塑料制品企业常用的英语词汇
塑胶类英语词汇大全
废料粉碎机---scrap grinder顶出板,脱模板---stripper plate应力龟裂---stress cracking环境应力龟裂试验---environmental stress cracking test行程,衝程---stroke注道,注道料---sprue注道衬套,浇口衬套---sprue bush成形压力,模製压力---molding pressure成形温度,模製温度---molding temperature成形循环,成形週期---molding cycle成形时间,模製时间---molding time成形收缩,模压收缩---mold shrinkage, molding shrinkage窄浇口,限制形浇口---restricted gate剪切强度,抗剪强度---shear strength增亮剂---brightening agent,optical brightener,optical whitening agent 加速试验---accelerated test加速老化---accelerated ageing塑性变形---plastic deformation塑性流动---plastic fiow翘曲---warp(ing),warpage抗臭氧性---ozone resistance抗臭氧试验---ozone resistance test耐天侯性---weatherability,weather resistance耐光性---light resistance,light fastness天侯老化试验---weathering test耐酸性---acid resistance耐衝击性---impact resistance褪色---fading,discoloration耐蚀性---corrosion resistance拉桿,导柱---tie-bar拉桿间距---tie-bar distance多模穴模具---multi-cavity mold双色射出成形---double-shot molding超音(声)波镶嵌---ultrasonic inserting超音(声)波焊接---ultrasonic welding顶出,脱模---ejection顶出组合---ejector顶出板---ejector plate,knock-out plate顶出桿,脱模桿---knock-out bar,ejector rod无光面---dull surface低压射出成形法---low pressure injection molding硬度计---durometer电镀---electroplating,electrodeposition电铸模具---electroformed mold公差,容差---tolerance冷料---cold slug冷料井,冷料窝---cold slug well回程销,覆归销---surface pin冷热骤变试验---thermal shock test热应力龟裂---thermal stress cracking,TSC 侧向浇口---side gate侧向模蕊(心型)销---side draw pin砂磨---sanding喷砂,打砂---sand blast修饰,涂饰,打光---finishing自断浇口,剪切浇口---shear gate紫外线---ultraviolet, UV紫外线稳定剂---UV stabilizer紫外线吸收剂---UV absorber压花---embossing压花机---embossing machine喷霜,起霜---blooming exudation鯊皮斑---shark skin射出压力---injection pressure射出成形---injection molding射出成形机---injection molding machine 射出成形模具---injection mold射出装置---injection unit射出速度---injection speed射出喷嘴,注料嘴---injection nozzle射出容量---machine shot capacity射出率(量)---injection rate煮沸试验---boiling test充填不足,缺料---short shot手动模具---hand mold,loose mold手动油压机---hand press缩窝,凹孔---shrinkage pool衝击试验---inpact test衝击强度---impact strength烧结法,粉铸法---sintering烧结成形法---sinter molding模板---mold plate注射,射料---shot硅橡胶---silicone rubber真空成形---vacuum forming珠光顏料---pearlescent pigment浸渍涂装---dip coating人造皮革---artificial leather嵌件---insert嵌件销---insert pin气胀真空成形---air assist forming空气隙---air gap空气顶出---air ejection永久伸长---permanent elongation,tension set永久变形---permanent set,permanent deformation蚀刻,侵蚀---etching应力---stress应力鬆弛---stress relaxation应力龟裂---stress cracking应力集中---stress concentration应力断裂,应力破坏---stress rupture应力.应变曲线---stress-strain curve应力.应变图---stress-strain diagram托板,模板---retainer plate硬度---hardness合模机构---mold clamping mechanism合模力,闭模力---locking force,clamping force开模力---mold opening force悬臂梁---cantilever beam润滑剂---lubricant模具---mold,Tools,T ooling模温度控制器---mold temperature controller模具尺寸---mold size加热管套(料筒)---heating cylinder加热板---heating plate凸轮---cam玻璃纤维---glass fiber,fibrous glass玻璃纤维强化热塑塑胶---fiber glass reinforced thermoplastics,FRTP,glass fiber reinforced thermoplasitcs,GRTP玻璃纤维强化塑胶---glass fiber reinforced plastics,GRP,fiber galss reinforced plastics,FRP.感光聚合物---photopolymer,photo-sensitive polymer镜面抛光---mirror polishing龟裂---cracking龟裂---crack颗粒料---granule石墨---graphite石墨纤维---graphite fiber间隙, 隙距---clearance模蕊,蕊片,蕊线,蕊孔---core成孔销,模蕊销---core pin成孔销托板---core pin platephenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PA polybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POMpolyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO polypropylene 聚丙烯PPpolystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PEpolyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVApolyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 矽树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树脂入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrodecompre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具encapsulation molding低压封装成型、射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口diaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Runner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣。
塑料制品企业常用英语词汇
