卸船机中英文对照表

常用船舶口令机器英汉对照

微速后退
Dead slow astern.
微速后退
Dead slow astern!
后退一
Slow astern.
车微退
Engine dead slow ahead
后退一
Slow astern.
车退一
Engine slow astern.
后退二
Half astern.
后退二
Half astern.
车退二
抛(左、右)锚
Let go(port, starboard)anchor.
刹住
Hold on.
刹住
Hold on.
停止绞锚
Stop heaving (Avast heaving).
停止绞锚
Stop heaving(Avast heaving).
锚链方向
How is chain leading?
锚链垂直Up and down.
engines ahead.
两(双)退…
…astern two (or both)
englnes.
两(双)退……
…astern two(or both)
englnes.
两(双)车退…
Two(or both)
englnes astern.
左(右)退…
…astern port(starboard)
engine.
口令
Order
复诵
Reply
报告
Report
双车
双
车
左(右)进一
Slow ahead port (starboard).
左(右)进土
Slow ahead port (starboard).

船舶轮机英语单词总结

船舶轮机英语单词总结船舶轮机英语单词总结A layer of lubricant 润滑层abrasive 有磨蚀的accommodation 住舱accommodation ladder 舷梯accommodation 居住舱室Accomplish 完成，达到，实现activate 使活动，起动Adjustment 调整Administrative offices 管理办公室adopt 采用advantage 优势，优点，效益应用affect 影响Aforesaid 上述的，前述的（常用于法律文件）aft ballast tank 艉压载舱Aggregate 合计，总计air cushion craft 气垫船air draught 水面上高度air pipes，sounding pipes and overflow pipes 空气管、测量管和溢流管路alarm 警报器alkalinity 碱度，碱性all duties pump 总用泵alloy 合金alternative 替换物，选择对象alternator 交流发电机aluminum 铝Aluminum 铝among 在……之中Analyze 分析anchor 锚anchor arrangement 锚泊设备anchor bell 锚钟anchor hoisting winch 起锚绞车anchor light 锚灯Anchorage 锚地Anchor-heaving trial 抛锚试验anti-corrosive oil 防腐油Aperture 孔，穴Applicant 申请者Applicant 申请者application 应用application 应用，运用Approach 方法，步骤，途径Appurtenance 辅助的设备，附属设备，配件Aptitude （特殊）才能，适应性Arbitration 仲裁around 在……周围，绕过arrangement 布置，安排，装置，方案aspect 方面Assembly line 装配（流水）线Assembly 装配assembly 组件，组装Assign 分配，指派assigning 确定，指派assist 帮助，协助atmospheric 大气的atomization 雾化attach 缚，系，附，归属attached pump （主机）附带泵attractive 吸引人的，引起注意的audible 听得见的automobile n. 汽车auxiliary engine 发动机auxiliary pump 辅助泵axial flow pump轴流泵axial flow 轴流式axial plunger pump轴流柱塞泵axial 沿轴的，轴的axis 轴balance 平衡Balance 平衡ballast （船等）压载物ballast pump 压载泵ballast tank 压载舱barge 驳船barge-carrier 载驳货船be adjacent to 靠近，接近be attached to 附属于Be built to order 按定单建造，按定货单制作be confined to 被限于……be divided into 分成be made up of…由……构成bearing 轴承bedplate 基座bell 钟，罩Bench work 钳工Bid 投标bilge piping and ballast piping 舱底水与压载管系bilge piping system of cargo pump rooms and cofferdams 货泵舱和隔离空舱舱底水系统bilge pump 舱底水泵bilge 舭bilge 舱底（水）bilge 舱底，船舱积水Bind 约束blade 叶片，桨叶blank 隔开、封着，使无效Blast 喷丸（除锈）blind-flange 盲板法兰Block 墩木，块，阻塞block 块boat deck 艇甲板Body plan 横剖型线图，正面线图body 主体boiler feed and blow off pipes 锅炉给水和泄放管boiler fuel oil system 锅炉燃油系统Bollard test，dock trial 系泊试验bolt 螺栓，用螺栓固定boom length 吊杆长度boom 吊杆Boom 吊杆boost(er) pump 增压泵bottom dead centre (BDC ) 下止点bow 船首bower anchor 首锚Bracket 支架，托架brake horsepower 制动马力，制动功率brake 制动器，刹车branch 分支，支管brazing 铜焊（接）Bridge crane 行车，桥式起重机bridge deck 驾驶甲板Bridge 桥楼brittle 易碎的，脆弱的bronze 青铜（铜与锡合金）Brozen sleeve 青铜筒套buffer tank 缓冲柜buffer 缓冲器，贮存装置Building basin 船台Building period 建造周期built-in 内装的，机内的，固定的bulk-carrier 散货船bulkhead 舱壁bulkhead pieces 舱壁部分bulkhead 舱壁bulkhead 隔壁，防水壁bulwarks 舷墙Burner 气焊工bursting pressure 爆炸压力by comparison 通过比较cabin deck 起居甲板cable releaser 弃链器cablelifter 锚链轮Calorific 卡的，热量的，发热的calorific 热（量）的，发热的cam clearance 凸轮间隙Camber 拱形cap 盖capstan 绞盘，绞车captain deck 船长甲板carbonaceous 碳的Cargo capacity 载货量，货舱容量，舱容cargo handing gear 起货设备cargo handing productivity 装卸能力cargo oil piping system 货油管系cargo oil suction 吸油口cargo space 货物舱位cargo winch 起货绞车Carpenter 木匠carrier ring 承磨环casing 箱，外壳cast steel chain 铸钢锚链casualty 灾祸，意外catalytic 催化的catamaran 双体船category 类别cause 原因，引起central cooling system 中央冷却系统centralized control 集中控制centrifugal oil separator room 分油机室centrifugal 离心的centrifuge 离心（分油、净油）机centrifuge 离心分离机cetane 十六烷值chain cable compressor ,chain stopper 止链器chain cable 锚链chain link 锚链环chain locker 锚链舱chain pipe 锚链管chain winch 锚链绞车Charge 费用charge 装，充chemical carrier 化学品（运输船）Chipper 风铲工，缺陷修理工chock 塞块，楔型垫chromium 铬circuit 回路，管路，电路circulating lubricating oil tank 滑油循环舱circulating pump 循环泵circulating tank 循环柜Class notation 船级符号Class symbol 入级符号class 等级cleanse 清洗clutch 离合器clutch 离合器cock 开关，龙头Coefficient 系数cofferdam 隔离空舱Collapse 毁坏collecting tank 收集柜Collision 碰撞Combat system 作战系统combustion 燃烧，焚毁，发（点）火commercially 商业上Compact 紧凑的compare 比较，对比Compartment stuffing box 隔舱填料函compartment 隔间，隔室Compass adjuster 罗经校正员compass deck 罗经甲板Compel 强迫compensate 补偿Competitive 竞争的Completion 完成Complex 复杂的，合成的，综合的complexity 复杂，复杂性component 元件，组成元件compound-supercharged diesel engine 复合式增压柴油机compressed air piping system 压缩空气系统compression （发动机，如内燃机中工作液体的）压缩compression pump 压缩泵Compromise 折衷，调和Compulsory 强迫的，强制的，义务的Concrete 混凝土condensate and exhaust steam piping 凝水和乏汽管系Configuration 构造，结构，配置，外形considerable 相当的，大量的constitute 构成construction 结构Consult 咨询Consumable 消耗性的Consumable 消耗物品consumption 消耗，消费contact 接触container 集装箱container ship 集装箱船container ship 集装箱船container 集装箱，容器，壳，罩containerization 货柜运输contamination 污染（物）conventional 常规的，惯例的convey 传递coolant 冷却剂copper n. 铜copper 铜corrosion 腐蚀，锈corrosive 腐蚀（性）的corrosive 腐蚀的，腐蚀性的counteract 克服coupling 联接，联接器，联轴节Course keeping test 航向稳定性试验Craft 船，手工艺Crane operator 起重工crane 克令吊，起货机crane 起重机crankpin 曲柄销Criteria 准则，标准，规范cross 十字的，交叉的crow’s nest 桅上瞭望台crown 冠，顶部，活塞crows nest 瞭望台crude oil 原油cruiser 游船Culminate （与in连用）达到。

船舶设备部件中英文对照

一、船体设备1. 锚Anchor2. 舵叶Rudder blade3. 舵柄Rudder tiller4. 舵挂臂Rudder horn5. 舵销/舵轴Rudder pintle or axle6. 舵承Rudder carrier7. 舵杆Rudder stock8. 主舵机Main steering gear9. 固定式灭火系统Fixed fire extinguishing system10. 惰气系统Inert Gas System11. 惰性气体发生器inert gas generator12. 洗涤塔 scrubber13. 甲板水封deck water seal14. 鼓风机Blower15. 压力真空阀P/V valves16. 舷梯Accommodation Ladders17. 风雨密舱口盖Weather tight hatch covers18. 救生/救助艇Lifeboat/rescue boat19. 救生/救助艇架Life boat/rescue davit20. 海上撤离系统Marine evacuation system21. 起重机(安全工作负荷≥1t)Deck cranes22. 吊杆装置(安全工作负荷≥1t)Derrick rig二、轮机设备1. 柴油机(功率≥130kw)Diesel Engine2. 应急鼓风机Emergency Blower3. 燃气轮机Turbines4. 柴油机地脚螺栓Foundation bolts & nuts5. 推力轴Thrust Shaft6. 齿轮箱Reduction Gear7. 离合器Clutch8. 中间轴Intermediate Shaft9. 连接螺栓Coupling bolts10. 联轴节Shaft coupling11. 艉轴管Stern Tube12. 艉轴Stern Shaft13. 螺旋桨轴Screw Shaft14. 备用轴Spare Shaft15. 艉轴密封装置Stern shaft seal16. 螺旋桨Propeller17. 备用螺旋桨Spare Propeller18. 导流罩Kort nozzle19. 可调桨装置CPP Installation20. “Z”型推进器装置Z-Type Propulsion System21. 喷水推进器装置Water-jet propulsion system22. 动力定位/侧推装置Dynamic positioning/lateral thruster23. 蒸汽/热油系统STEAM/THERMAL OIL SYSTEM24. 主锅炉Main Boiler25. 辅锅炉Aux. Boiler26. 废气锅炉Exhaust Gas Boiler27. 组合锅炉Composite Boiler28. 热油锅炉Thermal Oil Heater29. 蒸汽透平Steam Turbines30. 燃烧器Burning Unit31. 弦外排污阀Overboard discharge Valve32. 压缩空气系统COMPRESSED AIR SYSTEM33. 主空压机Main Air Compressor34. 辅空压机Aux. Air Compressor35. 应急空压机Emergency Air Compressor三、电气设备1. 发电机组(≥50kV A)Electric generator set2. 发电机(≥50kV A)Electric generator3. 应急发电机组Emergency generator set4. 应急配电板Emergency switchboard5. 主配电板Main switchboard6. 轮机自动化系统（控制、监测、报警）Automation of the machinery(Control, Monitoring, Alarm)7. 机舱集中控制台Engine room centralized control panel8. 驾驶集中控制台Bridge centralized control panel9. 分配电箱Electrical distribution box10. 锚机Anchor windlass11. 主机遥控系统M.E. remote control system12. 自动化机舱安全和报警系统Safety system for automation of the machinery13. 自动化机舱安全和报警系统Alarm system for automation of the machinery14. 车钟Telegraph15. 水渗漏检测报警系统和传感器Water leakage detection system and sensor16. 液位监测系统Level gauging system(and sensors)17. 电力推进电机和控制装置Electric propulsion motor and control apparatus18. 货舱进水报警系统Cargo hold flooding alarm system19. 组合声光报警灯板（箱）Audible and visual group alarm panel20. 岸电箱Connecting box for Land-use power21. 电罗经Gyro compass22. 电罗经复示器Gyro repeaters23. 雷达Radar24. 自动雷达标绘仪Automatic radar plotting aid(ARPA)25. 船令广播系统Public address system26. 自动识别系统Automatic identification system(AIS)27. 航行数据记录仪V oyage data recorder(VDR)28. 综合驾驶台系统Integrated bridge system（IBS）29. 综合航行系统Integrated navigation system（INS）30. 国际海事卫星船舶地面站Ship earth station(SES)31. 通用紧急报警系统General alarm systembrake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定 capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器 chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮 cross-sectional area 横剖面面积crow’s nest 桅杆了望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修。

