BELL CLSM-100LA电流传感器说明书
巴哈拉克IAM-100气体监测器说明书
Economical Standalone or System Wide MonitoringG a s D e t e c t o r /M o n i t o r1-800-736-4666 | 724-334-5000 | w w w.M y B a c h a r a c h.c o m | h e l p @M y B a c h a r a c h.c o mFeatures & Benefits:Real-time continuous gas detection that’s scalable, reliable and affordableIdeal for commercial applications such as hotel rooms, apartments, dorms, hospitals,restaurant kitchens or battery charging rooms Detects refrigerants (at ≥1,000 or ≥10,000 ppm),TVOCs (at ≥1,000 ppm), combustible gases and hydrocarbons (at ≥5,000 ppm)Fast-responding, long-life sensors Integrated visual LED and audible alarms Two onboard relays to activate shut-off valves,exhaust fans, or connect to a BMS or fire panel Remote sensor with aesthetic faceplate available fordiscreet monitoring in decorative interiorsI A M w 100Optional IAM-ControllerIAM-100 Standard HousingRemote sensor aesthetic faceplate(brushed steel finish)The IAM-100 Gas Monitor from Bacharach offers exceptional continuos monitoring performance and flexibility at an economical price. By itself, or integrated into a comprehensive detection system, the IAM-100 is a scalable solution for detecting a variety of refrigerants, combustible gases and VOC gas leaks at the lowest possible cost.Onboard LEDs illuminate when the sensor is in an alarm state while the unit’s audible alarm alerts personnel in the area that levels have exceeded the desired limit. The audible alarm can be muted with the onboard silence switch. Integrated dual relays enable the IAM-100 to shut-off refrigerant or propane supply lines while the second relay can be used as a connection to a building BMS or BAS system.The IAM-100 is an alarm threshold device. When the range of the sensor is exceeded, the detector will go into alarm. For example, a unit with a 1,000 ppm R-410a sensor will activate its alarm when the detected refrigerant meets or exceeds 1,000 ppm.©2014, Bacharach, Inc., all rights reserved. All information is subject to verification.January 2014 - REV. 0 Printed in U.S.A.BACHARACH IS A U.S.BASED MANUFACTURERDistributed By:IAM-100 Technical Specifications110 VAC/60 Hz or 220 VAC/50 Hz; 11W max.Green LED Red LEDInternal buzzer (with onboard mute button)Yes: (Red LED On, Green LED Off, Siren Off)2 Relays:each rated 1 Amp @ 24 VDCSelectable: 0, 5, 10 or 15 minutes IP30Semiconductor (multi-gas) / 5-8 year life -4º to 122ºF -20º to 50ºC0-95% Non-condensingAnnual test or calibration recommended.Refer to manual for sensor specific instructions 5 mins. initiallyCE • IEC/EN 61010 • UL/CSA 61010-15.8”x 3.47”x 2.44” • 1lb. 6oz.147 x 88 x 62mm • 633gPower Supply:Power Monitoring:Visual Alarm:Audible Alarm:Fault Monitoring:Relays:Alarm Delay:IP Rating:Sensor Type / Life:Temperature Range:Humidity Range:Calibration:Warm-up Delay:Approvals:Dimensions & Weight:(enclosure types)IAM-Controller Technical Specifications110 VAC/60 Hz or 220 VAC/50 Hz; 11W max.Green LED Red LEDExternal buzzer (with onboard mute button)Yes: (Red LED On, Green LED Off, Siren Off)2 Relays:each rated 10 Amp @ 110/220 VAC IP51300 m (984 ft.);16-24 AWGCE • UL/CSA 61010Standard 10.3”x 10.4”x 3.3”• 5lb. 12oz.IP30 