涂料防腐剂delan201
造纸杀菌剂
3Q-201造纸高效杀菌防腐剂产品说明：3Q-201造纸杀菌防腐剂是由异噻唑啉酮，表面活性剂，稳定剂为主要活性组分的高效、广谱、低毒环保型工业杀菌防腐剂。
用于因腐浆原因而造成的断纸和纸张斑点，孔洞等。
它不会对设备的腐蚀和对纸浆纤维的破坏，能有效的提高纸机的清洁度，减少刷车次数，提高纸张等级，对原色浆的防腐效果显著。
纸浆杀菌防腐剂还可广泛地应用到造纸涂料、淀粉及中性施胶剂的杀菌防腐。
投加于纸浆上机前的混浆池或成浆池，白水系统中。
性能特点：1、杀菌、抑菌、高效、广谱、环保产品2、不含重金属与水溶性好，容易操作。
3、适用的PH范围广，PH2－9均可以使用。
4、解决因腐浆产生纸张洞眼、黑斑、透光点及断纸5、提高纸张的质量。
6、毒性低，可降解，不会对环境产生污染。
质量标准：外观微黄色透明液体有效成份含量（%）10密度(g/ml，200C) 1.26-1.30pH值 2.0-5.0溶解性与水、低分子醇混溶使用方法及用量：白水循环系统等部位添加，能有效控制菌类繁殖、控制纸浆霉变。
使用量为10－20ppm。
包装规格：25kg、250kg闭口塑料桶包装。
注意事项：1.应避免与眼睛直接接触：一旦接触，应立即用大量清水冲洗，不可延误! 不可与皮肤长时间接触。
2.贮存过程中不可与还原性金属接触，如金属铁、铝等以免导致产品分解。
3.本品在pH＞9.0的碱性介质中稳定性差，不宜使用。
亲核性很强的化学品与本品配伍，例如S2-和R-NH2，将导致本品质量下降，甚至完全失效。
贮存：本品在避光和常温下保质期为12个月。
运输：非危险品。
大连天纬化学有限公司的工业杀菌剂，工业防腐剂，工业防霉剂 。
几种常用防腐剂小结
1、K-CG即Kathon CG（凯松）可广泛地应用于在涂料、高分子合成乳液等水性体系及水处理中，其有效成分为异噻唑啉酮衍生物，活性成份为5—氯-2—甲基—4—异噻唑啉—3-酮（cit）、2—甲基-4—异噻唑啉-3—酮（mit）。
性能特点：1。
广谱、长效的杀灭多种细菌、真菌和酵母菌，用量低.2.适用的ph范围广泛，2-9均可使用。
3.与水混溶，可以在任何工序加入,容易操作。
4.毒性低，使用浓度完全无害。
5.排放无残留,不会对环境造成累积污染.6.不燃烧，易于运输,使用方便。
7。
与各种乳化剂、表面活性剂及蛋白质成份配伍性好。
8.对假单包菌有特效，得到了全世界认同。
9.不含甲醛，不含voc。
质量标准：外观微黄色透明液体有效成份含量（％）14氯比2.5—4.0密度（g/ml,20℃）1。
26—1。
33ph值2。
0-3.0稳定性ph 2.0-9。
0稳定应用领域：广泛用于涂料、水性高聚物、金属切割液、胶粘剂、油墨、染料、石蜡液等。
还可用于水处理，如石油化工、电力、中央空调、工业循环冷却水中的杀菌、灭藻。
使用方法及用量：在水处理中使用时，先稀释成1。
5％的水溶液，杀生时视菌藻的滋生情况,每周投加1—2次，投加量为50—300ppm.不能与氯气等氧化性杀生剂同时使用.注意事项：1.本品应避免与眼睛直接接触：一旦接触,应立即用大量清水冲洗,不可延误。
不可与皮肤长时间接触.2。
本品贮存过程中不可与还原性金属接触，如金属铁、铝等以免导致产品分解。
3。
本品在ph＞9。
0的碱性介质中稳定性差，不宜使用.亲核性很强的化学品与本品配伍，例如s2-和r—nh2，将导致本品质量下降，甚至完全失效。
贮存:本品在避光和常温下保质期为12个月。
2、杰马BP水溶性抗菌剂,无色透明粘稠液体，【保存】应贮存于避光、阴凉、干燥处，密闭保存2年。
【用途】杰马BP，化妆品级抗菌剂、防腐剂，可用于膏霜、露液、香波、护发素、湿纸巾等附留型和洗去型产品,该产品得到美国和欧盟批准，广泛用于水包油、油包水的乳化体系和水溶性配方.添加比例0.1-1。
d201树脂说明书
d201树脂说明书
一、产品简介
d201树脂是一种高分子合成材料，具有良好的耐腐蚀性、耐热性、绝缘性和加工性能。
广泛用于化工、石油、电力、环保等领域，作为酸碱反应介质、萃取剂、吸附剂、绝缘材料等。
二、使用说明
1. 储存：d201树脂应储存于干燥、阴凉、通风良好的地方，避免阳光直射和高温。
储存温度应保持在5-30℃，湿度应小于80%。
2. 运输：在运输过程中，应小心轻放，避免剧烈振动和碰撞。
同时要防止树脂受潮和与杂质混合。
3. 配制：使用前应检查包装是否完好，如有损坏应及时更换。
根据实际需要，按比例加入水和树脂，搅拌均匀后即可使用。
4. 使用：使用时应根据实际需求，选择适当的工艺条件，如温度、压力、流量等。
同时要保证设备密封良好，防止树脂泄漏。
5. 维护：定期检查树脂的外观、颜色和性能，如有异常应及时处理。
同时要保持设备清洁，防止杂质的混入。
三、注意事项
1. d201树脂对人体有一定的刺激性，使用时应佩戴防护眼镜和手套等个人防护用品。
2. 在使用过程中，如发现树脂有异味或变色等情况，应立即停止使用，并检查原因。
3. d201树脂为易燃物品，应远离火源和高温。
4. 不宜与氧化剂等化学品混合使用。
5. 使用过程中应保持通风良好，防止吸入有害气体。
ZJ-201型防霉晴雨漆配方与施工工艺
ZJ-201型防霉晴雨漆配方与施工工艺
本晴雨漆是以高品质纯丙烯酸乳液、高档颜料、助剂制成的高级外墙全效功能乳胶漆，无毒无味，符合环保要求，漆膜高度耐水，有极强抗酸耐碱、防霉性能，涂膜富有弹性，可遮盖细小裂纹，附着力强，能与墙面牢固结合，耐候性好，久经雨淋日晒，不产生粉化和墙面脱落，不褪色。
该涂料配方：
组分质量/kg组分质量/kg 界面活性剂
NP-9
0.99消泡剂DH-1110.95
润湿剂DH-1100.61
有机硅改性纯丙
乳液（BP-108型）
92.6
分散剂DH-5071增稠流平剂
RM-2020
24
防霉防腐剂PASTE 3.3
碱溶胀型增稠剂
DH-939
2.5
增黏增稠剂
718A（2%）
10.7蓝色浆0.04
硅酸铝钛粉 5.4氨水适量丙二醇12.8纯净水加至300醇酯十二（成膜
助剂）
5钛白粉（R-940）83.4应用与施工
（1）不要在潮湿或寒冷的天气（气温低于5℃，相对湿度大于85%）情况下施工，否则不能达到预期的涂装效果。
（2）先将墙面尘土、污垢、油垢和其他杂物及松脱的旧漆面清理干净，检查旧漆膜老化情况，彻底清除霉斑。
（3）可加水稀释至10%-20%后使用。
按常规方法批刮耐水腻子，找平、打磨。
（4）涂刷抗碱封闭底漆一遍。
底漆干燥后方可涂刷本晴雨漆两遍。
（5）将本品存放在0-35℃，阴凉、干燥的地方。
未使用完的涂料要密封盖好；产品未开启时，经妥善保存，贮存期可达12个月以上。
中国新型涂料网。
真石漆杀菌防腐剂介绍
涂真石漆杀菌防腐剂即一种异噻复合型防腐剂，因具有杀菌广谱、安全、高效、环保等特点。
且可持续顶层空间保护，不含VOC，不含APEO。
现被广泛应用于建筑涂料、水性工业漆等行业。
一、化学和物理性质外观:无色至浅黄/绿色清澈液体气味:轻微密度(20°C):1.020 - 1.052 g/cm³折射率(20°C): 1.3390 - 1.3450pH (20°C): 3.0 - 5.0溶解性：易溶于水和大多数低分子醇和乙二醇应用稳定性：适宜的使用条件为pH 值2.0 - 9.0 和温度不超过60°C二、杀菌性能涂真石漆杀菌防腐剂对引起水性产品污染和降解的细菌，霉菌和酵母菌有非常广谱的杀菌活性。
可杀灭如下有害微生物及其最低抑制浓度：三、应用/用量可用于保护乳胶漆、聚合物乳液、粘合剂、瓷釉、填充剂、密封胶等水性产品在湿态时免受有害微生物污染，并也可用于稀释的丙烯颜料、色浆等体系中。
推荐使用浓度为0.1 - 0.3%，当然具体浓度还需根据应用的产品及其使用的环境条件。
对于特殊含水量较大的可适当增加添加量，具体添加可向生产厂家询问准确的使用浓度。
四、使用方法/相容性可在生产过程的任何阶段加入，但建议在生产过程中尽早加入, 有利于彻底保护产品。
