科尔摩根伺服报警代码(中文)
科尔摩根伺服报警代码中文
科尔摩根伺服报警代码(中文）————————————————————————————————作者: ————————————————————————————————日期：错误编号名称说明E ／P 状态信息通电状态正常．．. 状态信息放大器是更新启动配置- 状态信息编程模式- S －AＳ-Ｅnaｂｌe AS-Ｅnaｂle输入0VF01* 散热片温度散热片温度过高(默认：８0°C)Ｆ0２* 超压供电过压F03* 跟踪误差位置控制器F04 信息反馈线缆坏、短路、接地Ｆ05* 欠压供电低压F０6 电机温度电机温度过高,或传感器故障F０7 内部电压内部供应电压不行F08* 超速度电机速度过高,位置偏移Ｆ09 电可擦只读存储器自检错误F１0 信号失灵保护信号失灵保护(线缆坏或接触不良)F１1 制动器线缆坏、短路、接地Ｆ１２电机相位电机位置丢失(线缆坏等)F1３* 环境温度环境温度过高Ｆ14 输出级输出功率错误F15 I²t max．I²t超过最大值F1６* 电源ＢTＢ/ＲTO 2或3个阶段没有供电F1７ A / Ｄ转换器模数转换误差,造成极端的电磁干扰F1８重新生成回复电路故障或不正确的设置F19* 直流母线连接直流母线连接故障F20 槽误差槽误差,取决于类型的扩充卡（见ＡSCII命令参考) F21 操纵错误处理扩充卡错误Ｆ22 保留的保留的F23 总线通讯关闭严重的CAN总线通信的错误Ｆ2４警告显示警告故障Ｆ２5 变换误差换码误差Ｆ26 限位开关硬件限制开关移动误差F2７AＳ操作错误——AS-Enａble输入，使已经确定在同一时间Ｆ２8 现场总线错误现场总线错误(见ＡSCＩI命令参考)F29 现场总线错误现场总线通信干扰(见ＡSCII命令参考)F30 紧急暂停暂停,紧急停车F31 保留保留Ｆ3２系统错误系统软件没有反应正确警告信息编号名称说明E/Ｐ状态信息通电状态正常. . . 状态信息放大器是更新启动配置- S－AS-Enａble ＡS-Eｎable输入0V- 状态信息编程模式n０1 I²t I²t临界值超过n02 回复电压达到预设电压n03* S_故障超过预置下的错误限制n０4＊响应监测响应监测（现场总线)已经启动ｎ05 供应阶段供电相丢失n06* ＳＷ限制开关1通过软件限制开关1ｎ０７* SＷ限制开关2通过软件限制开关2ｎ08 运动任务误差a fauｌty motiｏnｔaｓk was ｓtartedn０9 没有参考点no ｒeferenｃe poinｔ(Hoｍe) set at start of motｉon taskn1０* PＳTOP PSTOP限位开关激活n１１* NSTOP NSTＯP限位开关激活ｎ12 电机加载默认值只有EＮDＡT或ＨIPERFACE,差异电机数字保存在该编码器和放大器、电机负载默认值n１3* 扩展卡24 V直流供电为Ｉ／O扩充卡不可以n14 SｉｎCｏｓ反馈SiｎCｏs换向器(激发和运动）没有完成，将被取消当放大器被激活和激发和运震动进行了n15 保留保留n16 总结警告总结了n3１到ｎ17警告n17 现场总线的同步CＡN同步没有登录ｎ１8 multiturn ovｅrflow maｘ.超过电的机转数量n19 motion tａsk rａｍpｓare lｉｍｉｔｅd在运动范围溢出任务数据n20 无效运动任务无效运动任务n21 PLＣ程序错误详情见可编程序控制器(PLC)的代码n22 max. ｍｏtor temperatｕｒreachｅｄthe usｅr can shｕt dｏｗn tｈｅｐroｃeｓsｂeｆore thｅtempｅｒａturｅｅrｏr wｉll ｉnｔeｒruｐt tｈe prｏcesｓimmedｉatel ｙn２３ＳｉnＣoｓ反馈到达警告等级n24 数字I /O配置不合乎逻辑ｎ２５－n３１保留保留ｎ32 固件版本固件版本是一个n故障错误诠释显示意义可能原因措施／解释HMI（人机界面）消息：通信故障电缆使用错误使用nｕll-moｄem电缆伺服放大器或PC上电缆插错位置正确的插伺服放大器和PC电缆插头错误的ＰC接口选择选择正确的界面F０1* 散热片温度散热片温度过高调整系统设置温度（80）或降低环境温度放大器过脏检查／吹出通风槽。
科尔摩根伺服说明书
CD S YNQ N ETQ UICK S TART G UIDERevision No: 7Date: 22 December 20041. General1.1 Safety InformationOnly qualified personnel are permitted to transport, assembly, commission, and maintenance this equipment. Properly qualified personnel are persons who are familiar with the transport, assembly, installation, commissioning and operation of motors, and who have the appropriate qualifications for their jobs. The qualified personnel must know and observe the following standards and regulations:IEC 364 resp. CENELEC HD 384 or DIN VDE 0100 IEC report 664 or DIN VDE 0110National regulations for safety and accident prevention or VBG 4 •Read all available documentation before assembly and commissioning. Incorrect handling of products in this manual can result in injury and damage to persons and machinery. Strictly adhere to the technical information on the installation requirements.• It is vital to ensure that all system components are connected to earth ground. Electrical safety is impossible without a low-resistance earth connection.•The SERVOSTAR® product contains electro-statically sensitive components that can be damaged by incorrect handling. Discharge any electrical shock potential from you before touching the product. Avoid contact with high insulating materials (artificial fabrics, plastic film, etc.). Place the product on a conductive surface.• During operation keep all covers and cabinet doors shut. Otherwise, there are deadly hazards that could possibility cause severe damage to health or the product.• In operation, depending on the degree of enclosure protection, the product can have bare components that are live or have hot surfaces. Control and power cables can carry a high voltage even when the motor is not rotating. • Never pull out or plug in the product while the system is live. There is a danger of electric arcing and danger to persons and contacts.•After powering down the product, wait at least ten minutes before touching live sections of the equipment or undoing connections (e.g., contacts, screwed connections). Capacitors can store dangerous voltages for long periods of time after power has been switched off. To be safe, measure the contact points with a meter before touching.When these symbols are seen in this manual, be alert to the potential for personal injury. Follow the recommended precautions and safe operating practices included with the alert symbols. Safety notices in this manual provide important information. Read and be familiar with these instructions before attempting installation, operation, or maintenance. The purpose of this section is to alert users to possible safety hazards associated with this equipment and the precautions that need to be taken to reduce the risk of personal injury and damage to the equipment. Failure to observe these precautions could result in serious bodily injury,damage to the equipment, or operational difficulty. The safety-alert symbols are:Warning Alerts users to potential physical danger or harm. Failure to follow warning notices could result in personal injury or death.Caution Directs attention to general precautions, which if not followed, could result in personal injuryand/or equipment damage.Note Highlights information critical to your understanding or use of the product.1.2 Limited WarrantyIncludes software provided by KollmorgenSeller warrants that the Goods sold hereunder are free from defects in material and workmanship for the product warranty period of each item of Goods (Product Warranty Periods are listed below). Seller warrants its Good(s) only to the originalpurchaser (the “Customer”), and in the case of original equipment manufacturers or distributors, only to their original consumer (the “Customer”). There are no warranties whatsoever on Goods built or acquired, wholly or partially, to a buyer’s designs or specificationsThis express warranty is in lieu of and exclude all other warranties, express or implied, by operation or law or otherwiseincluding THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (WHETHER KNOWN TO SELLER OR NOT), all other such warranties being hereby expressly disclaimed by Seller and waived by Buyer. Written notice of claimed defects shall have been given to Seller within the period set forth in the schedule below, and within thirty (30) days from the date any such defect is first discovered.