IP4283CZ10

Symbol
Parameter
Conditions
VBRzd ILRzd VF Cch(TMDS) ∆Cch(TMDS) Cch(mutual)
Rdyn
Zener diode breakdown voltage
I = 1 mA
Zener diode reverse leakage current per TMDS channel; V = 3.0 V
Conditions
Min
Max
Unit
VI
input voltage
Vesd
electrostatic discharge voltage all pins to ground;
IEC 61000-4-2, level 4;
contact discharge
GND − 0.5 +5.5
V
−8
+8
kV
IP4283CZ10_1
Product data sheet
Rev. 01 — 7 May 2009
© NXP B.V. 2009. All rights reserved.
4 of 10
NXP Semiconductors
IP4283CZ10
ESD protection for ultra high-speed interfaces
3 of 10
NXP Semiconductors
IP4283CZ10
ESD protection for ultra high-speed interfaces
6. Application information
The IP4283CZ10 is designed mainly to provide high-level ESD protection for high-speed serial data buses such as HDMI, DisplayPort, eSATA and LVDS data lines.
Type number
Package
Name
IP4283CZ10-TB XSON10U
IP4283CZ10-TT TSSOP10
Description
plastic extremely thin small outline package; no leads; 10 terminals; UTLP based; body 1 × 2.5 × 0.5 mm plastic thin shrink small outline package; 10 leads; body width 3 mm
NXP Semiconductors
IP4283CZ10
ESD protection for ultra high-speed interfaces
2. Pinning information
Table 1. Pinning Pin Symbol 1 TMDS_CH1−
2 TMDS_CH1+
3 GND 4 TMDS_CH2−
[1] This parameter is guaranteed by design. [2] Human Body Model according to JESD22-A-J114D. [3] According to IEC 61000-4-5/9.
Min Typ Max Unit
6- 9V
- - 1 µA
1.2 Features
I Pb-free, RoHS compliant and free of Halogen and Antimony (Dark Green compliant) I System ESD protection for HDMI, DisplayPort, eSATA and LVDS I All signal lines with integrated rail-to-rail clamping diodes for downstream ESD
protection of ±8 kV according to IEC 61000-4-2, level 4 I Matched 0.5 mm trace spacing I Signal lines with ≤ 0.05 pF matching capacitance between signal pairs I Line capacitance of only 0.6 pF for each channel I 4-channel, UTLP10 or TSSOP10 Pb-free package I HDMI 1.3a compliant I DisplayPort compliant I Design-friendly ‘pass-thru’ signal routing
TMDS_GND TMDS_D0−
TMDS_CLK+
HDMI
CONNECTOR
TMDS_GND
TMDS_CLK−
CEC
n.c.
DDC_CLK
DDC_DAT
GND +5 V HOT PLUG DETECTION
6 54
IP4221CZ6 1 23
100 nF
001aaj793
Fig 1. Application diagram of HDMI ESD protection using IP4283CZ10-TB
- 0.7 - V
[1] -
0.6 -
pF
[1] -
0.05 -
pF
[1] -
0.07 -
pF
[3]
- 2.4 - Ω
- 1.3 - Ω
[2] -
8-
V
IP4283CZ10_1
Product data sheet
Rev. 01 — 7 May 2009
© NXP B.V. 2009. All rights reserved.
Simplified outline
1
10
2
9
3
8
4
7
5
6
Transparent top view
XSON10U
3. Ordering information
Graphic symbol
10612 Nhomakorabea45
1
5
TSSOP10
3, 8 001aai619
Table 2. Ordering information
dynamic resistance
I = 1 A; Tamb = 25 °C
positive transient
negative transient
VCL(ch)trt(pos) positive transient channel clamping voltage
Vesd = 8 kV HBM; Tamb = 25 °C
IP4283CZ10
ESD protection for ultra high-speed interfaces
Rev. 01 — 7 May 2009
Product data sheet
1. Product profile
1.1 General description
The IP4283CZ10 is designed to protect high-speed interfaces such as HDMI, DisplayPort, eSATA and LVDS against ElectroStatic Discharge (ESD). The device includes high-level ESD protection diodes for ultra high-speed signal lines and is available in two package variants: UTLP10 and TSSOP10.
Version SOT1059-1
SOT552-1
4. Limiting values
Table 3. Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol Parameter
2 of 10
NXP Semiconductors
IP4283CZ10
ESD protection for ultra high-speed interfaces
5. Characteristics
Table 4. Characteristics Tamb = 25 °C unless otherwise specified.
It is recommended that when designing the printed-circuit board, careful consideration is given to impedance matching, and signal coupling.
A basic application diagram for the ESD protection of an HDMI interface is shown in Figure 1 and Figure 2 for package versions TB and TT respectively.
5 TMDS_CH2+
6 n.c. 7 n.c. 8 GND 9 n.c. 10 n.c.
Description negative channel 1 ESD protection positive channel 1 ESD protection ground negative channel 2 ESD protection positive channel 2 ESD protection not connected not connected ground not connected not connected