模具英语词汇表汇编
模具专业术语英语
模具专业术语英语
模具专业涉及许多专业术语，在英语中对应的词汇如下：
1. Mold/Mould: 模具
2. Die: 模具，尤指金属冲压模
3. Cavity: 模穴
4. Core: 模芯
5. Runner: 喷嘴，注塑道
6. Gate: 浇口，进料口
7. Ejector Pin: 顶针，用于将制品从模具中推出
8. Injection Molding: 注塑成型
9. Blow Molding: 吹塑
10. Compression Molding: 压缩成型
11. Extrusion Molding: 挤出成型
12. Casting: 铸造
13. Hot Runner: 热流道系统
14. Cooling Channel: 冷却通道
15. Draft Angle: 脱模锥度
16. Shrinkage: 收缩率
17. Surface Finish: 表面处理/光洁度
18. Undercut: 模具槽，模具凹槽
这些词汇在模具制造和加工过程中经常使用，涵盖了模具设计、制造和加工等方面的专业术语。
模具专业的英语词汇大全
模具专业的英语词汇大全一、模具专业英语入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate细水口： pin-point gate 水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate 圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue 热流道板：hot manifold发热管：cartridge heater 探针: thermocouples插头：connector plug 插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw 管钉：dowel pin开模槽：ply bar scot 内模管位：core/cavity inter-lock顶针：ejector pin 司筒：ejector sleeve司筒针：ejector pin 推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter模胚（架）： mold base 上内模：cavity insert下内模：core insert 行位（滑块）： slide镶件：insert 压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar 唧嘴： sprue bushing挡板：stop plate 定位圈：locating ring锁扣：latch 扣鸡：parting lock set推杆：push bar 栓打螺丝：S.H.S.B顶板：eracuretun 活动臂：lever arm分流锥：spure sperader 水口司:bush垃圾钉：stop pin 隔片：buffle弹弓柱：spring rod 弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin 销子：dowel pin波子弹弓：ball catch模具成形不良用语英汉对照aberration 色差atomization ?化bank mark ?料纹 bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜low hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形 edge切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔 mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹各式模具分类用语英汉对照landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模各种模具常用成形方式英汉对照accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模机械类常用英语：冲压模具-零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块机械类常用英语：冲压模具-模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板冲压模具-冲压名称类英汉对照plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量。
模具英语词汇表
模具专业英语词汇landed plunger mold 有肩柱塞式模具burnishing die 挤光模整形冲模landed positive mold 有肩全压式模具button die 镶入式圆形凹模，模具镶套loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具injection mold 注塑模rubber molding 橡胶成形hot chamber die casting 热室压铸sand mold casting 砂模铸造extrusion mold 挤出模multi-cavity mold 多模穴模具palletizing die 叠层模plaster mold 石膏模three plates mold 三板模plain die 简易模pierce die 冲孔模forming die 成型模gang dies 复合模shearing die 剪边模riveting die 铆合模compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模runner system浇道系统sprue/cold material trap 浇道/冷料井sprue puller 拉杆runner design 流道设计main runner 主流道secondary runner 次流道gate design 浇口设计submarine gate 潜伏浇口tunnel gate 隧道式浇口pinpoint gate 点浇口fan gate 扇形浇口side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口dish gate 盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣insulated runner/hot runner 热浇道runner plat 浇道模块valve gate阀门浇口slag well 冷料井cold slag 冷料渣sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆)注塑缺陷：flash 飞边warpage 翘曲air trap 积风blush 发赤flow line 流痕splay 银纹short shot 短射sink mark 缩痕streak 条纹void 缩孔weld line 熔接线gas mark 烧焦cold slug 冷斑delamination 起皮flaw/scratch 刮伤gloss 光泽glazing 光滑surface check 表面裂痕hesitation 迟滞注塑工艺:molding conditions 成型条件drying 烘干barrel temperature 料筒温度melt temperature 熔化温度mold temperature 模具温度injection pressure 注塑压力back pressure 背压injection speed 注塑速度screw speed 螺杆转速tensile strength 抗拉强度tensile elongation 延伸率flexural modulus 弯曲模数flexural strength 抗弯强度shrinkage 收缩率regrind usage 次料使用机械设备:lathe车床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机punching machine 冲床robot机械手common equipment常用设备EDM=Electron Discharge Machining 放电加工3D coordinate measurement 三次元量床boring machine 搪孔机milling machine 铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床cylindrical grinding machine 外圆磨床die spotting machine 合模机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床模具零件:top plate上托板（顶板）punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate 唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot 撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate 不准用镶件：Do not use (core/cavity) insert 用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodAabrasion n. 磨损mósǔnabrasion resistance n. 耐磨损性nài mósǔn xìng abrasive n. 磨料móliàoaccelerator n. 促进剂cùjìnjìaccuracy n. 准确性zhǔnquèxìngacrylic n. 丙烯酸bǐngxīsuān，压克力yākelì additive n. 添加剂tiānjiājìadhere v. 黏附niánfùadhesion n. 黏合niánhéadhesive n. 胶粘剂jiāozhānjìair entrapment n. 困气kùnqìanneal v. 退火tùihuǒassemble v. 总成zǒngchéngBbarrel n. 机筒jītǒng，料筒liàotǒngblow molding n. 吹塑成型chūisù chéngxíng blow molding machine n. 吹塑机chūisùjī brittle adj. 脆性cùixìngbubble n. 气泡qìpàoby-product n. 副产品fùchǎnpǐnCcalendering n. 压延yāyáncarbon steel n. 碳素钢tànsù gāngcasting n. 铸造zhùzàocatalyst n. 催化剂cūihuàjìcavity n. 型腔xíngqiāngchemical resistance n. 耐化学腐蚀性nài huàxué fǔshí xìngchip v. 削xiāo，凿záoclamping force n. 锁模力suǒmólìclamping tonnage n. 锁模吨位suǒmódūnwèicomputer aided design (CAD) n. 电脑辅助设计diànnǎo fǔzhù shèjìcomputer aided manufacture (CAM) n. 电脑辅助制造diànnǎo fǔzhù zhìzào computer numerical control (CNC) n. 电脑数字控制diànnǎo shùzì kòngzhìceramic n. 陶瓷táocícold rolled steel n. 冷轧圆钢lěng zháyuán gāngcold runner n. 冷流道lěng liúdàocolorant n. 着色剂zhuósèjìcomposite n. 复合材料fùhé cáiliàocompression strength n. 抗压强度kàngyā qiángdùcooling channel/circuit n. 冷却管道lěngquè guǎndàocooling rate n. 冷却速率lěngquè sùlǜcore n. 型芯xíngxīn，模芯móxīncorrosion n. 腐蚀fǔshícorrosion resistance n. 耐腐蚀性nài fǔshí xìngcure v. 固化gùhuàcustom adj. 定制dìngzhìcycle time n. 循环时间xúnhuán shíjiānDdegassing n. 排气páiqìdensity n. 密度mìdùdeform v. 变形biànxíngdie n. 冲模chòngmódie casting n. 压铸yāzhù，模铸mózhùdimension n. 尺寸chǐcùndimensional tolerance n. 尺寸公差chǐcùn gōngchàdistort v. 扭曲niǔqūdraft angle n. 拨模斜度bōmó xiédùdwell time n. 驻留时间zhùliú shíjiāndye n. 染料ránliàoEejector mark n. 顶出痕迹dǐngchū hénjìejection pin n. 顶出杆dǐngchū gān，推顶锁tūidǐng suǒ，脱模锁tuōmó suǒejection plate n. 推顶板tūidǐng bǎn，脱模板tuōmó bǎnejection rod n. 脱模板拉杆tuōmó bǎn lāgānelastomer n. 弹性体tánxìngtǐelectrical discharge machining (EDM) n. 电火花加工diànhuǒhuā jiāgōng epoxy n. 环氧树脂huányǎngshùzhīextruder n. 挤出机jǐchūjīextrusion n. 挤出jǐchū，挤塑jǐsùFfabricate v. 制造zhìzàofiber n. 纤维xiānwéifiberglass n. 玻璃纤维bōli xiānwéifiber reinforcement n. 纤维增强xiānwéi zēngqiángfilm n. 薄膜báomófire retardant n. 阻燃剂zǔránjìflash n. 溢料yìliàoflow mark n. 流痕liúhénflow rate n. 流动速率liúdòng sùlǜfluorescent adj. 荧光yíngguāngfluorescent brightener n. 荧光增白剂yíngguāng zēngbáijìfoam n. 泡沫pàomòfuse v. 熔合rónghéGgas assisted injection molding n. 气辅注射成型qìfǔzhùshè chéngxíng gate n. 浇口jiāokǒugate mark n. 浇口痕jiāokǒu héngear n. 齿轮chǐlúngrinder n. 研磨机yánmójī，磨床móchuángHheat conduction n. 热传导rè chuándàoheater band n. 加热圈jiārè quānheat treatment n. 热处理rè chǔlǐhigh density polyethylene (HDPE) n. 高密度聚乙烯gāo mìdù jùyǐxī high impact plastic n. 高抗冲塑料gāo kàngchòng sùliàohigh impact polystyrene n. 高抗冲聚苯乙烯gāo kàngchòng jùběnyǐxī hobbing n. 滚铣gǔnxǐ，挤压制模jǐyā zhìmó，切压制模qiēyā zhìmó holding n. 保压bǎoyāhot runner n. 热流道rè liúdàoIimpact strength n. 冲击强度chòngjī qiángdùinjection n. 注射zhùshè，注塑zhùsùinjection molding n. 注塑成型zhùsù chéngxínginjection molding machine n. 注塑机zhùsùjīinjection pressure n. 注塑压力zhùsù yālìinsulated runner n. 绝热流道juérè liúdào，保温流道bǎowēn liúdào insulation layer n. 绝热层juérè cénginternally heated runner n. 内加热流道nèi jiārè liúdàointernal void n. 内部空腔nèibù kōngqiāngJjoint n. 接头jiētóu，连接liánjiēLlaser n. 激光jīguānglaser cutter n. 激光切割机jīguāng qiēgējīlathe n. 车床chēchuánglocating pin n. 定位锁dìngwèi suǒlow density polyethylene n. 低密度聚乙烯dī mìdù jùyǐxīMmelt v. 熔融róngróngmelt index n. 熔融指数róngróng zhǐshùmill (metal) v. 铣xǐmachining n. 机加工jījiāgōngmachining path n. 加工路径jiāgōng lùjìngmanufacture v. 制造zhìzàomeld line n. 融合线rónghé xiànmetal machining n. 金属加工jīnshù jiāgōngmilling machine n. 铣床xǐchuángmodel n. 模型móxíngmonomer n. 单体dāntǐmold n. 模具mójùmold cavity n. 模具型腔mójù xíngqiāngmold life n. 模具寿命mójù shòumìngmulticavity mold n. 多腔模具duōqiāng mójù multicolor injection molding n. 多色注塑duōsè zhùsù multigate mold n. 多浇口模具duōjiāokǒu mójùmultishot injection molding n. 多色注塑duōsè zhùsùNnozzle n. 喷嘴pēnzǔiNylon n. 尼龙NílóngOoxidation resistance n. 耐氧化性nài yǎnghuà xìng oxidize v. 氧化yǎnghuàPpackaging n. 包装bāozhuāngpacking n. 补料bǔliàoparison n. 型坯xíngpīpart n. 零件língjiànparting line n. 分模线fēnmóxiànparting plane n. 分模面fēnmómiànpinhole gate n. 针孔形浇口zhēnkǒngxíng jiāokǒuplastic n. 塑料sùliàoplasticity n. 塑性sùxìngplasticizer n. 增塑剂zēngsùjìplotter n. 绘图机hùitújīpolish v. 抛光pāoguāngpolycarbonate (PC) n. 聚碳酸酯jùtànsuānzhǐpolyethylene n. 聚乙烯jùyǐxīpolyester n. 聚酯jùzhǐpolymer n. 聚合物（体）jùhéwù(tǐ)，高聚物gāojùwù polymerization n. 聚合jùhépolystyrene n. 聚苯乙烯jùběnyǐxīpolyurethane n. 聚氨脂jù'ānzhīpolyvinyl chloride (PVC) n. 聚氯乙烯jùlǜyǐxīporous adj. 多孔duōkǒngprecise adj. 精密jīngmìprecision n. 精度jīngdùprecision injection machine n. 精密注塑机jīngmì zhùsùjī precision molding n. 精密模塑jīngmì mósùpreform n. 预成型yùchéngxíngpreform molding n. 预成型模塑yùchéngxíng mósùprocess v. 处理chǔlǐ；加工jiāgōngproduction line n. 生产线shēngchǎnxiànprototype n. 原型yuánxíngpunch n. 冲头chòngtóuQquench v. 淬火cùihuǒRregrind n. 回用料húiyòngliàoresin n. 树脂shùzhīrib n. 肋条lèitiáorib stiffener n. 加强肋jiāqiáng lèirigidity n. 刚性gāngxìngripple n. 波纹bōwén，皱纹zhòuwénrough adj. 粗糙cūcāorubber n. 橡胶xiàngjiāo；橡皮xiàngpírunner n. 流道liúdàorunnerless adj. 无流道wúliúdàorunnerless injection mold n. 无流道注塑模具wúliúdào zhùsù mójùSscale n. 比例bǐlìschematic n. 图解tújiěseal v. 密封mìfēngshort shot n. 短射duǎnshè，欠料注射qiànliào zhùshèshot n. 注料zhùliào，注射zhùshèshot size n. 注塑量zhùsùliàngshrinkage n. 收缩shōusuōside core n. 侧性芯cèxìngxīnside gate n. 侧向浇口cèxiàng jiāokǒusilicone n. 聚硅氧烷jùgūiyǎngwánsilicone rubber n. 硅橡胶gūixiàngjiāosimulate v. 模拟mónǐsingle cavity mold n. 单腔模具dān qiāng mójùsingle gate mold n. 单浇口模具dān jiāokǒu mójùsink mark n. 凹痕āohén，缩痕suōhénslide n. 滑动阀huádòngfásoftener n. 软化剂ruǎnhuàjìsprue n. 注道zhùdàosteam channel n. 汽道qìdàostabilizer n. 稳定剂wěndìngjìstamping n. 冲压chòngyāstainless steel n. 不锈钢bùxiùgāngstrain n. 应变yìngbiànstreak n. 条纹tiáowén，条痕tiáohénstress n. 应力yìnglìstripper n. 脱模器tuōmóqì，顶出器dǐng chūqìstripper ring n. 脱模圈tuōmóquānsurface defect n. 表面缺陷biǎomiàn quēxiànsurface treatment n. 表面处理biǎomiàn chǔlǐsymmetrical adj. 对称dùichēngsymmetry n. 对称dùichēngTtie bar n. 连接杆l iánjiēgānTeflon n. 特氟隆Tèfúlóngtemper v. 回火hùihuǒtensile strength n. 抗张强度kàngzhāng qiángdù thermoforming n. 热成型rèchéngxíngthermoplastic n. 热塑性塑料rèsùxìng sùliào adj. 热塑性rèsùxìng thermoset n. 热固性塑料règùxìng sùliào adj. 热固性règùxìng three-dimensional adj. 三维空间sānwéi kōngjiāntolerance n. 公差gōngchàtool mark n. 刀痕dāohéntool steel n. 工具钢gōngjù gāngUultrasonic welder n. 超声波焊接机chāoshēngbō hánjiējīundercut n. 凹孔āokǒngunit cost n. 单价dānjiàVvacuum n. 真空zhēnkōngvented injection molding n. 排气式注塑成型páiqìshì zhùsù chéngxíng viscosity n. 黏度niándù，黏性niánxìngvulcanize v. 硫化liúhuàWwarpage n. 翘曲变形qiàoqū biànxíngwear n. 磨损mósǔnwear resistance n. 耐磨损性nài mósǔn xìngweld line n. 熔接线róngjiē xiànworking drawing n. 工程图根据国家标准，以下为部分塑料模具成形术语的标准翻译。
