产品缺陷中英文对照表
验货缺陷中英文对照供大家参考
. 验货缺陷中英文对照供大家参考carton marking wrong/箱唛错carton was damaged/箱烂carton wrinkle/箱邹poor printing on carton/箱唛印刷不良carton marking illegible/箱唛不清楚carton too tight/箱太紧bar code wrong/电脑纹错wrong printing on carton/箱印刷错bar code illegible/电脑纹模糊missing date code/漏日期贴纸missing bar code/漏电脑纹missing vendor code/漏厂编号missing product inside carton./漏装产品carton joint opened/箱驳口开裂carton unsealed/外箱无密封glue mark on carton/外箱胶水印gift box unseal/彩盒无密封gift box crushed/彩盒压烂压皱master carton/外箱shipping carton/落货箱inner carton/内箱blister pack/吸塑袋gift box pack/彩盒袋display box pack/开口彩盒solid pack/独立装assortment pack/混合装bulk pack/散包装cable tie/扎线带shrink warp/吸塑包装whole pack/完整包装bilingual pack/两种语言装gift box dirty/soil/彩盒污糟gift box wrinkle/彩盒皱gift box scratched/彩盒刮伤gift box deformed/dent/彩盒变形/凹陷gift box illegible/彩盒字迹模糊gift box wet/彩盒湿gift box poor sealing/彩盒封口不良gift box unsealed/彩盒无封口gift box flap seam opened/彩盒盖破裂tape poor sticking/胶纸粘贴不良gift box color deviation/彩盒颜色偏差poor printing on gift box/彩盒印刷不良gift box abrasion/彩盒擦伤gift box adhesion/彩盒相粘window box film damaged/彩盒胶窗烂window box film stress/彩盒胶窗顶白window box film dent/彩盒胶窗凹陷window box film detach/彩盒胶窗脱落window box film poor sealing/彩盒胶筒粘合不良window box film poor transparency/彩盒胶袋透明度不够foreign brand model/错型号wrong destination label/错目的地贴纸no suffoca tion warring on poly bag/胶袋无警告字语no recycling mark/无环保贴纸missing serial number/漏号码贴纸serial number don’t correspond/号码与彩盒不符missing label/漏贴纸missing manual/漏说明书missing accessories/漏附件gift box slightly damage/彩盒轻微损坏uneven coloring/颜色不平均illegible printing/印刷模糊wrong/missing coloring/错/漏颜色missing printing/漏印刷字句missing caution tags for transit漏搬运小心贴纸blister card was dirty/soil卡片是肮脏的/土壤insert(cardboakd)wrinkle 皱纹blister card damaged卡片损害blister card incorrect 备置卡片不正确的cardboard color deviationcardboard 彩色偏离shrinkage缩水deformed变形flash/gate remnantmatted无光泽flow line/stress mark夹水纹/顶白poor molding喷塑不良contamination mark混色，混料mark 痕迹,污点,标记colourized 混色color deviation 颜色偏差color mismatched 颜色不配合burnt mark 烧焦痕damaged 烂/损坏poor trimming 修整不良dull surface 哑色poor spraying 喷油不良over spraying 飞油paint under coverage油太薄paint chipped off脱油orange peel painting油面呈橙皮壮foreign painting染油poor re-painting touchup补油不良missing spraying漏喷油dirty on paint surface油面有尘点paint bubbles油泡paint color deviation油颜色偏差paint color mismatched喷油颜色不配合paint abrasion fail油漆被擦paint adhesion fail油漆被甩paint dirty油面污糟spraying scratched喷油刮花dull of paint surface喷油哑色paint matted/frayed喷油无光泽/磨损yellowish painting油面发黄paint peel off 油面起皮spraying uneven喷油不整齐paint damped油漆不干paint abrasion甩油bubble冒泡，气泡uneven paint coverage喷油厚薄，不均paint misregistration错色poor coating油漆外层不良塑胶原料6 `9 K9 B% c6 e$ _' r- I. Lacrylic 压克力casein 酪素" m a( B% `, y3cellulose acetate 醋酸纤维素CA 2 F(cellulose acetate butyrate 醋酸丁酸纤维素CAB 3 ?2 v9 [ composite material 复合材料cresol resin 甲酚树脂CF' J% y# F" V8 [4 g7 P4 F% `dially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料" h) Z8 \' engineering plastics 工程塑胶epoxy resin 环氧树脂EP + X' c# A' n$ v. D( L5 j ethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVA) s4 x5 o- P; k1 ]; iethylene-vinlacetate copolyme 醋酸乙烯共聚物EV A expanded polystyrene?泡聚苯乙烯EPS C+ h2 L# h7 fiber reinforcement 纤维强化热固性/纤维强化复合材料9 C! p4 O, d1 ] Qhigh density polyethylene 高密度聚乙烯HDPE + \0 ~4high impact polystyrene 高冲击聚苯乙烯HIPS0 y* f$ W& C& Q' Shigh impact polystyrene rigidity 高冲击性聚苯乙烯8 t9 t" r1 F9 T' C' V1 h% P9 N( llow density polyethylene 低密度聚乙烯LDPEmelamine resin 三聚氰胺酚醛树脂MFnitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑胶polyacrylic acid 聚丙烯酸PAP1 z6 H+ Z* G4 p9 B5 D! hpolyamide 耐龙PA polybutyleneterephthalate 聚对苯二# u" G- d6 U5 b9 g* N4 a; H/ }甲酸丁酯PBT( \' ~( S6 P0 p/ `polycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFG, d8 y( L# Q; |polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETPM5 |4 x( n* L& `7 o- o: ~polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POM ; q, Y! O/ K- \3 }7 F: spolyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPO ) i. ~( q* y/ C) E$ ?( P* ? polypropylene 聚丙烯PPpolystyrene 聚苯乙烯PS 6 v6 j+ n B+ i; `2 J polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯?, T) q4 [$ N4 U( \( O% F+ M. @- Mpolythene 聚乙烯PE polyurethane 聚氨基甲酸酯PU! S/ X! K4 i7 a4 Jpolyvinylacetate 聚醋酸乙烯PV AC polyvinylalcohol 聚乙烯醇PV A 9 _# n1 n$ p# r X polyvinylbutyral 聚乙烯醇缩丁醛PVBpolyvinylchloride 聚氯乙烯PVC+ @5 W; K- a6 Ipolyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC; b+ O. ~) T9 M Wprepolymer 预聚物silicone resin 矽树脂' I8 i+ q3 T$ m5 b7 Nthermoplastic 热塑性thermosetting 热固性- w7 B5 e% A- @% sthermosetting plastic 塑胶unsaturated polyester 不饱和聚酯树' x3 _1 {, h8 ?+ J- n脂# H: o/ q3 G# p# n, a成形不良用语8 ?1 d7 D; {4 Kaberration 色差atomization ?