模具常用名称中英文对应表
模具名称中英文对照
模具名称中英文对照模具名称中英文对照模胚Mold Base顶板Top Clamp Plate脱料板Runner Stripper Plate热流板Spacer Plate母模板A Plate推板Stripper Plate公模板B Plate承板Support Plate方铁Spacer Block面针板Ejector Retainer Plate底针板Ejector plate底板Bottom Clamp Plate母模仁Cavity Insert公模仁Core Insert滑块Slide斜顶Lift镶针Core Pin镶件Insert互换镶件Change Insert滑块镶件Slide Insert铲鸡Wedge压条Plate斜导柱Slide Pin耐磨板Wear Plate导向块Guide Block斜顶导向块Lift Guide Block 滑块导轨Slide Guide滑块束块Slide Wedge斜顶底座Lift Base唧咀Sprue Bushing分流锥Sprue Spreader定位环Locating Ring胶口衬套Sprue Bushing电热衬套Hot Tip Bushing 电热管Heater电热圈Heater Band线接头Power控温耦合器Thermocouple顶针Ejector Pin扁顶针Rec. Ej. Pin方顶针Sqrt. Ej. Pin双节顶针Step Ej. Pin司筒Ejector Sleeve双节司筒Step Ej. Sleeve顶出块Ejector Block勾针Sprue Pin拉杆Puller Pillar拉料销Runner Lock Pin开闭器Slide Lock Set尼龙开闭器Parting Lock复位杆Return Pin支撑柱Support Pillar垃圾钉Stop Pin限制块Stop Block开模止板Stop Plate日期章Date Marked Pin压力胶Rubber Spring限位开关Limits Switch弹簧Spring轻小载荷弹簧Lightest Load Spring轻载荷弹簧Light Load Spring中载荷弹簧Medium Load Spring重载荷弹簧Heavy Load Spring极重载荷弹簧Super Load Spring圆线弹簧Wire Spring耐热弹簧Heatproof Spring弹簧柱Spring Rod波子弹簧Ball CatchO型圈O Ring隔水片Baffle Boards喉塞Pipe Plug水道塞子Coolant Plug水管Water Connection喷水管Cascade Water Junction挡水板Plug Baffles快速接头Jiffy-Tile Sockets水管无头螺丝Water Bass Pressure Plugs导柱Guide Pin直导套Straight Guide Bush有托导套Shoulder Guide Bush 顶针板导柱Ejector Guide Pin 顶针板导套Ejector Guide Bush限位螺丝Stop Bolt无头螺丝Screw Plug内六角螺丝S.H.C.S平头小螺丝F.H.C.S外六角螺丝Hexangdlar Bolt定位销Dowel Pin定位钢珠Ball Plung锁模块Lock Block0度定位块Straight Block Set 斜度定位块Taper Block Set圆形定位器Taper Pin Set轴Shaft轴承Bearing齿轮Gear凸轮Cam Whee气阀Valves气压缸Air Cylinder油压缸Hydraulic Cylinder油压马达Hydraulic Motors油封Oil Close轴用C环"C"Type Ring轴用E环"E"Type Ring 孔止环Stop Hold Ring。
模具常用语中英文对照
模具常用语中英文对照种类中文名称英文名称中文名称英文名称模具种类连续模Progressive die 冲孔模Pierce die 机械手Transfer die 剪边模Trimming die 手动机械手Hand transfer die 下料模Blanking die 单工程模Single die 成形模Forming die 铸造结构模Cast die 折弯模Bending die 简易模Prototype die 围边模Flange die 铆合模Riveting die 拉伸模Draw die 复合模Compound die 快换模Changeable die工序类料带strip 料带图strip layout 工序process 冲导正孔pilot pierce 冲孔pierce 侧冲cam pierce 切边notch 切侧刃notch french 折弯bend 墩薄coin成形form 侧成形cam form 整形restrike 围边flange打凸米boss / dimple 打凸包emboss打字印stamp 打沙拉孔hourglass 面押coin burr 抽孔extrude hole 拍平flat 卷圆curl种类中文名称英文名称中文名称英文名称工序类旋转rotate 铆接rivet产品切边线trim line 铆螺母stake nut 切断cutoff 接刀口mismatch 料带带料处carrier tab 毛刺方向burr direction 压线groove 下料blanking模板类上托板top plate 下托板bottom plate 上垫脚upper parallel 下垫脚lower parallel 上模座upper die set 下模座lower die set 上垫板punch backup 下垫板lower backup 上夹板punch holder 下夹板die holder 上脱料板stripper 下模板die plate 冲头punch 凹模die零件类浮块lifter 浮料板lifter plate 成型公form punch 压料块pressure pad 切边冲头trim punch 刀口trim steel 沉头孔counter bore 冲孔入子button 顶针kick off / ejector 废料切断刀slug breaker 成型凹模forming die 整形公restrike punch 导尺rail 导尺顶杆lifter bolt 导料板rail plate 镶件/入子insert侧冲组件cam 滑块slide滑块上油槽oil groove 铲机driver码模槽mounting slot 储运块storage block 限位柱stop block 起吊孔handing hole 起吊环eyebolt 靠块heel脱料拉杆spool 模座导正块thrust heel种类中文名称英文名称中文名称英文名称零件类耐磨片wear plate 垫片shim压块keeper 初始管位first start pin键槽key slot 键key氮气弹簧nitrogen spring 螺旋弹簧coil spring聚氨酯弹簧urethane导柱guide post 导套guide bushing 插针pilot pin插针套pilot bushing 侧刃french传感器sensor 销dowel螺丝screw 拔牙jackscrew垫圈washer 盲销blind dowel压毛边冲头deburring punch 挡块stopping plate压线冲头groove punch 定位块location block字模冲头stamp punch 圆冲头round punch压筋冲头ribbon punch 气垫板air cushion plate 异形冲头special shape punch 气垫顶杆air-cushion eject-rod 切边冲头trimming punch 上压块pressure block加强筋冲头stiffening rib punch 弹簧箱spring box 定位板guide plate 弹簧箱顶杆spring-box eject-rod 压边圈binder 弹簧箱顶板spring-box eject-plate公差类公差tolerance 公差范围tolerance range 上公差upper