管道阀门材料的英文代码
阀门专业术语中英文对照
阀门专业术语中英文对照1.缩写词和代号1.1 法兰结构形式及密封面代号BL---Blind Flange法兰盖LF/SE---Lapped Joint Flange对焊环松套法兰SO---Slip-On Welding Flange带颈平焊兰SW---Socket Welding Flange承插焊法兰Th---Thread Flange螺纹法兰WN---Welding Neck Flange带颈对焊法兰FF---All Flat Face全平面RF---Raised Face突面FM---Female Face凹面M---Male Face凸面T---Tongue Face榫面G---Groove Face槽面RJ---Ring Joint环连接面1.2 常用缩写词 `13Cr + STL---13Cr Trim with Stellited Seat DWD---Split Wedge Disc楔形双闸板MFR'S---Manufacturer's Standard 制造厂标准RWD---Resilient Wedge Disc弹性闸板13Cr阀芯带STL阀座"ENP---Electroless Nickel Plating 镍磷硼合金镀层NBR---Nitrile-butadiene Ruber丁腈橡胶Sch.No.---Schedule Number管表号Bana-N丁钠橡胶FE---Flanged End法兰连接端NPS---Nominal Pipe Size 管子公称尺寸（英制）STL---Stellited硬质合金（钴－铬－钨合金）BB---Bolted Bonnet螺栓连接的阀盖FLG---Flange法兰NPT---National Pipe Taper Thread 60°锥管螺纹SWD---Solid Wedge Disc楔形单闸板BC---Bolted Cap螺栓连接的阀帽FS---Forged Steel锻钢NRS---Non-Rising Stem暗杆SW----Socket Weld承插焊BN---Bayonet 卡套连接FWD---Flexible Wedge Disc 挠性楔形闸板OS---Outside Screw外螺纹TB---Thread Bonnet螺纹阀盖BRZ---Bronze青铜GALV---Galvanized 镀锌OS&Y---Outside Screw with Yoke外螺纹带支架TE---Thread End螺纹端BW---Butt Weld对焊连接HEX—六角头（螺栓）PTFE---Polytetrafluoroethylene聚四氟乙烯TC---Thread Cap 螺纹阀帽CI---Cast Iron铸铁HF---Hard Face硬表面RTFE---Reinforced PTFE增强PTFEWB---Welded Bonnet焊接阀盖CS---Carbon Steel碳钢HW---Handlewheel手轮缩写说明BE坡口BW对焊BL法兰盖BC.SWING螺栓阀盖旋启式BB.OS&Y螺栓阀盖外螺纹及轭式BC.LIFT螺栓阀盖升降式Dual-plate双蝶板FB.L.OP.全通径手工操作FB.GEAR OP.全通径齿轮操作FF全平面FL法兰F锻件GV镀锌HF硬质合金堆焊LJ活套法兰L翻边短节短规格LL翻边短节长规格MFR'S.ST'd制造商标准NPT螺纹(60O)PE平口PTFE聚四氟乙烯RPTFE增强聚四氟乙烯RF突面STR过滤器SM无缝STL硬质合金SW承插SO平焊Sch管道壁厚标号SB.ISRS螺纹阀盖内螺纹明杆ISNS内螺纹暗杆WL焊接WN带颈对焊WFR对夹Y2半硬不锈钢焊管专业名称中英文对照（一）锅炉热交换器用不锈钢钢管：stainless steel tube for boiler，heat – exchanger 材质：grade外径：OD焊接方式：welding method包装方式：packing标准：standard壁厚：wt产品应用：application捆包木箱包装：bundle or wooden case规格：specification薄壁不锈钢水管：light gauge stainless steel water pipes食品卫生不锈钢管：stainless steel sanitary tubes开卷 uncoiling活塞 loop成型 forming焊接 welding内外焊缝整平 outside inside weld bead rolling预矫正 precalibration感应热处理：induction heat treating定径矫直 sizing straightening涡流检测 eddy current test喷码 marking切断 cutting水压检查 hydrostatic test水下气压测试 under water air pressure testX射线检查 X ray inspection酸洗 pickling最终检查 final inspection发运 shipping光亮退火 bright annealing尺寸检测 dimention examination表面质量 surface examination液压试验 hydrostatic test气压测试 pneumatic test硬度测试 harness test金相组织测试分析 metallographic examination晶间腐蚀测试 intergranular corrosion test机械性能测试 mechanical property test拉伸试验 tension test压扁试验 flattering testASTM 标准下不锈钢焊管A249 关于奥氏体广泛用于热交换器，锅炉，过热器，冷凝器的焊管A269 一般用途用无缝和焊接的奥氏体不锈钢管制品标准A270 奥氏体铁素体无缝管卫生管A554 机械用焊管ASTM命名方法及扩充 (以ASTM A249为例):其中在ASTM标准下，分别有以A.B.C为首字母A：ferrous material 亚铁含铁材料黑色金属材料B：non—ferrous materials 不含铁材料有色金属材料C: cementitious materials 胶结材料ASTM A249 在A248 出版之后发展，分配可以用数字，在A25.0出现之前没有实际意义。
常用管道、阀门、材料中英文名称对照概述
目录1 管道组成件Piping component (1)1.1 管子Pipe (1)1.2 管件Fitting (2)1.3 弯管Bend (3)1.4 法兰Flange (FLG） (4)1.5 垫片Gasket (GSKT) (5)1.6 阀门Valve (6)1.7 管道特殊件Piping Specialty (10)1.8 端部连接End Connection (12)1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet) 异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head) 45°斜三通45° lateral45°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run)45°斜三通(一个直通口及支管为异径) 45° lateral (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet) 异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss管接头coupling, full coupling半管接头half coupling异径管接头reducing coupling活接头union内外螺纹缩接（俗称补芯）bushing管帽cap (C)堵头plug短节nipple异径短节reducing nipple; swage nipple1.3 弯管Bend预制弯管fabricated pipe bend跨越弯管（^ 形）cross-over bend偏置弯管（~ 形）offset bend90°弯管quarter bend环形弯管cirele bend单侧偏置90°弯管（? 形）single offset quarter bendS形弯管“S” bend单侧偏置U形膨胀弯管（| ?形）single offset “U” bendU形弯管“U” bend双偏置U膨胀弯管double offset expansion “U” bend斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange (FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange (SO); slip-on welding flange 承插焊法兰socket welding flange松套法兰lap joint flange (LJF)对焊法兰welding neckflange (WNF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar （与stub end相似）平焊环welding-on collar突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating法兰密封面，法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face槽面groove face环连接面ring joint face全平面；满平面flat face; full face (FF)光滑突面smooth raised face (SRF)法兰面加工facing finish粗糙度roughness光滑的smooth齿形serrated均方根root mean square (RMS)算术平均粗糙高度arithmetical average roughness height (AARH)配对法兰companion-flange螺栓圆bolt circle (B.C.)1.5 垫片Gasket (GSKT)垫片的型式type of gasket平垫片flat gasket环形平垫片flat ring gasket平金属垫片flat metal gasket夹棉织物的橡胶elastomer with cotton fabric insertion夹石棉织物的橡胶elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶elastomer with asbestos fabric insertion and with wire reinforcement无石墨压缩白石棉垫片non graphited compressed white asbestos gasket天然白橡胶垫片natural white rubber gasket压缩石棉垫片compressed asbestos class gasket浸聚四氟乙烯的石棉垫片PTFE impregnated asbestos gasket夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler内环inner ring外环，外定位环outer ring波纹金属垫片corrugated metal gasket波纹金属包嵌石棉垫片corrugated metal gasket with asbestos inserted双夹套波纹金属包石棉垫片corrugated metal double jacketed asbestos filled gasket 双夹套垫片double jacketed gasket金属包石棉平垫片flat metal jacketed asbestos filled gasket整体金属齿形垫片solid metal serrated gasket槽形金属垫片grooved metal gasket环形连接金属垫片ring joint metal gasket八角环形垫片octagonal ring gasket椭圆环形垫片oval ring gasket透镜式垫片lens gasket非金属垫片non-metallic gasket1.6 阀门Valve1.6.1 阀门结构、零件阀轭yoke外螺纹阀杆及阀轭outside screw and yoke (OS & Y) 阀杆stem内螺纹inside screw (IS)阀轭套yoke sleeve阀杆环stem ring阀座valve seat (body seat)阀座环、密封圈seat ring整体（阀）座integral seat堆焊（阀）座deposited seat阀芯（包括密封圈、杆等内件）trim阀盘disc阀盘密封圈disc seat阀体body阀盖bonnet阀盖衬套bonnet bush螺纹阀帽screw cap螺纹阀盖screw bonnet螺栓连接的阀盖bolted bonnet (BB)活接阀盖（帽）union bonnet (cap)螺栓连接的阀帽bolted cap (BC)焊接阀盖welded bonnet (WB)本体阀杆密封body stem seal石棉安全密封asbestos emenen seal倒密封back seal压力密封的阀盖pressure-tight bonnet动力操纵器powered operator电动操纵器electric motor operator气动操纵器pneumatic operator液压操纵器hydraulic operator快速操纵器quick-acting operator滑动阀杆sliding stem正齿轮传动spur gear operated伞齿轮传动bevel gear operated扳手操作wrench operated链轮chain wheel手轮hand wheel手柄hand lever (handle)气缸（或液压缸）操纵的cylinder operated链条操纵的chain operated等径孔道full bore; full port异径孔道reducing bore, reduced port,venturi port短型short pattern紧凑型（小型）compact type笼式环lantern ring压盖gland阀杆填料stem packing阀盖垫片bonnet gasket升杆式（明杆）rising stem (RS)非升杆式（暗杆）non-rising stem (NRS)指示器/限位器indicator/stopper注油器grease injector可更换的阀座环renewable seat ring1.6.2 常用阀(1）闸阀gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸扳flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀through conduit gate valve(2) 截止阀globe valve球心型阀盘globe type disc塞型阀盘plug type disc可转动的阀盘swivel disc(3) 节流闪阀throttle valve针阀needle valve(4) 角阀angle valve(5) Y型阀（Y 型阀体截止阀）Y-valve (Y-body globe valve)(6) 球阀ball valve三通球阀3-way ball valve装有底轴的trunnion mounted耐火型fire safe type浮动球型floating ball type防脱出阀杆blowout proof stem(7) 蝶阀butterfly valve对夹式（薄片型）wafer type凸耳式lug type偏心阀板蝶阀offset disc burerfly valve; eccentric butterfly valve 斜阀盘蝶阀canted disc butterfly valve连杆式蝶阀link butterfly valve8) 柱塞阀piston type valve(9) 旋塞阀plug valve三通旋塞阀three-way plug valve四通旋塞阀four-way plug valve旋塞cock衬套旋塞sleeve cock(10) 隔膜阀diaphragm valve橡胶衬里隔膜阀rubber lined diaphragm valve直通式隔膜阀straight way diaphragm valve堰式隔膜阀weir diaphragm valve(11) 夹紧式胶管阀pinch valve（用于泥浆、粉尘等）(12) 止回阀check valve升降式止回阀lift check valve旋启式止回阀swing check valve, flap check valve落球式止回阀ball check valve弹簧球式止回阀spring ball check valve双板对夹式止回阀dual plate wafer type check valve无撞击声止回阀non-slam cheek valve底阀foot valve切断式止回阀stop check valve; non-return valve活塞式止回阀piston check