船舶轮机英语集成原版

船舶英语目录一.职位及工种(Titles and type of work) ····· 1 二、柴油机类(Words about diesel engine) ····· 3 三、船舶机械类(Words about marine machinery) ·· 11 四、阀门(Words about valve) ···· 14 五、泵类(Words about pump) ·········· 16 六、甲板机械类（Deck machinery ）······ 18 七、工具类(Word about tools) ········ 20 八、常用物料(Material in common use) 26 九、常用紧固件(Part of fixation in common use) ··· 28 十、常用油类(Oil in common use) ·····28 十一、常用量词(Quantifier in common use) ·········29 十二、国家名称(Name of country) 。

30 十三、常用缩语(abbreviation in common use) ·····31 十四、船用动态常用单词(marine tends word) 32 十五、船舶机电设备操作词汇(manipulate of marine equipment) ·33 十六、故障常用单词(words about malfunction) ····· 35 十七、保养检修常用词汇(Words about maintain and examination) 38 十八、常用数字(Numeral in common use) 40 十九、时间、季节与方向(Time 、Season and Direction) ·····42 二十常用词组（Phrases in common use ）·45 二十一、常用动词和例句(Verb in common use and example) ····48 二十二、问候和常用表达语(Greeting and common expression) ····67 二十三、主机提交过程用语(Delivery expressions for main engine) 68 二十四、空压机和空气系统用语(Air compressor and Air system) ···· 75 二十五、锅炉提交用语(Delivery expressions for boiler) ···77 二十六、锚绞车提交过程用语(Delivery expressions for anchor windlass) 79 二十七、舵机提交过程用语(Steering gear delivering) ··· 87 二十八、付机提交过程用语（Delivery expression for A/E ）····· 91 二十九、救生艇提交过程用语(Delivery expressions for lifeboat) ··92 三十、其他提交项目 (Delivery expressions for other items) ···95 三十一、甲板机械系泊试验 (Mooring test for deck machinery) ········96 三十二、机舱设备系泊试验 (Mooring test for the equipment in E/R) ···98 三十三、谈论故障常用语（Expressions for trouble ）············100 三十四、谈论检修常用语(Expressions for overhaul) ············101 三十五、谈论试验和检验(Talking about test & check) ···········103 三十六、谈论技术要求(Talking about technology required) (105)一．职位及工种(Titles and type of work) 1．船长 Captain2．大副 Chief officer3．二副 Second officer 4．三副 Third officer 5．四副 Fourth officer 6．水手长 Boatswain7．水手 Sailor & Seaman 8．木匠 Carpenter9．轮机长 Chief engineer 10．大管轮 Second engineer 11．二管轮 Third engineer 12．三管轮 Fourth engineer 13．机匠长 Chief motorman 15．机匠 Fitter 16．加油工 Oil man17．大电 Chief electrician 18．电工 Electrician19．车间主任 Workshop director 20．工长 Section chief 21．班长 Fore man 22．钳工 Fitter23．主管工程师 Engineer in charge 24．机务&船东 Superintendent &Super &Owner 25．助理工程师 Assistant engineer 26．验船师（机）Register 27．验船师（船）Surveyor 28．油漆工 Painter 29．焊工 Welder 30．大橱 Chief cook 31．物料员 Store keeper 32．加油工 Oiler33．机工 Mechanic 34．甲板员 Deck man 35．电线工 Wireman 36．外包工 Laborer 37．铸工 Molder38．管子工 Pipe fitter 39．起重工 Crane operator二、柴油机类(Words about diesel engine) 1．主机 Main engine2．二冲程柴油机 Two-stroke diesel engine 3．四冲程柴油机 Four-stroke diesel engine 4．高速柴油机 High speed diesel engine 5．中速柴油机 Middle speed diesel engine 6．低速柴油机 Low speed diesel engine 7．气缸盖(缸头) Cylinder head 8．安全阀 Safety valve 9．释放阀 Relief valve 10．示功阀 Indicator valve 11．示功考克 Indicator cock 12．空气起动阀 Air starting valve13．起动空气分配器 Air starting distributor 14．油头(燃油喷射器) Fuel injector 15．排气阀 Exhaust valve 16．气缸套 Cylinder liner17．冷却水套 Cooling water jacket 18．气缸注油器 Cylinder lubricator 19．活塞 Piston20．活塞头 Piston crown 21．活塞裙 Piston skirt 22．活塞销 Piston gudgeon pin 24．活塞杆 Piston rod 25．活塞环 Piston ring26．活塞环槽 Piston ring groove 27．压缩环 (气环) Compression ring 28．刮油环 (油环) Oil scraper ring 29．减磨令 Wear ring (copper ring) 30．伸缩管(水拉管) Telescopic pipe 31．活塞冷却空间 Piston cooling space 32．填料箱(函) Stuffing box 33．填料箱密封环Sealing ring for Stuffing box 34．填料箱压缩环 Pressure ring for Stuffing box 35．填料箱刮油环Scraper ring for Stuffing box 36．扫气箱 Scavenging receiver 37．扫气口 Scavenging port 38．排气口 Exhaust port 39．十字头 Cross head 40．十字头销 Crosshead pin 41．十字头轴承 Crosshead bearing 42．十字头滑块 Crosshead slipper 43．滑块 Guide shoe44．十字头导板45．连杆46．连杆大端轴承47．连杆小端轴承48．曲柄轴承49．曲柄销 Crank pin 50．曲轴 Crank shaft 51．曲轴颈 Crank journal 52．曲柄臂 Crank web53．拐档差 Crank deflection 54．主轴承 Main bearing 55．主轴颈 Main journal 56．轴承瓦 Bearing bush57．上轴瓦 Upper bearing bush 58．上轴瓦 Upper half59．下轴瓦 Lower bearing bush 60．下轴瓦 Lower half 61．推力轴承 Thrust bearing 62．推力块 Thrust pad 63．推力盘 Thrust disc 64．推力轴 Thrust shaft 65．底座 Bed plate 66．机架 Frame67．曲柄箱 Crank case68．曲柄箱导门 Crank case door 69．曲柄箱防爆门 Explosion-proof Crank case. 70．定时齿轮 Timing gear 71．飞轮 Flying wheel 72．凸轮 Cam73．凸轮轴 Cam shaft74．喷油凸轮 Fuel injection cam 75．链条 Chain76．链条轮 Chain wheel 77．链条箱 Chain box 78．推杆 Push rod 79．摇臂 Rocker arm 80．排气阀 Exhaust valve 81．吸气阀 Suction valve 82．排气总管 Exhaust manifold 83．进气总管 Air inlet manifold84．高压燃油管 High pressure fuel pipe 85．活塞冷却水管 Piston cooling water pipe 86．法兰 Flange87．贯穿螺栓 Tie bolt (tie rod) 88．端盖 Side cover89．滑油泵 Lubricating oil pump 90．燃油泵 Fuel oil pump 91．滑油泵齿轮 Gear for lubricating oil pump 92．燃油泵齿轮 Gear for fuel oil pump 93．叶轮 Impeller 94．柱塞 Plunger 95．导杆 Guide rod 96．导套 Sleeve97．滚动轴承 Ball bearing 98．滑动轴承 Sliding bearing99．推力滚动轴承Thrust ball bearing 100．推力面 Thrust surface (thrust side) 101．盘车机 Turning gear 102．增压器 Turbocharger 103．涡轮机(透平) Turbine104．涡轮 Turbine wheel 105．涡轮叶片 Turbine blade 106．喷嘴 Nozzle 107．废气叶轮 Exhaust impeller 108．废气叶轮片 Exhaust blade 109．废气端 Exhaust side 110．透平端 Turbine side 111．转子轴 Rotor shaft 112．油泵 L.O.pump 113．换向装置 Reversing device 114．换向伺服期 Reversing servomotor 115．压气机(鼓风机) Blower 116．膨胀接 Expansion joint 117．调速器 governor 118．飞重 Flying weight 119．补偿阀 Compensate valve 120．针阀 Needle valve 121．开口销 Cotter pin 122．轴封 Shaft seal 123．机械密封 Machinery seal 124．配电盘 Switchboard 125．应急配电盘 Emergency switchboard 126．应急发电机 Emergency generator 127．滤器 Filter 128．细滤器 Filter 129．粗滤器 Strainer 130．滑油滤器 L.O. filter 131．燃油滤器 F.O. filter 132．空气消音器 Air intake silencer 132．空气滤器 Air intake filter 133．空气瓶 Air bottle (receiver) 134．分油机 Separator 135．油水分离器 Water-oil separator 136．净油机 Purifier 137．燃油净化器 F.O. purifier 138．二氧化碳 CO2 139．二氧化碳瓶 CO2 bottle 140．正时齿轮 Timing gear 141．导向棒装置 Guide bar 142．注油器驱动 Lubricator driver 143．链条张紧装置 Chain tightener 144．凸轮轴传动轮 Chain wheel on cam shaft 145．中间链链传动轮Intermediate chain wheel 146．注油器驱动装置Lubricator drive 147．链条张紧装置 Chain tightener 148．滚筒导座 Roller guide housing 149．应急操纵台 Emergency console 150．力矩平衡器 Moment compensator 151．主启动阀 Main starting valve 152．启动空气分配器Starting air distributor 153．喷油器 Fuel valve 154．扫气系统 Scavenge air system 155．安全帽 Safety cap 156．机座 Bed plate 157．轴向振动减振器 Axial vibration damper 158．贯穿螺栓 Arrangement of stay bolt 159．示功器驱动装置 Indicator driver 160．端罩 End shields 161．气缸架 Cylinder frame 162．气阀传动装置 Valve operating device 163．摇臂润滑油泵 Rocker arm lubricating oil pump 164．摇臂润滑油柜 Rocker arm lubricating tank 165．摇臂润滑滤器Rocker arm lubricating filter 三、船舶机械类(Words about marine machinery) 1．船用锅炉 Marine boiler 2．废气锅炉 Exhaust boiler 3．辅锅炉 Donkey boiler 4．组合式锅炉 Combined boiler 5．火管 Fire tube 6．给水管 Feed pipe 7．炉膛 Furnace 8．炉墙 Furnace wall 9．火侧 Fire side 10．水侧 Water side 11．燃烧器 Oil burner 12．安全阀 Safety valve 13．上排污 Upper drain 14．下排污 Lower drain 15．锅炉皮阀 Mounting valve 16．水位计 Water level gauge 17．压力表 Pressure gauge 18．主汽门 Main steam valve 19．玻璃管 Glass tube 20．空调装置 Air-conditioning plant 21．制冷装置 Refrigerating plant 22．冰机 Fridge. Machine 23．空气压缩机 Air compressor 24．造水机 Fresh water generator 25．板式冷却器 Plate type cooler 26．机舱天车 Engine room crane 27．