工厂常用名词中英文对照
工厂内常用英文简称辞汇解释
工廠內常用英文簡稱辭彙解釋品質人員名稱類QC quality control 品質管理人員FQC final quality control 終點品質管制人員IPQC in process quality control 制程中的品質管制人員OQC output quality control 最終出貨品質管制人員IQC incoming quality control 進料品質管制人員TQC total quality control 全面質量管理POC passage quality control 段檢人員QA quality assurance 質量保證人員OQA output quality assurance 出貨質量保證人員QE quality engineering 品質工程人員SQE supplier quality engineer 供應商品質工程師品質保證類FAI first article inspection 新品首件檢查FAA first article assurance 首件確認TVR tool verification report 模具確認報告3B 3B (3 tooling booking items) 模具正式投產前確認(壓力、溫度/油,水、料)CP capability index 能力指數CPK capability index of process 模具製程能力參數SSQA standardized supplier quality 合格供應商品質評估OOBA out of box audit 開箱檢查QFD quality function deployment 品質機能展開FMEA failure model effectiveness analysis 失效模式分析8D 8 disciplines 8項回覆內容FA final audit 最後一次稽核CAR corrective action request 改正行動要求corrective action report 改正行動報告PDCA Plan, Do, Check, ActFTA Factor tree analysis 因素樹分析IS Initial Sample 首批樣品OTS Off tool samples 初期樣品PS Prototype sample 手工樣品FQC運作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小AC Accept 允收RE Reject 拒收CS Critical specification 重要特性MAJ Major 主要的MIN Minor 輕微的AOQ Average Output Quality 平均出廠品質AOQL Average Output Quality Level 平均出廠品質Q/R/S Quality/Reliability/Service 品質/可靠度服務MIL-STD Military-Standard 軍用標準S I-S IV Special I-Special IV 特殊抽樣水準等級P/N Part Number 料號L/N Lot Number 批號B/N Bacht Number 批號AWD Accept with Deviation 特采UAI Use As It 首件檢查報告FPIR First Piece Inspection Report 百萬分之一PPM Percent Per Million 批號制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制R Range 全距AR Average Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility & Repeatability 量具之再制性及重測性判斷量可靠與否DIM Dimension 尺寸DIA Diameter 直徑FREQ Frequency 頻率N Number 樣品數其他品質術語類QCC Quality Control Circle 品質圈QIT Quality Improvement Team 品質改善小組PDCA Plan Do Check Action 計劃執行檢查總結ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 目標方針TQM Total Quality Management 全面品質管理MRB Material Reject Bill 退貨單LQL Limiting Quality Level 最低品質水準RMA Return Material Audit 退料認可QAN Quality Ameliorate Notice 品質改善活動ADM Absolute Dimension Measurement 全尺寸測量QT Quality Target 品質目標7QCTools 7 Quality Controll Tools 品管七大手法通用之件類ECN Engineering Change Notes 工程變更通知(供應商) ECO Engineering Change Order 工程改動要求(客戶) PCN Process Change Notice 工序改動通知PMP Product Management Plan 生產管制計劃SIP Specification In Process 製程檢驗規格SOP Standard Operation Procedure 製造作業規範IS Inspection Specification 成品檢驗規範ABOM Bill Of Material 物料清單PS Package Specification 包裝規範SPEC Specification 規格DWG Drawing 圖面部類PMC Production & Material Control 生產和物料控制PPC Production Plan Control 生產計劃控制MC Material Control 物料控制ME Manufacture Engineering 製造工程部PE Project Engineering 產品工程部A/C Accountant Dept 會計部P/A Personal & Administration 人事行政部DC Document Center 資料中心QE Quality Engineering 品質工程(部)QA Quality Assurance 品質保證(處)QC Quality Control 品質管制(課)PD Product Department 生產部LAB Laboratory 實驗室IE Industrial Engineering 工業工程R&D Research & Design 設計開發部P Painting 烤漆(廠)A Assembly 組裝(廠)S Stamping 沖壓(廠)生產類PCS Pieces 個(根,塊等)PRS Pairs 雙(對等)CTN Carton 卡通箱PAL Pallet/skid 棧板PO Purchasing Order 采購訂單MO Manufacture Order 生產單D/C Date Code 生產日期碼ID/C Identification Code (供應商)識別碼SWR Special Work Request 特殊工作需求L/N Lot Number 批號P/N Part Number 料號其他OEM Original Equipment Manufacture 原設備製造PCE Personal Computer Enclosure 個人電腦外設PC Personal Computer 個人電腦CPU Central Processing Unit 中央處理器SECC SECC` 電解片SGCC SGCC 熱浸鍍鋅材料U.S.A the United States of America 美國A.S.A.P As Soon As Possible 盡可能快的E-MAIL Electrical-Mail 電子郵件N/A Not Applicable 不適用QTY Quantity 數量vs. versus 以及.REV Revision 版本JIT Just In Time 零庫存I/O Input/Output 輸入/輸出OK OK 好NG Not Good 不行,不合格C=0 Critical=0 極嚴重不允許ESD Electro Static Discharge 靜電排放5S 希臘語整理,整頓,清掃,清潔,教養ATIN Attention 知會CC Carbon Copy 副本復印相關人員APP Approve 核準,認可,承認CHK Check 確認AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只讀光碟FDD Floppy Disk Drive 軟碟機HDD Hard Disk Drive 碟碟機REF Reference 僅供參考CONN Connector 連接器CAV Cavity 模穴CAD Computer Aid Design 計算機輔助設計ASS''''Y Assembly 裝配,組裝MAT''''S Material 材料IC Integrated Circuit 集成電路T/P True Position 真位度TYP Type 類型WDR Weekly Delivery Requirement 周出貨需求C?T Cycle Time 制程週期L/T Lead Time 前置時間(生產前準備時間)S/T Standard Time 標準時間P/M Product Market 產品市場3C Computer, Communication, Consumer electronics’ 消費性電子5W2H When, Where, Who, What, Why, How,How many5M Man, Machine, Material, Method, Measurement4M1E Man, Machine, Material, Method, Environment4MIH Man, Material, Money, Method, Time 人力,物力,財務,技術,時間(資源)SQA Strategy Quality Assurance 策略品質保證DQA Design Quality Assurance 設計品質保證MQA Manufacture Quality Assurance 製造品質保證SSQA Sales and service Quality Assurance 銷售及服務品質保證LRR Lot Reject Rate 批退率BS Brain storming 腦力激蕩EMI Electronic Magnetron Inspect 高磁測試FMI Frequency Modulator Inspect 高頻測試B/M Board/Molding (flat cable)SPS Switching power