proE的config配置文件中文解释
ProE系统配置config解释
Pro/Engineer Config.Pro & .DTL 配置文件环境变量说明Pro/E环境变量是用来设置Pro/E的工作环境的，你可以在config.pro文件里进行设置。
您可以按开头字母查找。
A B C D E F G H I K L M N O P Q R S T U V W XThis document contains a list of configuration options, in alphabetical order, showing for each option or group of related options:•Configuration option name.•Associated variables or values. The default values for the options are shown in italics. •Product type for which the option is used, if the option is specific to one type (for example, Layout, Assembly, Part, Drawing, and so on).•Brief description.accuracy_lower_boundvalue (between 1.0e-6 and 1.0e-4)Enter an accuracy value to override the default lower limit of 0.0001. The upper limit is fixed at 0.01.add_weld_mpyes, no•“yes”—the system includes welds when calculating mass properties.•“no”—the system excludes welds when calculating mass propertiesallow_confirm_windowyes, noDisplay a confirmation window when exiting Pro/ENGINEER. This enables you to use the mouse to confirm/cancel exiting Pro/ENGINEER.allow_move_view_with_moveyes, noWhen set to “yes,”allows the Move command in Drawing mode to move drawing views. allow_cycle_optimizeyes, noPrior to Release 18.0, there was a sequence parameter for holemaking that allowed users to optimize the cycle output to CL-data of holemaking sequences. This parameter has not been available since Release 18.0.•yes—makes the parameter visible in the sequence•no—the parameter is not visible in the sequenceallow_mod_attach_draft_dimyes, no•"no"—A #Detail, #Mod Attach is obsolete for draft feature dimensions; use #Detail, #Move to move the placement of the dimension along the same edge.•"yes"—When performing a #Detail, #Mod Attach to a draft feature dimension, you can select a different edge of the same feature to which to attach the dimension. The available edges for selection highlight in magenta.allow_move_attach_in_dtl_moveyes, noDetermines if the Move and Move Attach commands in drawing mode act together (yes) or not (no).allow_old_style_roundyes, noDetermines which round-creation functionality the system uses.•“yes”—Uses old (Release 16.0) functionality.•“no”—Uses new functionality.allow_ply_cross_sectionyes, no“yes”—Enables Pro/COMPOSITE to create a cross-section of composite plys.allow_redo_intersectionsyes, no“yes”—Displays the ReIntersect command in the ASSY FEAT menu.allow_ref_scope_changeyes, no“no”—Displays the message “Reference Scope changes are prohibited by the configuration file settings.”when the Ref Scope UI is changed.allow_reps_to_geom_reps_in_drwsyes, noAllows you to create drawing references to geometry representations (including dimensions, notes, and leaders). However, these references might become invalid if the referenced geometry changes. This option is for advanced users who are aware that some references to geometry representations might not update in drawings.allow_rfs_default_gtols_alwaysyes, no•“yes”—Enables RFS/Default gtols to be created even when not permitted by ANSI standard. allow_udf_style_cosm_threadsyes, noDefines the Cosmetic Thread User Interface.•“yes”—Creates a Cosmetic Thread as a UDF.•“no”—Creates a Cosmetic Thread as a Cosmetic Thread feature.ang_dim_in_screenyes no(Part, Assembly, Sketcher)If set to “yes,”and the display is in the default pan/zoom setting (select, in turn, View, Pan/Zoom and Reset), the system checks whether an angular dimension is visible on the screen. If it is not visible, then the system moves the dimension to a location where it is visible.angular_tol_0.0angular_tol_0.00angular_tol_0.000angular_tol_0.0000angular_tol_0.00000angular_tol_0.000000value (integer in range 0-9)Sets the default tolerance for angular dimensions. Each option sets a tolerance for a specific decimal place. The value is the place of the last decimal.angular_tol# tolerance (# is an integer)An alternative format for setting default angular tolerance dimensions. The # value sets the number of decimal places, and the tolerance is the actual tolerance value. For example, “6 0.000025”sets a tolerance to six decimal places, and the default tolerance value is 0.000025. For integer dimensions, the # value is zero, and the tolerance is an integer. For example, “0 1”sets a tolerance of 1 for integer dimensions.These values affect only models created after the tolerance options are specified in the configuration file. Any subsequent modifications to these options affect only new models that are created after the option modification.ang_unitsang_deg, ang_min, ang_secSets the display of angular dimensions to decimal degrees (ang_deg), degrees and decimal minutes (ang_min) or degrees, minutes and decimal seconds (ang_sec).assy_mfg_open_modeauto_assembly_with_layoutsyes, no(Layout)•“yes”—Enables automatic assembly.