262 x 265 x 84mm • 2.6kgPower Supply:Power Monitoring:Visual Alarm:Audible Alarm:Fault Monitoring:Relays:IP Rating:Max Cable Distance:(controller - transmitter)Approvals:Dimensions & Weight:(enclosure types)IAM-100 Ordering InformationIAM-100 Common ConfigurationsR-410a | 1,000 ppm • Standard Housing • 110 VAC powered R-410a | 10,000 ppm • Standard Housing • 110 VAC powered R-410a | 1,000 ppm • Remote w/faceplate • 110 VAC powered R-410a | 10,000 ppm • Remote w/faceplate • 110 VAC powered R-410a | 1,000 ppm • Standard Housing • 220 VAC powered R-410a | 10,000 ppm • Standard Housing • 220 VAC powered R-410a | 1,000 ppm • Remote w/faceplate • 220 VAC powered R-410a | 10,000 ppm • Remote w/faceplate • 220 VAC powered R-404a | 1,000 ppm • Standard Housing • 110 VAC powered R-290 | 5,000 ppm • Standard Housing • 110 VAC powered R-134a | 1,000 ppm • Standard Housing • 110 VAC powered R-407a | 1,000 ppm • Standard Housing • 110 VAC powered CH 4 | 5,000 ppm • Remote w/faceplate • 110 VAC powered H 2 | 5,000 ppm • Remote w/faceplate • 110 VAC powered Ethylene| 5,000 ppm • Remote w/faceplate • 110 VAC powered VOC | 1,000 ppm • Remote w/faceplate • 110 VAC powered LPG | 5,000 ppm • Remote w/faceplate • 110 VAC powered CH 4 | 5,000 ppm • Remote w/faceplate • 220 VAC powered H 2 | 5,000 ppm • Remote w/faceplate • 220 VAC powered Ethylene| 5,000 ppm • Remote w/faceplate • 220 VAC powered VOC | 1,000 ppm • Remote w/faceplate • 220 VAC powered LPG | 5,000 ppm • Remote w/faceplate • 220 VAC powered6201-11076201-11436201-51076201-51436202-11076202-11436202-51076202-51436201-11036201-11136201-11016201-11056201-51146201-51196201-51206201-51216201-51516202-51146202-51196202-51206202-51216202-5151IAM-Controller Ordering InformationIAM-Controller Options110 VAC powered 220 VAC powered6700-01006700-0101IAM-100 Gas Types & Detection RangesSemiconductor Sensor - Threshold RangesRefrigerants: HFCs: including R-134a, R-410a, R-404a, R-507, R-407HCFCs: including R-22 CFCs:including R-11Hydrocarbons:including Methane, Natural Gas, Propane Butane, LPG, Hydrogen Isobutane VOCs:including Acetone, Chloroform, Ethanol, Methanol, Methyl and Methylene Chloride, Ethyl and Ethylene Chlorideat ≥1,000 ppm or at ≥10,000 ppm at ≥1,000 ppm or at ≥10,000 ppm at ≥1,000 ppm or at ≥10,000 ppm at ≥5,000 ppmat ≥1,000 ppm。
Honeywell CSDA CSDC系列开关型电流传感器 说明书
Honeywell/Commercial Switch&Sensor 霍尼韦尔商业开关与传感器上海：Tel:021-******** 北京：Tel:010-******** 深圳：Tel:0755-******** 广州：Tel:020-******** e-mail:jian.bo.zhou@ /sensing反应时间µs100100100100100100100100100100100100特点：●数字电平输出● 测量交流、直流电流超● 穿孔式设计●快速反应时间（100µS ）● 输出输入隔离● 最小的电流损耗● 最大测量电流只决定于导体的大小● 高精度、低成本的测量● 工作温度范围：-25—85℃数字电流传感器CS 系列数字电流传感器当被测电流超过动作点，输出电平从大约Vcc 电平降到0.4V （除了CSDB1CC 型号从0.4V 上升Vcc ）。
传感器可测量直流或交流电流，但当测量交流电流时，输出将在每一个过零点关断。
型号CSDA1BA CSDA1BC CSDC1BA CSDC1BC CSDA1AA CSDA1AC CSDC1AA CSDC1AC CSDC1DA CSDA1DA CSDC1DC CSDA1DC订货指南——电流沉输出动作电流@25℃（安培—匝数）（最小值）.0.322.20.322.20.322.20.322.20.320.322.22.2（最大值）.0.886.50.886.50.886.50.886.50.880.886.56.5释放电流25℃-85℃（安培—匝数）0.080.600.080.600.800.600.800.600.080.080.600.60供电电压（VDC ）6-166-165±0.25±0.26-166-165±0.25±0.25±0.26-165±0.26-16输出电压（V ）0.40.40.40.40.40.40.40.40.40.40.40.4输出电流（mA ）沉输出20mA 20mA 20mA 20mA 20mA 20mA 20mA 20mA 20mA 20mA 20mA 20mA引脚方式222211113333动作电流25℃-85℃（安培—匝数）0.25-1.01.7-7.50.25-1.01.7-7.50.25-1.01.7-7.50.25-1.01.7-7.50.25-1.00.25-1.01.7-7.51.7-7.5Mom.0.503.50.503.50.503.50.503.50.500.503.53.5。
CSA502-P044T01S 电流传感器使用说明书
CSA502-P044T01S 电流传感器使用说明书V1.4本手册为湖南银河电气有限公司产品CSA502-P044T01S电流传感器用户手册，本手册为用户提供安装调试、操作使用及日常维护的有关注意事项，在安装、使用前请仔细阅读。
本手册随产品一起提供，请妥善保管、以备查阅和维护使用。
声明我们非常认真的整理此手册，但我们对本手册的内容不保证完全正确。
因为我们的产品一直在持续的改良及更新，故我方保留随时修改本手册的内容而不另行通知的权利。
同时我们对不正确使用本手册所包含内容而导致的直接、间接、有意、无意的损坏及隐患概不负责。
安全操作知识◆产品使用前，请您务必仔细阅读用户手册。
◆需对产品进行搬动时，请您务必先断电并将与之相连的所有连接线缆等拔掉。
◆如果发现机壳、稳固件、电源线、连接线缆，或相连的设备有任何损坏，请您立即将装置与电源断开。
◆如果对设备的安全运行存在疑虑，应立即关闭设备和相应附件，并在最快时间内与本公司技术支持部门取得联系，沟通解决。
！安全警示 电流传感器不允许开路使用，即母线有电流或传感器已上电的状态下，都不允许断开输出端；仅母线无电流且传感器未上电的状态下，才可以断开传感器的电流输出端或主机与探头的连接,否则有感应高压，发生电击的危险！1. 产品概述CSA502-P044T01S 一种能在原边、副边完全隔离条件下测量直流、交流、脉冲以及各种不规则波形的电流传感器，它主要用于要求准确度高的计量检定和计量校准领域，以及要求高灵敏度、高稳定性和高可靠性的电能质量分析、功率分析仪、医疗、航空航天、导弹、舰艇等领域。
2. 技术特点● 极高的准确度 ● 极好的线性度 ● 极高的稳定性 ● 极高的灵敏度 ● 极高的分辨率 ● 极低的温度漂移 ● 极低的失调电流● 极低的插入损耗 ● 抗干扰能力强 ● 响应速度快 ● 极低的噪声 ● 极小的角差 ● 宽频带 ● 模拟量输出 3. 应用场合● 计量检定与校准 ● 实验室电流测量● 仪器仪表（如功率分析仪） ● 医疗设备（如核磁共振MRI ） ● 电池组检测 ● 电力控制 ● 电源 ● 舰船 ● 新能源 ● 轨道交通 ● 航空航天 ● 工业测量4. 电气性能项目符号测试条件数值单位最小标称最大原边额定电流 I PN -- -- ±5000 -- Adc 测量范围 I PM 1分钟/小时 -- -- ±6000 Adc 工作电压 V c 全范围 90 220 260 Vac 电源消耗 I PM 范围内 -- 150 -- W 电流变比 K N 输入：输出 5000:1 --额定输出电流 I SN 原边额定电流-- ±1 -- A测量电阻R M0 -- 1 Ω5. 精度-动态参数项目符号测试条件数值单位最小标称最大精度 X e 输入直流，25±10℃ -- -- 10 ppm 比差误差 X Ge 输入交流50Hz/60Hz ，25±10℃-- -- 100 ppm 角度误差 X Pe -- -- 0.01 crad线性度εL-- -- -- 2 ppm温度漂移系数 TCI OUT -- -- -- 0.1 ppm/K时间漂移系数 TT -- -- -- 0.2 ppm/month供电抗干扰 TV -- -- -- 1 ppm/V 零点失调电流 I o 25±10℃ -- -- 2 ppm 零点失调电流 I oT 全工作温度范围内-- -- ±10 ppm纹波电流 I n DC-10Hz -- -- 0.5 ppm 动态响应时间 t r di/dt=100A/us 上升至90% I PN-- -- 1us电流跟随速度 di/dt -- 200 -- -- A/us 频带宽度(- 3 dB)F-- 0 -- 20 kHz6. 一般特性项目符号测试条件数值单位最小标称最大工作温度范围 T A -- -10 -- +70 ℃ 存储温度范围T S-- -25 -- +85 ℃电流探头检测信号 -- 正常工作时，红色探头检测灯常亮，DB9插座第4脚和第9脚处于无信号输出的开路状态。
Sensata Technologies 电流传感器产品说明书
1-DCL | SERIESFeatures• R atings from 7 A to 40 A @ 200 VDC and from7 A to 10 A @ 500VDC • Mosfet Output• UL Approved, CE Compliant to EN60950-1• Improved SEMS screw and washer• Redesigned housing with anti-rotation barriers • DC control• EMC Compliant to Level 3• Epoxy Free DesignPRODUCT SELECTIONOUTPUT SPECIFICATIONS 2INPUT SPECIFICATIONS2GENERAL SPECIFICATIONS 2WIRING DIAGRAM*Inductive loads must be diode suppressed.EQUIVALENT CIRCUIT BLOCK DIAGRAMS-DC +DC-DC+DCInput Current vs Input Voltage Standard Regulated “DC” InputsI n p u t C u r r e n t (m A )DC Input VoltageMECHANICAL SPECIFICATIONS2(2 places)Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters]Screw TerminationHex Standoff Termination (“K” Option) 1S u r g e C u r r e n t (A m p )Surge Duration (msec )D2D07LS u r g eC u r r e n t (A m p )Surge Duration (msec )D2D40LS u r g e C u r r e n t (A m p )Surge Duration (msec )D4D12LS u r g e C u r r e n t (A m p )D5D10LS u r g e C u r r e n t (A m p )Surge Duration (msec )D1D40LS u r g e C u r r e n t (A m p )Surge Duration (msec )S u r g e C u r r e n t (A m p )Surge Duration (msec )D1D20LS u r g e C u r r e n t (A m p )Surge Duration (msec )Duty Factor 10%Duty Factor 20%Duty Factor 50%For Pulse Wide Modulation applications selectthe curve according duty factor and pulse duration as following.