SELECTION instruction_foxboro 43AP
Veriflo Division 产品与相关配件安全指南说明书
1. GeNeRAl INstRuctIoNs1.1. scope: This safety guide is designed to cover general guide-lines on the installation, use, and maintenance of Veriflo Divisionvalve, pressure regulator, and flow control products and relatedaccessories (“products”).1.2. Fail-safe: Veriflo products can and do fail without warning formany reasons. Design all systems and equipment in a fail-safe mode, so that failure of Veriflo products will not endangerpersons or property.1.3. Relevant International standards:For a good guide to theapplication of a broad spectrum of pneumatic fluid powerdevices see: ISO 4414:1998, Pneumatic Fluid Power – GeneralRules relating to systems. See for ordering infor-mation.1.4. Distribution: Provide a copy of this safety guide to each personthat is responsible for selection, installation, or use of Verifloproducts. Do not select or use Veriflo products without thor-oughly reading and understanding this safety guide as well asthe specific Veriflo publications for the products considered orselected.1.5. user Responsibility:Due to the wide variety of operatingconditions and applications for Veriflo products, Parker andits distributors do not represent or warrant that any particularVeriflo product is suitable for any specific end use system. Thissafety guide does not analyze all technical parameters that mustbe considered in selecting a Veriflo product. The user, throughits own analysis and testing, is solely responsible for:• Making the final selection of the appropriate Veriflo product;• Assuring that all user’s performance, endurance, mainte-nance, safety, and warning requirements are met and thatthe application presents no health or safety hazards;• Complying with all existing warning labels and / or providingall appropriate health and safety warnings on the equipmenton which the Veriflo products are used; and• Assuring compliance with all applicable government andindustry standards.1.6. safety Devices:Safety devices should not be removed, ordefeated.1.7. Warning labels:Warning labels should not be removed,painted over or otherwise obscured.1.8. Additional questions:Call the appropriate Parker technicalservice department if you have any questions or require anyadditional information. See the Parker publication for the productbeing considered or used, or call 1-800-CPARKER, or go to, for telephone numbers of the appropriatetechnical service department and Veriflo catalogs and publica-tions.2. pRoDuct selectIoN INstRuctIoNs2.1. operating pressure: The user must assure that the pressuresapplied to the product will never exceed the maximum oper-ating pressure of the product, the maximum operating pressureof any options and accessories connected to the product, andthe maximum operating pressure of any other system compo-nent. Consult product labeling and Veriflo Division catalogs formaximum operating pressures. Additional operating pressure considerations:• Pressure regulators have an outlet operating pressure rangethat is less than the maximum operating inlet pressure. Neverexceed the maximum operating inlet pressure. Never exceedthe maximum operating outlet pressure.• Pressure gauges should be selected such that the pressureto be measured is no more than 75% of the full scale range ofthe gauge. For additional information refer to ASME standardB40.1, Pressure Gauges and Gauge Attachments. See www. for ordering information.• Products may be fitted with special connections and adaptorsto connect the product to a pressure cylinder. The maximumoperating pressure of the product, its options, and accessoriesmust equal or exceed the maximum pressure of the cylinder.For more information regarding the selection and safe useof pressure cylinders and cylinder connections, contact theCompressed Gas Association (CGA), 4221 Walney Road,Chantilly, VA, 20151, Phone: 703-788-2700, Fax: 703-961-1831, or visit the CGA web page at .2.2. temperature Rating: Never exceed the temperature ratings ofa product. Excessive heat or cold can shorten the life expec-tancy of a product, cause improper function, and product rupture. Consult Veriflo Division catalogs for maximum and minimum temperature ratings.2.3. leakage: Most products experience small amounts of leakage.Product leakage must be suitable for the application, environ-ment, and the process fluid. Good system design and product selection require consideration of both internal and external leakage. Leakage can create hazardous situations due to expo-sure to the process fluid, unintended chemical reactions, loss of system pressure, or unexpected transfer of fluids and pressures within the system. Consult Veriflo Division catalogs for product leakage rates.2.4. severe leakage: The user must address in their system designand product selection any hazards that may result from severe leakage due to product or system failure. Good system design requires consideration of the possibility of severe internal and external leakage and may require safety pressure relief devices and secondary fluid containment. Severe leakage can create hazardous situations due to exposure to the process fluid, unin-tended chemical reactions, loss of system pressure, or unex-pected transfer of fluids and pressures within the system.2.5. Flow Rate:The flow rate requirements of a system are animportant consideration when selecting a product. Products need to be able to provide adequate flow and pressure for the