•“no”—Disallows automatic assembly.auto_associate_dimensionsyes, noIf this option is set to “yes,”and the drawing setup option “associative_dimensioning”is also set to “yes,”the system tries to associate imported IGES dimensions (not yet associative) with corresponding imported geometry.auto_convert_cablesyes, noWhen regenerating a pre-Release 11.0 cabling assembly the system, by default, automatically creates a separate spool feature for every individual wire or cable in the assembly.“no”—An interface for the cable conversion appears.auto_regen_viewsyes, no•“yes”—Automatically repaints the drawing display when you change from one window to another, for example, when you modify a model in a subwindow while you are working on a drawing in the Main Window. You can repaint or regenerate the drawing to reflect changes made to the model. When you regenerate it, the model updates to changes made in the drawing. •“no”—You can update the drawing only by choosing Regen View from the View menu in the Pro/ENGINEER menu bar and Pick View, Current Sheet, or All Sheets. Neither the Repaint command in the View menu nor the Regenerate command in the DRAWING menu update the drawing when you have this option set to “no,”even if you make the change to the model in Drawing mode (such as modifying a dimension value). You can select as many views as you want to regenerate at the same time.axis_displayyes, noDisplays or hides datum axes and their names.bellyes, noTurns the keyboard bell that “rings”after each prompt on (yes) or off (no). You can override this setting at run time by using the Environment dialog box on the Utilities menu.bitmap_size250, valueWorks in conjunction with save_bitmap. Determines the size (squared) of the bitmap image that is stored.blank_layervalueBlanks specified layers when you begin a Pro/ENGINEER session. The value is the layer ID. Notes:•This is valid for layer IDs 1 - 32 only.•This is provided for compatibility of pre-Release 9.0 objects. Once the object is stored in Release 9.0 or later, this option is no longer necessary.bom_formatformatname.fmtSets the BOM format file to be used for a customized BOM.button_name_in_helpyes, noWhen set to “yes,”the name and menu of any selected menu option displays, in English, in the help text associated with that button.cadam_line_weightslight, medium, heavyDefine the line width of entities within Pro/ENGINEER in order to plot drawings with correct line weights that are consistent with a standard. The default Pro/ENGINEER values for these weights are:•Light—.2•Medium—.3•Heavy—.5If you want to plot a drawing with imported CPTR data and use default line weights, set the configuration option to look like the following example:capped_clipyes, no•“yes”—Displays the model as a sollid when shaded and clipped.“no”—Displays the model as surfaces when shaded and clipped.cadam_line_weights .2 .3 .5campost_dirpathnameSpecifies the CAM-Post load point directory to enable you directly set-up the post-processors and generate MCD files.catia_out_to_existing_modelappend, overwrite•“append”—if selected CATIA model already exists, the new data is appended to the existing CA TIA file.•“overwrite”—if selected CATIA model already exists, the newly exported file overwrites the existing one.cdt_transfer_detailsno, yesUsed when importing a CADAM drawing:•“no”—Details (dittos) associated with the CADAM drawing are placed on the current Pro/ENGINEER drawing sheet only; no extra sheets are added.•“yes”—Details (dittos) associated with the CADAM drawing are converted into separate additional sheets on the Pro/ENGINEER drawing. Thus, the drawing has as many sheets added as there are dittos transferred.chk_part_surfs_profpockno, yes•yes—Includes all reference part surfaces as Check Surfaces for Profiling and Pocketing NC sequences (the default is “no”).cgm_inc_pad_byte_in_lengthyes, no•“yes”—Enables a metafile to be processed by the Micrographic CGM converter.cgm_use_enum_in_real_specyes, no•“yes”—Enables a metafile to be viewed in Advanced Technology Center’s ForReview. cgm_use_reversed_ieee_floatsyes, no•“yes”—Enables a metafile to be viewed in Advanced Technology Center’s ForReview. chamfer_45deg_dim_textASME/ANSI, ISO/DIN, JISControls the display of chamfer dimension text without affecting the leader. This only affects the text of newly created dimensions. ASME/ANSI is the default. The others affect text as follows: clip_alwaysyes, nocl_arrow_scalepositive number (default = 1)This option enables