tolerance 下公差lower tolerance 公差+/- 0.05 plus minus 0.05 形位公差图GD&T 平面度flatness 直线度Straightness 倾斜度angularity 垂直度perpendicularity 平行度parallelism 圆度roundness种类中文名称英文名称中文名称英文名称公圆柱度cylindricity 面轮廓度surface profile差类线轮廓度line profile 位置度true position 同轴度concentricity 对称度symmetry 圆跳动runout 全跳动total runout 尺寸dimension 角度值angle degree 尺寸全检报告dimensional layout 三次元尺寸报告CMM report冲床相关机械冲床mechanical press 油压机hydraulic press 吨位tonnage 行程stroke / travel 冲床上台面ram 冲床下台面bolster 冲床台面布置图press layout 冲床上的快速对正QDC 冲床气垫air cushion 码仔stirrup 闭合高度shut height T型槽T-slot 送料机feeder 送料高度feeding height工具卡尺caliper 千分尺micrometer 直尺ruler 高度尺height gage 丝攻screw tap 起子screwdriver 拨牙器jacker 扳手wrench 风磨机hand grinder 油石oil stone加工类开料cutting material 钻drill (DR) 攻牙tap 铰ream铣mill 车lathe电脑锣NC mill 线切割wire cutting(W/C) 磨grind 刨planer电火花EDM 镭射laser cutting 倒角chamfer xx的精加工finish XX真空热处理vacuum heattreatment镀钛TD coating 退磁demagnetization 烧焊weld4.1.2 加工说明对照表：加工说明Machining Note注:有0.00的地方为数据填入处外导套OUTER GUIDE BUISHING 起吊杆HANDING PIN实数铣通MILL THRU 正反两面各铣TOP SIDE AND OPP SIDE MILLX:-￠0.00（氮气弹弓过孔，锣穿）单+0.00X:-￠0.00 (DR.THRU FOR GAS SPRING) S+0.00X:-￠0.00（氮气弹弓沉头，正面CNC单+0.00,锣深0.00.)X:-￠0.00 ( CNC C'BORE TOP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-￠0.00（氮气弹弓沉头，反面CNC单+0.00,锣深0.00.)X:-￠0.00 (CNC C'BORE OPP SIDE FOR GAS SPRING, S+0.00, DP0.00)X:-￠0.00（合销孔,铰)X:-￠0.00 (REAM FOR DOWEL)X:-￠0.00（合销孔,割)单+0.00X:-￠0.00 (W/C FOR DOWEL) S+0.00(正面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR) (反面沉头￠0.00*0.00深,内攻M0.00*1.5牙)(￠0.00*0.00 C'BORE DP.0.00 OPP. SIDE, TAP M0.00*1.5 THR) X:-￠0.00（合销孔,钻穿)X:-￠0.00 (DR.THRU FOR DOWEL)X:-￠0.00（一般孔,钻穿)X:-￠0.00 (DR.THRU HL)X:-￠0.00（穿丝孔,钻穿)X:-￠0.00 (DR.THRU FOR WEDM S.H.)X:-￠0.00（漏油孔,钻穿) 按向视图加工X:-￠0.00 (DR.THRU FOR DRAIN HL) ACCORDING VIEW DRAWING TO MACHINING X:-（漏油槽,反面CNC单+0.00,锣深0.00)X:- (CNC POCKET OPP.SIDE FOR DRAIN, S+0.00, DP0.00)X:-￠0.00（基准孔,铰)X:-￠0.00 (REAM FOR DATUM HL)X:-￠0.00钻穿（螺丝过孔)内攻M0.00牙X:-￠0.00 (DR.THRU FOR CLEARANCE HL, TAP M0.00 THR)(正面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 TOP SIDE)(反面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 OPP. SIDE)(侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00钻穿,反面攻深0.00,有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 OPP.SIDE, THR DP0.00)X:-M0.00钻穿,正面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP SIDE, THR DP0.00)X:-M0.00钻穿,正反面攻深0.00，有效牙0.00X:-M0.00 DR.THRU, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00) X:-M0.00盲孔,反面攻深0.00,有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 OPP. SIDE)X:-M0.00盲孔,正面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP WORK DP0.00 TOP SIDE, THR DP0.00)X:-M0.00盲孔,正反面攻深0.00，有效牙0.00X:-M0.00 BLIND HL, TAP DP0.00 TOP&OPP. SIDE, THR DP0.00) X:-M0.00盲孔,侧面分中攻深0.00,组模自配X:-M0.00 BLIND HL, TAP DP0.00 ON EDGE FROM CENTER , DIE MAKER FIT) (侧面沉头￠0.00*0.00深)(￠0.00*0.00 C'BORE DP0.00 EDGE SIDE)X:-M0.00盲孔,侧面分中钻深0.00X:-M0.00 BLIND HL, DR. DP0.00 ON EDGE FROM CENTERX:-M0.00（拨牙螺丝孔，攻穿）X:-M0.00 TAP.THRU FOR JACK SCREWX:-￠0.00（塞打过孔,钻穿)X:-￠0.00 DR.THRU FOR SPOOLX:-￠0.00（弹弓过孔,钻穿)X:-￠0.00 DR.THRU FOR SPRINGX:-￠0.00（弹弓孔,反面沉深0.00)有效深0.00X:-￠0.00 (C'BORE FOR SPRING DP.0.00 OPP.SIDE, USED DP.0.00)X:-￠0.00（弹弓孔,正面沉深0.00)有效深0.00X:-￠0.00 (C'BORE FOR SPRING DP.0.00 TOP.SIDE, WORK DP.0.00)X:-（避空孔,锣穿)单+0.00X:- (POCKET THRU)S+0.00X:-（避空孔,正面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 TOP SIDE)X:-（避空孔,反面CNC单+0.00,锣深0.00)X:- (POCKET, CNC MILL S+0.00 DP0.00 OPP SIDE)X:-￠0.00（避空孔,反面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 OPP.SIDE)X:-￠0.00（避空孔,正面CNC单+0.00,锣深0.00)X:-￠0.00 (POCKET, CNC MILL S+0.00, DP0.00 EDGE