desired application.2.6. environment:Many environmental conditions can affectthe integrity and suitability of a product for a given applica-tion. Veriflo Division products are designed for use in general purpose industrial applications. If these products are to be used in unusual circumstances such as direct exposure to sunlight, weather, and/or corrosive or caustic environments, such use can shorten the useful life and lead to premature failure of a product.Parker Hannifin Corporation Veriflo Division250 Canal Boulevard Richmond, CA 94804-0034 phone 510 235 9590fax 510 232 7396/verifloSafety GuidePN: 25000194Revision: –Date: 09.01.07 Parker Hannifin CorporationVeriflo DivisionPartek Operations7075 East Southpoint RoadTucson, AZ 85706phone 520 574 2600fax 520 574 2700/partek2.7. Fluid compatibility: Veriflo products are constructed from avariety of materials. The user is solely responsible for selectingand assuring that the product and materials of construction arecompatible with the process fluid. The user must take extremecaution when selecting products and materials for use withcorrosive and hazardous fluids. The user should contact theirfluid supplier for additional safety and product selection guid-ance.2.8. oxygen service: Extreme caution must be taken when usingoxygen. A serious risk of ignition, fire, and explosion exists. Theuser is solely responsible for selecting the product and speci-fying materials to be used in oxygen service.• Do not use a product or operate a system if there is evidenceof contamination (e.g. debris, particles, oils, lubricants,grease, etc.);• Do not interchange products, components, or accessorieswith those that have been used in other types of gas service;• Do not operate a pressure regulator without a proper filter;• Always apply pressure to the regulator slowly to avoid heatingfrom adiabatic compression. Fast opening valves should notbe used.3. pRoDuct INstAllAtIoN AND opeRAtING INstRuctIoNs3.1. product Inspection: Prior to assembly or installation a carefulexamination of the product must be performed. All products mustbe checked for correct style, size, and model number. DO NOTuse any product that displays any signs of nonconformance.3.2. Installation and operating Instructions:Parker publishedInstallation and Operating Instructions must be followed. Theseinstructions are available by calling 1-800-CP ARKER, or at. Important installation and operating consider-ations:• Installation, operation, removal and servicing of these prod-ucts must be performed by knowledgeable personnel whounderstand how the products are to be applied and have beentrained and equipped for the handling, use and servicing ofpressurized fluids and systems.• The user must identify the product inlet and outlet ports bythe markings on the product to ensure proper connection tothe system. DO NOT use any product with unclear or missinginlet and outlet port markings.• After installation and servicing the product must be tested forproper function and leakage. Leak test methods should beappropriate for the system leak integrity requirements.• Do not use a product or operate a system if there is evidenceof contamination (e.g. debris, particles, oils, lubricants,grease, etc.).• Do not interchange products, components, and accessorieswith those that have been used in other types of gas service.• Process gases must be clean and free of moisture.• Do not operate a pressure regulator without a proper inletfilter.• Prior to installation, follow lockout and tagout procedures forthe system and equipment. Follow all government, state andlocal safety and servicing practices including, but not limited,to all OSHA Lockout Tagout procedures (OSHA Standard – 29CFR, Part 1910.147, Appendix A, The Control of HazardousEnergy – Lockout / Tagout).• Always wear appropriate personal protection equipment suchas approved safety glasses, face shield, apron, gloves, etc.4. mAINteNANce, RemoVAl, AND seRVIcING INstRuctIoNs4.1. maintenance:Even with proper selection and installation,product service life may be significantly reduced without acontinuing maintenance program. A maintenance program mustbe established and followed by the user and, at minimum, mustinclude instructions 4.2 through 4.6. Maintenance, inspection,service, and replacement intervals need to be established sothat products are replaced before any failure occurs. Importantconsiderations when establishing the frequency of mainte-nance, inspection, service, and replacement of Veriflo Divisionproducts:• Previous performance experiences including known failuresin the application or similar applications.• Government and/or industrial standards.• When failures could result in unacceptable down time, equip-ment damage or personal injury risk.4.2. Inspection: Any of the following conditions requires immediatesystem shut down and replacement of worn or damaged compo-nents. Never approach a product or system exhibiting these or other abnormal conditions until the system has been shut down and depressurized.• Escaping fluid and abnormal pressure readings: Escapingfluid and abnormal pressure readings may indicate severeleakage or product or system failure.• Damaged or degraded components: Look to see if there areany visible signs of wear or component degradation.• Kinked, crushed, or damaged hoses and plumbing: Kinkedplumbing can result in restricted fluid flow and lead to unpre-dictable system behavior.• Any observed improper system or component function: Imme-diately shut down the system and correct the malfunction.• Excessive dirt build-up: Dirt and clutter can mask potentiallyhazardous situations.4.3. Routine maintenance Issues:• Remove excessive dirt, grime and clutter from work areas.• Make sure all required guards and shields are in place.• Warnings and specifications on the product should not becovered or painted over. If masking is not possible, contactyour local representative for replacement labels.4.4. Removal: Before attempting to remove a product from service,review the product operating instructions. These instructions are available by calling 1-800-CPARKER, or by accessing the Parker WEB site at . Other important product removal considerations:• Installation, operation, removal and servicing of these prod-ucts must be performed by knowledgeable personnel whounderstand how the products are to be applied and have beentrained and equipped for the handling, use and servicing ofpressurized fluids and systems.• Follow lockout and tagout procedures for the system andequipment as stated in section 3.2 above.• Isolate the product from all pressure sources upstream anddownstream of the product by closing and locking out theappropriate valves.• Safely depressurize the product and system.• Properly purge hazardous fluids from the product andsystem.• Always wear appropriate personal protection equipment suchas approved safety glasses, face shield, apron, gloves, etc.4.5. servicing (conversion or replacing of any worn or damagedparts): Remove the product from the equipment or system prior to servicing. Follow guidelines above for removal instructions.Parker published Service Instructions must be followed. These instructions are available by calling 1-800-CPARKER, or at . To avoid unpredictable system behavior that can cause death, personal injury and property damage:• Installation, operation, removal and servicing of these prod-ucts must be performed by knowledgeable personnel whounderstand how the products are to be applied and have betrained and equipped for the handling, use and servicing ofpressurized fluids and systems.• After installation and servicing the product must be tested forproper function and leakage. Leak test methods should beappropriate for the system leak integrity requirements.• Warnings and specifications on the product should not becovered or painted over. If masking is not possible, contactyour local representative for replacement labels.4.6. putting serviced product back into operation:Follow theguidelines above for product installation and operating instruc-tions, section 3 above.Safety Guide 8/31/07© 2007 Parker Hannifin Corporation。
福克斯波罗系统FOXBORO
打开主机、CRT的电源，系统自检并启动， 等进入I/A初始环境
选择Config
系统维护
进入工程师环境，选择SoftMnt Shutdown_AW（或 Shutdown_WP） SHUTDOWN。 等到系统提示：Type Ctrl-d … for Maintainace 时， 键入系统密码：gnomes。 当出现<LETTERBUG>后，键入： <LETTERBUG> fsck –y ; fsck –y ; fsck -y 直到系统中再无错误提示为止，而后键入： <LETTERBUG> cd / <LETTERBUG> sync ; sync ; sync <LETTERBUG> init 0 待出现OK提示符为止，而后键入： <OK> power-off 关闭工作站电源。
I/A系统V7.1版本的安装
AW5101的安装过程
当工作站重启后等待约10分钟，以保证 INFOXMIX数据库安装完成，并用以下命 令进行确认： #ps –eaf|grep tbinit 注意：本步只对AW类型工作站需要， WP类型的工作站不要等待，可以立即进入 下一步工作
I/A系统V7.1版本的安装
AW5101的安装过程
待出现“#”提示符后，进行以下操作： # env /查看当前环境设置 # set STATION_TYPE=AW51 /将工作站类型设 置为AW51 # export STATION_TYPE /将站类型设置写入内存 # ia_install AW51 /执行I/A软件的安装 根据画面提示选择 “y” 在接下来的20分钟中，安装程序将自动将Solaris操作系 统及I/A的基本软件安装到AW5101硬盘中去。 待基本系统安装结束后，依照画面提示，键入命令： # reboot -- -r ”
GF-107系列缝纫机用户手册说明书
n .c z
- -5
w w w .g a r u d a
n .c z
- -9
w w w .g a r u d a
n .c z
68
69
3.
- -7
w
w
w
.g
a r u d a
n .c z
FEED BASE FEED DOG
1001006610012530SCREW
n .c z
- -22
w w w .g a r u d a
n .c z
- -23
w w w .g a r u d a
n .c z
- -24
w w w .g a r u d a
n .c z
- -25
w w w .g a r u d a
n .c z
- -26
w w w .g a r u d a
User Manual (maintenance)
GF-107 Series
ANITA B, s.r.o. Průmyslová 2453/7 680 01 Boskovice Czech Republic
tel: +420 516 454 774 +420 516 453 496
n .c z
11.
- -27
w w w .g a r u d a
n .c z
- -28
w w w .g a r u d a
n .c z
- -29
w w w .g a r u d a
n .c z
- -30
w w w .g a r u d a
n .c z
- -31
斯密比特· defend series 车顶扎牌架安装说明书
Part# DS2-4Parts Included Qty Parts Included Qty Clamp base (DS2) 4 ¼” Lock Washer 8 “L” Bracket (D8107A) 4 5/16” x ¾” Bolt 16 Hardware Pack (DS2-4-HP)5/16” Flat Washer 32 ¼” x ½” Phillips Screw 8 5/16” Lock Washer 16 ¼” Flat Washer 85/16” Nut 16Part# DS2-6Parts Included Qty Parts Included Qty Clamp base (DS2) 6 ¼” Lock Washer 12 “L” Bracket (D8107A) 6 5/16” x ¾” Bolt 24 Hardware Pack (DS2-6-HP)5/16” Flat Washer 48 ¼” x ½” Phillips Screw 12 5/16” Lock Washer 24 ¼” Flat Washer 125/16” Nut 24Part# DS2-8Parts Included Qty Parts Included Qty Clamp base (DS2) 8 ¼” Lock Washer 16 “L” Bracket (D8107A) 8 5/16” x ¾” Bolt 32 Hardware Pack (DS2-6-HP)5/16” Flat Washer 64 ¼” x ½” Phillips Screw 16 5/16” Lock Washer 32 ¼” Flat Washer 165/16” Nut 32Part# DS24-6Parts Included QtyParts Included Qty Clamp base (DS24) 6 ¼” Lock Washer 12 “L” Bracket (D8107A) 6 5/16” x ¾” Bolt 24 Hardware Pack (DS2-6-HP)5/16” Flat Washer 48 ¼” x ½” Phillips Screw 12 5/16” Lock Washer 24 ¼” Flat Washer 125/16” Nut 24Step 1:When necessary, remove the plastic end caps from one end of the factory roof rails. Remove any factory cross bars or racking.Step 2:Install the “L” bracket to the clamp base using the 5/16” x ¾” bolts with flat and\lock washers. Do not tighten at this time. Be sure the angle provides a flat mounting surface for the rackStep 3:Slide the appropriate number of clamp bases (matching the number