ATV61变频器产品介绍

合集下载

施耐德ATV61变频器技术参数

有
故障禁止功能
有
故障复位功能
有
其他
有
诊断功能
故障历史记录
有
当前故障列表
有
更多故障信息
其他
监视功能
输入/输出映象
有
编程卡输入/输出映象
通讯映象通讯映象配置
报警信号组图形显示终端频率给
定变频器内部状态及数
值屏幕显示类型屏幕显示参数数量
其他
有
有有有
有
有
全中文操作界面多
EMC滤波器内置直流电抗器，有可选的线路电抗器
CE, UL, CSA, DNV,CTick,NOM117,GOST
75kW(含75kW)以下标配LED面板， 75kW以上标配LCD中文图形终端 powersuit，方便调试
6，可扩展至10个， 2，可扩展至4个
标配独立PTC输入端子 PWR端子
2 路可编程继电器输出 (NO/NC, NC) 1路可编程电压或电流输出 P24端子提供内部电源
Fipio PL7 FIPIO with messaging
Modbus Plus Uni-Telway, Modbus ASCII, Modbus
RTU/Jbus INTERBUS-S Profibus DP
Ethernet DeviceNet LonWorks
BACnet METASYS N2 Apogee FLN
多参数组切换功能寸动功能
预置速度功能加减速功能
给定附近加减速功能
双斜坡切换功能电机自整定功能
IP20 : 130%持续 60s IP54 : 120%持续 60s
最大600m， 3套
4套参数自动