并且要注意加入时的温度、pH值和氧化还原电势不会影响本产品的稳定性。
同时，涂真石漆杀菌防腐剂与推荐使用的大多数产品配方相容。
还原剂、胺和其它强亲核物质会导致其活性成分降解，因此，初次使用本产品时，建议用户进行试验或者咨询专业的生产厂家。
郑州丰联生物科技有限公司是上海丰联集团旗下负责微生物管控子公司。
是一家研究、开发、生产和销售环境友好型抗生物新材料和生物基可降解高分子材料企业。
其产品不仅具有高效、安全、环保等特点，且价格优惠，因此，现深受客户的好评。
TG201
TG-201双组份聚氨酯防水涂料（911）产品归类：防水涂料系列规格：30Kg/套、1.5Kg/套；铁桶包装产品编号：TG-201产品概述TG-201 双组份聚氨酯防水涂料是采用异氰酸酯为基料合成的高分子化学反应型防水涂料。
双组份按一定比例混合均匀，经过固化后形成均匀的、富有弹性的整体防水胶膜。
适用范围◆混凝土、钢、石棉制品等结构的平屋面、坡屋面、种植屋面等；◆各类地下建筑物的底板及内外墙防水；◆伸缩缝、施工缝、变形缝等；◆防腐地坪、防腐池及管道外的防锈、防腐蚀。
◆其他建筑部位：地铁、隧道、通道、井坑、水池、天沟、厕浴间等；产品特点◆粘结力强、凝固期短，对绝大部分基面有极佳的附着力和粘结能力；◆材料为液态施工，能在凹凸不平或弯曲表面施工，达到可靠无缝密封；◆冷施工，操作方便，可直接喷涂,施工安全，工期短；◆环保，不含煤焦油及有害物质，有机溶剂低，无毒、无害、无污染。
技术指标◆参考用量涂膜固化厚度（mm）参考用量（Kg/m2）1.0 31.2 51.52.12.0 2.62.53.13.0 3.9注：本测试基于本公司实验室进行，现场不同环境条件可能产生异同。
施工指引◆基面处理施工：基面干燥、无粉尘油污，含水率≤8%，预先对节点部位密封增强处理，阴阳角应作半径R20圆弧批抹处理；◆配料：先把A组份放入容器内随后加入B组份，充分搅拌5min以上确保均匀；◆为隔基层潮气，提高基层与涂膜的粘接强度，可涂布一层基层处理剂；◆涂料涂施建议厚度为1.5～2.0mm厚，施工可采用毛刷或橡胶刮板进行施工，要求每层涂刷均匀不露底，且相邻两遍施工方向互相垂直；如遇多个施工段，每段涂料的边皮周边之间防水层搭接长度不少于100mm并平缓过渡；◆涂施两至三遍完成，每遍间隔时间不少于4h，具体视现场环境、气候等条件而定；◆为增加防水层被动粘结力，在最后一道涂层尚未固化前，可在其表面撒上砂；◆完成面建议铺贴无纺布隔离层，再进行保温层、保护层施工。
防腐水性涂料化学品安全技术说明书(防腐漆-MSDS)
防腐水性涂料化学品安全技术说明书(防腐漆-MSDS)防腐水性涂料化学品安全技术说明书（防腐漆-MSDS）1. 概述防腐水性涂料化学品是用于防止金属、木材等材料腐蚀的涂料产品。
本产品采用环保水性配方，具有优良的耐腐蚀性能、附着力和遮盖力，广泛应用于钢结构、管道、船舶、桥梁等领域的防腐保护。
2. 化学品名称和身份- 化学品名称：防腐水性涂料化学品- 化学品身份：水性涂料树脂、水性分散剂、助剂、填料等3. 危险性概述3.1 物理危险- 蒸气压：低蒸气压，不易挥发- 闪点：不适用（水性涂料）- 爆炸极限：不适用3.2 化学危险- 腐蚀性：本产品具有腐蚀性，对皮肤、眼睛等造成刺激和损伤- 毒性：长期接触对神经系统、肝脏、肾脏等造成损害- 燃烧性：不燃，不支持燃烧4. 成分/组成信息本产品主要成分包括水性涂料树脂、水性分散剂、助剂、填料等。
具体成分可能因生产批次不同而有所变化。
5. 急救措施5.1 皮肤接触立即脱去污染的衣物，用大量清水冲洗至少15分钟，必要时就医。
5.2 眼睛接触立即用大量清水冲洗至少15分钟，必要时就医。
5.3 吸入立即将患者移至空气新鲜处，保持呼吸道畅通，必要时就医。
5.4 吞食立即就医。
6. 消防措施由于本产品不燃不爆，火灾时可使用干粉、二氧化碳等灭火器进行灭火。
7. 泄露/溢出处理使用干砂或干粉覆盖泄露物，避免污染环境。
清理泄露物时，请穿戴防护用品。
8. 存储和运输存储于干燥、阴凉、通风良好的环境中，避免阳光直射。
运输时，遵守相关法规，确保安全。
9. 接触控制和个体防护避免皮肤、眼睛等直接接触。
操作时穿戴防护眼镜、手套、口罩等防护用品。
10. 理化性质- 外观：乳白色液体- 比重：约1.0- 溶解性：不溶于水，溶于有机溶剂- 挥发性：低挥发性11. 稳定性和反应性本产品在正常储存和运输条件下稳定，避免与还原剂、强酸、强碱等反应。
12. 生态信息本产品对环境有一定危害，请避免污染水源、土壤等。
冠凯帕蒂柔软清洗涂层液说明书
Product #(s) – 4105Material Safety Data SheetFor Emergency Call:CHEM-TEL (800) 255-3924 24 Hour Assistance1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATIONProduct Name: C hampion Wipe-R-Clean Windshield Washer & De-IcerCAS Number: 67-56-1 / 7732-18-5Recommended Uses: Windshield WashCompany IdentificationManufacturer's Name: CHAMPION BRANDS, LLCAddress: 1001 Golden Drive, Clinton, MO 64735Telephone – General Information: (800) 821-56932. HAZARDS IDENTIFICATIONHazard Classes: Flammable Liquid Category 3Acute Oral Toxicity Category 3Acute Dermal (skin) Toxicity Category 3Acute Inhalation Toxicity Category 3Toxic to Reproduction Category 1BSpecific Target Organ Toxicity (Single Exposure) Category 1 and Category 3Aspiration Hazard Category 1Note: Assigned to classification based on human experienceSignal Word: DANGERHazard Statements:H226 Flammable Liquid and Vapor.H301 Toxic if Swallowed.H304 May be fatal if swallowed and enters airways.H311 Toxic in Contact with Skin.H331 Toxic if Inhaled.H336 May cause drowsiness or dizziness.H360 May Damage Fertility or the Unborn Child – fetotoxic and teratogenic effects.H370 Causes Damage to the Optic Nerve causing blindness if ingested. Precautionary Statements:P101 If medical advice is needed, have product container or label at hand.P102 Keep out of reach of children,P103 Read label before use.P201 Obtain special instructions