锂离子电池规格书

合集下载

锂电池规格书(中英文)

锂电池规格书(中英文)

History of revision版本更改历史记录Contents 目录1.Scope 适用范围 32.Adopted Standard引用标准 33.Electrical Characteristics电气特性 34.Battery Performances Test Criterion 电池性能测试规范 35.1 Appearance 外观 35.2 Measurement Apparatus 测试设备 35.3 Testing Condition 测试条件 35.4 Reliability Test 可靠性测试 35.Shipment 运输 36.Storage 贮存 37.Package and Marking包装与标志 38.1 Package 包装 38.2 Marking 标志 38.Protection Circuit 保护电路 39.1 Schematic of the PCB 保护板原理图 39.2 PCM BOM9.3 PCM Parameter PCM参数 39.Outline Drawing 外形图纸 310.Appendix 附录 33.7 Instructions and Safety Requirement 使用说明和安全规程 33.7.1 Recommending Usage推荐使用事项 33.7.2 Hazard Warning危险警告 33.7.3 Warning 警告 33.7.4 Cautions 注意事项 310.2 Quality Evaluation Programme 质量评定 310.3 Environment Protection 环保要求 310.4 Others 其他事项 31.Scope 适用范围This description defines the general requirements for thebattery’s rating parameter, electrical requirement, safety requirement, environmental compatibility, test and judgment, usage instructions, safety regulation, quality evaluation and packaging, marking, storage,shipment and handling, which cellular phone battery with 523450AR-850mAh rechargeable battery cell, adapted for Digital products.本规格书描述电池之标称参数、电气特性、安全性能、环境适应性及其实验和判定、使用说明和安全规程、质量评定及包装、标志、贮存、运输等。

聚合物锂离子电池产品规格书说明书

聚合物锂离子电池产品规格书说明书

Product Specification for Li-ion Polymer Battery 聚合物锂离子电池产品规格书Model电芯型号: 702427(PCM)惠州基安比新能源有限公司HUIZHOU MARKYN NEW ENERGY CO.,LTD.电话: ************传真: ************TEL: ************ FAX : ************SPECIFICATION AMENDMENT RECORDS规格书变更记录1. Scope适用范围:This document describes the Product Specification of the Li-Polymer Rechargeable Battery supplied by Huizhou Markyn New Energy Co., LTD.本规格书描述了惠州基安比新能源有限公司的可充电锂离子聚合物电池的产品性能指标。

2. Description 说明2.1 Description: Li-Polymer Battery类型:锂离子聚合物电池2.2 Model: 702427型号:7024273. Specification产品规格4. Battery Cell Performance Criteria 电芯性能标准4.1 Standard testing environment标准测试环境Unless specifically stated otherwise, tests must be done within one month of delivery and the number of charging-recharging cycles is fewer than 5. The following is test conditions:Test conditions:Ambient Temperature:23ºC ± 2ºCAmbient Humidity:65±20%RH除非另有说明,测试应在电池出货的1个月内进行,且充放电循环的次数少于5次。

4812动力型锂离子产品规格书

4812动力型锂离子产品规格书
湿度:MAX. 85%
放电
-20℃~70℃
2.1.9储存温度
1个月以内
-20℃~55℃
3个月以内
-20℃~45℃
6个月以内
-5℃~25℃
2.1.10 内阻
≤220mΩ
标准充电后24h内测得的AC 1KHz 交流阻抗值
2.2 尺寸及外观
2.2.1 尺寸:依据电池外壳(长*宽*高mm)
2.2.2 重量:约4Kg(含外壳)
1.2产品描述
1.2.1 名称:三元锂电池组
1.2.2型号:XKD4812
1.2.3 组成:磷酸铁锂电池和订制保护系统。
2产品规格
2.1 额定参数
项 目
要求参数
备 注
2.1.1额定容量
典型值
12Ah
电池按标准充电后,按标准放电所得的容量
最小值
11.8Ah
电池标准充电后按标准放电所得的最低容量
2.2.2标称电压
控制电路中的保护电路具有过充、过放及过流保护功能,主要技术参数如下:
项目
参数
备注
4.1.2.1 过充保护
充电时,如果单节电芯电压超过4.25V±0.01V,控制电路切断电路停止充电(可以放电)
通过放电可以解除保护
4.1.2.2 过放保护
放电时,如果单节电芯电压低于2.5V±0.10V,控制电路切断电路停止放电(可以充电)
48V
标准充电后标准放电过程中的平均电压
2.1.3放电终止电压
39V
当电池电压低于20V时请停止放电
2.1.4 充电方式
CC/CV
2.1.5充电电压
MAX.58.4V
2.1.6充电电流
≤0.5C(6.0A)

