MSP430g2553原理图

合集下载

MSP430 g2553,中文资料

引导加载器 (BSL)
嵌入式仿真模
块 (EEM)
1
1
1
1
1
1
1
1
1
1
表 1. 提供的选项(1)(2) (接下页)
ZHCS178E – APRIL 2011 – REVISED JANUARY 2012
闪存 (KB)
RAM (B)
Timer_A
COMP_A+ 通道
10 通道 ADC
USCI A0/B0
P2.0/TA1.0 8 P2.1/TA1.1 9 P2.2/TA1.1 10
N20 PW20 (TOP VIEW)
20 DVSS 19 XIN/P2.6/TA0.1 18 XOUT/P2.7 17 TEST/SBWTCK 16 RST/NMI/SBWTDIO 15 P1.7/CAOUT/UCB0SIMO/UCB0SDA/A7/CA7/TDO/TDI 14 P1.6/TA0.1/UCB0SOMI/UCB0SCL/A6/CA6/TDI/TCLK 13 P2.5/TA1.2 12 P2.4/TA1.2 11 P2.3/TA1.0
28 引脚 24 TSSOP 封
装
20 引脚 16 TSSOP 封
装
16
20 引脚 PDIP 封装
24
32 引脚 QFN 封装
28 引脚 24 TSSOP 封
装
20 引脚 16 TSSOP 封
装
16
20 引脚 PDIP 封装
24
32 引脚 QFN 封装
28 引脚 24 TSSOP 封
装
20 引脚 16 TSSOP 封
• 通用串行通信接口 (USCI) – 支持自动波特率检测的增强型通用异步收发器 (UART) – IrDA 编码器和解码器 – 同步 SPI – I2C™

基于MSP430g2553的心形呼吸流水灯

430注意！在画原理图的时候，需留出一个跳线接口，在编程调试的时候要将复位电路与 430 电路的连接断开（ C3 电容会对编程调试时的数据传输产生影响）。另一个解决办法是：去掉 C3 电容，在复位电路与 430 电路之间加一个 2K 的电阻。
如图所示
锁存器和 LED
breath_down(500,0x01,0xFF); breath_up(500,0xFF,0xFF); delayms(500); breath_down(500,0xFF,0xFF); P1OUT=0x00; P2OUT=0x00; delayms(500); flicker(0x8E,0xE3,6,100); 闪烁“笑脸” for(i=4;i>0;i--) //呼吸 { breath_up(1000,0xFF,0xFF); delayms(500); breath_down(1000,0xFF,0xFF); } P2OUT=0x80; P1OUT=0x00; delayms(500); P2OUT=0x40; P1OUT=0x00; delayms(500); while(1) //两个 LED“永无止境的追逐” { run_two(1); } } }
Made by Wonder 由于能力有限，如有错误，请多多包涵！如有更好的方案，wondertmac@，欢迎来件交流。
基于 MSP430g2553 的心形呼吸流水灯
简述：
这个电路主要由： MSP430g2553 单片机（28PIN、 TSSOP 封装）、 74HC573 锁存器（20PIN、SOIC 封装）、TLV117 稳压组成。主要原理是利用 430 单片机产生 PWM 信号，通过 573 的使能控制一定数量的 LED 产生同节奏的 “呼吸” 效果。通过对产生 PWM 信号的寄存器的设置，可以得到程度不同的 “呼吸”效果。话不多说，先上原理图。

程控运算放大模块实验指导书

一、实验目的1. 熟悉Launchpad 开发板的使用方法2. 学习MSP430G2553单片机内部ADC10和定时器的使用方法。

3. 学习使用PGA112芯片4. 学习使用12864液晶显示5. 提升动手能力和独立思考问题的能力二、实验设备和工具Launchpad 开发板、程控运算放大器实验模块、万用表、MSP430实验底板、12864液晶、CCS 开发工具等三、实验原理该实验的总体设计框图如下图1 程控运算放大模块整体设计框图可简单概括为：将3.3V 电源电压通过稳压芯片LM385稳压到2.5V ，再通过电阻分压获得一个十几mV 的电压接到程控运算放大芯片PGA112的输入端口，该芯片通过与单片机进行SPI 通信，对输入信号进行不同的放大（由拨码开关或按键控制放大倍数），将放大后的信号输入给单片机，通过单片机的ADC 对放大信号进行采样，最后将采样值转化为实际值并在液晶上实时显示。

1. MSP430G2553 图2是单片机MSP430G2553引出管脚原理图，它的部分引脚与PGA112进行SPI 通信，部分与液晶连接，将PGA112的输出作为单片机的输入对其AD 采样，将采样值转化为测量值并通过液晶实现对测量值的实时显示。

图2 msp430g2553引出管脚原理图1.ADC10和定时器ADC10 是MSP430单片机的片上模数转换器，根据其命名大家知道转换位数为10比特。

ADC10的最大转换速率大于200kHz ，转换精度为10位，其转换时钟源可选择，利用软件或者TimerA 设置转换初始化，编程选择片上电压参考源（2.5V 或者1.5V ）。

在MSP430 的ADC10上有12个通道，其中8 个外部输入通道，具备对内部温度传感器（通道10）、供电电压VCC 和外部参考源的转换通道。

ADC10有多种采样模式，分别为单通道采样、重复单通道采样、顺序采样和重复顺序采样。

本实验ADC10设置成多次连续采样模式，基准电压2.5V，ADC10开中断，ADC10SC触发采集，采集通道0。

MSP430g2553课件

（演示）
南京航空航天大学电子中心&TI南航430联合实验室
如何改变发光二级管闪烁的速度？

改变延时的时间参数

1、亮 2、延时1秒钟 3、熄灭 4、延时1秒钟 5、跳转到步骤1

（演示）
南京航空航天大学电子中心&TI南航430联合实验室
如何让一只发光管闪快、另一只慢？

增加一个变量xx

南京航空航天大学电子中心&TI南航430联合实验室
MSP430单片机学习方法
强化理论知识大量做实验勤于思考多动手

已经与MSP430厂家———TI（德州仪器）建立了联合实验室，拥有60套实验设备。地点：3410。其中40套为赠送，20套购买
南京航空航天大学电子中心&TI南航430联合实验室
while(条件表达式) 语句；当条件满足时，就反复执行后面的语句，一直执行到条件不满足时。以软件延时程序为例说明该语句是如何执行的。 void delay(long v) { while(v!=0)v--; }

南京航空航天大学电子中心&TI南航430联合实验室

P1
P2
P3 P4
P5 P6
南京航空航天大学电子中心&TI南航430联合实验室
引脚控制寄存器

PnDIR PnOUT PnIN PnSEL
方向寄存器 1为输出、0为输入输出寄存器 1输出高、0为低输入寄存器读出口线的状态第二功能寄存器 n=1,2,3,4,5,6
南京航空航天大学电子中心&TI南航430联合实验室
南京航空航天大学电子中心&TI南航430联合实验室

msp430g2553多路数据采集器

基于MSP430G2553的多路数据采集班级:科技1201班姓名：石思恩学号：05122015日期：2014/12/10一．实验题目：基于msp430G2553的多路数据采集。