before use.P202 Do not handle until all safety precautions have been read and understood. P210 Keep away from heat/sparks/open flames/hot surfaces – No smoking.P233 Keep container tightly closed.P240 Ground/bond container and receiving equipment.P241 Use explosion-proof electrical lighting and equipment.Product #(s) – 4105P242 Use only non-sparking tools.P243 Take precautionary measures against static discharge.P261 Avoid breathing vapors.P264 Wash thoroughly after handling.P270 Do not eat, drink or smoke when using this product.P271 Use only outdoors or in a well-ventilated area.P280 Wear protective gloves / protective clothing / eye protection.P301 + P310 If SWALLOWED: Immediately call a POISON CENTER or doctor/physician.P331 D o NOT induce vomiting.P330 Rinse mouth.P303 + P361 + P353 If ON SKIN (or hair): Remove/Take of immediately all contaminated clothing.Rinse skin with water/shower.P304 + P340 IF INHALED: Remove victim to fresh air and keep at rest in a positioncomfortable for breathing.P308 + P311 IF exposed or concerned: Call a POISON CENTER or doctor/physicianP361 + P378 Take off immediately all contaminated clothing and wash it before reuse.P370 + P378 In case of fire: Use dry chemical, CO2, alcohol-resistant foam, and water spray for extinction.P403 + P235 Store in well-ventilated place. Keep cool.P501 Disposal: Dispose of contents/container to a specialized waste disposal plant in accordance with local/regional regulationsHazard Pictograms:3. COMPOSITION/INFORMATION ON INGREDIENTSCAS Num b erComponents Typical WeightPercentageMethanol 22-36% 67-56-1Water 64-78% 7732-18-54. FIRST AIDEyes: If irritation or redness develops, move victim away from exposure and into fresh air. Flush eyes with clean water. If symptoms persist, seek medical attention.Skin: Remove contaminated shoes and clothing and cleanse affected area(s) thoroughly bywashing with mild soap and water. If irritation or redness develops, seek medical attention.Inhalation: If respiratory symptoms develop or other symptoms of exposure develop, move victim away from source of exposure and into fresh air. If symptoms persist, seek medical attention. If victim is not breathing, clear airway and immediately begin artificial respiration. If breathingdifficulties develop, oxygen should be administered by qualified personnel. Seek immediate medical attention.Product #(s) – 4105Ingestion: Aspiration hazard. Do not induce vomiting or give anything by mouth because thismaterial can enter the lungs and cause severe lung damage. If victim is drowsy or unconscious and vomiting, place on the left side with the head down. If possible, do not leave victim unattended and observe closely for adequacy of breathing. Seek immediate medical attention.Note to Physicians: Ethanol significantly decreases the toxicity of methanol because it competes for the same metabolic enzymes, and has been used to treat methanol poisoning.Epinephrine and other sympathomimetic drugs may initiate cardiac arrhythmias in persons exposed to high concentrations of hydrocarbon solvents (e.g., in enclosed spaces or with deliberate abuse).The use of other drugs with less arrhythmogenic potential should be considered. If sympathomimetic drugs are administered, observe for the development of cardiac arrhythmias.Medical Conditions: Exposure to high concentrations of this material may increase the sensitivity of the heart to certain drugs. Persons with pre-existing heart disorders may be more susceptible to this effect (see Note to Physician above).5. FIRE FIGHTING MEASURESSuitable Extinguishing Media: Dry chemical, CO2, water spray or alcohol-resistant foam. .Water spray is recommended to cool or protect exposed materials or structures. Water may be ineffective for extinguishment, unless used under favorable conditions by experienced fire fighters. Carbon dioxide can displace oxygen. Use caution when applying carbon dioxide in confined spaces.Specific Hazards: This material is flammable and can be ignited by heat, sparks, flames or other sources of ignition (e.g., static electricity, pilot lights or mechanical/electrical equipment). Flame is invisible in daylight. Vapors may travel considerable distances to a source of ignition where they can ignite, flashback or explode. May create vapor/air explosion hazard indoors, in confined spaces, outdoors or in sewers. If container is not properly cooled, it can rupture in the heat of a fire. Vapors are heavier than area and can accumulate in low areas.Hazardous Combustion Products: Toxic gases and vapors; oxides of carbon and formaldehyde.Special Firefighting Procedures: For fires beyond the initial stage, emergency responders in the immediate hazard area should wear bunker gear. When the potential chemical hazard is unknown, in enclosed or confined spaces, or when explicitly required by DOT, a self-contained breathingapparatus should be worn. In addition, wear other appropriate protective equipment as conditions warrant (see Section 8). Isolate immediate hazard area and keep unauthorized personnel out. Stop spill/release if it can be done with minimal risk. Move undamaged containers from immediatehazard area if it can be done with minimal risk. Water spray may be useful in minimizing ordispersing vapors and to protect personnel. Cool equipment exposed to fire with water, if it can be done with minimal risk. Avoid spreading burning liquid with water used for cooling purposes.6. ACCIDENTAL RELEASE MEASURESPersonal Precautions: Flammable. Spilling of liquid product will create a fire hazard and may form an explosive atmosphere. Keep all sources of ignition and hot metal surfaces away fromspill/release if safe to do so. The use of explosion-proof equipment is recommended. Stay upwind and away from spill/release. For large spills, notify people down-wind of spill/release, isolateimmediate hazard area and keep unauthorized personnel out. Wear appropriate protectiveequipment including respiratory protection as conditions warrant (see Section 8). See Sections 2 and 7 for additional information on hazards and precautionary measures.Product #(s) – 4105Environmental Precautions: Stop spill/release if it can be done with minimal risk. Prevent spilled material from entering sewers, storm drains, other unauthorized treatment drainage systems, and natural waterways. Use foam on spills to minimize vapors. Use water sparingly to minimizeenvironmental contamination and reduce disposal requirements. If spill occurs on water, notify appropriate authorities. Spills into or upon navigable waters, the contiguous zone, or adjoiningshorelines that cause a sheen or discoloration on the surface water, may require notification of the National Response Center (phone number 800-424-8802).Methods for Containment and Clean-Up: Notify relevant authorities in accordance with allapplicable regulations. Immediate cleanup of any spill is recommended. Dike far ahead of spill for later recovery or disposal. Absorb spill with inert material such as sand, earth or other non-combustible material, and place in suitable container for disposal. If spilled on water remove with appropriate methods (e.g., skimming, booms or absorbents). In case of soil contamination, remove contaminated soil for remediation or disposal, in accordance with local regulations.7. HANDLING AND STORAGEPrecautions for Safe Handling: Keep away from ignition sources such as heat/sparks/open flames – No smoking. Take precautionary measures against static discharge. Non-sparking tools should be used. Wear protective gloves/clothing and eye/face protection. Wash thoroughly after handling.Use good personal hygiene practices and wear appropriate personal protective equipment (see Section 8).Flammable. May vaporize easily at ambient temperatures. The vapor is heavier than air and may create an explosive mixture of vapor and air. Beware of accumulation in confined spaces and low lying areas. Open container slowly to relieve any pressure. Electrostatic charge may accumulate and create a hazardous condition when handling or processing this material. To avoid fire orexplosion, dissipate static electricity during transfer by bonding and grounding containers andequipment before transferring material. The use of explosion-proof equipment is recommended and may be required (see appropriate fire codes). Refer to NFPA-77 and/or API RP 2003 for specific bonding/grounding requirements. Do not enter confined spaces such as tanks or pits withoutfollowing proper entry procedures such as ASTM D-4276 and 29CFR 1910.146. Do not wearcontaminated clothing or shoes. Keep contaminated clothing away from sources of ignition such as sparks or open flames. Use good personal hygiene practice.Conditions for Safe Storage: Keep container(s) tightly closed. Use and store this material in cool, dry, well-ventilated areas away from heat and all sources of ignition. Post area “No Smoking or Open Flame.” Store only in approved containers. Keep away from any incompatible material (see Section 10). Protect container(s) against physical damage. Outdoor or detached storage ispreferred. Indoor storage should meet OSHA standards and appropriate fire codes.8. EXPOSURE CONTROLS/PERSONAL PROTECTIONExposure GuidelinesComponent ACGIH TLV ACGIH STEL OSHA PEL OSHA STELMethanol 200 ppm(Skin) 250 ppm(Skin)200 ppm(Skin)250 ppm(Skin)Product #(s) – 4105Engineering Controls: If current ventilation practices are not adequate to maintain airborneconcentrations below the established exposure limits, additional ventilation or exhaust systems may be required.Specific Personal Protective EquipmentEye/Face Protection: The use of eye protection that meets or exceeds ANSI Z.87.1 isrecommended to protect against potential eye contact, irritation or injury. Depending on conditions of use, a face shield may be necessary.Skin: The use of gloves impervious to the specific material handled is advised to prevent skin contact. Users should check with manufacturers to confirm the breakthrough performance of their products. Depending on exposure and use conditions, additional protection may be necessary to prevent skin contact including use of items such as chemical resistant boots, aprons, arm covers, hoods, coveralls or encapsulated suits. Suggested protective materials: butyl and nitrile rubbers.Respiratory Protection: Where there is potential for airborne exposure above the exposure limits,a NIOSH approved air purifying respirator with an organic vapor cartridge may be used.A respiratory protection program that meets OSHA's 29 CFR 1910.134 and ANSI Z88.2requirements must be followed whenever workplace conditions warrant a respirator's use. Air- purifying respirators provide limited protection and cannot be used in atmospheres that exceed the maximum use concentration as directed by regulation or the manufacturer’s instructions, in oxygen deficient (less than 19.5% oxygen) situations or under conditions that are immediately dangerous to life and health (IDLH).Use a positive pressure air supplied respirator if there is potential for uncontrolled release, exposure levels are unknown, or any other circumstances where air-purifying respirators may not provide adequate protection.Other Protective Equipment: Eye wash and quick-drench shower facilities should be available in the work area. Thoroughly clean shoes and wash contaminated clothing before reuse.Suggestions provided in this section for exposure control and specific types of protectiv e equipment are based on readily available information. Users should consult with the specific manufacturer to confirm the performance of their protective equipment. Specific situations may require consultation with industrial hygiene, safety, or engineering professionals.9. PHYSICAL AND CHEMICAL PROPERTIES (approximate v a lues)Appearance: Clear, blue liquidOdor: Mild alcoholOdor threshold: 4.2-596 ppmpH: Not applicableMelting/Freezing Point: -97.8˚C /208˚FBoiling point (at 1 atm): 64.7˚C / 148 ˚FFlash Point: 35 ˚C / 9 ˚F (Closed Cup)Auto-Ignition Temperature: 470 ˚C / 878 ˚FEvaporation rate (butyl acetate = 1): 4.1Flammability (solid, gas): Not applicableExplosive Limits: Lower – 6%/ Upper – 36%Vapor Pressure: 92 mmHg @ 20 ˚C / 68 ˚FProduct #(s) – 4105Vapor Density (air = 1): 1.1 @ 15 ˚C / 59 ˚FSpecific gravity (H20 = 1): 0.79 @ 20˚C / 68 ˚FSolubility in water: SolublePartition Coefficient: n-octanol/water: Log P = -0.77Decomposition Temperature: No dataViscosity: 5.81 x 10-7 m2/s @ 40 ˚C / 104 ˚F10. STABILITY AND REACTIVITYStability (thermal, light, etc.): Stable under normal conditions of storage and handling.Conditions to Avoid: Avoid all possible sources of ignition (see Sections 5 and 7).Incompatibility (materials to avoid): Avoid contact with strong acids, bases and oxidizers such as liquid chlorine and oxygen. Contact with these materials may cause a violent or explosive reaction.May be corrosive to lead, aluminum, magnesium and platinum. May react with metallic aluminum or magnesium and generate hydrogen gas. May attack some forms of plastic, rubber and coatings.Hazardous Decomposition Products: Thermal decomposition may release carbon monoxide, carbon dioxide, and formaldehyde.Hazardous Polymerization: Will not occur.11. TOXICOLOGICAL INFORMATIONAcute Toxicity:Product/Ingredient Name Result Species DoseMethanol (major ingredient) LD50 OralLD50 DermalLC50 Inhalation (vapor) RatRabbitRat>2528 mg/kg17,100 