锂离子聚合物电池规格书说明书

锂离子聚合物电池规格书说明书

页码:1/15602030PL300mAhSpecification of Li-ion Rechargeable Battery锂离子电池规格书Model:602030PL300mAh/3.7VCustomer Confirmation Customer Name: Customer No.: Comment:Customer Approval:Prepared by Checked by Approved by 肖志军602030PL300mAh页码:2/15兴永恒(深圳)电子有限公司深圳宝安区沙井后亭E-mail:****************Website:TEL:86-0755-********FAX:86-0755-********AMENDMENT RECORDSREVISION DATE ORIGINATOR REASON FOR REVISION A001 2016-6-20602030PL300mAh页码:3/15Content目录1. Scope范围 (4)2. Reference Standard 参考标准 (4)3. Picture of battery电池图 (4)3.1 Picture of single cell 单体电芯图 (4)3.2 Picture of assembled battery 组合电池图 (6)4. Basic of performance 基本性能 (7)4.1 Single cell parameters 单体电芯参数 (7)4.2 Assembled cell parameters包装后电芯组参数 (8)5. Electrical Characteristics电性能 (8)5.1 Normal Test Conditions标准测试条件 (8)5.2 Electrochemical Characteristics电化学性能 (8)5.3 Environment Characteristics环境适应性能 (9)5.4 Safety Characteristics 安全性能 (10)6. PCM Specification PCM 规格 (11)6.1 Electrical Characteristics电性能 (11)6.2 Circuit Diagram 电路图 (11)6.3 Circuit topology Drawing and PIN Explanation电路布线图和焊盘说明 (12)6.4 PCM BOM 保护板物料清单 (12)7. Storage and Shipment Requirement存储及运输要求 (13)8. Warning and Cautions 警告及注意事项 (13)9. Note 声明 (15)页码:4/15602030PL300mAh1. Scope范围This specification describes the performance, testing method, warning and caution of the lithium-ion rechargeable battery.The specification applies to polymer battery supplied by Shenzhen biyate energy co., ltd本标准描述了锂离子电池的性能、测试方法及注意事项。

eeMB BATTERY LIR18650 3000mAh 锂离子电池 产品规格书说明书

eeMB BATTERY LIR18650 3000mAh 锂离子电池 产品规格书说明书

ModelChapter Content0Catalog………………………………………………………………………………………………….1Scope…………………………………………………………………………………………………...2Battery Basic Characteristics…………………………………………………………………………...3Battery Shape4Appearance…………………………………………………………………………………………...5Performance6Warranty……………………………………………………………………………………………....7Matters Needing1.Scope适用范围This product specificationcustomer by EEMB本产品规格书适用于2.Battery CellNo.2.12.2Capacity容量2.3Nominal2.42.5Internal3.Battery Cell 产品外形及尺寸(单位:MW L+T-L 2L 1NItem 项目Diameter Height25℃±2℃,0.3C2.75V,搁置5.2Electrical CharacteristicsITEM测试项目Discharge rate capacity倍率放电性能Cycle life循环寿命5.3AcclimatizationITEM测试项目Constant Temperature andHigh Humidity恒定湿热性能Drop test自由跌落Heating Test热冲击Overcharge Test 过充电●Strictly prohibits严禁把电池投入液体中,如水、汽油、饮料等,也不要把电池弄湿。

