机床行业英语词汇_机械英语词汇
数控机床常用英语词汇
数控机床常用英语词汇1)计算机数值控制 (Computerized Numerical Control, CNC)用计算机控制加工功能，实现数值控制。
2)轴(Axis)机床部件可以沿着其作直线移动或回转运动基准方向。
3)机床坐标系( Machine Coordinate Systern )固定于机床上，以机床零点为基准笛卡尔坐标系。
4)机床坐标原点( Machine Coordinate Origin )机床坐标系原点。
5)工件坐标系( Workpiece Coordinate System )固定于工件上笛卡尔坐标系6)工件坐标原点( Wrok-piexe Coordinate Origin)工件坐标系原点。
7)机床零点( Machine zero )由机床制造商规定机床原点。
8)参考位置( Reference Position )机床启动用沿着坐标轴上一个固定点，它可以用机床坐标原点为参考基准9)绝对尺寸(Absolute Dimension)/绝对坐标值(Absolute Coordinates)距一坐标系原点直线距离或角度。
10)增量尺寸( Incremental Dimension ) /增量坐标值(Incremental Coordinates)在一序列点增量中，各点距前一点距离或角度值。
11)最小输人增量(Least Input Increment)在加工程序中可以输人最小增量单位。
12)命令增量(Least command Increment)从数值控制装置发出命令坐标轴移动最小增量单位。
13)插补(InterPolation)在所需路径或轮廓线上两个点间根据某一数学函数(例如：直线，圆弧或高阶函数)确定其多个中间点位置坐标值运算过程。
14)直线插补(Llne Interpolation)这是一种插补方式，在此方式中，两点间插补沿着直线点群来逼近，沿此直线控制刀具运动。
15)圆弧插补(Circula : Interpolation)这是一种插补方式，在此方式中，根据两端点间插补数字信息，计算出逼近实际圆弧点群，控制刀具沿这些点运动，加工出圆弧曲线。
数控机床常用英语词汇
数控机床常用英语词汇T WORD ERROR （T 码错误）LOW OIL LEVEL （油位低）SPINPLE FAULT （主轴故障）SPINDLE ALARM （主轴报警）EXTERNAL EMG STOP （急停按钮被按下）AC NOT READY （交流盘未准备好）SPINPLE LUBE FAULT （主轴润滑故障）T CODE ERROR （T代码出错，非法T代码）M CODE ERROR （M代码出错，非法M代码）SERVO NOT READY （伺服未准备好）NC NOT READY （NC没准备好）TURRET FAULT （转塔故障）TURRET LIMIT （转塔限位）DC 24V OPEN （直流24断开）+24V NOT READY （+24V没准备好）GRAR DRIFT （档位漂移）PLEASE AXIS RETURN HOME （轴未回零）PLEASE DRUM RETURN HOME （刀库未回零）AIRPRESS FAILURE （气压故障）UNCL TOOL FALL （松刀失败）AIR PRESSURE DROP （压缩空气压力过低）CLAMP TOOL FALL （夹刀失败）DRUM NOT PARKED （刀库未在原值）X ZERO POINT NOT REACHED （X 轴未回零）Y ZERO POINT NOT REACHED （Y 轴未回零）Z ZERO POINT NOT REACHED （Z 轴未回零）4TH ZERO POINT NOT REACHED （第4轴未回零）X AXIS OVERTRAVL （X轴超限）Y AXIS OVERTRAVL （Y轴超限）Z AXIS OVERTRAVL （Z轴超限）COUNTER SWITCH REEOR （计数开关故障）MASTERT RANSFER OVER TEMP 主变压器过热Z AXIS NOT AT FIRST REF POSITION（Z轴未在第一参考点）SPINDLE ORIENTATION FALLURE 主轴定向失败TOOL DESENT OR TOOL DATA REEOR（刀具数据错误）PLEASE UNLOAD THE TOOL ON SPRINELK（请卸下主轴上的刀）PLEASE LOAD TOOL ON APINDLE（请装上主轴上的刀）A AXIS UNCLAMP FAIL （A 轴松开失败）A AXIS CLAMP FAIL （A 轴夹紧失败）DRUM OUT TO APRONDLEIS FALL（刀库摆向换刀位失败）MG SWING OVERLOAD （刀库摆动过载）DRUM BACK PARK IS FALL（刀库摆回原始位失败）TURRENT MOTOR1 OVERLOAD （刀库移动电机过载）COOLANT MOTOR OVERLOAD 冷却泵过载DRUM ATC FAULT （自动换刀失败）TOOLS UNLOCKED （刀具未锁紧）BATTERY ALARM （电池报警）DRUM POSITION SWITCH ERROR（刀库位置检测开关故障）DRUM NOW NOT AT PARK 刀库未在原始位置IT DANGOU TO MOVE DRUM （刀库禁动）POT UO FAILOR POT NOT AT UP POSITION （刀套未在水平位）POT DOWN FAIL （刀套翻下动作失败）IT IS DANGOUR TO MOVE ARM 机械手禁动THE SPINDLE STATU IS ERROR 主轴状态错误ARM MOTOR OR ARM SWITCH FALL（机械手或机械手开关故障）CENTRE LUBRICATION FALL 中心润滑故障）THE WORK NOT CLAMPED （工件未夹紧）AUTO TOOL CHANGE FAULT （自动换刀失败）TOOL DATA OUT OF RANGE（指令刀具号超出范围）THE ORDER TOOL NOW IN SPINDLE（目标刀具在主轴上）THE THREE SPINDLE SWITCH FAULT（主轴上的接近开关）THE CENTRE COOLANT IS LOWER（刀具内冷泵液位过低）DRUM RETURN 1# POSITION FAULT（刀库自动回零失败）SPINDLE OVERLOAD （主轴过载）TURRENT MOTOR OVERLOAD（刀盘转动电机过载）CHIP CONVEYER OVERLOAD （拉屑器过载）HARD LIMIT OR SERVO ALARM（硬限位或伺服报警）NO LUB OIL （无润滑油）INDEX HEAD UNLOCKED （分度头未锁紧）MT NOT READY （机床没准备好）MG OVERLOAD （刀库过载）LUB EMPTY （润滑无油）AIR PRESSURE （气压不足）COOLANT NOT READY （冷却没准备好）LUBE EMPTY （油雾油位低，润滑油位低）LUB PRESSURE LOW （润滑压力低）CONVEY VERLOAD （排屑过载）LUB OVERLOAD （润滑过载）LUBE PRESSURE LOW （油雾压力低）SERIAL SPINDLE ALARM (串行主轴报警) NC BATTERY LOW ALARM (NC电池低报警) MAGAZINE MOVE LIMIT SWITCH ERROR SPINDLE TOOL UNLAMP POSITION LIMIT SWIT CH ERRORMAGAZINE NOT IN POSITION OR SENSOR ERR ORAIR PRESSURE LOW ALARM (气压低报警) MOTOR OVERLOAD (电机过载)T CODE > MAGAZINE TOOLST CODE < 1 ERROR5TH AXIS HARDWARE OVERTRAVER LIMIT ERR ORDOOR IS OPENED (开门)LUB PRESSURE SWITCH ERROR (油压开关错误) SPINDLE OIL COOLANT UNIT ERROR SPINDLE LOAD ABNORMAL （主轴负荷异常）TRANSDUCER ALARM （传感器报警）BED-HEAD LUBRICATE OFF （床头润滑关闭）EMG OFFHYDRAULIC CHUCK PRESS LOW 液压夹头压力低HYDRAULIC TAIL PRESS LOW 液压尾座压力低LUB 0IL LOW （油压低）TURRET CODE ERROR （转塔码错误）TURRET RUN OVERTIME （转塔运行超时）MANUAL HANDLE INTERRUPTTRY TO RUN SPINDLE WHILE CHUCK NOT LOC K TRY TO RUN SPINDLE WHILE TAIL NOT LOCK SPINDLE NEUTRAL GEARMAGAZINE ADJUSTHYDRAULIC NOT RUNSAFETY DOOR BE OPENEDSAFETY DOOR NOT CLOSENOT ALL AXIS HAVE GONE BACK REFIN ADJUST,IGNORE GOING BACK REF AFTER EXCHANGE TOOL,CYCLE STARTATC MOTOR QF16 OFFX AXIS IS LOCKED （X 轴被锁定）Y AXIS IS LOCKED （Y 轴被锁定）Z AXIS IS LOCKED （Z 轴被锁定）A AXIS IS LOCKED （A 轴被锁定）SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭)SPINDLE ORIENTATION INCOMPLETE（主轴定位不完全）M FUNCTION NOT COMPLETE（M 功能无法完成）SPINDLE NOT IN GEAR POSITION（齿轮不在主轴位置）SPINDLE NOT CHANGED TO LOW GEAR（主轴没有变为低档）SPINDLE NOT CHANGED TO HIGH GRAR（主轴没有变为高档）MAG NOT BACKWARDSPINDLE TOOL NOT CLAMPSPINDLE TOOL NOT UNCLAMPMAG NOT IN POSITIONMAG DOES NOT ROTATEMAG DOES NOT STOP RUNNINGA AXIS HAVE NOT CLAMPEDA AXIS HAVE NOT UNCLAMPEDSET D499=1,"MAG.JOG" SWITCH ON HYDRAULIC MOTOR QF7 OFF（液压马达QF7关闭）HYDRAULIC TEMPRETURE HIGH（液压使用温度高）HYDRAULIC FILTER BLOCKED液压过滤器阻止HYDRAULIC OIL LEVEL LOW 液压油位低HYDRAULIC FAN QF8 OFF液压风扇QF8关闭HELIX CONYER QF9 OR QF10 OFFCHAIN CONYER QF11 OFFCOOLANT MOTOR QF12 OFF （冷却液电机QF12关闭）COOLNT LEVEL LOW,CYCLE STOP AFTER 20 M INUTESINNER COOLANT BLOCK （内冷却堵塞）SPINDLE COOLANT MOTOR QF14 OFF （主轴冷却液电机QF14关闭）INNER COOLANT QF13 OFF 内冷却液QF13关闭MAG MOTOR QF15 OFFCABINET COOLANT EQUIP QF20 OFFOIL GATHER QF24 OFFAIR PRESSURE LOW （低气压）SPINDLE COOLANT MOTOR FAULT（主轴冷却液电机故障）LUB.OIL IS LOW （润滑油低）DOOR OPEN （门打开）FRONT DOOR(R) OPEN （前门打开）LEFT DOOR OPEN （左门打开）LUBRICATION OIL QF23 OFF 润滑油QF23关闭LUBRICATION PRESS LOW （润滑油位低）IN ADJUST,MAG CAN'T EXCHANGE T（在调整，刀库不能交换T）NOT ALL DOOR CLOSED （门没有全部关闭）IN M06,MAG NOT READY 在M06，刀库未准备好MAGAZINE NOT READY （刀库未准备好）POCKET NOT HORIZANTALIN M06,Z NOT BACK TO 2ND REFIN M06,Z AXIS NOT IN PSW1ATC NOT IN ZERO POSITIONSPINDLE ORIENTATION UNCOMPLETE POCKET NOT HOR./MAG NOT BCKWRD POCKET NOT VER./MAG NOT FORWRD UNCLAMP TOOL HAS NOT COMPLETED CLAMP TOOL HAS NOT COMPLETEDAIM TOOL NO. IS WRONGMAG NOT BACKWARDAFTER RETRACT,SET R.T.BACK OFFZ NOT IN PSW2,FORBID ATC RUNNINGD499 EQUAL 1MAG.JOG SOFT SWITCH IS ON Z NOT IN PSW2,FORBID MAG FORWARD CHEKE SPINDLE MODULE ALARMOIL WATER SEPARATOR QF24 OFFSET THE SOFT SWITCH MAG.JOG OFFSET D499 TO 0 设定D499为0K PARAM ABOUT MAG SET IS WRONG关于MAG的K参数设定错误MECHANICAL BRAKE NOT RELEASED机床抱闸没有松开MECHANICAL BRAKE IS WRONG机床抱闸错误PLEASE ADD LUB.OIL 请加润滑油PROBE BATTERY VOLTAGE IS LOW探头电池电压低PROBE IS ERR 探头错误PARAMETER WRITE ENABLE 参数写使能PMC EDIT ENABLE （PMC编辑使能）CHECK LUB ROUTINSPINDLE GEAR SIGNAL MISS主轴档位信号消失T_CLAMPED_SIGNAL MISS T夹紧信号消失SP OVERRIDE SWITCH DISCONNECTION主轴倍率开关断路FEED OVERRIDE SWITCH DISCONNECTION 进给倍率开关断路THE TOTAL NUMBER OF POCKETS SET ERR CHANGE T STOPED BECAUSE NO AIR因为缺少压空交换停止THE COOLANT WATER TOO LOW,ADD COOL ANT WATER AT ONCE 冷却水少立即加水COOLANT LEVEL LOW,ADD COOLANT WATE R 冷却水液位低PLEASE REPLACE CNC BATTERY QUICKLY 请立即更换CNC电池。
机床专业术语相关英语词汇