模具专业的英语词汇大全
WORD格式模具专业的英语词汇大全一、模具专业英语入水：gate进入位：gatelocation水口形式：gatetype大水口：edgegate细水口：pin-pointgate 水口大小：gatesize转水口：switchingrunner/gate唧嘴口径：spruediameter二、流道:runner热流道：hotrunner,hotmanifold热嘴冷流道:hotsprue/coldrunner:directspruegate圆形流道：round(full/halfrunnermoldflowanalysis流道平衡:runnerbalancehotsprue热流道板：hotmanifoldcartridgeheater探针:thermocouplesconnectorplug插座：connectorsocket/封料：seal三、运水：waterline喉塞：linelpug喉管：tube塑胶管：plastictube快速接头：jiffyquickconnectorplug/socker四、模具零件：moldcomponents三板模：3-platemold二板模：2-platemold/导边：leaderpin/guidepin边司/导套：bushing/guidebushingshoulderguidebushing中托边L：guidepinejectorretainnerplate托板：supportplatescrew管钉：dowelpinplybarscot内模管位：core/cavityinter-lockWORD格式ejectorpin司筒：ejectorsleeveejectorpin推板：stripperplatemovablecore,returncorecorepullernylonlatchlock斜顶：liftermoldbase上内模：cavityinsertcoreinsert行位（滑块）：slideinsert压座/斜鸡：wedge/油板：wedgewearplate压条：plate:supportpillar唧嘴：spruebushingstopplate定位圈：locatingringlatch扣鸡：partinglocksetpushbar栓打螺丝：S.H.S.Beracuretun活动臂：leverarmspuresperader水口司:bushstoppin隔片：bufflespringrod弹弓:diespringejectorguidebush中托边：ejectorguidepinpin销子：dowelpinballcatch模具成形不良用语英汉对照aberration色差atomization?化bankmark?料纹bite咬入blackinghole涂料孔(铸疵)blackingscab涂料疤WORD格式blister起泡blooming起霜lowhole破孔blushing泛白bodywrinkle侧壁皱纹breaking-in冒口带肉bubble膜泡burnmark糊斑burr毛边camber翘曲cell气泡centerbuckle表面中部波皱check细裂痕checking龟裂chipping修整表面缺陷clamp-off铸件凹痕collapse塌陷colormottle色斑corrosion腐蚀crack裂痕crazing碎裂crazing龟裂deformation变形edge切边碎片edgecrack裂边fading退色fillerspeak填充料斑fissure裂纹flangewrinkle凸缘起皱flaw刮伤flowmark流痕galling毛边glazing光滑gloss光泽greasepits污斑grindingdefect磨痕haircrack发裂haze雾度incrustation水锈indentation压痕internalporosity内部气孔mismatch偏模mottle斑点necking缩颈WORD格式nick割痕orangepeel橘皮状表面缺陷overflow溢流peeling剥离pit坑pittingcorrosion点状腐蚀platemark模板印痕pock麻点pockmark痘斑resinstreak树脂流纹resinwear树脂脱落riding凹陷sagging松垂saponification皂化scar疤痕scrap废料scrapjam废料阻塞scratch刮伤/划痕scuffing深冲表面划伤seam裂痕shockline模口挤痕shortshot充填不足shrinkagepool凹孔sinkmark凹痕skininclusion表皮折叠straightening矫直streak条状痕surfacecheck表面裂痕surfaceroughening橘皮状表皮皱折surging波动sweatout冒汗torsion扭曲warpage翘曲waviness波痕webbing熔塌weldmark焊痕whitening白化wrinkle皱纹各式模具分类用语英汉对照landedplungermold有肩柱塞式模具burnishingdie挤光模landedpositivemold有肩全压式模具buttondie镶入式圆形凹模loadingshoemold料套式模具WORD格式center-gatedmold中心浇口式模具loosedetailmold活零件模具chillmold冷硬用铸模loosemold活动式模具clodhobbing冷挤压制模louveringdie百叶窗冲切模compositedies复合模具manifolddie分歧管模具counterpunch反凸模modularmold组合式模具doublestackmold双层模具multi-cavitymold多模穴模具electroformedmold电铸成形模multi-gatemold复式浇口模具expanderdie扩径模offswtbendingdie双折冷弯模具extrusiondie挤出模palletizingdie叠层模familymold反套制品模具plastermold石膏模blankthroughdies漏件式落料模porousmold通气性模具duplicatedcavityplate复板模positivemold全压式模具fantaildie扇尾形模具pressuredie压紧模fishtaildie鱼尾形模具profiledie轮廓模flashmold溢料式模具progressivedie顺序模gypsummold石膏铸模protablemold手提式模具hot-runnermold热流道模具prototypemold雏形试验模具ingotmold钢锭模punchingdie落料模lancingdie切口模raising(embossing)压花起伏成形re-entrantmold倒角式模具sectionaldie拼合模runlessinjectionmold无流道冷料模具sectionaldie对合模具segmentmold组合模semi-positivemold半全压式模具WORD格式shaper定型模套singlecavitymold单腔模具solidforgingdie整体锻模splitforgingdie拼合锻模splitmold双并式模具spruelessmold无注道残料模具squeezingdie挤压模stretchformdie拉伸成形模sweepingmold平刮铸模swingdie振动模具threeplatesmold三片式模具trimmingdie切边模unitmold单元式模具universalmold通用模具unscrewingmold退扣式模具yoketypedie轭型模各种模具常用成形方式英汉对照accuratediecasting精密压铸powderforming粉末成形calendaringmolding压延成形powdermetalforging粉末锻造coldchamberdiecasting冷式压铸precisionforging精密锻造coldforging冷锻pressforging冲锻compactingmolding粉末压出成形rockingdieforging摇动锻造compoundmolding复合成形rotaryforging回转锻造compressionmolding压缩成形rotationalmolding离心成形dipmold浸渍成形rubbermolding橡胶成形encapsulationmolding注入成形sandmoldcasting砂模铸造extrusionmolding挤出成形shellcasting壳模铸造foamforming?泡成形sinterforging烧结锻造forgingroll轧锻sixsidesforging六面锻造gravitycasting重力铸造slushmolding凝塑成形hollow(blow)molding中空(吹出)成形WORD格式squeezecasting高压铸造hotchamberdiecasting热室压铸swaging挤锻hotforging热锻transfermolding转送成形injectionmolding射出成形warmforging温锻investmentcasting精密铸造matcheddiemethod对模成形法laminatingmethod被覆淋膜成形lowpressurecasting低压铸造lostwaxcasting脱蜡铸造matchedmouldthermalforming对模热成形模机械类常用英语：冲压模具-零件类punch冲头insert入块(嵌入件)deburringpunch压毛边冲子groovepunch压线冲子stampedpunch字模冲子roundpunch圆冲子specialshapepunch异形冲子bendingblock折刀roller滚轴baffleplate挡块locatedblock定位块supportingblockforlocation定位支承块aircushionplate气垫板air-cushioneject-rod气垫顶杆trimmingpunch切边冲子stiffeningribpunch=stinger加强筋冲子ribbonpunch压筋冲子reel-stretchpunch卷圆压平冲子guideplate定位板slidingblock滑块slidingdowelblock滑块固定块activeplate活动板lowerslidingplate下滑块板upperholderblock上压块uppermidplate上中间板springbox弹簧箱spring-boxeject-rod弹簧箱顶杆spring-boxeject-plate弹簧箱顶板bushingbolck衬套WORD格式coverplate盖板guidepad导料块机械类常用英语：冲压模具-模板类topplate上托板（顶板）topblock上垫脚punchset上模座punchpad上垫板punchholder上夹板stripperpad脱料背板upstripper上脱料板maledie公模(凸模)featuredie公母模femaledie母模(凹模)upperplate上模板lowerplate下模板diepad下垫板dieholder下夹板dieset下模座bottomblock下垫脚bottomplate下托板(底板)strippingplate内外打(脱料板)outerstripper外脱料板innerstripper内脱料板lowerstripper下脱料板冲压模具-冲压名称类英汉对照plaindie简易模piercedie冲孔模formingdie成型模progressivedie连续模gangdies复合模shearingdie剪边模rivetingdie铆合模pierce冲孔forming成型(抽凸,冲凸)drawhole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stampmark冲记号deburrorcoin压毛边WORD格式punchriveting冲压铆合sidestretch侧冲压平reelstretch卷圆压平groove压线blanking下料stampletter冲字(料号)shearing剪断tick-marknearside正面压印tick-markfarside反面压印extensiondwg展开图proceduredwg工程图diestructuredwg模具结构图material材质materialthickness料片厚度factor系数upward向上downward向下pressspecification冲床规格dieheightrange适用模高dieheight闭模高度burr毛边gap间隙weight重量totalwt.总重量punchwt.上模重量。
模具专业的英语词汇大全
模具专业的英语词汇大全一、模具基础词汇1. Mold 模具2. Die 冲模3. Core 核心模4. Cavity 型腔5. Mold Base 模架6. Mold Steel 模具钢7. Runner 流道8. Gate 进浇口9. Ejector Pin 顶针10. Ejector Plate 顶板二、模具设计相关词汇1. Draft Angle 脱模斜度2. Parting Line 分模线3. Radius 圆角4. Undercut 难以脱模的凹槽5. Slide 滑块6. Lifters 顶杆7. Cooling Channel 冷却水道8. Injection Point 注射点9. Shrinkage 收缩率10. Molding Cycle 成型周期三、模具加工与维护词汇1. Machining 加工2. Milling 铣削3. Grinding 磨削4. EDM (Electrical Discharge Machining) 电火花加工5. Wire Cutting 线切割6. Polishing 抛光7. Assembly 装配8. Maintenance 维护9. Repair 修理10. Replacement 更换四、模具材料与热处理词汇1. Tool Steel 工具钢2. Stainless Steel 不锈钢3. Aluminum 铝4. Plastic 塑料5. Rubber 橡胶6. Heat Treatment 热处理7. Hardness 硬度8. Tempering 回火9. Quenching 淬火10. Annealing 退火五、模具行业相关词汇1. Mold Maker 模具师傅2. Mold Designer 模具设计师3. Mold Manufacturer 模具制造商4. Injection Molding 注塑成型5. Blow Molding 吹塑成型6. Compression Molding 压缩成型7. Transfer Molding 传递成型8. Prototype Model 原型模具9. Mass Production 批量生产10. Quality Inspection 质量检验六、模具测试与质量控制词汇1. First Article Inspection 首件检查2. Sample 样品3. Defect 缺陷4. Dimensional Accuracy 尺寸精度5. Tolerance 公差6. Surface Finish 表面光洁度7. Stress Analysis 应力分析8. Flow Analysis 流动分析9. Mold Flow Simulation 模具流动模拟10. Quality Control 质量控制七、模具行业常用设备词汇1. Injection Molding Machine 注塑机2. Extruder 挤出机3. Blow Molding Machine 吹塑机4. CNC Machine 数控机床5. Lathe 车床6. Milling Machine 铣床7. Grinder 磨床8. EDM Machine 电火花机床9. Laser Cutter 激光切割机10. Robot 自动化八、模具生产流程词汇1. Design Drawing 设计图纸2. Mold Construction 模具构建3. Machining Process 加工工艺4. Tooling Setup 模具安装5. Trial Run 试模6. Adjustment 调整7. Production Run 生产运行8. Mold Maintenance 模具保养9. Mold Modification 模具修改10. Mold Recycling 模具回收九、模具行业认证与标准词汇1. ISO Certification ISO认证2. Quality Management System 质量管理体系3. Standard 标准化4. DIN 德国工业标准5. ASTM 美国材料与试验协会6. JIS 日本工业标准7. Certification Body 认证机构8. Audit 审核检查9. Compliance 符合性10. Continuous Improvement 持续改进十、模具行业发展趋势词汇1. Automation 自动化2. Intelligent Manufacturing 智能制造3. 3D Printing 三维打印4. Rapid Prototyping 快速原型5. Industry 4.0 工业4.06. Internet of Things (IoT) 物联网7. Big Data 大数据8. Cloud Computing 云计算9. Sustainable Development 可持续发展10. CrossIndustry Integration 跨行业整合通过这些词汇，我们可以看到模具行业不仅涉及具体的技术和操作，还包括了管理、质量控制、认证以及未来的发展趋势。
模具英语词汇表(DOC 32页)
模具英语词汇表Aabrasive grinding 强力磨削 L3abrasive[E'breisiv] a.磨料的, 研磨的 L2,3absence ['AbsEns] n.. 不在，缺席 L17accesssory[Ak'sesEri] n.附件 L10accommodate[E'kCmEdeit] v. 适应 L5accordingly[E'kC:diNli] adv.因此,从而,相应地 L7,13 accuracy['AkjurEsi] n精度,准确性 L1,3actuate['Aktjueit] vt.开动(机器), 驱动 L8adequate['Adikwit] a. 足够的 L13adhesive[Ed'hi:siv] n. 粘合剂 L22adjacent[E'dVeisnt] a. 邻近的 L13adopt[E'dCpt] vt. 采用 L4advance [Ed'vA:ns] n.进步 L7advisable [Ed'vaizbl] adj. 可取的 L20agitate['AdViteit] v. 摇动 L2a large extent 很大程度 L4,13algorithm ['Al^EriTEm] n. 算法 L6align [E'lain] v 定位，调准 L17alignment[E'lainmEnt] n. 校直 L11all-too-frequent 频繁 L17allowance[E'lEuens] n. 容差, 余量 L5alternate['C:ltEnit]v.交替,轮流 L1alternative[C:l'tE:nEtiv] n. 替换物 L3alternatively[C:l'tE:nEtivli] ad. 做为选择, 也许 L5 aluminiun[7Alju'minjEm] n.铝 L2ample['Ampl] adj. 充足的 L20analysis [E'nAlEsis] n. 分析 L6ancillary['AnsilEri] a.补助的, 副的 L4angular ['A^julE] adj. 有角的 L20annealing[E'li:liN] n.退火 L2aperture ['ApEtFE] n.孔 L17applied loads 作用力 L1appropriate [E'prEuprieit] a. 适当的 L6,20arc[a:k] n.弧, 弓形 L10arise[E'raiz] vi. 出现, 发生 L21arrange[E'reidV] v. 安排 L12article['a:tikl] n.制品, 产品 L21ascertain[7AsE'tein] vt. 确定, 查明 L1assemble[E'sembl] vt.组装 L4attitude ['Atitju:d] n 态度 L17auxiliary [C:^'ziljEri]adj. 辅助的 L8avoid[E'vCid] v.避免 L7axis['Aksis] n.轴 L5axle['Aksl] n.轮轴, 车轴 L1Bbackup['bAk7Qp] n. 备份 L9batch [bAtF] n 一批 L17bearing['bZEriN] n.轴承,支座 L21bed[bed] n. 床身 L5behavior[bi'heivjE] n. 性能 L1bench-work 钳工工作 L4bend[bend] v.弯曲 L1beneath[bi'ni:W] prep在···下 L4bin [bin] n. 仓，料架 L19blank [blANk] n. 坯料 L20blank [blANk] v. 冲裁,落料 L17blanking tool 落料模 L17blast [blQst] n.一阵（风） L18blemish['blemiF] n. 缺点, 污点 L13bolster['bEulstE] n. 模座,垫板 L4,5boost[bu:st] n. 推进 L9boring['bC:riN] n.镗削, 镗孔 L4,5bracket ['brAkit] n. 支架 L19brass [brAs] n.黄铜 L2break down 破坏 L1breakage ['breikidV] n.破坏 L17bridge piece L16brine[brain] n. 盐水 L2brittle['britl] adv.易碎的 L1buffer [bQfE] n.缓冲器 L8built-in 内装的 L9bulging [bQldViN] n. 凸肚 L22burr [bE:] n. 毛刺 L17bush [buF] n. 衬套 L17bush[buF]n. 衬套 L5by far (修饰比较级, 最高级)···得多, 最 L3 by means of 借助于 L5Ccabinet ['kAbinit] n.橱柜 L7call upon 要求 L17carbide['ka:baid] n.碳化物 L10carburzing['ka:bjuretiN] n. 渗碳 L2carriage['kAridV] n.拖板, 大拖板 L5carry along 一起带走 L18carry down over 从···上取下 L21carry out 完成 L17case hardening 表面硬化 L2case[keis] n. 壳, 套 L2cast steel 铸钢 L17casting['ka:stiN] n. 铸造,铸件 L3category['kAtE^Euri] n. 种类 L6,15caution ['kC:FEn] n. 警告，警示 L17cavity and core plates 凹模和凸模板 L11cavity['kAviti] n.型腔, 腔, 洞 L4,10centre-drilling 中心孔 L5ceramic[si'rAmik] n.陶瓷制品 L3chain doted line 点划线 L11channel['tFAnl] n.通道, 信道 L8characteristic[kArEktE'ristik] n.特性 L1check[tFek] v.核算 L21chip[tFip] n.切屑, 铁屑 L3chuck [tFQk] n.卡盘 L5,8chute [Fu:t] n. 斜道 L19circa ['sEkE:] adv. 大约 L7circlip['sE:klip] n.(开口)簧环 L22circuit['sE:kit] n. 回路, 环路 L13circular supoport block L5circulate['sE:kjuleid] v.(使)循环 L13clamp [klAmp] vt 夹紧 L17clamp[klAmp] n.压板 L12clay[klei] n. 泥土 L2,7clearance ['kliErEns] n. 间隙 L17clip [klip] vt. 切断，夹住 L19cold hobbing 冷挤压 L4cold slug well 冷料井 L12collapse[kE'lAps] vi.崩塌, 瓦解 L22collapsible[kE'lApsEbl] adj.可分解的 L22 combination [kCmbi'neiFEn] n. 组合 L18 commence[kE'mens] v. 开始, 着手 L16 commence[kE'mens]v. 开始 L21commercial [kE'mE:FEl] adj. 商业的 L7 competitive[kEm'petitiv] a. 竞争的 L9 complementary[7kCmpli'mentEri] a. 互补的 L5 complexity [kem'pleksiti] n.复杂性 L8 complicated['kCmplEkeitid] adj.复杂的 L2 complication [kCmpli'keiFEn] n. 复杂化 L5,20 compression [kEm'preFEn] n.压缩 L1comprise[kEm'prais] vt.包含 L16compromise['kCmprEmaiz] n. 妥协, 折衷 L13 concern with 关于 L6concise[kEn'sais] a. 简明的, 简练的 L9 confront[kEn'frQnt] vt. 使面临 L14connector[kE'nektE] n. 连接口, 接头 L14consequent['kCnsikwEnt] a. 随之发生的, 必然的 L3 console ['kCnsoul] n.控制台 L8consume [kEn'sjum] vt. 消耗, 占用 L7 consummate [kEn'sQmeit] vt. 使完善 L6container[kEn'teinE] n. 容器 L11contingent[ken'tindVEnt] a.可能发生的 L9contour['kEntuE] n.轮廓 L5,21conventional[kEn'venFEnl] a. 常规的 L4converge[kEn'vE:dV] v.集中于一点 L21conversant[kCn'vE:sEnt] a. 熟悉的 L15conversion[kEn'vE:FEn] n 换算, 转换 L7conveyer[ken'veiE] n. 运送装置 L12coolant['ku:lEnt] n. 冷却液 L13coordinate [kEu'C:dnit] vt. (使)协调 L8copy machine 仿形(加工)机床 L4core[kC:] n. 型芯, 核心 L2,4corresponding [ka:ri'spCdiN] n.相应的 L7 counteract [kauntE'rAkt] vt. 反作用,抵抗 L20 couple with 伴随 L20CPU (central processing unit) 中央处理器 L9 crack[krAk ] v.（使）破裂，裂纹 L1,17critical['kritikl] adj.临界的 L2cross-hatching 剖面线 L16cross-section drawn 剖面图 L11cross-slide 横向滑板 L5CRT (cathoder-ray tube) 阴极射线管 L9crush[krQF]vt.压碎 L1cryogenic[7kraiE'dVenik ]a.低温学的 L1crystal['kristl] adj.结晶状的 L1cubic['kju:bik] a. 立方的, 立方体的 L3cup [kQp] vt (使)成杯状, 引伸 L18curable ['kjurEbl] adj. 可矫正的 L20curvature['kE:vEtFE] n.弧线 L21curve [kE:v] vt. 使弯曲 L20cutter bit 刀头, 刀片 L3cyanide['saiEnaid] n.氰化物 L2Ddash [dAF] n. 破折号 L6daylight ['deilait] n. 板距 L12decline[di'klain] v.下落,下降,减少, L3,9deform[di'fC:m] v. (使)变形 L1,3demonstrate['demEstreit ] v证明 L21depict[di'pikt ] vt 描述 L18deposite [di'pCzit] vt. 放置 L20depression[di'preFEn] n. 凹穴 L12descend [di'sent] v. 下降 L20desirable[di'zairEbl] a. 合适的 L2detail ['diteil] n.细节，详情 L17deterioration[ditiEri:E'reiFEn] n. 退化, 恶化 L12 determine[di'tE:min] v.决定 L16diagrammmatic[7daiEgrE'mAtik].a.图解的，图表的 L10 dictate['dikteit] v. 支配 L12die[dai] n.模具, 冲模, 凹模 L2dielectric[daii'lektrik] n. 电介质 L10die-set 模架 L19digital ['didVitl ] n.数字式数字, a.数字的 L3,6 dimensional[dddi'menFEnl] a. 尺寸的, 空间的 L3 discharge[dis'tFa:dV] n.v. 放电, 卸下, 排出 L3 discharge[dis'tFa:dV] v.卸下 L8discrete [dis'cri:t] adj. 离散的,分立的 L7 dislodge[dis'lCdV] v. 拉出, 取出 L12dissolution[disE'lu:FEn] n.结束 L9distinct [dis'tiNkt] a.不同的，显著的 L6distort [dis'dC:t] vt. 扭曲 L20distort[dis'tC:t] vt. (使)变形, 扭曲 L1distributed system 分布式系统 L9dowel ['dauEl] n. 销子 L19dramaticlly [drE'mAtikli] adv. 显著地 L7drastic ['drAstik] a.激烈的 L17draughting[dra:ftiN] n. 绘图 L16draughtsman['drAftsmEn] n. 起草人 L16drawing['drC:iN] n. 制图 L11drill press 钻床 L8drum [drQm] n.鼓轮 L8dual ['dju:El] adv. 双的，双重的 L18ductility [dQk'tiliti ] n.延展性 L1,21dynamic [dai'nAmik ] adj 动力的 L6Eedge [edV] n .边缘 L20e.g.(exempli gratia) [拉] 例如 L12ejector [i'dVektE] n.排出器， L18ejector plate 顶出板 L16ejector rob 顶杆 L5elasticity[ilA'stisiti] n.弹性 L1electric dicharge machining 电火花加工L3electrical discharge machining电火花加工 L10electrochemical machining 电化学加工L3electrode[i'lektrEud] n. 电极 L10electro-deposition 电铸 L4elementary [elE'mentEri] adj.基本的 L2eliminate[i'limineit] vt. 消除, 除去 L10elongate[i'lCN^et] vt. (使)伸长, 延长 L1 emerge [i'mE:dV] vi. 形成, 显现 L20 emphasise['emfEsaiz] vt. 强调 L4endeavour[en'devE] n. 尽力 L17engagement[in'^eidVment] n. 约束, 接合 L22 enhance[in'hAns] vt. 提高, 增强 L9ensure [in'FuE] vt. 确保，保证 L17envisage[in'vizidV] vt.设想 L15erase[i'reis] vt. 抹去, 擦掉 L16evaluation[i'vAlju7eiFEn] n. 评价, 估价L1 eventually[i'vEntFuEli ] adv.终于 L21 evolution[evE'lu:FEn] n.进展 L16excecution[eksi'kju:FEn] n. 执行, 完成 L9 execute ['ekskju:t] v. 执行 L8exerte [i^'zE:t] vt. 施加 L20experience[iks'piriEns] n. 经验 L16 explosive[iks'plEusiv]adj.爆炸(性)的 L22 extend[eks'tend] v. 伸展 L2external[eks'tE:nl] a. 外部的 L5,11 extract[eks'trAkt] v. 拔出 L14extreme[iks'tri:m] n. 极端 L13extremely[iks'tri:mli] adv. 非常地 L12 extremity[iks'tmiti] n. 极端 L13extrusion[eks'tru:VEn] n. 挤压, 挤出 L3FF (Fahrenheit)['fArEnhait]n.华氏温度 L2fabricate ['fAbrikeit] vt.制作,制造 L7 facilitate [fE'siliteit] vt. 帮助 L6facility[fE'siliti] n. 设备 L4facing[feisiN] n. 端面车削 L5fall within 属于, 适合于 L15fan[fAn] n.风扇 L7far from 毫不, 一点不, 远非 L9fatigue[fE'ti^] n.疲劳 L1feasible ['fi:zEbl] a 可行的 L18feature ['fi:tFE] n.特色, 特征 L7,17feed[fi:d] n.. 进给 L5feedback ['fi:dbAk] n. 反馈 L8female['fi:meil] a. 阴的, 凹形的 L11ferrule['ferEl] n. 套管 L14file system 文件系统 L9fitter['fitE] n.装配工, 钳工 L4fix[fiks] vt. 使固定, 安装, vi. 固定 L11 fixed half and moving half 定模和动模 L11 flat-panel technology 平面(显示)技术 L9flexibility[fleksi'biliti] n. 适应性, 柔性 L9 flexible['fleksEbl] a. 柔韧的 L13flow mark 流动斑点 L13follow-on tool 连续模 L18foregoing ['fC:'^EuiN]adj. 在前的,前面的L8foretell[fC:'tell] vt. 预测, 预示, 预言 L9 forge[fC:dV] n. v. 锻造 L3forming[fC:miN] n. 成型 L3four screen quadrants 四屏幕象限 L9fracture['frAktFE] n.破裂 L21free from 免于 L21Ggap[^Ap] n. 裂口, 间隙 L10gearbox['^iEbCks] n.齿轮箱 L5general arrangement L16govern['^QvEn] v.统治, 支配, 管理 L13grain [^rein] n. 纹理 L20graphic ['^rAfik] adj. 图解的 L6grasp [^rAsp] vt. 抓住 L8grid[^rid] n. 格子, 网格 L16grind[^raind] v. 磨, 磨削, 研磨 L3grinding ['^raindiN] n. 磨光,磨削 L3,20 grinding machine 磨床 L5gripper[^ripE] n. 抓爪, 夹具 L9groove[^ru:v] n. 凹槽 L12guide bush 导套 L5guide pillar 导柱 L5guide pillars and bushes 导柱和导套 L11Hhandset['hAndset] n. 电话听筒 L4hardness['ha:dnis] n.硬度 L1,2hardware ['ha:dwZE] n. 硬件 L6headstock['hedstCk] n.床头箱, 主轴箱 L5 hexagonal[hek'sA^Enl] a. 六角形的, 六角的 L11 hindrance['hindrEns] n.障碍, 障碍物 L11hob[hCb] n. 滚刀, 冲头 L4hollow-ware 空心件 L21horizontal[hCri'zCntl] a. 水平的 L16hose[hEuz] n. 软管, 水管 L13hyperbolic [haipE'bClik] adj.双曲线的 L7Ii.e. (id est) [拉] 也就是 L12identical[ai'dentikl] a同样的 L16identify [ai'dentifai] v. 确定, 识别 L7idle ['aidl] adj.空闲的 L8immediately[i'mi:djEtli] adv. 正好, 恰好 L12impact['impAkt] n.冲击 L1impart [im'pa:t] v.给予 L11,17implement ['implimEnt] vt 实现 L6impossibility[impCsE'biliti] n.不可能 L21impression[im'preFEn] n. 型腔 L11in contact with 接触 L1in terms of 依据 L1inasmuch (as)[inEz'mQtF] conj.因为, 由于L3inch-to-metric conversions 英公制转换 L7 inclinable [in'klainEbl] adj. 可倾斜的 L20inclusion [in'kluFEn] n. 内含物 L19inconspicuous[inkEn'spikjuEs] a. 不显眼的 L14 incorporate [in'kC:pEreit] v 合并,混合L17 indentation[7inden'teiFEn ] n.压痕 L1indenter[in'dentE] n. 压头 L1independently[indi'peinEntli] a. 独自地, 独立地 L16 inevitably[in'evitEbli] ad. 不可避免地 L14 inexpensive[inik'spensiv]adj. 便宜的 L2inherently [in'hiErEntli] adv.固有的 L7injection mould 注塑模 L11injection[in'dVekFEn] n. 注射 L11in-line-of-draw 直接脱模 L14insert[in'sE:t] n. 嵌件 L16inserted die 嵌入式凹模 L19inspection[in'spekFEn] n.检查,监督 L9installation[instE'leiFEn] n. 安装 L10integration [inti'^reiFEn] n.集成 L6intelligent[in'telidVEnt]a. 智能的 L9intentinonally [in'tenFEnEli] adv 加强地，集中地 L17 interface ['intEfeis] n.. 界面 L6internal[in'tE:nl] a. 内部的 L1,5interpolation [intEpE'leiFEn] n.插值法 L7 investment casting 熔模铸造 L4irregular [i'regjulE] adj. 不规则的，无规律 L17 irrespective of 不论, 不管 L11irrespective[iri'spektiv] a. 不顾的, 不考虑的 L11 issue ['isju] vt. 发布，发出 L6Jjoint line 结合线 L14Kkerosene['kerEsi:n] n.煤油 L10keyboard ['ki:bC:d ] n. 健盘 L6knock [nRk] v 敲，敲打 L17Llance [la:ns] v. 切缝 L19lathe[leiT] n. 车床 L4latitude ['lAtitju:d] n. 自由 L17lay out 布置 L13limitation[limi'teiFEn] n.限度,限制,局限(性) L3local intelligence局部智能 L9locate [lEu'keit] vt. 定位 L18logic ['lCdVik] n. 逻辑 L7longitudinal['lCndVE'tju:dinl] a. 纵向的 L5longitudinally['lCndVE'tju:dinl] a. 纵向的 L13look upon 视作, 看待 L17lubrication[lju:bri'keiFEn ] n.润滑 L21Mmachine shop 车间 L2machine table 工作台 L8machining[mE'Fi:niN] n. 加工 L3made-to-measure 定做 L15maintenance['meintinEns] n.维护,维修 L7majority[mE'dVa:riti] n.多数 L21make use of 利用 L2male[meil] a. 阳的, 凸形的 L11malfunction['mAl'fQNFEn] n. 故障 L9mandrel['mAdtil] n.心轴 L22manifestation[mAnifEs'teiFEn] n. 表现, 显示 L9massiveness ['mAsivnis ] 厚实，大块 L19measure['meVE] n. 大小, 度量 L1microcomputer 微型计算机 L9microns['maikrCn] n.微米 L10microprocessor 微处理器 L9mild steel 低碳钢 L17milling machine 铣床 L4mineral['minErEl] n.矿物, 矿产 L2minimise['minimaiz] v.把···减到最少, 最小化 L13minute['minit] a.微小的 L10mirror image 镜像 L16mirror['mirE] n. 镜子 L16MIT (Massachusetts Institute of Technology) 麻省理工学院 L7 moderate['mCdErit]adj. 适度的 L1,2modification [mRdifi'keiFEn ] n. 修改, 修正 L6modulus['mCdjulEs] n.系数 L1mold[mEuld] n. 模, 铸模, v. 制模, 造型 L3monitor ['mCnitE ] v. 监控 L6monograph['mCnE^ra:f] n. 专著 L4more often than not 常常 L20motivation[mEuti'veiFEn] n. 动机 L9mould split line 模具分型线 L12moulding['mEudiN] n. 注塑件 L5,11move away from 抛弃 L17multi-imprssion mould 多型腔模 L12Nnarrow['nArEu] a. 狭窄的 L12NC (numerical control ) 数控 L7nevertheless[7nevETE'les] conj.,adv.然而,不过 L11 nonferrous['nCn'ferEs] adj.不含铁的, 非铁的 L2 normally['nC:mli]adv.通常地 L22novice['nCvis] n. 新手, 初学者 L16nozzle['nCzl] n. 喷嘴, 注口 L12numerical [nju'merikl] n. 数字的 L6Oobjectionable [Eb'dVekFEbl] adj. 有异议的，讨厌的 L17 observe[Eb'zE:v] vt. 观察 L2obviously ['CbviEsli] adv 明显地 L17off-line 脱机的 L6on-line 联机 L9operational [CpE'reiFEnl] adj.操作的, 运作的 L8 opportunity[CpE'tju:niti] n. 时机, 机会 L13opposing[E'pEuziN] a.对立的, 对面的L12opposite['CpEzit] n. 反面 L1 a.对立的,对面的 L12 optimization [Rptimai'zeiFEn] n.最优化 L6orient ['C:riEnt] vt. 确定方向 L8orthodox ['C:WEdCks] adj. 正统的，正规的 L19overall['EuvErC:l] a.全面的,全部的 L8,13overbend v.过度弯曲 L20overcome[EuvE'kQm] vt.克服, 战胜 L10overlaping['EuvE'lApiN] n. 重叠 L4overriding[EuvE'raidiN] a. 主要的, 占优势的 L11pack[pAk] v. 包装 L2package ['pAkidV] vt.包装 L7pallet ['pAlit] n.货盘 L8panel ['pAnl] n.面板 L7paraffin['pArEfin] n. 石蜡 L10parallel[pArElel] a.平行的 L5penetration[peni'treiFEn ] n.穿透 L1peripheral [pE'rifErEl] adj 外围的 L6periphery [pE'rifEri] n. 外围 L18permit[pE'mit] v. 许可, 允许 L16pessure casting 压力铸造 L4pillar['pilE] n. 柱子, 导柱 L5,17pin[pin] n. 销, 栓, 钉 L5,17pin-point gate 针点式浇口 L12piston ['pistEn] n.活塞 L1plan view 主视图 L16plasma['plAzmE] n. 等离子 L9plastic['plAstik] n. 塑料 L3platen['plAtEn] n. 压板 L12plotter[plCtE] n. 绘图机 L9plunge [plQndV] v翻孔 L18plunge[plQndV] v.投入 L2plunger ['plQndVE ] n. 柱塞 L19pocket-size 袖珍 L9portray[pC:'trei] v.描绘 L21pot[pCt] n.壶 L21pour[pC:] vt. 灌, 注 L22practicable['prAktikEb] a. 行得通的 L14 preferable['prefErEbl] a.更好的, 更可取的 L3 preliminary [pri'liminEri] adj 初步的，预备的 L19 press setter 装模工 L17press[pres] n.压,压床,冲床,压力机 L2,8prevent [pri'vent] v. 妨碍 L20primarily['praimErili] adv.主要地 L4procedure[prE'si:dVE] n.步骤, 方法, 程序 L2,16 productivity.[prEudQk'tiviti] n. 生产力 L9profile ['prEufail] n.轮廓 L10progressively[prE'^resiv] ad.渐进地 L15project[prE'dVekt] n.项目 L2project[prE'dVekt] v. 凸出 L11projection[prE'dVekFEn] n.突出部分 L21proper['prCpE] a. 本身的 L10property['prCpEti] n.特性 L1prototype ['prEutEtaip] n. 原形 L7proximity[prCk'simiti] n.接近 L9prudent['pru:dEnt] a. 谨慎的 L16punch [pQntF] v. 冲孔 L3punch shapper tool 刨模机 L17punch-cum-blanking die 凹凸模 L18punched tape 穿孔带 L3purchase ['pE:tFEs] vt. 买，购买 L6push back pin 回程杆 L5pyrometer[pai'nCmitE] n. 高温计 L2Qquality['kwaliti] n. 质量 L1,3quandrant['kwCdrEnt] n. 象限 L9quantity ['kwCntiti] n. 量，数量 L17quench[kwentF] vt. 淬火 L2Rradial['reidiEl] adv.放射状的 L22ram [rAm] n 撞锤. L17rapid['rApid]adj. 迅速的 L2rapidly['rApidli]adv. 迅速地 L1raster['rAstE] n. 光栅 L9raw [rC:] adj. 未加工的 L6raw material 原材料 L3ream [ri:m] v 铰大 L17reaming[ri:miN] n. 扩孔, 铰孔 L8recall[ri'kC:l] vt. 记起, 想起 L13recede [ri'si:d] v. 收回, 后退 L20recess [ri'ses] n. 凹槽,凹座,凹进处 L4,18redundancy[ri'dQndEnsi] n. 过多 L9re-entrant 凹入的 L12refer[ri'fE:] v. 指, 涉及, 谈及 L1,12reference['refErEns] n.参照,参考 L21refresh display 刷新显示 L9register ring 定位环 L11register['redVstE] v. 记录, 显示, 记数 L2regrind[ri:'^aind](reground[ri:'gru:nd]) vt. 再磨研 L12 relative['relEtiv] a. 相当的, 比较的 L12relay ['ri:lei] n. 继电器 L7release[ri'li:s] vt. 释放 L1relegate['relE7geit] vt. 把··降低到 L9reliability [rilaiE'biliti] n. 可靠性 L7relief valves 安全阀 L22relief[ri'li:f] n.解除 L22relieve[ri'li:v ]vt.减轻, 解除 L2remainder[ri'meindE] n. 剩余物, 其余部分 L4removal[ri'mu:vl] n. 取出 L14remove[ri'mu:v] v. 切除, 切削 L4reposition [ripE'ziFEn] n.重新安排 L17represent[7repri'zentE] v 代表,象征 L11reputable['repjutEbl] a. 有名的, 受尊敬的 L15reservoir['rezEvwa: ] n.容器, 储存器 L22resident['rezidEnt] a. 驻存的 L9resist[ri'zist] vt.抵抗 L1resistance[ri'zistEns] n.阻力, 抵抗 L1resolution[7rezE'lu:FEn] n. 分辨率 L9respective[ri'spektiv] a.分别的,各自的 L11respond[ris'pCnd] v.响应, 作出反应 L9responsibility[rispCnsE'biliti] n.责任 L13restrain[ris'trein]v.抑制 L21restrict [ris'trikt] vt 限制，限定 L18restriction[ris'trikFEn] n. 限制 L12retain[ri'tein] vt.保持, 保留 L2,12retaining plate 顶出固定板 L16reveal [ri'vil] vt.显示，展现 L17reversal [ri'vEsl] n. 反向 L1,20right-angled 成直角的 L20rigidity[ri'dViditi] n. 刚度 L1rod[rCd] n. 杆, 棒 L1,5rotate['rEuteit] vt.(使)旋转 L5rough machining 粗加工 L5rough[rQf] a. 粗略的 L5,21routine [ru:'ti:n] n. 程序 L7rubber['rQbE] n.橡胶 L3,22runner and gate systems 流道和浇口系统 L11Ssand casting 砂型铸造 L3satisfactorily[7sAtis'fAktrili] adv. 满意地 L1 saw[aC:] n. 锯子 L4scale[skeil]n. 硬壳 L2score[skC:] v. 刻划 L14scrap[skrAp] n.废料, 边角料, 切屑 L2,3 screwcutting 切螺纹 L4seal[si:l] vt.密封 L22secondary storage L9section cutting plane 剖切面 L16secure[si'kjuE] v.固定 L22secure[si'kjuE] vt.紧固,夹紧,固定 L5,22 segment['se^mEnt] v. 分割 L10sensitive['sensitiv]a.敏感的 L1,7sequence ['si:kwEns] n. 次序 L6sequential[si'kwenFEl] a.相继的 L16seriously['siEriEsli] adv.严重地 L1 servomechanism ['sE:vE'mekEnizm] n.伺服机构 L7 Servomechanism Laboratoies 伺服机构实验室 L7 servomotor ['sE:vEmEutE] n.伺服马达 L8setter ['setE] n 安装者 L17set-up 机构 L20sever ['sevE] v 切断 L17severity [si'veriti] n. 严重 L20shaded[FAdid] adj.阴影的 L21shank [FANk] n. 柄. L17shear[FiE]n.剪,切 L1shot[FCt] n. 注射 L12shrink[FriNk] vi. 收缩 L11side sectional view 侧视图 L16signal ['si^nl] n.信号 L8similarity[simi'lAriti] n.类似 L15simplicity[sim'plisiti] n. 简单 L12single-point cutting tool 单刃刀具 L5situate['sitjueit] vt. 使位于, 使处于 L11slide [slaid] vi. 滑动, 滑落 L20slideway['slaidwei] n. 导轨 L5slot[slCt] n. 槽 L4slug[slQ^] n. 嵌条 L12soak[sEuk] v. 浸, 泡, 均热 L2software ['sCftwZE] n. 软件 L6solid['sClid] n.立体, 固体 L9solidify[sE'lidifai] vt.vi. (使)凝固, (使)固化 L13 solution[sE'lu:FEn] n.溶液 L2sophisiticated [sE'fistikeitid] adj.尖端的,完善的 L8 sound[saund] a. 结实的, 坚固的) L1spark erosion 火花蚀刻 L10spindle['spindl] n. 主轴 L5,8spline[splain] n.花键 L4split[split] n. 侧向分型, 分型 L12,14spool[spu:l] n. 线轴 L14springback n.反弹 L20spring-loaded 装弹簧的 L18sprue bush 主流道衬套 L11sprue puller 浇道拉杆 L12square[skwZE] v. 使成方形 L4stage [steidV] n. 阶段 L16,19standardisation[7stAndEdai'zeiFEn] n. 标准化 L15 startling['sta:tliN] a. 令人吃惊的 L10steadily['stedEli ] adv. 稳定地 L21step-by-step 逐步 L8stickiness['stikinis] n.粘性 L22stiffness['stifnis] n. 刚度 L1stock[stCk] n.毛坯, 坯料 L3storage tube display 储存管显示 L9storage['stC:ridV] n. 储存器 L9straightforward[streit'fC:wEd]a.直接的 L10strain[strein] n.应变 L1strength[streNW] n.强度 L1stress[stres] n.压力,应力 L1stress-strain应力--应变 L6stretch[stretF] v.伸展 L1,21strike [straik] vt. 冲击 L20stringent['strindVEnt ] a.严厉的 L22stripper[stripE] n. 推板 L15stroke[strouk] n. 冲程, 行程 L12structrural build-up 结构上形成的 L11sub-base 垫板 L19subject['sQbdVikt] vt.使受到 L21submerge[sEb'mE:dV] v.淹没 L22subsequent ['sQbsikwent] adj. 后来的 L20subsequently ['sQbsikwentli] adv. 后来, 随后 L5substantial[sEb'stAnFEl] a. 实质的 L10substitute ['sQbstitju:t] vt. 代替,.替换 L7subtract[sEb'trAkt] v.减, 减去 L15suitable['su:tEbl] a. 合适的, 适当的 L5suitably['su:tEbli] ad.合适地 L15sunk[sQNk](sink的过去分词) v. 下沉, 下陷 L11superior[sE'piEriE] adj.上好的 L22susceptible[sE'septEbl] adj.易受影响的 L7sweep away 扫过 L17symmetrical[si'metrikl] a. 对称的 L14synchronize ['siNkrEnaiz] v.同步,同时发生L8Ttactile['tAktail] a. 触觉的, 有触觉的 L9tailstock['teilstCk] n.尾架 L5tapered['teipEd] a. 锥形的 L12tapping['tApiN] n. 攻丝 L8technique[tek'ni:k] n. 技术 L16tempering['tempErN] n.回火 L2tendency['tendEnsi] n. 趋向, 倾向 L13tensile['tensail] a.拉力的, 可拉伸的 L2 拉紧的, 张紧的 L1tension ['tenFEn] n.拉紧,张紧 L1terminal ['tE:mEnl ] n. 终端机 L6terminology[tE:mi'nClEdVi ] n. 术语, 用辞 L11theoretically [Wi:E'retikli ] adv.理论地 L21thereby['TZEbai] ad. 因此, 从而 L15thermoplastic['WE:mEu'plAstik] a. 热塑性的, n. 热塑性塑料 L3 thermoset['WE:mEset] n.热固性 L12thoroughly['WQrEuli] adv.十分地, 彻底地 L2thread pitch 螺距 L5thread[Wred] n. 螺纹 L5thrown up 推上 L17tilt [tilt] n. 倾斜, 翘起 L20tolerance ['tClErEns] n..公差 L17tong[tCN] n. 火钳 L2tonnage['tQnidV] n.吨位, 总吨数 L3tool point 刀锋 L3tool room 工具车间 L10toolholder['tu:lhEuldE] n.刀夹,工具柄 L5toolmaker ['tu:l'meikE] n 模具制造者 L17toolpost grinder 工具磨床 L4toolpost['tu:l'pEust] n. 刀架 L4torsional ['tC:FEnl] a扭转的 . L1toughness['tCfnis] n. 韧性 L2trace [treis] vt.追踪 L7tracer-controlled milling machine 仿形铣床 L4 transverse[trAns'vE:s] a. 横向的 L5tray [trei] n. 盘，盘子，蝶 L19treatment['tri:tmEnt] n.处理 L2tremendous[tri'mendEs] a. 惊人的, 巨大的 L9 trend [trend] n.趋势 L7trigger stop 始用挡料销 L17tungsten['tQNstEn] n.钨 L10turning['tE:niN] n.车削 L4,5twist[twist ] v.扭曲，扭转 L1two-plate mould 双板式注射模 L12Uultimately['Qltimitli] adv终于. L6undercut moulding 侧向分型模 L14undercut['QndEkQt] n. 侧向分型 L14undercut['QndEkQt] n.底切 L12underfeed['QndE'fi:d] a, 底部进料的 L15undergo[QndE'^Eu] vt.经受 L1underside['QndEsaid] n 下面,下侧 L11undue[Qn'dju:] a.不适当的, 过度的 L4,10uniform['ju:nifC:m] a.统一的, 一致的 L12utilize ['ju:tilaiz] v 利用 L17Utopian[ju'tEupiEn] adj.乌托邦的, 理想化的 L21Vvalve[vAlv] n.阀 L22vaporize['veipEraiz] vt.vi. 汽化, (使)蒸发 L10 variation [vZEri'eiFEn] n. 变化 L20various ['vZEriEs] a.不同的,各种的 L1,20vector feedrate computation 向量进刀速率计算 L7 vee [vi:] n. v字形 L20velocity[vi'lCsiti] n.速度 L1versatile['vEsEtail] a.多才多艺的,万用的 L5,8 vertical['vE:tikl] a. 垂直的 L16via [vaiE] prep.经,通过 L8vicinity[vE'siniti] n.附近 L13viewpoint['vju:pCint] n. 观点 L4Wwander['wCndE] v. 偏离方向 L13warp[wC:p] v. 翘曲 L2washer ['wCFE] n. 垫圈 L18wear [wZE] v.磨损 L7well line 结合线 L13whereupon [hwZErE'pCn] adv. 于是 L19winding ['waindiN] n. 绕, 卷 L8with respect to 相对于 L1,5withstand[wiT'stAnd] vt.经受,经得起 L1work[wE:k] n. 工件 L4workstage 工序 L19wrinkle['riNkl] n.皱纹vt.使皱 L21Yyield[ji:ld] v. 生产 L9Zzoom[zu:] n. 图象电子放大 L9GLOSSARYAabrasive grinding 强力磨削 L3abrasive[E'breisiv] a.磨料的, 研磨的 L2,3absence ['AbsEns] n.. 不在，缺席 L17accesssory[Ak'sesEri] n.附件 L10accommodate[E'kCmEdeit] v. 适应 L5accordingly[E'kC:diNli] adv.因此,从而,相应地 L7,13 accuracy['AkjurEsi] n精度,准确性 L1,3actuate['Aktjueit] vt.开动(机器), 驱动 L8adequate['Adikwit] a. 足够的 L13adhesive[Ed'hi:siv] n. 粘合剂 L22adjacent[E'dVeisnt] a. 邻近的 L13adopt[E'dCpt] vt. 采用 L4advance [Ed'vA:ns] n.进步 L7advisable [Ed'vaizbl] adj. 可取的 L20agitate['AdViteit] v. 摇动 L2a large extent 很大程度 L4,13algorithm ['Al^EriTEm] n. 算法 L6align [E'lain] v 定位，调准 L17alignment[E'lainmEnt] n. 校直 L11all-too-frequent 频繁 L17allowance[E'lEuens] n. 容差, 余量 L5alternate['C:ltEnit]v.交替,轮流 L1alternative[C:l'tE:nEtiv] n. 替换物 L3alternatively[C:l'tE:nEtivli] ad. 做为选择, 也许 L5 aluminiun[7Alju'minjEm] n.铝 L2ample['Ampl] adj. 充足的 L20analysis [E'nAlEsis] n. 分析 L6ancillary['AnsilEri] a.补助的, 副的 L4angular ['A^julE] adj. 有角的 L20annealing[E'li:liN] n.退火 L2aperture ['ApEtFE] n.孔 L17applied loads 作用力 L1appropriate [E'prEuprieit] a. 适当的 L6,20arc[a:k] n.弧, 弓形 L10arise[E'raiz] vi. 出现, 发生 L21arrange[E'reidV] v. 安排 L12article['a:tikl] n.制品, 产品 L21ascertain[7AsE'tein] vt. 确定, 查明 L1 assemble[E'sembl] vt.组装 L4attitude ['Atitju:d] n 态度 L17auxiliary [C:^'ziljEri]adj. 辅助的 L8avoid[E'vCid] v.避免 L7axis['Aksis] n.轴 L5axle['Aksl] n.轮轴, 车轴 L1Bbackup['bAk7Qp] n. 备份 L9batch [bAtF] n 一批 L17bearing['bZEriN] n.轴承,支座 L21bed[bed] n. 床身 L5behavior[bi'heivjE] n. 性能 L1bench-work 钳工工作 L4bend[bend] v.弯曲 L1beneath[bi'ni:W] prep在···下 L4bin [bin] n. 仓，料架 L19blank [blANk] n. 坯料 L20blank [blANk] v. 冲裁,落料 L17blanking tool 落料模 L17blast [blQst] n.一阵（风） L18blemish['blemiF] n. 缺点, 污点 L13bolster['bEulstE] n. 模座,垫板 L4,5boost[bu:st] n. 推进 L9boring['bC:riN] n.镗削, 镗孔 L4,5bracket ['brAkit] n. 支架 L19brass [brAs] n.黄铜 L2break down 破坏 L1breakage ['breikidV] n.破坏 L17bridge piece L16brine[brain] n. 盐水 L2brittle['britl] adv.易碎的 L1buffer [bQfE] n.缓冲器 L8built-in 内装的 L9bulging [bQldViN] n. 凸肚 L22burr [bE:] n. 毛刺 L17bush [buF] n. 衬套 L17bush[buF]n. 衬套 L5by far (修饰比较级, 最高级)···得多, 最 L3 by means of 借助于 L5Ccabinet ['kAbinit] n.橱柜 L7call upon 要求 L17carbide['ka:baid] n.碳化物 L10carburzing['ka:bjuretiN] n. 渗碳 L2 carriage['kAridV] n.拖板, 大拖板 L5carry along 一起带走 L18carry down over 从···上取下 L21carry out 完成 L17case hardening 表面硬化 L2case[keis] n. 壳, 套 L2cast steel 铸钢 L17casting['ka:stiN] n. 铸造,铸件 L3category['kAtE^Euri] n. 种类 L6,15caution ['kC:FEn] n. 警告，警示 L17cavity and core plates 凹模和凸模板 L11 cavity['kAviti] n.型腔, 腔, 洞 L4,10 centre-drilling 中心孔 L5ceramic[si'rAmik] n.陶瓷制品 L3chain doted line 点划线 L11channel['tFAnl] n.通道, 信道 L8 characteristic[kArEktE'ristik] n.特性 L1 check[tFek] v.核算 L21chip[tFip] n.切屑, 铁屑 L3chuck [tFQk] n.卡盘 L5,8chute [Fu:t] n. 斜道 L19circa ['sEkE:] adv. 大约 L7circlip['sE:klip] n.(开口)簧环 L22circuit['sE:kit] n. 回路, 环路 L13circular supoport block L5circulate['sE:kjuleid] v.(使)循环 L13clamp [klAmp] vt 夹紧 L17clamp[klAmp] n.压板 L12clay[klei] n. 泥土 L2,7clearance ['kliErEns] n. 间隙 L17clip [klip] vt. 切断，夹住 L19cold hobbing 冷挤压 L4cold slug well 冷料井 L12collapse[kE'lAps] vi.崩塌, 瓦解 L22 collapsible[kE'lApsEbl] adj.可分解的 L22 combination [kCmbi'neiFEn] n. 组合 L18 commence[kE'mens] v. 开始, 着手 L16 commence[kE'mens]v. 开始 L21commercial [kE'mE:FEl] adj. 商业的 L7 competitive[kEm'petitiv] a. 竞争的 L9 complementary[7kCmpli'mentEri] a. 互补的 L5 complexity [kem'pleksiti] n.复杂性 L8。
模具专业英语词汇
Here is a list of mold-related vocabulary in English:1. Mold -模具2. Mold cavity -模腔3. Mold core -模芯4. Mold base -模座5. Injection molding -注塑成型6. Blow molding -吹塑成型7. Compression molding -压缩成型8. Extrusion molding -挤出成型9. Rotational molding -旋转成型10. Thermoforming -热成型11. Mold design -模具设计12. Mold manufacturing -模具制造13. Mold making -模具加工14. Mold material -模具材料15. Mold steel -模具钢16. Mold release agent -脱模剂17. Mold temperature -模具温度18. Mold flow analysis -模流分析19. Mold maintenance -模具维护20. Mold repair -模具修复22. Mold polishing -模具抛光23. Molded part -注塑件24. Molded product -成型产品25. Molded surface -成型表面26. Molded feature -成型特征27. Ejector pins -顶出针28. Runner system -流道系统29. Cooling system -冷却系统30. Venting -通气31. Molded part defects -成型件缺陷32. Molded part warpage -成型件翘曲33. Molded part shrinkage -成型件收缩34. Mold release system -脱模系统35. Mold venting system -通气系统36. Mold temperature controller -模具温度控制器37. Mold gate -模具流道口38. Mold runner -模具流道39. Mold ejector system -模具顶出系统40. Mold clamping force -模具锁模力41. Mold shot size -模具射胶量42. Mold cycle time -模具循环时间44. Mold cooling time -模具冷却时间45. Mold release mechanism -模具脱模机构46. Molded part dimensions -成型件尺寸47. Molded part tolerance -成型件公差48. Molded part surface finish -成型件表面处理49. Molded part strength -成型件强度50. Molded part flexibility -成型件柔韧性51. Molded part accuracy -成型件精度52. Molded part durability -成型件耐久性53. Molded part weight -成型件重量54. Molded part texture -成型件纹理55. Molded part transparency -成型件透明度56. Molded part color -成型件颜色57. Molded part function -成型件功能58. Molded part assembly -成型件装配59. Molded part packaging -成型件包装60. Molded part labeling -成型件标记61. Molded part quality control -成型件质量控制62. Mold material selection -模具材料选择63. Mold design software -模具设计软件64. Mold manufacturing process -模具制造过程65. Mold injection molding machine -模具注塑机66. Mold blow molding machine -模具吹塑机67. Mold compression molding machine -模具压缩成型机68. Mold extrusion molding machine -模具挤出成型机69. Mold rotational molding machine -模具旋转成型机70. Mold thermoforming machine -模具热成型机71. Mold tooling -模具工装72. Molded part inspection -成型件检验73. Molded part packaging -成型件包装74. Molded part labeling -成型件标记75. Molded part storage -成型件存储76. Molded part transportation -成型件运输77. Molded part disposal -成型件处理78. Molded part recycling -成型件回收79. Molded part cost -成型件成本80. Molded part production rate -成型件生产率81. Molded part tooling cost -成型件工装成本82. Molded part tooling lead time -成型件工装交货期83. Molded part tooling lifespan -成型件工装寿命84. Molded part tooling maintenance -成型件工装维护85. Molded part tooling repair -成型件工装修复86. Molded part tooling modification -成型件工装修改87. Molded part tooling replacement -成型件工装更换88. Molded part tooling storage -成型件工装存储89. Molded part tooling transportation -成型件工装运输90. Molded part tooling disposal -成型件工装处理91. Molded part tooling recycling -成型件工装回收92. Molded part tooling cost estimation -成型件工装成本估算93. Molded part tooling design optimization -成型件工装设计优化94. Molded part tooling production planning -成型件工装生产计划95. Molded part tooling quality control -成型件工装质量控制96. Molded part tooling process improvement -成型件工装工艺改进97. Molded part tooling waste reduction -成型件工装废物减少98. Molded part tooling cost reduction -成型件工装成本降低99. Molded part tooling cycle time optimization -成型件工装循环时间优化100. Molded part tooling material selection -成型件工装材料选择101. Molded part tooling design validation -成型件工装设计验证102. Molded part tooling production monitoring -成型件工装生产监控103. Molded part tooling maintenance scheduling -成型件工装维护计划104. Molded part tooling repair process -成型件工装修复流程105. Molded part tooling modification process -成型件工装修改流程106. Molded part tooling replacement process -成型件工装更换流程107. Molded part tooling storage management -成型件工装存储管理108. Molded part tooling transportation logistics -成型件工装运输物流109. Molded part tooling disposal methods -成型件工装处理方法110. Molded part tooling recycling techniques -成型件工装回收技术111. Molded part tooling cost estimation tools -成型件工装成本估算工具112. Molded part tooling design optimization software -成型件工装设计优化软件113. Molded part tooling production planning systems -成型件工装生产计划系统114. Molded part tooling quality control methods -成型件工装质量控制方法115. Molded part tooling process improvement strategies -成型件工装工艺改进策略116. Molded part tooling waste reduction techniques -成型件工装废物减少技术117. Molded part tooling cost analysis -成型件工装成本分析118. Molded part tooling design review -成型件工装设计审查119. Molded part tooling production efficiency -成型件工装生产效率120. Molded part tooling maintenance checklist -成型件工装维护清单121. Molded part tooling repair cost estimation -成型件工装修复成本估算122. Molded part tooling modification cost estimation -成型件工装修改成本估算123. Molded part tooling replacement cost estimation -成型件工装更换成本估算124. Molded part tooling storage system -成型件工装存储系统125. Molded part tooling transportation cost calculation -成型件工装运输成本计算126. Molded part tooling disposal methods evaluation -成型件工装处理方法评估127. Molded part tooling recycling process optimization -成型件工装回收流程优化128. Molded part tooling cost reduction strategies -成型件工装成本降低策略129. Molded part tooling cycle time reduction techniques -成型件工装循环时间减少技术130. Molded part tooling material waste reduction -成型件工装材料废物减少131. Molded part tooling design validation methods -成型件工装设计验证方法132. Molded part tooling production monitoring tools -成型件工装生产监控工具133. Molded part tooling maintenance scheduling software -成型件工装维护计划软件134. Molded part tooling repair process optimization -成型件工装修复流程优化135. Molded part tooling modification process improvement -成型件工装修改流程改进136. Molded part tooling replacement process optimization -成型件工装更换流程优化137. Molded part tooling storage management techniques -成型件工装存储管理技术138. Molded part tooling transportation logistics optimization -成型件工装运输物流优化139. Molded part tooling disposal methods assessment -成型件工装处理方法评估140. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估141. Molded part tooling cost estimation software -成型件工装成本估算软件142. Molded part tooling design optimization tools -成型件工装设计优化工具143. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估144. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估145. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施146. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化147. Molded part tooling cost analysis tools -成型件工装成本分析工具148. Molded part tooling design review software -成型件工装设计审查软件149. Molded part tooling production efficiency evaluation -成型件工装生产效率评估150. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化151. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件152. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件153. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件154. Molded part tooling storage system optimization -成型件工装存储系统优化155. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件156. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具157. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术158. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施159. Molded partooling design validation methods -成型件工装设计验证方法160. Molded part tooling production monitoring tools -成型件工装生产监控工具161. Molded part tooling maintenance scheduling software -成型件工装维护计划软件162. Molded part tooling repair process optimization -成型件工装修复流程优化163. Molded part tooling modification process improvement -成型件工装修改流程改进164. Molded part tooling replacement process optimization -成型件工装更换流程优化165. Molded part tooling storage management techniques -成型件工装存储管理技术166. Molded part tooling transportation logistics optimization -成型件工装运输物流优化167. Molded part tooling disposal methods assessment -成型件工装处理方法评估168. Molded part tooling recycling techniques evaluation -成型件工装回收技术评估169. Molded part tooling cost estimation software -成型件工装成本估算软件170. Molded part tooling design optimization tools -成型件工装设计优化工具171. Molded part tooling production planning systems evaluation -成型件工装生产计划系统评估172. Molded part tooling quality control methods assessment -成型件工装质量控制方法评估173. Molded part tooling process improvement strategies implementation -成型件工装工艺改进策略实施174. Molded part tooling waste reduction techniques optimization -成型件工装废物减少技术优化175. Molded part tooling cost analysis tools -成型件工装成本分析工具176. Molded part tooling design review software -成型件工装设计审查软件177. Molded part tooling production efficiency evaluation -成型件工装生产效率评估178. Molded part tooling maintenance checklist optimization -成型件工装维护清单优化179. Molded part tooling repair cost estimation software -成型件工装修复成本估算软件180. Molded part tooling modification cost estimation software -成型件工装修改成本估算软件181. Molded part tooling replacement cost estimation software -成型件工装更换成本估算软件182. Molded part tooling storage system optimization -成型件工装存储系统优化183. Molded part tooling transportation cost calculation software -成型件工装运输成本计算软件184. Molded part tooling disposal methods evaluation tools -成型件工装处理方法评估工具185. Molded part tooling recycling process optimization techniques -成型件工装回收流程优化技术186. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施187. Molded part tooling risk assessment methods -成型件工装风险评估方法188. Molded part tooling safety protocols optimization -成型件工装安全协议优化189. Molded part tooling environmental impact assessment -成型件工装环境影响评估190. Molded part tooling sustainability evaluation -成型件工装可持续性评估191. Molded part tooling efficiency improvement strategies implementation -成型件工装效率提升策略实施192. Molded part tooling inventory management techniques -成型件工装库存管理技术193. Molded part tooling repair process optimization -成型件工装修复流程优化194. Molded part tooling modification cost reduction techniques -成型件工装修改成本降低技术195. Molded part tooling replacement cost reduction strategies -成型件工装更换成本降低策略196. Molded part tooling storage space optimization techniques -成型件工装存储空间优化技术197. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略198. Molded part tooling disposal methods optimization -成型件工装处理方法优化199. Molded part tooling recycling process evaluation -成型件工装回收流程评估200. Molded part tooling cost analysis techniques -成型件工装成本分析技术201. Molded part tooling design review process optimization -成型件工装设计审查流程优化202. Molded part tooling production efficiency improvement strategies -成型件工装生产效率提升策略203. Molded part tooling maintenance checklist evaluation -成型件工装维护清单评估204. Molded part tooling repair process efficiency improvement techniques -成型件工装修复流程效率提升技术205. Molded part tooling modification cost reduction strategies -成型件工装修改成本降低策略206. Molded part tooling replacement cost reduction techniques -成型件工装更换成本降低技术207. Molded part tooling storage system evaluation -成型件工装存储系统评估208. Molded part tooling transportation cost analysis techniques -成型件工装运输成本分析技术209. Molded part tooling disposal methods optimization strategies -成型件工装处理方法优化策略210. Molded part tooling recycling process efficiency improvement techniques -成型件工装回收流程效率提升技术211. Molded part tooling cost reduction strategies implementation -成型件工装成本降低策略实施212. Molded part tooling risk assessment techniques -成型件工装风险评估技术213. Molded part tooling safety protocols evaluation -成型件工装安全协议评估214. Molded part tooling environmental impact assessment techniques -成型件工装环境影响评估技术215. Molded part tooling sustainability improvement strategies -成型件工装可持续性改进策略216. Molded part tooling efficiency evaluation techniques -成型件工装效率评估技术217. Molded part tooling inventory management optimization -成型件工装库存管理优化218. Molded part tooling repair process efficiency evaluation -成型件工装修复流程效率评估219. Molded part tooling modification cost reduction strategies implementation -成型件工装修改成本降低策略实施220. Molded part tooling replacement cost reduction techniques implementation -成型件工装更换成本降低技术实施221. Molded part tooling storage space optimization strategies -成型件工装存储空间优化策略222. Molded part tooling transportation cost reduction techniques implementation -成型件工装运输成本降低技术实施223. Molded part tooling disposal methods optimization techniques -成型件工装处理方法优化技术224. Molded part tooling recycling process efficiency evaluation -成型件工装回收流程效率评估225. Molded part tooling cost analysis techniques implementation -成型件工装成本分析技术实施226. Molded part tooling design review process optimization strategies -成型件工装设计审查流程优化策略227. Molded part tooling production efficiency improvement techniques implementation -成型件工装生产效率提升技术实施228229. Molded part tooling quality control measures evaluation -成型件工装质量控制措施评估230. Molded part tooling inspection process optimization strategies -成型件工装检验过程优化策略231. Molded part tooling maintenance schedule development -成型件工装维护计划制定232. Molded part tooling repair cost analysis techniques -成型件工装修复成本分析技术233. Molded part tooling modification process efficiency improvement techniques implementation -成型件工装修改过程效率提升技术实施234. Molded part tooling replacement process cost reduction strategies implementation -成型件工装更换过程成本降低策略实施235. Molded part tooling storage system optimization -成型件工装存储系统优化236. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术实施237. Molded part tooling disposal methods evaluation -成型件工装处理方法评估238. Molded part tooling recycling process efficiency improvement techniques implementation -成型件工装回收流程效率提升技术实施239. Molded part tooling cost reduction strategies evaluation -成型件工装成本降低策略评估240. Molded part tooling risk assessment techniques implementation -成型件工装风险评估技术实施241. Molded part tooling safety protocols optimization strategies -成型件工装安全协议优化策略242. Molded part tooling environmental impact assessment techniques implementation -成型件工装环境影响评估技术实施243. Molded part tooling sustainability improvement strategies evaluation -成型件工装可持续性改进策略评估244. Molded part tooling efficiency evaluation techniques implementation -成型件工装效率评估技术实施245. Molded part tooling inventory management optimization strategies implementation -成型件工装库存管理优化策略实施246. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复流程效率评估技术247. Molded part tooling modification cost reduction strategies evaluation -成型件工装修改成本降低策略评估248. Molded part tooling replacement cost reduction techniques evaluation -成型件工装更换成本降低技术评估249. Molded part tooling storage space optimization strategies implementation -成型件工装存储空间优化策略实施250. Molded part tooling transportation cost reduction techniques evaluation -成型件工装运输成本降低技术评估251. Molded part tooling design optimization techniques implementation -成型件工装设计优化技术实施252. Molded part tooling production capacity evaluation -成型件工装生产能力评估253. Molded part tooling inspection methods improvement strategies -成型件工装检验方法改进策略254. Molded part tooling maintenance cost analysis techniques -成型件工装维护成本分析技术255. Molded part tooling repair process optimization strategies implementation -成型件工装修复过程优化策略实施256. Molded part tooling modification process cost reduction techniques -成型件工装修改过程成本降低技术257. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术258. Molded part tooling storage system efficiency improvement strategies implementation -成型件工装存储系统效率提升策略实施259. Molded part tooling transportation cost reduction strategies evaluation -成型件工装运输成本降低策略评估260. Molded part tooling disposal methods optimization techniques implementation -成型件工装处理方法优化技术实施261. Molded part tooling quality control measures implementation -成型件工装质量控制措施实施262. Molded part tooling material selection criteria evaluation -成型件工装材料选择标准评估263. Molded part tooling cost estimation techniques implementation -成型件工装成本估算技术实施264. Molded part tooling waste reduction strategies evaluation -成型件工装废料减少策略评估265. Molded part tooling energy consumption optimization techniques -成型件工装能源消耗优化技术266. Molded part tooling production cycle time reduction strategies evaluation -成型件工装生产周期缩短策略评估267. Molded part tooling training programs implementation -成型件工装培训计划实施268. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略269. Molded part tooling inspection frequency evaluation techniques -成型件工装检验频率评估技术270. Molded part tooling repair cost reduction strategies implementation -成型件工装修复成本降低策略实施271. Molded part tooling modification process efficiency evaluation techniques -成型件工装修改过程效率评估技术272. Molded part tooling replacement process cost reduction strategies -成型件工装更换过程成本降低策略273. Molded part tooling storage system organization techniques implementation -成型件工装存储系统组织技术实施274. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估275. Molded part tooling disposal methods cost evaluation techniques -成型件工装处理方法成本评估技术276. Molded part tooling quality assurance audits implementation -成型件工装质量保证审计实施277. Molded part tooling material sourcing optimization strategies -成型件工装材料采购优化策略278. Molded part tooling cost control measures implementation -成型件工装成本控制措施实施279. Molded part tooling waste management techniques evaluation -成型件工装废料管理技术评估280. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略281. Molded part tooling production planning optimization techniques implementation -成型件工装生产计划优化技术实施282. Molded part tooling training effectiveness evaluation techniques -成型件工装培训效果评估技术283. Molded part tooling maintenance cost reduction strategies evaluation -成型件工装维护成本降低策略评估284. Molded part tooling inspection methods optimization techniques -成型件工装检验方法优化技术285. Molded part tooling repair process cost reduction strategies implementation -成型件工装修复过程成本降低策略实施286. Molded part tooling modification process efficiency improvement techniques -成型件工装修改过程效率提升技术287. Molded part tooling replacement process safety protocols evaluation -成型件工装更换过程安全协议评估288. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略289. Molded part tooling transportation cost analysis techniques implementation -成型件工装运输成本分析技术290. Molded part tooling disposal methods efficiency evaluation techniques -成型件工装处理方法效率评估技术291. Molded part tooling quality control system implementation -成型件工装质量控制系统实施292. Molded part tooling material selection process optimization strategies -成型件工装材料选择过程优化策略293. Molded part tooling cost estimation accuracy evaluation techniques -成型件工装成本估算准确度评估技术294. Molded part tooling waste reduction techniques implementation -成型件工装废料减少技295. Molded part tooling energy consumption monitoring system implementation -成型件工装能耗监测系统实施296. Molded part tooling production scheduling optimization strategies -成型件工装生产调度优化策略297. Molded part tooling training program development techniques -成型件工装培训计划开发技术298. Molded part tooling maintenance schedule optimization strategies -成型件工装维护计划优化策略299. Molded part tooling inspection frequency optimization techniques -成型件工装检验频率优化技术300. Molded part tooling repair process efficiency improvement strategies -成型件工装修复过程效率提升策略301. Molded part tooling replacement cost analysis techniques -成型件工装更换成本分析技术302. Molded part tooling storage system organization techniques -成型件工装存储系统组织技术303. Molded part tooling transportation safety protocols implementation -成型件工装运输安全协议实施304. Molded part tooling disposal methods cost analysis techniques -成型件工装处理方法成本分析技术305. Molded part tooling quality control system evaluation techniques -成型件工装质量控制系统评估技术306. Molded part tooling material selection process efficiency evaluation techniques -成型件工装材料选择过程效率评估技术307. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确度提升策略308. Molded part tooling waste management system implementation -成型件工装废料管理系统实施309. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术310. Molded part tooling production scheduling efficiency evaluationtechniques -成型件工装生产调度效率评估技术311. Molded part tooling training program effectiveness evaluation techniques -成型件工装培训计划效果评估技术312. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术313. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略314. Molded part tooling repair process cost analysis techniques -成型件工装修复过程成本分析技术315. Molded part tooling replacement process efficiency evaluation techniques -成型件工装更换过程效率评估技术316. Molded part tooling storage system space utilization techniques -成型件工装存储系统空间利用技术317. Molded part tooling transportation cost reduction strategies -成型件工装运输成本降低策略318. Molded part tooling disposal methods efficiency improvement strategies -成型件工装处理方法效率提升策略319. Molded part tooling quality control system implementation techniques -成型件工装质量控制系统实施技术320. Molded part tooling material selection process optimization techniques -成型件工装材料选择过程优化技术321. Molded part tooling cost estimation accuracy improvementtechniques -成型件工装成本估算准确度提升技术322. Molded part tooling waste reduction strategies implementation -成型件工装废料减少策略实施323. Molded part tooling energy consumption monitoring system optimization techniques -成型件工装能耗监测系统优化技术324. Molded part tooling production scheduling efficiency improvement strategies -成型件工装生产调度效率提升策略325. Molded part tooling training program development techniques -成型件工装培训计划开发技术326. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术327. Molded part tooling inspection frequency optimization strategies -成型件工装检验频率优化策略328. Molded part tooling repair process efficiency evaluation techniques -成型件工装修复过程效率评估技术329. Molded part tooling replacement cost analysis methods -成型件工装更换成本分析方法330. Molded part tooling storage system organization strategies -成型件工装存储系统组织策略331. Molded part tooling transportation safety protocols evaluation -成型件工装运输安全协议评估332. Molded part tooling disposal methods cost analysis methods -成型件工装处理方法成本分析方法333. Molded part tooling quality control system effectiveness evaluation techniques -成型件工装质量控制系统效果评估技术334. Molded part tooling material selection process efficiency improvement strategies -成型件工装材料选择过程效率提升策335. Molded part tooling cost optimization techniques -成型件工装成本优化技术336. Molded part tooling maintenance record keeping methods -成型件工装维护记录保持方法337. Molded part tooling inspection checklist development techniques -成型件工装检查清单开发技术338. Molded part tooling repair process time reduction strategies -成型件工装修复过程时间减少策略339. Molded part tooling replacement frequency analysis methods -成型件工装更换频率分析方法340. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术341. Molded part tooling transportation route optimization strategies -成型件工装运输路线优化策略342. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术343. Molded part tooling quality control system auditing methods -成型件工装质量控制系统审核方法344. Molded part tooling material selection process cost analysis techniques -成型件工装材料选择过程成本分析技术345. Molded part tooling cost estimation error analysis techniques -成型件工装成本估算误差分析技术346. Molded part tooling waste reduction strategies implementation monitoring techniques -成型件工装废料减少策略实施监测技术347. Molded part tooling energy consumption reduction techniques -成型件工装能耗减少技术348. Molded part tooling production scheduling optimization techniques -成型件工装生产调度优化技术349. Molded part tooling training program effectiveness evaluation methods -成型件工装培训计划效果评估方法350. Molded part tooling maintenance schedule flexibility strategies -成型件工装维护计划灵活性策略351. Molded part tooling design software proficiency assessment methods -成型件工装设计软件熟练度评估方法352. Molded part tooling cost reduction strategies implementation monitoring techniques -成型件工装成本降低策略实施监测技术353. Molded part tooling storage system space optimization strategies -成型件工装存储系统空间优化策略354. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法355. Molded part tooling disposal methods regulatory compliance evaluation techniques -成型件工装处理方法合规性评估技术356. Molded part tooling quality control system training program development techniques -成型件工装质量控制系统培训计划开发技术357. Molded part tooling material selection process sustainability assessment methods -成型件工装材料选择过程可持续性评估方法358. Molded part tooling cost estimation accuracy improvement strategies -成型件工装成本估算准确性提升策略359. Molded part tooling waste management system implementation techniques -成型件工装废料管理系统实施技术360. Molded part tooling energy efficiency improvement strategies -成型件工装能效提升策略361. Molded part tooling production scheduling flexibility analysis methods -成型件工装生产调度灵活性分析方法362. Molded part tooling training program effectiveness evaluation criteria -成型件工装培训计划效果评估标准363. Molded part tooling maintenance schedule optimization techniques -成型件工装维护计划优化技术364. Molded part tooling design optimization methods for reducing defects -成型件工装设计优化方法降低缺陷365. Molded part tooling cost estimation techniques for new product development -成型件工装成本估算技术新产品开发366. Molded part tooling storage system inventory tracking methods -成型件工装存储系统库存跟踪方法367. Molded part tooling transportation risk mitigation strategies -成型件工装运输风险缓解策略368. Molded part tooling disposal methods environmental sustainability evaluation techniques -成型件工装处理方法环境可持续性评估技术369. Molded part tooling quality control system documentation management techniques -成型件工装质量控制系统文件管理技术370. Molded part tooling material selection process sustainability improvement strategies -成型件工装材料选择过程可持续性改善策略371. Molded part tooling cost estimation error reduction techniques -成型件工装成本估算误差减少技术372. Molded part tooling waste reduction strategies effectiveness evaluation methods -成型件工装废料减少策略效果评估方法373. Molded part tooling energy consumption monitoring techniques -成型件工装能耗监测技术374. Molded part tooling production scheduling optimization tools -成型件工装生产调度优化工具375. Molded part tooling training program evaluation methods -成型件工装培训计划评估方法376. Molded part tooling maintenance schedule adjustment techniques -成型件工装维护计划调整技术377. Molded part tooling design software selection criteria -成型件工装设计软件选择标准378. Molded part tooling cost reduction strategies effectiveness evaluation methods -成型件工装成本降低策略效果评估方法379. Molded part tooling storage system organization tools -成型件工装存储系统组织工具380. Molded part tooling transportation risk mitigation measures -成型件工装运输风险缓解措施381. Molded part tooling disposal methods regulatory compliance monitoring techniques -成型件工装处理方法合规性监测技术382. Molded part tooling quality control system training program evaluation methods -成型件工装质量控制系统培训计划评估方法383. Molded part tooling material selection process cost-benefit analysis techniques -成型件工装材料选择过程成本效益分析技术384. Molded part tooling waste management strategies sustainability assessment methods -成型件工装废料管理策略可持续性评估方法385. Molded part tooling energy efficiency improvement measures -成型件工装能效改善措施386. Molded part tooling production scheduling optimization algorithms-成型件工装生产调度优化算法387. Molded part tooling training program effectiveness evaluation tools -成型件工装培训计划效果评估工具388. Molded part tooling maintenance schedule optimization models -成型件工装维护计划优化模型389. Molded part tooling design optimization techniques for improving product performance -成型件工装设计优化技术提高产品性能390. Molded part tooling cost estimation methods for budget planning -成型件工装成本估算方法预算规划391. Molded part tooling storage system inventory management techniques -成型件工装存储系统库存管理技术392. Molded part tooling transportation risk assessment methods -成型件工装运输风险评估方法393. Molded part tooling disposal methods environmental impact assessment techniques -成型件工装处理方法环境影响评估技术394. Molded part tooling quality control system documentation control methods -成型件工装质量控制系统文件控制方法395. Molded part tooling material selection process sustainability evaluation criteria -成型件工装材料选择过程可持续性评估标准396. Molded part tooling cost estimation accuracy improvement techniques -成型件工装成本估算准确性改善技术397. Molded part tooling waste reduction strategies monitoring methods。
模具英语词汇整理
模具词典模具词典组装组装、、冲压冲压、、喷漆等专业词汇喷漆等专业词汇Assembly line 组装线 Layout [ 5lei7aut ]布置图 Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌 OOBA 开箱检查fit together 组装在一起 fasten [ 5fB:sn ]锁紧(螺丝) fixture [ 5fikstFE ]夹具(治具) pallet [ 5pAlit ]栈板 barcode 条码barcode scanner 条码扫描器 fuse together 熔合 fuse machine 热熔机 repair [ ri5pZE ]修理 operator [ 5CpEreitE ]作业员 QC 品管supervisor 课长 ME 制造工程师 MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查 thumb screw 大头螺丝 lbs. inch 镑、英寸 EMI gasket 导电条 front plate 前板 rear plate 后板 chassis [ 5FAsi ]基座 bezel panel 面板 power button 电源按键 reset button 重置键Hi-pot test of SPS 高源高压测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts 塑胶件 SOP 制造作业程序material check list 物料检查表 work cell 工作间 trolley [ 5trRlI ]台车 carton [ 5kB:tEn ]纸箱 - sub-line 支线 left fork 叉车personnel resource department 人力资源部production department 生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机 punching machine 冲床robot[ 5rEubCt, 5rCbEt]机械手hydraulic machine油压机lathe[ leiT]车床planer |'plein|刨床miller[ 5milE]铣床grinder[ 5^raindE]磨床driller[ 5drilE]钻床linear cutting线切割electrical sparkle电火花welder[ 5weldE(r)]]电焊机staker=reviting machine铆合机 position[ pE5ziFEn]职务president[ 5prezidEnt]董事长general manager总经理special assistant manager特助 factory director厂长department director部长deputy manager | =vice manager副理 section supervisor课长deputy section supervisor =vice section superisor副课长 group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana 天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料 scraped |'skræpid|报废scrape ..v. [ skreIp]刮;削deficient purchase来料不良 manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|[ Cksi5deiFEn]氧化 scratch[ skrAtF]刮伤dents[ 5dents]压痕defective upsiding down抽芽不良 defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位 stamping-missing漏冲production capacity生产力 education and training教育与训练 proposal improvement提案改善spare parts=buffer备件forklift[ 5fC:klIft]叉车trailer=long vehicle拖板车 compound die合模die locker锁模器pressure plate=plate pinch压板bolt[ bEul]螺栓name of a department部门名称 administration/general affairs dept总务部automatic screwdriver电动启子 thickness gauge厚薄规gauge(or jig) [ ^edV]治具power wire电源线buzzle 蜂鸣器defective product label不良标签 identifying sheet list标示单 screwdriver holder起子插座pedal[ 5pedl]踩踏板stopper[ 5stCpE]阻挡器flow board流水板hydraulic handjack油压板车forklift[ 5fC:klIft]叉车 pallet[ 5pAli]栈板glove(s) [ ^lQv]手套glove(s) with exposed fingers割手套 thumb[ WQm]大拇指forefinger[ 5fC:7fiN^E]食指midfinger中指ring finger无名指little finger小指band-aid 创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper[ 5swi:pE]扫把mop[ mCp]拖把vaccum cleaner吸尘器rag [ rA^]抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain[ tFein]链条jack[ dVAk]升降机production line流水线chain[ tFein]链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格 dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head 螺丝滑头slipped screwhead/shippery screw thread滑手speckle[ 5spekl]斑点mildewed=moldy=mouldy发霉rust[ rQst]生锈deformation[ 7di:fC:5meiFEn]变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion[ in5klu:VEn]杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch[ skrAtF]划伤 poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱 painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位safety[ 5seifti]安全quality[ 5kwCliti]品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产 equipment[ i5kwipmEn]设备to start a press开机stop/switch off a press关机 classification[ 7klAsifi5keiFEn]整理 regulation[ re^ju5leiFEn]整顿 cleanness[ `kli:nnI]清扫conservation[ 7kCnsE(:)5veiFEn]清洁 culture教养qualified products, up-to-gradeproducts良品defective products, not up-to-grade products不良品waste[ weist]废料board[ bC:d]看板feeder[ 5fi:dE]送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade 隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩 character die字模to feed, feeding送料transportation[ 7trAnspC:5teiFEn]运输 (be)qualfied, up to grade合格not up to grade, not qualified不合格 material change, stock change材料变更 feature change 特性变更evaluation[ i7vAlju5eiFEn]评估prepare for, make preparations for 准备parameters[ pE5rAmitE]参数rotating speed, revolution转速 manufacture management制造管理 abnormal handling异常处理 production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换 engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床 uncoiler & strainghtener整平机 feeder[ 5fi:dE]送料机rack, shelf, stack料架cylinder[ 5silindE]油缸robot[ 5rEubCt, 5rCbE]机械手taker[ 5teikE]取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch[ intF]寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset[ 5ri:set]复位smoothly[ 5smu:TlI]顺利dent[ dent]压痕scratch[ skrAtF]刮伤deformation变形filings[ 5failiN]铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存 receive[ ri5si:v]领取 approval examine and verify审核 processing, to process加工 delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单 consume, consumption消耗to fill in填写abrasion[ E5breiVEn]磨损reverse angle = chamfer倒角 character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂 to lubricate润滑common vocabulary for die engineering模具工程常用词汇模具工程常用词汇die [ dai]模具figure file, chart file图档cutting die, blanking die冲裁模 progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边 to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸 engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条 upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板 spare dies模具备品spring []弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment[ i5kwipmEnt]设备waste materials废料work in progress product在制品 casing = containerazation装箱 quantity of physical invetory second count 复盘点数量quantity of customs count 会计师盘,点数量the first page第一联filed by accounting department forreference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financialdepartment) 本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO. 空白与作废单号plate[ pleit]电镀mold[ mEuld]成型material for engineering mold testing 工程试模材料not included in physical inventory不列入盘点sample[ 5sAmpl]样品incoming material to be inspected进货待验description[ dis5kripFEn]品名 steel/rolled steel钢材material statistics sheet 物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位 location[ lEu5keiFEn]地点chairman[ 5tFZEmEn]主席present members出席人员subject[ 5sQbdVik]主题conclusion[ kEn5klu:VEn]结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日 approved by / checked by / prepared by 核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model[ 5mCdl]机锺work order工令revision[ ri5viVEn]版次remark[ ri5mB:k]备注production control confirmation生产确认checked by初审approved by核准department[ di5pB:tmEnt]部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用 obsolete material良品已呆滞to be inspected or reworked待验或重工total[ 5tEutl]合计cause description原因说明part number/ P/N 料号type[ taip]形态item/group/class类别quality[ 5kwCliti]品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表 physical inventory盘点数量physical count quantity帐面数量 difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance[ 5tClErEns]工差score=groove压线cam block滑块pilot[ 5pailEt]导正筒trim[ trim]剪外边pierce[ piEs]剪内边drag form压锻差pocket for the punch head挂钩槽 slug hole废料孔feature die公母模expansion dwg展开图radius[ 5reidjEs]半径shim(wedge) [ Fim]楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子 shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆 spring-box eject-plate弹簧箱顶板 bushing block衬套insert [ in5sE:t]入块club car高尔夫球车capability[ 7keipE5biliti]能力 parameter[ pE5rAmitE]参数factor[ 5fAktE]系数phosphate[ 5fCsfei]皮膜化成viscosity[ vis5kCsit]涂料粘度 alkalidipping[ 5AlkElifaitEbl]脱脂 main manifold主集流脉bezel[ 5bezEl]斜视规blanking[ 5blANkiN]穿落模dejecting顶固模 demagnetization去磁;消磁high-speed transmission高速传递 heat dissipation热传rack[ rAk]上料degrease[ di:5^ri:z]脱脂rinse[ rins]水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate[ 5krEumeit]铬酸处理 Anodize[ 5AnEJdaI]阳性处理seal[ si:l]封孔revision[ ri5viVEn]版次part number/P/N料号good products良品scraped products报放心品 defective products不良品 finished products成品disposed products处理品 barcode 条码flow chart流程表单assembly[ E5sembli]组装stamping[ 5stAmpiN]冲压molding[ 5mEuldiN]成型spare parts=buffer备品 coordinate[ kEu5C:dinit]座标 dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple[ 5WE:mEu7kQpl]热电偶 sand blasting喷沙grit [ ^rit]砂砾derusting machine除锈机degate[ di:5^eit]打浇口dryer[ 5draiE]烘干机induction[ in5dQkFEn]感应induction light感应光response=reaction=interaction感应 ram[ rAm]连杆edge finder巡边器concave[ 5kCn5keiv]凸convex[ 5kCn5veks]凹short[ FC:t]射料不足nick[ nik]缺口speck[ spek]瑕??shine[ Fain]亮班splay [ splei]银纹gas mark焦痕delamination起鳞cold slug冷块blush [ blQF]导色gouge[ ^audV]沟槽;凿槽satin texture段面咬花witness line证示线patent[ 5peitEnt, 5pAtEnt]专利 grit[ ^rit]沙砾granule=peuet=grain细粒grit maker抽粒机cushion[ 5kuFEn]缓冲 magnalium镁铝合金 magnesium镁金metal plate钣金lathe[ leiT]车mill[ mil]锉plane[ plein]刨grind[ ^raind]磨drill[ dril]铝boring[ 5bC:riN]镗blinster[ `blIntsE]气泡fillet[ 5filit]镶;嵌边through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差 velocity[ vi5lCsiti]速度 production tempo生产进度现状 torque[ tC:k]扭矩spline=the multiple keys花键 quenching[ 5kwentFiN]淬火 tempering[ 5tempEriN]回火 annealing[ A5ni:liN]退火carbonization[ 7kB:bEnai5zeiFE]碳化 alloy[ 5AlCi]合金tungsten high speed steel钨高速的 moly high speed steel钼高速的 organic solvent有机溶剂bracket[ 5brAkit]小磁导liaison[ li(:)5eizB:n, -zEn]联络单 volatile[ 5vClEtail]挥发性 resistance[ ri5zistEns]电阻 ion[ 5aiEn]离子titrator[ 5taitreitE]滴定仪 beacon[ 5bi:kEn]警示灯 coolant[ 5ku:lEnt]冷却液 crusher[ 5krQFE]破碎机模具工程类模具工程类accurate die casting 精密压铸 powder forming 粉末成形 calendaring molding 压延成形 powder metal forging 粉末锻造 cold chamber die casting 冷式压铸 precision forging 精密锻造 cold forging 冷锻press forging 冲锻 compacting molding 粉末压出成形rocking die forging 摇动锻造 compound molding 复合成形 rotary forging 回转锻造 compression molding 压缩成形rotational molding 离心成形 dip mold 浸渍成形rubber molding 橡胶成形 encapsulation molding 注入成形 sand mold casting 砂模铸造 extrusion molding 挤出成形 shell casting 壳模铸造 foam forming 发泡成形 sinter forging 烧结锻造 forging roll 轧锻six sides forging 六面锻造 gravity casting 重力铸造 slush molding 凝塑成形 hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸swaging [ 5sweidViN]挤锻hot forging 热锻 transfer molding 转送成形 injection molding 射出成形 warm forging 温锻 investment casting 精密铸造 matched die method 对模成形法 laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具 burnishing die 挤光模landed positive mold 有肩全压式模具 button die 镶入式圆形凹模 loading shoe mold 料套式模具 center-gated mold 中心浇口式模具 loose detail mold 活零件模具 chill mold 冷硬用铸模loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模 composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模modular mold 组合式模具 double stack mold 双层模具multi-cavity mold 多模穴模具 electroformed mold 电铸成形模multi-gate mold 复式浇口模具 expander die 扩径模offswt bending die 双折冷弯模具 extrusion die 挤出模 palletizing die 迭层模 family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模 porous mold 通气性模具 duplicated cavity plate 复板模 positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模flash mold 溢料式模具 progressive die 顺序模 gypsum mold 石膏铸模protable mold 手提式模具 hot-runner mold 热流道模具 prototype mold 雏形试验模具 ingot mold 钢锭模 punching die 落料模 lancing die 切口模 raising(embossing) 压花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具 segment mold 组合模semi-positive mold 半全压式模具 shaper [ 5FeipE]定型模套single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具 sprueless mold 无注道残料模具 squeezing die 挤压模stretch form die 拉伸成形模 sweeping mold 平刮铸模swing die 振动模具figure file, chart file图档cutting die, blanking die冲裁模 progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边 to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸 engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品spring [ spriN]弹簧bolt[ bEult]螺栓plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce[ piEs]冲孔forming成型(抽凸,冲凸)draw hole抽孔bending[ 5bendiN]折弯trim[ trim]切边emboss[ im5bCs]凸点dome[ dEum]凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove[ ^ru:v]压线blanking[ 5blANkiN]下料 stamp letter冲字(料号) shearing[ 5FiEriN]剪断tick-mark nearside正面压印 tick-mark farside反面压印 冲压名称类extension dwg展开图 procedure dwg工程图die structure dwg模具结构图 material[ mE5tIErIEl]材质 material thickness料片厚度 factor[ 5fAktE]系数upward[ 5QpwEd]向上 downward[ 5daunwEd]向下 press specification冲床规格 die height range适用模高 die height闭模高度burr[ bE:]毛边gap[ ^Ap]间隙weight[ weit]重量total wt.总重量punch wt.上模重量五金零件类五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉 dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒 pin销 lifter guide pin浮升导料销 guide pin导正销wire spring圆线弹簧outer guiding post外导柱 stop screw止付螺丝located pin定位销outer bush外导套模板类模板类top plate上托板（顶板） top block上垫脚punch set上模座punch pad上垫板punch holder上夹板 stripper pad脱料背板 up stripper上脱料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板 lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类零件类punch[ pQntF]冲头insert[ in5sE:t]入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子 bending block折刀roller[ 5rEulE]滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆 trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子 ribbon punch压筋冲子reel-stretch punch卷圆压平冲子 guide plate定位板sliding block滑块sliding dowel block滑块固定块 active plate活动板lower sliding plate下滑块板 upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆 spring-box eject-plate弹簧箱顶板 bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具 split mold分割式模具 cavity[ 5kAviti]型控 母模core[ kC:]模心 公模taper[ 5teipE]锥拔leather cloak仿皮革shiver[ 5FivE]饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw 自攻螺丝 striper plate 脱料板 piston [ 5pistEn ]活塞cylinder 汽缸套 chip [ tFip ]细碎物 handle mold 手持式模具移转移转成型用模具成型用模具成型用模具 encapsulation molding 低压封装成型 射出成型用模具two plate 两极式（模具） well type 蓄料井insulated runner 绝缘浇道方式 hot runner 热浇道 runner plat 浇道模块 valve gate 阀门浇口 band heater 环带状的电热器 spindle [ 5spindl ]阀针 spear head 刨尖头 slag well 冷料井 cold slag 冷料渣 air vent 排气道 h=0.02~0.05mm w=3.2mm L=3~5mmwelding line 熔合痕 eject pin 顶出针 knock pin 顶出销 return pin 回位销反顶针 sleave [ sli:v ]套筒 stripper plate 脱料板 insert core 放置入子runner stripper plate 浇道脱料板 guide pin 导销eject rod (bar)（成型机）顶业捧 subzero [ 7sQb5ziErEu ]深冷处理 three plate 三极式模具 runner system 浇道系统 stress crack 应力电裂 orientation [ ]定向sprue gate 射料浇口，直浇口 nozzle [ ]射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井 side gate 侧浇口 edge gate 侧缘浇口 tab gate 搭接浇口 film gate 薄膜浇口 flash gate 闸门浇口 slit gate 缝隙浇口 fan gate 扇形浇口 dish gate 因盘形浇口 H=F=1/2t~1/5t T=2.5~3.5mmdiaphragm gate 隔膜浇口 ring gate 环形浇口subarine gate潜入式浇口 tunnel gate隧道式浇口 pin gate针点浇口Φ0.8~1.0mmRunner less无浇道 (sprue less)无射料管方式 long nozzle延长喷嘴方式 sprue[ spru]浇口;溶渣品质人员名称类品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员 OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数 SSQA standardized supplier quality 合格供应商品质评估 OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析 8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类运作类AQL Acceptable Quality Level 运作类允收品质水准 S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务 MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一 PPM Percent Per Million 批号制程统计品管专类制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否 DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划 执行 检查 总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping 中国制造作业规范 CQCA C-China Q-Quality c-Compaq A-Assembly中国组装品管作业规范 CQCP C-China Q-Quality c-Compaq P-Painting中国烤漆品管作业规范 部类部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部 PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部 DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码 SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它其它OEM Original Equipment Manufacture 原设备制造 PCE Personal Computer Enclosure 个人电脑外设 PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语 整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to5M Man,Machine,Material,Method,Measurement4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源) SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID Engineering 计算机模拟ABIOS Achanced Basic in put/output system 先进的基本输入/输出系统 CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体 PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微通道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构 SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板 CAR Correction Action Report 改善报告 NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求 PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养 MRP Material Requiremcnt Planning 物料需计划 OC Operation System 作业系统 TBA To Be Design 待定,定缺 D/C Drawing Change P/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业 RFI Read Frequency Input 读频输入 MMC Maximum Material Condition MMS Maximum Material Size LMC Least Material Condition LMS Least Material Size模具技术用语模具技术用语 各种模具常用成形方式各种模具常用成形方式 accurate die casting 精密压铸 powder forming 粉末成形 calendaring molding 压延成形 powder metal forging 粉末锻造 cold chamber die casting 冷式压铸 precision forging 精密锻造 cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造 compound molding 复合成形 rotary forging 回转锻造 compression molding 压缩成形 rotational molding 离心成形 dip mold 浸渍成形 rubber molding 橡胶成形。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
模具英语词汇表
A
abrasive grinding 强力磨削abrasive['breisiv] a.磨料的, 研磨的
absence ['bs ns] n.. 不在，缺席accessory[k'ses ri] n.附件
accommodate['k m deit] v. 适应
accordingly['k:di li] adv.因此,从而,相应地
accuracy['kjur si] n精度,准确性
actuate['ktjueit] vt.开动(机器), 驱动
adequate['dikwit] a. 足够的adhesive[d'hi:siv] n. 粘合剂
adjacent['d eisnt] a. 邻近的
adopt['d pt] vt. 采纳advance [d'v:ns] n.进步advisable [d'vaizbl] adj. 可取的agitate['d iteit] v. 摇动
a large extent 专门大程度algorithm ['l ri m] n. 算法
align ['lain] v 定位，调准alignment['lainm nt] n. 校直
all-too-frequent 频繁allowance['l uens] n. 容差, 余量
alternate[':lt nit]v.交替,轮流
alternative[:l't:n tiv]
n. 替换物
alternatively[:l't:n t ivli] ad. 做为选择, 也许aluminum[lju'minj m] n.铝
ample['mpl] adj. 充足的analysis ['n l sis] n. 分析
ancillary['nsil ri] a.补助的, 副的
angular ['jul] adj. 有角的
annealing['li:li ] n.退火
aperture ['p t ] n.孔applied loads 作用力appropriate ['pr uprieit] a. 适当的
arc[a:k] n.弧, 弓形
arise['raiz] vi. 出现, 发生
arrange['reid] v. 安排article['a:tikl] n.制品, 产品
ascertain[s'tein] vt. 确定, 查明
assemble['sembl] vt.组装attitude ['titju:d] n 态度auxiliary
[:'zilj ri]adj. 辅助的avoid['v id] v.幸免
axis['ksis] n.轴
axle['ksl] n.轮轴, 车轴
B
backup['b k p] n. 备份batch [b t ] n 一批bearing['b ri] n.轴承,支座
bed[bed] n. 床身behavior[bi'heivj] n. 性能bench-work 钳工工作
bend[bend] v.弯曲
beneath[bi'ni:] prep 在···下
bin [bin] n. 仓，料架
blank [bl k] n. 坯料blank [bl k] v. 冲裁,落料blanking tool 落料模
blast [bl st] n.一阵（风）
blemish['blemi] n. 缺点, 污点
bolster['b ulst] n. 模座,垫板
boost[bu:st] n. 推进
boring['b:ri] n.镗削, 镗孔
bracket ['br kit] n. 支架brass [br s] n.黄铜
break down 破坏breakage ['breikid] n.破坏bridge piece
brine[brain] n. 盐水
brittle['britl] adv.易碎的buffer [b f] n.缓冲器built-in 内装的
bulging [b ld i] n. 凸肚burr [b:] n. 毛刺
bush [bu ] n. 衬套
bush[bu]n. 衬套
by far (修饰比较级, 最高级)···得多, 最
by means of 借助于
C
cabinet ['k binit] n.橱柜call upon 要求
carbide['ka:baid] n.碳化物carburizing['ka:bjureti]。