supply 電源箱DT Desk Top 臥式(機箱)MT Mini-Tower 立式(機箱)LCD Liquid Crystal Display 液晶顯示器CAD Computer AID Design 電腦輔助設計CAM Computer AID Manufacturing 電腦輔助製造CAE Computer AID Engineering 電腦輔助工程BIOS Advanced Basic in put/output system 先進的基本輸入/輸出系統CMOS Complementary Metal Oxide Semiconductor 互補金屬氧化物半導體PDA Personal Digital Assistant 個人數位助理IC Integrated Circuit 集成電路ISA Industry Standard Architecture 工業標準體制結構MCA Micro Channel Architecture 微通道結構EISA Extended Industry Standard Architecture 擴充的工業標準結構SIMM Single in-line memory module 單項導通匯流組件DIMM Dual in-line Memory Module 雙項導通匯流組件LED Light-Emitting Diode 發光二級管FMEA Failure Mode Effectiveness 失效模式分析W/H Wire Harness 金屬線緒束集組件F/C Flat Cable 排線PCB Printed Circuit Board 印刷電路板CAR Correction Action Report 改善報告NG Not Good 不良WPR Weekly Delivery Requirement 周出貨要求PPM Parts Per Million 百萬分之一TPM Total Production Maintenance 全面生產保養MRP Material Requirement Planning 物料需計劃OC Operation System 作業系統TBA To Be Design 待定,定缺D/C Drawing Change 圖紙變更/設計變更EMI Electrical-Music Industry 電子音樂工業RFI Read Frequency Input 讀頻輸入。
工厂常用专业术语(硅胶、模具企业中英文对照表)
46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93
印刷字体斜 气泡 字体偏位 产品相混 颗粒 硫化剂 产品送错工序 键帽刮伤 不同型号的合格证相掺 资料单与产品型号不符 银粉粒 整批合格证错 漏印导电 键帽粘偏 切割图形不正 多挖KT 雾面PU 漏挖KT 粘面 挖错KT 多切KT 漏印字体 印错字体 切割方向错 漏喷消光 漏切割 漏喷PU 漏滴注 漏塞料 环绕 丝网 键 寿命 直径 电镀 剖面图 不良 参考 额外冲程 参考面 印刷置具 PU 不良 喷 粘胶 冲程 类型 修改 圆的
英语
flash;burr;galling pill overflow spots;dirty dots torn dirty mark；contaminant pill badness adhere to impurities short mold compounding NO. of pieces Material cutting silicone rubber PMS（Pantone） pin hole color overflow force defect gas mark gas bubble problem insensibility defect of KT black spot pill torn mould mark deform；distort ;deformation;distortiБайду номын сангаасn insert kt in reverse dented;recess;sink mark insert wrong kt protruding mark dimension oversize missing kt when inserting conductive pill jig post curing actuating force pressuring absence of locating hole double pill commixture of different mould not clear number mould eccentricity adhere to printing ink printing defect appearance defect electrical defect shift printing defect oil amass
工厂全名中英文对照
工厂全名中英文对照Chemical Factory 化工厂Petrochemical Plant 石油化工厂Oil Chemical Factory 油脂化工厂Chemical Fertilizer Plant 化肥厂Potassium Fertilizer Plant 碳肥厂Chemical Fibre Plant 化学纤维厂Synthetic Fibre Plant 合成纤维厂Soap Factory 肥皂厂Chemical Factory of Daily Use 日用化工厂Toothpaste Factory 牙膏厂cosmetic Factory 化妆品厂Perfumery Plant 香料厂Beauty Products Factory 美容品厂Paint Factory 油漆厂Cement Plant 水泥厂Building Materials Factory 建材厂Timber Mill 木材厂Furniture Factory 家具厂Bricks and Tiles Plant 砖瓦厂Lime Factory 石灰厂Power Plant 发电厂Water Works 自来水厂Electroplate Factory 电镀厂Elevator Factory 电梯厂Iron Works 钢铁厂Stainless Steel Plant 不锈钢厂Alloy Steel Plant 合金钢厂Metallurgical Refinery 冶炼厂Copper Material Factory 铜材厂Aluminum Material Factory 铅材厂Non-ferrous Metals Processing Factory 有色金属加工厂Casting Factory 铸造厂Boiler Factory 锅炉厂Metallurgical Factory 冶金厂Machines Plant 机器厂Heavy Machines Plant 重型机器厂Machine Tools Plant 机床厂Diesel Engines Factory 柴油机厂Compressors Factory 压缩机厂Electrical Machinery Factory 电机厂Coolers Factory 冷冻机厂Machinery Plant 机构制造厂Shipping Machinery Plant 船舶机械厂General Machinery Plant 通用机械厂Crane Factory 起重机厂Tractor Factory 拖拉机厂Farm Tools Plant 农具厂Machinery Plant of Light Industry 轻工机械厂Commercial Machinery Plant 商业机械厂Building Machinery Plant 建筑机械厂Engineering Machinery Plant 工程机械厂Washing Machinery Plant 洗涤机械厂Mining Machinery Plant 矿山机械厂Heavy Machinery Plant 重型机械厂Shipyard 造船厂Automobile Factory 汽车制造厂Passenger Automobile Factory 客车制造厂Automobile Repair Plant 汽车修理厂Automobile Service Factory 汽车修理厂Bicycle Plant 自行车厂Sewing Machine Factory 缝纫机厂Clock Factory 钟厂Watch Factory 表厂Electronic Watch Plant 电子表厂Textile Mill 纺织厂Cotton Mill 棉纺织厂Woolen Mill 毛纺厂Silk Mill 丝厂Embroidery Factory 刺绣厂Clothing Factory 服装厂Woolen Sweater Mill 羊毛衫厂Towel Factory 毛巾厂Mosquito Net Factory 蚊帐厂Sheet Factory 床单厂Bedclothes Factory 床上用品厂Shoes Factory 鞋厂Leather Shoes Factory 皮鞋厂Rubber Shoes Factory 胶鞋厂Plastic Shoes Factory 塑料鞋厂Boots Factory 制靴厂Socks Factory 袜厂Leather Factory 皮革厂Oil Refinery 食油厂Flour Mill 面粉厂Rice Products Mill 米制品厂Flour Products Mill 面制品厂Foodstuffs Factory 食品厂Bakery 面包厂Milk Products Plant 乳制品厂Canned Foodstuffs Factory 罐头厂Beverage Factory 饮料厂Alcohol Plant 酒精厂Beer Brewery 啤酒厂Winery 酿酒厂Sugar Refinery 制糖厂Confectionery 糖果厂Biscuits Factory 干厂Spice Factory 调味品厂Gourmet Powder Factory 味精厂Cigarettes Factory 卷烟厂Matches Factory 火柴厂Bean Products Factory 豆制品厂Pastries Factory 糕点厂Tea Processing Factory 茶厂Pharmaceutical Factory 制药厂Medical Apparatus Factory 医疗器械厂Medical Equipment Plant 医疗设备厂Sanitary Materials Factory 卫生材料厂Insecticide Factory 农药厂Veterinary Medicines Factory 兽药厂Chemical Pharmaceutical Factory 化学制药厂Valve Plant 阀门厂Bearing Factory 轴承厂Gear Factory 齿轮厂Standard Component Factory 标准件厂Tools Factory 工具厂Hardware