天车导轨 Crane rail 28．电磁阀 Solenoid valve 29．舵机 Steering gear 30．舵承 Rudder bearing carrier 31．液压缸 Hydraulic cylinder 32．废气涡轮增压器Exhaust gas turbocharger 33．弹簧阀 Spring loaded valve 34．冷凝器 Condenser 35．分油器 Oil separator 36．轴带发电机 Shaft generator 37．焚烧炉 Oil burner 38．分油机 Separator 39．分离筒 Separator bowl 40．配水盘装置 Paring disc device 41．转数计 Revolution counter 42．控制阀 Control valve 43．辅机 Auxiliary machinery 44．制冷装置 Refrigerating plant 45．海水淡化装置Sea water desalting plant 46．热交换器 Heat exchanger 47．船用气瓶 Marine air bottle 48．冷风机 Cooler unit 49．防水风门 Fire damper 50．气密挡板 Gas tight damper 51．排气风机 Exhaust fan 52．舱室通风机 Cabin fan 53．机舱通风机 Engine room fan 54．应急鼓风机 Emergency blower 四、阀门(Words about valve) 1．吸气阀 Suction valve 2．排气阀 Exhaust valve 3．控制阀 Control valve 4．导阀 Pilot valve 5．单向阀 Non-return valve 6．口琴阀 Flap valve 7．调节阀 Regulating valve 8．液压阀 Hydraulic valve 9．膨胀阀 Expansion valve 10．给水阀 Feed valve 11．排水阀 Discharge valve 12．截止阀 Stop valve 13．吹泄阀 Blow-off valve 14．空气阀 Air valve 15．泄放阀 Drain valve 16．止回阀 Check valve 17．海底阀 Sea valve 18．回流阀 Retune valve 19．节流阀 Throttle valve 20．进气阀 Inlet valve 21．出气阀 Outlet valve 22．热力阀 Thermal valve 23．中央阀 Center valve 24．单向阀 One way valve 25．二通阀 Two way valve 26．三通阀 Triple valve 27．旁通阀 By-pass valve 28．换向阀 Change-over valve 29．减压阀 Pressure-reducing valve 30．溢流阀 Overflow valve 31．自闭阀 Self-locking valve 32．针阀 Needle valve 33．平衡阀 Balance valve 34．循环阀 Circulation valve 35．主阀 Main valve 36．滑阀 Slide valve 37．蝶阀 Butter-fly valve 38．截止阀 Shut-off valve 39．闸板阀 Gate valve 40．通海阀 Sea suction valve 41．吹除阀 Sea chest cleaning valve 42．防浪阀 Storm valve 43．舱壁阀 Bulkhead valve 44．快关阀 Emergency shut off valve 45．呼吸阀 Breather valve 五、泵类(Words about pump) 1．电动泵 Motor-driven pump 2．柱塞泵 Plunger pump 3．叶片泵 Vane pump 4．回转泵 Rotary pump 5．齿轮泵 Gear pump 6．往复泵 Reciprocating pump 7．离心泵 Centrifugal pump 1．电动泵 Motor-driven pump 2．柱塞泵 Plunger pump 3．叶片泵 Vane pump 4．回转泵 Rotary pump 5．齿轮泵 Gear pump 6．往复泵 Reciprocating pump 7．离心泵 Centrifugal pump 8．真空泵 Vacuum pump 9．螺杆泵 Screw pump 10．喷射泵 Ejector pump 11．冷却泵 Cooling pump 12．淡水泵 Fresh water pump 13．海水泵 Sea water pump 14．给水泵 Feed water pump 15．循环泵 Circulating pump 16．锅炉给水泵 Boiler feed pump 17．卫生水泵 Sanitary pump 18．压载泵 Ballast pump 19．舱底泵 Bilge pump 20．污水泵 Sewage pump 21．燃油泵 Fuel pump 22．高压油泵 High pressure pump 23．底压油泵 Low pressure pump 24．驳运泵 Transfer pump 25．增压泵 Booster pump 26．消防泵 Fire pump 27．通用泵 G.S. pump 28．旋涡泵 Regenerative 29．蜗壳泵 Volute pump 30．导叶泵 Diffuser pump 31．单联泵 Simplex pump 32．双联泵 Duplex pump 33．多联泵 Multiplex pump34．活塞泵 Piston pump35．减摇泵 Anti-roll pump 36．总用泵 General service pump 37．应急消防泵Emergency fire pump 38．扫舱泵 Stripping pump 39．货油泵 Cargo oil pump40．滑油泵 Lubricating oil pump六、甲板机械类（Deck machinery）1．锚机 Windlass2．锚机轴 Windlass shaft3．刹车带 Brake lining4．离合器 Clutch5．锚链轮 Anchor Chain wheel 6．轴承瓦 Bearing bush7．轴承盖 Bearing cover8．绞揽机 Capstan9．系揽绞车 Mooring winch10．卷缆车 Reel11．钢丝绳 Wire rope12．卡环 Shackle13．缆绳 Mooring rope14．滑轮 Block15．刹车装置 Brake device16．制链器 Anchor chain stopper 17．舱盖滚轮 Hatch cover wheel 18．舱盖铰链 Hatch cover hinge 19．液压油缸 Hydraulic jack20．起货机 Cargo winch21．可令吊 Crane22．生活吊 Accommodation crane 23．吊杆 Derrick boom24．桅杆 Mast25．救生艇 Lifeboat26．艇架 Davit27．艇机 Lifeboat capstan28．救生筏 Life raft29．救生衣 Life jacket七、工具类(Word about tools)1．车床 Lathe2．刨床 Planing machine3．钻床 Drill machine4．砂轮机 Grinding machine 5．磨床 Grinder6．铣床 Milling machine7．镗床 Boring machine8．手锤Engineer’s hammer 9．冲击板手 Impact wrench10．板手 Spanner11．活络板手 Screw spanner12．梅花板手 Ring spanner13．呆扳手 Open spanner15．套筒板手 Socket spanner16．管子钳 Pipe spanner17．螺丝刀 Screw driver18．钢丝钳 Wire pliers19．尖嘴钳 Long nose pliers 20．钢锯 Hack saw21．剪刀 Scissors22．手电筒 Torch23．扁铲(凿子) Chisel24．锉刀 File25．丝攻 Thread tap26．板牙 Thread die27．绞刀 Reamer28．刮刀 Scraper29．油石 Oil stone30．拔子(拉马) Puller31．沙布 Emery cloth32．破布 Rag 33．卷尺 Measuring tape34．空心冲 Hole punch35．样冲 Joint punch36．油壶 Oil gun37．牛油枪 Grease gun38．手电钻 Handle drill39．钻头 Drill40．液压千斤 Hydraulic jack.41．塞尺 Feeler gauge42．游标卡尺 Vernier caliper43．外卡尺 Outside calipers44．内卡尺 Inside calipers45．螺纹量规 Screw gauge46．桥规 Bridge gauge47．电焊机 Electrode welding machine48．气焊机 Gas welding machine49．电焊钳 Electric welding pliers50．气割枪 Cutting touch51．电焊条 Electric soldering iron52．电工刀 Electrician knife53．电笔 Test pen54．剥线钳 Wire stripping pliers55．圆规 Compass56．量表 Gauge57．拐档表 Crank deflection gauge58．深度规 Depth gauge59．千分表 Micrometer gauge60．台虎钳 Table vice61．柴油 Diesel oil62．滑油 Lubricating oil63．液压油 Hydraulic oil64．重油 Heavy oil65．燃油 Fuel oil66．黄油 Grease67．螺栓 Bolt68．螺帽 Nut69．垫片 Washer70．研磨沙 Grinding sand71．研磨膏 Grinding paste72．石棉板 Asbestos plate73．青壳纸 Fish paper74．盘根 Packing75．细钢丝 Thin steel wire76．密封圈 Rubber seal ring77．塑料管 Plastic pipe78．胶皮管 Rubber hose79．电灯泡 Electric bulb80．工作灯 Working lamp81．插头 Electric plug82．插座 Electric socket.93．喷砂机 Sand blaster outfit94．空气马达 Air motor95．油柜清洁器 Tank cleaning machine96．高压冲水机High pressure hose forhydraulic97．真空泵 Vacuum pump98．套筒扳手组 Socket wrench set99．深头套筒 Deep socket wrench100．套筒扳手 Box wrench101．单开口扳手 Single open end wrench102．双开口扳手 Double open end wrench103．转矩扳手 Torque wrench104．电动机扳手 Motor wrench105．侧剪钳 Slide cutting plier106．活节钳 Combination plier107．可调快速扳手Speed wrench108．螺丝起子 Screwdriver109．偏向螺丝起子Offset screw110．六角螺帽起子组Hexagon nut drivers set111．手摇钻 Straight hand drill112．手工锯 Hacksaw frame113．锯片 Hacksaw blade114．砂纸 Silicon paper115．手拉葫芦 Chain block116．高压管 High pressure hose117．液压千金顶 Hydraulic jack118．锤子 Hammer119．平錾 Cold chisel120．活动扳手 Adjustable wrench121．螺丝刀 Screwdriver122．侧剪铗 Side cutting hipper123．螺栓剪 Cable cutter124．敲击管钳 Rap wrench125．砂轮 Grinding wheel126．老虎钳 Utility vise127．直梯 Straight ladder128．踏梯 Step ladder129．平台推车 Platform trunk130．搬平车 Gas cylinder carrier131．给油机 Grease lubricator132．强力油泵 Heavy duty pump oiler133．油壶 Oil jag134．麻花钻 Twist drill135．绞刀 Pin reamer136．旋转中心钻Rolling center137．外径测微计Outside micrometer withcounter138．六折式尺 Six-folding rule139．弹性带尺 Convex rule140．不锈钢直尺 Stainless steel straightrule141．平面规 Surface gauge142．平行直角定规Precision flat try square143．温度计 Thermometer八、常用物料(Material in common use)1．阀研磨剂 valve grinding compound2．电焊条 steel electrode3．气焊条 Steel welding wire4．细钢丝绳 Seizing wire5．刚焊条 Steel welding rod6．紫铜管 Copper tube7．乙炔气瓶 Acetylene cylinder8．木屑 Saw dust9．水泥 Cement10．石灰 Lime11．帆布手套 Canvas glove12．垫片 Gasket.13．氧气瓶 Oxygen cylinder14．抹布 Rag15．垫隙片 Shim16．电线 Wire17．电缆 Electric cylinder18．电池 Rag19．灯泡 Bulb20．胶布 Insulating tape21．插头 Plug22．插座 Socket23．保险丝 Fuse24．不锈钢 Stainless steel25．铸铁 Cast iron26．黄铜 Brass27．青铜 Bronze28．铝合金 Aluminium alloy29．橡胶 Rubber30．石棉 Asbestus31．低碳钢 Soft steel32．高碳钢 High-carbon steel33．合金钢 Alloy steel34．木材 Wood35．塑料 Plastic36．球墨铸铁 Nodular iron九、常用紧固件(Part of fixation in common use) 1．螺栓 Bolt2．螺丝 Screw3．螺母 Nut4．方头螺栓 Sq head bolt5．埋头螺栓 Counter sunk head screw 6．套筒螺栓 Socket head bolt7．定位螺栓 Set screw8．十字接头 Cross9．锥形销 Taper pin10．锁紧螺母 Lock nut11．六角头螺栓 Hex head bolt十、常用油类(Oil in common use)1．汽油 Gas oil2．煤油 Kerosene3．润滑油 Lubricating oil4．汽缸油 Cylinder oil5．压缩机油 Compressor oil6．齿轮油 Gear oil7．机油 Motor oil8．凡士林 Vaseline9．