SIDE)X:-￠0.00（两用销过孔,割)单+0.00X:-￠0.00 (LIFTER PIN, W/C S+0.00)X:-（导尺避空,CNC单+0.00锣穿)X:- (POCKET FOR RAIL, CNC MILL THRU, S+0.00)X:-（导尺避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 TOP SIDE, S+0.00) X:-（导尺避空,反面CNC单+0.00，锣深0.00)X:- (POCKET FOR RAIL, CNC MILL DP.0.00 OPP. SIDE, S+0.00) X:-（浮块避空,正面CNC单+0.00，锣深0.00)X:- (POCKET FOR LIFTER, CNC MILL DP.0.00 TOP SIDE, S+0.00) X:-（浮块孔,割）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, W/C)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-（浮块孔,锣）单+0.00(反面避空单+0.00，锣深0.00)X:-（LIFTER HL, MILL)S+0.00(POCKET DP0.00 S+0.00 OPP.SIDE)X:-￠0.00（顶针孔,钻穿)（反面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 OPP. SIDE, TAP M0.00*1.5 THR)X:-￠0.00（顶针孔,钻穿)（正面沉头￠0.00*0.00深，内攻M0.00*1.5牙)X:-￠0.00 (EJECT PIN, DR.THRU.)(￠0.00 C'BORE DP0.00 TOP SIDE, TAP M0.00*1.5 THR)X:-￠0.00（导柱（导套）孔,CNC锣)单+0.00X:-￠0.00 CNC MILL FOR GUIDE PIN(BUSHING) S+0.00X:-￠0.00（导柱（导套）孔,割)单+0.00X:-￠0.00 W/C FOR GUIDE PIN(BUSHING) S+0.00X:-M0.00*1.5(止付螺丝，正面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 TOP SIDE)X:-M0.00*1.5(止付螺丝，反面攻深0.00)X:-M0.00*1.5(SET SCREW, TAP DP0.00 OPP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:-（INSERT HL, CNC MILL THRU S+0.00)(阴影部分正面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 TOP SIDE)(阴影部分反面沉头单+0.00，锣深0.00)(SHADE AREA, MILL DP0.00 S+0.00 OPP SIDE)X:-（入子孔,割）单+0.00X:-（INSERT HL, W/C S+0.00)(阴影部分扣位正面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 TOP SIDE)(阴影部分扣位反面锣深0.00)(SHADE AREA FOR HEAD POCKET, MILL DP0.00 OPP. SIDE)(正面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)注: 此处的沉头不能用C'BORE, 只有圆形的沉头才用C'BORE.(反面沉头单+0.00，锣深0.00)(POCKET, MILL DP0.00 TOP SIDE)X:-（入子孔,CNC单+0.00,锣穿)X:- (INSERT HL, CNC MILL THRU. S+0.00)X:-（入子孔,正面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 TOP SIDE)X:-（入子孔,反面CNC单+0.00,锣深0.00)X:- (INSERT HL, CNC MILL DP0.00 S+0.00 OPP. SIDE)X:-￠0.00（插针孔,铰)单+0.00X:-￠0.00（REAM S+0.00 FOR PILOT PIN)X:-￠0.00（插针孔,割)单+0.00(正面沉头￠0.00*0.00深)X:-￠0.00（W/C FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-￠0.00（插针孔,钻穿)(正面沉头￠0.00*0.00深)X:-￠0.00（DR.THRU FOR PILOT PIN)(￠0.00 C'BORE DP0.00 TOP SIDE)X:-（冲头过孔,割)单+0.00(正面避空，CNC单+0.00，锣深0.00)(阴影部分扣位正面锣深0.00)X:-（W/C S+0.00 FOR PUNCH CLEARANCE HL)(POCKET, CNC DP 0.00 S+0.00 TOP SIDE)(POCKET SHADE FOR HEAD, DP0.00 TOP SIDE)X:-（冲头过孔,锣穿)单+0.00(正面避空，CNC单+0.00，锣深0.00)X:-（MILL THRU.FOR PUNCH CLEARANCE HL)(POCKET DP0.00 CNC S+ TOP SIDE)X:-（异形冲孔,直x斜x,割)单+0.00(双线部分，割)单+0.00X:-（W/C FOR SPECIAL HL, 0.00 LAND 0.00 TAPER, S+0.00) (W/C PER DOUBLE LINE S+0.00)X:-（冲孔,直x斜x,割)单+0.00X:-（W/C FOR PIERCE DIE HL, 0.00 LAND 0.00 TAPER S+0.00) X:-（冲孔,割)单+0.00X:-（W/C FOR PIERCE DIE HL S+0.00)X:-￠0.00（冲孔漏屎,钻穿)X:-￠0.00 (DR. THRU FOR CHUTE)X:-（异形冲孔漏屎,CNC单+0.00,锣穿）X:-￠0.00 (MILL. THRU FOR SPECIAL CHUTE S+0.00)X:-（产品落料斜度，实数斜30o锣）X:-（MILL 30 TAPER FOR PART RAMP NO CLEARANCE) X:-（漏屎斜度，直x斜45o锣）X:-（MILL FOR CHUTE 0.00 LAND 45 TAPER)反面沉深底面留0.00MILL UNTIL DP正面沉深底面留MILL UNTIL DP五金模具单词总结模具种类:连续模progressive die机械手transfer die手动机械手hand transfer die单工程模single die/line die复合模compound die铆接模riveting die铸造结构模cast die能快换的模changeover die泡沫模pattern互换性:公差tolerance上公差upper tolerance下公差lower tolerance公差范围tolerance range公差+/- 0.05 plus minus 0.05形位公差图GD&T平面度flatness直线度straightness倾斜度angularity垂直度perpendicularity / squareness平行度parallelism圆度roundness / circularity圆柱度cylindricity面轮廓度surface profile线轮廓度line profile位置度true position同轴度concentricity对称度symmetry圆跳动runout全跳动total runout尺寸dimension角度angle degree全尺寸报告dimensional layout工艺性:料带strip料带图strip layout工序process冲导正孔pilot pierce冲孔pierce侧冲cam pierce切边notch成形后的切边trim切侧刃french trim / fringe trim 