UB216SKW035F;UB215KKW015F-1JF;UB226SKG035F-1JB;UB215KKW016CF-1JB;中文规格书,Datasheet资料

Series UB2Low Profile PushbuttonsI n d i c a t o r sA c c e s s o r i e sS u p p l e m e n t T a c t i l e sK e y l o c k s R o t a r i e sP u s h b u t t o n sS l i d e s P r o g r a m m a b l R o c k e r sT o u c hT i l tT o g g l e sGeneral SpecificationsElectrical Capacity (Resistive Load)Power Level (silver): 5A @ 125/250V AC or 5A @ 30V DC Logic Level (gold):0.4VA maximum @ 28V AC/DC maximum(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)Note: Find additional explanation of operating range in Supplement section.Other RatingsContact Resistance: 50 milliohms maximum for silver; 100 milliohms maximum for gold Insulation Resistance: 200 megohms minimum @ 500V DCDielectric Strength:1,000V AC minimum between contacts for 1 minute minimum;1,500V AC minimum between contacts & case for 1 minute minimum Mechanical Life:1,000,000 operations minimum for momentary;200,000 operations minimum for alternate action Electrical Life:10,000 operations minimum for silver;200,000 operations minimum for gold Nominal Operating Force:Single Pole: 1.90NDouble Pole: 2.55N Contact Timing:Break before makeTravel: Pretravel .067” (1.7mm); Overtravel .024” (0.6mm); Total Travel .091” (2.3mm) Materials & FinishesHousing/Bezel: Glass fiber reinforced polyamide (UL94V-0) Snap-in Frame: Stainless steel Movable Contactor: Phosphor bronzeMovable Contacts: Silver alloy or copper with gold plating Stationary Contacts: Silver alloy or copper with gold plating Switch Terminals: Phosphor bronze with silver or gold plating Lamp Terminals: Brass with tin platingBase:Glass fiber reinforced liquid crystal polymer (UL94V-0)Environmental DataOperating Temperature Range: –25°C through +50°C (–13°F through +122°F) for Illuminated –25°C through +70°C (–13°F through +158°F) for Nonilluminated Humidity: 90 ~ 95% humidity for 240 hours @ 40°C (104°F)Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hoursShock: 50G (490m/s 2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)InstallationCap Installation Force: 15.0N maximum downward force on capProcessingSoldering: Wave Soldering (PC version): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section.Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution.Standards & CertificationsFlammability Standards: UL94V-0 housing/bezel & baseUL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL” before dash in part number to order UL recognized switch. UL recognized only when ordered switch body with cap assembled. All single & double pole models recognized at 5A @ 125/250V AC or 0.014A @ 28V DC.Series UB2Low Profile PushbuttonsI n d i c a t o r sA c c e s s o r i e s S u p p l e m e n t T a c t i l e s K e y l o c k s R o t a r i e s P u s h b u t t o n sS l i d e s P r o g r a m m a b l T o g g l esR o c k e r sT o u c h T i l t Distinctive CharacteristicsWide selection of illumination effects is achieved with single and bicolor, 1- or 6-element LEDs in flat, beveled, or sculptured caps.Alternating legends (patent pending) in choice of sculptured or flat caps, combined with super bright bicolor LED. Combination of PCB mountability and short body allows use in compact applications.Small behind panel dimension for snap-in mounting in tight spaces.Snap-acting contact mechanism provides sensitive actuation with audible feedback; quick-make, quick-break characteristic limits arcing and prolongs electrical life.Latchdown