燃油 Fuel oil10．油脂 Grease11．柴油 Diesel oil十一、常用量词(Quantifier in common use) 1．件，只，个 Piece2．条，张，片 Sheet3．双 Pair4．套，组，副 Set.5．盒 Box6．箱 Case7．瓶 Bottle8．米 Meter9．厘米 Centimeter10．毫米 Millimeter11．公斤 Kilogram12．克 Gram13．公升 Liter14．平方 Square15．袋 Bag16．码 Yard17．吨 Ton18．磅 Pound19．加仑 Gallon20．立方 Cubic十二、国家名称(Name of country)1．中国 China2．美国 American3．日本 Japan4．英国 Britain5．法国 France6．德国 German7．韩国 South Korea8．希腊 Greece9．泰国 Thailand10．印度 India11．挪威 Norway12．俄罗斯 Russia13．新加坡 Singapore14．澳大利亚 Australia15．伊朗 Iran16．丹麦 Denmark17．加拿大 Canada18．丹麦 Denmark19．芬兰 Finland 20．巴基斯坦 Pakistan21．意大利 Italy十三、常用缩语(abbreviation in common use)1．主机 M/E2．付机 A/E3．阀 V/V4．泵 P/P5．备车 St/by6．完车 F.W.E.7．前进三 FAHD8．微速后退 D.S.Ast9．前进二 H.Ahd10．高压 H.P.11．低压 L.P.12．重油/柴油 H.O./D.O.13．前后 F/A14．左舷 P: port15．无人机舱 UMS16．自动 Auto17．气缸 Cyl18．燃油柜 19．滑油柜 20．沉淀柜 .21．排出 Disc22．吸入 Suct23．柴油柜十四、船用动态常用单词(marine tends word)1．停靠 Alongside2．接近 Approach3．停泊 Berth4．浮筒 Buoy5．码头 Pier6．港口 Port7．移泊 Shift8．航次 Voyage9．试验 Try10．值班 Watch11．航行 Sail十五、船舶机电设备操作词汇(manipulate of marine equipment)1．调整 Adjust2．压载 Ballast3．转换 Change over4．清洁 Clean5．联接 Connect6．排放压载 Deballast7．放残水 Drain8．卸载 Off9．油漆 Paint10．接通 Put on11．吹灰 Soot blown12．开始 Start13．顶端 Top14．洗 Wash15．吹 Blow16．检查 Check17．铲 Chip18．断开 Cut out19．排放 Discharge20．除垢 Descale21．检验 Examine22．受载 On(load)23．用泵排出 Pump out24．调整 Set25．停止 Stop26．调驳 Transfer27．加满 Top up十六、故障常用单词 (words about malfunction)1．失常的 Abnormal2．烧坏 Burn3．堵塞 Clog4．裂缝 Crack5．变形 Deform6．毁坏 Destroy7．磨损 Wear8．出故障 In trouble9．敲击 Knock10．松开 Loose11．不对中 Misalign12．不足的 Insufficient13．失灵 Out of order14．过载 Overload15．过度磨损 Over-worn16．尺寸过大 Oversized17．尺寸过小 Under-sized18．振动 Vibrate19．不平的 Uneven20．不准确 Inaccurate21．全船断电 Black out22．出故障 Fail23．关掉 Shut off24．弯曲 Bend25．停车 Break drown26．腐蚀 Corrode27．腐蚀的 Corrosive28．损坏 Damage29．有毛病的 Faulty30．有缺陷的 Defective31．破裂 Fracture32．卡住 Jam33．漏泄 Leak34．漏泄的 Leaky35．融化 Melt36．噪声 Noise37．过热 Overheat38．咬住 Seize39．紧的 Tight40．松的 Loosen41．发现 Find42．停止 Stop43．脏的 Dirty44．油污的 greasy45．失效的 ineffective46．椭圆形的 oval47．点不着火 misfire48．接错 misjoin49．放错 misplace50．老化 perish51．麻点 pit52．凸起 ridge53．划伤 score54．拉痕 scuff十七、保养检修常用词汇(Words about maintain and examination)1．卡死 Blind2．用卡钳量 Caliper3．关闭 Close4．解体 Disassemble5．安装 Fix6．组装 Box up7．检验 Check8．拆卸 Dismantle9．装配 Fit10．紧固 Fasten11．测量 Gauge12．安装 Install13．测量 Measure14．打开 Open 15．上油漆 Paint 16．换新 Renew 17．上紧 Tighten 18．洗 Wash 19．涂油脂 Grease 20．松开 Loosen 21．加油 Oil22．检修 Overhaul 23．重新组装 Reassemble 24．测取读数 Take reading 25．拧开螺栓 Unbolt 26．抽出 Withdraw十八、常用数字(Numeral in common use) 一 One 二 Two 三 Three 四 Four 五 Five 六 Six 七 Seven 八 Eight 九 Nine 十 Ten 十一 Eleven 十二 Twelve 十三 Thirteen 十四 Fourteen 十五 Fifteen 十六 Sixteen 十七 Seventeen 十八 Eighteen十九 Nineteen 二十 Twenty 三十 Thirty 四十 Forty 五十 Fifty 六十 Sixty 七十 Seventy 八十 Eighty 九十 Ninety 百 Hundred 千 Thousand 万 Ten thousand 百万 Million 第一 First 第二 Second 第三 Third 第四 Fourth 第五 Fifth 第六 Sixth 第七 Seventh 第八 Eighth 第九 Ninth 第十 Tenth 第十一 Eleventh 第十二 Twelfth 第二十 Twentieth十九、时间、季节与方向(Time 、Season and Direction) 1．星期一 Monday 2．星期二 Tuesday 3．星期三 Wednesday 4．星期四 Thursday 5．星期五 Friday 6．星期六 Saturday 7．星期日 Sunday8．春季 Spring 9．夏季 Summer 10．秋季 Autumn 11．冬季 Winter 12．一月 January 13．二月 February 14．三月 March 15．四月 April 16．五月 May 17．六月 June 18．七月 July 19．八月 August 20．九月 September 21．十月 October 22．十一月 November 23．十二月 December 24．小时 Hour 25．分钟 Minute 26．秒 Second 27．月 Month 28．天 Day 29．夜 Night 30．周 Week 31．早晨、上午 Morning 32．下午 Afternoon 33．傍晚 Evening 34．正午 Noon 35．今天 Today 36．昨天 Yesterday 37．明天 Tomorrow 38．前天 The day before yesterday 39．后天 The day after tomorrow 40．本周 This week 41．上周 Last week 42．下周 Next week 43．九月十日 Sep.10th44．去年 Last year 45．明年 Next year 46．上周二 Last Tuesday 47．下周一 Next Monday 48．东 East 49．西 West 50．南 South 51．北 North 52．西北 Northwest 53．东北 Northeast 54．东南 Southeast 55．西南 Southwest 56．世纪 Century 二十、常用词组（Phrases in common use ） 1234．发现不正常 found out of order 5．发现不合标准 found not up to standard 6．发现不准确 found inaccurate 7．发现失去作用 found out of function 8．发现轧住 found seized 9．发现过热 found overheated 10．发现过度磨损 found excessive wear 11．发现过度磨掉 found worn out 12．发现有一点倾斜 found a little bit inclined 13．发现不正常 found abnormal 14．发现因过热而损坏found destroyed by overheating 15．发现龟裂 found chapped 16．发现塌陷 found collapsed 17．发现运转失灵 found out of operation 18．发现呈椭圆形 found oval 19．发现拉痕 found scored 20．发现拉毛 found scuffed 21．发现变形 found deformed 22．发现松动 found loose 23．发现油污 found greasy 24．发现肮脏 found dirty 25．发现咬住 found stuck 26．发现挤压 found squeezed 27．发现弯曲 found bent 28．发现故障 found faulty 29．发现损坏 found damaged30．发现破碎成片 found broken to pieces 31．发现部分剥离 found partly detached 32．发现部分堵塞 found partly choked 33．发现剧烈震动 found violent vibration 34．发现烧坏 found burnt 35．发现断裂 found fractured 36．发现接地 found earthed 37．发现敲缸 found knocking 38．发现溶化 found melted away 39．发现泄漏 found leaking (found leaky) 40．发现冻结 found stuck fast by icing 41．发现锈蚀 found rusty 42．发现失效 found ineffective 43．发现故障 found out of order 44．发现结霜 found frosted 45．发现丢失 found lost 46．发现出故障 found in trouble 47．发现失灵 found out of order 48．发现失灵 found out of action 49．发现不一致 found out of operation 50．发现错位 found out of place 二十一、常用动词和例句(Verb in common use and example) 1．借 borrow 我要向你借这份图纸 I want to borrow the drawing from you. 我可以向你借这个手锤吗? May I borrow the hammer from you? 2．裂 break 阀杆断裂了 The valve spindle is broken. 滚动轴承断裂成碎片了 The ball bearing are broken to pieces. 3．加强 build up 叶轮应该堆焊 The impeller should be built up by welding. 4．烧 burn 电动机烧了 The motor is burnt. 5．进行 carry out 应进行负载试验 The load test should be carried out. 6．吹blow管子必须用压缩空气吹清 The pipe should be blown with compressed air. 7．铸 cast 按原样铸造一个Cast one piece as per sample. 8．引起 cause 损坏是有剧烈振动引起的The damage was caused by violent vibration. 9．倒角 chamfer 油槽须倒角 Oil groove is to be chamfered. 法兰切削后须倒角The flange should bechamfered after being machined.10．换掉 change 把它们换掉,否则我拒绝验收Have them changed, otherwise I refuse toaccept them.11．龟裂 chap轴瓦上的白合金龟裂了The white metal on the bearing bush is chapped.12．核查 check用桥规核查主轴承Check the main bearing with bridge gauge.修理前后要核查拐档Check the crankshaft deflection before and after repair.13．清洁 clean装前须清洁 Clean it before fit back. 14．阻塞 clog燃油滤器阻塞了 The fuel filter is clogged. 15．涂漆 coat用红丹涂管子 Coat the pipe with red lead. 泵壳里涂防护漆The pump casing is to be coated with anti-fouling.16．完成 complete finish你什么时候能完成修理工作?When can you complete (finish) the repair job? 17．连接 connect把电动机和淡水泵连接起来Connect the motor with the fresh water pump 18．腐蚀 corrode泵壳和叶轮均有腐蚀The pump casing and impeller are corroded.19．盖 cover请把所有卸下的部件盖起来Please cover all the removed parts. 20．裂二号缸头裂开穿透至冷却水空间No.2 cylinder head is cracked.21．吊 crane把液压马达吊上岸去修理Crane the hydraulic motor ashore for repair.22．割 cut把底座割掉Cut off the bedplate.23．损坏 damage滚动轴承严重损坏The ball bearings are seriously damaged. 24．脱落 detach白合金部分脱落了The white metal is partly detached.25．查看 detect查看氟里昂系统有无泄漏Detect the Freon system for leakage.26．解体 disassemble解体,清洁并检查高压油泵Disassemble, clean and check the H.P. fuel pump.27．脱开 disconnect把起动空气管脱开Disconnect the starting air pipe.将发电机与原动机脱开。