you to control the size of the tool path arrow for Contouring NC sequences. “0”—The arrow does not display.Any other value—The arrow scales accordingly.clockyes, noTurns the clock display (which shows that Pro/ENGINEER is working) on and off.clr_print_plus_minusyes, noSets the display of the system accuracy when calculating clearances between two parts or surfaces. The default is to not display the accuracy.coloron, offTurns the colors on or off. Turning colors off displays the model wireframe in white.color_ramp_sizeinteger valueSpecifies the number of shades in a color ramp used to show shading of colored objects. This applies only to systems with 256 color graphics and with color maps that compress.color_resolution0.1, epsilon valueCompares colors to see if two colors are close in RGB values by an epsilon of 0.1. This has to do mostly with user-defined colors. If this value is decreased, it could allow for more colors to be defined which are very similar in RGB definition.color_windowsall_windows, one_windowControls the display of colors in the main and auxiliary windows.•“all_windows”—Wireframe colors display in the main window and all auxiliary windows. •“one_window”—Colors display only in the main window. Auxiliary windows display wireframe in the default color.comp_assemble_startconstrain_in_window, packageControls where new assembly components are initially shown.•“constrain_in_window”—Components are shown in a seperate window and must be constrained within the assembly.•“package”—Components are shown within the assembly as a packed component.comp_rollback_on_redefyes, no“no”—Assembly is not rolled back when the user redefines a component.company_nameyour company nameThis option is used with the export option “iges_out_mil_d_28000.”To support MIL-D-28000, your company name is required input and the system prompts you every time you export through IGES unless you set the company name in your configuration file.compress_output_filesyes, noObject files can be stored in a compressed format as a space-saving effort. Compressed files are slower to read and write, but are one-half to one-third the size. They are also fully compatible across systems.•“yes”—Stores object files in compressed format.•“no”—Object files are not compressed.Note: If you want to copy a compressed object file from a UNIX system to a Windows (NT or 95) machine or vice versa, use the operating-system command “rcp -b”from the Windows machine. copy_dxf_dim_pictyes, noThis option enables exact look-alikes of AutoCAD drawings to be made when AutoCAD drawings are imported to Pro/ENGINEER through a DXF file.•“yes”—A look-alike is created, and all entities in the AutoCAD drawing appear in Pro/ENGINEER. Each of these entities is independent of any others in the drawing. •“no”—Only dimensions and geometry are imported, and all entities behave as if they were created in Pro/ENGINEER.copy_geom_update_pre_2000i_depyes, noWhen set to “yes,”flags independent copy geom features in a pre-2000i model as “modified”when retrieved into Pro/ENGINEER. This enables you to save the model immediately to update the model’s copy geom dependency information. This information has changed in Release 2000i for improved interpretation of references in Pro/PDM and Pro/INTRALINK.cpus_to_usecreate_drawing_dims_onlyyes, noDetermines whether the system saves all dimensions created in Drawing mode in the part or in the drawing as associative draft dimensions.“yes”—Saves all new dimensions created in the drawing inside the drawing as associative draft dimensions. Dimensions created in a drawing that reference part geometry are always associative regardless of the setting of the drawing setup file option.create_fraction_dimyes, no“yes”—All dimensions created the display as fractions.create_numbered_layersyes, no“yes”–Creates default layers named 1 through 32 on new models only.c ustom_rainbowstringDefines the colors used with Pro/FEM-POST™graphic models.You can specify the colors blue, black, cyan, magenta, green, yellow, red, and white for the CUSTOM_RAINBOW option. Enter the colors as a single string that uses the “-”(dash) character as a separator. The case of the string is not considered.For example: white-red-yellow-green-magenta-cyan-black-blueThe default scheme is blue-cyan-green-yellow-red-magenta-whitedatum_displayyes, noDisplays or blanks datum planes and their names.datum_point_displayyes, noDisplays or blanks datum points and their names.datum_point_symbolcross, dot (filled), circle, triangle, squareModifies the display of datum point symbols in Part or Assembly mode.datum_point_tag_displayyes, noSets the display of