广州科沃—工控维修的１２０ ｗｗｗ．ｇｚｋｏｗｏ．ｃｏｍ1.2.1 Product Warranty SchedulesBrand Products Warranty Period Kollmorgen Standard Brush-type Motors,Electronics and Accessories12 months from date of manufactureKollmorgen Standard Brushless Motors, Electronicsand Accessories24 months from date of manufactureKollmorgen Standard Step Motors, Stepper Controlsand Accessories12 months from date of manufactureKollmorgen Custom Motion Systems or componentsof any type To be negotiated on a case-by-case basis, and set forth in the order.Pacific Scientific All Products 24 months from date of manufactureSuperior All Products 12 months from date of manufactureThe Goods or parts claimed to be defective must be returned to Seller, accompanied by a Return Material Authorization (RMA) issued by Seller’s facility responsible for supplying Goods, with transportation prepaid by Customer, with written specifications of the claimed defect.If a warranty claim is valid, Seller shall pay reasonable one-way costs of transportation of the defective Goods from either the original destination or the location where defect occurred, whichever is closest to Seller’s facility. Under no circumstances shall Seller be liable for removal of Seller’s Goods from Buyer’s equipment or re-installation into Buyer's equipment.No person, including any agent, distributor, or representative of Seller, is authorized to make any representation or warranty on behalf of Seller concerning any goods manufactured by Seller, except to refer purchasers to this warranty.1.2.2 GeneralIndemnityBuyer agrees to hold Seller harmless from any and all liability, and to pay all costs and attorney’s fees, for injury or damage to persons or property caused in any manner by Goods covered by the order while in possession or under the control of Buyer or Buyer’s successor in interest.1.2.3 Use As DirectedThe following guidelines describe the restrictions for proper use of the SERVOSTAR CD SynqNet system: • The amplifiers are components built into electrical equipment or machines and can only be commissioned as integral components of such equipment.• The servo amplifiers are to be used only on earthed three-phase industrial mains supply networks (TN-system, TT-system with earthed neutral point).• The servo amplifiers must not be operated on power supply networks without an earth or with an asymmetrical earth.• If the servo amplifiers are used in residential areas, or in business or commercial premises, the user must implement additional filter measures.• The servo amplifiers are only intended to drive specific brushless synchronous servomotors from Kollmorgen with closed-loop control of torque, speed, and position. The rated voltage of the motors must be at least as high as theDC-link voltage of the servo amplifier.• The servo amplifiers may only be operated in a closed switchgear cabinet, taking into account the ambient conditions defined in the environmental specifications.Kollmorgen guarantees the conformance of the servo amplifiers with the standards for industrial areas stated in this manual only if Danaher Motion Kollmorgen delivers the components (motors, cables, amplifiers etc).1.2.4 SoftwareWarrantyComputer software programs that may be included in material or Goods sold to Buyer have been designed to perform a given set of tasks as defined in the documentation provided and are offered AS IS. It is Buyer’s responsibility to determine if the features of the software programs are suitable for Buyer’s requirements and must confirm that the software programs operate correctly. Buyer understands that such software programs are of such complexity that they may have inherent defects and that Seller makes no warranty that all software features will perform correctly as supplied. For Seller’s software utilizing automation servers, improper reading and writing data to the automation server can cause the automation server software to malfunction and may cause the automation server and/or the program writing to the automation server to crash. Improperly reading and writing data to an automation server may cause the device controlled by that automation server to malfunction. Seller shall not be responsible for damage to any device or damage caused by any device due to the improper reading and/or writing of data to an automation server.1.2.5 Limitation of liabilityNOTWITHSTANDING ANYTHING TO THE CONTRARY, SELLER SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING LOST PROFITS ARISING OUT OF THE PERFORMANCE, DELAYED PERFORMANCE OR BREACH OF PERFORMANCE OF THIS ORDER REGARDLESS WHETHER SUCH LIABILITY BE CLAIMED IN CONTRACT, EQUITY, TORT OR OTHERWISE. SELLER’S OBLIGATION ISLIMITED SOLELY TO REPAIRING OR REPLACING (AT ITS OPTION AND AS SET FORTH IN SECTION 10 AND SECTION 11), AT ITS APPROVED REPAIR FACILITY, ANY GOODS OR PARTS WHICH PROVE TO SELLER’S SATISFACTION TO BE DEFECTIVE AS A RESULT OF DEFECTIVE MATERIALS OR WORKMANSHIP, IN ACCORDANCE WITH SELLER’S STATED WARRANTY. IN NO EVENT SHALL SELLER’S LIABILITY EXCEED THE TOTAL PURCHASE PRICE SET FORTH IN THIS ORDER.number1.3 Part1.4 Where to get supportDanaher Motion is committed to quality customer service. Our goal is to provide the customer with information and resources as soon as they are needed. In order to serve in the most effective way, contact your local sales representative for order status and delivery information, product information and literature, and application and field technical