Components of suction caisson capacity measured in axial pullout tests
海上风电基础结构研究现状及发展趋势
第２期黄维平，等：海上风电基础结构研究现状及发展趋势１３１ｌ海上风电基础结构研究１．１设计荷载研究作用在海上风电机组基础结构上的荷载包括风轮机运转荷载（见图１）和海洋环境荷载。
风轮机运转荷载是由风和风机叶片相互作用产生的，Ｒｕｎｅ等人心］采用气动弹性方法计算作用在叶片、风轮机及水面上结构的空气动力荷载，采用非线性弹簧和阻尼器模拟桩一土相互作用，研究了单桩结构在风浪作用下的动力耦合响应问题。
研究表明，基础结构的性质对海上风电机组结构系统的动力特性有较大的影响，因此，基础结构模型作为系统气动弹性模型的一部分是非常重要的。
它不仅影响基础结构的设计荷载，而且影响系统其它组成部分的设计荷载。
极端响应是海上风电机组基础结构设计的一个重要变量，它图１风轮机荷载示意Ｆｉｇ．１Ｌｏａｄｏｆ诵ｎｄｔｕｒｂｉｎｅ包括叶片的拍向弯矩和基础结构的倾覆力矩。
文献［３］采用现场测量数据对极端响应分布的统计不确定性进行了贝叶斯分析，结果表明，极端响应的概率分布符合韦伯分布。
海上风电机组基础结构与海洋平台的结构形式有较大区别，且水深较浅。
因此，波浪荷载的计算多采用非线性波模型。
Ｌｉａｎｇ等人［４］研究了非线性波与海上风电机组基础结构相互作用的数值模拟问题，提出了一个新的模拟非线性波与任意截面形状直立结构相互作用的数值方法。
该方法的主要优点是不需要特殊的算法来模拟破碎波。
Ｈｅｎｄｅｒｓｏｎ等人［５］采用线性和非线性波浪模型研究了波浪运动模型、波浪荷载模型和结构模型对确定海上风电机组基础结构流体动力荷载的影响。
研究表明，采用线性波模型计算海上风电机组基础结构流体动力荷载是不安全的，应该采用非线性波模型。
文献［６］的研究表明，结构的最大流体动力荷载出现在强非线性非破碎波条件下。
随着海上风电技术的不断进步，风机规格越来越大，水深越来越深，使得传统固定式基础结构的一阶固有频率降至０．２５～０．３５Ｈｚ之间。
而一些海浪谱，如瑞典Ｂｏｃｋｓｔｉｇｅｎ海上风电场测量的海浪谱，其第二个谱峰频率约为０．３Ｈｚ，可能引起共振。
船舶英语专业用语
主船体main hull 上层建筑superstructure上甲板/上层连续甲板upper deck 船底bottom舷侧broadside 艏艉fore and aft舱壁bulkhead 水密watertight艏部bow 艉部stern/quarter二层甲板second deck 平台甲板platform deck桅屋masthouse 罗经甲板compass deck驾驶甲板bridge deck 船长甲板master deck高级船员甲板office deck 艇甲板boat deck船员甲板crew deck 机舱engine room货舱cargo hold 货舱口cargo hatch压载舱ballast tank 深舱deep tank燃油舱fuel oil tank 滑油舱lubricating oil tank淡水舱fresh water tank 污油水舱slop tank隔离空舱/干隔舱caisson 球鼻艏标志bulbous bow mark/BB mark首侧推器标志bow thruster mark/BT mark 吃水标志draft mark甲板线deck line 干舷甲板freeboard deck载重线标志load line mark 热带淡水载重线tropical fresh water load line/TF夏季淡水载重线fresh water load line/F 热带载重线tropical load line/T夏季载重线summer load line/S 冬季载重线winter load line北大西洋冬季载重线winter North Atlantic load line/WNA国际船舶载重线证书international load line certificate吃水指示系统draft indicating system 船舶尺度ship dimension最大尺度/全部尺度/周界尺度overall dimension 最大长度/全长/总长length overall/LOA最大宽度/全宽extreme breadth 最大高度maximum height净空高度air draught 船型尺度/型尺度/主持度moulded dimension 垂线间长L/length between perpendiculars 型宽B/moulded breadth型深D/moulded depth 型吃水d/moulded draft登记尺度register dimension 登记长度register length登记宽度register breadth 登记深度register depth船舶主尺度比dimension ratio 船长型宽比L/B , length breadth ratio船长型深比L/D , length depth ratio 船长型吃水比L/d , length draft ratio型宽型吃水比B/d , breadth draft ratio 型深型吃水比D/d , depth draft ratio重量吨weight tonnage 排水量displacement满载排水量dead displacement 空船排水量light displacement装载排水量load displacement 总载重量deadweight/DW净载重量net deadweight/NDW 容积吨/登记吨capacity tonnage总吨位/总吨gross tonnage/GT 净吨位net tonnage/NT运河吨位canal tonnage/CT 抗沉性floatability全客船passenger vessel 客货船passenger-cargo vessel货客船cargo-passenger vessel 客滚船ro-ro passenger ship集装箱船container ship 箱格导轨系统cellguide system散装货船bulk carrier 散装货物bulk cargo舱口围板hatch coaming 横剖面cross-section边舱side tank 压载舱ballast tank矿砂船ore carrier 压载边舱side ballast tank内底板inner bottom plating 兼用船combination carrier矿砂/石油两用船，O/O船ore/oil carrier 矿砂/散货/石油三用船，OBO船ore/bulk/oil carrier 杂货船general cargo ship 滚装船roll on/roll off ship , Ro/Ro ship木材船timber carrier 冷藏船refrigerated ship多用途船multi-purpose ship 液货船liquid cargo ship易燃液体inflammable liquid 油船oil tanker污油水舱slop tank 液体化学品船liquid chemical tanker液化气船liquefied gas carrier 液化天然气船liquefied natural gas carrier/LNG carrier液化石油气船liquefied petroleum gas carrier/LPG carrier 乙烯运输船ethylene tanker工程船engineering ship 挖泥船dredger起重船floating crane 海洋调查船marine survey ship敷缆船cable ship 航标船navigation mark ship工作船working ship 拖船tug供应船supply boat 破冰船icebreaker海难救助船rescue ship 消防船fire boat科学考察船scientific research ship 船体结构ship construction钢板plate 型钢section steel扁钢flat bar 球扁钢bulb bar角钢angle bar , A/B 工字钢I-barT型钢T-bar 槽钢channel bar铸钢，铸件casting 锻钢，锻件forging焊接welding 周围焊around welding电弧焊/电焊electric arc welding 气焊gas welding焊缝weld 塞焊plug welding端接焊end welding 角接焊fillet welding对接焊butt welding 搭接焊lap welding坡口groove 覆板doubling plate铆接riveting 板材deals and battens骨架skeleton 总纵强度total longitudinal strength扭转强度torsional strength 横向强度transverse strength局部强度local strength 坐坞强度docking strength刚度rigidity 稳定性stability应力集中stress concentration 船台building berth横骨架式transverse framing system 横向构件transverse member舷顶列板sheer strake 舷侧板side plating舭列板bilge strake 船底板bottom plating中内龙骨center keelson 旁内龙骨side keelson梁肘板beam knee 平板龙骨(flat) plate keel甲板纵桁deck girder 肋骨frame强肋骨web frame 舷侧纵桁side girder肋板floor 横梁beam横舱壁板transverse bulkhead plating 舱容hold capacity外板shell plate 内底板inner bottom plating纵向构件longitudinal member 自重sole weight纵骨架式longitudinal framing system 船底纵骨bottom longitudinal中桁材center girder 旁桁材side girder舷顶列板sheer strake 舷侧纵骨 side longitudinal撑材strut 甲板纵骨deck longitudinal强横梁web beam 舱口围板hatch coaming纵舱壁longitudinal bulkhead 舭龙骨bilge keel二层甲板tween deck 内底边板margin plate实肋板/主肋板solid floor 内底纵骨inner bottom longitudinal加强筋stiffener 人孔manhole舱口端梁hatch end beam 支柱pillar船舱肋骨hold frame 甲板间肋骨tweendeck frame舷侧列板side strake 舭肘板/污水沟三角板bilge bracket舱口端横梁hatch end beam 防倾肘板tripping bracket舷墙板bulwark plating 舷强扶强材bulwark stiffener换新renew 基本结构图basic construction plan纵中剖面结构图central fore-and-aft plane construction plan 各层甲板图deck plan 内底结构图inner bottom construction plan 列板strake舭列板bilge strake 甲板边板deck stringer基线base line 横剖面图transverse cross-section plan中横剖面图midship transverse cross-section plan机舱处横剖面图engine-room transverse cross-section plan货舱口处横剖面图cargo hatch transverse cross-section plan舱壁图bulkhead plan 总布置图general arrangement plan船底结构bottom construction 下甲板横梁lower deck beam上甲板横梁upper deck beam 支柱肘板pillar bracket双层底结构double bottom construction 骨架framing首防撞舱壁fore collision bulkhead 尾尖舱舱壁afterpeak bulkhead肘板bracket 水密肋板watertight floor内底纵骨inner bottom longitudinal 实肋板solid floor组合肋板/框架肋板bracket floor 扶强材side girder船底横骨bottom frame 流水孔drain hole透气孔air hole 减轻孔lightening hole切口incision 内底横骨inner bottom frame横骨架式双层底结构transversely framed double bottom construction轻型肋板lightened floor 水密舱壁watertight bulkhead面板 face plate 折边flanging中桁材/中底桁center girder 中内底板center inner bottom plating箱形中桁材/箱形龙骨duct keel 管隧pipe tunnel水密纵桁watertight longitudinal girder 内底纵骨inner bottom longitudinal内底横骨inner bottom frame 船底中心线bottom center line旁桁材/旁底桁/旁龙骨side girder 人孔盖manhole cover污水沟bilge drainage/side bilge 污水井bilge well/bilge sump单层底结构single bottom construction 中内龙骨center keelson旁内龙骨side keelson 舷侧外板side plating甲板边板deck stringer 主肋骨main frame甲板间肋骨tweendeck frame 尖舱肋骨peak frame肋距frame space 中间肋骨intermediate frame普通肋骨ordinary frame 强肋骨web frame舷侧纵桁side stringer 舷侧纵骨side longitudinal舷边gunwale 舷边角钢gunwale angle bar止裂crack arrest 舷墙bulwark舷墙板bulwark plating 支撑肘板buttress bracket扶手armrest 栏杆hand rail舱口纵桁hatch side girder 甲板纵中线deck center line舱口端梁hatch end beam 强力甲板strength deck甲板间舱tweendeck space 遮蔽甲板shelter deck舱壁甲板bulkhead deck 干舷甲板freeboard deck量吨甲板tonnage deck 半梁half beam斜置加强筋tilt stowing stiffener 管型支柱tubular pillar水平加强筋horizontal stiffener 菱形面板diamond plate悬臂梁cantilever beam 梁拱camber舷弧线sheer curve 舷弧sheer首舷弧fore sheer 尾舷弧after sheer首尖舱fore peak tank 首尖舱舱壁fore peak tank bulkhead防撞舱壁collision bulkhead 尾尖舱舱壁after peak tank bulkhead 防火舱壁fireproof bulkhead 液体舱壁liquid bulkhead油密oiltight 制荡舱壁wash bulkhead平面舱壁plane bulkhead 舱壁板bulkhead plate舱壁扶强材bulkhead stiffener 水平桁horizontal girder对称槽形舱壁symmetrical corrugated bulkhead 三角形triangle矩形rectangle 梯形trapezoid弧形arc 双层底double bottom tank底边舱lower side tank 顶边舱top side tank底登lower stool 直立型首straight bow首柱stem/stem post 驳船barge前倾型首raked bow 飞剪型首clipper bow首楼甲板forecastle deck 破冰型首ice resistant bow兴波阻力wave making resistance 形状阻力form resistance铸钢首柱cast steel stem post 钢板首柱steel plate stem post锚链舱chain locker 升高肋板raised floor强胸横梁panting beam 外板shell plate开孔平台trepanned platform 椭圆形尾elliptical stern巡洋舰形尾cruiser stern 方型尾transom stern尾封板stern transom plate 船首结构bow construction强力构件strength member 剖面模数section modulus船尾结构stern construction 尾肋板transom floor尾柱底骨sole piece 推进器柱propeller post轴毂propeller boss 舵钮rudder gudgeon舵柱rudder post 斜横梁cant beam舵机舱平台steering gear room platform 尾升高肋板stern raised floor斜肋骨cant frame 舵杆管rudder case防火措施fire precaution 防火结构fire structure耐火材料refractory material 主竖区main vertical zone不燃材料non-combustible material 自燃autoignition易燃蒸气inflammable vapour 可燃材料combustible material等效材料equivalent material 防火分隔fire resisting divisionA级分隔/甲级分隔A class division 天花板ceiling衬板furring 轴隧shaft tunnel推进器轴propeller shaft 逃生孔escape trunk中机型船amidship-engined ship 尾机型船stern-engined ship单车船single-screw ship 顶板top plating木铺板batten ceiling 滑动式水密门slid watertight door拱形顶板arch top plating 平顶板flat top plating轴承基座stool supporting shaft bearing 管系piping格子板grating 舭龙骨/减摇龙骨bilge keel坞修dock repair 船底塞docking plug坞墩docking block 锰黄铜manganese brass不锈钢stainless steel 舭部外板bilge plate舷侧型线moulded line of side shell 船底型线moulded line of bottom shell 垫圈insertion ring 垫板pad隔离空舱caisson 双层舷侧double side shell双层壳double shell 中间舱center tank边舱side tank 甲板下纵桁deck lower girder业务衡准数criterion of service numeral 舱底水管系bilge system舱底水管路bilge pipe 吸口suction过滤器filtrator 舱底水总管bilge main line止回阀non-return valve 舱底泵bilge pump阀箱valve casing 泥箱mud box油水分离器oil-water separator 测量管/测深管sounding pipe旋塞faucet 螺纹盖thread cap防击板striking plate 压载管系ballast system压载水ballast water 压载管路ballast pipe调驳阀箱control valve easing 压载泵ballast pump截止阀stop valve 海底阀/通海阀sea suction valve舷侧排水阀overboard discharge valve 空气管air pipe花钢板diamond plate 自动关闭阀automatic closing valve通风管系ventilating system 自然通风natural ventilation烟斗式通风筒cowl-head ventilator 排风筒uptake ventilator蘑菇形通风筒mushroom ventilator 起重柱Samson post鹅颈式通风筒gooseneck ventilator 机械通风mechanical ventilator风机aerator 管路pipe conduit吸口空气滤器suction air filter 空气调节air conditioning system消防管系fire extinguishing system 固定式灭火系统fixed fire extinguishing system 水灭火系统water fire extinguishing system 气体灭火系统gas fire extinguishing system 泡沫灭火系统foam fire extinguishing system水雾灭火系统water fog fire extinguishing system自动喷水系统automatic sprinkling fire extinguishing system惰性气体保护系统inert gas system 日用水管系domestic water supply system日用淡水系统domestic fresh water system 日用热水系统domestic warm water system 饮用水系统potable water system 重力水柜gravity tank压力水柜pressure tank 循环泵circulating pump甲板排水管系 deck scupper system 甲板排水器deck scupper排水管scupper pipe 卫生排泄系统sanitary water system锚anchor 锚穴anchor recess锚链筒hawse pipe 制链器chain stopper锚机windlass 锚链管chain pipe锚链舱chain locker 锚链chain cable闸刀switch blade 制动销detent pin松紧螺丝扣turnbuckle 弃链器releasing gear横闩式弃链器dog type cable clench 螺旋弃链器screw type cable releaser手轮hand wheel 螺杆screw脱钩senhouse slip 末端链环end open link首锚bow anchor 尾锚stern anchor有杆锚/海军锚stocked anchor 锚铃环anchor ring锚干anchor shank 锚爪anchor fluke锚冠anchor crown 锚爪臂anchor arm锚尖anchor bill 锚爪掌anchor flukepalm锚杆销forelock pin 横杆folding stock无杆锚/山字锚stockless anchor 锚卸扣anchor shackle锚肩/助抓突角anchor shoulder 销轴pintle横销pin cotter 大抓力锚high holding power anchor普通链环common link 加大链环enlarged link末端链环end open link 散合式连接链环detachable link肯特卸扣Kenter link 转环swivel link电动锚机electric windlass 电动液压锚机hydraulic windlass电动机electromotor 减速器reducer传动齿轮drive gear 离合器clutch链轮chain wheel 刹车操纵杆brake control rod带缆卷筒rope drum 带式刹车brake绞盘capstan 锚机间windlass room锚链末端bitter end 舾装数/船具数N/equipment number备锚spare anchor 大抓力锚HHP超大抓力锚SHHP 挂锚hanging off an anchor。
