit on its own, or worn in conjunction with a lifejacket if neces sary,shall have sufficient buoyancy and stability in calm fresh water to:.1 lift the mouth of an exhausted or unconscious person clear of the water by not les s than120 mm; and.2 allow the wearer to turn from a face-down to a face-up position in not more than5 s.2.3.1.3 An immersion suit shall permit the person wearing it, and also wearing a lifej acket ifthe immersion suit is to be worn in conjunction with a lifejacket, to:.1 climb up and down a vertical ladder at least 5 m in length;.2 perform normal duties associated with abandonment;.3 jump from a height of not less than 4.5 m into the water without damaging or disl odgingthe immersion suit or its attachments, or being injured; and.4 swim a short distance through the water and board a survival craft.Page 9 of 59 2.3.1.4 An immersion suit which has buoyancy and is designed to be worn without a lifejacket shall be fitted with a light complying with the requirements of paragraph 2.2.3 andthe whistle prescribed by paragraph 2.2.1.14.2.3.1.5 An immersion suit which has buoyancy and is designed to be worn without a lifejacket shall be provided with a releasable buoyant line or other means to secure i t to asuit worn by another person in the water.2.3.1.6 An immersion suit which has buoyancy and is designed to be worn without a lifejacket shall be provided with a suitable means to allow a rescuer to lift the wearer fromthe water into a survival craft or rescue boat.2.3.1.7 If an immersion suit is to be worn in conjunction with a lifejacket, the lifejacke t shallbe worn over the immersion suit. Persons wearing such an immersion suit shall be a ble todon a lifejacket without assistance. The immersion suit shall be marked to indicate t hat itmust be worn in conjunction with a compatible lifejacket.2.3.1.8 An immersion suit shall have buoyancy which is not reduced by more than 5 % after24 h submersion in fresh water and does not depend on the use of loose granulated materials.2.3.2 Thermal performance requirements for immersion suits2.3.2.1 An immersion suit made of material which has no inherent insulation shall be: .1 marked with instructions that it must be worn in conjunction with warm clothing; and.2 so constructed that, when worn in conjunction with warm clothing, and with a lifej acket ifthe immersion suit is to be worn with a lifejacket, the immersion suit continues to pr ovidesufficient thermal protection, following one jump by the wearer into the water from a heightof 4.5 m, to ensure that when it is worn for a period of 1 h in calm circulating water at atemperature of 5℃, the wearer's body core temperature does not fall more than 2℃.2.3.2.2 An immersion suit made of material with inherent insulation, when worn eith er onits own or with a lifejacket, if the immersion suit is to be worn in conjunction with a lifejacket, shall provide the wearer with sufficient thermal insulation, following one ju mpinto the water from a height of 4.5 m, to ensure that the wearer's body core tempera ture doesnot fall more than 2℃ after a period of 6 h immersion in calm circulating water at a temperature of between 0℃ and 2℃.2.4Anti-exposure suits2.4.1 General requirements for anti-exposure suitsPage 10 of 592.4.1.1 An anti-exposure suit shall be constructed with waterproof materials such tha t it:.1 provides inherent buoyancy of at least 70 N;.2is made of material which reduces the risk of heat stress during rescue and e vacuationoperations;.3 covers the whole body except, where the Administration so permits, the feet; cov ering forthe hands and head may be provided by separate gloves and a hood, both of whic h shall bepermanently attached to the suit;.4 can be unpacked and donned without assistance within 2 min;.5 does not sustain burning or continue melting after being totally enveloped in a fire for