友达全视角7寸工业液晶屏-G070VVN01.2 工控屏
友达5.7寸液晶屏G057VTN01 V0规格书-杭州旭虹科技有限公司
G057VTN01 V0 Color TFT-LCD Module5.7” VGA Landscape LED BacklightWide Temperature Range Mercury-free solution RoHS and Halogen-freeComplianceHigh Shock/Vibration Resistance Outline and Interface are fullycompatible with G057VN01 serials(Preliminary)Size (inch)5.7” ModelG057VN01 V210 Resolution (pixel) 640(RGB) x 480 Active Area (mm) 115.2(H) x 86.4(V)Pixel Pitch (mm) 0.18 x 0.18Mode TNLCD Surface Anti-Glare, Hardness 3HNumber of Colors 262K View Angle (L/R/U/D) 80/80/70/70 (typ.) Brightness(nit) (25℃) 500(min.), 600 (typ.)Contrast Ratio (25℃) 800:1 (typ.) Response Time (ms) 25 (typ.) LED Life (hrs.)50K Power Consumption (W) 3.74W Supply Voltage (V) 3.3V Storage Temp. (℃) -30 ~ 85 Operation Temp. (℃) -30 ~ 85Outline Dimension (mm) 144.0(H) x 104.6(V) x12.3(D) (typ.) Weight (g) 150g (typ.), 165g (max.)InterfaceCMOSTFT- LCD Interface Signal Description:Note 1: “Low” stands for 0V. “High” stands for 3.3V. “NC” stands for ”No Connection”.TFT- LCD Signal (CN1): LCD Connector: ManufacturerStarconnConnector Model Number 089H33-000100-G2-R, compatible withIMSA-9637S-33Y902 & ELCO 08-6210--033-340-800+Pin# Symbol Pin# Symbol Pin# Symbol 1 GND 12 GND 23 B3 2 DOTCLK 13 G0 24 B4 3 NC 14 G1 25 B5 4 NC 15 G2 26 GND 5 GND 16 G3 27 DE 6 R0 17 G4 28 VDD 7 R1 18 G5 29 VDD 8 R2 19 GND 30 R/L 9 R3 20 B0 31 U/D 10 R4 21 B1 32 NC 11 R522B233GNDLED Backlight Unit (CN2): Backlight Connector:ManufacturerJSTConnector Model Number SM06B-SRKS-G-TBcompatible with JST SM06B-SRSS-TB (LS) (SN)Mating Connecter Model Number JST SHR-06V-BKHF-B or compatiblePin # Symbol Pin # Symbol 1 V LED 4 GND 2 V LED 5 PWM DIM 3GND6LED ON/OFFLED Light Bar Input (CN3): Light Bar Connector ManufacturerSTM or compatible Connector Model Number P24021P6 or compatible Mating Connecter Model NumberSM06B-SHLS-TF or compatiblePin # Symbol Pin Description Cable color1 AN1 Channel 1 LED anode Red2 AN2 Channel 2 LED anode Red3 AN3 Channel 3 LED anode Red4 CA1 Channel 1 LED cathode White5 CA2 Channel 2 LED cathode Blue6 CA3Channel 3 LED cathodeBlack工业液晶屏ｗｗｗ．ｈｚｘｕｈｏｎｇ．ｃｏｍReliability Test Criteria: ItemsRequired Condition Remark Temperature Humidity Bias40℃/90%,300HrNote 2 High Temperature Operation 85℃,300Hr Note 2 Low Temperature Operation -30℃,300Hr Note 2 High Temperature Storage 85℃,300 hours Note 2 Low Temperature Storage -30℃,300 hoursNote 2 Thermal Shock Test -20℃/30 min ,60℃/30 min ,100cyclesNote 2 Hot Start Test 85℃/1 Hr (min.), power on/off per 5 minutes, repeat 5 times Note 2 Cold Start Test -30℃/1 Hr (min.), power on/off per 5 minutes, repeat 5 times Note 2 Shock Test (Non-Operating) 50G, 20ms,Half-sine wave, (±X, ±Y , ±Z)Note 2Vibration Test (Non-Operating)(1)Random Wave 3.3rms, 0.5hr(X,Y,Z), 5~500hz (2)Sine Wave 6.8G, 10~400hz, 4hr40min (XYZ)Note 2ESDContact Discharge: ±8KV, 150pF(330Ω) 1sec, 8 points, 25times/pointAir Discharge: ±15KV, 150pF(330Ω) 1sec, 8 points, 25 times/pointNote 1,2Attitude TestOperating: 14,000 ft, Ramp: 2000 ft/min, 8hrs Non-operating: 40,000 ft, Ramp: 2000 ft/min, 24hrsNote 2Note1: According to EN61000-4-2 ESD class B criteria, some performance degradation is allowed. TFT-LCD module is self-recoverable, no data lost and no hardware failures after test. Note2:Water condensation is not allowed for each test items.Each test is done by new TFT-LCD module. Don’t use the same TFT-LCD module repeatedly for reliability test.The reliability test is performed only to examine the TFT-LCD module capability.To inspect TFT-LCD module after reliability test, please store it at room temperature and room humidity for 24 hours at least in advance.工业液晶屏ｗｗｗ．ｈｚｘｕｈｏｎｇ．ｃｏｍVersion 0.2, Mar 2012Mechanical Characteristics:工业液晶屏ｗｗｗ．ｈｚｘｕｈｏｎｇ．ｃｏｍ。
MY-TFT070V2产品用户手册说明书
MY-TFT070V2 产品用户手册版本V1.12015年3月16日版本记录目录目录 (1)第1章产品概述 (2)1.1 产品简介 (2)1.2 规格参数 (2)1.3 产品预览 (3)第2章硬件指南 (5)2.1 引脚分布 (5)2.2 信号定义 (5)2.3 电气特性 (6)2.4 时序参数 (7)第3章机械参数 (10)附录 (12)附录一联系方式 (13)附录二售后服务与技术支持 (14)第1章产品概述1.1 产品简介MY-TFT070V2是深圳米尔科技有限公司推出的7寸液晶模块，是彩色有源矩阵薄膜晶体管（TFT）液晶显示器（LCD），由TFT LCD显示器件，连接件，控制与驱动外围电路，PCB驱动底板等组成，驱动底板预留1.27mm间距的IDC排线插针(25pinX2）和0.5mm 间距的FPC连接器两种连接方式，是专为米尔科技ARM主板设计的配套LCD液晶显示模块。
1.2 产品特性MY-TFT070V2兼容三种触摸输入方式，分别为电阻式触摸输入、电容式触摸输入和外置式输入，可以根据需要任意选用需要的方式，同时只能有一种触摸方式被连接。
图1-1MY-TFT070V2带有一颗存储芯片，用来保存LCD的一些常规信息，MYiR的开发板系统能够版识别MY-TFT070V2，并根据这些信息来加载相应的驱动。
1.3 规格参数1.4 产品预览MY-TFT070V2 产品平面图如图1-2、图1-3所示：图1-2 MY-TFT070V2产品正面图图1-3 MY-TFT070V2 产品背面图第2章硬件指南2.1 接口分布底板接口分布如下图2-1所示：图2-1 底板接口分布图如上图所示，驱动底板预留1.27mm间距的50pin IDC排线插针(J1）和0.5mm间距的50pin FPC连接器（J2）两种连接方式，默认连接50pin IDC排线。
J4为电阻触摸信号连接，J5，J7分别为电容触摸控制信号连接，默认选择J5电容触摸模式。
C103VAN01.1规格书Product Spec_v02_20160127-杭州旭虹科技有限公司
Model Name:
Planned Lifetime: Phase-out Control: EOL Schedule:
