三星5630 LED灯珠 第二代规格书
11-21USOC S530-XX TR8型号的1206包装LED电路板指南说明书
Technical Data Sheet1206 Package Chip LEDs with Inner Lens11-21USOC/S530-XX/TR8Features˙Package in 8mm tape on 7〞diameter reel.˙Compatible with automatic placement equipment. ˙Compatible with infrared and vapor phase reflowsolder process. ˙Mono-color type.Descriptions˙The 11-21 SMD Taping is much smaller than lead frame type components, thus enable smaller board size, higher packing density, reduced storage space and finally smaller equipment to be obtained.˙Besides, lightweight makes them ideal for miniature applications. etc.Applications˙Automotive: backlighting in dashboard and switch. ˙Telecommunication: indicator and backlighting in telephone and fax.˙Flat backlight for LCD, switch and symbol. ˙General use.Device Selection GuideChipMaterial Emitted Color Lens ColorAlGaInPSuper Sunset Orange Water Clear11-21USOC/S530-XX/TR8Notes: Tolerances Unless Dimension ±0.1mm , Angle±0.5°,Unit = mmAbsolute Maximum Ratings (Ta=25℃)Parameter SymbolRatingUnitReverse Voltage V R 5 VForward Current I F 25 mAOperating Temperature Topr -40 ~ +85 ℃Storage Temperature Tstg -40~ +90 ℃Soldering Temperature Tsol 260 (for 5 second)℃Electrostatic Discharge ESD 2000 VPower Dissipation Pd 60 mWPeak Forward Current(Duty 1/10 @1KHz)I F 160 mA11-21USOC/S530-XX/TR8 Electro-Optical Characteristics (Ta=25℃)Parameter Symbol *ChipRankMin. Typ. Max. Unit Condition A2 29 73 -----A3 68 106 -----A4 97 145-----A5 116 184 ----- Luminous Intensity IvA6 145 223 -----mcd I F=20 mA Viewing Angle2θ1/2 ----- ----- 60 ----- deg I F=20mA Peak Wavelengthλp ----- ----- 621 ----- nm I F=20mA Dominant Wavelengthλd----- ----- 615 ----- nm I F=20mA Spectrum RadiationBandwidth△λ----- ----- 20 ----- nm I F=20mA Forward Voltage V F----- ----- 2.0 2.4 V I F=20mA Reverse Current I R ----- ----- ----- 10 μA V R=5V *11-21USOC/S530-XX/TR8Chip RankLoaded quantity per reel 2000 PCS/reel Notes: Tolerances Unless Dimension ±0.1mm , Angle±0.5°,Unit = mm11-21USOC/S530-XX/TR8 Typical Electro-Optical Characteristics Curves11-21USOC/S530-XX/TR8 Reliability Test Items And ConditionsThe reliability of products shall be satisfied with items listed below. Confidence level : 90 % LTPD : 10 %No. Items Test Condition Test Hours/Cycles SampleSizeAc/Rc1 Reflow Temp. : 240℃±5℃Min. 5 sec. 6 min. 22 Pcs. 0/12 Temperature Cycle H : +85℃ 30min.∫ 5 min.L : -55℃ 30min. 50 Cycles 22 Pcs. 0/1 3 Thermal Shock H : +100℃ 5min.∫ 10 sec.L : -10℃ 5min.50 Cycles 22 Pcs. 0/1 4High TemperatureStorage Temp. : 100℃ 1000 Hrs. 22 Pcs. 0/1 5Low TemperatureStorage Temp. : -55℃ 1000 Hrs. 22 Pcs. 0/1 6 DC Operating Life I F = 20 mA 1000 Hrs. 22 Pcs. 0/1 7 High Temperature/ High Humidity85℃/R.H85%1000 Hrs.22 Pcs.0/111-21USOC/S530-XX/TR8Precautions For Use 1. Over-current-proofCustomer must apply resistors for protection , otherwise slight voltage shiftwill cause big current change ( Burn out will happen ).2. Storage time2.1 The operation of Temperature and RH are : 5℃~35℃, RH60%. 2.2 Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life , we suggest our customers to use our products within a year(from production date).2.3 If opened more than one week in an atmosphere 5℃~35℃, RH 60%, they should be treated at 60℃±5℃for 15hrs.2.4 When you discover that the desiccant in the package has a pink color (Normal = blue) , you should treat them in the same conditions as 2.3.Soldering heat Reflow Temp / TimeSoldering IronBasic spec is ≦5 sec when 260℃.If temperature is higher, time should be shorter (+10℃→ -1sec). Power dissipation of Iron should be smaller than 15 W , and temperature should be controllable. Surface temperature of the device should be under 230 ℃.11-21USOC/S530-XX/TR8 Rework1. Customer must finish rework within 5 sec under 245℃.2. The head of iron can not touch copper foil.。
三星5630二代灯珠规格书
W1, W2, W3, W4, W5, W6, W7, W8, W9, WA, WB, WC, WD, WE, WF, WG
W5, W6, W7, W8, W9, WA, WB, WC
W6, W7, WA, WB
V1, V2, V3, V4, V5, V6, V7, V8, V9, VA, VB, VC, VD, VE, VF, VG
SAMSUNG ELECTRONICS
95, Samsung2-Ro, Giheung-Gu, Yongin-City, Gyeonggi-Do 446-711, KOREA
1 / 48
Contents
1. Product Code Information 2. Characteristics 3. Typical Characteristics Graph 4. Outline Drawing & Dimension 5. Reliability Test Items & Conditions 6. Solder Conditions 7. Tape & Reel 8. Label Structure 9. Packing Structure 10. Precaution For Use 11. Hazard Substance Analysis Report Revision History
Q1, Q2, Q3, Q4, Q5 Q6, Q7, Q8, Q9, QA
Q1, Q2, Q3, Q4, Q5, Q6
P1, P2, P3, P4, P5 P6, P7, P8, P9, PA
P1, P2, P3, P4, P5, P6
5 / 48
2) Chromaticity Region & Coordinates
SAW8KG0B-高压5630
ESD Protection Device
[Note] Package Forward Current is 20mA