六级常用英语词汇及翻译
aluminum paint 银粉漆
aluminum sheet 铝皮
ambient air temperature 环境气温
ambient temperature 环境温度
anchor block 地锚块
anchor bolt 地脚螺栓
anchor ground 锚地
in line with = as per = in the light of 按照
acetylene gas 乙炔
acid electrode 酸性焊条
acid proof cement 防酸水泥
additive 添加剂
adhere to 遵守（动词）
adherence to 遵守（名词）
center of gravity 重心
center punch 冲子
central control room (CCR) 中央控制室
central processing platform 中心处理平台
centrifugal pump 离心泵
centrifuger 离心机
ceramic fibres 防火陶棉
backing weld 打底焊道
backpressure regulator (self contained) 背压式调节阀（自力式）
backwash return pump 反冲洗回流泵
backwash surge tank 反冲洗罐
Ball hardness 布氏硬度
ball valve 球阀
blowhole; gas pore 气孔
blowout preventer stack 防喷器组
技术词汇(英语)
技术英语词汇AA-60 fire door A－60级防火门Abrasive (喷砂用的)磨料abrasive paper 砂纸AC generator 交流发电机AC motor 交流电动机Accelerated corrosion testing 加速腐蚀试验Acceptance criteria 合格准则access hole (for welding)= cope hole (焊接)工艺孔accommodation and power platform (APP) 生活动力平台according to = in accordance with = in line with = as per =in the light of 按照acetylene gas 乙炔acid electrode 酸性焊条acid proof cement 防酸水泥Additive 添加剂adhere to 遵守(动词)Adherence to 遵守(名词)adjacent columns 相邻立柱adverse combination of loads 荷载的不利组合adverse condition 不利条件aeronautical radio system 航空无线电系统AFC (approved for construction) 建造批准aforementioned 上述的aft winch 船艉绞车Agitator 搅拌器a-hundred-year return period 百年一遇air blower 鼓风机air compressor 空压机air driven pump 气动泵air hoister 气动绞车air manifold 气包air tight test 气密性试验aircraft obstruction beacon 航空障碍灯air-hose 风带alarm buzzer 报警蜂鸣器alarm horn 报警喇叭aliphatic polyurethane 脂肪族聚氨酯漆Allowable(working) stress 许用应力Aluminum alloy anode 铝合金阳极Aluminum ingot 铝锭Aluminum paint 银粉漆Aluminum sheet 铝皮ambient air temperature 环境气温ambient temperature 环境温度anchor block 地锚块anchor bolt 地脚螺栓anchor ground 锚地anchor pile 锚桩anchor profile 磨料喷入母材的深度anchor pattern 磨料喷后母材留下的小坑形状(圆形、角形等) anchor rack 锚架anchoring buoy 锚泊浮筒angle of incidence 入射角angle of reflection 折射角angle probe method 超声波斜射探伤angle steel 角钢angle valve 角阀anode core 阳极芯子anode end face geometry 阳极端面几何形状anode life 阳极寿命anode potential 阳极电位anode stand-off post 支架式阳极的立柱anodic resistance 阳极电阻anticorrosive paint 防锈漆anti-electrostatic floor 防静电地板antipollution measures 防污染措施API specified requirements API规定的要求apparent batter 视斜度applicable API specification API 适用规范approach-departure sector 直升飞机起落扇形区Appurtenance =attachment =accessory =auxiliary 附件arc air gouging 碳弧气刨arc cutting 电弧切割arc strike 弧击argon arc welding 氩弧焊argon arc welding machine 氩弧焊机articulated tower mooring system 铰接塔系泊系统artificial island 人工岛as per 按照as-built 完工as-built dossier 完工资料as-built drawing 完工图as-rolled 轧制状态Assemble 组装(动词)Assembly 组装(名词)Associated gas 伴生气at the option of A 按A的意愿atmospheric diving system= unpressurized diving system 常压潜水系统atmospheric vent 放空管attachments 附件auto fire alarm system 火灾自动报警系统automatic spraying system 自动喷淋系统B(to be ) buttered (焊接的)长肉back chipping 清根back gouging 反面气刨Backing weld 打底焊道backpressure regulator (self contained) 背压式调节阀(自力式)backwash return pump 反冲洗回流泵backwash surge tank 反冲洗罐backwash tank 反冲洗水罐Ball hardness 布氏硬度ball valve 球阀Bar (截面较小的)圆钢方钢六角钢等bar chart 统计用的柱状图barge bumper 靠船件barge strength and stability 驳船强度及稳性Barrel (管件的)加厚段base metal 母材、基本金属basic design 基本设计basic electrode= lime type covered electrode 碱性焊条battery room 蓄电池间beam depth 梁高beam path distance 超声波发射程距bearing strength of the ground 地基承载力bearing stress 支撑应力before welding is initiated 始焊前Bending moment 弯矩Bending stress 弯曲应力Bevel 坡口bevel angle 坡口面角度Beveling / chamfering 开坡口bid / tender for ... 投标bid drawing 招标图纸bilge alarm system 污水报警系统bilge/ fire pump 舱底污水－消防两用泵blast cleaning 喷砂除锈blind flange 盲法兰blind spectacle flange 快速盲法兰blow count 打桩的锤击数Blowdown vessel 排放罐blowhole; gas pore 气孔blowout preventer stack （BOP）防喷器组blowout preventer system(BOP system) 防喷器系统boat landing 登船平台bolt, nut and washer 螺栓、螺母及垫片bolted connection 螺栓连接Boom 吊机扒杆boom angle 吊臂倾斜角bore hole 镗孔boss with plug 带有丝堵的管座bottom echo 底面回声bottom sitting drilling platform 坐底式钻井船Boundary condition 边界条件Bow 船艏box beam 箱形梁box type joint 箱形节点Brace 拉筋bracelet anode 手镯式阳极branch member 支杆breathing apparatus , respirator 防毒面具Bridge 栈桥bridge (overhead) crane 天车吊Brittleness 脆性brush coating 用毛刷涂漆buckle fastener 绑带build-up girder 组合梁bulb angle 球扁钢bulk head 隔板，舱壁，刚性法兰(海管) buoyant turret mooring 浮筒转塔式系泊burn through 烧穿Burner 气焊工burr and flashing 飞边毛刺business and management 经营管理Butterfly valve 蝶阀butt-welded seam 对接焊缝Ccable hanger 电缆马脚cable layer 敷缆船cable rack /tray 电缆托架Caisson 沉箱caisson washing pump 洗舱泵caisson-type platform 沉箱式平台Can (管件的)段Cantilever beam 悬臂梁Cantilever jack-up rig 悬臂自升式钻井船Cantilever well module 悬臂式井口模块cap beam 帽梁capped steel 半镇静钢capsizing lever 倾覆力臂capsizing moment=overturn moment 倾覆力矩carbon arc air gouging 碳弧气刨carbon dioxide cylinder 二氧化碳气瓶carbon equivalent 碳当量carbon-dioxide(CO2) arc welding 二氧化碳气体保护电弧焊cargo master system 货油舱总监控系统cargo tank cleaning machine 洗舱机Carrier (搬运)小车carry out = perform = conduct= execute 进行、执行catenary anchor leg mooring (CALM) 悬链锚腿系泊cathodic protection 阴极保护cellar deck 底甲板cellar shutdown panel (CSDP) 井口系统关断盘cement grout 水泥浆cementing vessel 固井船center line 中心线center of buoyancy 浮心center of floatation 漂心center of gravity 重心center punch 冲子central control room (CCR) 中央控制室central processing platform 中心处理平台centrifugal pump 离心泵Centrifuger 离心机ceramic fibres 防火陶棉ceramic tiles 瓷砖certifying authority 第三方检验机构chain block 倒链、链滑车chair with arm-rests 带扶手的半软椅Chamfering 开坡口channel steel 槽钢charpy-V notch energy 夏比V形缺口韧性值charpy-V notch impact test 夏比V形缺口冲击试验chart datum 海图基准面check randomly 抽检check valve 止回阀checkered plate 花纹板chemical composition 化学成分chemical injection package 化学注入撬chemical injection system 化学药剂注入系统chemical seal 化学密封chipping hammer 敲渣锤Chisel 风铲Chord member 弦杆Christmas tree 采油树circumference 周长circumferential weld 环焊缝classification survey 入级检验clean water injection pump 清水注入泵clean water surge tank 清水缓冲罐Clearance 间隙Client 业主、顾客close drain tank 闭式排放罐closed / open circuit 闭/开路Closed drain pump 闭式排放泵closed drain tank 闭式排放罐clustered well heads 丛式井口CO2 cylinder unit CO2 气瓶组CO2 extinguisher CO2 灭火器coal tar epoxy paint 含焦油环氧涂料Coaming 档水扁钢Coating 涂装coating interval 涂漆间隔Coefficient 系数Cold formed pipe 冷卷管cold shut 冷隔cold work 冷加工、冷作collapse ring 加强环板Column 立柱combustible gas detector 可燃气体探测器Come-along 手搬葫芦commercial blast cleaning 普通级喷砂除锈commissioning 调试compile and maintain a document 编制和保存文件complete penetration groove weld 全熔透坡口焊Completion riser 完井立管complex joint 复杂节点Compliance with 符合(名词)comply with 符合(动词)composite rockwool ceiling 复合岩棉天花板composite rockwool panel 复合岩棉板concentric reducer 同心大小头Conceptual design 概念设计concrete platform 混凝土平台Condensate drum 冷凝液罐Condensing water 冷凝水Conductor 隔水套管conductor guide 套管导向Cone 大小口、锥体conform to = stick to = adhere to 符合、遵守Connection 节点、连接consumption rate 阳极消耗率Continuous beam 连续梁Continuous double fillet weld 双面连续贴角焊Continuous welding 连续焊Contract 合同Contraction stress 收缩应力Contractor 承包商control valve (accessories handwheel) 带手轮的控制阀control valve assembly 控制阀总成coordinates 坐标系coordination 协调cope hole (焊接)工艺孔corrective and preventive action 纠正和预防措施Correlation curve 相关曲线corrosion allowance 腐蚀余量corrosion coupon 腐蚀挂片corrosion protection 防腐Corrugated plate interceptor 斜板分离器Couplant UT用的耦合剂Coupling 连轴器、管箍Crack 裂纹crane barge, crane vessel 起重船crane support 吊机支撑Crater 焊口crawler crane 履带吊车Criteria (验收)标准cross angle 交叉角cross section 横截面crow bar 撬杠cruciform bollard 单十字带缆柱crude cooler 原油冷却器crude filter 原油过滤器crude heat exchanger 原油换热器crude loading /export pump 原油外输泵crude loading pump 原油装载泵crude oil drain tank 原油排放舱crude preheat exchanger 原油预热器crude suction strainer 原油吸入滤器crude transfer pump 原油输送泵cup support 垫墩curing time (油漆的)固化时间Current capacity (阳极的)电流容量Current density (阳极的)电流密度Current direction 海流方向curvature radius 曲率半径Customer (试比较purchaser 需方) 客户(签合同后,客户变需方)cut by torch 以火焰切割cut off 割除、割除物cutoff allowance 切割裕量Cutting plan 排板图Cutting sheet 单件图D( in ) duplicate 一式两份(to)drive piles 打桩DAC curves 距离-振幅曲线daily diesel filter 日用柴油滤器damage-prone connection 易破坏的节点Damper, dampener 减振器DC generator 直流发电机Decibel (dB) 分贝deck beam 甲板梁deck cover 甲板敷料deck crane 甲板吊车deck floor plate 甲板板deck water seal unit 甲板水封装置deep freeze compressor 深冷压缩机deepwater jacket 深水导管架defect /default /disconnection 缺陷Deflection 挠度dehydration degassing vessel 脱水除气器dehydration preheater 脱水预热器dehydrator feed pump 电脱水供给泵delivery of materials 材料交货Derrick barge 回转式起重船Desander 除砂罐design basis 设计基准design parameters 设计参数Detail 详图detail design 详细设计develop / establish a document 编制文件dew point 露点DFT(dry film thickness) 干膜厚度diagonal brace 斜拉筋dial gauge 百分表Diaphragm 隔板diaphragm valve 隔膜阀die stamp 钢印diesel daily tank 柴油日用罐diesel filter coalescer 柴油过滤净化装置diesel generator set 柴油发电机组diesel oil daily tank with heater 柴油日用罐(带加热器) diesel pump 柴油泵diesel storage tank 柴油储罐diesel storage tank with heater 柴油储罐(带加热器)diesel tank 柴油罐diesel transfer pump 柴油输送泵differential pressure control valve 差压控制阀Diffuser 布风器dihedral angle 二面角dimensional checks 尺寸检验direct / alternating current arc welding 直/交流电弧焊Direct current emergency supply 直流应急电源Disassembling 拆除Discontinuity 缺陷displacement oil tank 置换油罐distortion from welding 焊接变形Distress signals 遇险呼救信号Diver 潜水员diver support vessel 潜水作业船document approval and issue 文件的批准和下发Documentation 文件编制Dog 组装用的刀把Dolphin 系缆柱domestic sea water pump 生活海水泵double agent facility 双介质灭火装置double bed 双层床double bevel groove K 形坡口double bollard 