of rack mounting locations) into each of the factory rails. Attach the bases to the rails using the ¼” x½” Phillips screws and ¼” large area washers. Do not tighten at this time.Step 4:Place roof rack in desired position on roof and slide the bases into position. Attachrack to bases with 5/16” x ¾” bolts, flat and lock washers. Check all attachments and rack location, tighten all hardware completely. Replace factory plastic end caps youpreviously removed. Installation is now complete.Notes:Defender Roof Racks are rated for loads of no more than 150lbs. evenly distributed.When carrying a spare tire, the tire should not exceed 33” diameterGrade 8 nut torque specificationsStandard Metric5/16” nuts 20 ft. lbs. M6 9 ft. lbs.3/8” nuts 35 ft. lbs. M8 23 ft. lbs.7/16”nuts 60 ft. lbs. M10 45 ft. lbs.1/2” nuts 90 ft. lbs. M12 75 ft. lbs.9/16” nuts 160 ft. lbs. M14 120 ft. lbs.5/8” nuts 175 ft. lbs. M16 165 ft. lbs.Limited WarrantiesSmittybilt’s products are covered under the following limited warranties only. Note that the duration of the limited warranty differs according to the material and finish of the product purchased. Subject to the duration and conditions of the limited warranty stated below, Smittybilt warrants to the original retail purchaser that its products are free from defects in material and workmanship. All other warranties and representations express or implied, are hereby disclaimed, including fitness for merchantability and buyer’s intended use or purpose. All parts are sold “AS IS” except for the limited warranties granted herein. Buyer assumes all risks as to the selection, suitability and performance of all goods and products selected. This limited warranty does not cover damage or impairment in any part due to misuse, improper installation, accident or contact with on-road or off-road hazards, product modification, improper or inadequate cleaning and/or maintenance. Smittybilt is not responsible for items damaged during shipping. This warranty is not transferable from the original buyer. For the original Buyer to be eligible for the limited warranty coverage, the Buyer must provide proof of purchase. Smittybilt strongly recommends returning the warranty registration card.Customer’s remedy hereunder shall be limited only to repair or replacement (at Smittybilt’s option) of any defective part(s) returned to Smittybilt at customer’s expense. The determination of whether or not a returned part is defective or subject to coverage under the limited warranties stated herein shall be made at Smittybilt’s sole discretion.To assure product quality, Smittybilt reserves the right to change product design, material, specification and finishes without prior notice to customers. This limited warranty gives you specific legal rights and you may also have other rights, which may vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply as to you. Also, some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. Smittybilt reserves the right to discontinue product lines and substitute products, or provide other remedies than those listed in this limited warranty for those discontinued products.WarningRollover and other types of vehicle accidents may result in serious injury or death to you, your passengers and others sharing the road. Smittybilt accessories are decorative and are not intended to reduce or avoid injury or damage in the event of an accident. The weight and location of Smittybilt accessories may affect your vehicles’ handling, stability and performance, creating an increased risk of accident or rollover. Before installing any accessory, check state laws and assure that the accessory will not obscure any lights or interfere with proper operation on your vehicle’s safety equipment. Consult your owner’s manual and the Smittybilt instructions, or additional safety information. Smittybilt products, nor the warnings contained herein, are not a substitute for your safe driving. Don’t drink and drive, always use seat belts and don’t drivefaster than conditions permit.。
Invensys Foxboro 43AP系列胶带指示控制器说明书
Product SpecificationsPSS 3-1B3 A43AP Pneumatic Indicating ControllersThese instruments indicate and control pressure, temperature, vacuum, and differential pressure. They provide process industries with a highly dependable and versatile group of instruments.WIDE SELECTION OF MEASURING ELEMENTS Invensys Foxboro offers the widest variety of element constructions and ranges in the industry. This versatility enables the 43AP Series Pneumatic Indicating Controllers to be applied to virtually any process.WIDE CHOICE OF CONTROL MODESOn-off, proportional, proportional plus derivative, proportional plus integral (reset), proportional plus integral plus derivative, differential gap, and automatic shutdown actions are available.BROAD RANGE OF INTEGRAL (RESET) AND DERIVATIVE ADJUSTMENTSThe integral unit has the complete range from 0.01to 50 minutes, and the derivative unit from 0.05 to 50 minutes.VARIETY OF OPTIONSThese controllers are available with an extensive list of optional features. Among these are internal bumpless automatic-manual transfer stations (two types), “batch” function, remote pneumatic set point, T ype 70 electric contacts, and control valve mounting.ACCURACY UNAFFECTED BY MOUNTING STRESSESBoth the control unit and the measurement element are mounted on a rigid steel plate. Thus, these components are isolated from case stresses due to mounting, and dependable accuracy