二．实验目的：8通道精密模拟量数据采集器采集8路模拟量输入信号。

任一时刻，多路模拟开关选择其中一路输入信号，该信号通过信号调理电路调理后，送入AD转换器转换成数字量，该数字量在lcd12864显示。

三．实验内容：1.实验原理：在本数据采集系统的设计中为了提高系统智能化、可靠性和实用性，采用单片MCU和上位机传输的方法，即MCU运行在数据采集系统的远端，完成数据的采集、处理、发送和显示，上位机则完成数据的接收、校验及显示，同时上位机可对远端MCU进行控制，使其采集方式可选。

MCU选用TI公司的低功耗MSP430G2553，该单片机比80C51功能要强大许多，他内部不仅有8路12位A／D，而且还带LCD的驱动，节省了不少外围电路。

本系统采用信号发生器产生正弦波，然后由LM358芯片实现对电压的放大，之间还需对信号进行调理以符合系统要求。

2.实验步骤：1.实验系统框图：2.放大电路：3.源程序：#include <MSP430G2553.h>#define uchar unsigned char#define uint unsigned int#define cs_1 P2OUT|=BIT5#define cs_0 P2OUT&=~BIT5#define sid_1 P2OUT|=BIT3#define sid_0 P2OUT&=~BIT3#define en_1 P2OUT|=BIT4#define en_0 P2OUT&=~BIT4uchar num1[8], a[5],m[5],n[5];double result[4],AD_result[4];int position=0;int status=0;int flag=0;int jiaquan=0;float sample;void delayr(void);void delays(void);void adc10_begin();void adc10_ceshi();void temar_ceshi();void adc10_ceshi1();void adc10_ceshi2();const uchar line1[]={"电压为V"};const uchar line2[]={"电压为V"};const uchar line3[]={"电压为V"};const uchar line4[]={"电压为V"};void IO_Init(void){P2SEL=0x00;// 2553将其初始化为晶振输入端，所以要关掉第二功能选择P2DIR|=0xff;//将其置为输出方向P2OUT=0x00;//输出0}void delay(uint x){uint i,j;for(i=0;i<x;i++)for(j=0;j<100;j++);}void write_cmd(uchar command_data){uchar i;uchar i_data;i_data=0xf8;cs_1;en_0;for(i=0;i<8;i++){if(i_data & 0x80)sid_1;elsesid_0;en_0;en_1;i_data<<=1;}i_data=command_data;i_data&=0xf0;for(i=0;i<8;i++)if(i_data & 0x80)sid_1;elsesid_0;en_0;en_1;i_data<<=1;}i_data=command_data;i_data<<=4;for(i=0;i<8;i++){if(i_data & 0x80)sid_1;elsesid_0;en_0;en_1;i_data<<=1;}cs_0;delay(10);}void write_data(uchar command_data) {uchar i;uchar i_data;i_data=0xfa;cs_1;en_0;for(i=0;i<8;i++){if(i_data & 0x80)sid_1;elsesid_0;en_0;en_1;i_data<<=1;}i_data=command_data;i_data&=0xf0;for(i=0;i<8;i++)if(i_data & 0x80)sid_1;elsesid_0;en_0;en_1;i_data<<=1;}i_data=command_data;i_data<<=4;for(i=0;i<8;i++){if(i_data & 0x80)sid_1;elsesid_0;en_0;en_1;i_data<<=1;}cs_0;delay(10);}void LCD_Init (void){delay(10);write_cmd(0x30);delay(10);write_cmd(0x0c);delay(10);write_cmd(0x01);delay(5);}void LCD_pos(unsigned char X,unsigned char Y) {unsigned char pos;if(X==0)X = 0x80;else if(X==1)X = 0x90;else if(X==2)X = 0x88;else if(X==3)X = 0x98;pos = X + Y;write_cmd(pos);}void Display_Init (void) {unsigned char i;LCD_pos(0,0);i=0;while(line1[i]!= '\0') {write_data(line1[i]);i++;}LCD_pos(1,0);i=0;while(line2[i]!= '\0') {write_data(line2[i]);i++;}LCD_pos(2,0);i=0;while(line3[i]!= '\0') {write_data(line3[i]);i++;}LCD_pos(3,0);i=0;while(line4[i]!= '\0') {write_data(line4[i]);i++;}}void ADC10_init(){WDTCTL = WDTPW + WDTHOLD; // Stop WDTP2SEL=0x00;P2DIR |= 0xff; // Set P1.0 to output directionP1DIR |= 0x38;P1SEL|=BIT0+BIT1+BIT2;ADC10AE0|=BIT0+BIT1+BIT2+BIT5; // 使P1.0允许AD模拟输入信号ADC10CTL0=ADC10ON+MSC+SREF_0;//+REFON 开AD内核，选择电源为参考电压ADC10CTL1=ADC10SSEL_0+CONSEQ_0; //+INCH_1+INCH_2 选择ADC12SC为触发源,选择系统时钟为AD内核时钟，采用单通道多次采用}void adc10_begin(void){ADC10CTL1|=INCH_0;ADC10CTL0|=ADC10SC+ENC; // 开始转换开转换允许while(ADC10CTL1&ADC10BUSY!=0);//判断是否转换完毕result[0]= ADC10MEM;AD_result[0]=(result[0]/1024)*3.485;ADC10CTL0&=~(ADC10SC+ENC); //关转换允许才能选择通道ADC10CTL1&=~INCH_0; //通道清0ADC10CTL1|=INCH_1;ADC10CTL0|=ADC10SC+ENC;while(ADC10CTL1&ADC10BUSY!=0);result[1]= ADC10MEM;AD_result[1]=(result[1]/1024)*3.485;ADC10CTL0&=~(ADC10SC+ENC);ADC10CTL1&=~INCH_1;ADC10CTL1|=INCH_2;ADC10CTL0|=ADC10SC+ENC;while(ADC10CTL1&ADC10BUSY!=0);result[2]= ADC10MEM;AD_result[2]=(result[2]/1024)*3.485;ADC10CTL0&=~(ADC10SC+ENC);ADC10CTL1&=~INCH_2;ADC10CTL1|=INCH_5;ADC10CTL0|=ADC10SC+ENC; // 开始转换开转换允许while(ADC10CTL1&ADC10BUSY!=0);//判断是否转换完毕result[3]= ADC10MEM;AD_result[3]=(result[3]/1024)*3.485;ADC10CTL0&=~(ADC10SC+ENC); //关转换允许才能选择通道ADC10CTL1&=~INCH_5; //通道清0}void adc10_ceshi(void){uchar p,q,e;ADC10_init();adc10_begin();a[0]=(int)AD_result[0];a[1]=a[0]%10;a[2]=(int)((AD_result[0]-a[0])*10);a[3]=(int)(AD_result[0]*100)%10;a[4]=(int)(AD_result[0]*1000)%10;LCD_pos(0,5);for(p=0;p<4;p++){write_data(a[p]);}delay(2000);m[0]=(int)AD_result[1];m[1]=m[0]%10;m[2]=(int)((AD_result[1]-m[0])*10);m[3]=(int)(AD_result[1]*100)%10;m[4]=(int)(AD_result[1]*1000)%10;LCD_pos(1,5);for(e=0;e<4;e++){write_data(m[p]);}delay(2000);n[0]=(int)AD_result[2];n[1]=n[0]%10;n[2]=(int)((AD_result[2]-n[0])*10);n[3]=(int)(AD_result[2]*100)%10;n[4]=(int)(AD_result[2]*1000)%10;LCD_pos(2,5);for(q=0;q<4;q++){write_data(n[p]);}delay(2000);}void main(){WDTCTL = WDTPW+WDTHOLD;//关闭看门狗IO_Init();LCD_Init();Display_Init();//对LCD进行初始化，设置一个开机初始化显示_EINT();while(1){temar_ceshi();delay(1000);ADC10CTL0&=~(ADC10SC+ENC); //关转换允许才能选择通道ADC10CTL1&=~INCH_0; //通道清0adc10_ceshi();delay(1000);ADC10CTL0&=~(ADC10SC+ENC); //关转换允许才能选择通道ADC10CTL1&=~INCH_1; //通道清0temar_ceshi1();delay(1000);ADC10CTL0&=~(ADC10SC+ENC); //关转换允许才能选择通道ADC10CTL1&=~INCH_2; //通道清0adc10_ceshi1();delay(1000);ADC10CTL0&=~(ADC10SC+ENC); //关转换允许才能选择通道ADC10CTL1&=~INCH_3; //通道清0 }}void delayr(void){unsigned long data_delay;for(data_delay=0;data_delay<100000;data_delay++){}}void delays(void){unsigned long data_delay;for(data_delay=0;data_delay<167935;data_delay++){}}#pragma vector=TIMER0_A1_VECTOR__interrupt void TIMER0_A1(void){TACTL &= ~TAIFG;jiaquan++;}四、试验运行结果：五、实验中遇到的问题及解决方法：1.测试时不能实现多路采集，只能采一组。