双柱带缆柱double groove 双面坡口double probe method 双探头法Double V groove 双面V 形坡口(X 形坡口) doubler plate 垫板、包板down hill welding 下向焊drain pit 排放池draught gauge 吃水标尺drawing and specification 图纸及技术规格书drawing types 图纸种类Drilling module 钻井模块Drilling platform 钻井平台Drilling template 钻井基盘drillship ,drilling ship 浮式钻井船Driving voltage 驱动电压dry chemical extinguisher 干粉灭火器Dryer 烘箱dry-type tree 干式采油树during the course of fabrication 在制造过程中during the life of structures 结构寿命期间dye penetrant inspection8 着色检验dynamic-positioning rig 动力定位钻井船Dredger 挖泥船drift pin 心轴、销子drift test 管流试验、管线试通Drill 钻头图纸种类有：conceptual drawing 概念图纸basic drawing 基本设计图bid drawing 招标图纸design drawing 详细设计图fabrication drawing 加工设计图shop drawing 车间加工图as-built drawing 完工图Eearth lead 地线eccentric reducer 偏心大小头echo height 回波高度edge crimping (卷管的)压头edge preparation 坡口加工effective throat thickness 焊缝计算厚度elbow 弯头electric dehydrator 电脱水器electric desalter 电脱盐器electric drill 手电钻electric heater 电加热器electric submersible pump 电潜泵electrical connection 导电连接electric-hydraulic valve 电-液操作阀electrochemical property 电化学特性electrode 电焊条electrode covering 焊条药皮electrode holder 焊把、焊钳electrolyte 电解质electro-slag welding 电渣焊接elevation (EL) 标高、立面图elongation 延伸率emergency air compressor 应急空压机emergency ballast control system 应急压载控制系统emergency BOP recovery system 防喷器紧急回收系统emergency generator 应急发电机emergency light 应急照明灯emergency power station 应急电站emergency shutdown 紧急关断emergency shutdown system (ESD) 应急关断系统emergency switch board 应急开关柜emergency switch room 应急配电间emery cloth 金刚砂布emulsion transfer pump 乳化油输送泵engine room 动力舱、机舱engineering geotechnical vessel 工程地质船engineering vessel 工程船舶entire length 全长equal angle 等边角钢equation 公式equipment base 设备底座erection 安装ERW (electric resistance welding) 电阻焊escape route 逃生路线essential variable 焊接基本参数excess of weight 超重existing structure 已有结构explosion proof equipment 防爆设备exposure distance 防火距离extent of defect in % 缺陷百分率extent of inspection 检验范围extent of repair 返修率external surface of brace 拉筋的外表面extra margin of stress 应力裕量Ffabricated wide flange shape 焊接成的宽翼缘型钢fabrication aids 制造辅助物(如临时吊点) fabrication design 加工设计fabrication phase 制造阶段fabrication sequence 制造顺序fabrication yard 制造场地face bend test 表面弯曲试验facsimile transceiver 传真收发两用机fastener 紧固件fatigue damage 疲劳破坏field assembly 空间组对、现场组对field mating point 海上对接点(如导管架与组块对接点) field splice 现场拼接field weld 现场焊缝fifty year return period 五十年一遇file 锉刀filler metal 填充金属final fabrication tolerance 最终制造公差finish coat 面漆finished product 成品finite element analyses 有限元分析fire alarm siren 火灾警笛fire and gas detecting system 火灾－可燃气探测系统fire control panel 消防控制盘fire damper 防火风闸fire door closer, fire proof door 防火门fire extinguishing system 消防系统fire fighting water , fire water 消防水fire foam hydrant 消防泡沫栓fire hose station , hose box 消防箱fire monitor 消防炮fire panel 火灾－可燃气报警显示盘fire proof wall , fire wall 防火墙fire protected plastic tiles 防火塑料地板fire protection wall 防火墙fire station 消防软管箱fire water / foam monitor 消防炮(水或泡沫)fire water deluge system 大水量灭火系统fire water hose rock 消防水软管fire water hydrant 消防水栓fire water jockey pump 消防水增压泵fire water lift pump 消防水提升泵fire water pump 消防水泵fire-fighting vessel , fire boat 消防船fireman box 消防员箱first aid kit 急救箱first coat 底漆first stage hydro cyclone 一级水力旋流器first stage separator 一级分离器fitter 组装工fit-up 坡口组对fixed crude oil washing machine 固定式原油清洗机fixed drilling platform 固定式钻井平台fixed platform 固定式平台fixed tower SPM 塔系泊flame arrester 阻火器flame cutting 火焰切割flame cutting droplets and debris 火焰切割形成的熔滴和料头flame cutting machine 火焰切割机flame cutting torch 火焰割枪flammability limits 可燃度极限flange 翼缘、法兰flare assembly 火炬总成flare boom 火炬臂flare drum 闪蒸罐flare pilot gas 火炬引燃器flare scrubber 火炬分液器flare tower 火炬塔flat bar 扁钢flat plate anode 扁阳极flat welding 平焊flaw 裂纹flaw detectability 缺陷检测灵敏度flaw echo 缺陷回声flexible hose 柔性软管flexible riser 挠性立管floater controlled valve 浮球控制阀floating cargo hose 浮式输油软管floating loading hose 浮式装油软管floating oil production andstorage unit (FPSU) 浮式生产储油装置floating oil storage unit 浮式储油装置floating production platform 浮式生产平台floating production, storage and off-loading tanker 浮式生产储油外输轮floating state 飘浮状态flooding 注水floppy disk 软盘flow chart 流程图flow indicator (FI) 流量显示器flow quantity recorder (FQ) 累计流量计flow switch 流量开关flux 焊药flux cored arc welding (FCAW) 药芯焊flux-cored electrode 管状焊条flux-cored wire 药芯焊丝foam extinguishing system 固定式泡沫灭火系统foam monitor 泡沫炮foam station 泡沫站fog horn , fog signal 雾笛folding bed 折叠床folding chair 折叠椅foot print 被交位置foot valve 底阀forecastle 艏楼foreman 领班forged steel (FS) 锻钢fork lift 铲车、叉车forming 压制成型forming of plates into tubular 由板卷成管formula / equation of carbon equivalent 碳当量公式four way valve 四通阀fracture toughness 断裂韧性frame structure 梁格结构free water knockout vessel 游离水分离器fresh water pressure vessel 淡水压力罐fresh water pump 淡水泵fresh water tank with electric heater 淡水罐(带加热器) friction coefficient 摩擦系数fuel gas compressor package 燃气压缩机撬fuel gas heater 燃料气加热器fuel gas scrubber 燃气洗涤器fuel gas treatment package 燃料气处理撬fuel oil drain tank 燃料油排放罐fuel pump 燃油泵full coupling 全螺纹的接头full penetration weld 全熔透焊缝funnel-shaped guide 喇叭口状导向furnace 熔炉、加热炉fusible plug 易熔塞fusion /bond line 熔合线G(to be ) ground flush 磨平gantry crane 龙门吊gap gauge 间隙尺gas bottle 气瓶gas cutting 气割gas cutting machine with magnetic wheels 磁轮式气割机gas detector 可燃气体探测器gas export facility 天然气外输设施gas injection module 注气组块gas metal arc welding (GMAW) 熔化极气体保护焊gas processing plant 天然气处理厂gas shielded arc welding 气体保护电弧焊gas tungsten metal arc welding (GTAW) 钨极气体保护焊(含氩弧焊)gas turbine generator set 燃气轮发电机组gas turbine power generator 燃气轮机发电机gas welding 气焊gasket 垫圈gate valve 闸阀geophysical survey vessel 物探船girders and webs 水平桁材和垂直桁材girth weld 环缝global positioning system (GPS) 全球定位系统globe valve (normally closed) 截止阀(常闭) Glycerin 甘油Gouging 气刨graphite crucible 石墨坩埚grating 格栅gravity damper 重力风闸gravity platform 重力式平台gravity type foundation 重力式基础Grease 黄油, 润滑油Grind 打磨Grinder 砂轮机Grinding 打磨(名词)grinding machine 砂轮机grit 磨料grit blasting 喷丸除锈Groove 熔池groove angle 坡口角guard filter 保护滤器guide funnel 导向喇叭口guide structure 导向结构Gusset 节点板、筋板guyed tower platform 拉索塔平台Hhalf nipple 一端带螺纹的接头halogenated hydrocarbon local panel 卤化烃就地控制盘halogenated hydrocarbon cylinder 卤化烃瓶halogenated hydrocarbon fire extinguishing system 卤化烃灭火系统Hammer 锤子hand operated pump 手动泵hand winch 手动缆绳车Handrail 栏杆hard hat 安全帽Hardener 固化剂hauling to the front 牵引至码头前沿hazardous area 危险区heat affected zones (HAZ) 热影响区heat detector 热探测器heat exchanger 热交换器heat medium drain tank 热介质排放罐heat number 炉号heat traced pipeline 伴热管线heat treater 加热器处理器heat treatment 热处理Heater 加热器heater treater 热处理器heater treater feed pump 热处理器供液泵heating medium boiler package 热介质锅炉撬heating medium circulating package 热介质循环撬heating medium collection tank 热介质收集罐heating medium diesel daily tank 热介质柴油日用罐heating medium drain pump 热介质排放泵heating medium drain tank 热介质排放罐heating medium expansion vessel 热介质膨胀罐heating medium make-up pump 热介质再启动泵heating medium oil, thermal oil 传热介质油heating medium storage tank 热介质油储存罐heating, ventilation and air conditioning system (HAV) 采暖、通风、空调系统heave wall section 厚壁段heavy can 节点加厚段heavy duty coating 厚层防腐heavy plate 厚板heavy wall pipe 厚壁管helideck 直升机甲板helmet 安全帽、焊接面罩hex head bolt 六角头螺栓high / low pressure switch (PSHL) 高－低压开关high concentration gas alarm 高浓度可燃气报警high pressure condensate tank 高压凝析油罐high pressure flare 高压火炬high pressure separator (HP separator) 高压分离器high strength steel 高强度钢high-low 错皮histogram (统计用)直方图hold 待定hold point (检验的)停点holder 焊钳holiday detector 气孔探测仪horizontal distance 水平距离horizontal welding 横焊hose 软管hose assembly 软管总成hose connection 软管接头hose handling crane 软管起升吊机hose reel 软管轮hot dip galvanizing 热浸锌hot water pressure vessel with electric heater 热水压力罐(带加热器)hot work 明火作业H-shape H型钢human life and property 人民生命财产hydrant 消火栓hydraulic pile-driving hammer 液压打桩锤hydraulic press 液压机hydrostatic/ hydraulic test 水压试验hyperbaric diving system = pressurized diving system 高压潜水系统Iice-breaker 破冰船if (when) necessary 若有必要Ignitor 点火器immersion suit 防寒救生衣impact resistance 耐冲击性impressed-current protectionsystem 外加电流保护系统in accordance with 按照in any jacket plane 在任意导管架平面内in line with 按照in the light of 按照inclined stair 斜梯include but not limited to 包括但不限于included / groove angle 坡口角度inclusion 夹杂物incomplete fusion 未熔合incomplete penetration 未焊透inflatable liferaft 气胀式救生筏inlet gas generator package 惰性气体发生器撬inorganic Zinc primer 无机锌底漆in-process inspection 工序间的检验inside diameter (ID) 内径Inspection 检验inspection criteria 检验标准installation site 安装现场instrument air receiver 仪表空气接受器instrument capillary tube 仪表控制管线instrument master control room 仪表总控制室insulating flange 绝缘法兰Insulation 保温insulation (heat traced) 保温加伴热intact / damage stability 完整/破损稳性Interference (杆件之间的)相碰、打架intergranular corrosion 晶间腐蚀intermediate strength steel 中强度钢intermittent welding 断续焊internal and external beveling 内外坡口internal diameter 内径internal quality audits 内部质量审核internal stress 内应力interpass temperature 层间温度intersected pipe 被交管intersection line 相贯线invitation for bid = call for bid 招标JJack 千斤顶Jacket 导管架jacket cap 导管架帽jacket handling 导管架扶正jacket launching and upending 导管架下水及扶正jacket launching barge 导管架下水驳船jacket leg 导管架腿柱jacket leveling 导管架调平jacket lifted on and off the barge 吊上及吊下驳船的导管架jacket lifting eye 导管架吊耳jacket modification 导管架改造jacket panel 导管架片jacket panel assembly 导管架片组对jacket positioning 导管架定位jacket securing 导管架固定jacking state 升降状态jacking system 升降系统jack-up rig 自升式钻井船jockey pump 供消防水干管的补给水泵joint can 节点加厚段joint detail 节点详图J-tube J形管junction box (explosion proof) 接线箱(防爆型) Kkey plan 总图、索引图killed steel 镇静钢Kingpost 将军柱Llack of fusion 未融合lack of penetration 未焊透Ladder 直梯ladle analysis 熔炼分析lamellar tearing 层状撕裂Lap 焊缝盖面lap welding 搭接焊lateral load 侧向荷载launch / cargo barge 滑道式/装载式驳船launch way and rocker 滑道和摇臂launching and uprighting of a jacket 导管架的下水和直立launching truss 下水珩架lay barge 铺管船lead sections and subsequent add-ons of piles 首桩及后续桩段leak test 密封性试验(试漏)Leg 桩腿、导管leg of a fillet weld (角焊缝)焊角高度Level 水平仪level gauge (with drain) 液位计(带排放)life boat 救生艇life boat davit , davit 吊艇架life buoy 救生圈life jacket 救生衣life raft , life float 救生筏lift calculation 吊装计算lifting gear 吊艇机lifting load 起吊荷载lifting lug 吊点lifting padeye 吊点lifting up of panel structure 单片起吊light type combustible gas detector 轻质可燃气体探测器line pipe 管线管line throwing apparatus 抛绳装置liquid trap 