valve斜翻盘止回阀tilting disc check valve蝶式止回阀butterfly check valve1.6.3 其它用途的阀安全泄气阀safety valve (SV)安全泄液阀relief valve (RV)安全泄压阀safety relief valve杠杆重锤式lever and weight type引导阀操纵的安全泄气阀pilot operated safety valve复式安全泄气阀twin type safety valve罐底排污阀flush-bottom tank valve电磁阀solenoid valve, solenoid operated valve电动阀electrically operated valve, electric-motor operated valve气动阀pneumatic operated valve低温用阀cryogenic service valve蒸汽疏水阀steam trap机械式疏水阎mechanical trap浮桶式疏水阀open bucket trap, open top bucket trap浮球式疏水阀float trap倒吊桶式疏水阀inverted bucket trap自由浮球式疏水阀loose float trap恒温式疏水阀thermostatic trap金属膨胀式蒸汽疏水阀metal expansion steam trap液体膨胀式蒸汽疏水阀liquid expansion steam trap双金属膨胀式蒸汽疏水阀bimetallic expansion steam trap压力平衡式恒温疏水阀balanced pressure thermostatic trap热动力式疏水阀thermodynamic trap脉冲式蒸汽疏水阀impulse steam trap放气阀（自动放气阀）air vent valve (automatic air vent valve) （疏水阀用）平板式滑动闸阀slab type sliding gate valve盖阀flat valve换向阀diverting valve, reversing valve热膨胀阀thermo expansion valve自动关闭阀self-closing gate valve自动排液阀self-draining valve管道盲板阀line-blind valve挤压阀squeeze valve（用于泥浆及粉尘等）呼吸阀breather valve风门、挡板damper减压阀pressure reducing valve, reducing valve控制阀control valve膜式控制阀diaphragm operated control valve执行机构actuator背压调节阀back pressure regulating valve差压调节阀differential pressure regulating valve压力比例调节阀pressure ratio regulating valve1.6.4 未指明结构（或阀型）的阀切断阀block valve; shut-off valve; stop valve调节阀regulating valve快开阀quick opening valve快闭阀quick closing valve隔断阀isolating valve三通阀three way valve夹套阔jacketed valve非旋转式阀non-rotary valve排污阀blowdown valve集液排放阀drip valve排液阀drain valve放空阀vent valve卸载阀unloading valve排出阀discharge valve吸入阀suction valve多通路阀multiport valve取样阀sampling valve手动阀hand-operated valve; manually operated valve 锻造阀forged valve铸造阀cast valve（水）龙头bibb; bib; faucet抽出液阀（小阀）bleed valve旁路阀by-pass valve软管阀hose valve混合阀mixing valve破真空阀vacuum breaker冲洗阀flush valve第一道阀；根部阀primary valve根部阀root valve总管阀header valve事故切断阀emergency valve1.7 管道特殊件Piping Specialty1.7.1 管道特殊件（组件）粗滤器strainer过滤器filter临时粗滤器（锥型）temporary strainer (cone type)y 型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器permanent filter丝网粗滤器gauze strainer洗眼器及淋浴器eye washer and shower视镜sight glass阻火器flame arrester喷嘴；喷头spray nozzle取样冷却器sample cooler消声器silencer膨胀节expansion joint波纹膨胀节bellow expansion joint单波single bellow双波double bellow多波multiple bellow压力平衡式膨胀节pressure balanced expansion带铰链膨胀节hinged expansion joint轴向位移型膨胀节axial movement type expansion joint自均衡膨胀节（外加强环）self-equalizing expansion joint 带接杆膨胀节tied expansion joint万向型膨胀节universal type expansion joint球形补偿器ball type expansion joint填函式补偿器slip type (packed type) expansion joint单向滑动填料函补偿器single actionpacked slip joint1.7.2 管道特殊元件Piping Special Element软管接头hose connection (HC)快速接头quick coupling金属软管metal hose橡胶管rubber hose挠性管flexible tube鞍形补强板reinforcing saddles补强板reinforcement pad特殊法兰special flange漏斗funnel排液环drip ring排液漏斗drain funnel插板blank垫环spacer8字盲板spectacle blind; figure 8 blind限流孔板restriction orifice爆破片rupture disk法兰盖贴面protective disc费托立克接头victaulic coupling1.8 端部连接End Connection法兰端flanged end坡口端beveled end (BE)对焊端butt welded end平端plain end (PE)承插焊端socket welding end螺纹端threaded end (TE)承口bell end焊接端welding end法兰连接（接头）flanged joint对焊连接（接头）butt welded joint螺纹连接，管螺纹连接threaded joint, pipe threaded joint 锥管螺纹密封焊连接seal-welded taper pipe threaded joint 承插焊连接（接头）socket welded joint承插连接（接头）bell and spigot joint环垫接头ring joint (RJ)万向接头universal joint软钎焊连接（接头）soldered joint搭接接头，松套连接lapped joint外侧厚度切斜角bevel for outside thickncss内侧厚度切斜角bevel for inside thickness内外侧厚度切斜角bevel for combined thickness法兰式的flanged (FLGD)对焊的butt welded (BW)螺纹的threaded (THD)承插焊的socket welded (SW)小端为平的small end plain (SEP)大端为平的large end plain (LEP)两端平both ends plain (BEP)小端带螺纹small end thread (SET)大端带螺纹large end thread (LET)两端带螺纹both end thread (BET)一端带螺纹one end thread (OET)支管连接branch connection焊接支管branch pipe welded directly to the run pipe37书中横卧着整个过去的灵魂——卡莱尔人的影响短暂而微弱，书的影响则广泛而深远——普希金人离开了书，如同离开空气一样不能生活——科洛廖夫书不仅是生活，而且是现在、过去和未来文化生活的源泉——库法耶夫书籍把我们引入最美好的社会，使我们认识各个时代的伟大智者———史美尔斯书籍便是这种改造灵魂的工具。
美标阀门型号说明
1.4阀门及小型设备代号解释1.4.1闸阀（GATE VALVE）、截止阀（GLOBE VALVE）止回阀（CHECK VALVE）、针型阀（NEEDLE GLOBE VALVE） － / 特殊代码（3位）见表1.4.1-8阀芯材质，见表1.4.1－7阀体材质，见表1.4.1－6连接型式，见表1.4.1－5接管壁厚，见表1.2.1－2*传动机构，见表1.4.1－4结构型式，见表1.4.1－3压力等级，见表1.4.1－2阀门类别，见表1.4.1－1 注*：只有“连接型式”中为BW时才有此项注：每个阀门采用什么标准由“结构型式”确定。
注：←每个阀门选用何种材料的垫片和螺栓、螺母由“阀体材料”确定。
↑对CL900.1500.2500三个等级的阀门，一般采用压力密封阀盖，此时“阀盖垫片”和“阀盖螺栓”项缺省。
→等级1a、2a、3a、4a、5a适用于JB标准阀门。
注：←如果阀门的结构型式为“2”、“8”和“9”，即阀盖为压力密封阀盖，则该表中的“阀盖垫片材料”和“阀盖螺栓材料”栏缺省。
↑如果阀门的结构型式为“5”，则该表中的“阀杆填料”栏缺省。
表1.4.1－8，特殊代码1.4.2球阀（BALL VALVE）特殊代码（3位）见表1.4.1-8阀芯材质，见表1.4.2－2阀体材质，见表1.4.1－6连接型式，见表1.4.1－5接管壁厚，见表1.2.1－2*传动机构，见表1.4.1－4结构型式，见表1.4.2－1压力等级，见表1.4.1－2阀门类别：球阀/BALL VALVE，代号－Q1.4.3 旋塞阀(PLUG VALVE)阀芯材质，见表1.4.3－2阀体材质，见表1.4.1－6连接型式，见表1.4.1－5接管壁厚，见表1.2.1－2*传动机构，见表1.4.1－4结构型式，见表1.4.3－1压力等级，见表1.4.1－2阀门类别：旋塞阀/PLUG VALVE，代号－P1.4.4 蝶阀(BUTTERFLY VALVE)阀芯材质，见表1.4.4－2阀体材质，见表1.4.1－6连接型式，见表1.4.1－5接管壁厚，见表1.2.1－2*传动机构，见表1.4.1－4结构型式，见表1.4.4－1压力等级，见表1.4.1－2阀门类别：蝶阀/BUTTERFLY VALVE，代号－D1.4.5 疏水阀(STEAM TRAP VALVE)阀芯材质，见表1.4.5－2阀体材质，见表1.4.1－6连接型式，见表1.4.1－5结构型式，见表1.4.5－1压力等级，见表1.4.1－2阀门类别：疏水阀/STEAM TRAP VALVE，代号－S1.4.6 过滤器(STRAINER)阀体材质，见表1.2.1－3连接型式，见表1.4.1－5接管壁厚，见表1.2.1－2*结构型式，见表1.4.6－1压力等级，见表1.3.1－2阀门类别：过滤器(STRAINER)，代号－T阀芯材质一般为304。
管道专业常用的英文及缩写词.
北京石油化工设计院体系文件管道专业常用的英文及缩写词BPDI BE321321-05l 范围本文件规定了管道专业在设计文件上常用的英文及缩写词,在设计文件中使用的其它专业缩写词应按相关专业的规定执行。
本文件适用于管道专业的设计工作。
2 说明本文件编制目的是为了统一用词和词的缩写,使设计文件的用词统一、规范并推荐在图纸上采用英文缩写词,尽量减少使用汉字,以利于国际交流。
文字说明和资料翻译时,应使用本规定的英汉对照词。
3 按中文分类排列汉语词英语词英语缩写3.1 阀门类3.1.1常用阀闸阀截止阀(球心阀)节流阀针型阀角阀(角式截止阀) Y型阀(Y型截止阀) 球阀三通球阀蝶阀柱塞阀旋塞阀三通旋塞阀四通旋塞阀旋塞隔膜阀夹紧式胶管阀止回阀Gate valveGlobe valveThrottle valveNeedle valveAngle valveY-valve(Y-boby globe valve)Ball valve3-Way ball valveButterfly valvePiston type valvePlug valve3-Way ball valve4-Way ball valveCockDiaphragm valvePinch valveCheck valveTRV汉语词英语词英语缩写北京石油化工设计院2005—7—26批准2005—8—15实施3.1.2其它阀安全泄汽阀(安全阀) 安全泄液阀(卸荷阀) 安全泄压阀罐底排污阀波纹管密封阀电磁阀电动阀气动阀低温用阀蒸汽疏水阀呼吸阀减压阀控制阀调节阀3.1.3不表明结构的阀切断阀手动控制阀调节阀快开阀隔断阀三通阀夹套阀排污阀排液阀放空阀卸载阀排出阀吸入阀多路阀取样阀手动阀旁路阀冲洗阀根部阀底阀3.2 管子与连接3.2.1管子管子(标准规格)管子(非标规格)钢管铸铁管衬里管复合管(包复金属管) Safety valveRelief valveSafety relief valveFlush-bottom tank valveBellow sealed valveSolenoid valveElectrically operated valvePneumatic operated valveCryogenic service valveSteam trapBreather valveReducing valveControl valveBlock valve, Shut-off valve ,Stop valveHand control valveRegulating valveQuick opening valveIsolating valve3-Way valveJacketed valveBlow down valveDrain valveVent valveUnloading valveDischarge valveSuction valveMultiport valveSampling valveHand operated valve, Manually operated valveBy-pass valveFlush valveRoot valve, Primary valve, Header valveFoot valvePipeTubeSteel pipeCast iron pipeLined cining pipeClad pipeSVTRVHCVVTV汉语词英语词英语缩写碳钢管合金钢管不锈钢管奥氏体不锈钢管铁素体合金钢管]无缝钢管焊接钢管镀锌钢管水煤气钢管塑料管玻璃管橡胶管壁厚系列号(管子表号) 壁厚3.2.2管子零件弯头异径弯头长半径弯头短半径弯头180°弯头(回弯头) 三通(T型三通)异径三通等径三通45°三通正三通(Y型三通)四通(十字通)异径管(大小头)同心异径管偏心异径管支管连接支管台(凹台)活接头管接头(管箍)管帽短节(短管)管堵(丝堵)焊接管帽盲板,管道盲板8字盲板特殊管件3.2.3连接对焊的法兰的Carbon steel pipeAlloy steel pipeStainless steel valveAustenitic stainless steel pipeFerric alloy steel pipeSeamless steel pipeWelded steel pipeWater gas steel pipeGalvanized steel pipePlastic pipeGlass tubeRubber tubeSchedule numberWall thicknessElbowReducing elbowLong radius elbowShort radius elbowReturn elbowTeeReducing teeStraight tee45°LateralTrue “Y”CrossReducerConcentric reducerEccentric reducerBranch connectionBossUnionCouling, Full couplingCapNipplePlugWelded capBlank, Blind, Line blankSpectacle blankSpecial pipe fittingsButt