瑞萨仿真器e1连接
瑞萨32位机 RX62T常见问题与解决办法

在100 MHz的频率下运行时,MCU仅消耗50mA的电流
●根据具体情况,可选择低功耗模式。
(休眠,所有模块停止,软件待机、深度软件待机)
[2012-3-29 10:51:59]
[问:cccfeb]
RX62T驱动电机的电路图有没有?有没有实例在网站上!
目前RX62T的产品实例还没有,客户基本上用H8/3062的老型号在做,如果能换成RX62T效果肯定明显,因为RX62T的性能比H8/3062高了很多.
[2012-3-29 10:51:57]
[问:liang-1011]
RX62T,32bitMCU的主要特点及优势?
[答:Kenwong]
增强型定时器(提高了PWM分辨率,带有比较器的启动定时器)
[答:tonyliu]
1.注意功率器件的选取。2.注意开关频率,通常开关频率越高,效率会有提高。
[2012-3-29 10:47:04]
[主持人:ChinaECNet]
各位网友,本次座谈的演示及问答内容,将于今天下午开始在中电网进行回放,同时还提供本次座谈的PPT内容下载,请大家关注中电网的更新。
[2012-3-29 10:47:52]
[2012-3-29 10:34:16]
[问:zpjnear]
请问光伏并网逆变器,光伏扬水逆变器,光伏微网逆变器中分别使用哪款MCU(Renesas)比较合适?
[答:Kenwong]
RX62T
[2012-3-29 10:34:44]
[问:ezcui]
在光伏逆变器上应用的单片机是否需有哪些严格或特殊的要求?
[2012-3-29 10:56:34]
E1传输线路常见故障处理方法

E1传输线路常见故障处理方法2M传输告警是在开局和维护过程中经常遇见告警之一,要能及时准确的处理这类告警,除了对2M传输线有清楚的认识外,还必须能将2M线原理准确的运用到告警的处理过程中。
一、E1(2M)电路从物理结构上看,E1传输设备的E1物理接头都是有2个,一收一发。
E1物理接头阻抗可分为75Ω和120Ω,75Ω常用有BNC和CC4这两种类型的接头,而120Ω只有RJ45接头。
75Ω的线材俗称同轴电缆,有双芯同轴线缆(SYV-75-2-2)和单芯同轴线缆(SYV-75-2-1)的两种,每根收线和发线实际上是由芯线和屏蔽线(或称地线回路)来连通。
要保证一个2M电路的正常连通,必须正确地连接线缆,同时要注意收发互相连通,有时候因为插头没插紧或插头不干净导致设备或E1线路故障。
设备之间通过E1线路连接以后,传送的信号的格式是PCM格式。
由于E1线路有传输距离的限制,连通距离较远的两设备中必须有采用光缆和其它技术的传输设备。
注:一般情况下,开局的时候从本端设备出来的2M线在到达DDF架时通过自环,都能在设备上看见状态,此时的状态为物理状态。
如果有的时候设备没有做数据,不能在软件上边实现状态的查看,则可以直接用二极管查看物理状态(以前在现场遇见过物理连接是正常的,但是二极管不发光,这个时候需要考虑更换二极管,因为有的二极管阻抗太大,而设备发出来的信号太弱,所以无法导致二极管发光。
但是这样的情况不多)二、常见告警分析收线上最常见到的故障情况有断线告警,全1码告警,帧失步告警,复帧失步告警等,其产生的原理和可能的原因如下:断线告警,一般是指不能从收线上收到有效的电平信号,或者不能收到任何信号。
产生的段落在离本端收线最近的一段同轴电缆上,一般是由于线断、接头焊接工艺不良等。
但要注意的是,当两端设备配合较好的情况下,同轴电缆的屏蔽线断开不会产生断线告警。
全1码告警,俗称上游告警。
一般是指本端能正常收到信号电平,而信号流中没有包含任何有用信息。
E1调试步骤

E1调试步骤1、记得让周成把徐汇苑拆卸下来的2651XM(连同BNC转RJ45的线缆、BNC双通!)一起带到虹桥上海城;2、电信放给用户的E1线路接口一般是BNC,思科路由器的E1卡一般是RJ45(其实真正叫RJ48),所以转接线一定不能少;3、E1模块一般有一代的单口子卡VWIC-1MFT-E1或双口子卡VWIC-2MFT-E1,二代的E1/T1二合一的单口子卡VWIC2-1MFT-T1/E1或双口子卡VWIC2-2MFT-T1/E1;4、这们这次是沿用用户原有的一块一代单口子卡VWIC-1MFT-E1。
它上面有三个指示灯,AL(告警灯),LP(环路灯),CD(数据灯)。
正常情况下,只有CD灯亮。
如果AL灯亮,说明从E1模块到电信对端这之间的线缆某处是断的。
5、一般调试E1模块时,需要和电信工程师对一下几个参数:*****************************************校验方式*:中国一般是NO-CRC4;信令标准*:电信一般叫30B+D、PRA、ETSI,其实和我们叫的PRI是同一信令;线路编码:Line Code。
电信一般值16,其实和我们的HDB3是一个值(16进制);ISDN Switch type:欧洲标准 primary-net5。
电信那边不用问,他们好像没有ISDN交换机类型这个说法。
*************************************************************** ********Router#sh controllers e1E1 1/0 is up.Applique type is Channelized E1 - balancedNo alarms detected.alarm-trigger is not setVersion info Firmware: 20040802, FPGA: 255, spm_count = 0 Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.6、线缆接通后,应该E1卡上只有CD灯亮。
E8E8a 仿真器用户手册附加文档

2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples.
封
RCJ10J0072-0100
E8/E8a 仿真器
用户手册附加8/38799F 时的注意事项
瑞萨单片机开发环境系统 H8 族 / H8/300H 超低功率系列
瑞萨软件使用教程

瑞萨工程建立教程(RL78 G13)依据瑞萨公司提供的视频编写RL78是低功耗16位的高性能系列MCU:1、3种超低功耗模式2、内核,三段流水线的CISC哈佛系统结构最短执行时间0.04167us/24MHz——1us/1MHz3、内置Flash(16K-512K)和DataFlash(4K-8K)4、丰富的外设功能:电源管理、DMA、CSI、UART10位ADC、IIC、IO 现在介绍R5F100LG,它对应的Flash如下表所示其引脚图如下:开发流程如图所示:瑞萨公司提供的开发板:工程建立工程:1、开发软件的安装:找到CubeSuitePlus_Package_V20000a软件,直接进行全信任的安装。
而另外两个软件:Microsoft Visual C++ 2010 SP1_x86和NET Framework 4_ x86_x64应该已经完全安装了,也可以再试着安装一下的(原来是旧版本的话)2、打开软件,在主界面中或者菜单栏里的projec中Create NEW project在出现的Create project对话框中,依次进行芯片选择,然后进行工程类型(项目、库、仿真)的选择、工程名、工程放置目录等设置。
3、在工程树种可以看到芯片的相关配置,然后在Code Generator中可以看到生成的代码,如果没有出现,则要在TOOL菜单中Plug-in Setting中的两个GODE选项都勾选中即可生成。
4、接着下面是配置和仿真工具的选择一定要注意Simulator是指软件仿真,如果选择此项会导致所连接的仿真器无现象了。
5、回到代码生成树目录里,第一项的Clock Generator有个感叹号,这里只是引脚映射没有设置好(一个引脚可以有多个功能选择),双击后在窗口里红色字的下面点击Fix setting完成默认设置。
接着一定要打开片上系统的选项:再根据速率要求,来设置时钟。
时钟后面部分默认设置了,6、到此,系统的必要条件基本满足了,接下来就进行代码生成:点击Generator Code生成代码然后在目录树中File下就可以看到生成的代码了。
R5-NE1远程I O通信模块规格书说明书