Tools Factory 五金工具厂Gas Appliance Factory 煤气用具厂Kitchen Utensils Factory 厨具厂Hardware Factory 五金厂Hardware and Electric Appliance Factory 五金电器厂Metal Processing Factory 金属加工厂Metal Component Factory 金属构件厂Lighter Factory 打火机厂Nail Factory 制钉厂Drawing Pin Factory 图钉厂Zipper Factory 拉链厂Lock Factory 锁厂Battery Plant 电池厂Fashlight Plant 电筒厂Electric Bulbs Factory 电灯泡厂Glass Factory 玻璃厂Plastics Plant 塑料厂Rubber Plant 橡胶厂Navigation Apparatus Factory 航海仪器厂Optical Instrument Factory 光学仪器厂Electronic Instruments Plant 电子仪器厂Educational Instrument Factory 教学仪器厂Printing House 印刷厂Toy Factory 玩具厂Paper Mill 造纸厂Musical Instrument Factory 乐器厂Piano Factory 钢琴厂Stationery Factory 文具厂Ink Factory 墨水厂Fountain Pen Factory 金笔厂Pencil Factory 铅笔厂Camera Factory 照相机厂Ceramics Factory 陶瓷厂Literature and Art Development Company 文艺进展公司Cultural Expansion Company 文化开拓公司Cultural Service Firm 文化服务公司Performing Company 演出公司Film Company 电影公司Film Service Firm 电影服务公司Broadcasting and Television Industry Company 广播电视工业公司Acoustics Engineering Company 音响工程公司Record Company 唱片公司Photography Industry Company 照相工业公司Exhibition Agency 展览公司Advertising Agency 广告公司Arts and Crafts Industry Company 工艺美术工业公司Art Design Firm 美术设计公司Art Decoration Firm 美术装潢公司Packaging Decoration Firm 包装装潢公司Building Engineering Company 建筑工程公司Building Foundation Company 建筑基础公司Civil Engineering Company 土木工程公司Garden Construction Engineering Company 园林建筑工程公司Building Material Company 建筑材料公司Building Material Supply Company 建筑材料供应公司Building Material Trading Company 建材贸易公司Building Material Service Company 建筑材料服务公司New Building Material Company 新型建筑材料公司Real Estate Development Company 房地产开发公司Real Estate Agency 房产代理公司Industrial Equipment Installing Company 工业设备安装公司Installing Company of Chemical Industry 化工安装公司Electrical Installing Company 机电安装公司Building Decoration Company 建筑装修〔装饰〕公司Building Decoration Engineering Company 建筑装修〔装饰〕工程公司Commercial Company 商业公司Collective Commercial Company 集体商业公司Overseas Chinese Commodities Supply Company 华侨商品供应公司Daily-use Sundry Goods Company 日用杂品公司Foodstuffs Company 食品公司Materials Company 物资公司Beverage Industry Company 饮料工业公司Frozen Foodstuffs Company 冷冻食品公司Native Produce & Animal By-products Import and Export Corporation 土产畜产进出口公司Chemicals Import and Export Corporation 化工进出口公司Metals & Minerals Import and Export Corporation 五金矿产进出口公司Electronics Import and Export Corporation 电子技术进出口公司Electric Wire & Cable Export Corporation 电线电缆出口联营公司Publishing Industry Trading Corporation 出版对外贸易公司Packaging Import and Export Corporation 包装进出口公司Instruments Import and Export Corporation 仪器进出口公司Historical Relics Exhibition Corporation for Foreign Countries 对外文物展览公司Performing Arts Agency 对外演出公司Overseas Building Materials and Equipment Corporation 对外建筑材料设备公司Foreign Trade Storage Corporation 对外贸易仓储公司Foreign Trade Transportation Corporation 对外贸易运输公司Foreign Trade Consultation & Technical Service Corporation 对外贸易咨询与技术服务公司Exhibition Agency for Foreign Countries 对外展览公司Export Commodities Fair 出口商品交易会Machinery & Equipment Import and Export Corporation 机械设备进出口公司Complete Plant import and Export Corporation 成套设备进出口公司Communications Import and Export Service Corporation 交通进出口服务公司Machine-building International Corporation 机械对外经济技术合作公司Machinery Import and Export Corporation 机械进出口公司Corporation for International Cooperation in Agriculture, Livestock and Fishery 农牧渔业国际合作公司Import and Export Service Company for Farms and Land Reclamation 农垦进出口服务公司Import and Export Commodities Inspection Corporation 进出口商品检验公司Technical Import and Export Corporation 技术进出口公司Textiles Import and Export Corporation 纺织品进出口公司Import Corporation of Textile Machinery 纺织机械进出口公司Import Corporation of Technology of Textile Machinery 纺织机械技术进出口公司Metallurgical Import and Export Corporation 冶金进出口公司Forestry Import and Export Company 林业进出口公司Forestry Machinery Import and Export Company 林业机械进出口公司International Packaging Leasing Corporation Ltd. 国际包装租赁International Non-ferrous Metals Leasing Corporation Ltd. 国际有色金属租赁International Book Trading Corporation 国际图书贸易International Economic Consultants Incorporation 国际经济咨询公司International Marine Containers Ltd. 国际海运集装股份Light Industrial Products Import and Export Corporation 轻工业品进出口公司Publication Import and Export Corporation 图书进出口公司Tea and Native Produce Import and Export Corporation 茶叶土产进出口公司Animal Breeding Stock Import and Export Corporation 种畜进出口公司Bearing Joint Export Corporation 轴承出口联营公司Aero-technology Import and Export Corporation 航空技术进出口公司Tobacco Import and Export Corporation 烟草进出口公司Leasing Company Ltd. 租赁Railway Foreign Service Corporation 铁路对外服务公司Cereals, Oil and Foodstuffs Import and Export Corporation 粮油食品进出口公司Coal Import and Export Corporation 煤炭进出口公司Microforms Import and Export Corporation 缩型出版物进出口公司Precision Machinery Import and Export corporation 周密机械进出口公司Abrasives Export Corporation 磨料磨具进出口公司Scientific Instrument import and Export Corporation 科学仪器进出口公司Foreign Trade Corporation 对外贸易公司Aquatic Products Import and Export Corporation 水产进出口公司Ceramics Import and Export Corporation 陶瓷进出口公司International Cooperation Corporation of Economics and Technology 国际经济技术进出口公司Trading Company 贸易公司Comprehensive Trading Company 综合贸易公司Trade Development Company 贸易进展公司Overseas Economic Trading Company 海外经济贸易公司Investment Company 投资公司Trust Company 信托公司International Trust and Investment Company 国际信托投资公司Loan Investment Company 信贷投资公司Overseas Chinese Investment Company 华侨投资公司People's Insurance Agency 人民保险公司Labour Insurance Agency 劳动保险公司Life Insurance Agency 人寿保险公司Pacific Insurance Agency 太平洋保险公司Securities Agency 证券公司Stock Exchange 股票交易所Futures Exchange 期货交易所Commodities Futures Exchange 商品期货交易所Futures Brokerage Company Ltd. 期货经纪Cereals and Oil Futures Exchange 粮油期货交易所Posts and Telecommunications Apparatus Company 邮电器材公司Posts and Telecommunications Engineering Company 邮电工程公司Running-water Company 自来水公司Water and Electricity Construction Company 水电建设公司Power Industry Company 电力工业公司Electrical Installing Company 电力安装公司Air Line 航空公司Shipping Company 船舶公司Ocean Transportation Company 远洋运输公司Salvage Company 打捞公司Ocean Shipping Agency 外轮代理公司Ocean Shipping Tally Company 外轮理货公司Ship-building Company 造船公司Automobile Transportation Company 汽车运输公司Container Transportation Company 集装箱运输公司Storage and Transportation Company 储运公司Taxi Company 出租汽车公司Automobile Service Company 汽车修理公司Ocean Shipping Supply Company 外轮供应公司Fishing-boat Industry Company 渔船工业公司Automobile Parts Company 汽车配件公司Automation Engineering Company 自动化工程公司Microcomputer Company 微电脑公司Computer Company 运算机公司Computer Software Development Company 运算机软件开发公司Hardware Company 五金公司Household Electric Appliance Company 家用电器公司Refrigerator Industry Company 电冰箱工业公司Radio Apparatus Company 无线电器材公司Performing Instrument Company 演出器材公司Printing Apparatus Company 印刷器材公司Teaching Instrument Company 教学仪器公司。
工厂生产常用英文术语缩写
工厂生产常用英文术语缩写工厂生产常用英文术语缩写5S : 5S管理ABC : 作业制成本制度 (Activity-Based Costing)ABB : 实施作业制预算制度 (Activity-Based Budgeting)ABM : 作业制成本管理 (Activity-Base Management)APS : 先进规画与排程系统(Advanced Planning and Scheduling)ASP : 应用程序服务供货商（Application Service Provider）ATP : 可承诺量 (Available To Promise)AVL : 认可的供货商清单(Approved Vendor List)BOM : 物料清单 (Bill Of Material)BPR : 企业流程再造 (Business Process Reengineering)BSC : 平衡记分卡 (Balanced ScoreCard)BTF : 计划生产 (Build To Forecast)BTO : 订单生产 (Build To Order)CPM : 要径法 (Critical Path Method)CPM : 每一百万个使用者会有几次抱怨(Complaint per Million) CRM : 客户关系管理 (Customer Relationship Management)CRP : 产能需求规划 (Capacity Requirements Planning)CTO : 客制化生产 (Configuration To Order)DBR : 限制驱导式排程法 (Drum-Buffer-Rope)DMT : 成熟度验证(Design Maturing T esting)DVT : 设计验证(Design Verification Testing)DRP : 运销资源计划 (Distribution Resource Planning)DSS : 决策支持系统 (Decision Support System)EC : 设计变更／工程变更 (Engineer Change)EC : 电子商务 (Electronic Commerce)ECRN : 原件规格更改通知(Engineer Change Request Notice) EDI : 电子数据交换 (Electronic Data Interchange)EIS : 主管决策系统 (Executive Information System)EMC : 电磁相容(Electric Magnetic Capability)EOQ : 基本经济订购量 (Economic Order Quantity)ERP : 企业资源规划 (Enterprise Resource Planning)FAE : 应用工程师(Field Application Engineer)FCST : 预估(Forecast)FMS : 弹性制造系统 (Flexible Manufacture System)FQC : 成品质量管理 (Finish or Final Quality Control)IPQC: 制程质量管理 (In-Process Quality Control)IQC : 进料质量管理 (Incoming Quality Control)ISO : 国际标准组织(International Organization for Standardization)ISAR: 首批样品认可(Initial Sample Approval Request)JIT : 实时管理 (Just In Time)KM ：知识管理 (Knowledge Management)L4L : 逐批订购法 (Lot-for-Lot)LTC : 最小总成本法 (Least Total Cost)LUC : 最小单位成本 (Least Unit Cost)MES : 制造执行系统 (Manufacturing Execution System)MO : 制令(Manufacture Order)MPS : 主生产排程 (Master Production Schedule)MRO : 请修(购)单(Maintenance Repair Operation)MRP : 物料需求规划 (Material Requirement Planning)MRPII : 制造资源计划 (Manufacturing Resource Planning)NFCF : 更改预估量的通知Notice for Changing ForecastOEM : 委托代工 (Original Equipment Manufacture)ODM : 委托设计与制造 (Original Design & Manufacture)OLAP : 在线分析处理 (On-Line Analytical Processing)OLTP : 在线交易处理 (On-Line Transaction Processing)OPT : 最佳生产技术 (Optimized Production Technology) OQC : 出货质量管理 (Out-going Quality Control)PDCA : PDCA管理循环 (Plan-Do-Check-Action)PDM : 产品数据管理系统 (Product Data Management) PERT : 计划评核术 (Program Evaluation and Review Technique) PO : 订单(Purchase Order)POH : 预估在手量 (Product on Hand)PR : 采购申请Purchase RequestQA : 品质保证(Quality Assurance)QC : 质量管理(Quality Control)QCC : 品管圈 (Quality Control Circle)QE : 品质工程(Quality Engineering)RCCP : 粗略产能规划 (Rough Cut Capacity Planning)RMA : 退货验收Returned Material ApprovalROP : 再订购点 (Re-Order Point)SCM : 供应链管理 (Supply Chain Management)SFC : 现场控制 (Shop Floor Control)SIS : 策略信息系统 (Strategic Information System)SO : 订单(Sales Order)SOR : 特殊订单需求(Special Order Request)SPC : 统计制程管制 (Statistic Process Control)TOC : 限制理论 (Theory of Constraints)TPM : 全面生产管理Total Production ManagementTQC : 全面质量管理 (Total Quality Control)TQM : 全面品质管理 (Total Quality Management)WIP : 在制品 (Work In Process)。