mechanism, independent of switching mechanism, gives outstanding stability and reliability plus visible and tactile indication of circuit status.Terminals are epoxy sealed to lock out flux, solvents, and other contaminants.Momentary and alternate action circuits available in the same space-saving body size.Matching indicators available.Actual Size6ONONAlternate Action with LatchdownDESCRIPTION FOR TYPICAL ORDERING EXAMPLEUB215SKG035C-1JCSPDTON-(ON) CircuitGold Contacts with 0.4VA RatingSquare with PCB MountingStraight PC TerminalsRed, Bright LED and Sculptured Cap withClear Lens and Red DiffuserTYPICAL SWITCH O* Wire harness & cable assemblies offered only in AmericasIMPORTANT:Switches are supplied without UL & cULus marking unless specified.UL & cULus recognized only when ordered with marking on the switch.Specific models, ratings, & ordering in-structions are noted on General Specifi-cations page.Series UB2I n d i c a t o r sA c c e s s o r i e sS u p p l e m e n tT a c t i l es K e y l o c k sR o t a r i e s P u s h b u t t o n sS l i d e sP r o g r a m m a b l R o c k e r sT o u c hT i l t T o g g l e sSeries UB2Low Profile PushbuttonsI n d i c a t o r sA c c e s s o r i e sS u p p l e m e n tT a c t i l e sK e y l o c k sR o t a r i e sP u s h b u t t o n sS l i d e sP r o g r a m m a b l R o c k e r sT o u c hT i l tT o g g l e sMOUNTING TYPES & SHAPESSWITCH & LAMP TERMINALSCONTACT MATERIALS & RATINGSPCB MountingSKSquare SP , Single Color LEDDP , Single Color LEDSP , Bicolor LEDDP , Bicolor LEDSnap-in Mounting (Solder Lug)KKSquarewith Built-in BezelPanel Thickness: .039 ~ .126”(1.0 ~ 3.2mm)Silver Contacts Power Level 5A @ 125V AC & 250V ACGold Contacts Logic Level 0.4V A maximum @ 28V AC/DC maximumComplete explanation of operating range in Supplement section.W G0103Solder LugStraight PC* When in latchdown position for the alternate circuit, cap positions above the housing are:.059” (1.5mm) for snap-in models & .276” (7.0mm) for PCB models.For Switch & Bright LEDFor Super Bright & Bicolor LEDFor Super Bright & Bicolor LEDThk = (0.5) .020Thk = (0.5) .020For Switch & Bright LEDThk = (0.5) .020Thk = (0.5) .020Series UB2Low Profile PushbuttonsI n d i c a t o r s A c c e s s o r i e s S u p p l e m e n t T a c t i l e s K e y l o c k s R o t a r i e s P u s h b u t t o n sS l i d e s P r o g r a m m a b l T o g g l e sR o c k e r sT o u c h T i l t BRIGHT LED & CAPSThe electrical specifications shown are determined at a basic temperature of 25°C.LED circuit is isolated and requires an external power source. Polarity marks are on the bottom of the switch.If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section.The LED is an integral part of the switch and not available separately.JB JC JD JF1B JB JC JD JFCD FMaterial: PolycarbonateFinish: Glossy23AT3075Clear/White Clear/Amber Clear/Red Clear/GreenClear/White Clear/Amber Clear/GreenClear/Red White Amber GreenRed Clear Lens Translucent Colored DiffuserTranslucent Colored CapClear LensTranslucent Colored DiffuserLens/Diffuser Colors Available:Cap Colors Available:Lens/Diffuser Colors Available:AT3074 AT3076 FlatBright Single Color LED with 1 elementElectrical Specifications for Bright LEDColorRed Amber Green Unit Forward Peak Current I FM 303025mA Typical Forward Current I F 202020mA Forward Voltage V F 1.85 2.0 2.1V Reverse Peak VoltageV RM 555V Current Reduction Rate Above 25°C ∆I F0.400.420.46mA/°C Ambient Temperature Range–25° ~ +50°°C5C 5D 5FCaps for Bright