船舶工程专业英语词汇
有关船舶的英文专业术语
“Maritime Terminology: Essential Vocabulary for Ships”1.Bow: The front part of the ship.2.Stern: The back part of the ship.3.Port: The left side of the ship when facing forward.4.Starboard: The right side of the ship when facing forward.5.Hull: The main body of the ship, excluding superstructure and machinery.6.Deck: The horizontal surface of a ship where people walk or work.7.Bridge: The navigational control center of the ship, usually located at the front.8.Bulkhead: A partition wall within the hull of the ship.9.Keel: The central structural member of the ship’s hull, running along the bottom.10.Rudder: A movable device used to steer the ship.11.Propeller: A rotating device that propels the ship through the water.12.Mast: A vertical structure on the ship that supports sails or antennas.13.Bilge: The lowest compartment on a ship’s hull, often prone to collecting water and otherliquids.14.Ballast: Weight added to a ship to improve stability or adjust draft.15.Cargo Hold: A space within the ship’s hull for storing cargo.16.Anchor: A heavy object deployed to keep the ship stationary.17.Windlass: A machine used for raising and lowering the anchor.18.Lifeboat: A small boat carried by a ship for use in emergencies.19.Buoy: A floating object used for navigation or marking hazards.20.Chart: A map used for navigation, showing water depths, landmarks, and other relevantinformation.These are just a few examples of the many specialized terms used in the maritime industry. Understanding these terms is essential for effective communication and safe operation aboard ships.。
船舶专业英语
船舶专业的基本词汇1．基本，简单的词汇：AM 上午 PM下午Notification of inspection 检查验收通知单Application 申请，申请单Inspection 检验，报验Technical discussion 技术讨论On board 在船上In the workshop 在车间On the slipway 在船台上At pier(wharf) 在码头Fair 尚好的The performance is merely fair 性能尚好Terrible 极坏的，很糟的So so 马马虎虎So far ,so good 到目前，一切顺利Worse更糟的worst最差、最糟Improvement 改进Leave no room for improvement 完美，无缺点Accept 接收Accept subject to 有条件的接收，有待于……做好之后才接收Reject 拒收Comments 意见 defect lish 消除意见清单Item 项目memorandum 备忘录manual n、手册、说明书；a.手控的，手工的drawings 图纸working drawings 施工图finished drawings 完工图approved drawings 认可图drawings for approval 送审认可图supporting technical doucuments 基础技术文件sketch 草图 draw a sketch画草图up to the standard 达到标准substandard 低于标准的crane 吊车building berth 船台slipway 船台、下水滑道dry dock 干无坞pier 突码头、突堤wharf 码头along side (船)靠码头foreman 工长，领班coordinator 调度员inspector 检查员supervisor 管理人、监督人，监造人surveyor 验船师2、船体总体，及各类型船舶Hull 船体Forecastle 艏楼Stern 船尾Poop 艉楼Superstructure 上层建筑Foremast 前桅杆After mast 后桅杆Radar mast 雷达桅杆Main deck 主甲板Upper deck 上甲板Poop deck 艉楼甲板Accommodation deck 生活甲板Compass deck 罗经甲板Funnel 烟囱Bridge 桥楼，驾驶台Bridge wing 驾驶室翼桥Wheel house 驾驶室Engine room 机舱Engine control room 机舱集控室Catwalk 天桥、步桥Flying bridge （露天）航行驾驶室Rescue boat 救助艇Life boat 救生艇M/Vmerchant vessels 商船Naval Auxilary vessel 军用船Naval Ship/war shipd 军船Ice-breaker 破冰船Container vessel 集装箱船Oil tanker 油轮Products tanks 成品油轮Carrier 运输船、航空母舰、托架Chemical carrier 化学品运输船Liquefied gas carrier 液化气体船Liquefied natural gas carrier 液化天然气运输船Aircraft carrier/aeroplane carrier 航空母舰School ship/training ship 训练船Geophysical survey ship 地球物理勘探船Cruiser 巡洋舰、大型快船、游艇Canoe 独木船，皮舟Junk 平底中国帆船、舳板Gondola （意大利威尼斯的）一种狭长的平底船Yacht 快艇、游艇Fast boat 快艇Patrol boat 巡逻艇Anti-smuggling boat 缉私艇Torpedo boat 公安艇Ferry 渡船Catamaran 双体船Jet foil 喷水水翼艇Wing assrsted vessel 地效船3、各专业基本词汇1）船体：Draft forward 前吃水Draft middle 中吃水Draft after 后吃水Plimsoll mark/lineWaterline 吃水线Waterlines （型）水线Port 左舷Starboard 右舷Sagging 中垂、下垂、下挂（流）Hogging 中拱、上拱Derformation 变形Fairing 光顺、火工校正Hot work热工、明火作业section 分段、部分、剖面Block 分段Keel （船舶）龙骨Bilge keel 舭龙骨Power tool 带动力工具（风动或电动）Welder 电焊工Welding machine 电焊机A.C welding 交流（电弧）焊D.C welding 直流（电弧）焊Grinding 打磨Welding 电焊Spatters 飞溅（电焊）Under out 咬口Sharp edge 快口Deflection 挠曲，变形Slags 渣Welding slags 电焊渣Automatic welding 自动焊Manual welding 手工焊Arc welding 电弧焊Gas shielded welding气体保护焊Inter gas arc welding惰性气体保护电弧焊Welding seam焊缝Bending machine 弯曲机Three-roll bending machine三芯弯板机Torsional box抗扭箱Void space空舱Cofferdam 隔离舱Bulwark舷墙，防浪板Wall墙壁Floor地板Controllable pitch 可调桨Elastic coupling 弹性联轴节Bellow 波纹管Joint接头Gaskets垫片Fitting bolts 拂螺拴Chock 制动块、导缆器Chock fast 环氧垫块Foundation 底座、基座Mounting 装置、座、架Mount （常指火炮等武器的）座，架Vent pipe 透气管Sounding pipe探测管Vapour return line油气回路管Stripping line扫舱管Safety equipment 安全设备Life-saving equipment救生设备Cargo hold 货舱Cargo oil tank货油舱Cabin 船舱、舱室Room房间Store room储藏室Cold room冷库Fish room鱼库Meat room 肉库Provision room粮库Foam room 泡沫库CO2 room二氧化碳室Pump room泵室Battery room蓄电池室Radio room 报务室Galley 厨房Ventilation system 通风系统Fresh water piping system 淡水系统Sea water piping system 海水管系Water jacket水套Insulation materials绝缘材料Lagging绝缘材料、外套（锅炉、管子等）3）电器Current电流Voltage电压Frequency频率Contact触点、触头Ballast镇流器Convertor变频器、换能器Conductor导体Semi-conductor半导体Rectifier整流器Transformer变压器Thermostat 恒温器Thermister热敏器Edison base 螺丝灯座、爱迪生灯座Bayonet base卡口灯座On-off开关（量）Analogue模拟，模拟设备Active analogue有源模拟、主动模拟Passive analogue无源模拟、被动模拟Dry contact无源模拟、干接触Buzzer蜂鸣器Button按扭，电扭Switch开关Main switch主开关Main switch board主配电板Cable 电缆Wire 电线Three-core cable三蕊电缆Clamp夹钳、夹具Clip 接线柱、线夹Alligator clip鳄鱼夹、弹簧夹Voltage drop 电压降Speed droop速度降低Black out 黑灯试验Power failure失电Setting point 设定点Adjust 调正（v）Adjustment调正（n）Oscillator振荡器、振动器Oscilloprobe示波器测试头Oscilloscope示波器、示波仪Resistor电阻、电阻器Potentiometer电位器、电势计Electrolysis电解（作用）Electrolyte电解质、电解液setting point of power surplus负载余量设定值重载询问test the power surplus setting point重载询问试验4）漆、木Surface preparation表面处理（清理工作）Blasting equipment喷漆（砂粒）装置Sand blasting 喷砂除锈Pre-blasting预喷砂Lingt blasting 预喷砂Full blasting 通喷砂Sand sweep扫砂Sand blasting to SA2.5喷砂达到SA2.5级Steel work inspection after full blasting通喷砂后钢结构检查Cleanliness inspection清洁度检查Inspection after degreasing除去油脂后检查Removing oil stains by detergent/solvent使用洗洁剂/容剂除去油迹Shop primer 车间底漆Spray painting喷漆、喷涂法Touch-up 补漆、修正Touch-up painting补漆、点漆First coat 底漆、头道漆Finish coat 面漆Surface coat 表面涂层Under coat 内涂层Wearing coat 磨耗层Zinc-rich coating富锌涂层Cement wash coating（薄）水泥涂层Stripe coating 预涂层Floor covering 地板覆层Alkyd resin paint醇酸树脂漆Epoxy(resin-based)paint环氧树脂涂料Scuttle舷窗Carpet地毯Wooden skirt木裙板（踢脚）Aluminum skirt稆质裙板（踢脚）Brass nose装于楼梯踏步一的黄铜防滑镶条Stainless screw不锈钢螺钉Spring 弹簧Securing dev ice固定件Locking device闭锁装置，制动设备Plywood胶合板，层压板Laminated plate迭层板Laminate层压制品，迭层板，层压板High pressure washing of the hull用高压水冲洗船壳Steel plate temperature 钢板温度Condensation冷凝Capillary condensation毛细管现象Dew point露点Flashing point闪点Ignition point 燃点，着火点Ventilation for coating 涂装通风Dehumidifier去湿机，干燥机Dehumidification 去湿，去潮Sagging流挂，下垂Chalking粉化Peeling剥落（指油漆）Pinhole针孔CureCuring硬化，熟化，硫化Drying film thickness(DFT)干膜（漆膜）厚度Curing temperature硬化、固化温度Power tools有动力的工具（包括电动及风动）Pheomatic tools风动工具Burnt area烧坏的区域Oil stains油迹Scratches划痕Damaged places遭损坏的部位Chicken wire钢丝网Tiles瓷砖，瓦Mosaic-tile彩色瓷砖，镶嵌瓷砖，马赛克瓷砖Glue胶，粘结剂Silica硅石，二氧化碳Silicagel硅胶Decoration装饰，装修Interior decoration内部装饰，内装Deck head 天花板Ceiling天花板Paneling板墙，镶板Wall墙壁Desk书桌，桌台Drawer 抽屉Catch hook固定钩子Observation window 观察窗Inspection window检查孔窗Clear view window旋转观察窗Curtain 窗帘Latch止动销，插销Valance窗帘箱Hanging窗帘Eyebrow舷窗眉板Pre-alarm预报警Trip脱扣，跳闸Preferential trip优先脱扣Transducer换能器synchronize（便）同步synchronize motor同步电机synchronous motor异步电机step motor步进电机diode二极管triode三极管audion三极管single phase单相three phase三相phase-in逐步引进phase-shafting相移retarding phase 滞后相位reversed phase倒相，相反relay继电器timer定时器trimmer微调电容器，调正片delay延时carrier载波，载波电流transponder发射器，应答器，询问机echo-sound回声测深仪radio navigation equipment无线电导航设备log计程仪auto-pilot自动驾驶仪gyro-compass电罗经barrier屏障，障碍，栅栏zenner barrier齐纳屏（使电只能单向流的半导体）radio beacon无线电信标pluse脉冲blanking plus 消隐脉冲induction感应，感应现象oscillation振荡Leak(v)渗，漏Leakage(n) 渗，漏Overhaul大修，彻底检修Hammer榔头Spanner扳手，扳头Ring spanner环形扳手，梅花扳手Allen key 内六角扳手，Box spanner套筒扳手Torque spanner扭力扳手Double-ended spanner双头扳手Monkey spanner活络扳手，活络管扳手Shifting spanner活络扳手Pipe spanner管子扳手Reamer铰刀Reaming （用）铰（刀扩）孔Countersink reamer锥形孔铰刀Wrench扳手，扳头Shisel凿子Calipers卡钳，两脚规Inside calipers内卡钳Bore 内孔Boroscopic inspection内孔表面检查Boroscope内孔表面检查仪Plug塞（子），（内燃机）火花塞Cock施塞，龙头Valve阀P/V valve P/V阀Strainer滤器Coarse strainer粗滤器Fine strainer精滤器Oil separator分油机Back pressure背压Pressure test压力试验Over speed 超速Over load超负荷Dafety device 安全装置Fly wheel飞轮Floating floor 浮式地板Deckhead 天花板（指由甲板形成的）Ladder 梯子Vertical ladder直梯Inclined ladder斜梯Accommodation ladder舷梯Pilot ladder引水员；软梯2)轮机Centering对中心Alignment对准，对准中心Inspection报验Installation安装Final inspection of M/E insallation主机最终安装报验Inspection of the centering of the stern tabe before fine boring 精镗前艉轴管中心校准Alignment check/inspection拉中心/校正报验Completeness inspection of the thermal oil circulating piping system 热油循环管系完整性报验Cleanliness inspection after flushing F.O piping system燃油管串油后清洁检查Function test of steering gear舵机效甩试验Hose test of water tight doors水密门冲水试验Noise lever measurement噪声测量Vibration level measurement 振动测量Main engine (M/E)主机Generator发电机Emergency generator应急发电机Shaft generator轴带发电机Fresh water generator 制淡装置Steering gear 舵机General service pump总用泵Pire pump消防泵Hydraulic motor 液压马达Hydraulic nuts液压螺帽Rudder舵Rudder bl ade舵叶Propeller车叶，螺旋桨Fixed pitch propeller固定螺距的螺旋桨Lofting型线图放样Lay off（船及部件）放样，下料Plate-cutting钢板下料，开工Numerically-controlled cutting machine数控切割机Cutting machine切割机Under water plasma cutting machine水下等离子切割机Surface preparation表面处理Fabrication（焊）开坡口，边缘加工（如刨边）Upside down construction method分段装配Assembly 反身建法Erection装配，大合拢Jig装配架，胎架Bow jip 船首部胎架Girder纵向构件，桁（材）Beam梁，横梁Sections型材Profile型钢（条）Bar 杆，棒,棒材Plate板材Angle bar角钢I beam（窄缘）工字梁H beam（宽缘）工字梁Stiffener扶强材Bracket托架，支架，肘板Support 支架Frame肋骨，框架Douler复板Coaming（舱口）围板，缘材Sinp剪切Cut切割Anchor锚Anchor widdlass 锚机Anchorage锚位，锚地Chain链Chain block链条滑车，神仙滑车Platform平台Crossover跨越（梯桥），立交Life raft 救身筏Life buoy 救生圈Forward winch 前绞缆机After winch 后绞缆机Windlass锚机Bitt带缆桩，系桩Fairlead导缆钳，导缆孔Hand rail扶手，栏杆Beam横梁Frame肋骨，框架Scantling构件尺寸Cargo oil tank货油舱Scantling draft结构吃水Forepeak tank首尖舱After peak tank尾尖舱Water ballast tanks(W.B.T)压载水舱Fuel oil tank(F.O.T)燃油舱Lubricating oil tank(L.OT)滑油舱Diesel oil tank(D.O.T)柴油舱Double botton双层底Double skin双层外板，双层蒙皮Bow thruster艏侧推Propeller车叶Fixed pitch propeller定螺距螺旋桨Controllable pitch propeller(CPP)可调螺距螺旋桨Shaft轴Tail shart尾轴Shaft generator轴带发电机Watertight doors水密门Bulwark舷墙Bulkhead舱壁Tank top内底，液舱顶Hatch cover舱口盖Manhole人孔Fin stablizer减摇鳍Antifouling system防海生物的，防污染系统Ship船Vessel船，舰Fabrication制造，分段装配（precfabrication预制，预加工）Assemble装配，组装Erection大合拢，船台装配Staging脚手架Block stage分段阶段Mile stone（里程碑，大节点）Plate-cutting下料，开工Keel-laying上船台，龙骨铺设Lauching下水mooring trial码头试验，系泊试验sea trial(sea)试航delivery of the ship交船defect list by the owner/society船东提出的消除意见清单/船级社提出的消除意见清单design stage设计阶段submit drawings to owner,classification society(LR、DNV、BV、ABS，etc)for approval向船东，船级社（劳氏，挪威，法国，美国等）提交认可图纸hull workshop船体车间machining workshop金工车间machinery engineering workshop轮机车间electrical workshop电气车间business dept.经营处perchasing dept.供应处Q.C.Dept.检验处Design dept.设计室Painting and carpenter’s workshop漆木车间Project manager项目经理Director指导者，厂长，董事Managing director执行董事，常务董事，总经理Head首长，团长，主任Manager经理，管理人，干事Leader领导者Meeting会议Negotiation谈判Agreement协议Shipyard船厂。
船舶工程名词术语
1 sea keeping performance 耐波性能2 maneuverability 操纵性3 endurance 续航力，全功率工作时间4 cargo handling 货物装载5 subdivision 分舱6 stability 稳性7 freeboard 干舷8 tonnage 吨位9 basic design 基本设计10 concept design 概念设计11 preliminary design 初步设计12 contract design 合同设计13 design spiral 设计螺旋循环方式14 bidder 投标人15 iterative process 迭代过程16 naval architecture 造船学17 feasibility study 可行性研究18 beam 船宽，梁19 depth 船深20 draft 吃水21 fullness 丰满度22 cargo cubic 货舱舱容，载货容积23 deadweight 总载重量（吨）24 talking paper 讨论文件25 light-ship 空船26 a faired set of lines 经过光顺处理的一套型线27 hull form 船形，船体外形28 frame 船肋骨，框架，桁架29 fresh water 淡水30 living and utility spaces 居住与公用舱室31 outfit 舾装32 trial 实船试验33 major ship 大型船舶34 detail design 详细设计35 ship fitter 船舶装配工36 welder 焊工37 metal worker 金属工38 machinery vendor 机械（主机）卖方39 outfitter 舾装工40 pipe fitter 管装工41 artisan 技工42 shipyard 船厂43 break bulk 件杂货44 containerized 集装箱化45 liner trade 定期班轮营运业46 tanker 油船47 bulk carrier 散装货船48 offshore drilling 离岸钻井49 drilling rig 钻架50 pipe laying barge （海底）铺管驳船51 fleets of vessels 船队52 outboard profile 侧视图53 inboard profile 纵剖面图54 general arrangement 总布置图55 hold 船舱56 crew quarters 船员居住舱57 commissary spaces 补给库舱室，粮食库58 lines 型线59 plan views 设计图60 midship section 舯横剖面61 elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔62 sections 剖面，横剖面63 main shafting 主轴系64 power and lighting system 动力与照明系统65 diagram 图，原理图，设计图，流程图66 ventilation and air conditioningdiagram 通风与空调敷设设计图67 normal operating condition 常规（正常）运作状况68 capacity plan 舱容图69 curves of form 各船型曲线70 floodable length curve 可浸长度曲线71 trim 纵倾72 damage stability 破损稳性73 naval architect 造船师74 naval architecture 造船工程75 categorize 分类76 aerostatic 空气静力学的77 self-induced 自身诱导的78 cushion of air 气垫79 lift fan 升力风扇80 skirt （气垫船）围裙81 air cushion vehicle 气垫船82 amphibious 两栖的83 rigid side walls 刚性侧壁84 captured-air-bubble vehicle 束缚气泡减阻船85 supper cavitating propeller 超空泡螺旋桨86 ferry 渡轮，渡口，渡运航线87 cross-channel automobileferries 横越海峡车客渡轮88 polar-exploration craft 极地考察船89 landing craft 登陆艇90 riverine warfare vessel 内河舰艇91 hydrodynamic 水动力学的92 flow pattern 流型，流线谱93 airfoil 气翼，翼剖面，机面，方向舵94 hydrofoil 水翼95 surface piercing 穿透水面的96 strut 支柱，支撑构性97 planing hull 滑行船体98 V-section V型剖面99 deep V hull 深V型船体100 rough sea 汹涌的海浪101 buoyant 浮力的102 displacement 排水量103 common carrier 通用运输船104 trawling 拖网105 crussing range 航程106 seaworthness 适航性107 bulk oil carrier 散装油轮108 tanker 油轮109 supertanker 超级油轮110 LCC（Large Crude Carrier）大型原油轮（载重10～20万吨）111 VLCC（Very Large Crude Carrier）巨型（原）油轮（载重量>20万吨）112 ULCC（Ultra Large Crude Carrier）超级大型（原）油轮（载重量>40万吨）113 SWATH（Small Waterplane Area Twin Hull）小水线面双体船114 multihull vessel 多体船115 catamaran 双体船116 trimaran 三体船117 launch 发射，下水118 launching equipment （向水中）投放设备119 configuration 安排，构型，配置120 submersible 潜器121 endurance 续航力122 payload 有效载荷123 merchant ship 商船124 survivability 生存力125 babitability 适居性126 commercial ship 营利用船127 freight rate 运费率128 life-cycle cost 生命周期成本129 acquisition cost 购置（获取）成本130 pleasure ship 游乐用船131 naval ship 军船132 liner 定期航班船133 tugboat 拖船134 hostile sea 凶险的波浪135 oil-rig 钻井架136 roll-on/ro-off（Ro-Ro）滚装137 aircraft carrier 航空母舰138 guided-missile cruiser 导弹巡洋舰139 destroyer 驱逐舰140 at-sea replenishment 海上补给141 reenlistment 重征服役142 icebreaker 破冰船143 Coast Guard cutte （美国）海岸警备队快艇144 principal dimensions 主尺度145 perpendicular （船艏、艉）柱，垂直的，正交的146 forward/after perpendicular 艏/艉柱147 length between Perpendicular 两柱间长148 stem 船艏149 summer load water line 夏季载重水线150 rudder post 舵柱151 pintle 销，枢轴152 dock 泊靠153 length overall 总长154 overhang 外悬155 stern 艉156 rake 倾斜157 bulbous bow 球鼻艏158 trim 纵倾159 amidships 舯160 breadth moulded 型宽161 breadth extreme 最大宽，计算宽度162 shell planting 船壳板163 fender 护舷164 quay （横）码头，停泊所165 depth 船深166 rounded gunwale （修圆的舷边）167 sheer （甲板）舷弧168 sheer forward 艏舷弧169 sheer aft 艉舷弧170 deck line at side 甲板边线171 camber 梁拱172 drainage 排（泄）水173 rise of floor 底升174 bilge 舭，舱底175 flat of keel 平板龙骨176 rivet 铆接，铆钉177 girder 桁梁，桁架178 bevel 折角179 bar 型材，材180 tumble home （船侧）内倾181 seakeeping 适航性182 base line 基线183 trim by the stern/bow 艏/艉倾184 bar keel 棒龙骨，方龙骨，矩形龙骨185 draught（=draft）吃水，草图，设计图，牵引力186 imperial unit 英制单位187 metric unit 公制单位188 hog 中拱189 sag 中垂190 dry dock 干船坞191 freeboard 干舷192 weather deck 露天甲板193 seaworthness 适航性194 Load Line Regulations 载重线公约、规范195 sheer profile 纵剖线196 accommodation 居住（舱室）197 bilge radius 舭半径198 reserve buoyancy 储备浮力199 heel 横倾200 Superstructure 上层建筑201 deckhouse 舱面室，甲板室202 surmount 顶上覆盖，越过203 middle line plane 中线面204 sheer plane 水线面205 keel 龙骨206 transverse section 横剖面207 orthogonal 正交的，矩形的208 body plan 横剖面图209 by convention 按照惯例，按约定210 half breadth plan 半宽图211 lines plan 型线图212 sheer drawing 剖面图213 load waterplane 载重水线面214 slice 一部分，薄片215 intersection 交点，交叉，横断（切）216 fore/aft perpendicular 艏/艉柱217 vicinity 邻近，附近218 length between perpendiculars 垂线间长219 maximum beam amidships 舯最大宽220 tumble home 内倾221 flare 外飘，外张222 rake 倾斜，倾斜度，倾斜角223 conspicuous 显著的，值得注意的224 funnel 烟囱225 deck camber 甲板梁拱226 concave 凹，凹的，拱形的227 mast 桅杆228 stem contour 艏柱型线229 heel 横倾230 yaw 艏摇231 drift 漂移，偏航232 Bonjean curve 邦戎曲线233 conceive 设想，想象234 impression 模槽，型腔，印痕，印象235 appendage 附体236 abaft 朝向船尾237 rudder 舵238 bilge 舭239 circumscribe 外接，外切240 rectangle 矩形241 yacht 快艇242 midship section coefficient 舯横剖面系数243 block coefficient 方形系数244 longitudinal prismatic coefficient 纵向菱形系数245 vertical prismatic coefficient 垂向菱形系数246 cross-sectional area 横剖面面积247 Lloyd’s Rules 劳埃德（船级社）规范248 adopt 采用249 principal dimensions 主尺度250 length overall 总长251 port 左舷252 starboard 右舷253 freeboard 干舷254 beam 船身最大宽，横梁255 girder 桁，梁256 chine 舭，舷，脊257 soft chine 圆舭258 hard chine 尖舭259 transom（stern）方尾260 cruiser stern 巡洋舰尾261 ship form 船型262 lines plan 型线图263 orthogonal 正交的264 body section 横剖图265 division 站，划分，分隔266 base, base line 基线267 water line 水线268 sheer profile 纵剖图269 buttock 后体纵剖线270 bow line 前体纵剖线271 fair 光顺272 offsets 型值273 lift offsets 量取型值274 （to）run the waterlines 绘制水线275 batten 压条276 drawing office 绘图室277 scale 缩尺，尺度，尺278 mould loft 放样间279 shipyard 船厂280 full scale 全尺度281 loft floor 放样台282 contracted scale 缩尺283 mark out 划线，划记号284 pin 钉，销285 moulded line 型线286 in strake 内列板287 out strake 外列板288 in way of…在……处289 wing shaft 侧轴290 shaft bossing 轴包套291 stiffen 加劲，加强292 frame 框架，肋骨293 shaft bracket 轴支架294 appendage 附件，附体295 cross section 横剖面296 amidships 在舯部，舯297 parallel middle body 平行中体298 fine fast ship 纤细（细长）高速船299 abaft 朝船尾300 entrance 进流段301 run 去流段302 forward/after shoulder 前/后肩303 buoyancy 浮力304 load waterline 载重水险305 from coefficient 船形系数306 block coefficient 方形系数307 bulk carrier 散装货船308 prismatic coefficient 菱形系数309 immerse 浸入，浸没310 circumsection 外切311 midship area coefficient 舯横剖面系数312 waterplane area coefficient 水线面积系数313 prism 棱柱体314 vertical prismatic coefficient 垂向菱形系数315 U-form U型316 V-shaped V形的317 full form 丰满船型318 fine form 瘦长（细长）船型319 classification society 船级社320 governmental authorities 政府当局，管理机构321 ship owner 船东322 underwriter 货主323 risk （海运）保险商324 Lloyd’s Register of shipping （英国）劳埃德船级社325 Department of Trade （英国）贸易部326 Board of Trade （英国）贸易厅327 standard 规章328 supervision of the society’s surveyor 船级社验船师的监造书329 Lloyd’s machinery certificate （LMC）劳埃德（船舶）机械证书330 register （船舶）登录簿，船名录331 fire protection, detection and extinction 防火，探火与灭火332 liquefied gas carrier 液化气运输船333 Green Book （船级社）绿皮书，（19世纪英国另一船级社的船名录，现合并于劳埃德船级社，用于登陆快速远洋船）334 ton gross= gross ton 长吨=1.016公吨335 dredge 挖泥船336 hopper barge （自动）倾卸板337 scantling 材积338 casualty 事故，死伤，灾难339 corrosion 锈蚀，腐蚀340 Bureau Veritas （法国）船级社341 American Bureau Shipping （美国）船级社342 Germanischer Lloyd （德国）劳埃德船级社343 Registo Italiano Navade （意大利）船级社344 International Association of Classification Society （IACS）国际船级社联合会345 to vet proposals 审查新建议346 legislation 立法347 Merchant Shipping Acts 商业运输法348 life saving appliance 救生设备349 carriage of grain cargoes 谷类货物运输机350 introduces a bill 提出一项议案351 Plimsoll line 普林索尔载重线352 reserve buoyancy 储备浮力353 freeboard deck 干舷甲板354 athwart ships （船）横向355 Type A ship A类船356 gasketed openings 装以密封垫的开口357 compartment 舱室358 tabular freeboard 列成表格的干舷船359 Suez Canal tonnage 苏伊士运河吨位限制360 Panama Canal 巴拿马运河361 Stringent safety regulations 严格的安全规章362 maritime 海事的，海运的，靠海的，延海的363 titanic 巨大的364 the Titanic 泰坦尼克号365 maiden voyage 处女航366 flood 进水，泛滥367 Inter-national Convention for the Safety of Life at Sea（ICSOLAS）海上生命安全性国际公约368 permanent body 永久性组织机构369 aegis 保护，庇护370 Inter-governmental Maritime Consultive Organization（IMCO）国际政府间海事质询组织371 The Register of Shipping of the People’s Republic of China中国船舶检验局372 static equilibrium 静平衡373 neutral equilibrium 中性平衡374 upright position 正浮位置375 homogeneous cylinder 均质柱状体376 capsize 倾覆377 resultant 合力378 couple 力矩，力偶379 positive righting moment 正扶正力矩380 righting arm 扶正力臂，恢复力臂381 capsizing moment 倾覆力矩382 met center 稳心383 list 倾斜，倾侧384 stable equilibrium 稳定平衡385 criterion 判据，准则386 overall stability 总体稳性387 initial stability at small angle of inclination 小倾角初稳性388 met centric height 稳心高389 off-center loading 偏离中心的装载390 port 左舷391 starboard 右舷392 lighter 港驳船393 watertight integrity 水密完整性394 crucial element 重要因素395 intact stability 完整稳性396 barge 驳船397 ship hydrodynamics 船舶水动力学398 transverse stability 横稳性399 appendage 附体400 frictional resistance 摩擦阻力401 eddy 旋涡402 gradient 梯度403 wetted surface 湿表面积404 Reynolds number 雷诺数405 wave-making resistance 兴波阻力406 eddy-making resistance 旋涡阻力407 extrapolate 外插408 residuary resistance 剩余阻力409 speed-to-length ratio 速长比410 nautical mile 海里411 bow wave 艏波412 wave pattern 波型413 stern wave 艉波414 fair 光顺415 hole 水（流）深凹处416 mid-body （船）中体417 shoulder 船肩418 crest（of wave）波峰419 trough 波谷420 bulb 球鼻首421 bracket 轴支架，支架422 buoyancy 浮力423 viscosity 粘性424 streamline 流线425 curvature 曲率426 paddle 桨427 oar 橹；桨428 paddle-wheel-propelled 明轮推进的429 Admiralty 海军部，海军上将430 barge 驳船431 double-acting steam cylinder 双向作用的一、船舶种类1、一般ship, vessel 船舶，船warship 舰boat, craft 艇raft, float 筏naval ship 军用船civil ship, merchant ship 民用船2、战斗舰艇combatant ship 战斗舰艇，军舰surface combatant ship 水面战斗舰艇aircraft carrier 航空母舰attack aircraft carrier 攻击航空母舰antisubmarine aircraft carrier 反潜航空母舰helicopter carrier 直升机母舰cruiser 巡洋舰guided missile cruiser 导弹巡洋舰destroyer 驱逐舰guided missile destroyer 导弹驱逐舰frigate 护卫舰guided missile frigate 导弹护卫舰antisubmarine frigate 反潜护卫舰minelayer 布雷舰guided missile boat 导弹艇torpedo boat 鱼雷艇submarine chaser 猎潜艇gun boat 炮艇landing ship 登陆舰dock landing ship 坞式登陆舰landing craft 登陆艇minesweeper 扫雷舰minesweeper, minesweeping boat 扫雷艇remote control minesweeper 遥控扫雷艇submarine 潜艇guided missile submarine 导弹潜艇ballistic missile submarine 弹道导弹潜艇cruising missile submarine 飞航导弹潜艇torpedo submarine 鱼雷潜艇nuclear-powered submarine 核潜艇conventionally-powered submarine 常规潜艇3、辅助舰船auxiliary ship 辅助舰船repair ship 修理舰training ship 训练舰tender, depot ship 供应舰replenishment ship 补给舰scout ship, reconnaissance ship 侦察船target vessel 靶船remote control target boat 遥控靶艇torpedo recovery vessel 捞雷船degaussing ship, demagnetizing ship 消磁船hospital ship 医院船research ship, test vessel 研究试验船instrumented tracking and telemetry ship 跟踪遥测船underwater acoustics research ship 水声试验船patrol boat 巡逻艇bridge boat, pontoon raft 浮桥舟4、运输船transport ship 运输船passenger ship 客船passenger cargo vessel 客货船cargo ship, freight vessel 货船dry cargo ship 干货船bulk cargo carrier 散货船bulk grain carrier 散粮船cement carrier 散装水泥船collier, coal carrier 运煤船ore carrier 矿砂船dual-purpose carrier, oil and bulk carrier, oil and ore carrier 两用散货船triple-purpose carrier, oil-bulk and ore carrier 三用散货船general cargo ship 杂货船liquid cargo ship 液货船oil tanker, tanker 油船liquid chemical tanker 液体化学品船liquefied（liquified）natural gas carrier 液化天然气船refrigerated ship, cold storage ship 冷藏船fruit carrier 运水果船meat carrier 运肉船container ship 集装箱船full container ship 全集装箱船semi-container ship 半集装箱船roll-on/roll-off ship, drive-on/drive-off ship 滚装船barge carrier, lighter aboard ship 载驳船automobile carrier 运汽车船timber carrier 运木船cattle carrier 牲畜船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船train ferry 列车渡船automobile ferry 汽车渡船barge, lighter 驳船passenger barge 客驳freight barge, cargo barge 货驳integrated barge 分节驳large opening barge 舱口驳open barge 敞舱驳covered barge, deck barge 甲板驳well-deck barge 半舱驳5、工程船working ship 工程船ocean development ship 海洋开发船self-elevating drilling platform 自升式钻井平台jack-up self-elevating drilling platform 桩腿自升式钻井平台shoe self-elevating drilling platform 桩靴自升式钻井平台mat self-elevating drilling platform 沉垫自升式钻井平台bottom supporting drilling platform 定柱沉垫式钻井平台floating drilling rig 浮式钻井装置semi-submersible drilling rig 半潜式钻井装置drilling ship 钻井船center-mooring drilling ship 中心锚泊钻井船drilling barge 钻井驳船swamp drilling barge 沼泽地钻井驳船drilling tender 钻井辅助船dredger 挖泥船suction dredger 扬吸挖泥船trailing suction hopper dredger 耙吸式挖泥船cutter suction dredger 绞吸式挖泥船dustpan suction dredger 冲吸式挖泥船jet lift dredger 喷射挖泥船bucket dredger 链斗挖泥船sand pump bucket dredger 自扬链斗挖泥船overhead bucket dredger 高架链斗挖泥船self-propelled bucket dredger 自航链斗挖泥船grab dredger 抓斗挖泥船self-propelled grab hopper dredger 自航抓斗挖泥船dipper dredger 铲斗挖泥船amphi dredger 两栖挖泥船mud lighter 泥驳elevater barge 封底泥驳hopper barge 开底泥驳side hopper barge 侧开泥驳split type dump hopper barge 对开泥驳floating crane, derrick boat 起重船slew type floating crane 转机式起重船fixed type floating crane 定机式起重船luff type floating crane 定机变幅式起重船floating pile driver piler 打桩船floating sand piler 砂桩打桩船floating pile presser 压桩船layer 布设船danlayer, buoy（age）vessel 布标船dan boat 航标工作船cable layer, cable ship 布缆船pipelaying barge, pipeline layer 铺管船bury barge 埋管船salvage and rescue ship 打捞救生船salvage and rescue ship 救捞船salvage barge 救捞驳船rescue tug 救助拖船rescue ship 救生船submarine rescue vessel 援潜救生船high speed life boat 救生快艇deep submergence rescue vehicle 深潜救生艇floating dock 浮船坞single unit floating dock 整体式浮船坞pontoon floating dock 浮箱式浮船坞three-piece type floating dock 三段式浮船坞integrated floating dock 组合式浮船坞surveying ship 测量船ice-breaker 破冰船sweeper 扫海船underwater drilling and blasting ship 炸礁船rock crusher 碎石船light boat 灯标船barge unloading suction dredger 吹泥船floating booster stating 接力泵船drilling ship 钻探船stone dumper 抛石船floating concrete mixer 混凝土搅拌船diving vessel, divers boat 潜水工作船generating ship 电站船repair ship 修理船distilling ship 海水淡化船dredger 采矿船gold dredger 采金船anchor boat 起锚船floating living quarter 住宿船self-elevating platforms for civil engineering 水上施工平台6、渔业船fisheries 渔业船fisheries guidance ship 渔业指导船fisheries administration ship 鱼政船fisheries inspection boat 渔业监督船fisheries rescue ship 渔业救助船fisheries rescue ship 渔船trawler 拖网渔船bull trawler 对拖网渔船single trawler 单拖网渔船stern ramp trawler 尾滑道拖网渔船seine netter 围网渔船gill netter 刺网渔船square netter 敷网渔船line fishing boat, liner 钓渔船pole and line fishing boat 竿钓渔船trolling boat, troller 拖钓渔船long liner 延绳钓渔船squid angling boat 鱿鱼钓渔船fishing sailer 风帆渔船fishing motor sailer 机帆渔船whaling ship 捕鲸船combination fishing vessel 多种作业渔船pearl boat 海珍品采集船fisheries auxiliary vessel 渔业辅助船fishery mother ship 渔业基地船fish factory ship 渔业加工船whale factory ship 捕鲸母船fisheries tender 渔业补给船buy boat 收鲜船refrigerated seawater fish carrier冷海水保险运输船live fish carrier 活鱼运输船fish luring light boat, lurker 诱鱼灯船二、船舶总布置1、一般ships general arrangement 船舶总布置interior arrangement 舱室布置arrangement of shipboard weapons 武备布置stairway and passageway arrangement 梯道布置engine room arrangement 机舱布置shafting arrangement 轴系布置compartment 舱space 舱室2、甲板、平台、通道bridge deck 驾驶甲板compass deck 罗经甲板boat deck 艇甲板promenade deck 游步甲板accommodation deck 起居甲板vehicle deck 车辆甲板flight deck 飞行甲板angled deck 斜角甲板helicopter deck 直升机甲板hangar deck 机库甲板tank deck 坦克甲板winch platform 起货甲板gun platform 火炮甲板passage passageway 通道interior passageway 内通道exterior passageway 外通道3、工作和设备舱室wheel house 驾驶室chart room 海图室coding room 译电室radio room 报务室spare radio room 备用报务室radar room 雷达室sonar control room 声纳室combat information center 情报中心fire director room, weapon control room 指挥仪室main engine room 主机舱main engine control room 主机操纵室auxiliary engine room 辅机舱reactor room 反应堆舱boiler room 锅炉舱engine and boiler room 机炉舱reduction gear room 减速器舱steering engine room 舵机舱fan room 通风机舱commutator room 变流机舱air-conditioning unit room 空调室emergency generator room 应急发电机室refrigerator room 冷冻机室fire-smothering unit room 灭火装置室battery room 蓄电池室gyro-compass room 陀螺罗经室log room 计程仪室missile magazine 导弹舱magazine 弹药舱depth charge magazine 深弹舱depth charge rack room 深弹滚架舱ammunition lobby 弹药运转间sonar transducer room 声纳舱workshop 机修间electrician’s store 电工间carpenter’s store 木工间chain locker 锚链舱mast house 桅室decontamination room 洗消室4、生活舱室living accommodation 生活舱室living accommodation 居住舱室captain’s room 船长室crew’s room 船员室cabin 客舱political commissar’s room 政委室political officer’s room 政委室group commander’s room 编队指挥员室captain’s room 舰长室vice captain’s room 副长室officer’s room 干部室crew’s accommodation 士兵舱5、货舱cargo hold 货舱cargo oil tank 货油舱container hold 集装箱舱refrigerated cargo hold 冷藏货舱liquified natural gas tank 液化天然气舱mail room 邮件舱luggage room 行李舱vehicle hold 汽车舱6、液舱liquid tank 液舱fuel oil tank 燃油舱lubricating oil tank 滑油舱overflow fuel oil tank 燃油溢油舱overflow lubricating oil tank 滑油溢油舱fuel oil sump tank 污燃油舱lubricating oil sump tank 污滑油舱circulating lubricating oil tank 循环滑油舱ballast water tank 压载水舱fresh water tank 淡水舱distilled-water tank 蒸馏水舱feed water tank 锅炉水舱stabilizing tank , anti-rolling tank 减摇水舱bilge tank 污水舱7、贮藏室store 贮藏室awning store 天幕贮藏室lamp store 灯具贮藏室hawser store 帆缆间paint store 油漆间provision store 粮食库refrigerating chamber 冷藏库8、其他fore peak 首尖舱after peak 尾尖舱bottom side tank 底边舱top side tank 顶边舱wing tank 边舱lower hold 底舱double-bottom compartment 双层底舱cofferdam 隔离空舱command station 总指挥所secondary command station 预备指挥所三、船体几何形状和尺度1、一般molded hull surface 船体型表面ship’s form, hull form 船体线型molded volume, volume of molded form 型排水体积bare hull, naked hull 裸船体appendages 附体2、基准面和基准线principal coordinate planes 主坐标平面base plane 基平面center（-line）plane, central longitudinal plane, longitudinal middle（-line）plane 中线面midstation plane 中站面molded base line 基线3、船体尺度principal dimensions 主尺度length overall, overall length 总长extreme length 最大长length between perpendiculars 垂线间长length overall submerged 浸体长waterline length 水线长designed waterline length 设计水线长load waterline length 满载水线长molded breadth 型宽waterline breadth 水线宽designed waterline breadth 设计水线宽extreme breadth 最大宽breadth overall submerged 浸体宽molded depth 型深draft 吃水molded draft 型吃水keel draft 龙骨吃水designed draft 设计吃水fore draft 首吃水aft draft 尾吃水mean draft 平均吃水navigational draft 外形吃水loaded draft 满载吃水light draft 空载吃水draft mark 吃水标志4、型线图与几何形状lines plan 型线图body plan 横剖面图sheer plan 纵剖面图half breadth plan 半宽水线图forward perpendicular 首垂线after perpendicular 尾垂线grid 格子线ordinate station 站midstation 中站station ordinates 站线molded lines 型线mathematical lines 数学型线offsets 型值preliminary offsets 原始型值returned offsets, finished offsets 完工型值table of offsets 型值表preliminary table of offsets 原始型值表returned table of offsets, finished table of offsets 完工型值表transverse sections 横剖面midship section, amidship section 中横剖面maximum section, fullest section 最大横剖面waterplane 水线面buttocks 纵剖线body lines 横剖线diagonal 斜剖线bilge diagonal 舭斜剖线profile 外廓线waterline 水线designed waterline 设计水线loaded waterline 满载水线parallel middle-body length 平行中体长length of entrance 进流段长length of run 去流段长half angle of entrance 半进流角deck line 甲板线deck line at side, deck side line 甲板边线deck line at center, deck center line 甲板中线sheer line 舷弧线molded depth line 舷弧基准线sheer 舷弧sheer at forward perpendicular 首舷弧sheer at after perpendicular 尾舷弧average sheer, mean sheer 平均舷弧sheer at deck center 脊弧camber, round of beam 梁拱camber curve 梁拱线deadrise, rise of floor, rise of bottom 舭部升高bilge radius 舭部半径keel line 龙骨线rake of keel, keel rake, designed drag, keel drag 龙骨设计斜度half-siding 龙骨水平半宽floor line 船底斜升线knuckle line 折角线tumble home 内倾flare 外倾flare 外飘immersed transom beam 方尾浸宽immersed transom draft 方尾浸深5、船型系数与尺度比coefficients of form 船型系数block coefficient 方形系数prismatic coefficient longitudinal coefficient, cylindrical coefficient 棱形系数vertical prismatic coefficient 垂向棱形系数waterline coefficient waterplane coefficient 水线面系数midship section coefficient 中横剖面系数length breadth ratio 长宽比length depth ratio 长深比breadth depth ratio 宽深比breadth draft ratio 宽度吃水比draft depth ratio 吃水型深比6、船体各部位fore body 前体after body 后体parallel waterline 水线平行段waterline beginning 水线前段waterline ending 水线后段parallel middle body 平行中体entrance 进流段run 去流段shoulder 肩forward shoulder 前肩after shoulder 后肩bilge 舭soft chine 圆舭hard chine 尖舭transom 方尾端面overhang 悬伸部counter 尾伸部forefoot 首踵aftfoot 尾踵bossing, shaft bossing, shell bossing 轴包套short bossing 短轴包套long bossing 长轴包套deadwood 尾鳍7、船的首、尾及剖面型式clipper bow, fiddle bow, cutwater bow, knee bow, overhanging bow 飞剪型首raked bow 前倾型首vertical bow 直立型首icebreaker bow 破冰型首bulbous bow, bulb bow 球鼻型首elliptical stern 椭圆型尾transom stern 方型尾cruiser stern 巡洋舰型尾tunnel stern 隧道型尾bulb section 球臌型剖面U-shaped section U型剖面V-shaped section V型剖面四、船舶重量和容积量度1、排水量与重量displacement 排水量molded displacement 型排水量total displacement 总排水量light displacement, light weight 空载排水量light weight （or mass）, light displacement 空船重量（或质量）standard displacement 标准排水量normal displacement 正常排水量full load displacement,loaded displacement 满载排水量maximum displacement 最大排水量designed displacement 设计排水量displacement margin 储备排水量total deadweight, gross deadweight 载重量cargo deadweight, net capacity, useful. deadweight 净载重量deadweight displacement ratio 载重系数ballast 压载2、吨位与吨位丈量tonnage 吨位register ton, vessel ton, ton 登记吨gross tonnage 总吨位net tonnage 净吨位register tonnage 登记吨位suez canal tonnage 苏伊士运河吨位panama canal tonnage 巴拿马运河吨位underdeck tonnage 甲板下吨位tween-deck tonnage 甲板间吨位tonnage of hatchways 舱口吨位tonnage measurement 吨位丈量tonnage certificate,certificate of admeasurement 吨位证书tonnage mark 吨位标志register length 登记长度register breadth 登记宽度register depth 登记深度tonnage deck 量吨甲板tonnage length 量吨长度tonnage depth 量吨深度tonnage breadth 量吨宽度exempted space 免除处所deducted space 减除处所propelling power space 推进机械处所enclosure 围蔽处所3、干舷与载重线freeboard 干舷freeboard deck 干舷甲板loadline 载重线loadline mark 载重线标志deadweight scale, displacement scale 载重量表尺4、容积与积载tank capacity 液舱容积cargo capacity 货舱容积grain capacity, grain cargo capacity, grain cubic 散装舱容积bale cargo capacity, bale capacity, bale measure, bale cubic 包装舱容broken stowage, breakage 亏损舱容ullage 膨胀舱容capacity curve 容积曲线capacity plan 舱容图stowage 积载stowage factor 积载因数七、船体结构1、一般hull 船体hull structure, ship structure 船体结构main hull 主船体shell plate 外板strake 列板in and out system 内外搭接式inner strake 内列板outer strake 外列板clinker system 鱼鳞式joggled plating 折曲式flush system 平接式framing 骨架transverse system of framing 横骨架式longitudinal system of framing 纵骨架式combination system of framing 混合骨架式ice strengthening 冰区加强ice belt 冰区带girder, stringer 纵桁longitudinal 纵骨2、船底结构single bottom 单底double bottom 双层底keel 龙骨bar keel 方龙骨plate keel 平板龙骨bottom plate 船底板garboard strake 龙骨翼板bilge strake 舭列板floor, bottom transverse 肋板solid floor 主肋板bracket floor, open floor 框架肋板water tight floor 水密肋板oil tight floor 油密肋板bottom frame 船底肋骨bottom longitudinal 船底纵骨bottom center girder, vertical keel 中底桁duct keel 箱型中底桁bottom side girder 旁底桁half depth girder 半高底纵桁keelson 内龙骨center keelson 中内龙骨side keelson 旁内龙骨inner bottom 内底inner bottom plate 内底板margin plate 内底边板reverse frame 内底横骨inner bottom longitudinal 内底纵骨bilge bracket 舭肘板bilge well 污水井bilge keel 舭龙骨docking keel 坞龙骨3、舷侧结构side plate 舷侧外板sheer strake 舷顶列板rounded sheer strake 圆弧舷顶列板frame 肋股web frame side transverse 强肋骨main frame 主肋骨tweendeck frame 甲板间肋骨intermediate frame 中间肋骨frame spacing 肋骨间距side longitudinal 舷侧纵骨side stringer 舷侧纵桁fender 护舷材5、艏、船艉结构stem 艏柱stern frame, stern post 艉柱rudder post 舵柱propeller post 螺旋桨柱ruder horn 挂舵臂sole piece 艉柱底骨gudgeon 舵钮bow transom plate 首封板stern transom plate 尾封板boss plate 轴包板bossing, shaft bossing, shell bossing 轴包套propeller strut propeller bracket 艉轴架single armed propeller strut 单臂尾轴架A-bracket 人字架deadwood 尾鳍peak frame 尖舱肋骨cant frame 斜肋骨panting arrangement 强胸肋骨panting beam 强胸横梁anchor recess 锚穴hawse pipe 锚链筒chain pipe 锚链管anchor bed 锚床5、甲板、支柱deck 甲板strength deck 强力甲板bulkhead deck 舱壁甲板upper deck 上甲板second deck 第二甲板lower deck 下层甲板bare deck 裸甲板sheathed deck 覆材甲板raised deck 升高甲板raised fore deck 首升高甲板raised quarter deck 尾升高甲板sponson deck 舷伸甲板platform deck 平台甲板deck plate 甲板板stringer plate, deck stringer 甲板边板deck framing 甲板骨架deck beam 横梁cant beam 斜梁strong beam, deck transverse 强横梁hatch side cantilever 舱口悬臂梁hatch end beam 舱口端横梁half beam 半梁beam knee 梁肘板deck girder 甲板纵桁hatch side girder 舱口纵桁deck longitudinal 甲板纵骨stringer angle 舷边角钢hatch 舱口cargo hatch 货舱口oil tank hatch 油舱舱口escape hatch 应急舱口excess hatch 出入舱口hatch coaming 舱口围板companion 舱口围罩tank cleaning opening 洗舱孔scupper 甲板排水孔gutter way 甲板水沟breakwater 挡浪板pillar, stanchion 支柱tubular pillar 管型支柱built up pillar 组合支柱6、舱壁、轴隧、围井bulkhead 舱壁transverse bulkhead 横舱壁longitudinal bulkhead 纵舱壁centerline bulkhead 中纵舱壁slopping bulkhead 斜舱壁collision bulkhead 防撞舱壁after peak bulkhead 尾尖舱舱壁tweendeck bulkhead 甲板间舱壁watertight bulkhead 水密舱壁oil tight bulkhead 油密舱壁plane bulkhead 平面舱壁corrugated bulkhead 槽型舱壁double plate bulkhead 双板舱壁partial bulkhead 局部舱壁partition bulkhead, screen bulkhead 轻舱壁swash bulkhead 制荡舱壁swash plate 制荡板bulkhead plate 舱壁板stiffener 扶强材horizontal girder 水平桁vertical web 竖桁cross tie 边舱撑杆shaft tunnel 轴遂tunnel recess 轴遂端室trunk 围井。
船舶与海洋工程专业专业英语词汇
船舶与海洋工程专业专业英语词汇船舶与海洋工程专业专业英语词汇1、A类a faired set of lines 经过光顺的一组型线 abaft 朝向船尾absence 不存在accommodation 居住(舱室)acquisition cost 购置（获取）成本activate 作动adopt 采用aegis 保护，庇护aerostatic 空气静力学的after perpendicular (a. p. ）艉柱ahead and astern 正车和倒车 air cushion vehicle 气垫船aircraft carrier 航空母舰airfoil 气翼，翼剖面，机面，方向舵airfoil 气翼，机翼alignment chock 组装校准用垫楔(或填料)allowance 公差，余(裕)量，加工裕量，补贴 American Bureau of Shipping (美国)船级社amidships 舯amidships 在舯部amphibious 两栖的angle of attack 攻角angle plate 角钢 anticipated loads encountered at sea在海上遭遇到的预期载荷antiroll fins 减摇鳍 appendage 附体appendage 附件，附体 appendage 附体artisan 技工 assembly line 装配(流水)线athwart ships 朝 (船)横向 at-sea replenishment 海上补给axiomatic 理所当然的，公理化的2、B类back up member 焊接垫板 backing structure 垫衬结构Bar 型材，材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船 base line 基线base, base line 基线basic design 基本设计batten 压条，板条 be in short supply 供应短缺、俏销beam 船身最大宽，横梁beam 船宽，梁bench work 钳工 bevel 折角bid 投标 bidder 投标人(者)bilge 舭，舱底bilge 舭bilge keel 舭龙骨 bilge radius 舭半径bills of material 材料(细目)单 blast 喷丸(除锈)block coefficient 方形系数block coefficient 方形系数Board of Trade (英国)贸易厅 body plan 横剖面图body section 横剖图 Bonjean curve 邦戎曲线boom 吊杆 boundary layer 边界层bow line 前体纵剖线 bow thruster 艏侧推器bow wave 艏波boyant 浮力的bracket 轴支架，支架breadth extreme 最大宽，计算宽breadth moulded 型宽breakbulk 件杂货buckle 屈曲budget 预算，作预算buffer area 缓冲区freeboard deck 干舷甲板 freight rate 运费率fresh water 淡水 frictional resistance 摩擦阻力Froude number 傅汝德数full form 丰满船形full form ship 丰满船型 fullness 丰满度funnel 烟囱galley (船舰，飞机的)厨房Gantt Chart 施工进度表 general arrangement 总布置general arrangement 总布置 Germanischer Lloyd (德国)劳埃德船级社girder 桁，梁gradient 梯度grating 格栅 Green Book (船级社)绿皮书 (登录快速远洋船)ground level building site 平地建造场 group technology 成组建造技术grouting 填缝、灌浆 guided-missile cruiser 导弹巡洋舰habitability 适居性half breadth plan 半宽图handling equipment 装卸设备 hard chine 尖舭headroom 净空高度heave 垂荡 heel 横倾heel 柱脚，踵材，底基，倾斜 hog 中拱hogging 中拱 hold 船舱hole 水流深凹处homogeneous cylinder 均质柱状体hopper barge (自动)倾卸驳 hostile sea 凶险的波浪hostile sea 汹涌波浪 hull block 船体垫块，船体支座 hull form 船形hull form 船形 HVAC (=heating, ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构 hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的icebreaker 破冰船icebreaker 破冰船identified as Essential Changes 标记作“必备变更项” immerse 浸入immerse 浸没impact load 冲击载荷imperial unit 英制单位impression 模槽，型腔，印痕，印象in strake 内列板 in way of…在…处inboard profile 纵剖面图 In-depth analysis 深入研究initial stability at small angle of inclination小倾角初稳性insulation 绝缘，隔离Intact stability 完整稳性Intergovernmental Maritime Consultative Organization 国际海事质询组织Intergovernmental Maritime Consultative Organization (IMCO) 国际政府间海事质询组织International Association of Classification Society (IACS) 国际船级社联合会International Convention for the Safety of Life at Sea (ICSOLAS) 海上生命安全性国际公约International Towing Tank Conference 国际船模试验水池会议intersection 交点，交叉，横断(切)intervening deck 居中甲板introduces a bill 提出一项议案 issue periodically 定期发布(公布) iterative process 选代过程jack 千斤顶 janitorial 勤杂工，房屋照管者joggle 折曲，榫接，弯合 joiner 安装工joiner 细木工(匠)joinery 细木工keel laying 开始船舶建造(原意为“铺设龙骨架”) Kips (= kilo-pounds) 千磅laborer 力工Land borne 陆基的，装在陆地的 landing craft 登陆艇large tank and sphere 大型油罐和球罐launch 发射，下水launching equipment（向水中）投放设备launching way (船舶)下水滑道 LCC(Large Crude Carrier）大型原油轮（载重10~20万吨）lead time 设计至投产、定货至交货的时间 legislation 立法length between perpendicular 两柱间长leveler 调平器，矫平机，矫直机life saving appliance 救生设备 life-cycle cost 生命周期成本lift fan 升力风扇lift offsets 量取型值Light ship weight 空船重量 lighter 港驳船likely 多半，可能line 型线liner 定期航班船liner trade 定期班轮营运业lines plan 型线图liquefied gas carrier 液化气运输船list 倾斜, 表living and utility spaces 居住与公用舱室Lloyd’s Machinery Certificate (LMC) 劳埃德(船舶)机械证书Lloyd’s Register of Shipping (英国)劳埃德船级社Lloyds Rules 劳埃德(船级社)规范LNG containment 液化天然气容器Load Line Regulation 载重线公约、规范load waterline 载重水线load waterplane 载重水线面loft floor 放样台full scale 全尺度loftman 放样工loftman 放样工longitudinal 纵向的longitudinal 纵向的，纵梁longitudinal prismatic coefficient 纵向棱形系数machinery vendor 机械(主机)卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main shafting 主轴系major ship 大型船舶maneuverability 操纵性maritime 海事的，海运的，靠海的，沿海的mark out 划线，划记号marshal 调度mast 桅杆maximum beam amidships 舯最大宽member 部件merchant ship 商船metacenter 稳心metacentric height 稳心高metal plate bath 金属板电镀槽metal worker 金属工metric unit 公制单位midbody （船）中体middle line plane 中线面midship area coefficient 舯横剖面系数midship section 舯横剖面midship section coefficient 舯横剖面系数mill shape 轧钢厂型材module assembly 模块式组装mold loft floor (型线)放样间地板molded lines 型线molder 造型工mould loft 放样间moulded line 型线multihull vessel 多体船Multi-ship program 多种船型建造规划nautical mile 海里naval architect 造船师naval architecture 造船工程naval ship 军船naval architecture 造船学nearuniversal gear 准万向齿轮network flow 网络流程neutral equilibrium 中性平衡normal 法向，法向的，正交的normal force 法向力normal operating condition 常规(正常)运作工况notch 开槽，开凹口Off the shelf 成品的，畅销的，流行的off-center loading 偏移中心的装载offsets 型值offshore drilling 离岸钻井oil-rig 钻油架operational requirement 军事行动需求，运作要求orient 取向，定方位，调整orthogonal 正交的，矩形的out strake 外列板outboard profile 侧视图outfit 舾装outfitter 舾装工outfitting 舾装overall stability 总体稳性overhang 外悬overstocking 存货过剩owner’s staff 船东的雇(职)员paint priming 涂底漆Panama Canal 巴拿马运河panel line system 板材生产线系统parallel middle body 平行中体patternmaker 木模工payload 有效载荷permanent body 永久性组织机构perpendicular（船艏、艉）柱，垂直的，正交的pillar 支柱pin 钉，销pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge (海底) 铺管驳船piping 管路pitch 纵摇plan views 设计图planing hull 滑行船体pleasure ship 游乐用船Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船Polaris (submarine) 北极星级(潜艇)port 左舷portable gate 移动式(可移动)闸门positive righting arm 扶正力臂power and lighting system 动力与照明系统preliminary design 初步设计preliminary/concept design 初步/概念设计pressure vessel 压力容器principal dimensions 主尺度prism 棱柱体prismatic coefficient 棱形系数procurement 采购，获得Program Evaluation and Review Technique 规划评估与复核法quartering sea 尾斜浪, 从船斜后方来的浪quay(横)码头，停泊所racking 倾斜，变形，船体扭转变形radiography X射线照相术，X射线探伤rake 倾角,倾斜ram pressure 速压头，冲压，全压力rectangle 矩形reenlistment 重征服役Registo Italiano Navale (意大利)船级社remedial action 补救措施reserve buoyancy 储备浮力reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力resultant 合力retract 收进revolving crane 旋转式(鹤)吊，转臂吊(车)Reynolds number 雷诺数rigger 索具装配工rigid side walls 刚性侧壁rise of floor 底升risk 保险对象，保险金额rivering warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇rolled angle butt (轧制)角钢焊接头roll-on/roll-off(RO-RO) 滚装rough sea 汹涌的波浪round of beam 梁拱rounded gunwale 修园的舷边rubber tile 橡皮瓦rudder post 舵柱rudder 舵rudder rate 舵率rudder stock 舵杆run 去流段Sag 中垂sagging 中垂scale 缩尺，尺度，尺scale model 缩尺船模scantling 材积sea keeping performance 耐波性能seasickness 晕船seaworthiness 适航性section 剖面，横剖面sections (铁、钢)型材，轧材self-induced 自身诱导的semi finished item 半精加工件semisubmersible drilling rig 半潜式钻井架set course 设定的航线set course 设定航线shaft bossing 轴包套shaft bracket 轴支架shear 剪切，剪力sheer aft 艉舷弧sheer forward 艏舷弧sheer drawing 剖面图sheer plane 纵剖面sheer profile 纵剖线sheer profile 纵剖图sheer(甲板)舷弧sheet metal work 钣金工，冷作工shell plating 船壳板shell 船壳板ship fitter 船舶装配工ship fitter 船体安装工ship fitter 舰船装配工ship form 船型ship Hydrodynamics 水动力学ship owner 船东shipping line 船运航线shipway (造)船台shipwright 船体装配工，造船工人shipyard 船厂shipyard 船厂shipyard schedule chart 船厂施工进度图shoring 支撑，支柱shoulder 船肩sideways 朝侧向six degrees of freedom 六自由度sizable 相当大的skirt（气垫船）围裙slamming 砰击，拍击slice 一部分，薄片sloping shipway 有坡度船台，滑道soft chine 圆舭spare part 备件specially prepared form 专门(特殊)加工的模板spectrum 谱speed-to-length ratio 速长比stability 稳性stable equilibrium 稳定平衡standard 规章starboard 右舷static equilibrium 静平衡statically determinant 静定的statistical 统计学(上)的steel marking 钢板划线steering gear 操纵装置steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 艉stern frame 艉构架，艉框架stern wave 艉波stiffen 加劲，加强stiffener 肋骨strain 应变strake 船体列板stringent safety regulations 严格的安全规章structural alignment 结构校准，组合，组装strut 支柱，支撑构形subassembly (局部)分部装配subdivision 分舱sublet 转包，分包，转租submersible 潜器suction cup 吸盘Suez Canal Tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线super cavitating propeller超空泡螺旋桨superintendent 监督管理人，总段长，车间主任superstructure 上层建筑supertanker 超级油轮supervision of the Society’s surveyor 船级社验船师的监造surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过survivability 生存力SWATCH(Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡switchboard 控制台，开关板tabular freeboard 列成表格的干舷值tacker 定位搭焊工talking paper 讨论文件tangential viscous force 切向粘性力tanker 油轮tanker 油轮tantamount 等值的，相当的taper 弄细，变尖tee T形构件，三通管template 样板tensile stress 拉(张)应力The Register of Shipping of the People’s Republic of China 中国船舶检验局The Titanic 泰克尼克号(巨型邮轮)there is more shape to the shell 船壳板的形状较复杂titanic 巨大的to be craft oriented 与行业有关的，适应于行业性的to run the waterlines 绘制水线toed towards amidships 趾部朝向船舯ton gross=gross ton 长吨=1. 016公吨tonnage 吨位torque 扭矩torsio 扭转的trade 工种, 贸易trailer type transporter 拖车式载运车transfer sideways 横向移动transom (stern) 方尾transverse 横向的transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim 纵倾trim by the stern/bow 艉/艏倾trimaran 三体船trough 波谷tugboat 拖船tumble home(船侧)内倾Type A ship A类船U form U型U. S. Coast Guard 美国海岸警卫队ULCC(Ultra Large Crude Carrier）超级大型原油轮（载重量>40万吨）ultrasonic 超声波的\underwriter (海运)保险商undock 使船出坞upright position 正浮位置V shaped V型的ventilation and air conditioning diagram 通风与空调敷设设计图vertical prismatic coefficient 垂向棱形系数vertical prismatic coefficient 垂向棱形系数vicinity 邻近，附近villain 坏人，罪魁viscosity 粘性VLCC(Very Large Crude Carrier）巨型（原）油轮（载重量>20万吨）V-sectionV型剖面wash 下洗 ,艉流water line 水线waterborne 浮于水上的，水基的waterplane 水线面waterplane area coefficient 水线面积系数watertight integrity 水密完整性wave pattern 波型wavemaking resistance 兴波阻力weather deck 露天甲板weld inspection 焊缝检测welder 焊工weldment 焊件，焊接装配wetted surface 湿面积wing shaft 侧轴yacht 快艇yard issue 船厂开工任务发布书yaw 艏摇yaw 艏摇，摇艏。
船舶工程专业英语词汇
船舶专业英语词汇（按照字母顺序排列）（一）a faired set of line 经过光顺处理的一套型线a pair of stereo photographs 一对立体投影相片abaft 朝向船体abandonment cost 船舶废置成本费用accommodation 居住（舱室）accommodation ladder 舷梯adjust valve 调节阀adjustable-pitch 可调螺距式admiralty 海军部，海事法，制海权，海军上将advance coefficient 进速系数，前进系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli’s law 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索bobstay 首斜尾拉索body plan 横剖面图bolt 螺栓，上螺栓固定Bonjean curve 邦戎曲线boom 吊杆boss 螺旋桨轴榖bottom side girder 旁底桁bottom side tank 底边舱bottom transverse 底列板boundary layer 边界层bow line 前体纵剖线bow wave 艏波bowsprit 艏斜桅bow-thruster 艏侧推器box girder 箱桁bracket floor 框架肋板brake 制动装置brake band 制动带brake crank arm 制动曲柄brake drum 刹车卷筒brake hydraulic cylinder 制动液压缸brake hydraulic pipe 刹车液压管breadth extreme 最大宽，计算宽度breadth moulded 型宽breakbulk 件杂货breasthook 艏肘板bridge 桥楼，驾驶台bridge console stand 驾驶室集中操作台BSRA 英国船舶研究协会buckle 屈曲buffer spring 缓冲弹簧built-up plate section 组合型材bulb plate 球头扁钢bulbous bow 球状船艏，球鼻首bulk carrier 散货船bulk oil carrier 散装油轮bulkhead 舱壁bulwark 舷墙bulwark plate 舷墙板bulwark stay 舷墙支撑buoy tender 航标船buoyant 浮力的buoyant box 浮箱Bureau Veritas 法国船级社butt weld 对缝焊接butterfly screw cap 蝶形螺帽buttock 后体纵剖线by convention 按照惯例，按约定船舶专业英语词汇（按照字母顺序排列）（二）cable ship 布缆船cable winch 钢索绞车CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计算机辅助制造CAM(computer-aided engineering) 计算机辅助工程camber 梁拱cant beam 斜横梁cant frame 斜肋骨cantilever beam 悬臂梁capacity plan 舱容图CAPP(computer –aided process planning) 计算机辅助施工计划制定capsize 倾覆capsizing moment 倾覆力臂captain 船长captured-air-bubble vehicle 束缚气泡减阻船cargo cubic 货舱舱容，载货容积cargo handling 货物装卸carriage 拖车，拖架cast steel stem post 铸钢艏柱catamaran 高速双体船catamaran 双体的cavitation 空泡cavitation number 空泡数cavitation tunnel 空泡水筒center keelson 中内龙骨centerline bulkhead 中纵舱壁centroid 型心，重心，质心，矩心chain cable stopper 制链器chart 海图charterer 租船人chief engineer 轮机长chine 舭，舷，脊chock 导览钳CIM(computer integrated manufacturing) 计算机集成组合制造circulation theory 环流理论classification society 船级社cleat 系缆扣clipper bow 飞剪型船首clutch 离合器coastal cargo 沿海客货轮cofferdam 防撞舱壁combined cast and rolled stem 混合型艏柱commercial ship 营利用船commissary spaces 补给库舱室，粮食库common carrier 通用运输船commuter 交通船compartment 舱室compass 罗经concept design 概念设计connecting tank 连接水柜constant-pitch propeller 定螺距螺旋桨constraint condition 约束条件container 集装箱containerized 集装箱化contract design 合同设计contra-rotating propellers 对转桨controllable-pitch 可控螺距式corrosion 锈蚀，腐蚀couple 力矩，力偶crane 克令吊，起重机crank 曲柄crest (of wave) 波峰crew quarters 船员居住舱criterion 判据，准则Critical Path Method 关键路径法cross-channel automobile ferries 横越海峡车客渡轮cross-sectional area 横剖面面积c row’s nest 桅杆瞭望台cruiser stern 巡洋舰尾crussing range 航程cup and ball joint 球窝关节curvature 曲率curves of form 各船形曲线cushion of air 气垫damage stability 破损稳性damper 缓冲器damping 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at side 甲板边线deck longitudinal 甲板纵骨deck stringer 甲板边板deck transverse 强横梁deckhouse 舱面室，甲板室deep v hull 深v型船体delivery 交船depth 船深derrick 起重机，吊杆design margin 设计余量design spiral 设计螺旋循环方式destroyer 驱逐舰detachable shackle 散合式连接卸扣detail design 详细设计diagonal stiffener 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dimensionless ratio 无量纲比值displacement 排水量displacement type vessel 排水型船distributed load 分布载荷division 站，划分，分隔do work 做功dock 泊靠double hook 山字钩double iteration procedure 双重迭代法double roller chock 双滚轮式导览钳double-acting steam cylinder 双向作用的蒸汽气缸down halyard 降帆索draft 吃水drag 阻力，拖拽力drainage 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilling rig 钻架drillship 钻井船drive shaft 驱动器轴driving gear box 传动齿轮箱driving shaft system 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders 侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings 装以密封垫的开口general arrangement 总布置general cargo ship 杂货船generatrix 母线geometrically similar form 外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress 船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultativ e Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom 内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Soci ety (IACS) 国际船级社联合会International Towing T ank Conference (ITTC) 国际船模试验水池会议intersection 交点，交叉，横断（切）inventory control 存货管理iterative process 迭代过程jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier 液体散货船liquid chemical tanker 液体化学品船list 倾斜living and utility spaces 居住与公用舱室Lloyd’s Register of shipping 劳埃德船级社Lloyd’s Rules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal (transverse) 纵（横）稳心高longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path 金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier 多用途船multi-ship program 多种船型建造规划mushroom ventilator 蘑菇形通风桶mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）N/C 数值控制nautical mile 海里naval architecture 造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩ocean going ship 远洋船off-center loading 偏离中心的装载offsets 型值offshore drilling 离岸钻井offshore structure 离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge 打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft 极地考察船poop 尾楼port 左舷port call 沿途到港停靠positive righting moment 正扶正力矩power and lighting system 动力与照明系统precept 技术规则preliminary design 初步设计pressure coaming 阻力式舱口防水挡板principal dimensions 主尺度Program Evaluation and Review Technique 规划评估与复核法progressive flooding 累进进水project 探照灯propeller shaft bracket 尾轴架propeller type log 螺旋桨推进器测程仪PVC foamed plastic PVC泡沫塑料quadrant 舵柄quality assurance 质量保证quarter 居住区quarter pillar 舱内侧梁柱quartering sea 尾斜浪quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）racking 倾斜，变形，船体扭转变形radiography X射线探伤rake 倾斜raked bow 前倾式船首raster 光栅refrigerated cargo ship 冷藏货物运输船Register （船舶）登录簿，船名录Registo Italiano Navade 意大利船级社regulating knob of fuel pressure 燃油压力调节钮reserve buoyancy 储备浮力residuary resistance 剩余阻力resultant 合力reverse frame 内底横骨Reynolds number 雷诺数right-handed propeller 右旋进桨righting arm 扶正力臂，恢复力臂rigid side walls 刚性侧壁rise of floor 底升riverine warfare vessel 内河舰艇rivet 铆接，铆钉roll 横摇roll-on/roll-off (Ro/Ro) 滚装rotary screw propeller 回转式螺旋推进器rounded gunwale 修圆的舷边rounded sheer strake 圆弧舷板rubber tile 橡皮瓦rudder 舵rudder bearing 舵承rudder blade 舵叶rudder control rod 操舵杆rudder gudgeon 舵钮rudder pintle 舵销rudder post 舵柱rudder spindle 舵轴rudder stock 舵杆rudder trunk 舵杆围井run 去流段sag 中垂salvage lifting vessel 救捞船scale 缩尺，尺度schedule coordination 生产规程协调schedule reviews 施工生产进度审核screen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱sea state 海况seakeeping 适航性seasickness 晕船seaworthness 适航性seaworthness 适航性section moulus 剖面模数sectiongs 剖面，横剖面self-induced 自身诱导的self-propulsion 自航semi-balanced rudder 半平衡舵semi-submersible drilling rig 半潜式钻井架shaft bossing 轴榖shaft bracket 轴支架shear 剪切，剪力shear buckling 剪切性屈曲shear curve 剪力曲线sheer 舷弧sheer aft 艉舷弧sheer drawing 剖面图sheer forward 艏舷弧sheer plane 纵剖面sheer profile 总剖线sheer profile 纵剖图shell plating 船壳板ship fitter 船舶装配工ship hydrodynamics 船舶水动力学shipway 船台shipyard 船厂shrouded screw 有套罩螺旋桨，导管螺旋桨side frame 舷边肋骨side keelson 旁内龙骨side plate 舷侧外板side stringer 甲板边板single-cylinder engine 单缸引擎sinkage 升沉six degrees of freedom 六自由度skin friction 表面摩擦力skirt （气垫船）围裙slamming 砰击sleeve 套管，套筒，套环slewing hydraulic motor 回转液压马达slice 一部分，薄片sloping shipway 有坡度船台sloping top plate of bottom side tank 底边舱斜顶板slopint bottom plate of topside tank 定边舱斜底板soft chine 圆舭sonar 声纳spade rudder 悬挂舵spectacle frame 眼睛型骨架speed-to-length ratio 速长比sponson deck 舷伸甲板springing 颤振stability 稳性stable equilibrium 稳定平衡starboard 右舷static equilibrium 静平衡steamer 汽轮船steering gear 操纵装置，舵机stem 船艏stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒stern counter 尾突体stern ramp 尾滑道，尾跳板stern transom plate 尾封板stern wave 艉波stiffen 加劲，加强stiffener 扶强材，加劲杆straddle 跨立，外包式叶片strain 应变strake 船体列板streamline 流线streamlined casing 流线型套管strength curves 强度曲线strength deck 强力甲板stress concentration 应力集中structural instability 结构不稳定性strut 支柱，支撑构型subassembly 分部装配subdivision 分舱submerged nozzle 浸没式喷口submersible 潜期suction back of a blade 桨叶片抽吸叶背Suez Canal tonnage 苏伊士运河吨位限制summer load water line 夏季载重水线superintendent 监督管理人，总段长，车间主任superstructure 上层建筑Supervision of the Society’s surveyor 船级社验船师的监造书supper cavitating propeller 超空泡螺旋桨surface nozzle 水面式喷口surface piercing 穿透水面的surface preparation and coating 表面加工处理与喷涂surge 纵荡surmount 顶上覆盖，越过swage plate 压筋板swash bulkhead 止荡舱壁SWATH (Small Waterplane Area Twin Hull) 小水线面双体船sway 横荡船舶专业英语词汇（按照字母顺序排列）（七）tail-stabilizer anchor 尾翼式锚talking paper 讨论文件tangential 切向的，正切的tangential viscous force 切向粘性力tanker 油船tee T型构件，三通管tender 交通小艇tensile stress 拉（张）应力thermal effect 热效应throttle valve 节流阀throughput 物料流量thrust 推力thruster 推力器，助推器timber carrier 木材运输船tip of a blade 桨叶叶梢tip vortex 梢涡toed towards amidships 趾部朝向船舯tonnage 吨位torpedo 鱼雷torque 扭矩torque 扭矩trailing edge 随边transom stern 方尾transverse bulkhead plating 横隔舱壁板transverse section 横剖面transverse stability 横稳性trawling 拖网trial 实船试验trim 纵倾trim by the stern/bow 艉艏倾trimaran 三体的tripping bracket 防倾肘板trough 波谷tugboat 拖船tumble home （船侧）内倾tunnel wall effect 水桶壁面效应turnable blade 可转动式桨叶turnable shrouded screw 转动导管螺旋桨tweendeck cargo space 甲板间舱tweendedk frame 甲板间肋骨two nodded frequency 双节点频率ULCC 超级大型原油轮ultrasonic 超声波的underwriter （海运）保险商unsymmetrical 非对称的upright position 正浮位置vapor pocket 气化阱ventilation and air conditioning diagram 通风与空调铺设设计图Venturi section 文丘里试验段vertical prismatic coefficient 横剖面系数vertical-axis(cycloidal)propeller 直叶（摆线）推进器vessel component vender 造船部件销售商viscosity 粘性VLCC 巨型原油轮Voith-Schneider propeller 外摆线直翼式推进器v-section v型剖面wake current 伴流，尾流water jet 喷水（推进）管water plane 水线面watertight integrity 水密完整性wave pattern 波形wave suppressor 消波器，消波板wave-making resistance 兴波阻力weather deck 露天甲板web 腹板web beam 强横梁web frame 腹肋板weler 焊工wetted surface 湿表面积winch 绞车windlass 起锚机wing shaft 侧轴wing-keel 翅龙骨（游艇）working allowance 有效使用修正量worm gear 蜗轮，蜗杆yacht 快艇yard issue 船厂开工任务发布书yards 帆桁yaw 首摇。
干货：船舶工程专业英语词汇,超齐全
干货：船舶工程专业英语词汇,超齐全干货：船舶工程专业英语词汇，超齐全一、各种舱(箱)柜 All kinds of tank1、柴油日用柜 Diesel oil daily tank2、柴油澄清舱 Diesel oil setting tank3、燃油日用柜 Fuel oil daily tank4、燃油澄清舱 Fuel oil setting tank5、滑油澄清舱 Lubricating oil setting tank6、滑油储藏舱 Lubricating oil store tank7、滑油循环舱 Lubricating oil circulating tank8、燃油溢油舱 Fuel oil overflow tank9、燃油油渣舱 Fuel oil sludge tank10、燃油深舱 Fuel oil deep tank11、滑油污油舱 Lubricating dirty oil tank12、滑油溢油舱 Lubricating oil overflow tank13、滑油油渣打舱 Lubricating oil sludge tank14、主机淡水膨胀水箱 M.E fresh water expansion tank15、付机淡水膨胀水箱 A.E fresh water expansion tank16、淡水压力柜 Fresh water pressure tank17、热水压力柜 Hot water pressure tank18、饮水压力柜 Drinking water pressure tank19、淡水舱 Fresh water tank20、饮水舱 Drinking water tank21、锅炉水舱 Boiler water tank22、分油机工作水箱 Purify operating water tank23、汽缸油日用柜 Cylinder oil daily tank24、尾管滑油重力柜 Gravity tank of tube oil25、排气水封箱 Exhaust seal water tank26、蒸馏水水舱 Distilling water tank27、污水井 Bilge well1、滑油系统 Lubricating oil piping system2、燃油系统 Fuel oil piping system3、海水系统 Sea water piping system4、缸套水系统 Cylinder cooling water piping system5、启动空气系统 Start air piping system6、控制空气系统 Control air piping system7、排气系统 Exhaust piping system8、日用供水系统 Daily water piping system9、蒸汽系统 Steam piping system10、锅炉给水和凝水系统 Feed water and condensate of boiler piping system11、燃油净油系统 Fuel oil purified piping system12、燃油输送系统 Fuel oil transport piping system机舱部分 ENGINE ROOM PART二、机舱设备 Machines and equipment in engine room1、主机 Main engine1)主机油底壳 The sump tank of M.E.2)主机飞轮 Fly wheel of M.E3)活塞 Piston2、发电机 Generator engine1)应急发电机 Emergency generator engine2)辅机 Auxiliary3、锅炉 Boiler1)组合锅炉 The composite boiler2)锅炉安全阀 The safety valve of boiler3)燃烧器 Oil burner unit4)水位表 Water level gauge5)水位控制器 Water level controller6)过量蒸气调节阀 Excess steam pressure control valve 4、舵机1)舵机间 Steering room2)舵机装置 Steering-gear3)手操舵装置 Trick wheel plant4)油缸 Oil cylinder5)反馈装置 Feedback device6)舵 Rudder舵叶 Rudder blade舵杆 Rudder stock上舵承 Rudder carrier舵销 Rudder pintle舵杆衬套 rudder stock liner舵杆轴套 Sleeve for rudder stock舵销承衬套 Bush for rudder pintle舵销轴套 Sleeve for rudder pintle上舵承底座 Rudder carrier seat舵销承座 Pintle bearing舵杆承座 Rudder stock bearing挡圈 Retaining ring舵柄 Tiller舵角 The angle of rudder5、空压机 Air compressor1)主空压机 Emergency air compressor2)应急空压机3)主空气瓶 Main air reservoir4)应急空气瓶 Emergency air reservoir5)控制空气瓶 Control air reservoir6、空气干燥器 Air dryer7、分油机 Oil purifier1)燃油分油机 Fuel oil purifier2)柴油分油机 Diesel oil purifier3)滑油分油机 Lubricate oil purifier4)排渣 Sludge discharge8、制淡装置 Fresh water generator9、焚烧炉 Incinerator10、油水分离器 Oil water separator11、生活污水处理器 Sewage treat plant12、大气冷凝器 Atmosphere condenser热水井 Cascade and inspection(hot well)滑油自清滤器 The automatic back-flash lubricating oil filter燃油单元 Fuel oil unit1)主机燃油单元 Fuel oil unit of M.E2)付机燃油单元 Fuel oil unit of A.E3)粘度计 Viscosity controller泵 Pump1)主机滑油泵 Main engine lubricating oil pump2)主机缸套水泵 Main engine cylinder cooling water pump3)主机缸套水预热泵Main engine cylinder cooling water preheating pump4)主机海水泵 Main engine sea water pump5)主机燃油供给泵 Main engine fuel oil supply pump6)主机燃油增压泵 Main engine fuel oil booster pump7)主机十字头泵 Main engine cross head pump8)付机海水泵 Generator engine sea water pump9)付机缸套水泵Generator engine cylinder cooling water pump10)锅炉给水泵 Feed water pump of boiler11)锅炉燃油泵 Fuel oil pump of boiler12)分油机供给泵 Fuel oil supply pump of purifier13)制淡海水泵 Sea water pump of fresh water generator14)压载泵 Ballast pump15)舱底消防泵 Bilge and fire pump17)油渣泵 Sludge oil pump18)柴油输送泵 Diesel oil transport pump19)燃油油输送泵 Fuel oil transport pump20)汽缸油输送泵 Cylinder oil transport pump21)淡水输送泵 Fresh water transport pump22)热水循环泵 Hot water circulating pump23)饮水日用泵 Drinking water pump舱底消防总用泵 Bilge, fire and G.S pump喷淋泵 Sprinkling pump停泊海水泵 Harbor sea water pump Notification of inspection 检查验收通知单Application 申请，申请单Inspection 检验，报验Technical discussion 技术讨论On board 在船上In the workshop 在车间On the slipway 在船台上At pier(wharf) 在码头Fair 尚好的The performance is merely fair 性能尚好Terrible 极坏的，很糟的So so 马马虎虎So far ,so good 到目前，一切顺利Worse更糟的worst最差、最糟Improvement 改进Leave no room for improvement 完美，无缺点Accept 接收Accept subject to 有条件的接收，有待于……做好之后才接收Reject 拒收Comments 意见 defect lish 消除意见清单Item 项目memorandum 备忘录manual n、手册、说明书;a.手控的，手工的drawings 图纸working drawings 施工图finished drawings 完工图approved drawings 认可图drawings for approval 送审认可图supporting technical doucuments 基础技术文件sketch 草图 draw a sketch画草图up to the standard 达到标准substandard 低于标准的crane 吊车building berth 船台slipway 船台、下水滑道dry dock 干无坞pier 突码头、突堤wharf 码头along side (船)靠码头foreman 工长，领班coordinator 调度员inspector 检查员supervisor 管理人、监督人，监造人surveyor 验船师如有进出口业务咨询，欢迎咨询进贸通。
船舶英语词汇
船舶英语词汇船舶英语词汇汇总船舶专业主要培养具备现代船舶与海洋工程设计、研究、建造的基本技能和管理基础知识、计算机编程及应用能力，能在船舶与海洋结构物设计、研究、制造、检验、使用和管理等部门从事技术和管理方面工作的船舶与海洋工程学科高级工程技术人员。
下面店铺为大家推荐一些关于船舶专业的英语词汇，希望对大家的学习有所帮助。
祝纳汽阀图 Zeuner valve diagram零位线 zero line交错铆 zigzag riveting交错铆接 zigzag riveting锌铬黄(漆) zinc chromate锌板 zinc plate保护用]锌板 zinc protector[锌块 zinc slab零值中心安培计 zero center ammeterZ形推进系 Z-peller交错固结 zigzag fastening镀锌 zincing含锌漆 zincrich paint荧光探伤法 zyglo inspection method硅氟化锌 zinc fluosilicate区域?装 zone outfitting零位线 zero line零相电流 zero phase sequence current无推力节距(螺桨) zero thrust pitch锌 zinc锌池 zinc bath零弯矩跨距 zero moment span荧光渗透探伤法 zyglo penetrant method 镀锌 zinc galvanizing (or plating)区域 zone无扭矩节距(螺桨) zero torque pitchZ形材 Z bar曲折接法 zigzag connection交错间断焊接 zigzag intermittent weld 零相[序] zero phase sequence祝纳氏汽阀图 Zeuner valve diagram曲折操纵,Z形操纵 zigzag maneuvering 零升力攻角 zero-lift angle交错焊接 zigzag weld。
船舶专业词典
船舶专业词汇自我补充篇W.B.T 压载水舱MDO 柴油C.O.P 货油泵F.W.G 制淡装置F.O 燃油CRIC. 循环CYL 气缸thruster推力器，助推器H.F.O重油(燃料油)C.F.W pump 循环淡水泵L.O 滑油N.C.O 喷油器HYD. 压力O.D.M SAMPLING PUMP 排油监控取样泵G/B S/B L.O PUMP 齿轮箱滑油备用泵TRANS 输送G/S 总用PURI. 净化器,分油机SERV. 日用Sulphur 硫ER 机舱fire damper 防火档板UV sterilizer紫外线消毒器tally office 理货员办公室Preheater预热器Bow 艏推力装置thrusterevaporator蒸发器booster 增压器FW HYDROPHOR Pp 淡水输送泵fairlead 导缆孔order number 序号cargo 货物execution 实行; 履行; 执行; 完成vibration stress 振动应力ambient 周围的deviation [de•vi•a•tion ] 背离inclination angle倾角dynamic [dy•nam•ic || daɪ'næmɪk] adj. 动力的; 动态的; 动力学的static [stat•ic || 'stætɪk]adj. 静的; 静力的; 静态的; 静止的appliance [ap•pli•ance || ə'plaɪəns]n. 器具, 用具; 应用, 使用; 设备, 装置; 救火车athwartship 横切,横向barometric pressure 大气压Viscosity 粘质, 粘性cSt 是centistokes的缩写，意思是厘斯asphaltenes 沥青质CCAI 碳芳香度指数class notation 船级代号mounting hole 安装孔；固定孔identification plate标志板installation lable 安装标签bracket 支架QMD青岛齐耀瓦锡兰菱重麟山船用柴油机有限公司wiring diagram布线图servo 伺服电动机; 伺服机构Pcs 数量的缩写。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
船舶专业英语词汇（按照字母顺序排列）（一）a faired set of line apair of stereo 片abaft 朝向船体abandonment costaccommodationaccommodationladder 舷梯adjustvalve 调节阀adjustable-pitch 可调螺距式admiralty 海军部，海事法，制海权，海军上将advance coefficient 进速系数，前进系数aerostatic 空气静力学的aft peak bulkhead 艉尖舱壁aft peak tank 艉尖舱aileron 副鳍air cushion vehicle 气垫船anti-rolling tank 减摇水舱appendage 附体artisan 技工assembly line 装配流水线at-sea replenishment 海上补给augment of resistance 阻力增额auxiliary systems 辅机系统auxiliary tank 调节水舱axial advance 轴向进速backing structure 垫衬结构back-up member 焊接垫板balance weight 平衡锤ball bearing 滚珠轴承ball valve 球阀ballast tank 压载水舱bar 型材bar keel 棒龙骨，方龙骨，矩形龙骨barge 驳船baseline 基线basic design 基本设计batten 压条，板条beam 船宽，梁beam bracket 横梁肘板beam knee 横梁肘板bed-plate girder 基座纵桁bending-moment curves 弯矩曲线Benoulli 'law s 伯努利定律berth term 停泊期bevel 折角bidder 投标人bilge 舭，舱底bilge bracket 舭肘板bilge radius 舭半径bilge sounding pipe 舭部边舱水深探管bitt 单柱系缆桩blade root 叶跟blade section 叶元剖面blast 喷丸block coefficient 方形系数blue peter 出航旗boarding deck 登艇甲板boat davit 吊艇架boat fall 吊艇索boat guy 稳艇索经过光顺处理的一套型线photographs 一对立体投影相船舶废置成本费用居住（舱室）air diffuser 空气扩散器air intake 进气口aircraft carrier 航空母舰air-driven water pump 气动水泵airfoil 气翼，翼剖面，机面，方向舵alignment chock 组装校准用垫楔aluminum alloy structure 铝合金结构American Bureau of Shipping 美国船级社amidships 舯amphibious 两栖的anchor arm 锚臂anchor chain 锚链anchor crown 锚冠anchor fluke 锚爪anchor mouth 锚唇anchor recess 锚穴anchor shackle 锚卸扣anchor stock 锚杆angle bar 角钢angle of attack 攻角angle plate 角钢angled deck 斜角甲板anticipated loads encountered at sea 在波浪中遭遇到的预期载荷anti-pitching fins 减纵摇鳍antiroll fins 减摇鳍butt weld 对缝焊接 butterfly screw cap 蝶形螺帽 buttock 后体纵剖线 by convention 按照惯例，按约定 船舶专业英语词汇(按照字母顺序排列) (二)cable ship 布缆船 cable winch 钢索绞车 CAD(computer-aided design) 计算机辅助设计CAE(computer-aided manufacturing) 计 算 机 辅助制造 CAM(computer-aided engineering) 计算机辅助 工程camber 梁拱 cant beam 斜横梁 cant frame斜肋骨cantilever beam 悬臂梁 capacity plan 舱容图 CAPP(ComPUter -aided ProCeSS Pla nning) 计算机辅助施工计划制定CaPSize 倾覆 CaPSizing moment 倾覆力臂CaPtain 船长CaPtUred-air-bUbble vehiCle 束缚气泡减阻船Cargo CUbiC 货舱舱容，载货容积Cargo handling 货物装卸 Carriage 拖车，拖架 CaSt Steel Stem PoSt 铸钢艏柱Catamaran 高速双体船 Catamaran双体的Cavitation 空泡 Cavitation nUmber 空泡数 Cavitation tUnnel空泡水筒Center keelSon 中内龙骨 Centerline bUlkhead中纵舱壁Centroid 型心，重心，质心，矩心 Chain Cable StoPPer 制链器Chart 海图 Charterer 租船人 Chief engineer 轮机长Chine 舭，舷，脊 ChoCk 导览钳CIM(ComPUter integrated manUfaCtUring) 计算机集成组合制造bobstay 首斜尾拉索 body plan 横剖面图bolt 螺栓，上螺栓固定 Bonjean curve 邦戎曲线boom 吊杆 boss 螺旋桨轴榖 bottom side girder旁底桁 bottom side tank 底边舱 bottom transverse底列板boundary layer 边界层 bow line 前体纵剖线 bow wave 艏波 bowsprit 艏斜桅 bow-thruster 艏侧推器 box girder 箱桁 bracket floor 框架肋板brake 制动装置 brake band 制动带 brake crank arm 制动曲柄brake drum刹车卷筒brake hydraulic cylinder 制动液压缸 brake hydraulic pipe 刹车液压管 breadth extreme 最大宽，计算宽度 breadth moulded型宽breakbulk 件杂货 breasthook 艏肘板 bridge 桥楼，驾驶台 bridge console stand 驾驶室集中操作台 BSRA 英国船舶研究协会 buckle 屈曲 buffer spring 缓冲弹簧 built-up plate section组合型材bulb plate 球头扁钢 bulbous bow 球状船艏，球鼻首 bulk carrier 散货船 bulk oil carrier 散装油轮 bulkhead 舱壁 bulwark 舷墙 bulwark plate舷墙板 bulwark stay 舷墙支撑 buoy tender 航标船buoyant 浮力的 buoyant box 浮箱Bureau Veritas法国船级社CirCUlati On theory 环流理论ClaSSifiCati on SOCiety 船级社cleat 系缆扣CIiPPer bow 飞剪型船首CIUtCh 离合器COaStaI Cargo 沿海客货轮COfferdam 防撞舱壁Comb ined CaSt and rolled Stem 混合型艏柱COmmerCiaI ShiP 营利用船COmmiSSary SPaCeS 补给库舱室，粮食库Com mon Carrier 通用运输船COmmUter 交通船COmPartme nt 舱室COmPaSS 罗经con CePt deSig n 概念设计conn eCt ing tank 连接水柜COnStraintCOn diti on 约束条件COntainer 集装箱COntain erized 集装箱化con tract desig n 合同设计con tra-rotati ng propellers 对转桨con trollable-pitch 可控螺距式corrosio n 锈蚀，腐蚀couple 力矩，力偶Crane 克令吊，起重机Cra nk 曲柄CreSt (of WaVe) 波峰CreW quarters 船员居住舱CriteriO n 判据，准则CritiCaI Path MethOd 关键路径法CrOSS-Cha nnel automobile ferries 横越海峡车客渡轮CrOSS-SeCti onal area 横剖面面积crow ' SneSt 桅杆瞭望台CrUiSer Ster n 巡洋舰尾CrUSS ing range 航程CUP and ball joint 球窝关节CUrVatUre 曲率CUrVeS of form 各船形曲线CUShi on of air 气垫damage StabiIity 破损稳性damper 缓冲器damp ing 阻尼davit arm 吊臂deadweight 总载重量de-ballast 卸除压载deck line at Side 甲板边线deck Ion gitudi nal 甲板纵骨deck Str in ger 甲板边板deck tran SVerSe 强横梁deckhouse 舱面室，甲板室deep V hull 深V型船体delivery 交船depth 船深derrick 起重机，吊杆desig n margin 设计余量design SPiraI 设计螺旋循环方式destroyer 驱逐舰detachable ShaCkIe 散合式连接卸扣detail desig n 详纟田设计diago nal Stiffe ner 斜置加强筋diagram 图，原理图，设计图diesel engine 柴油机dime nsionl ess ratio 无量纲比值displaceme nt 排水量displaceme nt type VeSSeI 排水型船distributed load 分布载荷divisio n 站，戈U分，分隔do work 做功dock 泊靠double hook 山字钩double iterati on PrOCedUre 双重迭代法double roller chock 双滚轮式导览钳double-acting Steam cylinder 双向作用的蒸汽气缸dow n halyard 降帆索draft 吃水drag 阻力，拖拽力drain age 排水draught 吃水，草图，设计图，牵引力dredge 挖泥船drift 漂移，偏航drilli ng rig 钻架drillship 钻井船drive Shaft 驱动器轴driv ing gear box 传动齿轮箱driv ing Shaft SyStem 传动轴系dry dock 干船坞ducted propeller 导管螺旋桨dynamic supported craft 动力支撑型船舶dynamometer 测力计，功率计船舶专业英语词汇（按照字母顺序排列）（三）e.h.p 有效马力eccentric wheel 偏心轮echo-sounder 回声探深仪eddy 漩涡eddy-making resistance 漩涡阻力efficiency 供给能力，供给量electrohydraulic 电动液压的electroplater 电镀工elevations 高度，高程，船型线图的侧面图，立视图，纵剖线图，海拔empirical formula 经验公式enclosed fabrication shop 封闭式装配车间enclosed lifeboat 封闭式救生艇end open link 末端链环end shackle 末端卸扣endurance 续航力endurance 续航力，全功率工作时间engine room frame 机舱肋骨engine room hatch end beam 机舱口端梁ensign staff 船尾旗杆entrance 进流段erection 装配，安装exhaust valve 排气阀expanded bracket 延伸肘板expansion joint 伸缩接头extrapolate 外插fair 光顺faised floor 升高肋板fan 鼓风机fatigue 疲劳feasibility study 可行性研究feathering blade 顺流变距桨叶fender 护舷ferry 渡轮，渡运航线fillet weld connection 贴角焊连接fin angle feedback set 鳍角反馈装置fine fast ship 纤细高速船fine form 瘦长船型finite element 有限元fire tube boiler 水火管锅炉fixed-pitch 固定螺距式flange 突边，法兰盘flanking rudders侧翼舵flap-type rudder 襟翼舵flare 外飘，外张flat of keel 平板龙骨fleets of vessels 船队flexural 挠曲的floating crane 起重船floodable length curve 可进长度曲线flow of materials 物流flow pattern 流型，流线谱flush deck vessel 平甲板型船flying bridge 游艇驾驶台flying jib 艏三角帆folding batch cover 折叠式舱口盖folding retractable fin stabilizer 折叠收放式减摇鳍following edge 随边following ship 后续船foot brake 脚踏刹车fore peak 艏尖舱forged steel stem 锻钢艏柱forging 锻件，锻造forward draft mark 船首水尺forward/afer perpendicular 艏艉柱forward/after shoulder 前/ 后肩foundry casting 翻砂铸造frame 船肋骨，框架，桁架freeboard 干舷freeboard deck 干舷甲板freight rate 运费率fresh water loadline 淡水载重线frictional resistance 摩擦阻力Froude number 傅汝德数fuel/water supply vessel 油水供给船full form 丰满船型full scale 全尺度fullness 丰满度funnel 烟囱furnishings 内装修gaff 纵帆斜桁gaff foresail 前桅主帆gangway 舷梯gantt chart 甘特图gasketed openings general arrangement general cargo ship generatrix 母线geometrically similarform外形相似船型girder 桁梁，桁架girder of foundation 基座纵桁governmental authorities 政府当局，管理机构gradient 梯度graving dock 槽式船坞Green Book 绿皮书，19 世纪英国另一船级社的船名录，现合并与劳埃德船级社，用于登录快速远洋船gross ton 长吨（1.016 公吨）group technology 成祖建造技术GT 成组建造技术guided-missile cruiser 导弹巡洋舰gunwale 船舷上缘gunwale angle 舷边角钢gunwale rounded thick strake 舷边圆弧厚板guyline 定位索gypsy 链轮gyro-pilot steering indicator 自动操舵操纵台gyroscope 回转仪船舶专业英语词汇（按照字母顺序排列）（四）half breadth plan 半宽图half depth girder 半深纵骨half rounded flat plate 半圆扁钢hard chine 尖舭hatch beam sockets 舱口梁座hatch coaming 舱口围板hatch cover 舱口盖hatch cover 舱口盖板hatch cover rack 舱口盖板隔架hatch side cantilever 舱口悬臂梁hawse pipe 锚链桶hawsehole 锚链孔heave 垂荡heel 横倾heel piece 艉柱根helicoidal 螺旋面的，螺旋状的hinge 铰链hinged stern door 艉部吊门HMS 英国皇家海军舰艇hog 中拱hold 船舱homogeneous cylinder 均质柱状体hopper barge 倾卸驳horizontal stiffener 水平扶强材hub 桨毂，轴毂，套筒hull form 船型，船体外形hull girder stress船体桁应力HVAC(heating ventilating and cooling) 取暖，通风与冷却hydraulic mechanism 液压机构hydrodynamic 水动力学的hydrofoil 水翼hydrostatic 水静力的IAGG(interactive computer graphics) 交互式计算机图像技术icebreaker 破冰船icebreaker 破冰船IMCO(Intergovernmental Maritime Consultativ e Organization) 国际海事质询组织immerse 浸水，浸没impact load 冲击载荷imperial unit 英制单位in strake 内列板inboard profile 纵剖面图incremental plasticity 增量塑性independent tank 独立舱柜initial stability at small angle of inclination 小倾角初稳性inland waterways vessel 内河船inner bottom内底in-plane load 面内载荷intact stability 完整稳性intercostals 肋间的，加强的International Association of Classification Soci ety (IACS) 国际船级社联合会International Towing T ank Conference (ITTC)国际船模试验水池会议intersection 交点，交叉，横断(切) inventory control 存货管理iterative process 迭代过程装以密封垫的开口总布置杂货船jack 船首旗jack 千斤顶joinery 细木工keel 龙骨keel laying 开始船舶建造kenter shackle 双半式连接链环Kristen-Boeing propeller 正摆线推进器landing craft 登陆艇launch 发射，下水launch 汽艇launching equipmeng （向水中）投放设备LCC 大型原油轮leading edge 导缘，导边ledge 副梁材length overall 总长leveler 调平器，矫平机life saving appliance 救生设备lifebuoy 救生圈lifejacket 救生衣lift fan 升力风扇lift offsets 量取型值light load draft 空载吃水lightening hole 减轻孔light-ship 空船limbers board 舭部污水道顶板liner trade 定期班轮营运业lines 型线lines plan 型线图Linnean hierarchical taxonomy 林式等级式分类学liquefied gas carrier 液化气运输船liquefied natural gas carrier 液化天然气船liquefied petroleum gas carrier 液化石油气船liquid bulk cargo carrier liquid chemical tanker list 倾斜living and utility spacesLloyd 'R s egister of shipping 劳埃德船级社Lloyd 'R s ules 劳埃德规范Load Line Convention 载重线公约load line regulations 载重线公约，规范load waterplane 载重水线面loft floor 放样台longitudinal bending 纵总弯曲longitudinal prismatic coefficient 纵向菱形系数longitudinal strength 纵总强度longitudinally framed system 纵骨架式结构luffing winch 变幅绞车machinery vendor 机械（主机）卖方magnet gantry 磁力式龙门吊maiden voyage 处女航main impeller 主推叶轮main shafting 主轴系major ship 大型船舶maneuverability 操纵性manhole 人孔margin plate 边板maritime 海事的，海运的，靠海的mark disk of speed adjusting 速度调整标度盘mast 桅杆mast clutch 桅座matrix 矩阵merchant ship 商船Merchant Shipbuilding Return 商船建造统计表metacenter 稳心metacentric height 稳心高metal plate path金属板电镀槽metal worker 金属工metric unit 公制单位middle line plane 中线面midship section 舯横剖面midship section coefficient 中横剖面系数ML 物资清单，物料表model tank 船模试验水池monitoring desk of main engine operation 主机操作监视台monitoring screen of screw working condition 螺旋桨运转监视屏more shape to the shell 船壳板的形状复杂mould loft 放样间multihull vessel 多体船multi-purpose carrier multi-ship program mushroom ventilator mutually exclusive attribute 相互排它性的属性船舶专业英语词汇（按照字母顺序排列）（五）longitudinal （transverse）液体散货船液体化学品船居住与公用舱室多用途船多种船型建造规划蘑菇形通风桶纵（横）稳心高N/C 数值控制nautical mile 海里naval architecture造船学navigation area 航区navigation deck 航海甲板near-universal gear 准万向舵机，准万向齿轮net-load curve 静载荷曲线neutral axis 中性轴，中和轴neutral equilibrium 中性平衡non-retractable fin stabilizer 不可收放式减摇鳍normal 法向的，正交的normal operating condition 常规运作状况nose cone 螺旋桨整流帽notch 开槽，开凹口oar 橹，桨oblique bitts 斜式双柱系缆桩远洋船偏离中心的装载离岸钻井离岸工程结构物oil filler 加油点oil skimmer 浮油回收船oil-rig 钻油架on-deck girder 甲板上桁架open water 敞水optimality criterion 最优性准则ore carrier 矿砂船orthogonal 矩形的orthogonal 正交的out strake 外列板outboard motor 舷外机outboard profile 侧视图outer jib 外首帆outfit 舾装outfitter 舾装工outrigger 舷外吊杆叉头overall stability 总体稳性overhang 外悬paddle 桨paddle-wheel-propelled 明轮推进的Panama Canal 巴拿马运河panting arrangement 强胸结构，抗拍击结构panting beam 强胸横梁panting stringer 抗拍击纵材parallel middle body 平行中体partial bulkhead 局部舱壁payload 有效载荷perpendicular 柱，垂直的，正交的photogrammetry 投影照相测量法pile driving barge打桩船pillar 支柱pin jig 限位胎架pintle 销，枢轴pipe fitter 管装工pipe laying barge 铺管驳船piston 活塞pitch 螺距pitch 纵摇plan views 设计图planning hull 滑行船体Plimsoll line 普林索尔载重线polar-exploration craft poop 尾楼port 左舷port call 沿途到港停靠positive righting moment power and lighting system precept 技术规则preliminary design pressure coaming principal dimensionsProgram Evaluation and Review Technique 划评估与复核法progressive flooding project 探照灯propeller shaft bracket propeller type log PVC foamed plastic quadrant 舵柄quality assurance quarter 居住区quarter pillar quartering sea quasi-steady wave 准定长波quay 码头，停泊所quotation 报价单船舶专业英语词汇（按照字母顺序排列）（六）ocean going shipoff-center loadingoffsets 型值offshore drillingoffshore structure极地考察船正扶正力矩动力与照明系统初步设计阻力式舱口防水挡板主尺度累进进水尾轴架螺旋桨推进器测程仪PVC 泡沫塑料质量保证舱内侧梁柱尾斜浪racking 倾斜，变形，船体扭转变形 radiography X 射线探伤 rake 倾斜 raked bow前倾式船首raster 光栅 refrigerated cargo ship 冷藏货物运输船 Register （船舶）登录簿，船名录 Registo Italiano Navade意大利船级社regulating knob of fuel pressure 燃油压力调节 钮内底横骨 雷诺数右旋进桨 扶正力臂，恢复力臂 刚性侧壁 riverine warfare vessel rivet 铆接，铆钉 roll 横摇 roll-on/roll-off (Ro/Ro) rotary screw propeller rounded gunwale rounded sheer strake rubber tile 橡皮瓦 rudder 舵 rudder bearing rudder blade rudder control rod rudder gudgeon rudder pintle rudder post rudder spindle rudder stock rudder trunk run去流段 sag 中垂 salvage lifting vessel scale 缩尺，尺度 schedule coordination schedule reviewsscreen bulkhead 轻型舱壁Sea keeping performance 耐波性能sea spectra 海浪谱 sea state 海况 seakeeping 适航性 seasickness 晕船 seaworthness 适航性 seaworthness 适航性 section moulus 剖面模数 sectiongs 剖面，横剖面 self-induced 自身诱导的 self-propulsion 自航 semi-balanced rudder 半平衡舵 semi-submersible drilling rig半潜式钻井架shaft bossing 轴榖 shaft bracket 轴支架 shear 剪切，剪力 shear buckling 剪切性屈曲 shear curve剪力曲线sheer 舷弧 sheer aft 艉舷弧sheer drawing 剖面图 sheer forward 艏舷弧 sheer plane 纵剖面 sheer profile 总剖线 sheer profile 纵剖图 shell plating船壳板ship fitter 船舶装配工 ship hydrodynamics 船舶水动力学 shipway 船台 shipyard 船厂 shrouded screw 有套罩螺旋桨，导管螺旋桨 side frame 舷边肋骨 side keelson 旁内龙骨 side plate 舷侧外板 side stringer 甲板边板single-cylinder engine 单缸引擎 sinkage 升沉 six degrees of freedom 六自由度skin friction表面摩擦力skirt (气垫船)围裙 slamming 砰击 sleeve 套管，套筒，套环 slewing hydraulic motor 回转液压马达储备浮力 剩余阻力reserve buoyancy residuary resistance resultant 合力 reverse frame Reynolds number right-handed propellerrighting arm rigid side walls rise of floor 底升内河舰艇滚装回转式螺旋推进器 修圆的舷边圆弧舷板救捞船生产规程协调 施工生产进度审核舵承 舵叶操舵杆 舵钮舵销 舵柱舵轴 舵杆 舵杆围井slice 一部分，薄片 sloping shipway有坡度船台sloping top plate of bottom side tank 斜顶板slopint bottom plate of topside tank 底板Suez Canal tonnage底 边 舱 superintendent superstructure 定边舱 斜Supervision ofthe验船师的监造书苏伊士运河吨位限制 监督管理人，总段长，车间主任 上层建筑Society 's s urveyor 船 级社supper cavitating propeller 超空泡螺旋桨 surface nozzle 水面式喷口 surface piercing 穿透水面的 surface preparation and coating 表面加工处理 与喷涂surge 纵荡 surmount 顶上覆盖，越过 swage plate 压筋板 swash bulkhead止荡舱壁SWATH (Small Waterplane Area Twin Hull)小水线面双体船steering gear 操纵装置，舵机 stem 船艏 stem contour 艏柱型线stern 船艉stern barrel 尾拖网滚筒 stern counter 尾突体 stern ramp 尾滑道，尾跳板 stern transom plate 尾封板 stern wave 艉波 stiffen 加劲，加强 stiffener 扶强材，加劲杆 straddle 跨立，外包式叶片 strain 应变 strake 船体列板 streamline 流线 streamlined casing 流线型套管 strength curves 强度曲线 strength deck强力甲板stress concentration 应力集中 structural instability结构不稳定性strut 支柱，支撑构型 subassembly 分部装配 subdivision 分舱 submerged nozzle 浸没式喷口 submersible 潜期 tail-stabilizer anchor 尾翼式锚talking paper讨论文件tangential 切向的，正切的 tangential viscous force 切向粘性力 tanker 油船 tee T 型构件，三通管 tender 交通小艇 tensile stress 拉(张)应力thermal effect 热效应 throttle valve 节流阀 throughput 物料流量 thrust 推力 thruster 推力器，助推器 timber carrier 木材运输船 tip of a blade 桨叶叶梢tip vortex梢涡toed towards amidships 趾部朝向船舯 tonnage 吨位 torpedo 鱼雷 torque 扭矩 torque 扭矩 trailing edge 随边 transom stern 方尾suction back of a blade桨叶片抽吸叶背transverse bulkhead plating 横隔舱壁板summer load water line夏季载重水线soft chine 圆舭 sonar 声纳 spade rudder 悬挂舵 spectacle frame 眼睛型骨架 speed-to-length ratio 速长比 sponson deck 舷伸甲板 springing 颤振 stability 稳性 stable equilibrium稳定平衡starboard 右舷 static equilibrium 静平衡steamer 汽轮船sway 横荡船舶专业英语词汇（按照字母顺序排列） （七）transverse section 横剖面 web frame 腹肋板 transverse stability横稳性weler 焊工trawling 拖网wetted surface 湿表面积 trial 实船试验winch 绞车trim 纵倾windlass 起锚机 trim by the stern/bow 艉艏倾wing shaft 侧轴trimaran 三体的wing-keel 翅龙骨（游艇）tripping bracket 防倾肘板working allowance 有效使用修正量 trough 波谷 worm gear 蜗轮，蜗杆 tugboat 拖船yacht 快艇tumble home ( 船侧）内倾yard issue 船厂开工任务发布书 tunnel wall effect 水桶壁面效应 yards 帆桁 turnable blade可转动式桨叶yaw 首摇turnable shrouded screw 转动导管螺旋桨 tweendeck cargo space 甲板间舱 tweendedk frame 甲板间肋骨 two nodded frequency 双节点频率ULCC 超级大型原油轮 ultrasonic 超声波的 ventilation and air conditioning diagram 与空调铺设设计图Venturi section 文丘里试验段 vertical prismatic coefficient vertical-axis(cycloidal)propeller 进器横剖面系数 直叶 （摆线） 推vessel component vender 造船部件销售商viscosity 粘性 VLCC 巨型原油轮 Voith-Schneider propeller外摆线直翼式推进器 v-section v 型剖面 wake current 伴流，尾流 water jet 喷水(推进)管 water plane 水线面 watertight integrity 水密完整性 wave pattern 波形 wave suppressor 消波器，消波板 wave-making resistance 兴波阻力weather deck 露天甲板 web 腹板 web beam 强横梁underwriter unsymmetrical upright position vapor pocket海运）保险商 非对称的 正浮位置 气化阱通风。