厚料切边后的精修边shave 折弯bend墩薄coin折弯处压筋gusset成形form侧成形cam form整形restrike / rehit围边flange压线/压长条状筋ribbon打凸米boss / dimple打凸包emboss打字印stamp打沙拉孔hourglass面押coin burr抽孔extrude hole拍平flat / spanking包边hem edge压角cone张角flare切舌lance半剪knockout卷圆curl/热恶劣旋转rotate铆接rivet铆螺母stake nut切断cutoff接刀口mismatch料带带料处carrier tabs毛刺方向burr direction产品切边线trim line模具零件:模具die / tool上托板upper mounting plate 上垫脚upper parallel 上模座upper die set上垫板punch backup上夹板punch holder止挡板traveling stop脱料板stripper下模板die plate下垫板die backup plate下模座lower die set下垫脚lower parallel上托板base mounting plate浮块lifter浮料板lifter plate成型公form punch压料块pressure pad切边冲头trim punch刀口trim steel刀口直身位land直5斜1 5mm Land 1 taper 刀口上沉头的深度die life 沉头counter bore冲头倒斜shear高低冲stagger punch球锁冲头ball-lock punch球锁座ball-lock retainer冲孔入子button顶针kick off / ejector废料切断刀slug breaker成型凹模form die整形公restrike form punch 导尺rail /stock guidance导尺顶杆lifter bolt导料板rail plate镶件/入子insert侧冲组件cam滑块slide滑块上油槽oil groove铲机driver码模槽mounting slot储运块storage block限位柱stop block起吊孔handing hole起吊环eyebolt模柄shank靠块heel摆块rocker bender脱料板拉杆stripper bolt模座导正块thrust耐磨片wear sheet耐磨板wear plate垫片shim两用销lifter pin初始管位first start pin内限位standoff压块keeper导柱导套压块keeper/ boss 键槽key slot键key氮气弹簧gas spring / nitrogen spring 氮气弹簧安装法兰mounting flange 氮气弹簧系统nitrogen manifold螺旋弹簧coil spring聚氨酯弹簧urethane弹簧套spring cage导柱guide post导套guide bushing插针pilot pin插针套pilot bushing插针通孔pilot through hole侧刃french误检装置misfeeder传感器sensor误检杆trigger油嘴oil nipple销针dowel pin螺丝screw牙thread拔牙jackscrew内六角螺钉socket head screw 垫圈washer螺塞screw plug盲销blind dowel行程,走位stroke / travel吨位tonnage机械冲床mechanical press油压机hydraulic press冲床下台面bolster冲床上台面ram冲床台面布置图press layout冲床码模槽press mounting slot 冲床气垫air cushion码模钳stirrup闭合高度shut height送料高度feeding height送料机feederT型槽T-slot避位clearance /pocket掏空pocket挂台head扣位pocket of head通气孔air vent hole漏油孔drain hole漏料孔slug hole基准孔datum hole通孔through hole穿丝孔first wire holeT型槽T-slot拔牙jackscrew摆块rocker bender闭合高度shut height避位clearance /pocket侧冲组件cam侧刃french插针pilot pin插针套pilot bushing插针通孔pilot through hole铲机driver沉头counter bore成型凹模form die成型公form punch冲床码模槽press mounting slot 冲床气垫air cushion冲床上台面ram冲床台面布置图press layout冲床下台面bolster冲孔入子button冲头倒斜shear初始管位first start pin储运块storage block穿丝孔first wire hole传感器sensor弹簧套spring cage氮气弹簧gas spring / nitrogen spring 氮气弹簧安装法兰mounting flange氮气弹簧系统nitrogen manifold刀口trim steel刀口上沉头的深度die life刀口直身位land导尺rail /stock guidance导尺顶杆lifter bolt导料板rail plate导套guide bushing导柱guide post导柱导套压块keeper/ boss垫片shim垫圈washer顶针kick off / ejector吨位tonnage废料切断刀slug breaker浮块lifter浮料板lifter plate高低冲stagger punch挂台head滑块slide滑块上油槽oil groove机械冲床mechanical press基准孔datum hole键key键槽key slot聚氨酯弹簧urethane靠块heel扣位pocket of head两用销lifter pin漏料孔slug hole漏油孔drain hole螺塞screw plug螺丝screw螺旋弹簧coil spring码模槽mounting slot码模钳stirrup盲销blind dowel模柄shank模具die / tool模座导正块thrust内六角螺钉socket head screw 内限位standoff耐磨板wear plate耐磨片wear sheet起吊环eyebolt起吊孔handing hole切边冲头trim punch球锁冲头ball-lock punch球锁座ball-lock retainer上垫板punch backup上垫脚upper parallel上夹板punch holder上模座upper die set下托板base mounting plate 上托板upper mounting plate 送料高度feeding height送料机feeder掏空pocket通孔through hole通气孔air vent hole脱料板stripper脱料板拉杆stripper bolt误检杆trigger误检装置misfeeder下垫板die backup plate下垫脚lower parallel下模板die plate下模座lower die set限位柱stop block镶件/入子insert销针dowel pin行程,走位stroke / travel压块keeper压料块pressure pad牙thread油压机hydraulic press油嘴oil nipple整形公restrike form punch 直5斜1 5mm Land 1 taper 止挡板traveling stop机加工:开料cutting material钻drill (DR)攻牙tap铰ream铣mill车lathe电脑锣NC mill线切割wire cutting (W/C)磨grind刨planer电火花EDM镭射laser cutting倒角chamfer精加工finish XX真空热处理vacuum heat treatment镀钛TD coating退磁demagnetization烧焊weldG :40-M6BLIND HL,TAP DP18.00 OPP SIDE,THR DP18.00) 盲孔，反面攻深**G10:4-M30BLIND HL,TAP DP18.00 EDGE SIDE)盲孔，侧攻深** (%%c34.00*14.00 C'BORE DP14.00 TOP SIDE) 正面沉头多少×多少深G2 :24-%%c8.00(REAM FOR DOWEL WORK DP16.00 OPP SIDE,DR%%c6.00 HL)G2 :24-%%c8.00(合销,背铰深16.00,有效深,内钻%%C6.00通孔) G4 :3-%%c10.00(基准孔,背铰深20.00)背面锣25.00*25.00方形沉头，深 1.00%%P0.01 (REAM FOR DATUM HL DP20.00,MILL25.00*25.00 OPP SIDE DP1.00%%P0.01) M:2-%%c15.00(弹簧孔,锣深33.00) (C'BORE OR SPRING DP33.00 TOP SIDE,WORK DP33.00)X :3-%%c32.00(导套孔,锣穿,单+0.01)(MILL THRU FOR GUIDE BUSHING S+0.01)G :2-M10盲孔,侧攻深30.00(有效深)(BLIND HL,TAP WORK DP30.00 EDGE SIDE)(沉头5.20%%P0.05深)(SLOT DP5.20%%P0.05 TOP SIDE)L :2-%%c8.000(合销,割)单+0.005 (W/C FOR DOWEL)S+0.005 盲孔,攻深20.00(有效深) (BLIND HL,TAP DP20.00 TOP SIDE,THR DP20.00)(插针孔,割,单+0.01) (W/C S+0.01 FOR PILOT PIN)(避位孔,背锣9.80(有效深) (POCKET,MILL DP9.80 OPP SIDE WORK)(冲头过孔,锣穿) (MILL THRU FOR PUNCH CLEARANCE HL)(导柱孔,锣穿,单+0.005) (MILL FOR GUIDE PIN) S+0.005避位槽,背锣深19.00) (POCKET,MILL DP15.40 OPP SIDE)(背,沉头%%c14.00，掏深留11.00) (%%c14.00 C'BORE UNTIL DP14.00 OPP SIDE)下模刀口，实数割，直5斜1.5 （内钻%%C5.0穿丝孔）W/C S+0.00 TRIM STEEL,5.0LAND 1.5TAPER,(DR THRU%%c3.00 WEDM S.H)(MILL FOR INSERT DP30.0%%P0.01 S+0.01)(入子槽,锣深30.00%%p0.01,单+0.01)(氮气槽,背锣深 4.00%%P0.1,单+0.1) (GAS SPRING MILL DP4.00 OPP SIDE)S+0.1按向视图加工ACCORDING VIEW DRAWING TO MACHINING 试模材料:热扎板HRS (hot-roll steel)冷扎板CRS (cold-roll steel)不锈钢板Stainless steel镀锌板galvanized steel镀铝锌板galvalume steel热扎酸洗板HRPO steel (hot-rolled pickled and oiled steel)工具:卡尺caliper千分尺micrometer拨牙器jacker扳手wrench丝攻screw tap起子screwdriver码模钳stirrup设备/工具:3D Programmable CMM三次元检测仪3D CMM Beam Drilling Machine摇臂钻Bench Drilling Machine钻铣床Caliper卡尺CNC EDM电火花机CNC Machine Center加工中心CNCCNC Milling Machine数控铣床CNCCNC Planer Type Milling Machine龙门刨铣床Hardness Tester 硬度计Height Gauge高度仪High Wire Cutting快走丝Hole Puncher 打孔机Horizontal surface grinder小水磨/卧式平面磨床Horizontal surface large grinder大水磨Lathe车床Measurement Surface Plate测量平台Metal Saw Machine锯床Milling Machine铣床Oil Press油压机Pin Gauge标准针规Plastic Injection Machine注塑机Point to Point CMM三次元测量仪Precision surface grinder精密手摇磨Press冲床Projector profile投影机Shear Press剪板机Slow Wire Cutting慢走丝Vertical Milling Machine卧式强力铣床扳手wrench拨牙器jacker卡尺caliper码模钳stirrup起子screwdriver千分尺micrometer丝攻screw tapCARVE 雕刻pothook 挂钩SPECIAL HL 异形孔漏斗 filler角铁 ANGLE IRON展开 expanding微调开关 INCHING SWITCH合叶 HINGE优力胶 RUBBER球锁垫板 LOCK WASHER双线边刀口,不倒角TRIM STEEL NEAR THE DOUBLE LINE NO CHAMFER滑块座:SLIDE SET机械:（engine type) liquid cooled, in-line, 4cylinder, carb (发动机型号)水冷，直列，四缸，化油器式(engine) compression ratio (发动机)压缩比(engine) displacement (发动机)排量(engine) fuel (发动机)燃料13-mode 13工况3rd gear 三档齿轮3-way seat 三向座椅4WD control device 四轮驱动控制装置4WD indicator switch 四轮驱动指示灯开关4WD lamp electrical connection 四轮驱动指示灯接线4WD switch 四轮驱动开关5th synchromesh assy. 五档同步器总成6PK belt 6PK 多楔驱动皮带A / C compressor assembly 空调压缩机总成A / C control assembly 空调控制装置A/C & heater assy. 空调加热器总成A/C blower 空调鼓风机A/C clutch 空调压缩机离合器A/C compressor MTG bracket 空调压缩机安装支架A/C control assy. 空调控制器A/C housing assy. 空调箱总成A/C low pressure switch 空调低压开关A/C mode select switch 空调状态选择开关abdomen performance criterion 腹部性能指标Abdominal Peak Force 腹部力峰值ABS 防抱死制动系统acceleration fuel system 加速系统acceleration running noise level 加速行驶噪声accelerator interlocking type 加速踏板联锁式accounting foundation 财政基础Actual cycle work 实际循环功Actual torso angle 实际躯干角adapter 连接器additional features 附加装置additional rule 附加法规。
模具常用名称中英文对照表
24. 电极：Electrode——缩写：Elc
25. 限位：LIMIT——缩写：LT
26. 导向板：GUIDE PLATE——缩写GUP
27. 直顶块： STRAIGHT EJ BLOCK——缩写STB
28. 补强板： STIFFENING PLATE——缩写STP
5. 热流道板(热浇道板)：Hot runer——缩写：HR
6. 母模（定模）：Cavity——缩写：Cav
7. 导柱：Guide Pin——缩写：G.P.