mg/kg13.3 mg/l – 6hrNote: Assigned to classification based on human experience and not animal data.Skin Corrosion/Irritation: Causes mild irritation. Repeated exposure may cause dryness orcracking.Serious Eye Damage/Irritation: Causes mild irritation.Signs and Symptoms: High concentrations can cause minor respiratory irritation, headache,drowsiness, dizziness, loss of coordination, disorientation and fatigue. Ingestion can causeirritation of the digestive tract, nausea, abdominal pain, vomiting and visual disturbances ranging from blurred vision to light sensitivity, blindness or death.Skin Sensitization: None reportedRespiratory Sensitization: None reportedGerm Cell Mutagenicity: There is insufficient information available to conclude that methanol is mutagenic.Carcinogenicity: Methanol did not demonstrate carcinogenic effects in rats and mice treated via whole body inhalation at concentrations > 1.3 mg/l in air. There is insufficient informationavailable to conclude that methanol is carcinogenic. It is not listed by NTP, IARC or OSHA.Product #(s) – 4105Reproductive Toxicity: Methanol has produced fetotoxicity in rats and teratogenicity in miceexposed by inhalation to high concentrations of methanol vapors.Specific Target Organ Toxicity (Single Exposure): Methanol ingestion causes damage to the optic nerve causing blindness. May cause drowsiness and dizziness.Specific Target Organ Toxicity (Repeated Exposure): There is insufficient informationavailable to conclude that methanol causes target organ effects from repeated exposure.Aspiration Hazard: May be fatal if swallowed and enters airways.12. ECOLOGICAL INFORMATIONToxicity:Ingredient Name Result Species ExposureMethanol (major ingredient) Acute EC50 = 16.912 mg/L Marine WaterAcute LC50 = 2500000 ug/L Marine WaterAcute LC50 = 3289 mg/L Fresh WaterAcute LC50 > 100000 ug/L Fresh WaterAlgaeCrustaceansDaphniaFish96 hours48 hours48 hours96 hoursPersistence and Degradability: Methanol biodegrades easily in water and soil.BOD5 = 1.1COD = 1.05 – 1.55, 99%Bioaccumulative Potential: Risk of bioaccumulation is low (BCF <500 and low log K ow <4). BCF =0.2 - <10 Log K ow = -0.77Mobility in Soil: Methanol is highly mobile. Adsorption coefficient (K oc) solid phase/liquid phase = 1 Other Adverse Effects: None known13. DISPOSAL CONSIDERATIONSThe generator of a waste is always responsible for making proper hazardous waste determinations and needs to consider state and local requirements in addition to federal regulations.Recycle wherever possible. Large volumes may be suitable for re-distillation or, if contaminated, incinerated. Can be disposed of in a sewage treatment facility.This material, if discarded as produced, would not be a federally regulated RCRA “listed” hazardous waste. However, it would likely be identified as a federally regulated RCRA hazardous waste for the following characteristic of ignitability (D001). See Sections 7 and 8 for information on handling,storage and personal protection and Section 9 for physical/chemical properties. It is possible that the material as produced contains constituents which are not required to be listed in the MSDS but could affect the hazardous waste determination. Additionally, use which results in chemical orphysical change of this material could subject it to regulation as a hazardous waste.14. TRANSPORT