塑料制品企业常用英语词汇一、组织机构及职位XX电子有限公司XX Electronics CO., Ltd总经理办公室General manager’s office企管部Enterprise management department (EM)行政部Administration department (AD)销售部Sales department (SD)财务部Financial department (FD)技术部Technology department (TD)物控部Production material control department (PMC)生产部Production department(PD)模具部Mold manufacturing department, Tooling manufacturing department (TM) 品管部Quality Assurance department (QA)冲压车间Stamp workshop, press workshop注塑车间injection workshop装配车间Assembly workshop模具装配车间Mold and die Assembly workshop金属加工车间meta l machine workshop电脉冲车间Electric discharge process workshop线切割车间wire cutting process workshop工磨车间Grinding workshop总经理General manager (GM)副总经理Vice-general manager经理manager董事长president副董事长Vice-presidentXX部门经理Manager of XX department主任、主管supervisor拉长Line leader组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant二、产品连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压rated voltage额定电流rated current接触电阻contact resistance超声波焊接ultrasonic welding耐压withstand voltage针pin物料编号part number导线wire基体金属Base meta l电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity接触长度contact length接触件电镀层contact plating接触压力contact pressure接触件中心距contact space接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring多层印制电路Multilayer printed circuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board表面安装surface Mounting翘曲warp，bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plate Top plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush 直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould 脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining 数控加工中心CNC machine center卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine 四、品管SPC statistic process control品管保证Quality Assurance品管控制Quality control来料检验IQC Incoming quality control巡检IPQC In-process quality control校对calibration动态试验dynamic test环境试验Environmental test非破坏性试验non-destructive test光泽gloss击穿电压(dielectric) breakdown voltage拉伸强度tensile strength冷热骤变试验thermal shock test环境试验炉Environmental chamber盐雾实验salt spray test绝缘电阻测试验仪Insulating resistance meter 内应力internal stress疲劳fatigue蠕变creep试样specimen撕裂强度tear strength缩痕shrink mark, sink mark耐久性durability抽样sampling样品数量sample sizeAQL Acceptable Quality level批量lot size抽样计划sampling planOC曲线operation curve试验顺序sequence of tests环境温度ambient temperature可焊性solderability阻燃性flame resistance五、生产注塑机injection machine冲床Punch machine混料机blender mixer尼龙nylon黄铜brass紫(纯)铜copper料斗hopper麻点pit配料compounding涂层coating飞边flash预热preheating再生料reworked material再生塑料reworked plastics工艺设计process design紧急停止emergency stop延时time delay六、物控保质期shelf lifeABC分类法ABC Classification反常需求Abnormal Demand措施信息Action Message活动报告标志Action-report-flag基于活动的成本核算Activity-based Costing (ABC) 实际能力Actual Capacity实际成本Actual Costs调整现有库存量Adjust-on-hand已分配量Allocation替代工序Alternative Routine装配订单Assembly Order装配零件表Assembly Parts List装配Assembly计划自动重排Automatic Rescheduling可达到库存Available Inventory可用材料Available Material达到库存Available Stock可利用工时Available Work可签约量Available-to-promise平均库存Average Inventory欠交订单Back Order倒序计划Back Scheduling倒冲法Back flush未完成订单Backlog现有库存余额Balance-on-hand Inventory批号Batch Number批量生产Batch Production标杆瞄准Benchmarking工时清单Bill of Labor提货单Bill of Lading物料清单Bill of Material分库Branch Warehouse经营规划Business Plan能力管理Capacity Management能力需求计划Capacity Requirements Planning (CRP)保管费率Carrying Cost Rate保管费Carrying Cost单元式制造Cellular Manufacturing修改批量日期Change Lot Date修改工序Change Route修改产品结构Change Structure检查点Check Point闭环物料需求计划Closed Loop MRP通用工序标识Common Route ID计算机集成制造Computer-integrated Manufacturing (CIM)配置代码Configuration Code约束管理/约束理论Constraints Management/Theory of Constraints (TOC) 依成本的材料清单Costed Bill of Material急需零件Critical Part累计提前期Cumulative Lead Time现有运转时间Current Run Hour现有运转数量Current Run Quantity周期盘点Cycle Counting调整日期Date Adjust有效日期Date Available修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required发货日期Date to Pull空负荷Dead Load需求管理Demand Management需求Demand实际能力Demonstrated Capacity非独立需求Dependent Demand直接增减库存处理法Direct-deduct Inventory Transaction Processing发料单Disbursement List派工单Dispatch List分销资源计划Distribution Resource Planning (DRP)鼓－缓冲－绳子Drum-buffer-rope经济订货批量Economic Order Quantity (EOQ)工程变更生效日期Engineering Change Effect Date工程变更生效单Engineering Change Effect Work Order工程停止日期Engineering Stop Date例外控制Exception Control急送代码Expedite Code加工订单Fabrication Order补足欠交Fill Backorder总装提前期Final Assembly Lead Time确认的计划订单Firm Planned Order固定订货批量F ixed Order Quantity集中预测Focus Forecasting完全跟踪Full Pegging通用生产管理原则Generally Accepted Manufacturing Practices 毛需求Gross Requirements在制品库存In Process Inventory独立需求Independent Demand投入/产出控制Input/ Output Control检验标识Inspection ID厂际需求Interplant