液体捕集器living quarter 生活块LNG carrier, LNG tanker 液化天然气运输船loading arm 输油臂loading flexible hose 柔性装载软管loadout and seafastening 装船固定local deformation 局部变形local stress 局部应力longitudinal seam/weld 纵焊缝low explosion limit (LEL) 爆炸下限low heat input 低热量输入low hydrogen type electrode 低氢型焊条low pressure scrubber 低压气净化器low stress round nosed die stamp 低应力圆头钢印lower deck 下甲板lub oil drain tank 润滑油排放罐lub oil tank with heater 润滑油罐(带加热器) Lubricant oil transfer pump 润滑油传输泵Lug 吊耳Mmachinery deck 机械甲板machining 机加工macrosection 宏观断面magnetic particle and suspension 磁粉和悬剂magnetic particle technique (MT) 磁粉探伤main boiler 主锅炉main deck 主甲板main generator set 主发电机组main process line 主要工艺管线main switch room 主变电间main transformer room 主变压器室make-up drawing 造管图Manhole 人孔Manifold 管汇manned platform 驻人平台manual / hand welding 手工焊manufacturer's instruction 产品使用说明marine growth 海生物marine radio system 海事通讯系统marine transportation 海运Marking 做标记、划线marking and cutting 划线下料mat support jack-up rig 沉垫自升式钻井船Material 材质、材料material identification 材料标识material list 材料表material storage 材料储存material substitution 材料代用material take-off 材料估算单material traceability 材料跟踪maximum operating water depth 最大工作水深mean sea level (MSL) 平均海平面mechanical property 机械性能mechanical test 机械性能试验medium pressure separator (MP separator) 中压分离器member 杆件member drawing (杆件的)单件图member number 杆件号metacenter 稳心metal lash 钢板网mezzanine deck 夹层甲板、半甲板middle deck 中甲板mild steel 低碳钢mill 钢厂mill certificate 厂家的材质证书mill scale 钢材出厂时的表面氧化皮mill sheet 制造工艺规程表mineral slag 矿渣miscellaneous items 附件mismatch = high-low 错皮mobile drilling platform / rig 移动式钻井平台mobile radio system 移动式无线电系统model test 模型试验module 撬块、模块mold 模具mold lofting 放样moment 力矩moment of longitudinal inclination 纵倾力矩moment of transverse inclination 横倾力矩moment of inertia 惯性矩mooring bit 系缆柱mooring cable 系泊缆绳mooring dolphin 系缆柱mooring head 系泊头mooring template 系泊基盘mooring yoke 系泊刚臂motor operated valve 电动阀move to yard front 移至码头前沿mud mat 防沉板mudline 泥线multihead metering pump 多头计量泵multipass welding 多层焊multiple lift 多台吊车联合起吊multi-point mooring , spread mooring 多浮筒系泊系统multi-purpose epoxy 多用途环氧漆multi-supported beam 连续梁multi-well template system 多井基盘系统Nnavigation channel 导航灯navigational light 导航灯NC(numerical-control) cutting machine 数控切割机NDT 包括：near white metal 接近金属白色needle valve 针阀Nipple 对丝node can 节点段nominal diameter 公称直径non-combustible 不可燃物质non-conformance 不一致事项nondestructive examination(NDE) 无损检验nondestructive testing (NDT) 无损检验nonskid ceramic mosaic 防滑陶瓷马赛克normal practice 通常作法normalize 正火normally open / close valve 常开/常闭阀notch toughness 缺口韧性NRL (Naval Research Laboratory) drop weight test NRL 落锤试验nut 螺母penetrant technique (PT) 渗透检验radiographic technique (RT) 射线探伤magnetic particle technique (MT) 磁粉探伤ultrasonic technique (UT) 超声波探伤visual inspection 外观检验Oobsolete document 作废文件oceanographic research vessel 海洋调查船offshore drilling installation 海上钻井设施offshore drilling rig 海上钻井装置offshore hook-up 海上连接offshore installation 海上安装offshore installation site 海上安装现场offshore oil exploration 海洋石油勘探offshore platform 海洋平台offshore structure 海洋结构物oil boom, oil fence 围油栅oil concentration (污水)含油浓度oil depot 油库oil fence reel 围油栅卷筒oil moisture content 油雾含量oil pollution 石油污染oil recovery vessel 污油回收船oil spill 溢油oil storage barge 储油轮oil storage, loading andtransportation equipment 储油、装油与输油设备oil treatment facility 油处理设施oily water tank 含油污水仓oily water transfer pump 污油水传送泵one-line diagram 单线图onshore fabrication 陆上预制open drain pump 开式排放泵open drain tank 开式排放罐open drain tank with heater 开式排放罐(带加热器) open firing point 明火点operating condition 作业条件operating state 作业状态operation draft 作业吃水orifice plate 孔板流量计Original 原稿out of roundness 椭圆度outside diameter (OD) 外径Ovality 椭圆度over coating intervals 复涂间隔over head crane 天车吊Overboard 舷外Overhanging beam 悬臂梁overhead welding 仰脸焊Overlap 焊瘤Overlapping joint 搭接节点Owner 业主Oxyacetylene gas welding 氧－乙炔气焊oxyacetylene welding 氧乙炔焊oxygen cylinder 氧气瓶oxygen hose 氧气带Ppackaged air conditioner 空调机橇块Packer 封隔器Padeye 吊点paint brush 油刷子paint roller 油漆滚子Painter 油漆工panel assembling 平面组对，单片组对parasitic echo 干扰回声parent steel 母材past successful practice 以往成功的作法pedestal crane 基座式吊机pedestal crane 平台用吊机peening 捶击penetrant technique (PT) 渗透检验perimeter 周长periodical survey 定期检验permissible stress 许用应力perpendicularity of pipe end 管端垂直度personnel protection 人身保护phenolic paint 酚醛树脂涂料Philips driver 十字螺丝刀phthalic paint 苯二甲酸涂料pig launcher 清管器发射器pig receiver 清管接收器pile cap 桩帽pile driving records 打桩记录pile driving refusal 拒锤点pile extracting 拔桩pile foundation 桩基pile guide 桩导向pile penetration 桩的贯入度pile section / segment 桩段pile sleeve 桩套筒pile spacer 扶桩间隙块pile washing out 冲桩piling 打桩pilling barge 打桩船pilot house 驾驶室pinhole 针尖状气孔pipe diameter 管径pipe fitting 管件pipe rack 管子托架pipe shoe 管子支撑、管靴pipe wrench 管钳pipeline 管线、管道pipeline laying barge 铺管船piping and instrument diagram (P & ID) 管线仪表图plain end 无螺纹管端plan 平面图、布置图plasma arc cutting (PAC) 等离子弧切割plasma arc welding (PAW) 等离子弧焊接plate girder 板梁plate type heat exchanger 板式换热器platform 平台platform positioning on the site 导管架的现场定位platform-to-shore radio system 平台－海岸无线电系统pliers 钳子plug 丝堵plug valve 旋塞阀plummet 铅坠plus or minus 2 正负2。
船体常用英语
折边 flange 补板 collar plate 防倾肘板 tripping bracket 支柱 pillar 管弄 pipe tunnel 舷墙 bulwark 槽形隔舱 corrugated bulkhead 封板 closing plate 螺旋桨 propeller 船底塞 bottom plug 干舷 freeboard 载重线 load line羊角滚轮 fairlead
水平滚轮 roller
27
船体常用英语介绍
导缆滚轮 Roller
导缆孔 Mooring pipe
28
船体常用英语介绍
菌型通风筒 Mushroom ventilator 通风筒 ventilator
29
船体常用英语介绍
舱口盖 hatch cover
导轨
guide way
35
船体常用英语介绍 烟囱 funnel 锚链筒 hawse pipe 锚链舱 chain locker 船台 berth 船坞 dock 坞门 caisson 码头 quay 胎架 jig 污水井 bilge well 吸口 suction 计程仪 log 回声探测 echo sounding 正车 ahead 倒车 astern 纵倾 trim 横倾 heel 纵摇 pitch 横摇 roll 锚地 anchorage 海里 nautical 剪力 shearing force 交变应力 fluctuating stress 拉伸应力 tensile stress 压缩应力 compressive stress
前桅 Fore mast
25
船体常用英语介绍
锚链筒 凸台 Shell flange
锚机 windlass
锚链
船体结构用语中英对照
船体结构用语-中英对照中英文对照船体结构用语: 主船体main hull上层建筑superstructure上甲板/上层连续甲板upper deck船底bottom舷侧broadside艏艉fore and aft舱壁bulkhead水密watertight艏部bow艉部stern/quarter二层甲板second deck平台甲板platform deck桅屋masthouse罗经甲板compass deck驾驶甲板bridge deck船长甲板master deck高级船员甲板office deck艇甲板boat deck船员甲板crew deck机舱engine room货舱cargo hold货舱口cargo hatch压载舱ballast tank深舱deep tank 燃油舱fuel oil tank滑油舱lubricating oil tank淡水舱fresh water tank污油水舱slop tank隔离空舱/干隔舱caisson球鼻艏标志bulbous bow mark/BB mark首侧推器标志bow thruster mark/BT mark吃水标志draft mark甲板线deck line干舷甲板freeboard deck载重线标志load line mark热带淡水载重线tropical fresh water load line/TF夏季淡水载重线fresh water load line/F热带载重线tropical load line/T夏季载重线summer load line/S冬季载重线winter load line北大西洋冬季载重线winter North Atlantic load line/WNA 国际船舶载重线证书international load line certificate吃水指示系统draft indicating system船舶尺度ship dimension最大尺度/全部尺度/周界尺度overall dimension最大长度/全长/总长length overall/LOA最大宽度/全宽extreme breadth最大高度maximum height净空高度air draught船型尺度/型尺度/主持度moulded dimension垂线间长L/length between perpendiculars型宽B/moulded breadth型深D/moulded depth型吃水d/moulded draft登记尺度register dimension登记长度register length登记宽度register breadth登记深度register depth船舶主尺度比dimension ratio船长型宽比L/B , length breadth ratio船长型深比L/D , length depth ratio船长型吃水比L/d , length draft ratio型宽型吃水比B/d , breadth draft ratio型深型吃水比D/d , depth draft ratio重量吨weight tonnage排水量displacement满载排水量dead displacement空船排水量light displacement装载排水量load displacement总载重量deadweight/DW净载重量net deadweight/NDW容积吨/登记吨capacity tonnage总吨位/总吨gross tonnage/GT净吨位net tonnage/NT运河吨位canal tonnage/CT抗沉性floatability全客船passenger vessel客货船passenger-cargo vessel货客船cargo-passenger vessel客滚船ro-ro passenger ship集装箱船container ship箱格导轨系统cellguide system散装货船bulk carrier散装货物bulk cargo舱口围板hatch coaming横剖面cross-section边舱side tank压载舱ballast tank矿砂船ore carrier压载边舱side ballast tank内底板inner bottom plating兼用船combination carrier矿砂/石油两用船，O/O船ore/oil carrier矿砂/散货/石油三用船，OBO船ore/bulk/oil carrier杂货船general cargo ship滚装船roll on/roll off ship , Ro/Ro ship木材船timber carrier冷藏船refrigerated ship多用途船multi-purpose ship液货船liquid cargo ship易燃液体inflammable liquid油船oil tanker污油水舱slop tank液体化学品船liquid chemical tanker液化气船liquefied gas carrier液化天然气船liquefied natural gas carrier/LNG carrier液化石油气船liquefied petroleum gas carrier/LPG carrier 乙烯运输船ethylene tanker工程船engineering ship挖泥船dredger起重船floating crane海洋调查船marine survey ship敷缆船cable ship航标船navigation mark ship工作船working ship拖船tug供应船supply boat破冰船icebreaker海难救助船rescue ship消防船fire boat科学考察船scientific research ship船体结构ship construction钢板plate型钢section steel扁钢flat bar球扁钢bulb bar角钢angle bar , A/B工字钢I-barT型钢T-bar槽钢channel bar铸钢，铸件casting锻钢，锻件forging焊接welding周围焊around welding电弧焊/电焊electric arc welding气焊gas welding焊缝weld塞焊plug welding端接焊end welding角接焊fillet welding对接焊butt welding搭接焊lap welding坡口groove覆板doubling plate铆接riveting板材deals and battens骨架skeleton总纵强度total longitudinal strength 扭转强度torsional strength横向强度transverse strength局部强度local strength坐坞强度docking strength刚度rigidity稳定性stability应力集中stress concentration船台building berth横骨架式transverse framing system 横向构件transverse member舷顶列板sheer strake舷侧板side plating舭列板bilge strake船底板bottom plating中内龙骨center keelson旁内龙骨side keelson梁肘板beam knee平板龙骨(flat) plate keel甲板纵桁deck girder肋骨frame强肋骨web frame舷侧纵桁side girder肋板floor横梁beam横舱壁板transverse bulkhead plating舱容hold capacity外板shell plate内底板inner bottom plating纵向构件longitudinal member自重sole weight纵骨架式longitudinal framing system船底纵骨bottom longitudinal中桁材center girder旁桁材side girder舷顶列板sheer strake舷侧纵骨side longitudinal撑材strut甲板纵骨deck longitudinal强横梁web beam舱口围板hatch coaming纵舱壁longitudinal bulkhead舭龙骨bilge keel二层甲板tween deck内底边板margin plate实肋板/主肋板solid floor内底纵骨inner bottom longitudinal加强筋stiffener人孔manhole舱口端梁hatch end beam支柱pillar船舱肋骨hold frame甲板间肋骨tweendeck frame舷侧列板side strake舭肘板/污水沟三角板bilge bracket 舱口端横梁hatch end beam防倾肘板tripping bracket舷墙板bulwark plating舷强扶强材bulwark stiffener换新renew基本结构图basic construction plan纵中剖面结构图central fore-and-aft plane construction plan各层甲板图deck plan内底结构图inner bottom construction plan列板strake舭列板bilge strake甲板边板deck stringer基线base line横剖面图transverse cross-section plan中横剖面图midship transverse cross-section plan机舱处横剖面图engine-room transverse cross-section plan货舱口处横剖面图cargo hatch transverse cross-section plan舱壁图bulkhead plan总布置图general arrangement plan船底结构bottom construction下甲板横梁lower deck beam上甲板横梁upper