is ensured.PSS 3-1B3 A Page 2POWER FAILURES DO NOT INFLUENCE PROCESS-DRIVEN INDICATIONA power failure and the likely subsequent loss of supply pressure do not influence the process-driven indication.WEATHERPROOF CONSTRUCTIONA glass fiber reinforced case and a gasketed door with a shatterproof polycarbonate window meet IEC IP53 and provide the environmental protection of NEMA® T ype 3.VERSATILE MOUNTINGInstruments may be mounted in a panel, on a flat surface, on a continuous vertical pipe, or on a vertical pipe stub.INTERNAL BUMPLESS AUTOMATIC-MANUAL TRANSFER STATIONThis option provides bumpless-balanceable transfer between automatic and manual control by simple 2-step procedure. Accidental transfer is avoided because the door must be opened to gain access to the transfer station.OPERATING CONDITIONSPERFORMANCE SPECIFICATIONS(Under Reference Operating Conditions unless otherwise specified)AccuracyINPUT TO POINTER±0.5% of span for qualified elements. INPUT TO OUTPUTDepends on measuring element used. Repeatability0.2% of span.Deadband0.1% of span.Ambient Temperature EffectMaximum control point shift at midspan per 55°C (100°F) change within normal operating conditions is 1% of input span.Supply Pressure EffectMaximum control point shift at midspan per 7 kPa (1psi) change within normal operating conditions is 0.2% of input span.Influence Reference OperatingConditionsNormal OperatingCondition Limits Operative LimitsAmbient T emperature24 ±2°C(75 ±3°F)–30 and +80°C(–20 and +180°F)–40 and +80°C(–40 and +180°F)Relative Humidity50% ± 10%No Limit No LimitSupply Pressure140 ± 1.4 kPa(20 ± 0.2 psi)115 and 155 kPa(17 and 23 psi)210 kPa(30 psi)PSS 3-1B3 APage 3 FUNCTIONAL SPECIFICATIONSElementsRefer to Measuring Element Specifications section for types, materials, and ranges.Controller ActionOutput signal either increases or decreases with increasing measurement, as specified; action is reversible in the field.Output Signal20 to 100 kPa, 3 to 15 psi, or 0.2 to 1.0 bar orkg/cm2, as specified.Air Consumption (Under normal operation)0.5 m3/h (0.3 cfm) at standard conditions.Output Gauge0 to 200 kPa, 0 to 30 psi, or 0 to 2 bar or kg/cm2, as specified.Set Point AdjustmentBy means of a knob mounted inside the case. PointersSet point and measurement pointers are fluorescent red.ScaleBlack markings on white background; sector-shaped with nominal effective length of 150 mm (6 in). (Refer to Chart and Dial Catalog 600 for available ranges.)Connections (Located in Bottom of Case.) PRESSURE AND VACUUM•For upper range-values up to 14 MPa (2000psi, or 140 bar or kg/cm2): Connections tapped forR1/4 or 1/4 NPT, as specified.•For upper range-values from 14 MPa (2000psi, or 140 bar or kg/cm[sup/2]) up to 70 MPa(10000psi, or 700 bar or kg/cm2): Connectionsthreaded for R1/2 or 1/2 NPT, as specified.•For upper range-values above 70 MPa(10000psi, or 700 bar or kg/cm2):9/16-18 Aminco® fitting used.PNEUMATICSupply and output connections tapped for 1/4NPT. MountingP ANELFlush in a panel up to 16 mm (0.6 in) thick. SURFACESuitable for all controllers having internally-mounted elements. Note that this mounting is not available with heavy duty helical elements. (These elements extend through the back of the case.) PIPEA kit of parts to fit a DN 50 or 2 in vertical pipe. YOKEKit of parts to fit a vertical DN 50 or 2 in pipe stub.This mounting scheme is designed specifically for controllers having rear-mounted differentialpressure elements.PHYSICAL SPECIFICATIONSEnclosureThe case is a glass fiber reinforced polyester molding, compounded for superior corrosion resistance. The door is glass fiber reinforced phenylene oxide, and has a shatterproof polycarbonate window, ultraviolet resistant. The overall construction is weatherproof, meets IECIP53, and provides the environmental protection of NEMA T ype 3.FinishCase, gray polyester; door, blue textured polyurethane.Data LabelAluminum data label fastened to inside of door with pressure sensitive adhesive. Includes space for Customer T ag data up to a maximum of 72 characters and spaces. For additional space, see optional Customer T ag.Approximate Mass4.8 kg (10.6 lb), excluding element.PSS 3-1B3 A Page 4MEASURING ELEMENT SPECIFICATIONS (T o achieve stated Performance Specifications)Differential Pressure Elements (Refer to PSS 3-4A2 A)Temperature Elements—Filled Thermal Systems (Refer to PSS 3-3A1 A)Pressure Elements (Refer to PSS 3-2A1 A)Element Code(a)ElementType Span Available Between(b)Maximum Operating Pressure kPa ∆P inH 2O ∆P mbar ∆MPa psi bar or kg/cm 2DE –A,BT ype 375 and 5020 and 20050 and 500142000140(a)Body and cover material for DE-A is zinc-cobalt; material for DE-B is 316 ss.