LEDSeries UB2Low Profile PushbuttonsI n d i c a t o r sA c c e s s o r i e sS u p p l e m e n t T a c t i l e sK e y l o c k sR o t a r i e sP u s h b u t t o n sS l i d e sP r o g r a m m a b l R o c k e r sT o u c hT i ltT o g g l e sAT3075B Beveled White CapTranslucent White CapAT3074JB Sculptured Clear Lens/White DiffuserAT3076JB FlatClear Lens/White DiffuserCaps for Super Bright LED1JB2B3JBMaterial: PolycarbonateFinish: GlossySUPER BRIGHT LEDS & CAPSSuper Bright Single Color LED with 1 elementElectrical Specifications for Super Bright LEDSThe electrical specifications shown are determined at a basic temperature of 25°C.LED circuit is isolated and requires an external power source. Polarity marks are on the bottom of the switch.If the source voltage exceeds the rated voltage, a ballast resistor is required. The resistor value can be calculated by using the formula in the Supplement section.The LED is an integral part of the switch and not available separately.SUPER BRIGHT BICOLOR LED & CAPSElectrical Specifications for Super Bright Bicolor LEDLC (+)Super Bright Bicolor LED with 2 elementsAmber color is achieved by lighting red and greensimultaneously, but is not suitable for Alternating Legends.Series UB2Low Profile PushbuttonsI n d i c a t o r sA c c e s s o r i e s S u p p l e m e n t T a c t i l e sK e y l o c k s R o t a r i e s P u s h b u t t o n sS l i d e sP r o g r a m m a b l T o g g l e sR o c k e rs T o u c hT i l tMaterial: PolycarbonateFinish: GlossyCaps for Super Bright Bicolor LED010204Cap illumination is alternating green/red; legend text is black.Contact factory for other Alternating Legends.Legend illustrations are approximate representations of the actual characters on the filters.O N OFFSTART STOPOPEN CLOSEG reen Red G reen RedG reen RedTranslucent White DiffuserTranslucent White DiffuserClear LensAlternating Legend FilterClear LensAlternating Legend Filter AT3075B Beveled White CapAT3074JB Sculptured Clear Lens/White DiffuserAT3076JB FlatClear Lens/White Diffuser1JB 2B3JBAT3069J Sculptured Cap with Alternating Legend4JAT3070J Flat Capwith Alternating Legend5JMaterial: PolycarbonateFinish: GlossyAlternating Legend Caps for Super Bright Bicolor LEDStandard Alternating Legend PairsCAP TYPES & COLOR COMBINATIONS FOR NONILLUMINATEDAT3073 Sculptured4AT3077 Beveled5JA Lens/InsertColors Available:JB JC JD JFMaterial:Polycarbonate Finish: GlossyA CapColors Available:B C D FClear Lens OpaqueColored InsertOpaque Colored CapClear/Black Clear/White Clear/Red Clear/Amber Clear/GreenBlack White Red Amber GreenMaterial:Polycarbonate Finish: GlossyNo CodeNo LampSeries UB2Low Profile PushbuttonsI n d i c a t o r sA c c e s s o r i e sS u p p l e m e n tT a c t i l e sK e y l o c k sR o t a r i e sP u s h b u t t o n sS l i d e sP r o g r a m m a b l R o c k e r sT o uc hT i l tT o g g l e s.039TYPICAL SWITCH DIMENSIONSUB215SKG035C-1JC Bright Single Color LEDSuper Bright Single Color LED Single PoleDouble PoleUB225SKG03CF-1JB Bicolor LED Side ViewSingle Pole Double PoleUB226KKW016F-1JFSingle Color LED Side ViewSingle PoleDouble PoleUB216KKW01CF-1JB Bicolor LED Side View Single Pole Double PoleUB216KKW015F-1JF Single Color LED Side ViewSingle Pole Double PoleSeries UB2Low Profile PushbuttonsI n d i c a t o r sA c c e s s o r i e s S u p p l e m e n tT a c t i l e s K e y l o c k s R o t a r i e s P u s h b u t t o n sS l i d e sP r o g r a m m a b l T o g g l e sR o c k e r sT o u chT i l tAT4170 Opens 180°Closes