太阳能充电器使用说明书
太阳能电池板智能充电器使用说明书
太阳能电池板智能充电器使用说明书充电及超压指示：当系统连接正常，且有阳光照射到光电池板时，充电指示灯(1)为绿色常亮，表示系统充电电路正常；当充电指示灯(1)出现绿色快速闪烁时，说明系统过电压，处理见故障处理内容；充电过程使用了PWM方式，如果发生过过放动作，充电先要达到提升充电电压，并保持30分钟，而后降到直充电压，保持30分钟，以激活蓄电池，避免硫化结晶，最后降到浮充电压，并保持浮充电压。
如果没有发生过放，将不会有提升充电方式，以防蓄电池失水。
这些自动控制过程将使蓄电池达到最佳充电效果并保证或延长其使用寿命。
蓄电池状态指示：蓄电池电压在正常范围时，状态指示灯(2)为绿色常亮；充满后状态指示灯为绿色慢闪；当电池电压降低到欠压时状态指示灯变成橙黄色；当蓄电池电压继续降低到过放电压时，状态指示灯(2)变为红色，此时控制器将自动关闭输出，提醒用户及时补充电能。
当电池电压恢复到正常工作范围内时，将自动使能输出开通动作，状态指示灯(2)变为绿色；负载指示：当负载开通时，负载指示灯(4)常亮。
如果负载电流超过了控制器1.25倍的额定电流60秒时，或负载电流超过了控制器1.5倍的额定电流5秒时，故障指示灯(3)为红色慢闪，表示过载，控制器将关闭输出。
当负载或负载侧出现短路故障时，控制器将立即关闭输出，故障指示灯(3)快闪。
出现上述现象时，用户应当仔细检查负载连接情况，断开有故障的负载后，按一次按键即恢复正常输出。
负载开关操作：控制器上电后默认负载输出为关闭，在正常情况下，每按一次按键，负载输出即改变一次开关状态。
当负载输出为开时，负载指示灯(4)常亮；当负载为关闭时，负载指示灯(4)常灭；当负载过载时，故障指示灯(3)慢速闪烁，当负载发生短路时，故障载指示灯(3)快速闪烁。
负载过载或短路控制器均会关闭输出。
第一次发生负载短路30秒后自动恢复输出若还没排出短路故障只能手动恢复输出。
如复位过载、短路保护，排出负载的短路或过载故障，按一次按键，即恢复正常输出。
MPPT2024Z 太阳能充放电控制器使用手册说明书
MPPT2024Z 太阳能充放电控制器使用手册安装、使用前请仔细阅读该手册 武汉万鹏科技有限公司 h t t p ://w w w .j u t a s o l a r .c o m 武汉万鹏科技有限公司 ht t p ://w w w.j u t a s o l a r .c o m 科技有限公司t a s o l a r .c o mMPPT2024Z 太阳能充放电控制器使用手册 版本V1.1目录 1. 安全事项............................................................................................................3 2. MPPT2024Z 控制器介绍.....................................................................................3 2.1 产品概述..................................................................................................3 2.2 产品结构..................................................................................................3 2.3 产品功能..................................................................................................4 2.4 最大功率点跟踪（MPPT）技术介绍......................................................6 3.系统规划参考....................................................................................................7 3.1 系统电压等级..........................................................................................7 3.2 太阳能电池配置......................................................................................8 3.3 配线..........................................................................................................8 3.4 过流保护..................................................................................................9 3.5 雷击保护..................................................................................................9 3.6 接地..........................................................................................................9 3.7 系统扩容..................................................................................................9 4.安装说明..........................................................................................................10 4.1 产品外形尺寸........................................................................................10 4.2 系统接线示意图....................................................................................11 4.3 线材工具准备........................................................................................11 4.4 安装过程................................................................................................11 5.使用说明..........................................................................................................12 5.1 按键功能说明........................................................................................12 5.2 LED 指示状态说明.................................................................................12 5.3 系统类型查看........................................................................................13 6.故障处理..........................................................................................................13 6.1 控制器保护后处理方法........................................................................13 6.2 常见故障现象及处理方法....................................................................14 7.技术参数..........................................................................................................15 8. 保修承诺. (16)武汉万鹏科技有限公司 h tt p ://w w w .j u t a s o l a r .c o m 武汉万鹏科技有限公司 ht t p ://w w w.j u t a s o l a r .c o m 科技有限公司 t a s o l a r .c o mMPPT2024Z 太阳能充放电控制器使用手册 版本V1.1尊敬的用户： 非常感谢您选用我们公司的产品！我们将为您的太阳能发电系统提供长久可靠的服务！ 该手册提供产品的安装、使用、维护等相关的指导，使用前请仔细阅读该手册。