●Strictly prohibitsAlso do not禁止在火源附近或温度超过●Strictly prohibitsHairpins,coins,禁止把电池同项链、发夹、硬币或螺钉等金属品一起放在兜中或包中,也不要把电池同上述物品一起储存或运输。

锂离子电池规格书

锂离子电池规格书

锂离子电池规格书型号:BL-5c标称: 1000mAh修订履历1、目的对深圳市好远通电子有限公司出品的可充锂离子电池的产品规格、测试方法进行规范,避免因测试条件、方法的不同引起误差。

2、产品类别和产品型号2.1 类别:锂离子可充电池2.2 产品型号高务电池BL-5C/1000mAh3、产品基本特性4、特性4.1电性能4.2 安全性能4.3 环境适应性温度:25±2℃,相对湿度:45±20%(除非另外要求)6、产品责任书消费者必须严格遵守深圳市好远通电子有限公司规格书和文件后面的注示使用电池,由于误用会引起电池过热,发生火灾或爆炸,对于没有按照规格书进行操作所造成的任何意外事故,深圳市慧通天下科技股份有限公司不负任何责任。

7、充电前注意事项如果规格书、原材料、生产过程或生产控制系统发生改变,改变的信息将会随质量和可靠性数据以书面形式通知消费者。

8、电池包装说明在电池的包装上应有如下说明!危险*充电时请使用指定的充电器并按照说明书的要求进行充电。

*仅在指定的设备上使用电池。

*不要把电池加热或投进火中。

*不要在火源附近或温度超过60℃的轿车中使用或遗留电池,也不要在这些环境中进行充电。

*不要把电池投入水中,也不要弄湿。

*不要把电池同项链、发夹、硬币或镙钉等金属品一起放在兜里或包中,也不要把电池同上述物品一起储存。

*不要使用金属导体短路电池的正负极。

*在装入设备时注意电池的正负极不要反装。

*不要使用锐利的物品刺穿电池。

*不要对电池进行分解。

*不要直接对电池进行焊接。

*不要使用带有严重伤痕或变形的电池。

*在使用之前请详细阅读操作说明书,不适当的操作可能引起电池变热、着火、爆炸、毁坏或电池容量的衰减。

!警告*不要把电池放在加热器皿、洗衣机或高压容器中。

*不要把电池同干电池或其它原电池一起使用,也不要同不同包装、不同型号或不同品牌的电池一起使用。

*如果在规定的充电时间内充电没有结束,停止充电。

锂离子电芯产品规格书

锂离子电芯产品规格书

Product Specification for Lithium-ion Rechargeable Cell 锂离子电芯产品规格书Cell Model: WX12I3250电芯型号:WX12I3250Table of Contents目录1. Purpose 目的 (3)2. Scope 适用范围 (3)3.Battery description 电池描述 (3)4. Battery Specification 电池规格 (3)5. Appearance and Dimension 电芯外观尺寸 (5)6. Standard Test Conditions 标准测试环境 (5)7. Performances and Test Method 电池性能及测试方法 (5)7.1 Explanation of terminology 术语解释 (5)7.2 Electrochemistry performance 电性能参数 (6)7.3 Safety Performances 安全性能 (7)8. Shipment 运输 (9)9. Warning and Cautions 警告及注意事项 (9)1. Purpose 目的The specification sheet is designed to build up and improve Co.,Ltd technical documentation so as to instruct production and product shipment and consequently guarantee product quality. At the same time, it is convenient for to confirm product specifications with customers and finally reach an agreement.为建立健全的公司技术资料,确保产品质量,用于指导产品生产、出货。