datum point tags to on or off.dazix_default_placement_unitmm, thou, micronSpecifies the units to be used for data imported in Dazix files.dazix_export_mountholeyes, no•“yes”—Causes the MOUNTHLE section of a Dazix file to be processed as a mount hole. •“no”—Causes the mounthole section to be processed as a cut.dazix_z_translationyes, no“yes”—Passes the objects in the “.edn”files through z translation.default_abs_accuracyvalueDefines the default absolute part accuracy.default_ang_dec_places1, value (2 through 14)Specifies the number of decimal places shown in angular dimensions in a drawing.default_dec_placesvalue (default = 2 for non-angular dimensions)Sets the default number of decimal places (0-14) to be displayed in all model modes for non-angular dimensions. It does not affect the displayed number of digits of dimensions as modified using Num Digits. The number of decimal places of dimensions created in Sketcher is controlled by the option “sketcher_dec_places.”default_dim_num_digits_changesyes, noSets the default number of digits displayed in a dimension to the last entered value. If you set this option to “no,”the system defaults to the value specified for the configuration file option “default_dec_places.”default_draw_scalevalue, noSets the default drawing scale for views added with the No Scale command. The value must be greater than 0. If set to “no,”the system does not set a default drawing scale.default_ext_ref_scopeall, none, skeletons, subassembliesSelects the default condition for models which can be externally referenced. •“all”—References any model. For example, you can create external references to any component in an assembly.•“none”—References no models other than the model being modified and those that exist below it on its branch.•“skeletons”—Any component can reference its associated Skeleton model in the component’s assembly. If a Skeleton model is being modified, it can reference the skeleton model of the assembly above the one to which it belongs.•“subassembly”—Allows external references to the model being modified, the models that exist below it, any peer models that the model being modified might have, and models below them. default_fontname, style, point-sizeSets the default font used by Pro/ENGINEER for displays other than the menu bar, menus and their children, and pop-up menus. You can specify the variables in any order. For example, “courier, bold, 14”and “14, courier, bold”have the same effect.Any variable that you leave out uses the standard setting. The standard default font for Unix systems is helvetica, regular, 12. The standard fonts for Windows NT and Windows 95 are inherited from the system settings made with the Control Panel.See also menu_font, popuphelp_font, and fonts_size.default_object_invalid_refsprohibit, copySets the default condition for reference handling in newly created models.•“prohibit”—If you attempt to create an external reference that violates the scope, you receive an error message, and the system aborts action.•“copy”—If you attempt to create an external reference that violates the scope, you receive a warning about the possible violation.You can then either abort the reference creation or explicitly declare such an “out-of-scope”reference. If you declare the reference, its “backup”is copied automatically to the part/assembly and this backup is referenced (changes to the “master reference”are still checked, when it is in session).If later the “master reference”is not in session, and the part with the “backup”reference is retrieved, the reference becomes “temporarily”frozen and uses the backup. When the “master reference”is again in session, the associativity returns. The user can disallow the declaration prompt at any time; in this case, the system creates a “back up”reference automatically for any “out-of-scope”reference.default_object_scope_settingall, none, skeletons, subassembliesSelects the default condition for reference control in a new cobject .•“all”—Reference any model. This is the way the system works today. The user may freely create external references to any component in an assembly.•“none”—Reference no other models. This will not allow any models other than the model being created, and those that exist below it on its branch, to be externally referenced. •“skeletons”—A new component may reference the Skeleton model of the assembly that the component belongs to. If a Skeleton model is being created, it may reference the skeleton model of the Assembly above the one that it belongs to.