机床行业英汉对照3-Jaws indexing spacers 三爪、分割工具头A.T.C.system 加工中心机刀库Aluminum continuous melting holding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器951Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机Engraving machines,laser 激光雕刻机Etching machines 蚀刻机Finishing machines 修整机Fixture 夹具Forging dies 锻模Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备Gear cutting machines 齿轮切削机Gears 齿轮Gravity casting machines 重力铸造机Grinder bench 磨床工作台Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮952Hand tools 手工具Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床Lathes,high-speed 高速车床Lathes,turret 六角车床Lathes,vertical 立式车床Lubricants 润滑液Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心Machining centers,horizontal 卧式加工中心Machining centers,horizontal & vertical 卧式及立式加工中心Machining centers,vertical 立式加工中心Machining centers,vertical double-column type 立式双柱加工中心Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头Milling machines 铣床Milling machines,bed type 床身式铣床Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床Milling machines,vertical & horizontal 立式及卧式铣床Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯Mold heaters/chillers 模具加热器/冷却器Mold polishing/texturing 模具打磨/磨纹953Mold repair 模具维修Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机P type PVC waterproof rolled sheet making plant P型PVC高分子防水PCB fine piecing systems 印刷电器板油压冲孔脱料系统Pipe & tube making machines 管筒制造机Planing machines 刨床Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具Powder metallurgic forming machines 粉末冶金成型机Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床Presses,transfer 自动压力机Pressing dies 压模Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机954Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手离心压力机Presses,eccentric六角立式铣床Milling machines,turret vertical六角车床Lathes,turret螺栓,螺帽及螺丝Bolts,screws & nuts螺纹磨床Grinders,thread冷却机Coolers冷锻Forging,cold冷锻冲压机Presses,cold forging立式双柱加工中心Machining centers,vertical double-column type立式铣床Milling machines,vertical立式油压拉床Vertical hydraulic broaching machine立式刨床Planing machines vertical立式车床Lathes,vertical立式带锯Saws,vertical band立式加工中心Machining centers,vertical立式及卧式铣床Milling machines,vertical & horizontal立式钻床Drilling machines,vertical联轴器Coupling连续溶解保温炉Aluminum continuous melting & holding furnaces连续冲模Dies-progressive链传动Chain drive切断机Cutting-off machinesCNC刀杆CNC toolings曲柄压力机presses,crank修整机Finishing machines舍弃式刀头Disposable toolholder bits润滑系统Lubrication Systems润滑液Lubricants熔热处理炉Heating treatment funaces三爪、分割工具头3-Jaws indexing spacers伺服冲床Presses,servo输送链Conveying chains手工具Hand tools砂轮修整器Wheel dressers955蚀刻机Etching machines外圆磨床Grinding machines,cylindrical搪磨机Honing machines搪孔头Boring heads卧式铣床Milling machines,horizontal卧式带锯Saws,horizontal band卧式加工中心Machining centers,horizontal卧式及立式加工中心Machining centers,horizontal & vertical万能铣床Milling machines,universal万能磨床Grinding machines,universal镗床Boring machines弯曲机Bending machines弯管机Tube bending machines通用加工中心Machining centers,general铜锻Forging,copper铣头Milling heads铣床Milling machines无心磨床Grinding machines,centerless无心精研机Lapping machines,centerless压模Pressing dies压铸冲模Die casting dies压铸机Die casting machines油冷却器Oil coolers造链机Chain making tools造线机Cable making tools造钉机Nail making machines印刷电器板油压冲孔脱料系统PCB fine piecing systems摇臂钻床Drilling machines,radial硬(软)板(片)材及自由发泡板机组Hard/soft and free expansion sheet making plant辗压机Rolling machines液压元件Hydraulic components液压冲床Presses,hydraulic液压动力元件Hydraulic power units液压工具Hydraulic power tools液压回转缸Hydraulic rotary cylindersP型PVC高分子防水P type PVC waterproof rolled sheet making plant刨床Planing machines牛头刨床Shapers其他铸造Casting,other其他锻造Forging,other模芯Mold core模具Molds模具维修Mold repair模具打磨/磨纹Mold polishing/texturing956模具单元Mold & die components模具加热器/冷却器Mold heaters/chillers磨轮Grinding wheels磨削工具Grinding tools磨床Grinding machines磨床工作台Grinder bench平衡设备Balancing equipment气油压虎钳Pneumatic hydraulic clamps气动冲床Presses,pneumatic气动工具Pneumatic power tools轴shafts轴承Bearings轴承配件Bearing fittings轴承加工机Bearing processing equipment肘杆式压力机Presses,knuckle joint铸铝Casting,aluminium铸铜Casting,copper铸造设备Foundry equipment铸钢Casting,steel铸灰口铁Casting,gray iron织麦激光切割机Woven-Cutting machines重力铸造机Gravity casting machines重型车床Lathes,heavy-duty主轴spindles扳手Wrenches 拔丝机Drawing machines保温炉Heat preserving furnaces插床Slotting machines齿轮Gears齿轮切削机Gear cutting machines冲压机Stamping parts冲子研磨器Punch formers超声波打磨机Grinders,ultrasonic车床工作台Lathe bench磁性工具Magnetic tools传动链Transmitted chains床身式铣床Milling machines,bed type带传动Belt drive带锯Saws,band带锯床Sawing machines,band电脑数控镗床CNC boring machines电脑数控弯折机CNC bending presses电脑数控铣床CNC milling machines电脑数控线切削机CNC wire-cutting machines电脑数控磨床CNC grinding machines957电脑数控车床CNC lathes电脑数控电火花线切削机CNC EDM wire-cutting machines电脑数控电火花机CNC electric discharge machines电脑数控雕刻机CNC engraving machines电脑数控机床配件CNC machine tool fittings电脑数控剪切机CNC shearing machines电脑数控钻床CNC drilling machines电动刀具Electric power tools电火花机Electric discharge machines(EDM)雕刻机Engraving machines刀片Blades刀具Cutters倒角机Chamfer machines多轴钻床Drilling machines,multi-spindle锻铝Forging,aluminium锻压机Presses,forging锻模Forging dies仿形铣床Milling machines,duplicating粉末冶金成型机Powder metallurgic forming machines反射炉Reverberatory furnaces钢锻Forging,steel高速车床Lathes,high-speed高速钻床Drilling machines,high-speed管筒制造机Pipe & tube making machines滚筒Rollers工具磨床Grinders,tools & cutters攻螺丝机Tapping machines弓锯Saws,hack虎钳Vises换模系统Mold changing systems夹盘Chucks夹具Fixture夹具/支持系统Clamping/holding systems剪切机Shearing machines加工中心机刀库A.T.C.system激光切割Laser cutting激光雕刻机Engraving machines,laser激光钢板切割机Laser cutting for SMT stensil集合管Manifolds矫直机Straightening machines金属板成型机Sheet metal forming machines金属板加工机Sheet metal working machines锯片Blades,saw锯床Sawing machines958卷边工具Crimping tools晶圆切割机Dicing saws精密平口钳Vises,tool-maker精研机Lapping machines可锻铸铁Casting,malleable iron快速换模系统Quick mold change systems卡口Bayonet开关及按钮Switches & buttons钻石刀具Diamond cutters钻头drills钻模Jigs钻床Drilling machines钻床工作台Drilling machines bench自动压力机Presses,transfer959。
数控机床英语词汇介绍
数控机床英语词汇介绍数控机床机械零件mechanical parts 游标卡尺slide caliper千分尺micrometer calipers 攻丝tap 步进电机stepper motor 镗床boring machine钻床drill machine铣床milling machine伺服电机actuating motor塑性变形plastic distortion工业造型设计industrial moulding 脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer技术要求technical requirements装配图assembly drawing尺寸标注size marking零件图part drawing标准件standard component剖视图profile chart视图view投影projection机械制图Mechanical drawing 电火花加工electric spark machiningdesign电动机electromotor集成电路integrate circuit 液压hydraulic pressure加工machining铸造found装配assembling拉孔broaching拉床broaching machine 焊weld压模stamping锻forge磨床grinder车削turning钻削镗削bore电火花线切割加工electrical discharge车床lathe wire- cutting 车刀lathe tool加工中心machining center齿轮gear齿轮加工gear machining工件work-piece铣刀milling cutter铣削mill螺钉screw螺纹加工thread processing半导体元件semiconductor element正火normalizing退火anneal热处理heat treatment硬度rigidity应力stress变形deformation变形力deforming force精度precision机械加工余量machining allowance 金属切削metal cutting机床machine toolWater jet looms 喷水织机Machinery织造准备机、织造机、簇绒机Weaving Preparatory and Auxiliary Machinery织造准备及辅助机Weaving Auxiliary Machinery and Additional Devices 织造辅助机械及附加装置Washing,Bleaching,Dyeing,Printing, Finishing and Make-up Machinery洗涤、漂白、染色、印花、整理及包装机械Washing,Bleaching and Wet Treatment 洗涤、漂白及湿式处理机Warping machines整经机Warp stop motions 断经自停装置Top printing machines套色印花机Thermo-fixing machines 热定形机Tentering and stentering machines拉幅机Tensionless dryers 无张力干燥机Weaving Preparatory Machinery,Spinning Machinery 纺纱机Weaving Machinery, Tufting Spinning Machinery and TwistingMachines for Natural and Man Made Sewing needles 缝纫机针Fibres,Wadding,Felting and Hat-Making Machines, Non Woven Fabric Sewing machines缝纫机Machinery,Cordage and Rope-Making Rotor spinning frames 气流纺纱机Machinery天然纤维和化学纤维用纺纱机及加捻机械，填絮，缩绒，制帽机，无纺织物机械，搓绳制绳机。