MSP430G2553学习笔记(数据手册)概要

MSP430G2553学习笔记（数据手册）MSP430G2553性能参数(DIP-20) 工作电压范围：1.8~3.6V。

5种低功耗模式。

16位的RISC结构，62.5ns指令周期。

超低功耗：运行模式-230µA；待机模式-0.5µA；关闭模式-0.1µA；可以在不到1µs的时间里超快速地从待机模式唤醒。

基本时钟模块配置：具有四种校准频率并高达16MHz的内部频率；内部超低功耗LF振荡器；32.768KHz晶体；外部数字时钟源。

两个16 位Timer_A，分别具有三个捕获/比较寄存器。

用于模拟信号比较功能或者斜率模数(A/D)转换的片载比较器。

带内部基准、采样与保持以及自动扫描功能的10位200-ksps 模数(A/D)转换器。

16KB闪存，512B的RAM。

16个I/O口。

注意：MSP430G2553无P3口！MSP430G2553的时钟基本时钟系统的寄存器DCOCTL-DCO控制寄存器DCOxDCO频率选择控制1MODxDCO频率校正选择，通常令MODx=0注意：在MSP430G2553上电复位后，默认RSEL=7，DCO=3，通过数据手册查得DCO频率大概在0.8~1.5MHz之间。

BCSCTL1-基本时钟控制寄存器1XT2OFF不用管，因为MSP430G2553内部没有XT2提供的HF时钟XTS不用管，默认复位后的0值即可DIV Ax设置ACLK的分频数00 /101 /210 /411 /8RSELxDCO频率选择控制2BCSCTL2-基本时钟控制寄存器2SELMxMCLK的选择控制位00 DCOCLK01 DCOCLK10 LFXT1CLK或者VLOCLK11 LFXT1CLK或者VLOCLK DIVMx设置MCLK的分频数00 /101 /210 /411 /8SELSSMCLK的选择控制位0 DCOCLK1 LFXT1CLK或者VLOCLK DIVSx设置SMCLK的分频数00 /101 /210 /411 /8DCORDCO直流发生电阻选择，此位一般设00 内部电阻1 外部电阻BCSCTL3-基本时钟控制寄存器3XT2Sx不用管LFXT1Sx00 LFXT1选为32.768KHz晶振01 保留10 VLOCLK11 外部数字时钟源XCAPxLFXT1晶振谐振电容选择00 1pF01 6pF10 10pF11 12.5pFmsp430g2553.h中基本时钟系统的内容/************************************************************* Basic Clock Module************************************************************/#define __MSP430_HAS_BC2__ /* Definition to show that Module is available */SFR_8BIT(DCOCTL); /* DCO Clock Frequency Control */SFR_8BIT(BCSCTL1); /* Basic Clock System Control 1 */SFR_8BIT(BCSCTL2); /* Basic Clock System Control 2 */SFR_8BIT(BCSCTL3); /* Basic Clock System Control 3 */#define MOD0 (0x01) /* Modulation Bit 0 */#define MOD1 (0x02) /* Modulation Bit 1 */#define MOD2 (0x04) /* Modulation Bit 2 */#define MOD3 (0x08) /* Modulation Bit 3 */#define MOD4 (0x10) /* Modulation Bit 4 */#define DCO0 (0x20) /* DCO Select Bit 0 */#define DCO1 (0x40) /* DCO Select Bit 1 */#define DCO2 (0x80) /* DCO Select Bit 2 */#define RSEL0 (0x01) /* Range Select Bit 0 */#define RSEL1 (0x02) /* Range Select Bit 1 */#define RSEL2 (0x04) /* Range Select Bit 2 */#define RSEL3 (0x08) /* Range Select Bit 3 */#define DIVA0 (0x10) /* ACLK Divider 0 */#define DIVA1 (0x20) /* ACLK Divider 1 */#define XTS (0x40) /* LFXTCLK 0:Low Freq. / 1: High Freq. */ #define XT2OFF (0x80) /* Enable XT2CLK */#define DIVA_0 (0x00) /* ACLK Divider 0: /1 */#define DIVA_1 (0x10) /* ACLK Divider 1: /2 */#define DIVA_2 (0x20) /* ACLK Divider 2: /4 */#define DIVA_3 (0x30) /* ACLK Divider 3: /8 */#define DIVS0 (0x02) /* SMCLK Divider 0 */#define DIVS1 (0x04) /* SMCLK Divider 1 */#define SELS (0x08) /* SMCLK Source Select 0:DCOCLK /1:XT2CLK/LFXTCLK */#define DIVM0 (0x10) /* MCLK Divider 0 */#define DIVM1 (0x20) /* MCLK Divider 1 */#define SELM0 (0x40) /* MCLK Source Select 0 */#define SELM1 (0x80) /* MCLK Source Select 1 */#define DIVS_0 (0x00) /* SMCLK Divider 0: /1 */#define DIVS_1 (0x02) /* SMCLK Divider 1: /2 */#define DIVS_2 (0x04) /* SMCLK Divider 2: /4 */#define DIVS_3 (0x06) /* SMCLK Divider 3: /8 */#define DIVM_0 (0x00) /* MCLK Divider 0: /1 */#define DIVM_1 (0x10) /* MCLK Divider 1: /2 */#define DIVM_2 (0x20) /* MCLK Divider 2: /4 */#define DIVM_3 (0x30) /* MCLK Divider 3: /8 */#define SELM_0 (0x00) /* MCLK Source Select 0: DCOCLK */#define SELM_1 (0x40) /* MCLK Source Select 1: DCOCLK */#define SELM_2 (0x80) /* MCLK Source Select 2: XT2CLK/LFXTCLK */#define SELM_3 (0xC0) /* MCLK Source Select 3: LFXTCLK */#define LFXT1OF (0x01) /* Low/high Frequency Oscillator Fault Flag */#define XT2OF (0x02) /* High frequency oscillator 2 fault flag */#define XCAP0 (0x04) /* XIN/XOUT Cap 0 */#define XCAP1 (0x08) /* XIN/XOUT Cap 1 */#define LFXT1S0 (0x10) /* Mode 0 for LFXT1 (XTS = 0) */#define LFXT1S1 (0x20) /* Mode 1 for LFXT1 (XTS = 0) */#define XT2S0 (0x40) /* Mode 0 for XT2 */#define XT2S1 (0x80) /* Mode 1 for XT2 */#define XCAP_0 (0x00) /* XIN/XOUT Cap : 0 pF */#define XCAP_1 (0x04) /* XIN/XOUT Cap : 6 pF */#define XCAP_2 (0x08) /* XIN/XOUT Cap : 10 pF */#define XCAP_3 (0x0C) /* XIN/XOUT Cap : 12.5 pF */#define LFXT1S_0 (0x00) /* Mode 0 for LFXT1 : Normal operation */ #define LFXT1S_1 (0x10) /* Mode 1 for LFXT1 : Reserved */#define LFXT1S_2 (0x20) /* Mode 2 for LFXT1 : VLO */#define LFXT1S_3 (0x30) /* Mode 3 for LFXT1 : Digital input signal */#define XT2S_0 (0x00) /* Mode 0 for XT2 : 0.4 - 1 MHz */#define XT2S_1 (0x40) /* Mode 1 for XT2 : 1 - 4 MHz */#define XT2S_2 (0x80) /* Mode 2 for XT2 : 2 - 16 MHz */#define XT2S_3 (0xC0) /* Mode 3 for XT2 : Digital input signal */基本时钟系统例程(DCO)MSP430G2553在上电之后默认CPU执行程序的时钟MCLK来自于DCO时钟。

基于MSP430G2553的电压表设计

数字式直流电压表一、整体说明在电子技术中，往往离不开对电压的测量，作为一种测量电压的仪器——电压表是近代电子技术领域的常用工具之一，在许多领域得到广泛应用。

本设计是基于TI单片机设计的数字式直流电压表，它主要由MSP430G2553、LCD12864和分压电路三部分组成。

分压电路先将输入的电压信号衰减一定的倍数，后通过控制双路选择开关设定测量的量程，分别有0~3V和0~15V两个档，以便实现精确读数；分压处理后的电压信号由MSP430G2553内部的ADC10模块转换成数字信号；再通过LCD12864液晶屏进行串行显示。

经多次测量实验得出误差范围在2%以内。

二、原理图基于MSP430G2553单片机设计的数字式直流电压表的电路图如图1所示。

由于MSP430开发板已具备单片机最小系统结构，只需添加显示电路和分压电路。

LCD12864通过串口方式显示，只需占用单片机2个I/O口；分压电路可以通过开关S1选择量程档位，只占用1个I/O口。

图1 直流电压表电路图三、接口定义MSP430G2553的接口说明如表1所示。

图1中的复位和晶振部分是MSP430开发板固有的部分，故不再说明。

P1.0接液晶屏的SID脚，作为串行的数据口用；P1.1则接液晶屏的SCLK脚，控制串行的同步时钟；P1.4接分压电路的输出端。

LCD12864的接口说明如表2所示。

当PSB脚接低电平时，串口模式被选择。

在该模式下，只用2根线（SID与SCLK）来完成数据传输。

RS接高电平，不使用片选功能。

注意：信号源与单片机之间要共地。

表1 MSP430G2553的接口说明表2 LCD12864的接口说明四、程序流程图（一）主函数主函数的流程框图如图1所示。

主函数主要是调用系统初始化函数和循环开启ADC 转换，这是由于ADC10采用单通道单次转换模式，每次采样后需要重新开启ADC ，才会进行下一次信号采样转换。

另外，信号的采样与处理以及电压值的显示都是通过中断来完成。

msp430g2553串口通信

MSP430g2553串口通信MSP430的不同型号，其串行通讯工作模式是一样的。

以MSP430G2553为例进行说明。

MSP430G2553是20个引脚的16位单片机。

具有内置的16位定时器、16k 的FLASH 和512B 的RAM ，以及一个通用型模拟比较器以及采用通用串行通信接口的内置通信能力。

此外还具有一个10位的模数(A/D)转换器。

其引脚排布如图1.1所示。

其功能表如表1.1所示。

串行通讯模块主要由三个部分组成：波特率生成部分、发送控制器以及接收控制器。

如图1.2所示。

一、UART 模式在异步模式下，接收器自身实现帧的同步，外部的通讯设备并不使用这一时钟。

波特率的产生是在本地完成的。

异步帧格式由1个起始位、7或8个数据位、校验位（奇/偶/无）、1个地址位、和1或2个停止位。

一般最小帧为9个位，最大为13位。

图1.2 串行通讯模块内部结构图图1.1 MSP430G2553引脚图（一）UART的初始化单片机工作的时钟源来自内部三个时钟或者外部输入时钟，由SSEL1、SSEL0，以决定最终进入模块的时钟信号BRCLK的频率。

所以配置串行通讯的第一步就是选择时钟。

通过选择时钟源和波特率寄存器的数据来确定位周期。

所以波特率的配置是串行通讯中最重要的一部分。

波特率设置用三个寄存器实现：UxBR0（选择控制器0）：波特率发生器分频系数低8位。

UxBR1（选择控制器1）：波特率发生器分频系数高8位。

UxMCTL 数据传输的格式，以及数据传输的模式是通过配置控制寄存器UCTL来进行设置。

接收控制部分和发送控制部分。

首先需要串行口进行配置、使能以及开启中断。

串口接收数据一般采用中断方式，发送数据采用主动发送。

当接收到一个完整的数据，产生一个信号：URXIFG0=1（类似于51单片机的接收中断标志位），表示接收完整的数据。

当数据正在发送中，UTXIFG0=1，此时不能再发送数据，必须等当前数据发送完毕（UTXIFG0=0）才能进行发送。

1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。

MSP-EXP430G2LaunchPad Evaluation Kit User's GuideLiterature Number:SLAU318EJuly2010–Revised March2014Contents 1MSP-EXP430G2LaunchPad Overview (4)1.1Overview (4)1.2Features (5)1.3Kit Contents (5)1.4Revisions (6)2Installation (6)2.1Download the Required Software (6)2.2Install the Software (6)2.3Install the Hardware (6)3Getting Started With MSP-EXP430G2LaunchPad (7)3.1Getting Started (7)3.2Demo Application,Internal Temperature Measurement (7)4Develop an Application With the MSP-EXP430G2LaunchPad (8)4.1Developing an Application (8)4.2Program and Debug the Temperature Measurement Demo Application (8)4.3Disconnect Emulator From Target With Jumper J3 (9)4.4Program Connected eZ430Target Boards (10)4.5Connecting a Crystal Oscillator (10)4.6Connecting a BoosterPack (11)4.7Supported Devices (11)4.8MSP-EXP430G2On-Board Emulator (13)5MSP-EXP430G2Hardware (13)5.1Device Pinout (13)5.2Schematics (14)5.3PCB Layout (20)5.4Bill of Materials(BOM) (23)6Suggested Reading (24)7Frequently Asked Questions(FAQ) (24)Revision History (26)2Table of Contents SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedList of Figures1MSP-EXP430G2LaunchPad Overview (5)2Insert Device Into Target Socket (8)3Code Composer Studio™v4in Debugging Mode (9)4MSP-EXP430G2LaunchPad With Attached eZ430-RF2500Target Board (10)5Device Pinout (13)6Schematics,MSP-EXP430G2Emulator(1of2),Revision1.4 (14)7Schematics,MSP-EXP430G2Emulator(2of2),Revision1.4 (15)8Schematics,MSP-EXP430G2Target Socket,Revision1.4 (16)9Schematics,MSP-EXP430G2Emulator(1of2),Revision1.5 (17)10Schematics,MSP-EXP430G2Emulator(2of2),Revision1.5 (18)11Schematics,MSP-EXP430G2Target Socket,Revision1.5 (19)12Layout,LaunchPad Top Layer (20)13Layout,LaunchPad Bottom Layer (21)14Layout,LaunchPad Silkscreen (22)List of Tables1Jumper Connection J3Between Emulator and Target (9)2eZ430Debugging Interface (10)3Supported Devices (11)4Features Supported by On-Board Emulator (13)5Bill of Materials (23)3 SLAU318E–July2010–Revised March2014List of Figures Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedUser's GuideSLAU318E–July2010–Revised March2014 MSP-EXP430G2LaunchPad Evaluation KitPreface:Read This FirstIf You Need AssistanceIf you have any feedback or questions,support for the MSP430™devices and the MSP-EXP430G2isprovided by the Texas Instruments Product Information Center(PIC)and the TI E2E Forum(/).Contact information for the PIC can be found on the TI web site at .Additional device-specific information can be found on the MSP430web site at /msp430. Related Documentation from Texas InstrumentsThe primary sources of MSP430information are the device-specific data sheets and user's guidesavailable at the Texas Instruments MSP430web site:/msp430.MSP430device user's guides,application reports,software examples and other MSP430user's guides can be found at the Tech Docs section.The CCS user's guide includes detailed information on setting upa project and using Code Composer Studio™for the MSP430microcontroller(SLAU157).Information specific to the MSP-EXP430G2LaunchPad Evaluation Kit,all the available IDEs,Software Libraries,and examples can be found at the Tools&Software section:/tool/msp-exp430g2.1MSP-EXP430G2LaunchPad Overview1.1OverviewThe MSP-EXP430G2LaunchPad is an inexpensive and simple evaluation kit for the MSP430G2xx Value Line series of microcontrollers.It is an easy way to start developing on the MSP430with on-boardemulation for programming and debugging as well as buttons and LEDs for a simple user interface.Rapid prototyping is simplified by the20-pin BoosterPack headers which support a wide range of available BoosterPack plug-in modules.You can quickly add features like wireless connectivity,graphical displays, environmental sensing,and much more.You can either design your own BoosterPack or choose among many already available from TI and third party developers.The LaunchPad features an integrated DIP target socket that supports up to20pins,allowing MSP430™Value Line devices to be plugged into the LaunchPad board.The MSP-EXP430G2LaunchPad comeswith an MSP430G2553device by default.The MSP430G2553has the most memory available of thecompatible Value Line devices.The MSP430G255316-bit MCU has16KB flash,512bytes RAM,up to16-MHz CPU speed,10-bit ADC, capacitive touch enabled I/Os,universal serial communication interface,and more–plenty to get youstarted in your development.Free software development tools are also available:TI's Eclipse-based Code Composer Studio™IDE(CCS),IAR Embedded Workbench™IDE(IAR),and the community-driven Energia open source codeeditor.More information about the LaunchPad,including documentation and design files,can be found on the tool page at /tool/msp-exp430g2.MSP430,Code Composer Studio are trademarks of Texas Instruments.IAR Embedded Workbench is a trademark of IAR Systems.All other trademarks are the property of their respective owners.4MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated MSP-EXP430G2LaunchPad Overview 1.2FeaturesMSP-EXP430G2LaunchPad features:•USB debugging and programming interface featuring a driverless installation and application UART serial communication with up to9600Baud•Supports MSP430G2xx2,MSP430G2xx3,and MSP430F20xx devices in PDIP14or PDIP20packages (see Section4.7for a complete list of supported devices)•Two general-purpose digital I/O pins connected to green and red LEDs for visual feedback•Two push button for user feedback and device reset•Easily accessible device pins for debugging purposes or as socket for adding customized extension boards•High-quality20-pin DIP socket for an easy plug-in or removal of the target deviceFigure1.MSP-EXP430G2LaunchPad Overview1.3Kit ContentsThe MSP-EXP430G2evaluation kit includes the following hardware:•LaunchPad emulator socket board(MSP-EXP430G2)•Mini USB-B cable,0.5m•Two MSP430flash devices–MSP430G2553:Low-power16-bit MSP430microcontroller with an8-channel10-bit ADC,on-chip comparator,touch-sense enabled I/Os,universal serial communication interface,16kB flashmemory,and512bytes of RAM(preloaded with a sample program)–MSP430G2452:Low-power16-bit MSP430microcontroller with an8-channel10-bit ADC,on-chip comparator,touch-sense enabled I/Os,universal serial interface,8kB flash memory,and256bytesof SRAM•Two10-pin PCB connectors female•32.768-kHz clock crystal from Micro Crystal()•Quick start guide•Two LaunchPad stickers5 SLAU318E–July2010–Revised March2014MSP-EXP430G2LaunchPad Evaluation Kit Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedInstallation 1.4RevisionsThe first production revision of the LaunchPad in2010was1.3.In2012the LaunchPad board revision changed from1.4to1.5to align