deck beam支柱肘板pillar bracket双层底结构double bottom construction骨架framing首防撞舱壁fore collision bulkhead尾尖舱舱壁afterpeak bulkhead肘板bracket水密肋板watertight floor内底纵骨inner bottom longitudinal实肋板solid floor组合肋板/框架肋板bracket floor扶强材side girder船底横骨bottom frame流水孔drain hole透气孔air hole减轻孔lightening hole切口incision内底横骨inner bottom frame水密舱壁watertight bulkhead横骨架式双层底结构transversely framed double bottom construction 轻型肋板lightened floor面板face plate折边flanging中桁材/中底桁center girder中内底板center inner bottom plating箱形中桁材/箱形龙骨duct keel管隧pipe tunnel水密纵桁watertight longitudinal girder 内底纵骨inner bottom longitudinal内底横骨inner bottom frame船底中心线bottom center line旁桁材/旁底桁/旁龙骨side girder人孔盖manhole cover污水沟bilge drainage/side bilge污水井bilge well/bilge sump单层底结构single bottom construction 中内龙骨center keelson旁内龙骨side keelson舷侧外板side plating甲板边板deck stringer主肋骨main frame甲板间肋骨tweendeck frame尖舱肋骨peak frame肋距frame space中间肋骨intermediate frame普通肋骨ordinary frame强肋骨web frame舷侧纵桁side stringer舷侧纵骨side longitudinal舷边gunwale舷边角钢gunwale angle bar止裂crack arrest舷墙bulwark舷墙板bulwark plating支撑肘板buttress bracket扶手armrest栏杆hand rail舱口纵桁hatch side girder甲板纵中线deck center line舱口端梁hatch end beam强力甲板strength deck甲板间舱tweendeck space遮蔽甲板shelter deck舱壁甲板bulkhead deck干舷甲板freeboard deck量吨甲板tonnage deck半梁half beam斜置加强筋tilt stowing stiffener管型支柱tubular pillar水平加强筋horizontal stiffener菱形面板diamond plate悬臂梁cantilever beam梁拱camber舷弧线sheer curve舷弧sheer首舷弧fore sheer尾舷弧after sheer首尖舱fore peak tank首尖舱舱壁fore peak tank bulkhead防撞舱壁collision bulkhead尾尖舱舱壁after peak tank bulkhead防火舱壁fireproof bulkhead液体舱壁liquid bulkhead油密oiltight制荡舱壁wash bulkhead平面舱壁plane bulkhead舱壁板bulkhead plate舱壁扶强材bulkhead stiffener水平桁horizontal girder对称槽形舱壁symmetrical corrugated bulkhead 三角形triangle矩形rectangle梯形trapezoid弧形arc双层底double bottom tank底边舱lower side tank顶边舱top side tank底登lower stool直立型首straight bow首柱stem/stem post驳船barge前倾型首raked bow飞剪型首clipper bow首楼甲板forecastle deck破冰型首ice resistant bow兴波阻力wave making resistance形状阻力form resistance铸钢首柱cast steel stem post钢板首柱steel plate stem post锚链舱chain locker升高肋板raised floor强胸横梁panting beam外板shell plate开孔平台trepanned platform椭圆形尾elliptical stern巡洋舰形尾cruiser stern方型尾transom stern尾封板stern transom plate船首结构bow construction强力构件strength member剖面模数section modulus船尾结构stern construction尾肋板transom floor尾柱底骨sole piece推进器柱propeller post轴毂propeller boss舵钮rudder gudgeon舵柱rudder post斜横梁cant beam舵机舱平台steering gear room platform 尾升高肋板stern raised floor斜肋骨cant frame舵杆管rudder case防火措施fire precaution防火结构fire structure耐火材料refractory material主竖区main vertical zone不燃材料non-combustible material自燃autoignition易燃蒸气inflammable vapour可燃材料combustible material等效材料equivalent material防火分隔fire resisting divisionA级分隔/甲级分隔A class division天花板ceiling衬板furring轴隧shaft tunnel推进器轴propeller shaft逃生孔escape trunk中机型船amidship-engined ship尾机型船stern-engined ship单车船single-screw ship顶板top plating木铺板batten ceiling滑动式水密门slid watertight door拱形顶板arch top plating平顶板flat top plating轴承基座stool supporting shaft bearing管系piping格子板grating舭龙骨/减摇龙骨bilge keel坞修dock repair船底塞docking plug坞墩docking block锰黄铜manganese brass不锈钢stainless steel舭部外板bilge plate舷侧型线moulded line of side shell船底型线moulded line of bottom shell垫圈insertion ring垫板pad隔离空舱caisson双层舷侧double side shell双层壳double shell中间舱center tank边舱side tank甲板下纵桁deck lower girder业务衡准数criterionof service numeral 舱底水管系bilge system舱底水管路bilge pipe吸口suction过滤器filtrator舱底水总管bilge main line止回阀non-return valve舱底泵bilge pump阀箱valve casing泥箱mud box油水分离器oil-water separator测量管/测深管sounding pipe旋塞faucet螺纹盖thread cap防击板striking plate压载管系ballast system压载水ballast water压载管路ballast pipe调驳阀箱control valve easing压载泵ballast pump截止阀stop valve海底阀/通海阀sea suction valve舷侧排水阀overboard discharge valve空气管air pipe花钢板diamond plate自动关闭阀automatic closing valve通风管系ventilating system自然通风natural ventilation烟斗式通风筒cowl-head ventilator排风筒uptake ventilator蘑菇形通风筒mushroom ventilator起重柱Samson post鹅颈式通风筒gooseneck ventilator机械通风mechanical ventilator风机aerator管路pipe conduit吸口空气滤器suction air filter空气调节air conditioning system消防管系fire extinguishing system固定式灭火系统fixed fire extinguishing system水灭火系统water fire extinguishing system气体灭火系统gas fire extinguishing system泡沫灭火系统foam fire extinguishing system水雾灭火系统water fog fire extinguishing system自动喷水系统automatic sprinkling fire extinguishing system 惰性气体保护系统inert gas system日用水管系domestic water supply system日用淡水系统domestic fresh water system日用热水系统domestic warm water system饮用水系统potable water system重力水柜gravity tank压力水柜pressure tank循环泵circulating pump甲板排水管系deck scupper system甲板排水器deck scupper排水管scupper pipe卫生排泄系统sanitary water system锚anchor锚穴anchor recess锚链筒hawse pipe制链器chain stopper锚机windlass锚链管chain pipe锚链舱chain locker锚链chain cable闸刀switch blade制动销detent pin松紧螺丝扣turnbuckle弃链器releasing gear横闩式弃链器dog type cable clench 螺旋弃链器screw type cable releaser 手轮hand wheel螺杆screw脱钩senhouse slip末端链环end open link首锚bow anchor尾锚stern anchor有杆锚/海军锚stocked anchor锚铃环anchor ring锚干anchor shank锚爪anchor fluke锚冠anchor crown锚爪臂anchor arm锚尖anchor bill锚爪掌anchor flukepalm锚杆销forelock pin横杆folding stock无杆锚/山字锚stockless anchor锚卸扣anchor shackle锚肩/助抓突角anchor shoulder销轴pintle横销pin cotter大抓力锚high holding power anchor 普通链环common link加大链环enlarged link末端链环end open link散合式连接链环detachable link肯特卸扣Kenter link转环swivel link电动锚机electric windlass电动液压锚机hydraulic windlass电动机electromotor减速器reducer传动齿轮drive gear离合器clutch链轮chain wheel刹车操纵杆brake control rod带缆卷筒rope drum带式刹车brake绞盘capstan锚机间windlass room锚链末端bitter end舾装数/船具数N/equipment number 备锚spare anchor大抓力锚HHP超大抓力锚SHHP挂锚hanging off an anchor单花cross双花elbow锚链绞缠foul hawse清解锚链cleaning a foul hawse力链riding cable惰链sleeping cable保险缆safety line挂缆hang line送出缆removing rope纤维缆绳fibre rope钢丝缆绳wire rope尼龙绳nylon rope涤纶绳polyester rope丙纶绳polypropylene乙纶绳polyethylene维尼龙绳vinylon rope硬钢丝绳stiff wire rope半硬钢丝绳semi-flexible wire rope 软钢丝绳flexible wire rope钢丝股strand油麻芯股jute heart钢丝wire油麻芯jute or wire core复合缆compound rope破断强度breaking load/BL安全强度safety load安全工作负荷safe working load/SWL试验强度test strength/TS验证负荷proof load/PL头缆/首缆head line尾缆stern line前横缆forward breast line后横缆aft breast line前倒缆/首倒缆fore spring line后倒缆aft spring line单头缆buoy line回头缆slip line吊拖leading ahead巴拿马导缆孔Panama fairlead缆桩bitt/bollard导向滚轮pedestal fairlead万向导缆孔multi-angled fairlead导向滚轮guide roller单十字缆桩single cross bitt羊角桩cleat单柱系缆桩single-post bitt双柱系缆桩double-post bitt斜式双柱系缆桩double raked bitt双十字缆桩double cross bitt导缆孔chock导向滚柱fairlead roller导缆钳fairleader转动导缆器/万向导缆器universal fairlead 水平滚柱horizontal roller垂直滚柱vertical roller基座seating卷筒cable drum挡角horn基座pedestal绞缆机/系缆绞车mooring winch系缆绞盘capstan圆盘刹车disc brake主卷筒main drum减速箱reduction gear box联轴节union joint主轴main shaft滚筒capstan head检查盖inspection cover控制开关control switch接线盒terminal box自动张力绞缆机automatic tension mooring winch 压力调节阀pressure adjusting valve液压泵hydraulic pump卷筒/缆车reel制缆索stopper撇缆绳heaving line撇缆头heaving line ball碰垫/靠把fender防鼠板rat guard撇缆器throwing line apparatus靠泊berthing离泊unberthing乔塞尔公式Joessel平板舵/单板舵single-plate rudder流线型舵streamline rudder舵杆rudder stock连接法兰coupling flange舵臂rudder stay舵板rudder plate舵销rudder pin水平加强筋horizontal stiffener焊接衬板welding bracket垂直加强筋vertical stiffener吊舵孔lifting rudder tube不平衡舵unbalanced rudder平衡舵balanced rudder半平衡舵semi-balanced rudder支承舵bearing rudder多支承舵multi-pintle rudder双支承舵double bearing rudder穿心舵轴平衡舵balanced rudder with axle悬挂舵underhung rudder半悬挂舵partially underhung rudder反应舵/迎流舵reaction rudder主动舵active rudder整流帽舵bulb rudder襟翼舵flettner rudder/flap rudder科特导流管舵Kort nozzle rudder组合舵unit rudder希林舵Schilling rudder舵叶rudder blade固定导流管fixed nozzle可转动导流管movable nozzle翼片fin螺旋桨舵rudder propeller水平法兰连接horizontal coupling joint 垂直法兰连接vertical coupling joint 上轴承upper bearing舵轴rudder axle下轴承lower bearing吊舵孔tube hole骨架肋板webs舵底塞drain plug舵板rudder plate衬套cylinder liner止推滚珠轴承non-return ball bearing 舵承体rudder bearing frame填料packing舵承盖rudder bearer cover挡板shield水密填料watertight packing螺钉screw舵杆衬套stock bushing本体rudder body压盖screw cover滚珠轴承ball bearing底座bed plate蜗杆worm蜗轮worm wheel小齿轮small gear舵扇rudder quadrant缓冲弹簧buffer spring舵柄tiller液缸hydraulic cylinder柱塞ram滑块cod piece动力装置PU/power units换向阀CO/changeover valve溢流阀RV/relief valve锁紧阀LV/locking valve阀门箱VC/valve chest伺服控制SC/servo control辅助泵auxiliary pump固定体/定子stator回转体/转子rotor动叶movable vane压力舱室pressure chamber定叶fixed vane油管路manifold储油箱oil tank舵角限位器rudder angle stopper随动系统follow-up system手柄控制系统/直接控制系统/应急控制系统non-follow-up system 舵轮wheel液缸liquid tank活塞piston轴axle齿条gear rank弹簧spring活塞杆piston lever杠杆lever液压管路hydraulic pipe自动操舵装置控制系统automatic course-keeping control system 自动舵autopilot比例旋钮/舵角调节旋钮rudder adjust微分旋钮/反舵角调节旋钮/速率调节rate adjust灵敏度旋钮/天气调节旋钮/航摆角调节weather adjust航摆角yawing自动改向旋钮course adjust自适应舵adaptive autopilot恒向线rhumb line自动驾驶仪/航迹舵automatic navigation综合导航仪integrated NAV system航路数据routeing data微处理器micro-processing计程仪Log speed船舶动态vessel movement显示器display警报系统alarm system选择开关select switch舵角反馈器rudder angle feedback计划航线navigation plan计划航向predetermined course大圆航法great circle滑车block挂头oval eye车壳steel side plate车带tail strop制动板stopping plate轴spindle滑轮cast-iron sheave车尾tail绞辘tackle辘绳tackle-fall力端running end根端standing end定滑车fixed block动滑车movable block卸扣shackle钩hook眼板eye plate眼环ring plate心环thimble紧索夹/绳头卸扣clamp索头环socket/swaged terminal松紧螺丝扣/花篮螺丝rigging screw起重机/克令吊crane控制室cabin变幅/旋转操纵杆control lever for slewing/luffing 起货操纵杆control lever for hoisting吊臂jib油马达oil motor上油柜head tank过滤器oil strainer冷却器oil cooler限位器箱differential limit switch box变幅绞车luffing winch起货绞车hoisting winch吊货滑车falling block液压千斤顶hydraulic cylinder安全工作负荷safe working load/SWL吊货索cargo fall千斤索topping lift起货机cargo winch千斤索绞车topping lift winch吊杆boom吊货钩cargo hook起重柱Samson post/SP双杆联合union purchase舷内吊杆/大关inside boom舷外吊杆/小关outside boom调整稳索adjustable guy保险稳索insurance guy三角眼板triangle eye-plate吊货索滑车组cargo fall tackle千斤索滑车组topping lift tackle稳索guy导向滑车leading block桅柱mast重型吊杆heavy derrick控制台cross-tree轻型吊杆derrick山字吊货钩Flemish hook连接横杆connecting traverse拉索pull guy滚动式rolling type滚翻式rolling and tipping type舱口围板支架brackets偏心轮eccentric wheel连接链connecting chain上滚轮upper roller压紧器cleat halve上升轨wheel ramp导装面板leading panel折叠式folding type铰链slotted hinge固定钩fixed hook存放臂stowing arm钢索wire pendant铰接滑车hinged sheave拖拽眼板hauling eye plate关闭臂closing arm固定钩securing hook熏舱fumigation《货物系固手册》cargo securing manual/CSM 货物单元cargo unit标准货standardized cargo半标准货semi-standardized