锂离子电池规格书【完整版】

锂离子电池规格书【完整版】

锂离子电池规格书【完整版】(文档可以直接使用,也可根据实际需要修订后使用,可编辑放心下载)★★★★★锂离子电池规格书SpecificationForLithium Ion Rechargeable Battery电池型号〔Type〕:383450AH标称容量〔Rated Capacity〕:700mAh部门〔Department〕:铝壳制造部生效日期〔Effective Date〕:2007-3-121.范围SCOPE AND APPLICATION本标准规定了锂离子电池的定义、技术要求、测试方法及考前须知。

本标准适用于深圳市山伊克斯技术生产的锂离子电池。

This specification describes the definition, technical requirement, testing method, warning and caution of the lithium ion rechargeable battery. The specification only applies to battery supplied by Shenzhen 3EX TECH. Co., Ltd.2. 定义 DEFINITION2.1 额定容量:指在20±5℃,65±5%RH 环境下,以5小时率放电至终止电压时的容量,单位毫安时(mAh)。

Rated Capacity: Under 20±5℃,65±5%RH, it means the capacity value of being discharged by 5hrs ratio to End Voltage.2.2 终止电压:放电终止时的规定电压为2.75V 。

End voltage: The end voltage of discharge is 2.75V ,which is defined specially.2.3 0.2倍率充电:指在20±5℃,65±5%RH 环境下,以140mA 电流恒流充电至单体电池电压4.2V 后,转为恒压4.2V 充电,至充电电流小于10±5mA ,停止充电。

  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。

锂离子电池规格书SpecificationForLithium Ion Rechargeable Battery电池型号(Type):383450AH标称容量(Rated Capacity):700mAh部门(Department):铝壳制造部生效日期(Effective Date):2007-3-121. 范围SCOPE AND APPLICATION本标准规定了锂离子电池的定义、技术要求、测试方法及注意事项。

本标准适用于深圳市山伊克斯技术有限公司生产的锂离子电池。

This specification describes the definition, technical requirement, testing method, warning and caution of the lithium ion rechargeable battery. The specification only applies to battery supplied by Shenzhen 3EX TECH. Co., Ltd.2. 定义 DEFINITION2.1 额定容量:指在20±5℃,65±5%RH 环境下,以5小时率放电至终止电压时的容量,单位毫安时(mAh)。

Rated Capacity: Under 20±5℃,65±5%RH, it means the capacity value of being discharged by 5hrs ratio to End Voltage.2.2 终止电压:放电终止时的规定电压为2.75V 。

End voltage: The end voltage of discharge is 2.75V ,which is defined specially.2.3 0.2倍率充电:指在20±5℃,65±5%RH 环境下,以140mA 电流恒流充电至单体电池电压4.2V 后,转为恒压4.2V 充电,至充电电流小于10±5mA ,停止充电。

0.2 Charge method: Under 20±5℃,65±5%RH, it can be charged to 4.2V with constant current of 140mA, and then, charged continuously with constant voltage of 4.2V until the charged current is less than 10±5mA.2.4 0.5倍率充电:指在20±5℃,65±5%RH 环境下,以350mA 电流恒流充电至单体电池电压4.2V 后,转为恒压4.2V 充电,至充电电流小于10±5mA ,停止充电。

0.5 Charge method: Under 20±5℃,65±5%RH, it can be charged to 4.2V with constant current of 350mA, and then, charged continuously with constant voltage of 4.2V until the charged current is less than 10±5mA.2.5 1倍率充电:指在20±5℃,65±5%RH 环境下,以700mA 电流恒流充电至单体电池电压4.2V 后,转为恒压4.2V 充电,至充电电流小于10±5mA ,停止充电。

1 Charge Method: Under 20±5℃,65±5%RH, it can be charged to 4.2V with constant current of 700mA, and then, charged continuously with constant voltage of 4.2V until the charged current is less than 10±5mA.2.6 0.2倍率放电:指在20±5℃,65±5%RH 环境下,以140mA 电流恒流放电至单体电池电压2.75V 。