太阳能充电控制器使用说明书
风光互补+LED 恒流一体机使用说明书■ 主要特点：1、本公司自主研发新型风光互补降压型MPPT + LED 升压型恒流一体机控制器；2、具有蓄电池浮充、涓充、过充、过放、反接保护；风机电子卸荷、转速检测、自动刹车、手动刹车保护；负载恒流输出、降功率调节、电子短路、过载保护；太阳能独特的防反接、防反充保护等全自动控制；以上保护均不损坏任何部件。
3、风力发电机采用独特的降压型MPPT 功能，具有转速检测、过速保护，风机过充自动卸荷、恒压、限流充电功能；风机转速和刹车恢复时间都可随意设定、修改；4、太阳能也采用了降压型MPPT 功能，串联式充电主回路，使充电回路的电压损失较使用二极管的充电电路降低近一半，充电效率较非PWM 高3%-6%，增加了用电时间；过放恢复的提升充电，正常的直充，浮充自动控制方式使系统有更长的使用寿命；同时具有高精度温度补偿。
5、负载使用升压型恒流方式，转换效率可达98%，可在线调整LED 输出电流，电流从30mA —3300mA 可调，并且可分四个时段，分别对亮灯时控、功率进行调节。
6、直观的LED 发光管指示当前系统运行状态，通过指示灯可以清楚的了解系统使用情况，以及故障报警状态。
7、所有控制全部采用工业级芯片，能在寒冷、高温、潮湿环境运行自如。
同时使用了晶振定时控制，定时控制精确。
8、使用了直观的LED 数码管显示设置，一键式操作即可完成所有设置，定时时间与数码管显示数字一一对应,显示更直观。
9、外壳防水采用独特的结构设计，使得外壳与散热片之间密封结合，只需将端子一面朝下安装，皆可起到安全的防水效果，顶端有安装挂件孔，即方便了安装，也起到了防水作用，同时大型散热片更加达到良好的散热效果，可有效延长控制器的使用寿命。
■ 控制器面板图:■ 系统说明：本控制器专为风力发电和太阳能发电直流供电系统、LED 照明设备设计专用，使用了专业电脑芯片的智能化控制。
采用一键式轻触开关，可完成所有操作及设置。
Ceyone 太阳能充电器套件用户手册说明书
SOLAR KITA SUSTAINABLE BATTERY CHARGING GEAR User ManualWSBC-50Contents1. General Information (1)1.1 Key Design Features (1)1.2 Warnings (2)2. Components and accessories (3)2.1 Accessories (3)3. Specifications (4)3.1 Module electrical specifications (4)3.2 Module mechanical specifications (4)3.3 Charge controller specifications (4)3.4 Rooftop box specifications (5)4. Packaging information (6)5. Installation (7)5.1 Wiring guidelines (7)5.2 Kit fixation guidelines (8)6. Operating Instructions (9)6.1 Charge controller (9)6.2 Features of charge controller (9)6.3 Display symbols (9)6.4 Special Instructions (10)7. Troubleshooting (10)8. Frequently Asked Questions (11)9. Limited Warranty (11)User manual – Ceyone solar kit1.General InformationPlease read this user manual carefully before using the product.Dear Customer,Thank you for purchasing Ceyone solar kit.We hope that you get best results from our product which has been manufactured with high quality and state of the art technology. Please read this entire user manual and all its accompanying documents carefully before using the product. Keep this manual and its accompanying documents safe/stored to refer them in the future.1.1 Key Design FeaturesSuperior product efficiencies as per international benchmarksOur high quality components are designed for best in class product durabilityMaximizes the state of charge of the battery which ensures that the lifetime ofbattery is extendedAdequate protection ensuring hazard free operationDesigned for off-grid applications1.2 WarningsPlease read all the warnings carefully before operating the product. It is necessary to understand and keep them in mind when the system is in use. Any negligence may lead to severe damage to you and your surroundings.Disconnect all the operating battery Exceeding current and voltage rating Use in presence ofponents and accessories2.1 Accessories3.Specifications3.1 Module electrical specificationsThe figure below shows the performance curve of 50Wp module under Standard Test Conditions (STC): 1000 W/m 2 irradiance, Air Mass 1.5 and 25°C cell temperature.3.2 Module mechanical specifications3.3 Charge controller specifications3.4 Rooftop box specifications3.5 Mounting kit specifications4.Packaging information1.Rooftop box2.Charge controller3.Mounting bracket & fixing ancillariesNote: These additional inclusions are kept in position by utilizing double sided tape. Exercise caution whenremoving/ detaching the accessories.5. Installation5.1 Wiring guidelinesIn order to achieve optimized output, it is recommended to that the electrical connections are made in the correct manner using 14 gauge wire. Verify that the connections are secure to ensure safe operation of the kit. It is recommended to use a 10 amp rated fuse before the battery for enhanced safety. As a precaution use properly insulated tools & appropriate PPE’s.Line Diagram Of ConnectionExterior Wiring Guide10 Amp Fuse 14 GaugeWire5.2 