机械专业英语词汇【完整版】
v1.0 可编辑可修改1机械专业英语词汇金属切削 metal cutting 渗碳 carburization 机床 machine tool 电路 circuit金属工艺学 technology of metals 半导体元件 semiconductor element 刀具 cutter 反馈 feedback摩擦 friction 发生器 generator联结 link 直流电源 DC electrical source 传动 drive/transmission 门电路 gate circuit 轴 shaft 逻辑代数 logic algebra 弹性 elasticity 外圆磨削 external grinding频率特性 frequency characteristic 内圆磨削 internal grinding 误差 error 平面磨削 plane grinding响应 response 变速箱 gearbox定位 allocation 离合器 clutch机床夹具 jig 绞孔 fraising动力学 dynamic 绞刀 reamer运动学 kinematic 螺纹加工 thread processing静力学 static 螺钉 screw 分析力学 analyse mechanics 铣削 mill拉伸 pulling 铣刀 milling cutter压缩 hitting 功率 power剪切 shear 工件 workpiece扭转 twist 齿轮加工 gear mechining 弯曲应力 bending stress 齿轮 gear强度 intensity 主运动 main movement三相交流电 three-phase AC 主运动方向 direction of main movement 磁路 magnetic circles 进给方向 direction of feed变压器 transformer 进给运动 feed movement异步电动机 asynchronous motor 合成进给运动 resultant movement of feed 几何形状 geometrical 合成切削运动 resultant movement of精度 precision cutting正弦形的 sinusoid 合成切削运动方向 direction of resultant交流电路 AC circuit movement of cutting机械加工余量 machining allowance 切削深度 cutting depth变形力 deforming force 前刀面 rake face变形 deformation 刀尖 nose of tool应力 stress 前角 rake angle硬度 rigidity 后角 clearance angle热处理 heat treatment 龙门刨削 planing退火 anneal 主轴 spindle正火 normalizing 主轴箱 headstock脱碳 decarburization 卡盘 chuck12v1.0 可编辑可修改3加工中心 machining center 皮带 strap车刀 lathe tool 精加工 finish machining车床 lathe 粗加工 rough machining 钻削镗削 bore 变速箱体 gearbox casing车削 turning 腐蚀 rust磨床 grinder 氧化 oxidation基准 benchmark 磨损 wear钳工 locksmith 耐用度 durability锻 forge 随机信号 random signal 压模 stamping 离散信号 discrete signal 焊 weld 超声传感器 ultrasonic sensor 拉床 broaching machine 集成电路 integrate circuit 拉孔 broaching 挡板 orifice plate装配 assembling 残余应力 residual stress 铸造 found 套筒 sleeve 流体动力学 fluid dynamics 扭力 torsion流体力学 fluid mechanics 冷加工 cold machining 加工 machining 电动机 electromotor 液压 hydraulic pressure 汽缸 cylinder 切线 tangent 过盈配合 interference fit 机电一体化 mechanotronics 热加工 hotworkmechanical-electrical integration 摄像头 CCD camera气压 air pressure pneumatic pressure 倒角 rounding chamfer 稳定性 stability 优化设计 optimal design介质 medium 工业造型设计 industrial moulding design 液压驱动泵 fluid clutch 有限元 finite element阀门 valve 插齿 gear shaping失效 invalidation 伺服电机 actuating motor强度 intensity 铣床 milling machine载荷 load 钻床 drill machine应力 stress 镗床 boring machine安全系数 safty factor 步进电机 stepper motor可靠性 reliability 丝杠 screw rod螺纹 thread 导轨 lead rail螺旋 helix 组件 subassembly键 spline 可编程序逻辑控制器 Programmable销 pin Logic Controller PLC滚动轴承 rolling bearing 电火花加工 electric spark machining滑动轴承 sliding bearing 电火花线切割加工 electrical discharge弹簧 spring wire - cutting制动器 arrester brake 相图 phase diagram十字结联轴节 crosshead 热处理 heat treatment联轴器 coupling 固态相变 solid state phase changes链 chain 有色金属 nonferrous metal24v1.0 可编辑可修改5陶瓷 ceramics 范成法 generation method 合成纤维 synthetic fibre 定义域 definitional domain电化学腐蚀 electrochemical corrosion 值域 range 车架 automotive chassis 导数\\微分 differential coefficient 悬架 suspension 求导 derivation转向器 redirector 定积分 definite integral变速器 speed changer 不定积分 indefinite integral 板料冲压 sheet metal parts 曲率 curvature孔加工 spot facing machining 偏微分 partial differential 车间 workshop 毛坯 rough工程技术人员 engineer 游标卡尺 slide caliper气动夹紧 pneuma lock 千分尺 micrometer calipers 数学模型 mathematical model 攻丝 tap画法几何 descriptive geometry 二阶行列式 second order determinant 机械制图 Mechanical drawing 逆矩阵 inverse matrix 投影 projection 线性方程组 linear equations 视图 view 概率 probability剖视图 profile chart 随机变量 random variable 标准件 standard component 排列组合 permutation and combination 零件图 part drawing 气体状态方程 equation of state of gas 装配图 assembly drawing 动能 kinetic energy尺寸标注 size marking 势能 potential energy 技术要求 technical requirements 机械能守恒 conservation of mechanical 刚度 rigidity energy内力 internal force 动量 momentum位移 displacement 桁架 truss疲劳极限 fatigue limit 余子式 cofactor断裂 fracture 逻辑电路 logic circuit塑性变形 plastic distortion 触发器 flip-flop脆性材料 brittleness material 脉冲波形 pulse shape刚度准则 rigidity criterion 数模 digital analogy垫圈 washer 液压传动机构 fluid drive mechanism垫片 spacer 机械零件 mechanical parts 直齿圆柱齿轮 straight toothed spur gear 淬火冷却 quench 斜齿圆柱齿轮 helical-spur gear 淬火 hardening直齿锥齿轮 straight bevel gear 回火 tempering运动简图 kinematic sketch 调质 hardening and tempering齿轮齿条 pinion and rack 磨粒 abrasive grain 蜗杆蜗轮 worm and worm gear 结合剂 bonding agent虚约束 passive constraint 砂轮 grinding wheel曲柄 crank 机械零件 mechanical parts摇杆 racker 淬火冷却 quench凸轮 cams 淬火 hardening共轭曲线 conjugate curve 回火 tempering36v1.0 可编辑可修改7调质 hardening and tempering CNC grinding machines 电脑数控磨床磨粒 abrasive grain CNC lathes 电脑数控车床结合剂 bonding agent CNC machine tool fittings 电脑数控机床配砂轮 grinding wheel件CNC milling machines 电脑数控铣床 CNC机床行业部分英汉对照（1)：按英文字母排序3-Jaws indexing spacers 三爪、分割工具头加工中心机刀库Aluminum continuous melting & holding furnaces 连续溶解保温炉Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片Bolts,screws & nuts 螺栓,螺帽及螺丝Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁shearing machines 电脑数控剪切机CNC toolings CNC 刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Drilling machines 钻床Drilling machines bench 钻床工作台Drillingmachines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Casting,malleable iron 可锻铸铁Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床 CNCdrilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机4 8v1.0 可编辑可修改9 Gears 齿轮Manifolds 集合管Gravity casting machines 重力铸造机 Grinde Milling heads 铣头r bench 磨床工作台Milling machines 铣床Grinders,thread 螺纹磨床Milling machines,bed type 床身式铣床Grinders,tools & cutters 工具磨床Milling machines,duplicating 仿形铣床Grinders,ultrasonic 超声波打磨机Milling machines,horizontal 卧式铣床 Millin Grinding machines 磨床g machines,turret vertical 六角立式铣床Grinding machines,centerless 无心磨床Milling machines,universal 万能铣床Grinding machines,cylindrical 外圆磨床Milling machines,vertical 立式铣床Grinding machines,universal 万能磨床Milling machines,vertical & horizontal 立式Grinding tools 磨削工具及卧式铣床Grinding wheels 磨轮Mold & die components 模具单元Hand tools 手工具Mold changing systems 换模系统Hard/soft and free expansion sheet making Mold core 模芯plant 硬(软)板(片)材及自由发泡板机组Mold heaters/chillers 模具加热器/冷却器Heat preserving furnaces 保温炉Mold polishing/texturing 模具打磨/磨纹Heating treatment funaces 熔热处理炉Mold repair 模具维修Honing machines 搪磨机Molds 模具Hydraulic components 液压元件Nail making machines 造钉机Hydraulic power tools 液压工具Oil coolers 油冷却器Hydraulic power units 液压动力元件 Hydra Overflow cutting machines for aluminium wulic rotary cylinders 液压回转缸heels 铝轮冒口切断机Jigs 钻模P type PVC waterproof rolled sheet making Lapping machines 精研机 plant P 型 PVC 高分子防水Lapping machines,centerless 无心精研机PCB fine piecing systems 印刷电器板油压Laser cutting 激光切割冲孔脱料系统割机Planing machines 刨床Lathe bench 车床工作台Planing machines vertical 立式刨床Lathes,automatic 自动车床Pneumatic hydraulic clamps 气油压虎钳Lathes,heavy-duty 重型车床Pneumatic power tools 气动工具Lathes,high-speed 高速车床Powder metallurgic forming machines 粉末Lathes,turret 六角车床冶金成型机Lathes,vertical 立式车床Presses,cold forging 冷锻冲压机Lubricants 润滑液presses,crank 