automaticallySpring Loaded Protective Guard for Snap-in Mounting of PCB ModelProtective GuardPanelSwitchPC BoardInstallation 1 Install switch onto PC board.2 Snap protective guard into panel.3 Join the two(N) = Number of switches* Minimum dimension allows opening of cover to 180°OPTIONAL ACCESSORIESRecommended Panel Thickness:.039” ~ .126”(1.0mm ~ 3.2mm)Recommended Panel-to-PCB Range:.531” ~ .622”(13.5mm ~ 15.8mm)Materials:Cover: Clear PolycarbonateBase: Black Polyamide Coil Spring: Stainless SteelProtective Guard for Snap-in ModelAT4141Opens 90°Closes manuallyMaterials:Cover: Clear Polycarbonate Base: Black GFR PolyamideRecommended Panel Thickness:.039” ~ .106” (1.0mm ~ 2.7mm)WhenSeries UB2Low Profile PushbuttonsI n d i c a t o r sA c c e s s o r i e sS u p p l e m e n tT a c t i l e sK e y l o c k sR o t a r i e sP u s h b u t t o n sS l i d e s P r o g r a m m a b l R o c k e r s T o u c hT i l tT o g g l esOPTIONAL ACCESSORIESBarriers for Snap-in MountAT4143EndAT4144CenterMaterial: PolyamideCutouts for more than 1 Switch:A = .799” (20.3mm) x Number of Switches +.051” (1.3mm)Dust CoverAT4145 Not for use with barriers.Materials:Lid: Clear PVCOperating temperature range: 0°C ~ +70°C (32°F ~ 158°C).Gasket: PolyethyleneRecommended Panel Thickness .039” ~ .098” (1.0mm ~ 2.5mm)WhenSpring Loaded Protective Guard for Snap-in ModelAT4142Opens 180°Closes automaticallyMaterials:Cover: Clear Polycarbonate Base: Black GFR Polyamide Coil Spring: Stainless SteelRecommended Panel Thickness:.039” ~ .106” (1.0mm ~ 2.7mm)When分销商库存信息:NKK-SWITCHUB216SKW035F UB215KKW015F-1JF UB226SKG035F-1JB UB215KKW016CF-1JB UB215SKW036CF-1JB UB216KKW016CF-1JB UB226KKW016CF-2B UB226KKG016CF UB226SKW036CFUB226KKW016CF UB215KKW016CF-4J04UB216KKW016CF-4J04 UB215SKW036G UB215KKW016B UB215KKW016GUB215SKW036F UB215SKW036B UB216SKG036CF-4J04 UB215SKG036G UB215SKG036F UB216KKW016GUB215KKW016B-1JB UB215SKW036G-3JB UB25KKG016BUB225KKW016CF-4J02UB225KKW016CF-4J04UB225KKW016CF-4J01 UB225SKG036CF-4J02UB225SKG036CF-4J04UB226KKW016CF-4J02 UB226KKW016CF-4J04UB225KKW016F UB225SKW036FUB216KKW016G-1JB UB225KKW016F-1JB UB226SKG036CF-4J02 UB225SKG036B UB226SKG036B UB226SKW036FUB226KKW016F UB226KKW016G UB225SKG036B-3JB UB226KKG016F UB226SKG036G UB226SKG036B-3JB UB226KKG016F-3JB UB215KKW015C-1JB UB215KKW015C-1JC UB215KKW015D-1JD UB215KKW015F-1JB UB25KKW015CUB25KKW015D UB25KKW015F UB225KKW015C-1JB UB225KKW015C-1JC UB225KKW015D-1JB UB225KKW015F-1JB UB225KKW015F-1JF UB216KKW015C-1JB UB216KKW015C-1JC UB216KKW015D-1JB UB216KKW015D-1JD UB216KKW015F-1JB UB216KKW015F-1JF UB215SKW035F UB215SKW035CUB215KKW015C UB215KKW015D UB215KKW015FUB215SKG035C-1JC UB215SKG035D-1JB UB215SKG035D-1JD UB215SKG035F-1JB UB215SKG035F-1JF UB226KKW015C-1JB UB226KKW015C-1JC UB226KKW015D-1JD UB226KKW015F-1JB UB226KKW015F-1JF UB215KKG015C UB215SKG035CUB215SKG035D UB216SKG035C-1JB UB216SKG035C-1JC UB216SKG035D-1JB UB216SKG035D-1JD UB216SKG035F-1JB UB216SKG035F-1JF UB216KKW015F UB216KKW015CUB215KKW015D-1JB UB215SKW035D-1JB UB25KKW015C-JBUB215SKW035D UB216SKG035D UB216SKG035CUB216SKG035F UB215SKG035C-1JB UB215SKG035FUB225SKG035C-1JB UB225SKG035C-1JC UB225SKG035D-1JB UB225SKG035D-1JD UB225SKG035F-1JB UB225SKG035F-1JF UB215SKW035C-3JC UB215KKW015F-3JB UB215KKW015D-3JB UB215KKW015C-3JB UB215SKW035C-1JB UB215SKW035F-1JF UB215SKW035D-3JB UB215SKW035C-1JC UB215SKW035D-3JD UB215SKW035F-1JB UB216SKW035F-1JC UB225KKW015DUB225KKW015C UB215KKG015C-3JB UB215SKG035F-3JF UB215KKG015F-3JB UB215KKG015C-1JB UB215SKG035F-3JB。