assistance. If you are unaware of your local sales representative, please contact us at:Email: sep@Specify “SynqNet Support” in the subject line.1.5 Manual Download LocationComplete product manuals can be downloaded from the Danaher Motion website, at -> Customized Products -> Drives -> CD SynqNet2. Unpacking and InspectionOpen the box and remove all the contents. Check to ensure there is no visible damage to any of the equipment.Electronic components in this amplifier are design-hardened to reduce static sensitivity. However, properprocedures should be used when handling to avoid damage to equipment.Remove all packing material and equipment from the shipping container. Be aware that some connector kits and other equipment pieces may be quite small and can be accidentally discarded if care is notobserved when unpacking the equipment. Do not dispose of shipping materials until the packing list hasbeen checked.Upon receipt of the equipment, inspect components to ensure that no damage has occurred in shipment. If damage is detected, notify the carrier immediately. Check all shipping material for connector kits, documentation, diskettes, CD-ROM, or other small pieces of equipment.3. Installation Instructions3.1 GeneralThese installation steps are designed to lead you through the proper installation and setup of a SERVOSTAR CD SynqNetsystem. They were developed with the assumption that you have a fundamental understanding of basic electronics, computers, mechanics, and proper safety practices. However, you do not have to be an expert in motion control to install and operate thedrive system. It is recommended that you read the entire manual completely before attempting installation or operation.High voltage can present dangerous and hazardous conditions if not performed by a qualified electrician. Be certain to follow all national and local codes during installation.1. Open the box(es) and remove all the contents. Check to ensure there is no visible damage to any of the equipment.2. Mount the SERVOSTAR CD SynqNet to the back panel. Refer to the appropriate Outline Dimensions in this manual. Metal-to-metal contact is important for electrical noise control!3. Wire the SERVOSTAR CD SYNQNET according to the appropriate System Wiring Diagram.4. Connect solid earth ground to frames of all components.5. Wire the main power (115/230 VAC). Wire the 24 volt supply to the connector at the top of the drive.6. Wire user I/O at connector C3: At a minimum, 24 volts must be brought in to the enable circuit. Be certain that connector C3 is inserted correctly.7. Wire the motor and feedback. Refer to the Feedback Wiring Diagram for additional information. 8. Wire Regen Resistor kit, if applicable. 9.Verify that all wiring is correct.10. Verify that earth grounds are connected. 11. Verify all electrical and safety codes are met.12. Connect the SynqNet cable between the Motion Controller and connector C4.3.2 GroundingSystem grounding is essential for proper performance of the drive system. A ground bus bar may be used as a single point ground for the system. Safety grounding should be provided to all pieces of the system from a “star point." In addition to the safety grounding, a high frequency ground must be provided that connects the back panel to the enclosure and, ultimately, to earth ground. The objective is to provide an extremely low impedance path between the filters, drives, power supplies, and earth ground. This high frequency ground is accomplished with the use of a flat braid or copper bus bar. It is important not to rely on a standard wire for the high frequency ground. In general, a wire has an inductance of 8nH-per-inch, regardless of diameter. At higher frequencies, this unwanted inductance between grounds equates to limited filter performance. When connecting high frequency grounds, use the shortest braid possible.3.3 BondingThe proper bonding of shielded cables is imperative for minimizing noise emissions and increasing immunity levels of the drive system. Its effect is to reduce the impedance between the cable shield and the back panel. Kollmorgen recommends that all shielded cables be bonded to the back panel.Power input wiring does not require shielding (screening) if the power is fed to the cabinet (enclosure) via metallized conduit. If metallized conduit is not implemented into the system, shielded cable is required on the power input wires and proper bonding technologies should be implemented.The motor and feedback cables should have the shield exposed as close to the drive as possible. This exposed shield is bonded to the back panel using either non-insulated metallic cable clamps or cable bonding clamps offered by Phoenix Contact (and others).3.4 CEFilteringThe SERVOSTAR drive system (drive, motor) has been designed to meet the CE standards. It is imperative for you to apply proper bonding and grounding techniques, described earlier in this section, when incorporating EMC noise filtering components for the purpose of meeting this standard.Noise currents often occur in two types. The first is conducted emissions that are passed through ground loops. The quality of the system grounding scheme inversely determines the noise amplitudes in the lines. These conducted emissions are of a common-mode nature from line to neutral (or ground). The second is radiated high-frequency emissions usually capacitively coupled from line-to-line and are differential in nature.To properly mount the filters, the enclosure should have an unpainted metallic surface. This allows for more surface area to be in contact with the filter housing and provides a lower impedance path between this housing and the back plane. The back panel, in turn, has a high frequency ground strap connection to the enclosure frame or earth ground.3.4.1 InputPowerThe