•“subassembly”—Allow external references to the model being created, the models whichwill exist below it, any peer models that the model being created might have, and models below them. default_ramp_sizeinteger valueSpecifies a number of shades of gray to show shading of non-colored objects.def_layertype_option nameSpecifies default layer names for different types of items. For information about valid type options, see Introduction to Pro/ENGINEER. The variable“name”is the layer name.delete_after_plottingyes, no“yes”—A plot file is automatically deleted from the directory in which it resides when it has been successfully plotted.depthcue_optionsdepthcue_on, depthcue_offAids in visualizing a wireframe model. With depth cue enabled, wireframe lines become darker as they extend into the screen (in other words, away from you) and lighter as they extend towards the screen (i.e. towards you). Depth cue is supported only by the appropriate graphics hardware. •“depthcue_on”—The default value for the depth cue is set to 50%. It is active all the time. •“depthcue_off”—The default value for the depth cue is set to 0%, i.e., it is effectively disabled, except when you select Depth Cue from the Cosm View menu,diagram_pin_edit_multi_lineyes, no(Diagram)Determines the Pro/TABLE format used when you are modifying pin parameters. •“yes”—You can add user-defined pin parameters by including them between the DEFINE and ENDDEF statements for each pin.•“no”—The system uses columnar format and you cannot add user-defined parameters.dim_fraction_formatstdaiscAffects the appearance of dimension text containing fractions.•“std”—Displays fractional dimensions in the standard Pro/ENGINEER format •“aisc”—Displays fractional dimensions in the American Institute of Steel Construction (AISC) format and displays architectural units according to AISC format for feet-inches dimensions.The table shows AISC format for fractional dimensions:AISC Dimension PTC Dimension10' -2 3/4 10' 2-3/4"10'-0 3/4 10' 3/4"10'-0 10'2 3/4 2-3/4"2 2"3/4 3/4"dim_fraction_denominatorvalue (default = 32)Sets the largest denominator to be used for fractional dimensions. If the fraction can be reduced, then it converts to the lowest possible denominator (for example, 4/32 converts to 1/8).dim_offscreen_limitvalue (default = 1.333)Sets the margin beyond which dimensions are automatically snapped back into the screen. The default value of 1.333 lets a dimension be only a third of the window size outside of the window. The value cannot be less than 1.0.displaywireframe, hiddenvis, hiddeninvis, shadeDisplays model with all lines in white (wireframe), with hidden lines in grey (hiddenvis), or with all hidden lines removed (hiddeninvis). The shade option displays all the models (except drawing mode) with all surfaces shaded (solid & non-solid). Line display is reflected in plotter, DXF and IGES files.display_comps_to_assembleyes, no(Process Assembly)•“yes”—The system brings the whole design model into memory and displays it on the screen. You can then pick process components from either the design model or the Model Tree. •“no”—The system does not bring the whole design model into memory. It displays only the Model Tree. As you pick process components from the Model Tree, the system brings them into memory.display_coordinate_sysyes, noDisplays or blanks coordinate systems and their names.display_dwg_tol_tagsyes, noSets the display of the tolerance tags that appear in drawings. This option does not affect the display of tolerances on dimensions.display_full_object_pathyes, noControls the display of the object’s full file name (including its object-type suffix and its version number) and file path in the window title and Model Info display.•“yes”—Displays full file name and file path.•“no”—Displays object name only.display_in_adding_viewwireframe, minimal_wireframe, defaultControls display of a model in a drawing. This option works when the option “auto_regen_views”is set to “no.”If set to “wireframe,”the system adds each new view in wireframe and displays datums. If set to “minimal_wireframe,”initially displays each new view in wireframe without datums, axes, or silhouette edges. If set to “default,”initially displays the view according to the current setting in the Environment dialog box.display_layervalueThis causes the specified layers to display when you begin a Pro/ENGINEER session. The variable “value”is the layer Id.Notes:This is valid for layer IDs 1 - 32 only.This is provided for compatibility of pre-Release 9.0 objects. Once the object is stored in Release 9.0 or later, this option is no longer necessary.display_silhouette_edgesyes, noSets the display of silhouette edges for wireframe display only.disp_trimetric_dwg_mode_viewyes, noDisplays a model in default orientation when placing a general view on a drawing. If set to “no,”a model does not appear until you choose Default from the Orientation dialog box. However, when you create a drawing view using the default orientation, if you change the setting of this configuration file option, the system does not change the orientation. Once you set a view in the default orientation, the system freezes it.draw_models_read_onlyyes, noSets the files for the models in a drawing to read-only so that you cannot modify them. You cannot add driven dimensions, geometric tolerances, and similar features, to the models. When you attempt to make a change that affects a model, the system issues a warning, and does not make the modification.draw_points_in_model_unitsyes, noDefines the current draft view’s coordinate values as model units rather than drawing units. The GET POINT menu uses the scale of the draft view and the draft view’s model units for relative and absolute coordinate entry and display in the Message Window.drawing_file_editoreditor, protab(Drawing)Specifies the default text editor for editing the drawing setup file. If you do not set this variable, the system uses the default editor. If you set the variable to “protab,”the system uses Pro/TABLE. If you set the variable to “editor,”the system uses the system editor (refer to the option “pro_editor_command”).drawing_setup_filefilename.dtlEstablishes the default drawing setup file option values for any drawing that you create during a Pro/ENGINEER session. If you do not set this option, the system uses the default drawing setup file option values. Certain parameters in the file are valid only if you have a license for Pro/DETAIL.drawing_view_origin_csysname, noUses the named coordinate system as the origin of a newly created view or of a modified view. If you do not want the system to use a coordinate system that you set previously, specify the value as “no.”dwg_select_across_pick_boxyes, noHighlights the Across Box command by default when the PICK MANY menu appears. If you set this option to “no,”the Inside Box command highlights.dxf_out_stroke_textyes, no•“yes”—Strokes out text in DXF or DWG export. Strokes == text is converted to lines and dots.•“no”—Does not stroke out the text for exportecad_area_default_importcosm_area, 3d_volumeDefines how imported ECAD areas are treated.•“cosm_area”—Treats imported ECAD areas as cosmetic area features.•“3d_volume”—Imports ECAD areas with Z-heights as a 3D enclosed quilt.ecad_board_csys_def_namenameSpecifies the default coordinate system name added to an ECAD board being imported. If you do not set this variable, the system prompts you for a name.ecad_comp_csys_def_namenameSpecifies the default coordinate system name added to an ECAD component being imported. If you do not set this variable, the system prompts you for a name.ecad_create_hint_addyes, noAssists in the creation of an ecad_hint.map file.“yes”—Automatically renames components, if necessary, each time a library of component outlines is imported to Pro/ENGINEER.ecad_default_comp_heightvalue unitSets the default value and units for an ECAD component being imported. Units can be:•inch•mil (1E-3 inches)•thou (1E-6 inches)•cm•mm•micron (1E-6 meters)•dsu (1E-8 meters)If you do not set this variable, the system uses the current component’s units.ecad_exp_both_two_areasyes, noSupports the export of ECAD areas with different “Above Board”and “Below Board”conditions.•“yes”—Enables you to export both sided keep-in/keep-out ECAD areas as two individual areas (top and bottom).ecad_export_holes_as_cutsyes, noExports Pro/ENGINEER holes as cuts to ECAD systems.ecad_import_holes_as_featuresyes, noApplies to IDF 2.0 files.Import: All sections specified as DRILLED_HOLE, with either the PTH (Plated Holes) or NPTH (Non-Plated Holes) attribute in an IDF 2.0 file, are imported as “through all”holes. Each such。
proe_config配置中文
no - 序列参数output_point不可用
prompt_on_erase_not_disp yes, no
指定是否显示一个提示，来允许您保存未显示的对象。该选项与“视图”菜单的命令“拭除”>“未显示的”一起使用。
prev_proc_comp_def_color
指定前一步骤中添加至处理组件中元件的缺省颜色。三个小数值，指定了在生成的颜色中，红色、绿色和蓝色（按此顺序）所占的百分比。例如，“0 0 49”指定了中等蓝色。
prev_proc_comp_def_font
solidfont、dotfont、ctrlfont、dashfont、phantomfont=ctrlfont_s_l、ctrlfont_l_l、ctrlfont_s_s、ctrlfont_mid_l、dashfont_s_s、phantomfont_s_s
设置pro/mfg中语法菜单文件的缺省目录。使用完整路径名，以避免出现问题。例如，/home/users/library/mach_cmdsym
pro_nastran_conv <路径名>
指定到可执行的msc nastran 68转换器（msc2anf）的路径。
pro_nastran_path <路径名>
指定到可执行的msc/nastran转换器 (msc2anf) 的路径。
pro_note_dir <目录名>（绘图）
指定目录，从中可检索从文件输入的注释。使用完整路径名，以避免出现问题。例如：/home/users/notefiles。
pro_texture_library 有效路径
Proe Config全部配置文件说明10-07
o v erride_store_back yes, no将检索自其它目录的对象，强制保存到当前工作目录。
yes - 在当前工作目录中保存对像；no -在它们的源目录中保存对象。
如果设置为「no」，并且对源目录没有写许可，则配置选项「save_object_in_current」将起作用。
package_co nstraints update, freeze, disallow指定「组件」模式中对包装组件执行的操作。
Update - 组件改变后，更新组件。
Freeze - 组件改变后，不移动组件。
Disallow - 组件中不允许有包装组件（必须完全约束）。
package_ref_alert yes, noyes - 当存在有对包装组件的参照时，启用警告提示。
parenthesize_ref_dim yes, no在圆括号中，封装参照尺寸。
如果设置为「no」，则参照尺寸之后，带有文本「REF」。
pdm_revpdm_fmt_rev_ver, pdm_fmt_rev, pdm_fmt_branch_rev_ver, pdm_fmt_branch_rev指定系统参数（PDM_REV）的格式。
此选项仅用于提交到Pro/PDM或Pro/INTRALINK的对象。
pen1_line_weightpen2_line_weight、pen3_line_weight、pen4_line_weight、pen5_line_weight、pen6_line_weight、pen7_line_weight、pen8_line_weight、整数（范围1-16）使用静电绘图仪，设置用笔绘制的像素的深浅度。
深浅度的范围是从1（最浅）到16（最深）。
缺省值为：Pen1 4、Pen2 1、Pen3 2、Pen4 3、Pen5 2、Pen6 3、Pen7 1、Pen8 4pen_slew值对于与该选项兼容的绘图仪，在x和y方向，设置笔速。
proe_config配置中文解释5
转换为pro/engineer曲面前，清除和平滑b-样条曲面中的噪声。
tutor_enabled yes, no
yes - 启用“倒圆角向导”。 no - 禁用“倒圆角向导”。
update_harness_mfg_line_color yes no,
template_sheetmetalpart inlbs_part_sheetmetal.prt, empty, <文件名>
指定缺省钣金件零件模型模板的文件名。设定此选项后，即可在当前的pro/engineer进程中立即生效。
设置为empty时，不使用模板。
template_solidpart inlbs_part_solid.prt,empty, <文件名>
允许在温度计型刻度出现时，放置它们，这样它们就不会覆盖pro/engineer窗口（如果空间允许，例如，如果已经缩放了窗口）。
tiff_compression none，g4
确定是否要使用g4压缩来处理至tiff的输出
tiff_type palette，rgb，grayscale，mono
三个小数值（范围是 0-100 ）
指定pro/engineer使用的颜色。可将这些颜色赋予其缺省值以外的值。三个小数值，指定了在生成的颜色中，红色、绿色和蓝色（按此顺序）所占的百分比。例如，“0 0 49”指定了中等蓝色。
system_iges_header_file 文件名
向iges 文件的“开始”部分插入一个指定的文本文件（有关更多 信息 ，请参阅“user_iges_header_file”）。当与“user_iges_header_file”一起使用时，首先出现系统文本。
proe config全部配置文件说明
21关于配置文件选项为配置文件输入所需的设置，可以预设环境选项和其它全局设置。
要设置配置文件选项,使用“选项”对话框（“实用工具"〉“选项”）。
本帮助模块含有一个按字母顺序显示每一选项或相关选项组的配置选项列表：·配置选项名称。
·相关变量或值。
选项的缺省值显示为斜体.·简单说明。
accuracy_lower_bound 数值(在1。
0e—6和1。
0e—4之间）输入一个精确值来覆盖缺省下限0。
0001.上限固定为0.01add_java_class_path 〈搜索路径>此选项涉及到有关JA V A环境变量CLASSPATH的选项值,它用于查找J-Link程序中使用的类.可在同一行上指定多个搜索路径，在UNIX中用“："隔开，在Windows NT中用“;"隔开.设定此选项后,启动第一个J—Link应用程序时才会生效add_weld_mp yes，noyes —系统在计算质量属性时，包括焊接。
no —系统在计算质量属性时，排除焊缝。
allow_anatomic_features yes, no将此配置文件现象设置为yes，使得下列选项可用：“扭曲"菜单中:“局部拉伸”、“半径圆顶”、“截面圆盖”、“耳”、“唇”.“实体"菜单中:“开槽"、“轴肩"、“凸缘”、“退刀槽”。
“基准"菜单中:“计算".allow_cycle_optimize yes，no在18。
0以前的版本中,有一个孔加工序列参数，允许用户优化孔加工序列CL-数据的循环输出。
自版本18。
0以来，该参数不再有效。
yes —使该参数在序列中可见no - 该参数在序列中不可见allow_move_attach_in_dtl_move yes，no确定绘图模式中的“移动”和“移动附属”命令是(yes）否（no) 一起执行allow_move_view_with_move yes，no设置为“yes"时，可以使用“绘图”模式中的“移动”命令，移动绘图视图.allow_old_style_round yes, no确定系统使用哪一个倒圆角创建功能。
Proe Config全部配置文件说明10-04
iges_out_ent_as_bspline true, false (Pro/INTERFACE)控制系统如何将绘图输出到IGES文件。
true - 将除了线和弧之外的所有几何像素以三次B-样条输出。
false - 不以三次B-样条输出像素。
iges_out_jamais_compliant yes, no（组件、绘图和零件）yes - 指定满足专用JAMA-IS子集规范的IGES输出，符合JAMA-IS (Japan Automobile ManufacturersAssociation IGES Subset Specification)（日本汽车制造者协会IGES子集规范）版本1.02。
no - 指定不用专用JAMA-IS子集规范标准IGES输出。
iges_out_mil_d_28000 yes, noyes - 指定使用MIL-D-28000像素子集的IGES输出。
iges_out_spl_crvs_as_126 yes, no创建一个IGES文件时，将所有零件几何样条曲线变为IGES像素126（B-样条）。
iges_out_spl_srfs_as_128 yes, no创建一个IGES文件时，将所有零件几何样条曲面转换为IGES像素128（B-样条）。
iges_out_start_note yes, noyes - 将「system_iges_header_file」和「user_iges_header_file」指定的文本作为一条注释输出到绘图上。
要控制注释的放置，用配置文件选项「put_iges_drawing_entity」：yes - 将注释放在右下角（标题块区域）。
no - 将注释放在左下角。
iges_out_symbol_entity yes, no以IGES通用符号像素、IGES类型号228，或组件像素输出绘图符号：注释和线条。
iges_out_trim_curve_deviation 数值（缺省值= 当前精度）设置一条XYZ裁剪曲线（边界）和一条裁剪曲面的底层曲面间的距离最大值。
PROE 配置文件的设置
一、config 的设置常用配置文件：config.pro ——系统配置文件，配置整个PROE系统gb.dtl ——工程图配置文件，你可以先简单的理解为设置箭头大小，文字等标注样式。
format.dtl ——工程图格式文件（可以简单的理解为图框）的配置文件。
table.pnt ——打印配置文件，主要设置工程图打印时的线条粗细、颜色等。
A4.pcf ——打印机类型配置文件，主要设置工程图打印出图时的比例、纸张大小等。
config.win.1 ——（1为流水号，每改一次自动增加）操作界面、窗口配置文件，比如说我们可以在这个文件中设置模型树窗口的大小，各种图标、工具栏、快捷键在窗口的位置等等。
Tree.cfg ——模型树配置文件，主要设置在模型树窗口显示的内容、项目。
Config 文件，从后缀分主要有config.pro和config.sup两种，可满足包括系统的精度、显示设置、单位、打印机的设置、快捷键的设置、输入输出设置等等。
应由经验丰富的工程师针对公司需要进行设置，然后作为公司的标准执行，方法是：在config 加入一行：变量名：drawing setup file值：指向你的dtl文件的绝对路径如：F:\MY Design\Pro_Stds\Config\Company.dtl 然后将config保存为config.pro在你的工作目录（安装proe时指定的目录，不是安装目录）下，启动proe会自动加载了。
这样利于数据的交换和统一管理。
config.pro 还要放在恰当的位置才能正确调用！Config.pro可以放在text目录下面顺利加载。
建议把config.pro放在启动目录下，不要放在PROE安装目录的text目录下面，以免造成管理混一、config的设置常用配置文件：config.pro——系统配置文件，配置整个PROE系统gb.dtl——工程图配置文件，你可以先简单的理解为设置箭头大小，文字等标注样式。
PROE-Config
如果未在这些配置文件中设置选项，那么系统将使用该选项的缺省值。
在
应在启动Pro/ENGINEER进程之前，设置配置文件中的选项。
全局考虑
切记配置文件选项将全局性影响模型，也就是它们影响Pro/ENGINEER的所有模式，而且它们影响每个相关的绘图。要控制单个绘图的外观，可修改绘图设置文件。
使用绘图设置文件
定义视图的布局
设置视图显示
放置注释
定义表格
创建捕捉线
显示尺寸
图1使用绘图模板创建绘图
系统提供了多个缺省模板。也可创建定制的绘图模板。这些绘图模板将主要由系统管理员创建和维护。在以后的章节中将讨论绘图模板的创建。这些模板创建后，即可应用到绘图创建中。
使用配置文件
使用Pro/ENGINEER配置文件，可通过指定环境选项和其它全局设置的初始值，来定制工作环境。例如，可开或关铃声，可选取合适的背景色或将模型显示设置为隐藏线模式。
-创建从视图偏移预定距离的捕捉线
-以FRONT、RIGHT、TOP视图位置优先顺序显示模型尺寸