weldedFlangedSch.NoW.TLRESREREDCONECCCNIPPLGWCL.BS.PBWFLGD汉语词英语词英语缩写螺纹的承插焊的承插的对焊连接法兰连接螺纹连接管螺纹连接承插焊连接承插连接,套筒连接整体法兰螺纹法兰承插焊法兰松套法兰对焊法兰平焊法兰板式平焊法兰松套板式法兰滑套法兰(平焊法兰)法兰盖孔板法兰异径法兰螺栓圆直径法兰面光面,光滑面突面凹凸面凸面凹面榫槽面榫面槽面环连接面,梯型槽密封面全平面,满平面光滑突面螺栓热紧螺栓冷紧螺纹管帽螺纹焊管座承插焊管帽承插焊管座垫片非金属包覆垫片ThreadedSocket weldedBelledButt welded jointFlanged jointThreaded jointPipe threaded jointSocket welding flangeBell and spigot jointIntegral pipe flangeThreaded flangeSocket welding flangeLap joint flangeWeld neck flangeSlip on flange, Slip on weld flangeWelding plate flangeLoose plate flangeSlip-on-welding flangeBlind flange, BlindOrifice flangeReducing flangeBolt circle diameterFlange facing, facing of flangePlain faceRaised faceMale-female(Seal contact)faceMale faceFemale faceTongue groove faceTongue faceGroove faceRing joint faceFlat face, Full faceSmooth raised faceBolt hot tighteningBolt cold tighteningThread capThread letSocket welded capSocket welded letGasketNon-metallic jacked gasketTHDSWBWTSWTHDFLJFWNFBCDFOFPFRFMFMMFFMFTGFTFGFRJFFFSRFTHDCTHLETSWCSWLET汉语词英语词英语缩写金属包覆垫片缠绕式垫片内环外环金属垫片3.3 管道附件3.3.1组件气液分离器阻火器临时粗滤器永久粗滤器(固定粗滤器) Y型粗滤器T型粗滤器网状粗滤器粗滤器过滤器永久过滤器消音器(消声器)视镜浮球式视镜全视镜取样冷却器喷嘴,喷头喷射器洗眼器膨胀器(伸缩接头)波纹膨胀节球型补偿器填函式补偿器安全淋浴器3.3.2元件排液漏斗漏斗爆破板限流孔板混合孔板软管接头金属软管橡胶管挠性管(柔性管)快速接头旋转接头Metallic jacket gasketSpiral wound gasketInner ringOuter ringMetallic gasketGas-liquid separationFlame arrested(Flame trap)Temporary strainetPermanent strainetY-type strainerT-type strainerGauge strainerStrainerFilterPermanent filterSilencerSight glass(Sight flow glass)Floating ball sight flow indicatorFull view sigh flow indicatorSample coolerSpray nozzleEjectorEye washerExpansion jointBellow expansion jointBall type expansion jointSlip type(packed type)expansion jointSafety showerDrain funnelFunnelRupture diskRestriction orificeMixing orificeHose connectionMetal hoseRubber hoseFlexible hoseQuick couplingSwivel jointE.WS.SRPROHC汉语词英语词英语缩写减压器3.4材料3.4.1 金属材料碳钢合金钢合金结构钢工具钢不锈钢奥氏体不锈钢马氏体不锈钢锻钢铸钢铸铁灰铸铁可锻铸铁球墨铸铁高硅铸铁铝铜黄铜铝镁合金蒙乃尔合金(镍铜合金)钛铅型钢角钢槽钢工字钢(工字梁)宽翼线工字钢(H钢)T字钢方钢扁钢园钢钢带钢板网纹钢板3.4.2非金属材料塑料丙烯晴、丁二烯、苯乙烯橡胶聚乙烯聚氯乙烯ReducerCarbon steelAlloy steelStructural alloy steelTool steelStainless steelAustenitic stainless steelMartensitic stainless steelForged steelCast steelCast ironGrey cast ironMalleable ironNodular cast iron, Nodular cast graphite ironHigh silicon cast ironAluminumCopperBrassAluminum magnesiumMonelTitaniumLeadShaped steelAngle steelChannelI—BeamWide flanged beamT—BarSquare BarFlat BarRound steel, rodStrap steelPlateCheckered platePlasticAcrylonitrile-butadiene-styrene rubberPolyethylenePloy vinyl chlorideREDC.SS.SC.IM.IABSPEPVC汉语词英语词英语缩写氯化聚氯乙烯聚丙烯聚苯乙烯氯化聚醚聚碳酸酯有机玻璃聚四氟乙烯碳纤维聚三氟氯乙烯氯化聚乙烯氯磺化聚乙烯环氧树脂泡沫聚苯乙烯玻璃纤维增强聚酯丁腈橡胶氯丁橡胶天然橡胶丁基橡胶丁苯橡胶顺丁橡胶不饱和聚酯聚氨酯耐火砖陶瓷搪瓷石棉3.5 设备安装3.5.1布置装置边界边界内边界外中心线接续线设备布置标高,高程,立面图绝对标高坐标坐标原点装置北真实北方位危险区Chlorinated ploy vinyl chloridePoly propylenePolystyreneChlorinated polyetherPolycarbonatePoly methyl methacrylatePolytetrafluoroethleneCarbon fiberPoly chlorotrifluoroethyleneChlorinated poly ethyleneChlorosulfonated polyethyleneEpoxy resinExpanded poly styreneGlass fiber reinforced polyesterNitride butadiene rubberNeoprene rubberNatural rubberButyl rubberStyrene-Butadiene rubberCis-polybutadiene rubberUnsaturated polyesterPolyurethaneFire brickCeramicPorcelain enamelAsbestBattery limitInside battery limitOutside battery limitCenter lineMatch lineEquipment arrangement; Equipment layout; Plot PlanElevationAbsolute elevationCoordinateOrigin of coordinatePlant northtrue northOrientationHazardous areaCPVCPPPSCPEPCPMMAPTFECARPCTFECPE;CMCSM;CSPREPEPSFRPNBRNRPIBISBRCBRUPPUB.LL.S.B.LO.S.B.LM.LELTN汉语词英语词英语缩写铺砌区非铺砌区楼面地面标高平台场地管廊电缆槽(架) 建筑物钢结构基础柱梁桁架墙篦子板吊装孔吊梁架顶面钢结构顶面混凝土顶面梁顶面板表面吊勾顶面,上面底面,底下支撑点固定点建筑北设计北电缆沟管沟明沟明火地点散发火花地点防火间距支架间距地面坡度吊装孔道路地面内径外径汉语词Paving areaUnpaving areaFloorGround levelPlatformYardPipe rackCable tray(channel)BuildingSteel structureFoundationColun ; Post; StanchionBeamGirderWallGrate; GratingErection openingHoisting beamTop of supportTop of steelTop of concreteTop of BeamPlat faceHookTopBottomPoint of supportFixed pointConstruction northDesign northElectric cable duct; Electrical trenchPipe trenchOpen trenchOpen fire placeSend-out spark placeFire protection spacingSupport spacingGround gradeErection openingRoadGround; Ground levelInside DiameterOutside Diameter英语词GLPFHBTOSTOSTOCTOBPLATFTOPBOTPOSFPDNGRDIDOD英语缩写公称直径公称压力切线中心线门窗地下底板底面控置室分析室配电室变压器室通风室更衣室贮藏室维修室盥洗室,厕所办工室门卫室,传达室接待室,会客室地秤室泵房压缩机室电池室消防栓电气盘仪表盘就地盘3.5.2设备塔洗涤塔吸收塔冷却塔精馏塔换热器空冷器水冷却器冷却器螺旋板换热器套管换热器石墨换热器板片换热器汉语词Nominal diameter; Nominal(pipe)sizeNominal pressureTangent lineCenter lineGateWindowUnder groundBottom of base plateControl roomAnalyzerSubstationTransformer roomVentilation roomLocker roomStorage roomMaintenance roomCloste ; Toilet; WashroomOfficeEntrance guard room; Janito r′s roomReception roomWeigh-bridge roomPump house; Pump roomCompressor house(room)Battery roomFire plugElectrical panelInstrument panelLocal panelTower; ColumnScrubberAbsorberCooling towerFractionating towerHeat exchangerAir coolerWater coolerCondenserSpiral plate exchangerDouble pipe heat exchangerGraphite heat exchangerPlate type heat exchanger英语词DNPNTLUGBBPW.CFPL英语缩写板翅式换热器板式塔填料塔浮阀塔反应器贮罐缓冲器混合罐浮顶罐内浮顶罐固定顶罐卧式储罐球罐罐,鼓,筒,桶气柜螺旋式气柜湿式气柜干式气柜离心泵涡轮泵旋涡泵转子泵齿轮泵内啮合齿轮泵螺杆泵柱塞泵双作用往复泵计量泵,定量泵泥浆泵管道泵手摇泵深井泵输送泵屏蔽泵液下泵潜水泵多级泵立式泵磁力泵气动泵轴流泵混流泵Plate-fin heat exchangerPlate towerFloating distillation towerValve towerReactorTankKnock-out drumMixing tank(drum)Floating roof tank; Pontoon roof tankFloating internal roof tankStationary roof tankHorizontal tankSpheroid; Spherical tankDrumGas holderHelical gas-holderWet gas holderDry gas-holderCentrifugal pumpTurbine pumpV ortex pumpRotary pumpGear pumpInternal gear rotary pump; Crescen gear pump Screw pumpPlunger pumpDouble action reciprocating pumpMetering pumpSlurry pump; Sludge pump; Mud pumpInline pumpHand pump; Wobble pumpDeep well pumpTransfer pump; Delivery pumpShielding can-type pump; Canned pump Submerged pump; Submersible pumpSubmerged pump; Immersible pumpStage pump;, Multistage pumpVertical pump;Magnetic transmission pump; Magnetic coupled pump Pneumatic pumpAxial flow pumpMixed flow pump汉语词英语词英语缩写陶瓷泵陶制泵自吸泵消防泵真空泵叶片式真空泵水环式真空泵(压缩机) 液环泵(压缩机)活塞式压缩机螺杆压缩机离心压缩机多级压缩机往复式压缩机风机,风扇鼓风机离心机离心分离机离心过滤机压滤机板框式压滤机厢式压滤机带式过滤机转鼓式过滤机盘式过滤机板式塔填料塔浮阀塔带式(皮带)运输机螺旋输送机加热器搅拌器炉子烟囱火炬锅炉发电机汽轮机电动机起重机,吊车板式起重机Ceramic pumpStoneware pumpSelf suction pump; self priming pumpFire pumpVacuum pumpVane vacuum pumpWater ring vacuum pump(compressor)Liquid ring pump(compressor)Piston compressorHelical screw compressorCentrifugal compressorMultiple stages compressorReciprocating compressorFan; VanBlowerCentrifugerCentrifugal separatorCentrifugal filterPressure filterPlate and frame filter pressBox type filer pressBelt filterRotating drum type filterTray filterPlate towerPack tower; Packed columnValve tower; Floating distillation towerRibbon conveyer; Belt conveyerScrew convery ; Spirla conveyer; Worm conveyerHeaterAgitatorFurnaceStackFlareBoilerGeneratorSteam turbineMotorGraneBridge crane汉语词英语词英语缩写吊车梁电动葫芦成套设备附属设备,附件干燥器混合器蒸发器萃取器结晶器澄清器喷射器喷头分离器旋风分离器,旋风除尘器布袋收尘器电除尘器除尘器,吸尘器振动筛破碎机颚式破碎机粉碎机,磨碎机提升机,卷扬机斗式提升机电梯泡沫站软管站3.6 管道布置3.6.1设计文件管道布置管道布置平面管道研究“X”视图“A-A”视图详图轴测图,空视图索引图接续图管道及仪表流程图工艺控制图工艺流程图汉语词Crane beam; Hoist beamMotor hoist; Electric hoist; Electric blockPackage unitAttachment equipmentDryerMixerEvaporatorExtractorCrystalligerGravity settlerEjectorSprayerSeparatorCyclone; Cyclone separator deviceCloth envelop collectionElectrostatic precipitator; Electridust precipitatorDuster; Dust arresterVibrating screen; Riddler; Oscillating sieveBreaker; Cracker mill; Crusher; Crushing millJaw breaker ;Jaw crusher; AlligatorGrinder; Pulverizer; Disintegrator; AtomizerHoister; Lifter; Gig; ElevatorBucket