< From
C103VAN01.1
2016/Jan To 2019/Dec From 2019/Apr To 2019/Dec 2019/Apr
工业液晶屏ｈｔｔｐ：／／ｗｗｗ．ｈｚｘｕｈｏｎｇ．ｃｏｍ
杭州旭虹科技有限公司
C. Physical Specifications
F. G. H.
Optical specifications (Note 1, 2) ................................................................................ 20 Reliability Test Items (Note 2)...................................................................................... 22 Packing Form................................................................................................................ 23
杭州旭虹科技有限公司
CUSTOMER APPROVAL SHEET
Company Name MODEL CUSTOMER APPROVED
□ □ □ □
C103VAN01.1
Title :
Name :
APPROVAL FOR SPECIFICATIONS ONLY (Spec. Ver. 0.2) APPROVAL FOR SPECIFICATIONS AND ES SAMPLE (Spec. Ver. 0.2) APPROVAL FOR SPECIFICATIONS AND CS SAMPLE (Spec. Ver. 0.2) CUSTOMER REMARK :
图南光电,友达M170ETN01_1规格书
图南光电 ｈｔｔｐ：／／ｗｗｗ．ｔｎｄｉｓｐｌａｙ．ｃｏｍ．ｃｎProduct SpecificationAU OPTRONICS CORPORATIONM170ETN01.1(V ) Preliminary Specification ( ) Final Specification Module Model Name 17” Color TFT-LCD M170ETN01.1CustomerDateApproved byDateChi Yin WuFeb 6, 2013Approved byPrepared byDateJia Hau JeanFeb 6, 2013Note: This Specification is subject to change without notice.AU Optronics corporationdocument version 0.01图南光电 ｈｔｔｐ：／／ｗｗｗ．ｔｎｄｉｓｐｌａｙ．ｃｏｍ．ｃｎProduct SpecificationAU OPTRONICS CORPORATIONM170ETN01.1Contents 1 Handling Precautions................................................................4 2 General Description ..................................................................52.1 Display Characteristics....................................................................................................... 5 2.2 Absolute Maximum Rating of Environment ........................................................................ 6 2.3 Optical Characteristics ....................................................................................................... 73 TFT-LCD Module ......................................................................113.1 Block Diagram.................................................................................................................. 11 3.2 Interface Connection........................................................................................................ 12 3.2.1 Connector Type....................................................................................................... 12 3.2.2 Connector Pin Assignment...................................................................................... 12 3.3 Electrical Characteristics.................................................................................................. 14 3.3.1 Absolute Maximum Rating ...................................................................................... 14 3.3.2 Recommended Operating Condition....................................................................... 14 3.4 Signal Characteristics ...................................................................................................... 15 3.4.1 LCD Pixel Format.................................................................................................... 15 3.4.2 LVDS Data Format .................................................................................................. 15 3.4.3 Color versus Input Data .......................................................................................... 16 3.4.4 LVDS Specification.................................................................................................. 17 3.4.5 Input Timing Specification ....................................................................................... 19 3.4.6 Input Timing Diagram .............................................................................................. 20 3.5 Power ON/OFF Sequence ............................................................................................... 214 Backlight Unit .........................................................................224.1 Block Diagram.................................................................................................................. 22 4.2 Interface Connection........................................................................................................ 23 4.2.1 Connector Type....................................................................................................... 23 4.2.2 Connector Pin Assignment...................................................................................... 25 4.3 Electrical Characteristics.................................................................................................. 26 4.3.1 Absolute Maximum Rating ...................................................................................... 26 4.3.2 Recommended Operating Condition....................................................................... 265 6 7 8Reliability Test ........................................................................28 Shipping Label ........................................................................29 Mechanical Characteristics .....................................................30 Packing Specification..............................................................318.1 Packing Flow.................................................................................................................... 31 8.2 Pallet and shipment information....................................................................................... 32document version 0.02图南光电 ｈｔｔｐ：／／ｗｗｗ．ｔｎｄｉｓｐｌａｙ．ｃｏｍ．ｃｎProduct SpecificationAU OPTRONICS CORPORATIONM170ETN01.1Record of RevisionVersion Date Page Old description New Description Remark0.02013/2/6AllFirst version release-document version 0.03Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.11 Handling Precautions 1) 2) 3) 4) 5) 6) 7) 8) 9) Since front polarizer is easily damaged, pay attention not to scratch it. Be sure to turn off power supply when inserting or disconnecting from input connector. Wipe off water drop immediately. Long contact with water may cause discoloration or spots. When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. Do not open or modify the Module Assembly. Do not press the reflector sheet at the back of the module to any directions. In case a TFT-LCD Module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the LED lightbar edge. Otherwise the TFT-LCD Module may be damaged. Insert or pull out the interface connector, be sure not to rotate nor tilt it of the TFT-LCD Module. Do not twist nor bend the TFT -LCD Module even momentary. It should be taken into consideration that no bending/twisting forces are applied to the TFT-LCD Module from outside. Otherwise the TFT-LCD Module may be damaged. Please avoid touching COF position while you are doing mechanical design. When storing modules as spares for a long time, the following precaution is necessary: Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5℃ and 35℃ at normal humidity.10) 11)12) 13)document version 0.04Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.12 General Description This specification applies to the 17 inch wide Color a-Si TFT-LCD Module M170ETN01.1. The display supports the SXGA+ (1280(H) x 1024(V)) screen format and 16.7M colors (RGB 6-bits + Hi-FRC data). The input interface is Dual channel LVDS and this module doesn’t contain an driver board for backlight.2.1 Display Characteristics The following items are characteristics summary on the table under 25℃ condition:ITEMS Screen Diagonal Active Area Pixels H x V Pixel Pitch Pixel Arrangement Display Mode White Luminance ( Center ) Contrast Ratio Response Time Power Consumption (LCD Module + Backligh unit) Weight Outline Dimension Electrical Interface Support Color Surface Treatment Temperature Range Operating Storage (Shipping) RoHS Compliance TCO Compliance Unit [mm] [mm] [mm] [cd/m2] [msec] [Watt] SPECIFICATIONS 432 (17.0”) 337.920(H) × 270.336(V) 1280 × 3(RGB) × 1024 0.264(per one triad) × 0.264 R.G.B. Vertical Stripe Normally White 250 (Typ.) 1000 : 1 (Typ.) 5 (Typ., on/off) 9.91 (Typ.) LCD module : PDD (Typ.)=3 @ Black pattern,Fv=60Hz Backlight unit : PBLU (Typ.) =6.91 @Is=60mA 1273 (Typ.) 358.5(H) x 296.5(V) x 10.3(D) (Typ.) Dual Channel LVDS 16.7M colors (RGB 6-bits +Hi-FRC data) Anti-glare type, Hardness 3H 0 to +50 -20 to +60 RoHS Compliance TCO6.0 Compliance[Grams] [mm] [oC] [oC] -document version 0.05Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.12.2 Absolute Maximum Rating of Environment Permanent damage may occur if exceeding the following maximum rating. Symbol TOP TGS HOP TST HST Description Operating Temperature Glass surface temperature (operation) Operation Humidity Storage Temperature Storage Humidity Min. 0 0 5 -20 5 Max. +50 +65 90 +60 90 Unit [ C] [ C] [%RH] [oC] [%RH]o oRemark Note 2-1 Note 2-1Function judged onlyNote 2-1Note 2-1: Temperature and relative humidity range are shown as the below figure. 1. 90% RH Max ( Ta ≦39℃) 2. Max wet-bulb temperature at 39℃ or less. ( Ta ≦39℃) 3. No condensationOperating RangeStorage Rangedocument version 0.06Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.12.3 Optical Characteristics The optical characteristics are measured on the following test condition. Test Condition: 1. Equipment setup: Please refer to Note 2-2. 2. Panel Lighting time: 30 minutes 3. VDD=5.0V, Fv=60Hz,Is=60mA,Ta=25℃Symbol Description White Luminance (Center of screen) Min. 200 75 600 75 75 70 70 75 75 70 70 TBD TBD TBD TBD TBD TBD Typ. 250 80 1000 85 85 80 80 88 88 85 85 3.8 1.2 5 TBD TBD TBD TBD TBD TBD Max. 5.5 2.5 8 TBD TBD TBD TBD TBD TBD By SR-3 [msec] Note 2-6 By TRD-100 [degree] Note 2-5 By SR-3 Unit[cd/m2]Remark Note 2-2 By SR-3 Note 2-3 By SR-3Lw Luni CR θR θL ΦH ΦL θR θL ΦH ΦL TR TF Rx Ry Gx Gy Bx By Wx Wy CT FdBLuminance Uniformity (9 points) Contrast Ratio (Center of screen) Horizontal Viewing Angle (CR=10) Vertical Viewing Angle (CR=10) Horizontal Viewing Angle (CR=5) Vertical Viewing Angle (CR=5) Right Left Up Down Right Left Up Down Rising Time Response Time Falling Time Rising + Falling Red x Red y Green x Color Coordinates (CIE 1931) Green y Blue x Blue y White x White y Crosstalk Flicker (Center of screen)[%]-Note 2-4 By SR-30.283 0.313 0.343 0.299 0.329 0.359 1.5 -20 [%] [dB] Note 2-7 By SR-3 Note 2-8 By SR-3document version 0.07Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.1Note 2-2: Equipment setup :Photo detector (SR-3, TRD-100)Measured distance (50cm)LCD PanelTFT-LCD ModuleCenter of the screen Note 2-3: Luminance Uniformity Measurement Definition:Luminance Uniformity =Minimum Luminance of 9 Points (P1 ~ P9) Maximum Luminance of 9 Points (P1 ~ P9)a.Test pattern: White Patterndocument version 0.08Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.1Note 2-4: Contrast Ratio Measurement Definition:Contrast Ratio =Luminance of White pattern Luminance of Black patterna. Measured position: Center of screen (P5) & perpendicular to the screen (θ=Φ=0°) Note 2-5: Viewing angle measurement Definition: The angle at which the contrast ratio is greater than 10 & 5 . a. Horizontal view angle: Divide to left & right (θL & θR) Vertical view angle: Divide to up & down (ΦH &ΦL)Note 2-6: Response time measurement The output signals of photo detector are measured when the input signals are changed from “Black” to “White” (rising time, TR), and from “White” to “Black” (falling time, TF), respectively. The response time is interval between the 10% and 90% of optical response. (Black & White color definition: Please refer section 3.4.3)%TFTR100 90 Optical response 10 0 1 Frame 1 Frame White Black B lack W hitedocument version 0.09Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.1Note 2-7: Crosstalk measurement Definition: CT = Max. (CTH,CTV); Where a.Maximum Horizontal Crosstalk : CTH = Max. (| YBL – YAL | / YAL × 100 %, | YBR – YAR | / YAR × 100 %); Maximum Vertical Crosstalk: CTV = Max. (| YBU – YAU | / YAU × 100 %, | YBD – YAD | / YAD × 100 %); b. YAU, YAD, YAL, YAR = Luminance of measured location without Black pattern YBU, YBD, YBL, YBR = Luminance of measured location with Black patternNote 2-8: Flicker measurement a. Test pattern: It is listed as following. Gray level = L0Gray level = L127R: Red, G: Green, B:Blue b. Measured position: Center of screen (P5) & perpendicular to the screen (θ=Φ=0°)document version 0.010Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.13 TFT-LCD Module 3.1 Block Diagram The following shows the block diagram of the 17 inch Color TFT-LCD Module.ConnectorLVDS Signal Signal VDDDC/DCConverterGamma Correction G1 D1 X-Driver IC D3840AUO ASICTiming Controller Mini LVDS TransmitterTFT-LCD1280(x3) x 1024 Pixels G1024LVDSReceiverASIC Control Boarddocument version 0.011Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.13.2 Interface Connection 3.2.1 Connector Type Manufacturer Part Number Mating Connector Manufacturer Part Number P-TWOAL230F-A0G1D-PTFT-LCD ConnectorSTMMSCKT2407P30HBJAEFI-XB30SSRLAHF16JAE FI-X30HL (Locked Type)3.2.2 Connector Pin Assignment PIN # 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Symbol RxO0RxO0+ RxO1RxO1+ RxO2RxO2+ GND RxOCLKRxOCLK+ RxO3RxO3+ RxE0RxE0+ GND RxE1RxE1+ GND RxE2RxE2+ RxECLKRxECLK+ RxE3RxE3+ GND NC NC Description Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Ground Negative LVDS differential clock input (Odd clock) Positive LVDS differential clock input (Odd clock) Negative LVDS differential data input (Odd data) Positive LVDS differential data input (Odd data) Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Ground Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Ground Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Negative LVDS differential clock input (Even clock) Positive LVDS differential clock input (Even clock) Negative LVDS differential data input (Even data) Positive LVDS differential data input (Even data) Ground No connection (for AUO test only. Do not connect) No connection (for AUO test only. Do not connect)12Remarkdocument version 0.0Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.127 28 29 30NC VDD VDD VDDNo connection (for AUO test only. Do not connect) Power Supply Input Voltage Power Supply Input Voltage Power Supply Input Voltagedocument version 0.013Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.13.3 Electrical Characteristics 3.3.1 Absolute Maximum Rating Permanent damage may occur if exceeding the following maximum rating. Symbol VDD Description Power Supply Input Voltage Min GND-0.3 Max 6.0 Unit [Volt] Remark Ta=25℃3.3.2 Recommended Operating Condition Symbol VDD IDD PDD IRush VDDrp Description Power supply Input voltagePower supply Input Current (RMS)Min 4.5 -Typ 5.0 0.6 0.72 3 3.6Max 5.5 0.72 0.87 3.6 4.32 3.0 500Unit [Volt] [A] [A]RemarkVDD= 5.0V, Black Pattern, Fv=60Hz VDD= 5.0V, Black Pattern, Fv=75HzVDD Power Consumption Inrush Current Allowable VDD Ripple Voltage[Watt] VDD= 5.0V, Black Pattern, Fv=60Hz [Watt] VDD= 5.0V, Black Pattern, Fv=75Hz [A] Note 3-1--[mV] VDD= 5.0V, Black Pattern, Fv=75HzNote 3-1: Inrush Current measurement: Test circuit:The duration of VDD rising time: 470us.document version 0.0 14Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.13.4 Signal Characteristics 3.4.1 LCD Pixel Format1 1st Line 2 1279 1280 R G B R G BR G B R GB1024th Line R G B R G BR G B R G B3.4.2 LVDS Data FormatNote 3-2: a. O = “Odd Pixel Data” E = “Even Pixel Data” nd b. Refer to 3.4.1 LCD pixel format, the 1st data is 1 (Odd Pixel Data), the 2 data is 2 (Even Pixel Data) and the last data is 1280 (Even Pixel Data).document version 0.015Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.13.4.3 Color versus Input Data The following table is for color versus input data (8bit). The higher the gray level, the brighter the color.document version 0.016Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.13.4.4 LVDS Specification a. DC Characteristics: Symbol VTH VTL │VID│ VCM Description LVDS Differential Input High Threshold LVDS Differential Input Low Threshold LVDS Differential Input Voltage LVDS Common Mode Voltage Min -100 100 +1.0 Typ +1.2 Max +100 600 +1.5 Units [mV] [mV] [mV] [V] VTH-VTL = 200mV Condition VCM = 1.2V VCM = 1.2VLVDS Signal Waveform: Use RxOCLK- & RxOCLK+ as example.RxOCLK-RxOCLK+document version 0.017Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.1b. AC Characteristics: Symbol Description Maximum deviation of input clock frequency during Spread Spectrum FMOD Maximum modulation frequency of input clock during Spread Spectrum 200 KHz Min Max Unit RemarkFDEV-±3%Freq Fmax Fclk * FDEV Fclk Fmin 1 FMOD < Spread Spectrum> TimeFclk: LVDS Clock Frequencydocument version 0.018Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.13.4.5 Input Timing Specification It only support DE mode, and the input timing are shown as the following table. Symbol Tv Tdisp (v) Tblk (v) Fv Th Tdisp (h) Tblk (h) Fh Tclk Fclk LVDS Clock Horizontal Section Vertical Section Description Period Active Blanking Frequency Period Active Blanking Frequency Period Frequency Min. 1036 1024 12 50 730 640 90 37.8 50 51.8 Typ. 1066 1024 42 60 844 640 204 54 60 64 Max. 1873 1024 849 76 1320 640 680 68.4 76 93.7 Unit Th Th Th Hz Tclk Tclk Tclk KHz ns MHz Note 3-3 1/Fclk Note 3-4 RemarkNote 3-3: The equation is listed as following. Please don’t exceed the above recommended value. Fh (Min.) = Fclk (Min.) / Th (Min.); Fh (Typ.) = Fclk (Typ.) / Th (Typ.); Fh (Max.)= Fclk (Max.) / Th (Min.); Note 3-4: The equation is listed as following. Please don’t exceed the above recommended value. Fclk (Min.) = Fv (Min.) x Th (Min.) x Tv (Min.); Fclk (Typ.) = Fv (Typ.) x Th (Typ.) x Tv (Typ.); Fclk (Max.) = Fv (Max.) x Th (Typ.) x Tv (Typ.);document version 0.019Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.13.4.6 Input Timing DiagramTv M pixel Tblk(v) Tdisp(v) Y Th N LineXDEN RGB DataLineInvalid Data1Line2Line3Line4LineNLineInvalid DataCLKTclkThTdisp(h)Tblk(h)DERGB Data Pixel Pixel Pixel Pixel (Odd) M-7 M-5 M-3 M-1Invalid DataPixel Pixel Pixel Pixel Pixel Pixel 1 3 5 7 9 11Pixel Pixel Pixel M-5 M-3 M-1Invalid DataPixel Pixel 1 3RGB Data Pixel Pixel Pixel Pixel (Even) M-6 M-4 M-2 MInvalid DataPixel Pixel Pixel Pixel Pixel Pixel 2 4 6 8 10 12PixelPixel M-4PixelM-2 MInvalid DataPixel Pixel 2 4document version 0.020Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.13.5 Power ON/OFF Sequence VDD power,LVDS signal and backlight on/off sequence are as following. LVDS signals from any system shall be Hi-Z state when VDD is off.Backlight OffT190% 90% 10%VDD10%T2T5T6T7LVDS SignalVALID DATA T3 T4 Backlight On Backlight OffVSLEDBacklight OffPower Sequence TimingSymbol Min.T1 T2 T3 T4 T5 T6 T7 0.5 0 500 100 0 0 1000Value Typ.-Max.10 50 50Unit[ms] [ms] [ms] [ms] [ms] [ms] [ms]RemarkNote 3-5 Note 3-6 Note 3-6-150 -Note 3-5 : Recommend setting T5 = 0ms to avoid electronic noise when VDD is off. Note 3-6 : During T5 and T6 period , please keep the level of input LVDS signals with Hi-Z state.document version 0.021Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.14 Backlight Unit 4.1 Block Diagram The following shows the block diagram of the 17 inch Backlight Unit. And it includes 36 pcs LED in the LED light bar. (4 strings and 9 pcs LED of one string).+ VS -ISISISISConnectorVSLEDCh1Ch2Ch3Ch4document version 0.022Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.14.2 Interface Connection 4.2.1 Connector Type Manufacturer Backlight Connector Part Number Manufacturer Mating Connector Part Number H112K-P06N-13B (Locking type) 3707K-S06N-21R ENTERY ENTERYBacklight Connector dimension:H × V × D = 13.9 × 3.00 × 4.25, Pitch = 1.0(unit = mm )document version 0.023Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.1Mating Connector dimension:document version 0.024Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.14.2.2 Connector Pin Assignment Pin# 1 2 3 4 5 6 Symbol Ch1 Ch2 VSLED VSLED Ch3 Ch4 Description LED Current Feedback Terminal (Channel 1) LED Current Feedback Terminal (Channel 2) LED Power Supply Voltage Input Terminal LED Power Supply Voltage Input Terminal LED Current Feedback Terminal (Channel 3) LED Current Feedback Terminal (Channel 4) RemarkPIN1document version 0.025Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.14.3 Electrical Characteristics 4.3.1 Absolute Maximum RatingPermanent damage may occur if exceeding the following maximum rating. (Ta=25 ) Remark100% duty ratio Duty ratio 10% Pulse time=10 msSymbol IsDescription LED String CurrentMin 0Max 90 150Unit [mA] [mA]℃≦Duty ratio= (A / B) X 100% ;(A: Pulse time, B: Period)4.3.2 Recommended Operating Condition (Ta=25℃)Symbol Description Min. Typ. Max. Unit Remark 100% duty ratio of LED chip Is=60mA @ 100% duty ratio; Note 4-1 Is=60mA @ 100% duty ratio; Note 4-2Is Vs ∆Vs PBLU LTLEDLED String Current LED String Voltage Maximum Vs Voltage Deviation of light bar LED Light Bar Power Consumption LED Life Time25.260 28.8 6.91 -66 32.4 1.8 8.55 -[mA] [Volt] [Volt] [Watt] [Hour]30,000Note 4-3 Note 4-4document version 0.026Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.1Note 4-1: Vs (Typ.) = VF (Typ.) X LED No. (one string); a. VF: LED chip forward voltage, VF (Min.)=2.8V, VF(Typ.)=3.2V, VF(Max.)=3.6V b. The same euqation to calculate Vs(Min.) & Vs (Max.) for respective VF (Min.) & VF(Max.);Note 4-2: ∆Vs (Max.) = ∆VF X LED No. (one string); a. ∆VF: LED chip forward voltage deviation; (0.2 V , each Bin of LED VF) Note 4-3: PBLU (Typ.) = Vs (Typ.) X Is (Typ.) X 4 ; ( 4 is total String No. of LED Light bar) PBLU (Max.) = Vs (Max.) X Is (Max.) X 4 ; Note 4-4: Definition of life time: a. Brightness of LED becomes to 50% of its original value b. Test condition: Is = 60mA and 25℃ (Room Temperature)document version 0.027Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.15 Reliability Test AUO reliability test items are listed as following table. (Bare Panel only) ItemsTemperature Humidity Bias (THB) High Temperature Operation (HTO) Low Temperature Operation (LTO) High Temperature Storage (HTS) Low Temperature Storage (LTS) Vibration Test (Non-operation)ConditionTa= 50℃, 80%RH, 300hours Ta= 50℃, 50%RH, 300hours Ta= 0℃, 300hours Ta= 60℃, 300hours Ta= -20℃, 300hours Acceleration: 1.5 Grms Wave: Random Frequency: 10 - 200 Hz Sweep: 30 Minutes each Axis (X, Y, Z) Acceleration: 50 G Wave: Half-sine Active Time: 20 ms Direction: ±X, ±Y, ±Z (one time for each Axis) Height: 61 cm, package test -20℃/30min, 60℃/30min, 100 cycles On/10sec, Off/10sec, 30,000 cycles Contact Discharge: ± 15KV, 150pF(330Ω ) 1sec, 8 points, 25 times/ point.RemarkShock Test (Non-operation) Drop Test Thermal Shock Test (TST) On/Off TestNote 5-1ESD (Electro Static Discharge) Air Discharge: ± 15KV, 150pF(330Ω ) 1sec 8 points, 25 times/ point. Altitude Test Operation:18,000 ft Non-Operation:40,000 ftNote 5-2Note 5-1: a. A cycle of rapid temperature change consists of varying the temperature from -20℃ to 60℃, and back again. Power is not applied during the test. b. After finish temperature cycling, the unit is placed in normal room ambient for at least 4 hours before power on. Note 5-2: EN61000-4-2, ESD class B: Certain performance degradation allowed No data lost Self-recoverable No hardware failures.document version 0.028Product SpecificationAU OPTRONICS CORPORATIONM170ETN01.16 Shipping Label The label is on the panel as shown below:M170ETN01.1Note 6-1: For Pb Free products, AUO will addfor identification. for identification. for identification.Note 6-2: For RoHS compatible products, AUO will addNote 6-3: For China RoHS compatible products, AUO will addNote 6-4: The Green Mark will be presented only when the green documents have been ready by AUO Internal Green Team.document version 0.0297 Mechanical CharacteristicsAvoid touching COF position when doing mechanical designVer 0.08 Packing Specification 8.1 Packing Flow面板依序貼附保護膜裝入靜電袋， 面板依序貼附保護膜裝入靜電袋，P 板朝上依序放入紙箱中， 板朝上依序放入紙箱中，滿箱裝 8pcsCorner angle Stretch filmMoisture-proof filmLabelPET bandCorner anglePalletVer 0.08.2 Pallet and shipment informationSpecification Item Q'ty Panel Cushion Box Packing Box Pallet 1 1 1 8 pcs/Box 1 Dimension 358.5(H)mm × 296.5(V)mm × 10.3(D)mm 434(L)mm x 278(W)mm x 390(H)mm 434(L)mm x 278(W)mm x 390(H)mm 1150(L)mm x 890(W)mm x 132(H)mm 1150(L)mm x 890(W)mm x 131(H)mm Weight(kg) 1.45 0.95 0.90 13.45 12.00 334.8 without Panel & cushion with panel & cushion RemarkPallet after Packing 18 boxes/palletVer 0.0。
14350074 7寸液晶屏(KD070D10-50NB-A5)(备注：国显)(分辨率：800X480)
深圳市国显科技有限公司Shenzhen K&D Technology Co.,LtdSPECIFICATIONFORLCD MODULECustomer:Product Model: KD070D10-50NB-A5Sample code:Approved byDesigned by Checked by Array※The specification of “TBD” should refer to the measured value of sample . If there is difference between the design specification and measured value, we naturally shall negotiate and agree toRevision HistoryVersion Contents Date NoteA Original 2012-5-5B Add the specification of backlight 2012-10-9ContentsNo. Item Page1. Numbering System 4/262 Scope 5/263 Normative Reference 5/264 Definitions5/265 Technology Specifications7/266 Circuit block diagram 14/267 Reliability Test Condition and Methods 16/268 Inspection standard17/269 Handling Precautions23/2610 Precaution for use24/2611 Dimensional Outline25/2612 Packaging Drawing 26/261 Numbering System— (1) (2) (3) (4) (5) (6) (7) （8）2 ScopeThis specification applies to the TFT LCD module which is designed and manufactured by LCM Factory of Shenzhen K&D Technology Co.,Ltd.3 Normative ReferenceGB/T4619-1996 《Liquid Crystal Display Test Method》GB/T2424 《Basic environmental Testing Procedures for Electric and Electronic Products.》GB/T2423 《Basic Testing Procedures for Electric and Electronic Products》IEC61747-1 《SIXTH PARTGB2828`2829-87《National Standard of PRC》4 Definitions4.1 Definitions of VopThe definitions of threshold voltage Vth1, Vth2 the following typical waveforms are applied on liquid crystal by the method of equalized voltage for each duty and bias.【 selected waveform 】【 non-selected waveform 】① Vth1: The voltage which the brightness of segment indicates 50% of saturated value on the conditions of selected waveform(f f=80Hz, Φ=10°θ=270° at 25℃)② Vth2: The voltage which the brightness of segment indicates 50% of saturated value on the conditions of non-selected waveform(f f=80Hz, Φ=10°θ=270° at 25℃)③ Vop: (Vth1(50%)+Vth2(50%))/2 (f f=80Hz, Φ=10°θ=270° at 25℃)4.2 Definition of Response Time Tr, TdTr: The time required which the brightness of segment①becomes 10% from 100% when waveform is switched toselected one from non-selected one. (f f=80Hz, Φ=10°θ=270° at 25℃)②ss of segmentTd: The time required which the brightneselected one from selected one. (f f=80Hz, Φ=10°θ=270° at25℃)4.3 Definition of Contrast Ratio CrCr=A/B① A: Segments brightness in case of non-selected waveform② B: Segments brightness in case of selected waveform4.4 Definition of Angle and Viewing RangeAngular Graph: Constrast RatioSuch as:Viewing Angle Range:80(Cr>2) Horizontal70(Cr>2) Vertical5 Technology Specifications5.1 FeatureThis single-display module is suitable for use in Multidedia Player products. The LCD adopts one backlight with High brightness 18-lamps white LED.1) Construction: 7〞а-Si color TFT-LCD ,White LED backlight and FPC. 2) LCD:2.1 Amorphous-TFT 7-inch display, transmissive, normally white type. 2.2 800(RGB)×480 dots Matrix. 2.3 Narrow-contact ledge technique. 3) RGB interface.4) Video signal interface: Parallel RGB.5.2 Mechanical SpecificationsItem Specifications UnitDimensional outline 164.9(W) ×100.0(H) ×3.4(D) mmActive area 154.08(W) × 85.92(H) mm Pixel size 63.2(W) ×RGB×179(H) um Resolution 800(RGB) ×480 pixelLuminance250（TYP ） cd/m25.3 Absolute Max. RatingItem Symbol ValuesUnit RemarkMin. MaxPower voltageDV DD -0.5 5.0 V AV DD -0.5 15 VV GH -0.3 40 V V GL -20 0.3 V Operation temperature T OP -10 60 ℃ Storage temperatureT ST -20 70 ℃Note: The absolute maximum rating values of this product not allowed to be exceeded at any times. Should be module be used with any of absolute maximum ratings exceeded. The characteristics of the module may not be recovered, or in an extreme case, the module may be permanently destroyed.5.4 Electrical Characteristics Note 1Item SymbolValuesUnit Remark Min. Typ MaxPower voltage DV DD 3.0 3.3 3.6 V Note2 AV DD 10.1 10.3 10.5 VV GH 17.5 18 18.5 VV GL -8.5 -8 -7.5 VInput signal voltage V COM 3.1 3.3 3.4 VInput logic high voltage V IH 0.7DV DD- DV DD VNote 3 Input logic low voltage V IL 0 -0.3DV DD VNote 1:Be sure to apply DV DD and V GL to the LCD first, and then apply V GH . Note 2: DV DD setting should match the signals output voltage(refer to Note 3) of Customer’s system board.Note 3: DCLK,HS.VS,RESET,U/D,L/R,DE,R0-R7,G0-G7, G0-G7,MODE,DITHB.5.5 Optical specificationsItem Symbol ConditionValuesUnit Remark Min. Typ. Max.Viewing angle (CR≥ 10) θLΦ=180°(9o’clock)70 80 -degreeNote 1 θRΦ=0°(3 o’clock)70 80 -θTΦ=90°(12o’clock)60 70 -θBΦ=270°(6o’clock)65 75 -ResponsetimeT ONNormalθ=Φ=0° - 10 20msecNote3T OFF -1530msecNote3Contrast ratio CR 350500--Note4Color chromaticity W X 0.249 0.2990.349- Note 2Note 5Note 6 W Y 0.281 0.3310.381-Luminance L 200250 -cd/m2Note6Luminance uniformity Y U 70 80 - % Note6,7Test Conditions:1. DVDD=3.3V, I LED=120mA, the ambient temperature is 25.℃2. The test systems refer to Note 2.Note 1: Definition of viewing angle rangeNote 2: Definition of optical measurement system.The optical characteristics should be measured in dark room. After 30minutes operation, the optical properties are measured at the center point of the LCD screen. (Viewing angle is measured by ELDIM-EZ contrast/Height :1.2mm ,Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/ Field of view: 1° /Height: 500mm.)Normal line Φ=270°6 o’clock direction Φ=0°Φ=180°Φ=270° 6 o’clock direction Φ=0°ΦNormal line θ=Φ=0°Note 3: Definition of Response timeThe response time is defined as the LCD optical switching time intervalbetween “White” state and “Black” state. Rise time (T ON ) is the time between photo detector output intensity changed from 90% to 10%. And fall time (T OFF ) is the time between photo detector output intensity changed from 10% to 90%.Note 4: Definition of contrast ratiostate Black"" the on LCD when measured Luminance state White"" the on LCD when measured Luminance (CR) ratio Contrast =Note 5: Definition of color chromaticity (CIE1931)Color coordinates measured at center point of LCD.Note 6: All input terminals LCD panel must be ground while measuring the centerarea of the panel. The LED driving condition is I LED =180mA.Note 7: Definition of Luminance UniformityActive area is divided into 9 measuring areas. Every measuring point is placed at the center of each measuring area.max minB B(Yu)Uniformity Luminance = L-------Active area length W----- Active area widthB max : The measured maximum luminance of all measurement position. B min : The measured minimum luminance of all measurement position.90%10% 0%P h o t o d e t e c t o r o u t p u t (R e l a t i v e v a l u e )ONWhite (TFT OFF)Black (TFT ON)White (TFT OFF)5.6 LED back light specification (18 White Chips)UnitMaxTypItem Symbol Condition Min=120mA9 9.6 9.9 V Forward Voltage Vf lf=120mA80 - - % Uniformity (with L/G) ΔB p lf5.7 Interface Pin ConnectionsPinSymbol I/O Function Remark No.1 VLED+ P Power for LED Backlight(Anode)2 VLED+ P Power for LED Backlight(Anode)3 VLED- P Power for LED Backlight(Cathode)4 VLED- P Power for LED Backlight(Cathode)ground5 GND PPowervoltageCommon6 V COM I7 DV DD P Power for Digital Circuit8 MODE I DE/SYNC mode select Note 1EnableInput9 DE IData10 VS I Vertical Sync Input11 HS IInputSyncHorizontalBluedata(MSB)12 B7 IBluedata13 B6 IdataBlue14 B5 IdataBlue15 B4 IBluedata16 B3 Idata17 B2 IBlue18 B1 I Blue data Note 219 B0 I Blue data(LSB) Note 2Greendata(MSB)20 G7 Idata21 G6 IGreen22 G5 IdataGreendata23 G4 IGreenGreendata24 G3 Idata25 G2 IGreen26 G1 I Green data Note 227 G0 I Green data(LSB) Note 2data(MSB)Red28 R7 Idata29 R6 IRedReddata30 R5 IdataRed31 R4 Idata32 R3 IRedReddata33 R2 I34 R1 I Red data Note 235 R0 I Red data(LSB) Note 2PowerGround36 GND P37 DCLK I Sample clock Note 3PowerGround38 GND P39 L/R I Left / right selection Note 4,540 U/D I Up/down selection Note 4,541 V GH P Gate ON VoltageVoltage42 V GL P GateOFF43 AV DD P Power for Analog Circuit44 RESET I Global reset pin. Note 6connection45 NC -NoCommonVoltage46 V COM I47 DITHB I Dithering function Note 7PowerGround48 GND PconnectionNo49 NC -connectionNo50 NC -I: input, O: output, P: PowerNote 1: DE/SYNC mode select. Normally pull high.When select DE mode, MODE=”1”, VS and HS must pull high.When select SYNC mode,MODE=”0”, DE must be grounded.Note 2: When input 18 bits RGB data, the two low bits of R,G and B data must be grounded.Note 3: Data shall be latched at the falling edge of DCLK.Note 4: Selection of scanning modeSetting of scan control inputScanning directionU/D L/R GND DV DD Up to down, left to right DV DD GND Down to up, right to left GNDGNDUp to down, right to left DV DD DV DDDown to up, left to rightNote 5: Definition of scanning direction.Refer to the figure as below:an RC reset circuit for stability. Normally pull high.Note 7: Dithering function enable control, normally pull high. When DITHB=”1”,Disable internal dithering function, When DITHB=”0”,Enable internal dithering function,6 Signal timing diagram6.2 Signal Timing Diagram6.2.1 Power ON/OFF Sequencea Power onb Power off6.2.2 Data input format6.2.3 Timing DiagramItemSymbol Values Unit RemarkMin Typ Max Horizontal Display Areathd - 800 - DCLK DCLK frequency fck - 30 50 MHz One horizontal line th 889928 1143DCLK HS pulse width thpw 1 48 255 DCLK HS Blanking thb 88 88 88 DCLK HS Front Porch thfp140255DCLK7 Reliability Test Conditions And MethodsNO Item Condition Method1 High / LowTemperatureStorage70℃/-20℃ 120hrsCheck and recordevery 48Hrs2 High / LowTemperature Life60℃/-10℃ 120hrs (operatingmode)Check and recordevery 48Hrs3 HighTemperature、High HumidityOperating60℃,90% RH, 96HrsCheck and recordevery 48hrs4 ThermalShock -20℃(30Min ) 25℃(5Min)70℃(30Min)(conversion time, : 5 sec ) 20cyclesEach 10 cycles end ,check5 StaticElectricity Gap mood: ±1KV~±8KV (10times air discharge withpositive/negative voltagevoltage gap : 1kv)Touch mood: ±1KV~±4KVEach discharge end,Check the ElectricalCharacteristics8 Inspection standardxxIntensity OfAdhesionIf lower than specification, reject Gold Fold Twist Reject07 IC/FPCBondingSiliconAccording to outline, no gold outside,seal can not be higher than LCDFPC Gold SeverReject08 SMTLack ofComponent、Polarity InverseIf exist, rejectLeak Solder、Virtual SolderIf exist, rejectShort Circuit InSolder PointIf exist, rejectTin Ball If exist, rejectTin Acumination If visual, rejectHeightSolder Point If higher 0.5mm than component. rejectHeight ofcomponentEither side higher 0.5mm thancomponent, reject9 Handling Precautions9.1 Mounting methodThe LCD panel of Daxian LCD module consists of two thin glass plates with polarizes which easily be damaged. And since the module in so constructed as to be fixed by utilizing fitting holes in the printed circuit board.Extreme care should be needed when handling the LCD modules.9.2 Caution of LCD handling and cleaningWhen cleaning the display surface, Use soft cloth with solvent[recommended below] and wipe lightlyz Isopropyl alcoholz Ethyl alcoholDo not wipe the display surface with dry or hard materials that will damage the polarizer surface.Do not use the following solvent:z Waterz AromaticsDo not wipe ITO pad area with the dry or hard materials that will damage the ITO patternsDo not use the following solvent on the pad or prevent it from being contaminated:z Soldering fluxz Chlorine (Cl) , Salfur (S)If goods were sent without being sili8con coated on the pad, ITO patterns could be damaged due to the corrosion as time goes on.If ITO corrosion happen by miss-handling or using some materials such as Chlorine (CI), Salfur (S) from customer, Responsibility is on customer.9.3 Caution against static chargeThe LCD module use C-MOS LSI drivers, so we recommended that you: Connect any unused input terminal to Vdd or Vss, do not input any signals before power is turned on, and ground your body, work/assembly areas, assembly equipment to protect against static electricity.9.4 packingz Module employ LCD elements and must be treated as such.z Avoid intense shock and falls from a height.z To prevent modules from degradation, do not operate or store them exposed direct to sunshine or high temperature/humidity9.5 Caution for operationz It is an indispensable condition to drive LCD’s within the specified voltage limit since the higher voltage then the limit cause the shorter LCD life.z An electrochemical reaction due to direct current causes LCD’s undesirable deterioration, so that the use of direct current drive should be avoided.z Response time will be extremely delayed at lower temperature then the operating temperature range and on the other hand at higher temperature LCD’s how dark color in them. However those phenomena do not meanoperation temperature.z If the display area is pushed hard during operation, some font will be abnormally displayed but it resumes normal condition after turning off once.z A slight dew depositing on terminals is a cause for electro-chemical reaction resulting in terminal open circuit.Usage under the maximum operating temperature, 50%Rh or less is required.9.6 storageIn the case of storing for a long period of time for instance, for years for the purpose or replacement use, the following ways are recommended.z Storage in a polyethylene bag with the opening sealed so as not to enter fresh air outside in it . And with no desiccant.z Placing in a dark place where neither exposure to direct sunlight nor light’s keeping the storage temperature range.z Storing with no touch on polarizer surface by the anything else.[It is recommended to store them as they have been contained in the inner container at the time of delivery from us9.7 Safetyz It is recommendable to crash damaged or unnecessary LCD’s into pieces and wash off liquid crystal by either of solvents such as acetone and ethanol, which should be burned up later.z When any liquid leaked out of a damaged glass cell comes in contact with your hands, please wash it off well with soap and water10 Precaution for use10.1A limit sample should be provided by the both parties on an occasion when the both parties agreed its necessity. Judgment by a limit sample shall take effect after the limit sample has been established and confirmed by the both parties.10.2On the following occasions, the handing of problem should be decided through discussion and agreement between responsible of the both parties.z When a question is arisen in this specificationz When a new problem is arisen which is not specified in this specificationsz When an inspection specifications change or operating condition change in customer is reported , and some problem is arisen in this specification due to the change.z When a new problem is arisen at the customer’s operating set for sample evaluation in the customer site.11 D imensional Outline12. Package DrawingTBD。
ikancorp VK7i 7英寸LCD监视器说明书
CONDITIONS OF WARRANTY SERVICE• Free service for one year from the day of purchase if the problem is caused by manufacturing errors. • The components and maintenance service fee will be charged if the warranty period has expired.Free Service will not be Provided in the Following Situations: (* Even if the product is still within the warranty period.) • Damage caused by abuse or misuse, dismantling, or changes to the product not made by the company. • Damage caused by natural disaster, abnormal voltage, and environmental factors etc.1.713.272.8822********************What’s included☐ 1 x VK7i Monitor ☐ 1 x AC Adapter☐ 1 x Camera Shoe Mount☐ 1 x DV Battery Plate (Check one)DV BATTERY PLATES☐ VK7i-1: Canon 900, Sony L, Panasonic D54 Battery Plates☐ V K7i-2: Canon E6, Nikon EL15, PanasonicG6 Battery PlatesVK7i1281211109131415Power SwitchPower ON / OFFPower Indicator Light When the power is ON, the LED green lights up Button T oggle left in MENU setting modeand ButtonsT oggle up and down in MENU setting mode / MENU ButtonT oggle right in MENU setting modeIn MENU, push button to select menu setting BRIGHT/R KnobAdjust brightness 0 - 100 (50)Adjust red channel CONTRAST/G KnobAdjust contrast 0 - 100 (50)Adjust green channel CHROMA/B KnobAdjust chroma 0 - 100 (50)Adjust blue channelTINT/SHARPNESS KnobAdjust tint 0 - 100 (50)Adjust sharpness 0 - 100 (10)TALL Y Indicator Lights1TALL Y Indicator LightsVIDEO terminal (BNC)IN : Composite signal input terminal OUT : Input signal through-out terminal YPbPr terminal (BNC)IN : Component signal input terminal OUT : : Input signal through-out terminal HDMI terminalIN : HDMI input terminalOUT : : Input signal through-out terminal DC 12V-24V power terminal XLR DC Connection TALL Y Input Connector RJ45 Connection DC 7-24V power terminal Standard DC ConnectionVESA 100mm Mount HolesThreaded for M3x.07 screws. Use to attach pro battery plate adapter or for mounting third party vesa mounts. USB terminalFor factory service use only¼-20 Threaded insert (on three sides of monitor) Mounting MonitorDV Battery Plate SlotMounting ikan DV battery plate234568791110++TALLYThe MANUAL function allows you to change the values of Red, Green, and Blue (RGB).This function recalls user de ned values settings .The user setting will remain in memory inde nitely and can be erased by using the reset option in the main menu.The DSLR Scaling function will allow users to extend their DSLR camera’s HDMI video output any option of four – Normal, 3:2, 16:9 or Full Screen – convenience made simple.This function displays the blanking portion of the incoming signal.The LCD panel in this display has a native display of 1280 x 800 pixels. A signal of any other resolution is scaled to t this native resolution. There may be time when it is desired to view the incoming signal without scaling. Enabling Pixel to Pixel mode turns off the scaling and displays a 1024x600 pixel window of the original image. Each pixel of the panel displays one pixel of the original image. The user may use the arrow buttons(buttons 3-6) on the monitor face to move the window left, right, up and down to see thedesired portion of the image. The VK7i is equipped with Monochrome Peaking features which highlight the desired focus area in a bright, red outline. The operator adjusts the focus control until the red indicator outlines on the desired area are razor sharp, indicating optimal focus. For the best results, be sure the subject is properly exposed.The False Color feature utilizes a full spectrum of assigned color indicators, ensuring awless shot exposure. As the camera Iris is adjusted, the subject of the image will change color based on speci c brightness values indicating optimal exposure. See included chart for color assignments.As an additional tool associated with the VK7i’s False Color feature, ikan’s exclusive Adjustable Under Exposure and Over Exposed Waning feature gives the operator full control of the VK7i False Color brightness values. By setting the preferred IRE exposure limits, the operator is warned when the image exposure is exceeding or falling under the preset IRE limit, providing customizable, full image exposure control.The VK7i offers adjustable upper Clip Guide levels to accurately display overexposed images in any shooting condition. The operator simply assigns the upper IRE to their preference and any exposure over the set IRE limit will ash in a vivid purple, indicatingonly the over exposed area.This function displays a side by side comparison of the incoming video signal. Pushing the F1/2 button one time will enter the mode. Each time the F1/2 button is pushed it will freeze the current frame on the right hand side of the display while the left continues to display the live signal. Pressing the exit button will exit the window mode. Use Window 1 for 16:9 signals and Window 2 for 4:3 signals. Display a crosshair on the center of screen.Brightness 0-100Contrast 0-100Chroma 0-100Sharpness 0-100Tint 0-100Color T emp. 5600 K6500 K9300 K MANUAL OSD Language English Chinese OSD Duration5-60 secondLuma Under Warn Luma Over WarnFuction 1 Window 1Window 2 HV DelayGuidesPeakingFalse Color Clip Guide Underscan DSLR Scaling Check Field Pixel Fuction 2 Window 1 Window 2 HV DelayGuidesPeakingFalse Color Clip Guide UnderscanDSLR Scaling Check Field Pixel Menu SetupUser 1-5System ResetCONFIGURATION OF SETTING MENUSCrosshairCrosshairFEATURES• 1280 x 800 resolution• Looping HDMI, Component, and Composite I/O• False Color - Adjustable Under Luminance & Over Luminance Warning• Clip Guide - Adjustable Threshold• Peaking Red outline• Under scan• Color T emperature Presets (9300K/6500K/5600K)• Guides (4: 3 & 16:9 Framing Safe Area)• Check Field (Blue gun, red, green, mono)• Side-By-Side Freeze Frame• H/V Delay• Aspect Ratio (FULL / 16: 9 / 4: 3)• 5 user-de ned group• RGB Adjust• Resolution support - 480i/p ; 576i/p ; 720p24hz 25hz 30hz 50hz 60hz 24hzsf 25hzsf; 1080i/p 24hz 25hz 30hz 50hz 60hz 24hzsf 25hzsf • T ally system• DSLR scaling• Moveable pixel-to-pixelSPECIFICATIONSScreen Size: Diagonal 7" LCDResolution: 1280 x 800LCD Brightness: 400 NITViewing angles: 170(H) 170 (V)Operating Volts: DC 7 to 24VPower Consumption: 7 WattVideo Inputs: HDMI, Component, CompositeVideo Outputs: HDMI, Component, CompositeDimension: 5.6"H x 7.3"W x 1.6"DWeight: 18 lbs。
友达7寸高亮全视角液晶屏-G070VVN01.1
包含在屏信号接口中
背光电路
无
五、友达7寸工业液晶屏G070VVN01.1信 RGB (1 ch, 6/8-bit)
面板电压
3.3V (Typ.)
面板电流
160/197mA (Typ./Max)
面板功率
528/650mA (Typ./Max)
接口类型
友达7寸高亮全视角液晶屏-G070VVN01.1
一：友达7寸工业液晶屏G070VVN01.1基本信息
品牌
友达（AUO）
面板型号
G070VVN01.1
工作温度
-20 ~70°C
存储温度
-30 ~ 80°C
作业湿度
5-95 (%RH)
保存湿度
5-95 (%RH)
当前生产状态
大量现货
二：友达7寸工业液晶屏G070VVN01.1结构特征
152.4*91.44mm（横*竖）
可视区域
154.2*93.24mm（横*竖）
外观尺寸
164.55*104.71mm（横*竖）
外观尺寸
8.0±0.15 mm (厚度)
触摸屏
无
三：友达7寸工业液晶屏G070VVN01.1光学特征
显示模式
AMVA3，常黑显示，透射式
液晶屏亮度
600cd/m2 (Typ.)
液晶屏尺寸
7英寸
点分辨率
800（RGB）* 480（WVGA）
像素密度
133PPI
像素排列
RGB垂直条状
宽高比
15:9（宽:高）
点间距
0.0635*0.1905mm（横*竖）
像素间距
0.1905*0.1905mm（横*竖）
at070tn92使用手册
AT070TN92使用手册一、产品概述AT070TN92是一款7英寸的触摸屏显示器，具有高分辨率、高亮度、高对比度等特点，适用于各种商业和工业应用。
本手册将详细介绍AT070TN92的使用方法、功能和操作步骤。
二、快速启动指南1.连接电源：将AT070TN92的电源线连接到电源插座，并确保电源线连接牢固。
2.打开显示器：按下AT070TN92的电源按钮，等待显示器启动。
3.关闭显示器：按下AT070TN92的电源按钮，关闭显示器。
三、显示面板说明AT070TN92的显示面板采用高清LED背光，颜色逼真，视角广泛。
显示面板支持多点触控，可实现手势控制和多点操作。
四、按键功能介绍AT070TN92具有多个功能按键，包括电源按钮、音量调节按钮、菜单按钮等。
这些按键的功能如下：1.电源按钮：用于打开和关闭显示器。
2.音量调节按钮：用于调节扬声器的音量大小。
3.菜单按钮：用于进入菜单界面，进行各种设置和调整。
五、菜单操作指导AT070TN92的菜单界面采用图形化设计，用户可以通过触控或键盘进行操作。
菜单包括亮度、对比度、颜色等选项，可根据需要进行调整。
用户可根据实际需求选择相应菜单项，并进行参数设置和调整。
六、常见问题解答Q1：如何解决触摸屏失灵问题？A1：首先检查触摸屏是否清洁，如有污垢请用柔软的布擦拭干净；其次检查触摸屏是否正常工作，如有问题请联系专业维修人员进行检查和维修。
Q2：如何调整显示器的亮度？A2：在菜单界面中，选择“亮度”选项，通过滑动条或输入数值来调整亮度。
根据实际需要选择合适的亮度值，以获得更好的视觉效果。
Q3：触摸屏响应速度较慢或无法正确识别手势。
A3：请检查触摸屏是否清洁，如有污垢请用柔软的布擦拭干净。
如仍无法解决问题，可能是触摸屏出现故障，请联系专业维修人员进行检修。
七、性能参数列表AT070TN92的性能参数如下：1.尺寸：7英寸2.分辨率：800x480像素3.亮度：350cd/m²4.对比度：1500:15.视角：178°/178°（水平/垂直）6.响应时间：5ms7.触摸屏类型：电容式触摸屏8.颜色：16.7M色彩9.工作温度：0℃～40℃10.存储温度：-10℃～50℃11.工作湿度：10%～85%相对湿度（无冷凝）12.存储湿度：5%～95%相对湿度（无冷凝）13.电源要求：DC 12V/3A电源适配器（电池充电器）14.功率消耗：≤35W（正常工作），≤0.5W（待机/关机）八、安全注意事项1.请勿在潮湿的环境中使用AT070TN92，以免造成短路或设备损坏。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
LCD液晶屏： 友达全视角7寸工业液晶屏-G070VVN01.2 工控屏
品牌友达（AUO）
面板型号G070VVN01.2
工作温度-20 ~70°C
存储温度-30 ~ 80°C
作业湿度5-95 (%RH)
保存湿度5-95 (%RH)
当前生产状态量产中
液晶屏尺寸7英寸
点分辨率800（RGB）*480（WXGA）
像素密度133PPI
像素排列RGB垂直条状
宽高比15:9（宽:高）
点间距0.0635*0.1905mm（横*竖）
像素间距0.1905*0.1905mm（横*竖）
液晶屏重量143g（Typ.）
表面处理雾面，Hard Coating（3H）
显示区域152.4*91.44mm（横*竖）
可视区域154.2*93.2mm（横*竖）
外观尺寸164.55*104.71mm（横*竖）
外观尺寸8.5(Max.) mm (厚度)
触摸屏带触摸屏（投射电容屏）
显示模式MVA，常黑显示，透射式
液晶屏亮度600cd/m2 (Typ.)
对比度1500:1 (Typ.) (透射)
显示颜色262K/16.2M (6-bit / 6-bit + FRC)
显示色域70%NTSC(CIE1931)
响应时间10/25(Typ.)(Tr/Td)(ms)
可视角度80/80/80/80 (Typ.)(CR≥10) (左/右/上/下) 最佳视角全视角
白色色度X:0.311; Y:0.328
白场变动 1.25 (Max.)(9 points)
灯管位置侧入式光源
光源类型WLED
灯管数量7S2P
灯管形状阵列
灯管数量 4 strings
光源寿命30K(Min.)（小时）
单灯电压22.4/25.2V（Typ./Max.）
单灯电流120mA(Typ.)
灯管功率总耗 2.69/3.03W (Typ./Max.)
背光电路无
信号大类TTL
信号小类Parallel RGB(1 ch, 6/8-bit)
面板电压 3.3V (Typ.)
面板电流160/197mA (Typ./Max)
面板功率528/650mW(Typ./Max)
接口类型端子
接口脚距 1.25 mm
接口数量 1 pcs
接口脚数20 pins
●补充说明：以上资料仅供参考，如有某项不准确，可以联系我们客服提供产品的规格资料，产品均以pdf规格为准。