远程 I/O R5 系列通信模块机型: R5-NE1① ①在下列代码中选择。
(例如: R5-NE1/Q)・特殊规格 (例如: /C01)①附加代码◆特殊规格未填写:无特殊规格/Q:特殊规格(请从特殊规格之项另行选择)/C01: 硅涂层/C02: 聚氨酯涂层/C03: 橡胶涂层 IP地址可用组态软件进行设定。
可在本公司的网站上下载组态软件。
将本产品连接到电脑时,需要专用的连接电缆线。
所需专 用电缆线的型号请参照本公司网站的下载网站或组态软件 的使用说明书。
注)此软件的运作状况是在日文版与英文版OS上确认的。
・Ethernet: RJ-45接口・内部通信总线: 连接到底座 (机型: R5-BS) 上・内部电源: 由底座 (机型: R5-BS) 提供隔离: Ethernet-内部通信总线・内部电源间RUN显示灯: 红/绿2色LED通信正常时亮绿色灯;接收数据时亮红色灯(用DIP开关进行切换)ERR显示灯: 红/绿2色LED通信异常时绿色灯亮灯/闪烁;发送数据时,亮红色灯(用DIP开关进行切换)数据占有区设定: 用侧面的DIP开关设定占有区1或占有区2传输类型: 10BASE-T/100BASE-TX传输速度: 10/100Mbps (备有Auto Negotiation功能)通信协议: Modbus/TCP数据: RTU (二进制)通信链接数: 2个通信电缆线:・10BASE-T (STP电缆线Category 5)・100BASE-TX (STP电缆线Category 5e)最长节段: 100mIP地址: 可用组态软件 (机型: R5CON) 进行变更(初始值: 192.168.0.1)端口编号: 502Ethernet显示灯: LINK、DPLX、LINK10、LINK100、COL使用湿度范围: 30~90%RH (无冷凝)使用大气条件: 无腐蚀性气体和严重尘埃安装: 安装在底座 (机型: R5-BS) 上重量: 约100g隔离强度: Ethernet-内部通信总线・内部电源间1500V AC 1分钟电磁兼容指令(EMC指令) EMI EN 61000-6-4 EMS EN 61000-6-2RoHS指令注) 作为符合EU指令的产品使用时,要与Ver.2.00以上的电源模块 (机型: R5-PS) 一起使用。
Renesas推出E8片上调试仿真器

