5kw变频电源-使用说明书
单进单出-5KW 10KW变频电源接线方法,20KW 30KW变频电源面板操作方法

单进单出-5KW/10KW变频电源接线方法,20KW/30KW变频电源面板操作方法
单进单出接线方法如图
1、INPUT输入开关,OUTPUT输出开关
2、INPUT相对应的字母LN输入,接市电输入220V
3、OUTPUT相对应的字母LN输出,接需要供电的设备
显示面板操作方法
如图所示Hz(显示输出频率),V(显示输出电压),A(显示输出电流,所带的输出电流值),W(显示输出功率,所带的输出设备功率)
1、绿色长方形为开机启动键(打开输入开关,过30秒再按启动键)
2、红色长方形为复位键(1.比如关机时,可按此键后在关输入开关和输出开关。
2.使用中出现报警可按红色长方形再按绿色长方形可以正常工作)
3、拔式按键为可调输出频率,所显示在面板上面的Hz位置。
4、红色正方形加盖为高低档,高档时灯亮(0-300V),低档时灯不亮(0-150V)。
5、数字旋钮调输出电压,所显示在面板上面的V位置。
变频电源详细使用介绍

设备基本说明4.1.1.电源:●将380V的三根火线直接与调频电源的“输入”连接。
4.1.2.操作面板说明:图1●电源开关:负责变频电源部分的电源供给。
●高压指示:变频电源启动指示,。
●复位:负载失谐、变频源过热以及其它保护动作后的故障复位。
●急停:发生紧急情况的应急中断按键。
●分压器信号:用于接入分压器低压臂,最大电压100V,输入阻抗10M。
●接地:用于系统安全接地。
●USB接口:用于接入U盘查询资料或接入鼠标代替触摸操作.●液晶显示器:用于系统各参数、波形、菜单等的显示。
●输入:电源接入,三相 380V±5% 或单相220V±5% 45~65Hz,当电源为380V时,接A,B,C三相,可做额定负载试验;当电源为220V时,接A,C二相,只可做1/2负载试验。
●输出:变频电源输出至激励变压器输入。
4.1.3.接通电源变频电源操作箱在上电后合上“电源开关”,液晶屏点亮显示。
注意:仪器两侧开孔处的风扇在运行则表示表示仪器内部功率器件正常工作。
否则表示仪器内部过热或上次试验时没有复位。
此时应该切断电源,将仪器置于通风处静置1小时左右,待内部适当降低温度后再启动电源。
当风扇经常性的不启动时,建议立即与厂家联系。
当设备出现不可恢复性故障时,请不要自行拆卸仪器。
4.2.0. 触摸屏显示器:变频电源的控制屏幕为全触摸屏,你只需要在屏幕上要操作的位置轻轻点击,即可以进行操作。
4.2.1.开机后,显示界面如图2所示。
图24.2.2.试验参数配置:在每次试验前必须正确设置当次试验的各种参数!点击“参数配置”后,显示界面如图3所示。
图3●起始频率:选择自动调谐时的启动频率,下限频率最高为20Hz,上限频率最低为200Hz。
●终止频率:选择自动调谐时的结尾频率,下限频率最高为100Hz,上限频率最低为300Hz。
1.设置"起始频率"不可高于"终止频率"。
2.当第一次试验时建议采用30Hz~300Hz进行扫描。
5000A交流变频电源系列操作说明书

APS5000A系列交流变频电源使用说明书版本:01目录第一章安全规定 (5)1.1安全须知 (5)1.2维护和保养 (5)第二章安装要点 (6)2.1拆封和检查 (6)2.2使用前的准备 (6)2.3储存和运输 (7)第三章技术规格 (8)第四章操作面板介绍 (9)4.1前面板说明 (9)4.2后面板说明 (10)第五章操作说明 (11)第六章附录资料 (14)6.1故障检修 (14)6.2串行口通讯失败的检查 (14)6.3产品维护 (14)6.4R S232通讯说明 (15)第一章安全规定使用前应该注意的规定和事项!!!安全标志高电压警告符号。
高压危险符号。
机体接地符号。
接地符号1.1 安全须知·使用本交流变频电源前,请先完整阅读本操作说明,并充分了解本机所使用的安全标志,以策安全.·在开启本机的输入电源开关前,请先选择正确的输入电压规格.为防止意外伤害或死亡发生,必须由专业人员连接各输入或输出线,在搬移和使用机器时,请务必先观察清楚,然后再进行操作.1.2 维护和保养使用者的维护为了防止触电的发生,请不要掀开仪器的盖子。
本仪器内部所有的零件绝对不需使用者维护。
如果仪器有异常情况发生,请寻求我公司或其指定的经销商给予维护。
所附的线路和方块图只供参考之用。
定期维护交流电源供应器、输入电源线各相关附件等每年至少要仔细检验和校验一次,以保护使用者的安全和仪器的精确性。
使用者的修改用者不得自行更改机器的线路或零件,如被更改,机器保质期则自动失效并且我公司不负责任。
使用未经本公司认可的零件或附件也不给予保证。
如发现送回检修的机器被更改,我公司会将机器的电路或零件修复回原来设计的状态,并收取修护费用。
第二章 安装要点产品的拆封、检查、使用前的准备、和储存等的规则。
2.1 拆封和检查1. 打开交流变频电源的包装,请检查随机附件,附件:1.说明书一本.2.合格证一份。
3.电源线一条。
2. 本产品包装在一个用珍珠棉保护的包装箱内,客户如果收到包装箱有破损时,请检查机器的外观是否有无变形、刮伤、或面板损坏等。
5KVA变频电源

规则采样法
Tc D A O B
ur
tA
tD
tB
t
'
O
'
t
规则采样法的计算 规则采样法计算公式推导过程如下。在正弦调制信号波公式中,a称为调制度, ; 为信号波角频率。因此可得:源自ur a sin r t
三角波的一周期内,脉冲两边的间隙宽度为:
1 asinr t D 2 /2 Tc / 2
逆变桥输出V 和经滤波后输出 V
i
o
Vo
E
0
t2
Ts
最大脉动电流在实际中影响滤波电感设计,在脉动电流特别大的情况下,电感设计要 有讲究,磁性材料的选取在电感量一定的情况下要保证电感不饱和,磁损耗要小。
滤波器参数 SPWM逆变器的输出LC滤波器主要用来滤除开关频率及其邻近频带的谐波,一个滤波 器的性能优劣主要取决于它对谐波的抑制能力,具体要从THD值来分析,另外要尽量 减少滤波器对逆变器的附加电流应力,电流应力增大,除了器件损耗及线路损耗加大 外,也使功率元件的容量加大,但要求THD值较小与滤波器附加的电流应力往往相矛 盾,实际的参数还要到具体线路里调节。下面从分析二阶滤波器的特性来设计滤波器。 忽略电感的电阻及线路阻抗,滤波器的输出电压相对于逆变桥输出电压的传递函数为:
1 2 Vo (s) LC n G(s) 2 1 s 2 n s n2 Vi (s) 2 1 s s RC LC
PWM基本原理与控制 逆变过程需要控制开关管的动作模式,使得输出为波形为正弦波。设计采用的SPWM 方法对开关管进行控制。在ROM中的PWM数据时离线计算,灵活性大。取得SPWM 的方法是通过利用规则采样方法计算数据,准确地得到开关器件的导通、关断时间, 其原理误差与存储数据时取整带来的误差相比可以忽略。计算程序的入口参数主要有3 个,即载波频率 、调制频率 和调制度M,其中调制度代表预期的输出幅值。按SPWM 基本原理,自然采样法中要求解复杂的超越方程,难以在实时控制中在线计算,故工 程应用不多。而规则采样发是一种工程实用方法,效果接近自然采样法,计算量小得 多。规则采样法原理如图所示,三角波两个周期值之间为一个采样周期 ,自然采样法 中,脉冲中点不合三角波一周期中点重合,规则采样法使两者重合,即每个脉冲中点 为相应的三角波中点,使计算大为简化。三角波负峰时刻 对信号波采样取得D点,过 D作水平线和三角波交与A、B点,在A点时刻 和B点时刻 控制器件的通断。脉冲宽度 和用自然采样法得到的脉冲宽度非常接近自然采样波形。 通过实时计算生成电压SPWM需要数学模型,建立数学模型的方法有多种,比如谐波 消去法、等面积法、采样型SPWM法以及他们派生出来的各种方法。本文介绍的生成 SPWM波采用的是不对称规则采样法,不对称规则采样法是用阶梯波去逼近正弦波, 每个载波周期内采样两次,既在三角波的顶点对称轴位置采样,又在三角波的底点对 称轴位置采样,由于这样采样所形成的阶梯波与三角波的交点不对称,故称其为不对 称规则采样法,如图3-2-1所示。此法所形成的阶梯波与正弦波的逼近程度大大提高, 所以谐波分量的幅值更小,在实际中得到了较多的应用。