Kit fixation guidelinesThe following steps should be adhered to for kit installation/ fixation.1.Connecting the rooftop box: The solar panel need to be connected to the rooftop box as shown in wiringdiagram. Please use appropriate mating connectors between the inter-connecting wire(s) to ensure safe operation.2.Fixing rooftop box atop vehicle: The rooftop box should be fixed atop the vehicle. It is recommended touse appropriate sealant & dispenser for this operation. Kindly allow the sealant to dry for minimum of 6~8 hours in a moisture free environment to obtain a permanent bond.3.Fixing the mounting structure on solar module: Use the 4 mounting clamps and fix each of themalongside the mounting hole as provided in the rear side of the module.4.Fixing ancillaries: Follow the mounting process by utilizing M6 bolt, M6 split lock washer, M6 flat washeron one side of the mounting clamp Lock the bolt by in position by utilizing M6 flat washer and M6 nut on the other side. Use appropriate tools like Spanner, Plier, etc. for obtaining a perfect fit. Connecting the rooftop box Fixing rooftop box atop vehicleModule fixation guide Mounting kit fixation guide6.Operating Instructions6.1 Charge controllerBefore making initial connections, please ensure thatthe battery has enough charge or is at adequatevoltage level such that the controller can sense thebattery.The controller is only suitable for LEAD ACIDBATTERIES: OPEN, AGM, and GEL type. It is notsuited for nickel metal hydride, lithium ions or otherbatteries. Charge controller is only suitable ofcontrolling solar PV modules as input. Never connectanother charging source to the charge controller.6.2 Features of charge controller1.The PMW charge controller is IP 68 with built-in open circuit and reverse protection2.It is equipped with dual mosfet for reverse current and low heat protection3.It has enhanced size of display for clearly observing and recording the dataDisplay the battery voltageIndication that the solar panel is charging the batteryDisplays the battery state of chargeonce its voltage is above 12.6V6.4 Special Instructions3.To obtain maximum output it is suggested that the panel’s direction is adjusted such that it faces the sun.4.Locate a clear sunlit area, free from overhanging branches, wires or obstructions to ensure maximumgeneration5.Broken modules cannot be repaired and contact with any module surface or frame can lead to electricalshock. Do NOT use a module with broken glass or torn substrate6.Do not disassemble the modules or remove any part of the module7.Do not drop Module or allow objects to fall on the Module. Do not stand or step on the Module8.Ensure the battery clamps/ connectors do not come in contact with one another to avoid short circuiting9.Ensure that all the electrical connections are secured before using the kit. Verify that the battery is beingcharged by the kit10.V erify the tightness of mechanical connections before using the kit11.P lease connect any type of load via the battery only7.TroubleshootingThe common problems are listed below. For any additional technical support, please get in touch with the local sales coordinator.1)PV Array Short CircuitIn case of array short circuit, check all the interconnections. In case of fault, immediately disconnect the faulty connection. Please take help of local sales coordinator if you find it difficult to repair the fault.2)Load Short CircuitCheck the continuity of fuse placed before battery. If blown, replace the faulty fuse and the faulty wire as necessary.3)Battery Reverse PolarityThe controller has protection against battery reverse polarity. It is however suggested to immediately correct the wiring to prevent any mishap.4)Overheating ProtectionIf the temperature of the controller heat sink exceeds 85 °C, the controller will automatically start overheating protection. However in case the system temperature rises, please keep in cool place such that its temperature drops before re-using it.5)High Voltage TransientsIf you are using this system in lightning prone areas, it is suggested that additional externalsuppression (such as using the system in range of lightening arrestor, etc.) is used.Question 1: Can the kit charge two or more 12 V batteries connected in parallel?Answer: Yes, it is possible if the batteries have the same type & capacity and are wired in parallel as a single 12V battery bank.Question 2: Is there any risk that the solar kit will over charge my battery?Answer: One of the functions of the solar charge controller is to ensure that your battery is not over charged. Question 3: Do I need to clean the solar panels?Answer: Yes, it is recommended for better performance. Dust and dirt should first be swept off the panel surface using a soft brush. When the sweeping is complete, use a wet cloth to wipe the panel surface to remove remaining dirt and/or stains.Question 4: Can I place my solar panels anywhere?Answer: To maximize generation, ensure that the tilt angle of system resembles the latitude of the place. If this is not possible, kindly ensure that the module is facing the sun and receives maximum irradiation. Further the solar module should not be operated under shadow.9.Limited WarrantyThe solar module of the kit has a 5 years of limited warranty and 10 years of power output warranty. The controller & rooftop box comes with a 1 year limited warranty. This warranty is valid against defects in materials and workmanship. It is not valid against defects resulting from, but not limited to:•Misuse and/or abuse, neglect or accident.•Improper installation, including but not limited to, improper environmental protection and improper hook-up•Damage in handling, including damage encountered during shipment or installation•Acts of God, including lightning, floods, earthquakes, fire, high winds, etc.•Exceeding the unit’s design limitNote:1.Warranty would stand void for module(s) whose type or serial numbers appears to be changed, erased,removed, illegible or in any manner altered or tampered.2.This warranty does not cover any cost associate with on-site labour and any cost associated with theinstallation, removal, reinstallation, shipping or transportation of the kit(s), any customs clearance or any other cost of return or re-shipment of kit(s).3.Any damages caused by abrasion, artificial damage or animals are exempt from this warranty.4.Defects and/or failures caused by unauthorized maintenance, operation or modification regardless ofwhether such act is wilful misconduct or negligence are exempted from warranty。
太阳能充电器说明书
太阳能充电器说明书规格参数太阳能输出: 5V/2400mA（阳光充足下）输入：5V/2A 输出：5V/3A（max）功能指示1 外接太阳能充电器并接输入端口2 太阳能充电指示灯3 USB输出端口4 大功率单晶硅太阳能板5 挂绳孔批准：审核：编制：产品简介· 本产品为户外便携式太阳能充电包，小巧玲珑，方便携带。
配备6片大功率的单晶硅太阳能板，高达 20％ 的转换率，输出电流高达2400mA, 为您的手机、IPAD或其他小设备充电。
在享受大自然阳光的同时为您提供源源不断的绿色能源，是您外出旅游出行的必备佳品。
为设备充电1、在有阳光的地方打开太阳能产品，使太阳能板接受太阳的45°照射，太阳能指示灯绿灯亮，这时USB输出可以输出高达5V/2.4A的电流为您的电子产品进行充电。
2、为获得更大的电流，此产品可以两个并联使用，并联后可以获得最大5V/3A的电流，实现快速充电。
温馨提示：本产品需要在阳光下使用。
本太阳能面板不能直接存储电源，如果您想存储电源，您可以使用它为移动电源充电。
如果产品不能工作，请检查 USB 接口是否正确插入太阳能面板。
工作后请记住，卸下USB插头。
12345User manualSpecification parameterSolar charging :5V/2400mA(In full sunshine)Input :5V/2AOutput :5V/3A （max ）批准：审核：编制：·Product introduction·The product is an outdoor portable solar chager, small and exquisite, easy to carry. Equipped with 6 high-power mono-crystalline silicon solar panels, high transmit efficiency 20%, up to 2400mA max charging current, It can charge mobile phone ，IPAD or other small mobile devices. It willprovide you with green energy while enjoying the natural sunshine ,which will be your travelnecessity.Charger the device1、Open the solar energy product in a place with sunlight, so that the solar panel receives 45° illumina-tion from the sun, the solar indicator is green, and the USB output can up to 5V/2.4A to charge your electronic products.2、For more current , It can be used in parallel for two or three products. After parallel ,the maximum current output : 5V/3A can be obtained to achieve fast charging.Tips: This product needs to be used in the sun. This solar panel cannot store power directly. If you want to store power, you can use it to charge mobile power. If the product does not work, check that the USB connector is properly inserted into the solar panel. Remember to remove the USB plug after work.Function indication1.External solar charger connected to the input port2.Solar charging indicatorB output port4.High power mono-crystalline silicone solar panelnyard hole12345。
太阳能智能充电控制器使用说明书
问题及处理方法 请检查光电池连线是否正确，接触是否可靠 系统超压，请检查蓄电池是否连接可靠，或是蓄电池电压过高； 蓄电池供电故障，请检测蓄电池连接是否正确 蓄电池过放，充足后自动恢复 负载功率超过额定功率，减少用电设备后，长按键一次恢复 负载短路，故障排除后，长按键一次或第二天自动恢复 请检查用电设备是否连接正确、可靠 请检查外接电源是否连接正确，＋，－极有无接反，电源有无供电 检测接线是否可靠,12V/24V 自动识别是否正确（针对自动识别的型号）
保护电路：
E 系列 □5A □10A □15A □20A □5A □10A □15A □20A □12V ； □24V ； □12V/24V Auto
<5mA； 不大于 0.20V； 不大于 0.20V； 17V；×2/24V； 14.6V；×2/24V (维持时间：30min)（当出现过放电时调用，或每 7 天调用一次） 14.4V；×2/24V (维持时间：30min) 13.6V；×2/24V (维持时间：直至降到充电返回电压动作) 13.2V；×2/24V 12.5V；×2/24V 12.0V；×2/24V 11.5V； ×2/24V 11.1V；×2/24V 12.0V；×2/24V 4mv/℃/2V（提升、直充、浮充、充电返回电压补偿）； 充电：PWM 脉宽调制； -35℃至+65℃； 1.25 倍额定电流 30 秒；1.5 倍额定电流 5 秒过载保护动作；≥3 倍额定电流短路保护。
solar power intelligent PV controller
Instruction book
Main features
1.
Intelligent control is realized by using microprocessor and dedicated control calculation.
TL-R-005 太阳能充电器 使用说明书V1.0
Copyright: Torch New Energy
Page 4
二、使用介绍
第1步：检查包装盒：观察包装盒是否完整？有无明显的压痕、破损等？ 如果有/可联系客服人员（货运商）。
盒子整体外观应该是完好、平整
Copyright: Torch New Energy
Page 5
第2步：打开包装盒：检查盒内物品是否完整？主要部件有以下2类： 充电器一套
第4步：充电器检查（给普通手机充电测试）：
输出转接线
选用合适的转接头
1、输出状态开关置于“通用”档，用配套的转接头给普通手机充电； 2、充电时间在2小时左右，具体时间和手机容量（原剩余电量）以
及当前充电器剩余电量有关系。
Copyright: Torch New Energy
Page 11
第5步：充电器检查（给I phone充电测试）：
主要组成部件 1、转接头：NOKIA 6101 / MOTOROLA V3 /
SAMSUNG A288 / SONY ERICSSON K750 /I phone 2、输入线、输出线、说明书
Copyright: Torch New Energy
Page 2
一、用途（优势）简介
1、 节能、低碳、环保； 2、电池大容量、给手机快速充电、兼容性强； 3、内置反向电流保护装置、防止电池过放、过充等；
输出转接线
输出转接线
1、 输出状态开关置于“苹果专用”档，用配套的转接头给I Phone充电； 2、充电时间在2-3小时左右，具体和手机容量（原剩余电量）以及当
前充电器剩余电量有关系。
Copyright: Torch New Energy
Page 12
第6步：充电器检查（太阳光充电测试）
AIMS POWER SCC10APWM 太阳能充电器安装和操作指南说明书
SCC10APWM Solar Charge Controller Installation and Operation Manual AIMS POWER9550 Gateway DrReno, NV 89521Tel:(775)359-6703Fax:(775)359-6753Email:******************************************READ MANUAL BEFORE USING THIS PRODUCT1. PRODUCT INTRODUCTIONThis AIMS Power PWM solar charge controller is designed to charge and monitor your LiFePO4 battery to achieve a longer life cycle. It also trickle charges AGM, GEL and lead acid battery technologies. Using the latest charging technologies combined with state of charge monitoring, this product allows for optimal battery maintenance and efficient solar power monitoring. The LCD screen displays operating modes such as; state of charge, voltage, and current. The product also displays symbols for easy user interface.Integrated data logger energy meterAutomatic detection of voltage 12 or 24 VdcPWM controlAutomatic load reconnectionListed to UL 1741 & CSA 22.2 No. 107.1Adjustable charge voltage2. INSTALLATIONInstall the charge controller near the battery on a stable surface. This surface should be solid, even, dry and nonflammable. The battery cable should be as short as possible and have a cable diameter size to minimize loss, e.g. 4 mm² at 20 A and 6ft in length (16 AWG).Do not install the controller in direct sunlight.To ensure adequate airflow around the controller, allow a 4 inch clearance around the unit. The temperature at the installation site may never fall below or exceed the maximum permitted ambient temperature range.Connect the individual components to the symbols provided on the bottom of controller.Follow the following connection sequence during installation:1. Connect the battery to the charge controller - positive and negative2. Connect the solar module to the charge controller - positive and negative3. Connect the DC load to the charge controller – positive and negative (optional)The reverse order applies when uninstalling.NOTE! The automatic detection of 12V or 24V systems functions properly only if this sequence order is followed. An improper sequence order can damage the battery!*There are no user serviceable parts inside the charge controller. Do not disassemble or attempt to repair the unit. Contact manufacturer. 3. OPERATION3.1 Description of LCD symbols3.2 Description of Button Function❶Button for switching display windows ❷ Enter/exit the setting (press for 5 seconds)❶Adjust parameters up ❷ Restore factory setting in each parameter (press for 5 seconds)❶Adjust parameters down (minus) ❷ Click this button to switch the load in main displaywindow3.3 View and Set the ParametersThe controller will auto display the “battery voltage” main display once power is connected (follow correct sequence from INSTALLATION instructions. This is the main display window. Use the buttonto switch between different display windows. If the parameter can be set, press the button(>5 seconds, numbers start flashing) to enter the setting, then press the or toselect the setting, after that, press the button (>5 secs) again to exit the setting (numbers stop flashing).Battery voltage(main display)Solar panelvoltageSolar panelcharging currentHigh voltagedisconnection(HVD)Float voltageAccumulative sum ofkwh drawn by loadAccumulative sumof recharged kwhLoad dischargingcurrentLow voltagereconnection(LVR)Low voltagedisconnection(LVD)Load workingmode3.3.1 Battery voltage (main display)Displays the battery voltage measured by the controller. Also, it displays thecharge and discharge status, battery capacity.3.3.2 The load ON/OFF controlIn the main display window, click the buttonto ON/OFF the load. The buttondoesn’t have this feature in the other interface.3.3.3 Environment temperatureDisplays the ambient temperature of the controller. C3.3.4 Solar panel voltageDisplays the solar panel voltage measured by the controller.3.3.5 Solar panel charging currentDisplays the charging current from the solar panel.3.3.6 Load discharging currentDisplays the discharging current drawn by load.3.3.7 Accumulative sum of recharged AhDisplays the accumulative sum of recharged Ah from solar panel. Press the button for 5 seconds to reset the meter to 0. Even when the battery isdisconnected the value remains. When 9999Ah are reached, it will switch backto 0 Ah.3.3.8 DC load consumptionDisplays the accumulative sum of Ah drawn by the DC load. Press the button for 5 seconds to reset the meter to 0. Even whenbattery is disconnected the value remains. When 9999Ah are reached, it willswitch back to 0 Ah.3.3.9 High voltage disconnection (HVD) Float voltage - ADJUSTABLE Displays the float voltage, when battery voltage reaches float voltage, the controller will start PWM control to keep the battery voltage at same level. Press the button (>5 seconds, numbers start flashing) to enter thesetting, then press theorto select the setting. Press the buttonagain to exit the setting (numbers stop flashing).3.3.10 Low voltage reconnection (LVR) - ADJUSTABLEDisplays the values for the LVR voltage. Under the LVD protection in the controller, when battery voltage is restored to higher voltage than LVR voltage, the controller will re-connect the load circuit. Press the button (>5 seconds, numbers start flashing) to enter thesetting, then press theorto select the setting. Press the buttonagain to exit the setting (numbers stop flashing).3.3.12 DC Load operating mode - ADJUSTABLEAs shown on the right, it displays the load operating mode. Different values represent different working modes.24h - normal mode, there is always output unless the battery voltage is too low.1-23h - light control with time control mode. Load will turn on after dusk and turn off according to the timer setting.0h - light control mode, load will turn on after dusk and turn on before dawn.Press on the button(>5 seconds, numbers start flashing) to enter thesetting, then press theor to select the setting. Press the buttonagain (>5 secs) to exit the setting (numbers