REV.04 August 2013
서식번호 : SSC-QP-7-07-18 (Rev.00)
TZe-cPhonwiecralLEDDatXa10S4h9e0et
Color Correlated Temperature Viewing Angle [2] Color Rendering Index*
ESD (HBM)
Thermal resistance [3]
Symbol VF VR Iv Iv CCT
2Θ1/2 Ra
RthJS
Condition IF=20mA IR=10mA IF=20mA
2. Characteristics of SAW8KG0B
Electro-Optical characteristics
(Ta=25℃)
Parameter Forward Voltage* Reverse Voltage Luminous Intensity*[1] (3700~7000K) Luminous Intensity*[1] (2600~3700K)
0.020
Forward Current(A)
0.015
0.010
0.005
0.0000
5
10
15
20
25
Forward Voltage [V]
Forward Current–Relative Luminous Intensity characteristics, Ta=25oC
1.4
1.2
Relative Luminous Intensity
OSRAM Opto Semiconductors OSLON LED 5630 产品说明书
Dimensions: [mm]detail AScale - 1,5:1157142S12703Schematic:157142S12703157142S12703157142S12703157142S12703157142S12703157142S12703T e m p e r a t u r eT T T 157142S12703Cautions and Warnings:The following conditions apply to all goods within the product series of Optoelectronic Components of Würth Elektronik eiSos GmbH & Co. KG:General:•This optoelectronic component is designed and manufactured for use in general electronic equipment.•Würth Elektronik must be asked for written approval (following the PPAP procedure) before incorporating the components into any equipment in fields such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network, etc. where higher safety and reliability are especially required and/or if there is the possibility of direct damage or human injury.•Optoelectronic components that will be used in safety-critical or high-reliability applications, should be pre-evaluated by the customer. •The optoelectronic component is designed and manufactured to be used within the datasheet specified values. If the usage and operation conditions specified in the datasheet are not met, the wire insulation may be damaged or dissolved.•Do not drop or impact the components, the component may be damaged•Würth Elektronik products are qualified according to international standards, which are listed in each product reliability report. Würth Elektronik does not warrant any customer qualified product characteristics beyond Würth Elektroniks’ specifications, for its validity and sustainability over time.•The responsibility for the applicability of the customer specific products and use in a particular customer design is always within the authority of the customer. All technical specifications for standard products also apply to customer specific products.Product specific:Soldering:•The solder profile must comply with the technical product specifications. All other profiles will void the warranty.•All other soldering methods are at the customers’ own risk.Cleaning and Washing:•Washing agents used during the production to clean the customer application might damage or change the characteristics of the optoelectronic component body, marking or plating. Washing agents may have a negative effect on the long-term functionality of the product.•Using a brush during the cleaning process may break the optoelectronic component body. Therefore, we do not recommend using a brush during the PCB cleaning process.Potting:•If the product is potted in the customer application, the potting material might shrink or expand during and after hardening. Shrinking could lead to an incomplete seal, allowing contaminants into the optoelectronic component body, pins or termination. Expansion could damage the components. We recommend a manual inspection after potting to avoid these effects.Storage Conditions:• A storage of Würth Elektronik products for longer than 12 months is not recommended. Within other effects, the terminals may suffer degradation, resulting in bad solderability. Therefore, all products shall be used within the period of 12 months based on the day of shipment.•Do not expose the optoelectronic component to direct sunlight.•The storage conditions in the original packaging are defined according to DIN EN 61760-2.•For a moisture sensitive component, the storage condition in the original packaging is defined according to IPC/JEDEC-J-STD-033. It is also recommended to return the optoelectronic component to the original moisture proof bag and reseal the moisture proof bag again. •The storage conditions stated in the original packaging apply to the storage time and not to the transportation time of the components. Packaging:•The packaging specifications apply only to purchase orders comprising whole packaging units. If the ordered quantity exceeds or is lower than the specified packaging unit, packaging in accordance with the packaging specifications cannot be ensured. Handling:•Violation of the technical product specifications such as exceeding the nominal rated current, will void the warranty.•The product design may influence the automatic optical inspection.•Certain optoelectronic component surfaces consist of soft material. Pressure on the top surface has to be handled carefully to prevent negative influence to the function and reliability of the optoelectronic components.•ESD prevention methods need to be applied for manual handling and processing by machinery.•Resistors for protection are obligatory.•Luminaires in operation may harm human vision or skin on a photo-biological level. Therefore direct light impact shall be avoided. All products are additionally certified as risk groups 0 to 2 according to DIN EN 62471:2008.•In addition to optoelectronic components testing, products incorporating these devices have to comply with the safety precautions given in IEC 60825-1, IEC 62471 and IEC 62778•Please be aware that Products provided in bulk packaging may get bent and might lead to derivations from the mechanical manufacturing tolerances mentioned in our datasheet, which is not considered to be a material defect.Technical specification:•The typical and/or calculated values and graphics of technical parameters can only reflect statistical figures. The actual parameters of each single product, may differ from the typical and/or calculated values or the typical characteristic line.•On each reel, only one bin is sorted and taped. The bin is defined on intensity, chromaticity coordinate or wavelength and forwardWürth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODPLD001.0022023-05-27DIN ISO 2768-1mDESCRIPTIONWL-T7DS 7 Segments Display THTSingle Digit ORDER CODE157142S12703SIZE/TYPE BUSINESS UNIT STATUS PAGEvoltage.•In order to ensure highest availability, the reel binning of standard deliveries can vary. A single bin cannot be ordered. Please contact us in advance, if you need a particular bin sorting before placing your order.•Test conditions are measured at the typical current with pulse duration < 30ms. •Wavelength tolerance under measurement conditions ± 2nm. •Optical intensity tolerance under measurement conditions ±15%. •Forward voltage tolerance under measurement conditions ± 0.2V.These cautions and warnings comply with the state of the scientific and technical knowledge and are believed to be accurate and reliable.However, no responsibility is assumed for inaccuracies or incompleteness.Würth Elektronik eiSos GmbH & Co. KG EMC & Inductive Solutions Max-Eyth-Str. 174638 Waldenburg GermanyCHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCEPROJECTION METHODPLD001.0022023-05-27DIN ISO 2768-1mDESCRIPTIONWL-T7DS 7 Segments Display THT Single DigitORDER CODE157142S12703SIZE/TYPEBUSINESS UNITSTATUSPAGEImportant NotesThe following conditions apply to all goods within the product range of Würth Elektronik eiSos GmbH & Co. KG:1. General Customer ResponsibilitySome goods within the product range of Würth Elektronik eiSos GmbH & Co. KG contain statements regarding general suitability for certain application areas. These statements about suitability are based on our knowledge and experience of typical requirements concerning the areas, serve as general guidance and cannot be estimated as binding statements about the suitability for a customer application. The responsibility for the applicability and use in a particular customer design is always solely within the authority of the customer. Due to this fact it is up to the customer to evaluate, where appropriate to investigate and decide whether the device with the specific product characteristics described in the product specification is valid and suitable for the respective customer application or not.2. Customer Responsibility related to Specific, in particular Safety-Relevant ApplicationsIt has to be clearly pointed out that the possibility of a malfunction of electronic components or failure before the end of the usual lifetime cannot be completely eliminated in the current state of the art, even if the products are operated within the range of the specifications.In certain customer applications requiring a very high level of safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health it must be ensured by most advanced technological aid of suitable design of the customer application that no injury or damage is caused to third parties in the event of malfunction or failure of an electronic component. Therefore, customer is cautioned to verify that data sheets are current before placing orders. The current data sheets can be downloaded at .3. Best Care and AttentionAny product-specific notes, cautions and warnings must be strictly observed. Any disregard will result in the loss of warranty.4. Customer Support for Product SpecificationsSome products within the product range may contain substances which are subject to restrictions in certain jurisdictions in order to serve specific technical requirements. Necessary information is available on request. In this case the field sales engineer or the internal sales person in charge should be contacted who will be happy to support in this matter.5. Product R&DDue to constant product improvement product specifications may change from time to time. As a standard reporting procedure of the Product Change Notification (PCN) according to the JEDEC-Standard inform about minor and major changes. In case of further queries regarding the PCN, the field sales engineer or the internal sales person in charge should be contacted. The basic responsibility of the customer as per Section 1 and 2 remains unaffected.6. Product Life CycleDue to technical progress and economical evaluation we also reserve the right to discontinue production and delivery of products. As a standard reporting procedure of the Product Termination Notification (PTN) according to the JEDEC-Standard we will inform at an early stage about inevitable product discontinuance. According to this we cannot guarantee that all products within our product range will always be available. Therefore it needs to be verified with the field sales engineer or the internal sales person in charge about the current product availability expectancy before or when the product for application design-in disposal is considered. The approach named above does not apply in the case of individual agreements deviating from the foregoing for customer-specific products.7. Property RightsAll the rights for contractual products produced by Würth Elektronik eiSos GmbH & Co. KG on the basis of ideas, development contracts as well as models or templates that are subject to copyright, patent or commercial protection supplied to the customer will remain with Würth Elektronik eiSos GmbH & Co. KG. Würth Elektronik eiSos GmbH & Co. KG does not warrant or represent that any license, either expressed or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, application, or process in which Würth Elektronik eiSos GmbH & Co. KG components or services are used.8. General Terms and ConditionsUnless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms and Conditions of Würth Elektronik eiSos Group”, last version available at .Würth Elektronik eiSos GmbH & Co. KGEMC & Inductive SolutionsMax-Eyth-Str. 174638 WaldenburgGermanyTel. +49 (0) 79 42 945 - 0*******************CHECKED REVISION DATE (YYYY-MM-DD)GENERAL TOLERANCE PROJECTIONMETHODPLD001.0022023-05-27DIN ISO 2768-1mDESCRIPTIONWL-T7DS 7 Segments Display THTSingle Digit ORDER CODE157142S12703SIZE/TYPE BUSINESS UNIT STATUS PAGE0.56"eiPal PCN11/11This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use. Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation, transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.。
三星GT-S5630s说明书
网址中国印刷编码：GH68-24083A 中文 08/2009 版本 1.1GT-S5630C 使用说明书使用本说明书感谢您购买三星手机。
本手机基于三星高科技和高标准，为您提供高品质的移动沟通和娱乐。
本使用说明书专门用于指导您使用手机的功能。
如欲迅速使用手机，请参阅“手机简介”、“手机的安装和准备”以及“使用基本功能”。
•使用手机之前，请先仔细阅读本使用说明书，以确保安全和正确使用。
•本使用说明书中的描述基于手机的默认设置。
指示图标在开始使用前，请先熟悉本使用说明书中的图标：警告-可能伤及自己或他人。
小心-可能损坏手机或其它设备。
注意-注释、使用提示或附加信息。
X参阅-具有相关信息的页面。
例如：X第 12 页（表示“参阅第 12 页”）。
警告小心ii使用本说明书iii版权信息本手机所采用的全部技术和产品的所有权归各自的所有人所有：•Bluetooth ® 是全球各地 Bluetooth SIG 公司的注册商标——蓝牙 QD ID ： B015423。
•Windows Media Player ® 是 MicrosoftCorporation 的注册商标。
→下一步-为执行步骤必须选择的选项或功能表的次序。
例如：在功能表模式下，选择信息 → 新建信息（表示信息，下一步新建信息）。
[]方括号-手机按键。
例如：[]（表示电源开/关/结束键）。
iv目录安全和使用信息 (2)安全警告 .......................................2安全注意事项 ..................................4重要使用信息 . (6)手机简介 .....................................10配件介绍 .....................................10手机部位图 ..................................11按键 ...........................................12图标 ...........................................12手机的安装和准备 ..........................14安装 SIM 或 USIM 卡以及电池 ..........14电池充电 .....................................16插入存储卡（选配） .. (17)使用基本功能 ................................18开机和关机 ..................................18使用触摸屏 ..................................19使用功能表 . (19)目录v切换应用程序 .................................20使用小组件 ...................................20自定义手机 ...................................21使用基本通话功能 ...........................22发送和查看信息 ..............................23添加和查找联系人 ...........................27使用基本照相机功能 ........................28收听音乐 ......................................29浏览 WAP ....................................30使用中国移动通信服务 . (31)使用高级功能 ...............................34使用高级通话功能 ...........................34使用高级电话簿功能 ........................37使用高级信息功能 ...........................38使用高级照相机功能 ........................39使用高级音乐功能 (41)使用工具和应用程序 .......................44使用蓝牙无线功能 (44)启动手机追踪 .................................46录制和播放语音备忘录 ......................46编辑图片 ......................................47打印图片 ......................................49创建和查看世界时间 ........................49设定和使用闹钟 ..............................50使用计算器 ...................................51货币或测量单位换算 ........................51设定倒计时计时器 ...........................51使用秒表 ......................................51新建任务 ......................................52创建文本备忘录 ..............................52管理日历 .. (52)功能表功能概述 ...............................a 故障排除 .......................................b安全和使用信息请遵守下列注意事项，以免出现危险或非法情况，并确保手机性能最佳。
Sunnydaze Decor 2-Pack 外星人星星 LED灯说明书
Thank you for choosing Sunnydaze Decor. We stand behind our brand and the quality of the items we sell. Replacement parts or products will be sent at our discretion within the 1-year warranty period. Proof of purchase, with the date of purchase as well as photos of the merchandise defect must be provided. Photos are used to determine the cause of defects and for future quality control.If you have any questions, comments or concerns, feel free to contact us by phone at 888-881-4668, by email: **********************************, or via our contact us page at /contact-us/SOLAR STAKE LED STARBURST LIGHT ,2-PACKINA-385Please read this manual carefully before use and keep it for future reference.03/2019SL-3865Page 1 / 2 CHOOSING THE RIGHT LOCATION• Select an outdoor location where the solar panel will receive at least 6-8 hours of full, direct sunshine each day. Ensure the solar panel is not being shaded by tree, shrub or building shadows throughout the day as this will influence the charge of the battery and shorten the working time at night.• Avoid locations with strong nighttime light sources nearby, such as street or porch lights, as it may cause the light to turn off due to the light detecting sensor receiving too much ambient light.• Before mounting the stakes into the ground, make sure the soil is softened. Hard soil may damage or break the stake.ASSEMBLY & OPERATION1. Carefully unpack your solar light from the box.2. Push the top and bottom stake pieces firmly together.3. Insert the stake into the ground, ensuring it is stable and will not fall over.4. Switch the power button on the solar panel to the 'ON' position.5. Arrange the flexible light branches as desired.6. First Time Use: The solar light will require at least 8 hours of full and direct sunlight to fully charge the battery. Make sure the unit is turned on while charging.7. As long as the battery has a sufficient charge, the product will automatically illuminate when it gets dark, and turn off during the day.HOW SOLAR LIGHTS WORKDuring the day, the solar panel converts solar energy into electricity and stores it in the rechargeable battery. At night, the light turns on automatically via a light detecting sensor built into the unit. How long the light illuminates will depend upon the location of the light, weather conditions, and how much direct sunlight the unit is exposed to. Ensure the power is switched to 'ON' while charging.03/2019SL-3865Page 2 / 2 ACCESSING AND CHANGING THE BATTERY1. Switch the power OFF.2. Carefully remove the screws on the bottom of the battery housing.3. Gently remove the old battery.4. Paying attention to the positive and negative terminals, gently insert the new battery.5. Carefully reassemble the battery housing.6. The solar light will require at least 8 hours of full, direct sunlight to fully charge the batte ry.REPLACING THE BATTERYThe battery, like all rechargeable batteries, has a limited life span, and become less efficient with repeated charge/discharge cycles. As the capacity of the battery reduces over time, you will notice reduced operating time and will need to replace the battery.Only use compatible rechargeable batteries, alternatives may be incompatible which may damage the system and will void the warranty.Dispose of the batteries in accordance with local laws and regulations.。
LED灯条芯片处理指南说明书
4) LEDs must be stored in a clean environment. If the LEDs are to be stored for three months or more after being shipped from Samsung, they should be packed with a nitrogen-filled container (shelf life of sealed bags is 12 months at temperature 0~40 ºC, 0~90 % RH).