曲柄压力机Lubrication Systems 润滑系统Presses,eccentric 离心压力机Lubricators 注油机Presses,forging 锻压机Machining centers,general 通用加工中心Presses,hydraulic 液压冲床Machining centers,horizontal 卧式加工中心Presses,knuckle joint 肘杆式压力机Machining centers,horizontal & vertical 卧Presses,pneumatic 气动冲床式及立式加工中心Presses,servo 伺服冲床Machining centers,vertical 立式加工中心Presses,transfer 自动压力机Machining centers,vertical double-column ty Pressing dies 压模pe 立式双柱加工中心Punch formers 冲子研磨器Magnetic tools 磁性工具Quick die change systems 速换模系统510v1.0 可编辑可修改11 Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机Transmitted chains 传动链Tube bending machines 弯管机Vertical hydraulic broaching machine 立式油压拉床Vises 虎钳Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手螺丝词汇的中英文对照六角盖头螺帽 HEX CAP NUTS六角锯齿螺帽 HEX SERRATED NUTS六角轮缘螺帽 HEX FLANGE NUTS 高脚螺帽 HEX COUPLING NUTS(HIGH NUTS)圆螺帽 ROUND NUTS四角螺帽 SQUARE NUTS6 12v1.0 可编辑可修改13 HEAVY HEX NUTS不锈钢六角螺帽 STAINLESS STEEL HEXNUTS不锈钢尼龙嵌入螺帽 STAINLESS STEELNYLON INSERT LOCK NUTS普通六角螺帽 HEX NUTS六角重型螺帽 HEAVY HEX NUTS薄型螺帽 HEX JAM NUTS尼龙嵌入防松螺帽 NYLON INSERT LOCK NUTS机械螺丝用六角螺帽 HEX MACHINE SCREW NUT机械工具英语机械工具 spanner 扳子 (美作:wrench) double-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子 (美作:socket wrench) calipers 卡规pincers, tongs 夹钳 shears 剪子 hacksaw 钢锯wire cutters 剪线钳 multipurpose pliers,universal pliers 万能手钳adjustable pliers 可调手钳 punch 冲子drill 钻 chuck 卡盘Assembly line 组装线Layout 布置图scraper 三角刮刀 reamer 扩孔钻 calliper Conveyer 流水线物料板外贸常用机械英语大全gauge 孔径规Rivet table 拉钉机Rivet gun 拉钉枪rivet 铆钉 nut 螺母 locknut 自锁螺母,Screw driver 起子防松螺母 bolt 螺栓Pneumatic screw driver 气动起子worktable 工作桌pin, peg, dowel 销钉 washer 垫圈 stapl OOBA 开箱检查e U 形钉fit together 组装在一起fasten 锁紧(螺丝)oil can 油壶 jack 工作服 grease gun 注fixture 夹具(治具)油枪pallet 栈板barcode 条码机械加工抛光 polishing 安装 to assem barcode scanner 条码扫描器ble 衬套 bushing fuse together 熔合fuse machine 热熔机714v1.0 可编辑可修改15 repair 修理electrical sparkle 电火花operator 作业员welder 电焊机QC 品管staker=reviting machine 铆合机supervisor 课长position 职务ME 制造工程师president 董事长MT 制造生技general manager 总经理cosmetic inspect 外观检查special assistant manager 特助inner parts inspect 内部检查factory director 厂长thumb screw 大头螺丝department director 部长lbs. inch 镑、英寸deputy manager | =vice manager 副理 sectio EMI gasket 导电条n supervisor 课长front plate 前板deputy section supervisor =vice section supe rear plate 后板risor 副课长chassis 基座group leader/supervisor 组长bezel panel 面板line supervisor 线长power button 电源按键assistant manager 助理reset button 重置键to move, to carry, to handle 搬运Hi-pot test of SPS 高源高压测试be put in storage 入库Voltage switch of SPS 电源电压接拉键pack packing 包装sheet metal parts 冲件to apply oil 擦油plastic parts 塑胶件to file burr 锉毛刺SOP 制造作业程序final inspection 终检material check list 物料检查表to connect material 接料work cell 工作间to reverse material 翻料trolley 台车wet station 沾湿台carton 纸箱Tiana 天那水left fork 叉车to load material 上料personnel resource department 人力资源部to unload material 卸料production department 生产部门to return material/stock to 退料planning department 企划部scraped |\\'skrpid|报废QC Section 品管科scrape ..v.刮;削stamping factory 冲压厂deficient purchase 来料不良painting factory 烤漆厂manufacture procedure 制程molding factory 成型厂deficient manufacturing procedure 制程不良common equipment 常用设备oxidation |\\' ksi\\'dein|氧化uncoiler and straightener 整平机scratch 刮伤punching machine 冲床dents 压痕robot 机械手defective upsiding down 抽芽不良hydraulic machine 油压机defective to staking 铆合不良lathe 车床embedded lump 镶块planer |plein|刨床feeding is not in place 送料不到位miller 铣床stamping-missing 漏冲grinder 磨床production capacity 生产力linear cutting 线切割education and training 教育与训练816v1.0 可编辑可修改17 proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车外贸常用机械英语大全(续)compound die 合模quality 品质die locker 锁模器prepared by 制表pressure plate=plate pinch 压板notes 说明bolt 螺栓year-end physical inventory difference analysis administration/general affairs dept 总务部sheet 年终盘点差异分析表automatic screwdriver 电动启子physical inventory 盘点数量thickness gauge 厚薄规physical count quantity 帐面数量gauge(or jig)治具difference quantity 差异量power wire 电源线cause analysis 原因分析buzzle 蜂鸣器raw materials 原料defective product label 不良标签materials 物料identifying sheet list 标示单finished product 成品location 地点semi-finished product 半成品present members 出席人员packing materials 包材subject 主题good product/accepted goods/ acceptedconclusion 结论parts/good parts 良品decision items 决议事项defective product/non-good parts 不良品responsible department 负责单位disposed goods 处理品pre-fixed finishing date 预定完成日warehouse/hub 仓库approved by / checked by / prepared by 核准/on way location 在途仓审核/承办oversea location 海外仓PCE assembly production schedule sheet PCE spare parts physical inventory list 备品盘点清type 形态item/group/class 类别model 机锺spare molds location 模具备品仓work order 工令skid/pallet 栈板revision 版次tox machine 自铆机remark 备注wire EDM 线割production control confirmation 生产确认EDM 放电机checked by 初审coil stock 卷料approved by 核准sheet stock 片料department 部门tolerance 工差stock age analysis sheet 库存货龄分析表score=groove 压线on-hand inventory 现有库存cam block 滑块available material 良品可使用pilot 导正筒obsolete material 良品已呆滞trim 剪外边to be inspected or reworked 待验或重工pierce 剪内边total 合计drag form 压锻差cause description 原因说明pocket for the punch head 挂钩槽part number/ P/N 料号slug hole 废料孔918v1.0 可编辑可修改19feature die 公母模part number/P/N 料号expansion dwg 展开图good products 良品radius 半径scraped products 报放心品shim(wedge)楔子defective products 不良品torch-flame cut 火焰切割finished products 成品set screw 止付螺丝disposed products 处理品form block 折刀barcode 条码stop pin 定位销flow chart 流程表单round pierce punch=die button 圆冲子assembly 组装shape punch=die insert 异形子stamping 冲压stock locater block 定位块molding 成型under cut=scrap chopper 清角spare parts=buffer 备品active plate 活动板coordinate 座标baffle plate 挡块dismantle the die 折模cover plate 盖板auxiliary fuction 辅助功能male die 公模poly-line 多义线female die 母模heater band 加热片groove punch 压线冲子thermocouple 热电偶air-cushion eject-rod 气垫顶杆sand blasting 喷沙spring-box eject-plate 弹簧箱顶板grit 砂砾bushing block 衬套derusting machine 除锈机insert 入块degate 打浇口club car 高尔夫球车dryer 烘干机capability 能力induction 感应parameter 参数induction light 感应光factor 系数response=reaction=interaction 感应viscosity 涂料粘度edge finder 巡边器alkalidipping 脱脂concave 凸main manifold 主集流脉convex 凹bezel 斜视规short 射料不足blanking 穿落模nick 缺口dejecting 顶固模speck 瑕demagnetization 去磁;消磁shine 亮班high-speed transmission 高速传递splay 银纹heat dissipation 热传 rack 上料gas mark 焦痕degrease 脱脂delamination 起鳞rinse 水洗cold slug 冷块alkaline etch 龄咬blush 导色desmut 剥黑膜gouge 沟槽;凿槽. rinse 纯水次satin texture 段面咬花Chromate 铬酸处理witness line 证示线Anodize 阳性处理patent 专利seal 封孔grit 沙砾revision 版次granule=peuet=grain 细粒1020v1.0 可编辑可修改21grit maker 抽粒机CTN Carton 卡通箱cushion 缓冲PAL Pallet/skid 栈板magnalium 镁铝合金PO Purchasing Order 采购订单magnesium 镁金MO Manufacture Order 生产单metal plate 钣金D/C Date Code 生产日期码lathe 车ID/C Identification Code (供应商)识别码mill 锉SWR Special Work Request 特殊工作需求plane 刨L/N Lot Number 批号grind 磨P/N Part Number 料号drill 铝boring 镗blinster 气泡fillet 镶;嵌边through-hole form 通孔形式voller pin formality 滚针形式cam driver 铡楔shank 摸柄crank shaft 曲柄轴augular offset 角度偏差velocity 速度production tempo 生产进度现状torque 扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火carbonization 碳化tungsten high speed steel 钨高速的阀门种类英汉术语对照Air valves 空气阀门Angle Stop valves 角式截止阀Angle Throttle Valves 角式节流阀Angle Type Globe Valves 门角式截止阀Ash valves 排灰阀Aspirating valves 吸（抽）气阀Auxiliary valves 辅助（副）阀Balance valves 平衡阀Bellows valves 波纹管阀Blowdown valves 泄料（放空，排污）阀Brake valves 制动阀Butterfly Type Non-slam Check 蝶式缓冲止回阀Butterfly Valves with Gear Actuator 蜗轮传动蝶阀Buttwelding valves 对焊连接阀organic solvent 有机溶剂bracket 小磁导liaison 联络单volatile 挥发性resistance 电阻ion 离子titrator 滴定仪beacon 警示灯coolant 冷却液crusher 破碎机Double Disc Flat Gate Valves 双闸板平机械类常用英语：生产类行式双闸板闸板PCS Pieces 个(根,块等)PRS Pairs 双(对等)1122v1.0 可编辑可修改23 Drainage valves 排水阀 Plunger valves 柱塞阀Electric Actuated Stop Valves 电动截止 Pressure valve 压力（増压）阀阀 Piping Pumps 管道泵Electric Actuated Wedge Gate Valves 电 Piping Safety Valves 管道安全阀动楔式闸阀 Plunger Globe Valves 柱塞截止阀Electric Double Disk Parallel Gate Valve Quick Draining Valves 快速排污阀s 电动平行式双闸板闸板 Restrictor Valves 过流阀(或节流阀)Emergeny Cut-off Valves 紧急切断阀 Safety Valves 安全阀Exhaust valves 排气阀 Screw Pumps 螺杆泵Free Float Type Steam Trap 浮球式疏水 Scum Gate Valves 排渣闸阀阀S olenoid valves 电磁阀Flange Ball Valves 法兰球阀 Single Disc Flat Gate Valves 单闸板平板 Flange Gate Valves 法兰闸阀闸阀Flange Globe Valves 法兰截止阀 Single Opening Exhaust Valves 单口排气 Gauge Valves 仪表阀球Hand-operated valves 手动阀 Slurry Pumps 泥浆泵Hard Seal Butterfly Valves 金属密封碟 Stop Valves 截止阀阀 Strainer 过滤器High Temperature Pressure Power Statio Submerged Motor Pumps 潜水电泵(排污n Gate Valves 高温高压电站闸阀泵)High Temperature Pressure Power Statio Swing Check Valves 旋启式止回阀n Globe Valves 高温高压电站截止阀 Swing Check Valves 旋启式止回阀Hydraulic relay valves 液压继动阀 Tank Lorry Ball Valves 槽车球阀Lift Check Valves 升降式止回阀 T-Cock 三通Lift Check Valves 升降式止回阀 Thin Gate Valves 薄型闸阀Limit valves 限位阀 Throttle Valves 节流阀Lining Butterfly Valves 衬里碟阀缓闭止回阀Lining Check Valves 衬里止回阀 Triple (tee) valves 三通阀Lining Cock 衬里二通 Two-way valves 二通阀Lining Globe Valves 衬里截止阀 Under Water Pumps 液下泵Lining T-Cock Valves 衬里三通旋塞阀 Vacuum Pumps 水力喷射器(真空泵)Liquid Indicator 液位计 Vertical Lift Check Valves 立式止回阀 LPG Pipe Fitting 液化气管件 Wafer Check Valves 对夹式止回阀Magnetic Co-operate Globe Valves 磁耦 Wafer plate valves 对夹蝶板阀合截止阀 Wafer Type Butterfly Valves with RubberMagnetism Forle Pumps 磁力泵Itning 对夹式衬胶蝶阀Manual Oil Pumps Valves 手摇油泵(阀) Waste Valves 排污箱(阀)Water Seal Gate Valves 水封闸阀 Meter Needle Type Globe Valves 仪表 Wedge Gate Valves 楔式闸阀针形截止阀 Y Type and Cylinder Filters Y 型筒型过滤Oblique Stop Valves 直流式截止阀器Parallel Slide Valves 浆液阀阀门零部件英汉术语对照Pintle valve 针形阀 Axis Guide 轴套Piping Centrifugal Pumps 管道离心泵 Ball 球、球芯1224v1.0 可编辑可修改25Ball seat 密封圈 Piping 管路Blowdown Sealing Face 启、阀件密封面 Piston 活塞Body 阀体 Reductant 还原性介质Bonnet 阀盖 Rising stem 明杆Disc 阀瓣 Seal 阀座，密封面Mut 螺母 Seat testing pressure 压力气密封试验压Screw 螺栓力Sealing 密封件 Socket 卡套Spring 弹簧 Specifications 性能规范Stem 阀杆 Single disc 单闸板 Stem Mut 阀杆螺母 Solid 刚性Stem seal 填料 Strengh testing pressure 强度试验压力Wedge Disc 闸板 Steam , condensate 蒸汽,凝结水阀门规范技术英语术语对照 Stroke 冲程，行程 Applicable medium 适用介质 Water,oil,steam 水,温度,气Applicable temperature 适用温度 Wedge 楔式 Welding 焊接 Butt Clamp 对夹阀门材质术语英汉对照 Chemical analysis 化学成份 Atbas metal 镍铬钢Connecting format 连接形式 Buna-N rubber 丁晴橡胶 Double disc 双闸板 Casting aluminium brass 铸铝黄铜Flexible disc 弹性闸板 Casting aluminium bronze 铸铝青铜 Flange 法兰 Hoop 卡箍 Ceramic metal 陶瓷金属Inside thread 内螺纹 Chromel alloy 镍铬合金 Jacket 夹套 CHR rubber 氯晴橡胶Mains 电源 Chrominm-molybdenum-vanadium steelMaterial chemical analysis and mechanical 铬钼钒钢materials 材料 Materials for main parts Chromium-molybdenum steel 铬钼钢主要零件材料 Corrugation pad 波形垫Mechanical capacity 机械性能 Cuprum alloy 铜合金 Max. Discharging Capacity 最大排水量 Ductile Cast iron 球墨铸铁Max. Operating Temperature 最高工作温 Expanded graphite 柔性石墨度 Fine Steel Casting iron 优质碳素钢 Max. Allowable Temperature 最高允许温 Fluorous rubber 氟橡胶度 Gray Cast iron 灰铸铁 Max. Allowable Pressure 最高允许压力 Hayne's alloy 钴铬钨合金Model 型号 High tem perature steel 高温钢 Name of parts 零件名称 Monel 蒙乃尔合金nitrogen (N) 氮 Low temperature steel 低温钢 Nominal bore 公称通径 Nylon 尼龙塑料Nominal Pressure 公称压力 Polytetrafluoroethylene(PTEF) 聚四氟乙 Nozzle 排气口烯Outside thread 外螺纹 Polythene 聚乙烯Oxidant 氧化性介质 Pure aluminium 纯铝Parallel 平行 Pure cupper 纯铜1326v1.0 可编辑可修改27Rubber graphite board 橡胶石墨板Spring steel 弹簧钢Stainless acid-resisting steel 不锈耐酸钢Stainless and Graphite 不锈钢/石墨Stainless steel 不锈钢Steel Casting iron 碳素钢铸件Shell Test Pressure 壳体试验压力Service Fluid 工作介质机械类常用英语：钢材类shiver 饰纹alloy tool steel 合金工具钢 aluminium allo flow mark 流痕y 铝合金钢welding mark 溶合痕bearing alloy 轴承合金 blister steel 浸碳钢post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝bonderized steel sheet 邦德防蚀钢板 carbon striper plate 脱料板tool steel 碳素工具钢piston 活塞clad sheet 被覆板 clod work die steel 冷锻cylinder 汽缸套模用钢chip 细碎物emery 金钢砂 ferrostatic pressure 钢铁水静handle mold 手持式模具压力forging die steel 锻造模用钢 galvanized ste encapsulation molding 低压封装成型、射出成el sheet 镀锌铁板型用模具hard alloy steel 超硬合金钢 high speed too two plate 两极式（模具）l steel 高速度工具钢well type 蓄料井hot work die steel 热锻模用钢 low alloy to insulated runner 绝缘浇道方式ol steel 特殊工具钢hot runner 热浇道low manganese casting steel 低锰铸钢 marg runner plat 浇道模块塑件模具相关英文compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具ing steel 马式体高强度热处理钢valve gate 阀门浇口martrix alloy 马特里斯合金 meehanite cast band heater 环带状的电热器iron 米汉纳铸钢spindle 阀针meehanite metal 米汉纳铁 merchant iron 市spear head 刨尖头售钢材slag well 冷料井molybdenum high speed steel 钼系高速钢cold slag 冷料渣molybdenum steel 钼钢air vent 排气道nickel chromium steel 镍铬钢 prehardened welding line 熔合痕steel 顶硬钢silicon steel sheet 矽钢板 stainless steel 不eject pin 顶出针锈钢knock pin 顶出销tin plated steel sheet 镀锡铁板 tough pitch return pin 回位销反顶针copper 韧铜sleave 套筒troostite 吐粒散铁 tungsten steel 钢stripper plate 脱料板vinyl tapped steel sheet 塑胶覆面钢板insert core 放置入子runner stripper plate 浇道脱料板1428v1.0 可编辑可修改29 guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式sprue 浇口;溶渣15 30。
数控机床常用英语词汇大全
1)计算机数值控制(Computerized Numerical Control, CNC)用计算机控制加工功能，实现数值控制。
2)轴(Axis)机床的部件可以沿着其作直线移动或回转运动的基准方向。
3)机床坐标系( Machine Coordinate Systern )固定于机床上，以机床零点为基准的笛卡尔坐标系。
4)机床坐标原点( Machine Coordinate Origin )机床坐标系的原点。
5)工件坐标系( W orkpiece Coordinate Syst em )固定于工件上的笛卡尔坐标系6)工件坐标原点( Wrok-piexe Coordinate Origin)工件坐标系原点。
7)机床零点( Machine zero )由机床制造商规定的机床原点。
8)参考位置( Reference Position )机床启动用的沿着坐标轴上的一个固定点，它可以用机床坐标原点为参考基准9)绝对尺寸(Absolute Dimension)/绝对坐标值(Absolute Coordinates)距一坐标系原点的直线距离或角度。
10)增量尺寸( Incremental Dimension ) /增量坐标值(Incremental Coordinates)在一序列点的增量中，各点距前一点的距离或角度值。
11)最小输人增量(Least Input Increment)在加工程序中可以输人的最小增量单位。
12)命令增量(Least command Increment)从数值控制装置发出的命令坐标轴移动的最小增量单位。
13)插补(InterPolation)在所需的路径或轮廓线上的两个已知点间根据某一数学函数(例如：直线，圆弧或高阶函数)确定其多个中间点的位置坐标值的运算过程。
14)直线插补(Llne Interpolation)这是一种插补方式，在此方式中，两点间的插补沿着直线的点群来逼近，沿此直线控制刀具的运动。
机床机械及其周边行业相关常用英语词汇
机床常用词汇punching machine 冲床robot机械手hydraulic machine油压机lathe车床|刨床?planer |'pleinmiller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to. to send delinery back to retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机机械词汇Piping work 铺管工程Steam trace 加热蒸汽管道Cutting 切割socket weld承插焊接fillet weld角焊,填角焊branch connection分支接续fabrication tolerance.制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding.密封焊接flange joint 凸缘接头undercut 底切feeder馈电线conduit outlet电线引出口seal fitting 密封接头, 密封配件Screw thread lubricant螺纹润滑剂Seal 绝缘层weld reinforcement 焊缝补强lock washer 锁紧[止动, 防松]垫圈electrical panel.配电板,配电盘nipple螺纹接头zinc plated.镀锌的ring joint 环接, 围缘接合bolt 螺栓control 控制器National Electrical Code 全国电气规程master schedule 主要图表, 综合图表, 设计任务书, 主要作业表torque wrench 转矩扳手job site 施工现场flange connection.凸缘联接Hard hat：安全帽Goggles：护目镜stockpile贮存packing list装箱单crate 柳条箱purchased material list原材料进货单back-feed反馈wire coil线盘，线卷，NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫terminal block线弧, 接头排接线盒, 接线板, 线夹power drill机械钻connector. 接线器insulated sleeve绝缘套管wire connector接线器wire terminal电线接头control wiring控制线路motor lead电动机引出线power wiring电力布线tender document．提供证件orifice plate.挡板nut 螺母flange gasket 法兰垫片dimensional inspection 尺寸检验burn through 烧蚀piping system.管道系统reinforcement of weld加强焊缝fabrication.制造dye penetrant examination染料渗透试验法magnetic particle examination 磁粉检验girth weld环形焊缝cement lined piping 水泥衬里weld joint 焊缝, 焊接接头spool drawing 管路图, 管路详图spot test 抽查, 当场测试butt weld 对接焊缝Random Radiography随机射线照相检查radiographic examination 射线照相检查assembly.装配erection 架设examination试验cable tray.电缆盘rigid steel conduit 钢制电线管power control 功率控制arc welding 电弧焊control cable控制电缆操纵索normal bend 法向[法线]弯管cable glands 电缆衬垫exfoliation剥落power receptacle 电力插座grounding conductor 接地导体lighting fixture照明器材junction box 分线箱race way 电缆管道terminal box接线盒distribution board配电盘, 配电屏receptacle 插座tumble switch.翻转开关,拨动式开关cathodic protection system 阴极保护系统Circuit breaker断路开关amplifier panel 放大器盘control console 控制台electrical material电气材料convenience receptacle.电源插座cable gland 电缆衬垫TIG：Tungsten-arc Inert-Gas welding 钨极电弧惰性气体保护焊filler rod焊条tensile strength 抗张强度shield gas 保护气体shield jig保护夹具high frequency generator.高频发电机welding rod 焊条filler metal 焊料, 焊丝shop fabrication 车间制造field installation 现场安装welding bead 焊道both sides welding.双面焊接residual stress 残余应力electrode 电焊条condensation 冷凝longitudinal.纵向的horizontal line 水平线circumferential joint 周圈接缝nondestructive examination.非破坏性检验, qualification 合格性construction work施工工程welded joint焊接缝焊接节点gas cutting.气割arc cutting电弧切割grind off 磨掉metallic luster 金属光泽Screwed Piping Joints螺丝状的管接头gouging .刨削槽Bending 挠曲witness test订货人在场的试验Welding 焊接Threading 车缧纹Leveling：校平color identification 彩色识别Alignment：对准,定位调整check against 检查, 核对Fixing：固定Console：控制台cubicle室,箱audit 审计material certificate.材料合格证vertical panel竖直面板power distribution panel 配电盘gauge board仪表板beveling 磨斜棱,磨斜边local panel 现场配电盘grouting 灌浆fabrication 加工,制造instrument rack 计测器支架tank gauge 液面计flushing 冲洗，填缝analyzer分析器piping管道敷设tubing敷设管道cable fitting电缆配件elbow.弯管接头main pipe 主管道bend.弯管弯头solvent 溶剂postweld heat treatment 焊后热处理jig.夹具arc gouging 电弧刨削chipping修琢machining 机械加工bridges.管式桥clamp.夹钳tack welding 点焊butt welding 对接焊grinder. 磨床commencement.开始gusset plate角撑板, 加固板process pipe 工艺管道land 纹间表面tee 三通管丁字钢T形梁opening 开口reinforcing pad.补强垫,增强衬板flux 焊剂wet developer 湿显像剂blowhole气泡,气孔inclusion 杂质imperfection 缺陷limitation 限度valve 阀,闸门structural attachment 结构附件tapered allowance 削尖余量tack welding 平头焊接sputter 喷溅scale 废料lateral translation侧向平移weld joint 焊缝, 焊接接头plug.塞fusion 熔融base material基底材料lead foil 铅箔intensifying screen 增光屏, 光增强屏pressure test.压力试验film density.影片密度line number行数leak test漏泄试验plate thickness 筛板厚度restoration修理field fabricated 工地制造的,现场装配的junction box.接线盒flow sheet 流程图vent 放气孔, 通风孔drain 排水管instrument air仪表气源blind挡板pipe arrangement 管配置civil engineer.土木工程师bus duct 母线槽substation分站flow instrument 流量计power distribution panel 配电盘level instrument 位面计, 水平仪pressure instrument 压力仪表/压力计level switch (信号)电平开关,gage glass 液位玻璃管pilot tube指示灯line check 小检修recalibration.复校,重新校准blinding plate盲板expansion joint 伸缩接头hydrostatic pressure test静水压试验pneumatic pressure 气压scaffolding脚手架check valve止回阀liquid penetrant examination液体渗透探伤test pump试验泵witnessed inspections 现场检测hanger吊架control valve控制阀,fabrication drawing 制造图纸,制作图schedule number表示管壁厚度系列的号码hydrostatic test .流体静力学试验,水压试验design pressure 设计压力disposition notice 处罚通知书pipe stanchion 管支柱bellow type 波纹管式expansion joint 伸缩接头vibration stopper：减震器subcontractor 转包商WPS Works Process Specification 典型工艺规程piping.管道系统flange.凸缘,sleeve 套筒ferritic .铁素体的identification mark 识别标志stencil.模绘片版,镂花模板stamping .冲压silicone paint硅树脂油漆weld bead 焊缝automatic temperature recorder 温度自动记录器penetrameter 透度计film viewer底片观察用光源civil works土建工程，建筑工程lump sum price 混合价格,统包价格scrap material废料caulking metal填隙合金[金属](材料) application drawing操作图, 应用图cable routing电缆路由选择channel bases沟渠基底vertical panel竖直面板local panel 现场配电盘power distribution panel 配电盘gauge board样板, 模板规准尺anchor bolt 锚定螺栓expansion bolt 伸缩栓, 扩开螺栓field instrument.携带式仪表instrument rack 计测器支架,计测器框架tank gauge 油箱液位计guide wire 尺度[定距]索,准绳name plate名牌, 商标lead pipe铅管take-off valve输出阀sub-header分联箱air header 集气管pneumatic signal气动信号steam trace 加热蒸汽管道electric heat tracing.电伴随加热cable trunk 电缆管道stop end封端fire barriers防火间隔bonding wire 接合线, 焊线conduit box [电]导管分线匣刚性导管rigid conduitsflexible conduit软管conduit entry 导管引入装置平交道口管道组road crossing duct bankCapping ends顶盖末端电缆铠装cable armor电缆包皮层Cable sheathsealing compound电缆膏coaxial cable同轴电缆loop test环路测试sequence test.联锁顺序试验lintel beam 水平横楣梁flash plate闪熔镀层anchor bolt 地脚螺栓expansion bolt伸缩栓, 扩开螺栓shim plate 垫板push button station按钮式控制站logic diagram逻辑图calculation sheet计算书flow instrument流量计level instrument 位面计, 水平仪layout drawing 布置图tie band捆扎用带材加热室Heating boxes切孔cutting openingcontrol valve actuator 阀控传动机构air set空气中凝固, 常温自硬自然硬化solenoid valve.螺线管阀,电磁阀calorimeter热量计odometer历程标tachometer转速计chronometer精密计时表机械设计及周边其它用语assembly drawing 装配图auto tool change cycle 自动换刀时间周期beam 横梁bending moment 弯矩bending stress 弯曲应力bottoming 底靠buckling 纵弯曲chamfering 去角斜切channel 凹槽chattering 颤动check point 查核点chip 切屑chip conveyor 排屑输送机coefficient of friction 摩擦系数compact 小型的cooling pipe 冷却管coupon 试样胚deflection 挠曲量distortion 扭曲变形draft taper 拔模锥度draw out 拉拔fit tolerance 配合公差flexible rigidity 弯曲刚性gas vent 气孔hatching 剖面线heater cooler 加热器冷却装置hook cavity 钩穴inching 寸动lug 凸缘maintenance 维修保固metallurgy 冶金学notch effect 切口效果out of roughness 真圆度performance 动作性能pit 坑plane strain 倒角应力plug mill 蕊棒轧管机repeated load 重复载荷riveted joint 铆钉接合sand paper 砂纸shift 偏移shrink fit 热压配合shrinkage hole 缩孔sinking 凹陷sketch 草图spalling 剥落straightness 直度submarine 深陷式surface roughness 表面粗度tapping 攻螺丝thermocouple 热电耦torsion load 扭转载荷toughness 韧性tracing 描图under cut 凹割O形密封圈密封O Ring SealV 带V Belt阿基米德蜗杆Archimedes Worm安全系数Safety Factor; Factor of Safety安全载荷Safe Load摆动从动件Oscillating Follower摆动从动件凸轮机构Cam With Oscillating Follower 摆动导杆机构Oscillating Guide-Bar Mechanism摆杆Oscillating Bar扳手Wrench板簧Flat Leaf Spring半圆键Woodruff Key包角Angle of Contact保持架Cage背对背安装Back-To-Back Arrangement背锥Back Cone; Normal Cone背锥角Back Angle背锥距Back Cone Distance标准齿轮Standard Gear标准直齿轮Standard Spur Gear槽轮Geneva Wheel槽轮机构Geneva Mechanism; Maltese Cross 槽凸轮Groove Cam侧隙Backlash插齿机Gear Shaper差动轮系Differential Gear Train成对安装Paired Mounting尺寸系列Dimension Series齿槽Tooth Space齿槽宽Space width齿侧间隙Backlash齿顶高Addendum齿顶圆Addendum Circle齿根高Dedendum齿根圆Dedendum Circle齿厚Tooth Thickness齿距Circular Pitch齿宽Face Width齿廓Tooth Profile齿廓曲线Tooth Curve齿轮Gear齿轮变速箱Speed-Changing Gear Boxes齿轮插刀Pinion Cutter; Pinion-Shaped Shaper Cutter 齿轮齿条机构Pinion And Rack齿轮滚刀Hob; Hobbing Cutter齿轮机构Gear齿轮联轴器Gear Coupling齿轮轮坯Blank齿式棘轮机构Tooth Ratchet Mechanism齿数Tooth Number齿数比Gear Ratio齿条Rack齿条插刀Rack Cutter; Rack-Shaped Shaper Cutter 齿形链、无声链Silent Chain齿形系数Form Factor传动比Transmission Ratio; Speed Ratio传动角Transmission Angle传动系统Driven System传动轴Transmission Shaft传动装置Gearing; Transmission Gear唇形橡胶密封Lip Rubber Seal从动带轮Driven Pulley从动件Driven Link; Follower从动件停歇Follower Dwell从动轮Driven Gear粗牙螺纹Coarse Thread打滑Slipping大齿轮Gear Wheel带传动Belt Driving带轮Belt Pulley单列轴承Single Row Bearing单万向联轴节Single Universal Joint单向推力轴承Single-Direction Thrust Bearing弹性滑动Elasticity Sliding Motion弹性联轴器Elastic Coupling; Flexible Coupling弹性套柱销联轴器Rubber-Cushioned Sleeve Bearing Coupling 当量齿轮Equivalent Spur Gear; Virtual Gear当量齿数Equivalent Teeth Number; Virtual Number of Teeth当量摩擦系数Equivalent Coefficient of Friction当量载荷Equivalent Load导程Lead导程角Lead Angle导键Feather Key倒角Chamfer等加等减速运动规律Parabolic Motion; Constant Acceleration And Deceleration Motion等径凸轮Conjugate Yoke Radial Cam等宽凸轮Constant-Breadth Cam等速运动规律Uniform Motion; Constant Velocity Motion低副Lower Pair垫片密封Gasket Seal垫圈Gasket调心滚子轴承Self-Aligning Roller Bearing调心球轴承Self-Aligning Ball Bearing调心轴承Self-Aligning Bearing顶隙Bottom Clearance定轴轮系Ordinary Gear Train; Gear Train With Fixed Axes 动平衡Dynamic Balance动平衡机Dynamic Balancing Machine端面参数Transverse Parameters端面齿距Transverse Circular Pitch端面齿廓Transverse Tooth Profile端面模数Transverse Module端面压力角Transverse Pressure Angle端面重合度Transverse Contact Ratio对称循环应力Symmetry Circulating Stress对心滚子从动件Radial (or In-Line) Roller Follower对心曲柄滑块机构In-Line Slider-Crank (or Crank-Slider) Mechanism对心移动从动件Radial Reciprocating Follower对心直动从动件Radial (or In-Line) Translating Follower 多列轴承Multi-Row Bearing多项式运动规律Polynomial Motion多楔带Poly V-Belt额定寿命Rating Life额定载荷Load Rating发生面Generating Plane发生线Generating Line法面参数Normal Parameters法面齿距Normal Circular Pitch法面模数Normal Module法面压力角Normal Pressure Angle法向齿距Normal Pitch法向齿廓Normal Tooth Profile法向力Normal Force法向载荷Normal Load法向直廓蜗杆Straight Sided Normal Worm 反转法Kinematic Inversion范成法Generating Cutting仿形法Form Cutting飞轮Flywheel非接触式密封Non-Contact Seal非周期性速度波动Aperiodic Speed Fluctuation分度圆Reference Circle; Standard (Cutting) Pitch Circle 分度圆柱螺旋角Helix Angle At Reference Cylinder分度圆锥Reference Cone; Standard Pitch Cone复合铰链Compound Hinge复合轮系Compound (or Combined) Gear Train刚体导引机构Body Guidance Mechanism刚性冲击Rigid Impulse (Shock)刚性联轴器Rigid Coupling钢丝软轴Wire Soft Shaft高度系列Height Series高副Higher Pair根切Undercutting工况系数Application Factor工作机构Operation Mechanism工作载荷External Loads工作阻力Effective Resistance公称直径Nominal Diameter公法线Common Normal Line共轭齿廓Conjugate Profiles钩头楔键Taper Key构件Link固定构件Fixed Link; Frame惯性力部分平衡Partial Balance of Shaking Force 惯性力平衡Balance of Shaking Force惯性力完全平衡Full Balance of Shaking Force 惯性主矩Resultant Moment of Inertia惯性主失Resultant Vector of Inertia滚刀Hob滚道Raceway滚动体Rolling Element滚动轴承Rolling Bearing滚动轴承代号Rolling Bearing Identification Code 滚针Needle Roller滚针轴承Needle Roller Bearing滚子Roller滚子半径Radius of Roller滚子从动件Roller Follower滚子链Roller Chain滚子链联轴器Double Roller Chain Coupling 滚子轴承Roller Bearing合成弯矩Resultant Bending Moment赫兹公式H. Hertz Equation花键Spline滑动率Sliding Ratio滑动轴承Sliding Bearing滑键Feather Key滑块Slider环面蜗杆Toroid Helicoids Worm环形弹簧Annular Spring回程Return回转体平衡Balance of Rotors机构Mechanism机构运动简图Kinematic Sketch of Mechanism 机架Frame; Fixed Link机器Machine机械Machinery机械动力分析Dynamic Analysis of Machinery 机械动力设计Dynamic Design of Machinery机械动力学Dynamics of Machinery机械平衡Balance of Machinery机械设计Machine Design; Mechanical Design 机械系统Mechanical System机械系统设计Mechanical System Design; MSD 机械效率Mechanical Efficiency基本额定寿命Basic Rating Life基圆Base Circle基圆半径Radius of Base Circle基圆齿距Base Pitch基圆压力角Pressure Angle of Base Circle基圆柱Base Cylinder基圆锥Base Cone极位夹角Crank Angle Between Extreme (or Limiting) Positions 极限位置Extreme (or Limiting) Position急回机构Quick-Return Mechanism急回特性Quick-Return Characteristics急回系数Advance-To Return-Time Ratio急回运动Quick-Return Motion棘轮Ratchet棘轮机构Ratchet Mechanism棘爪Pawl尖底从动件Knife-Edge Follower间隙Backlash间歇运动机构Intermittent Motion Mechanism 减摩性Anti-Friction Quality减速比Reduction Ratio减速齿轮Reduction Gear减速器Speed Reducer减速装置Reduction Gear简谐运动Simple Harmonic Motion渐开螺旋面Involute Helicoid渐开线Involute渐开线齿廓Involute Profile渐开线齿轮Involute Gear渐开线发生线Generating Line of Involute渐开线花键Involute Spline渐开线蜗杆Involute Worm渐开线压力角Pressure Angle of Involute键Key键槽Keyway交变应力Repeated Stress交变载荷Repeated Fluctuating Load交叉带传动Cross-Belt Drive交错轴斜齿轮Crossed Helical Gears胶合Scoring角接触球轴承Angular Contact Ball Bearing角接触推力轴承Angular Contact Thrust Bearing 角接触向心轴承Angular Contact Radial Bearing 角接触轴承Angular Contact Bearing。
机械专业英语词汇完整版
energy 动量 momentum
桁架 truss 轴线 axes 余子式 cofactor 逻辑电路 logic circuit 触发器 flip-flop 脉冲波形 pulse shape 数模 digital analogy 液压传动机构 fluid drive mechanism 机械零件 mechanical parts 淬火冷却 quench 淬火 hardening 回火 tempering 调质 hardening and tempering 磨粒 abrasive grain 结合剂 bonding agent 砂轮 grinding wheel 机械零件 mechanical parts 淬火冷却 quench 淬火 hardening 回火 tempering
拉床 broaching machine 拉孔 broaching 装配 assembling 铸造 found
流体动力学 fluid dynamics 流体力学 fluid mechanics
加工 machining 液压 hydraulic pressure
切线 tangent 机电一体化 mechanotronics
渗碳 carburization 电路 circuit
半导体元件 semiconductor element 反馈 feedback
发生器 generator 直流电源 DC electrical source
门电路 gate circuit 逻辑代数 logic algebra 外圆磨削 external grinding 内圆磨削 internal grinding 平面磨削 plane grinding
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
3-jaws indexing spacers 三爪、分割工具头a.t.c.system 加工中心机刀库aluminum continuous melting & holding furnaces 连续溶解保温炉balancing equipment 平衡设备bayonet 卡口bearing fittings 轴承配件bearing processing equipment 轴承加工机bearings 轴承belt drive 带传动bending machines 弯曲机blades 刀片blades,saw 锯片bolts,screws & nuts 螺栓,螺帽及螺丝boring heads 搪孔头boring machines 镗床cable making tools 造线机casting,aluminium 铸铝casting,copper 铸铜casting,gray iron 铸灰口铁casting,malleable iron 可锻铸铁casting,other 其他铸造casting,steel 铸钢chain drive 链传动chain making tools 造链机chamfer machines 倒角机chucks 夹盘clamping/holding systems 夹具/支持系统cnc bending presses 电脑数控弯折机cnc boring machines 电脑数控镗床cnc drilling machines 电脑数控钻床cnc edm wire-cutting machines 电脑数控电火花线切削机cnc electric discharge machines 电脑数控电火花机cnc engraving machines 电脑数控雕刻机cnc grinding machines 电脑数控磨床cnc lathes 电脑数控车床cnc machine tool fittings 电脑数控机床配件cnc milling machines 电脑数控铣床cnc shearing machines 电脑数控剪切机cnc toolings cnc刀杆cnc wire-cutting machines 电脑数控线切削机conveying chains 输送链coolers 冷却机coupling 联轴器crimping tools 卷边工具cutters 刀具cutting-off machines 切断机diamond cutters 钻石刀具dicing saws 晶圆切割机die casting dies 压铸冲模die casting machines 压铸机dies-progressive 连续冲模disposable toolholder bits 舍弃式刀头drawing machines 拔丝机drilling machines 钻床drilling machines bench 钻床工作台drilling machines,high-speed 高速钻床drilling machines,multi-spindle 多轴钻床drilling machines,radial 摇臂钻床drilling machines,vertical 立式钻床drills 钻头electric discharge machines(edm) 电火花机electric power tools 电动刀具engraving machines 雕刻机engraving machines,laser 激光雕刻机etching machines 蚀刻机finishing machines 修整机fixture 夹具forging dies 锻模forging,aluminium 锻铝forging,cold 冷锻forging,copper 铜锻forging,other 其他锻造forging,steel 钢锻foundry equipment 铸造设备gear cutting machines 齿轮切削机gears 齿轮gravity casting machines 重力铸造机grinder bench 磨床工作台grinders,thread 螺纹磨床grinders,tools & cutters 工具磨床grinders,ultrasonic 超声波打磨机grinding machines 磨床grinding machines,centerless 无心磨床grinding machines,cylindrical 外圆磨床grinding machines,universal 万能磨床grinding tools 磨削工具grinding wheels 磨轮hand tools 手工具hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组heat preserving furnaces 保温炉heating treatment funaces 熔热处理炉honing machines 搪磨机hydraulic components 液压元件hydraulic power tools 液压工具hydraulic power units 液压动力元件hydraulic rotary cylinders 液压回转缸jigs 钻模lapping machines 精研机lapping machines,centerless 无心精研机laser cutting 激光切割laser cutting for smt stensil 激光钢板切割机lathe bench 车床工作台lathes,automatic 自动车床lathes,heavy-duty 重型车床lathes,high-speed 高速车床lathes,turret 六角车床lathes,vertical 立式车床lubricants 润滑液lubrication systems 润滑系统lubricators 注油机machining centers,general 通用加工中心machining centers,horizontal 卧式加工中心machining centers,horizontal & vertical 卧式及立式加工中心machining centers,vertical 立式加工中心machining centers,vertical double-column type 立式双柱加工中心magnetic tools 磁性工具manifolds 集合管milling heads 铣头milling machines 铣床milling machines,bed type 床身式铣床milling machines,duplicating 仿形铣床milling machines,horizontal 卧式铣床milling machines,turret vertical 六角立式铣床milling machines,universal 万能铣床milling machines,vertical 立式铣床milling machines,vertical & horizontal 立式及卧式铣床mold & die components 模具单元mold changing systems 换模系统mold core 模芯mold heaters/chillers 模具加热器/冷却器mold polishing/texturing 模具打磨/磨纹mold repair 模具维修molds 模具nail making machines 造钉机oil coolers 油冷却器overflow cutting machines for aluminium wheels 铝轮冒口切断机p type pvc waterproof rolled sheet making plant p型pvc高分子防水pcb fine piecing systems 印刷电器板油压冲孔脱料系统pipe & tube making machines 管筒制造机planing machines 刨床planing machines vertical 立式刨床pneumatic hydraulic clamps 气油压虎钳pneumatic power tools 气动工具powder metallurgic forming machines 粉末冶金成型机presses,cold forging 冷锻冲压机presses,crank 曲柄压力机presses,eccentric 离心压力机presses,forging 锻压机presses,hydraulic 液压冲床presses,knuckle joint 肘杆式压力机presses,pneumatic 气动冲床presses,servo 伺服冲床presses,transfer 自动压力机pressing dies 压模punch formers 冲子研磨器quick die change systems 速换模系统quick mold change systems 快速换模系统reverberatory furnaces 反射炉rollers 滚筒rolling machines 辗压机rotary tables 转台sawing machines 锯床sawing machines,band 带锯床saws,band 带锯saws,hack 弓锯saws,horizontal band 卧式带锯saws,vertical band 立式带锯shafts 轴shapers 牛头刨床shearing machines 剪切机sheet metal forming machines 金属板成型机sheet metal working machines 金属板加工机slotting machines 插床spindles 主轴stamping parts 冲压机straightening machines 矫直机switches & buttons 开关及按钮tapping machines 攻螺丝机transmitted chains 传动链tube bending machines 弯管机vertical hydraulic broaching machine 立式油压拉床vises 虎钳vises,tool-maker 精密平口钳wheel dressers 砂轮修整器woven-cutting machines 织麦激光切割机wrenches 扳手铝轮冒口切断机overflow cutting machines for aluminium wheels离心压力机 presses,eccentric六角立式铣床 milling machines,turret vertical六角车床 lathes,turret螺栓,螺帽及螺丝 bolts,screws & nuts螺纹磨床 grinders,thread冷却机 coolers冷锻 forging,cold冷锻冲压机 presses,cold forging立式双柱加工中心 machining centers,vertical double-column type立式铣床 milling machines,vertical立式油压拉床 vertical hydraulic broaching machine立式刨床 planing machines vertical立式车床 lathes,vertical立式带锯 saws,vertical band立式加工中心 machining centers,vertical立式及卧式铣床 milling machines,vertical & horizontal 立式钻床 drilling machines,vertical联轴器 coupling连续溶解保温炉aluminum continuous melting & holding furnaces连续冲模 dies-progressive链传动 chain drive切断机 cutting-off machinescnc刀杆 cnc toolings曲柄压力机 presses,crank修整机 finishing machines舍弃式刀头 disposable toolholder bits润滑系统 lubrication systems润滑液 lubricants熔热处理炉 heating treatment funaces三爪、分割工具头 3-jaws indexing spacers伺服冲床 presses,servo输送链 conveying chains手工具 hand tools砂轮修整器 wheel dressers蚀刻机 etching machines外圆磨床 grinding machines,cylindrical搪磨机 honing machines搪孔头 boring heads卧式铣床 milling machines,horizontal卧式带锯 saws,horizontal band卧式加工中心 machining centers,horizontal卧式及立式加工中心machining centers,horizontal & vertical万能铣床 milling machines,universal万能磨床 grinding machines,universal镗床 boring machines弯曲机 bending machines弯管机 tube bending machines通用加工中心 machining centers,general铜锻 forging,copper铣头 milling heads铣床 milling machines无心磨床 grinding machines,centerless无心精研机 lapping machines,centerless压模 pressing dies压铸冲模 die casting dies压铸机 die casting machines油冷却器 oil coolers造链机 chain making tools造线机 cable making tools造钉机 nail making machines印刷电器板油压冲孔脱料系统 pcb fine piecing systems摇臂钻床 drilling machines,radial硬(软)板(片)材及自由发泡板机组 hard/soft and free expansion sheet making plant辗压机 rolling machines液压元件 hydraulic components液压冲床 presses,hydraulic液压动力元件 hydraulic power units液压工具 hydraulic power tools液压回转缸 hydraulic rotary cylindersp型pvc高分子防水p type pvc waterproof rolled sheet making plant刨床 planing machines牛头刨床 shapers其他铸造 casting,other其他锻造 forging,other模芯 mold core模具 molds模具维修 mold repair模具打磨/磨纹 mold polishing/texturing 模具单元 mold & die components模具加热器/冷却器 mold heaters/chillers 磨轮 grinding wheels磨削工具 grinding tools磨床 grinding machines磨床工作台 grinder bench平衡设备 balancing equipment气油压虎钳 pneumatic hydraulic clamps 气动冲床 presses,pneumatic气动工具 pneumatic power tools轴 shafts轴承 bearings轴承配件 bearing fittings轴承加工机 bearing processing equipment 肘杆式压力机 presses,knuckle joint铸铝 casting,aluminium铸铜 casting,copper铸造设备 foundry equipment铸钢 casting,steel铸灰口铁 casting,gray iron织麦激光切割机 woven-cutting machines 重力铸造机 gravity casting machines重型车床 lathes,heavy-duty主轴 spindles扳手 wrenches拔丝机 drawing machines保温炉 heat preserving furnaces插床 slotting machines齿轮 gears齿轮切削机 gear cutting machines冲压机 stamping parts冲子研磨器 punch formers超声波打磨机 grinders,ultrasonic车床工作台 lathe bench磁性工具 magnetic tools传动链 transmitted chains床身式铣床 milling machines,bed type带传动 belt drive带锯 saws,band带锯床 sawing machines,band电脑数控镗床 cnc boring machines电脑数控弯折机 cnc bending presses电脑数控铣床 cnc milling machines电脑数控线切削机 cnc wire-cutting machines电脑数控磨床 cnc grinding machines电脑数控车床 cnc lathes电脑数控电火花线切削机 cnc edm wire-cutting machines 电脑数控电火花机 cnc electric discharge machines电脑数控雕刻机 cnc engraving machines电脑数控机床配件 cnc machine tool fittings电脑数控剪切机 cnc shearing machines电脑数控钻床 cnc drilling machines电动刀具 electric power tools电火花机 electric discharge machines(edm)雕刻机 engraving machines刀片 blades刀具 cutters倒角机 chamfer machines多轴钻床 drilling machines,multi-spindle锻铝 forging,aluminium锻压机 presses,forging锻模 forging dies仿形铣床 milling machines,duplicating粉末冶金成型机 powder metallurgic forming machines 反射炉 reverberatory furnaces钢锻 forging,steel高速车床 lathes,high-speed高速钻床 drilling machines,high-speed管筒制造机 pipe & tube making machines滚筒 rollers工具磨床 grinders,tools & cutters攻螺丝机 tapping machines弓锯 saws,hack虎钳 vises换模系统 mold changing systems夹盘 chucks夹具 fixture夹具/支持系统 clamping/holding systems剪切机 shearing machines加工中心机刀库 a.t.c.system激光切割 laser cutting激光雕刻机 engraving machines,laser激光钢板切割机 laser cutting for smt stensil集合管 manifolds矫直机 straightening machines金属板成型机 sheet metal forming machines 金属板加工机 sheet metal working machines 锯片 blades,saw锯床 sawing machines卷边工具 crimping tools晶圆切割机 dicing saws精密平口钳 vises,tool-maker精研机 lapping machines可锻铸铁 casting,malleable iron快速换模系统 quick mold change systems 卡口 bayonet开关及按钮 switches & buttons钻石刀具 diamond cutters钻头 drills钻模 jigs钻床 drilling machines钻床工作台 drilling machines bench自动压力机 presses,transfer自动车床 lathes,automatic注油机 lubricators转台 rotary tables。