化8 q. ^& J5 U7 ^0 z2 h- Xbank mark ?料纹bite 咬入0 }( q5 { P$ u) i1 hblacking hole 涂料孔(铸疵)blacking scab 涂料疤; j. f. i! }7 k3 f5 M! l. u/ Vblister 起泡blooming 起霜: Y) g" J. |, ^blow hole 破孔blushing 泛白9 Q% h/ n% U8 [+ W! _+ rbody wrinkle 侧壁皱纹breaking-in 冒口带肉% F* {3 m' A2 r6 a: Z _" Xbubble 膜泡burn mark 糊斑/ t1 s* c) l# e) [: fburr 毛边camber 翘曲- h) }; U: m7 B7 _8 G3 zcell 气泡center buckle 表面中部波皱% {; t' j7 E# Z7 @# u- @check 细裂痕checking 龟裂* q6 c: @6 @6 {. C. F4 gchipping 修整表面缺陷clamp-off 铸件凹痕% f! ~" B! W0 C% C1 b% |& u; n collapse 塌陷color mottle 色斑# r: W) m# K. T0 `$ tcorrosion 腐蚀crack 裂痕6 h& J9 G4 g: `+ mcrazing 碎裂crazing 龟裂' \! X+ X# e8 C1 E4 O7 ]- Vdeformation 变形edge 切边碎片$ e( Z6 y/ x9 q6 t1 wedge crack 裂边fading 退色3 z0 i* B7 L" Q1 \) Ofiller speak 填充料斑fissure 裂纹; M, Z- N0 W- j% ~flange wrinkle 凸缘起皱flaw 刮伤& e# j4 H) y# A/ Y" n2 X* Eflow mark 流痕galling 毛边2 b8 D) D( Z' J- P, Dglazing 光滑gloss 光泽 a4 P, C2 `) Kgrease pits 污斑grinding defect 磨痕( E, e. C& W( T% }! l+ i3 thaircrack 发裂haze 雾度% u" a3 V; Z% D5 V, ^# g- Jincrustation 水锈indentation 压痕) m5 \& N6 g; Z0 j! uinternal porosity 内部气孔mismatch 偏模$ f/ g( f! X% e' X Umottle 斑点necking 缩颈7 D& b3 b0 y+ Znick 割痕orange peel 橘皮状表面缺陷& v G2 t! R+ C8 e2 Z overflow 溢流peeling 剥离" r x0 D2 J9 ]/ p2 e* Q8 _ Wpit 坑pitting corrosion 点状腐蚀# j8 |$ g, R% Hplate mark 模板印痕pock 麻点2 p: }+ J4 r0 J) d: Lpock mark 痘斑resin streak 树脂流纹6 J# y1 m# g$ j/ Fresin wear 树脂脱落riding 凹陷. {- Y" A& G1 csagging 松垂saponification 皂化/ X$ A: S7 A' C" kscar 疤痕scrap 废料6 E! g+ Z a3 k7 x, o/ e' _scrap jam 废料阻塞scratch 刮伤/划痕& D% b1 q& X- s) Qscuffing 深冲表面划伤seam 裂痕. c4 v" u' _3 Eshock line 模口挤痕short shot 充填不足5 T+ I7 L/ B/ lshrinkage pool 凹孔sink mark 凹痕* y4 z8 g z7 B) m' _skin inclusion 表皮摺叠straightening 矫直' W5 m5 Q( { q0 S7 astreak 条状痕surface check 表面裂痕" {' i3 v3 Y4 i2 H1 i( ]# Csurface roughening 橘皮状表皮皱摺surging 波动" c! L- d8 n E: O/ @( Isweat out 冒汗torsion 扭曲- m; r" B- w; Z* Z+ p9 {9 |: Fwarpage 翘曲waviness 波痕$ _; J: R$ n: Fwebbing 熔塌weld mark 焊痕+ m# Q w* N9 S p1 Y4 ~whitening 白化wrinkle 皱纹% K# K8 p; S4 Y! Q模具常用刀具与工作法用语6 m* U5 h* P: z/ I; i' V8 ladjustable spanner 活动扳手angle cutter 角铣刀anvil 铁?arbour 心轴; n8 B# s" K1 G8 P( @% s4 w- Z obacking 衬垫belt sander 带式打磨机" @: } Y0 p& ?buffing 抛光chamfering machine 倒角机, ]8 @2 o- q: T2 i chamfering tool 去角刀具chisel 扁錾+ n$ g- Q( [% F c2 N; Y {& Jchuck 夹具compass 两角规& h+ X" g3 D% }/ z+ U+ @4 Dconcave cutter 凹面铣刀convex cutter 凸形铣刀+ L+ C3 i! U1 Q( e/ rcross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头1 [7 i) U6 K6 s5 xgrinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线1 I; Y1 W! } K" [1 ^% E/ shexagon headed bolt 六角头螺栓hexagon nut 六角螺帽, n: M$ t& [# T6 s+ y5 Aindex head 分度头jack 千斤顶% F4 i. r- Q9 ~/ K% yjig 治具kit 工具箱, f% |; r Y( W: ~. N7 n3 S5 c& l! Tlapping 研磨metal saw 金工锯0 B6 g6 N @# G2 r1 y4 p* snose angle 刀角pinchers 钳子$ H3 _2 a) s! g1 spliers 铗钳plug 柱塞头! k' ]& b X6 m( v% mpolisher 磨光器protable driller 手提钻孔机5 v, L; S& E. Z; u5 Epunch 冲头sand paper 砂纸0 E8 b H+ `# D( f( K5 j! Sscraper 刮刀screw driver 螺丝起子) S" Q$ `# S9 }+ k+ p( c. O scribing 划线second out file 中纹锉* V5 B$ i* |1 a& A: l- yspanner 扳手spline broach 方栓槽拉刀+ \0 Z& H" c: M$ V, b; I1 Ysquare 直角尺square sleeker 方形镘刀3 ]! f6 l7 ~7 u' ]4 \2 Jsquare trowel 直角度stripping 剥离0 O& t; ?' Y0 i! o/ x! V2 a工具1 q( S+ I4 g: N7 uT-slot T形槽tool for lathe 车刀7 Q; S! [/ q1 M6 J) S: T) Wtool point angle 刀刃角tool post 刀架4 p+ A5 c: J8 I2 N4 A2 Atosecan 划线盘trimming 去毛边# | E2 ]+ P. Q2 ]% M7 J2 nwaffle die flattening 压纹效平wiper 脱模钳# Q% {7 o# C) j* ?9 ?8 W9 S7 bwrench 螺旋扳手8 u9 B+ a: h% Z4 Q# T0 y* I电脑关联用语0 Z6 ]9 ^5 q B% l; M5 c7 Y; v3D modeling 三次元模拟access 通路; B2 J: L4 K" s6 G# ~+ H7 [animation 卡通影片application 应用% F% `. t3 r( s0 E8 {7 g4 b0 Qboard 基板bug 故障, O3 X" B8 g: u; Y" m/ s$ v; [5 O* Qbus 汇流排CAD 电脑辅助设计: B/ [/ |% ^* u+ w; \CAE 电脑辅助工程分析CAM 电脑辅助制造" ?; ]9 O3 j- x$ [( \: ecassette 卡座color display 彩色显示器& w; k9 @; R: ?0 m, a+ ^ command 指令communication 通信" n+ \; d& K9 B- s( Bcompact 精简小型computer 电脑" H) {* p. T1 ?* ] V( dcopy 复制cursor 游标0 C$ T1 U- A! Scurve modeling 曲面模拟database 资料库5 r: x7 n6 u+ R+ X- Y4 _design 设计digitizing 数位化7 o" \6 {$ y" Zdisk 磁碟dot 点% `; o. M* M8 O& M) Q8 l$ H1 x- Qeyelet 眼孔floppy 磁碟片.& }; {: P m( @1 L& ]format 格式化graphic 圆解! p+ Z/ @6 f" l' \ \6 s: {hardware 硬体honeycomb 蜂巢: \. s5 C: K/ Ainterface 界面know how 秘诀) p' {9 ?