0.2 Discharge Method: Under 20±5℃,65±5%RH, it can be discharged to the voltage of 2.75V with constant current of 140mA.2.7 0.5倍率放电:指在20±5℃,65±5%RH 环境下,以350mA 电流恒流放电至单体电池电压2.75V 。

0.5 Discharge Method: Under 20±5℃,65±5%RH, it can be discharged to the voltage of 2.75V with constant current of 350mA.2.8 1倍率放电:指在20±5℃,65±5%RH 环境下,以700mA 电流恒流放电至单体电池电压2.75V 。

1 Discharge Method: Under 20±5℃,65±5%RH, it can be discharged to the voltage of 2.75V with constant current 700mA.3 外形尺寸 SHAPE AND PHYSICAL DIMENSION3.1 产品的命名 Naming Instruction of Product 3EX ———— 38 34 50 AH厂名 ———— 壳厚 宽度 高度 特殊性能Manufacturing Plant Diameter Length Special Property3.2 电池尺寸4.1+0 -0.3×33.8+0 -0.5×50.0+0 -0.5 mm4 结构 STRUCTION电池由正极片、负极片、隔膜、电解液、外壳等组成。

The battery consists of the positive electrode, negative electrode, separator, electrolyte and crust. 5 技术要求 TECHNICAL REQUIREMENT5.1 使用环境 Usage Conditions充电温度 Charging Temperature:0~45℃放电温度Discharging Temperature: -20~60℃相对湿度Related Humidity:<93℃大气压力Atmospheric Pressure: 86~106Kpa5.2 外观:无破裂、划痕、变形、污迹、电解液泄露。

Appearance: Without break, scratch, distortion, contamination and leakage.5.3 额定容量Rated Capacity: 650mAh5.4 内阻Internal resistance: <60mΩ (AC Impedance, 1000Hz)5.5 开路电压Open Voltage: 3.75V5.6 电性能Electronic Performance5.6.1容量-温度性能Capacity-Temperature Performance电池在表1规定不同温度下放电。

每一温度下电池容量同25℃下电池容量相比较,计算百分比,每只电池应达到或超过表1中的对应指标。

The battery discharges at different temperatures listed in Table 1. Discharge capacity of the battery at different temperatures compares with that of 25℃respectively, the percentage calculated will meet or above the requirement of Table 1.电池进行充放电循环300次后,电池剩余容量应大于初始容量的80%。

After the battery had 300 charge-discharge cycles, residual capacity of the battery will be above 80% of initial capacity.5.6.3储存性能Storage Performance5.6.3.1存储后的残余容量Residual Capacity After Storage电池充放电后,不同温度存储不同时间,计算电池的百分比剩余容量必须达到表2中对应的指标。

temperatures, residual capacity after storage calculated will meet or above the requirement of Table 2.Table 25.7.1 恒定湿热性能:测试后电池的容量必须达到初始的80%以上;内阻应该低于120mΩ;无电解液泄漏,无生锈,标识清晰可辩。

Static Humidity: The cell capacity shall be at least 80% of the original capacity and the impedance shall be less than 120mΩ. There shall be no electrolyte leakage. There shall be no rusting. Part marking must be legible.5.7.2 振动:测试后内阻小于120mΩ;电解液无泄漏。

Vibration: The cell impedance shall be less than 120mΩ. There shall be no electrolyte leakage. 5.7.3 机械冲击:测试后电解液无泄漏。

Mechanical Shock: There shall be no electrolyte leakage.5.7.4 温度冲击性能:测试后内阻小于120mΩ;电解液无泄漏。

Temperature Shock: The cell impedance shall be less than 120mΩ. There shall be no electrolyte leakage.5.8 安全性能Safety Characteristic5.8.1 过充测试:测试后电池不冒烟、不爆炸、不起火。

相关文档
最新文档