常用公制螺纹量规尺寸标准对照表(NEW)
最新GB公制螺纹标准资料
普通螺纹标准规格表螺纹基本知识一、螺纹的名词术语螺纹：在圆柱或圆锥表面上，沿着螺旋线所形成的具有规定牙型的连续凸起。
圆柱螺纹/圆锥螺纹；外螺纹/内螺纹；右旋螺纹/左旋螺纹。
右旋螺纹：顺时针旋转时选入的螺纹。
左旋螺纹：逆时针旋转时选入的螺纹。
完整螺纹：牙顶和牙底具有完整形状的螺纹。
不完整螺纹：牙底完整而牙顶不完整的螺纹。
螺尾：向光滑表面过渡的牙底不完整的螺纹。
有效螺纹：由完整螺纹和不完整螺纹组成的螺纹，不包括螺尾。
公称直径：代表螺纹尺寸的直径。
大径：外螺纹的顶径、内螺纹的底径。
小径：外螺纹的底径、内螺纹的顶径。
中径：一个假想圆柱或圆锥的直径，该圆柱或圆锥的母线通过牙型上沟槽和凸起宽度相等的地方。
单一中径：牙型上沟槽宽度等于1/2基本螺距的地方。
作用中径：在规定的旋合长度内，恰好包容实际螺纹的一个假想螺纹的中径，这个假想螺纹具有理想的螺距、螺纹半角、及牙型高度，并在牙顶和牙底留有间隙，不与实际螺纹大、小径发生干涉。
牙型角：在螺纹牙型上，两相邻牙侧间的夹角。
螺距：相邻两牙在中径线上对应两点间的轴向距离。
螺纹精度：由螺纹公差带和旋合长度共同组成的衡量螺纹质量的综合指标。
二、.螺纹概述一般将螺纹分为圆柱螺纹和圆锥螺纹。
（一）圆柱螺纹1. 普通螺纹（又称米制或公制螺纹）螺纹代号M，牙形角60°，基本牙形为平顶。
精度等级：内螺纹4~8级，外螺纹3~9级。
2. 美标统一螺纹（又称60°英制螺纹）螺纹代号UNC、UNF、UNEF、UN、UNS，牙形角60°，基本牙形为平顶。
精度等级：内螺纹1B~3B，外螺纹1A~3A。
3. 非螺纹密封的管螺纹（又称圆柱管螺纹）螺纹代号G，牙形角55°，基本牙形为圆顶圆底。
精度等级：内螺纹标准级和D级，外螺纹A、B级。
4. 梯形螺纹螺纹代号Tr，牙形角30°（美标为29°），基本牙形为平顶平底。
精度等级：7~9级，（美标为2G~6G）。
常用公制螺纹环规尺寸标准对照表.pdf
尺寸偏差±T PL 尺寸偏差±T PL /2磨损下限尺寸M1.4 1.4 1.2050.260.300.002####0.0070.00950.0075 1.4020.0070 1.20720.0035 1.1977 1.349M1.7 1.7 1.4730.30.3500.006####0.0090.01250.0095 1.7060.0090 1.47870.0045 1.4662 1.638M22 1.7400.350.400.006####0.0090.01250.0095 2.0060.0090 1.74620.0045 1.7337 1.921M2.5 2.5 2.2080.390.4500.006####0.0090.01250.0095 2.5060.0090 2.21370.0045 2.2012 2.405M2.6 2.6 2.3080.390.4500.006####0.0090.01250.0095 2.6060.0090 2.31370.0045 2.3012 2.505M33 2.6750.430.500.006####0.0090.01250.0095 3.0060.0090 2.68130.0045 2.6688 2.888M44 3.5450.610.700.006####0.0090.01250.0095 4.0060.0090 3.55140.0045 3.5389 3.819M4*0.54 3.6750.430.500.006####0.0090.01250.0095 4.0060.0090 3.68130.0045 3.6688 3.888M55 4.4800.690.800.006####0.0090.01250.0095 5.0060.0090 4.48640.0045 4.4739 4.783M5*0.55 4.6750.430.500.006####0.0090.01250.0095 5.0060.0090 4.68130.0045 4.6688 4.888M66 5.3510.87100.012####0.0110.01750.0115 6.0120.0110 5.36250.0055 5.3450 5.723M6*0.756 5.5130.650.7500.012####0.0110.01750.0115 6.0120.0110 5.52490.0055 5.5074 5.813M7*0.757 6.5130.650.7500.012####0.0110.01750.01157.0120.0110 6.52490.0055 6.5074 6.813M887.188 1.08 1.2500.012####0.0110.01750.01158.0120.01107.20010.00557.18267.624M8*0.587.6750.430.500.006####0.0090.01250.00958.0060.00907.68130.00457.66887.900M8*0.7587.5130.650.7500.012####0.0110.01750.01158.0120.01107.52490.00557.50747.813M8*187.3510.87100.012####0.0110.01750.01158.0120.01107.36250.00557.34507.723M9*0.598.6750.430.500.006####0.0090.01250.00959.0060.00908.68130.00458.66888.900W GOW NGHPEIZ PLTD 2T PL通规Ｔ大径D+EI+Z PL 中径D 2+EI+Z PL大径D 2+EI+TD 2+T PL /2+2F 1螺纹规格（6H ）公称尺寸D 中径尺寸D 2尺寸偏差±T PL尺寸偏差±T PL/2磨损下限尺寸W GO W NG H P EI Z PL TD2T PL通规Ｔ大径D+EI+Z PL中径D2+EI+Z PL大径D2+EI+TD2+T PL/2+2F1螺纹规格（6H）公称尺寸D中径尺寸D2M10109.026 1.3 1.500.012####0.0110.01750.011510.0120.01109.03780.00559.02039.536 M10*0.5109.6750.430.500.006####0.0090.01250.009510.0060.00909.68130.00459.66889.900 M10*0.75109.5130.650.7500.012####0.0110.01750.011510.0120.01109.52490.00559.50749.813 M10*1109.3510.87100.012####0.0110.01750.011510.0120.01109.36250.00559.34509.723 M10*1.25109.188 1.08 1.2500.012####0.0110.01750.011510.0120.01109.20010.00559.18269.624 M121210.863 1.52 1.7500.012####0.0110.01750.011512.0120.011010.87540.005510.857911.448 M12*0.51211.6750.430.500.006####0.0090.01250.009512.0060.009011.68130.004511.668811.906 M12*11211.3510.87100.012####0.0110.01750.011512.0120.011011.36250.005511.345011.733 M12*1.51211.026 1.3 1.500.012####0.0110.01750.011512.0120.011011.03780.005511.020311.546 M141412.701 1.73200.016####0.0140.01750.011514.0160.014012.71700.007012.699513.353 M14*11413.3510.87100.012####0.0110.01750.011514.0120.011013.36250.005513.345013.733 M14*1.251413.188 1.08 1.2500.012####0.0110.01750.011514.0120.011013.20010.005513.182613.644 M14*1.51413.026 1.3 1.500.012####0.0110.01750.011514.0120.011013.03780.005513.020313.546 M14*21412.701 1.73200.016####0.0140.0210.01514.0160.014012.71700.007012.696013.353 M15*0.51514.6750.430.500.006####0.0090.01250.009515.0060.009014.68130.004514.668814.906 M15*11514.3510.87100.012####0.0110.01750.011515.0120.011014.36250.005514.345014.733 M161614.701 1.73200.016####0.0140.0210.01516.0160.014014.71700.007014.696015.353 M16*0.51615.6750.430.500.006####0.0090.01250.009516.0060.009015.68130.004515.668815.906尺寸偏差±T PL尺寸偏差±T PL/2磨损下限尺寸W GO W NG H P EI Z PL TD2T PL通规Ｔ大径D+EI+Z PL中径D2+EI+Z PL大径D2+EI+TD2+T PL/2+2F1螺纹规格（6H）公称尺寸D中径尺寸D2M16*1.51615.026 1.3 1.500.012####0.0110.01750.011516.0120.011015.03780.005515.020315.546 M18*0.51817.6750.430.500.006####0.0090.01250.009518.0060.009017.68130.004517.668817.906 M18*11817.3510.87100.012####0.0110.01750.011518.0120.011017.36250.005517.345017.733 M18*21816.701 1.73200.016####0.0140.0210.01518.0160.014016.71700.007016.696017.353 M20*0.52019.6750.430.500.006####0.0090.01250.009520.0060.009019.68130.004519.668819.906 M20*12019.3510.87100.012####0.0110.01750.011520.0120.011019.36250.005519.345019.733 M20*1.52019.026 1.3 1.500.012####0.0110.01750.011520.0120.011019.03780.005519.020319.546 M22*0.52221.6750.430.500.006####0.0090.01250.009522.0060.009021.68130.004521.668821.906 M22*12221.3510.87100.012####0.0110.01750.011522.0120.011021.36250.005521.345021.733 M22*1.52221.026 1.3 1.500.012####0.0110.01750.011522.0120.011021.03780.005521.020321.546 M24*12423.3510.87100.012####0.0110.01750.011524.0120.011023.36250.005523.345023.743 M24*1.52423.026 1.3 1.500.012####0.0110.01750.011524.0120.011023.03780.005523.020323.556 M25*1.52524.026 1.3 1.500.012####0.0110.01750.011525.0120.011024.03780.005524.020324.556 M26*1.52625.026 1.3 1.500.012####0.0110.01750.011526.0120.011025.03780.005525.020325.556 M30*0.753029.5130.650.7500.012####0.0110.01750.011530.0120.011029.52490.005529.507429.831 M30*13029.3510.87100.012####0.0110.01750.011530.0120.011029.36250.005529.345029.743 M30*1.53029.026 1.3 1.500.012####0.0110.01750.011530.0120.011029.03780.005529.020329.556 M30*23028.701 1.73200.016####0.0140.0210.01530.0160.014028.71700.007028.696029.365尺寸偏差±T PL尺寸偏差±T PL/2磨损下限尺寸W GO W NG H P EI Z PL TD2T PL通规Ｔ大径D+EI+Z PL中径D2+EI+Z PL大径D2+EI+TD2+T PL/2+2F1螺纹规格（6H）公称尺寸D中径尺寸D2M33*1.53332.026 1.3 1.500.012####0.0110.01750.011533.0120.011032.03780.005532.020332.556 M35*1.53534.026 1.3 1.500.012####0.0110.01750.011535.0120.011034.03780.005534.020334.556 M36*1.53635.026 1.3 1.500.012####0.0110.01750.011536.0120.011035.03780.005535.020335.556 M42*24240.701 1.73200.016####0.0140.0210.01542.0160.014040.71700.007040.696041.365 M45*1.54544.026 1.3 1.500.012####0.0110.01750.011545.0120.011044.03780.005544.020344.556 M50*1.55049.026 1.3 1.500.016####0.0140.0210.01550.0160.014049.04180.007049.020849.570 M52*35250.052 2.6300.016####0.0140.0210.01552.0160.014050.06750.007050.046550.988 M58*1.55857.026 1.3 1.500.016####0.0140.0210.01558.0160.014057.04180.007057.020857.570 M64*16463.3510.87100.012####0.0110.01750.011564.0120.011063.36250.005563.345063.753偏差±T PL 尺寸偏差±T PL /2磨损下限0.0070 1.28370.0035 1.27620.0090 1.56220.0045 1.55270.0090 1.83470.0045 1.82520.0090 2.30720.0045 2.29770.0090 2.40720.0045 2.39770.0090 2.77980.0045 2.77030.0090 3.66790.0045 3.65840.0090 3.77980.0045 3.77030.0090 4.60990.0045 4.60040.0090 4.77980.0045 4.77030.0110 5.50600.0055 5.49450.0110 5.65040.0055 5.63890.0110 6.65040.0055 6.63890.01107.35360.00557.34210.00907.79180.00457.78230.01107.65040.00557.63890.01107.50600.00557.49450.00908.79180.00458.7823止规Ｚ大径EI+TD 2+T PL /2+2F 1中径D 2+EI+TD 2+T PL /2偏差±T PL尺寸偏差±T PL/2磨损下限止规Ｚ大径EI+TD2+T PL/2+2F1中径D2+EI+TD2+T PL/20.01109.21130.00559.1998 0.00909.79180.00459.7823 0.01109.65040.00559.6389 0.01109.50600.00559.4945 0.01109.35360.00559.3421 0.011011.06890.005511.0574 0.009011.79780.004511.7883 0.011011.51600.005511.5045 0.011011.22130.005511.2098 0.014012.92000.007012.9085 0.011013.51600.005513.5045 0.011013.37360.005513.3621 0.011013.22130.005513.2098 0.014012.92000.007012.9050 0.009014.79780.004514.7883 0.011014.51600.005514.5045 0.014014.92000.007014.9050 0.009015.79780.004515.7883偏差±T PL尺寸偏差±T PL/2磨损下限止规Ｚ大径EI+TD2+T PL/2+2F1中径D2+EI+TD2+T PL/20.011015.22130.005515.2098 0.009017.79780.004517.7883 0.011017.51600.005517.5045 0.014016.92000.007016.9050 0.009019.79780.004519.7883 0.011019.51600.005519.5045 0.011019.22130.005519.2098 0.009021.79780.004521.7883 0.011021.51600.005521.5045 0.011021.22130.005521.2098 0.011023.52600.005523.5145 0.011023.23130.005523.2198 0.011024.23130.005524.2198 0.011025.23130.005525.2198 0.011029.66840.005529.6569 0.011029.52600.005529.5145 0.011029.23130.005529.2198 0.014028.93200.007028.9170偏差±T PL尺寸偏差±T PL/2磨损下限止规Ｚ大径EI+TD2+T PL/2+2F1中径D2+EI+TD2+T PL/20.011032.23130.005532.2198 0.011034.23130.005534.2198 0.011035.23130.005535.2198 0.014040.93200.007040.9170 0.011044.23130.005544.2198 0.014049.24480.007049.2298 0.014050.33850.007050.3235 0.014057.24480.007057.2298 0.011063.53600.005563.5245。
(完整版)最新GB公制螺纹标准
普通螺纹标准规格表螺纹基本知识一、螺纹的名词术语螺纹：在圆柱或圆锥表面上，沿着螺旋线所形成的具有规定牙型的连续凸起。
圆柱螺纹/圆锥螺纹；外螺纹/内螺纹；右旋螺纹/左旋螺纹。
右旋螺纹：顺时针旋转时选入的螺纹。
左旋螺纹：逆时针旋转时选入的螺纹。
完整螺纹：牙顶和牙底具有完整形状的螺纹。
不完整螺纹：牙底完整而牙顶不完整的螺纹。
螺尾：向光滑表面过渡的牙底不完整的螺纹。
有效螺纹：由完整螺纹和不完整螺纹组成的螺纹，不包括螺尾。
公称直径：代表螺纹尺寸的直径。
大径：外螺纹的顶径、内螺纹的底径。
小径：外螺纹的底径、内螺纹的顶径。
中径：一个假想圆柱或圆锥的直径，该圆柱或圆锥的母线通过牙型上沟槽和凸起宽度相等的地方。
单一中径：牙型上沟槽宽度等于1/2基本螺距的地方。
作用中径：在规定的旋合长度内，恰好包容实际螺纹的一个假想螺纹的中径，这个假想螺纹具有理想的螺距、螺纹半角、及牙型高度，并在牙顶和牙底留有间隙，不与实际螺纹大、小径发生干涉。
牙型角：在螺纹牙型上，两相邻牙侧间的夹角。
螺距：相邻两牙在中径线上对应两点间的轴向距离。
螺纹精度：由螺纹公差带和旋合长度共同组成的衡量螺纹质量的综合指标。
二、.螺纹概述一般将螺纹分为圆柱螺纹和圆锥螺纹。
（一）圆柱螺纹1. 普通螺纹（又称米制或公制螺纹）螺纹代号M，牙形角60°，基本牙形为平顶。
精度等级：内螺纹4~8级，外螺纹3~9级。
2. 美标统一螺纹（又称60°英制螺纹）螺纹代号UNC、UNF、UNEF、UN、UNS，牙形角60°，基本牙形为平顶。
精度等级：内螺纹1B~3B，外螺纹1A~3A。
3. 非螺纹密封的管螺纹（又称圆柱管螺纹）螺纹代号G，牙形角55°，基本牙形为圆顶圆底。
精度等级：内螺纹标准级和D级，外螺纹A、B级。
4. 梯形螺纹螺纹代号Tr，牙形角30°（美标为29°），基本牙形为平顶平底。
精度等级：7~9级，（美标为2G~6G）。
常用公制螺纹环规尺寸标准对照表(20200804230709).pdf
尺寸偏差±T PL 尺寸偏差±T PL /2磨损下限尺寸M1.4 1.4 1.2050.260.300.002####0.0070.00950.0075 1.4020.0070 1.20720.0035 1.1977 1.349M1.7 1.7 1.4730.30.3500.006####0.0090.01250.0095 1.7060.0090 1.47870.0045 1.4662 1.638M22 1.7400.350.400.006####0.0090.01250.0095 2.0060.0090 1.74620.0045 1.7337 1.921M2.5 2.5 2.2080.390.4500.006####0.0090.01250.0095 2.5060.0090 2.21370.0045 2.2012 2.405M2.6 2.6 2.3080.390.4500.006####0.0090.01250.0095 2.6060.0090 2.31370.0045 2.3012 2.505M33 2.6750.430.500.006####0.0090.01250.0095 3.0060.0090 2.68130.0045 2.6688 2.888M44 3.5450.610.700.006####0.0090.01250.0095 4.0060.0090 3.55140.0045 3.5389 3.819M4*0.54 3.6750.430.500.006####0.0090.01250.0095 4.0060.0090 3.68130.0045 3.6688 3.888M55 4.4800.690.800.006####0.0090.01250.0095 5.0060.0090 4.48640.0045 4.4739 4.783M5*0.55 4.6750.430.500.006####0.0090.01250.0095 5.0060.0090 4.68130.0045 4.6688 4.888M66 5.3510.87100.012####0.0110.01750.0115 6.0120.0110 5.36250.0055 5.3450 5.723M6*0.756 5.5130.650.7500.012####0.0110.01750.0115 6.0120.0110 5.52490.0055 5.5074 5.813M7*0.757 6.5130.650.7500.012####0.0110.01750.01157.0120.0110 6.52490.0055 6.5074 6.813M887.188 1.08 1.2500.012####0.0110.01750.01158.0120.01107.20010.00557.18267.624M8*0.587.6750.430.500.006####0.0090.01250.00958.0060.00907.68130.00457.66887.900M8*0.7587.5130.650.7500.012####0.0110.01750.01158.0120.01107.52490.00557.50747.813M8*187.3510.87100.012####0.0110.01750.01158.0120.01107.36250.00557.34507.723M9*0.598.6750.430.500.006####0.0090.01250.00959.0060.00908.68130.00458.66888.900W GOW NGHPEIZ PLTD 2T PL通规Ｔ大径D+EI+Z PL 中径D 2+EI+Z PL大径D 2+EI+TD 2+T PL /2+2F 1螺纹规格（6H ）公称尺寸D 中径尺寸D 2尺寸偏差±T PL尺寸偏差±T PL/2磨损下限尺寸W GO W NG H P EI Z PL TD2T PL通规Ｔ大径D+EI+Z PL中径D2+EI+Z PL大径D2+EI+TD2+T PL/2+2F1螺纹规格（6H）公称尺寸D中径尺寸D2M10109.026 1.3 1.500.012####0.0110.01750.011510.0120.01109.03780.00559.02039.536 M10*0.5109.6750.430.500.006####0.0090.01250.009510.0060.00909.68130.00459.66889.900 M10*0.75109.5130.650.7500.012####0.0110.01750.011510.0120.01109.52490.00559.50749.813 M10*1109.3510.87100.012####0.0110.01750.011510.0120.01109.36250.00559.34509.723 M10*1.25109.188 1.08 1.2500.012####0.0110.01750.011510.0120.01109.20010.00559.18269.624 M121210.863 1.52 1.7500.012####0.0110.01750.011512.0120.011010.87540.005510.857911.448 M12*0.51211.6750.430.500.006####0.0090.01250.009512.0060.009011.68130.004511.668811.906 M12*11211.3510.87100.012####0.0110.01750.011512.0120.011011.36250.005511.345011.733 M12*1.51211.026 1.3 1.500.012####0.0110.01750.011512.0120.011011.03780.005511.020311.546 M141412.701 1.73200.016####0.0140.01750.011514.0160.014012.71700.007012.699513.353 M14*11413.3510.87100.012####0.0110.01750.011514.0120.011013.36250.005513.345013.733 M14*1.251413.188 1.08 1.2500.012####0.0110.01750.011514.0120.011013.20010.005513.182613.644 M14*1.51413.026 1.3 1.500.012####0.0110.01750.011514.0120.011013.03780.005513.020313.546 M14*21412.701 1.73200.016####0.0140.0210.01514.0160.014012.71700.007012.696013.353 M15*0.51514.6750.430.500.006####0.0090.01250.009515.0060.009014.68130.004514.668814.906 M15*11514.3510.87100.012####0.0110.01750.011515.0120.011014.36250.005514.345014.733 M161614.701 1.73200.016####0.0140.0210.01516.0160.014014.71700.007014.696015.353 M16*0.51615.6750.430.500.006####0.0090.01250.009516.0060.009015.68130.004515.668815.906尺寸偏差±T PL尺寸偏差±T PL/2磨损下限尺寸W GO W NG H P EI Z PL TD2T PL通规Ｔ大径D+EI+Z PL中径D2+EI+Z PL大径D2+EI+TD2+T PL/2+2F1螺纹规格（6H）公称尺寸D中径尺寸D2M16*1.51615.026 1.3 1.500.012####0.0110.01750.011516.0120.011015.03780.005515.020315.546 M18*0.51817.6750.430.500.006####0.0090.01250.009518.0060.009017.68130.004517.668817.906 