英文图纸技术翻译

340121-05-H

NOTES ：（UNLESS OTHERWISE SPECIFIED）:

备注：（除非另有说明）

1. MATERIAL ：RTP 900-P1700 ZC-700458 BLUE (UDEL POLYSULFONE ，COLOR BLUE).

材料：RTP 900-P1700 RTP 900-P1700 蓝色（聚砜，蓝色）

NO USED OR RECYCLED MATERIAL PERMITTED .

不允许使用用过的或者回收的材料

PROVIDED RAW MATERIAL LOT CERTIFICATION WITH EACH SHIPMENT WHICH INCLUDES SUPPLIER NAME LOT NUMBER ，AND MATERIAL TYPE OR SPECIFICATION NUMBER .

提供每一次交付来料原材料批号认证，包括供应商名称批号，材料类型或者规格编号

2. ALL EJECTOR PIN AND GATING VESTIGE TO BE FLUSH OR RECESSED WITHIN .005 OF SURFACE.

所有的顶针和水口残留要与部品表面齐平，深入表面最大不能超过0.005

INTUITIVE SURGICAL ENGINEER TO APPROVE ALL GATE AND EJECTOR PIN LOCATIONS .

要与客户确认水口和顶针位置

3. NO CRACKS ，FLASH，SINKS，OR KNIT LINES PERMITTED UNLESS APPROVED BY INTUITIVE SURGICAL . 不能有裂纹，披峰，缩水，熔接线，除非客户同意

VISUALLY INSPECT FOR COMPLETE FILL AND IRREGULARITIES

肉眼检查一下打满胶的部品和其他不良

4. ALL MOLD RELEASE MUST BE APPROVED BY INTUITIVE SURGICAL ENGINEERING PRIOR TO

USE .脱模剂要经过外观工程科同意后使用

5. DIAMETRICAL TAPER TO CONFORM TO ISO 594/1-1986 （LUER FITTING ）.

直径的锥形符合ISO 594/1 - 1986(鲁尔接口配件)

USE GO/NOGO GAGE DEFINED IN ISO 594/1-1986 ，FIGURE 3C （ISI PN 710014）TO INSPECT CAVITY .通止规使用参考ISO 594/1-1986，检查前模用FIGURE 3C （ISI PN 710014）

6. NOT FULLY DIMENSIONED OBTAIN MISSING INFORMATION FROM CAD FILES .

没标注的尺寸参见CAD图纸

7. PARTS TO BE CLEAN , WITH NO CONTAMINATION OR LUBRICANT .

部品要干净,没有污染物质或润滑剂

NO VISIBLE PARTICULATE WHEN EXAMINED WITHOUT MAGNIFICATION .

用肉眼检查，不要有可见微粒

8. PACKAGE IN CLEAN CLEAR PLASTIC BAGS .

包装使用干净的透明塑料袋

LABEL PACKAGING WITH INTUITIVE ’S PART NUMBER , REVISION (EG .340121-01-H),PURCHASE ORDER NUMBER，AND QUANTITY.

包装标签上要有：直观的零件号,修订版本(如.340121-01-H)，采购订单号和数量。

9. PROVIDE DATA FOR ALL SQC POINTS ON FORM 800189 OR EQUIVALENT WITH EVERY DELIVERY .

每一次交付，提供数据给所SQC注意点以800189形式（表格）或类似的形式。

USE C=0 SAMPLING PLAN PER DOP 854062，“INCOMING INSPECTION”.

每一DOP 854062使用c=0抽样计划，来料检查

3401209-02-B

NOTES ：（UNLESS OTHERWISE SPECIFIED）:

备注：（除非另有说明）

1.MATERIAL ：CLEAR POLYCABONATE, CALSS VI, DOW PC 2081-15

材料：PC , 等级VI , DOW(陶氏化学) PC 2081-15

2. SURFACE FINISH SPI#2 OR BETTER WITH NO GATE OR PARTING LINE

表面SPI#2处理，或者最好有没水口、分型线

3. FINISH ：SPI#4 OR BETTER UNLESS OTHERWISE SPECIFIED

抛光：SPI#4 或者更好除非另有说明

4. 100% VIRGIN MATERIAL ONLY ，NO USED OR RECYCLED MATERIAL PERMITTED .

100% 纯原料，不允许使用用过的或者回收的材料

5. ISI ENGINEERING TO APPROVE ALL GATE AND EJECTOR PIN LOCATIONS

所有水口和顶针位置要经过ISI 同意确认

6. ALL EJECTOR PIN AND GATING VESTIGE FLUSH TO WITHIN .010 OF SURFACE.

所有的顶针和水口残留不得高出部品表面0.10

7. Sharp Corners maybe r .005 max

锐角最大半径为0.005

8. DRAFT ANGLE IS 1ºAS REQUIRED UNLESS OTHERWISE SPECIFIED

按照要求，拔模角度为 1º，除非另有说明

9. MATING RADⅡTO BLEND SMOOTHLY . NO MISMATCH PERMISSIBLE.

不允许有段差

10. FLASH NOT TO EXCEED .005 “X.010”AND NO LOOSE FLASH PERMITTED

披峰不能超过0.005，不允许有松散的披峰

11. VISUALLY INSPECT FOR COMPLETE FILL AND IRREGULARITIES

肉眼检查一下是否打满胶和其他不良

12. NO CRACKS OR KNIT LINES PERMITTED

不能有裂纹，熔接线

13. UNDER NORMAL LIGHTING ，REVIEWED FOR 3 TO 5 SECONDS，WITHOUT MAGNIFICATION AT A DISTANT OF 16 TO 18 INCHES THERE SHALL BE NO PARTICULARS OR FIBER LARGER THAN 0.25MM^2 AS MEASURED ON A TAPPI CHART .参照TAPPI图表来衡量，在正常照明，16 - 18英寸的距离，没有放大情况下，查看3到5秒钟,没有微粒或纤维大于0.25毫米^ 2

PACKAGE SHALL BE BAGGED ,USING BAGS THAT ARE CLEAN ,FREE OF OIL AND DEBRIS WHENNSPECT IN THE SAME MANNER . 包装应该用袋装，袋子应该干净，没有油污和残屑

HEAT SEAL BOTH BAGS .LABEL EACH BAG WITH INTUITIVE’S NUMBER REVISION LEVEL，QUANTITY ,SUPPLIER LOT NUMBER AND PURCHASE ORDER NUMBER.

热封包装（两头？？），包装袋标签上要有：直观的修订版本，数量，供应商批次号，采购订单号14.PROVIDED RAW MATERIAL LOT CERTIFICATION INSPECTION RESULTS WITH EACH SHIPMENT ，INCLUDE SUPPLIER NAME ，LOT NUMBER AND MATERIAL TYPE OR SPECIFICATION No.

每一次交付，提供原材料的证明检测结果，包括：批次号，材料类型或者规格编号