AIMS Power 5000瓦逆变器说明书

DC TO AC POWER INVERTER PWRINV5K24012WInstruction ManualIntroductionThe AIMS Power 5000 Watt inverter is the most advanced line of mobile DC to AC power systems available. This model is used in a wide range of applications including back up power for remote homes, off-grid systems, RVs, boats, commercial vehicles and mobile businesses. The 5000 Watt 240 Volt AC, 12 Volt DC inverter will operate most pumps, motors, and tools requiring 240V. This inverter only puts on 240 VAC single phase.To get the most out of the power inverter, it must be installed and used properly. Readthe instructions in this manual before installing and using this model.FUNCTIONSFRONT VIEWA. On/Off switch: Leave in the OFF position during installation.B. Over temperature indicator: Lights when inverter protects itself against overheating. Invertershuts down while indicator is on. Inverter will restart automatically and indicator will turn off when the inverter cools.C. Over load indicator: Lights when inverter shuts down because of overload. Indicator will turn offand inverter will restart when overload is removed.D. Bar meters: Displays battery voltage and current. Current should be in the green zone forcontinuous operation. The inverter will operate for several minutes when the current is in the yellow zone. Operation with battery voltage or current in the red zone of a meter will result in protective shutdown of inverter.E. AC outlets: Maximum recommended output per outlet is 1500W. Use AC direct connectterminal block for full 5000 watts.F. Remote port: Used with remote switch to turn inverter ON/OFF (sold separately).G. AC terminal block: Hard wire block providing inverter's full power.E: AC outletsD: Bar meters B: Over temperature indicator A: On/Off switchC: Over load indicator F: Remote PortG: AC terminal blockREAR VIEWA: Fan: Do not obstruct, allow at least 12 inch for air flow.B: Battery terminals: Connect to 12V battery (s) or other DC power source. "+" is positive & " - " isnegative. Reverse polarity connection will blow internal fuse and may damage inverter permanently. Make sure you check your input voltage and do not REVERSE POLARITY! This will void the warranty. C: Chassis ground lug: Connect to earth ground or to vehicle chassis using #8 AWG wire. Warning! Operation of the inverter without a proper ground connection may result in an electrical safety hazard.QUICK HOOK-UP AND TESTINGIf you would like to quickly hook-up the power inverter and check its performance before going ahead with your installation, please follow these guidelines:1. Unpack and inspect the power inverter, check to see that the power switch is in the OFF position.2. Before you connect the battery cables, make sure the power switch is in the off position. Connect Red (+) battery cable to Red (+) inverter terminal. Connect Black (-) battery cable to Black (-) inverter