PC900V 光藕

reliability and
sensor
(aircraft, train, automobile . Rescue and security
(3)
Please do not use this product for equipment which and safety in function and precision, such as : * Space [ * Nuclear equipment power control * Telpment . Medical
electrical
non-coherent
light emitting
7. Notes Refer to the attached sheet-l-l, 2.
SHARP CORPORATION PCSOOV
Voltage
regulator I
cc
PCSOOV SHARP
Anode
3
Cathode
*l The derating factors of absolute maximum ratings due to ambient temperature areshowninFig. 1, 2, 3. *2 Pulse widths 100 /1s, Dutyratio : 0.001
of
SHARP CORPORATION
SA-88049D
MODEL No.
1 March25,
1996
PAGE
PCSOOV
l/9
i
1. Application This specification applies to the outline and characteristics Model No. PCSOOV. of photocopier
for use outlined no responsibility maximum ratings below.
product
is designed
for use visual equipment . Computers
ln the following equipment (Terminal)
application * Home * Measuring
1
Appropriate measures, such as tbil-safe design and the safety design of the overall system and equipment, and safety when this product is used for equipment safety in function and precision, such as ; * Transportation * Traffic signals [ * Other safety control * Gas equipment and leakage safety equipment breakers
areas appliances
:
* OA equipment * Telecommunication * Tooling machines
* Audio
equipment
[
If the use of the product (2) or (3). please be sure (2)
in the above application to observe the precautions
are any
3. Please
contact
questions
CUSTOMER’S
APPROVAL
DATE PRESENTED
BY T. Matsumura. Department Engineering Opto-Electronic
DATE
BY
ELECOM
SHARP
General Manager Dept.,11 Devices Div. Group CORPORATION
oil.)
6.2 Business dealing name (” 0” mark indicates business dealing name of ordered product) Product G Business dealing name PCSOOV PC9OOVY Applied to products as a option (Attached sheets -2-l to 2-4.) Remarks
Name
Drawing No.
SHARP CORPORATION
SA-88049D
MODEL No.
1 March25.
1996
PAGE
PCSOOV
3. Ratings and characteristics 3.1 Absolute maximum ratings Ta=25C Parameter unit mA A V P~~ Supply voltage High level output voltage output Low level output current *l Power dissipation I r, PO Ptot viso Topr Tstg I Tsol I I 50 150 170 5.0 -25 to +85 -40 to 125 260 I I m.A mW mW kVrms ‘C “C ‘C vcc
2.
When using this product, please observe the absolute maximum ratings and the instructions in these specification sheets. as well as the precautions mentioned below. Sharp assumes for any damage resulting from use of the product which does not comply with the absolute and the instructions included in these specification sheets, and the precautions mentioned (Precautions) (1) This
SHARP CORPORATION
6.3 This Model is approved Approved Model
by UL.
No. : PCSOOV
UL file No. : E64380
6.4 Theory
of operation current (I,)
(1) When the forward current of above the “H-L” threshold input is applied to the input side, the output will go “Low level”. (21 When input the forward current on the input side goes below current (I,1 the output will go “High level”.
REPRESENTATIVE OPTO-ELECTRONIC
SPECIFICATION
f
DEVICE SPECIFICATION FOR
Business dealing
PHOTOCOUPLER
MODEL No.
name
I
PCSOOV I
1. These Please specification sheets include do not reproduce or cause materials protected anyone to reproduce under them copyright without of Sharp Corporation Sharp’s consent. (“Sharp”).
PREPARED
BY:
DATE:
SPEC. No.
SA-88049D March 25, 1996
SHARP
APPROVED
7 35h
ISSUE
PAGE
15 Pages DMSION DEVICES DIV.
BY: niMj.;?
DATE: Tf6
/ .J-
ELECTRONIC COMPONE,NTS GROUP SHARP CORPORATION
5. Incoming inspection Refer to the attached sheet, page 9.
6. Supplement 6.1 Isolation voltage shall be measured in the following method. ( 1) Short among pins 1 to 3 on the primary side and among pins 4 to 6 on the secondary side. (2) The dielectric whhstand tester with zero-cross circuit shall be used. (3) The wave form of applied voltage shall be a sine wave. (It is recommended that the isolation voltage be measured in insulation
the “L-H”
threshold
6.5 This product This product This product
is not designed is assembled incorporates