cargo非标准货non-standardized cargo货物系固设备cargo securing device系固secure支持support最大系固负荷maximum securing load/MSL 固定式系固设备fixed securing device便携式系固设备portable securing device 地铃lashing eye系固链条lashing chain紧链器tension lever钢丝绳lashing wire rope系固钢带lashing steel band花篮螺丝/松紧螺旋扣turnbuckle系固槽座lashing pot绑扎带lashing band象脚elephant feet拖车支架trailer trestle拖车千斤顶trailer support jack轮楔wheel chock系固钢丝lashing wire快速释放紧索器quick release lashing底座foundation滑移底座sliding foundation埋入式底座imbed foundation燕尾槽/燕尾底座dovetail foundation板式底座doubling plate foundation插座socket固定锥welding cone可折地铃/D形环D-ring眼板lashing plate箱格导轨系统cellguide system横撑材transverse prop导箱构件container guide member横向支撑底座lateral support foundation集装箱绑扎桥lashing bridge扭锁twistlock操作杆operating rod半自动扭锁semi-automatic twistlock锁销locking pin底座扭锁bottom twistlock堆锥stacking cone中间堆锥inter-bridge stacking cone底座堆锥bottom stacking cone可移动锥板removable cone plate自动定位锥automatic fixing cone锁紧装置locking device调整堆锥/高度补偿锥leveling stacking cone桥锁bridge fitting绑扎杆/绑扎棒lashing bar横向撑柱lateral support element辅助工具accessory appliance分舱因数factor of subdivision重心gravity/G稳心metacenter/M船舶修理ship repair计划修理planned repair临时修理occasional repair航修voyage repair小修current repair岁修annual repair检修overhaul船坞dock坞修dock repair事故修理accident repair自修self repair防腐锌板ZINC protector/anticorrosion zinc plate进坞图docking plan舵结构图rudder construction plan浮坞floating dock船底望光light measure with eye for the bottom deforming 裂缝crack止裂孔stopper hole船舶修理单repair list缺陷清单defect list外观检查external examination内部检查internal examination缺陷修补imperfection mend系泊试验docking test密性试验watertight test冲水试验hose testing压水试验water test气密试验gastight test舷梯gangway航行与信号设备navigation and signal equipment通信设备communication equipment倾斜试验inclining test航行试验navigation test加强检验附加标志ESP/Enhanced Survey Program水下检验in-water survey压载水管理计划BWMP/ballast water management plan 入级检验classification survey保持船级检验survey for class maintenance年度检验annual survey中间检验intermediate survey坞内检验docking survey特别检验special survey循环检验continuous survey法定检验statutory survey营运中检验survey for ships in service定期检验periodical survey换证检验change certificate survey附加检验additional survey。
吸力式沉箱基础考虑土体流变效应的p-y曲线法
吸力式沉箱基础考虑土体流变效应的p-y曲线法戴国亮;朱文波;袁龙锦;龚维明;赵学亮【摘要】为了考虑土体流变效应对吸力式沉箱基础承载特性的影响,通过建立理想弹塑性p-y曲线法中土抗力系数与时间变量之间的关系,提出了一种考虑土体流变效应的吸力式沉箱基础长期性能分析方法.基于2组不同水平荷载作用下的长期模型试验,采用Matlab拟合土体参数试验数据,获得关于时间变量的理想弹塑性p-y 曲线模型,并采用该方法对模型试验结果进行分析.结果表明:在长期模型试验中位移与土压力发展主要集中在试验前期,后期位移与土压力稳定需要更长时间,土体流变效应较为明显.理论计算值与实测值随时间变化规律类似,理论计算结果与试验结果相差8%左右,说明长期水平荷载下考虑时间因素的p-y曲线计算结果能较好地吻合试验值.%To consider the soil rheological effects on bearing characteristics of the suction caisson foundation, a long-term performance analysis method for considering the soil rheological effect of the suction caisson foundation is proposed by establishing the relationship between soil resistance coefficients and time variable of the ideal elastic-plastic p-y curve method.Based on two sets of different long-term horizontal load model tests, the ideal elastic-plastic p-y curve model about time variable is obtained by using Matlab to fit the experimental data of soil parameters.Then, the proposed method is used to analyze the results of the model test.Analysis results show that in the long-term model test, the development of displacement and soil pressure are mainly concentrated in the early stage of the experiment;the later displacement and the soil pressure stabilization need longer time, and the soil rheological effect isobvious.The theoretically calculated values and the measured values are similar with the change of time, and the difference between them is about 8%, which show that the calculated results by this method can fit well with the experimental values.【期刊名称】《东南大学学报（自然科学版）》【年(卷),期】2017(047)004【总页数】6页(P806-811)【关键词】吸力式沉箱基础;流变效应;p-y曲线;模型试验【作者】戴国亮;朱文波;袁龙锦;龚维明;赵学亮【作者单位】东南大学土木工程学院, 南京 210096;东南大学混凝土及预应力混凝土结构教育部重点实验室, 南京 210096;东南大学土木工程学院, 南京 210096;东南大学土木工程学院, 南京 210096;东南大学土木工程学院, 南京 210096;东南大学混凝土及预应力混凝土结构教育部重点实验室, 南京 210096;东南大学土木工程学院, 南京 210096;东南大学混凝土及预应力混凝土结构教育部重点实验室, 南京210096【正文语种】中文【中图分类】TU473随着海洋石油资源和海上风能大规模的开发利用,吸力式沉箱基础作为新型的深水海洋基础型式,具有适用于深水和软弱土质等优点,近十年来被广泛地应用于系泊深水海洋设施中．目前,针对水平荷载作用下吸力式沉箱基础承载特性研究中很少有考虑软土流变效应的研究现状,有必要对长期水平荷载作用下吸力式沉箱基础承载特性开展相关理论分析与试验研究．现已有不少关于吸力式沉箱基础水平承载特性方面的试验研究与分析方法．Rajashree等[1]通过离心机试验对吸力式沉箱基础在静、动水平荷载作用下的极限承载力与水平位移进行了研究.孙曦源等[2]结合三维有限元法与极限平衡方法对饱和软黏土地基中吸力式沉箱基础水平承载力进行了研究.刘锟等[3]进行了吸力式沉箱基础在竖向循环荷载作用下的承载特性模型试验．黎冰等[4]对吸力式沉箱基础水平承载力计算方法以及抗拔试验进行了研究.Aubeny等[5-6]推导了吸力式沉箱在不排水条件下受水平荷载作用时承载力的塑性上限分析方法.McClelland 等[7]就试桩的实测反力-变位提出p-y曲线法.文献[8-16]又对p-y曲线法进行改进,其中较著名的是p-y曲线合成法.此后许多规范采用和推广了该方法.p-y曲线考虑了土的非线性反应,既可用于小位移情况的求解,也可用于大位移,现已成为国外计算推力桩最为流行的方法之一.然而上述关于吸力式沉箱基础的研究中,考虑软土流变效应的研究较少.考虑流变效应的p-y曲线法的理论计算仍处于空白阶段,因此本文对长期水平荷载作用下吸力式沉箱基础承载特性进行了理论分析与试验研究．首先,通过引入时间变量t对理想弹塑性p-y曲线法进行修正．然后,采用Matlab拟合2组不同水平荷载作用下的长期模型试验数据,建立理想弹塑性p-y曲线中土体抗力系数k与时间变量t之间的关系式,得出关于时间变量的理想弹塑性p-y曲线模型.最后,采用该方法对模型试验结果进行分析.长期水平荷载作用下吸力式沉箱的理论计算方法并未考虑时间效应下土体性质的变化对计算结果的影响.因此,本文将选取理想弹塑性p-y曲线法,把理想弹塑性p-y曲线法中土抗力系数k随着时间的衰减过程看作是土体流变效应的变化过程.首先建立不同深度z处土抗力系数k(z,t)与土体参数c(t)的关系,其次采用Matlab拟合土体参数试验数据,得到土体参数c(t)的表达式,最后获得关于时间变量的理想弹塑性p-y曲线模型.理想弹塑性p-y曲线法计算公式如下:式中,p为水平土抗力;pu为极限水平土抗力;D为模型直径;y为水平位移;yu为单位长度土体临界位移,m;Ng为极限抗力系数;α0为等效土体深度,m;m为极限土抗力的形状参数;z为埋深,m;k为土抗力系数,kN/m3. 理想弹塑性p-y曲线如图1所示．因此,对于不同时间t时深度z处的土抗力系数k(z,t)有式中,yz,pz分别为沉箱基础不同深度z处各点的水平位移值与单位面积土抗力值．由2组不同水平荷载作用下的长期模型试验,可以测得yz与pz,进而得到土抗力系数k(z,t).为了建立k(z,t)与土体参数c(t)的关系,并考虑不同深度z对水平抗力系数的影响,参照随深度分布的常用形式,提出如下假设:式中,n根据试验结果确定.因此,对于不同时间t时不同深度z处,基础周围土抗力p(z,y,t)可表示为由式(5)可得根据吸力式沉箱基础试验数据可得到不同深度z处的土抗力p值与对应的水平位移y值,将它们代入式(6),计算得出在不同时间t时不同深度z处的土体参数c值.然后采用Matlab进行非线性拟合,得出关于时间t的土体参数表达式,代入式(5)中可得关于时间参数的理想弹塑性p-y曲线.为了考虑土体流变效应对吸力式沉箱承载特性的影响,进行了1组短期模型试验和2组不同水平荷载作用下吸力式沉箱基础长期模型试验,对吸力式沉箱基础随时间的位移变化规律以及土压力分布规律进行了研究,并通过模型试验得到关于不同时间t时的土体参数c(t).本文试验中所用吸力式沉箱模型为钢制沉箱.模型沉箱内外壁光滑,下部敞开,上部采用可拆卸钢板,顶盖密封并设置2个穿线孔,便于土压力计等测试元件线路的引出.模型沉箱壁和顶板厚均为20 mm,沉箱外直径D为500 mm,高L为800 mm,质量为216 kg.沉箱模型如图2所示.由于吸力式沉箱模型的尺寸较大,因此采用预埋式,分别将土分层平铺于箱内外并夯实.对夯实的土层进行洒水饱和后,进行排水固结.当孔隙水压力数据稳定并测量到土体每小时沉降量不大于0.005 mm时,认定土体固结完成.在加入下一层试验土之前凿毛上层表面土,重复每层土体制备过程直至试验要求土体深度.制备好土体后,采用固结不排水剪切试验测得内摩擦角与黏聚力分别为18.2°和27.5 kPa.孔隙水压力计、土压力计、百分表的布置以及加载装置和沉箱模型尺寸如图3所示.经短期模型实验测得吸力式沉箱基础极限承载力Pu为5 kN.在长期水平荷载作用下2种不同工况的荷载取值分别为0.5Pu和0.6Pu,每一级施加荷载约为长期水平荷载值的10%左右,当荷载稳定后施加下一级荷载.水平荷载加载到0.5Pu或0.6Pu 时,连续观测20 d,并记录相关百分表与土压力计数据.试验得到的位移-时间曲线如图4所示.在2.5 kN长期模型试验中,前150 h土面水平位移增加了1.123 mm,之后水平位移增加趋势平缓,土面水平位移趋于稳定值4.227 mm,与初期水平位移值2.660 mm相比,流变变形为1.567 mm,达到58.91%;3.0 kN长期模型试验中,前150 h土面水平位移增加了1.629 mm,之后水平位移增加趋势平缓,约250 h以后土面水平位移趋于稳定值6.165 mm,与初期水平位移值4.216 mm相比,流变变形为1.949 mm,达到46.23%.可见在长期水平荷载作用下考虑土体的流变效应比较符合实际情况.2.5 kN长期荷载作用下基础后侧土压力与时间关系如图5(a)所示,深度600mm(z/L=0.75)处及以上测点为主动土压力,深度750 mm(z/L=0.94)附近土压力为被动土压力.图4(b)反映了基础前侧土压力变化情况,随着时间的增加不同土压力有不同程度的增大,深度300 mm(z/L=0.38)附近的被动土压力最大,从试验初期的11.97 kPa增大到14.58 kPa,增大趋势明显.图6为不同深度沉箱后侧与前侧土压力随时间的变化趋势.曲线均近似呈抛物线分布,表明沉箱基础在水平荷载作用下为转动模式.土压力发展主要集中在试验前期,后期土压力变化相对较小,所需时间较长.图7反映了不同深度处土压力与水平位移之间的变化关系,即p-y曲线．在加载阶段,不同深度处的曲线表现为类似线性增长.当水平位移增大到一定程度时,土压力基本保持不变.由试验中的水平位移值yz与单位面积土抗力值pz,可以得到不同t时刻土抗力系数k与深度z的曲线图.图8给出了0时刻的拟合曲线,可看出土抗力系数k与深度z之间的关系并非呈线性关系.通过对不同时刻t的拟合计算,可知当拟合曲线中土抗力系数k与深度z1/2成正比时,拟合度较好,因此可假定指数n=1/2,此时相关系数R2=0.94.将n=1/2代入式(5),可得将试验测得的4个深度处(z=100, 200, 300, 500 mm)的土抗力值p与对应的水平位移值y代入式(7),得出不同时间t时不同深度z处的土体参数c值,采用Matlab 对不同c值进行非线性拟合,具体拟合结果如图9所示.由曲线拟合结果得在长期荷载不变时,考虑土体流变效应,不同时间t时不同深度z处,土体的p-y曲线关系式如下:式中,c0为主固结完成时初始土体参数,本试验取值为c0=9.6 MN/m3.5;a1为土性衰减拟合参数,取值为a1=0.205.式(9)为P≤Pu时p-y曲线关系式, Pu值按照理想弹塑性p-y曲线的公式计算.在不同长期水平荷载作用下,p-y曲线表达式与长期试验荷载值相关,因此将加载值大小这一因素予以适当考虑,有利于提高计算结果的可靠性.在长期荷载作用下,土体的土体参数随时间的变化规律相似,但是土性的衰减速率会有所不同,即式(9)中的参数a1与长期试验下的加载值有关．对3.0 kN长期荷载作用下土体参数c衰减进行拟合,结果如图10所示,由图可得初始土体参数为c0=10.2 MN/m3.5,衰减拟合参数a1=0.205.根据2次长期模型试验拟合得到的参数值c0和a1可知,2次拟合c0值相差5%,可认为初始土体参数值c0不受加载值大小影响,基本保持不变．但是3.0 kN作用下模型试验拟合a1值是2.5 kN作用下拟合a1值的1.15倍,说明随着荷载的增大,土体参数c的衰减速率增加.经过上述修正后的理想弹塑性p-y曲线表达式如下:通过现场试验或室内土工试验确定不同时间、不同加载水平、不同埋深以及不同基础尺寸下的极限水平土抗力pu与土体临界位移yu,就能将该计算方法较方便地用于实际工程分析.采用理想弹塑性p-y曲线法,在LPILE软件中输入不同时间点处由试验数据得到的土抗力p与水平位移y.求得2.5和3.0 kN加载值下不同时间点的沉箱基础模型土面处水平位移值，结果如图11所示.由图11可知:不同荷载作用下,理论计算值与实测值随时间的变化规律类似,说明该理论计算方法可行;2.5 kN荷载作用下，随着时间的增加,理论值与实测值之间的偏差在10%左右;3.0 kN荷载作用下,不同时间两者的偏差均在8%左右.这说明该方法计算的结果能较好地吻合试验值.为了考虑土体流变效应对吸力式沉箱基础承载特性的影响,通过引入时间变量t对理想弹塑性p-y曲线法进行修正,采用Matlab拟合2组不同水平荷载作用下的长期模型试验数据,建立理想弹塑性p-y曲线中土抗力系数k与时间变量t之间的关系式,得出关于时间变量的理想弹塑性p-y曲线模型.并采用该方法对模型试验结果进行分析.试验与分析结果表明:理论计算值与试验值随时间的变化规律类似,考虑时间因素的p-y曲线表达式计算的结果能较好地吻合试验值.【相关文献】[1]Rajashree S S, Sitharam T G. Nonlinear finite-element modeling of batter piles under lateral load[J]. Journal of Geotechnical and Geoenvironmental Engineering, 2001, 127(7): 604-612. DOI:10.1061/(asce)1090-0241(2001)127:7(604).[2]孙曦源, 栾茂田, 唐小微. 饱和软黏土地基中桶形基础水平承载力研究[J]. 岩土力学, 2010, 31(2): 667-672. DOI:10.3969/j.issn.1000-7598.2010.02.056. Sun Xiyuan, Luan Maotian, Tang Xiaowei. Study of horizontal bearing capacity of bucket foundation on saturated soft clay ground[J]. Rock and Soil Mechanics, 2010, 31(2): 667-672. DOI:10.3969/j.issn.1000-7598.2010.02.056.(in Chinese)[3]刘锟,赵春风,王建华.软土地基桶形基础室内模型试验研究[J].地下空间与工程学报,2010,6(3):477-480. DOI:10.3969/j.issn.1673-0836.2010.03.008. Liu Kun, Zhao Chunfeng, Wang Jianhua. Model test study of bucket foundation on soft clay strata[J]. Chinese Journal of Underground Space and Engineering, 2010, 6(3): 477-480.DOI:10.3969/j.issn.1673-0836.2010.03.008.(in Chinese)[4]黎冰, 高玉峰, 沙成明, 等. 砂土中吸力式沉箱基础的最大承载力计算方法[J]. 东南大学学报(自然科学版), 2012, 42(6): 1201-1205. DOI:10.3969/j.issn.1001-0505.2012.06.032. Li Bing, Gao Yufeng, Sha Chengming, et al. Calculation method for maximum bearing capacity of suction caisson foundation in sand[J]. Journal of Southeast University(Natural Science Edition), 2012, 42(6): 1201-1205. DOI:10.3969/j.issn.1001-0505.2012.06.032.(in Chinese) [5]Aubeny C P, Han S W, Murff J D. Inclined load capacity of suction caissons[J]. International Journal for Numerical and Analytical Methods in Geomechanics, 2003, 27(14): 1235-1254. DOI:10.1002/nag.319.[6]Aubeny C P, Murff J D, Moon S K. Lateral undrained resistance of suction caisson anchors[J].International Journal of Offshore and Polar Engineering, 2001, 11(3):211-219. [7]McClelland B, Focht J A. Soil modulus of laterally loaded piles[J]. Transactions of the American Society of Civil Engineers, 1958, 123:1049-1063.[8]张永涛,杨炎华,黎冰,等. 桥梁吸力式沉箱基础承载特性试验研究[J]. 