管道方案(中英文对照版)

合集下载

管道综合材料中英文对照表

管道综合材料中英文对照表

管道综合材料中英文对照表PIPE.SMLS 无缝钢管
PIPE.EFW 焊接钢管
90.ELBOW.LR 90度长半径弯头(R=1.5D)
90.ELBOW.SR 90度短半径弯头(R=1.0D)
45.ELBOW.LR 45度长半径弯头(R=1.5D)
TEE 三通(包括等径三通和异径三通)
CAP 管帽
REDUCER.CON 同心异径管
REDUCER.ECC 偏心异径管
HALF.COUPLING 半拷贝伦
OLET.WELDOLET 对焊鞍座
FLANGE.WN 带颈对焊法兰
BLIND.FLANGE 盲板法兰(法兰盖)
VALVE.GATE 闸阀
VALVE.GLOBE 截止阀
VALVE.BALL 球阀
VALVE.BUTTERFLY 蝶阀
VALVE.CHECK 止回阀
VALVE.PISTON.CHECK 升降式止回阀
VALVE.SWING.CHECK 旋启式止回阀
VALVE.NEEDLE 针形阀
GASKET 垫片
OCTAGONAL.RING.GASKET 八角型环垫片
STUD.BOLTS/HEAVY.HEX.NUTS 螺柱/螺母
RF 凸台面密封面
RJ 环槽面密封面
SW 承插焊
BW 对焊
WAFER 对夹
CL 、LB表示磅级例如:CL600表示压力等级为600LB(磅)FLEX.HOST 金属软管
GASKET.SPIRAL-WOUND 金属缠绕垫。

管道中英文对照表最全的

管道中英文对照表最全的

62
内外定位环
Inner ring and outer ring
IR/OR
63
内定位环
Inner ring
IR
64
外定位环
Outer ring
OR
65
螺栓
Bolt
B
66
螺柱
Stud bolt
SB
67
螺母
Nut
NU
68
花蓝螺母
Turnbuckle
TB
69
垫圈
Washer
WSR
70
弹簧垫圈
Spring washer
79
安全阀
Safety valve
SV
80
减压阀
Pressure reducing valve
RV
81
蒸汽疏水阀
Steam trap
ST
82
泄压阀
Pressur relief valve
PRV
83
呼吸阀
Breather valve
BV
84
针形阀
Needle valve
NV
85
角阀
AV
86
隔膜阀
DV
87
Flat metallic gasket
FMG
58
齿形金属垫片
Solid metal serrated gasket
SMSG
59
透镜式金属环垫
Lens ring gasket
LER
60
八角形金属环垫
Octagonal ring gasket
OCR
61
椭圆形金属环垫
Oval ring gakset