with the new release of Value Line devices.The differences in theschematic and the kit contents are:•Layout and Schematic:–Voltage feedback in the emulator changed to increase startup stability(Rev1.3to Rev1.4)–Rearranged jumper J3to support two UART configurations:vertical(SW UART),horizontal(HW UART)–VCC on the connector J4can now be disconnected from the emulator VCC by J3–Pullup resistor R34and capacitor C24on P1.3removed to reduce the current consumption–Presoldered male headers J1and J22InstallationThe MSP-EXP430G2LaunchPad installation consists of three easy steps:1.Download the required software.2.Install the selected IDE.3.Connect the LaunchPad to the PC.Then the LaunchPad is ready to develop applications or to use the pre-programmed demo application.2.1Download the Required SoftwareDifferent development software tools are available for the MSP-EXP430G2LaunchPad developmentboard.IAR Embedded Workbench™KickStart IDE and Code Composer Studio™(CCS)IDE are bothavailable in a free limited version.IAR Embedded Workbench allows4KB of C-code S is limited to a code size of16KB.The software is available at /mspds.There are manyother compilers and integrated development environments(IDEs)available to use with the MSP-EXP430 LaunchPad including Rowley Crossworks and MSPGCC.However,example projects have been created using IAR Embedded Workbench KickStart IDE and Code Composer Studio IDE(CCS).For moreinformation on the supported software and the latest code examples,visit the LaunchPad tool page(/tool/msp-exp430g2).2.2Install the SoftwareDownload one of the integrated development environments(IDEs)(see Section2.1).IAR KickStart and CCS offer the required driver support to work with the MSP-EXP430LaunchPad onboard emulation.Once installed,the IDE should find the MSP-EXP430G2LaunchPad as USB:HID debugging interface.Now all is set for developing MSP430G2xx based application on the LaunchPad.2.3Install the HardwareConnect the MSP-EXP430G2LaunchPad socket board with the enclosed USB cable to a PC.The driver installation starts automatically.If prompted for software,allow Windows to install the softwareautomatically.This is possible only if either IAR KickStart or CCS is already installed.6MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated Getting Started With MSP-EXP430G2LaunchPad 3Getting Started With MSP-EXP430G2LaunchPad3.1Getting StartedThe first time the MSP-EXP430G2LaunchPad Evaluation Kit is used,a demo application automatically starts as soon as the board is powered from the USB host.To start the demo,connect the MSP-EXP430G2LaunchPad with the included mini USB cable to a free USB port.The demo application starts with an LED toggle to show the device is active.More information about the demo application can befound in Section3.2.3.2Demo Application,Internal Temperature MeasurementThe LaunchPad includes a pre-programmed MSP430G2553device already installed in the target socket.When LaunchPad is connected via USB,the demo starts with an LED toggle sequence.The onboardemulation generates the supply voltage and all the signals necessary to start.Press button P1.3to switch the application to a temperature measurement mode.A reference temperature is taken at the beginning of this mode,and the LEDs of the LaunchPad signal a rise or fall in temperature by varying the brightness of the on-board red or green LED,respectively.The reference temperature can also be recalibrated with another button press on P1.3.The collected temperature data is alsocommunicated via back-channel UART through the USB emulation circuitry back to the PC.The internal temperature sensor data from the MSP430G2553device is sent to the PC to be displayed on the GUI.The pre-loaded demo application and the GUI are found in the Software Examples zip folder.The GUI is opened with LaunchPad_Temp_GUI.exe.This GUI is made with Processing()with the source available for customization.The serial communication port on the PC must be configured with 2400bps,one stop bit,and no flow control to display the values correctly.The demo application uses the on-chip peripherals of the MSP430G2553device such as the10-bit ADC, which samples the internal temperature sensor,and16-bit timers,which drive the PWM to vary brightness of the LEDs and enable software UART for communication with the PC.The MSP430G2553offers a USCI interface that is capable of communicating through UART at up to2MBaud,but to be aligned with all the other MSP430G2xx devices,the demo uses the Timer UART implementation,which can be used on all the other devices.This way the demo can be used with any other MSP430G2xx device with an integrated ADC,without any change in the program.The provided applications can be a great starting point for various custom applications and give a good overview of the various applications of the MSP430G2xx Value Line devices.7 SLAU318E–July2010–Revised March2014MSP-EXP430G2LaunchPad Evaluation Kit Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated4Develop an Application With the MSP-EXP430G2LaunchPad4.1Developing an ApplicationThe integrated development environments(IDEs)shown in Section2offer support for the wholeMSP430G2xx Value Line.The MSP-EXP430G2LaunchPad needs only a connection to the USB of the Host PC—there is no external hardware required.The power supply and the Spy-Bi-Wire JTAG signals TEST and RST must be connected with jumper J3to allow the onboard emulation connection to thedevice.Now the preferred device can be plugged into the DIP target socket of the LaunchPad(seeFigure2).Both PDIP14and PDIP20devices of the MSP430G2xx Value Line and the MSP430F20xxfamily can be inserted into the DIP socket aligned to pin1.A complete list of supported devices can be found in Section4.7.Figure2.Insert Device Into Target SocketThe following example for Code Composer Studio shows how to download and debug the demoapplication described in Section3.2.4.2Program and Debug the Temperature Measurement Demo ApplicationThe source code of the demo application can be found in the Software Examples zip folder.Download the project folder and unpack it to a location of your choice.For this demo,Code Composer Studio v4ornewer must be installed.The demo application can be loaded to the CCS workspace by clicking File→Import.Select the location of the extracted project files and import Existing projects into Workspace.Now the MSP-EXP430G2-Launchpad project appears inside the CCS workspace.The project must be marked as the active project to start programming and debugging the device.Connect the LaunchPad with an inserted MSP430G2553device to the host PC and click the Debug button on the CCS Toolbar.The MSP-EXP430G2LaunchPad is initialized and the download of the compileddemo application starts.The CCS view switches to a debugging interface once the download is completed and the application is ready to start.Figure3shows Code Composer Studio v4with the MSP-EXP430G2 LaunchPad demo application in debug view.8MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedFigure3.Code Composer Studio™v4in Debugging Mode4.3Disconnect Emulator From Target With Jumper J3The connection between the MSP-EXP430G2emulator and the attached target device can be opened with the jumper array J3.This can be useful to access an attached eZ430target board by disconnecting the Spi-Bi-Wire JTAG lines RST and TEST or if the JTAG lines are used for other application purposes.The jumper array can also be used to measure the power consumption of the LaunchPad application.For this intention,all connections except VCC must be opened,and a multi meter can used on the VCCJumper to measure the current of the MSP-EXP430G2target device and its peripherals.The jumper J5 VCC also must be opened if the LaunchPad board is powered with an external power supply over J6Table1or the eZ430interface J4.NOTE:The assignment of jumper J3has been changed in MSP-EXP430G2revision1.5,see thecomments in Table1to find the assignment for a specific board revision.Table1.Jumper Connection J3Between Emulator and TargetJumper Signal Description1VCC Target socket power supply voltage(power consumption test jumper)(located on5before Rev.1.5)Test mode for JTAG pins or Spy-Bi-Wire test clock input during programming and test(located on1before 2TESTRev.1.5)3RST Reset or Spy-Bi-Wire test data input/output during programming and test(located on2before Rev.1.5)4RXD UART receive data input(direction can be selected by jumper orientation)(located on3before Rev.1.5)5TXD UART transmit data output(direction can be selected by jumper orientation)(located on4before Rev.1.5)Jumpers4and5connect the UART interface of the emulator to the target device pins P1.1and P1.2.The direction of the UART signal lines can be selected by the orientation of the attached jumpers.In horizontal orientation,the jumpers connect TXD to P1.1and RXD to P1.2,as they are used for the software UART communication on the demo application(see Section3.2).In vertical orientation,the jumpers connect the TXD signal to P1.2and the RXD signal to P1.1,as required for the MSP430G2553USCI.9 SLAU318E–July2010–Revised March2014MSP-EXP430G2LaunchPad Evaluation Kit Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated4.4Program Connected eZ430Target BoardsThe MSP-EXP430G2LaunchPad can program the eZ430-RF2500T target boards,the eZ430-Chronos watch module,or the eZ430-F2012T/F2013T.To connect one of the ez430targets,connector J4must be populated with a0.050-in(1.27-mm)pitch male header,as shown in Figure4.Figure4.MSP-EXP430G2LaunchPad With Attached eZ430-RF2500Target Board To program the attached target without interfering with the LaunchPad socket board,jumper connections TEST and RST of J3must be open.The interface to the eZ430target board is always connected to the MSP-EXP430G2emulator,so the programming and debugging of a connected LaunchPad target device is possible only if the eZ430target is not connected on the same time.The application UART,on the other hand,is connected directly to the LaunchPad target device,and jumper J3can be closed to monitor the transmission from the LaunchPad target to the attached eZ430.This way both possible connections,from the device to the PC and from the device to the eZ430,can be established without changing the direction of the UART pins.The VCC connection to the eZ430interface is directly connected to the LaunchPad target VCC and can be separated with jumper J3,if the LaunchPad itself should be powered via a connected battery on J4.To supply the eZ430interface with the onboard emulator the jumper J3VCC needs to be closed.Table2shows the pinout of the eZ430debugging interface J4,the first pin is the left pin located on the emulator part of the LaunchPad.Table2.eZ430Debugging InterfacePin Signal Description1TXD UART transmit data output(UART communication from PC or MSP430G2xx to eZ430target board)2VCC Power supply voltage(J3VCC needs to be closed to supply via onboard emulator)3TEST/SBWTCK Test mode for JTAG pins and Spy-Bi-Wire test clock input during programming and test4RST/SBWTDIO Reset,Spy-Bi-Wire test data input/output during programming and test5GND Power supply ground6RXD UART receive data input(UART communication from eZ430target board to PC or MSP430G2xx)4.5Connecting a Crystal OscillatorThe MSP-EXP430G2LaunchPad offers a footprint for a variety of crystal oscillators.The XIN and XOUT signals of the LFXT1oscillator can support low-frequency oscillators like a watch crystals of32768Hz or a standard crystal with a range defined in the associated data sheet.The signal lines XIN and XOUT can also be used as multipurpose I/Os or as a digital frequency input.More information on the possibilities of the low-frequency oscillator and the possible crystal selection can be found in the MSP430x2xx Family User's Guide(SLAU144)or the device-specific data sheet.The oscillator signals are connected to J2to use the signals on an attached application board.In case of signal distortion of the oscillator signals that leads to a fault indication at the basic clock module,resistors R29and R28can be used to disconnect the pin header J2from the oscillating lines.10MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated4.6Connecting a BoosterPackThe LaunchPad can connect to many BoosterPacks within the ecosystem.The BoosterPack headers J1 and J2along with power supply J6fall on a100-mil(0.1-in)grid to allow for easy and inexpensivedevelopment with a breadboard.The LaunchPad adheres to the20-pin LaunchPad pinout standard.Astandard was created to aid compatibility between LaunchPads and BoosterPacks,across the TIecosystem.The20-pin standard is backward compatible with the40-pin standard used by LaunchPads like the MSP-EXP430F5529LP.This allows a subset of some40-pin BoosterPacks to be used with20-pin LaunchPads.While most BoosterPacks are compliant with the standard,some are not.The LaunchPad is compatible with all20-pin(and40-pin)BoosterPacks that are compliant with the standard.If the reseller or owner of the BoosterPack does not explicitly indicate compatibility with the MSP430G2LaunchPad,you might want to compare the schematic of the candidate BoosterPack with the LaunchPad,to ensure compatibility.Keep in mind that sometimes conflicts can be resolved by changing the G2device pin functionconfiguration in software.More information about compatibility can also be found at/launchpad.4.7Supported DevicesTexas Instruments offers several MSP430devices in a PDIP package that is compatible with LaunchPad.Table3shows the supported devices.Table3.Supported Devices11 SLAU318E–July2010–Revised March2014MSP-EXP430G2LaunchPad Evaluation Kit Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedTable3.Supported Devices(continued)12MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated MSP-EXP430G2Hardware 4.8MSP-EXP430G2On-Board EmulatorThe MSP-EXP430G2on-board emulator enables programming and debugging of supported MSP430devices(see Section4.7).It offers several features that are enabled by a2-wire JTAG interface calledSpy-Bi-Wire.For a more feature-complete emulator,the MSP-FET430UIF flash emulation tool may bemore