▶ Handling
DO NOT allow stacking
DO NOT allow finger touch or Sharpen/Hard Object
※ Horizontally and Vertically direct force might cause fatal damage during manufacturing process of luminaire.
2/2
This document contains tentative information, the contents may change without notice.
1/2
This document contains tentative information, the contents may change without notice.
1) For over-current protection, users are recommended to apply resistors connected in series with the LEDs to mitigate sudden change of the forward current caused by shift of forward voltage.
ColorReach Powercore gen2 高性能外部长投光RGBLED灯说明书
• Integrates patented Powercore gen2 technology that controls power output to fixtures directly from line voltage—rapidly, efficiently, and accurately. The Philips Color Kinetics Data Enabler Pro merges line voltage with control data and delivers them to fixtures over a single standard cable, dramatically simplifying installation and lowering total system cost.
Die-cast aluminium, powder-coated finish
Lens
Tempered glass
Fixture Connections
Integral male/female waterproof connectors
Temperature Ranges
-40° – 50° C (-40° – 122° F) Operating -20° – 50° C (-4° – 122° F) Startup -40° – 80° C (-40° – 176° F) Storage
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Rev:ISSUE NO :LED APPROVEDApproved rank :V F (AZ,A1,A2,A3,A4)CIE(P1,P2,P3,P4,P5,P6,P7,P8,P9,PA)I (S1,S2,S3)Contents1.Product Outline----------------------------------------------32.Absolute Maximum Rating-------------------------------33.Characteristics----------------------------------------------34.Chromaticity Diagram-------------------------------------45.Typical Characteristic Graph----------------------------56.Outline Drawing&Dimension--------------------------67.Reliability Test Items&Conditions-------------------78.Solder Conditions--------------------------------------------89.Taping Dimension--------------------------------------------9bel Structure-----------------------------------------------1011.Lot Number----------------------------------------------------1012.Reel Packing Structure------------------------------------1113.Aluminum Vinyl Bag-----------------------------------1214.Precaution For Use-----------------------------------------1315.Hazard Substance Analysis(SGS)------------------1516.Hazard Substance Analysis(SVHC)------------------2117.Revision History----------------------------------------------35P0=P1+P2+P3+P4+P5+P6+P7+P8+P9+PAV F CIE I vP7,P8,P9,PA S1,S2,S35.Typical Characteristics Graph*These graphs show typical values.(Ts :25℃)(I F =65mA)(I F =65mA)Anode MarkLand PatternRecommended8.Solder Conditions1)Reflow Conditions(Pb Free)Reflow Frequency:2times max.2)For Manual SolderingNot more than5seconds@MAX300℃,under soldering iron.9.Taping DimensionPKG direction in carrier tape pocketAnode Mark(Cutting)Quantity:The quantity/Reel to be Max.2,000pcs,.Cumulative Tolerance:Cumulative tolerance/10pitches to be±0.2㎜Adhesion Strength of Cover Tape:Adhesion strength to be0.1-0.7N when the tape is turned off from the carrier tape at10℃angle to be the carrier tape.Packaging:P/N,Manufacturing data code no.and quantity to be indicated ondamp proof Package.LEVEL 2aAZP1S1SPMWHT541MD5WAP0S0AZP1S101II I IIIIIII I IIIIIII III III II IIIIII I IIIIIII I IIIIIIIIGLAW94001/1001/2,000pcsIIIIII I IIIIIII III IIII I III I III I III III IIIIII Silica gel&Humidity Indicator Card in Aluminum Vinyl Bag14.Precaution for Use(취급상주의사항)1)For over-current-proof function,customers are recommended to apply resistors toprevent sudden change of the current caused by slight shift of the voltage. 과전류방지를위해전압의미세한이동에의해야기되는전류의순간변화를방지하기위해저항등의설치를권장함.2)This device should not be used in any type of fluid such as water,oil,organicsolvent,etc.When washing is required,IPA is recommended to use. 제품은물,오일,유기물과같은액체타입에서의사용은제한되며,세정이필요할시에는IPA사용을권장함.3)When the LEDs illuminate,operating current should be decided after considering theambient maximum temperature. LED의발광시,동작전류는주변최고온도를고려하여결정되어야함.4)LEDs must be stored in a clean environment.If the LEDs are to be stored for3months or more after being shipped fromSamsung Electronics,they should be packed by a sealed container with nitrogen gas injected.(Shelf life of sealed bags:12months,temp.~40℃,~90%RH)LED의보관은청정한환경에서보존되어져야하며,만약삼성전자로부터공급받는후3개월또는그이상보관이필요하다면질소가스를동봉한보존용기에보관되어야함.(보존bag의수명:12개월,보존온도~40℃,습도~90%RH)5)After storage bag is open,device subjected to soldering,solder reflow,or otherhigh temperature processes must be:보존Bag이개봉된후에,납땜이나reflow등의높은온도에노출되는제품은다음의사항에부합되어야함.a.Mounted within672hours(28days)at an assembly line with a condition of nomore than30℃/60%RH,a.제품은30℃/60%RH보다같거나낮은조립조건에서672시간(28일)이내에조립해야함.b.Stored at<10%RH.b.10%이하의상대습도에서보관되어야함.6)Repack unused Products with anti-moisture packing,fold to close any opening andthen store in a dry place.사용하지않은제품은방습팩에넣어개봉부위를닫아서다시포장한후,건조한장소에서보관할것을권장함.7)Devices require baking before mounting,if humidity card reading is>60%at23±5℃. 만약습도표시카드의수치가23±5℃에서60%이상이라면,제품실장전에baking하여야함.8)Devices must be baked for1hour at65±5℃,if baking is required. 만약baking이필요하다면,제품은65±5℃에서1시간정도baking되어야함.9)The LEDs are sensitive to the static electricity and surge.It is recommended touse a wrist band or anti-electrostatic glove when handling the LEDs.LED는정전기및서지에민감한제품이므로,LED제품을다룰시에는정전기방지장갑이나손목밴드를사용하기를권장함.If voltage exceeding the absolute maximum rating is applied to LEDs,it may cause damage or even destruction to LED devices.만약절대허용치를초과하는전압이LED에가해지면,LED소자는파괴되거나손상될수있음.Damaged LEDs may show some unusual characteristics such as increase in leakcurrent,lowered turn-on voltage,or abnormal lighting of LEDs at low current.손상된제품은누설전류의증가,Turn on전압의저하,저전류에서의점등불량등의이상거동을보일수있음.10)Risk of Sulfurization(or Tarnishing)Samsung Electronic's lead frame based package products(such as mid power and HV AC)contain silver(Ag)plated lead frames.Silver may turn black(or tarnish)when exposed to substances such as sulfur,chlorine,or other halogen compounds.삼성전자의리드프레임은Ag(은)을도금한Package제품입니다.황(S),염소(Cl),또는다른할로겐화합물들에노출시Ag(은)은검정(또는어두운색)으로바뀔수있으니주의바랍니다.Sulfurization of the lead frame may result in reduction of lumen output,color shift and an open circuit in some extreme cases.리드프레임의황화(Sulfurization)는광량저하,색좌표변화및심한경우회로내의LED무등(Open)불량을일으킬수도있습니다.Do not store or use such lead frame LED's together with oxidizing substances listed above.The following examples could be sources of such substances:rubber,corrugate paper,solder cream etc.LED를아래의목록으로만들어진산화성물질들과함께리드프레임을저장하거나사용하지마십시오.황화(Sulfurization)의근원일수있습니다.:고무,일반종이,남땜크림등15.Hazard Substance Analysis-SGS16.Hazard Substance Analysis-SVHC(REACH)。