8. 导套：Guide bush——缩写：G.B.
9. 复位杆：Release Pin——缩写：R.P.
10. 动模型芯（中间体）：Core——缩写：Cor
11. 模脚：Support parallels——缩写：Supa
12. 侧翼块：Side block——缩写：Sibk
13. 轮Leabharlann ：Plin——缩写：Plin 14. 模座（底座）：Die holder——缩写：Dho
15. 镶件：Insert——缩写：Ins
16. 滑块（行位块）：Slide——缩写：Sld
模具数模命名规则及常用名称中英文对照表（含缩写）
1. 射嘴：Nozzle——缩写：Noz
2. 定位圈：locating ring——缩写：locr
3. 浇口套：Sprue bush(Sprue busing) ——缩写：Sprb
4. 垫板(固定板)：Base Plate——缩写：BP
17. 斜顶块：Lifter——缩写：Lit
18. 推板(顶板)：Eject Plate——缩写：EP
模具专业词汇中英文对照表
模具专业词汇中英文对照表1. 模具材料（Mould Materials）•合金钢（Alloy Steel）•不锈钢（Stnless Steel）•工具钢（Tool Steel）•铸造铁（Cast Iron）•铝合金（Aluminum Alloy）•铜合金（Copper Alloy）•硅橡胶（Silicone Rubber）•塑料（Plastic）•陶瓷（Ceramic）2. 模具零件（Mould Components）•模板（Mold Base）•注塑装置（Injection Unit）•顶出器（Ejector）•气嘴（Nozzle）•间隙（Clearance）•提位器（Lifter）•滑块（Slide）•定位圈（Locating Ring）•膜背（Backing Plate）•挡块（Stop Block）•压板（Clamp Plate）•冷却管（Coolant Pipe）•驱动装置（Drive Unit）3. 模具制造工艺（Mould Manufacturing Process）•设计（Design）•切割（Cutting）•加工（Machining）•组装（Assembly）•调试（Debugging）•精修（Finishing）•表面处理（Surface Treatment）•检查（Inspection）•试产（Trial Production）4. 模具加工方式（Mould Processing Methods）•铣削（Milling）•磨削（Grinding）•拉刀（Planing）•镗削（Boring）•钻孔（Drilling）•线切割（Wire Cutting）•抛光（Polishing）•火花加工（EDM）5. 模具设计要点（Key Points in Mold Design）•壁厚（Wall Thickness）•浇注系统（Gating System）•冷却系统（Cooling System）•排气（Venting）•气罩（Bubbler）•顶杆（Ejector Pin）•脱模斜度（Draft Angle）•零件坯料与尺寸（Blank and Dimensions）•对位方式（Alignment Method）•衬套（Insert）•翻制（Flip Mold）•分模（Split Mold）6. 模具维护与保养（Mold Mntenance）•模具清洁（Mold Cleaning）•润滑（Lubrication）•排浆（Purging）•磨损修复（Wear Repr）•抛光修复（Polish Repr）•零件更换（Component Replacement）•修复记录（Repr Record）•数字化管理（Digital Management）7. 模具常见故障及解决方法（Common Mold Faults and Solutions）•翘曲（Warping）•缺陷（Defects）•泛油（Flash）•磨损（Wear）•烧坏（Burning）•掉件（Part Ejection）•插损（Insert Damage）以上仅是模具专业领域常用词汇的一个简单对照表。
模具常用名称中英文对应表
模具常用名稱中英文對應表彈弓膠Rubber Spring R.S.斜邊釘Taper InterLock T.L.鋼公electrode熱膨脹系數thermal expanion coefficient拉膠Parting Lock PA.L.斜導柱Angular Pin A.P.加工程序secondary process粘度viscosity 頂針Ejector Pin E.J.P.定位扣"P" Lock P.K.翹曲warpage 扁頂針Ejector Blade E.J.B.銷釘Dowel Pin D.P.有托頂針Stepped Ejector Pin S.E.J.P.斜鎖位taper Block Set-ky TYPE T.B.S.唧嘴sprue bushings附針(導柱)guide pins司筒針Ejector Sleeves E.J.S.水口扣針butt joint司(導套,套司)guide pin bushings頂針ejector pins平行板parallels單頭柳釘blind rivet電阻焊接resistance welding頂板ejector plates壓板clamping plate平接butt joint固定圈retaining ring面針板ejector pin retainer plate墊片pressure電動螺絲批screw driver,electric螺絲批screw driver邊釘loader pins碼板mountingplates氣動螺絲批screwdriver,pneumatic點焊spot welding受力單位force units托板(固定器)retainers換能器energy converter彈簧夾spring clips受力板force plate勾針pot plungers 焊條filler rod彈簧墊圈spring washer模板cavity plates頂針pots磨擦焊接friction welding雙頭螺栓stud模塊cavity blocks頂針板pot retainers氣焊gas welding轉矩扳鉗torque wrench模鑲件cavity inserts托板backing plates膠glue觸針welding horn口哥塊core blocks頂針knockout pins熱壓封口heat sealing超聲焊接ultrasonic welding內口哥鑲件core inserts頂出條knockout bars搭接lap joint固定口哥鑲件fixed cores頂出板knockout pin plates保險螺絲lock nut/lock washer活動口哥鑲件moveable cores壓條,碼板gibs 螺母nut行位,滑動板slideslayout排位web impregnation網架浸漬release agent脫模劑knockout pin同"ejector pin"guaranteed tool life 制模公司保証啤數rotation spindle旋轉軸knockout plate同"ejector plate"spare part requested后補件ante chamber預接待室roving紗束locating ring定模環tech point checklist工程提點latch鎖模扣seamless無縫mould insert模型嵌件parting line分模線puller拉針solidify凝固化pinpoint submarinegate針狀隱蔽澆口gating point水口點oil grooves油坑spray gun噴漆槍port壓力筒cavity marking頭號sheet steel薄鋼squeegee涂刷劑punch plate沖孔板date code日期指示印mould ledge模架steam jacket汽套ribs肋條,骨位12NC marking12N印spray paint噴油surge tank溢水槽ring gate環形澆口mould marking模編號tempo print絲印transfer chamber傳送室round support block園托板sub-contracting item外判加工water circuit水路vacuume pump真空泵runner澆道sketch草圖vent通氣孔runner plate澆道板split mould裂開式模finishing表面處理mould stripping出模,胱模,下模spider gate=spoko gate輪輻澆口2 plate mould2板模polish磨光sprue gate豎澆口combined tool合作模grin磨床sprue bushing豎澆口？