aperiod of 2 s;.6 is equipped with a pocket for a portable VHF telephone; and.7 has a lateral field of vision of at least 120°.2.4.1.2 An anti-exposure suit shall permit the person wearing it to:.1 climb up and down a vertical ladder of at least 5 m in length;.2 jump from a height of not less than 4.5 m into the water with feet first, without d amagingor dislodging the suit, or its attachments, or being injured;.3 swim through the water at least 25 m and board a survival craft;.4 don a lifejacket without assistance; and.5 perform all duties associated with abandonment, assist others and operate a rescue boat.2.4.1.3 An anti-exposure suit shall be fitted with a light complying with the require ments ofparagraph2.2.3such that it shall be capable of complying with paragraphs2.2.3.1.3and2.4.1.2.2, and the whistle prescribed by paragraph 2.2.1.14.2.4.2 Thermal performance requirements for anti-exposure suits2.4.2.1 An anti-exposure suit shall:.1 if made of material which has no inherent insulation, be marked with instruction s that itmust be worn in conjunction with warm clothing; and.2be so constructed that,when worn as marked and following one jump into the waterwhich totally submerges the wearer,the suit continues to provide sufficient thermalprotection to ensure that when it is worn in calm circulating water at a temperatur e of 5℃,the wearer’s body core temperature does not fall at a rate of more than 1.5℃ per hour, after the first 0.5 h.Page 11 of 59 2.4.3 Stability requirements A person in fresh water wearing an anti-exposure suit complying with the requirements of this section shall be able to turn from a face-do wn to aface-up position in not more than 5 s and shall be stable face-up. The suit shall have notendency to turn the wearer face-down in moderate sea condition.2.5Thermal protective aids2.5.1 A thermal protective aid shall be made of waterproof material having a thermal conductance of not more than 7,800 W/(m2K) and shall be so constructed that, whe n used toenclose a person, it shall reduce both the convective and evaporative heat loss from thewearer's body.2.5.2 The thermal protective aid shall:.1 cover the whole body of persons of all sizes wearing a lifejacket with the exceptio n of theface. Hands shall also be covered unless permanently attached gloves are provided; .2 be capable of being unpacked and easily donned without assistance in a survival craft orrescue boat; and.3 permit the wearer to remove it in the water in not more than 2 min, if it impairs a bility toswim.2.5.3 The thermal protective aid shall function properly throughout an air temperatu re range-30℃ to+20℃.CHAPTERIII VISUAL SIGNALS3.1Rocket parachute flares3.1.1 The rocket parachute flare shall:.1 be contained in a water-resistant casing;.2have brief instructions or diagrams clearly illustrating the use of the rocket p arachuteflare printed on its casing;.3 have integral means of ignition; and.4 be so designed as not to cause discomfort to the person holding the casing wh en used inaccordance with the manufacturer's operating instructions.Page 12 of 593.1.2 The rocket shall, when fired vertically, reach an altitude of not less than 300 m. At ornear the top of its trajectory, the rocket shall eject a parachute flare, which shall:.1 burn with a bright red colour;.2 burn uniformly with an average luminous intensity of not less than 30,000 cd;.3 have a burning period of not less than 40 s;.4 have a rate of descent of not more than 5 m/s; and.5 not damage its parachute or attachments while burning.3.2Hand flares3.2.1 The hand flare shall:.1 be contained in a water-resistant casing;.2 have brief instructions or diagrams clearly illustrating the use of the hand flare pri nted onits casing;.3 have a self-contained means of ignition; and.4be so designed as not to cause discomfort to the person holding the casi ng and notendanger the survival craft by burning or glowing residues when used in accorda nce withthe manufacturer's operating instructions.3.2.2 The hand flare shall:.1 burn with a bright red colour;.2 burn uniformly with an average luminous intensity of not less than 15,000 cd ;.3 have a burning period of not less than 1 min; and.4 continue to burn after having been immersed for a period of 10 s under 100 mm of water.3.3Buoyant smoke signals3.3.1 The buoyant smoke signal shall:.1 be contained in a water-resistant casing;Page 13 of 59.2not ignite explosively when used in accordance with the manufacturer's operatinginstructions; and.3have brief instructions or diagrams clearly illustrating the use of the buoya nt smokesignal printed on its casing.3.3.2 The buoyant smoke signal shall:.1 emit smoke of a highly visible colour at a uniform rate for a period of not less tha n 3 minwhen floating in calm water;.2 not emit any flame during the entire smoke emission time;.3 not be swamped in a seaway; and.4 continue to emit smoke when submerged in water for a period of 10 s under 10 0 mm ofwater.CHAPTER IV-SURVIVAL CRAFT4.1General requirements for liferafts4.1.1 Construction of liferafts4.1.1.1 Every liferaft shall be so constructed as to be capable of withstanding exposu re for30 days afloat in all sea conditions.4.1.1.2 The liferaft shall be so constructed that when it is dropped into the water fro m aheight of 18 m, the liferaft and its equipment will operate satisfactorily. If the liferaft is tobe stowed at a height of more than 18 m above the waterline in the lightest seagoin gcondition, it shall be of a type which has been satisfactorily drop-tested from at least thatheight.4.1.1.3 The floating liferaft shall be capable of withstanding repeated jumps on to it f rom aheight of at least 4.5 m above its floor both with and without the canopy erected. 4.1.1.4 The liferaft and its fittings shall be so constructed as to enable it to be towed at aspeed of 3 knots in calm water when loaded with its full complement of persons and equipment and with one of its sea-anchors streamed.4.1.1.5 The liferaft shall have a canopy to protect the occupants from exposure which isautomatically set in place when the liferaft is launched and waterborne. The canopy shallcomply with the following:Page 14 of 59.1 it shall provide insulation against heat and cold by means of either two layers of materialseparated by an air gap or other equally efficient means. Means shall be provided to preventaccumulation of water in the air gap;.2 its interior shall be of a colour that does not cause discomfort to the occupants; .3 each entrance shall be clearly indicated and be provided with efficient adjustable c losingarrangements which can be easily and quickly opened by persons clothed in immers ion suitsfrom inside and outside, and closed from inside, the liferaft so as to permit ventilatio n butexclude seawater, wind and cold. Liferafts accommodating more than eight persons shallhave at least two diametrically opposite entrances;.4 it shall admit sufficient air for the occupants at all times, even with the entrances c losed;.5 it shall be provided with at least one viewing port;.6 it shall be provided with means for collecting rain water;.7 it shall be provided with means to mount a survival craft radar transponder at a h eight ofat least 1 m above the sea; and.8 it shall have sufficient headroom for sitting occupants under all parts of the canop y.4.1.2 Minimum carrying capacity and mass of liferafts4.1.2.1 No liferaft shall be approved which has a carrying capacity of less than six per sonscalculated in accordance with the requirements of paragraph 4.2.3 or 4.3.3, as appro priate.4.1.2.2 Unless the liferaft is to be launched by an approved launching appliance com plyingwith the requirements of section 6.1 or is not intended for easy side-to-side transfer, the totalmass of the liferaft, its container and its equipment shall not be more than 185 kg.4.1.3 Liferaft fittings4.1.3.1 Lifelines shall be securely becketed around the inside and outside of the lifera ft.。