elevatorElectrical lift; ElevatorFoam stationHose stationDesign documentPiping assembly; Piping layoutPiping arrangement planPiping studyView“x”Section“A-A”Detail drawingIsometric drawingKey planContinue on drawingPiping and Instrument diagramProcess control diagramProcess flow diagram英语词H.SPAPCODP&ID英语缩写公用工程流程图总图总平面布置图放大图节点地上地下地面附图草图图例符号比例蒸汽伴管热水伴管电伴热夹套管高压中压低压大气，大气压工作压力，操作压力设计压力工作温度，操作温度设计温度管口取样接口清除口，清洗口排出口出口入口连接，接头管口方位排液放空污水坑，污水池地坑，井地漏下水管人孔手孔关闭后加铅封（封关）开启后加铅封（封开）汉语词Utility flow diagramGenera planGeneral arrangement planEnlarged viewNodeAbove groundUnder groundGroundFigueSketchLegendSymbolScaleSteam tracingHot—water tracingElectrical tracingJacketed tracingHigh pressureMedium pressureLow pressureAtmosphereOperating pressure; Working pressureDesign pressureOperating temperatureDesign temperatureNozzleSampling connectionClean outExhaustOutlet; DischargeInlet; suctionConnectionNozzle orientationDrainVentSump pitPitFloor drainSewerManholeHandholeCar seal closeCar seal open英语词UFDAGUGGRDH.P.M.P.L.P.ATMS.CC.ODISCHINLETVENTF.DM.HH.HC.S.CC.S.O英语缩写关闭后加锁（锁关）开启后加锁（锁开）正常时关闭正常时开启故障时关闭故障时开启垂直，正交平行管顶管底管内底底平顶平水平的，卧式的立式的，垂直的水平安装垂直安装管件直连管间距管道跨距管道等级管道材料规定等级分界隔热分界管道附件管道元件面至面中心至面中心至中心中心至端面坡度公称直径公称压力外径内径螺栓圆直径软管接头管段，短管可拆短管直管弯管管内底标高汉语词Locked closedLocked openNormally closedNormally openValve closes on failure of actuating energyValve opens on failure of actuating energyPerpendicularParallelTop of pipeBottom of pipeInvert, Inside bottom of pipeFlat on bottomFlat on topHorizontalVerticalHorizontal installationVertical installationFitting to fittingLine spacingLine spanPiping classPiping material specificationMaterial Specification breakInsulation breakPiping attachmentPiping elementFace to FaceCenter to FaceCenter to CenterCenter to EndSlope; GradeNominal DiameterNominal pressureOutside DiameterInside DiameterBolt circleHose connectionSpool piece; SpoolRemovable joint spoolRun pipe; Straight pipeBendInvert elevation英语词L.CL.ON.CN.OFCFOTOPBOPINVFOBFOTHORVERTFTFF-FC-FC-CC-EDNPNODIDB.CHCRSPIE英语缩写不许出现袋形孔板孔，洞开孔低点标高低点高点平台袋形管外壳3.6.2 管道安装管托管卡管架支耳U型卡带状卡托座吊耳导向板,夹板底板顶板予埋件支承环加强板垫片(垫平用)锚固件预焊件(设备上) 聚四氟乙烯滑动板连接板连接杆限制杆鞍座裙座支承架滑动架固定架导向架吊架弹簧架弹簧托汉语词Not allow pocketOrifice plateHoleCaving holeLow point elevationLow pointHigh pointPlatform; Flat; Floor; Surface plateBag-Shape pipe(outside)Shell; Case(shell);Casing; CoverShoeClampPiping supportLugCleviceStrap clampStoolEarCleatBase plateTop plateEmbedded part; Inserted plateRingStiffenerShimClipClip(on equipment)PTFE sliding plateTie plateTie rodLimit rodSaddleSkirtResting supportSliding supportAnchorGuideHangerSpring supportResting type spring support英语词NO.PC.HLP.LELPHPPF英语缩写弹簧吊架恒力吊架滚动支架减振器悬臂架三角架支腿N型管架L型管架柱式管架墙架管墩,低管架特殊管架(予埋螺栓)伸出长度对中心,找正跨度力矩弯矩扭矩荷载反力位移角位移冷紧,冷位约束固定点应力惯性矩断面系数安全系数3.6.3 焊接与热处理电弧焊电熔焊气熔焊电阻焊气焊等离子焊电渣焊焊条焊丝平焊角焊间断焊汉语词Spring hangerConstant hangerRolling hangerSnubberCantilever supportTriangular supportLegn-type supportL-type supportPole type supportSupport on wallSleeperSpecial supportExtrusionAlignmentSpanMomentBending momentTorqueLoadReactionDisplacementAngular rotationCold springRestraintFix point; Anchor pointStressMoment of inertiaSection modulesSafety factorArc weldingElectric fusion weldingFusion gas weldingElectric resistance weldingGas welding; flame weldingPlasma weldingElectroslag weldingWelding electrode(rod)Welding wireFlat weldingFillet weldingIntermittent welding英语词EFWFGWERW英语缩写点焊对焊搭焊现场焊工厂(车间)焊接坡口无损检验肉眼检验,外观检验超声波控伤磁粉探伤荧光渗透试验水压试验气压试验退火回火正火淬火调质高频淬火渗氮渗碳3.6.4 隔热及涂漆玻璃棉岩棉泡沫玻璃硅酸钙硅酸铝纤维珍珠岩泡沫混凝土蛭石矿渣棉硅藻土石棉板石棉布聚氨酯泡沫聚苯乙烯玻璃布沥青油毡镀锌铁丝镀锌铁丝网管壳毡(被)汉语词Spot weldingButt weldingLap weldingField weldShop weldGrooveNon-Destruction testingVisual testingUltrasonic testMagnetic particle testFluorescent penetrate inspectionHydraulic testingPneumatic testingAnnealingTemperingNormalizingQuenchingQuenching and temperingInduction hardeningNitrogen case-hardeningCarbonizationGlass woolRock woolFoam glass; Cellular glassCalcium silicateAluminosilicace fiberPerliteFoamed concrete; Cellular concreteVermiculiteMineral woolKieselguhr; DiatomiteAsbestos boardAsbestos clothPolyurethaneCellular polystyreneGlass(fiber)clothAsphaltAsphalt feltGalvanized wireGalvanized wire meshShellBlanket英语词F.W英语缩写镀锌铁皮铝板隔热,隔离,绝缘保温保冷人身保护隔音吸声导热系数支承环分贝涂漆底漆面漆防锈漆醇酸瓷漆酚醛漆沥青漆聚氨酯漆有机硅漆环氧树脂漆过氯乙烯漆无机富锌漆3.6.5 紧固件螺栓六角头螺栓方头螺栓双头螺栓环头螺栓沉头螺栓地脚螺栓松紧节,花兰螺栓U型螺栓T型螺栓自攻螺钉膨胀螺栓六角螺母方螺母蝶形螺母锁紧螺母垫圈方垫圈斜垫圈汉语词Galvanized(sheet)ironAluminum sheetInsulationHot instructionCold instructionPersonal protectionSound insulationSound-absorbingThermal conductivity factorSupport ringDecibelPaintingPrimary coat; Bottom coatFinishing coatAntirust paintAlkyd enamelPhenolic paintBituminous paintPolyurethane paintOrganic silicon paintEpoxy resin paintEthylene perchloride paintInorganic zinc-rich paintBoltHexagonal head boltSquare head boltStud boltEye boltCountersunk(head)screwAnchor bolt; Foundation boltTurnbuckleU-boltT-boltSelf tapping screwExpansion boltHexagonal nutSquare washerWing nutLock nutWasherSquare WasherSlant Washer英语词INS英语缩写弹簧垫圈开口销定位销铆钉右螺纹管螺纹锥管螺纹直管螺纹美国标准直管螺纹管子内螺纹梯形螺纹公制螺纹粗牙螺纹通长螺纹,全螺纹粗制的精制的3.7 相关词语基础设计详细设计规划布置阶段初步阶段分析设计阶段成品设计阶段先期确认图纸资料最终确认图纸资料数据表设计文件设计注释设计规定设计规定汇总表详细设计版用户变更通知命名表,管道表规划研究版设计布置图概略版设备布置图投标版设备布置图合同版设备布置图送审版设备布置图成品版设备布置图施工版设备布置图工作程序界区条件标准汉语词Spring washerCotter pinDowel pinRivetRight hand threadPipe threadTaper pipe threadStraight pipe threadAmerican standard taper pipe threadInternal pipe threadTrapezoid threadMetric threadCoarse threadFull threadCoarseFinished; FineBasic designDetail designPlanning stagePreliminary stageAnalytical Engineering phaseProduction design phaseAdvanced certified finalCertified finalData sheetDesign documentDesign noteDesign specificationDesign specification summary sheetDetail design issueClient change noticeNomenclaturePlanning plot planConceptual plot planProposal plot planAward plot planApproval plot planProduction plot planConstruction plot planWorking procedureBattery limit conditionStandard英语词NPTIPTACFCFSPECDSSSDDICCNSTD;STAND英语缩写参考,基准开工会议项目审核会厂商协调会项目进展情况报告顾客承包安装建设试车说明待定版次修改,修订审核提纲审定校核制图部门部,科,室专业图号项目项目号工厂,装置买方(供货)卖方(供货)制造厂(供货)由仪表(专业负责) 铭牌询价净正吸入压头静电接池分散控制系统附件合同号外汇备忘录公章索赔交货付款摄氏汉语词ReferenceKick-off meetingProject review meetingVender co-ordinative meetingProject status reportClient; CustomerContractorErectionConstructionCommissioningDescriptionHoldIssueRevision; ModifyCheck listApprovedCheckedByDepartmentDivisionDisciplineDrawing numberProjectJob No.PlantBy buyerBy sellerBy venderBy instrumentName plateInquireNet positive suction headStatic groundingDistributed Control SystemsAttachmentContract numberForeign exchangeMemorandumOfficial sealClaim indemnityCash on deliveryCentigrade英语词K.O,MVCMPSRREVAPVDCHKDBYDWG. No.Job. No.B.BB.SB.VB.INSTDCSCont No.C.O.DC英语缩写华氏国际单位制美国材料试验协会阀门及配件制造工业标准化协会(美) 全国消防协会(美)石油管线协会(美)美国国家标准协会(美)美国机械工程师学会国际标准化组织国际电工技术委员会美国石油学会美国自来水厂协会美国仪表学会全国电气制造商协会(美) 日本工业标准加拿大标准协会英国标准德国工业标准FahrenheitSystem InternationalAmerican Society for Testing and MaterialsManufacturer s′Standardization Society of ValvAnd Fittings Industry National Fire Protection AssociationAssociation of Oil Pipe LinesAmerican National Standard InstituteAmerican Society of Mechanical Engineers InternationalOrganization for Standardization International Electrotechnical CommissionAmerican Petroleum InstituteAmerican Water Works AssociationInstrument Society of AmericanNational Electrical Manufactures Association Japanese Industrial StandardCanadian Standard AssociationBritish StandardDeutsche Industrie NormFSIASTMMSSNFPAAOPLANSIASMEISOIECAPIAWW AISANEMAJISCASBSDIN4 按英文字母排列英语词英语缩写汉语词3-Way ball