工厂专业英语术语
工厂专业英语术语Assem bly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌O OBA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse m achine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet m etal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource depart m en t 人力资源部production depart ment生产部门planning depart m ent企划部QC Secti on品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic m achine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting m achine铆合机position职务president董事长general manager总经理special assistant m anager特助factory director厂长depart m ent director部长deputy m anager | =vice m anager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant m anager助理to m ove, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect m aterial接料to reverse m aterial 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load m aterial上料to unload m aterial卸料to return m aterial/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient m anufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良em bedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车com pound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部autom atic screwdriver电动启子thicknes s gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present m embers出席人员subject主题conclusion结论decision item s决议事项responsible depart m ent负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准depart ment部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete m aterial良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw m aterials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flam e cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die butto n圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopp er清角active plate活动板baffle plate挡块cover plate盖板m ale die公模fem ale die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizat ion去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜 D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer 备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting m achine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine 亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grai n细粒grit m aker抽粒机cushion缓冲magnalium镁铝合金m agnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tem po生产进度现状torque扭矩spline=t he multiple keys花键quenchi ng淬火tem pering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。
工厂常用中英文互译
部门名称中英互译人事部办公室：HR（Human Resource ）Office保安室：Safe guarding Room or Guard Room接待室：Reception Room会客室（洽谈室）：Chatting Room会议室：Meeting Room塑胶部办公室：Plastic Dept Office配料室：Ｍixing Room or Mixing Compartment碎料室：Milling Room or Milling Compartment装配部办公室：Assembly Department OfficeA拉： A Line综合办公室：General Office仓库：Warehouse or Storehouse财务室：Financial Room采购部：Purchasing Department工程部：Engineering Department成本部：Cost DepartmentPMC部：PMC Department生产部：Manufacture Department喷油部：Oil Spout Department办公区：Office Area生产区：Manufacturing Area移印室Pad Printing Room品质部: QualityQA实验室：QA Lab工模部：Tooling Department工模部办公室：Tooling Department Office工模部仓库：Tooling Department Warehouse省模室：Polishing Room火花机室：Discharge Machine Room工模室：Tooling RoomCNC室: CNC Room车床室：Lathe Room磨床：Grinder前台：Reception Desk总监室: Director Room总经理室：General Manager Room贵宾餐厅：VIP Eatery卫生间：Rest Room管理食堂：Management Eatery员工食堂：Staff Eatery技工食堂：Artificer Eatery厨房：Kitchen储存室：Storage Room7S是整理(sort)、整顿(Neatness)、清扫(sweep)、清洁(sanitary)、素养(sentiment)、节约(save)、安全(safety)总裁办President Office行政部Administrative Department财务部Financial Department营销部Sales Department营运部Operation Department。
工厂常用中英文对照
制程统计管制
1 Total Quality Assurance
全面质量保证
1 Underwriter's Laboratories
美国安全协会认证
1 Zero Defects
零缺点
1 Trouble - Shooting
检修
1 Review
审查
1 Audit
积核
1 Burn-In
烘烧
1 Quality Cost
质量保证
1 Quality Control
质量控制
1 Quality Vendor List
合格厂商名单
1 Quality Audit
质量监察
1 Return Material Authorized
核可退回
1 Standard Inspection Procedure
标准检验指导书
1 Statistical Prcess Control
技术应用部门
6 Marketing Require Specification 市场需求规格
6 Pilot Run
试做
6 Research& Dwvelopment
研究开发
6 Test Support Department
技术支援单位
6 Version
版本
6 Release
解除/出版
6 Project Plan
备忘录
5 Management Information System 资料管理系统
5 Mass Production
量产
5 Mass Production Schedule
主生产排程
5 Material Require Planning
最新制衣厂常用术语中英文