管道工程中英文对照

管道工程中英文对照

工程管道英文缩写对照AA Anchor 固定ABS Absolute 绝对的AISI American Iron and Steel Institute 美国钢铁学会ANSI American National Standards Institute 美国国家标准学会API American Petroleum Institute 美国石油学会APPROX Approximate 大约,近似的ASB Asbestos 石棉ASME *American Society Of Testing Material 美国机械工程师协会ASSY *Assembly 装配,组装ASTM *American Society OfTesting Material 美国材料实验协会ATM *Atmosphere 大气压AWG *American Wire Gage 美国线规AWS *American Wel**** Society 美国焊接协会AWWA *American Water WorksAssociation 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer 买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt Circle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖(帽)BE Beveled End (for wel****) 坡口(焊接用)B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Battery Limit 装置区边界BF Blind Flange 法兰盖BLD Blind 盲板BLDG *Buil**** 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端.平端BV Butterfly valve 蝶阀BWG * Birmingham Wire Gage 伯明翰线规BW Butt Weld 对焊CC Cap 管帽C-C Center to Center 中至中C-E Center to End 中至端面C-F Center to Face 中至面CH-OP Chain Operated 链条操纵的CH.PL Checkered Plate 花纹钢管C.I *Cast Iron 铸铁CL *Class 英制压力等级,等级,种类CLEAR Clearance 间隙COD Continued on Drawing 接续图COL *Column 柱,塔CONC Concentric 同心的CONN Connection 连接,接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPLG Coupling 管接头,连轴节C.R. Concentric Reducer 同心异径管C.S. *Carbon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客C.V Check Valve 止回阀DDEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter 直径DIM *Dimension 尺寸DISCH *Discharge 出口,排出Diaphragm VELVE 隔膜阀DMF Double Male And Female 双重凹凸DN *Double Male And Female 公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DWG *Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Eccentric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高;立面ELL Elbow 弯头EQIOP Equipment 设备,装置EQUIV Equivalent 相当的E.R. Eccentric Reducer 偏心异经管ERW Electric Resistance Welded 电阻焊的EW Eye Washer & Shower 洗眼器及淋浴器EXP.JT Expansion Joint 膨胀节FFDN Foundation 基础FF Flat Faced Or Full Faced 全平面;满平面F-F Face To Face 面至面FGW Fusion Gas Wel**** 气熔焊FIG *Figure 图FL Floor 楼面FLEX TUBE Flexible Tube 挠性管FLG Flange 法兰FLGD Flanged 法兰式的FLGF Flanged Face 法兰面FOB Flat On Bottom 底面平FOT Flat On Top 顶面平FP Fix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG Fitting 管件FURND Furnished 提供的,装设的FW Field Weld 现伤焊GG Guide 导向GA *Gage 表,表压,规(线规)GALV *Galvanize 镀锌GL Ground Level 地面GLV Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten Arc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPLG Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Hard Alloy Face on阀内件(阀心)为Valve Trim 硬质合金密封面HH Hand Pole 手孔HOR Horizontal 水平的H.P *High Pressure 高压HS Hose Station 软管IID *Inside Diameter 内径IN *Inch 英寸INS Insulation 隔热INST Instrument 仪表INV Invert (inside bottom of pipe) 管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图(空视图)I.S.B.L Inside Battery Limit 装置边界内恻ISNS Inside screw & Non-rising Stem 内螺纹非升杆ISRS Inside screw & Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开(起)螺栓LLC Locked Closed 在关闭状态下锁定LEP Large end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L.H.THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint Flange 松套法兰LO Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue & Groove 大椎槽MMATL Material 材料MAX Maximum 最大MB Machine Bolt 机器螺栓(单头)MF Male and Female 凸和凹MFG Manufacture 制造MF *Manufacture 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Minimum 最小MJ Mechanical Joint 机械接头M.L Match Line 连续线MSS * Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. 美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Minimum Wall 最小壁厚M.W. Mineral Wool 矿(物)棉NN *North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开*Number号;数量NO INS No Insulation 不隔热NOM Nominal 公称的;额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹Pipe ThreadNS Nominal Size 公称直径NV Needle Valve 针形阀OOD *Outside Diameter 外径OET One end Threaded 一端带螺纹OR Outside Radius 外半径ORF Orifice 孔板ORIENT Orientation 方位OS & Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖PP Plug 堵头PAP Piping Arrangement Plan 管道布置平面图PB Pressure Seal Bonnet 压力密封的阀盖P-B Plain End –Bevel End 平端—坡口端PC Pressure Seal Cap 压力密封的阀帽P.C.D. Pitch Circle Diameter 节圆直径PE Plain End (not beveled) 平端(无坡口)PF Platform 平台PID Piping & Instrument Diagram管道及仪表流程图PN *Nominal Pressure 公称压力PN Plant North 工厂北向POS point of Support 支承点P-P Plain End—Plain End 两端为平端PREP Preparation 加工准备PSIA *Pounds Per Square InchAbsolute 磅/PSIG Pounds Per Square Inch Gage 磅/PT Point 点PTFE *Polytetrafluoroethylene聚四氟乙烯PT.NO Part No. 件号PV Plug Valve 旋塞阀PVC *Poly Vinyl Chloride 聚氯乙烯QQTY *Quantity 数量RR *Radius 半径RED Reducer 异径管REF Reference 参考REINF Reinforce 加强REQD Required 需要;申请REV *Revision 修改RF Raised Face 凸面RG Ring Gasket 环形垫片R.H.THD Right Hand Thread 右螺旋RJ Ring Joint 环垫接头RO Restriction Orifice 限流孔板RPM *Revolutions Per Minute 转/分RPS *Revolutions Per Second 转/秒RS Resting Support 支承架,滑动架RTJ Ring Type Joint(见RJ)RV Relief Valve 安全泄液阀SS *South 南S Spring 弹簧(管架用)SAW (Automatic)Submerged Arc Wel**** 自动埋弧焊SB Stud Bolt 双头螺栓SB Screwed Bonnet 螺纹阀盖SC Sample Cooler 取样冷却器SCH *Schedule 管壁厚系列号SCRD Screwed 螺纹SEP Small end Plain 小端为平的SET Small end Threaded 小端带螺纹SF Semi-Finished 半光SG Sight Glass 视镜SH Surface Hard Facing 硬质密封面SK Sketch 草图SMAW Shielded Metal Arc Wel**** 有保护的金属电弧焊SMLS Seamless 无缝SN Swaged Nipple 异径短管SO Slip – On 滑套SOF Slip – On Flange 滑套法兰SPEC *Specification 规定,说明SPL Sound Pressure Lever 升压水准SQ *Square 方的,平方SR Shout Radius 短半径SRE Short Radius Elbow 短半径弯头SS *Stainless Steel 不锈钢ST Steam Trap 蒸汽疏水阀STD *Standard 标准STG Small Tongue & Groove 小椎槽面STL *Steel 钢STM Steam 蒸汽STM.TR Steam Tracing 蒸汽拌热SUCT Suction 吸入口SV Safety Valve 安全泄气阀SW Socket Weld 承插焊SWG Swage 锻造,模锻SWMG Swing Type 旋启式SYM Symmetrical 对称的TT Tee 三通TE Threaded End 螺纹端TEMP *Temperature 温度TG Tongue & Groove 椎槽THD *Threaded 螺纹的THK *Thickness 厚度TL Tangent Line 切线TN True North 真实北向TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶TOS Top of Support 支架顶面Top of Steel 钢结构顶面TYP Typical 典型的UUB Union Bonnet 带活接头的阀盖UC Union Cap 带活接头的阀帽UN Union 活接头VV Valve 阀VAC Vacuum 真空VAR Variable 可变的VERT Vertical 垂直的VOL *Volume 卷,册,容量,体积WW *West 西WB Weld Branch 焊接支管WC Weld Cap 焊接管帽WD Width 宽度WE Weld End 焊接端WL Wel**** Line 焊接线WN Wel**** Neck 对焊法兰(颈部)WNF Weld Neck Flange 对焊法兰WP Working Pressure 工作压力W.P. Working Point 工作点WT Wall Thickness 壁厚Weight 重量XXH Extra Heavy 加强的,加厚的XXH Double Extra Heavy 双倍加强(厚)的XS Extra Strong 加强的XXS Double Extra Strong 双倍加强的YYP Yield Point 屈服点。

管道中英文对照表最全的

管道中英文对照表最全的

带颈法兰
STRAINER
过滤器
BLIND
盲法兰(盲板)
BUCKET-TYPE STRAINER
篮式\桶式过滤器
FLANGE LAP JOINT
松套法兰
T-TYPE STRAINER
T型过滤器
LAP JOINT STUB END
翻边(与松套法兰配对用Y)-TYPE STRAINER
Y型过滤器
BREATHER-VALVE
减压阀、泄压阀、溢流阀
V#7596.7591.6596.6590.8592 金属缠绕垫
PRESSURE-GAUGE-VALVE
泄压阀
V#N510.520
金属类垫
DIAPHRAGM-VALVE (DV)
隔膜阀
3-WAY VALVE
三通阀
BOLT
螺栓
FLOWMETER/FT
流量计,流量阀
STUD BOLT
浮球式疏水器
V#6500.6501.6502.6500AC
非石棉垫
FLOAT TYPE TRAP
浮式疏水器
V#7010.V#7020.V#7026.V#7GP61 四氟垫
RELIEF-VALVE
减压阀、泄压阀、溢流阀
V#7030.V#7031.V#7035
四氟包覆垫
RV PRESSURE-VALVE
CONNECTION ORIENTATION 管口方位
PBE是Plain Both End的缩写 两头都是平口(焊接) GTAW
钨极气体保护焊(全氩)
TOE&POE
一端平口,另一端螺纹 GTAW+SMAW
保护焊+电焊(氩电联焊)
SAW

工艺管道中英文对照

工艺管道中英文对照

工艺管道中英文对照管材规格:1.管材数量:2个8英寸的管道。

2.管道中英文对照:PIPES-STDBEA106-B(EJ=1.00)SMLSASME-B36.1M。

3.管壁厚端部材质:无缝标准号。

4.假管备注:与主管相同。

5.90度长半径弯头数量:4个。

6.90度长半径弯头材质:STDBWA234-WPB-SSMLSASME-B16.9.7.90度长半径弯头壁厚端部材质:无缝标准号。

8.材质有A106B、P11、P22、A691、TP304H、A.管配规格:1.材质有A234-WPB-S=A106、A691;A234-WP11=P11;A234-WP22=P22.2.STR TEE数量:1个。

3.STR TEE规格:CL3000SWA105FORGEASME-B16.11,等径三通壁厚承插焊材质铸造标准号。

4.RED XXX数量:3个。

5.RED TEE规格:11.07×S-XXS BW A234-WP22 CL1-S SMLS ASME-B16.9,异径三通壁厚端部材质无缝标准号。

6.ECC SWAGES数量:6个。

7.ECC SWAGES规格:80×S-80 PE×PE A234-WPB—S SMLS MSS-SP-95,偏心大小头壁厚端部材质无缝标准号。

8.CON REDUCER数量:2个。

9.CON REDUCER规格:25.8×14.02mm BW A234-WP22 CL1-S SMLS ASME-B16.9,偏心大小头壁厚端部材质无缝标准号。

10.SOCKLET数量:1个。

11.SOCKLET规格:CL6000SWA182-F22CL3FORGEMSS-SP-97,承插支管台壁厚端部材质锻炼标准号。

12.SMLS(无缝)WELD(焊接)数量:4个。

13.45 DEG(45)数量:2个。

14.CON SWAGE数量:1个。

15.ECC REDUCER数量:1个。

管道中英文对照表

管道中英文对照表

RING SIPHON
红吸管
SS-EFW PIPE
不锈钢有缝管
LATROLET
斜接支管台
THREDOLET CL3000 FNPT
内螺纹支管台
SOCKOLET CL3000 SW
承插管台
PRESSURE GAUGE VALVE TOE是Threaded One End缩写 POE是Plain One End的缩写
铜外丝堵头
FNPT
内螺纹
MNPT
外螺纹
SW/FNPT
套焊/螺纹
BOLTΒιβλιοθήκη 螺栓STUD BOLT
双头螺栓
***-H
保温管线
***-C
保冷管线
***-P
防烫管线
***-N
不需绝热管线
INSULATION
绝热
TYPE
类型
THICK
厚度
**-C3C-**
碳钢CS
**-C5S-**
304
**-B2S-**
304
VALVE GV-GATE TV-GLOBE CV-CHECK BV-BALL NV-NEEDLE PV-SPECIAL FV-BUTTERFLY XV-CORTROL STRAINER
PSV
管道术语中英文对照表
中文
英文
中文
美标 管道 有缝管、焊管 无缝管 短管 软接头(金属软管) 弯头 弯头 弯头 1.0D 弯头 1.5D 三通 丝扣三通 套焊三通 对焊三通 等径三通 异径三通 对焊大小头 偏心大小头 同心大小头 套焊大小头 活套 法兰 平面法兰 凸面法兰 松套法兰 带颈法兰 盲法兰(盲板) 不锈钢 牙接头 单头接头 双接头 承插管座(半接头) 对焊管座 螺纹管座 束接(管接头) 半接头 全接头 管帽 管帽(丝牙) 管帽(套焊) 管帽(对焊) 垫片 聚四氟乙烯石棉垫 无石墨压缩白石棉垫 石棉垫 阀门 闸阀 截止阀 止回阀 球阀 针阀 特殊阀 蝶阀 控制阀 过滤器 安全阀

管道制作(中英文对照版)

管道制作(中英文对照版)
1.1.5Jacketed piping, tubing, orifice runs; lined or coated metals and fabrication by methods other than threading, welding, bending and flanging are not within the scope of this specification.
“批”为同一规格、同一炉号(如焊接,则应用同批焊条、同炉号焊丝和同批焊剂)、同一制度热处理(连续炉或间歇炉温差±14℃(25℉)并配备有完整的温度记录)的材料。
1.2.2“Field Fabricated Piping” shall be defined as all piping assemblies and completely erected piping systems fabricated by the Supplier and/or its field piping erection contractor who has the responsibility for the completely erected piping system. It includes both “in-position” welds and any fabricating operations carried out at the job site.
Contract Title合同标题
Shanghai Secco Petrochemicals Company Limited
上海赛科石油化工有限责任公司
Integrated Project Management Team
一体化项目管理组
Caojing,Shanghai, P R China

管道工程中英文对照

管道工程中英文对照

工程管道英文缩写对照AA Anchor 固定ABS Absolute 绝对的AISI American Iron and Steel Institute 美国钢铁学会ANSI American National Standards Institute 美国国家标准学会API American Petroleum Institute 美国石油学会APPROX Approximate 大约,近似的ASB Asbestos 石棉ASME *American Society Of Testing Material 美国机械工程师协会ASSY *Assembly 装配,组装ASTM *American Society OfTesting Material 美国材料实验协会ATM *Atmosphere 大气压AWG *American Wire Gage 美国线规AWS *American Wel**** Society 美国焊接协会AWWA *American Water WorksAssociation 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer 买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt Circle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖(帽)BE Beveled End (for wel****) 坡口(焊接用)B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Battery Limit 装置区边界BF Blind Flange 法兰盖BLD Blind 盲板BLDG *Buil**** 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端 . 平端BV Butterfly valve 蝶阀BWG * Birmingham Wire Gage 伯明翰线规BW Butt Weld 对焊CC Cap 管帽C-C Center to Center 中至中C-E Center to End 中至端面C-F Center to Face 中至面CH-OP Chain Operated 链条操纵的CH.PL Checkered Plate 花纹钢管C.I *Cast Iron 铸铁CL *Class 英制压力等级,等级,种类CLEAR Clearance 间隙COD Continued on Drawing 接续图COL *Column 柱,塔CONC Concentric 同心的CONN Connection 连接,接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPLG Coupling 管接头,连轴节C.R. Concentric Reducer 同心异径管C.S. *Carbon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住 CUST Customer 客C.V Check Valve 止回阀DDEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter 直径DIM *Dimension 尺寸DISCH *Discharge 出口,排出Diaphragm VELVE 隔膜阀DMF Double Male And Female 双重凹凸DN *Double Male And Female 公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DWG *Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Eccentric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高;立面ELL Elbow 弯头EQIOP Equipment 设备,装置EQUIV Equivalent 相当的E.R. Eccentric Reducer 偏心异经管ERW Electric Resistance Welded 电阻焊的EW Eye Washer &Shower 洗眼器及淋浴器 EXP.JT Expansion Joint 膨胀节FFDN Foundation 基础FF Flat Faced Or Full Faced 全平面;满平面F-F Face To Face 面至面FGW Fusion Gas Wel**** 气熔焊FIG *Figure 图FL Floor 楼面FLEX TUBE Flexible Tube 挠性管FLG Flange 法兰FLGD Flanged 法兰式的 FLGF Flanged Face 法兰面FOB Flat On Bottom 底面平FOT Flat On Top 顶面平FP Fix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG Fitting 管件FURND Furnished 提供的,装设的FW Field Weld 现伤焊GG Guide 导向GA *Gage 表,表压,规(线规)GALV *Galvanize 镀锌GL Ground Level 地面GLV Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten Arc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPLG Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Hard Alloy Face on 阀内件(阀心)为Valve Trim 硬质合金密封面HH Hand Pole 手孔HOR Horizontal 水平的H.P *High Pressure 高压 HS Hose Station 软管 IID *Inside Diameter 内径IN *Inch 英寸INS Insulation 隔热INST Instrument 仪表INV Invert (inside bottom of pipe)管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图(空视图)I.S.B.L Inside Battery Limit 装置边界内恻ISNS Inside screw &Non-rising Stem 内螺纹非升杆ISRS Inside screw &Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开(起)螺栓LLC Locked Closed 在关闭状态下锁定LEP Large end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L. H.THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint Flange 松套法兰LO Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue &Groove 大椎槽MMATL Material 材料MAX Maxim um 最大MB Machine Bolt 机器螺栓(单头)MF Male and Female 凸和凹MFG Manufacture 制造MF *Manufacture 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Minimum 最小MJ Mechanical Joint 机械接头M.L Match Line 连续线MSS * Manufacturers Standardization Society of the Valve and Fittings Industry, Inc.美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Minimum Wall 最小壁厚M.W. Mineral Wool 矿(物)棉NN *North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开 *Number 号;数量NO INS No Insulation 不隔热NOM Nominal 公称的;额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹Pipe ThreadNS Nominal Size 公称直径NV Needle Valve 针形阀OOD *Outside Diameter 外径 OET One end Threaded 一端带螺纹OR Outside Radius 外半径ORF Orifice 孔板ORIENT Orientation 方位OS &Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖 PP Plug 堵头PAP Piping Arrangement Plan 管道布置平面图 PB Pressure Seal Bonnet 压力密封的阀盖P-B Plain End -Bevel End 平端一坡口端PC Pressure Seal Cap 压力密封的阀帽 P.C.D. Pitch Circle Diameter 节圆直径PE Plain End (not beveled)平端(无坡口)PF Platform 平台PID Piping &Instrument Diagram 管道及仪表流程图 PN *Nominal Pressure公称压力PN Plant North 工厂北向POS point of Support 支承点P-P Plain End —Plain End 两端为平端PREP Preparation 加工准备PSIA *Pounds Per Square Inch Absolute 磅 /PSIG Pounds Per Square Inch Gage 磅 /PT Point 点PTFE *Polytetrafluoroethylene 聚四氟乙烯 PT.NO Part No. 件号PV Plug Valve 旋塞阀PVC *Poly Vinyl Chloride 聚氯乙烯QQTY *Quantity 数量RR *Radius 半径 RED Reducer 异径管 REF Reference 参考 REINF Reinforce 加强 REQD Required 需要;申请 REV *Revision 修改 RF Raised Face 凸面 RG Ring Gasket 环形垫片 R.H.THD Right Hand Thread 右螺旋 RJ Ring Joint 环垫接头 RO Restriction Orifice 限流孔板 RPM *Revolutions Per Minute 转 / 分 RPS*Revolutions Per Second 转 / 秒 RS Resting Support 支承架,滑动架 RTJ Ring Type Joint (见 RJ) RV Relief Valve 安全泄液阀SS *South 南S Spring 弹簧(管架用)SAW (Automatic)Submerged Arc Wel**** 自动埋弧焊 SB Stud Bolt 双头螺栓SB Screwed Bonnet 螺纹阀盖 SC Sample Cooler 取样冷却器 SCH *Schedule 管壁厚系列号 SCRD Screwed 螺纹SEP Small end Plain 小端为平的 SET Small end Threaded 小端带螺纹 SF Semi-Finished 半光 SG Sight Glass 视镜SH Surface Hard Facing 硬质密封面SK Sketch 草图SMAW Shielded Metal Arc Wel**** 有保护的金属电弧焊 SMLS Seamless 无缝SN Swaged Nipple 异径短管SO Slip -On 滑套SOF Slip -On Fla nge 滑套法兰SPEC *Specification 规定,说明SPL Sound Pressure Lever 升压水准SQ *Square 方的,平方 SR Shout Radius 短半径SRE Short Radius Elbow 短半径弯头 SS *Stainless Steel 不锈钢 ST Steam Trap 蒸汽疏水阀STD *Standard 标准STG Small Tongue &Groove 小椎槽面 STL *Steel 钢STM Steam 蒸汽STM.TR Steam Tracing 蒸汽拌热 SUCT Suction 吸入口SV Safety Valve 安全泄气阀 SW Socket Weld 承插焊SWG Swage锻造,模锻SWMG Swing Type 旋启式 SYM Symmetrical 对称的 TT Tee 三通TE Threaded End 螺纹端 TEMP *Temperature 温度 TG Tongue &Groove 椎槽 THD *Threaded 螺纹的 THK *Thickness 厚度 TL Tangent Line 切线 TN True North 真实北向TOC Top of Concrete 混凝土北向TOP Top of pipe 管顶TOS Top of Support 支架顶面 Top of Steel 钢结构顶面 TYP Typical 典型的 UUB Union Bonnet 带活接头的阀盖 UC Union Cap 带活接头的阀帽 UN Union 活接头VV Valve 阀VAC Vacuum 真空VAR Variable 可变的VERT Vertical 垂直的VOL *Volume 卷,册,容量,体积WW *West 西WB Weld Branch 焊接支管WC Weld Cap 焊接管帽WD Width 宽度WE Weld End 焊接端WL Wel**** Line 焊接线WN Wel**** Neck 对焊法兰(颈部)WNF Weld Neck Flange 对焊法兰WP Working Pressure 工作压力W.P. Working Point 工作点 WT Wall Thickness 壁厚 Weight 重量XXH Extra Heavy 加强的,加厚的XXH Double Extra Heavy 双倍加强(厚)的XS Extra Strong 加强的XXS Double Extra Strong 双倍加强的 YYP Yield Point 屈服点编丐缩场啰文名称龙艾名称b管子及管件1.1P 管子Pipe1.2EL 弯头ElbowL2t 1 LLL 长半控缚头Long radius plb™1.2.2LLS 虬半轮弯头Short radius elbc*1.2.3亚―斜接骂犬[卜来艘弯头)Milrc oJbow1.2.4 REL 异径弯头Reducing elbow1.3T 三通TeeL 3+1 LT 斜二通LalerM t^eL3.2 RT 异径三通Reducing leeL4 K畀径管接头(大小头)Reducer1.4.1CR同心异径營接头(同心人小头丨Concentric reducer* \.A.2 ER偏心异径管接头「偏心大小头)Eccentric reducer 1.5 CPL 管箍CouplingL5. 1 FCPL 双头管箍Full couplingL5.2 HCPL 单头背箍Half couplingL 5. 3 BCPL 异径骨JS Reducing couplingL6 BU内外螺St接头Bushing1.7LN 活接头Union1.8HC 软管接头Hose coupler1.9SE圄边短节Stub end1* 10 NIP 炬节 Pipe nipple or straight nipple1.10.1SNIP 异径短节Swaged nippleLU CP 1 封头)Cap1.1? PL 堵i 箧墳〉Plug1.13BLK 肓板BlankL 13. 1 SB 8 'y-HSpectacle blind (blank)1.14RP 补强板Reinforcing pad2.法兰2.1PLG 法兰Flange2.L 1 WNF 对埠法兰Wold ing no^k [ 1 nngo2.1.2冏F 平焊法兰Slip-on flanEe2.1.3SWF 承插焊法兰Sockel weldin; flange2・ IL 4 T 螺纹法兰Threaded llangp2*1- S LJ 松套法兰Lapped joint fhinge2* L 6 IOF 显径法竺Reduc i ng Clangs2.L7 BF 法兰葢(口法二丿Blind rinngc2*2 FSF 注一磴対面Flange scaling face2.2.1FF 金平而Flat face2, 2.2RF 凸合面Raised face2T2. 3 MEF 凹凸面Male and female lace2.2.4 LF rinn徒瞪1曽畑氓2.比斤仙凸面Male face2.2. 6 RJ 环连接面Ring joint face2.N7 Tt-櫛槽iE Tnnguf* nnd gr^cive (ice2.2, H TF 挥面Tongue face2*2.9 GF 摘面Groove fnce3 •垫片3.1G 热片G般keL3.1. 1 NMG 非佥属垫片Non me la 11 ic gasket3,L L 1 AG 石棉隸:片Asbest os gasket3.LL2 RG 椽胶垫片Rubber gasket3.L 1. 3 TEG聚四龜乙烯包复塑片PUT envelop gasket3,L 2 SMG 半金属犁:片Semiiaetallic gasket3.1.2. 1 MJG 金屈ti 地片Me tn jacket gasket3.L 2. S SiG 鍵境式垫片Spiral wound gasket3. L 3 MG 金属敝片Metal Lie gasket3, L/l 1 FMS 金屈平热片Flat metallic gasket3. L, 3, 2 SMS(i 崗冊金属给片Mil id metal serraled gasket 3丄3* 3 LER透愎式金属环垫Lens ring gasket3.1.3.t OCli 八角形金属环垫Octagonal ring gasket3.1.3, 5 OVR IB圆形益属环墊Oval ring gaske t3.1. 3, fi IR/OR 内外定位环inner ring and outer ring3”L.£7 IK 内定fit环Inner ring3.1.3,8 OR 外定位环OutEr ring4 ,坚固件4.1 B 蝶栓Holt4.1.1SB 螺栓Stud bolt4.2籾*ffi母Nut4.3JB 花蓝螺母Tumbuckie4.4WSK 地阉Washer4^ 4^ 1 SWSR 弹黃呈圈Spring washer「阀门fk 1 CW |剤阀Gale va I\r p 5.2GL¥ 截止阀Globe valve。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

管道工程施工质量管理工作细则PIPING CONSTRUCTION QUALITY MANAGEMENT DETAIL RULES目录Content1.0 编制目的及适用范围Purpose for Preparation and Scope of Application2.0 编制原则Principles for Preparation3.0执行标准及有关规定Applicable Standards and Relevant Regulations3.1 中国政府的相关法规和政策Relevant laws, regulations and policies issued by Chinese government: 3.2 SECCO项目IPMT质量体系有关文件Documentation related to IPMT quality system of SECCO project: 3.3 SECCO项目IPMT规定和要求IPMT regulations and requirements of SECCO project:3.4 施工验收标准及规范Standards and codes for construction acceptance:4.0 冲突和协调Conflict and Coordination5.0 专业技术经理与专业工程师Specialist Technical Manager and Specialist Engineer5.1专业技术经理Specialist technical manager5.2 专业工程师Specialist engineer6.0 HSE7.0 施工过程中工程施工质量的控制Quality Control in the Process of Construction7.1 主要依据Main basis7.2 熟悉现场管理体系、建立工作接口Acquaintance with site management system and establishment ofworking interface7.3 技术准备Technical Preparations7.4 组织设计交底Organization Design Briefing7.5 图纸与设计文件会审Joint Check-up of Drawings and Design Documents7.6 审查施工组织设计和施工方案Check-up of Construction Organization Design and Construction Plan 7.7 施工过程的质量控制点的制定和检查程序Procedures for the Establishment and Inspection of Quality ControlPoints in the Construction Process7.8 施工过程中的质量控制Quality Control During the Construction Process7.8.1 原材料的检查与验收原则Principles for the Inspection and Verification of Raw Materials7.8.2 管子抽检的内容和比例Contents and Percentage of Pipe Spot-check7.8.3 其他管道组成件抽检的内容和比例Spot-check Contents and Percentage of Other Pipe Components7.8.4 阀门的检验与试验(包括管道视镜、过滤器及阻火器检验)Valve Inspection and Experiment (Including the inspection of pipe signtglass, strainer and flame arrestor)7.8.5 采用的主要管道器材标准(规范)Major Piping Specifications Standards (or codes)7.8.5.1 材料标准Material Standards7.8.5.1.1 无缝钢管Seamless Steel Pipe7.8.5.1.2 焊接钢管Welded Steel Pipe7.8.5.1.3 管件Pipe fittings7.8.5.1.4 联接件Pipe joints7.8.5.1.5 阀门Valves7.8.5.2 应用规范Application specification7.8.5.2.1 管子Pipe7.8.5.2.2 管件Pipe fittings7.8.5.2.3 联接件Pipe joints7.8.5.2.4 阀门Valves7.8.6 管道防腐Pipingcorrosion prevention7.8.7 管道的预制加工工艺Pre-fabrication process for pipe7.8.8 碳素钢管道焊接、热处理及质量检查Welding, heat treatment and quality inspection for carbon steel pipe 7.8.9 阀门安装Valve installation7.8.10 低温材料检验及安装Cryogenic material inspection and installation7.8.11 静电接地安装Static grounding erection7.8.12 管道系统试验、吹除与清洗Test, purging and cleaning for piping system7.8.13 工程中间交接Engineering intermediate takeover7.8.14 竣工验收Completion acceptance7.9 专业工程师应保存的资料Documents to be retained by specialist engineer附录1: 管道安装工程质量控制点Appendix 1 Quality Control Points for Piping Installation Project附录2:工业管道施工管理台帐Appendix 2 I ndustrial Piping Construction Management Record Book1.0编制目的及适用范围:Purpose for Preparation and Scope of Application1.1 本规定适用于上海SECCO 90x104t/a乙烯项目(以下简称SECCO项目)的现场施工质量管理工作。

These stipulations are applicable to the site construction quality management of Shanghai SECCO 90x104t/a Ethene Project (hereinafter referred to as SECCOproject).1.2 本规定是为了明确SECCO项目的现场施工质量管理工作的职责、工作内容、工作流程、方法以及设计、采购、施工的协调,推行现代化、科学化、规范化的项目管理模式而编制的。

These stipulations are prepared for the purpose of defining the responsibilities, working contents, operating process and procedures for the site constructionquality management of the SECCO project and for coordination among thedesign, procurement and construction, so as to pursue the modernized, scientific and standardized mode for project management.2.0 编制原则Principles for Preparation2.1 本细则在项目质量管理目标合理分解、项目质量管理组织已经确立的前提下,以项目的规律效应性和操作实用性为原则编制的。

These rules are prepared on the principle of the law effectiveness and operating practicability of the project, under the precondition that the objectives of theproject quality management have been reasonably decomposed and theorganization of project quality management has been established.2.2 本细则注意到质量检验评定中工程划分与WBS分解结构在施工管理中的内在联系,我们强调将两者的划分尽量统一。

These rules have given full attention to the inherent links between the projectcomponent division in the quality inspection and evaluation and WBSdecomposed structure in the construction management. We emphasize that the two divisions should be unified as far as possible.2.3为加强主动控制的力度,本细则建议建立专业施工管理台帐,将施工质量控制纳入现场施工管理体系,专业工程师应参加重要的材料和设备的招标订货会议,了解产品质量、合同技术要求、厂家售后服务及到货情况。

以便在施工管理台帐中列出每月到货清单,使材料报检及工程报检工作系统化。

In order to strengthen the power of active control, it is recommended by theserules that a specialized construction management record book is established tointegrate the construction quality control into site construction managementsystem. It is also suggested that specialist engineers should participate in thebidding and ordering meetings for important materials and equipment to getacquainted with the product quality, the technical requirements of the contract, after-sale service provided by manufacturer and the deliverystatus. And then it is possible to put the monthly goods-arrival list in theconstruction management record book and to realize the systematization ofmaterial acceptance and engineering inspection procedures.3.0执行标准及有关规定Applicable Standards and Relevant Regulations3.1 中国政府的相关法规和政策:Relevant laws, regulations and policies issued by Chinese government:压力管道安全管理和监察规程Regulations for Pressure Piping Safety Management and Supervision压力管道安装安全质量监督检验规则Rules for Pressure Piping Installation Safety and Quality Supervision andInspection3.2 SECCO项目IPMT质量体系有关文件:Documentation related to IPMT quality system of SECCO project:规划管理计划(PMP) PL-00-IIJ-PM-0001Program Management Plan (PMP)质量管理策略ST-00-IIJ-QU-0001Quality Management Strategy质量管理组织体系PL-00-IIJ-QU-0002Quality Management Organization System工程质量管理规定PR-00-CIJ-QU-0001Regulations for Project Quality Management质量审核程序PR-00-IIJ-QU-0001Quality Check Procedures承包商质量(QA/QC)标准SD-00-IIJ-QU-0001Quality Assurance/Quality Control (QA/QC) Standard for Contractors施工管理细则Construction Management Detail Rules3.3 SECCO项目IPMT规定和要求:IPMT regulations and requirements of SECCO project:装置布置原则PH-00-TSC-PP-0001Plant Layout Philosophy管道材料规定SD-00-TSC-PP-0001Specifications for Piping Materials工艺及公用工程管道设计要求SD-00-TSC-PP-0002Process and Utility Piping Design Requirements地下钢管涂层及包覆标准SD-00-TSC-PP-0003Standard for Coating and Wrapping of Underground Steel Pipe管道制作SD-00-TSC-PP-0004Fabrication of Piping蒸汽伴热管要求SD-00-TSC-PP-0005Steam Tracing Piping Requirements管道支撑标准SD-00-TSC-PP-0007Standard for Piping Support管道柔性--设计标准SD-00-TSC-PP-0008Piping Flexibility—Design Criteria管道的现场试压SD-00-TSC-PP-0009Field Pressure Testing of Piping隔离材料及应用—热保温SD-00-TSC-PP-0010Insulation Materials & Application ------Hot Service隔离材料及应用—冷保温SD-00-TSC-PP-0011Insulation Materials& Application------Cold Service管道及设备的隔音保护SD-00-TSC-PP-0012Sound ControlInsulation of Piping and Equipment标准详图SD-00-TSC-PP-0013Standard Detail Drawing管道焊接标准SD-00-TSC-MS-0025Standard for Piping Welding3.4 施工验收标准及规范:Standards and codes for construction acceptance:石油化工剧毒、可燃介质管道工程施工及验收规范SH3501-2001 Specification for Construction and Acceptance of Hypertoxic and Combustible Medium Piping Engineering in Petrochemical Industry工业金属管道工程施工及验收规范GB50235-97 Code for Construction and Acceptance of Industrial Metallic Piping现场设备、工业管道焊接工程施工及验收规范GB50236-98 Code for Construction and Acceptance of Field Equipment and Industrial PipingWecontractorng工业安装工程质量检验评定统一标准GB50252-94Unified Standard for Checking and Evaluating the Quality of Industrial Installation Engineering工业金属管道工程质量检验评定标准GB50184-93 Standard for Checking and Evaluating the Quality of Industrial Metallic Piping Engineering工业管道、设备绝热工程施工及验收规范GBJ126-89C ode for Construction and Acceptance of Industrial Piping andEquipmentThermalInsulationEngineering石油化工工程焊接工艺评定SHJ509-88 Welding ProcedureQualification for Petrochemical Engineering石油化工钢制管道工程施工工艺标准SH3517-2001Construction Process Standard for Petrochemical Steel Piping Engineering阀门检验与管理规程SH3518-2000 Code forValve Inspection and Management石油化工钢制通用阀门选用、检验及验收SH3064-94 Selection, Inspection and Acceptance of Petrochemical General Steel Valves石油化工设备和管道涂料防腐蚀技术规范SH3022-1999 Technical Specification forthe Coating anticorrosion of Equipment and Piping in Petrochemical Industry石油化工企业设备管道表面色和标志SH3043-91 Equipment and Piping Surface Color and Marking for Petrochemical Industry 埋地钢质管道石油沥青防腐层施工及验收规范SYJ4020-88 Code for Construction and Acceptance of Petroleum Asphalt CorrosionProtection Layer for Undergrand Steel Piping工艺管道ASME B31.3-2002 Process Piping无损检测ASME Section V Nondestructive Examination焊接和钎焊评定ASME Section IXWelding and Brazing Qualification阀门检验及试验API Std 598Valve Inspection and Testing4.0冲突与协调Conflict and Coordination中国政府法规、SECCO项目规定、标准和规范(包括国内的和国外的): Laws and regulations issued by Chinese government and the stipulations, standards and codes of SECCO project (including home and foreign ones): 当在项目执行过程中,中国政府法规、SECCO项目规定及标准、规范间有矛盾时,执行的顺序应当是:中国政府法规、SECCO项目规定、标准和规范要求。

相关文档
最新文档