valve3-Way ball valve3-Way valve4-Way ball valve45°LateralAAbove groundAbsolute elevationAbsorberAcrylonitrile-butadiene-styrene rubber Advanced certified finalAgitatorAir coolerAlignmentAlkyd enamelAlligatorAlloy steelAlloy steel pipeAluminosilicace fiberAluminum AGABSACF三通球阀三通旋塞阀三通阀四通旋塞阀45°三通地上绝对标高吸收塔丙烯睛·丁二烯:苯乙烯橡胶先期确认图纸资料搅拌器空冷器对中心，找正醇酸瓷漆颚式破碎机合金钢合金钢管硅酸铝纤维铝Aluminum magnesium Aluminum sheetAmerican National Standard Institute American Petroleum InstituteAmerican Society for Testing and Materials American Society of Mechanical Engijeers American standard taper pipe thread American Water Works Association Analytical Engineering phaseAnalyzerAnchorAnchor boitAnch pointAngle steelAngle valveAngular rotationAnnealingAntirust paintApproval plot planApprovedArc weldingAsbestAsbestos boardAsbestos clothAsphaltAsphalt feltAssociation of Oil Pipe Lines AtmosphereAtomizerAttachmentAttachment equipmentAustenitic stainless steelAustenitic stainless steel pipeAward plot planAxial flow pumpBBag-Shape pipeBall type expansion jointBall valveBase plateBasic designBattery limit ANSIAPIASTMASMENPTAWW AAPVDAOPLATMB.L铝镁合金铝板美国国家标准协会（美）美国石油学会美国材料试验协会美国机械工程师学会美国标准直管螺纹美国自来水厂协会分析设计阶段分析室固定架地脚螺栓固定点角钢角阀(角式截止阀)角位移退火防锈漆送审版设备布置图审定电弧焊石棉石棉板石棉布沥青油毡石油管线协会(美)大气,大气压粉碎机,磨碎机附件附属设备,附件奥氏体不锈钢奥氏体不锈钢管合同版设备布置图轴流泵袋形管球型补偿器球阀底板基础设计装置边界Battery limit condition Battery roomBeamBell and spigot joint BelledBellow expansion joint Bellow swaled valve Belt filterBendBending moment Bituminous paintBlankBlanketBlindBlindBlind flangeBlock valveBlow down valve BlowerBoilerBoltBolt circleBolt cold diameter Bolt cold tightening Bolt hot tightening BossBottomBottom coat Bottom of base plate Bottom of pipeBox type filer press Branch connection BrassBreakerBreather valve Bridge crane British Standard Bucket elevator BuildingButt weldedButt welded joint Butt welding Butterfly valve L.BL.BB.CBOTBBPBOPBSBWBW界区条件电池室梁承插连接,套筒连接承插的波纹膨胀节波纹管密封阀带式过滤机弯管弯矩沥青漆盲板,管道盲板毡(被)盲板,管道盲板法兰盖法兰盖切断阀排污阀鼓风机锅炉螺栓螺栓圆直径螺栓圆直径螺栓冷紧螺栓热紧支管台(凹台)底面,底下底漆底板底面管底厢式压滤机支管连接黄铜破碎机呼吸阀板式起重机英国标准斗式提升机建筑物对焊的对焊连接对焊蝶阀Butyl rubberByBy buyerBy instrumentBy sellerBy venderBy-pass valveCCable tray(channel)Calcium silicateCanadian Standard Association Canned pumpCantilever supportCapCar seal closeCar seal openCarbon fiberCarbon pipeCarbon steel CarbonizationCase(shell)Cash on deliveryCasingCast ironCast iron pipeCast steelCaving holeCellular concreteCellular glassCellular polystyreneCenter lineCenter to CenterCenter to EndCenter fo FaceCentigradeCentrifugal compressor Centrifugal filter Centrifugal pump Centrifugal separator CentrifugerCeramic PIBIBYB.BB.INSTB.SB.VCASCC.S.CC.S.OCARC.SC.O.DC.IC.HC-CC-EC-FC丁基橡胶制图买方(供货)由仪表(专业负责)卖方(供货)制造厂(供货)旁路阀电缆槽(架)硅酸钙加拿大标准协会屏蔽泵悬臂架管帽关闭后加铅封(封关)开启后加铅封(封开)碳纤维碳钢管碳钢渗碳外壳交货付款外壳铸铁铸铁管铸钢开孔泡沫混凝土泡沫玻璃泡沫聚苯烯中心线中心至中心中心至端面中心至面摄氏离心压缩机离心过滤机离心泵离心分离机离心机陶瓷。
管材、管件、阀门、接头、管道特件、紧固件、密封等中英文对照
管材、管件、阀门、接头、管道特件、紧固件、密封等中英⽂对照管材、管件、阀门、接头、管道特件、紧固件、垫⽚、密封、⼯程材料等中英⽂对照化⼯管道设计技术英语词汇(1－2－3)1管道组成件Pipingcomponent1.1管⼦Pipe管⼦(按照配管标准规格制造的)pipe管⼦(不按配管标准规格制造的其他⽤管)tube钢管steelpipe铸铁管castironpipe衬⾥管linedpipe复合管cladpipe碳钢管carbonsteelpipe合⾦钢管alloysteelpipe不锈钢stainlesssteelpipe奥⽒体不锈钢管austeniticstainlesssteelpipe铁合⾦钢管ferriticalloysteelpipe轧制钢管wrought-steelpipe锻铁管wrought-ironpipe⽆缝钢管seamless(SMLS)steelpipe焊接钢管weldedsteelpipe电阻焊钢管electric-resistanceweldedsteelpipe电熔（弧）焊钢板卷管electric-fusion(arc)-weldedsteel-platepipe螺旋焊接钢管spiralweldedsteelpipe镀锌钢管galvanizedsteelpipe热轧⽆缝钢管hot-rollingseamlesspipe冷拔⽆缝钢管cold-drawingseamlesspipe⽔煤⽓钢管water-gassteelpipe塑料管plasticpipe玻璃管glasstube橡胶管rubbertube直管runpipe;straightpipe1.2管件Fitting弯头elbow异径弯头reducingelbow带⽀座弯头baseelbowk半径弯头longradiuselbow短半径弯头shortradiuselbow长半径180°弯头longradiusreturn短半径180°弯头shortradiusreturn带侧向⼝的弯头（右向或左向）sideoutletelbow(righthandorlefthand)双⽀管弯头（形）doublebranchelbow三通tee异径三通reducingtee等径三通straighttee带侧向⼝的三通（右向或左向）sideoutlettee(righthandor1efthand)异径三通（分⽀⼝为异径）reducingtee(reducingonoutlet)异径三通（⼀个直通⼝为异径）reducingtee(reducingononerun)带⽀座三通basetee异径三通（⼀个直通⼝及分⽀⼝为异径）reducingtee(reducingononerunandoutlet)异径三通（两个直通⼝为异径，双头式）reducingtee(reducingonbothruns,bullhead)45°斜三通45°lateral45°斜三通（⽀管为异径）45°lateral(reducingonbran ch)45°斜三通(⼀个直通⼝为异径)45°lateral(reducingononerun)45°斜三通(⼀个直通⼝及⽀管为异径)45°lateral(reducingononerunandbranch)Y型三通（俗称裤衩）true“Y”四通cross等径四通straightcross异径四通reducingcross异径四通（⼀个分⽀⼝为异径）reducingcross(reducingononeoutlet)异径四通（⼀个直通⼝及分⽀⼝为异径）reducingcross(reducingononerunandoutlet)异径四通（两个分⽀⼝为异径）reducingcross(reducingonbothoutlet)异径四通（⼀个直通⼝及两个分⽀⼝为异径）reducingcross(reducingononerunandbothoutlet) 异径管reducer 同⼼异径管concentricreducer偏⼼异径管eccentricreducer锻制异径管reducingswage螺纹⽀管台threadolet焊接⽀管台weldolet承插⽀管台sockolet弯头⽀管台elbolet斜接⽀管台latrolet镶⼊式⽀管嘴sweepolet短管⽀管台nipolet⽀管台，插⼊式⽀管台boss管接头coupling,fullcoupling半管接头halfcoupling异径管接头reducingcoupling活接头union内外螺纹缩接（俗称补芯）bushing管帽cap(C)堵头plug短节nipple异径短节reducingnipple;swagenipple1.3弯管Bend预制弯管fabricatedpipebend跨越弯管（^形）cross-overbend偏置弯管（~形）offsetbend90°弯管quarterbend环形弯管cirelebend单侧偏置90°弯管（?形）singleoffsetquarterbend S形弯管“S”bend单侧偏置U形膨胀弯管（|?形）singleoffset“U”bend U形弯管“U”bend双偏置U膨胀弯管doubleoffsetexpansion“U”bend斜接弯管mitrebend三节斜接弯管3-piecemitrebend折皱弯管corrugatedbend圆度roundness1.4法兰Flange(FLG）整体管法兰integralpipeflange钢管法兰steelpipeflange螺纹法兰threadedflange滑套法兰（包括平焊法兰）slip-onflange(SO);slip-onweldingflange 承插焊法兰socketweldingflange 松套法兰lapjointflange(LJF)对焊法兰weldingneckflange(WNF)法兰盖blindflange,blind孔板法兰orificeflange异径法兰reducingflange盘座式法兰??padtypeflange松套带颈法兰loosehubbedflange焊接板式法兰??weldingplateflange对焊环weldingneckcollar（与stubend相似）平焊环welding-oncollar突缘短节stubend,lap翻边端lappedpipeend松套板式法兰looseplateflange压⼒级pressurerating,pressureratingclass压⼒—温度等级pressure-temperaturerating法兰密封⾯，法兰⾯flangefacing突⾯raisedface(RF)凸⾯maleface(MF)凹⾯femaleface(FMF)榫⾯tongueface槽⾯grooveface环连接⾯ringjointface全平⾯；满平⾯flatface;fullface(FF)光滑突⾯smoothraisedface(SRF)法兰⾯加⼯facingfinish粗糙度roughness光滑的smooth齿形serrated均⽅根rootmeansquare(RMS)算术平均粗糙⾼度arithmeticalaverageroughnessheight(AARH)配对法兰companion-flange螺栓圆boltcircle(B.C.)1.5垫⽚Gasket(GSKT)垫⽚的型式typeofgasket平垫⽚flatgasket环形平垫⽚flatringgasket平⾦属垫⽚flatmetalgasket夹棉织物的橡胶elastomerwithcottonfabricinsertion夹⽯棉织物的橡胶elastomerwithasbestosfabricinsertion夹⽯棉织物及⾦属丝加强的橡胶elastomerwithasbestosfabricinsertionandwithwirereinforcement⽆⽯墨压缩⽩⽯棉垫⽚nongraphitedcompressedwhiteasbestosgasket天然⽩橡胶垫⽚naturalwhiterubbergasket压缩⽯棉垫⽚compressedasbestosclassgasket浸聚四氟⼄烯的⽯棉垫⽚PTFEimpregnatedasbestosgasket夹⽯棉的缠绕⾦属垫⽚spiral-woundmetalgasketwithasbestosfiller内环innerring外环，外定位环outerring波纹⾦属垫⽚corrugatedmetalgasket波纹⾦属包嵌⽯棉垫⽚corrugatedmetalgasketwithasbestosinserted双夹套波纹⾦属包⽯棉垫⽚corrugatedmetaldoublejacketedasbestosfilledgasket 双夹套垫⽚doublejacketedgasket ⾦属包⽯棉平垫⽚flatmetaljacketedasbestosfilledgasket整体⾦属齿形垫⽚solidmetalserratedgasket槽形⾦属垫⽚groovedmetalgasket环形连接⾦属垫⽚ringjointmetalgasket⼋⾓环形垫⽚octagonalringgasket椭圆环形垫⽚ovalringgasket透镜式垫⽚lensgasket⾮⾦属垫⽚non-metallicgasket1.6阀门Valve1.6.1阀门结构、零件阀轭yoke外螺纹阀杆及阀轭outsidescrewandyoke(OS&Y)阀杆stem内螺纹insidescrew(IS)阀轭套yokesleeve阀杆环stemring阀座valveseat(bodyseat)阀座环、密封圈seatring整体（阀）座integralseat堆焊（阀）座depositedseat阀芯（包括密封圈、杆等内件）trim阀盘disc阀盘密封圈discseat阀体body阀盖bonnet阀盖衬套bonnetbush螺纹阀帽screwcap螺纹阀盖screwbonnet螺栓连接的阀盖boltedbonnet(BB)活接阀盖（帽）unionbonnet(cap)螺栓连接的阀帽boltedcap(BC)焊接阀盖weldedbonnet(WB)本体阀杆密封bodystemseal⽯棉安全密封asbestosemenenseal倒密封backseal压⼒密封的阀盖pressure-tightbonnet 动⼒操纵器poweredoperator 电动操纵器electricmotoroperator⽓动操纵器pneumaticoperator液压操纵器hydraulicoperator快速操纵器quick-actingoperator滑动阀杆slidingstem正齿轮传动spurgearoperated伞齿轮传动bevelgearoperated扳⼿操作wrenchoperated链轮chainwheel⼿轮handwheel⼿柄handlever(handle)⽓缸（或液压缸）操纵的cylinderoperated链条操纵的chainoperated等径孔道fullbore;fullport异径孔道reducingbore,reducedport,venturiport 