GLK-Z成套装置说明书
SKZ速关控制装置说明
SKZ速关控制装置说明书宁波质诚液压机械有限公司目录1. 概述1.1说明1.2技术参数2. 功能与原理2.1基本模块2.1.1组成2.1.2功能2.1.3作用原理2.2冗余模块2.2.1组成2.2.2功能2.2.3作用原理2.3启动模块2.3.1组成2.3.2功能2.3.3作用原理2.4抽气模块2.4.1组成2.4.2功能2.4.3作用原理3. 安装与试验3.1安装3.2试验4. 随机资料与注意事项4.1随机资料4.2注意事项5. 故障分析与排除1.概述1.1说明速关控制装置是汽轮机保安系统和控制系统的集合。
它将原来该系统中单个部套组合在一起。
这样，克服了管路繁多、安装复杂的缺陷，在运行中也避免了监控困难和产生漏油着火的事故，增加了汽轮机运行可靠性和安全性。
速关控制装置能实现汽轮机正常启动与停机、电动与手动紧急停机、速关阀和危急遮断器自动挂钩，抽汽速关阀阀的开启和关闭。
为了增加安全性，速关控制装置还设置了电动紧急停机的冗余系统。
以上功能分别由基本模块、冗余模块、启动模块，抽汽模块来实现。
1.2 技术参数1.2.1 液压参数油源压力 0.8MPa (0.6～1.2MPa)工作介质透平油 32# 46#过滤精度≤40μm液体温度 10～70℃1.2.2 电参数电源电压 24VDC（1±10%）220VAC220VDC1.2.3 环境温度 -20～80℃1.2.4 保护种类 IP65（不防爆）EExd11cT4(防爆）用户在订货时必须注明保护种类。
2.功能与原理2.1 基本模块2.1.1 组成手动停机阀（2274）电磁阀（2225）电磁阀（2226）停机卸荷阀（2030）停机卸荷阀（2040）调节油切换阀（2050）速关阀在线试验阀（1845）2.1.2 功能手动紧急停机电动紧急停机速关阀在线试验2.1.3 作用原理高压油从“P”进入基本模块，在基本模块壳体内分为五路。
第一路经手动停机阀（2274）和电磁阀（2225）进入停机卸荷阀 (2030），克服弹簧力使阀处于关闭状态。
2007-2014 Jeep JK 4门 2wd 4wd 3.5英寸基本拓展弹簧抬高系统说明书
55801B/55802BRevised 8.6.14PRO COMP SUSPENSION400 W. Artesia Blvd. Compton, CA 90220 Fax: (310) 747-3912 Ph: 1-800-776-0767E-Mail:*******************Website: This document contains very important information that includes warranty information and instructions forLatest RevisionDate: 8.6.1455801B K3100B2007-2014 JEEP JK 4 Door 2wd/4wd 3 1/2” Basic Coil Spring Lift KitParts ListPart # Description Qty. K3100B926511 FRONTSHOCK 2SHOCK 2926501 REAR55801B JEEP JK 4-DOOR 3.5” KIT:SPRING 2 55358-1 FRONTCOIL55359-1 REAR COIL SPRING 291-8282 STANDARD FRONT TRACK BAR 1SPACERS 2 90-4532 HIGH-MISALIGNMENT91-8283 REAR ADJUSTABLE TRACK BAR 1SPACERS 2 90-4532 HIGH-MISALIGNMENT12127 SHOCK BOOT PAIR 290-6898B 90-6898B90-6525 HARDWARE PACK: Front/Rear Brake Line Brackets 125C100HCS8Y 1/4”-20 X 1 HEX BOLT GR. 8 4 1,3 5,7 425CNUCZ 1/4”-20 STOVER NUT GR. C 4 1,3 5,7 425NWSAZ 1/4” SAE FLAT WASHER 8 1,3 5,7 8 10999 11" ZIP TIE: Black 490-4337 BRAKE LINE SLEEVING 290-7203 FRONT BRAKE LINE BRACKET: Drvr 190-7204 FRONT BRAKE LINE BRACKET: Pass 190-1083 REAR BRAKE LINE DROP 290-1539 BRAKE LINE EXTENSION BRACKET 290-6919 HARDWARE PACK: Rear Sway Bar Link 191-8012 REAR SWAY BAR LINK 245359 5/8” RUBBER HOURGLASS BUSHING 451792 SLEEVE: 5/8” X 1/2” X 1.37” 490-6526 HARDWARE PACK: Rear Sway Bar End Links 1.120C600HCS1Y 12mm-1.75 X 60mm HEX BOLT Gr. 10.9 4.120CNUCZ 12mm-1.75 STOVER NUT Gr. C 4.120NWHDY 12mm HARDENED FLAT WASHER 8 ORK3102BSHOCK 2 926511 FRONTSHOCK 2926501 REAR55802B JEEP JK 2-DOOR 3.5” KIT:SPRING 2COIL55350-1 FRONTPart # Description Qty.55351-1 REAR COIL SPRING 291-8282 STANDARD FRONT TRACK BAR 190-4532 HIGH-MISALIGNMENTSPACERS 2 91-8283 REAR ADJUSTABLE TRACK BAR 1SPACERS 290-4532 HIGH-MISALIGNMENT12127 SHOCK BOOT PAIR 290-6898B 90-6898B90-6525 HARDWARE PACK: Front/Rear Brake Line Brackets 125C100HCS8Y 1/4”-20 X 1 HEX BOLT GR. 8 4 1,3 5,7 425CNUCZ 1/4”-20 STOVER NUT GR. C 4 1,3 5,7 425NWSAZ 1/4” SAE FLAT WASHER 8 1,3 5,7 810999 11" ZIP TIE: Black 490-4337 BRAKE LINE SLEEVING 290-7203 FRONT BRAKE LINE BRACKET: Drvr 1 90-7204 FRONT BRAKE LINE BRACKET: Pass 1 90-1083 REAR BRAKE LINE DROP 2 90-1539 BRAKE LINE EXTENSION BRACKET 290-6919 HARDWARE PACK: Rear Sway Bar Link 1 91-8012 REAR SWAY BAR LINK 2 45359 5/8” RUBBER HOURGLASS BUSHING 451792 SLEEVE: 5/8” X 1/2” X 1.37” 490-6526 HARDWARE PACK: Rear Sway Bar End Links 1 .120C600HCS1Y 12mm-1.75 X 60mm HEX BOLT Gr. 10.9 4.120CNUCZ 12mm-1.75 STOVER NUT Gr. C 4.120NWHDY 12mm HARDENED FLAT WASHER 855801B/55802BRevised Introduction:8.6.14♦ This installation requires a professional mechanic!