M18*11817.3510.87100.012####0.0110.01750.011518.0120.011017.36250.005517.345017.733 M18*21816.701 1.73200.016####0.0140.0210.01518.0160.014016.71700.007016.696017.353 M20*0.52019.6750.430.500.006####0.0090.01250.009520.0060.009019.68130.004519.668819.906 M20*12019.3510.87100.012####0.0110.01750.011520.0120.011019.36250.005519.345019.733 M20*1.52019.026 1.3 1.500.012####0.0110.01750.011520.0120.011019.03780.005519.020319.546 M22*0.52221.6750.430.500.006####0.0090.01250.009522.0060.009021.68130.004521.668821.906 M22*12221.3510.87100.012####0.0110.01750.011522.0120.011021.36250.005521.345021.733 M22*1.52221.026 1.3 1.500.012####0.0110.01750.011522.0120.011021.03780.005521.020321.546 M24*12423.3510.87100.012####0.0110.01750.011524.0120.011023.36250.005523.345023.743 M24*1.52423.026 1.3 1.500.012####0.0110.01750.011524.0120.011023.03780.005523.020323.556 M25*1.52524.026 1.3 1.500.012####0.0110.01750.011525.0120.011024.03780.005524.020324.556 M26*1.52625.026 1.3 1.500.012####0.0110.01750.011526.0120.011025.03780.005525.020325.556 M30*0.753029.5130.650.7500.012####0.0110.01750.011530.0120.011029.52490.005529.507429.831 M30*13029.3510.87100.012####0.0110.01750.011530.0120.011029.36250.005529.345029.743 M30*1.53029.026 1.3 1.500.012####0.0110.01750.011530.0120.011029.03780.005529.020329.556 M30*23028.701 1.73200.016####0.0140.0210.01530.0160.014028.71700.007028.696029.365尺寸偏差±T PL尺寸偏差±T PL/2磨损下限尺寸W GO W NG H P EI Z PL TD2T PL通规Ｔ大径D+EI+Z PL中径D2+EI+Z PL大径D2+EI+TD2+T PL/2+2F1螺纹规格（6H）公称尺寸D中径尺寸D2M33*1.53332.026 1.3 1.500.012####0.0110.01750.011533.0120.011032.03780.005532.020332.556 M35*1.53534.026 1.3 1.500.012####0.0110.01750.011535.0120.011034.03780.005534.020334.556 M36*1.53635.026 1.3 1.500.012####0.0110.01750.011536.0120.011035.03780.005535.020335.556 M42*24240.701 1.73200.016####0.0140.0210.01542.0160.014040.71700.007040.696041.365 M45*1.54544.026 1.3 1.500.012####0.0110.01750.011545.0120.011044.03780.005544.020344.556 M50*1.55049.026 1.3 1.500.016####0.0140.0210.01550.0160.014049.04180.007049.020849.570 M52*35250.052 2.6300.016####0.0140.0210.01552.0160.014050.06750.007050.046550.988 M58*1.55857.026 1.3 1.500.016####0.0140.0210.01558.0160.014057.04180.007057.020857.570 M64*16463.3510.87100.012####0.0110.01750.011564.0120.011063.36250.005563.345063.753偏差±T PL 尺寸偏差±T PL /2磨损下限0.0070 1.28370.0035 1.27620.0090 1.56220.0045 1.55270.0090 1.83470.0045 1.82520.0090 2.30720.0045 2.29770.0090 2.40720.0045 2.39770.0090 2.77980.0045 2.77030.0090 3.66790.0045 3.65840.0090 3.77980.0045 3.77030.0090 4.60990.0045 4.60040.0090 4.77980.0045 4.77030.0110 5.50600.0055 5.49450.0110 5.65040.0055 5.63890.0110 6.65040.0055 6.63890.01107.35360.00557.34210.00907.79180.00457.78230.01107.65040.00557.63890.01107.50600.00557.49450.00908.79180.00458.7823止规Ｚ大径EI+TD 2+T PL /2+2F 1中径D 2+EI+TD 2+T PL /2偏差±T PL尺寸偏差±T PL/2磨损下限止规Ｚ大径EI+TD2+T PL/2+2F1中径D2+EI+TD2+T PL/20.01109.21130.00559.1998 0.00909.79180.00459.7823 0.01109.65040.00559.6389 0.01109.50600.00559.4945 0.01109.35360.00559.3421 0.011011.06890.005511.0574 0.009011.79780.004511.7883 0.011011.51600.005511.5045 0.011011.22130.005511.2098 0.014012.92000.007012.9085 0.011013.51600.005513.5045 0.011013.37360.005513.3621 0.011013.22130.005513.2098 0.014012.92000.007012.9050 0.009014.79780.004514.7883 0.011014.51600.005514.5045 0.014014.92000.007014.9050 0.009015.79780.004515.7883偏差±T PL尺寸偏差±T PL/2磨损下限止规Ｚ大径EI+TD2+T PL/2+2F1中径D2+EI+TD2+T PL/20.011015.22130.005515.2098 0.009017.79780.004517.7883 0.011017.51600.005517.5045 0.014016.92000.007016.9050 0.009019.79780.004519.7883 0.011019.51600.005519.5045 0.011019.22130.005519.2098 0.009021.79780.004521.7883 0.011021.51600.005521.5045 0.011021.22130.005521.2098 0.011023.52600.005523.5145 0.011023.23130.005523.2198 0.011024.23130.005524.2198 0.011025.23130.005525.2198 0.011029.66840.005529.6569 0.011029.52600.005529.5145 0.011029.23130.005529.2198 0.014028.93200.007028.9170偏差±T PL尺寸偏差±T PL/2磨损下限止规Ｚ大径EI+TD2+T PL/2+2F1中径D2+EI+TD2+T PL/20.011032.23130.005532.2198 0.011034.23130.005534.2198 0.011035.23130.005535.2198 0.014040.93200.007040.9170 0.011044.23130.005544.2198 0.014049.24480.007049.2298 0.014050.33850.007050.3235 0.014057.24480.007057.2298 0.011063.53600.005563.5245。
最新GB公制螺纹标准
最新GB公制螺纹标准普通螺纹标准规格表普通螺纹基本尺寸（mm）普通螺纹基本尺寸（mm）公称直径螺距p 中径小径公称直径螺距p 中径小径1 0.25 0.838 0.729 22 1.5 21.026 20.3761.2 0.25 1.038 0.929 222.5 20.376 19.2941.4 0.3 1.205 1.075 24 2 22.701 21.8351.6 0.35 1.373 1.221 24 3 22.051 20.7522 0.4 1.740 1.567 27 2 25.701 24.8352.5 0.45 2.208 2.013 27 3 25.051 23.7523 0.5 2.675 2.459 30 2 28.701 27.8353.5 0.6 3.110 2.850 30 3.5 27.727 26.2114 0.7 3.545 3.242 33 2 31.701 30.8354.5 0.75 4.013 3.688 33 3.5 30.727 29.2115 0.8 4.480 4.134 36 3 34.051 32.7526 1 5.350 4.917 36 4 33.042 31.6708 1 7.350 6.917 39 3 37.051 35.7528 1.25 7.188 6.647 39 4 36.042 34.67010 1 9.350 8.917 42 3 40.051 38.75210 1.25 9.188 8.647 42 4.5 39.077 37.12910 1.5 9.026 8.376 45 3 43.051 41.75212 1.25 11.188 10.647 45 4.5 42.077 40.12912 1.5 11.026 10.376 48 3 46.051 44.75212 1.75 10.863 10.106 48 5 44.752 42.58714 1.5 13.026 12.376 52 4 49.402 47.67014 2 12.701 11.835 52 5 48.752 46.58716 1.5 15.026 14.376 58 4 53.402 51.67016 2 14.701 13.835 58 4.5 52.428 50.04618 2.5 16.376 15.294 60 4 57.402 55.67020 1.5 19.026 18.376 60 5.5 56.428 54.04620 2 18.701 17.835 64 4 61.402 59.67020 2.5 18.376 17.294 64 6 60.103 57.505螺纹基本知识一、螺纹的名词术语螺纹：在圆柱或圆锥表面上，沿着螺旋线所形成的具有规定牙型的连续凸起。
公制螺纹尺寸表[1]
![公制螺纹尺寸表[1]](https://img.taocdn.com/s3/m/84f100733868011ca300a6c30c2259010302f350.png)
公制螺纹尺寸表是用于描述不同公称直径和螺距的普通螺纹尺寸的表格。这些尺寸通常用于描述和规定机械设备的连接和固定，以下是公制螺纹尺寸表：
1.公称直径（mm）与螺距（P）：
公称直径
螺距
ห้องสมุดไป่ตู้0.2
0.7
0.25
0.75
0.3
0.75
0.4
1.0
0.5
1.0
0.6
1.0
0.8
1.25
1.0
1.25
1.25
1.25
1.5
1.5
1.75
1.5
2.0
1.5/1.75/2.0，按ISO/DIN3 标准选择其中一个尺寸，按国标（GB）标准选择另外一个尺寸。如果螺母中不含有保持力层，则需另加丝锥和套筒，则不使用这个尺寸系列。
以上尺寸只供参考，实际使用中可能因应具体情况有所差异。另外，具体选择公制螺纹尺寸应结合实际情况与设备规格，参考有关工程标准及使用手册，选择合适公称直径与螺距。
最新GB公制螺纹标准
普通螺纹标准规格表螺纹基本知识一、螺纹的名词术语螺纹：在圆柱或圆锥表面上，沿着螺旋线所形成的具有规定牙型的连续凸起。
圆柱螺纹/圆锥螺纹；外螺纹/内螺纹；右旋螺纹/左旋螺纹。
右旋螺纹：顺时针旋转时选入的螺纹。
左旋螺纹：逆时针旋转时选入的螺纹。
完整螺纹：牙顶和牙底具有完整形状的螺纹。
不完整螺纹：牙底完整而牙顶不完整的螺纹。
螺尾：向光滑表面过渡的牙底不完整的螺纹。
有效螺纹：由完整螺纹和不完整螺纹组成的螺纹，不包括螺尾。
公称直径：代表螺纹尺寸的直径。
大径：外螺纹的顶径、内螺纹的底径。
小径：外螺纹的底径、内螺纹的顶径。
中径：一个假想圆柱或圆锥的直径，该圆柱或圆锥的母线通过牙型上沟槽和凸起宽度相等的地方。
单一中径：牙型上沟槽宽度等于1/2基本螺距的地方。
作用中径：在规定的旋合长度内，恰好包容实际螺纹的一个假想螺纹的中径，这个假想螺纹具有理想的螺距、螺纹半角、及牙型高度，并在牙顶和牙底留有间隙，不与实际螺纹大、小径发生干涉。
牙型角：在螺纹牙型上，两相邻牙侧间的夹角。
螺距：相邻两牙在中径线上对应两点间的轴向距离。
螺纹精度：由螺纹公差带和旋合长度共同组成的衡量螺纹质量的综合指标。
二、.螺纹概述一般将螺纹分为圆柱螺纹和圆锥螺纹。
（一）圆柱螺纹1. 普通螺纹（又称米制或公制螺纹）螺纹代号M，牙形角60°，基本牙形为平顶。
精度等级：内螺纹4~8级，外螺纹3~9级。
2. 美标统一螺纹（又称60°英制螺纹）螺纹代号UNC、UNF、UNEF、UN、UNS，牙形角60°，基本牙形为平顶。
精度等级：内螺纹1B~3B，外螺纹1A~3A。
3. 非螺纹密封的管螺纹（又称圆柱管螺纹）螺纹代号G，牙形角55°，基本牙形为圆顶圆底。
精度等级：内螺纹标准级和D级，外螺纹A、B级。
4. 梯形螺纹螺纹代号Tr，牙形角30°（美标为29°），基本牙形为平顶平底。
精度等级：7~9级，（美标为2G~6G）。
各国标准螺纹基本尺寸对照表
英制管螺纹基本尺寸及公差（牙形角55º）BSPP英制锥管螺纹基本尺寸及公差（牙形角55º）BSPT美制管螺纹基本尺寸及公差（牙形角60º）UN(F)公制螺纹基本尺寸及公差(牙形角60º) M55°圆锥管螺纹基本尺寸对照表最新下载-汇兴达55°圆锥管螺纹基本尺寸对照表最新下载-汇兴达55°圆锥管螺纹(BSPT)2 R5 5"138.432.30911136.951135.4721.479R66"163.832.30911162.351160.8721.479聊城市鑫茂祥管业有限公司专业经营钢管规格：5mm*1mm—1020mm*200mm合金钢管、外径22mm-127mm冷轧无缝钢管、外径127mm-600mm.壁厚16mm-100mm.外径精度±0.5%,壁厚精度±5%热轧中厚壁无缝钢管、16Mn外径400—1600mm、壁厚20—60mm 的大口径厚壁卷管.可定尺到16米及各种规格的无缝方管、异型无缝钢管等.常备钢管种类有:构造用无缝钢管、流体用无缝钢管、液压无缝钢管、电力用无缝钢管、石油输送用无缝钢管、化肥设备用无缝钢管、煤矿用无缝钢管、不锈钢无缝钢管、化工用无缝钢管、纺织机械用无缝钢管、汽车；水利用无缝钢管.精密无缝钢管、光亮无缝钢管、军工医疗用无缝钢管、管道用无缝钢管、支柱用无缝钢管、合金无缝管、高压无缝管、大口径直缝焊管等。
适用于工程、煤矿、纺织、电力、锅炉、机械、军工等各个领域。
公司以良好的信用、优质的产品、雄厚的实力、低廉的价钱享誉全国30多个省、市、自治区、直辖市及国外.产品深得用户依赖。
管螺纹的基本尺寸表(2010-10-25 15:57:35)转载▼标签：杂谈表（1）螺纹基本尺寸G1/2 、ZG1/2 (单位:mm)尺寸代号每25.4mm类的牙数n螺距p 牙型高度h圆弧半径r≈基面上的基本直径基准距离有效螺纹长度大径（基准直径）d=D中径d2=D2小径d1=D11/16 28 0.907 0.581 0.125 7.723 7.142 6.561 4.0 6.5 1/8 28 0.907 0.581 0.125 9.728 9.147 8.566 4.0 6.5 1/4 19 1.337 0.586 0.184 13.157 12.301 11.445 6.0 9.7 3/8 19 1.337 0.586 0.184 16.662 15.806 14.950 6.4 10.1 1/2 14 1.814 1.162 0.249 20.955 19.793 18.631 8.2 13.2锥管螺纹的基本尺寸表（3-28）1/2PT 、1/2NPT表（2）螺纹基本尺寸 (单位:mm)螺纹标准的一种.按外形分圆柱、圆锥两种；按牙型角分55°、60°两种。