(b)These are zero-based elements. The lower range value is zero and the upper range value is as shown (100% of span). Zerodifferential pressure can be elevated (compound range) so that lower range value is as low as -50% of span; or suppressed so that upper range value is as high as either –150% of span or 50 kPa (200 inH 2O) ∆P , whichever is less.Element Code SystemClass Range LimitsSpans Available Between °C °F °C°FT A –1A IA –130 and +315–200 and +60025 and 33040 and 600TA –2A and 2BIIA and IIB–45 and +315–50 and +600Varies with operating temperature(a)T A –3BIIIB–195 and +760–320 and +140070 and 550120 and 1000(a) Does not include temperature overrange values. Narrow spans are at low end of range. The maximum span is 215°C (400°F).Element Code Element Type Element Material Spans Available Between(a)kPa or MPa(b)psi(c)P A –CA(d)P A –CC(d)Absolute Bellows 316 ss Bronze 170 and 240 kPa abs 13 and 270 kPa abs 2.5 and 35 psia 1.9 and 39 psia PA –MA Absolute Double Spiral316 ss 140 and 700 kPa abs 20 and 100 psia PB –AA PB –AM(e)Helical316 ss K-Monel 1.4 and 40 MPa 1.7 and 14 MPa 200 and 6000 psi 200 and 2000 psi PB –BA PB –BM(e)Spiral 316 ss K-Monel 82 and 1400 kPa 140 and 1400 kPa 12 and 200 psi 20 and 200 psi PB –CA Bellows 316 ss 35 and 200 kPa 4.5 and 29 psi PB –CC BellowsBrass 34 and 100 kPa vac 30 and 180 kPa 4.9 and 15 psi 4 and 26 psi PB –DF Diaphragm 50 mm (2 in)Cu-Ni-Mn Alloy 6 and 35 kPa vac 6 and 70 kPa 0.9 and 5 psi 0.9 and 10 psi PB –PF Diaphragm 75 m (3 in)Cu-Ni-Mn Alloy 2 and 6 kPa vac 2 and 10 kPa 0.3 and 0.9 psi 0.3 and 1.5 psi PB –GA(f)Heavy-Duty Helical 316 ss 0.5 and 200 MPa 75 and 30 000 psi PC 3 to 15PC 3 to 18PC 3 to 27Receiver (Bellows)Brass20 to 100 kPa Range 20 to 120 kPa Range—3 to 15 psi Range 3 to 18 psi Range 3 to 27 psi Range(a)All elements except Code PC have zero-based ranges. Therefore, the lower range values are zero and the upper range valuesare as listed.(b)To convert kPa to bar or kg/cm 2, divide kPa value by 100. To convert MPa to bar or kg/cm 2, multiply MPa value by 10.(c)To convert psi to inH 2O, multiply psi value by 27.73. To convert psi to inHg, multiply psi value by 2.036.(d)Replacement element not calibrated.(e)K-Monel elements comply with NACE Standard MR-01-75.(f)Element extends through back of case. Replacement element not recommended. Return instrument to Invensys Foxboro.PSS 3-1B3 APage 5 MODEL CODEPSS 3-1B3 A Page 6OPTIONAL FEATURES(a)AS is Auxiliary Specification.Optional Feature DescriptionAS (a)Reference Bumpless Automatic-Manual TransferStation Consists of precision balance tube, regulator, and 2-position switch located within enclosure. A simple 2-step procedure provides bumpless transfer between automatic and manual control. A shutoff valve is supplied to allow automatic controller and relay to be serviced while retaining manual control.See Model CodeNozzle Seal Switch for Manual Control An internally mounted 2-position switch provides a simple andinexpensive method of achieving manual control. In the manual position, the switch seals the nozzle circuit and the output can be changed by varying the controller supply pressure with an external regulator.See Model CodeRemote Pneumatic SetPoint Integral Air Supply SetEnables the set point to be positioned from a remote source using a standard pneumatic signal. Available over the full span or part of the span.Fixed or adjustable combination pressure regulator and filter with 50mm (2 in) gauge mounted and piped to controllers. Fixed pressure regulator available without gauge. Maximum input 1 MPa, 150 psi, or 10 bar or kg/cm 2. NOTE: Not available with panel mounted controllers.See Model CodeIAST ype 70 Electric Alarm ContactsThis option comprises a rotor unit with up to 5 contacts. Relays are located in a separate external sheet metal housing. One relay may be supplied to energize on increasing or decreasing measurement, as specified. Or two relays may be provided, one energizing on increasing measurement and one on decreasing measurement. Relay contacts rating (noninductive load): 5 A at 120 V ac, 2 A at 240 V ac, and 5 A at 24V ac or dc. Electrical classification: ordinary locations.C –T/70Control Valve Mounting A 43AP Controller without elements extending from back of case may be assembled by Foxboro on a control valve fitted with a P50 or P110 Actuator.CVMExternal Connection to Integral Bellows Used when an external feedback signal must be applied to prevent integral circuit saturation.ECRBExternal Set Point A knob is fitted on door and engages set point adjustment mechanism.ESP High “Batch ”Modification For processes involving discontinuous control, the integral (reset) function is modified to prevent overshoot and to initiate immediate corrective action when control is resumed.BATCH-HGas Tight Case Special case machining and a gasketed 1/2 NPT vent connection permits operation of the controller with clean, noncorrosive process gas.GTC External Phenolic Nameplate Laminated plastic nameplate 38 X 76 mm (1.5 X 3 in) with whitecharacters on a black background. Maximum of 5 lines with 28characters or spaces 3 mm (0.13 in) high, or 24 characters or spaces 4 mm (0.16 in) high per line.N/PGlass Window inDoorShatterproof glass window used in areas where abrasive dust can cause scratching of standard polycarbonate window under frequent wiping conditions.GIDPSS 3-1B3 APage 7OPTIONAL FEATURES (Cont.)ORDERING INSTRUCTIONSOTHER M&I PRODUCTSOptional Feature DescriptionAS Ref.Stainless Steel Data Plate A stainless steel data plate 36 X 40 mm (1.4 X 1.6 in). Maximum of 4lines with 11 characters or spaces per line.SCT Customer TagStainless steel tag attached to instrument for customer tag data thatdoesn ’t fit on data plate. There can be a maximum of 10 lines of data with 40 characters per line.MTST amper-ProofKnob The door knob is removed to prevent unauthorized access to control adjustments. The door is opened with a specially shaped knob.TPK External Subpanel for Automatic-Manual SwitchingFor use only with controllers not having internal transfer switching. Consists of pressure regulator, nominal 40 mm (1.5 in) gauge, and 2-position transfer switch completely piped and assembled to external subpanel mounted to bottom surface of enclosure. Subpanel is finished in gray. The 