Kollmorgen SERVOSTAR CD SynqNet electronic system components require EMI filtering in the input power leads to meet the conducted emission requirements for the industrial environment. This filtering blocks conducted-type emissions from exiting onto the power lines and provides a barrier for EMI on the power lines.Care must be taken to adequately size the system. The type of filter is based on the voltage and current rating of the system and whether the incoming line is single or three-phase. One input line filter is used for multi-axis control applications. These filters are mounted as close to the incoming power as possible so noise is not capacitively coupled into other signal leads and cables. Similarly, care should be taken when routing wires from the load side of the filter to the BUS Module. These lines may be noisy and should be separated from other sensitive cabling to avoid unwanted coupling of noise. Several manufacturers of these filters are listed below. They should be able to recommend the best filter design for most typical motor control applications. Kollmorgen has also provided specific filters recommendations that adequately attenuate the conducted noise to levels well below the CE limits. The implementation of the EMI filter should be done in accordance with the following guidelines: • Filter should be mounted on the same panel as the drive.• Filter should be mounted as close as possible to incoming cabinet power.• When mounting the filter to the panel, remove any paint or material covering. Use an unpainted metallic back panel, if possible.• Filters are provided with an earth connection. All ground connections are tied to ground.• Filters can produce high leakage currents. Filters must be earthed before connecting the supply!• Filters should not be touched for a period of 10 seconds after removing the supply.The following table shows recommended line filters:Drive Model # Recommended EMI Line FilterKollmorgen Part #Lx03 Filter Concepts SF7Schaffner FN258-7/07 n/aA-96776-001Lx06 Filter Concepts SF15Schaffner FN258-16/07 N/aA-96776-002Lx10 SchaffnerFN258-16/07A-96776-002 Lx20The filters called out in the table on the previous page are used on a one-to-one corresponedence withthe drive. If drives are paralled off one filter, it needs to be sized.Drives can be ganged off one EMI filter as shown in the Filter and Bonding Diagrams.3.4.2 Motor Line FilteringMotor filtering may not be necessary for CE compliance of SERVOSTAR systems. However, this additional filtering increasesthe reliability of the system. Poor non-metallic enclosure surfaces and lengthy, unbonded (or unshielded) motor cables thatcouple noise line-to-line (differential) are just some of the factors that lead to the necessity of motor lead filtering.Motor lead noise may be either common-mode or differential. The common-mode conducted currents occur between eachmotor lead and ground (line-to-neutral). Differential radiated currents exist from one motor lead to another (line-to-line). Thefiltering of the lines feeding the motor provide additional attenuation of noise currents that enter surrounding cables andequipment I/O ports in close proximity.Differential mode currents commonly occur with lengthy motor cables. As the cable length increases, so does its capacitanceand its ability to couple noise from line-to-line. While every final system is different and every application of the product causesa slightly different emission profile, it may become necessary to use differential mode chokes to provide additional noiseattenuation to minimize the radiated emissions. The use of a ferrite core (placed at the drive end) on each motor lead (shown inthe diagram below), attenuates differential mode noise and lower frequency (30-60 MHz) broadband emissions to withinspecifications. Kollmorgen recommends a Fair-Rite P/N 2643665702 (or equivalent) ferrite core. You should wrap each motorlead through the core several times, as shown in the next figure.Never wrap a ground lead through a core.To MotorCommon ModeFilteringDifferential Mode FilteringCommon mode currents occur from noise spikes created by the PWM switching frequency of the drive. The use of a ferrite or iron-powder core toroid, as shown in the figure above, places common mode impedance in the line between the motor and the drive. The use of a common mode choke on the motor leads may increase signal integrity of encoder outputs and associated I/O signals. The following is a list of toroidal and ferrite cores used to make common mode chokes:3.4.3 I/O FilteringI/O filtering, while not a necessity for CE compliance, may be desired (depending on system installation, application, andintegration with other equipment). It may be necessary to place ferrite cores on I/O lines to avoid unwanted signals entering and disturbing the drive system or other associated equipment. The following chart lists some ferrite parts that may be used for I/O filtering and noise attenuation. These parts are ideal for providing an in-line common mode impedance for I/O linesThe following figure illustrates the use of multiple turns through a clamp-on core. The more turns created, the more impedance is added to the line. Avoid putting the shield in a clamp-on core. It is undesirable to place an impedance inline with the shield. The use of ribbon cable may be common in many cabinets. Some ferrite clamps are designed just for ribbon cable use.4. WiringDiagram4.1 Wiring4.1.1 300V Model: 3A, 6A, 10AY4.1.2600V Model and 20A 300V ModelH I G H V O L T A G E M A Y E X I S T U P T O 5 M I N U T E SA F T E R I N P U T V O L T A G E I S R E M O V E D .Y R E F E R I N S T A L L A T I O N A N D T R O U B L E S H O O T I N GT O Q U A L I F I E D P E R S O N N E L O N L Y .(S4.2 ConnectorPin-Out4.2.1 C1:RS232Pin no Function Description Comments1 N.C.2 RxD Receive3 TxD Transmit4 N.C.5 DGND Ground Must be connected in order to equalizepotential between controller and drive.6 N.C.7 N.C.8 N.C.9 N.C.4.2.2 C2:FeedbackPin Resolver Encoder SineEncoder1 SineHigh A A2 SineLow /A /A3 Shield Shield Shield4 CosineHigh B B5 CosineLow /B /B6 Shield Shield Shield7 E5V Return E5V Return8 E5V Return E5V Return9 H1B EnDat/Data10 H2B EnDat/Clock11 H3B12 Shield Shield Shield13 Thermostat High Thermostat High Thermostat High14 Shield Shield Shield15 Ref. High Out Index Index16 Ref. Low Out /Index /Index17 Shield Shield Shield18 E5V Supply E5V Supply19 E5V Supply E5V Supply20 E5V Supply E5V Supply21 Shield Shield Shield22 H1A EnDatData23 H2A EnDatClock24 H3A25 Thermostat Low Thermostat Low Thermostat Low4.2.3 C3: Front-Panel I/OPin no Function Description Comments1 Shield Shield2 Analogin+3 Analogin-Differential analog input ±10Vdc4 AGND Analogground5 Fault relay Fault relay dry contact6 Fault relay Fault relay dry contact 1 AmpNo polarity7 CREF Common rail for Digital inputsand outputs8 Enable RemoteEnable Wired to DSP, sampled at 62.5µsec 9 CW Positivelimit 5-24V; Wired to SynqNet FPGA 10 CCW Negativelimit 5-24V; Wired to SynqNet FPGA 11 HOME Homeinput 5-24V; Wired to SynqNet FPGA12 Brake+ Brake relay positive terminal13 Brake- Brake relay negative terminal Dry-contact for brake control 1 Amp4.2.4 C4: SynqNet INPin no RJ45 In1 TD2+2 TVDD3 TD2-4 RD2+5 TVDD6 RD2-7 NC8 DGND4.2.5 C5: SynqNet OUTPin no RJ45 Out1 TD1+2 TVDD3 TD1-4 RD1+5 TVDD6 RD1-7 NC8 DGND4.2.6 ExtendedI/OPin no Function Description Comments1 Analogin+14 Analogin-Differential analog input ±10Vdc2 AGND Analogground15 IN4 Digital Input #4 5V – 24V, Bi- polarWired to SynqNet FPGA3 IN5 Digital Input #5 5V – 24V, Bi-polarWired to SynqNet FPGA16 IN6 Digital Input #6 5V – 24V, Bi- polarWired to SynqNet FPGA4 IN7 Digital Input #7 5V – 24V, Bi- polarWired to SynqNet FPGA17 Common IN4 to IN7 Common IN4 to IN7 Common for Inputs 4 to 75 IN8 Digital Input #8 5V – 24V, Bi- polarWired to SynqNet FPGA18 IN9 Digital Input #9 5V – 24V, Bi- polarWired to SynqNet FPGA6 IN10 Digital Input #10 5V – 24V, Bi- polarWired to SynqNet FPGA19 IN11 Digital Input #11 5V – 24V, Bi- polarWired to SynqNet FPGA7 Common IN8 to IN11 Common IN8 to IN11 Common for Inputs 8 to 1120 OUT2 Digital output #2 Open collectorWired to SynqNet FPGA8 OUT3 Digital output #3 Open collectorWired to SynqNet FPGA21 Out common 2 to 3 Out common 2 to 3 Common user ground for OUT2 and OUT39 OUT4 Digital output #4 Open collectorWired to SynqNet FPGA22 OUT5 Digital output #5 Open collectorWired to SynqNet FPGA10 Out common 4 to 5 Out common 4 to 5 Common user ground for OUT4 and OUT523 Diff_IO_1+ Differential RS422 I/O (high) 11 Diff_IO_1- Differential RS422 I/O (low) Direction (In or Out) programmable through SynqNet .24 Diff_IO_2+ Differential RS422 I/O (high) 12 Diff_IO_2- Differential RS422 I/O (low) Direction (In or Out) programmable through SynqNet .25 DIV_BY_N Fast output, used for Divide-by-Nsignal Open collector, with internal pull-up that may be dis-assembled.13 DGND Digital Ground The DGND is the common for the outputcollector of this output. The input stage DGNDat the user end has to be connected to thisDGND.4.2.7 C8: Secondary EncoderPin Function 1 A Input + (High) 2 A Input - (Low)3 DC Common4 B Input + (High)5 B Input - (Low)6 Shield Connection7 E5V Supply8 Index +9 Index -4.3Filtering and Bonding DiagramNote 5Bonding of motor cables. The use of armored (screened) motorcables bonded as close to the drive as possible are essential for CE compliance and stronglyrecommended to better the overall performance and reliability of the system.Note 6for CE compliance. As with the motor cables, the feedback cables should be bonded to the back panel. This bonding does twothings. First, it cuts down radiation from the drive, which may be in the form of high frequency energy resulting from internal processor clocks. Second, it providesimmunity for the drive. Since the feedback device is located internal to the motor, it is going to pick up some noise currents and transmit bonding directs the currents from the shield of the feedback cable to back panel ground. This reduces the amount of noise entering the drive.Note 7AC power lines that must be routed past other lines (such as motor cables or I/O lines) should cross at a 90º angle. This minimizes the coupling effect. Additionally, the power lines should be routed as close to the back panel aspossible. Any noise currents on the lines are capacitively coupled to the ground plane and not to other lines.Note 8Control (I/O) signals should be kept separate from all power and motor cables, if possible. Keep control wiring as short as possible and use screened wire. Bonding is also recommended but not required for CE compliance. A separation distance of 20 cm. (8 in.) is sufficient in most cases. Where control cables must cross power cables, they should cross at a 90ºangle.Note 9Motor cables and feedback cables exiting the cabinet going to the motor should be separated as much as possible. Ideally, the use of separate conduits provides good isolation, which can limit coupling of noise from motor to feedback cables.Note 1Input power enters enclosure from metal conduit. Thiseliminates the need for shielded input power cable.Note 2Single point ground. A bus bar (ground bus) is an excellent way to achieve this.Note 3High frequency ground between non-conductive back panel and enclosure. Also, a high frequency ground is required between the enclosure and earth ground.Note 4EMI filter grounding. Safetygrounds must be provided on the filters. Hazard potentials exist even when the power is off because of the capacitors internal to the filters.。
伺服电控报错代码
有故障代码Fault Code无故障代码No Fault Code无剪线No shearing-line.踩下脚踏板电机无任何反应No respond in motor when tread the pedals.电机转动时有异响There is abnormal sound when the motor works.脚踏板无高速Motor don’t accelerate when tread the pedals.显示屏无显示There is no display on the display.操作面板按键无反应No respond on buttons of the operation panel.开机无电无显示No power and no display when power on.开机机器自跑Motor works automatically when power on.没有自动倒缝NO automatic backstitch.“P”+“✄”进入检测模式，调整为P01，查看其数值是否在“250～380V”范围内Please press “P”+“✄”to enter the testing mode, switch to P01,then check whether the value is in the range of “250～380V”.请在关机状态下拔掉电机与伺服器的连接线，转动电机手轮，查看电机轮是否过重Please pull out the connecting line between motor and servo in the off state, then rotate the motor’s hand wheel to see whether the motor’s hand wheel is too heavy.您的电机已短路，请立即更换There are short circuits in your motor, please replace it immediately.您的电网不稳定造成伺服器无法正常工作。
伺服异常码
0（正常狀態）1硬件故障。
2硬件故障。
101運行期間PLC READY OFF 102驅動裝置READY OFF103運行期間測試模式故障104硬件行程極限（+）105硬件行程極限（–）106起動時停止信號ON107BUSY 期間READY OFF-> ON 201在OP 處起動203近點狗檢測時間故障204OP 檢測時間故障205停頓時間故障206計數方法位移量故障207OPR請求ON209OPR 重新起動不可能213ABS 傳送時間214ABS 傳送SUM300JOG 速度範圍之外301微動位移量出錯500非法條件數據編號501同時起動前出錯502非法數據編號503無命令速度504在線性位移量範圍之外506弧出錯大偏差507軟件行程極限+508軟件行程極限–514新的當前值範圍之外515新的當前值不可能516連續路徑控制不可能518在運行形式範圍之外519在插補軸BUSY時插補520單位組不相配521非法插補說明命令522命令速度設置出錯523插補模式出錯524控制系統設置出錯525分點設置出錯526終點設置出錯527圓心設置出錯530地址範圍之外532不能同時起動533條件數據出錯534特殊起動指令出錯535不能環形插補536M代碼ON 信號起動537PLC READY OFF起動538READY OFF 起動543起動點範圍之外544半徑範圍之外545控制系統 LOOP設置出錯546非法設置以度為單位的ABS 方向800保持出錯801閃存ROM 寫出錯802閃存ROM 和校驗出錯803I/O 復位804專用指令參數出錯805閃存ROM 寫次數出錯806專用指令I/F 出錯900在單位設置範圍之外901在每轉的脈衝數範圍之外902在每轉的位移量範圍之外903在單位放大倍率範圍之外904脈衝輸出模式出錯905旋轉方向設置出錯906在偏置速度範圍之外910在速度極限值範圍之外911在加速時間0 範圍之外912在減速時間0 範圍之外920反向間隙補償量出錯921軟件行程極限上限922軟件行程極限下限923軟件行程極限選擇924軟件行程極限有效/無效設置925命令到位寬度926非法轉矩極限設置值927M代碼ON 計時出錯928速度轉換模式出錯929插補速度指定方法930當前值更新請求出錯932手動脈衝發生器輸入模式出錯935速度-位置功能選擇出錯950加速時間1 設置出錯951加速時間2 設置出錯952加速時間3 設置出錯953減速時間1 設置出錯954減速時間2 設置出錯955減速時間3 設置出錯956JOG 速度极限值出错957JOG 加速時間選擇設置出錯958JOG 減速時間選擇設置出錯959加速/減速處理選擇設置出錯960S-形比率設置出錯961非法突然停止減速時間962停止組1 突然停止選擇出錯963停止組2 突然停止選擇出錯964停止組3 突然停止選擇出錯966在容許環形插補出錯寬度之外967外部命令功能選擇出錯980OPR 方法出錯981OPR 方向出錯982OP 地址設置出錯983OPR 速度出错984蠕動速度出錯985OPR 重試出錯990OPR 停頓時間出錯991近點狗ON 後的位移量設置出錯992OPR 加速時間選擇出錯993OPR 減速時間選擇出錯995OPR 轉矩極限值出錯996偏差計數器清零信號輸出時間設置出錯997OP 移動期間速度指定出錯。
伺服报警故障代码大全
伺服报警故障代码大全伺服系统是现代工业自动化生产中常见的一种控制系统，它通过对电机进行控制，实现对机械运动的精确控制。
然而，在使用伺服系统的过程中，我们有时会遇到各种报警故障代码，这些代码代表着不同的故障类型，需要我们及时排查和处理。
下面将为大家详细介绍一些常见的伺服报警故障代码，以便大家在实际工作中能够更好地应对这些问题。
1. E001，伺服系统过载报警。
当伺服系统负载过大时，会触发E001报警代码。
这时需要检查负载情况，可能需要重新调整负载参数或者更换合适的伺服系统。
2. E002，伺服系统过热报警。
当伺服系统工作时间过长或者环境温度过高时，会触发E002报警代码。
此时需要及时停机降温，或者加强散热措施，以确保伺服系统的正常工作。
3. E003，伺服系统电压过高或过低报警。
电压异常会导致伺服系统工作异常，触发E003报警代码。
这时需要检查电源电压情况，可能需要更换稳压器或者调整电源线路。
4. E004，伺服系统编码器故障报警。
编码器是伺服系统的重要传感器，一旦出现故障会触发E004报警代码。
此时需要检查编码器连接情况，可能需要更换或者维修编码器。
5. E005，伺服系统通信故障报警。
通信故障会导致伺服系统无法正常接收指令，触发E005报警代码。
这时需要检查通信线路和通信模块，可能需要重新连接或者更换通信设备。
6. E006，伺服系统电机故障报警。
电机是伺服系统的核心部件，一旦出现故障会触发E006报警代码。
此时需要检查电机连接情况和电机状态，可能需要更换或者维修电机。
7. E007，伺服系统位置偏差报警。
位置偏差会导致伺服系统无法精确定位，触发E007报警代码。
这时需要检查位置传感器和位置控制参数，可能需要重新校准或者调整位置控制系统。
以上是一些常见的伺服报警故障代码，我们在使用伺服系统时，要时刻关注系统的运行状态，及时处理各种报警故障，以确保系统的正常运行。
希望以上内容能够帮助大家更好地理解和应对伺服系统报警故障，提高工作效率和生产质量。
伺服报警[1-2]
![伺服报警[1-2]](https://img.taocdn.com/s3/m/30614eea551810a6f524866a.png)
444
3)p系列SVU．内部风扇故障。
445
n—轴：INV．冷却风扇故障
SVM：内部风扇故障。
446
n—轴：软断线报警
数字伺服软件检测到脉冲编
码器断线。
447
n—轴：硬断线报警
硬件检测到内装脉冲编码器
断线。
n轴硬断线(外部)
600
n—轴：INV．DC
1)SVM：DCLINK电流过大。
LINK过电流
2)p系列SVU：DCLINK电流过
大。
601
n轴 INV．辐
1)SVM：排热风扇故障。
射风扇故障
2)p系列SVU：排热风扇故障。
602
n轴 ：INV．过
SVM：伺服放大器过热。
执
603
2)PSMR-DCLINK电压过高。
CNV．过电压DCLINK
3)a系列SVU．DCLINK电压过
高。
4) p系列SVU．DCLINK电压
过高。
440
n?轴：CNV．EX
1)PSM：再生放电量过大。
441
DECELERATIONPOW．
2)o系列SVU：再生放电量
卡。
● 在FlashMemory中没有安
装正确的伺服软件。
404
伺服报警：
尽管n?轴(1—4)READY信号
(MCON)断开，伺服放大器
READY信号
(DRDY)仍为1。或当电源打
开时，即使MCON断开，DRDY
仍接通。
n?轴VRDYON
检查伺服接口模块和伺服放
科尔摩根伺服报警代码中文
科尔摩根伺服报警代码中文科尔摩根伺服报警代码(中文）————————————————————————————————作者: ————————————————————————————————日期：错误编号名称说明E ／P 状态信息通电状态正常．．. 状态信息放大器是更新启动配置- 状态信息编程模式- S －AＳ-Ｅnaｂｌe AS-Ｅnaｂle输入0VF01* 散热片温度散热片温度过高(默认：８0°C)Ｆ0２* 超压供电过压F03* 跟踪误差位置控制器F04 信息反馈线缆坏、短路、接地Ｆ05* 欠压供电低压F０6 电机温度电机温度过高,或传感器故障F０7 内部电压内部供应电压不行F08* 超速度电机速度过高,位置偏移Ｆ09 电可擦只读存储器自检错误F１0 信号失灵保护信号失灵保护(线缆坏或接触不良)F１1 制动器线缆坏、短路、接地Ｆ１２电机相位电机位置丢失(线缆坏等)F1３* 环境温度环境温度过高Ｆ14 输出级输出功率错误F15 I2t max．I2t超过最大值F1６* 电源ＢTＢ/ＲTO 2或3个阶段没有供电F1７ A / Ｄ转换器模数转换误差,造成极端的电磁干扰F1８重新生成回复电路故障或不正确的设置F19* 直流母线连接直流母线连接故障F20 槽误差槽误差,取决于类型的扩充卡（见ＡSCII命令参考) F21 操纵错误处理扩充卡错误Ｆ22 保留的保留的F23 总线通讯关闭严重的CAN总线通信的错误Ｆ2４警告显示警告故障Ｆ２5 变换误差换码误差Ｆ26 限位开关硬件限制开关移动误差F2７AＳ操作错误——AS-Enａble输入，使已经确定在同一时间Ｆ２8 现场总线错误现场总线错误(见ＡSCＩI命令参考)F29 现场总线错误现场总线通信干扰(见ＡSCII命令参考)F30 紧急暂停暂停,紧急停车F31 保留保留Ｆ3２系统错误系统软件没有反应正确警告信息编号名称说明E/Ｐ状态信息通电状态正常. . . 状态信息放大器是更新启动配置- S－AS-Enａble ＡS-Eｎable输入0V- 状态信息编程模式n０1 I2t I2t临界值超过n02 回复电压达到预设电压n03* S_故障超过预置下的错误限制n０4＊响应监测响应监测（现场总线)已经启动ｎ05 供应阶段供电相丢失n06* ＳＷ限制开关1通过软件限制开关1ｎ０７* SＷ限制开关2通过软件限制开关2ｎ08 运动任务误差a fauｌty motiｏnｔaｓk was ｓtartedn０9 没有参考点no ｒeferenｃe poinｔ(Hoｍe) set at start of motｉon taskn1０* PＳTOP PSTOP限位开关激活n１１* NSTOP NSTＯP限位开关激活ｎ12 电机加载默认值只有EＮDＡT或ＨIPERFACE,差异电机数字保存在该编码器和放大器、电机负载默认值n１3* 扩展卡24 V直流供电为Ｉ／O扩充卡不可以n14 SｉｎCｏｓ反馈SiｎCｏs换向器(激发和运动）没有完成，将被取消当放大器被激活和激发和运震动进行了n15 保留保留n16 总结警告总结了n3１到ｎ17警告n17 现场总线的同步CＡN同步没有登录ｎ１8 multiturn ovｅrflow maｘ.超过电的机转数量n19 motion tａsk rａｍpｓare lｉｍｉｔｅd在运动范围溢出任务数据n20 无效运动任务无效运动任务n21 PLＣ程序错误详情见可编程序控制器(PLC)的代码n22 max. ｍｏtor temperatｕｒreachｅｄthe usｅr can shｕt dｏｗn tｈｅｐroｃeｓsｂe ｆore thｅtempｅｒａturｅｅrｏr wｉll ｉnｔeｒruｐt tｈe prｏces ｓimmedｉatel ｙn２３ＳｉnＣoｓ反馈到达警告等级n24 数字I /O配置不合乎逻辑ｎ２５－n３１保留保留ｎ32 固件版本固件版本是一个n故障错误诠释显示意义可能原因措施／解释HMI（人机界面）消息：通信故障电缆使用错误使用nｕll-moｄem电缆伺服放大器或PC上电缆插错位置正确的插伺服放大器和PC电缆插头错误的ＰC接口选择选择正确的界面F０1* 散热片温度散热片温度过高调整系统设置温度（80）或降低环境温度放大器过脏检查／吹出通风槽。
科尔摩根伺服报警代码(中文)
保留
保留
n16
总结警告
总结了n31到n17警告
n17
现场总线的同步
CAN同步没有登录
n18
multiturn overflow
max.超过电的机转数量
n19
motion task ramps are limited
在运动范围溢出任务数据
n20
无效运动任务
无效运动任务
n21
PLC程序错误
详情见可编程序控制器(PLC)的代码
F30
紧急暂停
暂停，紧急停车
F31
保留
保留
F32
系统错误
系统软件没有反应正确
警告信息
编号
名称
说明
E / P
状态信息
通电状态正常
. . .
状态信息
放大器是更新启动配置
- S -
AS-Enable
AS-Enable输入0V
-
状态信息
编程模式
n01
I²t
I²t临界值超过
n02
回复电压
达到预设电压
n03*
S_故障
检查接触器
I安装电机接触器具有燔接触。
检查接触器
硬件故障
伺服放大器制造商进行维修
电机连接器或马达伺服放大器没有开机
检测插座
F13*
环境温度7)
到伺服放大器制造商进行维修
截止阈值过低
IncreaseTEMPE
开关柜太热了
使用一个冷却装置
F14
输出级
温度传感器故障
测量传感器电阻。
开关:
低温:开关关闭
高温:开关打开。
PTC热敏电阻器:
伺服报警故障代码大全
伺服报警故障代码大全伺服系统在工业自动化领域中扮演着非常重要的角色，它能够提供精准的位置控制和运动控制，从而实现自动化生产线的高效运行。
然而，在使用伺服系统的过程中，难免会遇到各种故障问题，其中报警故障代码是比较常见的一种。
本文将为大家详细介绍伺服系统常见的报警故障代码，以便大家在实际应用中能够快速准确地进行故障排除。
1. E001，过载报警。
当伺服系统承受超出其额定负载能力的负载时，会产生过载报警。
这可能是由于负载过大或者机械传动系统出现故障导致的。
在遇到这种情况时，需要及时停机检查，排除故障后重新启动。
2. E002，过压报警。
过压报警通常是由于电源系统出现问题，导致伺服系统输入电压超出规定范围而产生的。
解决方法是检查电源系统，确保输入电压稳定在规定范围内，必要时更换电源设备。
3. E003，过热报警。
伺服系统在长时间高负载运行或者环境温度过高的情况下，可能会出现过热报警。
这时需要停机降温，同时检查散热系统是否正常运行，确保散热效果良好。
4. E004，编码器故障。
编码器是伺服系统中非常重要的部件，它负责反馈电机的位置信息。
当编码器出现故障时，会导致伺服系统无法准确控制电机位置，从而产生E004报警。
解决方法是检查编码器连接是否良好，必要时更换故障编码器。
5. E005，通信故障。
伺服系统与上位机或者其他设备之间的通信出现故障时，会产生E005报警。
这时需要检查通信线路是否正常，确认通信协议设置是否正确，保证通信畅通。
6. E006，电机故障。
电机本身出现故障也会导致伺服系统报警，通常是由于电机绕组短路或者接线不良导致的。
解决方法是检查电机绕组和接线，必要时更换故障电机。
7. E007，系统故障。
除了以上列举的几种常见故障外，伺服系统还可能因为其他原因产生系统故障报警。
这时需要通过系统故障代码手册或者厂家技术支持进行详细排查，找出故障原因并进行修复。
总结，伺服系统报警故障代码的出现意味着系统出现了异常情况，需要及时处理以避免对生产造成影响。
伺服驱动器故障代码
SERCOS通讯灯下面图示：在伺服驱动上，SERCOS通讯卡上面三个SERCOS通讯灯的位置。
Rec_T 和Tra_T 灯分别亮成绿色，表示接收和传送。
当SERCOS通讯出现错误，错误灯Error亮起红色。
警告代码名称警告内容n01I²t警告电流极限“I²t 信息”参数设置过大n02制动功率功率极限“最大制动功率”参数设置过大n03跟踪误差跟踪错误极限“跟踪错误”参数设置过大n04监控响应监控应答（fieldbus ）被激活n05主相位主相位丢失“缺少主相位”参数是在单相运转下不能工作n06极限开关1通过软件极限开关1n07极限开关2通过软件极限开关22007.1.29伺服驱动器说明n08伺服任务错误一个错误的伺服任务启动n09无“HOME”参考点伺服程序在没有设置“HOME”参照点的情况下启动n10正极限正极限开关激活n11负极限负极限开关激活n12默认值只对于“HIPERFACE ”电机默认值被装载n13SERCOS接口SERCOS接口没正确连接n14HIPERFACE参考模式当HIPERFACE参考模式激活时尝试复位n15表格错误速度电流表格“INXMODE 35”错误n16...n31保留保留n32硬件测试版本硬件不是一个公开的测试版本A复位数字输入X 的“DIGITAL IN x”复位被激活警告代码错误内容发生原因及纠正错误F01驱动器热接收器过热1.改善通风2.减少motion工作循环F02直流电压超极限1.检查参数“主电源电压”的电流设定2.电源电压太高，使用调压器3.制动功率极限超范围，调整伺服或安装大制动电阻器F03跟踪错误超过极限1.增加Irms或 Ipeak峰值(保持在电机使用范围内)2.SW 斜坡参数设置太大F04反馈信号错误或不正确1.反馈装置有缺陷2.检查“反馈类型”参3.检查反馈线缆和连接F05直流电压比工厂预设值（100V)低F06电机过热1.Irms 或Ipeak 设置2.电机缺陷3.如果电机不热，检查反馈电缆和连接4.减小伺服工作循环5改善电机通风F07内部24V故障退还厂家F08电机速度超过极限1.没正确设置反馈参数2.反馈线不正确3.电机相位接反4.检查“Overspeed”过速度参数正确设置F09只读存储器校验错误退回厂家F10闪存检查错误退回厂家F11电机制动故障1.当制动不存在，制动参数设置为“WITH”2.抱闸有缺陷3.检查电机电源线和接线F12电机相位错误1.电机有缺陷2.检查电机电源线和接线F13驱动器内部温度超级限1.改善通风2.减少伺服工作循环F14驱动器输出使用故障1.检查电机线缆是否损坏或短接2.输出模块过热，改善通风3.内部制动电阻器电路短路或故障当驱动器使能时，没有电或电压太低。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
电机温度
电机温度过高，或传感器故障
F07
内部电压
内部供应电压不行
F08*
超速度
电机速度过高，位置偏移
F09
电可擦只读存储器
自检错误
F10
信号失灵保护
信号失灵保护(线缆坏或接触不良)
F11
制动器
线缆坏、短路、接地
F12
电机相位
电机位置丢失(线缆坏等)
F13*
环境温度
环境温度过高
F14
输出级
输出功率错误
坡道在位置控制器、速度控制器超过坡道
在速度控制器降低加速斜坡(ACC)和制动斜坡(DEC)
放大设定得太低。轴不够力,
调整放大。速度环和位置环
放大定的太高了。轴振荡.
调整放大。速度环和位置环可能,屏幕页面,插入一个过滤器
IPEAK(最大电流)太低了
扩大了下面的错误窗口(屏幕上的位置数据页)或使用一个更大的放大器/电机,增加IPEAK
错误
编号
名称
说明
E / P
状态信息
通电状态正常
. . .
状态信息
放大器是更新启动配置
-
状态信息
编程模式
- S -
AS-Enable
AS-Enable输入0V
F01*
散热片温度
散热片温度过高(默认:80°C)
F02*
超压
供电过压
F03*
跟踪误差
位置控制器
F04
信息反馈
线缆坏、短路、接地
F05*
欠压
供电低压
过于陡峭的斜坡
延长加速/制动坡道(ACC,DEC)
间隔太短
恢复之间的间隔延长运动任务(运动任务屏幕页)
振动在当前控制器
调整放大的MLGQ和KTN重置时间
电机有一个inter-turn故障(只有在案例部分短路)
更换电机
F16
电线BTB - 1、2或3阶段的输入供给丢失
三相操作设置在单相in-feed的情况下
电机接触器不打开的时间
检查开关序列
电机接触器具有燔接触.
更换电机接触器
在电路短路对外制动电阻
检查,整顿短路
F15
I²t超过最大值
驱动机械紧
检查机械系统,使用一个更大的放大器/电机
正弦²坡道
扩展加速、刹车坡道((ACC,DEC)
不正确的设计
联系客户支持
不正确的相位角反馈和磁铁电机中的元素。
纠正MPHASE,可能重置为零.
硬件故障
到工厂对伺服放大器维修
F18
回复电路
回复电阻extern选择的,但是内部适用。
检查在屏幕上设置页面基本设置
摧毁回复晶体管
到工厂对伺服放大器维修
F19*
直流总线链接
(可以关掉电源运行两个阶段)
这里没有电压在电力终端.
检查和开关电源
电压等级正确配置。
适应VBUSMIN
过度负荷的直流环节加速时结合软电压源(隔离变压器)
插件卡不允许
联系客户支持
F22
保留
保留
F23
控制器区域网路
严重的CAN总线通信错误.
检查能够电缆和控制器
F15
I²t max.
I²t超过最大值
F16*
电源BTB/RTO
2或3个阶段没有供电
F17
A / D转换器
模数转换误差,造成极端的电磁干扰
F18
重新生成
回复电路故障或不正确的设置
F19*
直流母线连接
直流母线连接故障
F20
槽误差
槽误差,取决于类型的扩充卡(见ASCII命令参考)
F21
操纵错误
处理扩充卡错误
F30
紧急暂停
暂停，紧急停车
F31
保留
保留
F32
系统错误
系统软件没有反应正确
警告信息
编号
名称
说明
E / P
状态信息
通电状态正常
. . .
状态信息
放大器是更新启动配置
- S -
AS-Enable
AS-Enable输入0V
-
状态信息
编程模式
n01
I²t
I²t临界值超过
n02
回复电压
达到预设电压
n03*
S_故障
紧急停止已经切断电源电压
操作员信息
VBUSMIN参数集太低了
调整参数,例如在48 v直流应用.
The monitor has to be switched off in some applications withUVLTMODE
例如:定位轴的水管的事件失败.
F06
电机温度
电机过热
不正确的运动参数和冷却
硬件故障
到伺服放大器制造商进行维修
反馈系统与过量的功率现状。
ContactCustomer Support
F08*
超速行驶
速度超过允许的极限
检查VOSPD(极限速度)和提高它,如果必要的。
速度超过允许的极限
减少overswing通过指定放大参数
反馈电缆缺陷
(可能是检查在电缆)代替电缆
VLIM太低
当一个新的电动机负载,更快的电动机和最大。只有3000转/分钟也进入了。最后速度和超速有被改编为更高的速度。
F22
保留的
保留的
F23
总线通讯关闭
严重的CAN总线通信的错误
F24
警告
显示警告故障
F25
变换误差
换码误差
F26
限位开关
硬件限制开关移动误差
F27
AS
操作错误——AS-Enable输入,使已经确定在同一时间
F28
现场总线错误
现场总线错误(见ASCII命令参考)
F29
现场总线错误
现场总线通信干扰(见ASCII命令参考)
超过预置下的错误限制
n04*
响应监测
响应监测(现场总线)已经启动
n05
供应阶段
供电相丢失
n06*
SW限制开关1
通过软件限制开关1
n07*
SW限制开关2
通过软件限制开关2
n08
运动任务误差
a faulty motion task was started
n09
没有参考点
no reference point (Home) set at start of motion task
F02*
在直流母线过电压的链接
设置电源电压
反馈电压过高
“n02“预先显示。可能使用外部制动电阻,或者在多个放大器,连直流环节。
电压设定太低
基本设置屏幕页面设置正确的电源电压
电阻不匹配
基本设置屏幕上把细节内部或外部制动电阻的正确的页
电阻有线不正确的
检查电线(见产品手册)。内部制动电阻桥必须出席于连接器!外部制动电阻桥必须去掉连接头
电阻缺陷
更换保险丝
制动坡道太短
延长制动坡道对速度环屏幕页面
直流母线不与其它放大器
在多个放大器来自同一个位置,连直流环节(见产品手册)
F03*
下面的错误信息的位置控制器(OPMODE 5或6只)
轴机械紧或阻断
机械检查系统
坡道设置扭矩不足
Travel along flatter ramps (ACC,DEC)
电机振动.
参数适应
表时间运动任务基地太低.
增加目标次或使用一个电机有较高的名义速度
反馈错误的电机插入
检查和正确的分配
电机阶段倒
检查销作业
反馈错误设置
设定角度偏移正确(MPHASE)
F09
EEPROM校验和误差
关掉放大器在存储过程
输入参数和保存他们
手动修改参数记录保存到卡.
改变到大写小写字体
硬件故障
到伺服放大器制造商进行维修
放大器有缺陷的
温度与测试旋转或SinCos接口
没用的恒温开关/元素
ContactCustomer Support
F07
内部电压故障
外部短路和过载在电源电压
断开所有的连接器除了24 V和检查是否发生错误地,当你打开
24 V放大器的逻辑
使用稳定24V电压
电机制动与过量的功率现状.
坚持最大电机制动电流(见产品说明书);提供制动与外部电压.
适应参数或硬件
F20
槽误差
硬件错误和扩展卡
在案件的I / O-14/08扩展卡,检查信用卡的外部供电单元
错误PROFIBUS卡
联系客户支持
固件不支持卡插入。
联系客户支持
卡不能正确地插入
卡片移除,并插入新的一和紧它按照说明,在产品手册。
的功耗的插卡太高了.
联系客户支持
F21
处理误差
软件上的错误扩展卡
联系客户支持
MBRAKE设置为0
电机制动功耗电流太低了。
提高当前消费最低150毫安(如通过并联电阻)。
硬件故障
到伺服放大器制造商进行维修
F12
电机阶段
盾对电机电缆附件或丢失严重
检查屏蔽连接
强大的外部电磁干扰
额外的设计电机的盾牌在安装板的开关柜。
电机电缆能力太高了
使用一个电机掐/缩短电缆和使用电缆
安装电机接触器不打开的时间
散热片温度过高
调整系统设置温度（80）或降低环境温度
放大器过脏
检查/吹出通风槽。使用空气过滤器。
风扇的缺陷/没有通电
检查空气流量/风扇的噪音;如果有瑕疵,送功放制造商进行维修.
MAXTEMPH太小了