♦ We recommend that you have access to a factory service manual for your vehicle to assist in the disassem-bly and reassembly of your vehicle. It contains a wealth of detailed information.♦ Prior to installation, carefully inspect the vehicle’s steering and driveline systems paying close attention to the tie rod ends, ball joints, wheel bearing preload, pitman and idler arm. Additionally, check steering-to-frame and suspension-to-frame attaching points for stress cracks. The overall vehicle must be in excellent working condition. Repair or replace all worn or damaged parts!♦ Read the instructions carefully and study the illustrations before attempting installation! You may save your-self a lot of extra work.♦ Check the parts and hardware against the parts list to assure that your kit is complete. Separating parts ac-cording to the areas where they will be used and placing the hardware with the brackets before you begin will save installation time.♦ Check the special equipment list and ensure the availability of these tools.♦ Secure and properly block vehicle prior to beginning installation.♦ ALWAYS wear safety glasses when using power tools or working under the vehicle!♦ Use caution when cutting is required under the vehicle. The factory undercoating is flammable. Take appro-priate precautions. Have a fire extinguisher close at hand.♦ Foot pound torque readings are listed on the Torque Specifications chart at the end of the instructions.These are to be used unless specifically directed otherwise. Apply thread lock retaining compound where specified.♦ Please note that while every effort is made to ensure that the installation of your Pro Comp lift kit is a positive experience, variations in construction and assembly in the vehicle manu-facturing process will virtually ensure that some parts may seem difficult to install. Addition-ally, the current trend in manufacturing of vehicles results in a frame that is highly flexible and may shift slightly on disassembly prior to installation. The use of pry bars and tapered punches for alignment is considered normal and usually does not indicate a faulty product.However, if you are uncertain about some aspect of the installation process, please feel free to call our tech support department at the number listed on the cover page. We do not recom-mend that you modify the Pro Comp parts in any way as this will void any warranty ex-pressed or implied by the Pro Comp Suspension company.Optional Equipment Available from your Pro Comp Distributor!2007-2014:55747B: JEEP (JK) STAGE 3 SUSPENSION 6” LONG ARM LIFT KIT23700B: JK LIGHT BAR20-65227: FRONT ARM CAMS:20-65228: REAR ARM CAMSPARTS:REPLACEMENTKMX-L12: ROD END, 3/4" X 3/4" LHSJNL12: 3/4" STEEL L.H. JAM NUT90-60010 HARWARE PACK: TRACK BAR BUSHINGSFRONT INSTALLATION:1/4” X 1” BoltOE BoltBrake Line Bracket 90-7203 drvr and 90-7204 passFront Spring PadIllustration 1Front Brake LineBracketOE ABS lines with the provided protec-tive sleeves (90-4337) and secure with the supplied zip ties (10999).16. Install the previously removed OE rearsway bar end link into the front sway barmounting bracket on the front axle usingthe previously removed OE hardware. 17. Bolt the remaining end of the OE rearsway bar end link to the front sway barusing the using the OE hardware. Torque the OE hardware according to the manu-facturers specifications.18. Install the shock boots (12127) onto thestem of the shock. Install your new frontshocks (926511 w/shaft end up) usingthe OE hardware. Torque the uppermounting hardware to 17 ft./lbs. and thelower to 35 ft./lbs.19. On both sides of the vehicle, check therouting of the brake lines and the ABSwire harnesses. There must be nopinching, rubbing, or stretching of eithercomponent. At full droop, cycle thesteering from lock to lock whileobserving the reaction of thesecomponents. Reposition them if needed. 20. Reinstall the front wheels and lower thevehicle to the ground. Torque the lugnuts according to the wheel manufacturers recommendations.21. Insert the high-misalignment spacers (90-4532) into the front track bar (91-8282)rod end. See ILLUSTRATION 2.NOTE: The spacers are a tight fit.A press might be needed to fit the spacers into the rod end.22. Install the bushing end of the track barassembly (91-8282) into the passengerside axle track bar mount using the OEhardware. Torque this bolt to 103 ft./lbs.See ILLUSTRATION 3.23. The driver side track bar rod end andmounting bolt will be installed and finaladjustments will be made during the rearinstallation, step 18.REAR INSTALLATION:1. Block the front tires and raise the rear ofthe vehicle. Support the frame with jackstands forward of the rear springs.2. Remove the rear wheels.3. Unbolt the rear track bar from the vehicle.Save the hardware for reinstallation.4. Unbolt the rear brake line bracket fromthe vehicle. Save the OE hardware forreinstallation.5. Remove the shocks on both sides of thevehicle. It may be necessary that youslightly raise the axle to unload the shocks for removal.6. Lower the rear axle enough to remove thecoil springs from the rear spring pockets.Save the factory isolators for re-use.NOTE: Be sure to support the axle while the springs and shocks are re-moved.7. Carefully lower the rear axle to ease inthe new rear coil spring installation. Us-ing the factory isolators install the ProComp rear coil springs (55359-2 4-doorOR 55351-1 2-door) into the spring buck-ets and raise the rear axle into place.Make sure the coil spring seats properlyon the lower spring perch.NOTE: Be sure to reinstall the fac-place.8. Assemble the rear sway bar end links (91-8012) using the supplied bushings(45359) and sleeves (51792) from hard-ware pack (90-6919). See ILLUSTRA-TION 5.9. Install the rear sway bar end link (91-8012) into original mounting bracket onthe axle using the supplied 12mm X60mm bolts and hardware.10. Bolt the remaining end of the sway barend link to the rear sway bar using theusing the supplied 12mm X 60mm boltsand hardware. Torque the 12mm hard-ware to 75 ft./lbs.11. Install the shock boots (12127) onto thestem of the shock. Install your new rearshocks (926501w/shaft end up) usingthe OE hardware. Torque the uppermounting hardware to 20 ft./lbs. and thelower to 35 ft./lbs.12. Install the rear brake line brackets (90-1083) to the original mounting holes andsecure using the previously removed OEbolt.13. Secure the OE brake line brackets to thenew brackets using provided 1/4” X 1”bolts and hardware from pack (90-6525).14. On both sides of the vehicle, check the(Rear)Sway BarLink91-8012Illustration 5Rear Sway Bar End LinkAssemblySleeve51792Bushing45359routing of the brake lines and the ABS wire harnesses. There must be no pinching,rubbing, or stretching of either component.Reposition them if needed.NOTE: Recheck all lines at full droop 15. Reinstall the rear wheels and lower thevehicle to the ground. Torque the lugnuts according to the wheel manufacturers recommendations.16. Insert the high-misalignment spacers (90-4532) into the rear track bar (91-8283)rod end. See ILLUSTRATION 4.NOTE: The spacers are a tight fit.A press might be needed to fit the spacers into the rod end.17. Install the bushing end of the track barassembly (91-8283) into the driver sideaxle track bar mount using the previously removed OE hardware. Torque this boltto 103 ft. lbs.18. With the vehicle fully on the ground, cen-ter the front and rear differential to thevehicle chassis by measuring the clear-ance between each tire and inner fender.This is easier done with assistance. Mov-ing the steering wheel back and forth will assist in connecting the front track bar.When the axles are centered, screw therod ends in or out until the OE bolts fitthrough the frame mount holes and theholes in the rod ends with ease. Secureusing the OE nut plate. Torque the boltsto 125 ft./lbs.19. Position your vehicle on a smooth, flat,hard surface (i.e. concrete or asphalt). 20. Drive the vehicle forward and backward afew feet to be sure that the axle is ad-justed properly and the vehicle is tracking in a straight line.21. Unlock the ignition key and loosen thedrag link adjustment collar.Center the steering wheel by rotating the drag link counter clockwise until the steering wheel is centered. Re-torque the drag link adjustment collars to 26 ft./lbs.IMPORTANT!: If the steering wheel is not centered properly it will trigger the anti-lock brake and traction control warning lights.NOTES:⇒ On completion of the installation, have the suspension and head-lights re-aligned.⇒ After 100 miles recheck for proper torque on all newly installed hard-ware.⇒ Recheck all hardware for tightness after off road use.Revision Page:3.20.14: Changed step 17, pg. 8 to read driver.7.8.14: Changed rear sway bar end link PN 91-2009 to 91-8012 . Edited options box. Modi-fied note on pg. 4 and step 18. Consolidated front and rear track bar adjustment to rear install step 18. Updated kit fitment to include 2014.8.6.14: Added 55802/K3102B info to cover, BOM, and text.55801B/55802BRevised8.6.1411 The PRO COMP PROMISE WARRANTY At Pro Comp, we know you have many choices when selecting products to personalize your vehicle. You should demand nothing but the highest quality available and have total confidence that the products you selected are the best in the industry. It is for these reasons that Pro Comp Suspension products are backed by the best warranty in the industry...the Pro Comp Promise!Pro Comp promises that its products will last a lifetime or we will replace it free of charge. It’s that simple! Because of our commitment to quality and manufacturing excellence, we are able to stand behind our products. FOREVER. It is Pro Comp’s Promise that if one of our suspension products breaks not due to misuse, neglect or vandalism, we will replace it. Whether you are the original purchaser or not, you can be assured that we will make it right. The Pro Comp Promise covers all suspension products including shocks and steering stabilizers. Buy Pro Comp Suspen-sion today and enjoy it for the rest of your life!That’s our Pro Comp Promise!Notice to Owner, Operator, Dealer and Installer: Vehicles that have been enhanced for off-road performance often have unique handling characteristics due to the higher center of gravity and larger tires. This vehicle may handle, react and stop differently than many passenger cars or unmodified vehicles, both on and off–road. You must drive your vehicle safely! Extreme care should always be taken to prevent vehicle rollover or loss of control, which can result in serious injury or even death. Always avoid sudden sharp turns or abrupt maneuvers and allow more time and distance for braking! Pro Comp reminds you to fasten your seat belts at all times and reduce speed! We will gladly answer any questions concerning the design, function, maintenance and correct use of our products.Please make sure that the Dealer / Installer explains and delivers all warning notices, warranty forms and instruc-tion sheets included with Pro Comp product.Warranty and Return Policy:Pro Comp warranties its full line of products to be free from defects in workmanship and materials for the life of the product. Pro Comp’s obligation under this warranty is limited to repair or replacement, at Pro Comp’s option, of the defective product. Any and all costs of removal, installation, freight or incidental or consequential damages are ex-pressly excluded from this warranty. Pro Comp is not responsible for damages and / or warranty of other vehicle parts related or non-related to the installation of Pro Comp product. A consumer who makes the decision to modify his vehicle with aftermarket components of any kind will assume all risk and responsibility for potential damagesincurred as a result of their chosen modifications. Warranty coverage does not include consumer opinions regarding ride comfort, fitment and design. Warranty claims can be made directly with Pro Comp or at any factory authorized Pro Comp dealer.IMPORTANT! To validate the warranty on this purchase please be sure to mail in the warranty card.Claims not covered under warranty* Parts subject to normal wear; this includes bushings, bump stops, ball joints, tie rod ends and heim joints. * Finish after 90 days.* Damage caused as a result of not following recommendations or requirements called out in the installation manu-als.Pro Comp MX Series coil-over shocks are considered a serviceable shock with a one-year warranty against leak-age only. Rebuild service and replacement parts will be available and sold separately by Pro Comp. Contact Pro Comp for specific service charges. Pro Comp accepts no responsibility for any altered product, improper installa-tion, lack of or improper maintenance or improper use of our products.E-Mail:*******************Website: Fax: (310) 747-3912Ph: 1-800-776-0767 HERE: __________________ WARRANTY REGISTRATION NUMBERPLACE。
ZBK系列数字式微机保护装置说明书(精)
ZBK系列数字式微机保护装置技术说明书湖南江河机电自动化工程有限公司目录第一章 ZBK系列产品概述 (41、装置简介 (42、产品分类列表: (43、性能特点 (44、技术指标 (55、硬件结构 (96、功能简介 (107、装置菜单一览表 (128、装置系统配置设定 (139、人机接口操作 (1410、装置安装尺寸 (15第二章 ZBK系列装置安装及调试 (171、调试资料及试验仪器准备 (172、通电前检查 (173、通电试验 (184、异常处理 (205、投运说明及注意事项 (21第三章 ZBK数字式变压器保护测控装置 (221、功能配置 (222、保护原理 (223、定值整定 (304、面板指示灯定义 (365、装置接线 (36第四章 ZBK21型数字式线路保护装置 (371、功能配置 (372、保护原理 (373、定值整定 (434、面板指示灯定义 (465、装置接线 (46第五章 ZBK30型数字式电容器保护测控装置 (471、功能配置 (472、保护原理 (473、定值整定 (504、面板告警指示灯定义 (515、装置接线 (52第六章 ZBK40型数字式分段保护测控装置 (531、功能配置 (532、保护原理 (533、定值整定 (544、面板告警指示灯定义 (555、装置接线 (56第七章 ZBK50型数字式母线电压监测装置 (571.功能配置 (572.保护控制原理 (573.定值整定 (594.面板告警指示灯定义 (605.装置接线 (61第八章数字式发电机保护测控装置 (621、功能配置 (622、保护原理 (633、定值整定 (744、面板指示灯定义 (785、装置接线 (79第九章 ZBK65型数字式电动机保护测控装置 (801、功能配置 (802、保护原理 (803、定值整定 (884、面板告警指示灯定义 (905、装置接线 (91第十章备用电源自投装置 (921.功能配置 (922.几种主要的接线方式及备自投配置选型 (923.ZBK70进线备自投装置原理 (954.ZBK71型主变备自投装置 (1025.ZBK72厂用变备自投装置 (108第一章 ZBK系列产品概述1、装置简介ZBK系列数字式保护测控装置,主要应用于110kV及以下电压等级的变电站、开关站、泵站、电厂等,集保护、控制、测量、通信、录波功能于一体,实现对电力系统发供电设备的保护、测量及监控功能。
3MK2010-XZ2机械使用说明书
-XZ2
使用说明书
3MK2010—SM-03
共 5页
第2 页
揿“循环启动”按钮,机床即开始进行自动返修磨削。它与 毛坯磨削不同之处是进给（X 轴），直接快趋到设置点后直接转换 成精磨速度进行磨削，直到一批零件全部“返修”完毕为止。再揿 “复位”按钮，机床即停止返修。
QR7.3-37
3MK2010 型
数控轴承套圈内圆磨床
使用说明书
(共二册)第一册 机械部分 最大工件内径 100mm 出厂编号
中华人民共和国
无锡机床股份有限公司
-XZ2
使用说明书
共二册 第一册
机械部分
目录
序号
名称
编号
1
注意事项
SM－00
2
机床用途和适用范围
SM－01
3
技术参数
SM－02
4
传动系统和工作循环
共 9页
第 8页
图 4.6 润滑系统
-XZ2
使用说明书
3MK2010-SM-04
共 9页
第 9页
图 4.7 上下料机构
-XZ2
使用说明书
3MK2010-SM-05
共4 页
第1 页
5． 液压系统（参照图 5.1 液压原理图，图 5.2 液压管道示意图） 5.1 液压系统用油 5.1.1 液压油的选择： 机床液压系统采用高级抗磨液压油，油的运动粘度在 13.5～50.6mm² /s 之 间。由于环境温度对油的运动粘度影响较大，因此建议在通常情况下采用 HM-32 高级抗磨液压油。当环境温度在 10℃以下时采用 HM-15 高级抗磨液压油。环境 温度在 30℃以上时采用 HM-46 高级抗磨液压油。
KM-KZ智能操控装置使用说明书
X1/36 140 ln408 ln416
YHJ YTJ
BTJ
HHJ
133 ln409 X1/38
TBJ
TYJ
TBJV
X1/61
ln305
X1/62 X1/63 X1/64 X1/65
ln306 ln307 ln308 ln309
ln310
X1/66 13 ln311
ln312
X1/67 17 ln313
(开孔尺寸图)
注意事项： 在对一次系统做 工频耐压实验， 须将端子拔出后 短 接 。 2"～ 7"均 为外接设备常开 接点，不能接入 强电信号，否则 用户自己承担维 修费用。
公共端
储能
工作位置指示
实验位置指示
断路器状态指示
接地刀闸分合
备用
装置电源
+
220 -
闭锁输出
（常闭）
相
电压传感器 相
相
接 地 /零 线
≤10W
五、接线端子图及安装尺寸
KM-KZ 经济型： 外形尺寸 （单位 mm）：132（水平方向）×205（竖直方向）×45.5（厚度） 开孔尺寸 （单位 mm）：117（水平方向）×180（竖直方向） 固定螺丝孔（单位 mm）：116（水平方向）、191（竖直方向）处开 4 个直径为 4.5mm 圆孔
安徽凯民电力技术有限公司
KM-KZ-5 智能型：
外形尺寸 （单位 mm）：230（水平方向）×178（竖直方向）×83（厚度） 开孔尺寸 （单位 mm）：220（水平方向）×165（竖直方向）
二次回路接线示意图
2ZZK
QF
X1/50
CZ/3
CZ/13
SKZ速关控制装置说明书
目 录1. 概述1.1说明1.2技术参数2. 功能与原理2.1基本模块2.1.1组成2.1.2功能2.1.3作用原理2.2冗余模块2.2.1组成2.2.2功能2.2.3作用原理2.3启动模块2.3.1组成2.3.2功能2.3.3作用原理3. 安装与试验3.1安装3.2试验4. 随机资料与注意事项 4.1随机资料4.2注意事项5. 故障分析与排除1.概述1.1说明速关控制装置是汽轮机保安系统和控制系统的集合。
它将原来该系统中单个部套组合在一起。
这样，克服了管路繁多、安装复杂的缺陷，在运行中也避免了监控困难和产生漏油着火的事故，增加了汽轮机运行可靠性和安全性。
速关控制装置能实现汽轮机正常启动与停机、电动与手动紧急停机、速关阀和危急遮断器自动挂钩。
为了增加安全性，速关控制装置还设置了电动紧急停机的冗余系统。
以上功能分别由基本模块、冗余模块、启动模块来实现。
1.2 技术参数1.2.1 液压参数油源压力 0.8MPa (0.6～1.2MPa)工作介质 透平油 32# 46#过滤精度 ≤40μm液体温度 10～70℃1.2.2 电参数电源电压24VDC（1±10%）1.2.3 环境温度 -20～80℃1.2.4 保护种类 IP65（不防爆）EExd11cT4(防爆）用户在订货时必须注明保护种类。
2.功能与原理2.1 基本模块2.1.1 组成手动停机阀 （2274）电磁阀 （2225）停机卸荷阀 （2030）调节油切换阀 （2050）速关阀在线试验阀（1845）2.1.2 功能手动紧急停机电动紧急停机速关阀在线试验2.1.3 作用原理高压油从“P”进入基本模块，在基本模块壳体内分为五路。
第一路经手动停机阀（2274）和电磁阀（2225）进入停机卸荷阀 (2030），克服弹簧力使阀处于关闭状态。
正常运行时，通向停机卸荷阀的速关油不泄油。
速关油是由冗余模块内部管路引入的。
第二路油经调节油切换阀（2050）变为调节控制油经冗余模块内部管路进入启动模块成为电液转换器供油。
SHK-ZXK 开关柜状态显示仪说明书word资料7页
SHK―ZXK系列开关柜状态智能显示仪上海合凯电力保护设备有限公司SHK―ZXK系列开关柜状态智能显示仪的适用范围■适用于户内3～35kV系统；■适用于中置柜、手车柜、固定柜、环网柜等多种开关柜，用以显示手车、断路器、接地刀闸位置及柜内温湿度。
SHK―ZXK系列开关柜状态智能显示仪的功能■断路器的状态显示、手车位置显示、隔离刀和接地刀状态显示、储能显示开关柜状态智能显示仪（以下简称“智能显示仪”）的一次系统模拟图见图1。
断路器手车处于工作位置时，发光柱1红色垂直模拟条发光；手车处于试验位置时，发光柱1绿色水平模拟条发光；断路器手车位于试验和工作位置之间时，发光柱1红色垂直和绿色水平模拟条同时闪烁；断路器手车移出开关柜时，发光柱1红色垂直和绿色水平模拟条均不发光，表示手车已断电。
接地刀闸处于合闸状态时，发光柱3红色竖直模拟条发光；接地刀闸断开时，发光柱3绿色模拟条发光，表示接地刀闸分闸。
断路器处于合闸状态时，其常开节点闭合、常闭节点打开，发光柱2红色竖直模拟条发光；断路器常开节点打开、常闭节点闭合时，发光柱2绿色模拟条发光，表示断路器已分闸。
■操控装置(SHK-ZXK-4型)面板带有：分闸/合闸转换开关；远方/就地转换开关；储能转换开关；柜内照明转换开关。
分闸/合闸转换开关：“分闸”位置时3-4、7-8触点接通，“合闸”位置时，1-2、5-6触点接通，当自动恢复到“0”状态时，所有节点全部断开。
远方/就地转换开关：“远方”位置时3-4、7-8触点接通，“就地”位置时，1-2、5-6触点接通。
储能转换开关：3位长柄选择开关，有常开、常闭触点各一组。
柜内照明转换开关：2位长柄选择开关，有常开、常闭触点各一组。
■高压带电显示当A、B或C相带电时，面板上相应的指示灯亮，同时提供带电闭锁接点。
LED启动电压为额定相电压的15～65%。
闭锁启控电压为额定相电压的65%。
当三相同时带电或有一相带电时，闭锁灯亮，启动电磁锁动作。
Kohler ECH630-ECH749、CH735 CH26、CH745发动机用户手册说明书
24 590 51 修订 B ZH9ECH630-ECH749, CH735/CH26, CH745用户手册重要提示：设备操作前请阅读所有安全预防措施和说明。
请参阅安装该发动机设备的操作说明。
执行任何保养或检修前请确保发动机已停机并平坦放置。
保修范围在保修卡及 中扼要说明。
它具体规定了您的权利和义务，请仔细阅读。
为了符合适用的排放规定，排气系统反压不可超过限制，可参阅 。
根据型号进行搜索，然后选择规格标签。
Kohler 发动机在 网站上已公布二氧化碳值。
请记录发动机信息，并在订购零件或获取保修范围时参考。
发动机型号规格系列号购买日期ECV630-ECV749, CV735, CV74524 590 51 修订 B 10易爆炸的燃油可能引起火灾和严重灼伤。
在发动机处于高温或运转时，切勿往燃油箱内加油。
汽油很容易燃烧，且它的蒸气被点燃的时候易爆炸。
存警告高温零件可能引起严重灼伤。
切勿在运转期间或停机后立即触摸发动机。
在发动机防热罩或隔热板拆走后，切记不能运行发动机。
警告旋转零件可能引起严重人身伤害。
切记远离运转中的发动机。
手、足、头发和衣物必须远离正在转动的零件以防人身伤害。
在外盖、保护罩或防护装置拆走的时候，不要运行发动机。
警告意外起动可能造成严重人身伤害甚至死亡。
在维护前请断开火花塞导线并将其接地。
在发动机或设备上工作之前，请按以下说明停止发动机：1)断开火花塞导线。
2) 断开电池的负极 (–) 电池线。
警告一氧化碳可能导致严重呕吐、昏厥甚至死亡。
避免吸入排放的尾气。
切勿在室内或密闭空间内运行发动机。
发动机排放的尾气含有有毒的一氧化碳。
一氧化碳是无味、无色的气体，且吸入过多时会导致死亡。
警告： 可能导致死亡、严重人身伤害或重大财产损失的危险。
告诫：可能导致轻微人身伤害或财产损失的危险。
注意： 用于告知人们非常重要的发动机安装、操作或保养相关信息。
高压液体可能刺破皮肤，并造成严重人身伤害甚至死亡。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
1
杭州银湖电气设备有限公司
一、安全预防
1.1 安全预防
电气设备应该让有资格的专业人员进行安装、操作、使用、维护。本说明书 是针对经过培训的专业人员使用的操作手册，未按使用操作而造成不良后果，本 公司将不负任何责任。
! 注 意
电击、燃烧和爆炸的危险 ·只有专业人员才能安装这个设备，并且要完整通读使用说明书之后。 ·不要单独工作。 ·对此设备做检查、测试和维护之前，先要断开所有电源连接。 ·对电源系统的设计要特别注意，考虑所有的电源，包括反送电的可 能性。 ·要使用正确调整电压的检测设备来确定所有的电源都已断开。 ·当心潜在的危险，做好个人防护装具，仔细检查设备内的工作区域 看是否有工具和其它遗留物体。 ·当移除或安装面板时注意不要碰到电源线，避免操作面板上钉钉， 以免造成个人伤害。 ·这个设备的成功运行依赖于正确的处理，安装的操作。忽略基本的 安装要求可能造成个人的伤害，也可能损坏电气设备或者其它物体。 不执行此说明将可能导致人身伤亡。二．GLK-Z 型成套装置概述
2.1 概述
GLK-Z 型高压无功自动补偿成套装置由若干组 LC-Z 型滤波支路组成。每 组（柜）内含真空接触器（断路器） 、电压互感器、电流互感器、滤波电抗器、 滤波电容器及相应控制、保护器件.一般为组装在一个柜体内的一体化装置。专 门为冶金、钢铁、机械、水泥、交通、化工等行业 6kv、10kv 系统谐波较大场所 设计制造的。 本成套装置可以是一个滤波支路和一个控制器，单独成套，也可以是二至 六组滤波支路共用一个控制器，由内部母排连接后组成一套。
3
杭州银湖电气设备有限公司
2.3 规格型号
GLK-Z 型 高压自动补偿滤波成套装置
说 明 书
杭州银湖电气设备有限公司
Hang Zhou Yin Hu Electrical Equipment Co., Ltd.
杭州银湖电气设备有限公司
一、安全预防 ................................................................................................................................... 2 1.1 安全预防 ..................................................................................................................................... 2 二．GLK-Z 型成套装置概述 .............................................................................................................. 3 2.1 概述 ............................................................................................................................................. 3 2.2 工作原理 ..................................................................................................................................... 3 2.3 规格型号 ..................................................................................................................................... 4 2.4 适用标准 ..................................................................................................................................... 4 2.5 使用环境条件.............................................................................................................................. 5 2.6 电气要求 ..................................................................................................................................... 5 2.7 结构要求 ..................................................................................................................................... 6 2.8 组成部件 ..................................................................................................................................... 6 2.9 主要功能 ..................................................................................................................................... 7 2.10 技术性能 ................................................................................................................................... 7 三、GLK 型高压补偿滤波自动综合控制器....................................................................................... 9 3.1 控制器使用与操作 ...................................................................................................................... 9 四．运输、交接验收及储存........................................................................................................... 10 4.1 运输 ........................................................................................................................................... 10 4.2 交接验收 .................................................................................................................................. 10 4.3 储存 ........................................................................................................................................... 10 五．安装及操作.............................................................................................................................. 11 5.1 安装 ........................................................................................................................................... 11 5.2 操作 ........................................................................................................................................... 11 5.3 调试 ........................................................................................................................................... 11 六．常规故障及处理 ...................................................................................................................... 14 6.1 补偿装置常见异常情况和故障 ................................................................................................. 14 6.2 运行中的并联电容器经常发生的异常现象和故障................................................................... 14 6.3 成套装置继电保护动作后发出音响信号 .................................................................................. 16 七．运行维护 ................................................................................................................................. 17 八．注意事项 ................................................................................................................................. 19