根目录中的Config.pro-此文件在根目录中。如果系统在此文件中遇到与装载点文件config.p。
当前目录中的Config.pro-此文件位于Pro/ENGINEER的启动目录中。如果系统在这个文件里遇到与装载点目录或根目录中的config.pro相同的选项，那么系统使用此选项，而覆盖其它选项。
为新文本指定缺省粗度。
text_width_factor
0.80000
0.235<值<8
指定文本宽度和文本高度之间的缺省比例。系统将保持这个比例，除非使用文本宽度(TextWidth)选项改变宽度。
课堂练习
目标
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
! ☆☆☆郑州豪威尔电子科技有限公司标准配置☆☆☆! 版本：proe2.0M080! 编制：刘战胜! 日期：2008年5月6日!※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※※accuracy_lower_bound 0.0001!环境输入一个精确值来覆盖缺省下限。
上限固定为0.01。
相对精度的最小值是1E-06。
acis_out_version 5!数据交换允许用户选择ACIS 输出版本。
4, 5activate_sketch_with_dflt no!特征yes-使用系统缺省设置自动激活草绘器。
add_lower_level_comps_to_layer no!层设置此选项为"yes"将取消选中"当前偏好层"选项，此选项允许将低级元件添加到顶级层中。
add_weld_mp no!焊接Yes -计算质量属性时，包括焊缝；No - 计算质量属性时，排除焊缝。
advanced_intersection no!组件控制相交工具的外观和可用功能的范围。
yes, noaf_copy_references_flag no!用户界面在注释特征定义对话框中切换复制参照列的显示no, yes noalign_cable_bundles yes!机电在新创建的束相交或分支位置处将其对齐yes, noallow_anatomic_features no!特征允许创建Pro/E 2000i 之前版本的几何特征，包括耳、环形槽、刀刃、槽、凸缘、轴、局部推拉、半径圆和截面圆等特征。
allow_confirm_window yes!用户界面退出Pro/ENGINEER 时显示一个确认窗口。
这就允许使用鼠标来确认/取消退出Pro/ENGINEER。
yes, noallow_float_opt_checkout no!系统yes-对于浮动模块允许失败检查。
allow_move_attach_in_dtl_move yes!绘图yes-绘图模式中的"移动"和"移动连接"命令一起动作。
!no-绘图模式中的"移动"和"移动连接"命令不一起动作。
allow_move_view_with_move no!绘图-允许通过拖动在页面上动态移动绘图视图。
yes, noallow_package_children all!组件设置子项包装元件可以具有的类型。
!all-特征和元件可作为包装元件的子项。
!feat-仅特征可作为包装元件的子项。
!none-包装元件不能有子项。
allow_ply_cross_section yes!杂项yes-允许Pro/COMPOSITE 创建复合摺的横截面。
allow_redo_intersections no!组件yes-在组件特征菜单中显示重新求交命令。
allow_ref_scope_change yes!参照控制no-当改变"参照范围"用户界面时，显示信息"配置文件设置禁止改变参照范围"。
allow_refs_to_geom_reps_in_drws no!绘图yes-允许创建绘图参照几何表示(包括尺寸、注释和导引)。
如果参照几何的改变导致绘图中不更新几何表示，则这些参照可allow_rfs_default_gtols_always no!尺寸和公差yes-即使ANSI 标准不允许，也可以创建RFS/缺省的几何公差。
allow_save_as_instance no!组件yes-允许此选项将把活动模型的副本保存为族表实例。
allow_shrink_dim_before no!铸造和模具设计允许关系之前有计算。
yes, noallow_udf_style_cosm_threads no!特征定义修饰螺纹界面。
yes-将修饰螺纹创建为UDF。
no-将修饰螺纹创建为修饰螺纹特征。
allow_workpiece_silhouette no!确定工件是否可用于创建侧面影像加工窗口。
!no-仅允许使用参照零件;!yes-允许使用工件和参照零件;!auto -仅允许使用工件。
ang_dim_in_screen no!尺寸和公差!yes-如果是在缺省的平移/缩放设置(视图>平移/缩放>重置) 下显示，系统就检测屏幕上的角度尺寸是否可见。
!如果不可见，系统就将该尺寸移动到一个可见位置。
ang_units ang_deg!环境!将角度尺寸的显示设置为小数度(ang_deg)、度和小数分(ang_min) 或度、分和小数秒(ang_sec)。
angle_grid_interval 1!特征-以角度单位修改栅格间隔以用于句柄移动。
angular_tol 0!尺寸和公差-设置缺省角度公差尺寸的另一种格式。
该值设置小数位数，公差是实际公差值。
对于整数尺寸，该值为零，公差是一angular_tol_0.0 5angular_tol_0.00 50angular_tol_0.000 500angular_tol_0.0000 5000angular_tol_0.00000 50000angular_tol_0.000000 500000!尺寸和公差-为角度尺寸设置缺省公差。
每个选项为特定的小数位置设置一个公差。
该值是最后一位小数的位数。
arc_radius_limit 1!在NCL 文件的CIRCLE 语句中设置半径的上限。
该值必须为正值。
否则，将使用10*零件尺寸。
ask_designate_owners yes!显示要指定的必需的和可选的所有者。
yes, noassy_mfg_open_mode feature!制造yes-所有组件NC模型都将在Standard NC中打开。
mfg, process, featureatb_auto_check_on_activate off!数据交换设置ATB '激活时自动检查状态'切换的状态。
on, offatb_auto_check_on_retrieve on!数据交换设置ATB '检索时自动检查状态'切换的状态。
on, offatb_auto_check_on_update off!数据交换设置ATB '更新时自动检查状态'切换的状态。
on, offatb_ident_cadds_files no!数据交换允许开启文件的浏览器中标识CADDS 文件。
yes, noatb_prod_asm_upd_by_comp_ids yes!数据交换yes-允许基于组件元件标识更新Pro/DESKTOP 组件。
no-更新将基于元件名称。
atb_show_log on!数据交换设置ATB '显示日志'切换的状态。
on, offattach_menumanager no!设置主Pro/E 窗口的菜单管理器附件。
yes, noauto_assembly_with_layouts yes!组件yes-启用自动装配。
no-禁用自动装配。
auto_associate_dimensions no!数据交换yes-绘图设置选项associative_dimensioning 也设置为"是"。
系统试图将输入的IGES 尺寸(还未关联的)和相应的输入auto_constr_always_use_offset no!组件控制自动约束是否应创建偏距。
yes -自动约束始终创建偏距。
no-如果曲面在公差内自动约束将捕捉对齐或配对。
never-自auto_constr_offset_tolerance 0.5!绘图设置创建偏距尺寸的自动约束公差。
如果距离小于此公差与元件尺寸的乘积，偏距将设置为重合。
缺省值为0.5。
auto_convert_cables yes!机电yes-当再生一个版本11.0 以前的缆组件时，系统自动为该组件中的每根单独线或缆创建一个单独的线轴特征。
no-出现一个auto_regen_views yes!绘图Yes -当从一个窗口改变至另一个窗口时，自动重画绘图显示。
no-只会有在通过“重画”或“视图> 更新”时才会更新绘图视图auto_traceback yes!系统若设置为"yes"，则在出现严重错误时将生成traceback.log 文件。
auto_xml_on_retrieve no!机电检索电缆组件时，自动从XML 文件载入电缆逻辑参照yes, noauto_xml_on_save no!机电保存电缆组件时，自动创建XML 逻辑参照yes, noautobuildz_enabled no!绘图加载AutobuildZ 应用程序。
yes, noautoplace_single_comp yes!组件yes-装配带有界面的元件时会自动将该元件放置在满足界面定义的第一个位置处。
auxapp_popup_menu_info no!用户界面在跟踪文件中启用弹出式菜单信息的显示。
yes, nobell no!环境yes-打开每次提示后都要响的键盘铃。
no-关闭键盘铃。
要覆盖该设置，使用"工具"菜单中的"环境"对话框。
bitmap_size 200!数据管理与save_bitmap 一起工作。
确定已保存的位图图像的尺寸(正方)。
blank_layer 0!层开始Pro/ENGINEER 进程时，遮蔽指定的层。
其值为层标识。
blended_transparency yes!模型显示yes -将出现透明颜色，并在着色模型时使用alpha 混合(如果支持的话)。
bm_graph_tool default!用户界面BMX 图形工具public default, public excel_linked, public excel_embedded, internal generic_graphtoolbmx_param_restrictions yesbump_revnum_on_retr_regen yes!组件确定在组件检索期间再生和更改的普通模型的版本号是否增加。
!仅当new_asm_regen_revnums 为"是" 时才适用(否则，将不会有版本号的变化)。
button_name_in_help no!用户界面是-在该按钮相关联的帮助文本中，以英文形式显示所有选定的菜单选项的名称和菜单。
yes, nocable_int_portions_for_clr no!机电no-排除对内部缆段的全局间隙检测。