Demand库存周转率Inventory Carry Rate仓库库位类型Inventory Location Type库存周转次数Inventory Turnover发送订单Issue Order项目记录Item Record物料项目Item加工车间Job Shop准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time层Level负荷量Load Leveling负荷报告Load Report负荷Load仓位代码Location Code仓位备注Location Remarks仓位状况Location Status按需订货Lot for Lot批量标识Lot ID批量编号Lot Number批量Lot Size低位码Low Level Code机器能力Machine Capacity机器加载Machine Loading外购或自制决策Make or Buy Decision面向订单生产的产品Make-to-order Product面向库存生产的产品Make-to-stock Product制造周期时间Manufacturing Cycle Time制造资源计划Manufacturing Resource Planning (MRP II)主生产计划Master Production Schedule (MPS)物料发送和接收Material Issues and Receipts物料需求计划Material Requirements Planning (MRP)登陆标志MPS Book Flag MPS多重仓位Multiple Location净改变式MRP N et Change MRP净需求Net Requirements新仓位New Location新组件New Parent新仓库New Warehouse不活动报告No Action Report现有库存量On-hand Balance未结订单Open Order订单输入Order Entry订货点Order Point订货方针Order Policy订货承诺Order Promising订货备注Order Remarks双亲Parent零件清单Part Bills零件批次Part Lot零件编号Part Number零件Part反查Pegging领料单Picking List领料/提货Picking计划订单Planned Order后减库存处理法Post-deduct Inventory Transaction Processing 前减库存处理法Pre-deduct Inventory Transaction Processing 发票价格Price Invoice采购订单价格Price Purchase Order优先计划Priority Planning产品控制Product Control产品线Production Line生产规划编制Production Planning产品率Production Rate产品结构树Production Tree预计可用库存Projected Available Balance采购订单跟踪Purchase Order Tracking已分配量Quantity Allocation仓位数量Quantity At Location欠交数量Quantity Backorder完成数量Quantity Completion需求量Quantity Demand毛需求量Quantity Gross进货数量Quantity In排队时间Queue Time队列Queue重排假设Rescheduling Assumption资源需求计划Resource Requirements Planning粗能力计划Rough-cut Capacity Planning工艺路线Routing安全库存量Safety Stock保险期Safety Time预计入库量Scheduled Receipt残料率Scrap Factor发送零件Send Part维修件Service Parts发货地址Ship Address发货单联系人Ship Contact发货零件Ship Date发货单Ship Order工厂日历Shop Calendar车间作业管理Shop Floor Control损耗系数Shrinkage Factor标准产品成本Standard Product Cost标准机器设置工时Standard Set Up Hour标准单位运转工时Standard Unit Run Hour标准工资率Standard Wage Rate状况代码Status Code库存控制Stores Control建议工作单Suggested Work Order约束理论Theory of Constraints (TOC)时间段Time Bucket时界Time Fence单位成本Unit Cost采购计划员Vendor Scheduler采购计划法Vendor Scheduling工作中心能力Work Center Capacity工作中心Work Center在制品Work in Process工作令跟踪Work Order Tracking工作令Work Order工作进度安排Work Scheduling零库存Zero Inventories经济订货批量＝Squat(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本) 美国生产和库存控制协会APICS，American Production & Inventory Control Society 七、QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan，产品质量先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析MSA Measure System Analysis,测量系统分析SPC Statistical Process Control,统计过程控制审核Audit能力Capability控制计划Control Plans纠正措施Corrective Action文件Documentation作业指导书Job Instruction, work instruction不合格品Nonconformance不合格Nonconformity每百万零件不合格数Defective Parts Per Million, DPPM 预防措施Preventive Action程序Procedures过程流程图Process Flow Diagram, Process Flow Chart 质量手册Quality Manual质量计划Quality Plan质量策划Quality Planning质量记录Quality Records原始数据Raw Data反应计划Reaction Plan返修Repair。
塑胶行业英文专业用语
塑胶行业英语Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡Void 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2Poor dispersion 分散不好FR/PTFE…agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密、蜜蜂窝Low impact/tensile ect 物理性能低High flow/filler content etc流动性、填充…过高Longs/fines/doubles 长粒、碎屑、连粒Poor cut 粒形不好Bristle/voids 表面有小气泡、孔Glass bundles 玻纤结团Product was rejected due to产品不能接受因为…High moisture level 高水分Warpage/warped翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱、长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra…添加多一点…Reduced … content 减少…含量Dropped/reduced … by X%减少…含量…x%Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个订单Expected to finish by…预计在…完成Expected order is xMT 预计订量…吨Estimated annual/monthly consumption 预计年、月用量。
常用塑胶英语词汇以及与客户沟通邮件语句