短型shortpattern 紧凑型（⼩型）compacttype笼式环lanternring压盖gland阀杆填料stempacking阀盖垫⽚bonnetgasket升杆式（明杆）risingstem(RS)⾮升杆式（暗杆）non-risingstem(NRS)指⽰器/限位器indicator/stopper注油器greaseinjector可更换的阀座环renewableseatring1.6.2常⽤阀(1）闸阀gatevalve平⾏双闸板doublediscparallelseat开⼝楔形闸板splitwedge挠性整体楔形闸扳flexiblesolidwedge整体楔形闸板solidwedge塞型闸阀pluggatevalve直通型闸阀throughconduitgatevalve(2)截⽌阀globevalve球⼼型阀盘globetypedisc塞型阀盘plugtypedisc可转动的阀盘swiveldisc(3)节流闪阀throttlevalve针阀needlevalve(4)⾓阀anglevalve(5)Y型阀（Y型阀体截⽌阀）Y-valve(Y-bodyglobevalve)(6)球阀ballvalve三通球阀3-wayballvalve装有底轴的trunnionmounted耐⽕型firesafetype浮动球型floatingballtype防脱出阀杆blowoutproofstem(7)蝶阀butterflyvalve对夹式（薄⽚型）wafertype凸⽿式lugtype偏⼼阀板蝶阀offsetdiscburerflyvalve;eccentricbutterflyvalve 斜阀盘蝶阀canteddiscbutterflyvalve 连杆式蝶阀linkbutterflyvalve8)柱塞阀pistontypevalve(9)旋塞阀plugvalve三通旋塞阀three-wayplugvalve四通旋塞阀four-wayplugvalve旋塞cock衬套旋塞sleevecock(10)隔膜阀diaphragmvalve橡胶衬⾥隔膜阀rubberlineddiaphragmvalve直通式隔膜阀straightwaydiaphragmvalve堰式隔膜阀weirdiaphragmvalve(11)夹紧式胶管阀pinchvalve（⽤于泥浆、粉尘等）(12)⽌回阀checkvalve升降式⽌回阀liftcheckvalve旋启式⽌回阀swingcheckvalve,flapcheckvalve落球式⽌回阀ballcheckvalve弹簧球式⽌回阀springballcheckvalve双板对夹式⽌回阀dualplatewafertypecheckvalve ⽆撞击声⽌回阀non-slamcheekvalve 底阀footvalve切断式⽌回阀stopcheckvalve;non-returnvalve活塞式⽌回阀pistoncheckvalve斜翻盘⽌回阀tiltingdisccheckvalve蝶式⽌回阀butterflycheckvalve1.6.3其它⽤途的阀安全泄⽓阀safetyvalve(SV)安全泄液阀reliefvalve(RV)安全泄压阀safetyreliefvalve杠杆重锤式leverandweighttype引导阀操纵的安全泄⽓阀pilotoperatedsafetyvalve复式安全泄⽓阀twintypesafetyvalve罐底排污阀flush-bottomtankvalve电磁阀solenoidvalve,solenoidoperatedvalve电动阀electricallyoperatedvalve,electric-motoroperatedvalve⽓动阀pneumaticoperatedvalve低温⽤阀cryogenicservicevalve蒸汽疏⽔阀steamtrap机械式疏⽔阎mechanicaltrap浮桶式疏⽔阀openbuckettrap,opentopbuckettrap浮球式疏⽔阀floattrap倒吊桶式疏⽔阀invertedbuckettrap⾃由浮球式疏⽔阀loosefloattrap恒温式疏⽔阀thermostatictrap⾦属膨胀式蒸汽疏⽔阀metalexpansionsteamtrap液体膨胀式蒸汽疏⽔阀liquidexpansionsteamtrap双⾦属膨胀式蒸汽疏⽔阀bimetallicexpansionsteamtrap压⼒平衡式恒温疏⽔阀balancedpressurethermostatictrap热动⼒式疏⽔阀thermodynamictrap脉冲式蒸汽疏⽔阀impulsesteamtrap放⽓阀（⾃动放⽓阀）airventvalve(automaticairventvalve)（疏⽔阀⽤）平板式滑动闸阀slabtypeslidinggatevalve盖阀flatvalve换向阀divertingvalve,reversingvalve热膨胀阀thermoexpansionvalve⾃动关闭阀self-closinggatevalve⾃动排液阀self-drainingvalve管道盲板阀line-blindvalve挤压阀squeezevalve（⽤于泥浆及粉尘等）呼吸阀breathervalve风门、挡板damper减压阀pressurereducingvalve,reducingvalve控制阀controlvalve膜式控制阀diaphragmoperatedcontrolvalve执⾏机构actuator背压调节阀backpressureregulatingvalve差压调节阀differentialpressureregulatingvalve 压⼒⽐例调节阀pressureratioregulatingvalve 1.6.4未指明结构（或阀型）的阀切断阀blockvalve;shut-offvalve;stopvalve调节阀regulatingvalve快开阀quickopeningvalve快闭阀quickclosingvalve隔断阀isolatingvalve三通阀threewayvalve夹套阔jacketedvalve⾮旋转式阀non-rotaryvalve排污阀blowdownvalve集液排放阀dripvalve排液阀drainvalve放空阀ventvalve卸载阀unloadingvalve排出阀dischargevalve吸⼊阀suctionvalve多通路阀multiportvalve取样阀samplingvalve⼿动阀hand-operatedvalve;manuallyoperatedvalve 锻造阀forgedvalve 铸造阀castvalve（⽔）龙头bibb;bib;faucet抽出液阀（⼩阀）bleedvalve旁路阀by-passvalve软管阀hosevalve混合阀mixingvalve破真空阀vacuumbreaker冲洗阀flushvalve第⼀道阀；根部阀primaryvalve根部阀rootvalve总管阀headervalve事故切断阀emergencyvalve1.7管道特殊件PipingSpecialty1.7.1管道特殊件（组件）粗滤器strainer过滤器filter临时粗滤器（锥型）temporarystrainer(conetype)y型粗滤器y-typestrainerT型粗滤器T-typestrainer永久过滤器permanentfilter丝⽹粗滤器gauzestrainer洗眼器及淋浴器eyewasherandshower视镜sightglass阻⽕器flamearrester喷嘴；喷头spraynozzle取样冷却器samplecooler消声器silencer膨胀节expansionjoint波纹膨胀节bellowexpansionjoint单波singlebellow双波doublebellow多波multiplebellow压⼒平衡式膨胀节pressurebalancedexpansion带铰链膨胀节hingedexpansionjoint轴向位移型膨胀节axialmovementtypeexpansionjoint⾃均衡膨胀节（外加强环）self-equalizingexpansionjoint 带接杆膨胀节tiedexpansionjoint 万向型膨胀节universaltypeexpansionjoint球形补偿器balltypeexpansionjoint填函式补偿器sliptype(packedtype)expansionjoint单向滑动填料函补偿器singleactionpackedslipjoint1.7.2管道特殊元件PipingSpecialElement软管接头hoseconnection(HC)快速接头quickcoupling⾦属软管metalhose橡胶管rubberhose挠性管flexibletube鞍形补强板reinforcingsaddles补强板reinforcementpad特殊法兰specialflange漏⽃funnel排液环dripring排液漏⽃drainfunnel插板blank垫环spacer8字盲板spectacleblind;figure8blind 限流孔板restrictionorifice爆破⽚rupturedisk法兰盖贴⾯protectivedisc费托⽴克接头victauliccoupling1.8端部连接EndConnection法兰端flangedend坡⼝端beveledend(BE)对焊端buttweldedend平端plainend(PE)承插焊端socketweldingend螺纹端threadedend(TE)承⼝bellend焊接端weldingend法兰连接（接头）flangedjoint对焊连接（接头）buttweldedjoint螺纹连接，管螺纹连接threadedjoint,pipethreadedjoint 锥管螺纹密封焊连接seal-weldedtaperpipethreadedjoint 承插焊连接（接头）socketweldedjoint承插连接（接头）bellandspigotjoint环垫接头ringjoint(RJ)万向接头universaljoint软钎焊连接（接头）solderedjoint搭接接头，松套连接lappedjoint外侧厚度切斜⾓bevelforoutsidethickncss内侧厚度切斜⾓bevelforinsidethickness内外侧厚度切斜⾓bevelforcombinedthickness法兰式的flanged(FLGD)对焊的buttwelded(BW)螺纹的threaded(THD)承插焊的socketwelded(SW)⼩端为平的smallendplain(SEP)⼤端为平的largeendplain(LEP)两端平bothendsplain(BEP)⼩端带螺纹smallendthread(SET)⼤端带螺纹largeendthread(LET)两端带螺纹bothendthread(BET)⼀端带螺纹oneendthread(OET)⽀管连接branchconnection焊接⽀管branchpipeweldeddirectlytotherunpipe 2管道⽤紧固件及螺纹2.1紧固件螺栓bolt六⾓头螺栓hexagonalheadbolt⽅头螺栓squareheadbolt螺柱，双头螺栓studbolt环头螺检eyebolt沉头螺栓countersunk(head)screw地脚螺栓anchorbolt;foundationbolt 松紧螺旋扣（花篮螺丝）turnbuckle U形螺栓U-boltT形螺栓T-bolt圆头螺钉roundheadbolt机螺栓，机螺钉maehinebolt顶开螺栓，顶起螺栓Jackscrew⾃攻螺钉selftappingscrew膨胀螺栓expansionbolt粗制的coarse精制的finished,fine螺母nut六⾓螺母hexagonalnut⽅螺母squarenut蝶形螺母wingnut扁螺母flatnut锁紧螺母locknut垫圈washer平垫圈plainwasher球⾯垫圈sphericalwasher弹簧垫圈springwasher⽅垫圈squarewasher斜垫圈slantwasher销轴pinnedshan销pin开⼝销cotterpin定位销dowelpin带孔销pinwithhole圆锥销taperpin铆钉rivet键key2.2??螺纹左螺纹lefthandthread右螺纹righthandthread管螺纹pipethread锥管螺纹taperpipethread直管螺纹straightpipethread 梯形螺纹trapezoidthread 螺距pitchofthread。
常用管道、阀门、材料中英文名称对照
常用管道、阀门、材料中英文名称对照目录1 管道组成件Piping component (1)1.1 管子Pipe (1)1.2 管件Fitting (2)1.3 弯管Bend (3)1.4 法兰Flange (FLG） (4)1.5 垫片Gasket (GSKT) (5)1.6 阀门Valve (6)1.7 管道特殊件Piping Specialty (10)1.8 端部连接End Connection (12)1 管道组成件Piping component1.1 管子Pipe管子(按照配管标准规格制造的) pipe管子(不按配管标准规格制造的其他用管) tube钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carbon steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管austenitic stainless steel pipe 铁合金钢管ferritic alloy steel pipe轧制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resistance welded steel pipe电熔（弧）焊钢板卷管electric-fusion (arc)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe镀锌钢管galvanized steel pipe热轧无缝钢管hot-rolling seamless pipe冷拔无缝钢管cold-drawing seamless pipe水煤气钢管water-gas steel pipe塑料管plastic pipe玻璃管glass tube橡胶管rubber tube直管run pipe; straight pipe1.2 管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbowk半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand)异径三通（分支口为异径）reducing tee (reducing on outlet) 异径三通（一个直通口为异径）reducing tee (reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee (reducing on one run and outlet) 异径三通（两个直通口为异径，双头式）reducing tee (reducing on both runs, bull head) 45°斜三通45° lateral45°斜三通（支管为异径）45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run) 45°斜三通(一个直通口及支管为异径) 45° lateral (reducing on one run and branch)Y型三通（俗称裤衩）true “Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross (reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross (reducing on one run and outlet) 异径四通（两个分支口为异径）reducing cross (reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross (reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss管接头coupling, full coupling半管接头half coupling异径管接头reducing coupling活接头union内外螺纹缩接（俗称补芯）bushing管帽cap (C)堵头plug短节nipple异径短节reducing nipple; swage nipple1.3 弯管Bend预制弯管fabricated pipe bend跨越弯管（^ 形）cross-over bend偏置弯管（~ 形）offset bend90°弯管quarter bend环形弯管cirele bend单侧偏置90°弯管（? 形）single offset quarter bendS形弯管“S” bend单侧偏置U形膨胀弯管（| ?形）single offset “U” bend U形弯管“U” bend双偏置U膨胀弯管double offset expansion “U” bend 斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness1.4 法兰Flange (FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange (SO); slip-on welding flange 承插焊法兰socket welding flange松套法兰lap joint flange (LJF)对焊法兰welding neckflange (WNF)法兰盖blind flange, blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar （与stub end相似）平焊环welding-on collar突缘短节stub end, lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating, pressure rating class压力—温度等级pressure-temperature rating法兰密封面，法兰面flange facing突面raised face (RF)凸面male face (MF)凹面female face (FMF)榫面tongue face槽面groove face环连接面ring joint face全平面；满平面flat face; full face (FF)光滑突面smooth raised face (SRF)法兰面加工facing finish粗糙度roughness光滑的smooth齿形serrated均方根root mean square (RMS)算术平均粗糙高度arithmetical average roughness height (AARH)配对法兰companion-flange螺栓圆bolt circle (B.C.)1.5 垫片Gasket (GSKT)垫片的型式type of gasket平垫片flat gasket环形平垫片flat ring gasket平金属垫片flat metal gasket夹棉织物的橡胶elastomer with cotton fabric insertion夹石棉织物的橡胶elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶elastomer with asbestos fabric insertion and with wire reinforcement无石墨压缩白石棉垫片non graphited compressed white asbestos gasket天然白橡胶垫片natural white rubber gasket压缩石棉垫片compressed asbestos class gasket浸聚四氟乙烯的石棉垫片PTFE impregnated asbestos gasket 夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler内环inner ring外环，外定位环outer ring波纹金属垫片corrugated metal gasket波纹金属包嵌石棉垫片corrugated metal gasket with asbestos inserted双夹套波纹金属包石棉垫片corrugated metal double jacketed asbestos filled gasket 双夹套垫片double jacketed gasket 金属包石棉平垫片flat metal jacketed asbestos filled gasket整体金属齿形垫片solid metal serrated gasket槽形金属垫片grooved metal gasket环形连接金属垫片ring joint metal gasket八角环形垫片octagonal ring gasket椭圆环形垫片oval ring gasket透镜式垫片lens gasket非金属垫片non-metallic gasket1.6 阀门Valve1.6.1 阀门结构、零件阀轭yoke外螺纹阀杆及阀轭outside screw and yoke (OS & Y) 阀杆stem 内螺纹inside screw (IS)阀轭套yoke sleeve阀杆环stem ring阀座valve seat (body seat)阀座环、密封圈seat ring整体（阀）座integral seat堆焊（阀）座deposited seat阀芯（包括密封圈、杆等内件）trim阀盘disc阀盘密封圈disc seat阀体body阀盖bonnet阀盖衬套bonnet bush螺纹阀帽screw cap螺纹阀盖screw bonnet螺栓连接的阀盖bolted bonnet (BB)活接阀盖（帽）union bonnet (cap)螺栓连接的阀帽bolted cap (BC)焊接阀盖welded bonnet (WB)本体阀杆密封body stem seal石棉安全密封asbestos emenen seal倒密封back seal压力密封的阀盖pressure-tight bonnet动力操纵器powered operator电动操纵器electric motor operator气动操纵器pneumatic operator液压操纵器hydraulic operator快速操纵器quick-acting operator滑动阀杆sliding stem正齿轮传动spur gear operated伞齿轮传动bevel gear operated扳手操作wrench operated链轮chain wheel手轮hand wheel手柄hand lever (handle)气缸（或液压缸）操纵的cylinder operated链条操纵的chain operated等径孔道full bore; full port异径孔道reducing bore, reduced port,venturi port 短型short pattern紧凑型（小型）compact type笼式环lantern ring压盖gland阀杆填料stem packing阀盖垫片bonnet gasket升杆式（明杆）rising stem (RS)非升杆式（暗杆）non-rising stem (NRS)指示器/限位器indicator/stopper注油器grease injector可更换的阀座环renewable seat ring1.6.2 常用阀(1）闸阀gate valve平行双闸板double disc parallel seat开口楔形闸板split wedge挠性整体楔形闸扳flexible solid wedge整体楔形闸板solid wedge塞型闸阀plug gate valve直通型闸阀through conduit gate valve(2) 截止阀globe valve球心型阀盘globe type disc塞型阀盘plug type disc可转动的阀盘swivel disc(3) 节流闪阀throttle valve针阀needle valve(4) 角阀angle valve(5) Y型阀（Y 型阀体截止阀）Y-valve (Y-body globe valve)(6) 球阀ball valve三通球阀3-way ball valve装有底轴的trunnion mounted耐火型fire safe type浮动球型floating ball type防脱出阀杆blowout proof stem(7) 蝶阀butterfly valve对夹式（薄片型）wafer type凸耳式lug type偏心阀板蝶阀offset disc burerfly valve; eccentric butterfly valve 斜阀盘蝶阀canted disc butterfly valve连杆式蝶阀link butterfly valve8) 柱塞阀piston type valve(9) 旋塞阀plug valve三通旋塞阀three-way plug valve四通旋塞阀four-way plug valve旋塞cock衬套旋塞sleeve cock(10) 隔膜阀diaphragm valve橡胶衬里隔膜阀rubber lined diaphragm valve直通式隔膜阀straight way diaphragm valve堰式隔膜阀weir diaphragm valve(11) 夹紧式胶管阀pinch valve（用于泥浆、粉尘等）(12) 止回阀check valve升降式止回阀lift check valve旋启式止回阀swing check valve, flap check valve 落球式止回阀ball check valve弹簧球式止回阀spring ball check valve双板对夹式止回阀dual plate wafer type check valve 无撞击声止回阀non-slam cheek valve底阀foot valve切断式止回阀stop check valve; non-return valve活塞式止回阀piston check valve斜翻盘止回阀tilting disc check valve蝶式止回阀butterfly check valve1.6.3 其它用途的阀安全泄气阀safety valve (SV)安全泄液阀relief valve (RV)安全泄压阀safety relief valve杠杆重锤式lever and weight type引导阀操纵的安全泄气阀pilot operated safety valve 复式安全泄气阀twin type safety valve罐底排污阀flush-bottom tank valve电磁阀solenoid valve, solenoid operated valve电动阀electrically operated valve, electric-motor operated valve气动阀pneumatic operated valve低温用阀cryogenic service valve蒸汽疏水阀steam trap机械式疏水阎mechanical trap浮桶式疏水阀open bucket trap, open top bucket trap浮球式疏水阀float trap倒吊桶式疏水阀inverted bucket trap自由浮球式疏水阀loose float trap恒温式疏水阀thermostatic trap金属膨胀式蒸汽疏水阀metal expansion steam trap液体膨胀式蒸汽疏水阀liquid expansion steam trap双金属膨胀式蒸汽疏水阀bimetallic expansion steam trap压力平衡式恒温疏水阀balanced pressure thermostatic trap热动力式疏水阀thermodynamic trap脉冲式蒸汽疏水阀impulse steam trap放气阀（自动放气阀）air vent valve (automatic air vent valve) （疏水阀用）平板式滑动闸阀slab type sliding gate valve 盖阀flat valve换向阀diverting valve, reversing valve热膨胀阀thermo expansion valve自动关闭阀self-closing gate valve自动排液阀self-draining valve管道盲板阀line-blind valve挤压阀squeeze valve（用于泥浆及粉尘等）呼吸阀breather valve风门、挡板damper减压阀pressure reducing valve, reducing valve控制阀control valve膜式控制阀diaphragm operated control valve执行机构actuator背压调节阀back pressure regulating valve差压调节阀differential pressure regulating valve压力比例调节阀pressure ratio regulating valve1.6.4 未指明结构（或阀型）的阀切断阀block valve; shut-off valve; stop valve调节阀regulating valve快开阀quick opening valve快闭阀quick closing valve隔断阀isolating valve三通阀three way valve夹套阔jacketed valve非旋转式阀non-rotary valve排污阀blowdown valve集液排放阀drip valve排液阀drain valve放空阀vent valve卸载阀unloading valve排出阀discharge valve吸入阀suction valve多通路阀multiport valve取样阀sampling valve手动阀hand-operated valve; manually operated valve 锻造阀forged valve铸造阀cast valve（水）龙头bibb; bib; faucet抽出液阀（小阀）bleed valve旁路阀by-pass valve软管阀hose valve混合阀mixing valve破真空阀vacuum breaker冲洗阀flush valve第一道阀；根部阀primary valve根部阀root valve总管阀header valve事故切断阀emergency valve1.7 管道特殊件Piping Specialty1.7.1 管道特殊件（组件）粗滤器strainer过滤器filter临时粗滤器（锥型）temporary strainer (cone type)y 型粗滤器y-type strainerT型粗滤器T-type strainer永久过滤器permanent filter丝网粗滤器gauze strainer洗眼器及淋浴器eye washer and shower视镜sight glass阻火器flame arrester喷嘴；喷头spray nozzle取样冷却器sample cooler消声器silencer膨胀节expansion joint波纹膨胀节bellow expansion joint单波single bellow双波double bellow多波multiple bellow压力平衡式膨胀节pressure balanced expansion带铰链膨胀节hinged expansion joint轴向位移型膨胀节axial movement type expansion joint自均衡膨胀节（外加强环）self-equalizing expansion joint 带接杆膨胀节tied expansion joint万向型膨胀节universal type expansion joint球形补偿器ball type expansion joint填函式补偿器slip type (packed type) expansion joint单向滑动填料函补偿器single actionpacked slip joint1.7.2 管道特殊元件Piping Special Element软管接头hose connection (HC)快速接头quick coupling金属软管metal hose橡胶管rubber hose挠性管flexible tube鞍形补强板reinforcing saddles补强板reinforcement pad特殊法兰special flange漏斗funnel排液环drip ring排液漏斗drain funnel插板blank垫环spacer8字盲板spectacle blind; figure 8 blind限流孔板restriction orifice爆破片rupture disk法兰盖贴面protective disc费托立克接头victaulic coupling1.8 端部连接End Connection法兰端flanged end坡口端beveled end (BE)对焊端butt welded end平端plain end (PE)承插焊端socket welding end螺纹端threaded end (TE)承口bell end焊接端welding end法兰连接（接头）flanged joint对焊连接（接头）butt welded joint螺纹连接，管螺纹连接threaded joint, pipe threaded joint 锥管螺纹密封焊连接seal-welded taper pipe threaded joint 承插焊连接（接头）socket welded joint承插连接（接头）bell and spigot joint环垫接头ring joint (RJ)万向接头universal joint软钎焊连接（接头）soldered joint搭接接头，松套连接lapped joint外侧厚度切斜角bevel for outside thickncss内侧厚度切斜角bevel for inside thickness内外侧厚度切斜角bevel for combined thickness法兰式的flanged (FLGD)对焊的butt welded (BW)螺纹的threaded (THD)承插焊的socket welded (SW)小端为平的small end plain (SEP)大端为平的large end plain (LEP)两端平both ends plain (BEP)小端带螺纹small end thread (SET)大端带螺纹large end thread (LET)两端带螺纹both end thread (BET)一端带螺纹one end thread (OET)支管连接branch connection焊接支管branch pipe welded directly to the run pipe37。
阀门专业术语中英文对照
角阀
angle back—pressure valve
背压角阀
angle globe valve
折角球形阀
angle stop valve
弯形止阀,折角止阀
angle water valve
折角水阀
annular ring valve
环形阀;环状阀
anti-g valve
【航空】防超重活门，抗重力阀
BL法兰盖
BC。SWING螺栓阀盖旋启式
BB.OS&Y螺栓阀盖外螺纹及轭式
BC.LIFT螺栓阀盖升降式
Dual—plate双蝶板
FB.L.OP.全通径手工操作
FB.GEAR OP。全通径齿轮操作
FF全平面
FL法兰
F锻件
GV镀锌
HF硬质合金堆焊
LJ活套法兰
L翻边短节短规格
LL翻边短节长规格
MFR'S.ST’d制造商标准
STL—-—Stellited硬质合金（钴－铬－钨合金)
BB—--Bolted Bonnet螺栓连接的阀盖
FLG---Flange法兰
NPT-——National Pipe Taper Thread 60°锥管螺纹
SWD—--Solid Wedge Disc楔形单闸板
BC—-—Bolted Cap螺栓连接的阀帽
"ENP—-—Electroless Nickel Plating镍磷硼合金镀层
NBR-—-Nitrile—butadiene Ruber丁腈橡胶
Sch.No。—-—Schedule Number管表号
Bana-N丁钠橡胶
FE——-Flanged End法兰连接端
阀门英文缩写词
阀门英文缩写词Hand-operated valves 手动阀Hard Seal Butterfly Valves 金属密封碟阀High Temperature Pressure Power Station Gate Valves 高温高压电站闸阀High Temperature Pressure Power Station Globe Valves 高温高压电站截止阀Hydraulic relay valves 液压继动阀Lift Check Valves 升降式止回阀Lift Check Valves 升降式止回阀Limit valves 限位阀Lining Ball Valves 衬里球阀Lining Butterfly Valves 衬里碟阀Lining Check Valves 衬里止回阀Lining Cock 衬里二通Lining Globe Valves 衬里截止阀Lining T-Cock Valves 衬里三通旋塞阀Liquid Indicator 液位计LPG Pipe Fitting 液化气管件Magnetic Co-operate Globe Valves磁耦合截止阀Magnetism Forle Pumps 磁力泵Manual Oil Pumps Valves 手摇油泵（阀）Meter Needle Type Globe Valves 仪表针形截止阀Oblique Stop Valves 直流式截止阀Parallel Slide Valves 浆液阀Pintle valve 针形阀Piping Centrifugal Pumps 管道离心泵Plunger valves 柱塞阀Pressure valve 压力（増压）阀Piping Pumps 管道泵Piping Safety Valves 管道安全阀Plunger Globe Valves 柱塞截止阀Quick Draining Valves 快速排污阀Restrictor Valves 过流阀（或节流阀）Safety Valves 安全阀Screw Pumps 螺杆泵Scum Gate Valves 排渣闸阀Solenoid valves 电磁阀Single Disc Flat Gate Valves 单闸板平板闸阀Single Opening Exhaust Valves 单口排气球Slurry Pumps 泥浆泵Stop Valves 截止阀Strainer 过滤器Submerged Motor Pumps 潜水电泵（排污泵）Swing Check Valves 旋启式止回阀Swing Check Valves 旋启式止回阀Air valves 空气阀门Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves 门角式截止阀Ash valves 排灰阀Aspirating valves 吸（抽）气阀Auxiliary valves 辅助（副）阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料（放空，排污）阀Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀Buttwelding valves 对焊连接阀Clamp valves 对夹式阀门Cock 二通Combination valves 组合阀CQ Thread Ball Valves CQ螺纹球阀Culvert valves 地下管道阀Deceleration valves 减速阀Diaphragm Valves 隔膜阀Decompression valves 泄压阀Double Disc Flat Gate Valves 双闸板平板闸阀Double Disk Parallel Gate Valves明杆平行式双闸板闸板Double Opening Exhaust Valves 双口排气球Drainage valves 排水阀Electric Actuated Stop Valves 电动截止阀Electric Actuated Wedge Gate Valves电动楔式闸阀Electric Double Disk Parallel Gate Valves电动平行式双闸板闸板Emergeny Cut-off Valves 紧急切断阀Exhaust valves 排气阀Free Float Type Steam Trap 浮球式疏水阀Flange Ball Valves 法兰球阀Flange Gate Valves 法兰闸阀Flange Globe Valves 法兰截止阀Gauge Valves 仪表阀Tank Lorry Ball Valves 槽车球阀T-Cock 三通Thin Gate Valves 薄型闸阀Throttle Valves 节流阀Tiny Drag Slow Shut Check Valves 微阻缓闭止回阀Triple （tee）valves 三通阀Two-way valves 二通阀Under Water Pumps 液下泵Vacuum Pumps 水力喷射器（真空泵）Vertical Lift Check Valves 立式止回阀Wafer Check Valves 对夹式止回阀Wafer plate valves 对夹蝶板阀Wafer Type Butterfly Valves with Rubber Itning对夹式衬胶蝶阀Waste Valves 排污箱（阀）Water Seal Gate Valves 水封闸阀Wedge Gate Valves 楔式闸阀Y Type and Cylinder Filters Y型筒型过滤器阀门零部件英汉术语对照Axis Guide 轴套Ball 球、球芯Ball seat 密封圈Blowdown Sealing Face 启、阀件密封面Body 阀体Bonnet 阀盖Disc 阀瓣Mut 螺母Screw 螺栓Sealing 密封件Spring 弹簧Stem 阀杆Stem Mut 阀杆螺母Stem seal 填料Wedge Disc 闸板阀门规范技术英语术语对照Applicable medium 适用介质Applicable temperature 适用温度Butt Clamp 对夹Chemical analysis 化学成份Connecting format 连接形式Double disc 双闸板Flexible disc 弹性闸板Flange 法兰Hoop 卡箍Inside thread 内螺纹Jacket 夹套Mains 电源Material chemical analysis and mechanical capacity材料化学成份和机械性能materials 材料Materials for main parts 主要零件材料Mechanical capacity 机械性能Max. Discharging Capacity 最大排水量Max. Operating Temperature 最高工作温度Max. Allowable Temperature 最高允许温度Max. Allowable Pressure 最高允许压力Model 型号Name of parts 零件名称nitrogen （N）氮Nominal bore 公称通径Nominal Pressure 公称压力Nozzle 排气口Outside thread 外螺纹Oxidant 氧化性介质Parallel 平行Piping 管路Piston 活塞Reductant 还原性介质Rising stem 明杆Seal 阀座，密封面Seat testing pressure 压力气密封试验压力Socket 卡套Specifications 性能规范Single disc 单闸板Solid 刚性Strengh testing pressure 强度试验压力Steam ，condensate 蒸汽，凝结水Stroke 冲程，行程Water，oil，steam 水，温度，气Wedge 楔式Welding 焊接阀门材质术语英汉对照Atbas metal 镍铬钢Buna-N rubber 丁晴橡胶Casting aluminium brass 铸铝黄铜Casting aluminium bronze 铸铝青铜Ceramic metal 陶瓷金属Chromel alloy 镍铬合金CHR rubber 氯晴橡胶Chrominm-molybdenum-vanadium steel 铬钼钒钢Chromium stainless steel 铬不锈钢Chromium-molybdenum steel 铬钼钢Corrugation pad 波形垫Cuprum alloy 铜合金Ductile Cast iron 球墨铸铁Expanded graphite 柔性石墨Fine Steel Casting iron 优质碳素钢Fluorous rubber 氟橡胶Gray Cast iron 灰铸铁Hayne's alloy 钴铬钨合金High tem perature steel 高温钢Monel 蒙乃尔合金Low temperature steel 低温钢Nylon 尼龙塑料Polytetrafluoroethylene（PTEF）聚四氟乙烯Polythene 聚乙烯Pure aluminium 纯铝Pure cupper 纯铜Rubber graphite board 橡胶石墨板Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力Service Fluid 工作介质阀门目录VALVES阀valves电磁阀solenoid valve球阀ball valve蝶阀butterfly valve截止阀globe valve控制阀controlvalve水阀waterworks valve换向阀Check Valve单向阀one-way valve电动阀electric valve疏水阀steam traps比例阀proportional valve隔膜阀diaphragm valve气阀gas valve膨胀阀expansion valve平衡阀balance valve溢流阀overflow valve调压阀regulating valve伺服阀servo valve节流阀throttle valve液压阀hydraulic valve防火阀firesafe valve三通阀 3 way valve气动调节阀pneumatic adjusting valve 压力调节阀pressure regulating valve 温控阀temperature control valve蝶阀butterfly valve波纹管bellow pipe。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
管道阀门材料的英文代码
缩写符号 中文 英文
B(in.or") 英寸 Inch
BB 螺栓连接的阀盖 Bolted Bonnet
BC 螺栓阀帽 Bolted Cap
BE 坡口端 Bevelled End
BW 对焊 Butt Weld
CA 腐蚀裕度 Corroison Allowance
CAF 压缩石棉纤维 Compressed Asbestos Fiber
CALC 计算 Calculate
CS 碳钢 Carbon Steel
CST 铸钢 Cast Steel
DWG 图 Drawing
EC 外涂 Exteral Coating
EFW 电熔焊 Electric fusion Weld
ERW 电阻焊 Elecric resistance Weld
FF 平面 Flat Face(Full Face)
FLG 法兰 Flange
FtoF 面至面 Face to Face
GALV 镀锌的 Galvanized
HEX.NUT 六角形螺母 Hexagonal Nut
HF 钨铬钴（硬质）合金表面 Hardened Facing(API ST'D 600Tadle3Trim No.5)
ID 内径 Inside Diameter
LB 磅 Pound
LIFT 升降式 Lift Type
LJ 翻边短管 Lap Joint
M&F 凹面和凸面 Male & Female
MAX 最大 Maximum
MIN 最小 Minimum
NB 无阀帽 Non-Bonnet
No. 序号 Number
NPS 管道公称直径 Nominal Pipe Size
NPI 美国标准锥管螺纹 American National Standard TaperPipe Thread
OD 外径 Outside Diameter
OS&Y 外螺纹阀轭 Outside Screw and Yoke Type
P&ID 工艺仪表流程图 Piping&Instrument Drawing
PE 平端 Plain End
PTFE 聚四氟乙烯 Polyterafluoroethylene
PVC 聚氯乙烯 Poly Vinyl Chloride
R 半径 Radius
RF 突面 Raised Face
RJ 环槽面 Ring Joint
S.BOLT 双头螺栓 Stud bolt
SCH 管表号 Schedule
SCRD 螺纹的 Screwed
SH
硬表面层
Surface Hardened Steel(API ST'D600Table3Trim
No.8or8A)
SMLS 无缝钢管 Seamless Steel
SO 平焊 Slip On
SS 不锈钢 Stainless Steel
ST'D 标准 Standard
SW 承插焊 Socket Weld
SWING 旋启式 Swing Type
T&G
榫面和槽面 Tongue＆Groove
TE 螺纹端 Threaded End
THD 螺纹的 Threaded
UFD 公用工程流程图 Utility Flow Drawing
WELD 焊接 Weld
WN 焊颈（对焊） Weld Neck
BBP EL 底板底面标高
B.L. 界区线
BOP EL 管道底标高
CL EL 中心线标高
DIS 出口
DR 导淋
ECC 底平偏心异径管
EL 标高
F.P. 固定点
FTF 管件对管件
M.L. 接图线
MI/SF 金属软管
PF EL 平台标高
PN 装置北
POS EL 支撑点标高
SUC 入口
TOP ECC 顶平偏心异径管
VENT 放空
WP EL 工作点标高
阀门种类
VS 闸阀
VB 球阀
VC 止回阀
VD 截止阀
VF 蝶阀
VG 隔膜阀
VN 针形阀
VR 旋塞阀
端面型式
F 法兰
B 对焊端
S 承插焊
T 螺纹端
W 对夹式
压力等级
A 150Lb（2.0MPa）
B 300Lb（5.0MPa）
C 600Lb（11.0MPa）
D 800Lb
E 900Lb（15.0MPa）
F 1500Lb（26.0MPa）
G 2500Lb（42.0MPa）
K 1.0MPa
L 1.6MPa
M 2.5MPa
N 4.0MPa
P 6.3MPa
Q 10.0MPa
R 16.0MPa
T 25.0MPa
W 特殊压力级
阀体材质
A 铸铁
B 碳钢
C 低合金钢
D 合金钢
E 不锈钢
F 非金属
G 衬里及内防腐
H 有色金属
K 特殊材料
X
渡锌碳钢