轮机长常规指令（中英文对照模板）

轮机长常规指令（中英文对照模板）CHIEF ENGINEER’S STANDING ORDER1. All engineer must read the standing order and initial them to indicate understanding thereof and compliance therewith.轮机员需阅读理解完成。

2. Every member of the watch shall be familiar with its assigned watch keeping duties.每人需熟悉指定的职责。

3. You are not to leave the engine room under any circumstances unless received by chief engineer or other engineer.除非有轮机长或轮机员指令，否则不能离开机舱4. The engineer in charge of the watch shall be responsible for the inspection, operation and testing, a s required, of all machinery and equipment under his responsibility. The engineer in charge of a watch is the chief engineer’s representative and his primary responsibility ,at all times, and shall be efficient operation and up-keeping of machinery affecting the safety of the ship.轮机员负责检查/运行/测试机械设备，完成轮机长指令5. The engineer in charge of the watch shall ensure that the established watch keeping arrangements are maintained. Under his general direction engine room ratings, if forming part of the watch shall be required to assist in the safe and efficient operation of the propulsion machinery and auxiliary equipments.轮机员负责安全完成值班6. At the beginning of the engineering watch, the current operational parameters and condition of all machinery shall be verified. Any machinery be not functional properly, excepted to malfunction or requiring special service, shall be noted along with any action already taken. Plants shall be made for any further action if required.值班开始需认真检查，运行不正常的设备，已采取必要措施。

装卸货常用英语口语（水手，三副）

装卸货常用英语口语（水手，三副）一、礼仪用语、介绍及询问等1. 早上好！Good morning.2. 下午好！Good afternoon.3. 晚上好！Good evening.4. 晚安！Good night.5. 请坐Sit down,please.6. 谢谢Thank you.7. 别客气You are welcome.8. 明天见See you tomorrow.9. 下个航次见See you next time.10. 再见！Good bye.11. 你好，你是大副（水手长）吗?Hello, are you Chief officer (Bosun)?12. 你好，我是负责的单船调度员。

Hello, I am the foreman in charge.13. 这位是理货长。

This is Chief Tally.14. 今天谁值班？Who is on duty today?15. 水手长（值班副）在哪儿？Where is Bosun (Duty Officer)?16. 你好，理货房在哪儿？Hi, where is the tallyroom?17. 你值班吗？Are you on duty?18. 是的，什么事？Yes, what’s the matter?19. 你是调度吗？Are you Foreman?20. 是的，你有什么事儿吗？Yes, what can I do for you ?21. 我想见大副，在哪能找到他？I want to see Chief Officer, where can I find him?22. 大副在船上吗？Is Chief Officer on board?二、上船作业前后的辅助工作1. 船梯太高The gangway is too high2. 请落船梯Please lower the gangway3. 船离帮了The ship is far off the wharf4. 请紧缆绳Tighten the line, please.5. 请紧前（后）缆Please tighten the fore (back) line.6. 请向前（向后）绞船Please heave forward (backward)7. 请向前（向后）绞十米Please heave ten meters forward (backward)8. 我们的工人要上船了Our stevedores are going to get on board9. 请在船梯口系好安全网。

船舶轮机英语大全

船舶轮机英语大全第一部分日常用语：Daily EnglishⅠ:问候、介绍、告别（ Greetings、introductions and farewells）1、I’m a fitter (electrician、piper ). 钳工、电工、管子工2、He is an inspector(QC). 检验员3、Welcome to our shipyard.Ⅱ:致谢、道歉（Gratitude and Apologies）1、Do me a favour, please. 请多帮忙2、When shall we deliver it? 提交3、Please wait a moment.4、Will this way take me to the foreign office? 外事办5、Right-about-face向后转Ⅲ Life in the yard1、Have you got used to the life here?2、Please hold the handrails well. 请抓好扶手3、Please use your intercom.（walkie-talkie）对讲机4、How about quality? 质量怎么样？5、There’s something wrong with the drawing.6、Sorry, It’s my fault. 是我的过错7、Don’t worry. That’s easy to deal with.8、Let’s start to check some items. 开始验收吧9、Are you satisfied with it?10、The vibration (temperature、pressure、speed) is normal. 振动（温度、压力、速度）是正常11、Sorry, it has not been finished yet.12、Submission (Delivery) is Okay. 提交（验收）成功常用句型 Common Patterns1、That is an exhaust valve. 排气阀2、These are blowers. 鼓风机3、There are ten workers in our group.4、He is a technician. 技术员5、I am a fitter. 钳工6、When shall we have a check?7、Will you please give me a hand?第二部分管子部分Ⅰ.管子加工后提交用语：Delivery expressions after pipe processing1、Which system is this pipe for?2、How many pipes are there altogether?3、What’s the designed test pressure ? It is 12 kilograms/cm2设计规定的试验压力是多少？ 12公斤/厘米2。

船舶轮机英语集成原版..

船舶英语目录一.职位及工种(Titles and type of work) ····· 1 二、柴油机类(Words about diesel engine) ····· 3 三、船舶机械类(Words about marine machinery) ·· 11 四、阀门(Words about valve) ···· 14 五、泵类(Words about pump) ·········· 16 六、甲板机械类（Deck machinery ）······ 18 七、工具类(Word about tools) ········ 20 八、常用物料(Material in common use) 26 九、常用紧固件(Part of fixation in common use) ··· 28 十、常用油类(Oil in common use) ·····28 十一、常用量词(Quantifier in common use) ·········29 十二、国家名称(Name of country) 。