DFM English and design Principles一．产品信息： Product information1. 外观： Surface Appearance2. 光洁度： Glossiness/gloss finish3. 毛面： Matt finish/matt surface4. 皮纹粒度： Grain5. 特殊皮纹区域： Special area texture6. 塑料色母 : M aster batch7. 烫金 / 涂层 / 印刷 / 雾晕 H ot stamping/ coating/ print/ haze8. 仿皮革 : leather cloak9. 电火花纹： EDM10. 光化学腐蚀法： Photochemical etching11. 刷涂纹，拉丝纹 Brushing12. 激光雕刻： Laser engraving13. 喷砂： Sand blasting1. 设计版本 : D esign revision2. 产品重量： part weight3. 注射重量： Shot weight4. 流道重量： R unner weight5. 驻留时间： Resident time6. 缩水率： Shrinkage7. 最终外观： Cosmetic finishing:8. 塑胶材料： Resin material9. 塑胶等级： Resin Grade10. 产品体积： part volume二．浇口类型： G ate type自动脱模浇口 Automatic gate1. 潜伏式浇口： Submarine gate2. 香蕉形浇口： Cashew gate ， banana gate3. 针点式浇口： Pin gate4. 热浇道口： Hot drop5 针阀浇口： Valve gate手动整理浇口 Manual gate1. 边缘浇口： Edge gate2. 凸耳浇口： Tab gate overlap gate3. 直接浇口： Sprue gate4. 隔膜浇口： Diaphragm gate5. 环形浇口： Ring gate6. 扇形浇口： Fan gate7. 薄膜浇口： Flash gate8. 过滤器瞟浇口： Filter Rowl gate说明： illustrate●浇口进入位： G ate location●浇口大小： Gate size●转水口： Switching runner / gate ●唧嘴口径： Sprue diameter●水口殘留最大 0.1m m. T he maximal residual gate is 0.1mm . Gates Vestige will be 0.1mm●此水口会用 CNC 铣平 : T he gate will be milled to flat by CNC.●此位会作凹陷 Here will be recess.●浇口需要冲床机器二次加工来去除： Gates n eed 2nd p rocess r emove by stamping machining●透明件不宜用香蕉浇口，易见流痕： The banana gate does not suite the transparent part. F low mark is visible.●最终的进胶位置根据模流分析： Finally gate position according the mold flow analysis.●顶出后额外的墙被切掉 : Extra wall t o be cut away after ejection●是否可以添加一个小肋骨用来放潜水口 , 成型后再删除它如果必要的话：Is it possible to add one small rib to place sub gate, after molding remove it by operator if necessary三．流道 : runner●冷流道： C old runner1. 唧嘴直流 : Direct sprue gate2. 圆形流道： R ound(full/half ) runner3. 正圆形： Full Round （最有效） Most Efficient4. 梯形： Trapezoidal ( 有效） Good5. 半圆形： Half Round （非有效） N ot Good●热流道： Hot runner1. 热流道板： H ot manifold2. 热嘴转冷流道 : hot sprue turn to cold runner3. 热流道转冷流道 : hot tips turn to cold runner●冷料井— cold slug well说明： illustrate●单嘴阀针式热流道转冷流道 : 1 drops valve nozzle to cold runner●单嘴尖点式热流道转冷流道 : 1 drops tip nozzle to cold runner●单嘴开放式热流道转冷流道 : 1 drops open nozzle to cold runner● 2 点针阀式直接进胶 : Hot runner 2 drops valve nozzle direct to part●喷嘴 Nozzle设计原则： Design principles●根据模流分析结果最后确定浇口位置： Finally gate position according the mold flow analysis●检查流动长度在薄壁产品： check f low length in thin walled part●竖浇道太长了约有 200mm 長 . 冷流道系统流动不均 , 推荐使用热流道以使流动较佳 . The sprue will be too long if we use cold runner design. Its length is around 200 millimeters ， Flow imbalance by cold runner ， We recommend a hot runner system for better flow.●浇道系统应该有一个均衡的布局： R unner system should have a balanced layout●省料： Savings in material●周期短： Shorter cycles●浇口在最佳位置： Gates at the best position●压力降最小： Pressure losses minimized●人工系统流道平衡： Artificial balancing of the gate system●避免焊缝线 : Avoidance of weld line●纤维取向 : Fiber orientation●避免迟滯效应： Avoid the hysteresis effect●避免潜流： avoid underflow●所有的流道都要有冷料井： All runners are to have cold slug wells ●多型腔模具浇口尺寸必须相同，平衡必须经过调整流道而不是调整浇口。
塑料机械类常用英语（一.组装、冲压、喷漆等专业词汇）
塑料机械类常用英语（一.组装、冲压、喷漆等专业词汇）Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床|刨床 planer |'pleinmiller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良n|氧化 oxidation |' ksi'deiscratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect 外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption 消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑。
塑料英语 塑料件用语英文对照(参照分析)
塑料件用语英文对照注塑机injection machine 冲床Punch machine 混料机blender mixer 尼龙nylon 黄铜brass 青铜bronze 紫(纯)铜copper 料斗hopper 麻点pit 配料compounding 涂层coating 飞边flash 预热preheating 再生料reworked material 再生塑料reworked plastics 工艺设计process design 紧急停止emergency stop 延时time delay质量SPC statistic process control 品管保证Quality Assurance 品管控制Quality control 来料检验IQC Incoming quality control 巡检IPQC In-process quality control 校对calibration 动态试验dynamic test 环境试验Environmental test 非破坏性试验non-destructive test 光泽gloss 击穿电压(dielectric) breakdown voltage 拉伸强度tensile strength 冷热骤变试验thermal shock test 环境试验炉Environmental chamber 盐雾实验salt spray test 绝缘电阻测试验仪Insulating resistance meter 内应力internal stress 疲劳fatigue 蠕变creep 试样specimen 撕裂强度tear strength 缩痕shrink mark, sink mark 耐久性durability 抽样sampling 样品数量sample size AQL Acceptable Quality level 批量lot size 抽样计划sampling plan OC曲线operation curve 试验顺序sequence of tests 环境温度ambient temperature 可焊性solderability 阻燃性flame resistance模具塑料模具mould of plastics 注塑模具injection mould 模架mould base set方铁spacer plate 底针板ejector plate 面针板ejector retainer plate 回针Return pin 导柱Guide pin 托导套Shoulder Guide bush 直导套Straight Guide bush 动模座板Bottom clamp plate Moving clamp plate 基准线datum line 基准面datum plan 型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin 单腔模具single cavity mould 多腔模具multi-cavity mould 多浇口multi-gating 浇口sprue/gate缺料starving 排气breathing 光泽gloss 合模力mould clamping force 锁模力mould locking force 挤出extrusion 开裂crack 循环时间cycle time 老化aging 螺杆screw 麻点pit 嵌件insert 活动镶件movable insert 起垩chalking 浇注系统feed system主流道sprue 分流道runner 浇口gate 直浇口direct gate , sprue gate 轮辐浇口spoke gate , spider gate 点浇口pin-point gate 测浇口edge gate 潜伏浇口submarine gate , tunnel gate 料穴cold-slug well 浇口套sprue bush 流道板runner plate 排飞槽vent 分型线（面）parting line 定模stationary mould，Fixed mould 动模movable mould, movable half 上模upper mould upper half 下模lower mould，lower half 型腔cavity 拼块split 定位销dowel 定位销孔dowel hole 型芯core 斜销angle pin, finger cam 滑块slide 滑块导板slide guide strip 楔紧块heel block, wedge lock 拉料杆sprue puller 定位环locating ring 冷却通cooling channel 脱模斜度draft 滑动型芯slide core 螺纹型芯threaded core 热流道模具hot-runner mould 绝热流道模insulated runner mould 熔合纹weld line （flow line）三板式模具three plate mould 脱模ejection 换模腔模具interchangeable cavity mould 脱模剂release agent 注射能力shot capacity 注射速率injection rate 注射压力injection pressure 差色剂colorant 保压时间holdup time 闭模时间closing time 定型装置sizing system 阴模female mould，cavity block 阳模male mould 电加工设备Electron Discharge Machining 数控加工中心CNC machine center 万能铁床Universal milling machine 卧式刨床Horizontal planer 车床Engine lathe 平面磨床Surface grinding machine 去磁机Demagnetization machine 万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller 超声波清洗机Ultrasonic clearing machine产品连接器connector 端子terminal 条型连接器bar connector 阴连接器Housing 阳连接器wafer 线束wire harness 间距space 额定电压rated voltage 额定电流rated current 接触电阻contact r䁥sistance 绝缘电阻insulation resistance 超声波焊接ultraųonic welding 耐压wi聴hstand voltage 针pin导线wire 基体金属Base metal 电缆夹cable clamp 倒角chamfer 接触面积contact area 接触件安装孔contact cavity 接触长度contact length 接触件电镀层contact plating 接触压力contact pressure 接触件中心距contact space 接触簧片contact spring 插孔socket contact 法兰、凸缘Flange 界面间隙interfacial gap 键Key 键槽keyway 过渡段ramp 屏蔽套shielding 定位基准Datum reference 扁平电缆flat cable ，Ribbon cable 柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printed circuit 焊盘pad 图形pattern 间距pitch 负极Negative pole 正极positive pole 回流Reflow 原理图Schematic diagram 单面板single sided board 双面板Two-sided board，Double-sided board 表面安装surface Mounting 翘曲warp，bow 波峰焊wave soldering 编织层braid 同轴电缆coaxial cable 电介质dielectric 电缆中导线的头数ends 外部干扰external interference 填充物filler 护套jacket 比重specific gravity 电阻的温度系数Temperature coefficient of resistancePlastic 塑胶塑料composite material 符合材料engineering plastics 工程塑胶expanded 发泡的fiber reinforcement 纤维强化复合材料high density 高密度~low density 低密度high impact 高冲击性~prepolymer 预聚物thermoplastic 热塑性thermosetting 热固性unsaturated polyester 不饱和的聚酯纤维/树脂activator 活化剂bag moulding 带模施压成型bonding strength 粘结强度breathing 排气caulking compound 填缝/捻缝料cell 气孔blister 气泡涨破color masterbatch 色母料color matching 调色/配色colorant 着色剂compund 混合料copolymer 共聚物cull 剔除，挑出ductility 展延性/柔软性elastomer 人造橡胶弹性体extrude 挤出filler 填充剂feed 供料film blowing 薄膜吹制floating 浮动/活动的foaming agent 发泡剂foaming part 发泡件gunk 料斗hot mark 热斑热痕打标记hot stamping 烫印injection nozzle 射出喷嘴injedtion plunger 注射柱塞plunger 压料柱塞kneader 混合机lubricant 润滑剂leveling agent 匀涂剂mould clamping force 锁模力mould release agent 脱模剂oriented film 取向薄膜parison 吹塑块料pellet 粒丸粒料plasticizer 可塑剂porosity 孔隙率多孔性internal porosity 内部气孔void content 孔隙量空洞率post cure 后固化premix 预混料resilience 还原能力，回弹性resin injection 树脂射出法shot 注射shot cycle 注射圈数take out device 取料装置transparency 透明性atomization 雾化aberration 色差偏差异常现象bite 咬入blacking hole 涂料气孔针孔blacking scab 涂料疤blooming 起霜blushing 泛白breaking-in 磨合试车敲陷burn mark 糊斑burr 毛刺-金属flash 毛刺-塑料camber 翘曲collapse 塌陷clamp-off 铸件凹痕color mottle 色斑mottle 斑点corrosion 腐蚀crack 裂纹crazing 龟裂edge crack 裂边fading 褪色fissure 裂开flange wrinkle 法兰起皱flaw 缺陷瑕疵galling 毛边擦伤gloss 光泽grinding defect 磨痕haze 雾incrustation 水锈沉淀物indentation 凹口缺口mismatch 偏模不吻合necking 缩颈nick 缺口割伤orange peel 橘皮状表面surface roughening 表面粗糙overflow 溢流pit 坑麻点peeling 剥离pitting corresion 点状腐蚀plate mark 模板印痕resin streak 树脂流纹resin wear 树脂脱落sagging 下垂松垂saponification 皂化scrap jam 废料阻塞short shot 填充不足欠注。
塑料加工专业英语
塑料加工专业英语
Plastic Processing专业英语是指与塑料制品的加工工艺、产品设计、设备和工艺参数等相关的英语词汇和表达方式。
下面是一些相关的塑料加工专业英语词汇和表达方式：
1. Injection molding 注塑成型
2. Extrusion 挤出
3. Blow molding 吹塑
4. Rotational molding 旋转成型
5. Thermoforming 热成型
6. Compression molding 压缩成型
7. Calendering 挤压
8. Plasticizing 熔化
9. Melt temperature 熔融温度
10. Injection pressure 注塑压力
11. Cooling time 冷却时间
12. Mold cavity 模腔
13. Ejector pin 弹簧顶杆
14. Gate sprue 浇口
15. Runner system 平衡道
16. Mold release agent 脱模剂
17. Plasticizer 增塑剂
18. Reinforcement 增强剂
19. Melt flow index 熔体流动指数
20. Mold shrinkage 模具收缩率
这些词汇和表达方式可以帮助从事塑料加工专业的人更好地理解和沟通相关的技术和工艺要求。
塑胶专业词汇
blister 起泡pock mark 痘斑resin streak 树脂流纹blooming 起霜resin wear 树脂脱落riding 凹陷blow hole 破孔sagging 松垂saponification 皂化blushing 泛白scar 疤痕scrap 废料body wrinkle 侧壁皱纹scrap jam 废料阻塞scratch 刮伤/划痕breaking-in 冒口带肉burn mark 糊斑bubble 膜泡burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷straightening 矫直streak 条状痕clamp-off 铸件凹痕surface check 表面裂痕surface roughening 橘皮状表皮皱折collapse 塌陷surging 波动Streak条纹color mottle 色斑Sink Mark凹陷(Weld Line) 熔接线corrosion 腐蚀(Flow Line)流痕scratch划伤crack 裂痕mixed color杂色shrinking/shrinkage缩水crazing 碎裂crazing 龟裂painting peel off脏污inclusion杂质deformation 变形grease/oil stains油污flash(塑件)毛边edge 切边碎片poor staking铆合不良excesssive gap间隙过大burr(金属) edge crack 裂边deformation变形rust生锈speckle斑点fading 退色mildewed=moldy=mouldy发霉torsion 扭曲filler speak 填充料斑slipped screwhead/shippery screw thread滑手warpage 翘曲fissure 裂纹slipped screwhead/slippery screw head螺丝滑头waviness 波痕flange wrinkle 凸缘起皱cosmetic defect外观不良not up to standard不合规格flaw 刮伤dimension/size is a little bigger尺寸偏大(小) webbing 熔塌flow mark 流痕minor defect次要缺陷major defect主要缺陷galling 毛边critical defect极严重缺陷excessive defects过多的缺陷glazing 光滑wrong part错件wrinkle 皱纹missing part漏件gloss 光泽whitening 白化weld mark 焊痕grease pits 污斑sweat out 冒汗pock 麻点grinding defect 磨痕plate mark 模板印痕pitting corrosion 点状腐蚀haircrack 发裂pit 坑peeling 剥离haze 雾度overflow 溢流orange peel 橘皮状表面缺陷incrustation 水锈nick 割痕necking 缩颈indentation 压痕mottle 斑点mismatch 偏模internal porosity 内部气孔There are material 内有物Tin line within 内有锡线electric fan 电风扇air conditioner 空调Absorber Circuit 吸收电路Control Circuit 控制电路electrical isolation 电气隔离frequency converter 变频器general purpose diode 普通二极管high voltage IC 高压集成电路hard switching 硬开关no-load 空载full load 满载de machine 直流电机light emitting diode 发光二极管regulator 调节器reactive power 无功功率potential transformer 电压互感器stabilizing transformer 稳定变压器circuit components 电路元件electrical device 电气设备direct-current 直流circuit diagram 电路图internal resistance 内阻self-inductor 自感leakage current 漏电流polarity 极性mutual-inductor 互感phase reversal 反相transformer 变压器induction machine 感应电机power amplifier 功率放大器rheostat 变阻器corridor 通路leakage 泄漏tuner 调谐器Amplitude Modulation(AM 调幅frequency 频率overhauling 检修direct-current 直流negative ions 负离子Discharge 放电partial discharge 局部放电grounding 接地Power factor 功率因数gaseous insulation 气体绝缘Deenergize 断电Induction 感应withst and voltage 耐受电压Malfunction 失灵Nameplate 铭牌Creep distance 爬电距离IC (integrated circuit) 集成电路terminal 接线端子fuse 保险丝，熔丝amplitude modulation (AM) 调幅frequency modulation (FM) 调频humidity湿度calibrate 校准moisture 潮湿，湿气rated 额定的Recovery voltage 恢复电压Bushing 套管resonance 谐振，共振Inductive (Capacitive) 电感的(电容的) relay继电器Warpage翘曲转自:<a href='/'>育路国际商务师考试网</a>。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
七．QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan，产品质量先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析MSA Measure System Analysis,测量系统分析SPC Statistical Process Control,统计过程控制审核Audit能力Capability能力指数Capability Indices控制计划Control Plans纠正措施Corrective Action文件Documentation作业指导书Job Instruction, work instruction 不合格品Nonconformance不合格Nonconformity每百万零件不合格数Defective Parts Per Million, DPPM预防措施Preventive Action程序Procedures过程流程图Process Flow Diagram, Process Flow Chart质量手册Quality Manual质量计划Quality Plan质量策划Quality Planning质量记录Quality Records原始数据Raw Data反应计划Reaction Plan返修Repair。
返工Rework现场Site分承包方Subcontractors产品product质量quality质量要求quality requirement顾客满意customer satisfaction质量管理体系quality management system质量方针quality policy质量目标quality objective 质量管理quality management质量控制quality control质量保证quality assurance组织organization顾客customer供方supplier过程process服务service设计与开发design and development：特性characteristic可追溯性trace ability合格conformity缺陷defect纠正correction让步concession放行release报废scrap规范specification检验inspection试验test验证verification评审review测量measurement计数型数据Attributes Data普通原因Common Cause单值Individual均值Mean随机抽样Random Sampling极差Range特殊原因Special Cause稳定性Stability子组Subgroup计量型数据variables Data变差variation固有变差Inherent variation总变差Total variation偏倚Bias重复性Repeatability再现性Reproducibility稳定性Stability线性Linearity分辨率Resolution过程更改Process change质量功能展开QFD过程特殊特性Special Process Characteristic 产品特殊特性Special Product Characteristic 外观项目Appearance Item初始过程能力Preliminary Process Capability 材料清单Bill of Material设计确认Design Validation设计验证Design Verification顾客的呼声Voice of the Customer过程的呼声Voice of the Process八．常用缩略词语1、ES 工程规范Engineering Specification2、KCC 关键控制特性（GM）Key Control Characteristic3、KPC 关键产品特性（GM）Key Product Characteristic4、OEM 整车厂Original Equipment Manufacturer5、SC重要(特殊)特性Significant(Special) Characteristic6、ANOVA 方差分析法Analysis of variance7、CFT 多方论证小组Cross function Team8、DFMEA 设计失效模式及后果分析Design Failure Mode and Effects Analysis9、DOE 试验设计Design of Experiment10、DVP&R 设计验证计划和报告Design verification Plan and Report11、FTC 试生产能力First Time Capability12、GR&R 量具的重复性和再现性Gage Repeatability and Reproducibility13、PFMEA 过程失效模式及后果分析Process Failure Mode and Effect Analysis 14、SFMEA 系统失效模式及后是分析System Failure Mode and Effect Analysis 15、QSR 质量体系要求Quality System Requirement16、QFD 质量功能展开Quality function Deployment17、TGR 运行情况良好Things Gone Right18、TGW 运行情况不良Things Gone Wrong19、VE/VA 价值工程/价值分析Value Engineering/Value Analysis20、BOM 物料清单Bill of Material21、Cpk 稳定过程的能力指数Capability for stable process22、LCL 下控制限Lower Control Limit23、UCL 上控制限Upper Control Limit24、LSL 工程规范下限Lower Specification Limit25、USL 工程规范上限Upper Specification Limit26、Ppk 性能指数The performance index27、MRB 物料评审Material Review Board28、PSW 零件提交保证书Part Submission Warrant29、X(—)--R图均值一极差图Average-Range Chart30、SRPC 供方要求产品更改Supplier Request for Product Change31、SREA 供方工程批准的要求Supplier Request for Engineering Approval32、IAA 临时批准授权Interim Approval Authorization33、AAR 外观件批准报告Appearance Approval Report34、PTR 试生产(报告) Production Trial Run (Report)35、DCP尺寸控制计划(动态控制计划)Dimension Control Plan (Dynamic Control Plan)37、防错（POKA-YOKE）Mistake Proofing 加工订单Fabrication Order补足欠交Fill Backorder总装提前期Final Assembly Lead Time确认的计划订单Firm Planned Order固定订货批量F ixed Order Quantity集中预测Focus Forecasting完全跟踪Full Pegging通用生产管理原则Generally Accepted Manufacturing Practices毛需求Gross Requirements在制品库存In Process Inventory独立需求Independent Demand投入/产出控制Input/ Output Control检验标识Inspection ID厂际需求Interplant Demand库存周转率Inventory Carry Rate仓库库位类型Inventory Location Type库存周转次数Inventory Turnover发送订单Issue Order项目记录Item Record物料项目Item加工车间Job Shop准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time层Level负荷量Load Leveling负荷报告Load Report负荷Load仓位代码Location Code仓位备注Location Remarks仓位状况Location Status按需订货Lot for Lot批量标识Lot ID批量编号Lot Number批量Lot Size低位码Low Level Code机器能力Machine Capacity机器加载Machine Loading外购或自制决策Make or Buy Decision面向订单生产的产品Make-to-order Product 面向库存生产的产品Make-to-stock Product 制造周期时间Manufacturing Cycle Time制造资源计划Manufacturing Resource Planning (MRP II)主生产计划Master Production Schedule (MPS)物料成本Material Cost物料发送和接收Material Issues and Receipts 物料需求计划Material Requirements Planning (MRP)登陆标志MPS Book Flag MPS多重仓位Multiple Location净改变式MRP N et Change MRP净需求Net Requirements新仓位New Location新组件New Parent新仓库New Warehouse不活动报告No Action Report 现有库存量On-hand Balance未结订单Open Order订单输入Order Entry订货点Order Point订货方针Order Policy订货承诺Order Promising订货备注Order Remarks双亲Parent零件清单Part Bills零件批次Part Lot零件编号Part Number零件Part反查Pegging领料单Picking List领料/提货Picking计划订单Planned Order后减库存处理法Post-deduct Inventory Transaction Processing前减库存处理法Pre-deduct Inventory Transaction Processing发票价格Price Invoice采购订单价格Price Purchase Order优先计划Priority Planning产品控制Product Control产品线Production Line生产规划编制Production Planning产品率Production Rate产品结构树Production Tree预计可用库存Projected Available Balance采购订单跟踪Purchase Order Tracking已分配量Quantity Allocation仓位数量Quantity At Location欠交数量Quantity Backorder完成数量Quantity Completion需求量Quantity Demand毛需求量Quantity Gross进货数量Quantity In排队时间Queue Time队列Queue重生成式MRP Regenerated MRP重排假设Rescheduling Assumption资源需求计划Resource Requirements Planning粗能力计划Rough-cut Capacity Planning工艺路线Routing安全库存量Safety Stock保险期Safety Time预计入库量Scheduled Receipt残料率Scrap Factor发送零件Send Part维修件Service Parts发货地址Ship Address发货单联系人Ship Contact发货零件Ship Date发货单Ship Order工厂日历Shop Calendar车间作业管理Shop Floor Control损耗系数Shrinkage Factor标准产品成本Standard Product Cost标准机器设置工时Standard Set Up Hour标准单位运转工时Standard Unit Run Hour 标准工资率Standard Wage Rate状况代码Status Code库存控制Stores Control建议工作单Suggested Work Order约束理论Theory of Constraints (TOC)时间段Time Bucket时界Time Fence单位成本Unit Cost采购计划员Vendor Scheduler采购计划法Vendor Scheduling工作中心能力Work Center Capacity工作中心Work Center在制品Work in Process工作令跟踪Work Order Tracking工作令Work Order工作进度安排Work Scheduling零库存Zero Inventories经济订货批量＝Squat(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本)美国生产和库存控制协会APICS，American Production & Inventory Control Society五、生产注塑机injection machine冲床Punch machine混料机blender mixer尼龙nylon 黄铜brass青铜bronze紫(纯)铜copper料斗hopper麻点pit配料compounding涂层coating飞边flash预热preheating再生料reworked material再生塑料reworked plastics工艺设计process design紧急停止emergency stop延时time delay六．物控保质期shelf lifeABC分类法ABC Classification反常需求Abnormal Demand措施信息Action Message活动报告标志Action-report-flag基于活动的成本核算Activity-based Costing (ABC)实际能力Actual Capacity实际成本Actual Costs调整现有库存量Adjust-on-hand已分配量Allocation替代工序Alternative Routine装配订单Assembly Order装配零件表Assembly Parts List装配Assembly计划自动重排Automatic Rescheduling可达到库存Available Inventory可用材料Available Material达到库存Available Stock可利用工时Available Work可签约量Available-to-promise平均库存Average Inventory欠交订单Back Order倒序计划Back Scheduling倒冲法Back flush未完成订单Backlog现有库存余额Balance-on-hand Inventory批号Batch Number批量生产Batch Production标杆瞄准Benchmarking工时清单Bill of Labor提货单Bill of Lading物料清单Bill of Material分库Branch Warehouse经营规划Business Plan采购员Buyer能力管理Capacity Management能力需求计划Capacity Requirements Planning (CRP)保管费率Carrying Cost Rate保管费Carrying Cost单元式制造Cellular Manufacturing修改批量日期Change Lot Date修改工序Change Route修改产品结构Change Structure检查点Check Point闭环物料需求计划Closed Loop MRP通用工序标识Common Route ID计算机集成制造Computer-integrated Manufacturing (CIM)配置代码Configuration Code约束管理/约束理论Constraints Management/Theory of Constraints (TOC)依成本的材料清单Costed Bill of Material急需零件Critical Part累计提前期Cumulative Lead Time现有运转时间Current Run Hour现有运转数量Current Run Quantity周期盘点Cycle Counting调整日期Date Adjust有效日期Date Available修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required发货日期Date to Pull空负荷Dead Load需求管理Demand Management 需求Demand实际能力Demonstrated Capacity非独立需求Dependent Demand直接增减库存处理法Direct-deduct Inventory Transaction Processing发料单Disbursement List派工单Dispatch List分销资源计划Distribution Resource Planning (DRP)鼓－缓冲－绳子Drum-buffer-rope经济订货批量Economic Order Quantity (EOQ)工程变更生效日期Engineering Change Effect Date工程变更生效单Engineering Change Effect Work Order工程停止日期Engineering Stop Date例外控制Exception Control呆滞材料分析Excess Material Analysis急送代码Expedite Code三、模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core 斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine 四、品管SPC statistic process control品管保证Quality Assurance品管控制Quality control来料检验IQC Incoming quality control巡检IPQC In-process quality control校对calibration动态试验dynamic test环境试验Environmental test非破坏性试验non-destructive test光泽gloss击穿电压(dielectric) breakdown voltage拉伸强度tensile strength冷热骤变试验thermal shock test环境试验炉Environmental chamber盐雾实验salt spray test绝缘电阻测试验仪Insulating resistance meter内应力internal stress疲劳fatigue蠕变creep试样specimen撕裂强度tear strength缩痕shrink mark, sink mark耐久性durability抽样sampling样品数量sample sizeAQL Acceptable Quality level批量lot size抽样计划sampling planOC曲线operation curve试验顺序sequence of tests环境温度ambient temperature可焊性solderability阻燃性flame resistance一、组织机构及职位XX电子有限公司XX Electronics CO., Ltd 总经理办公室General manager’s office企管部Enterprise management department (EM)行政部Administration department (AD)销售部Sales department (SD)财务部Financial department (FD)技术部Technology department (TD)物控部Production material control department (PMC)生产部Production department(PD)模具部Mold manufacturing department, Tooling manufacturing department (TM)品管部Quality Assurance department (QA) 冲压车间Stamp workshop, press workshop 注塑车间injection workshop装配车间Assembly workshop模具装配车间Mold and die Assembly workshop金属加工车间metal machine workshop电脉冲车间Electric discharge process workshop线切割车间wire cutting process workshop工磨车间Grinding workshop总经理General manager (GM)副总经理Vice-general manager经理manager董事长president副董事长Vice-presidentXX部门经理Manager of XX department主任、主管supervisor拉长Line leader组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant二、产品连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压rated voltage额定电流rated current接触电阻contact resistance绝缘电阻insulation resistance超声波焊接ultrasonic welding耐压withstand voltage针pin物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity接触长度contact length接触件电镀层contact plating接触压力contact pressure接触件中心距contact space接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring多层印制电路Multilayer printed circuit焊盘pad图形pattern间距pitch负极Negative pole正极positive pole回流Reflow原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board 表面安装surface Mounting翘曲warp，bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance。