2016科目二倒车入库技巧-98%通过率
Tait T800 Series II 电子产品说明书
Radio Systems Division, Tait Electronics LtdPage 1 of 16535 Wairakei Rd, P .O. Box 1645, Christchurch, New Zealand Phone: (64) (3) 358 3399 Fax: (64) (3) 358 2825Application Note AN-RSD-002Combining Third Party Equipment With The T800 Series II Radio Platform23 April 1998T800Any enquiries regarding this Application Note should be addressed in the first instance to your nearest approved Tait Dealer or Subsidiary . Further assistance may be obtained from the Cus-tomer Support Group, Radio Systems Division, Tait Electronics Ltd, Christchurch, New Zealand.IntroductionThis Application Note provides guidelines on combining third party equipment with the Tait T800 Series II radio platform. It shows pin inputs and outputs available on T800module and backplane D-range connectors and provides information on integrating third party equipment into a Tait rack frame, using the T800 ancillary chassis and rack frame guides.Third party equipment can be combined with Tait T800 Series II equipment in the fol-lowing ways.•You can interface equipment to T800 radio units via the D-range on individual modules (T800 receiver, transmitter/exciter, power supply), or via the back-plane PCB which interconnects the modules at the rear of the T800 rack frame.•You can integrate third party PCBs into a T800 rack frame by using a T800ancillary module chassis.This document is split into three main sections.•T800 Series II EquipmentGives guidelines for combining the Tait T800 Series II radio platform with third party equipment. It describes the standard Tait rack frame, the T800 radio mod-ules and location of the D-range on the modules and the backplane PCB (which is fitted to the rear of the rack frame).•T800 Series II Module Inputs And OutputsGives pin inputs and outputs for interfacing third party equipment with the T800 receiver, transmitter/exciter and power amplifier (PA), and the modules matching pin inputs and outputs on the backplane PCB.•Integrating Third Party PCBsGives specific dimensions for integrating third party PCBs into the ancillary chassis, and information on single, double and triple guide kits.AN-RSD-002T800 Series II EquipmentRack FrameThe T800-22-0000 is a standard 5U high, 19” wide base station/repeater rack frame. The rack frame can house the range of T800 Series II modules within the frequency range 66-960MHz, with power outputs ranging from 1-100W. Changing links on the back-plane PCB allows the Tait equipment in the rack frame to be configured as either a base station or a repeater.Figure 1 shows the mechanical layout of the T800-22-0000 rack frame. Modules slide into the rack frame along guides (single, double or triple) and can interface to third party equipment through the backplane PCB.Figure 1 Mechanical Layout Of The T800-22-0000 Rack FramePage 2 of 1623/04/98AN-RSD-002T800 Radio ModulesThird party equipment can be interfaced with the T800 receiver, transmitter/exciter or power amplifier through the 15-way D-range on the rear of the modules. An auxiliaryD-range (normally fitted as D-range 2) can be bought as an additional kit (T800-03-0000)for all modules except the PA. This provides you with additional D-range inputs and outputs. Typical uses of the T800-03-0000 are in paging, multichannel and remote con-trol applications and where external channel control is required.The D-range location on the module is shown in Figure 2. Available pin inputs and out-puts are described for the T800 receiver, transmitter/exciter and power amplifier mod-ules individually later in this document. Modules can be interfaced with the backplane PCB by way of the D-range sockets as shown on Figure 3.Space For OptionalD-range Plug(D-range 2)D-range Plug(D-range 1)Figure 2 D-range Location23/04/98Page 3 of 16AN-RSD-002Backplane PCBThe backplane PCB (T800-50-0000) has been laid out with OEM (Original Equipment Manufacturer) products in mind, and has sockets for the T800 module D-range. The PCB mounts across the rear panel of the rack frame guides, enabling a T800 Series II radio module to plug directly into the D-range sockets provided on the inner side of the PCB.The two 25-way D-ranges (shown enlarged in Figure 3) can be used to interface third party equipment, for example tone remote boards, with the T800-22-0000 rack frame. Most D-range inputs/outputs are made available on the two 25-way D-ranges (SK6 and SK7) and are described in following tables.25-way D-rangeSK725-way D-rangeSK6Figure 3 T800-50-0000 Backplane PCB Showing D-range LocationPage 4 of 1623/04/98AN-RSD-00223/04/98Page 5 of 16T800 Series II Module Inputs And OutputsReceiver : Standard Inputs And OutputsTable 1 shows standard inputs and outputs for the T800 receiver and corresponding inputs and outputs on the backplane PCB (SK7).Table 1 Standard Receiver Pin Inputs & OutputsNotes:DR1 = D-range 1 BKPL = Backplane.SignalDR1 PinBKPL (SK7)I/P O/PFunctionLine O/P1-41-4O/PAudio output from a 600Ω balanced line transformer. Output level adjustable from -50 to +10dBm via a potentiometer on the front panel. Pins 2 & 3 are usually linked for normal operation.RSSI 55O/PReceiver Strength Signal Indicator. Provides a DC voltage propor-tional to the signal strength of the received signal.Values are: VHF 4.5V @ -100dBm; 1V/15dB (-115 to -70dBm) UHF 2V @ -110dBm; 1V/10dB (-115 to -70dBm). For UHF, optional board must be fitted.Audio 166O/PAudio 1 allows access to audio before it passes through the squelch circuitry . The output will provide frequencies down to 5Hz when the audio processor is linked for flat response. From Audio 1, audio can be passed to external CTCSS and signalling decoders.Serial Com/Audio 277I/OSerial programming input for programming the module. Can be configured as Audio 2 by internal link resistors if required. Audio 2 is an input and when used in conjunction with Audio 1 allows the audio path to be broken so that external audio processing can be used.Speaker 819O/P Provides up to 1W into a 4Ω speaker.Supply V oltage 9-10-I/P DC Supply V oltage input. Nominal 13.8V , can operate from 10.8 to 16V DC.Gate O/P1114O/PPulls low when a signal is received. In a repeater, configuration can be used to key the transmitter by directly connecting it to the Tx Key pin.Receiver Gate Relay12131516O/PRelay CommonRelay Normally OpenA normally open relay contact that closes when a signal is received. The relay will only operate when PL270 is linked.Ground 14-15-I/P Power supply earth, negative ground.Backplane SK7123456789101112131415Receiver D-range 1Page 6 of 1623/04/98AN-RSD-002Receiver : Additional Inputs And OutputsTable 2 shows additional inputs and outputs for the T800 receiver and corresponding inputs and outputs on the backplane PCB (SK6).Table 2 Additional Receiver Pin Inputs & OutputsNotes :DR2 = D-range 2 BKPL = BackplaneSignalDR2 PinBKPL (SK6)I/P O/PFunctionChannel 1 22Select 0-6 2 9 3 214 8 I/P5 2067 7 19External channel select pins (including Channel Select 7 on pin 11). Normally high, these pins are pulled low to select logic 0. To select a channel the binary equivalent must be applied to the pins. when all pins are left floating (i.e. high) then the selected channel is deter-mined by software (PGM800Win).Note: When using external channel selection, pin 11 must be pulled low.Ground 86I/P Power supply earth, negative ground.Rx Disable 918I/PWhen pulled low disables receiver audio output. Usually used in a base station application to ensure there is no interference when the transmitter is operating.CTCSS Disable 105I/P Disables CTCSS (Continuous Tone Controlled Squelch System).Channel Select 71123I/P Function as for other channel select lines. Must be pulled low when using external channel selection.Serial Comm1224I/OSerial programming input for programming the module. Can be used if it is not possible to program the radio from D-range 1.Aux-Out 13 150-2 14 10 O/P 15 11Open drain type; capable of sinking 2.25mA via 2k2Ω; V ds max.=5V . Logic state can change when the channel is er definable by using PGM800Win software.Backplane SK6Receiver D-range 2123456789101112131415AN-RSD-00223/04/98Page 7 of 16Transmitter/Exciter : Standard Inputs And OutputsTable 3 shows standard inputs and outputs for the T800 transmitter/exciter and corre-sponding inputs and outputs on the backplane PCB (SK7).Table 3 Standard Transmitter/Exciter Pin Inputs & OutputsNotes :DR1 = D-range 1 BKPL = Backplane.SignalDR1 PinBKPL (SK7)I/P O/PFunctionLine I/P 1-422-25I/PAudio input to a 600Ω balanced line transformer. For an unbalanced line connect the line I/P 4 to ground. Accepts audio levels as low as -30 dBm. Pins 2 & 3 are usually linked for normal operation.Tx Enable 521O/P Pulls low when the transmitter is keyed. Usually connected directly to Tx Key on the PA to activate the PA alarm circuitry .Audio 2620I/PAudio 2 allows audio to be input to the audio processor bypassing the 600Ω line transformer. Ideal place to re-inject audio such as a voice scrambler after external processing.Serial Com/Audio 177I/O O/PSerial programming input for programming the module. Can be configured as Audio 1 by internal link resistors if required. Audio 1 allows access to the audio directly after the 600Ω line transformer. When used in conjunction with Audio 2 it allows the audio path to be broken so that external audio processing can be used.CTCSS 818I/P An external input for CTCSS or DCS (Digital Coded Squelch). Supply V oltage 9-10-I/P DC Supply V oltage input. Nominal 13.8V , can operate from 10.8 to 16V DC.Opto Keys 11 (+)12 (-)98I/PA high isolation keying option. A DC voltage between 6V and 50V applied to these inputs will key the transmitter. The inputs may be used to key the transmitter via a DC remote.Tx Key 1317I/P A high impedance input which is pulled low to key the transmitter. Must be <0.7V or connected directly to Ground.Ground14-15-I/PPower supply earth, negative groundBackplane SK7T ransmitter/Exciter D-range 1123456789101112131415Page 8 of 1623/04/98AN-RSD-002Transmitter/Exciter : Additional Inputs And OutputsTable 4 shows the additional pin inputs and outputs for the T800 transmitter/exciter and corresponding inputs and outputs on the backplane PCB (SK6).Table 4 Additional Transmitter/Exciter Pin Inputs & OutputsNotes :DR2 = D-range 2 BKPL = Backplane.SignalDR2 Pin BKPL (SK6)I/P O/PFunctionChannel 1 22Select 0-6 2 9 3 214 8 I/P5 2067 7 19External channel select pins (including Channel Select 7 on pin 11). Normally high, these pins are pulled low to select logic 0. To select a channel the binary equivalent must be applied to the pins. When all pins are left floating (i.e. high) then the selected channel is deter-mined by software (PGM800Win).Note: When using external channel selection, pin 11 must be pulled low.Ground 86I/P Power supply earth, negative ground.Tx Relay Drive 918I/P Used for coaxial relay switching. Pulls to ground when the transmit-ter is keyed.CTCSS Disable 1017I/P Disables CTCSS (Continuous Tone Controlled Squelch System).Channel Select 71123I/P Function as for other channel select lines. Must be pulled low when using external channel selection.Serial Comm1224I/OSerial programming input for programming the module. Can be used if it is not possible to program the radio from D-range 1.Aux-Out 13 160-2 14 4 O/P 15 3Open drain type; capable of sinking 2.25mA via 2k2Ω; V ds max.=5V . Logic state can change when the channel is er definable by using PGM800Win software.Backplane SK6123456789101112131415T ransmitter/Exciter D-range 2AN-RSD-00223/04/98Page 9 of 16Power Amplifier : Standard Inputs And OutputsThe location of the D-range on the T800 PA is shown on the diagram below. Available pin inputs and outputs for the PA are shown on Table 5.Table 5 Power Amplifier Pin Inputs & OutputsSignal DR1 PinBKPL (SK7)I/P O/PFunctionSupply V oltage1-2-I/P DC Supply V oltage input. Nominal 13.8V , can operate from 10.8V to 16V DC. Connected to pins 9, 10 and 11.Forward Power Alarm 310O/PThese are normally low and float if forward power drops below, or reverse power rises above, pre-set limits. They have a 500mA sink capability . A signal is only provided when the Tx Key line on the PA is being pulled low.Reverse Power Alarm 411O/PForward Power Metering 512O/PV oltage outputs proportional to the levels of forward and reverse power are available at these pins for metering purposes. There is enough output to drive a coil meter.Reverse Power Metering613O/PGround 7-8-I/P Power supply earth, negative ground. Connected to pins 13, 14 and 15.Supply V oltge9-11-I/P Function as for Pins 1 and 2.Tx Key1221I/P Keys the PA when ground is applied. This line is usually taken to the Tx Enable line on the Exciter.Ground13-15-O/PPower supply earth, negative earth.123456789101112131415D-range ConnectorP A D-rangeBackplane SK7Page 10 of 1623/04/98AN-RSD-002Integrating Third Party PCBsThis section gives guidelines on integrating third party PCBs with Tait equipment using the T800 ancillary module chassis and rack frame guides.There are two types of PCB which will fit into the T800 ancillary module chassis, a pri-mary PCB and a front panel PCB.Primary PCBYou can fit the primary PCB into the body of the T800 ancillary module chassis by slid-ing it along one of the grooves (the grooves are shown in the diagram of the chassis,Figure 7). PCBs can be fitted into any of the three grooves in the chassis.Third party PCBs must be made to specific dimensions to ensure they integrate with the T800 ancillary module chassis. The dimensions of the main PCB are shown in Figure 4.All measurements are shown in millimetres.The grey shaded area represents the part of the PCB where components are unplaceable as it is the area at the edge of the PCB covered by the chassis. This is a 3mm wide area.The black area represents the part of the PCB where components should be of a restricted height. The maximum height for components in this area is 3.2mm. The maxi-mum component height for the rest of the PCB area is 42mm. The length of the primary PCB is 260mm, but longer PCBs can be fitted if a front panel PCB is not required.Figure 4 Main PCB DimensionsLocation Of Pin 1 D-range 1Figure 5 shows the footprint and spacing dimensions of the 15-way double D-range connector. The location of pin 1 on both D-range 1 and D-range 2 is also shown. All dimensions are shown in millimetres.Figure 5 D-range Connector DimensionsPin 1 Of D-range 2Pin 1 Of D-range 1∅ 1.1∅ 3.2Front Panel PCBFigure 6 below shows the dimensions necessary for a third party PCB to fit behind the front panel of the ancillary chassis. All measurements are shown in millimetres. The maximum height of components on this PCB is 8mm.The PCB fits in behind the front panel and is screwed to a sub-chassis panel using M3x8 Pan Torx Taptite screws. The T800 ancillary module chassis is shown in Figure 7.Figure 6 Front Panel PCB DimensionsAncillary Module ChassisThe mechanical design of the T800-08-0000 ancillary module chassis is shown in Figure 7. Third party PCBs can be fitted into the chassis, either as a primary PCB (shown in Figure 4) or as a smaller PCB which fits behind the front panel (shown in Figure 6).The primary PCB slides into a groove in the T800 ancillary module chassis and the front panel PCB screws in behind the front panel using the sub-chassis panel (shown in Figure 7).The T800 ancillary module chassis is held in the rack frame by the rack frame guides. The rack frame guides are described on following pages.15-WayDouble D-rangeConnectorPrimary PCB Slides Into GrooveFront Panel PCB Screws InUsing Sub-Chassis PanelFigure 7 T800-08-0000 Ancillary Module ChassisAll parts shown on Figure 7 excluding the PCBs are included in the T800 ancillary mod-ule chassis kit.T800-41-0001 - Single Guide KitThe T800-41-0001 rack frame guide shown in Figure 8 is designed to fit into the T800Series II rack frame (T800-22-0000). The single guide accepts the T800-08-0000 ancillary chassis or a T800 Series II module (except for power supplies and power amplifiers which must use their own guides).The single guide kit is supplied disassembled and comprises a top and bottom rail, a rear panel, two D-range sockets and mounting screws.Figure 8 T800-41-0001 Single GuideRack Mounting HolesAperture For RF ConnectorsSlots For D-range ConnectorsRack Mounting Hole sOptional Backplane PCB Mounts On Rear Of GuideRack Mounting HoleFront Panel Mounting HolesT800-41-0002 - Double Guide KitThe T800-41-0002 rack frame guide shown in Figure 9 is designed to fit into the T800Series II rack frame (T800-22-0000). The double guide accepts any combination of the T800-08-0000 ancillary chassis and T800 Series II modules (except for power supplies and power amplifiers which must use their own guides).The double guide kit is supplied disassembled and comprises two top and bottom rails,a double width rear panel, four D-range sockets and mounting screws.Figure 9 T800-41-0002 Double GuideFront Panel Mounting HolesRack Mounting HolesRack Mounting HolesRack Mounting HolesSlots For D-Range ConnectorsRack Mounting HolesAperture For RF ConnectorsOptional Backplane PCB Mounts On Rear Of GuideT800-41-0003 - Triple Guide KitThe T800-41-0003 rack frame guide shown in Figure 10 is designed to fit into the T800Series II rack frame (T800-22-0000). The triple guide accepts any combination of the T800-08-0000 ancillary chassis and T800 Series II modules (except for power supplies and power amplifiers which must use their own guides).The triple guide kit is supplied disassembled and comprises three top and bottom rails,a triple width rear panel, six D-range sockets and mounting screws.Figure 10 T800-41-0003 Triple GuideFront Panel Mounting HolesRack Mounting HolesRack Mounting HolesOptional Backplane PCB Mounts On Rear Of GuideRack Mounting HolesAperture For RF ConnectorsRack Mounting HolesSlots For D-range Connectors。
玩转Chinajoy尽享游戏乐趣___e-Play特别推荐助你畅玩热门网游
利刃重铸 荣耀出击罗技G400利刃重铸MX518玩家典藏版 达成《光荣使命》116罗技Logitech G400 利刃重铸MX518玩家典藏版在今年ChinaJoy现场，罗技与当下备受关注的中国首款军事游戏《光荣使命》强强联手，展出了“G400利刃重铸MX518玩家典藏版”游戏鼠标。
经典复刻MX518炫酷造型，更多配置性能升级，唤起众多游戏老鸟们的经典回忆，那些记忆中与哥们死党一起战斗、熬夜、比赛的日日夜夜，因为有了MX518陪伴而变得如此珍贵。
而今，G400玩家典藏版全新上市相信会重新燃气新一轮的战争激情。
小编也有幸体验到了这款备受关注的G400玩家典藏版，不得不说，沿袭经典的银色凹凸不平弹壳效果喷涂外壳，给人以颇具迷惑力的立体视觉感受。
持握使用时，反而感受是顺滑和称手的操作体验，鼠标够长，足以给手腕支持力，加上最高3600dpi、1000次/秒的响应速度、人体工学设计的支持，使得在一些特殊环境下，罗技G400玩家典藏版的使用可谓得心应手。
如今FPS游戏大肆风靡，作为首款大型军事网游《光荣使命》更是将FPS游戏推向新一代热潮。
《光荣使命》由南京军区授权开发制作，国内率先达成英伟达认证体系下支持DirectX11 的自主研发网游。
而罗技G400玩家典藏版的加入，让玩家体验到更加逼真的军营战地生活和枪战氛围。
当然，小编得到最新消息，这款鼠标的《光荣使命》纪念版将在8月1日建军节在京东商城独家首发。
除了充满军旅色彩的特殊包装G400玩家典藏版之外，豪华纪念版内还将包括《光荣使命》军用单机版 、士兵身份牌/民用网络版封测权限、班长强军人物形象、主题鼠标垫（限量5000只）、迷彩水壶腰包（限量1000只）等价值数百元的游戏实物和虚拟礼品，支持FPS游戏，又喜欢罗技经典鼠标MX518的同学，可以行动啦!400~3600 DPI高级光学传感器，滚轮上下方随时可调的4档DPI设定，游戏中瞬间切换、精确瞄准，抢占先机1000次/秒的响应速度，8倍于普通USB鼠标，助你游戏中快速做出反应，避免坐失良机推荐理由：罗技G400利刃重铸MX518性能更强 价格不变专为FPS游戏而生ChinaJoy现场表现卓越，备受关注与今夏热门军事题材网游《光荣使命》强强合作推出豪华套包Copyright©博看网 . All Rights Reserved.117数字族e文章作者：e-Play编辑组责任编辑：九言我们本期《数字e族》，正好赶上e-Play全体人马赶赴ChinaJoy盛会之时，自然也是会响应一下读者们的要求：最近有不少读者来询问小编们，大意是暑假到了，大作不断，我需要更换新的配置或者外设，我们本期也会根据一些产品，为大家推荐一些性价比高或颇为拉风的硬件产品，九言也是征求了诸位小编的意见，精心整理，诸位上眼了！这款鼠标运用赛睿最新的2.4GHz 无线技术，激光传感最高CPI达8200，同时还如同上一代延续了“幸运11号”的概念，支持11个可无限定义的宏按键，同时配合配送软件，可以自由地通过拖拽方式定义《魔兽世界》的技能到自定义按键上。
年度最佳RTS选手Fly100%(陆维梁)
龙源期刊网
年度最佳RTS选手Fly100%（陆维梁）
作者：
来源：《电子竞技》2016年第01期
十年前，Sky第一次夺得WCG世界冠军，让中国War3逐渐走向全盛。
十年后，堪称电竞项目常青树的War3迎来了一个小阳春。
2015年魔兽3比赛回暖。
大到年度盛典WCA，小到每周一次凤凰杯，还有网易黄金赛、PGL和ESCC，林林总总，给魔兽3爱好者带来了视觉盛宴，更给坚持奋战第一线的魔兽3选手们带来的丰厚奖金。
年末盘点，刚猛兽王Fly100%拿下超过40万元人民币奖金，雄踞魔兽选手第一。
尤其是在众星云集的WCA，Fly激战四天夺冠。
这个冠军的成色足以让本年度所有冠军黯然失色。
Fly先是小组赛连克老冤家Infi、TH000，后又马失前蹄输给yAws进入败者组。
在败者组，兽王爆发血性杀了回来。
决赛面对yAws，Fly让二追三，以最完美最刺激的姿势完成了复仇。
这个WCA冠军，让我们不仅想起当年Fly的豪言壮语：“就算是WCG不在了，就算是打铁拳，我也要拿下世界冠军！”
2015年，Fly就是世界冠军！。
湖南省历年一本投档线(详细)
1307 1401 1403 1411 1412 1501 2101 2102 2103 2105 2107 2108 2109 2111 2121 2124 2129 2162 2201 2202 2204 2215 2301 2302 2303 2305 2306 2316 3101 3102 3103 3104 3105 3106 3107 3108 3109 3110 3116 3122 3123 3126 3170 3201 3202 3203
东北大学秦皇岛分校 太原理工大学 山西大学 中北大学 山西医科大学 内蒙古大学 东北大学 大连理工大学 大连海事大学 辽宁大学 沈阳药科大学 东北财经大学 辽宁工程技术大学 中国医科大学 沈阳农业大学 沈阳工业大学 大连医科大学 大连理工大学(盘锦校区) 吉林大学 延边大学 东北师范大学 长春理工大学 哈尔滨工业大学 哈尔滨工程大学 东北农业大学 东北林业大学 东北石油大学 哈尔滨医科大学 复旦大学 上海交通大学 东华大学 同济大学 华东理工大学 华东师范大学 上海外国语大学 复旦大学医学院 上海财经大学 上海大学 华东政法大学 上海海事大学 上海对外经贸大学 上海理工大学 上海交通大学医学院 南京大学 东南大学 中国矿业大学
547 554 559 516 540 531 553 543 516 509 522 513 495 549 527 551 516 517 629 533 522 533 522 500 632 530 542 508 595 547 520 540 508 549 498 496 567 553 549 534 536 516 526 504 515 517 589
4202 4203 4208 4209 4210 4212 4215 4216 4224 4226 4227 4238 4247 4301 4302 4303 4304 4305 4306 4307 4308 4309 4311 4312 4350 4401 4402 4403 4404 4407 4408 4410 4411 4412 4426 4427 4428 4435 4501 4511 4603 4800 4855 4884 5001 5002 5003
Top Polymer 2011
Hydraulic hose，Transmission belt. etc. Wires/cables，Bolster of railway sleeper, Elevator sideway etc. Soundproof gear、Parts of electrical equipment.etc.
Typical Grades
T.P.E.顶塑企业
Incoming quality control We always choose the first-brand raw material suppliers by assessing their commitment to quality and environment, Kuraray, Kraton, Asahii
Typical grades
Test Item Grades 5313-651Z 5313-701Z 5313-751Z 5313-801Z 5313-851Z 5313-901Z Tensile strength (kgf/cm2) 26 29 31 38 52.6 61
Hardness Shore A 65 ShoreA 68 ShoreA 75 ShoreA 80 ShoreA 85 ShoreA 90
T.P.E.顶塑企业
Foreign market
Argentina, Peru, Australia, Vietnam, Thailand……
T.P.E.顶塑企业
Full range of products
Topolymer® 3000s 4000s 5000s 6000s 8000s 9000s Ms 3200, 3211, 3236 4001, 4002, 4003 5313 6200, 6211, 6236, 6261
射击项目成绩创造者比赛名称日期地点
马来西亚
10米移动靶30+30
588环
杨 凌
第四十八届世界锦标赛
2002年04月01日
芬兰拉蒂
决赛
687.9环
杨 凌
世界杯赛
1996年06月06日
米 兰
团体
1730环
云南队（曾国斌、胡志丹、文明亮）
全国射击系列赛（第二站）
2004年05月21日
杭州
10米移动靶20+20
393环
决赛
479环
最低成绩标准
业余组[女子]
小口径标准步枪3×20
581环
祁美杨子
全国青少年射击比赛
2002年08月18日
黄石
决赛
683.9环
祁美杨子
全国青少年射击比赛
2002年08月18日
黄石
小口径标准步枪卧射60发
593环
祁美杨子
全国青少年射击比赛
2002年08月18日
黄石
决赛
691环
最低成绩标准
气步枪40发
胡 斌 渊
全国射击系列赛（第一站）
1999年04月17日
上海
145中
胡 斌 渊
全国射击系列赛（第二站）
2003年07月20日
郑州
决赛
192中
胡 斌 渊
全国射击系列赛（第三站）
1999年10月12日
广东东莞
团 体
415中
中 国 队（张冰、李勃、张永杰）
亚洲飞碟锦标赛
1995年07月08日
成 都
成年[女子]
运动步枪卧射60发
600环
田 红
中国、伊朗射击友谊赛
生产相关统计趋势图
31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31
1085
31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31 31
备 注
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35
720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720 720
2012年 一 季度设备利用率、完好率统计汇总表
序 号 设备编号
P-01 P-02 P-03 P-04 P-05 P-06 P-07 P-08 K-01 K-02 H-01 H-02 F-01 F-02 F-03 F-04 F-05 Q-01 Q-02 Q-03 Q-04 Q-05 Q-06 H-03 D-01 K-03 K-04 B-01 C-01 C-02 L-01 L-02 L-03 L-04 L-05 XCLP1-120 XCLP1-160 XCLP1-160 XCLP1-160 XCLP1-160 H-06 POD-15A POD-15A POD-15A POD-15A
应运数
2016年里约奥运会中国银牌获得者
【杜丽◎女子10米气步枪◎第1银】【里约奥运会◎杜丽】离子重追探梦达，女王连射画环加。
四朝元老圆新路，彩退安平乐百家。
【孙杨◎男子400米自由泳◎第2银】【里约奥运会◎孙杨】功败垂成差秒求，头埋肩打咽伤抽。
泪流满面言声痛，风雨同行伴作舟。
【徐嘉余◎男子100米仰泳◎第3银】【里约奥运会◎徐嘉余】藏拙力赴隐军随，强作游雷破水推。
忆锁银添冲雾散，拨云见日盼明辉。
【吕小军◎男子77公斤级◎第4银】【里约奥运会◎吕小军】同台力举冠谁居，数载尘封破里昔。
无愧万人心待望，疑来笑解露风迷。
【李晓霞◎乒乓球女子单打◎第5银】【里约奥运会◎李晓霞】晚霞戏做女豪杰，八面威风赞口皆。
金榜题名扬四海，心联竖拇探头学。
【张彬彬◎女子50米步枪三姿◎第6银】【里约奥运会◎张彬彬】双彬双木快人先，初露锋芒造手尖。
三秀三姿流水射，箭如针指命心环。
【许安琪、孙玉洁、孙一文、郝佳露◎女子团体重剑◎第7银】【里约奥运会◎许安琪】势均力斗毅决消，惜败尤荣换友牢。
默道难关心渡累，怀颜知己忘年交。
【里约奥运会◎孙玉洁】双亲忍痛报平安，满念心头比技尖。
三色奖牌追耀载，联鸣二老露辛含。
【里约奥运会◎孙一文】花容月貌艳文霞，痛刺锥心起站夹。
摘取头盔湿润水，强埋披苦笑千家。
【里约奥运会◎郝佳露】替赴一文错把责，失之交臂冠随罗。
心怀愧疚加声泪，梦指天鸣曲路多。
【张继科◎乒乓球男子单打◎第8银】【里约奥运会◎张继科】寒心消志付前空，花落谁家会冠龙。
累数三局求胜晚，心神交瘁唤休从。
【蔡泽林◎男子20公里竞走◎第9银】【里约奥运会◎蔡泽林】寡言少语入沙厅，举动牵心寄故朋。
身落五星披桂冠，一朝天地保乡荣。
【田涛◎男子85公斤级◎第10银】【里约奥运会◎田涛】中青小将露锋芒，抓把惜失料盼忙。
风雨飘摇凭意起，屈居一亚展名扬。
【董栋◎男子蹦床◎第11银】【里约奥运会◎董栋】阳颜倾洒笑心笛，曲诉三朝苦乐移。
身手不凡床动舞，福花艳捧四方迷。
【陈佩娜◎女子帆板RS:X◎第12银】【里约奥运会◎陈佩娜】待风消小错追攻，一点明标尽力冲。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
2016科目二倒车入库技巧，98%通过率
文/裸食煮义（小编的驾照正在实习期所以就写了本文）
这个月底有个朋友准备考驾照的科目二，她说好担心，很紧张，还说有好多同学都挂。
我在安慰完一轮后，问了下她，自我感觉学得怎样，她回答：“感觉还好，但是好多同学都是在练的时候感觉还好，一测试就挂了。
”
科目二考不过是很正常的，毕竟只有一小部分人像小编这么运气好——所有科目一次性通过。
主要是因为从科目二开始后面的每一项驾考测试都是有固定的学员通过率区间的，意思也就是每次测试必须至少挂那么一些人。
后面在安慰我朋友的过程中发现：现在的驾校教练也太不负责任了。
我朋友说她教练没有教过她，每次上车练车都是她的同学教她，她听她的同学说，她们教练不太会教人，跟其他教练不一样（只知道是肇庆四会的某教练）。
当听到这里的时候，我才明白为什么她会紧张测试，如果这样练习科目二，测试的时候还不紧张，那最后肯定是我或者以后走在大街上认识我那朋友的人紧张。
我以前考驾照的时候教练虽谈不上非常好，但是他教的各种方法我个人觉得是非常好的，而且每次他给我们讲的方法，都是他和驾校的其他教练一起实践测试过的，最后还能用通俗易懂的表达让我们当时的初学者一听就会。
科目二难点很多，挂在这一关的人也不计其数，其中倒在侧方位、倒车入库的人位居榜首。
现在我就给大家详细的介绍下倒车入库的方法技巧，广东肇庆那边测试的车子可能会比我照片中的小轿车个头大，不过没有关系，其中的红色标注、节点等地方都可以一样使用过去。
这是正在考驾照的你真正需要的:2016科目二倒车入库技巧，98%通过
一、准备工作
1、上车后，先调整好座椅的前后位置，靠背也调整到舒适的角度，以保证能自由的转动方向盘和看到车头的引擎盖为最佳。
2、调整左右后视镜，使镜中车身出现在镜子约1/3位置，后门把手在镜子上沿露出。
调整左右后视镜
调整左右后视镜
二、右出库
挂一档，带正车头，直线出库。
当车头引擎盖刚刚盖住库对面边线时，向右打死方向盘。
提示：每个人身高不同，要根据自己情况找准合适的参考点。
右出库
当车身和左边线平行时，回正方向盘，继续前行，车头跨越感应线。
此时车身和左边线距离恰巧在最佳距离以内，这样才能保证后面的入库不会轧线。
提示：可反复调整上一步右打死的时间点，确保车身在最佳距离以内。
最佳距离
三、右入库
开始缓慢倒车，向左扭头，观察左车窗外感应线的位置，当感应线和车窗下沿的交点到达A点时，向右打死方向盘。
提示：A点为第一个关键点，每个人看到的位置会稍有不同，大家可以根据实际情况适当提前或延迟少许。
右入库倒车
保持方向盘右打死，继续倒车，同时观察右后视镜，这个过程镜中的状态是这样变化的：看不到库角→看到库角→库角和车身的距离逐渐缩小，库角也从上到下不断下沉。
提示：当库角和车身距离相当于一支水笔的粗细时，到达第二个关键点，记为B点，此时迅速回正方向盘。
B点知识
继续倒车，右后视镜中的库角也继续下沉，当库角刚好消失时，迅速向右打死方向盘。
注意：这是第三个关键点，记为C点。
这个关键点不仅考察眼力，更考验反应速度，切记，一定要在库角刚好消失时迅速向右打死方向盘！
倒车
继续倒车，当车身和库线平行时，回正方向盘。
提示：此时，车速要慢，不要看左后视镜，始终观测右后视镜，适时修正车身和库线距离。
距离宽了向右稍打方向盘，反之则向左。
休正时间不要过长，否则将影响下一步。
看左后视镜
继续缓慢倒车，迅速扭头看左后视镜，当左后视镜下沿刚好盖住左出库线时，踩刹车，停住。
这个位置停车能保证汽车在库中的前后距离刚好合适，每个人可适当修正，但一定要记清修正后的观测点！
右入库
从外部观察，此时车身前后预留距离刚刚合适，不会扫到前后的红外线。
右入库
而右边距离应稍稍窄于左侧，在倒进来修正距离时保证右距稍窄一点就可以了。
右入库
四、左出库和左入库
挂一档，带正车头，直线出库。
当车头引擎盖刚刚盖住库对面边线时，向左打死方向盘。
左出库和左入库
当车身和左出库线平行后，继续前进，直到车头向左倾斜，并且跨过左感应线，这时再踩刹车，停住。
提示：整个过程，方向盘都是左打死状态。
当车停住后，右手换左手握紧方向盘，右手去将一档换成倒档。
换完档，左手仍换回右手握紧方向盘，开始倒车。
左出库和左入库
继续保持方向盘左打死状态，车速放慢，始终观察左后视镜。
在镜中看到的情况是：先是看到左库线→左库角→整个库口→车身入库。
这时判断车身和左库线是否平行，一旦平行，立即回正方向盘，继续缓慢倒车。
左出库和左入库
当左后视镜下沿刚好盖住左出库线时，踩刹车，停住。
这个位置停车能保证汽车在库中的前后距离刚好合适。
左出库和左入库
祝我的朋友科目二测试顺利通过，希望也对其他考驾照的朋友有帮助。