VITSON产品说明书(中文英文)

深圳市慧拓鑫科技有限公司

Shenzhen Hui Tuo Xin Technology Co., Ltd.

产品资料

Product information

1、TOP电源防雷箱系列（TOP Power lightning protection box series） (2)

2、TP 限压型电源防雷模块系列（TP V oltage limiting type power supply lightning protection module series）5

3、TP直流电源防雷模块系列（TP DC power supply lightning protection module series） .. 8

4、TCP电源未端精细防护防雷器系列（TCP Power supply terminal fine protective lightning arrester series）11

5、TDC 电源插座(TDC Power supply lightning protection socket series) (14)

6、TV 视频防雷器系列(TV Video arrester series) (17)

7、T 视频/射频防雷器系列(T Video / RF lightning arrester series) (20)

8、TC控制线路防雷器系列( TC Control circuit lightning arrester series) (23)

9、10/100M网络线路防雷器(10/100M Network circuit lightning arrester) (26)

10、通讯专线防雷器(Communication line lightning arrester) (29)

11、TT天馈线路防雷器系列(TT Antenna line arrester series) (31)

1、TOP电源防雷箱系列（TOP Power lightning protection box series）

产品介绍Product introduction

TOP电源防雷箱系列依据IEC标准设计，8/20波形最大通流容量20KA-100KA，能对电源系统的浪涌电压进行有效的钳制，电源B、C、D级产品均具备。

TOP Power lightning protection box series is designed according to IEC standard, 8/20 wave maximum flow capacity of 20KA-100KA, to power system voltage surge effectively clamped, power supply B, C, D products have.

TOP电源防雷箱配系列具备测试指示灯功能，能有效的指示防雷箱工作电源、浪涌防护状态，并可选备雷击计数、远程遥信监测功能。

TOP Power lightning protection box series Have a test indicator function，Can effectively indicate the lightning protection box power supply、Surge protection status And optional lightning counting、Remote remote monitoring function

★电涌保护器失效报警功能/相零反接及接地不良报警

★（Surge protection device failure alarm function / Phase zero reverse connection and grounding alarm）

★雷击计数显示、电源指示功能（可选）

★Lightning counting display，Power indicator function（Optional）

★电浪保护器远程监测功能（失效）

★Remote monitoring function（Failure）

★残压低、响应时间快

★Residual depression and Fast response time

★安装设计人性化、结构严谨

★Installation design of humanity and Strict structure

★工作环境温度适应性强

★Working environment temperature adaptability

★外壳保护等级高

★Shell protection grade

产品适用范围：

The scope of products：

▲通信、电力、金融、民航、铁路等电源系统的保护

▲Communications, electricity, finance, civil aviation, railways and other power system protection

▲建筑物总配箱、室外配电箱、楼层分配箱

▲Buildings with a total box, outdoor distribution box, floor distribution box

▲配电柜电箱无安装位置但须安装第一级防雷设施的环境

▲Power distribution cabinet electric box without installation position but must be installed first stage lightning protection facility environment

▲无人值守但须安装第一级带遥信指示的防雷设备的环境

▲Unmanned but to be fitted with remote signal indicative of the first level of mine equipment environment

▲需要有第一级电涌保护失效指示及报警指示及雷电泄放记录的环境

▲Need to have the first surge protection failure indication and alarm indication and lightning discharge recording environment

产品图：

Product picture:

产品尺寸：

Prodct size chart:

安装说明:

Installation instructions：

1、取出箱子钥匙，插进锁孔打开防雷箱面板

1、Remove the box keys,Inserted into the keyhole to open the thunder box panel

2、防雷箱体固定在墙面上。

2、Lightning protection box fixed on the wall

3、用电缆剪线钳裁剪相应长度的黄、绿、红、蓝色四种电源线及黄绿双色地线。

3、Cutting the appropriate length of cable wire cutters, yellow, green, red, blue four power cord and the yellow-green ground

4、根据现场的接线方式对每条线末端做铜鼻子；选用≥150A开口线鼻子或者与线径相应的国标圆口线鼻子，开口线鼻子用电烙铁搪锡；圆口线鼻子用液压钳压接并搪锡。

4、According to the connection on each end of the line do copper nose；Selection of ≥ 150A opening line of the nose or with

a diameter corresponding to GB Round the mouth line nose Opening line of the nose with electric iron Boring tin；Round mouth lines the nose with the hydraulic crimping and boring tin

5、将防雷箱连接好。

5、Lightning box connected

6、把五条连接导线穿管固定；管可选用PVC管\槽、镀锌铁管\槽、黄腊管、波纹管、蛇皮管等。

6、The five connecting conductor pipe is fixed：Tube can be used PVC pipe \ trough, galvanized iron pipes \ slot, yellow wax tubes, bellows, snakeskin tube。

7、停电接线，把黄、绿、红、蓝、黄绿五种线分别与电源配电柜内L1、L2、L3、N、PE相并联连接，并联安装于电源系统的空气开关进线端，并确保连接可靠。

7、Blackout wiring，The yellow, green, red, blue, yellow and green five line is respectively connected with the power distribution cabinet L1, L2, L3, N, PE phase parallel connection，nstalled in parallel in the power system into the air switch line side And ensure a reliable connection

8、固定配电箱内的连接导线，恢复供电。

8、Fixed power distribution box connecting wire,Restoration of electricity

9、锁好防雷箱，按下测试按钮指示灯亮，安装完毕。

9、Lock the lightning protection box，Press the test button indicator light，and Installed

* 安装注意事项

*Installation Notes

1、必须由专业持证电工进行安装。

1、Must be professional certified electrician to install

2、接地电阻≤4Ω。

2、Grounding resistance ≤ 4Ω

2、TP 限压型电源防雷模块系列（TP Voltage limiting type power supply lightning protection module series）

产品介绍Product introduction

TP系列电源防雷模块依据IEC标准设计，8/20波形最大通流容量20KA-80KA，能对电源系统的浪涌电压进行有效的钳制，能对电源系统的浪涌电压进行有效的钳制，电源B、C、D级产品均具备，依据不同的配电系统（TT/TN/IT）可选择多种组合方式。

TP series SPD according to IEC standard design, 8/20 wave maximum flow capacity of20KA-80KA, to power system voltage surge effectively clamped, power supply B, C, D products have，According to different distribution system ( TT/TN/IT ) can choose a variety of combinations.

★模块设计、安装方便

★Modular design、Easy to install

★模块为标准35mm导轨式安装

★Module for the standard 35mm DIN rail installation

★内置过流过热、温控断路技术

★The built-in overcurrent overheat, temperature control circuit technology

★单模块最大放电电流：20-80kA（8/20μs）

★Single module of the maximum discharge current of 20-80kA (8/20μs)

★漏电流小、残压低

★Low leakage current, low residual voltage

★反应速度：10-9秒级

★Speed of response：≤1ns

★高能电涌保护

★High-energy surge protection

★失效指示

★become invalid indication

★遥控报警信号常开/常闭触点端子（可选）

★Remote alarm signal Normally open / normally closed contact terminal(Optional)

产品图片:

Product picture:

产品适用范围：

The scope of products：

▲通信、电力、金融、民航、铁路等电源系统的保护

▲Communications, electricity, finance, civil aviation, railways and other power system protection

▲建筑物总配箱、室外配电箱、楼层分配箱

▲Buildings with a total box, outdoor distribution box, floor distribution box

产品尺寸图：

Prodct size chart:

安装说明：

Installation instructions：

1、防雷模块前串联过流保护装置

1、Lightning protection module series overcurrent protection devices

2、防雷模块固定在35mm导轨上。

2、Lightning protection module is fixed at 35mm rail

3、用电缆剪线钳裁剪相应长度的黄、绿、红、蓝色四种电源线及黄绿双色地线。

3、Cutting the appropriate length of cable wire cutters, yellow, green, red, blue four power cord and the yellow-green ground

4、根据现场的接线方式对每条线末端做铜鼻子；选用≥150A开口线鼻子或者与线径相应的国标圆口线鼻子，开口线鼻子用电烙

铁搪锡；圆口线鼻子用液压钳压接并搪锡。

4、According to the connection on each end of the line do copper nose；Selection of ≥ 150A opening line of the nose or with

a diameter corresponding to GB Round the mouth line nose Opening line of the nose with electric iron Boring tin；Round mouth lines the nose with the hydraulic crimping and boring tin

5、将防雷模块连接好。

5、Lightning protection module connected

6、把五条连接导线穿管固定；管可选用PVC管\槽、镀锌铁管\槽、黄腊管、波纹管、蛇皮管等。

6、The five connecting conductor pipe is fixed：Tube can be used PVC pipe \ trough, galvanized iron pipes \ slot, yellow wax tubes, bellows, snakeskin tube。

7、停电接线，把黄、绿、红、蓝、黄绿五种线分别与电源配电柜内L1、L2、L3、N、PE相并联连接，并联安装于电源系统的空气开关进线端，并确保连接可靠。

7、Blackout wiring，The yellow, green, red, blue, yellow and green five line is respectively connected with the power distribution cabinet L1, L2, L3, N, PE phase parallel connection，nstalled in parallel in the power system into the air switch line side And ensure a reliable connection

8、固定配电箱内的连接导线，恢复供电。

8、Fixed power distribution box connecting wire,Restoration of electricity

9、安装完毕。

9、Installed

* 安装注意事项

*Installation Notes

1、必须由专业持证电工进行安装。

1、Must be professional certified electrician to install

2、接地电阻≤4Ω。

2、Grounding resistance ≤ 4Ω

3、TP直流电源防雷模块系列（TP DC power supply lightning protection module series）

产品介绍Product introduction

TP系列直流电源电涌保护器依据IEC标准设计,TP系列直流电涌保护器具备大的雷电流泄放能力，每位的最大放电电流20kA，适用于直流供电系统的末级保护，依据不同的直流电源电压可选择各种相应的规格。

TP series DC power SPD according to IEC standard design,TP series DC surge protector with a large lightning current discharge capacity of,Each of the maximum discharge current of 20kA,Suitable for DC power supply system of the final protection,On the basis of different DC power supply voltage can be selected by the corresponding specifications

★模块设计、安装方便

★Modular design、Easy to install

★模块为标准35mm导轨式安装

★Module for the standard 35mm DIN rail installation

★内置过流过热、温控断路技术

★The built-in overcurrent overheat, temperature control circuit technology

★单模块最大放电电流：20-80kA（8/20μs）

★Single module of the maximum discharge current of 20-80kA (8/20μs)

★漏电流小、残压低

★Low leakage current, low residual voltage

★反应速度：10-9秒级

★Speed of response：≤1ns

★高能电涌保护

★High-energy surge protection

★失效指示

★become invalid indication

★遥控报警信号常开/常闭触点端子（可选）

★Remote alarm signal Normally open / normally closed contact terminal(Optional)

产品图片:

Product picture:

产品适用范围：

The scope of products：

▲直流配电屏

▲DC distribution screen

▲直流供电设备

▲DC-powered equipment

▲直流配电箱

▲DC distribution box

▲电子信息系统(如消防机房直流线路)▲Electronic information system()

产品尺寸图：

Prodct size chart:

安装说明：

Installation instructions：

1、防雷模块前串联过流保护装置

1、Lightning protection module series overcurrent protection devices

2、防雷模块固定在35mm导轨上。

2、Lightning protection module is fixed at 35mm rail

3、连接线线径要求：TP24DC、TP48DC、TP75DC、TP110DC、TP380DC，连接线≥6 mm2，接地线≥10 mm2。

3、Cable diameter requirements：TP24DC、TP48DC、TP75DC、TP110DC、TP380DC, Connecting wire≥6 mm2，Ground wire≥10 mm2

4、连接导线长度要求:电涌保护器两端的连接导线长度≤0.5米。

4、Connecting wire length requirements：Surge protection devices at both ends of connecting wire length≤0.5m

5、TP电涌保护器应安装在直流供电设备的负荷侧。

5、TP Surge protective device should be installed in DC power supply equipment of the load side

6、TP电涌保护器前端必须串联过流保护装置，过流保护装置参数的选择：

TP380DC,额定电流32A，分断电流10KA；TP24DC、TP48DC、TP75DC、TP110DC，额定电流16A，分断电流6KA。

6、TP Surge protective device, front-end must be connected in series overcurrent protective device，rameter selection of overcurrent protective devices: TP380DC,Rated current 32A，Breaking current 10KA；TP24DC、TP48DC、TP75DC、TP110DC, Rated current 16A，Breaking current 6KA

7、安装距离：与电压开关型电涌保护器距离≥5米。

7、Installation distance：Voltage switch type surge protector distance≥5m

8、安装完毕。

8、Installed

4、TCP电源未端精细防护防雷器系列（TCP Power supply terminal fine protective lightning arrester series）

产品介绍Product introduction

TCP系列模块化电源防雷器依据IEC标准设计，TCP系列电源防雷器每位具备2路电涌保护功能，每位的最大放电电流10KA （8/20μs），适用于供电系统的末级保护，依据不同的电源电压选择各种相应规格。

TCP Series modular power supply SPD according to IEC design,TCP Series SPD each with 2-way surge protector, Each the maximum discharge current of 10KA (8/20μs)，Apply to the supply system of The last level protection

★失效检测指示

★become invalid indication

★单模块最大放电电流：10kA（8/20μs）

★Single module of the maximum discharge current of 10kA (8/20μs)

★模块为标准35mm导轨式安装

★Module for the standard 35mm DIN rail installation

★内置过流过热、温控断路技术

★The built-in overcurrent overheat, temperature control circuit technology

产品图片:

Product picture:

产品适用范围：

The scope of products：

▲未级保护

▲The latter level protection

▲对安装空间要求较小的设备保护

▲Installation space requirements of smaller equipment protection

产品尺寸图：

Prodct size chart:

产品安装说明：

Installation instructions：

产品安装时,首先须将产品连接至可靠地线。

Product installation, the product must be connected to a reliable ground.

1、将TCP系列浪涌保护器固定到35mm标准导轨上。

1、TCP series SPD is fixed to the 35mm standard rail

2、TCP电涌保护器与被保护设备安装距离≤1米。

2、TCP SPD and the protected equipment installation distance ≤ 1 m.

3、将被保护设备原输入线路插入TCP电涌保护器标有( IN )端口螺柱卡接孔内，标有(OUT)端与设备连接，锁紧螺丝。

3、Protective equipment of the original input line will be inserted TCP surge protection device marked with(IN) port stud card access hole(OUT) end device is connected, tighten the screws.

4、接地要求：

4、Grounding requirements：

4.1、TCP系列电涌保护器的地线须接在标有In端的接地螺丝上，接地线≥2.5 mm2。

4.1 TCP series surge protector ground shall be connected to the grounding screw on the In side，The ground wire ≥ 2.5 mm2

4.2、接地电阻≤4Ω。

4.2、Grounding resistance ≤ 4Ω.

5、异常状况

5、Abnormal conditions

5.1、当线路中信号电平超过选用的TCP电涌保护器的Uc值时，TCP电涌保护器会损坏，同时出现信号中断。

5.1、When the line signal level over the selection of TCP surge protector Uc value, TCP surge protection device will be damaged, while the interrupt signal.

5.2、当信号(或交流、直流电路)电流超过TCP电涌保护器的负载电流时，电涌保护器会发热损坏。

5.2、When the signal (or AC and DC circuit) current exceeds the load current of the TCP surge protector, surge protector, heat damage.

出现上述两种情况时，请迅速取下TCP电涌保护器，重新选择与线路信号特性相匹配的TCP电涌保护器。

The above two cases, quickly remove the TCP surge protector, re-select line signal characteristic that matches the TCP surge protector.

5、TDC 电源插座(TDC Power supply lightning protection socket series)

产品介绍Product introduction

TDC系列插座式电源电涌保护器依据IEC标准设计。用于设备端D级防雷保护，具有精细的防护性能，对于雷电过电压、电源过电压、电网闪变、电磁脉冲均有良好的防护。插座式配置将电涌保护器与电源插板完美结合，RFI/EMI滤波电路及级间协

调电感，可吸收射频/电磁干扰等线路电涌，延长设备正常工作寿命，降低长期运行成本。

TDC series socket power SPD according to IEC standard design. D-level lightning protection for the device-side,With a fine protective performance,The lightning over voltage, overvoltage, grid flicker, have good protection of electromagnetic pulse. Outlet configuration will be a perfect combination SPD and power strip,RFI / EMI filtering circuits and interstage coordination inductance, Can absorb radio frequency/electromagnetic interference and other line surges,Extend the normal working life,Reduce long-term running costs

★过流保护、过载保护

★Overcurrent protection, overload protection

★线路过热自动保护

★Automatic protection circuit overheating

★EMI/RFI噪声抑制

★EMI/RFI noise suppression

★电源指示

★Power indicator

★超宽工作电压范围

★Super wide operating voltage range

★电涌保护状态指示

★Protection status indication

★5000次插拔无故障

★The 5000plug without fault

★带独立接地螺丝

★With a separate ground screw

产品图片：

Product picture:

产品适用范围：

The scope of products：

1、计算机机房设备、监控机房设备、消防机房设备、电话机房设备、其它类机房设备

1、Computer room equipment，Control room equipment，Fire engine room equipment，Telephone room equipment，Other types of engine room equipment

2、电脑、传真机、复印机、其它办公用电设备

2、Computers, fax machines, copiers, other office electrical equipment

3、电视机、投影机、家庭音响、家用电脑、电话机、拨号网络设备

3、Televisions, projectors, home audio, home computers, telephones, dial-up network equipment

产品尺寸：

Prodct size chart:

安装说明：

Installation instructions：

1．TDC系列多功能电源防雷插座安装在被保护设备前端，距离被保护的设备越近越好。

1. TDC series of multi-function power mine socket is installed in front of the equipment to be protected，From the protected equipment, the closer the better

2. 电源开关按钮按下时，指示灯亮，则表示电源正常接通，插座可正常使用；反之，不可使用。

2. Power switch button is pressed, the indicator light indicates that power is properly connected, socket can be used normally; the contrary, can not be used

3. 被保护设备的负载电流≤10A。超负载使用会自动断开电源，按下恢复键可恢复。

3. Equipment to be protected load current≤10A，Super load will automatically disconnect the power，Press the restore button recoverable

4．防雷插座配有接地端子，必要时与防雷地线相连。

4. Lightning protection socket with a ground terminal, when necessary and lightning protection grounding.

5．防雷组件失效指示灯亮时，则表示其防雷组件已失效；说明防雷插座已经损坏，需维修或更换。

5. Lightning protection components failure indicator light，Said its lightning protection component is invalid，Mine socket damaged，Required to repair or replace

6、TV 视频防雷器系列(TV Video arrester series)

TV系列监控系统防雷器依据IEC标准设计，采用了两级串联式联动保护，8/20波形最大通流容量10KA，主要用于保护监控系统前端设备。交/直流供电模式均有对应产品，带云台控制/不带云台控制摄像枪均有对应产品。多功能一体化设计，降低了保护成本和安装难度，减少安装的占用空间，最大限度的利用等电位保护原理使保护效果更为理想。

TV series monitoring system SPD according to IEC standard design，A two-stage tandem linkage protection，8/20 waveform maximum through-flow capacity 10KA，Mainly used for the protection of the monitoring system front-end device。AC / DC power supply mode to have the corresponding product，Take control / without control PTZ camera gun are the corresponding product。Multi-function integrated design，Reducing the protection cost and the installation

difficulty，To reduce the installation space，Maximize the use of equipotential protection principles so that the protective effect is more ideal.

★多功能防护选择

★Multi function protective selection

★最大放电电流10KA，两级联动

★Maximum discharge current of 10KA,Two level linkage

★插入损耗低

★Low insertion loss

★皮秒的反应速度

★Picosecond response speed

★失效指示（LED）

★Failure indication（LED）

产品图片：

Product picture:

产品适用范围：

The scope of products：

▲摄像机保护（带云台控制）

▲Camera protection（PTZ control）

▲摄像机保护（不带云台控制）

▲Camera protection（Without PTZ control）

产品尺寸：

Prodct size chart:

安装说明：

Installation instructions：

1、将TV系列防雷器固定在墙上或放置于可靠平面，防雷器IN端接输入线，OUT端与设备相连接。

1、TV series SPD is fixed to the wall Or placed in a reliable plane，SPD IN connected to input line, OUT terminal and equipment connected.

2、产品安装需进行可靠接地，接地电阻≤4Ω以下。

2、Product installation needs reliable grounding ，Grounding resistance ≤ 4Ω

3、被保护设备与防雷器的间距≤1米。

3、The protected equipment and SPD pitch≤ 1meters.

4、异常状态：

4、Abnormal state：

4.1、当信号或电源电平超过TV电涌保护器的Uc值时，TV电涌保护器会损坏，同时出现信号中断。

4.1、When the signal or power level exceeds TV SPD value of Uc, TV SPD will damage, appear at the same time signal interrupt

4.2、当信号或电源的负载电流超过TV电涌保护器的负载电流时，电涌保护器会发热损坏。

4.2、When the signal or power of the load current exceeds TV SPD of the load current, SPD will heat damage

出现上述情况时，取下TV电涌保护器，重新选择与被保护设备匹配的电涌保护器。

Appear afore-mentioned circumstances, Remove the TV SPD, To choose and the protected equipment matching of SPD

7、T 视频/射频防雷器系列(T Video / RF lightning arrester series)

T系列视频/射频防雷器依据IEC标准设计，采用了两级串联式联动保护，8/20波形最大通流容量10KA，主要用于摄像机视频信号、监控主机端视频信号防护。产品主要有1路和16路两种模式，接口适用于F头、N头两种射频和BNC头视频，适用于有线电视、公共电视、监控等系统以及视频点播系统等同轴通讯设备，安装便捷，反应速度快，低插入损耗。