30 十三、常用缩语(abbreviation in common use) ·····31 十四、船用动态常用单词(marine tends word) 32 十五、船舶机电设备操作词汇(manipulate of marine equipment) ·33 十六、故障常用单词(words about malfunction) ····· 35 十七、保养检修常用词汇(Words about maintain and examination) 38 十八、常用数字(Numeral in common use) 40 十九、时间、季节与方向(Time 、Season and Direction) ·····42 二十常用词组（Phrases in common use ）·45 二十一、常用动词和例句(Verb in common use and example) ····48 二十二、问候和常用表达语(Greeting and common expression) ····67 二十三、主机提交过程用语(Delivery expressions for main engine) 68 二十四、空压机和空气系统用语(Air compressor and Air system) ···· 75 二十五、锅炉提交用语(Delivery expressions for boiler) ···77 二十六、锚绞车提交过程用语(Delivery expressions for anchor windlass) 79 二十七、舵机提交过程用语(Steering gear delivering) ··· 87 二十八、付机提交过程用语（Delivery expression for A/E ）····· 91 二十九、救生艇提交过程用语(Delivery expressions for lifeboat) ··92 三十、其他提交项目 (Delivery expressions for other items) ···95 三十一、甲板机械系泊试验 (Mooring test for deck machinery) ········96 三十二、机舱设备系泊试验 (Mooring test for the equipment in E/R) ···98 三十三、谈论故障常用语（Expressions for trouble ）············100 三十四、谈论检修常用语(Expressions for overhaul) ············101 三十五、谈论试验和检验(Talking about test & check) ···········103 三十六、谈论技术要求(Talking about technology required) (105)一．职位及工种(Titles and type of work) 1．船长 Captain2．大副 Chief officer3．二副 Second officer 4．三副 Third officer 5．四副 Fourth officer 6．水手长 Boatswain7．水手 Sailor & Seaman 8．木匠 Carpenter9．轮机长 Chief engineer 10．大管轮 Second engineer 11．二管轮 Third engineer 12．三管轮 Fourth engineer 13．机匠长 Chief motorman 15．机匠 Fitter 16．加油工 Oil man17．大电 Chief electrician 18．电工 Electrician19．车间主任 Workshop director 20．工长 Section chief 21．班长 Fore man 22．钳工 Fitter23．主管工程师 Engineer in charge 24．机务&船东 Superintendent &Super &Owner 25．助理工程师 Assistant engineer 26．验船师（机）Register 27．验船师（船）Surveyor 28．油漆工 Painter 29．焊工 Welder 30．大橱 Chief cook 31．物料员 Store keeper 32．加油工 Oiler33．机工 Mechanic 34．甲板员 Deck man 35．电线工 Wireman 36．外包工 Laborer 37．铸工 Molder38．管子工 Pipe fitter 39．起重工 Crane operator二、柴油机类(Words about diesel engine) 1．主机 Main engine2．二冲程柴油机 Two-stroke diesel engine 3．四冲程柴油机 Four-stroke diesel engine 4．高速柴油机 High speed diesel engine 5．中速柴油机 Middle speed diesel engine 6．低速柴油机 Low speed diesel engine 7．气缸盖(缸头) Cylinder head 8．安全阀 Safety valve 9．释放阀 Relief valve 10．示功阀 Indicator valve 11．示功考克 Indicator cock 12．空气起动阀 Air starting valve13．起动空气分配器 Air starting distributor 14．油头(燃油喷射器) Fuel injector 15．排气阀 Exhaust valve 16．气缸套 Cylinder liner17．冷却水套 Cooling water jacket 18．气缸注油器 Cylinder lubricator 19．活塞 Piston20．活塞头 Piston crown 21．活塞裙 Piston skirt 22．活塞销 Piston gudgeon pin 24．活塞杆 Piston rod 25．活塞环 Piston ring26．活塞环槽 Piston ring groove 27．压缩环 (气环) Compression ring 28．刮油环 (油环) Oil scraper ring 29．减磨令 Wear ring (copper ring) 30．伸缩管(水拉管) Telescopic pipe 31．活塞冷却空间 Piston cooling space 32．填料箱(函) Stuffing box 33．填料箱密封环Sealing ring for Stuffing box 34．填料箱压缩环 Pressure ring for Stuffing box 35．填料箱刮油环Scraper ring for Stuffing box 36．扫气箱 Scavenging receiver 37．扫气口 Scavenging port 38．排气口 Exhaust port 39．十字头 Cross head 40．十字头销 Crosshead pin 41．十字头轴承 Crosshead bearing 42．十字头滑块 Crosshead slipper 43．滑块 Guide shoe44．十字头导板45．连杆46．连杆大端轴承47．连杆小端轴承48．曲柄轴承49．曲柄销 Crank pin 50．曲轴 Crank shaft 51．曲轴颈 Crank journal 52．曲柄臂 Crank web53．拐档差 Crank deflection 54．主轴承 Main bearing 55．主轴颈 Main journal 56．轴承瓦 Bearing bush57．上轴瓦 Upper bearing bush 58．上轴瓦 Upper half59．下轴瓦 Lower bearing bush 60．下轴瓦 Lower half 61．推力轴承 Thrust bearing 62．推力块 Thrust pad 63．推力盘 Thrust disc 64．推力轴 Thrust shaft 65．底座 Bed plate 66．机架 Frame67．曲柄箱 Crank case68．曲柄箱导门 Crank case door 69．曲柄箱防爆门 Explosion-proof Crank case. 70．定时齿轮 Timing gear 71．飞轮 Flying wheel 72．凸轮 Cam73．凸轮轴 Cam shaft74．喷油凸轮 Fuel injection cam 75．链条 Chain76．链条轮 Chain wheel 77．链条箱 Chain box 78．推杆 Push rod 79．摇臂 Rocker arm 80．排气阀 Exhaust valve 81．吸气阀 Suction valve 82．排气总管 Exhaust manifold 83．进气总管 Air inlet manifold84．高压燃油管 High pressure fuel pipe 85．活塞冷却水管 Piston cooling water pipe 86．法兰 Flange87．贯穿螺栓 Tie bolt (tie rod) 88．端盖 Side cover89．滑油泵 Lubricating oil pump 90．燃油泵 Fuel oil pump 91．滑油泵齿轮 Gear for lubricating oil pump 92．燃油泵齿轮 Gear for fuel oil pump 93．叶轮 Impeller 94．柱塞 Plunger 95．导杆 Guide rod 96．导套 Sleeve97．滚动轴承 Ball bearing 98．滑动轴承 Sliding bearing99．推力滚动轴承Thrust ball bearing 100．推力面 Thrust surface (thrust side) 101．盘车机 Turning gear 102．增压器 Turbocharger 103．涡轮机(透平) Turbine104．涡轮 Turbine wheel 105．涡轮叶片 Turbine blade 106．喷嘴 Nozzle 107．废气叶轮 Exhaust impeller 108．废气叶轮片 Exhaust blade 109．废气端 Exhaust side 110．透平端 Turbine side 111．转子轴 Rotor shaft 112．油泵 L.O.pump 113．换向装置 Reversing device 114．换向伺服期 Reversing servomotor 115．压气机(鼓风机) Blower 116．膨胀接 Expansion joint 117．调速器 governor 118．飞重 Flying weight 119．补偿阀 Compensate valve 120．针阀 Needle valve 121．开口销 Cotter pin 122．轴封 Shaft seal 123．机械密封 Machinery seal 124．配电盘 Switchboard 125．应急配电盘 Emergency switchboard 126．应急发电机 Emergency generator 127．滤器 Filter 128．细滤器 Filter 129．粗滤器 Strainer 130．滑油滤器 L.O. filter 131．燃油滤器 F.O. filter 132．空气消音器 Air intake silencer 132．空气滤器 Air intake filter 133．空气瓶 Air bottle (receiver) 134．分油机 Separator 135．油水分离器 Water-oil separator 136．净油机 Purifier 137．燃油净化器 F.O. purifier 138．二氧化碳 CO2 139．二氧化碳瓶 CO2 bottle 140．正时齿轮 Timing gear 141．导向棒装置 Guide bar 142．注油器驱动 Lubricator driver 143．链条张紧装置 Chain tightener 144．凸轮轴传动轮 Chain wheel on cam shaft 145．中间链链传动轮Intermediate chain wheel 146．注油器驱动装置Lubricator drive 147．链条张紧装置 Chain tightener 148．滚筒导座 Roller guide housing 149．应急操纵台 Emergency console 150．力矩平衡器 Moment compensator 151．主启动阀 Main starting valve 152．启动空气分配器Starting air distributor 153．喷油器 Fuel valve 154．扫气系统 Scavenge air system 155．安全帽 Safety cap 156．机座 Bed plate 157．轴向振动减振器 Axial vibration damper 158．贯穿螺栓 Arrangement of stay bolt 159．示功器驱动装置 Indicator driver 160．端罩 End shields 161．气缸架 Cylinder frame 162．气阀传动装置 Valve operating device 163．摇臂润滑油泵 Rocker arm lubricating oil pump 164．摇臂润滑油柜 Rocker arm lubricating tank 165．摇臂润滑滤器Rocker arm lubricating filter 三、船舶机械类(Words about marine machinery) 1．船用锅炉 Marine boiler 2．废气锅炉 Exhaust boiler 3．辅锅炉 Donkey boiler 4．组合式锅炉 Combined boiler 5．火管 Fire tube 6．给水管 Feed pipe 7．炉膛 Furnace 8．炉墙 Furnace wall 9．火侧 Fire side 10．水侧 Water side 11．燃烧器 Oil burner 12．安全阀 Safety valve 13．上排污 Upper drain 14．下排污 Lower drain 15．锅炉皮阀 Mounting valve 16．水位计 Water level gauge 17．压力表 Pressure gauge 18．主汽门 Main steam valve 19．玻璃管 Glass tube 20．空调装置 Air-conditioning plant 21．制冷装置 Refrigerating plant 22．冰机 Fridge. Machine 23．空气压缩机 Air compressor 24．造水机 Fresh water generator 25．板式冷却器 Plate type cooler 26．机舱天车 Engine room crane 27．天车导轨 Crane rail 28．电磁阀 Solenoid valve 29．舵机 Steering gear 30．舵承 Rudder bearing carrier 31．液压缸 Hydraulic cylinder 32．废气涡轮增压器Exhaust gas turbocharger 33．弹簧阀 Spring loaded valve 34．冷凝器 Condenser 35．分油器 Oil separator 36．轴带发电机 Shaft generator 37．焚烧炉 Oil burner 38．分油机 Separator 39．分离筒 Separator bowl 40．配水盘装置 Paring disc device 41．