+ Z* v: Flaser printer 雷射印表机lay out 布置0 [) o5 V* T2 ]memory 记忆memory swap 交换记忆. W/ @3 Y% z1 D microprocessor 微处理器modeling 造型" _9 C! m3 M8 p& j8 pmodule 模组monitor 萤幕1 W1 ? \+ U& c- S9 F+ g2 O- o. Z4 s mouse 滑鼠need 需求& i: V/ i4 f2 q$ T6 D! C1 Anetwork 网路new version 新版+ I! Y0 R/ }$ F6 Fon line 上线中option 选择1 V- `+ Z0 S m/ r& ^PC 个人电脑plotter 绘图机3 z! |; m# H. x$ w* rprogram 程式scanning 扫描! h8 ]4 h3 h6 ^1 x- O) ~simulation 模拟software 软体% H7 b8 j2 r: Bsolid model 实体模型system 系统8 F/ u1 I3 X* d9 w8 ]) A8 u' Gtape 磁带terminal 终端机, Z. A6 \+ K: F# i) x% Q* Mtexture 构造trim 修边6 ~ h( w& s# p. b* [0 p( |venter 排气风扇word processor 文书处理器6 J3 D' ^: D# y% \+ n' l! O各种冲模加工关连用语6 \0 v: A3 X/ M5 ibarreling 滚光加工belling 压凸加工( v L& s/ x6 T- ]$ _bending 弯曲加工blanking 下料加工. J8 a. ]& [* z. n# p7 hbulging 撑压加工burring 冲缘加工0 n7 F3 @# E# c0 }6 icam die bending 凸轮弯曲加工caulking ?合加工/ l: }& ?. ~$ w3 l, [! S1 ~coining 压印加工compressing 压缩加工6 b: w- p; X* p( U% Hcompression bending 押弯曲加工crowning 凸面加工7 ]: P8 ^) b/ _* M, |2 Kcurl bending 卷边弯曲加工curling 卷曲加工8 {% p9 s5 z8 p3 wcutting 切削加工dinking 切断蕊骨- F% B0 w M, s! v4 Odouble shearing 叠板裁断drawing 引伸加工/ K6 p0 q0 w9 i$ Udrawing with ironing 抽引光滑加工embossing 浮花压制加工6 a5 a) v" A3 x" h A1 t! \ extrusion 挤制加工filing 锉削加工/ m0 u, r- Z- o& ]; Zfine blanking 精密下料加工finish blanking 光制下料加工5 }: T- C1 F: B' {" V; wfinishing 精整加工flanging 凸缘加工! w& f5 F# r" B6 t# mfolding 折边弯曲加工folding 摺叠加工/ [: t7 c9 D* P9 i5 w! ~forming 成形加工impact extrusion 冲击挤压加工2 o. [1 j6 v2 }; t- |) e: Xindenting 压痕加工ironing 引缩加工* L( j3 Y) y" W# Y2 D, ~knurling 滚花lock seaming 固定接合9 j0 ?& d( m1 S9 M$ }7 B) r4 i+ mlouvering 百叶窗板加工marking 刻印加工' t* `1 m1 Y4 b, y9 m- B4 inecking 颈缩加工notching 冲口加工% ~% [' E5 ], T6 V! N) w' R- iparting 分断加工piercing 冲孔加工8 e+ W$ c) O/ _/ j( R& Aprogressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工+ P/ m0 E6 q6 L4 X reaming 铰孔加工restriking 二次精冲加工7 w( I8 b. T) O1 A( wriveting ?接加工roll bending 滚筒弯曲加工% y1 J% I3 Y d$ P. t+ D# e! L) J roll finishing 滚压加工rolling 压延1 s. `( ]8 S# E8 f加工, B# a# `3 r& k' o7 |7 f1 r1 p6 R! `+ droughing 粗加工scrapless machining 无废料加工* ^6 k1 q* L* `9 g _ seaming 折弯重叠加工shaving 缺口修整加工.0 n: O5 F5 i7 ]% ]shearing 切断加工sizing 精压加工/矫正加工/ q+ j" \5 V" C z/ }/ A8 ~ slitting 割缝加工spinning 卷边?接- Q" I- u8 |7 q4 \( L6 N1 a6 ostaking ?固stamping 锻压加工& V/ h$ X3 E9 L% X0 x- I2 s swaging 挤锻压加工trimming 整缘加工: P. W1 x* C/ E- Vupsetting 锻粗加工wiring 抽线加工6 N% t1 ]% j/ m冲压机械及周边关连用语$ L; B! X( X' G* e5 {4 N! X9 oback shaft 支撑轴blank determination 胚料展开* k8 ]' b2 ]$ L7 Mbottom slide press 下传动式压力机board drop hammer 板落锤! q. b% ]5 K5 V, K- ?, A brake 煞车buckle 剥砂面8 ?- ~ j5 Y5 ^. p ~0 z/ jcamlachie cramp 铸包casting on flat ?合: s& I C6 W ~; T" _chamotte sand 烧磨砂charging hopper 加料漏斗3 [$ d! F$ v0 }" q4 O' I clearance 间隙closed-die forging 合模锻造R5 q9 d& Q: W7 W- g- {clump 夹紧clutch 离合器# X3 H4 Y: N& o/ s$ fclutch brake 离合器制动器clutch boss 离合器轮壳& w- \& y! a1 o: C7 Yclutch lining 离合器覆盖coil car 带卷升降运输机! k: Q" S& X1 u) G# k$ q3 Q1 ycoil cradle 卷材进料装置coil reel stand 钢材卷料架% Z! K$ @! K n! j8 _column 圆柱connection screw 连杆调节螺钉: B6 V6 M1 s& \: G( h4 E core compound 砂心黏结剂counter blow hammer 对击锻锤8 {( F( ?2 \+ U# i L2 K' ? cradle 送料架crank 曲柄轴/ C% ^ t D& j# ]crankless 无曲柄式cross crank 横向曲轴0 R; Q, W o: s4 L) Ecushion 缓冲depression 外缩凹孔0 ?: `- _4 l; F' i, odial feed 分度送料die approach 模口角度6 y: @- |) G' G' [% I0 kdie assembly 合模die cushion 模具缓冲垫* ^. O/ x: F- C" g2 R }die height 冲压闭合高度die life 模具寿命% e. B& v% l6 w0 r, s) G5 n2 udie opening 母模逃孔die spotting press 调整冲模用压力机/ _ m/ ?5 O( _ e4 j# Rdouble crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂$ r% _: g0 q% W; d' `0 f& qfilm play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼後熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦3 L+ `% ^6 ]" j- x( U. Zfriction brake 摩擦煞车gap shear 凹口剪床+ F/ B7 X( U9 N6 t: y+ t% Y$ s) Cgear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机/ S/ ?9 t; [! _" Z9 ^0 thand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模. S0 E# B5 | @; _micro inching device 微寸动装置.microinching equipment 微动装置/ [( i B: e9 X1 _% J$ g" `, Qmotor 马达moving bolster 活动工作台9 [9 {2 h9 ^1 [4 G. |. tnotching press 冲缺口压力机opening 排料逃孔1 R- k7 E+ K% `* H7 D. ]" B overload protection device 防超载装置pinch roll 导正滚轮0 `5 r" c* }/ T/ K/ n/ h, i8 l& v, k- ipinion 小齿轮pitch 节距1 }' ~2 A$ a% o9 bpressfit 压入progressive 连续送料! g. I( E7 R( N7 }pusher feed 推杆式送料pusher feeder 料片押片装置" u W6 e% N: E5 N0 T: A& K! Gquick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料6 L; a; b( O' z- h/ [" grobot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机. e+ K- M o9 R6 b! a& O$ D, t% i qrotary bender 卷弯成形机safety guard 安全保护装置' z2 x8 |: o( x8 u' D: Z. iscrap cutter 废料切刀scrap press 废料冲床s$ W3 l- x, H [3 k6 r' z4 V fseamless forging 无缝锻造separate 分离9 g1 x6 b3 m2 L' X x8 Pshave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作- n4 C& I# ]& ?) y/ kshrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴5 X" F6 }( M) E7 j w$ mslide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模( v+ v: X; Q2 L' a% b- V/ Ostack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置, D* R& h1 i0 I8 x# o2 K: H! O. n3 L& t/ Ntoggle press 肘杆式压力机transfer 传送- X, N% [" Z& U transfer feed 连续自动送料装置turrent punch press 转塔冲床: O/ H) o9 G# o S$ Ttwo speed clutch 双速离合器uncoiler 闭卷送料机8 o" `& A3 e# H" q0 ?3 Iunloader 卸载机vibration feeder 振动送料机' Z: o0 G' p; `# Ewiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电arc discharge 电弧放电0 [: O* H+ @/ J- Tbelt 皮带centreless 无心chrome bronze 铭铜clearance angle 後角# k, u9 U. I8 A+ ^0 D$ _9 m+ qcorner shear drop 直角压陷deflection 桡曲度discharge energy 放电能量dressing 修整8 ]! g7 M2 n: v/ r7 [' [. vdwell 保压flange 凸缘gap 间隙graphite 石墨2 U) y& y1 |" {. S. igraphite contraction allowance 电极缩小余量graphite holder 电极夹座& \2 z( z9 }! V3 x6 dhair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极& u, i! p* g4 N o0 n3 x! f" bpulse 脉冲rib working 肋部加工; Z9 W3 {" G( q# ~2 troller electrode 滚轮式电极rotary ( H4 Q" G/ n8 `) k- V& D' P! gsurface 旋转面; l/ n( V" r* M" Z" \shank 柄部sharp edge 锐角部2 H5 g+ C! v# @ N) l% I. Utough bronze 韧铜traverse 摇臂# a/ i% B4 T x2 jtungsten bronze ?青铜waviness 波形起伏.work 工件working allowance 加工余量1 z4 j2 ^0 U U+ ^" v1 lworking dischard 加工废料锻铸造关连用语$ i$ M# E( z4 v: a6 kaccretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉3 }' B- b& E: E( R( ^+ Haerator 松砂机air set mold 常温自硬铸模+ C" S/ d( v& z$ Bairless blasting cleaning 离心喷光all core molding 集合式铸模, a3 ~- c9 O- L/ Yall round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂0 t9 y; v1 T- kbase bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔3 l, P/ |7 a/ wboard drop hammer 板落锤bottom pour mold 底浇7 Z" D# v2 e4 N6 o* q( Pbottom pouring 底注boxless mold 脱箱砂模塑胶产品常见不良描述的中英文对于照blister起泡blooming起霜blow hole破孔blushellong泛白body wrinkle侧壁皱纹儿breaking-in冒口带肉bubble膜泡burn mark糊斑burr毛边camber翘曲cell气泡儿center buckle外貌中部波皱check细裂缝checking龟裂chellopping修整外貌缺陷clamp-off铸件凹痕collapse沉陷color mottle色斑corrosion腐蚀crack裂缝crazing碎裂crazing龟裂deformation变型edge切边碎片edge crack裂边fading退色filler speak填充料斑fissure裂纹flange wrinkle凸缘起皱flaw刮伤flow mark流痕galling毛边glazing光滑gloss光泽grease pits污斑grinding defect磨痕haircrack发裂haze雾度incrustation水锈indentation压痕internal porosity内部气眼mismatch偏模mottle雀斑necking缩颈nick割痕orange peel橘皮状外貌缺陷overflow溢流peeling剥离pit坑pitting corrosion点状腐蚀plate mark模型板印痕pock麻点pock mark痘斑resin streak树脂流纹resin wear树脂脱落riding凹陷sagging松垂sap onification皂化scar疤痕scrap废料scrap jam废料阻塞scratch刮伤/划痕scuffing深冲外貌划伤.seam裂缝shock line模口挤痕short shot充填不足shrinkage pool凹孔sink mark凹痕skin inclusion表皮折迭straighte ning矫直streak条状痕surface check外貌裂缝surface roughening橘皮状表皮皱折surging波动sweat out冒汗torsion扭曲warpage翘曲waviness波痕webbing熔塌weld mark焊痕whellotening白化wrinkle皱纹儿missing part漏件wrong part错件excessive defects过多的缺陷critical defect极紧张缺陷major defect首要缺陷minor defect非主要缺陷not up to standard分歧规格dimension/size is alittle bigger尺寸偏大(小) cosmetic defect外不雅不良slipped screwhead/slippery screw head螺钉狡徒slipped screwhead/shelloppery screw thread滑手speckle雀斑mildewed=moldy=mouldy发霉rust生锈deformation变型burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大塑胶产品缺陷grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage抽水mixed color杂色scratch划伤手机组常见不良的英文表示Dirty脏污foreign material result in discoloration or dust on surface外来物所致的变色或吸附在零件表面上的异物Spot斑点printing ink on the clear surface of the lens or foreign substance in the material在镜片的透明表面有印刷油墨或原料中有杂质Foreign Material杂质dust or other particles embedded in the painted surface灰尘或其他颗粒埋在涂层中Discoloration色差surface is different from standard color整体的外观面与标准颜色有差异Black & White Dot异色点surface have aberration (such as shape have a point or line or block )外观面中局部的颜色差异（如点状、线状、块状）Scratch 刮伤foreign matters result in surface of eyeable scar 外来硬物碰擦、划伤造成的可见的表面伤痕Deformation变形appears shape be changed in part 局部形狀产生变异Fibre毛丝fibre fall into paint空气中的纤维丝附着产品表面Gap间隙gap appear between two or more parts link surface两个或多个零件结合面之间的缝隙Step断差vertical step of parts on surface零件同一段面高度差Poor Elasticity弱弹The keypad returns to elasticity to have no dint按键回弹力无力Sink凹陷be knocked or press result in surface dent因撞击或压力造成的表面不连续下凹Sand Hole沙眼small crater on surface表面上的小凹印Protrusion突起bump or apophysis of parts surface零件表面之肿块或隆起Burr毛边appears scratch ,protrusion in sharp edge or hole有划伤力，在沿边或孔上呈突起状Dimension NG尺寸不良dimension beyond the specification尺寸超出图面规格Orange桔皮surface appears wavy or uneven表面起波纹或不均匀Polish Mark磨纹appears mark after sanding打磨后的痕迹NGGloss NG光泽.gloss appears inconsistent or incorrect光泽度表面不一致或不正确Crack裂纹appears little gap on surface NG 在材料表面产生的细小缝隙Flatness平面度flatness NG平面度不合格Fitting实配beyond specification after assembly与实体组装后相关项目超出规格Deformity 