INFORMATIONDOT/TDG Proper Shipping Name: Flammable Liquid n.o.s. (Methanol)Product #(s) – 4105DOT/TDG Identification Number: UN1993DOT Hazard Class: 3 / TDG Hazard Class: 3(6.1)DOT/TDG Packing Group: IIERG Guide Number: 131Marine Pollutant: No15. REGULATORY INFORMATIONTSCA: Methanol is listed on the TSCA inventory.DSL: Methanol is listed on the DSL inventory.OSHA (Occupational Safety and Health Administration): This material is considered to be hazardous as defined by the OSHA Hazard Communication Standard.This material has not been identified as a carcinogen by NTP, IARC or OSHACERCLA/SARA – Section 302 Extremely Hazardous Substances and TPQ (in pounds): This material does NOT contain chemicals subject to the reporting requirements of SARA 302 and 40 CFR 355 Appendix A and B.EPA (CERCLA) Reportable Quantity (in pounds): This material contains the following chemicals subject to the reporting requirements of 40 CFR 302.4.Component Concentration RQMethanol 22-36% 500 lbs CERCLA/SARA - Sections 311/312 (Title III Hazard Categories):Acute: Yes Chronic: Yes Fire: Yes Reactivity: NoCERCLA/SARA – Section 313 and 40 CFR 372: This material contains the following chemicals subject to the reporting requirements of SARA 313 and SARA Title III and 40 CFR:Component Concentration de minimisMethanol 22-36% 1% California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material contains detectable chemicals known to the State of California to cause cancer and/or reproductive toxicity.Component Concentration EffectMethanol 22-36% Developmental Canada:This product has been classified in accordance with the hazard criteria of the Controlled Products Regulations (CPR) and the SDS contains all the information required by the Regulations.WHMIS Hazard Class: B2, D1B, D2A, D2B16. OTHER INFORMATIONIssue Date: May 2, 2013Previous Issue Date: May 2, 2013Change: Updated to new GHS compliant HCS 2012 criteriaProduct #(s) – 4105DISCLAIMER OF EXPRESSED AND IMPLIED WARRANTIESThe information in this document is believed to be correct as of the date issued. HOWEVER, NO WARRANTY OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR ANY OTHER WARRANTY IS EXPRESSED OR IS TO BE IMPLIED REGARDING THE ACCURACY OR COMPLETENESS OF THIS INFORMATION, THE RESULTS TO BE OBTAINED FROM THE USE OF THIS INFORMATION OR THE PRODUCT, THE SAFETY OF THIS PRODUCT, OR THEHAZARDS RELATED TO ITS USE. This information and product are furnished on the condition that the person receiving them shall make his own determination as to the suitability of the product for this particular purpose and on the condition that he assumes the risk of his use thereof.。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
一、产品概述：
乳胶漆防腐剂DL-T203是一种高效、广谱绿色防腐剂,对抑制革兰氏阳性菌,革兰氏阴性菌及其他细菌的生长有较好的效果。
在使用浓度条件下与乳液配伍性好，与水、低分子醇混溶、操作简单。
是一种低毒、广谱型杀菌剂，对还原菌、淤泥成型菌、铁氧化菌、霉菌等有很强的杀灭作用。
乳胶漆防腐剂DL-T203杀菌防霉灭藻效果广谱长效，不产生抗药性。
不含重金属。
乳胶漆防腐剂DL-T203广泛地应用于在乳胶漆、涂料、油漆、高分子合成乳液等水性体系中。
二、技术指标：
项目指标
外观浅黄色透明液体
密度(20℃)g/cm3 1.05～1.15
溶解性与水完全混溶
有效含量%15
PH 值 3.0～5.0
三、产品用途：
乳胶漆防腐剂DL-T203广泛用于内外墙水性涂料、乳胶漆、丙烯酸乳液、醋酸乳液、聚丙乳液、大白等水性体系中杀菌防腐。
四、使用方法：
根据生产环境的菌落数、季节气候条件、水源、原料等情况适当调整添加量，一般使用浓度为1-3‰，实际添加量请用专业微生物试验得出。
如需杀菌抑菌同时作用，用量按以上用量加倍小试后而定增减。
五、包装储存：
乳胶漆杀菌防腐剂DL-T203采用25kg塑料桶包装，也可根据用户要求包装。
储存在阴凉避光处，保质期为一年。
六、注意事项：
1.本品属于Ⅱ类腐蚀性化学品，使用时要带防护眼镜和防酸手套，一旦溅到皮肤上，要用大量清水冲洗。
2.适于在pH<8.5的介质中使用或配伍。
3.避免加入硫化物，不可与氧化，还原性物质接触。
七：运输：非危险品,适合常规运输。