转数计 Revolution counter 42．控制阀 Control valve 43．辅机 Auxiliary machinery 44．制冷装置 Refrigerating plant 45．海水淡化装置Sea water desalting plant 46．热交换器 Heat exchanger 47．船用气瓶 Marine air bottle 48．冷风机 Cooler unit 49．防水风门 Fire damper 50．气密挡板 Gas tight damper 51．排气风机 Exhaust fan 52．舱室通风机 Cabin fan 53．机舱通风机 Engine room fan 54．应急鼓风机 Emergency blower 四、阀门(Words about valve) 1．吸气阀 Suction valve 2．排气阀 Exhaust valve 3．控制阀 Control valve 4．导阀 Pilot valve 5．单向阀 Non-return valve 6．口琴阀 Flap valve 7．调节阀 Regulating valve 8．液压阀 Hydraulic valve 9．膨胀阀 Expansion valve 10．给水阀 Feed valve 11．排水阀 Discharge valve 12．截止阀 Stop valve 13．吹泄阀 Blow-off valve 14．空气阀 Air valve 15．泄放阀 Drain valve 16．止回阀 Check valve 17．海底阀 Sea valve 18．回流阀 Retune valve 19．节流阀 Throttle valve 20．进气阀 Inlet valve 21．出气阀 Outlet valve 22．热力阀 Thermal valve 23．中央阀 Center valve 24．单向阀 One way valve 25．二通阀 Two way valve 26．三通阀 Triple valve 27．旁通阀 By-pass valve 28．换向阀 Change-over valve 29．减压阀 Pressure-reducing valve 30．溢流阀 Overflow valve 31．自闭阀 Self-locking valve 32．针阀 Needle valve 33．平衡阀 Balance valve 34．循环阀 Circulation valve 35．主阀 Main valve 36．滑阀 Slide valve 37．蝶阀 Butter-fly valve 38．截止阀 Shut-off valve 39．闸板阀 Gate valve 40．通海阀 Sea suction valve 41．吹除阀 Sea chest cleaning valve 42．防浪阀 Storm valve 43．舱壁阀 Bulkhead valve 44．快关阀 Emergency shut off valve 45．呼吸阀 Breather valve 五、泵类(Words about pump) 1．电动泵 Motor-driven pump 2．柱塞泵 Plunger pump 3．叶片泵 Vane pump 4．回转泵 Rotary pump 5．齿轮泵 Gear pump 6．往复泵 Reciprocating pump 7．离心泵 Centrifugal pump 1．电动泵 Motor-driven pump 2．柱塞泵 Plunger pump 3．叶片泵 Vane pump 4．回转泵 Rotary pump 5．齿轮泵 Gear pump 6．往复泵 Reciprocating pump 7．离心泵 Centrifugal pump 8．真空泵 Vacuum pump 9．螺杆泵 Screw pump 10．喷射泵 Ejector pump 11．冷却泵 Cooling pump 12．淡水泵 Fresh water pump 13．海水泵 Sea water pump 14．给水泵 Feed water pump 15．循环泵 Circulating pump 16．锅炉给水泵 Boiler feed pump 17．卫生水泵 Sanitary pump 18．压载泵 Ballast pump 19．舱底泵 Bilge pump 20．污水泵 Sewage pump 21．燃油泵 Fuel pump 22．高压油泵 High pressure pump 23．底压油泵 Low pressure pump 24．驳运泵 Transfer pump 25．增压泵 Booster pump 26．消防泵 Fire pump 27．通用泵 G.S. pump 28．旋涡泵 Regenerative 29．蜗壳泵 Volute pump 30．导叶泵 Diffuser pump 31．单联泵 Simplex pump 32．双联泵 Duplex pump 33．多联泵 Multiplex pump34．活塞泵 Piston pump35．减摇泵 Anti-roll pump 36．总用泵 General service pump 37．应急消防泵Emergency fire pump 38．扫舱泵 Stripping pump 39．货油泵 Cargo oil pump40．滑油泵 Lubricating oil pump六、甲板机械类（Deck machinery）1．锚机 Windlass2．锚机轴 Windlass shaft3．刹车带 Brake lining4．离合器 Clutch5．锚链轮 Anchor Chain wheel 6．轴承瓦 Bearing bush7．轴承盖 Bearing cover8．绞揽机 Capstan9．系揽绞车 Mooring winch10．卷缆车 Reel11．钢丝绳 Wire rope12．卡环 Shackle13．缆绳 Mooring rope14．滑轮 Block15．刹车装置 Brake device16．制链器 Anchor chain stopper 17．舱盖滚轮 Hatch cover wheel 18．舱盖铰链 Hatch cover hinge 19．液压油缸 Hydraulic jack20．起货机 Cargo winch21．可令吊 Crane22．生活吊 Accommodation crane 23．吊杆 Derrick boom24．桅杆 Mast25．救生艇 Lifeboat26．艇架 Davit27．艇机 Lifeboat capstan28．救生筏 Life raft29．救生衣 Life jacket七、工具类(Word about tools)1．车床 Lathe2．刨床 Planing machine3．钻床 Drill machine4．砂轮机 Grinding machine 5．磨床 Grinder6．铣床 Milling machine7．镗床 Boring machine8．手锤Engineer’s hammer 9．冲击板手 Impact wrench10．板手 Spanner11．活络板手 Screw spanner12．梅花板手 Ring spanner13．呆扳手 Open spanner15．套筒板手 Socket spanner16．管子钳 Pipe spanner17．螺丝刀 Screw driver18．钢丝钳 Wire pliers19．尖嘴钳 Long nose pliers 20．钢锯 Hack saw21．剪刀 Scissors22．手电筒 Torch23．扁铲(凿子) Chisel24．锉刀 File25．丝攻 Thread tap26．板牙 Thread die27．绞刀 Reamer28．刮刀 Scraper29．油石 Oil stone30．拔子(拉马) Puller31．沙布 Emery cloth32．破布 Rag 33．卷尺 Measuring tape34．空心冲 Hole punch35．样冲 Joint punch36．油壶 Oil gun37．牛油枪 Grease gun38．手电钻 Handle drill39．钻头 Drill40．液压千斤 Hydraulic jack.41．塞尺 Feeler gauge42．游标卡尺 Vernier caliper43．外卡尺 Outside calipers44．内卡尺 Inside calipers45．螺纹量规 Screw gauge46．桥规 Bridge gauge47．电焊机 Electrode welding machine48．气焊机 Gas welding machine49．电焊钳 Electric welding pliers50．气割枪 Cutting touch51．电焊条 Electric soldering iron52．电工刀 Electrician knife53．电笔 Test pen54．剥线钳 Wire stripping pliers55．圆规 Compass56．量表 Gauge57．拐档表 Crank deflection gauge58．深度规 Depth gauge59．千分表 Micrometer gauge60．台虎钳 Table vice61．柴油 Diesel oil62．滑油 Lubricating oil63．液压油 Hydraulic oil64．重油 Heavy oil65．燃油 Fuel oil66．黄油 Grease67．螺栓 Bolt68．螺帽 Nut69．垫片 Washer70．研磨沙 Grinding sand71．研磨膏 Grinding paste72．石棉板 Asbestos plate73．青壳纸 Fish paper74．盘根 Packing75．细钢丝 Thin steel wire76．密封圈 Rubber seal ring77．塑料管 Plastic pipe78．胶皮管 Rubber hose79．电灯泡 Electric bulb80．工作灯 Working lamp81．插头 Electric plug82．插座 Electric socket.93．喷砂机 Sand blaster outfit94．空气马达 Air motor95．油柜清洁器 Tank cleaning machine96．高压冲水机High pressure hose forhydraulic97．真空泵 Vacuum pump98．套筒扳手组 Socket wrench set99．深头套筒 Deep socket wrench100．套筒扳手 Box wrench101．单开口扳手 Single open end wrench102．双开口扳手 Double open end wrench103．转矩扳手 Torque wrench104．电动机扳手 Motor wrench105．侧剪钳 Slide cutting plier106．活节钳 Combination plier107．可调快速扳手Speed wrench108．螺丝起子 Screwdriver109．偏向螺丝起子Offset screw110．六角螺帽起子组Hexagon nut drivers set111．手摇钻 Straight hand drill112．手工锯 Hacksaw frame113．锯片 Hacksaw blade114．砂纸 Silicon paper115．手拉葫芦 Chain block116．高压管 High pressure hose117．液压千金顶 Hydraulic jack118．锤子 Hammer119．平錾 Cold chisel120．活动扳手 Adjustable wrench121．螺丝刀 Screwdriver122．侧剪铗 Side cutting hipper123．螺栓剪 Cable cutter124．敲击管钳 Rap wrench125．砂轮 Grinding wheel126．老虎钳 Utility vise127．直梯 Straight ladder128．踏梯 Step ladder129．平台推车 Platform trunk130．搬平车 Gas cylinder carrier131．给油机 Grease lubricator132．强力油泵 Heavy duty pump oiler133．油壶 Oil jag134．麻花钻 Twist drill135．绞刀 Pin reamer136．旋转中心钻Rolling center137．外径测微计Outside micrometer withcounter138．六折式尺 Six-folding rule139．弹性带尺 Convex rule140．不锈钢直尺 Stainless steel straightrule141．平面规 Surface gauge142．平行直角定规Precision flat try square143．温度计 Thermometer八、常用物料(Material in common use)1．阀研磨剂 valve grinding compound2．电焊条 steel electrode3．气焊条 Steel welding wire4．细钢丝绳 Seizing wire5．刚焊条 Steel welding rod6．紫铜管 Copper tube7．乙炔气瓶 Acetylene cylinder8．木屑 Saw dust9．水泥 Cement10．石灰 Lime11．帆布手套 Canvas glove12．垫片 Gasket.13．氧气瓶 Oxygen cylinder14．抹布 Rag15．垫隙片 Shim16．电线 Wire17．电缆 Electric cylinder18．电池 Rag19．灯泡 Bulb20．胶布 Insulating tape21．插头 Plug22．插座 Socket23．保险丝 Fuse24．不锈钢 Stainless steel25．铸铁 Cast iron26．黄铜 Brass27．青铜 Bronze28．铝合金 Aluminium alloy29．橡胶 Rubber30．石棉 Asbestus31．低碳钢 Soft steel32．高碳钢 High-carbon steel33．合金钢 Alloy steel34．木材 Wood35．塑料 Plastic36．球墨铸铁 Nodular iron九、常用紧固件(Part of fixation in common use) 1．螺栓 Bolt2．螺丝 Screw3．螺母 Nut4．方头螺栓 Sq head bolt5．埋头螺栓 Counter sunk head screw 6．套筒螺栓 Socket head bolt7．定位螺栓 Set screw8．十字接头 Cross9．锥形销 Taper pin10．锁紧螺母 Lock nut11．六角头螺栓 Hex head bolt十、常用油类(Oil in common use)1．汽油 Gas oil2．煤油 Kerosene3．润滑油 Lubricating oil4．汽缸油 Cylinder oil5．压缩机油 Compressor oil6．齿轮油 Gear oil7．机油 Motor oil8．凡士林 Vaseline9．燃油 Fuel oil10．油脂 Grease11．柴油 Diesel oil十一、常用量词(Quantifier in common use) 1．件，只，个 Piece2．条，张，片 Sheet3．双 Pair4．套，组，副 Set.5．盒 Box6．箱 Case7．瓶 Bottle8．米 Meter9．