缺料single part deformity单件本身少料Uneven Color阴阳面appear color inconsistent on same surface同一产品上表面的颜色不一致Push & pull Force推/拉力push/ pull force out of specification推/拉力测试值超出规格Film Thickness膜厚film thickness out of specification膜厚测试值超出规格Abrasion耐磨耗abrasion out of specification耐磨耗测试值超出规格Adhesion附着力adhesion out of specification附着力测试值超出规格Oil Contamination油污foreign oil adhere to parts surface粘附在零件表面上外来油脂Poor Printing印刷不良the defect with unclear, missing, moving or double print印刷图案不清，残缺，偏移或重叠等印刷形成的缺失Broken破损零件被撞坏parts be damaged缺件Missing Part 组件少装零件assembly missing压印Marks 表面上砂眼、砂纸打磨、加工等印痕Pits, sanding, machining or other marks on part surface积油Wedging 涂层顶部薄底部厚Coating is thin at top and thick at bottom起泡Blistering 涂层中有气泡或水泡The formation of hollow bubbles or water droplets in a paint film剝落Peeling 油漆没有粘附到产品上Paint fails to adhere to the part.多料Extra Material 零件本身多料single part Extra Material缩水 Sink 表面上因压力不够引起的收缩 Shrink resulting in a depression on surface其他Other 未有明确定义之缺失或不良现象definition missing or defect phenomena not clearly2.组装缺陷Assemble Defect热熔不良Heat Stacking NG 热熔后工件有压伤/破裂/毛边等制程不良defect with pit, crack, burr after heat stacking排线受损Flex Damage 组件排线外观有压伤/破损appears pit or damage on assembly flex surface卡钩干涉Hook interference 前盖卡钩组合回弹不顺畅flip not smoothly of hook assembly溢胶Glue Leak 背胶超出粘贴位置glue be adhibited to unwanted areas插头NG（PIN针不良）PIN Fault 插头歪斜或失效PIN appears deflection or ineffect轴紧Tight Hinge 转轴组件配合过紧，致回弹不顺畅hinge assembly too tight result in spring not smoothly轴松Loose Hinge 转轴组件配合过松，致回弹无节奏感hinge assembly too loose result in spring not rhythmic3.功能缺陷Function Defect主显示背光不良Main Backlight Luminance NG 开机状态主LCD背光亮度不合格main LCD backlight luminance is NG under power on副显示背光不良LCI Backlight Luminance NG 开机状态副LCD背光亮度不合格CLI Backlight Luminance is NG under power on音效不良Audio Defect 语音接听时有听到异常声音或者杂音abnormal sounds or cacophony will be heardLCD无法显示LCD no Display 开机后LCD无法显示正常画面LCD cant not display normally after power on显闪Flash 图像测试闪烁display flash when testing picture像素不良Pixel Fault 像素缺失超规pixel miss out of specification声音强度超规Speaker volume NG 喇叭的声音强度测试超出规格speaker level test out of specification声音损耗超规Speaker Distortion NG 喇叭的声音失真度测试超出规格speaker distortion test out of specificationLCD显示不正常LCD Display Abnormal 正常开关机时LCD显示黑线、亮紋、缺少像素,重影、画面歪斜等LCD display defect with blackline, light texture, lack image, double or deflection under power on or power off震动异常Vibration NG 手机震动有异常声音或者震动幅度频率异常等mobile phone appearing defect with abnormal sound and vibration frequency背光测试异常Backlight Test Fail LCD显示无背光，背光亮度异常，缺少像素等不良LCD display defect with no backlight ,abnormal brightness, lack image开合异常Opening and Closing of Flip NG 翻盖组件和前支撑座组件呈45°时翻盖无法自动闭合，或两组件呈90°时翻盖无法自动打开。
缺陷中英文对照
劃形狀 皮 薄的
裂片 細小
弄髒
布類玩具
沾污
焊錫 溶劑 穩定 編法
poor embroidery poor hair inter-lock stitching poor hair style poor heat sticking poor hot melting poor hot stamp poor hot stamping poor lock stitching poor booted hair poor sewing poor silk-screening poor sketching poor stitch poor stuffing pucker ribbon fray rough surface scratch mark screw burst screw came off screw rust screw unfasten seam allowance expose seam open sewing label loosen sewing machinery mark stitching hole stuffing disproportion stuffing expose/cotton expose stuffing expose the eyes can't move smoothly thread trapped by seam under glue uneven shape uneven stuffing untrimmed thread use unmatched swatches in one boll white powder on body velcro come off/magic tape come off velcro detach velcro position too hight/low water stain mark wrong assembly wrong/missing part
中英对照文产品不良
PART 1-1 PRODUCT AESTHETIC(产品外观）sratches,cracks,scuff marks,or dent visible from distance of 10mm on front housing浅花痕deep scratches,cracks,scuff marks,or dent visible from distance of 10mm on rear housing深花痕dirt or fingerprints erasable by using a cloth on front or rear housing面壳污或指印能用布清理scratch or dirt on lens,mirror,panel,button,or housing面镜，镜面框，按钮或机壳刮花或污deformed变型flash or burr area>2 X1mm水口或披风大于2 X1公分面积flow mark,or shrinkage worse than approval sample夹水纹及缩水比确认样办差plastic parts short shot塑料缺料破烂housing poor matching with gap>0.5mm机壳配合不良导致空隙大于0.5公分missing parts漏配件poor lens,panel or housing assembling镜面，壳框及机壳装配不良hinge loosen铰合部松hinge,crane or snap loose,broken or damaged塑料铰合部，扣位松脱或破损cover cannot be opened due to crane or snap too tight面盖扣位过紧不能打开battery compartment design not meet IEC battery standard size电池舱设计不符合ＩＥＣ标准battery shortcircuit due to battery compartment design电池位设计不良导致电池容易短路battery door too tight电池门太紧battery door loosen during normal use正常使用时电池门松脱battery door lock damaged电池门扣位破损battery door cannot assemble properly电池门不能正常安装rust on metal part金属部位生锈corrosion on metal part金属部位腐蚀氧化R/C cable cannot pull out遥控线拉不出PART-2 PAINT SPRAYING/SILK SCREEN PRITING喷油丝印printing illegible染丝印模糊missing print or spraying丝印或喷油漏poor wood texture coating,painting or silk screening丝印喷油或木纹不良color deviation slightly per approval sample颜色色差与确认样办少许不符color fading as per approval sample颜色褪色与确认样办不符contamingation or uneven color priting.painting丝印,喷油有污迹或颜色不均匀PART-3 METAL五金screw unfasten螺丝未上紧screw misalignment螺丝歪斜miss 1 screw on housing but no gap was found机壳螺丝遗漏一粒而没导致离壳battery door can not open电池门不能打开screw loosen on husing机壳螺丝松脱rust on screw螺丝生锈screw came off 螺丝脱落screw to be stripped螺丝滑牙dirt or scratch surface金属表面刮花或污渍deep scratch on surface金属表面深刮花痕battery plate deformed电池片变形battery plate poor contact电池片接触不良wromg battery plate size电池片长度不符short circuit if battery assemble reversed电池装反时短路metal burr金属披锋burr on plating电镀有毛刺plating peel off电镀脱落poor metal electro plating电镀不良bad contact when used duracell/energizer battery使用金霸王／劲量电池不通电battery plate oxidization弹簧氧化PART-4 SOCKET插座socket loose or not secured插座松或不稳固socket short circuit插座内部短路connector or jack cannot plug-in or loosen插座或孔过紧或过松PART-5 liquid crystal display/LED product液晶显示/发光二极管产品wrong display液晶显示错误dim segment or uneven brightness液晶显示暗或光暗不均匀segment blurred显示模糊missing/short segment or dot displayed液晶显示缺划，漏点或短路shade on display显示有重影purple spot caused by pressure液晶曾受压呈紫色contamination inside污物在液晶显示内finger print or dirt on display有污渍或手指模印misalignment and excess of the viewing area on panel液晶外露黑边excessive dot on LCD display液晶显示有黑点LED dead发光二极管坏LED dim发光二极管暗light spot misalignment发光点移位LED dislocated发光二极管安装不良solar battery no function太阳能没有功能no charging function没有充电功能cord cannot return拉线不能回收LED cannot off LED 不能关power no function使用电源没有功能PART-6 SOUND 声音sound distortion声音失真weak sound level声音输出弱buzz,noise or howling蜂鸣片有杂声或共呜声sound oscillation,intermittent声音起振或间歇发声volume level not in"hi"level as required声音没有按要求选择到最大PART-7 外物foreign materialconductive/nonconductive inside unit 机内有电导性/非电导性外物wire exposure电线外露foreign material on unit机身有外物excessive tape mirror or lens胶纸有外物待续。
主要缺陷中英文对照
主要缺陷中英文对照————————————————————————————————作者：————————————————————————————————日期：2德仕科技（深圳）有限公司品管部中英文对照表（一）主要缺陷中英文对照序号中文英文序号中文英文1 披峰Flash 16 流痕Flow mark2 走不齐/缺胶Short shot 17 色差 abberration3 变形/注塑后变形Deformation 18 夹水线Weld lines4 偏模Mismatch 19 碰伤Bump damage5 起泡Blister 20 银线Silver6 污斑Grease pits 21 少数量Packing shortage7 雾化Atomization 22 泛白Blushing8 烧焦Burn mark 23 发白Whitening9 油污Oil mark 24 刮伤Scratch10 气泡Blister 25 气纹Gas lines11 划痕Scffing 26 混色Color mixture12 泛黄Yellowing 27 斑点/污点/ 黑点Macula13 缩水Sink mark 28 结合线14 段差29 拉伤Pull15 抛光不良Polishing mark 30 水印Watermark主要测量仪器中英文对照序号中文英文序号中文英文1 分厘卡(千分尺)Micrometer 14 卡尺Caliper2 C表Dial gauge 15 扁分厘卡Blade micrometer3 块规Block gauge 16 针规Pin gauge4 CMM X-Y-Z Coordinate 17 电子卡尺Digital caliper5 扭力计Torque meter 18 投影仪Projection apparatus6 高度仪Height gauge 19 直角尺Square master7 游标卡尺Vernier caliper 20 硬度机Durometer8 牙规Scre gauge 21 半径规Radius gauge9 角度规Universalprotractor22 特别塞规Ring gauge10 拉/推力计Pull/Push gauge 23 弹力计Spring balance11 塞尺Clearance gauge 24 专用夹具Special fixture12 工具显微镜Tool-measuringmicroscope25 千分表Dial indicator131 抽样Sampling 11抽样计划Samplingplan2 样品数量Sample size 12 合格Conformity3 批量lot size 13 缺陷Defect4 目测Eyeballing 14 让步Concession5 外观Appearance 15 检验Inspection6 测量Measurement 16 规范Specification7 质量Quality 17 报废Scrap8 接收Acceptance 18 纠正Correction9 不良品Defectiveproducts1910 返工Rework 20。
产品缺陷名词中英文对照表
中文 缺劃 混周期 混機種 露銅線 無鋁線
Band 電鍍不良 PIN 彎 Bend Pin 氣泡(氣洞) Bubble Cont /Contamination in paint 油墨髒污 Cleaning water consists Cu10 水洗含銅粉 power 11 Cold soldering joint 假焊 12 Conformal Coating 13 Cross talk 14 Dim/Segment Dim 15 Display NG 16 Dice Bonding fails 17 Dice damaged 18 Dice peeling off 19 Dice position incorrect/Dice mis-alignment 20 Dirty on solering pad 21 Dot-spot/Hot-spot 22 Electrode oxidation 23 Electrode damaged 24 Epoxy crack 25 Epoxy on PIN 26 27 28 29
PIN沾膠 70 表面沾膠 71 側面爬膠(沾膠 72 多膠(溢膠) 73 少膠 74
Epoxy on surface Epoxy on wall Epoxy overfill Epoxy QTY low /Epoxy underfill 30 Electromigration(Micro 微短路 PCB短路 75 Short circuit on PCB short circuit) 銀膠短路 76 Poor silk screen 絲印不良 31 Epoxy caused short circuit 銀膠浮起 77 Sop sponge wheel adhere Cu-power 吸水海棉轆沾有銅粉 32 Epoxy floating up 33 Foreign material /object /body異物 78 Solder Bridge 連錫 34 Fiberglass uneven 纖維布不均 79 The durability of epoxy is insufficient 銀膠膠力不夠 第一焊點脫落 Uneven brightness 80 亮度不均 35 First stitch peeling off 36 High Vf 正向壓降高 81 Uneven color 顏色不均 37 Highly viscosity/highly chance 太粘/很大可能 82 Highly toxic gase/highly suspect 巨毒氣體/很懷疑 IC管孌形 83 Void 白點 38 IC tube warpage 39 Inner carton&shipping box 內外包裝箱 84 Water cleaning insufficient 水洗不充分 40 INT 不穩定 85 Warp/Transform 孌形 41 IR/Reverse current 反向電流 86 White(Green) masking 白(綠)油 光強 打不上線 42 IV 87 Wire Bonding fails 泄光 88 Wrong bin grade 亮度等級錯 43 Light leakage 背光板不良 89 Wrong dice 用錯晶片 44 Back Light board failure 45 Marking permancy 印章永久性 89 Wrong label 標簽錯 46 Marking out of position 印章位置錯 90 Wrong mark 印章錯 Missing dice 46 91 Wrong pole and bining cop 極性與等級印章錯 漏上晶片 可以表示不良的英文詞有:failure,defect,poor,imperfect,fault,flaw,weak,insufficent,not well,problem,,shortcoming, Failure:含义包括，失败、失效、故障、事故、中断、损坏、折断、衰退、缺少、不足等 prepared by: Patrick Chu Confirmed by: Donald Mok
产品缺陷名词中英文对照表
串劃 字劃孌暗 顯示不通過 DB不良 晶片損傷 晶片脫落 晶片偏位 焊盤髒 背光源 電極氧化 電極破損 銀膠裂開
64 Reflector press on the dice 65 Sagging wire 66 Soldering broken 67 Solder risidual caused short circuit 68 Solder risidual on PCB 69 Row-thread broken Scratched on Reflector Seep segment(1/3 Segment) Short circuit Second stitch peeling off Bur
防水油
混機種與等級 節死 開路(斷路) Opening of Row-thread exposed metal wire 排線開口處露金屬線 外形尺寸 數量短少 蝕刻過度 上 弧倒 爛焊 錫渣短路 PCB上有錫渣 排線爛 反射蓋劃傷 字劃滲透(1/3字劃) 短路 第二焊點脫落 批峰
產品缺陷名詞中英文對照表
項目
Update date:Aug,30,2006
1 2 3 4 5 6 7 8 9
英文 Poor adhesive force Aluminium-wire broken Basic(Raw) material failure Poor plating Bur
中文 粘力差(膠紙 鋁線爛 基材不良 電鍍不良 毛刺
Epoxy on surface Epoxy on wall Epoxy overfill Epoxy QTY low /Epoxy underfill 30 Electromigration(Micro 微短路 PCB短路 75 Short circuit on PCB short circuit) 銀膠短路 76 Poor silk screen 絲印不良 31 Epoxy caused short circuit 銀膠浮起 77 Sop sponge wheel adhere Cu-power 吸水海棉轆沾有銅粉 32 Epoxy floating up 33 Foreign material /object /body異物 78 Solder Bridge 連錫 34 Fiberglass uneven 纖維布不均 79 The durability of epoxy is insufficient 銀膠膠力不夠 第一焊點脫落 Uneven brightness 80 亮度不均 35 First stitch peeling off 36 High Vf 正向壓降高 81 Uneven color 顏色不均 37 Highly viscosity/highly chance 太粘/很大可能 82 Highly toxic gase/highly suspect 巨毒氣體/很懷疑 IC管孌形 83 Void 白點 38 IC tube warpage 39 Inner carton&shipping box 內外包裝箱 84 Water cleaning insufficient 水洗不充分 40 INT 不穩定 85 Warp/Transform 孌形 41 IR/Reverse current 反向電流 86 White(Green) masking 白(綠)油 光強 打不上線 42 IV 87 Wire Bonding fails 泄光 88 Wrong bin grade 亮度等級錯 43 Light leakage 背光板不良 89 Wrong dice 用錯晶片 44 Back Light board failure 45 Marking permancy 印章永久性 89 Wrong label 標簽錯 46 Marking out of position 印章位置錯 90 Wrong mark 印章錯 Missing dice 46 91 Wrong pole and bining cop 極性與等級印章錯 漏上晶片 可以表示不良的英文詞有:failure,defect,poor,imperfect,fault,flaw,weak,insufficent,not well,problem,,shortcoming, Failure:含义包括，失败、失效、故障、事故、中断、损坏、折断、衰退、缺少、不足等 prepared by: Patrick Chu Confirmed by: Donald Mok
不良缺陷中英文对照
19 20 21 22 23 24 25
铭牌同边框平行度 接线盒到长边框外侧距离 接线盒到短边框外侧距离 边框条码位置 长边框外凸 长边框内凹 焊带扭曲
英文
Cell to Glass edge Parallel Difference (Laminator) Big side string bus to glass edge Parallel Difference (big side string bus to glass edge) Small side string bus to glass edge Parallel Difference (small side string bus to glass edge) Cell to frame edge Parallel Difference (Module) Big side outer strings bus to frame distance Parallel Difference (Module) Big side outer strings bus to cell distance Big side inner strings bus to cell distance Small side strings bus to frame String distance Cell to cell offset in difference string Parallel Difference (from first to last cell) Label postion to long frame Label postion to long frame
44 45 46 47 48 49 50
ቤተ መጻሕፍቲ ባይዱ
cell connector offset
质量缺陷中英对照
质量缺陷中英对照1.MISSING …………….缺少…………… , 掉了……………例句:--- MISSING COMPONENTS 缺部件--- MISSING PARTS 缺零件--- MISSING MANUAL 缺操作说明--- MISSING INSTRUCTION LEAFLET 缺说明书--- MISSING BROCHURE 缺简介小册--- MISSING LABEL 缺标签--- MISSING STICKER 缺贴纸--- MISSING BAR CODE 缺条形码--- MISSING ASSEMBLE SHEET 缺组装说明--- MISSING 3/16” SLOTTED BIT 缺3/16” 一字起子头--- MISSING 10 MM DEEP SOCKET 缺10 MM 长套筒2. N. (V + ING ) OF……. PARTS ( 或ON ……… SURFACE )例句:--- PITTING OF METAL PARTS 金属零件凹陷--- FLAKING OF CHROME PLATING 镀铬层剥脱壳--- FLASHING OF PLASTIC PARTS 塑料零件毛边--- FAILURE ON COATING SURFACE 烤漆表面不合格--- DEFORMATION OF RACK 框架变形--- MOULDING OF WOODEN HANDLE 木柄发霉--- CHIPPING ON STEEL PIPE SURFACE 铁管表面裂伤--- CRACKING OF 13 MM SOCKET13 MM 套筒裂痕--- DENT ON METAL PLATE SURFACE 金属板表面凹痕--- NICK OF PLASTIC CASE 塑料盒割痕)--- DUST OF PACKAGE 包装尘污--- RUSTING ON PLATING SURFACE 电镀表面生锈--- SMUTTING OF ARTWORK 彩卡脏污!--- SCRATCHING ON COATING SURFACE 烤漆表面刮伤--- SHARP EDGE OF HANDLE 手柄锐边--- CORROSION ON METAL SURFACE 金属表面腐蚀--- PEELING OF CHROME PLATING 镀铬层剥落--- BURRS OF GRINDING EDGE 研磨端毛边3. POOR + N. ( V + ING ) OF ……… 不良的……. , 太差的…….例句:--- POOR MARKING OF LOGO 商标印字不良--- POOR LABELING OF STICKER 贴纸黏贴不良--- POOR COATING OF FRAME 支架烤漆不良.--- POOR MOLDING OF PLASTIC HANDLE 塑料手柄成型不良--- POOR RIVETING OF PLATE CONNECTION 平板铆接不良--- POOR FORMING OF SHELF 棚架成型不良--- POOR PLATING 电镀不良--- POOR CLEANING 清洁不良--- POOR PRINTING 印刷不良--- POOR GLUING 胶合不良--- POOR ASSEMBLING组装不良--- POOR JOINT 接合不良--- POOR BALANCE 平衡不良--- POOR LASER MARK雷射不良--- POOR SHAVING 车削不良--- POOR EMBOSSING 滚花不良--- POOR PACKAGING 包装不良4. …… NOT MEAT…… , …… OUTSIDE ……. ,…… NOT MATCH …….……..不符合……. 例句:--- CONTENTS NOT MATCH P/O内容物不符订单--- OVERALL LENGTH NOT MEAT SPEC总长度不符规格--- HARDNESS OUTSIDE STANDARD硬度不符标准--- PRODUCTS NOT MATCH SEALED SAMPLE产品不符确认样品--- PACKAGE NOT MEAT P/O包装不符订--- FUNCTION NOT MEAT REQUIREMENT 功能不符需求5. ……… FAILED , ………. 不合格例句:--- IMPACT TEST FAILED 冲击测试不合格--- GO / NO GO GAGE FAILED 塞规测试不合格--- TORQUE TEST FAILED 扭力测试不合格--- HARDNESS TEST FAILED 硬度测试--- DROP TEST FAILED 落地测试不合格--- PERMNENT TEST FAILED 变形测试不合格--- WIRE CUTTING TEST FAILED 剪钢线测试不合格--- BENDING TEST FAILED 弯折测试不合格--- STRENGTH TEST FAILED 张力测试不合格--- STRIKING TEST FAILED 敲击测试不合格。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
指示管彈起
Water level tube out the position
MI
保溫瓶蓋漏裝單向閥
Missing valve of carafe cover
MA
保溫瓶蓋漏裝密封圈
Missing seal ring on carafe cover
MA
水箱入水口波珠不動
Quiescent ball of water inlet
Missing marking on carton
MA
漏貼電壓貼紙
Missing rating label
MA
電線燙傷表皮
Damaged power cord
MI
頂蓋內有雜物
Foreign object inside lid
MA
用錯面包桶
Wrong bake pan
MA
纖維線露出窗外
Fiber wire out the shutter on housing
MI
水箱縮水和气紋
Shrinkage and flow mark on tank
MI
底座爆裂
Cracked base
MA
底座刮花及黑點
Scratch and black spot on base
MI
水箱与底座顏色不同
Color mismatch between tank and base
MI
指示管膠塞漏水
MI
漏斗軸漏裝膠塞
Missing plug on basket axes
Ma
保溫板密封圈未裝到位
Keep warming plate seal ring out the position
Ma
底蓋隔熱板氧化
Oxidate mark on bottom cover
Ma
水箱与底蓋夾有膠紙
Protective paper clamped between tank and base
MA
壺蓋阻流器松動
Loose stopper of carafe cover
MA
線套爛
Damaged power supply cord bushing
MA
面包机
發熱管污跡
Dirty on heater
MI
底座与外殼錯位
Step between housing and bottom cover
MI
卡通箱漏印字嘜
Step between base and bottom cover
MI
玻璃杯爛
Damaged carafe
MA
玻璃杯崩口
Broken edge of carafe
MA
玻璃杯花和有泡點
Scratch and blister on carafe
MI
入水管未裝到位
Input water tube out the position
MA
頂蓋黑點
Black spot on lid
MI
控制蓋混色
Mixed color on control panel cover
MI
插頭不洁和花
Scratch and dirty on the power plug
MI
攪粉時摩打不轉
No rotation while kneading dough
MA
Baking pan loose or tight
MI
內箱氧化
Oxidate on baking cavity
MI
開机INT
Power interruption
MA
插頭崩裂
Broken plug of cord
MA
攪粉面包桶彈起
Baking pan pop out while kneading dough
MA
面貼翹起
Control panel label lifting
MI
顯示缺划
LCD display miss segment
MA
漏裝膠腳
Missing rubber foot
MA
開机顯示”ES”
Malfunction with "ES" on LCD while energization
MA
桶緊及桶松
MI
指示管絲印不良
Poor silk-screen on water level tube
MI
漏斗絲印花
Poor silk-screen on basket
MI
指示管漏絲印
Water level tube missing silk-screen
MA
電線不洁
Dirty on power supply cord
MI
LCD內有污物
Dirty in the LCD window
MI
控制蓋刮花
Scratch on Control panel cover
MI
控制蓋邊批損
Scratch on edge of control panel cover
MI
按鍵手感不良
Poor touching on button
MI
LCD鏡片裝配不正
MA
前頂蓋變形
Deformed front cabinet cover
MA
指示管浮球披峰
Flashing on indicative ball
MI
干煲燒FUSE
Thermofuse burn off as dry heating
MA
開關制偏緊
Power switch stiff
MI
開關接触不良
Power switch interrupted
摩打不轉
Motor not rotation
MA
電線偏短
Short power cord
MA
控制蓋与外殼顏色不一致
Color mismatch between control panel cover and metal housing
MI
外殼麻點
Blister on metal housing
MI
摩打与發熱管同時工作
MA
燈不亮
Indicator lamp on switch not lit up
MA
漏裝膠腳
Missing rubber foot
MA
膠腳不平
Rocking on rubber foot
MI
漏放說明書
Missing instruction book
MA
絲印刮花
Scratch on silk-screen
Leaking on plug of water indicator
MA
漏裝浮球
Missing water indicative ball
MA
保溫瓶內有雜物(玻璃碎)
Foreign object inside carafe(A fragment of glass)
MA
杯蓋單向閥披峰
Flashing on valve of carafe cover
MI
前頂蓋未扣到位
Front cabinet cover unlatched
MI
前頂蓋刮花
Scratch on front cabinet cover
MI
前頂蓋爆裂
Cracked front cabinet cover
MA
前頂蓋与水管离位
Gap between front cabinet cover and tank
LCD display screen misalign met with the window of control cover
MI
外殼有絲印油
Paint on metal housing
MI
玻璃窗花及污跡
Scratch and dirty on glass of lid
MI
開机無“B”聲
No buzzing
MI
入水管漏水
Leaking on input water tube
MA
漏斗不能止水
No drip stop on filter basket
MA
漏斗披峰
Flashing on filter cone
MI
底座与底蓋离拉
Gap between base and bottom cover
MI
底座与底蓋錯位
MA
保溫杯內雜物
Foreign object inside carafe
MA
漏裝漏斗插針孔膠塞
Missing the plug of pin hole of basket
MA
玻璃杯邊刮手
Sharp edge on carafe
CR/MA
漏斗內有披峰堵塞
Flashing block the outlet of basket
LCD display unclear
MI
面貼未撕保鮮紙
Protective paper on indicated label
MI
"B"聲小
Insufficient buzzing
MA
百葉窗變形
Distortion persiennes
MI
卡通箱一面漏編總箱號
No total-carton-no. on one side of the carton
MA
杯柄不正
Spout of carafe misalignment with handle
MI
后頂蓋与水箱离拉
Gap between tank and tank cover