套lathe車床sprue puller澆口拉鉤mill銑床standard gate標准澆口wire cut線切割stripper plate脫模板support block托板milling銑flash/buns披鋒air vent inserts氣坑milling cutter銑刀flow mark/flow lines/silverstreak 射絞spare parts備用部分nitriding氮化finger marks/fingerstaing/finger print 手指印safety systems安全系統photo-engraving光刻improper degating/gate toolong 水口過長mould ability可注塑膠pitch節距mixed colour/off colour 顏色不對稱short moulding走膠不齊polishing磨光orientation移位sink marks凹痕,縮水reamer鉸刀、鉸床ripples波浪紋warpage彎曲變形reaming絞孔scratched刮花paint ability可噴油,絲印roller coating滾筒涂層short shot缺模no. of cpk dims控制尺寸數量sanding砂磨sink marks縮水痕sec.of cpk check 草圖控制尺寸位置scraper刮刀spray marks水花紋shaping修刨、成形string拖膠線mould polishing省模,模具拋(省) shear剪stress marks扯白痕EDM電火花,放電加工slotting立刨thickness out of spec./undersize 尺寸不合wire EDM線切割snips平頭剪unstretched未拉spanner扳手vent marks氣紋texture蝕紋spray painting噴漆warpage扭曲，熱變形water contamination水漬three-plate mould三層模two-plate mould雙層模。
模具专业词汇英汉对照表
一、Introduction and Opening Conversations介绍和开场白People in the United States don’t always hands when they are introduced to one another. However, in a formal or business situation people always shake hands.1.A:Mary,this is Joe’s brother David.B:I’m very glad to meet you.C:It’s a pleasure to meet you.B:How do you like Texas so far?C: It’s really different from what I expected.D:Don’t worry. You’ll get used to it in no time.2.A：MRS. Smith，I’d like to introduce a friend of mine, Pierre Dubois.B：How do you do?C:Hello.B:What’s your impression of the United States?C：Well，I can’t get over how different the weather is here.B：Oh, you’ll get used to it soon.3.A:Wendy,I’d like you to meet my brother Sam.B:Hi/C:Nice to meet you.B:What do you like of Dallas.C:Well,I’m still feeling a little homesick and so many things seem strange to me.B：You’re bound to feel that way at first, I guess.4.A:Mrs.Hughs,this is Peter Brown.B:Pleased to meet you.C:How do you do?B:I hope you’re enjoying your stay here.C:If it weren’t for the climate, I’d like it here very much.B:It always take time to get used to a new place.二、Special Greeting 节假日的问候There are eight national holiday celebrated in the United States: New Year’s Day （Jan.）,Washington’s Birthday（Feb.）,Memorial Day(May.).the Fourth of July, Labor Day(Sep.).Veteran’s Day(Nav.),Thanksgiving(Nov.) and Christmas(Dec.),In addition, there are many state and local holidays.Our price is reasonable as compared with that in the international market.我们的价格和国际市场的价格相比还是合理的。
模具常用名词中英文对照表
模具常用名词中英文对照表模胚MOLD BASE直身锁(边锁)SIDE LOCK前模镶件CAVITY BLOCK条形锁RECTANGULAR LOCK后模镶件CORE BLOCK圆形锁ROUND LOCK前模小镶件CAVITY INSERY管钉DOWEL PIN后模小镶件CORE INSERT锁模板(安全锁)SAFTY STRAP定位圈（法兰）LOCATING RING吊模板(吊模方)EYEBOLT PLATE唧咀（浇口套）SPRUE BUSHING三板模延长唧咀EXTENSION SPRUE BUSHING行位块SLIDE BLOCK上水口铁UPPER RUNNER BAR行位镶件SLIDE INSERT下水口铁LOWER RUNNER BAR压条(限条)GIB截水口镶件RUNNER SHUT-OFF INSERT铲机JAW磨擦片(硬片)WEAR PLATE镶针CORE PIN波仔螺丝(球头柱塞)BALL-CATCH(BALL PLUNGER)顶针EJECTOR PIN 斜边(斜导柱)ANGLE PIN扁顶EJECTOR BLADE斜边镶件ANGLE PIN INSERT司筒EJECTOR SLEEVE斜边压板COVER方顶（直顶）STRAIGHT EJECTOR行位导轨GUIDE RAIL斜顶LIFTER行位夹SLIDE RETAINER斜顶座HEEL BLOCK推板STRIPPER BLOCK杯头螺丝S.H.C.S加速顶ACCELERATED EJECTOR平头螺丝 F.H.C.S回针RETURN PIN机米螺丝(内六角螺塞 )SCREW PLUG(MINI SCREW)辅针SPRING RETAINER山打螺丝SHOULDER BOLT水口钩针SUCKER PIN螺栓拉杆STOPPER BOLT螺孔拉杆PULLER BOLT上码模板TOP CLAMP PLATE水口推板RUNNER STRIPPER PLATE铜堵头BRASS PLUGA板 A PLATE喉咀MALE PLUG推板STRIPPER PLATE加长喉咀EXTENSION PLUGB板 B PLATE集水块(集流板)WATER MANIFOLD托板SUPPORT PLATE水塘(隔水片)BAFFLE方铁SPACER PLATE水管BUBBLER TUBE面针板EJECTOR RETAINER PLATE密封圈("O"令)"O"RING底针板EJECTOR PLATE下码模板BOTTOM CLAMP PLATE油缸HYDRAULIC CYLINDER隔热板INSULATOR SHEET气阀AIR POPPET VALVE气针GAS PIN替换镶件INTERCHANGEABLE INSERT日期镶件DATING INSERT弹簧（弹弓）SPRING 环保镶件RECYCLING INSERT吊环SAFETY HOIST RING铜镶件COPPER INSERT早回EARLY RETURN铍铜镶件BeCu INSERT撑头SUPPORT PILLAR行程开关SWITCH垃圾钉STOP PIN计数器COUNTERK.O接头K.O.ADAPTER限位块STOPPER疏气镶件SINTERED VENT扣机LATCH LOCK拉板PULL PLATE开闭器(拉模扣）PARTING LOCK热流道板HOT RUNNER MANIFOLD齿轮GEAR热咀HOT SPRUE BUSHING齿条RACK单车链CHAIN齿轴PINION SHAFT。
模具中英文对照(整理)
工程部 / Design department:1) Designer - 设计师。
2) Assembly drawing - 模具组装图。
3) Mold layout - 模具结构图。
4) 2D product drawing - 2D产品图。
5) 3D product data - 3D产品数据。
6) Part drawing - 散件图。
7) Insert molding - 镶件模。
8) 2 color mold / Double injection tool - 双色模。
9) Hydraulic system - 油/水压系统。
10) Parting line - 分模线。
11) Air venting - 排气槽。
12) Cooling system - 冷却系统。
13) Screw - 镙丝。
14) Hot runner system - 热流道。
15) Valve gate - 伐针入水口。
16) Fan gate - 扇型入水口。
17) Pin point gate - 针点进胶。
18) Moon gate / Banana gate - 香蕉，象牙入水口。
19) Submarine gate - 潜水口。
20) Injection machine tonnage - 注塑机吨数。
21) Number of cavity - 穴数。
22) Steel - 钢材。
23) Copper - 铜。
24) Tungsten copper - 钨铜。
25) Beryllium copper - 铍铜。
26) Hardening - 加硬/淬火。
27) Tempering - 回火。
28) Chroming - 电镀。
29) Painting - 喷漆。
30) Resin - 胶材。
31) Printing - 丝印。
32) Texturing - 嗮纹/咬花。
33) Socket screw - 带肩镙丝。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
英文名 accelerator aging back pressure breathing cell-forming agent charge clamping frame compressor cooling fixture de-gassing expanding agent foaming agent gelling glass mat gloss heating element land moulding cycle mould parting line platform polymerization polystyrene beads pre-expand promotor regrind regrind material release agent rotation spindle roving seamless solidify spray gun squeegee steam jacket surge tank transfer chamber vacuume pump vent mould stripping polish grin lathe mill wire cut
中文名 滾壓 離心澆鑄 冷模圕 浸漬模圕 雙色模圕 垂幕式成型 包封,包裝,封裝 發泡模圕 纏絲法 鍛制 嵌件模型 相配模圕 相配模成型 熔體滾筒涂層 膠漿澆鑄 圔杆式真空成型 粉涂層 預混模圕 壓力袋模圕 旋轉模圕，搪膠 增強 膠漿模圕 壓傳涂層 真空袋模圕 真空驟縮成型 網架浸漬 預接待室 鎖模扣 拉針 油坑 薄鋼 模架 噴油 絲印 水路
電阻焊接 固定圈 螺絲批 點焊 彈簧夾 彈簧墊圈 雙頭螺栓 轉矩扳鉗 觸針 超聲焊接
resistance welding retaining ring screw driver spot welding spring clips spring washer stud torque wrench welding horn ultrng 浸漬透過 blister 起泡 bubble 氣泡 burned 焦印 chalking 粉化 clear patches 斑點 crack 裂紋 discolouration 變色作用 filler specks 填料斑點 fines 粉料 fisheyes 魚眼 flash 溢料 frosting 起霜 haze 霧狀 orange peel 橘皮狀 pimple 起小粒 pinhole 針孔 porosity 多孔性 scratch 刮痕 splashing 水漬 weld line 接合線 stamping machine 熱壓印機 transer moulding machine 壓傳模圕機 vacuume metallizer 真空鍍金機 ejector system layout guaranteed tool life spare part requested tech point checklist parting line gating point cavity marking date code 12NC marking mould marking sub-contracting item sketch finishing 2 plate mould combined tool 頂針系統 排位 制模公司保証啤數 后補件 工程提點 分模線 水口點 頭號 日期指示印 12N印 模編號 外判加工 草圖 表面處理 2板模 合作模