厘米 Centimeter10．毫米 Millimeter11．公斤 Kilogram12．克 Gram13．公升 Liter14．平方 Square15．袋 Bag16．码 Yard17．吨 Ton18．磅 Pound19．加仑 Gallon20．立方 Cubic十二、国家名称(Name of country)1．中国 China2．美国 American3．日本 Japan4．英国 Britain5．法国 France6．德国 German7．韩国 South Korea8．希腊 Greece9．泰国 Thailand10．印度 India11．挪威 Norway12．俄罗斯 Russia13．新加坡 Singapore14．澳大利亚 Australia15．伊朗 Iran16．丹麦 Denmark17．加拿大 Canada18．丹麦 Denmark19．芬兰 Finland 20．巴基斯坦 Pakistan21．意大利 Italy十三、常用缩语(abbreviation in common use)1．主机 M/E2．付机 A/E3．阀 V/V4．泵 P/P5．备车 St/by6．完车 F.W.E.7．前进三 FAHD8．微速后退 D.S.Ast9．前进二 H.Ahd10．高压 H.P.11．低压 L.P.12．重油/柴油 H.O./D.O.13．前后 F/A14．左舷 P: port15．无人机舱 UMS16．自动 Auto17．气缸 Cyl18．燃油柜 19．滑油柜 20．沉淀柜 .21．排出 Disc22．吸入 Suct23．柴油柜十四、船用动态常用单词(marine tends word)1．停靠 Alongside2．接近 Approach3．停泊 Berth4．浮筒 Buoy5．码头 Pier6．港口 Port7．移泊 Shift8．航次 Voyage9．试验 Try10．值班 Watch11．航行 Sail十五、船舶机电设备操作词汇(manipulate of marine equipment)1．调整 Adjust2．压载 Ballast3．转换 Change over4．清洁 Clean5．联接 Connect6．排放压载 Deballast7．放残水 Drain8．卸载 Off9．油漆 Paint10．接通 Put on11．吹灰 Soot blown12．开始 Start13．顶端 Top14．洗 Wash15．吹 Blow16．检查 Check17．铲 Chip18．断开 Cut out19．排放 Discharge20．除垢 Descale21．检验 Examine22．受载 On(load)23．用泵排出 Pump out24．调整 Set25．停止 Stop26．调驳 Transfer27．加满 Top up十六、故障常用单词 (words about malfunction)1．失常的 Abnormal2．烧坏 Burn3．堵塞 Clog4．裂缝 Crack5．变形 Deform6．毁坏 Destroy7．磨损 Wear8．出故障 In trouble9．敲击 Knock10．松开 Loose11．不对中 Misalign12．不足的 Insufficient13．失灵 Out of order14．过载 Overload15．过度磨损 Over-worn16．尺寸过大 Oversized17．尺寸过小 Under-sized18．振动 Vibrate19．不平的 Uneven20．不准确 Inaccurate21．全船断电 Black out22．出故障 Fail23．关掉 Shut off24．弯曲 Bend25．停车 Break drown26．腐蚀 Corrode27．腐蚀的 Corrosive28．损坏 Damage29．有毛病的 Faulty30．有缺陷的 Defective31．破裂 Fracture32．卡住 Jam33．漏泄 Leak34．漏泄的 Leaky35．融化 Melt36．噪声 Noise37．过热 Overheat38．咬住 Seize39．紧的 Tight40．松的 Loosen41．发现 Find42．停止 Stop43．脏的 Dirty44．油污的 greasy45．失效的 ineffective46．椭圆形的 oval47．点不着火 misfire48．接错 misjoin49．放错 misplace50．老化 perish51．麻点 pit52．凸起 ridge53．划伤 score54．拉痕 scuff十七、保养检修常用词汇(Words about maintain and examination)1．卡死 Blind2．用卡钳量 Caliper3．关闭 Close4．解体 Disassemble5．安装 Fix6．组装 Box up7．检验 Check8．拆卸 Dismantle9．装配 Fit10．紧固 Fasten11．测量 Gauge12．安装 Install13．测量 Measure14．打开 Open 15．上油漆 Paint 16．换新 Renew 17．上紧 Tighten 18．洗 Wash 19．涂油脂 Grease 20．松开 Loosen 21．加油 Oil22．检修 Overhaul 23．重新组装 Reassemble 24．测取读数 Take reading 25．拧开螺栓 Unbolt 26．抽出 Withdraw十八、常用数字(Numeral in common use) 一 One 二 Two 三 Three 四 Four 五 Five 六 Six 七 Seven 八 Eight 九 Nine 十 Ten 十一 Eleven 十二 Twelve 十三 Thirteen 十四 Fourteen 十五 Fifteen 十六 Sixteen 十七 Seventeen 十八 Eighteen十九 Nineteen 二十 Twenty 三十 Thirty 四十 Forty 五十 Fifty 六十 Sixty 七十 Seventy 八十 Eighty 九十 Ninety 百 Hundred 千 Thousand 万 Ten thousand 百万 Million 第一 First 第二 Second 第三 Third 第四 Fourth 第五 Fifth 第六 Sixth 第七 Seventh 第八 Eighth 第九 Ninth 第十 Tenth 第十一 Eleventh 第十二 Twelfth 第二十 Twentieth十九、时间、季节与方向(Time 、Season and Direction) 1．星期一 Monday 2．星期二 Tuesday 3．星期三 Wednesday 4．星期四 Thursday 5．星期五 Friday 6．星期六 Saturday 7．星期日 Sunday8．春季 Spring 9．夏季 Summer 10．秋季 Autumn 11．冬季 Winter 12．一月 January 13．二月 February 14．三月 March 15．四月 April 16．五月 May 17．六月 June 18．七月 July 19．八月 August 20．九月 September 21．十月 October 22．十一月 November 23．十二月 December 24．小时 Hour 25．分钟 Minute 26．秒 Second 27．月 Month 28．天 Day 29．夜 Night 30．周 Week 31．早晨、上午 Morning 32．下午 Afternoon 33．傍晚 Evening 34．正午 Noon 35．今天 Today 36．昨天 Yesterday 37．明天 Tomorrow 38．前天 The day before yesterday 39．后天 The day after tomorrow 40．本周 This week 41．上周 Last week 42．下周 Next week 43．九月十日 Sep.10th44．去年 Last year 45．明年 Next year 46．上周二 Last Tuesday 47．下周一 Next Monday 48．东 East 49．西 West 50．南 South 51．北 North 52．西北 Northwest 53．东北 Northeast 54．东南 Southeast 55．西南 Southwest 56．世纪 Century 二十、常用词组（Phrases in common use ） 1234．发现不正常 found out of order 5．发现不合标准 found not up to standard 6．发现不准确 found inaccurate 7．发现失去作用 found out of function 8．发现轧住 found seized 9．发现过热 found overheated 10．发现过度磨损 found excessive wear 11．发现过度磨掉 found worn out 12．发现有一点倾斜 found a little bit inclined 13．发现不正常 found abnormal 14．发现因过热而损坏found destroyed by overheating 15．发现龟裂 found chapped 16．发现塌陷 found collapsed 17．发现运转失灵 found out of operation 18．发现呈椭圆形 found oval 19．发现拉痕 found scored 20．发现拉毛 found scuffed 21．发现变形 found deformed 22．发现松动 found loose 23．发现油污 found greasy 24．发现肮脏 found dirty 25．发现咬住 found stuck 26．发现挤压 found squeezed 27．发现弯曲 found bent 28．发现故障 found faulty 29．发现损坏 found damaged30．发现破碎成片 found broken to pieces 31．发现部分剥离 found partly detached 32．发现部分堵塞 found partly choked 33．发现剧烈震动 found violent vibration 34．发现烧坏 found burnt 35．发现断裂 found fractured 36．发现接地 found earthed 37．发现敲缸 found knocking 38．发现溶化 found melted away 39．发现泄漏 found leaking (found leaky) 40．发现冻结 found stuck fast by icing 41．发现锈蚀 found rusty 42．发现失效 found ineffective 43．发现故障 found out of order 44．发现结霜 found frosted 45．发现丢失 found lost 46．发现出故障 found in trouble 47．发现失灵 found out of order 48．发现失灵 found out of action 49．发现不一致 found out of operation 50．发现错位 found out of place 二十一、常用动词和例句(Verb in common use and example) 1．借 borrow 我要向你借这份图纸 I want to borrow the drawing from you. 我可以向你借这个手锤吗? May I borrow the hammer from you? 2．裂 break 阀杆断裂了 The valve spindle is broken. 滚动轴承断裂成碎片了 The ball bearing are broken to pieces. 3．加强 build up 叶轮应该堆焊 The impeller should be built up by welding. 4．烧 burn 电动机烧了 The motor is burnt. 5．进行 carry out 应进行负载试验 The load test should be carried out. 6．吹blow管子必须用压缩空气吹清 The pipe should be blown with compressed air. 7．铸 cast 按原样铸造一个Cast one piece as per sample. 8．引起 cause 损坏是有剧烈振动引起的The damage was caused by violent vibration. 9．倒角 chamfer 油槽须倒角 Oil groove is to be chamfered. 法兰切削后须倒角The flange should bechamfered after being machined.10．换掉 change 把它们换掉,否则我拒绝验收Have them changed, otherwise I refuse toaccept them.11．龟裂 chap轴瓦上的白合金龟裂了The white metal on the bearing bush is chapped.12．核查 check用桥规核查主轴承Check the main bearing with bridge gauge.修理前后要核查拐档Check the crankshaft deflection before and after repair.13．清洁 clean装前须清洁 Clean it before fit back. 14．阻塞 clog燃油滤器阻塞了 The fuel filter is clogged. 15．涂漆 coat用红丹涂管子 Coat the pipe with red lead. 泵壳里涂防护漆The pump casing is to be coated with anti-fouling.16．完成 complete finish你什么时候能完成修理工作?When can you complete (finish) the repair job? 17．连接 connect把电动机和淡水泵连接起来Connect the motor with the fresh water pump 18．腐蚀 corrode泵壳和叶轮均有腐蚀The pump casing and impeller are corroded.19．盖 cover请把所有卸下的部件盖起来Please cover all the removed parts. 20．裂二号缸头裂开穿透至冷却水空间No.2 cylinder head is cracked.21．吊 crane把液压马达吊上岸去修理Crane the hydraulic motor ashore for repair.22．割 cut把底座割掉Cut off the bedplate.23．损坏 damage滚动轴承严重损坏The ball bearings are seriously damaged. 24．脱落 detach白合金部分脱落了The white metal is partly detached.25．查看 detect查看氟里昂系统有无泄漏Detect the Freon system for leakage.26．解体 disassemble解体,清洁并检查高压油泵Disassemble, clean and check the H.P. fuel pump.27．脱开 disconnect把起动空气管脱开Disconnect the starting air pipe.将发电机与原动机脱开。