(i) for Single Surge Pulse Tc=40°C ;Tj 175°C(ii) for Repetitive Surge Pulse Tc=40°C ;Tj 130°CDuty Factor=Pulse Wide Periodx100 (%)S u r g e C u r r e n t (A m p )Surge Duration (msec )D2D12LS u r g e C u r r e n t (A m p )Surge Duration (msec )D4D07LS u r g e C u r r e n t (A m p )Surge Duration (msec )D5D07L(iii) SSR metal base plate acting as heat sink, it must be exposed to free ambient air.Ambient Temperature (ºC)D1D07L5°C/WNo Heat Sink(iii)D1D12L3°C/W5°C/WNo Heat Sink(iii)Ambient Temperature (ºC)D1D20L2°C/W3°C/WNo Heat Sink(iii)Ambient Temperature (ºC)D1D40L1°C/W3°C/W5°C/WAmbient Temperature (ºC)D2D07L3°C/W5°C/WNo Heat Sink(iii)Ambient Temperature (ºC)D2D12L3°C/W5°C/WNo Heat Sink(iii)Ambient Temperature (ºC)D2D40L0.7°C/W1.5°C/W5°C/WAmbient Temperature (ºC)D4D12L1°C/W2°C/W5ºC/WAmbient Temperature (ºC)D4D07L2°C/W3°C/WNo Heat Sink(iii)Ambient Temperature (ºC)D5D07L1°C/W3°C/W5ºC/WAmbient Temperature (ºC)D5D10LAmbient Temperature (ºC)0.7°C/W2°C/W5°C/WACCESSORIESAVAILABLE OPTIONSNot all part number combinations are available.Contact Crydom Technical Support for information on the availability of a specific part number. Array * Required for valid part number**For options only and not required for valid part numberPage 8CONTACT USAmericas+1 (877) 502 5500************************Europe, Middle East & Africa +44 (1202) 416170***********************Asia Pacific*************************.com China +86 (21) 2306 1500Japan +81 (45) 277 7117Korea +82 (31) 601 2004India +91 (80) 67920890Rest of Asia +886 (2) 27602006 ext 2808Sensata Technologies, Inc. (“Sensata”) data sheets are solely intended to assist designers (“Buyers”) who are developing systems that incorporate Sensata products (also referred to herein as “components”). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, evaluation and judgment in designing Buyer’s systems and products. Sensata data sheets have been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements, improvements and other changes to its data sheets or components without notice.Buyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEVER, NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATA SHEETS ARE PROVIDED “AS IS”. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATA SHEETS OR USE OF THE DATA SHEETS, EXPRESS, IMPLIED OR STATUTORY, INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD TO SENSATA DATA SHEETS OR USE THEREOF.All products are sold subject to Sensata’s terms and conditions of sale supplied at SENSATA ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS’ PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, WARNINGS(1)Option “K” is designed and tested for use with printed circuit boards or ring/fork terminals having a thickness between 0.031 and 0.093 inches (0.79 to 2.36 mm).(2)All parameters at Tc=25°C unless otherwise specified.(3)Heat sinking required, see derating curves. (4)Low current loads and high ambient temperature can affect turn-on time.(5)8VDC Minimum control voltage. Resistive loads only. Consider switching losses; at maximum frequency reduce to 75% output current.(6)Increase minimum voltage by 1V for operations from -20 to -40°C.(7)Decrease maximum control voltage 1.35V/°C above 80°C ambient temperature.(8) A ll parameters at 50% power rating and 100% duty cycle (contact Crydom tech support for detailed report).For additional information or specific questions, contact Crydom Technical SupportGENERAL NOTESAGENCY APPROVALS & CERTIFICATIONSEN60950-1: Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7:IEC 61000-4-2 Electrostatic Discharge Level 3IEC 61000-4-4 Electrically Fast Transients Level 3IEC 61000-4-5 Electrical Surges Level 3E116950RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE• The product’s side panels may be hot, allow the product to cool before touching • Follow proper mounting instructions including torque values • Do not allow liquids or foreign objects to enter this productFailure to follow these instructions can result in serious injury, or equipment damage.HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH• Disconnect all power before installing or working with this equipment • Verify all connections and replace all covers before turning on powerFailure to follow these instructions will result in death or serious injury.。
LEM LT208-S7 直流、交流和脉冲电流传感器说明书
Page 1/3电流传感器 LT 208-S7原边和副边之间是绝缘的，用于测量直流、交流和脉冲电流。
电参数I PN原边额定有效值电流 200AI PM 原边电流, 测量范围 0 .. ± 300AR M 测量电阻R M min R M max with ± 12 V @ ± 200 A max 0 50 Ω@ ± 300 A max 0 26 Ω with ± 15 V @ ± 200 A max 0 73 Ω @ ± 300 A max0 40ΩI SN 副边额定有效值电流 100 mA K N 转换率1 : 2000V C 电源电压 (± 5 %) ± 12 .. 15 V I C电流消耗28 (@ ± 12V) + I S mA精度 - 动态参数X G总精度 @ I PN , T A = 25°C ± 0.5 %εL线性度 < 0.1 %Typ Max I O 零点失调电压 @ I P = 0, T A = 25°C± 0.20 mA I OM 磁性失调电流 1) @ I P = 0, 通过 3 x I PN 的过载 ± 0.20 mA I OT I O 的温漂 (- 10°C .. + 70°C) ± 0.20 ± 0.64 mA t ra 反应时间 to 10 % of I PN < 500 ns t r 响应时间 2) to 90 % of I PN < 1 µs di/dt di/dt 跟随精度 > 100 A/µs BW频带宽度 (- 3 dB)DC .. 100kHz一般参数T A环境操作温度 - 10 .. + 70 °C T S 环境贮存温度- 25 .. + 80 °C R S 副边线圈电阻 @ T A = 70°C 21 Ωm 质量 79g标准3)EN 50178注释1)磁场的强磁力的结果 2)100 A/µs 的 di/dt3)备有相应的检测清单I PN = 200 A 性能应用霍尔原理的闭环(补偿)电流 ●传感器符合 ●UL 94-V0 标准的绝缘外壳优势出色的精度 ●良好的线性度 ●低温漂 ●最佳的反应时间 ●宽频带 ●无插入损失 ●抗干扰能力强 ●电流过载能力●应用交流变频调速、伺服电机 ●直流电机牵引的静电转换 ●电池电源 ●不间断电源 ●(UPS)开关电源 ●(SMPS)电焊机电源 ●应用领域工业●用霍尔原理的闭环(补偿)电流传感器•符合 UL 94-V0标准的绝缘外壳优势•出色的精度•良好的线性度•低温漂•最佳的反应时间•宽频带•无插入损失•抗干扰能力强•电流过载能力应用•交流变频调速伺服电机•直流电机牵引的静电转换•电池电源•不间断电源 (UPS)•开关电源 (SMPS)•电焊机电源I PN =50 APage 2/3电流传感器 LT 208-S7电隔离性能V d 交流隔离耐压测试有效值 1) , 50 Hz, 1 分钟 3.52kV V w 瞬态耐压 1.2/50 µs 6.5 kVMin dCp 爬电距离 2)10 mm dCI 电气间隙距离 2) 6mmCTI比较路经指数 (group IIIa)275应用参考依据 EN 50178 及 IEC 61010-1 标准,应用条件示范如下:负载电压类别: ●OV 3污染等级: ●PD2非特殊应用领域●注释 1)原副边之间2)原边至外壳表面端子安全事项传感器必须按照使用说明要求安放在符合应用标准和安全要求的电子或电气设备中.注意,小心电击传感器工作时,某些部位可能会承受危险电压(如原边母排,电源)忽视这些将导致损坏和严重危险. 传感器是内置式设备,在安装完毕后其导电部分一定要保证不被外界触及. 可采用保护壳或附加屏蔽铠装. 主电源必须能被断开.EN 50178IEC 61010-1dCp, dCI,额定耐压值额定电压单绝缘600 V 600 V 加强型绝缘300 V300 VV wPage 3/3说明I ●S 在 I P 按箭头方向流动时, 是正向的.原边导体温度不超过 ●100°C.母排完全充满原边穿孔时动态表现 ● (di/dt 和响应时间)为最佳.此模块为标准传感器. 对于不同的应用 ● (电源电压、匝比, 单项测量...）请与我们联系.机械性能自然公差 ● ± 0.5 mm紧固点 ● 2 孔 ∅ 5.4 mm 原边穿孔 ● ∅ 20 mm副边连接 ● 插座 2541 WV-4P（上海嘉仁）LT 208-S7外形尺寸 (in mm)。
电流传感器 BLF-S5系列 说明书
电流传感器B LF-S5系列
用于测量直、交流及脉冲电流副边之间高度绝缘。
电参数
BLF100-S5 BLF200-S5 BLF300-S5 I
原边额定电流100200300A PN
I
原边电流测量范围200400600A P
V
副边额定电压4V S N
Vc 电源电压± 12....15(±5%)V Ic 电流消耗35mA 绝缘测试交流电压有效值 50 Hz, 1 分钟 2.5K V V
d
精度－动态性能参数
X精度I
%
pn
ε线性度
0.5
10-3 / ℃V
S N
增益值<
尺寸 (单位:mm, 1 mm = 0.0394 英寸)
注意
• 当原边电流沿传感器箭头方向流动时，在输出端M 获得同相电压•原边母排温度不得超过100°C
• 原边母排充满孔径时，可获得最佳动态特性
• 原边额定电流值I PN 及副边额定电压V SN 可由用户指定生产
机械参数
•
常规误差± 0.2 mm •原边穿孔34 x 11 mm •副边连接MOLE X 5045−4•
安装
中心孔∅7
连接
１２．．．１５Ｖ２． 。
CrossChip Microsystems CC6904 单芯片霍尔效应电流传感器说明书
CC6904单芯片霍尔效应电流传感器5A/10A/20A/30A 系列概述CC6904是一款高性能单端输出的线性电流传感器，可以更为有效的为交流（AC ）或者直流（DC ）电流检测方案，广泛应用于工业，消费类及通信类设备。
CC6904内部集成了一颗高精度，低噪声的线性霍尔电路和一根低阻抗的主电流导线。
当采样电流流经主电流导线，其产生的磁场在霍尔电路上感应出相应的电信号，经过信号处理电路输出电压信号，使得产品更易于使用。
线性霍尔电路采用先进的BiCMOS 制程生产，包含了高灵敏度霍尔传感器，霍尔信号预放大器，高精度的霍尔温度补偿单元，振荡器，动态失调消除电路和放大器输出模块。
在无磁场的情况下，静态输出为50%VCC 。
在电源电压3.3V 条件下，OUT 可以在0.2~3.1V 之间随磁场线性变化，线性度可达0.4%。
CC6904内部集成的动态失调消除电路使IC 的灵敏度不受外界压力和IC 封装应力的影响。
CC6904提供SOP8封装，工作温度范围-40~125°C 。
特性◆静态共模输出点为50%VCC ◆测量范围宽，5A/10A/20A/30A◆1MHz 斩波频率，高带宽，低噪声，单端模拟输出◆导线引脚到信号引脚有2000V 的安全隔离电压◆低功耗◆常温误差1%，全温误差3%◆温度稳定性好，内部采用了芯进专利的霍尔信号放大电路和温度补偿电路◆抗干扰能力强◆抗机械应力，磁参数不会因为受外界压力而偏移◆ESD (HBM)6000V应用◆电机控制◆负载监测系统◆开关电源◆过流故障保护功能框图订购信息产品名称灵敏度（CC6904SO-05A CC6904SO-10A CC6904SO-20A管脚定义12345678IP+IP+IP-IP-VCC OUT NCGNDSOP8封装极限参数推荐工作环境参数电源电压环境温度直流电流容量参数符号电气特性零电流输出温度系数ΔV OUT(Q)灵敏度温度系数ΔSens典型应用电路典型应用过流故障检测器电流峰值监测应用曲线&波形(若无特别指明，V CC =3.3V @25°C)V OUT vs.IP (正向电流上升沿响应)（20A ）V OUT vs.IP (正向电流下降沿响应)（20A ）V OUT vs.IP (负向电流上升沿响应)（20A ）V OUT vs.IP (负向电流下降沿沿响应)（20A ）CH2：OUT CH4：IPCH2：OUT CH4：IPCH2：OUT CH4：IPCH2：OUT CH4：IPt D 响应时间（20A ）静态电流vs.VCC 静态电流vs.Ta20A 系列V OUT(Q)vs.Ta(20A)V OUT vs.IP (20A)CH2：OUT CH4：IP468V OUT error vs.Ta(20A)Sens error vs.Ta(20A)封装信息SOP8封装注意:1.所有尺寸单位均为毫米。
MN 系列双极性电流电测仪说明书
DESCRIPTIONThe E3N clamp is designed to measure AC and DC currents by using Hall-effect technology. Its narrow, elongatedshape makes it ideal for measurements in cable bundles or in confi ned spaces such as the wiring on switchboards, motor control units and electrical circuits on motor vehicles. It is particularly appreciated for its True RMS measurements on AC+DC signals. It offers 2 different sensitivities.ELECTRICAL SPECIFICATIONS • Current range:0.1 A .. 10 A peak 0.5 A .. 100 A peak • Output signal:100 mV AC+DC / A AC+DC (1 V for 10 A)10 mV AC+DC / A AC+DC (1 V for 100 A)• Accuracy and phase shift (1):Calibre 10 A 100 ACurrent range100 mA .. 10 A peak 500 mA .. 40 A peak40 A .. 100 A peak% Accuracy of output signal ≤ 3 % + 5 mV ≤ 4 % + 500 µV≤ 15 %Phase shift≤ 1.5°≤ 1°≤ 1°• Bandwidth:DC .. 100 kHz (-3 dB) (depending on current value)• Rise/fall time from 10 % to 90 %:10 A calibre: 3 µs 100 A calibre: 4 µs • 10 % delay time:10 A calibre: 2,7 µs 100 A calibre: 1,8 µs• Insertion impedance (at 10 kHz / 50 kHz):< 1.3 mΩ / < 10 mΩ• DC zero adjustment:20 turns of potentiometer• Typical output noise level (peak-peak) from DC to 100 kHz:10 A calibre: 6 mV 100 A calibre: 600 µV • Battery:9 V alkaline (NEDA 1604A, IEC 6LR61)• Battery life: 55 hours typical • Typical consumption:8.6 mA typical / 12 mA max.• Battery level indicator:Green LED when > 6.5 V • Overload indication:Red LED indicates the measured current is too high for the selected range • Infl uence of temperature:≤ 2,000 ppm /°C• Infl uence of conductor position in jaws:≤ 0.5 % of output signal at 1 kHz• Common mode voltage (600 V max) forAC measurements (typical/max):10 A calibre:At 50 Hz: 3.48 mA/100 V / 5 mA/100 V At 400 Hz: 25.91 mA/100 V / 50 mA/100 V 100 A calibre: no measurementMECHANICAL SPECIFICATIONS • Clamping capacity:Cable: Ø max 11.8 mm • Output:Via 2 m coaxial cable terminated by BNC insulated plug• Dimensions: 231 x 67 x 36 mm • Weight:330 g with battery • Operating temperature:0° à +50°C• Storage temperature: -30 °C to +80 °C• Relative humidity for operation:0 to 85 % RH with a linear decrease above 35°C • Operating altitude: 0 to 2,000 m• Casing protection rating:IP20 (IEC 529)• Drop test:1 m (IEC 68-2-32)• Shock resistance:100 g / 6 ms / half-periode (IEC 68-2-27)• Vibration resistance:10/55/10 Hz, 0.15 mm (IEC 68-2-6)• Self-extinguishing capability: UL94 V2• Colour: Dark greySAFETY SPECIFICATIONS • Electrical safety:Instrument with double insulation or reinforced insulation between the primary the secondary and the grippable part located under the guard as per IEC 1010-1 & IEC 1010-2-032- 600 V category III, pollution degree 2- 300 V category IV, pollution degree 2• Electromagnetic compatibility (EMC):EN 50081-1: class B EN 50082-2:- Electrostatic discharge IEC 1000-4-2:4 kV level 2 performance criterion B8 kV in the air level 3 performance criterion B - Radiated field IEC 1000-4-3:10 V/m performance criterion A - Fast transients IEC 1000-4-4:1 kV level2 performance criterion B 2 kV level3 performance criterion B - Magnetic field at the network frequency (IEC 1000-4-8):field of 400 A/m at 50 Hz: < 1 ACurrent 10 A peak 100 A peak Output100 mV/A10 mV / ACURVES100 A calibreLinearity with DCFrequency responsePhase shiftImmunity regarding an external conductorLimitation of measurable current according to the frequencye r r o rp e a k c u r r e n t I pCurrent IpFrequencyFrequencyfrequencyMeasurement current: 1 A peakFrequencyMEASUREMENT CURRENT: 1 A PEAK––––Range: 100 mV/A ––°––Range: 10 mV /A–––– Conductor perpendicular to clamp ––°––conductor parallel to clamp–––– Range: 100 mV/A ––°––Range: 10 mV/ACURVES100 A calibre1 A peak2 A peak0.1 A peakInput signal:X: 2 ms/divY: 0.2 V/divClamp output signalX: 2 ms/divY: 200 mV/divInput signal:X: 5 ms/divY: 0.2 V/divClamp output signalX: 5 ms/divY: 200 mV/divInput signal:X: 5 ms/divY: 0.2 V/divClamp output signalX: 5 ms/divY: 200 mV/div Input signal:X: 1 ms/divY: 0.5 V/divClamp output signalX: 1 ms/divY: 50 mV/divInput signal:X: 0.1 ms/divY: 0.5 V/divClamp output signalX: 0.1 ms/divY: 50 mV/divInput signal:X: 20 µs/divY: 0.5 V/divClamp output signalX: 20 µs/divY: 50 mV/divInput signal:X: 20 µs /divY: 50 mV/divClamp output signalX: 20 µs/divY: 5 mV/divPinces ampèremetriques pour courant AC CURVES10 A calibre10 A peakInsertion impedancei n s e r t i o n i m p e d a n c e (m .o h m )Input signal:X: 0.1 ms/div Y: 0.5 V/div Clamp output signal X: 0.1 ms/div Y: 50 mV/divInput signal:X: 1 ms/div Y: 0.5 V/div Clamp output signal X: 1 ms/div Y: 50 mV/divInput signal:X: 10 µs/div Y: 0.5 V/div Clamp output signal X: 10 µs/div Y: 50 mV/div(1) Conditions of reference: 23 °C ± 5 °K, 20 % to 75 % RH, power supply voltage 8 V ± 0.1 V DC sinusoidal signal with frequency of DC to 1 kHz, external magnetic fi eld < 40 A/m, no DC components, no external conductor with circulating current, conductor centred for measurement, load impedance >1 MΩ / < 100 pF.Oscilloscope clamp for AC/DC current Model E3N (insulated AC/DC current probe)To orderReference AC/DC current clamp model E3N for oscilloscope, with battery and user’s manualP0*******A AC/DC current clamp model E3N for oscilloscope, with mains power, battery and user’s manualP0*******。
银河电气 CSA102-P041T01S 电流传感器使用说明书
CSA102-P041T01S 电流传感器使用说明书V1.1CSA102-P041T01S电流传感器使用说明书本手册为湖南银河电气有限公司产品CSA102-P041T01S电流传感器用户手册，本手册为用户提供安装调试、操作使用及日常维护的有关注意事项，在安装、使用前请仔细阅读。
本手册随产品一起提供，请妥善保管、以备查阅和维护使用。
声明我们非常认真的整理此手册，但我们对本手册的内容不保证完全正确。
因为我们的产品一直在持续的改良及更新，故我方保留随时修改本手册的内容而不另行通知的权利。
同时我们对不正确使用本手册所包含内容而导致的直接、间接、有意、无意的损坏及隐患概不负责。
安全操作知识◆产品使用前，请您务必仔细阅读用户手册。
◆需对产品进行搬动时，请您务必先断电并将与之相连的所有连接线缆等拔掉。
◆如果发现机壳、稳固件、电源线、连接线缆，或相连的设备有任何损坏，请您立即将装置与电源断开。
◆如果对设备的安全运行存在疑虑，应立即关闭设备和相应附件，并在最快时间内与本公司技术支持部门取得联系，沟通解决。
！安全警示 电流传感器不允许开路使用，即母线有电流或传感器已上电的状态下，都不允许断开输出端；仅母线无电流且传感器未上电的状态下，才可以断开传感器的电流输出端或主机与探头的连接,否则有感应高压，发生电击的危险！1.CSA102-P041T01S一种能在原边、副边完全隔离条件下测量直流、交流、脉冲以及各种不规则波形的电流传感器，它主要用于要求准确度高的计量检定和计量校准领域，以及要求高灵敏度、高稳定性和高可靠性的电能质量分析、功率分析仪、医疗、航空航天、导弹、舰艇等领域。
2.●极高的准确度●极好的线性度●极高的稳定性●极高的灵敏度●极高的分辨率●极低的温度漂移●极低的失调电流●极低的插入损耗●抗干扰能力强●响应速度快●极低的噪声●极小的角差●宽频带●模拟量输出3.●计量检定与校准●实验室电流测量●仪器仪表（如功率分析仪）●医疗设备（如核磁共振MRI）●电池组检测●电力控制●电源●舰船●新能源●轨道交通●航空航天●工业测量4.原边额定电流 I PN-- -- ±1000 -- Adc 测量范围 I PM1分钟/小时 -- -- ±120Adc 工作电压 V c全范围 90 220 260 Vac 电源消耗 I PM范围内 -- 100 -- W 电流变比 K N输入：输出 1000:1 -- 额定输出电流 I SN原边额定电流 -- ±1 -- A 测量电阻 R M0 -- 2 Ω5.精度 X e输入直流，25±10℃ -- -- 10 ppm比差误差 X Ge输入交流50Hz/60Hz，25±10℃ -- -- 100 ppm角度误差 X Pe-- -- 0.01 crad 线性度 εL-- -- -- 2 ppm温度漂移系数 TCI OUT-- -- -- 0.1 ppm/K 时间漂移系数 TT -- -- -- 0.2 ppm/month 供电抗干扰 TV -- -- -- 1 ppm/V 零点失调电流 I o25±10℃ -- -- 2 ppm 零点失调电流 I oT全工作温度范围内 -- -- ±10 ppm 纹波电流 I n DC-10Hz -- -- 0.5 ppm动态响应时间 t r di/dt=100A/us上升至90% I PN-- -- 1 us 电流跟随速度 di/dt -- 200 -- -- A/us 频带宽度(- 3 dB) F -- 0 -- 100 kHz 6. 一般特性项目符号测试条件数值单位最小标称最大工作温度范围 T A-- -10 -- +70 ℃ 存储温度范围 T S-- -25 -- +85 ℃电流探头检测信号 -- 正常工作时，红色探头检测灯常亮，DB9插座第4脚和第9脚处于无信号输出的开路状态。
电导率测量设备及传感器说明书
电极常数k = 0.1 cm –1应用在纯水和超纯水中测量：•离子交换器监测•反渗透•蒸馏•电除盐•制药行业中的WFI (注射用水)带温度探头的传感器与带自动温度补偿功能的电导率测量设备配套使用：•Liquiline CM442/CM444/CM448 (仅允许连接CLS16D)•Liquiline CM42•Liquiline CM14 (仅允许连接CLS16D)•Liquisys CLM223/253 (仅允许连接CLS16)•Mycom CLM153 (仅允许连接CLS16)使用上述变送器还可以进行电阻率测量(MΩ · cm)。
优势•得益于电极常数的精确出厂测定，确保了高测量精度•卫生型过程连接，可以安装在管道中或流通腔室中•带插头(IP68)或整体电缆(IP67)•电抛光表面，易清洗•蒸汽消毒时的最高温度为150 °C (302 °F)•质量证书中标识精确电极常数•通过EHEDG 认证(文档8)•通过美国药典Cl. VI 认证，第87和88章(可选)•EN 10204 3.1检测证书(可选)Memosens 技术优势•非接触式感应信号传输确保了最高过程安全性•采用数字式数据传输，确保了数据安全性•储存传感器特征参数，操作简便•传感器中记录传感器负荷参数，可实现预维护Products Solutions Services技术资料Condumax CLS16D/CLS16卫生型电导率传感器，模拟式传感器或Memosens 数字式传感器TI00227C/07/ZH/15.14Condumax CLS16D/CLS162Endress+Hauser功能与系统设计1电导式电导率测量原理示意图AC 交流电源I 电流表U 电压表测量系统完整的测量系统包括：•电导式电导率传感器CLS16D 或CLS16•变送器，例如：Liquiline M CM42•测量电缆，例如：Memosens 数据电缆CYK10或CPK9连接模拟式传感器2测量系统示意图(连接Memosens 传感器)1Liquiline M CM42变送器2Memosens 数据电缆3Condumax CLS16DCondumax CLS16D/CLS16Endress+Hauser 3通信和数据处理(仅适用于CLS16D)与变送器通信始终将Memosens 数字式传感器连接至Memosens 变送器。