Renesas 推出E8 片上调试仿真器瑞萨科技公司(Renesas)宣布,开发出称作“E8仿真器”的低价格、片上调试仿真器*1,作为R8C/微型系列低管脚数、16 位微型计算机中R8C/14、R8C/15、R8C/16 和R8C/17 20 管脚产品组的开发工具。
在2004 年7 月30 日,将从日本开始样品发货。
这个仿真器继承了目前的低价格开发工具E7 仿真器的仿真功能和易用性。
E8 仿真器的性能总结如下。
(1)通过单线与仿真器通信,在接近实际操作的状态下进行调试通过单线进行R8C/14、R8C/15、R8C/16 或R8C/17 组微型计算机与E8 仿真器之间的通信,使用用户系统中未使用的管脚,可以在接近实际操作的状态下进行系统调试。
由于减少了调试用的管脚数,也减少了与调试有关的对系统电路设计的限制。
(2)以很低的成本提供多种有用的调试功能。
E8 仿真器以各个用户可以接受的价格提供,易于成批购买。
除了价格低外,E8 仿真器还具有很多有用的调试功能,也用作向微型计算机片上闪速存储器写入程序的闪存写入器,使其成为高成本效率的产品。
(3)尺寸紧凑、易于使用E8 仿真器保留了E7 仿真器紧凑的尺寸,其大小是97 mm ×65 mm ×22 mm。
可以使用兼容Windows®*2 的计算机作为主机,通过总线供电的USB(通用串行总线架构)连接。
由于尺寸紧凑,可以在很小的区域如桌面上,建立调试环境。
集成了HEW(高性能调试间)的开发环境用作用户接口,提供用户友好的环境,可以完成从编程到评价、验证的所有调试任务。
e1接口(t1接口用于本国)[精彩]
![e1接口(t1接口用于本国)[精彩]](https://img.taocdn.com/s3/m/391c4b5ae418964bcf84b9d528ea81c759f52e44.png)
E1接口(T1接口用于外国)T1、E1指中继线类型,即:用户的PBX连接到电信局的中继线类型。
T1主要应用于北美、欧洲、香港等地区我国使用E1中继。
E1的一个好处在于可以传送主叫的号码(ANI)E1可以同时传送30路通话,T1可以同时传送24路通话…………E1是欧洲标准,我国也使用这个标准,2048K;T1是北美标准,日本好像也是的,1544K。
在传输上用的非常的普遍。
E1最本来的用法是在用作语音交换机的数字中继时,是把一条E1作为32个64K来用,但是时隙0和时隙15是传输控制信令用,所以一条E1可以传30路话音。
这是在接入服务器上(如华为8010,北电的CVX1800等)说的E1,而和通常在路由器上说的E1概念有些不一样。
在路由器上的E1是不能划分时隙的,只能做2M线使用。
CE1的传输线路的带宽是2048K,它和E1的区别主要在于:E1不能划分时隙,CE1能划分时隙。
CE1的每个时隙是64K,一共有32个时隙,在使用的时候,可以划分为n*64K,例如:128K,256K等等。
CE1的0和15时隙是不用来传输用户的数据流量,0时隙是传送同步号,15时隙传送控制信令,这样实际能用的只有30个时隙,所以在具体配置CE1划分时隙时,要注意些了。
CE1 和E1 也可以互联,但是CE1必须当E1来使用,即不可分时隙使用。
因为CE1比较灵活,所以我们能常常碰到CE1。
1.一条E1是2.048M的链路,用PCM编码。
2.一个E1的帧长为256个bit,分为32个时隙,一个时隙为8个bit。
3.每秒有8k个E1的帧通过接口,即8K*256=2048kbps。
4.每个时隙在E1帧中占8bit,8*8k=64k,即一条E1中含有32个64K。
E1帧结构E1有成帧,成复帧与不成帧三种方式,在成帧的E1中第0时隙用于传输帧同步数据,其余31个时隙可以用于传输有效数据;在成复帧的E1中,除了第0时隙外,第16时隙是用于传输信令的,只有第1到15,第17到第31共30个时隙可用于传输有效数据;而在不成帧的E1中,所有32个时隙都可用于传输有效数据.一. E1基础知识E1信道的帧结构简述在E1信道中,8bit组成一个时隙(TS),由32个时隙组成了一个帧(F),16个帧组成一个复帧(MF)。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
R20UT0398CJ0200
User's Manual E1 仿真器 R0E000010KCE00 E20 仿真器 R0E000200KCT00
用户手册
本资料所记载的内容,均为本资料发行时的信息,瑞萨电子对于本资料所记载的产品或者 规格可能会作改动,恕不另行通知。 请通过瑞萨电子的主页确认发布的最新信息。Rev.2.002 Nhomakorabea11.02
Notice
Notice
1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm the latest product information with a Renesas Electronics sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. When exporting the products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. Renesas Electronics products are classified according to the following three quality grades: “Standard”, “High Quality”, and “Specific”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below. You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application categorized as “Specific” without the prior written consent of Renesas Electronics. Further, you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as “Specific” or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics. The quality grade of each Renesas Electronics product is “Standard” unless otherwise expressly specified in a Renesas Electronics data sheets or data books, etc. Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots. “High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anticrime systems; safety equipment; and medical equipment not specifically designed for life support. “Specific”: Aircraft; aerospace equipment; submersible repeaters; nuclear reactor control systems; medical equipment or systems for life support (e.g. artificial life support devices or systems), surgical implantations, or healthcare intervention (e.g. excision, etc.), and any other applications or purposes that pose a direct threat to human life. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written consent of Renesas Electronics. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. “Standard”: