最新工厂专业英语术语
工厂专业英语术语
工厂专业英语术语Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OO BA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板b arcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource departmen t 人力资源部production department生产部门planning department企划部QC Secti on品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thicknes s gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die butto n圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopp er清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizat ion去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料deg rease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer 备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting m achine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine 亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grai n细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenchi ng淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。
（工厂管理）工厂术语（英语）
（工厂管理）工厂术语（英语）CORPORATE COMMON ABBREVIATION常用语缩写1 Organization组织1-1 HQ Head Quarter 总公司1-2Chairmen主席1-3Lite-On Group光宝集团1-4 President 总裁1-5Executive Vice President 常务副总裁1-6Vice President副总裁1-7HR Human Resource人力资源部1-8FIN Finance 财务1-9Sales 销售1-10R&D Research & Developing 研发部1-11QA 质量保证QA DQA CS1-12MIS Management Information System资讯管理系统1-13Pur 采购Purchasing1-14IMD Image management division 影像管理事业部1-15ITS information technology system 计算机部1-16QRA quality reliability assurance 品保部1-17MFG manufacturing 制造部1-18PMC production &material control 生(产)物(料)管(理) 1-19 PRO Procuremnet 采购开发部1-20 PMO Plant Manager Office 厂长室1-21 CEO Chief Executive Officer 执行总裁2 Materials 材料2-1PC Production Control 生产控制2-1-1MPS Mass Production Schedule 量产计划2-1-2FGI Finished goods Inventory 成品存货2-1-3UTS Units To Stock存货单元2-1-4WIP Working In Process Inventory在制品2-1-5C/T Cycle Time 循环时间,瓶颈2-1-6WD Working Days 工作天2-1-7MTD Month To Days 月初到今日(例如总表整理)2-1-8YTD Year To Days 年初到今日2-1-9 SO Sales Order 销售单2-1-10MO Manufacture Order 制造单2-1-11 BTO Build T o Order 订单生产2-1-12 P/N part number 料号2-1-13 FCST Forecast 预测计划2-1-14 W/O Working Order 工单2-1-15 P/O Purchasing Order 采购单2-1-16 VDS Vendor Delivery Schedule 厂商送货进度表2-1-17 D/C Delivery Order 交货单2-2 MC Material Control材料控制2-2-1 MRP Material Requisition plan 材料申请计划2-2-2 INV Inventory 存货清单; Invoice 发票2-2-3 Inv Turn Over Days=INV$/NSB X WD 库存周转天数2-2-4 PSI Production Shipping Inventory 预备待出货2-2-5 JIT Just In Time 实时，准时制、零库存2-2-6 Safety Inventory 安全存量2-2-7 CKD Completed Kits Delivery全件组装出货2-2-8 SKD Semi Kits Delivery半件(小件)组装出货2-3 W/H Warehouse 仓库2-3-1 Rec Receiving Center 接收中心2-3-2 Raw MTL 原物料2-3-3 F/G finish goods 成品2-3-4 GRN Goods Received Note 货物接收单2-4 Import/Export进出口2-4-1 SI Shipping Instruction发货指令2-4-2 PL Packing List包装清单2-4-3 Inv Shipping Invoice出货发票2-4-4 ETD Estimated Time of Departure 预估离开时间2-4-5 ETA Estimated Time of Arrive 预估到达时间2-4-6 BL Bill of Landing 提货单（海运）2-4-7 AWB Air Way Bill 提货单（空运）2-4-8 MAWA Master Air Way Bill主提货单2-4-9 HAWB House Air Way Bill副提货单2-4-10 TEU Twenty foot Equipment Unit(Contain)二十英尺货柜2-4-11 FEU Forty foot Equipment Unit(Contain)四十英尺货柜2-4-12 CY Container Yard货柜场2-4-13 THC Terminal Handing Charge 码头费2-4-14 ORC Original Receiving Charge码头费2-5 PUR Purchasing采购2-5-1 FOB Free on Board货运至甲板2-5-2 CIF Cost Insurance Freight2-5-3 OA Open Account 开户2-5-4 TT Telegram Transfer电汇2-5-5 COD Cash On Delivery 现金支付2-5-6 CRP Cost Reduction Program降低成本方案2-5-7 PR Purchasing Requisition采购申请2-5-8 PO Purchasing Order采购单2-5-9 LT Lead Time 交期2-5-10 LLT Long Lead Time 长时间交期2-5-11 Payment term 付款条件2-5-12 Debit note 扣款2-5-13 CRP Cost Reduction Program 降价计划2-5-14 Quotation 报价3 MFG Manufacturing Production制造控制3-1 DL Director Labor直接人工3-2 IDL Indirect Labor间接人工3-3 DLH Direct Labor Hours直接工时3-4 Productivity=UTS/DLH3-5 PPH Pieces Per Hour每小时件数3-6 Efficiency=Actual/T arget(%)3-7 DT Machine Down Time停机时间3-8 AI Auto Insertion自动插入3-9 MI Manual Insertion人工插入3-10 SMD Surface Mount Device表面粘着零件SMT Surface mount technology 表面粘着技术3-11 B/I Burn In (for how many hours at how many degree)烧机3-12 Equipment Utilization3-13 WI work instruction 工作说明3-14 SOP standard operation procedure作业指导书3-15 R/I run in 运转机器3-16 ESD electrical static discharge 静电释放3-17 MP mass production 量产3-18 EMC Electro Magnetic Compatibility, 电磁兼容性3-19 EMI Electro Magnetic Interference, 电磁干扰3-19 SIR Surface Impedance Resistance 表面阻抗测试4 Engineer工程4-1 PE Products Engineer; 产品工程Process engineer制程工程4-2 TE Test Engineer测试工程4-3 ME Manufacturing Engineer;制造工程Mechanical Engineer机械工程4-4 IE Industrial Engineer工业工程4-5 DCC Document Control Center文管中心4-6 BOM Bill Of Material材料清单4-7 ECN Engineering Change Notice工程变动公告4-8 TECN Temporary Engineering Change Notice工程临时变动公告4-9 ATY Assembly Test Yield Total Yield直通率4-10 