appropriate.See Table4for more details on the MSP-EXP430G2LaunchPad on-board emulator.Table4.Features Supported by On-Board EmulatorSupport by LaunchPadFeature(MSP-EXP430G2) Supports MSP430F20xx,F21x2,F22xx,G2x01,G2x11,G2x21,G2x31,G2x53✓Allows fuse blowAdjustable target supply voltageFixed2.8-V target supply voltageFixed3.6-V target supply voltage✓4-wire JTAG2-wire JTAG✓Application UART✓Supported by CCS✓Supported by IAR✓5MSP-EXP430G2Hardware5.1Device PinoutFigure5.Device Pinout13 SLAU318E–July2010–Revised March2014MSP-EXP430G2LaunchPad Evaluation Kit Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedMSP-EXP430G2Hardware 5.2SchematicsFigure6.Schematics,MSP-EXP430G2Emulator(1of2),Revision1.414MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated MSP-EXP430G2HardwareFigure7.Schematics,MSP-EXP430G2Emulator(2of2),Revision1.415 SLAU318E–July2010–Revised March2014MSP-EXP430G2LaunchPad Evaluation Kit Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedMSP-EXP430G2Hardware Figure8.Schematics,MSP-EXP430G2Target Socket,Revision1.416MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated MSP-EXP430G2HardwareFigure9.Schematics,MSP-EXP430G2Emulator(1of2),Revision1.517 SLAU318E–July2010–Revised March2014MSP-EXP430G2LaunchPad Evaluation Kit Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedMSP-EXP430G2Hardware Figure10.Schematics,MSP-EXP430G2Emulator(2of2),Revision1.518MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated MSP-EXP430G2HardwareFigure11.Schematics,MSP-EXP430G2Target Socket,Revision1.519 SLAU318E–July2010–Revised March2014MSP-EXP430G2LaunchPad Evaluation Kit Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedMSP-EXP430G2Hardware 5.3PCB Layoutyout,LaunchPad Top Layer20MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated MSP-EXP430G2Hardwareyout,LaunchPad Bottom Layer21 SLAU318E–July2010–Revised March2014MSP-EXP430G2LaunchPad Evaluation Kit Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedMSP-EXP430G2Hardware yout,LaunchPad Silkscreen22MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated MSP-EXP430G2Hardware 5.4Bill of Materials(BOM)Table5.Bill of MaterialsNumberPos.Ref Name Descriptionper Board1C2,C3216pF0402(33pF on Rev1.3)2C9,C10222pF04023C1110nF04024C5,C7,C11,C12,C135100nF04025C4,C6,C831µF,6.3V06046D111N4148MicroMELF7EZ_USB1Mini-USB connector8Q11SMD oscillator12MHz9R1,R2,R3,R16,R17347k0402(R16,R17is not populated)10R8161k50402(6k8in Rev1.3and prior)11R19,R2223k3040212R9130k0402(3k3in Rev1.3and prior)13R12,R21233k040214R4,R5,R6,R7,R235100R040215R14,R15233R040216R18,R202100k040217R13,R24,R2531k5040218R10110k040219R11115k040220U11MSP430F1612IPMR21U41TPD2E001DRLR22U31TUSB3410VF23U21TPS77301DGKR24U51I2C EEPROM128k(AT24C128-10TU-2.7)TP1,TP2,TP3,TP4,25TP5,TP6,TP726C1411nF,SMD060327C21,C2212.5pF,SMD0603(not populated)28C23110µF,10V,SMD080529C20,C241100nF,SMD0603(C24is not populated)30LED0,LED12Green DIODE060331LED21Red DIODE060332R34,R27147k SMD0603(R34is not populated)33R32,R262270R SMD060334R331470R SMD060335R28,R2920R SMD060336IC11DIP20socketClock crystal32kHz(Micro Crystal MS3V-T1R32.768kHz CL:12.5pF±20ppm 37Q2included)38J1,J2,210-pin header,TH,2.54mm male(female header included)39J312X05pin header male40J46pin header male1.28mm41J512x02pin header male42J623-pin header,male,TH43S1,S22Push button23 SLAU318E–July2010–Revised March2014MSP-EXP430G2LaunchPad Evaluation Kit Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments IncorporatedSuggested Reading 6Suggested ReadingThe primary sources of MSP430™information are the device-specific data sheets and the family user's guides.The most up-to-date versions of those documents can be found at the Texas Instruments MSP430 landing page.For more information on CCS and IAR,download the latest version from /mspds andread the included user's guides and documentation in the installation folder.Documents describing the IAR tools(Workbench/C-SPY,the assembler,the C compiler,the linker,and the library)are located incommon\doc and430\doc.All necessary CCS documents can be found in the msp430\doc folder in the CCS installation path.The FET user's guide also includes detailed information on how to set up a project for the MSP430using IAR or CCS,and it is included in most of the IDE releases and on the TI MSP430 side.7Frequently Asked Questions(FAQ)1.Can other programming tools like the MSP-FET430UIF interface the MSP-EXP430G2LaunchPadsocket device?The LaunchPad evaluation kit works with any programming tool that supports the2-wire Spy-Bi-Wireinterface.Both the MSP430USB FET(MSP-FET430UIF)and the Gang Programmer(MSP-GANG430) support these devices,but the connection must be made directly to the dedicated Spy-Bi-Wire ports.See MSP-FET430Flash Emulation Tool User's Guide(SLAU138)for details on using MSP430USBFET and the Gang Programmer for a2-wire Spy-Bi-Wire interface.Do not try to connect the standardJTAG connector to the MSP-EXP430G2pinheads,as this could result in damage to the attachedhardware.2.Does the MSP-EXP430G2support fuse blow?The MSP-EXP430G2LaunchPad evaluation kit onboard debugging interface lacks the JTAG securityfuse-blow capability.To ensure firmware security on devices going to production,the USB FlashEmulation Tool or the Gang Production Programmer,which support the fuse-blow feature,arerecommended.3.What versions of IAR Embedded Workbench and Code Composer Studio are supported?The MSP-EXP430G2LaunchPad hardware is supported by IAR Embedded Workbench KickStartVersion6.00or higher and Code Composer Studio v4or higher.To download the IDE visit/mspds.4.What are the part numbers for the connectors between the LaunchPad emulator board and the othereZ430target boards?Header:MALE CONN HEADER.050"6POS PCB R/A(for example,Digi-Key:S9016E-06-ND)Socket:FEMALE CONN HEADER.050"6POS PCB R/A(for example,Digi-Key:S9010E-06-ND)5.I am not able to select the MSP430Application UART and cannot receive data.Ensure that the Application UART driver is correctly installed.This is done by installing either IAREmbedded Workbench or Code Composer Studio v4.To determine if the driver is correctly installed:a.Plug in the MSP-EXP430G2LaunchPad with the included Mini USB cable.b.Right click My Computer and select Properties.c.Select the Hardware tab and click on Device Manager.d.Under Ports(COM&LPT)should be an entry for"MSP430Application UART(COM xx)".If the entry is there,but no characters are received,reconnect the LaunchPad to the PC and restart the application to reload the drivers.If the Application UART is not listed,install the driver by following theinstructions in Section2.2.If the application UART is installed but not receiving UART data,ensure that the jumpers on J3areconfigured for the proper UART communication.The two UART jumpers are configured vertically for asoftware(SW)UART,and horizontally for a hardware(HW)UART.The application implementation and J3jumpers should match for UART data to be properly transmitted.24MSP-EXP430G2LaunchPad Evaluation Kit SLAU318E–July2010–Revised March2014Submit Documentation FeedbackCopyright©2010–2014,Texas Instruments Incorporated。