岩土工程学报,2015,37(1):177-182. Zhang Yongtao, Yang Yanhua, Li Bing, et al. Model tests on bearing performance of suction caisson foundation for bridges[J]. Chinese Journal of Geotechnical Engineering 2015, 37(1):177-182.[9]Reese L C, Koop F D. Analysis of laterally loaded piles in sand[C]//Offshore Technology in Civil Engineering Hall of Fame Papers from the Early Years. Dallas, TX, USA, 1974: 95-105. DOI:10.4043/2080-ms.[10]Dunnavant T W, ONeill M W. Experimental p-y model for submerged, stiff clay[J]. Journal of Geotechnical Engineering, 1989, 115(1): 95-114. DOI:10.1061/(asce)0733-9410(1989)115:1(95).[11]Gabr M A, Lunne T, Powell J J. P-y analysis of laterally loaded piles in clay usingDMT[J]. Journal of Geotechnical Engineering, 1994, 120(5): 816-837.DOI:10.1061/(asce)0733-9410(1994)120:5(816).[12]Rollins K M, Hales L J, Ashford S A, et al. P-y curves for large diameter shafts in liquefied sand from blast liquefaction tests[J]. Seismic Performance and Simulation of Pile Foundations in Liquefied and Laterally Spreading Ground, 2006, 2:11-23.DOI:10.1061/40822(184)2.[13]Tokimatsu K, Suzuki H. Pore water pressure response around pile and its effects on p-y behavior during soil liquefaction[J]. Soils and Foundations, 2004, 44(6): 101-110.DOI:10.3208/sandf.44.6-101.[14]凌道盛,任涛,王云岗.砂土地基斜桩水平承载特性p-y曲线法[J].岩土力学,2013,34(1): 155-162. Ling Daosheng, Ren Tao, Wang Yungang. A p-y curve method for horizontal bearing characteristics of single batter pile in sands [J]. Rock and Soil Mechanics, 2013, 34 (1): 155-162. (in Chinese)[15]孙冬梅.长期水平荷载作用下吸力式沉箱基础承载性能试验研究[D].南京:东南大学土木工程学院,2015.[16]李旭.长期水平荷载作用下沉井基础的变位特性研究[D].南京:东南大学土木工程学院,2015.。
船体结构中英文对照表!!很全了,干船舶这一行的都能用得着。
船体结构中英文对照表！！很全了，干船舶这一行的都能用得着。
中英文对照船体结构主船体main hull上层建筑superstructure上层连续甲板upper deck船底bottom舷侧broadside艏艉fore and aft舱壁bulkhead水密watertight艏部bow艉部stern/quarter二层甲板second deck平台甲板platform deck桅屋masthouse罗经甲板compass deck驾驶甲板bridge deck船长甲板master deck高级船员甲板office deck艇甲板boat deck船员甲板crew deck机舱engine room货舱cargo hold货舱口cargo hatch 压载舱ballast tank 深舱deep tank 燃油舱fuel oil tank 滑油舱lubricating oil tank淡水舱fresh water tank污油水舱slop tank 隔离空舱/干隔舱caisson球鼻艏标志bulbous bow mark/BB mark首侧推器标志 bow thruster mark/BT mark吃水标志draft mark甲板线deck line 干舷甲板freeboard deck载重线标志load line mark热带淡水载重线 tropical fresh water load line/TF夏季淡水载重线 fresh water load line/F热带载重线 tropical load line/T夏季载重线 summer load line/S冬季载重线winter load line北大西洋冬季载重线 winter North Atlantic load line/WNA国际船舶载重线证书 international load line certificate吃水指示系统 draft indicating system船舶尺度ship dimension最大尺度/全部尺度/周界尺度 overall dimension最大长度/全长/总长 length overall/LOA最大宽度/全宽 extreme breadth最大高度maximum height净空高度air draught船型尺度/型尺度/主持度 moulded dimension垂线间长 L/length between perpendiculars型宽B/moulded breadth型深D/moulded depth型吃水d/moulded draft登记尺度register dimension登记长度register length登记宽度register breadth登记深度register depth船舶主尺度比dimension ratio船长型宽比L/B , length breadth ratio 船长型深比L/D , length depth ratio船长型吃水比L/d , length draft ratio型宽型吃水比B/d , breadth draft ratio型深型吃水比D/d , depth draft ratio重量吨weight tonnage排水量displacement满载排水量dead displacement空船排水量light displacement装载排水量load displacement总载重量deadweight/DW净载重量 net deadweight/NDW容积吨/登记吨capacity tonnage总吨位/总吨gross tonnage/GT净吨位net tonnage/NT运河吨位canal tonnage/CT抗沉性floatability全客船passenger vessel客货船passenger-cargo vessel货客船cargo-passenger vessel客滚船ro-ro passenger ship集装箱船container ship箱格导轨系统 cellguide system散装货船bulk carrier散装货物bulk cargo舱口围板hatch coaming横剖面cross-section边舱side tank 压载舱ballast tank矿砂船ore carrier 压载边舱side ballast tank内底板inner bottom plating兼用船 combination carrier矿砂/石油两用船 O/O船， ore/oil carrier矿砂/散货/石油三用船 OBO船， ore/bulk/oil carrier杂货船general cargo ship滚装船roll on/roll off ship , Ro/Ro ship木材船timber carrier冷藏船refrigerated ship多用途船multi-purpose ship液货船liquid cargo ship易燃液体inflammable liquid油船oil tanker污油水舱slop tank液体化学品船liquid chemical tanker液化气船liquefied gas carrier液化天然气船liquefied natural gas carrier/LNG carrier 液化石油气船 liquefied petroleum gas carrier/LPG carrier 乙烯运输船ethylene tanker工程船engineering ship挖泥船dredger起重船floating crane海洋调查船marine survey ship敷缆船cable ship航标船navigation mark ship工作船working ship拖船tug供应船supply boat破冰船icebreaker海难救助船rescue ship消防船fire boat科学考察船 scientific research ship船体结构ship construction钢板plate 型钢section steel扁钢flat bar 球扁钢bulb bar角钢angle bar , A/B工字钢I-bar T型钢T-bar槽钢channel bar铸钢，铸件casting锻钢，锻件forging焊接welding 周围焊around welding电弧焊/电焊 electric arc welding气焊gas welding焊缝weld 塞焊plug welding端接焊end welding角接焊fillet welding对接焊butt welding搭接焊lap welding坡口groove 覆板doubling plate铆接riveting 板材deals and battens骨架skeleton 总纵强度total longitudinal strength 扭转强度torsional strength横向强度transverse strength局部强度local strength坐坞强度docking strength刚度rigidity 稳定性stability 应力集中stress concentration船台building berth横骨架式transverse framing system横向构件transverse member舷顶列板sheer strake舷侧板side plating舭列板bilge strake船底板bottom plating中内龙骨center keelson旁内龙骨side keelson梁肘板beam knee平板龙骨(flat) plate keel甲板纵桁deck girder肋骨frame强肋骨web frame舷侧纵桁side girder肋板floor 横梁beam横舱壁板transverse bulkhead plating舱容hold capacity外板shell plate内底板inner bottom plating纵向构件longitudinal member自重sole weight纵骨架式longitudinal framing system船底纵骨bottom longitudinal中桁材center girder旁桁材side girder舷顶列板sheer strake舷侧纵骨side longitudinal撑材strut 甲板纵骨deck longitudinal强横梁web beam舱口围板hatch coaming纵舱壁longitudinal bulkhead舭龙骨bilge keel二层甲板tween deck内底边板margin plate实肋板/主肋板 solid floor内底纵骨 inner bottom longitudinal加强筋 stiffener人孔 manhole舱口端梁 hatch end beam支柱 pillar船舱肋骨 hold frame甲板间肋骨 tweendeck frame舷侧列板 side strake舭肘板/污水沟三角板 bilge bracket舱口端横梁 hatch end beam防倾肘板 tripping bracket舷墙板 bulwark plating舷强扶强材 bulwark stiffener换新 renew基本结构图 basic construction plan纵中剖面结构图 central fore-and-aft plane construction plan 各层甲板图 deck plan内底结构图 inner bottom construction plan列板 strake舭列板 bilge strake甲板边板 deck stringer基线 base line横剖面图 transverse cross-section plan中横剖面图midship transverse cross-section plan 机舱处横剖面图 engine-room transverse cross-section plan货舱口处横剖面图 cargo hatch transverse cross-section plan舱壁图 bulkhead plan总布置图 general arrangement plan船底结构 bottom construction下甲板横梁 lower deck beam上甲板横梁 upper deck beam支柱肘板 pillar bracket双层底结构 double bottom construction骨架 framing首防撞舱壁 fore collision bulkhead尾尖舱舱壁 afterpeak bulkhead肘板 bracket水密肋板 watertight floor内底纵骨 inner bottom longitudinal实肋板 solid floor组合肋板/框架肋板 bracket floor扶强材 side girder船底横骨 bottom frame流水孔 drain hole透气孔 air hole减轻孔 lightening hole切口 incision内底横骨 inner bottom frame水密舱壁 watertight bulkhead横骨架式双层底结构 transversely framed double bottom construction 轻型肋板 lightened floor面板 face plate折边 flanging中桁材/中底桁 center girder中内底板 center inner bottom plating箱形中桁材/箱形龙骨 duct keel管隧 pipe tunnel水密纵桁 watertight longitudinal girder内底纵骨 inner bottom longitudinal内底横骨 inner bottom frame船底中心线 bottom center line旁桁材/旁底桁/旁龙骨 side girder人孔盖 manhole cover污水沟 bilge drainage/side bilge污水井 bilge well/bilge sump单层底结构 single bottom construction中内龙骨 center keelson旁内龙骨 side keelson舷侧外板 side plating甲板边板 deck stringer主肋骨 main frame甲板间肋骨 tweendeck frame 尖舱肋骨 peak frame肋距 frame space中间肋骨 intermediate frame 普通肋骨 ordinary frame强肋骨 web frame舷侧纵桁 side stringer舷侧纵骨 side longitudinal 舷边 gunwale舷边角钢 gunwale angle bar 止裂 crack arrest舷墙 bulwark舷墙板 bulwark plating支撑肘板 buttress bracket 扶手 armrest栏杆 hand rail舱口纵桁 hatch side girder 甲板纵中线 deck center line 舱口端梁 hatch end beam强力甲板 strength deck甲板间舱 tweendeck space遮蔽甲板 shelter deck舱壁甲板 bulkhead deck干舷甲板 freeboard deck量吨甲板 tonnage deck半梁 half beam斜置加强筋 tilt stowing stiffener 管型支柱 tubular pillar水平加强筋 horizontal stiffener菱形面板 diamond plate悬臂梁 cantilever beam梁拱 camber舷弧线 sheer curve舷弧 sheer首舷弧 fore sheer尾舷弧 after sheer首尖舱 fore peak tank首尖舱舱壁 fore peak tank bulkhead 防撞舱壁 collision bulkhead尾尖舱舱壁 after peak tank bulkhead 防火舱壁 fireproof bulkhead液体舱壁 liquid bulkhead油密 oiltight制荡舱壁 wash bulkhead平面舱壁 plane bulkhead舱壁板 bulkhead plate舱壁扶强材 bulkhead stiffener水平桁 horizontal girder对称槽形舱壁 symmetrical corrugated bulkhead 三角形 triangle矩形 rectangle梯形 trapezoid弧形 arc双层底 double bottom tank底边舱 lower side tank顶边舱 top side tank底登 lower stool直立型首 straight bow首柱 stem/stem post驳船 barge前倾型首 raked bow飞剪型首 clipper bow首楼甲板 forecastle deck破冰型首 ice resistant bow兴波阻力 wave making resistance形状阻力 form resistance铸钢首柱 cast steel stem post钢板首柱 steel plate stem post锚链舱 chain locker升高肋板 raised floor强胸横梁 panting beam外板 shell plate开孔平台 trepanned platform椭圆形尾 elliptical stern巡洋舰形尾 cruiser stern方型尾 transom stern尾封板 stern transom plate船首结构 bow construction强力构件 strength member剖面模数 section modulus船尾结构 stern construction尾肋板 transom floor尾柱底骨 sole piece推进器柱 propeller post轴毂 propeller boss舵钮 rudder gudgeon舵柱 rudder post斜横梁 cant beam舵机舱平台 steering gear room platform 尾升高肋板 stern raised floor斜肋骨 cant frame舵杆管 rudder case防火措施 fire precaution防火结构 fire structure耐火材料 refractory material主竖区 main vertical zone不燃材料 non-combustible material自燃 autoignition易燃蒸气 inflammable vapour可燃材料 combustible material等效材料 equivalent material防火分隔 fire resisting divisionA级分隔/甲级分隔 A class division天花板 ceiling衬板 furring轴隧 shaft tunnel推进器轴 propeller shaft逃生孔 escape trunk中机型船 amidship-engined ship尾机型船 stern-engined ship单车船 single-screw ship顶板 top plating木铺板 batten ceiling滑动式水密门 slid watertight door拱形顶板 arch top plating平顶板 flat top plating轴承基座 stool supporting shaft bearing管系 piping格子板 grating舭龙骨/减摇龙骨 bilge keel坞修 dock repair船底塞 docking plug坞墩 docking block锰黄铜 manganese brass不锈钢 stainless steel舭部外板 bilge plate舷侧型线 moulded line of side shell船底型线 moulded line of bottom shell 垫圈 insertion ring垫板 pad隔离空舱 caisson双层舷侧 double side shell双层壳 double shell中间舱 center tank边舱 side tank甲板下纵桁 deck lower girder业务衡准数criterion of service numeral 舱底水管系 bilge system舱底水管路 bilge pipe吸口 suction过滤器 filtrator舱底水总管 bilge main line止回阀 non-return valve舱底泵 bilge pump阀箱 valve casing泥箱 mud box油水分离器 oil-water separator测量管/测深管 sounding pipe旋塞 faucet螺纹盖 thread cap防击板 striking plate压载管系 ballast system压载水 ballast water压载管路 ballast pipe调驳阀箱 control valve easing压载泵 ballast pump截止阀 stop valve海底阀/通海阀 sea suction valve舷侧排水阀 overboard discharge valve 空气管 air pipe花钢板 diamond plate自动关闭阀 automatic closing valve 通风管系 ventilating system自然通风 natural ventilation烟斗式通风筒 cowl-head ventilator排风筒 uptake ventilator蘑菇形通风筒 mushroom ventilator起重柱 Samson post鹅颈式通风筒 gooseneck ventilator机械通风 mechanical ventilator风机 aerator管路 pipe conduit吸口空气滤器 suction air filter空气调节 air conditioning system消防管系 fire extinguishing system固定式灭火系统 fixed fire extinguishing system水灭火系统 water fire extinguishing system气体灭火系统 gas fire extinguishing system泡沫灭火系统 foam fire extinguishing system水雾灭火系统 water fog fire extinguishing system自动喷水系统 automatic sprinkling fire extinguishing system 惰性气体保护系统 inert gas system日用水管系 domestic water supply system日用淡水系统 domestic fresh water system日用热水系统 domestic warm water system饮用水系统 potable water system重力水柜 gravity tank压力水柜 pressure tank循环泵 circulating pump甲板排水管系 deck scupper system 甲板排水器 deck scupper排水管 scupper pipe卫生排泄系统 sanitary water system 锚 anchor锚穴 anchor recess锚链筒 hawse pipe制链器 chain stopper锚机 windlass锚链管 chain pipe锚链舱 chain locker锚链 chain cable闸刀 switch blade制动销 detent pin松紧螺丝扣 turnbuckle弃链器 releasing gear横闩式弃链器 dog type cable clench 螺旋弃链器 screw type cable releaser 手轮 hand wheel螺杆 screw脱钩 senhouse slip末端链环 end open link首锚 bow anchor尾锚 stern anchor有杆锚/海军锚 stocked anchor锚铃环 anchor ring锚干 anchor shank锚爪 anchor fluke锚冠 anchor crown锚爪臂 anchor arm锚尖 anchor bill锚爪掌 anchor flukepalm锚杆销 forelock pin横杆 folding stock无杆锚/山字锚 stockless anchor锚卸扣 anchor shackle锚肩/助抓突角 anchor shoulder销轴 pintle横销 pin cotter大抓力锚 high holding power anchor 普通链环 common link加大链环 enlarged link末端链环 end open link散合式连接链环 detachable link肯特卸扣 Kenter link转环 swivel link电动锚机 electric windlass电动液压锚机 hydraulic windlass电动机 electromotor减速器 reducer传动齿轮 drive gear离合器 clutch链轮 chain wheel刹车操纵杆 brake control rod带缆卷筒 rope drum带式刹车 brake绞盘 capstan锚机间 windlass room锚链末端 bitter end舾装数/船具数 N/equipment number 备锚 spare anchor大抓力锚 HHP超大抓力锚 SHHP挂锚 hanging off an anchor单花 cross双花 elbow锚链绞缠 foul hawse清解锚链 cleaning a foul hawse 力链 riding cable惰链 sleeping cable保险缆 safety line挂缆 hang line送出缆 removing rope纤维缆绳 fibre rope钢丝缆绳 wire rope尼龙绳 nylon rope涤纶绳 polyester rope丙纶绳 polypropylene乙纶绳 polyethylene维尼龙绳 vinylon rope硬钢丝绳 stiff wire rope半硬钢丝绳 semi-flexible wire rope 软钢丝绳 flexible wire rope钢丝股 strand油麻芯股 jute heart钢丝 wire油麻芯 jute or wire core复合缆 compound rope破断强度 breaking load/BL安全强度 safety load安全工作负荷 safe working load/SWL 试验强度 test strength/TS验证负荷 proof load/PL头缆/首缆 head line尾缆 stern line前横缆 forward breast line后横缆 aft breast line前倒缆/首倒缆 fore spring line后倒缆 aft spring line单头缆 buoy line回头缆 slip line吊拖 leading ahead巴拿马导缆孔 Panama fairlead缆桩 bitt/bollard导向滚轮 pedestal fairlead万向导缆孔 multi-angled fairlead导向滚轮 guide roller单十字缆桩 single cross bitt羊角桩 cleat单柱系缆桩 single-post bitt双柱系缆桩 double-post bitt斜式双柱系缆桩 double raked bitt双十字缆桩 double cross bitt导缆孔 chock导向滚柱 fairlead roller导缆钳 fairleader转动导缆器/万向导缆器 universal fairlead 水平滚柱 horizontal roller垂直滚柱 vertical roller基座 seating卷筒 cable drum挡角 horn基座 pedestal绞缆机/系缆绞车 mooring winch系缆绞盘 capstan圆盘刹车 disc brake主卷筒 main drum减速箱 reduction gear box联轴节 union joint主轴 main shaft滚筒 capstan head检查盖 inspection cover控制开关 control switch接线盒 terminal box自动张力绞缆机 automatic tension mooring winch 压力调节阀 pressure adjusting valve液压泵 hydraulic pump卷筒/缆车 reel制缆索 stopper撇缆绳 heaving line撇缆头 heaving line ball碰垫/靠把 fender防鼠板 rat guard撇缆器 throwing line apparatus靠泊 berthing离泊 unberthing乔塞尔公式 Joessel平板舵/单板舵 single-plate rudder流线型舵 streamline rudder舵杆 rudder stock连接法兰 coupling flange舵臂 rudder stay舵板 rudder plate舵销 rudder pin水平加强筋 horizontal stiffener焊接衬板 welding bracket垂直加强筋 vertical stiffener吊舵孔 lifting rudder tube不平衡舵 unbalanced rudder平衡舵 balanced rudder半平衡舵 semi-balanced rudder支承舵 bearing rudder多支承舵 multi-pintle rudder双支承舵 double bearing rudder穿心舵轴平衡舵 balanced rudder with axle 悬挂舵 underhung rudder半悬挂舵 partially underhung rudder反应舵/迎流舵 reaction rudder主动舵 active rudder整流帽舵 bulb rudder襟翼舵 flettner rudder/flap rudder科特导流管舵 Kort nozzle rudder组合舵 unit rudder希林舵 Schilling rudder舵叶 rudder blade固定导流管 fixed nozzle可转动导流管 movable nozzle翼片 fin螺旋桨舵 rudder propeller水平法兰连接 horizontal coupling joint 垂直法兰连接 vertical coupling joint 上轴承 upper bearing舵轴 rudder axle下轴承 lower bearing吊舵孔 tube hole骨架肋板 webs舵底塞 drain plug舵板 rudder plate衬套 cylinder liner止推滚珠轴承 non-return ball bearing 舵承体 rudder bearing frame填料 packing舵承盖 rudder bearer cover 挡板 shield水密填料 watertight packing 螺钉 screw舵杆衬套 stock bushing本体 rudder body压盖 screw cover滚珠轴承 ball bearing底座 bed plate蜗杆 worm蜗轮 worm wheel小齿轮 small gear舵扇 rudder quadrant缓冲弹簧 buffer spring舵柄 tiller液缸 hydraulic cylinder柱塞 ram滑块 cod piece动力装置 PU/power units换向阀 CO/changeover valve 溢流阀 RV/relief valve锁紧阀 LV/locking valve阀门箱 VC/valve chest伺服控制 SC/servo control辅助泵 auxiliary pump固定体/定子 stator回转体/转子 rotor动叶 movable vane压力舱室 pressure chamber定叶 fixed vane油管路 manifold储油箱 oil tank舵角限位器 rudder angle stopper随动系统 follow-up system手柄控制系统/直接控制系统/应急控制系统 non-follow-up system 舵轮 wheel液缸 liquid tank活塞 piston轴 axle齿条 gear rank弹簧 spring活塞杆 piston lever杠杆 lever液压管路 hydraulic pipe自动操舵装置控制系统 automatic course-keeping control system 自动舵 autopilot比例旋钮/舵角调节旋钮 rudder adjust微分旋钮/反舵角调节旋钮/速率调节 rate adjust灵敏度旋钮/天气调节旋钮/航摆角调节 weather adjust 航摆角 yawing自动改向旋钮 course adjust自适应舵 adaptive autopilot恒向线 rhumb line自动驾驶仪/航迹舵 automatic navigation综合导航仪 integrated NAV system航路数据 routeing data微处理器 micro-processing计程仪 Log speed船舶动态 vessel movement显示器 display警报系统 alarm system选择开关 select switch舵角反馈器 rudder angle feedback计划航线 navigation plan计划航向 predetermined course大圆航法 great circle滑车 block挂头 oval eye车壳 steel side plate车带 tail strop制动板 stopping plate轴 spindle滑轮 cast-iron sheave车尾 tail绞辘 tackle辘绳 tackle-fall力端 running end根端 standing end定滑车 fixed block动滑车 movable block卸扣 shackle钩 hook眼板 eye plate眼环 ring plate心环 thimble紧索夹/绳头卸扣 clamp索头环 socket/swaged terminal松紧螺丝扣/花篮螺丝 rigging screw起重机/克令吊 crane控制室 cabin变幅/旋转操纵杆 control lever for slewing/luffing 起货操纵杆 control lever for hoisting吊臂 jib油马达 oil motor 上油柜 head tank过滤器 oil strainer冷却器 oil cooler限位器箱 differential limit switch box 变幅绞车 luffing winch起货绞车 hoisting winch吊货滑车 falling block液压千斤顶 hydraulic cylinder安全工作负荷 safe working load/SWL吊货索 cargo fall千斤索 topping lift起货机 cargo winch千斤索绞车 topping lift winch吊杆 boom吊货钩 cargo hook起重柱 Samson post/SP双杆联合 union purchase舷内吊杆/大关 inside boom舷外吊杆/小关 outside boom调整稳索 adjustable guy保险稳索 insurance guy三角眼板 triangle eye-plate吊货索滑车组 cargo fall tackle千斤索滑车组 topping lift tackle稳索 guy导向滑车 leading block桅柱 mast重型吊杆 heavy derrick控制台 cross-tree轻型吊杆 derrick山字吊货钩 Flemish hook连接横杆 connecting traverse拉索 pull guy滚动式 rolling type滚翻式 rolling and tipping type 舱口围板支架 brackets偏心轮 eccentric wheel连接链 connecting chain上滚轮 upper roller压紧器 cleat halve上升轨 wheel ramp导装面板 leading panel折叠式 folding type铰链 slotted hinge固定钩 fixed hook存放臂 stowing arm钢索 wire pendant铰接滑车 hinged sheave拖拽眼板 hauling eye plate关闭臂 closing arm固定钩 securing hook熏舱 fumigation《货物系固手册》 cargo securing manual/CSM 货物单元 cargo unit标准货 standardized cargo半标准货 semi-standardized cargo非标准货 non-standardized cargo货物系固设备 cargo securing device系固 secure支持 support最大系固负荷 maximum securing load/MSL固定式系固设备 fixed securing device携式系固设备 portable securing device地铃 lashing eye系固链条 lashing chain紧链器 tension lever钢丝绳 lashing wire rope系固钢带 lashing steel band花篮螺丝/松紧螺旋扣 turnbuckle系固槽座 lashing pot绑扎带 lashing band象脚 elephant feet拖车支架 trailer trestle拖车千斤顶 trailer support jack轮楔 wheel chock系固钢丝 lashing wire快速释放紧索器 quick release lashing 底座 foundation 滑移底座 sliding foundation埋入式底座 imbed foundation燕尾槽/燕尾底座 dovetail foundation板式底座 doubling plate foundation插座 socket固定锥 welding cone可折地铃/D形环 D-ring眼板 lashing plate箱格导轨系统 cellguide system横撑材 transverse prop导箱构件 container guide member横向支撑底座 lateral support foundation集装箱绑扎桥 lashing bridge扭锁 twistlock操作杆 operating rod半自动扭锁 semi-automatic twistlock锁销 locking pin底座扭锁 bottom twistlock堆锥 stacking cone中间堆锥 inter-bridge stacking cone底座堆锥 bottom stacking cone可移动锥板 removable cone plate自动定位锥 automatic fixing cone锁紧装置 locking device调整堆锥/高度补偿锥 leveling stacking cone桥锁 bridge fitting绑扎杆/绑扎棒 lashing bar横向撑柱 lateral support element辅助工具 accessory appliance分舱因数 factor of subdivision重心 gravity/G稳心 metacenter/M船舶修理 ship repair计划修理 planned repair临时修理 occasional repair航修 voyage repair小修 current repair岁修 annual repair检修 overhaul船坞 dock坞修 dock repair事故修理 accident repair自修 self repair防腐锌板 ZINC protector/anticorrosion zinc plate 进坞图 docking plan舵结构图 rudder construction plan浮坞 floating dock船底望光 light measure with eye for the bottom deforming 裂缝 crack止裂孔 stopper hole船舶修理单 repair list缺陷清单 defect list外观检查 external examination内部检查 internal examination缺陷修补 imperfection mend系泊试验 docking test密性试验 watertight test冲水试验 hose testing压水试验 water test气密试验 gastight test舷梯 gangway航行与信号设备 navigation and signal equipment通信设备 communication equipment倾斜试验 inclining test航行试验 navigation test加强检验附加标志 ESP/Enhanced Survey Program水下检验 in-water survey压载水管理计划 BWMP/ballast water management plan入级检验 classification survey保持船级检验 survey for class maintenance 年度检验 annual survey中间检验 intermediate survey坞内检验 docking survey特别检验 special survey循环检验 continuous survey法定检验 statutory survey营运中检验 survey for ships in service定期检验 periodical survey换证检验 change certificate survey附加检验 additional survey。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Copyright ASCE 2004
Deepwater Mooring 2003
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Copyright ASCE 2004
Deepwater Mooring 2003
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Copyright ASCE 2004
Deepwater Mooring 2003
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Copyright ASCE 2004
Deepwater Mooring 2003
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Copyright ASCE 2004
Deepwater Mooring 2003
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Copyright ASCE 2004
Deepwater Mooring 2003
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Copyright ASCE 2004
Deepwater Mooring 2003
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Copyright ASCE 2004
Deepwater Mooring 2003
Hale Waihona Puke Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Copyright ASCE 2004
Deepwater Mooring 2003
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Copyright ASCE 2004
Deepwater Mooring 2003
Copyright ASCE 2004
Deepwater Mooring 2003
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.
Copyright ASCE 2004
Deepwater Mooring 2003
Deepwater Mooring Systems Downloaded from by Dalian University Of on 07/11/12. For personal use only. No other uses without permission. Copyright (c) 2012. American Society of Civil Engineers. All rights reserved.