TPM Total Productivity Maintenance全面生产维护4-11 PM product manager ;project manager 产品经理;项目经理4-12 ECR engineering change request 工程变更申请4-13 ECO engineering change order 工程变更指令4-14 EN engineering notice 工程通告4-15 WPS work procedure sheet 作业说明书4-16 ICT in circuit test 电路测试4-17 P/R pilot run ;C/R control run; T/R trial run试做4-18 EVT engineer verification test工程验证测试4-19 DVT design verification test 设计验证测试4-20 MVT multi-verification test 多项验证测试4-21 ORT on going reliability test 出货信赖性测试4-22 S/W software 软件4-23 H/W hardware 硬件4-24 EAR Engineering Aanlysis Request 工程分析需求4-25 ECE Engineering Change Estimation 工程变更评估4-26 ECC Engineering Change Cancellation 工程变更取消4-27 IEM Internal Engineering Meno 内部工程备忘录4-28 PAS Part Approval Sheet 零件承认书4-29 DAB Daily Action Boaed 日常工作广告牌4-30 TMR Tooling Modify Report 修模协议书4-31 CRT Control Run Testing 试产测试4-32 DCD Design Change Description 设计变更通知4-33 ESR Engineering Study Report 工程研究报告4-34 EI Engineering Information 工程讯息4-35 PMP Process Management Plan 制程管制计划4-36 MBO Management By Object 目标管理4-37 KPI Key Performance Indicator 重点绩效指标4-38 PIP Part Inspection Plan 零件检验标准4-39 CTF Criticle T o Function 功能重点尺寸4-40 CTA Criticle T o Assembly 组装重点尺寸4-41 R&D Research and Development 研究与开发4-42 GR&R Gauge Repeatability and Reproducibility 治具重复性及重现性验证4-43 Cpk 制程能力指标4-44 FAI First Article Inspection 首件检查表5 QA Quality Assurance质量保证QRA Quality & Reliability Assurance质量与可靠性保证5-1 MQA Manufacturing Quality Assurance制造质量保证5-2 DQA Design Quality Assurance设计质量保证5-3 QC Quality Control质量控制5-4 IQC Incoming Quality Control进货质量控制5-5 VQC Vendor Quality Control售货质量控制5-6 IPQC In Process Quality Control制程质量控制5-7 OQA Out going Quality Control 出货质量控制5-8 QE Quality Engineer质量工程5-9 AQL Acceptable Quality Level可接受的质量水平5-10 DPPM Defective Pieces Per Million units百万件中有损件数5-11 PPM Pieces Per million百万分之一5-12 CS Custom Service顾客服务5-13 MRB Material Review Board 材料审核委员会5-14 DMR Defective Material Report材料缺陷报告5-15 RMA Return Material Administration材料回收处理5-16 Life Test 寿命测试5-17 T/C Temperature Cycle温度循环5-18 H/T High Temperature Test高温测试5-19 L/T Low Temperature Test低温测试5-20 ISO International Standard Organization国际标准化组识5-21 SPC Statistic process control统计过程控制5-22 "5S" 整理.整顿.清理.清扫.素养5-23 VMI visual mechanical inspection 外观机构检验5-24 MIL-STD military standard 美军标准5-25 SPEC specification 规格5-26 AVL approval vendor list 合格厂商名单5-27 QVL qualified vendor list 合格厂商名单5-28 FQC final quality control 最终质量控制5-29 OBA open box audit 成品检验5-30 EAR engineering analysis request 工程分析需求5-31 FAI first aide inspection 首件检验5-32 VQM vendor quality management 厂商质量管理5-33 CAR corrective action request 改进对策要求5-34 4M man; machine; material; method 人、机、材、方法5-35 M man;machine;material;method;measurement 人、机、材、方法测量5-36 MTBF mean time between failure平均寿命5-37 TTL total 总量5-38 MRT Markeing Relability Testing 信赖性测试5-39 8 D 8 Disciplines5-40 Q7 Method (Stratification: Histogram; Pareto; Scatter; (Cause & effect diagram) Fish Bone; (Check sheets); (Graphs & Control Chart)5-41 6 Sigma5-42 3 W What, Who, When5-43 2 Q Quality and Quantity5-44 1 G 1 Goal 一个目标6 FIN Finance &Accounting财务与帐目6-1 P&L Profit &Lose6-2 PV Performance Variance现象差异6-3 3 Element of Cost=M,L,O6-4 M Material材料6-5 L Labor人力6-6 O Overhead管理费用6-7 Fix OH Fixed Overhead固定管理费用6-8 Var OH Variable Overhead不定管理费用6-9 COGS Cost Of Goods Sold工厂制造成本6-10 AR Account Receivable应收6-11 AP Account Payable应支7 MIS Management Information System资讯管理系统7-1 IS Information System资讯系统7-2 IT Information Technology 信息技术、资讯技术7-3 MRP Material Requisition Plan材料需求计划7-4 I2 Information Integration System资讯整合系统7-5 SAP System Application Programming系统申请项目7-6 ERP Enterprise Resource Programming企业资源项目8 HR Human Resource人力资源8-1 PR Public relation公共关系8-2 T/O Turn Over Rate =Monthly T/O Total People*12 8-3 GR General Affair总务。
工厂专业英语术语
工厂专业英语术语Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet g un拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OOBA 开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板barcod e条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosm etic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section 品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equ ipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤d ents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness g auge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam b lock滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button 圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper 清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizati on去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrea se脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting mac hine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=i nteraction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain 细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液cr usher破碎机。
电子工厂专业英语词汇
电子工厂专业英语词汇公司标准化编码 [QQX96QT-XQQB89Q8-NQQJ6Q8-MQM9N]、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条形码barcode scanner条形码扫描仪fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝镑、英寸EMI gasket导电条front plate前板rear plate后板chassis |'∫si| 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接柆键sheet metal parts 冲件plastic parts塑料件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车Personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager |'depjuti| =vicemanager副理section supervisor课长deputy section supervisor =vicesection supervisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturingprocedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embeded lump|in'bed| |lmp|镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzer蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴industrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vacuum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a littlebigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead / slipperyscrew head螺丝滑头slipped screwhead / shipperyscrew thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excessive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of packaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterpriseexpansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board广告牌feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualified, up to grade合格not up to grade, not qualified 不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---tothrow--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, riveting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊Vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece,block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货To return/delivery to. to senddelivery back to return ofgoods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cut edges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line stretching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder活页夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerization装箱quantity of physical inventorysecond count 复盘点数量Quantity of customs count会计师盘,点数量the first page第一联filed by accounting departmentfor reference会计部存查end-user/using unit(department)使用单位Summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physicalinventory list will be sent toaccounting department together(Those of NHK will be sent tofinancial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventoryList and physical inventorycard 年终盘点卡与清册使用－状况明细表Blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering moldtesting工程试模材料not included in physicalinventory不列入盘点sample样品incoming material to beinspected进货待验description品名steel/rolled steel钢材Material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by /prepared by核准/审核/承办PCE assembly productionschedule sheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation 生产确认checked by初审approved by核准department部门Stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明Year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventorylist备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码flow chart流程窗体assembly组装stamping冲压molding成型spare parts=buffer备品coordinate坐标dismantle the die折模auxiliary function辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕疪shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blister气泡fillet镶;嵌边through-hole form通孔形式roller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴angular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing block衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleeve套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口submarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣质量人员名称类QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 质量工程人员质量保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供货商质量评估OOBA out of box audit 开箱检查QFD quality function deployment 质量机能展开FMEA failure model effectiveness analysis 失效模式分析8D 8 disciplines 8项回复内容FA final audit 最后一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收质量水平S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂质量AOQL Average Output Quality Level 平均出厂质量Q/R/S Quality/Reliability/Service 质量/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水平等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理R Range 全距AR Average Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility & Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它质量术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 质量改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 质量改善QP Quality Policy 目标方针TQM Total Quality Management 全面质量管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低质量水平RMA Return Material Audit 退料认可QAN Quality Ameliorate Notice 质量改善活动ADM Absolute Dimension Measurement 全尺寸测量QT Quality Target 质量目标7QCTools 7 Quality Control Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供货商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 质量系统ES Engineering Standardization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manufacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 质量工程(部) QA Quality Assurance 质量保证(处) QC Quality Control 质量管理(课) PD Product Department 生产部LAB Library 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Assembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等) PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供货商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设PC Personal Computer 个人计算机CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆the United States of America 美国As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光盘CD-ROM Compact Disk Read-Only Memory 只读光盘FDD Floppy Disk Drive 软盘机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算器辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requirement 周出货需求CT Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间) S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略质量保证DQA Design Quality Assurance 设计质量保证MQA Manufacture Quality Assurance 制造质量保证SSQA Sales and service Quality Assurance 销售及服务质量保证LRR Lot Reject Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnet Inspect 高磁测试FMI Frequency Modulated Inspect 高频测试B/M Boar/Molding (flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Advanced Basic in put/output system 先进的基本输入/输出系统CMOS Complementary Metal-Oxide-Semiconductor Transistor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectiveness 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Cable 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requirement Planning 物料需计划OS Operation System 操作系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size。
工厂常见英语术语及略缩语
1. Sales Department:Assembly line 组装线Layout 布置图- Sales order 销售定单Conveyer 流水线物料板- Sales order release form 生产通知单Rivet table 拉钉机- sales rolling forecast (滚动式)销售预测Rivet gun 拉钉枪- bit tender 投标Screw driver 起子- contract terms 合同条款Pneumatic screw driver 气动起子- payment terms 付款方式worktable 工作桌- product specification 产品规格OOBA 开箱检查- delivery schedule 交期fit together 组装在一起- on time delivery 准时交货fasten 锁紧(螺丝)- short order 缺货fixture 夹具(治具)- build to stock 按库存排生产pallet 栈板- build to order 以销定产barcode 条码- contract amendment 合同修订barcode scanner 条码扫描器- order confirmation 合同确认fuse together 熔合- sales officer 销售员fuse machine热熔机repair修理2. PMC (Purchasing & Material Control)operator作业员QC品管- Purchase requisition 采购申请supervisor 课长- Purchasing order 采购定单ME 制造工程师- Supplier 供应商MT 制造生技- Vendor/buyer 卖主cosmetic inspect 外观检查- Subcontractor 分承包商inner parts inspect 内部检查- Supplier evaluation 供应商评审thumb screw 大头螺丝- Buyer 买家lbs. inch 镑、英寸- Stock level 库存量EMI gasket 导电条- Stock register 库存记录front plate 前板- Material released request 物料发货单rear plate 后板- Product released request 产品发货单chassis 基座- Lead time (for purchase order) 交期bezel panel 面板#NAME?power button 电源按键- (products) over due of the shelf life 过期reset button 重置键- Re-order point 再采购期Hi-pot test of SPS 高源高压测试- Safety stock/Safety stock level 安全库存/安全库存量Voltage switch of SPS 电源电压接拉键- Cycle time 库存周转期sheet metal parts 冲件- Storage condition plastic parts 塑胶件- Store Reeper 仓管员SOP 制造作业程序material check list 物料检查表3. Production work cell 工作间trolley 台车- production planning 采购计划carton 纸箱- product specification 产品规格/标准sub-line 支线- processing specification 过程控制程序left fork 叉车- product cycle time 生产周期personnel resource department 人力资源部- standard time 工时定额production department生产部门- production capacity 产能planning department企划部- production volume 产量QC Section品管科- machine utilization 机器正常运转率stamping factory冲压厂- machine down time 停机率painting factory烤漆厂- operating condition 生产操作molding factory成型厂- Humidity 湿度common equipment常用设备- Moisture level 湿度率uncoiler and straightener整平机- Dust level 尘埃水平punching machine 冲床- Dust count 尘量robot机械手- Formula (物料)配方hydraulic machine油压机- proportion of the ingredients 配料比例lathe车床- bill of materials 物料清单planer |plein|刨床- control standard 控制指标miller铣床- control parameter 控制参数grinder磨床- upper control limit 上限linear cutting线切割- lower control limit 下限electrical sparkle电火花- tolerance 误差值welder电焊机- variation 被动值staker=reviting machine铆合机- process capability and stability 过程能力/稳定性position职务- first article or last article inspection 首件检测president董事长- confirmation of process 工序过程确认general manager总经理- process flow 流程special assistant manager特助- process flow chart 流程图factory director厂长- traveller card 随机卡department director部长- tag 标牌deputy manager | =vice manager副理- transit store 周转仓section supervisor课长- product & process identification 产品/过程标识deputy section supervisor =vice section superisor副课长- traceability 追溯性group leader/supervisor组长- Production line 生产线line supervisor线长- operator/supervisor 操作工/领班assistant manager助理- normal operating condition 正常操作条件to move, to carry, to handle搬运- shift 班次be put in storage入库- passed for inspection 通过检验pack packing包装- acceptance /rejection rate 合格/不合格率to apply oil擦油- rejected and accepted products 不合格/合格产品to file burr 锉毛刺- failure to meet the requirement 未达到要求final inspection终检- the control standard should be…. but was found to be….