1 in AS Code is for Control Codes A1, A2, A3, A7, and A8. The 2 in AS Code is for Control Codes A4 and A5. The S in AS Code is gauge in kPa, the E is psi, and the M is kg/cm 2.SD –1S SD –1E SD –1M SD –2D SD –2E SD –2M1. Model Number2. Mounting3. Element T ype, Material, and Range4. Measurement Range5. Measurement Connection6. Scale Range7. Supply Pressure and Output Signal 8. Controller Action 9. Optional Features 10. T ag and ApplicationInvensys Foxboro provides a broad range of measurement and instrument products, including solutions for pressure, flow, analytical, positioners, temperature, controlling and recording. For a listing of these offerings, visit the Invensys Foxboro web site at:/m&i.PSS 3-1B3 APage 8DIMENSIONS–NOMINAL33 Commercial Street Foxboro, MA 02035-2099 United States of America Inside U.S.: 1-866-746-6477 Outside U.S.: 1-508-549-2424 or contact your local Foxboro representative.Facsimile: 1-508-549-4999Invensys and Foxboro are trademarks of Invensys plc, its subsidiaries, and affiliates.All other brand names may be trademarks of their respective owners.Copyright 1977-2003 Invensys Systems, Inc.All rights reservedMB 010Printed in U.S.A.0403。
浩瀚电器重型电锅替换零部件手册说明书
VTMB22VB2S VB21VTMB2VB SERIES1 THRU45 - 678 - 9101112 - 13 - 14ELECTRICAL COMPONENTSVB SERIESELECTRICAL COMPONENTSILLUS.PART OF PART AMT.1417934-G1Block Assy. - Porcelain (208-240 V. Machine)(Incls.items 2, 3 & 4)..........................................AR 2SC-117-3Mach. Screw 10-24 x 11⁄4 Rd. Hd................................................................................................AR 3WS-23-20Washer.......................................................................................................................................AR 4NS-44-9Nut Assy 10-24 Hex “KEPS”......................................................................................................AR 5411497-B1Contactor (208-240 V. Machines)..............................................................................................AR 6417856-1Ground Lug (VB21, VB221) (1)7406708-G1Door - Breaker Panel (1)8412578-1Closure - Breaker (208-240 V.)(Shown) (1)9412578-2Closure - Breaker (480 V.) (1)10411501-14Circuit Breaker (50 Amp.)(208-240 V. Machines)......................................................................AR 11412577-1Box - Breaker. (1)12410472-9Block - Terminal (208/240 V.) (1)13410472-11Terminal Block (208-240 V.) (1)14410472-8Terminal Block (480 V.) (1)VB SERIESVB SERIES 5VB SERIESDOOR MECHANISM — OVENPL-40408-11011 THRU141516171821 - 2219 - 20VB SERIESDOOR MECHANISM - OVENILLUS.PART OF PART AMT.1410110-1Anchor - Spring (1)2417865-1Turnbuckle (36") (1)3405618-1Hook - Oven Door (1)4SC-90-1Bolt - Shoulder 1⁄2-13 x 2 Hex Hd (1)5408895-G1Crank Support Assy (1)6409240-2Spacer - 3⁄4 Pipe x 7⁄16 Lg (1)7404629-1Bearing - Hinge Pin (1)8408896-1Support - Crank (2)9410111-1Crank - Bell (1)10406363-1Spring - Door (Long) (1)11408895-G1Crank Support Assy (1)12409240-1Spacer - 3⁄4 x 5⁄16 Lg (1)13404629-1Bearing - Hinge Pin (1)14408896-1Support - Crank (1)15410090-G1Radius Bar Assy (1)16410089-1Arm - Door Control (1)17SC-90-1Bolt - Shoulder 1⁄2-13 x 2 Hex Hd (1)18PC-3-36Cotter Pin 3⁄32 x 1 Lg (1)19417860-1Bolt - Shoulder 3⁄8-16 x 3⁄4 Hex Hd (1)20417862-1Pin - Door Hinge (1)21410114-1Cover - Bottom Terminal (1)22410113-1Cover - Terminals (Top Oven Heat Elements) (1)412887-G1Door Frame Assy (1)VB SERIESBROILER GRID & DRIP SHIELDNAME OF PARTGrid Assy (1)Handle (1)Retainer - Drip Shield (1)Mach. Screw 10-24 x 1 Truss Hd (2)Spacer (2)Lock Nut 10-24 Light Flexloc (2)Post - Door (R.H.) (1)Post - Door (L.H.) (1)Drip Shield (1)Ball Bearing (Grid Carriage).........................................................................................................VB SERIESPL-40410-1915 - 16 CARRIAGE & LIFT UNIT (BROILER)PART OF PART406966-G1Carriage & Lift Mechanism (Incls.items 2 thru 7)......................................................................... 417866Spring - Carriage.. (1)405655-1Ball Bearing (Grid Carriage)......................................................................................................... 407488-1Pin - Bearing (2)417869-1Spacer (2)WS-3-3Washer (4)PC-3-36Cotter Pin 3⁄32 x 1 Lg (2)407619-1Ratchet Stop (1)406046-1Sleeve - Handle (1)414819-1Red Plastic Ball Handle................................................................................................................ 406056-2Adapter - Ball Handle. (1)407636-G1Push Rod Assy (1)417810-2Spring - Compression (1)NS-13-22Full Nut 3⁄8-16 Hex (2)406990-G1Grease Collector (1)407006-1Handle - Grease Collector (1)VB SERIESPL-40411-1ELECTRIC HEAT ELEMENTS(BROILER)PARTNAME OF PART407012-4Electric Heat Element 208 V........................................................................................................407012-5Electric Heat Element 240 V........................................................................................................407012-6Electric Heat Element 480 V........................................................................................................410465-1Retainer - Heating Element (3)407930-G1Heat Shield Assy (1)VB SERIES9 THRU141715 - 16PL-40412-1ELECTRIC HEAT ELEMENTS (OVEN)NAME OF PARTFrame Assy. - Top Elements (1)Frame Assy. - Bottom Elements................................................................................................... Element Assy. - Outer Top (208 V.)............................................................................................. Element Assy. - Outer Top (240 V.)............................................................................................. Element Assy. - Outer Top (480 V.)............................................................................................. Element - Outer Bottom (208 V.).. (1)Element - Outer Bottom (240 V.) (1)Element - Outer Bottom (480 V.) (1)VB SERIES2PL-40413-1MISCELLANEOUSNAME OF PARTFlue Riser (1)Strap - Back Attaching................................................................................................................Leg (SST) (4)Caster W/O Brake (2)Caster W/Brake (2)。
Omega TAC-386 多功能热敏电压转换器说明书
K-19ߜLinearized andCompensated to 1 mV/°C or °Fߜ±4°C (7°F) Accuracy ߜLow PowerConsumptionߜAccepts Miniature andSubminiature ConnectorsߜIntegral Cold-JunctionCompensationSpecificationsRanges:J:-105 to 750°C (-157 to 1382°F)K:-20 to 1200°C (-40 to 2192°F)T:-86 to 350°C (-123 to 662°F)Power:9 V alkaline battery (Model number MN1604)Accuracy: ±4°C (7°F)over entire rangeResponse Time:2 to 3 seconds Reference Junction Stability:0.05°C/°CInput Connection:Miniaturethermocouple connector type, SMP Output Connection:Standard banana jack,19 mm (3⁄4") spacing Operating Temp:0 to 50°C (32 to 122°F)Storage Temp:0 to 65°C (32 to 149°F)Dimensions:63.5 W x 76.2 D x 50.8 mm H (21⁄2x 3 x 2")An OMEGA WHITE BOX ®PRODUCTThe OMEGA ®TAC-386 can turn any chart recorder or voltmeter into an accurate temperaturemeasuring instrument. This universal thermocouple amplifier and linearizer provides a precision 1 mV/°C or °F for J, K, or T thermocouples. Cold-junction compensation is standard.TAC-386$162Battery IncludedThermocouple-to-Analog ConvertersContinuous AnalogOutVoltage OMEGACARE SM extended warranty program is available for models shown on this page.Ask your sales representative for full details when placing an order. OMEGACARE SMcovers parts, labor and equivalent loaners.manual and beaded wire thermocouple with subminiature connector. See Section A for additional matching thermocouple probes.Ordering Example: TAC-386-TC,thermocouple-to-analog converter in °C, Type T, $162.OCW-3OMEGACARE SM extends standard 1-year warranty to a total of 4 years ($41), $162 + 41 = $203.sSignal InC o n ve r t a n yM i l l i v o l tR e c o r d e ro r M e t e r to R e a dT e m p e r a t u r e !CANADA www.omega.ca Laval(Quebec) 1-800-TC-OMEGA UNITED KINGDOM www. Manchester, England0800-488-488GERMANY www.omega.deDeckenpfronn, Germany************FRANCE www.omega.frGuyancourt, France088-466-342BENELUX www.omega.nl Amstelveen, NL 0800-099-33-44UNITED STATES 1-800-TC-OMEGA Stamford, CT.CZECH REPUBLIC www.omegaeng.cz Karviná, Czech Republic596-311-899TemperatureCalibrators, Connectors, General Test and MeasurementInstruments, Glass Bulb Thermometers, Handheld Instruments for Temperature Measurement, Ice Point References,Indicating Labels, Crayons, Cements and Lacquers, Infrared Temperature Measurement Instruments, Recorders Relative Humidity Measurement Instruments, RTD Probes, Elements and Assemblies, Temperature & Process Meters, Timers and Counters, Temperature and Process Controllers and Power Switching Devices, Thermistor Elements, Probes andAssemblies,Thermocouples Thermowells and Head and Well Assemblies, Transmitters, WirePressure, Strain and ForceDisplacement Transducers, Dynamic Measurement Force Sensors, Instrumentation for Pressure and Strain Measurements, Load Cells, Pressure Gauges, PressureReference Section, Pressure Switches, Pressure Transducers, Proximity Transducers, Regulators,Strain Gages, Torque Transducers, ValvespH and ConductivityConductivity Instrumentation, Dissolved OxygenInstrumentation, Environmental Instrumentation, pH Electrodes and Instruments, Water and Soil Analysis InstrumentationHeatersBand Heaters, Cartridge Heaters, Circulation Heaters, Comfort Heaters, Controllers, Meters and SwitchingDevices, Flexible Heaters, General Test and Measurement Instruments, Heater Hook-up Wire, Heating Cable Systems, Immersion Heaters, Process Air and Duct, Heaters, Radiant Heaters, Strip Heaters, Tubular HeatersFlow and LevelAir Velocity Indicators, Doppler Flowmeters, LevelMeasurement, Magnetic Flowmeters, Mass Flowmeters,Pitot Tubes, Pumps, Rotameters, Turbine and Paddle Wheel Flowmeters, Ultrasonic Flowmeters, Valves, Variable Area Flowmeters, Vortex Shedding FlowmetersData AcquisitionAuto-Dialers and Alarm Monitoring Systems, Communication Products and Converters, Data Acquisition and Analysis Software, Data LoggersPlug-in Cards, Signal Conditioners, USB, RS232, RS485 and Parallel Port Data Acquisition Systems, Wireless Transmitters and Receivers。
FOXBORO 871PH-1P1A-3技术说明书
Output Overrange and Underrange Coated Reference Electrode Aging Glass and Broken Glass Electrode Calibration Required Liquid Leakage into Sensor Body Failed Preamplifier ATC Short and ATC Open
SENSOR AND TRANSMITTER DIAGNOSTICS
These functions include View Faults, Check Sensor, Resume Faults, and View History; and include:
Measurement, Compensation, and Analog e sensor input (pH, ORP, or ISE), or Galvanically isolated output. Approved/Certified as intrinsically safe device for
The user can enable or disable any of the listed faults. Fault status is displayed in the main Diagnostic Menu. If there are no faults, then “No Active Faults” will be displayed. The user can suspend faults from the measurement status for one hour, and can resume faults at any time.