stop flashing).4. COMMON FAULT AND HANDLING4.1 LVD Protection resolutionScreen display as shown in the figure that the battery drops below the LVD protection voltage. The controller has entered the LCD protection state, load circuit has been disconnected. Use the solar panels to recharge the battery or charger when the battery voltage reaches LVR voltage, the controller will resume the load power supply after battery reaches normal working state.4.2 Over load Protection fault resolutionScreen display (see the figure) and flashing shows over load circuit current For 60 seconds at more than 1.5 times the rated current.Overload protection state. After reducing the load, press the buttonto restore power to the load.4.3 Short Circuit Protection fault resolutionScreen display (see the figure on the right) and flashing shows there is a short circuit on the load circuit. The controller has entered into Short Circuit Protection State. Check the load for damage to the wiring circuit.After troubleshooting and correcting short circuit quick press buttonto enable the load.4.4 Solar Panel Fault resolutionSymbol flashing indicates that the controller has not detected the solar panels within 24hours. Check connection from solar panel to charge controller. Also, check if there is an open circuit between solar panel with controller. 4.5 Load Shock Fault Open load if theflashing, this indicate the load current is more than twice rated current of thecontroller. This will cause the controller to reset several times.5. WARRANTYAIMS Power offers a 2 year limited warranty.The following cases are not covered under warranty.1. DC reverse polarityThe charger is NOT designed with DC reverse polarity protection. A reverse polarity may severely damage the inverter.2. Incorrect DC wiring3. Operation in a moist environmentAIMS Power Warranty Instructions:This product is designed using the most modern digital technology and under very strict quality control and testing guide lines.If,howeveryoufeelthisproductisnotperformingasitshould,pleasecontactus:**************************(775)359-6703.We will do our best to resolve your concerns. If the product needs repair or replacement, make sure to keep your receipt/invoice, as that will need to be sent back along with the package and RA# prepaid to AIMS. You have a limited 2 year from date of purchase warranty.This warranty is valid worldwide with the exception that freight and duty charges incurred outside the contiguous 48 United States will be prepaid by customer.Except as provided above, AIMS makes no warranty of any kind, express or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose. In no event shall AIMS be liable for indirect, special or consequential damages. This warranty only applies to AIMS Power branded products. All other name brand products are warranted by and according to their respective manufacturer. Please do not attempt to return non-AIMS Power branded products to AIMS Power.For additional products such as:- Modified sine wave inverters- Pure sine wave inverters- Solar charge controllers- Generators- Inverter chargers with automatic transfer switches- Custom cut cables- Batteries- Solar panelsPlease visit our web site: Tofindoutwheretobuyanyofourproducts,youmayalsoe-mail:************************(775)359-6703.6. TECHNICAL DATASHEETModelSCC10A PWMRated current10ARated voltage 12/24VMax solar voltage<50V(12/24V) Low voltage disconnect 10.7/21.4V Low voltage reconnect 12.6/25.2V Float charge 13.7/27.4V Standby loss <30mA Material ABS+AluminumUSB output 5V/2A Charging mode PWM Temp compensation -4mV/Cell/℃ Operating condition-20℃ to 60℃ | -4°F to 140°F Size/Weight6.5L”* 3.5W”* 1.5H”.5 lb。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
太阳能充电器使用说明书本产品是一款多功能太阳能应急充电器，内置1200mAh高容量可充电锂电池，可随时随地对您的手机、数码相机、PDA、MP3、MP4等数码产品进行充电。
造型华贵大方，小巧玲珑，携带方便，时尚高雅。
使用方法1、使用之前请给您的太阳能充电器充电，有三种方法可以选择：a、将充电器放置于太阳光直射处，太阳能将转化为电能给充电器内置可充电电池充电。
b、将充电器USB线连接电脑，此时充电器指示灯会闪光，表示正在充电，当充电满后，此灯将会熄灭。