控制指标应为…实际为…to connect material接料- production yield 生产完工率to reverse material 翻料- temperature profile 湿度曲线wet station沾湿台- under control condition 受控条件下Tiana天那水- out of control 超标cleaning cloth抹布- regular processing monitoring 定期工序监控to load material上料to unload material卸料4. Quality control to return material/stock to退料scraped |'skr?pid|报废- IQC scrape ..v.刮;削- incoming inspection 进料检验deficient purchase来料不良- sampling plan 抽样计划/抽样方案manufacture procedure制程- sample size 抽样量deficient manufacturing procedure制程不良- sampling method 抽样方法oxidation |' ksi'dei?n|氧化- acceptable quality level 允收标准(仅针对抽样检验)scratch刮伤- inspection instruction 检验指导书dents压痕- visual inspection 外观检验defective upsiding down抽芽不良- defect 缺陷defective to staking铆合不良- scratch 划痕/划伤embedded lump镶块- burs 毛刺/毛边feeding is not in place送料不到位- product sample 产品样stamping-missing漏冲- crack 裂缝production capacity生产力- void 空缺处education and training教育与训练- dimensional measurement 尺寸测量/尺寸检查proposal improvement提案改善- testing 测试spare parts=buffer备件- testing parameter 测试参数forklift叉车- drop test 跌落试验trailer=long vehicle拖板车- tensile strength/tensile strength 张力强度/拉力强度compound die合模- elongation test/elongation rate 拉伸测试/拉伸率die locker锁模器- high pot test 高压(电压)测试pressure plate=plate pinch压板- burning test 烧机bolt螺栓- reliability test 可靠性试验administration/general affairs dept总务部- test rejection 拒收automatic screwdriver电动启子- pending for disposition 等待处理thickness gauge厚薄规- waiting for inspection 等待检验gauge(or jig)治具- disposition of rejected products 拒收产品的处理power wire电源线- out of specification 超标buzzle蜂鸣器- rework 返工defective product label不良标签- waive 放弃/报废identifying sheet list标示单- waive inspection 免检location地点- compulsory test items 强制检验/测试项目present members出席人员subject主题indication 缺陷conclusion结论service 保养，维护，维修decision items决议事项field 现场 in the field responsible department负责单位rounded indication 点状缺陷pre-fixed finishing date预定完成日solvent 溶剂approved by / checked by / prepared by核准/审核/承办layout 划线PCE assembly production schedule sheet PCE组装厂生产排配表finish 粗糙度model机锺flatness 不平度work order工令bearing housing 轴承箱revision版次dial indicator 千分表remark备注laser topography 激光测量production control confirmation生产确认environmental regulation 环境法checked by初审burr 毛刺approved by核准localized pitting 部分点蚀department部门etch 腐蚀stock age analysis sheet 库存货龄分析表crack 裂纹on-hand inventory现有库存shrinkage 缩孔available material良品可使用peening 锤击obsolete material良品已呆滞Engineering’s 技术部门to be inspected or reworked 待验或重工shielded carbon arc welding 碳弧保护焊, 气体保护碳极电弧焊total合计emissivity paint 辐射涂料cause description原因说明rest 支架part number/ P/N 料号thermocouple 热电偶type形态truth spot （工件上的）检验点item/group/class类别thermal treatment 热处理quality品质stress relief 应力释放prepared by制表 notes说明mechanical testing 机械性能试验year-end physical inventory difference analysis sheet 年终盘点差异分析表index 分度physical inventory盘点数量test specimen 试样physical count quantity帐面数量thermal stability test 热稳定试验difference quantity差异量reading 读数cause analysis原因分析forging 锻件raw materials原料casting 铸件materials物料deflection 挠度finished product成品plating 电镀semi-finished product半成品chromium plating 镀铬packing materials包材wear 磨损good product/accepted goods/ accepted parts/good parts良品luster 光泽度defective product/non-good parts不良品magnetic particle examination 磁粉探伤disposed goods处理品dry visible magnetic particle examination 干法非荧光磁粉探伤warehouse/hub仓库wet fluorescent magnetic particle examination 湿法荧光探伤on way location在途仓blazing 钎焊oversea location海外仓induction blazing 感应钎焊spare parts physical inventory list备品盘点清单Stellite 硬质合金spare molds location模具备品仓nitric acid 销酸skid/pallet栈板radiographic examination 射线探伤tox machine自铆机liquid penetrant examination 液体渗透探伤wire EDM线割ultrasonic examination 超声波探伤EDM放电机shot peening 喷丸coil stock卷料packing piece, packing section, caulking piece,caulking section填隙条sheet stock片料clearance fit 间隙配合tolerance工差interference fit 过盈配合score=groove压线descaling 除锈cam block滑块coating 涂层，覆层，镀层pilot导正筒cold drawing 冷拉（件）trim剪外边shot blasting 喷丸（处理）pierce剪内边grit blasting 喷钢砂（处理）drag form压锻差sand blasting 喷砂（处理）pocket for the punch head挂钩槽bar 棒材slug hole废料孔stock 原料feature die公母模lubricant 润滑剂expansion dwg展开图rolling mill，roll machine 轧钢厂，轧钢机，滚轧机radius半径draw benche 拉床shim(wedge)楔子gas fired furnace 煤气加热炉torch-flame cut火焰切割shear machine 剪切机set screw止付螺丝straightening roll machine 辊式矫直机form block折刀decarburization 脱碳stop pin定位销Charpy impact text 夏比冲击试验round pierce punch=die button圆冲子fatigue 疲劳shape punch=die insert异形子die 模具stock locater block定位块tensile testing 拉伸试验under cut=scrap chopper清角solution 固溶处理active plate活动板aging 时效处理baffle plate挡块cold header冷墩机cover plate盖板grub screw 平头螺钉]male die公模elongation 延伸率female die母模rivet 铆钉groove punch压线冲子groove 槽air-cushion eject-rod气垫顶杆Rockwell hardness 洛低硬度spring-box eject-plate弹簧箱顶板Brinell hardness 布氏硬度bushing block衬套ferrite 铁素体insert 入块stand 架子club car高尔夫球车sheeter 轧板机capability能力roll 辊子parameter参数convex 凸状,凸面factor系数concave 凹, 凹面，凹板phosphate皮膜化成guide board 导板viscosity涂料粘度pitch gauge 螺距规alkalidipping脱脂guillotine shear 剪板机main manifold主集流脉descale 除污，除氧化皮等。
工厂专业英语术语
工厂专业英语术语Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机repair修理 operator操作人员 QC品管 supervisor 科长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条front plate前板 rear plate后板 chassis 基座 bezel panel面板power button电源按键 reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑料件 SOP制造作业程序 material check list物料检查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备uncoiler and straightener整平机punching machine 冲床 robot机械手 hydraulic machine油压机lathe车床 planer |'plein?|刨床 miller铣床 grinder磨床linear cutting线切割 electrical sparkle电火花 welder电焊机staker=reviting machine铆合机 position职务 president董事长general manager总经理special assistant manager特助factory director厂长 department director部长deputy manager | =vice manager副经理 section supervisor科长deputy section supervisor =vice section superisor副科长group leader/supervisor组长 line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库 pack packing包装to apply oil擦油to file burr 锉毛刺 final inspection终检to connect material接料to reverse material 翻料 wet station沾湿台 Tiana天那水cleaning cloth抹布 to load material上料to unload material卸料to return material/stock to退料 scraped |'skr?pid|报废scrape ..v.刮;削 deficient purchase来料不良 manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化 scratch刮伤 dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲 production capacity生产力education and training教育与训练 proposal improvement提案改善spare parts=buffer备件 forklift叉车 trailer=long vehicle拖板车compound die合模 die locker锁模器pressure plate=plate pinch压板 bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子 thickness gauge厚薄规gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签identifying sheet list标示单 location地点 present members出席人员 subject主题conclusion结论 decision items决议事项 responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表 model机锺work order工令 revision版次 remark备注 production control confirmation生产确认checked by初审 approved by核准 department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存 available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计 cause description原因说明part number/ P/N 料号type形态 item/group/class类别 quality品质 prepared by制表 notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量 physical count quantity帐面数量 difference quantity差异量cause analysis原因分析 raw materials原料 materials物料 finished product成品semi-finished product半成品 packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品 disposed goods处理品 warehouse/hub仓库on way location在途仓 oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓 skid/pallet栈板 tox machine自铆机 wire EDM线割EDM放电机 coil stock卷料 sheet stock片料 tolerance工差 score=groove压线 cam block滑块pilot导正筒 trim剪外边 pierce剪内边 drag form压锻差pocket for the punch head挂鈎槽 slug hole废料孔 feature die公母模expansion dwg展开图 radius半径 shim(wedge)楔子 torch-flame cut火焰切割set screw止付螺丝 form block折刀 stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子 stock locater block定位块under cut=scrap chopper清角active plate活动板 baffle plate挡块 cover plate盖板 male die公模 female die母模groove punch压线冲子 air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板bushing block衬套 insert 入块 club car高尔夫球车 capability能力parameter参数 factor系数 phosphate皮膜化成 viscosity涂料粘度 alkalidipping脱脂main manifold主集流脉 bezel斜视规 blanking穿落模 dejecting顶固模 demagnetization去磁;消磁high-speed transmission高速传递 heat dissipation热传 rack上料 degrease脱脂 rinse水洗alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理seal封孔 revision版次 part number/P/N料号 good products良品 scraped products报放心品defective products不良品 finished products成品 disposed products处理品 barcode条码flow chart流程表单 assembly组装 stamping冲压 molding成型 spare parts=buffer备品coordinate座标 dismantle the die折模 auxiliary fuction辅助功能 poly-line多义线heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾 derusting machine除锈机degate打浇口 dryer烘乾机 induction感应 induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕?? shine亮班splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒grit maker抽粒机 cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金lathe车 mill锉 plane刨 grind磨 drill铝 boring镗 blinster气泡 fillet镶;嵌边through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank摸柄crank shaft曲柄轴 augular offset角度偏差 velocity速度production tempo生产进度现状 torque扭矩spline=the multiple keys花键 quenching淬火tempering回火 annealing退火 carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单volatile挥发性 resistance电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机。
工厂生产常用英文术语缩写
工厂生产常用英文术语缩写工厂生产常用英文术语缩写5S : 5S管理ABC : 作业制成本制度 (Activity-Based Costing)ABB : 实施作业制预算制度 (Activity-Based Budgeting)ABM : 作业制成本管理 (Activity-Base Management)APS : 先进规画与排程系统(Advanced Planning and Scheduling)ASP : 应用程序服务供货商（Application Service Provider）ATP : 可承诺量 (Available To Promise)AVL : 认可的供货商清单(Approved Vendor List)BOM : 物料清单 (Bill Of Material)BPR : 企业流程再造 (Business Process Reengineering)BSC : 平衡记分卡 (Balanced ScoreCard)BTF : 计划生产 (Build To Forecast)BTO : 订单生产 (Build To Order)CPM : 要径法 (Critical Path Method)CPM : 每一百万个使用者会有几次抱怨(Complaint per Million) CRM : 客户关系管理 (Customer Relationship Management)CRP : 产能需求规划 (Capacity Requirements Planning)CTO : 客制化生产 (Configuration To Order)DBR : 限制驱导式排程法 (Drum-Buffer-Rope)DMT : 成熟度验证(Design Maturing T esting)DVT : 设计验证(Design Verification Testing)DRP : 运销资源计划 (Distribution Resource Planning)DSS : 决策支持系统 (Decision Support System)EC : 设计变更／工程变更 (Engineer Change)EC : 电子商务 (Electronic Commerce)ECRN : 原件规格更改通知(Engineer Change Request Notice) EDI : 电子数据交换 (Electronic Data Interchange)EIS : 主管决策系统 (Executive Information System)EMC : 电磁相容(Electric Magnetic Capability)EOQ : 基本经济订购量 (Economic Order Quantity)ERP : 企业资源规划 (Enterprise Resource Planning)FAE : 应用工程师(Field Application Engineer)FCST : 预估(Forecast)FMS : 弹性制造系统 (Flexible Manufacture System)FQC : 成品质量管理 (Finish or Final Quality Control)IPQC: 制程质量管理 (In-Process Quality Control)IQC : 进料质量管理 (Incoming Quality Control)ISO : 国际标准组织(International Organization for Standardization)ISAR: 首批样品认可(Initial Sample Approval Request)JIT : 实时管理 (Just In Time)KM ：知识管理 (Knowledge Management)L4L : 逐批订购法 (Lot-for-Lot)LTC : 最小总成本法 (Least Total Cost)LUC : 最小单位成本 (Least Unit Cost)MES : 制造执行系统 (Manufacturing Execution System)MO : 制令(Manufacture Order)MPS : 主生产排程 (Master Production Schedule)MRO : 请修(购)单(Maintenance Repair Operation)MRP : 物料需求规划 (Material Requirement Planning)MRPII : 制造资源计划 (Manufacturing Resource Planning)NFCF : 更改预估量的通知Notice for Changing ForecastOEM : 委托代工 (Original Equipment Manufacture)ODM : 委托设计与制造 (Original Design & Manufacture)OLAP : 在线分析处理 (On-Line Analytical Processing)OLTP : 在线交易处理 (On-Line Transaction Processing)OPT : 最佳生产技术 (Optimized Production Technology) OQC : 出货质量管理 (Out-going Quality Control)PDCA : PDCA管理循环 (Plan-Do-Check-Action)PDM : 产品数据管理系统 (Product Data Management) PERT : 计划评核术 (Program Evaluation and Review Technique) PO : 订单(Purchase Order)POH : 预估在手量 (Product on Hand)PR : 采购申请Purchase RequestQA : 品质保证(Quality Assurance)QC : 质量管理(Quality Control)QCC : 品管圈 (Quality Control Circle)QE : 品质工程(Quality Engineering)RCCP : 粗略产能规划 (Rough Cut Capacity Planning)RMA : 退货验收Returned Material ApprovalROP : 再订购点 (Re-Order Point)SCM : 供应链管理 (Supply Chain Management)SFC : 现场控制 (Shop Floor Control)SIS : 策略信息系统 (Strategic Information System)SO : 订单(Sales Order)SOR : 特殊订单需求(Special Order Request)SPC : 统计制程管制 (Statistic Process Control)TOC : 限制理论 (Theory of Constraints)TPM : 全面生产管理Total Production ManagementTQC : 全面质量管理 (Total Quality Control)TQM : 全面品质管理 (Total Quality Management)WIP : 在制品 (Work In Process)。
工厂专业英语术语
工廠專業英語術語Assembly line組裝線Layout佈置圖Conveyer流水線物料板Rivet table拉釘機Rivet gun拉釘槍Screw driver起子Pneumatic screw driver氣動起子worktable 工作桌OOBA開箱檢查fit together組裝在一起fasten鎖緊(螺絲) fixture 夾具(治具) pallet棧板barcode條碼barcode scanner條碼掃描器fuse together熔合fuse machine熱熔機repair修理operator作業員QC品管supervisor 課長ME製造工程師MT製造生技cosmetic inspect外觀檢查inner parts inspect內部檢查thumb screw大頭螺絲lbs. inch鎊、英寸EMI gasket導電條front plate前板rear plate後板chassis 基座bezel panel面板power button電源按鍵reset button重置鍵Hi-pot test of SPS高源高壓測試Voltage switch of SPS 電源電壓接拉鍵sheet metal parts 沖件plastic parts塑膠件SOP製造作業程式material check list物料檢查表work cell工作間trolley台車carton紙箱sub-line 支線left fork叉車personnel resource department 人力資源部production department生產部門planning department企劃部QC Section品管科stamping factory衝壓廠painting factory烤漆廠molding factory成型廠common equipment常用設備uncoiler and strai ghtener整平機punching machine 衝床robot機械手hydraulic machine油壓機lathe車床planer |'plein?|刨床miller銑床grinder磨床linear cutting線切割electrical sparkle電火花welder電焊機staker=reviting machine鉚合機position職務president董事長general manager總經理special assistant manager特助factory director廠長department director部長deputy manager | =vice manager副理section supervisor課長deputy section supervisor =vice section superisor副課長group leader/supervisor組長line supervisor線長assistant manager助理to move, to carry, to handle搬運be put in storage入庫pack packing包裝to apply oil擦油to file burr 銼毛刺final inspection終檢to connect material接料to reverse material 翻料wet station沾濕台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|報廢scrape ..v.刮;削deficient purchase來料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮傷dents壓痕defective upsiding down抽芽不良defective to staking鉚合不良embedded lump鑲塊feeding is not in place送料不到位stamping-missing漏沖production capacity生產力education and training教育與訓練proposal improvement提案改善spare parts=buffer備件forklift叉車trailer=long vehicle拖板車compound die合模die locker鎖模器pressure plate=plate pinch壓板bolt螺栓administration/general affairs dept總務部automatic screwdriver電動啟子thickness gauge厚薄規gauge(or jig)治具power wire電源線buzzle蜂鳴器defective product label不良標籤identifying sheet list標示單location地點present members出席人員subject主題conclusion結論decision items決議事項responsible department負責單位pre-fixed finishing date預定完成日approved by / checked by / prepared by核准/審核/承辦PCE assembly production schedule sheet PCE組裝廠生產排配表model機鍾work order工令revision版次remark備註production control confirmation生產確認checked by初審approved by核准department部門stock age analysis sheet 庫存貨齡分析表on-hand inventory現有庫存available material良品可使用obsolete material良品已呆滯to be inspected or reworked 待驗或重工total合計cause description原因說明part number/ P/N 料號type形態item/group/class類別quality品質prepared by製錶notes說明year-end physical inventory difference analysis sheet 年終盤點差異分析表physical inventory盤點數量physical count quantity帳面數量difference quantity差異量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods處理品warehouse/hub倉庫on way location在途倉oversea location海外倉spare parts physical inventory list備品盤點清單spare molds location模具備品倉skid/pallet棧板tox machine自鉚機wire EDM線割EDM放電機coil stock卷料sheet stock片料tolerance工差score=groove壓線cam block滑塊pilot導正筒trim剪外邊pierce剪內邊drag form壓鍛差pocket for the punch head掛鈎槽slug hole廢料孔feature die公母模expansion dwg展開圖radius半徑shim(wedge)楔子torch-flame cut火焰切割set screw止付螺絲form block折刀stop pin定位銷round pierce punch=die button圓衝子shape punch=die insert異形子stock locater block定位塊under cut=scrap chopper清角active plate活動板baffle plate擋塊cover plate蓋板male die公模female die母模groove punch壓線衝子air-cushion eject-rod氣墊頂杆spring-box eject-plate彈簧箱頂板bushing block襯套insert 入塊club car高爾夫球車capability能力parameter參數factor係數phosphate皮膜化成viscosity塗料粘度alkalidipping脫脂main manifold主集流脈bezel斜視規blanking穿落模dejecting頂固模demagnetization去磁;消磁high-speed transmission高速傳遞heat dissipation熱傳rack上料degrease脫脂rinse水洗alkaline etch齡咬desmut剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔revision版次part number/P/N料號good products良品scraped products報放心品defective products不良品finished products成品disposed products處理品barcode條碼flow chart流程表單assembly組裝stamping衝壓molding成型spare parts=buffer備品coordinate座標dismantle the die折模auxiliary fuction輔助功能poly-line多義線heater band 加熱片thermocouple熱電偶sand blasting噴沙grit 砂礫derusting machine除鏽機degate打澆口dryer烘乾機induction感應induction light感應光response=reaction=interaction感應ram連杆edge finder巡邊器concave击convex凹short射料不足nick缺口speck瑕?? shine亮班splay 銀紋gas mark焦痕delamination起鱗cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線patent專利grit沙礫granule=peuet=grain細粒grit maker抽粒機cushion緩衝magnalium鎂鋁合金magnesium鎂金metal plate鈑金lathe車mill銼plane刨grind磨drill鋁boring鏜blinster氣泡fillet鑲;嵌邊through-hole form通孔形式voller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸augular offset角度偏差velocity速度production tempo生產進度現狀torque扭矩spline=the multiple keys花鍵quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel鎢高速的moly high speed steel鉬高速的organic solvent有機溶劑bracket小磁導liaison聯絡單volatile揮發性resistance電阻ion離子titrator滴定儀beacon警示燈coolant冷卻液crusher破碎機。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
工厂专业英语术语Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OO BA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板b arcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource departmen t 人力资源部production department生产部门planning department企划部QC Secti on品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thicknes s gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die butto n圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopp er清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizat ion去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料deg rease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer 备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting m achine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine 亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grai n细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenchi ng淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。