制衣厂常用术语中英文对照表一）部门术语及常用词A.裁床：Cutting room1 纸样制作原理及方法：The methods & principle of pattern making2 排唛架方法：The methods of marker making3 YPD的计算及工厂唛架利用率：YPD calculation & marker use rate4 拉布及割布方法，工票之使用方法及功用：Methods & function of spreading & cutting5 裁剪日产量：Daily quantity of cutting6 裁单：Cutting ReportB．板房：Sample room1 裤子，恤衫的车缝工序：Understand the procedures of sewing pants and shirt2 熟识各个工序的称谓：Understand the name of various procedures3 熟识各个线缝的名称及功能：Understand the name and function in various seams4 了解缝1件衫所需的辅料：understand sub-materials used in a shirt5 熟识样板制造单：Understand sample orderC．车缝车间1 熟识生产制造单：Understand the production order2 熟识整个生产线的工序安排：Understand the product line lay out3 各个工序的定价标准：Price standard of various process4 质量控制方法：Methods of quality control5 日产量：Daily product quantity6 常见的车缝设备：Work-aids sewing Machine & attachments7 常见的车缝疵点：Various types of sewing problemD.洗水厂Washing department1 洗水方法及不同的洗水特点：Washing type & various characteristic2 不同洗水的洗涤剂：Various chemical consumption for each type of garment wash3 如何控制洗水质量：Garment washing quality controlE．包装：Packing department1 包装工序的任务及要求：What propose with packing process2 包装方法：Types of packing：Stand-up packing：企装, Flat packing：扁装Semi stand packing: 铲装/半企装3 包装所需的辅料：What assembly will be used in packing4 包装机械设备：Packing equipment5 装箱方法：Methods of packing6 出货所需之文件：Shipping document7 如何控制包装质量：How to control packing quality二）制衣厂质量检查QC Quality control1．服装中-英名称衬衣Shirt/Blouse T-恤T-Shirt毛衣Sweat shirt 西装Suit裤子Pants 牛仔裤Jeans喇叭裤子Bell bottom jeans 裙子Skirt外套Coat 连帽T-恤Parka运动衫Sports jacket 连衣裙Dress圆台裙Circular 百褶裙Gather Skirt裤裙Flare Culottes Skirt 马甲Vest背心Tank top 燕尾领Wing collar2．衣服部位中-英文名称前幅Front 后幅Back上级领Collar 下级领Collar Band前筒Front Placket 钮子Button stay袋Pocket 担干Yoke袖Sleeve 袖侧Sleeve placket介英Cuff 裤头Waist Band耳仔Belt Loop 拉链贴Zipper catch拉链牌Zipper Fly 袋贴Pocket Facing前浪Front Rise 后浪Back Rise裤脚Leg Bottom 侧骨Side Seam袋口Pocket Mouth 袖叉Sleeve Slit机头Riser 明袋Patch Pocket唇袋Jetted Pocket 袋盖Pocket Flap插袋Cross Pocket 袋衬Bearer袋布Pocket Bag 袖口贴Sleeve Band兜帽Hood 夹圈Armhole钮门Button Hole 凤眼Eyelet Button Hole 捆条圆领Crew neck3．制衣工序名称Garment Product Procedure纸样Pattern 唛架Marker裁剪Cutting 绣花Embroidery样板Sample 车缝Sewing洗水Washing 成衣染Garment Dye整烫Ironing 包装Packing质量检查Quality Inspection 质量控制Quality Control石洗Stone Wash 化学洗Chemical Wash茶化洗Teast Wash 漂洗Bleach Wash钮Button 线Thread唛头/商标Label 挂卡Hang tag贴纸Sticker 朴Interlining胶袋Plastic/Poly bag 胶夹Plastic Clip拉链Zipper 橡根Elastic Band肩垫Shoulder Pad 衬纸Tissue Paper绅Drawstring 领蝴蝶Collar Butterflies领胶条Collar Stripe 纸箱（Paper）Carton（胶）针(Poly) Pins 检针济Sticker纸板Paper board 蝴蝶Butterfly纸/胶领条Paper/Plastic collar band 尺码贴纸Size sticker插竹Collar stay 条形码Jan code/bar code4．车缝工序Sewing process埋夹close side seam 车唛sew label间线子口hem stitch seam上间袖attach sleeve/topstitch sleeve 打枣Tacking 接线Joints三）、布的中-英文名称1.梭织布Woven牛津纺Oxford 府绸Poplin多臂提花Dobby斜纹Twill青年布Chambray 绒布Flannel条格布gingham 泡泡纱Seersucker灯芯绒Corduroy 卡其Drill哔叽Serge 华达呢Gabercord主身布Body fabric撞布Contrast fabric条格Check 斜纹Stripe净色Solid 支数warp count2.针织布Knit平纹布Jersey (Drop 1*1 Jersey/Lycry Jersey)珠地Pique (Twill Pique /Oxford pique /Athletic pique)双珠地Lacoste (Oxford Lacoste 牛津珠地)双面布Interlock (interlock pique /interlock jacquard 双面提花)毛圈布Terry ( twill French terry 法兰绒/Fleece 磨毛毛圈布)提花Jacquard (herringbone /bubble jacquard 泡泡提花布)罗纹Rib (mini waffle 十字罗纹/法式罗纹French rib)棉布Cotton fabric麻布Linen丝绸Silk毛Wool化学纤维Chemical fiber四）制单要求The requirement in production order生产制单production order 样板制造单Sample order款号Style Number 客户Customer数量quantity 尺码Size spec.交货期Delivery 装箱要求Carton Requirement 纸箱规格Carton Measurement 毛重Cross height净重Net height 说明Description目的地Final destination 颜色color五）、其它样板Sample 货前板Pre-Production sample 销售板Sales Sample 展览板Presentation sample 批准板Approval sample 会议板Meeting Sample测试板Test sample 船头办Pre-shipment Sample 六）布疵常见术语紧纱：Tight 断纱：Broken Yarn走纱：Misend / Mispick 抽纱：Yarn with Drawn针孔：Needle Holes 针路：Vertical Line横间：Horizontal Line 漏针：Dropped Stitch停机布痕：Stop Mark 幼纱：Yarn Thinning/Thin Yarn错花：Wrong Pattern or Wrong Structure飞花：Fly yarn 色差Shading染色Color fastness 粗纱Thick yarn色纱Color yarn织错纱Wrong pick end稀密路Filling bar 布纹弯曲不平Bowing皱摺Crease 粗粒Slub起毛Hairy 织入杂物Gout起球Balling-up七）车缝常见术语跳线：Skip Stitch 用错原料：Wrong Material缝线散口：Run off 用错缝线：Incorrect Thread错唛：Wrong Label 破洞：Holes突咀：Excess Extension 不对称：Mismatched车着唛头：Sandwich Label 歪唛：Off Center or Side left/right 尖位不尖：Pointed Area not Sharp 弯位不弯：Unsmooth Curve爆口：Open Seam 披苏：Loose Thread插竹歪：Crooked Collar Stay 领底松：Collar setting too Loose烂钮尖：Burst Collar Point 领尖不对条：Mismatched Collar Stripe 错领型：Wrong Collar Shape 刀剪领：Scissoring露上领线：Thread Visible Outside 下级走样：Poor Banding领咀长短不定：Wrong Lapel Length 领错底面：Overturn Collar起耳子：Lock stitches-loop 断线：Broken Stitches落坑：Run off Stitch 积线球：Lumps of Thread藏色线：Trapped Color Thread 驳线不齐：Untidy Joined Stitching缝线阔窄：Uneven Seam 线路不美：Untidy Stitching皱：Pocking 露牙：Grinning走鸡：Miss Design Feature 大眼皮：Uneven seam高底袋：High/low pocket 筒起波浪：Fullness on Center Placket 筒歪：Crooked Center Placket 担干谷：Fullness on Yoke前肩大小边：Crooked front Folding 欠返针：Miss Back tack唛头字母被盖：Hidden Wordings 子口反骨：Seam Overturn欠开骨：Without Press Open 裤咀歪：Distorted Waistband End 大细唇：Uneven Lips 叠唇：Overlapped Lips裂唇：Open Lips 露朴：Exposure Interlining领咀朴空：Empty Collar Point 反光：Under ply Visible Outside 突钮子：Extension of Right Fly Too Long长短领尖：Uneven Collar Point Length起角：Nose in Extension-Collar /Cuff上领黏边：Folded Edge on Collar Closing内领窝谷：Fullness on Inside Around Collar setting车唛不对折痕：not Following the Folded Mark of Label下级领高低：Crooked Collar Hi-Low/off Center Line布包朴过紧：Tightness of Interlining after Sewing领朴起泡：Bubbling/Delimitation Fused Collar扭：Twisted/Misaligned Underarm and Side Seam打褶Make dart八）中英文色泽名称对照表Amber 琥珀色Khaki 土黄色Amethyst 蓝紫色Leek Green 葱绿色Antique Bronze 古铜色Lilac 淡紫色Brown 棕色Lemon 柠檬色Blue 蓝色Magenta 品红色Burgundy 红紫色Mooney 紫红色Bordeaux 红酱色Copper Brown 棕红色Maroon 酱紫色Brilliant Green 艳绿色Navy Blue 藏青色Black 黑色Orange 橙色Canary 嫩黄色Olive 橄榄色Clay 土灰色Pink 桃红色Salmon Pink橙红色/浅橙色Crimson 梅红色Plum 梅红色Pea Green 豆绿色Carmine 胭脂色Peacock 孔雀蓝Corinth 紫酱色Rubies 酱色Claret 枣红色Dark Blue 深蓝色Malachite Green 孔雀绿Fawn 淡黄褐Royal Blue 品蓝色Flesh Color 肉色Ruby 红玉色Fast Blue 坚牢色Sorrel 红棕色Golden Yellow 金黄色Sky Blue 湖蓝色Golden Brown 黄棕色Scarlet 大红色Grass Green 草绿色Turquoise Blue 翠绿色Grey/Charcoal 灰色Tangerine 桔红色Honey 蜜黄色Violet 紫色Isabella 淡黄色White(off white) 白色(米白) Jade Green 翠绿色Yellow 黄色Mastic 乳白色Red 红色九）物料名词：MATERIAL ITEMAttention Card 注意卡Buckle 字扣，铁扣Back end sticker 外箱检针济贴纸Plastic Butterfly 胶蝴蝶，胶托Button Mould 钮模Boxes 内箱B. Support 胶托（FOR M&S）B. Support 胶托（FOR M&S）Button 钮Carton 外箱Inner Carton 内箱Division Pad 内插筒Shoulder Cotton Pad棉织带Carton Tag 箱贴纸Plastic Clips 胶夹PL. Collar Support 胶领圈Paper Collar Stripe 纸领条Collar Stay 插竹Drawstring 棉绳Elastic Band 细橡根Embroidery Patch 绣花章Cum Tape 平橡根Herringbone Tape 人字带Hook and Eye 安全枢（银色）Plastic Hangers 胶衣架Hang Tag 挂卡Interlining 朴Jocker Tag 挂卡（For Tommy）Lace 丝带，花边Box end Label 内盒贴纸(For M&S) Content Label 成份唛Leather Disc 皮牌Exterior Label 旗唛（For ANF）Flag Label 旗唛，皮士唛Luggage Pin 胶针Item Label 旗唛Zipper Pull 拉链头Main Label 主唛Neck Label 领唛Country Origin Labe l 产地唛Pocket/Placket Label袋唛／旗唛Label of Other 其它唛Size Label 西士唛Wash Care Label 洗水唛Yoke Label 担干唛Content/WC/SZ Lab el 成份／洗水／西士唛Metal Clip 叉字铁夹Magic Sticker 魔术贴Nylon Loop 尼龙捆条Nylon String 尼龙绳Small Poly bag 小胶袋Poly bag 胶袋Plastic Clip 胶夹Poly Envelope 胶袋（封口）Golden Field Pocket Fabric 高丰袋布Piece goods (Job costing) 工作用品Paper Belt （纸）腰带（装饰用）Pins 针Cowhide Pager 牛皮纸Plastic 胶针Paper Tag 纸牌Price Ticket (OCR) 价钱牌Ribbon 丝带Rectangle Clip 方型胶夹Rivet 铆钉Poly bag Sticker 胶袋贴纸Carton Sticker 外箱贴纸Sundries 杂物Safety Pins 扣针Shoulder Pad(Tape) 扁带Inner Box Sticker 内盒纸箱Hang tag Sticker 挂卡贴纸Plastic Shirt Band 胶领条Paper Shirt Band 纸领条Shirt Board 纸板Size Sticker 西士贴纸Sticker 贴纸Glee 胶Staple Wire 备用电线Silicon Wrappers 缎带Levis Tab 转移印花Tag Tin 胶针（用枪打）Tissue Paper 纸领条，衬纸Thread 线Twill Tape 斜纹带Waist Band 印字系带，纸腰带Waist Tag 腰牌Zipper 拉链Plastic Sticker 胶贴纸十）、车缝常用名词中英文对照Linking 缝合Folding 折Crease 折边Slacks side seam 边缝Lapped seam 叠缝Single lapped seam 单线叠缝Blind stitch felling 暗缝线Flat felled seam 折边缝线Back tuck 回针，往复针Double welt seam 双线针Bar tacking 加固针缝Bound seam 包缝Top stitch 边缘明线Pad stitch 衲缝Triple stitch 三针平车，三针直线缝Run stitch 平缝，缝合Run and Turn 回针缝合Run and Open 开口缝Blind over edging 下摆翻边缝Tucked seam 缝褶Dart sewing 省缝Double stitched seam 双线缝，双层缝合Twin needle stitch 针平缝Stitch and Run 头，反缝Wrapping button shank 绕扣线Straight buttonhole 平眼锁钮孔Piped seam 夹紧缝Single lapped seam at edge 单线打边缝Edge stitched seam 边缘缝Lapped seam 包缝Welt seam 咬口折边，折缝Feltings 双折边叠缝，对折缝Button holing 锁眼扣Button sewing 钉纽扣Rolled seam 包边缝Threefold seam 三折缝Fourfold seam 四折缝Fell seam 双折边缝EGMS 界面常用英文单词翻译一、Personal Information 人事资料Transaction 处理，办理Employee Master 雇员Employee No. 雇员编号Employee Name 姓名Rack No. 厂卡号Social Security No. 社会保险号Birth Certificate No. 出生证号Identity No. 身份证号Income Tax No. 纳税号Sex 性别Marital Status 婚姻状况Male 男Female 女No. of Children 子女数Date of Birth 出生日期Join Date 入厂日期Effective Join Date 生效日期Daily Deduction Entry 扣减输入First Contract Date 第一次签合同日Date Leave 离职日期Home Address 家庭住址Area 地区Phone No. 电话号码Search Detail 查找细则Education Grade 学历Cutting Ticket No. 制单Description 描述Update 更新二、Daily Deduction Entry 扣减输入Process 过程Transaction Date 工票日期Daily Allowance Entry 补贴输入Piece and time rate worker时工和件工PO 定单三、Daily Compensate Hour Entry （COM）补时工输入Supplementary增补，追加Overtime Code加班代号Cutting Ticket No. 制单号Daily production Ticket Adjustment Entry工票修改界面Employee Status Control雇员状况Quantity数量Alter Prod Line组别Compensate Hours Entry补时工输入Factory PO制单号Amount金额Price单价Payroll工帐四、Payroll information : 工资资料Factory Code工厂编号Section Code部门Production Line Code组别代码Operation Code（Op. Code）工序号Employee Type雇员类别Job Level工种级别Job Class工种Pay Type付款方式Cash现金支付Labor Type劳动力类型Direct直接体力劳动Indirect非直接体力劳动Remuneration Scheme工资类别Monthly rated月薪Option属性Staff职员Bank Branch Code支行代号Basic Pay Amount基本工资Daily Production Ticket Table Entry工票输入界面Daily Production Ticket By Factory PO Entry工票输入界面Piece rated件薪Time rated时薪Worker工人Bank Code银行代号Bank Account No银行帐户号Employee Status雇员状况五、Piece and Time Rate Worker :计时和计件工人Op. Code工序编号Process Type生产过程描述Cutting裁床Sewing车间Fusing 烫朴Washing洗水Iron 烫部Packing包装六、Daily Production Ticket Normal Entry ：工票输入界面Production Ticket Normal Detail 工票输入细则Production Ticket Normal Header工票输入表头Normal Quantity原数Adjust Quantity修改后的数Daily Production Ticket Supplementary Entry追补工票输入界面Daily Compensate Hours Entry补时工输入界面Daily Allowance Entry补贴输入界面Daily Deduction Entry扣减输入界面Employee Group Setting评分输入界面Group ID组别Ratio Value评分Total Hours总出勤时间Normal正常出勤时间OTx1.5平时加班时间OTx 2周六/日加班时间OTx3法定假日加班时间Factory Suspend Hours回工时间Absent 缺勤时间Leave Descrp. 请假描述Print 打印Report 汇总Data Entry Report 输入资料汇总Print Selection 打印区域Production Ticket (Normal ) Report 工票总结From Page No. 从第页To Page No. 到第页七、Monthly Pay Detail 月薪细则Bank Payment 银行支付Allowance Detail 补贴细则Salaries Detail 薪水细则Deduction Detail 扣减细则Over Time Payment 加班工资Compensation Detail 补时工细则八、Daily Production Ticket Inquire 工票查寻界面Factory PO 制单号Amount 金额Price 单价Query Result 查寻结果中国十大食用油品牌1.金龙鱼益海嘉里集团2.福临门中国粮油食品集团3.鲁花山东鲁花集团有限公司4.多力上海佳格食品葵花油5.盛洲厦门中盛粮油6.汇福三河汇福粮油集团有限公司7.海狮上海良友海狮油脂8.民康江苏民康油脂有限公司9.红蜻蜓重庆市油脂公司10.鹰唛中山市鹰唛食品玉米油十大品牌1.长寿花邹平三星油脂公司有限公司2.西王山东西王沙渥拉油脂有限公司3.金龙鱼益海嘉里集团4.福临门中国粮油食品集团5.融氏上海融氏企业有限公司6.海狮上海良友海狮油脂7.道道全湖南巴陵油脂有限公司8.鹰唛中山市鹰唛食品9.大满贯金光食品（宁波）有限公司10.优沃吉林正望油脂有限公司十大花生油品牌1.鲁花山东鲁花集团有限公司2.金龙鱼益海嘉里集团3.龙大龙大食品集团有限公司4.福临门中国粮油食品集团5.喜燕青岛天翔集团6.星河河南省星河油脂有限公司橄榄油十大品牌1.多力橄榄油上海佳格食品有限公司葵花油2.欧蕾lamasia 西班牙橄榄油3.品利-亿芭利西班牙橄榄油4.阿格力斯argolis 希腊橄榄油5.阿茜娅橄榄油青岛阿茜娅商贸有限公司进口6.欧利维兰意大利橄榄油7.鲁花橄榄油山东鲁花集团橄榄油8.田园乐-优尼雅希腊橄榄油9.金色橄榄油地中海橄榄油。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Item(項目)Abbreviation(英文縮寫)Detail(全文)Chinese(中文)
Engineering DivisionPEprocess Engineering制程工程
工程部Product Engineering產品工程TETesting Engineering測試工程
IEIndustrial Engineering工業工程
EEElectronic Engineering電子工程
MEMechanical Engineering 機構工程
MEManufacturing Engineering製造工程
DCCDocument Control Center資料控制中心
OPTOperation Project Management專案經營部
R/D DivisionR/DResearch Developing開發
開發部CECCoministry Engineering Center同部工程中心TMTechnology Market技術推銷
Quality DivisionQAQuality Assurance品質保證
品管部Quality Audit品質稽核QCQuality Control 品質控制
QEQuality Engineering 品質工程
IQCIncoming Quality ControlVQAVendor Quality AssuranceIPQCIn Process Quality Control制程同步控制
OQAOut-going Quality AssuranceOQCOut-going Quality ControlOOBOut Of Box品質依賴性測試
QREQuality Rely Evaluation設計品質評估
DQEDesign Quality Evaluation客退品分析
RMARetrieve Material Analysis顧客服務
TQMTotal Quality Mangement 全面質量管理
Production DivisionMFD Manufacturing Department製造部
生產部SMDSurface Mounting Device表面貼著零件SMTSurface Mounting Technology表面貼著技術
AIAuto Insertion自動插件
MIManual Insertion人工插件
PDProduction Division產品部
PCBAPCB Assembly基板運作
資材部PURPurchasing採購PMCProduction & Material Control生(產)物(料)管(理)
MDMaterial Department物控
PCProduction Control生管
Administer DivisionVPVice President副總經理
管理部MOPManager經理HRHuman Resource人力資源部
FINFinance財務
工廠常用名詞中英文對照進料檢驗出貨檢驗Item(項目)Abbreviation(英文縮寫)Detail(全文)Chinese(中文)
工廠常用名詞中英文對照
EDEquipment Department工務
GRGeneral總務
MISManagement Information System 資訊管理系統
New projectT/RTrial Run新機種P/RPilot RunC/RControl RUN試產(投)
DRDesign Release設計核準
Phase In導入
Phase Out導出
Lead Time處理周期
LPRLab Pilot Run開發試制
EPREngineering Pilot Run工程試制
PPRProduction Pilot Run生產試制
MPMass Production大量試產
MPRMass Production Release大量投產核準
Engineering ChangeECEngineering Change工程變更
工程變更ENEngineering Notice工程通訊ECREngineering Change Request工程變更申請
ECNEngineering Change Notice工程變更公告
TECNTemporary Engineering Change Notice工程臨時變更公告
ECOEngineering Change Order工程變更指令
MNManufature Notice制程變更通知
PCNProto-type Change Notice原始變更通知
DCNDesign Change Notice設計變更通知
CRBChange Review Notice變更總結會議
ProductLCDLiquid Crystal Display液晶顯示器產品FDFlat Display平面顯示器GSIIIGlobal Stytle III全球第三代
Jag飛梭
SPECSpecification規格
LEDLight Emitter Display光射极顯示器
softwareDDCData Display Channel數據顯示通道軟件EEPROMElectronic Erase Programmable ROM電子可擦拭可編程只讀存儲器ROMRead Only Memory只讀存儲器
RAMRead Randomly Memory隨機存儲器
CPUCentr Processor Unit 中央處理單元
OSDOn screem Display屏幕顯示菜單
safetyEMIElectromagnetic Interference電磁幹擾安規EMC Electromagnetic Compatibiloty電磁相容性ESDElectrical Static Discharge靜電釋放
Arcing高壓放電
試制Item(項目)Abbreviation(英文縮寫)Detail(全文)Chinese(中文)
工廠常用名詞中英文對照
DPMSDisplay Power Management Signal顯示電源管理信號
HI-POT耐壓測試
VESAVideo Electronic Standard Association視訊電子標準協會
VGAVideo Gaphic Adapter影像圖形調整器
performancesPower Saving 省電畫面Ringing振鈴Rotation旋轉
CGConvergence 收斂
Morie波紋
Spot Electronation開機打點
Linearity線性
Raster Regulation光柵變動率
Jitter (Noise)幹擾
BrightnessContrast對比
高度Unifronity均勻度Raster底視
Purity色純度
W/BWhite Balance白平衡
Geometric DistrotionPincushion針形
幾何失真Barrel桶形Trapezoid梯形
Parallelogram平行四邊形
Tilt傾斜度
S-curveS形
Bow左PIN右Barrel
OthersSYNCSychronization同步
其它Frequency頻率X-ray ProtectionX射線保護
Cut-off亮點消除
Burn-in老化
OthersRespons反應速度
其它Display Mode顯示模式Degaussion消磁
Yield Rate通過率
MTFModulation Transfer Function調整轉換功能
ERSExernal Reference Spec.外部規格
Vendor/SupplierIQCIncoming Quality Control廠商VQAVendor Quality AssuranceAQLAcceptable Quality Level允收水準
FactoryDMRDefective Material Report材料缺陷報告
廠內VMIVisual Mechanical Inspection外觀機構檢驗
進料檢驗