DRC规则检查项目
PROTEL DXP2004 DRC 规则英文对照一、Error Reporting 错误报告A：Violations Associated with Buses 有关总线电气错误的各类型（共12项）1．bus indices out of range 总线分支索引超出范围.2．Bus range syntax errors 总线范围的语法错误3．Illegal bus range values 非法的总线范围值4．Illegal bus definitions 定义的总线非法5．Mismatched bus label ordering 总线分支网络标号错误排序6．Mismatched bus/wire object on wire/bus 总线/导线错误的连接导线/总线7．Mismatched bus widths 总线宽度错误8．Mismatched bus section index ordering 总线范围值表达错误,9．Mismatched electrical types on bus 总线上错误的电气类型10．Mismatched generics on bus (first index) 总线范围值的首位错误11．Mismatched generics on bus (second index) 总线范围值末位错误12．Mixed generics and numeric bus labeling 总线命名规则错误 ) B：Violations Associated Components 有关元件符号电气错误（共20项）1．Component Implementations with duplicate pins usage 元件管脚在原理图中重复被使用2．Component Implementations with invalid pin mappings 元件管脚在应用中和PCB封装中的焊盘不符3．Component Implementations with missing pins in sequence 元件管脚的序号出现序号丢失4．Component contaning duplicate sub-parts 元件中出现了重复的子部分5．Component with duplicate Implementations 元件被重复使用6. Component with duplicate pins 元件中有重复的管脚7. Duplicate component models 一个元件被定义多种重复模型)8. Duplicate part designators 元件中出现标示号重复的部分9. Errors in component model parameters 元件模型中出现错误的的参数10.Extra pin found in component display mode 多余的管脚在元件上显示.11.Mismatched hidden pin component 元件隐藏管脚的连接不匹配12.Mismatched pin visibility 管脚的可视性不匹配13.Missing component model parameters 元件模型参数丢失14.Missing component models 元件模型丢失15.Missing component models in model files 元件模型不能在模型文件中找到16.Missing pin found in component display mode 不见的管脚在元件上显示17.Models found in different model locations 元件模型在未知的路径中找到18.Sheet symbol with duplicate entries 方框电路图中出现重复的端口19.Un-designated parts requiring annotation 未标记的部分需要自动标号20.Unused sub-part in component 元件中某个部分未使用C：violations associated with document 相关的文档电气错误（共10项）1.conflicting constraints 约束不一致的2.duplicate sheet symbol name 层次原理图中使用了重复的方框电路图3.duplicate sheet numbers 重复的原理图图纸序号.4.missing child sheet for sheet symbol 方框图没有对应的子电路图5.missing configuration target 缺少配置对象6.missing sub-project sheet for component 元件丢失子项目7.multiple configuration targets 无效的配置对象8.multiple top-level document 无效的顶层文件9.port not linked to parent sheet symbol 子原理图中的端口没有对应到总原理图上的端口10.sheet enter not linked to child sheet 方框电路图上的端口在对应子原理图中没有对应端口D：violations associated with nets 有关网络电气错误（共19项）1.adding hidden net to sheet 原理图中出现隐藏网络2.adding items from hidden net to net 在隐藏网络中添加对象到已有网络中3.auto-assigned ports to device pins 自动分配端口到设备引脚4.duplicate nets 原理图中出现重名的网络5.floating net labels 原理图中有悬空的网络标签6.global power-objects scope changes 全局的电源符号错误 parameters with no name 网络属性中缺少名称 parameters with no value 网络属性中缺少赋值s containing floating input pins 网络包括悬空的输入引脚s with multiple names 同一个网络被附加多个网络名s with no driving source 网络中没有驱动s with only one pin 网络只连接一个引脚s with possible connection problems 网络可能有连接上的错误14.signals with multiple drivers 重复的驱动信号15.sheets containing duplicate ports 原理图中包含重复的端口16.signals with load 信号无负载17.signals with drivers 信号无驱动18.unconnected objects in net 网络中的元件出现未连接对象19.unconnected wires 原理图中有没连接的导线E：Violations associated with others有关原理图的各种类型的错误(3项)1.No Error 无错误2.Object not completely within sheet boundaries 原理图中的对象超出了图纸边框3.Off-grid object原理图中的对象不在格点位置F：Violations associated with parameters 有关参数错误的各种类型1.same parameter containing different types 相同的参数出现在不同的模型中2.same parameter containing different values 相同的参数出现了不同的取值二、Comparator 规则比较A：Differences associated with components 原理图和PCB上有关的不同(共16项)1.Changed channel class name 通道类名称变化2.Changed component class name 元件类名称变化3.Changed net class name 网络类名称变化4.Changed room definitions 区域定义的变化5.Changed Rule 设计规则的变化6.Channel classes with extra members 通道类出现了多余的成员ponent classes with extra members 元件类出现了多余的成员8.Difference component 元件出现不同的描述9.Different designators 元件标示的改变10.Different library references 出现不同的元件参考库11.Different types 出现不同的标准12.Different footprints 元件封装的改变13.Extra channel classes 多余的通道类14.Extra component classes 多余的元件类15.Extra component 多余的元件16.Extra room definitions 多余的区域定义B：Differences associated with nets 原理图和PCB上有关网络不同（共6项）1.Changed net name 网络名称出现改变2.Extra net classes 出现多余的网络类3.Extra nets 出现多余的网络4.Extra pins in nets 网络中出现多余的管脚5.Extra rules 网络中出现多余的设计规则 class with Extra members 网络中出现多余的成员C：Differences associated with parameters 原理图和PCB上有关的参数不同（共3项）1.Changed parameter types 改变参数类型2.Changed parameter value 改变参数的取值3.Object with extra parameter 对象出现多余的参数【Violations Associated with Buses】栏——总线电气错误类型（1）【Bus indices out of range】：总线分支索引超出范围。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Altium designer DRC规则英文对照Altium designer DRC规则英文对照
2009/08/10 14:55
DRC 规则英文对照
Ⅰ：Error Reporting 错误报告
◆bus indices out of range 总线分支索引超出范围
◆Bus range syntax errors 总线范围的语法错误
◆Illegal bus range values 非法的总线范围值
◆Illegal bus definitions 定义的总线非法
◆Mismatched bus label ordering 总线分支网络标号错误排序
◆Mismatched bus/wire object on wire/bus 总线/导线错误的连接导线/总线
◆Mismatched bus widths 总线宽度错误 index ordering 总线范围值表达错误
◆Mismatched electrical types on bus 总线上错误的电气类型
◆Mismatched generics on bus (first index) 总线范围值的首位错误
◆Mismatched generics on bus (second index) 总线范围值末位错误
◆Mixed generics and numeric bus labeling 总线命名规则错误
1、adding hidden net to sheet 原理图中出现隐藏网络
2、adding items from hidden net to net 在隐藏网络中添加对象到已有网络中
3、auto-assigned ports to device pins 自动分配端口到设备引脚
4、duplicate nets 原理图中出现重名的网络
5、floating net labels 原理图中有悬空的网络标签
6、global power-objects scope changes 全局的电源符号错误
7、net parameters with no name 网络属性中缺少名称
8、net parameters with no value 网络属性中缺少赋值
9、nets containing floating input pins 网络包括悬空的输入引脚
10、nets with multiple names 同一个网络被附加多个网络名
11、nets with no driving source 网络中无驱动源
12、nets with only one pin 网络只连接一个引脚
13、nets with possible connection problems 网络可能有连接上的错误
14、signals with multiple drivers 重复的驱动信号
15、sheets containing duplicate ports 原理图中包含重复的端口
16、signals with load 信号无负载
17、signals with drivers 信号无驱动
18、unconnected objects in net 网络中的元件出现未连接对象
19、unconnected wires 原理图中有没连接的导线
E：Violations associated with others有关原理图的各种类型的错误(3项)
1、No Error 无错误
2、Object not completely within sheet boundaries 原理图中的对象超出了图纸边框
3、Off-grid object原理图中的对象不在格点位置
1、same parameter containing different types 相同的参数出现在不同的模型中 same parameter containing different values 相同的参数出现了不同的取值
Ⅱ、Comparator 规则比较◆Changed
◆Changed
◆Changed
◆Changed channel class name 通道类名称变化 component class name 元件类名称变化 net class name 网络类名称变化 room definitions 区域定义的变化
◆Changed Rule 设计规则的变化
◆Channel classes with extra members 通道类出现了多余的成员
◆Component classes with extra members 元件类出现了多余的成员
◆Difference component 元件出现不同的描述
◆Different designators 元件标示的改变
◆Different library references 出现不同的元件参考库
◆Different types 出现不同的标准
◆Different footprints 元件封装的改变
◆Extra channel classes 多余的通道类
◆Extra component classes 多余的元件类
◆Extra component 多余的元件
◆ Extra room definitions 多余的区域定义
Ⅱ、Comparator 规则比较
◆Changed channel class name 通道类名称变化
◆Changed
◆Changed
◆Changed
◆C hanged component class name 元件类名称变化 net class name 网络类名称变化 room definitions 区域定义的变化 Rule 设计规则的变化
◆Channel classes with extra members 通道类出现了多余的成员
◆Component classes with extra members 元件类出现了多余的成员
◆Difference component 元件出现不同的描述
◆Different designators 元件标示的改变
◆Different library references 出现不同的元件参考库
◆Different types 出现不同的标准
◆Different footprints 元件封装的改变
◆Extra channel classes 多余的通道类
◆Extra component classes 多余的元件类
◆Extra component 多余的元件
◆ Extra room definitions 多余的区域定义
◆Changed net name 网络名称出现改变
◆Extra
◆Extra
◆Extra
◆Extra net classes 出现多余的网络类 nets 出现多余的网络 pins in nets 网络中出现多余的管脚 rules 网络中出现多余的设计规则
◆Net class with Extra members 网络中出现多余的成员
◆Changed parameter types 改变参数类型
◆Changed parameter value 改变参数的取值
◆Object with extra parameter 对象出现多余的参数。