terminal. Connect Red (+) battery cable to Red (+) battery terminal. Connect Black (-) battery cable to Black (-) battery terminal. Alligator clamp cables may be used but only to connect to the battery. Do not use clamps on inverter terminals. Alligator clamps are not a permanent solution. You may see a spark during connection. Do not reverse the polarity. This may damage the inverter and void warranty. Caution! Loosely tightened connectors result in excessive voltage drop and may cause overheated wires and melted insulation. Reverse polarity connection will blow a fuse in inverter and may permanently damage the inverter. Damage caused by reverse polarity connection is not covered by our warranty. Warning! You may observe a spark when you make this connection since current may flow to charge capacitors in the power inverter. Do not make this connection in the presence of flammable fumes, as explosion or fire may result.3. Set the power switch to the on position. Check the meters and indicators on the front panel of the inverter. The voltage bar graph should indicate 11 to 14 volts depending on the voltage of the power source. If it does not, check your power source and the connections to inverter.A: FanB: Battery terminal (+)B: Battery terminal (-)C: Chassis groundingThe other indicators should be off.4. Set power inverter switch to the OFF position, the indicator l ights may blink and theinternal alarm may sound momentarily. This is normal. Plug the test load into the ACreceptacle on the front panel of the inverter. Leave the test load switch off.5. Set power inverter switch to the ON position and turn the test load on, the inverter shouldsupply power to the load. If you plan to measure the true output R.M.S. voltage of inverter, ameter such as FLUKE 87A, BACKMAN 4410 or TRIPLETT 4200 must be used.INSTALLATION1. Where to installThe power inverter should be installed in a location that meets the following requirements:a. Dry - Do not allow water to drip or splash onto the inverter.b. Cool - Ambient air temperature should be between 0°C and 40°C, the cooler the better when operating in this rangec. Ventilation - Allow at least 12 inches of clearance around the inverter for air flow. Ensure the ventilation openings on the rear and bottom of the unit are not obstructed.d. Safety - Do not install the inverter in the same compartment as batteries or in any compartment capable of storing flammable liquids such as gasoline.2. CablesDC to AC inverters require high amperage/low voltage DC power to low amperage/high voltage AC power. To operate properly, connect inverter DC input terminals direct to battery with heaviest wire available see chart below:12 Volt Model: 1 x set of 4/0 AWG (1 red + 1black) Recommended: 1ANL500KIT-500Amp fuse kit24 Volt Model: 1 x set of 1/0 AWG (1 red + 1black) Recommended: 1ANL300KIT-300Amp fuse kit36 Volt Model: 1 x set of 4 AWG (1 red + 1black) Recommended: 1ANL150KIT-150Amp fuse kit48 Volt Model: 1 x set of 6 AWG (1 red + 1black) Recommended: 1ANL150KIT-150Amp fuse kitBattery Cables InstallationWhen connecting the AC inverter to the battery terminals, it is important to connect the "+" wire to the "+" terminal and the wire to the"-" wire to the “-“ terminal. Do NOT reverse the polarity. It will void the warranty. Make sure you connect negative to negative and positive to positive.Red (+)Black (-)REDBLACKCaution!DO NOT allow the wires to cross or touch each other. Install the cables facing away from each other and screw tightly. When connecting the battery cables to the terminals of the inverter, make sure they do not touch the case.3. GroundingThe power inverter has a lug on the rear panel marked "chassis ground" This is to connect the chassis of the power inverter to the ground.The ground terminals in the AC outlets on the front panel of the inverter are also connected to the ground lug.The chassis ground lug must be connected to a grounding point, which will vary depending on where the power inverter is installed. In a vehicle, connect the chassis ground to the chassis of the vehicle. In a boat, connect to the boat's grounding systems in a fixed location, connect the chassis ground lug to an earth point, which will vary depending on where the power inverter is installed.The neutral (common)conductor of the power inverter AC output circuit is connected to the chassis ground. Therefore, when the chassis is connected to ground, the neutral conductor will also be grounded.This conforms to national electrical code requirements that separately derived AC sources (such as inverters and generators) have their neutral tied to ground in the same way that the neutral conductor from the utility line is tied to ground at the AC breaker panel.Caution! The Negative DC input of the power inverter is connected to the chassis. DO not install the power inverter in a positive ground DC system. A positive ground DC system has the positive terminal of the battery connected to the chassis of the vehicle or to the grounding point.Warning! Do not operate the power inverter without connecting it to ground. Electrical shock hazard may result.OPERATIONTo operate the power inverter, turn it on using the ON/OFF switch on the front panel. The power inverter is now ready to deliver AC power to your loads. If you are operating several loads from the power inverter, turn on separately after the inverter has been turned on. This will ensure that the power inverter does not deliver starting currents to all of the loads at once.1. Controls and indicatorsThe ON/OFF switch turns the control circuit in the power inverter on and off. It does not disconnect power from the power inverter.When the switch is in the OFF position, the power inverter draws no current from battery. When the switch is in the ON position but with no load, the power inverter draws less than 450 mA.2. Battery voltage indicatorThe battery voltage bar graph indicates the voltage at the input terminals of the power inverter. At low input current, this voltage is very close to the battery voltage. At high input current, this voltage will be lower than the battery voltage because of the voltage drop across the cable and connections.Ideally, the voltage should remain in the green area of the bar graph. If the voltage goes into the red area at top or bottom of the graph, inverter may shut-down.3. Battery current indicatorThe battery current bar graph indicates the current drawn from the battery by the power inverter, it will not indicate current by other loads also connected to the battery. The indicator only displays DC volts and amps.For long term operation, the current should be in the green area of the bar graph. Short term operation is possible with current in the orange area. If the current rises to the red area, the inverter will reduce its output voltage to protect itself.4. Over temp indicatorThe over temp indicator indicates that the power inverter has shut itself down because it has become overheated. The power inverter may overheat because it has been operated at power levels above its rating, or because it has been installed in a location which does not allow it to dissipate heat properly.5. Over load indicatorThe over load indicator indicates that the power inverter has shut itself down because its output circuit has been short circuited or drastically overloaded. Switch the ON/OFF to OFF, correct the fault condition, and then switch the ON/OFF back to ON.THINGS TO CONSIDER REGARDING THE LOADThe 5000W inverter will operate most AC loads within its power rating. When determining whether a microwave oven can be operated by the 5000W inverter, remember that the power commonly advertised for microwave ovens is the cooking power (the power delivered to the food) not the power actually consumed by the microwave oven. The microwave oven will consume 40% to 100% more than its advertised cooking power. Check the rating sticker on the back of the oven to determine its actual power draw. The 5000W inverter will operate small microwave ovens (0.2 to 0.3 cubic foot capacity) that draw is about 1700 watts.Some induction motors used in refrigerators, freezers, pumps, and other motor operated equipment require very high surge currents to start. The power inverter may not be able to start some of these appliances even though their rated current draw is within the rating of the power inverter.If a motor refuses to start, observe the battery voltage indicator while trying to start the motor. If the battery voltage indicator drops below 10.5V DC while inverter is attempting to start the motor, this may be why the motor won't start.Make sure that the battery connections are good and that the battery is fully charged. If the connections are good and the battery to is charged, but the voltage still drops below 11 volts, you may need a larger battery or larger battery bank.INPUT VOLTAGEThe power inverter will operate from input voltage ranging from 10V-16V. If the voltage drops below input range, an audible low battery warning will sound and the voltage indicator will be in the lower red zone. The power inverter will shut down if the input voltage drops below 10V, or 20V, or 30V, or 40V +/- .5V depending on model. This protects your battery from being over discharged.The power inverter will also shut down if the input voltage exceeds 17V +\-.5V. This protects the inverter against excessive input voltage.The voltage indicator will be in the upper red zone. Although the power inverter incorporates protection against over voltage, the inverter is at risk of permanent damage if the input voltage is allowed to exceed 17V +\-.5V depending on model.TROUBLESHOOTINGmon problemsa. Buzz in audio systems:Some inexpensive stereo systems and radios will emit a buzzing noise from their loudspeakers when operated from the power inverter. This is because the power supply in the device does not adequately filter the modified sine wave produced by the power inverter. The only solution is to use a sound system that incorporates a higher quality power supply.b. Television interference:Operation of the power inverter can interfere with television reception on some channels. If this situation occurs, the following steps may help to alleviate the problem.-Make sure that the chassis ground lug on the back of the power inverter is solidly connected to the ground system of your vehicle, boat or home.-Do not operate high power loads with the power inverter while watching television.-Make sure that the antenna feeding your television provides an adequate ("snow free") signal and that you are using good quality cable between the antenna and the television.-Move the television as far away from the power inverter as possible.-Keep the cables between the battery and the power inverter as short as possible and twist them together with about 2 to 3 twists per foot. This minimizes radiated interference from the cables.SPECIFICATIONSAIMS Corp., Inc. dba AIMS Power Warranty Instructions:This product is designed using the most modern digital technology and under very strict quality controland testing guidelines. If, however, you feel this product is not performing as it should, please contact us:**************************(775)359-6703We will do our best to resolve your concerns. If the product needs repair or replacement, make sure to keep your receipt/invoice, as that will need to be sent back along with the package and RMA# prepaid to AIMS. You have a full 1 year warranty from date of purchase.This warranty is valid worldwide with the exception that freight and duty charges incurred outside the contiguous 48 United States will be prepaid by customer.Except as provided above, AIMS makes no warranty of any kind, express or implied, including without limitation the implied warranties of merchantability and fitness for a particular purpose. In no event shall AIMS be liable for indirect, special or consequential damages. This warranty only applies to AIMS Power branded products. All other name brand products are warranted by and according to their respective manufacturer. Please do not attempt to return non-AIMS Power branded products to AIMS Power.For additional products such as:-Modified sine wave inverters-Pure sine wave inverters-Low Frequency Inverters-Solar Charge Controllers-Micro Grid Tied Inverters-Inverter Chargers and Automatic transfer switches-Converters DC-DC-Custom cut cables-Batteries-Solar Panels & RacksPlease visit our web site: Tofindoutwheretobuyanyofourproducts,youmayalsoe-mail:************************(775)359-6703.。
电源、变频电源 5kva、变频电源 5kw

电源|变频电源5kva|变频电源5kw 指导老师:欧阳华斯电源答辩人:5KVA变频电源技术参数(OYHS-9805)产品共同特点输出电压:0-300V连续可调输出频率:60HZ,50HZ,40-499.9HZ连续可调超臷能力强,瞬间电流可承受三倍额定电流故障时一键停机功能,反应速度快,反应时间在2ms以内具有过流,过压,过温,短路,过载等多重保护及报警功能高精度的稳频稳压功能,快速调节电压,频率主要元器件均采用原装进口品牌,品质可靠单进单出变频电源技术参数型号(OYHS)OYHS-9805输出容量(5KVA)5KVA电路方式IGBT/SPWM脉宽调制方式交流输入相数单相波形SINEWAWE电压220V±15%频率波动范围50HZ or60HZ±10%功率因数﹥0.9交流输出相数单相波形SINE WAVE低档电压0-150V高档电压0-300V频率60HZ,50HZ,40-499.9HZ连续可调频率稳定率≤0.01%低档最大电流(A)42A(0-150V)高档最大电流(A)21A(150-300V)整机性能电源稳压率﹤1%负载稳压率﹤1%波形失真度﹤1%效率﹥90%反应时间≤2ms波峰因子3:1保护装置具有过压,过流,超载,输入欠压,过高温,短路等多重保护显示显示介面数位式LED显示电压4位数,数位电压表,解析度0.1V电流4位数,数位电流表,解析度0.1A功率4位数,数位瓦特表频率4位数,数位频率表环境及其它冷却装置高速变频风扇冷却,强制冷风工作温度-10℃to50℃相对湿度0~90%(非凝结状态)海拔高度≤1500m重量(KG)70尺寸(H*D*W)mm600*530*350注:1以上尺寸不含脚输高度2可根据顾客要求规格特别定制3本公司产品规格不断研发改进,规格若有变更,恕不另行通知。
电力变压器变频电源使用说明书

HZBP-III 变频电源使用手册武汉合众电气欢迎使用武汉市合众电气设备制造有限公司产品尊敬的顾客感谢您使用本公司的产品。
在您初次使用设备前,请您详细地阅读本使用说明书,将可帮助您熟练地使用我公司设备。
我们的宗旨是不断地改进和完善公司的产品,因此您所使用的设备可能与使用说明书有少许的差别。
如果有改动的话,我们会用附页方式告知,敬请谅解!您有不清楚之处,请与公司售后服务部联络,我们定会满足您的要求。
由于试验设备均有可能带电压,您在插拔测试线、电源插座时,会产生电火花,小心电击,避免触电危险,注意人身安全!◆慎重保证本公司生产的产品,在发货之日起三个月内,如产品出现缺陷,实行包换。
三年内如产品出现缺陷,实行免费维修。
三年以上如产品出现缺陷,实行有偿终身维修。
如有合同约定的除外。
◆安全要求请阅读下列安全注意事项,以免人身伤害,并防止本产品或与其相连接的任何其它产品受到损坏。
为了避免可能发生的危险,本产品只可在规定的范围内使用。
只有合格的技术人员才可执行维修。
—防止火灾或人身伤害使用适当的电源线。
只可使用本产品专用、并且符合本产品规格的电源线。
正确地连接和断开。
当设备连线处联机状态时,请勿随意连接或断开测试导线。
产品接地。
本产品除通过电源线接地导线接地外,产品外壳的接地柱必欢迎使用武汉市合众电气设备制造有限公司产品须接地。
为了防止电击,接地导体必须与地面相连。
在与本产品做联机试验前,应确保本产品已正确接地。
注意所有终端的额定值。
为了防止火灾或电击危险,请注意本产品的所有额定值和标记。
在对本产品进行连接之前,请阅读本产品使用说明书,以便进一步了解有关额定值的信息。
请勿在无产品盖板时操作。
如盖板或面板已卸下,请勿操作本产品。
使用适当的保险丝。
只可使用符合本产品规定类型和额定值的保险丝。
避免接触裸露电路和带电金属。
产品有电时,请勿触摸裸露的接点和部位。
在有可疑的故障时,请勿操作。
如怀疑本产品有损坏,请本公司维修人员进行检查,切勿继续操作。
SAJ变频器5.5KW说明书

变频器配线部分,分为主回路和控制回路。
用户可将外壳的盖子掀开,此时可看到主回路端子和回路端子,用户必须依照下列的配线回路准确连接。
备注:(1)如果只有dcm端子,则acm端子等效于dcm端子。
(2)am端子等效于fm端子(am为可选端子)。
三、操作及运行1、操作说明(1)键盘说明(2)状态提示灯功能hz:当led显示内容为频率数据时,该指示灯亮。
i:当led显示内容为电流数据时,该指示灯亮。
fwd:当变频器处于正转运行时,该指示灯亮。
rev:当变频器处于反转运行时,该指示灯亮。
(3)监视运行参数变频器在运行过程中,按一次“data”键,再按“▲”或“▼”键选择观看运行电流或运行频率。
hz灯亮表示频率,i灯亮表示电流。
(4)查看故障记录变频器在运行过程中或待机状态下,按两次“prgm”键,再按“▲”或“▼”键可逐次观看最近4次故障记录。
观看完后按“data”键,变频器复位。
(5)参数修改步骤变频器在待机状态下:步骤1:按“prgm”键,变频器显示“fxxx”,“xxx”为参数号。
步骤4:按“▲”或“▼”键修改该参数值,按“stop/reset”键可以移动光标位置。
步骤5:按“rd/wt”键把数值设定。
如欲修改其它参数,请重复步骤1~5即可。
备注:要修改re/wt类型的参数时必须先把f096设为“1”。
2、操作范例(1)修改参数(将f002的参数值从10s改为5s)。
变频器通电后,键盘显示“0.00”,按一次“prgm”键,键盘显示“f000”;按“▲”键调到“f002”,按一次“rd/wt”键,读出该参数内容,键盘显示“10.0”,按“▼”键把“10”改为“5”,在按一次“ed/wt”键设定,然后按“data”键即可。
(2)变频器参数初始化变频器通电后,键盘显示“0.00”,按一次“prgm”键,键盘显示“f000”,然后按“▲”键把“f000”调到“f094”,再按一次“rd/wt”键,键盘显示“0”,按“▲”键改为“1”,按“rd/wt”键设定,再按两次“prgm”键,键盘显示“0.--”,然后在按一次“stop/reset”键,变频器开始初始化。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
D、EMI/EMC 安规测试标准电源。
3、精密度仪器设备的专用电源:
A、高精度之仪器使用电源,能使各种功能完完整整的表现出来。
B、整厂设备输出,事前模拟,促进设备之全功能化。
C、制造无障碍设备的专属电源。
使用产品介绍:
电脑(PC)
空调设备
监视器(Monitor)
日光灯安定器测试
电脑用直明
(单相机型)
12 3 4 56 7 89
12 13 11
14
15
(三相机型)
■安装说明
变频电源的几种型号是否符合您订购之型号与容量。 变频电源是否因运送不慎造成损坏,若有损坏请勿接上电源。
确认入电电压是否和机器规格相符合。 勿将机器装置於靠近水源、高温、潮湿场所。 防止油雾、盐分侵蚀。 防止粉尘、棉絮及金属细物侵入。 让机器远离尘埃、闷热及换气不良的场所,并保持环境清洁。 安装机器时请注意机器背面散热空间距离,以避免散热不良。 机器请放置於坚固及没有振动的水平面上。 安装前请先参考背面之规格。 使用前确定输入电压。 接上电源之前须注意 L-N-G(单相)规格是否正确,R-S-T(三相) 之相序装接,切勿接反。 在接电源之前先将所有开关置於 OFF 以确保设备无损害之虞。 配线时注意所有接线端之插头、插座,有无松动以避免导电不良产生
此按钮重新启动。 7.频率指拨开关:固定频率 40.0-499.9HZ 可程式(指拨)设定。 8.输出电压切换开关:二档 0-150V 或 0-300V。 9.标准电压输出微调钮:十转式微调开关,可由微调得到您所需要的
标准电压。
10.三相输出电流显示切换开关:可切换显示各相之输出电流值。(仅 用於三相输出机种)。
单进单出变频电源(OYHS-9800 系列)
����������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������������