C、用交流适配器充电，充电时指示灯会闪光，当充电满后此灯将会熄灭（因为设计有自动断电保护）2、将转换接头连接到延长线，再将延长线的另一头连接到充电器，或直接将转接头连接到充电器。
3、将转换接头连接到您的手机或其它数码产品。
4、从您的手机或其它数码产品上将可看到正在充电，充电的同时您也可以用手机通话。
5、太阳能充电指示。
将开关拨到‘NO’，太阳能板在接受阳光照射时，太阳能充电指示呈绿色。
产品特点：1、特别适用于应急场合。
当您在野外作业或旅游，或者遇到停电时，太阳能充电器将会帮您的大忙，使您的手机随时随地保持工作状态，让您不间断的与您的朋友和家人保持联系。
2、使用方便无论何时何地，您都可以极为方便的给您的手机或其它数码产品充电。
3、高效率充电给您的手机充电60分钟，可以获得100-150分钟通话时间4、环保、节约能源使用绿色能源太阳能，可为环保作出您的贡献。
5、外形时尚，携带方便造型简洁华贵，超薄不锈钢外壳设计，小巧玲珑，携带方便。
6、使用安全带有充电过充保护，有效延长您的手机电池的使用寿命，使用安全。
产品规格1、使用高转换效单晶硅或多晶硅片，太阳能转换效率高达15%以上。
2、太阳能电池板规格：5.5V/80mA。
3、充电时内置高容量可充电锂电池：1200 mAh。
4、输出电压：5.5V。
5、输出电流：1000mA。
6、充电器给手机充电时间：约60分钟（不同品牌和型号的手机有少许差别）。
7、太阳能给充电器内置电池充电时间：10-15小时。
8、用电脑或交流适配器给充电器内置电池充电时间：约5小时。
本产品适用于下列产品充电*手机（标准配置有诺基亚，三星，摩托罗拉，索爱，迷你USB五种转接头）*数码相机*PDA*MP3*MP4（内置可充电电池容量须小于1200mAh）。
注意事项1、请不要用尖锐物体刮擦太阳能电池板表面。
2、用太阳能给充电器内置可充电电池充电时，请将太阳能板朝上置于阳光直射处，以保证最佳充电效果。
3、请不要长时间用电脑或交流适配器给充电器内置可充电电池充电，当充电指示灯常亮时请尽快停止充电。
4、请不要用其它AC适配器给太阳能充电器充电。
5、请不要在下雨天将充电器置于户外。
6、如因短路保护，仅需拔掉短路负载，10秒钟既可恢复供电。
SOLAR CHARGER USER’S MANUALThis product is a multi-functional solar emergency charger,Build in 1350mAh high capacity rechar geable polymer battery,you can charge your mobile phone,digital camera,PDA,Mp3,Mp4 whenever and wherever,Style design and convenient to take it with you .HOW ITWORKSPlease follow these steps:1.charge your solar energy emergency charger gefore use ,there are 3 method.a.put the charger under the sunshing ,the solar energy will convert to electrical energ and charge the build in rechargeable battery.b.connect the charger to your computer with USB cable,the charge indicator will be flasshing, when the battery is full ,the indicator will be tm off.c.charge it with Acadapter,the charge indicator will be flahing,when the battery is full,the indicator will be tum off,2.connect your connector adapter to the extended cable and then connect to the charger,3.connect your phone or other digital products to the connector,4.your phone or other digital products indicates that it is charging ,now you can use your mobile phone while charging5.solar energy charging indicatorswitch “on”when the solar energy board receiving the sun light,the charging indicating light tums purple,and then it can be used as money detector.PRODUCT PERFORMANCE1.Meet an emergencyWhen you go to outside or powercut,you also can use your mobile phone with solar energy.2.conceniencewhenever and wherever you are ,you can charge your mobile phone in time,and you could talk withothers when charging.3.High efficiencyCharging 60minutes,the charger could transfer the energy from the build in battery to your mobile phone battery,and could talking 100-150minutes.4.Environment protect,save resourceYou can use solar energy to charge your mobile phone wherever and whenever,5.Modem and portableModem dem design,stainless steel case ,small size,convenint to take it with you6.Safe useOver voltage protection for the circuitand your mobile phone.smart charge,sate usePRODUCT CHARACTERISTIC1.High solar energy convert efficiency:over than 15%.2.solar energy board:5.5v/80mA3.gigh capacity build in polymer battery:1350mAh4.output voltage:5.5v5.output current:1000mA6.charging time:about60minutes(the time is a little different for different mobile phone)7.to charge the build in battery in the charger using computer or AC adaper: about 5 hours FITS FOR*mobile phone (standard accessory are five kinds of phone connetor adaptor,NOKIA,SAMSUNG, MOTOROLA,SONY-ERICSSION,MiniUSB)*digital camera*PDA*MP3*MP4(the battery capacity under 1200MAH)ANNOUNCEMENT1.Don’t scrpe the srface of the solar energy board with sharpobject.2.please put your charger under the sunshine directly and the solar board side is uptumed if youchargeit with solar energy.3.don’t t charge the build in battery in your charger for too long time if you charge it withcomputer or AC adapter.4.don’t use other AC adatper to charge the solar charger.5.don’t put your charger in the rain.6.in case of short circuit protection,all you need to do is unplug short-circuit plus load, afterwhich power supply will resume in 10seconds.。