ATV61变频器_ATV61HU15M3施耐德变频器说明书

ATV61变频器_ATV61HU15M3施耐德变频器说明书产品参数表说明书ATV61HU15M3ATV61 1.5kW 3P 220VAC, 1.5KW,普通涂层,中⽂⾯板,EMC主要信息产品系列Altivar 61产品类型变频器应⽤领域泵机和通风机组件名称ATV61电动机功率 (kW)0.75 kW 单相 200...240 V 1.5 kW 3 相 200...240 V 电机功率 1 hp 单相 200...240 V 2 hp 3 相 200...240 V 电源电压200...240 V (- 15...10 %)电源相数 3 相单相线路电流11.3 A 适⽤200 V 3 相 1.5 kW / 2 hp 12 A 适⽤200 V 单相 0.75 kW / 1 hp 9.6 A 适⽤240 V 3 相 1.5 kW / 2 hp 9.9 A 适⽤240 V 单相 0.75 kW / 1 hp EMC 滤波器C2类EMC滤波器组装⽅式带散热⽚视在功率2.4 kVA 适⽤240 V 单相 0.75 kW / 1 hp 4 kVA 适⽤240 V 3 相 1.5 kW / 2 hp 最⼤预期短路电流Isc 5 kA 3 相5 kA 单相最⼤瞬变电流 5.7 A 适⽤60 s 单相9.6 A 适⽤60 s 3 相额定开关频率12 kHz开关频率 1...16 kHz 可调12...16 kHz 带降额因素异步电机控制电压/频率⽐，2点电压/频率⽐，5点⽆传感器磁链⽮量控制标准电压/频率⽐同步电机控制配置模式⽆传感器⽮量控制通讯端⼝协议CANopen Modbus极化⽅式⽆阻抗适⽤ Modbus 选项卡APOGEE FLN 通信卡BACnet 通信卡责声明：本⽂档不代表或不⽤于确定⽤于特定⽤户应⽤产品的适⽤性或可靠性控制器内可编程卡DeviceNet 通信卡Ethernet/IP 通信卡Fipio 通信卡I/O 扩展卡Interbus-S 通信卡LonWorks 通信卡METASYS N2 通信卡Modbus Plus 通信卡Modbus TCP 通信卡Modbus/Uni-Telway 通信卡泵站控制卡Profibus DP 通信卡Profibus DP V1 通信卡补充信息产品功能异步电机同步电机电源电压上限170...264 V供电电源频率50...60 Hz (- 5...5 %)电源频率限制47.5...63 Hz连续输出电流8 A 12 kHz, 230 V 3 相4.8 A 12 kHz, 230 V 单相最⼤输出频率0.1...599 Hz速度范围 1...100 处于开环模式下, ⽆速度反馈速度精度+/- 10 % 标称滑距适⽤ 0.2 Tn ⾄ Tn 转矩变化不带速度反馈扭矩精度+/- 15 % 处于开环模式下, ⽆速度反馈瞬时过转矩130 % 标称电机转矩, +/- 10 % 适⽤ 60 秒制动⼒矩30 % 不带制动电阻器<= 125 % 带有制动电阻器调节回路频率 PI 调节器电机滑差补偿可调⾃动⽆论负载情况可以抑制不可⽤电压/频率⽐（2 或 5 点）诊断 1 个LED 红⾊状态设备电压输出电压<= 电源电压电⽓隔离电源与控制端⼦之间安装在外壳中的电缆的类型带有⼀个 IP21 或 IP31 套件 : 3-绞股 IEC 电缆在…上 40 °C, 铜 70 °C PVC 不带安装套件 : 1-绞股 IEC 电缆在…上 45 °C, 铜 70 °C PVC不带安装套件 : 1-绞股 IEC 电缆在…上 45 °C, 铜 90 °C XLPE/EPR带有UL 1类套件 : 3-绞股 UL 508 电缆在…上 40 °C, 铜 75 °C PVC电⽓连接AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 端⼦ 2.5 mm2 / AWG 14L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 端⼦ 6 mm2 / AWG 8紧固扭矩AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 0.6 N.mL1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 1.4 N.m / 12.3 lb.内部电源内部电源⽤于参考电位计 (1 ⾄ 10 kOhm) 10.5 V 直流 +/- 5 %, <= 10 mA 适⽤过载和短路保护内部电源 24 V 直流 (21...27 V), <= 200 mA 适⽤过载和短路保护来⾃外部供电 24 V 直流 (19...30 V)模拟量输⼊数量2模拟量输⼊类型AI1-/Al1+ 双极差分电压 +/- 10 V 直流, 输⼊电压 24 V 最⼤, 分辨率 11位+符号位AI2 软件-可配置电流 0...20 mA, 阻抗 242 ?, 分辨率 11 位AI2 软件-可配置电压 0...10 V 直流, 输⼊电压 24 V 最⼤, 阻抗 30000 ?, 分辨率 11 位采样时间离散量输⼊ LI6 (如果配置为逻辑输⼊的话) 2 ms, +/- 0.5 ms模拟量输⼊ AI1-/Al1+ 2 ms, +/- 0.5 ms模拟量输⼊ Al2 2 ms, +/- 0.5 ms模拟量输出 AO1 2 ms, +/- 0.5 ms离散量输⼊ LI1...LI5 2 ms, +/- 0.5 ms绝对精度AI1-/Al1+ +/- 0.6 % ⽤于60 °C的温度变动AI2 +/- 0.6 % ⽤于60 °C的温度变动AO1 +/- 1 % ⽤于60 °C的温度变动线性度误差AI1-/Al1+ 最⼤值 +/- 0.15 %AI2 最⼤值 +/- 0.15 %模拟量输出数量1模拟量输出型号AO1 软件-可配置电流, 模拟量输出范围 0...20 mA, 阻抗 500 ?, 分辨率 10 bits AO1 软件-可配置逻辑输出 10 V, <= 20 mAAO1 软件-可配置电压, 模拟量输出范围 0...10 V DC, 阻抗 470 ?, 分辨率 10 bits 离散量输出数量2指⽰装置类型(R1A, R1B, R1C) 可配置的继电器逻辑 NO/NC, 电⽓寿命 100000 次(R2A, R2B) 可配置的继电器逻辑 NO, 电⽓寿命 100000 次最⼤响应时间<= 100 ms 在 STO (安全转矩关闭) 内R1A, R1B, R1C <= 7 ms, 公差 +/- 0.5 msR2A, R2B <= 7 ms, 公差 +/- 0.5 ms最⼩开关电流 [Imin]可配置的继电器逻辑 3 mA 在…上 24 V DC最⼤开关电流R1, R2 在…上阻性（负载）负载, 5 A 30 V DC, cos phi = 1, 0 msR1, R2 在…上感性负载负载, 2 A 30 V DC, cos phi = 0.4, 7 msR1, R2 在…上阻性（负载）负载, 5 A 250 V AC, cos phi = 1, 0 msR1, R2 在…上感性负载负载, 2 A 250 V AC, cos phi = 0.4, 7 ms离散量输⼊数量7数字量输⼊类型(LI1...LI5) 可编程, 24 V 直流, 电压限制 <= 30 V, 有 1 级 PLC, 阻抗 3500 ?(LI6) 开关-可配置, 24 V 直流, 电压限制 <= 30 V, 有 1 级 PLC, 阻抗 3500 ?(LI6) 开关可配置 PTC 探头, 0...6, 阻抗 1500 ?(PWR) 安全输⼊, 24 V 直流, 电压限制 <= 30 V, 阻抗 1500 ?离散量输⼊逻辑LI1...LI5 负逻辑 (漏), < 5 V (状态 0), > 11 V (状态 1)LI1...LI5 负逻辑 (漏), > 16 V (状态 0), < 10 V (状态 1)LI6 (如果配置为逻辑输⼊的话) 负逻辑 (漏), > 16 V (状态 0), < 10 V (状态 1)LI6 (如果配置为逻辑输⼊的话) 负逻辑 (漏), < 5 V (状态 0), > 11 V (状态 1)加速和减速倾斜超出刹车能⼒时的坡道⾃适应，采⽤电阻从 0.01 ⾄ 9000 s 独⽴线性可调S, U 或⾃定义制动⾄停⽌采⽤直流注⼊保护类型驱动防⽌超出限制速度驱动防⽌输⼊相位丢失驱动控制电路上制动驱动输⼊断相驱动线路电源过压驱动总线供电⽋压驱动输出相线和接地之间的过流驱动过热保护驱动直流总线过压驱动拆卸电源驱动电机各相线之间短路驱动热保护马达电机断相马达拆卸电源马达热保护绝缘电阻> 1 m? 在…上接地 1 分钟 500 V 直流频率分辨率模拟量输⼊ 0.024/50 Hz显⽰单元 0.1 Hz端⼝类型 1 RJ45 适⽤ Modbus 前⾯板1 RJ45 适⽤ Modbus 接线端RJ45的针型SUB-D 9 适⽤ CANopen物理接⼝2线制RS485 适⽤ Modbus传输帧RTU 适⽤ Modbus传输率20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps 适⽤ CANopen 4800 bps, 9600 bps, 19200 bps, 38.4 Kbps 适⽤ Modbus 接线端9600 bps, 19200 bps 适⽤ Modbus 前⾯板数据格式8 位, 1 停⽌, 偶校验适⽤ Modbus 前⾯板8 位, 奇偶或⽆可配置的校验适⽤ Modbus 接线端地址数 1...247 适⽤ Modbus1...127 适⽤ CANopen访问⽅法从（站）适⽤ CANopen标识CE操作位置垂直⽅向 +/- 10°产品重量 3 kg宽度130 mm⾼度230 mm深度175 mm环境噪⾳等级43 dB 符合 86/188/EEC绝缘性能2830 V DC 接地和电源接线端之间4230 V DC 控制和电源接线端之间电磁兼容性符合 IEC 61000-4-2 级别 3符合 IEC 61000-4-11符合 IEC 61000-4-6 级别 3符合 IEC 61000-4-3 级别 3符合 IEC 61000-4-4 级别 4符合标准EN 55011 A 类第 1 组EN 61800-3 环境 1 级别 C2EN 61800-3 环境 2 级别 C2EN/IEC 61800-3EN/IEC 61800-5-1IEC 60721-3-3 第 3C1 类IEC 60721-3-3 第 3S2 类UL 类型 1产品认证CSAC-TickDNVGOSTNOM 117UL污染等级 2 符合 EN/IEC 61800-5-1保护程度IP20 在上⽅部件封盖上不带盲板符合 EN/IEC 60529 IP20 在上⽅部件封盖上不带盲板符合 EN/IEC 61800-5-1IP21 符合 EN/IEC 60529IP21 符合 EN/IEC 61800-5-1IP41 在上⽅部件符合 EN/IEC 60529IP41 在上⽅部件符合 EN/IEC 61800-5-1IP54 对下⾯的部件符合 EN/IEC 60529IP54 对下⾯的部件符合 EN/IEC 61800-5-1抗振动波峰⾄波峰 1.5 mm (f = 3...13 Hz) 符合 EN/IEC 60068-2-6 1 gn (f = 13...200 Hz) 符合 EN/IEC 60068-2-6抗冲击15 gn 适⽤ 11 ms 符合 EN/IEC 60068-2-27相对湿度 5...95 % ⽆冷凝符合 IEC 60068-2-35...95 % ⽆滴⽔符合 IEC 60068-2-3环境温度-10...50 °C ⽆降容50...60 °C 带降额因素贮存环境温度-25...70 °C⼯作海拔<= 1000 m ⽆降容1000...3000 m 电流降额 1%/100m合同保修阶段18 个⽉。

关于ATV61F与ATV61变频器的说明

ATV61为通用型标准负载变频器，ATV61F是专用于暖通、空调、流体、空冷、石化、泵站系统的变频器，专用负载类型为流体（水或轻质油类）泵、风机等设备，常用于供水、给（排）水、供暖、空调，各类风机等场合。

ATV61F本身带有电抗器及EMC滤波器和通信接口，与ATV61相比集成度略高。

ATV61为通用型变频器，负载类型及软体涵盖范围略广（如：其可应用纺织，矿山等其它类型负载）;ATV61F 为流体泵及各类风机专用变频器，在流体泵及风机负载应用方面，其控制及软体设计更为实用和贴近负载。

其它方面ATV61与ATV61F完全相同！。

Schneider Electric ATV61 2.2kW 3HP 变速驱动器产品说明书

T h e i n f o r m a t i o n p r o v i d e d i n t h i s d o c u m e n t a t i o n c o n t a i n s g e n e r a l d e s c r i p t i o n s a n d /o r t e c h n i c a l c h a r a c t e r i s t i c s o f t h e p e r f o r m a n c e o f t h e p r o d u c t s c o n t a i n e d h e r e i n .T h i s d o c u m e n t a t i o n i s n o t i n t e n d e d a s a s u b s t i t u t e f o r a n d i s n o t t o b e u s e d f o r d e t e r m i n i n g s u i t a b i l i t y o r r e l i a b i l i t y o f t h e s e p r o d u c t s f o r s p e c i f i c u s e r a p p l i c a t i o n s .I t i s t h e d u t y o f a n y s u c h u s e r o r i n t e g r a t o r t o p e r f o r m t h e a p p r o p r i a t e a n d c o m p l e t e r i s k a n a l y s i s , e v a l u a t i o n a n d t e s t i n g o f t h e p r o d u c t s w i t h r e s p e c t t o t h e r e l e v a n t s p e c i f i c a p p l i c a t i o n o r u s e t h e r e o f .N e i t h e r S c h n e i d e r E l e c t r i c I n d u s t r i e s S A S n o r a n y o f i t s a f f i l i a t e s o r s u b s i d i a r i e s s h a l l b e r e s p o n s i b l e o r l i a b l e f o r m i s u s e o f t h e i n f o r m a t i o n c o n t a i n e d h e r e i n .Product data sheetCharacteristicsATV61HU22N4Zvariable speed drive ATV61 - 2.2kW 3HP -380...480V - IP20MainRange of product Altivar 61Product or component typeVariable speed driveProduct specific appli-cationPumping and ventilation machine Component name ATV61Motor power kW 2.2 kW 3 phases at 380...480 V Motor power hp 3 hp 3 phases at 380...480 V Power supply voltage 380...480 V (- 15...10 %)Supply number of phases 3 phasesLine current 8.2 A for 380 V 3 phases 2.2 kW / 3 hp 7.1 A for 480 V 3 phases 2.2 kW / 3 hp EMC filter Level 3 EMC filterVariant Without remote graphic terminal Assembly style With heat sinkApparent power 5.4 kVA for 380 V 3 phases 2.2 kW / 3 hp Maximum prospective line Isc5 kA 3 phases Maximum transient cur-rent6.9 A for 60 s 3 phases Nominal switching fre-quency12 kHzSwitching frequency 12...16 kHz with derating factor 1...16 kHz adjustableAsynchronous motor controlVoltage/Frequency ratio, 2 points Voltage/Frequency ratio, 5 pointsFlux vector control without sensor, standardVoltage/Frequency ratio - Energy Saving, quadratic U/fSynchronous motor control profile Vector control without sensor, standard Communication port protocolCANopen ModbusType of polarization No impedance for ModbusOption cardProfibus DP V1 communication card Profibus DP communication card Multi-pump cardModbus/Uni-Telway communication card Modbus TCP communication card Modbus Plus communication card METASYS N2 communication card LonWorks communication card Interbus-S communication card I/O extension cardFipio communication cardEthernet/IP communication card DeviceNet communication cardController inside programmable card CC-Link communication card BACnet communication cardAPOGEE FLN communication cardComplementaryProduct destination Asynchronous motorsSynchronous motorsPower supply voltage limits323...528 VPower supply frequency50...60 Hz (- 5...5 %)Power supply frequency limits47.5...63 HzContinuous output current 5.8 A at 12 kHz, 380 V 3 phases4.8 A at 12 kHz, 460 V 3 phasesSpeed drive output frequency0.1...599 HzSpeed range 1...100 in open-loop mode, without speed feedbackSpeed accuracy+/- 10 % of nominal slip for 0.2 Tn to Tn torque variation without speed feedback Torque accuracy+/- 15 % in open-loop mode, without speed feedbackTransient overtorque130 % of nominal motor torque, +/- 10 % for 60 sBraking torque30 % without braking resistor<= 125 % with braking resistorRegulation loop Frequency PI regulatorMotor slip compensation AdjustableAutomatic whatever the loadCan be suppressedNot available in voltage/frequency ratio (2 or 5 points)Diagnostic 1 LED red presence of drive voltageOutput voltage<= power supply voltageElectrical isolation Between power and control terminalsType of cable for mounting in an enclosure Without mounting kit : 1-strand IEC cable at 45 °C, copper 90 °C XLPE/EPRWithout mounting kit : 1-strand IEC cable at 45 °C, copper 70 °C PVCWith UL Type 1 kit : 3-strand UL 508 cable at 40 °C, copper 75 °C PVCWith an IP21 or an IP31 kit : 3-strand IEC cable at 40 °C, copper 70 °C PVC Electrical connection L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB terminal 6 mm² /AWG 8AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5mm² / AWG 14Tightening torque L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 1.4 N.m / 12.3 lb.inAI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 0.6 N.m Supply Internal supply 24 V DC (21...27 V), <= 200 mA for overload and short-circuit pro-tectionInternal supply for reference potentiometer (1 to 10 kOhm) 10.5 V DC +/- 5 %, <=10 mA for overload and short-circuit protectionExternal supply 24 V DC (19...30 V), 30 WAnalogue input number2Analogue input type AI2 software-configurable voltage 0...10 V DC, input voltage 24 V max,impedance 30000 Ohm, resolution 11 bitsAI2 software-configurable current 0...20 mA, impedance 242 Ohm, resolution 11bitsAI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max, resolu-tion 11 bits + signSampling time Discrete input LI6 (if configured as logic input) 2 ms, +/- 0.5 msDiscrete input LI1...LI5 2 ms, +/- 0.5 msAnalog output AO1 2 ms, +/- 0.5 msAnalog input Al2 2 ms, +/- 0.5 msAnalog input AI1-/Al1+ 2 ms, +/- 0.5 msAbsolute accuracy precision AO1 +/- 1 % for a temperature variation 60 °CAI2 +/- 0.6 % for a temperature variation 60 °CAI1-/Al1+ +/- 0.6 % for a temperature variation 60 °CLinearity error AO1 +/- 0.2 %AI2 +/- 0.15 % of maximum valueAI1-/Al1+ +/- 0.15 % of maximum valueAnalogue output number1Analogue output type AO1 software-configurable logic output 10 V, <= 20 mAAO1 software-configurable voltage, analogue output range 0...10 V DC,impedance 470 Ohm, resolution 10 bitsAO1 software-configurable current, analogue output range 0...20 mA, impedance500 Ohm, resolution 10 bitsDiscrete output number2Discrete output type(R2A, R2B) configurable relay logic NO, electrical durability 100000 cycles(R1A, R1B, R1C) configurable relay logic NO/NC, electrical durability 100000 cy-clesMaximum response time R2A, R2B <= 7 ms, tolerance +/- 0.5 msR1A, R1B, R1C <= 7 ms, tolerance +/- 0.5 ms<= 100 ms in STO (Safe Torque Off)Minimum switching current Configurable relay logic 3 mA at 24 V DCMaximum switching current R1, R2 on resistive load, 5 A at 30 V DC, cos phi = 1, L/R = 0 msR1, R2 on resistive load, 5 A at 250 V AC, cos phi = 1, L/R = 0 msR1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4, L/R = 7 msR1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4, L/R = 7 ms Discrete input number7Discrete input type(PWR) safety input, 24 V DC, voltage limits <= 30 V, impedance 1500 Ohm(LI6) switch-configurable PTC probe, 0...6, impedance 1500 Ohm(LI6) switch-configurable, 24 V DC, voltage limits <= 30 V, with level 1 PLC,impedance 3500 Ohm(LI1...LI5) programmable, 24 V DC, voltage limits <= 30 V, with level 1 PLC,impedance 3500 OhmDiscrete input logic LI6 (if configured as logic input) positive logic (source), < 5 V (state 0), > 11 V(state 1)LI6 (if configured as logic input) negative logic (sink), > 16 V (state 0), < 10 V(state 1)LI1...LI5 positive logic (source), < 5 V (state 0), > 11 V (state 1)LI1...LI5 negative logic (sink), > 16 V (state 0), < 10 V (state 1) Acceleration and deceleration ramps Automatic adaptation of ramp if braking capacity exceeded, by using resistorLinear adjustable separately from 0.01 to 9000 sS, U or customizedBraking to standstill By DC injectionProtection type Motor thermal protectionMotor power removalMotor motor phase breakDrive thermal protectionDrive short-circuit between motor phasesDrive power removalDrive overvoltages on the DC busDrive overheating protectionDrive overcurrent between output phases and earthDrive line supply undervoltageDrive line supply overvoltageDrive input phase breaksDrive break on the control circuitDrive against input phase lossDrive against exceeding limit speedInsulation resistance> 1 mOhm at 500 V DC for 1 minute to earthFrequency resolution Display unit 0.1 HzAnalog input 0.024/50 HzType of connector Male SUB-D 9 on RJ45 for CANopen1 RJ45 for Modbus on terminal1 RJ45 for Modbus on front facePhysical interface2-wire RS 485 for ModbusTransmission frame RTU for ModbusTransmission rate20 kbps, 50 kbps, 125 kbps, 250 kbps, 500 kbps, 1 Mbps for CANopen9600 bps, 19200 bps for Modbus on front face4800 bps, 9600 bps, 19200 bps, 38.4 Kbps for Modbus on terminalData format8 bits, odd even or no configurable parity for Modbus on terminal8 bits, 1 stop, even parity for Modbus on front faceNumber of addresses 1...247 for Modbus1...127 for CANopenMethod of access Slave for CANopenMarking CEOperating position Vertical +/- 10 degreeProduct weight 3 kgWidth130 mmHeight230 mmDepth175 mmEnvironmentNoise level43 dB conforming to 86/188/EECDielectric strength5092 V DC between control and power terminals3535 V DC between earth and power terminalsElectromagnetic compatibility Voltage dips and interruptions immunity test conforming to IEC 61000-4-11Radiated radio-frequency electromagnetic field immunity test conforming to IEC61000-4-3 level 3Electrostatic discharge immunity test conforming to IEC 61000-4-2 level 3Electrical fast transient/burst immunity test conforming to IEC 61000-4-4 level 4Conducted radio-frequency immunity test conforming to IEC 61000-4-6 level 3 Standards EN 55011 class A group 1EN 61800-3 environments 1 category C2EN 61800-3 environments 2 category C2EN/IEC 61800-3EN/IEC 61800-5-1IEC 60721-3-3 class 3C1IEC 60721-3-3 class 3S2UL Type 1Product certifications CSAC-TickDNVGOSTNOM 117ULPollution degree 2 conforming to EN/IEC 61800-5-1Degree of proctection IP54 on lower part conforming to EN/IEC 61800-5-1IP54 on lower part conforming to EN/IEC 60529IP41 on upper part conforming to EN/IEC 61800-5-1IP41 on upper part conforming to EN/IEC 60529IP21 conforming to EN/IEC 61800-5-1IP21 conforming to EN/IEC 60529IP20 on upper part without blanking plate on cover conforming to EN/IEC61800-5-1IP20 on upper part without blanking plate on cover conforming to EN/IEC 60529 Vibration resistance 1.5 mm peak to peak (f = 3...13 Hz) conforming to EN/IEC 60068-2-61 gn (f = 13...200 Hz) conforming to EN/IEC 60068-2-6Shock resistance15 gn for 11 ms conforming to EN/IEC 60068-2-27Relative humidity 5...95 % without dripping water conforming to IEC 60068-2-35...95 % without condensation conforming to IEC 60068-2-3Ambient air temperature for operation50...60 °C with derating factor-10...50 °C without deratingAmbient air temperature for storage-25...70 °COperating altitude1000...3000 m with current derating 1 % per 100 m<= 1000 m without deratingProduct data sheetATV61HU22N4Z Dimensions DrawingsVariable Speed Drives without Graphic Display TerminalDimensions without Option CardDimensions in mmDimensions in in.Dimensions with 1 Option Card (1)Dimensions in mmDimensions in in.(1) Option cards: I/O extension cards, communication cards or "Controller Inside” programmable card. Dimensions with 2 Option Cards (1)Dimensions in mmDimensions in in.(1) Option cards: I/O extension cards, communication cards or "Controller Inside” programmable card.Product data sheetATV61HU22N4ZMounting and ClearanceMounting RecommendationsDepending on the conditions in which the drive is to be used, its installation will require certain precautions and the use of appropriate accessories.Install the unit vertically:●Avoid placing it close to heating elements●Leave sufficient free space to ensure that the air required for cooling purposes can circulate from the bottom to the top of the unit. ClearanceMounting TypesType A MountingType B MountingType C MountingBy removing the protective blanking cover from the top of the drive, the degree of protection for the drive becomes IP 20.The protective blanking cover may vary according to the drive model (refer to the user guide).Specific Recommendations for Mounting the Drive in an EnclosureVentilationTo ensure proper air circulation in the drive:●Fit ventilation grilles.●Ensure that there is sufficient ventilation. If there is not, install a forced ventilation unit with a filter. The openings and/or fans must providea flow rate at least equal to that of the drive fans (refer to the product characteristics).●Use special filters with IP 54 protection.●Remove the blanking cover from the top of the drive.Dust and Damp Proof Metal Enclosure (IP 54)The drive must be mounted in a dust and damp proof enclosure in certain environmental conditions: dust, corrosive gases, high humidity with risk of condensation and dripping water, splashing liquid, etc.This enables the drive to be used in an enclosure where the maximum internal temperature reaches 50°C.Product data sheetATV61HU22N4ZConnections and SchemaWiring Diagram Conforming to Standards EN 954-1 Category 1, IEC/EN 61508 Capacity SIL1, in Stopping Category 0 According to IEC/EN 60204-1Three-Phase Power Supply with Upstream Breaking via ContactorA1ATV61 driveKM1ContactorL1DC chokeQ1Circuit-breakerQ2GV2 L rated at twice the nominal primary current of T1Q3GB2CB05XB4 B or XB5 A pushbuttonsS1,S2T1100 VA transformer 220 V secondary(1)Line choke (three-phase); mandatory for ATV61HC11Y…HC80Y drives (except when a special transformer is used (12-pulse)).(2)For ATV61HC50N4, ATV61HC63N4 and ATV61HC50Y…HC80Y drives, refer to the power terminal connections diagram.(3)Fault relay contacts. Used for remote signalling of the drive status.(4)Connection of the common for the logic inputs depends on the positioning of the SW1 switch. The above diagram shows the internalpower supply switched to the “source” position (for other connection types, refer to the user guide).(5)There is no PO terminal on ATV61HC11Y…HC80Y drives.(6)Optional DC choke for ATV61H•••M3, ATV61HD11M3X…HD45M3X and ATV61H075N4…HD75N4 drives. Connected in place of thestrap between the PO and PA/+ terminals. For ATV61HD55M3X…HD90M3X, ATV61HD90N4…HC63N4 drives, the choke is supplied with the drive; the customer is responsible for connecting it. For ATV61W•••N4 and ATV61W•••N4C drives, the DC choke is integrated.(7)Software-configurable current (0…20 mA) or voltage (0…10 V) analog input.(8)Reference potentiometer.NOTE: All terminals are located at the bottom of the drive. Fit interference suppressors on all inductive circuits near the drive or connected on the same circuit, such as relays, contactors, solenoid valves, fluorescent lighting, etc.Wiring Diagram Conforming to Standards EN 954-1 Category 1, IEC/EN 61508 Capacity SIL1, in Stopping Category 0 According to IEC/EN 60204-1Three-Phase Power Supply with Downstream Breaking via Switch DisconnectorA1ATV61 driveL1DC chokeQ1Circuit-breakerQ2Switch disconnector (Vario)(1)Line choke (three-phase), mandatory for ATV61HC11Y…HC80Y drives (except when a special transformer is used (12-pulse)).(2)For ATV61HC50N4, ATV61HC63N4 and ATV61HC50Y…HC80Y drives, refer to the power terminal connections diagram.(3)Fault relay contacts. Used for remote signalling of the drive status.(4)Connection of the common for the logic inputs depends on the positioning of the SW1 switch. The above diagram shows the internalpower supply switched to the “source” position (for other connection types, refer to the user guide).(5)There is no PO terminal on ATV61HC11Y…HC80Y drives.(6)Optional DC choke for ATV61H•••M3, ATV61HD11M3X…HD45M3X and ATV61H075N4…HD75N4 drives. Connected in place of thestrap between the PO and PA/+ terminals. For ATV61HD55M3X…HD90M3X, ATV61HD90N4…HC63N4 drives, the choke is supplied with the drive; the customer is responsible for connecting it. For ATV61W•••N4 and ATV61W•••N4C drives, the DC choke is integrated.(7)Software-configurable current (0…20 mA) or voltage (0…10 V) analog input.(8)Reference potentiometer.NOTE: All terminals are located at the bottom of the drive. Fit interference suppressors on all inductive circuits near the drive or connected on the same circuit, such as relays, contactors, solenoid valves, fluorescent lighting, etc.Wiring Diagram Conforming to Standards EN 954-1 Category 3, IEC/EN 61508 Capacity SIL2, in Stopping Category 0 According to IEC/EN 60204-1Three-Phase Power Supply, Low Inertia Machine, Vertical MovementA1ATV61 drive A2Preventa XPS AC safety module for monitoring emergency stops and switches. One safety module can manage the “Power Removal”function for several drives on the same machine. In this case, each drive must connect its PWR terminal to its + 24 V via the safety contacts on the XPS AC module. These contacts are independent for each drive.F1Fuse L1DC choke Q1Circuit-breaker S1Emergency stop button with 2 contacts S2XB4 B or XB5 A pushbutton (1)Power supply: 24 Vdc or Vac, 115 Vac, 230 Vac.(2)S2: resets XPS AC module on power-up or after an emergency stop. ESC can be used to set external starting conditions.(3)Requests freewheel stopping of the movement and activates the “Power Removal” safety function.(4)Line choke (three-phase), mandatory for and ATV61HC11Y…HC80Y drives (except when a special transformer is used (12-pulse)).(5)The logic output can be used to signal that the machine is in a safe stop state.(6)For ATV61HC50N4, ATV61HC63N4 and ATV61HC50Y…HC80Y drives, refer to the power terminal connections diagram.(7)Fault relay contacts. Used for remote signalling of the drive status.(8)Connection of the common for the logic inputs depends on the positioning of the SW1 switch. The above diagram shows the internal power supply switched to the “source” position (for other connection types, refer to the user guide).(9)Standardized coaxial cable, type RG174/U according to MIL-C17 or KX3B according to NF C 93-550, external diameter 2.54 mm /0.09 in., maximum length 15 m / 49.21 ft. The cable shielding must be earthed.(10)There is no PO terminal on ATV61HC11Y…HC80Y drives.(11)Optional DC choke for ATV61H•••M3, ATV61HD11M3X…HD45M3X and ATV61H075N4…HD75N4 drives. Connected in place of the strap between the PO and PA/+ terminals. For ATV61HD55M3X…HD90M3X, ATV61HD90N4…HC63N4 drives, the choke is supplied with the drive; the customer is responsible for connecting it. For ATV61W•••N4 and ATV61W•••N4C drives, the DC choke is integrated.(12)Software-configurable current (0…20 mA) or voltage (0…10 V) analog input.(13)Reference potentiometer.NOTE: All terminals are located at the bottom of the drive. Fit interference suppressors on all inductive circuits near the drive or connected on the same circuit, such as relays, contactors, solenoid valves, fluorescent lighting, etc.Wiring Diagram Conforming to Standards EN 954-1 Category 3, IEC/EN 61508 Capacity SIL2, in Stopping Category 1 According to IEC/EN 60204-1Three-Phase Power Supply, High Inertia MachineA1ATV61 drive A2(5)Preventa XPS ATE safety module for monitoring emergency stops and switches. One safety module can manage the "Power Removal”safety function for several drives on the same machine. In this case the time delay must be adjusted on the drive controlling the motor that requires the longest stopping time. In addition, each drive must connect its PWR terminal to its + 24 V via the safety contacts on the XPS ATE module. These contacts are independent for each drive.F1Fuse L1DC choke Q1Circuit-breaker S1Emergency stop button with 2 contacts S2XB4 B or XB5 A pushbutton (1)Power supply: 24 Vdc or Vac, 115 Vac, 230 Vac.(2)Requests controlled stopping of the movement and activates the “Power Removal” safety function.(3)Line choke (three-phase), mandatory for ATV61HC11Y…HC80Y drives (except when a special transformer is used (12-pulse)).(4)S2: resets XPS ATE module on power-up or after an emergency stop. ESC can be used to set external starting conditions.(5)The logic output can be used to signal that the machine is in a safe state.(6)For stopping times requiring more than 30 seconds in category 1, use a Preventa XPS AV safety module which can provide a maximum time delay of 300 seconds.(7)For ATV61HC50N4, ATV61HC63N4 and ATV61HC50Y…HC80Y drives, refer to the power terminal connections diagram.(8)Fault relay contacts. Used for remote signalling of the drive status.(9)Connection of the common for the logic inputs depends on the positioning of the SW1 switch. The above diagram shows the internal power supply switched to the “source” position (for other connection types, refer to the user guide).(10)Standardized coaxial cable, type RG174/U according to MIL-C17 or KX3B according to NF C 93-550, external diameter 2.54 mm/0.09 in., maximum length 15 m/49.21 ft. The cable shielding must be earthed.(11)Logic inputs LI1 and LI2 must be assigned to the direction of rotation: LI1 in the forward direction and LI2 in the reverse direction.(12)There is no PO terminal on ATV61HC11Y…HC80Y drives.(13)Optional DC choke for ATV61H•••M3, ATV61HD11M3X…HD45M3X and ATV61H075N4…HD75N4 drives. Connected in place of the strap between the PO and PA/+ terminals. For ATV61HD55M3X…HD90M3X, ATV61HD90N4…HC63N4 drives, the choke is supplied with the drive; the customer is responsible for connecting it. For ATV61W•••N4 and ATV61W•••N4C drives, the DC choke is integrated.(14)Software-configurable current (0…20 mA) or voltage (0…10 V) analog input.(15)Reference potentiometer.NOTE: All terminals are located at the bottom of the drive. Fit interference suppressors on all inductive circuits near the drive or connected on the same circuit, such as relays, contactors, solenoid valves, fluorescent lighting, etc.Product data sheet Performance Curves ATV61HU22N4ZDerating CurvesThe derating curves for the drive nominal current (In) depend on the temperature, the switching frequency and the mounting type (A, B or C).For intermediate temperatures (e.g. 55°C), interpolate between 2 curves.X Switching frequency。

ATV基本特性

61HD11N4 11
15
ATV61HD15N4 15
20
ATV61HD18N4 18.5
25
ATV61HD22N4 22
30
ATV61HD30N4 30
对355kw以上的规格,由于区别于 ATV68的双柜体形式，体积和表面积实际减少了一半
7
480V 三相规格的电流
型号
电机
kW
HP
ATV61H075N4 0.75
1
ATV61HU15N4 1.5
2
ATV61HU22N4 2.2
3
AT V61HU30N4
3
-
AT V61HU40N4
4
5
ATV61HU55N4 5.5
ATV38/68型号 ATV38HU18N4 ATV38HU29N4 ATV38HU41N4 ATV38HU54N4 ATV38HU72N4 ATV38HU90N4 ATV38HD12N4 ATV38HD16N4 ATV38HD23N4 ATV38HD25N4 ATV38HD28N4 ATV38HD33N4 ATV38HD46N4 ATV38HD54N4 ATV38HD64N4 ATV38HD79N4 ATV38C10N4 ATV38C13N4 ATV38C15N4 ATV38C19N4 ATV38C25N4 ATV38C28N4 ATV38C33N4 ATV68C43N4 ATV68C53N4 ATV68C63N4
不带图形终端
-30% -30% -30% -30% -30% -10% -47% -26% -14%
* * * * * * *
* * * * * * * * * *
体积/ATV38-68 *

施耐德_ATV_61_系列变频器说明书

ATV61变频器针对 0.75 至 2400 kW 三相同异步电机产品泵和风机会消耗大量的能源，特别是在工业环境和基础设施领域。

通过这种新一代的变频器，施耐德电气利用其在速度控制领域中范围广泛的专业技术和技能，协助您提高竞争力，保护您的设施，降低您的维护成本，同时保持环境友好性。

出众的性能、先进的功能...同时又一直强调简便性。

对所有通信网络、应用、用户等开放。

ATV61 标准转矩产品针对您的所有特殊需求提供了独创性的解决方案。

控制您的能耗■其节能可使能耗削减50%。

■在变频器控制下，流量为额定值 80% 时的电机功率仅对应额定功率的50%，而在传统控制方式下则为 95%。

■ATV61 提供多种控制比率：- 二次比率 (Kn2)。

- 电压/频率比 (2 或 5 个点)。

- 节能比：根据施加在设备上的负载来优化能耗。

■减少电流谐波 (直流电抗器、无源滤波器等)。

ATV61前沿产品！强大的产品阵容■ IP20，UL 1 型，三相 200 至 240 V：ATV61 0.75 至 90 kW■ IP20，UL 1 型，三相 380至 480 V：ATV61 0.75 至 630 kW■ IP20，UL 1 型，三相 500 至 690 V：ATV61 2.2 至 800 kW■ IP54，UL 12 型，三相 380 至 480 V：ATV61 0.75 至 90 kW■ IP23/54，柜式变频器，三相 380 至 480 V：ATV61 90 至 1400 kW■ IP23/54，柜式变频器，三相 500 至 690 V：ATV61 90 至 2400 kW■集成 A 级或 B 级 EMC 滤波器。

■适应全世界要求的产品：UL、CSA、CE、C-Tick、DNV、GOST、ATEX ...可扩展的功能基本设备配有多种功能：应用功能、输入/输出、通信网络等等，可通过以下板卡进一步扩展：■输入/输出扩展卡。

施耐德atv61中文说明书

施耐德atv61中文说明书一、施耐德变频器atv610说明书1.变频器是干什么的？主要用于驱动交流电动机，让交流电机实现无极调速。

例如用于送风机，用变频器来调节电机转速的快慢，就能改变送风量的大小。

还有很多需要调速的场合，用变频器来调速既简单又节能。

2.高、中、低、压变频器是多少伏的？高压变频器是3KV、6KV 或10KV的，如西门子罗宾康系列，安川的FSDrive-MV1S系列。

中压变频器是660V或1140V的，如ABB的AC5000，丹佛斯的FC200。

低压变频器是220V或380V的，如丹佛斯的FC102，FC360，FC51，西门子的MM440，V20。

二、施耐德变频器atv610说明书变频器的种类有那些？按变换的环节分类（1）交-直-交变频器，则是先把工频交流通过整流器变成直流，然后再把直流变换成频率电压可调的交流，又称间接式变频器，是目前广泛应用的通用型变频器。

（2）可分为交-交变频器，即将工频交流直接变换成频率电压可调的交流，又称直接式变频器；按直流电源性质分类（1）电压型变频器电压型变频器特点是中间直流环节的储能元件采用大电容，负载的无功功率将由它来缓冲，直流电压比较平稳，直流电源内阻较小，相当于电压源，故称电压型变频器，常选用于负载电压变化较大的场合。

（2）电流型变频器电流型变频器特点是中间直流环节采用大电感作为储能环节，缓冲无功功率，即扼制电流的变化，使电压接近正弦波，由于该直流内阻较大，故称电流源型变频器（电流型）。

电流型变频器的特点（优点）是能扼制负载电流频繁而急剧的变化。

常选用于负载电流变化较大的场合。

按主电路工作方法电压型变频器、电流型变频器按照工作原理分类可以分为V/f控制变频器、转差频率控制变频器和矢量控制变频器等；按照开关方式分类可以分为PAM控制变频器、PWM控制变频器和高载频PWM控制变频器；按照用途分类可以分为通用变频器、高性能专用变频器、高频变频器、单相变频器和三相变频器等。

D763-施耐德电气ATV61F变频器介绍

D763-施耐德电气ATV61F变频器介绍ATV6 ATV61F产品介绍驱策动力高质简约2012年 2012年9月14日 14日ATV61F目录ATV61F产品概述及定位 ATV61F产品特点 ATV61F跟ATV61有什么区别？有什么区别？商务政策=S= M&D MKT Vivian YaoATV61F 产品概况0.75-250kW电压等级110%/60s 4过电流能力 4种控制方式：矢量(SVC), 两点压频比(VF 2pt), 五点压频比(VF 5pt), UF平方(UF quad)55个主要特点基于成熟产品改进，稳定性与可靠性强全系标配EMC滤波器，降低对外干扰标配直流电抗器，大大减少谐波影响全系电路板加强涂层防护，应对恶劣环境提供多种基础选件，满足不同应用要求巴黎证券交易所上市–CAC403ATV61F 产品概况产品型号说明ATV61F H C16 N4 Z产品系列散热座 075 = 0.75 kWU22 = 2.2 kW D11 = 11kW C25 = 250kWN4=三相 -15%~380V … 415+10% V7段LED显示面板Schneider Electric- DT&S MKT- 2012.08ATV61F的行业应用水处理和污水处理水处理和污水处理增压泵增压泵提升泵取水泵污泥处理…… ? 恒压/无负压供负压供水泵厂恒压供水设备厂…… 暖通空调送风机循环水泵冷却水塔屋顶排风机…… 水泥风机……电厂空冷系统冷系统锅炉鼓风机炉鼓风机引风机循环泵…… 石油、石油、石化清水泵注油泵排污泵输油泵……热力供暖力供暖换热站……其他适用行业隧道与地道风机、道与地道风机、排水泵陶瓷机械窑炉风机陶瓷机械窑炉风机纺织机械风机纺织机械风机、水泵玻璃机械风机玻璃机械风机…… 械风机……ATV61F目录ATV61F产品概述及定位 ATV61F产品特点 ATV61F跟ATV61有什么区别？有什么区别？商务政策=S= M&D MKT Vivian Yao设计概览设计简明清晰通用性强可以提供选配的带中文菜单的图形显示终端。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

制动转矩 • 30 % 电机额定转矩，无制动电阻 (典型值) • 通过动态制动功能可以提高 • 带制动电阻 : – 可达130% Tn 与规格有关
路漫漫其悠远
2020/4/13
变频器典型应用
低压电 L1 L2
源
L3
断路器
接触器
线路电抗器
路漫漫其悠远
2020/4/13
制动电阻
T1 T2 T3
ATV61变频器产品介绍
路漫漫其悠远 2020/4/13
目录
I. 产品概述 II.基本特点
III.变频器应用
路漫漫其悠远
2020/4/13
ATV 61
ATV61
是针对工业变转矩而于2006年3月推出的一款高性能
变频器，主要替代ATV38以及ATV58和ATV68的变转矩应用场合;
功率等级：
人机交互友好：中文图形面板调试简单 simply start 安全功能，宏配置为泵应用内置的特别功能
多泵切换卡 (Controller inside) ... 全系列内置EMC滤波器， 18.5kW以上标配直流电抗器，提供更好的抑制
谐波方案。能量节约模式通讯：标配Modbus和CANopen两种协议
– 500 - 690V 三相, from 2.2 kW to 800 KW
– 200 - 240V 三相, from 0.75 kW to 90 kW (单相运行可以做到 5.5kW……)
路漫漫其悠远
Байду номын сангаас
2020/4/13
ATV 61
功率范围宽 0.75kW- 800kW • IP 54: <=90 kW
0.75KW ~ 800kW(IP54防护到90 kW)；
市场定位：
1、工业市场的风机和泵类； 2、 HVAC的高端市场。
路漫漫其悠远
2020/4/13
ATV 71
ATV71
是针对工业恒转矩应用而推出的一款高性能变频器，
主要替代ATV38以及ATV58和ATV68的恒转矩应用场合;
功率等级：0.37KW ~ 630kW；
• 所有工业总线＋智能楼宇总线协议
路漫漫其悠远
2020/4/13
ATV61的性能特点
最大瞬态电流 • 90KW 以下: 120% 变频器额定输出电流 60sec • 90KW以上 : 110% 变频器额定输出电流 60sec
瞬态过转矩 (+/-10%) • 130%电机额定转矩 60sec (与电机和变频器的规格有关)
电机电抗器
低压负载
市场定位：
工业市场的机械类负载。
路漫漫其悠远
2020/4/13
目录
I. 产品概述 II.基本特点
III.变频器应用
路漫漫其悠远
2020/4/13
ATV61基本特点
Altivar 61 覆盖电机功率范围从 0.75 kW 到 800 kW
– 380 - 480V 三相, from 0.75 kW to 630 KW