电梯行业专用英语完整版
电梯专业英语词汇
电梯专业英语词汇abbreviation 缩语abnormal "不正常的,反常的" abnormality monitoring 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期，扫描循环acceleration control system 加速度控制系统acceleration(accel)rate 加速器accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch "通道开关,维修用开关"access way 进出通道accessibility "可通达性,接近的,难易程度"accessible 允许进入accessible space 允许进入的场地accessory "配件,附件"accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic "听觉的,声音的"acrew die 板牙activate "启动,触发"active mode 主动模式actual condition "实际状况,实际条件"actual load 实际载荷actual state 实际状况actual value 实际值actuate "开动,操作,激励"actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator "操纵机构,激励器,螺线管"actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压adaptation "适应,匹配"adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive control system 自适应能力控制系统addendum "齿顶高,附录"addendum circle 外圆adding working drawing 附加加工图addition "附加物,加法"additional materials 附加材料address 地址adhesion "胶,粘合胶"adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car "相邻轿厢,相邻电梯"adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动adjustable wrench "活动扳手,可调扳手"adjusting screw 调节螺丝adjustor 调试员administation overjhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced "提前的,先进的"advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值aerial cableway "空中缆车,架空索道"aerial ropeway "空中缆车,架空索道"aerial tramway "空中缆车,架空索道"aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土alcove arrangement 电梯U型排列法algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation "分配,分派"allocation of landing call 层站呼梯指令分配allowance "允用误差,加工余量"allowble stress for temporary load 允许暂时应力值alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage "锚具,锚定"angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator "报音器,声音合成器"anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen power 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour "轴,杆"arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm "臂,支路"armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape recording 磁带录音authority "当局,核准部门"authority of lift acceptance 电梯验收部门authorized "授权的,核准的"authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯)back side "后侧,后边"back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank "银行,群组,排"bar "条,棒"bar code 条形码bar lock 杆式锁bare wire 裸线barricade "防护墙,隔墙"barrier "隔板,栅栏"base "基座,基础"base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias "偏置,偏移"bid "投标,报价"bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binary 二进制binder 装订册bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade "叶片,刀片,锯片"blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole "钻孔,镗孔"boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙bottom counterweight overtravel 轿底对重越程bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box "盒,箱"box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press "折弯机,压弯机"brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break "切断,破断"break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken step safety device 梯级破列安全装置broken tape sweitch 短带开关bronze 铜brunching "成组,成群"brush finished stainless steel 哑光不锈钢brush holder "刷握,滑环"brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行buried 埋入的burn in (程序)灌入burr "毛刺,毛边"burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing "衬套,轴套,套筒"butt joint "平接,对焊"button 按钮button switch 按钮开关buyer 买方buzzer 蜂鸣器buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab "轿厢,座舱"cab interior 轿厢内部cabin "轿厢,座舱"cabinet "柜,厢"cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call "呼梯,呼叫"call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contrl 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call load 呼梯输入call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel "撤消,取消"cancelingof call signal 呼梯信号消除cancellation "撤消,取消"canopy "顶盖,大蓬"canvas 帆布canvas hose 帆布软管cap "帽,盖子"cap nut 螺母capacitance "电容,电容量"capacitor 电容capacitor motor 电容器电机capacity "载重,容量,定员"capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment "轿厢调度,轿厢分配"car automatic switch landing 轿厢开关自动停站car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom overtravel 轿厢底部越层car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit "轿厢安全门,应急门"car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior "轿厢外装修,轿厢外表"car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame "轿厢架,轿架"car frame "轿厢架,轿架"car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car front 轿厢前壁car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control "手柄开关操纵,轿内开关控制"car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel "轿厢照明板,照明天花板"car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel with window 轿厢壁板上窗口car platform "轿厢底,轿底"car platform guard 轿厢站台护板car platform sill 轿厢car position indicator "轿厢指示灯,轿厢位置显示"car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof "轿厢顶,轿顶"car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯)car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling "轿厢架,吊架"car station 轿厢操纵站car status information 轿厢运行状态信息car stop 轿厢停止car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置car switch control 轿厢开关控制car switch opration "手柄开关操纵,轿内开关控制"car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit "轿顶安全出口,轿顶应急出口"car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls "轿厢壁,轿壁"car weight 轿厢重量car width 轿厢宽度carbon "碳,石墨"carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card "卡片,纹板"card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency "载波频率,开关工作频率"carrying capacity "载运量,载运能力"cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade "级联,串联"cascade sub-loop 串接式子回路case "箱,盒,外壳"casing "保护套,外套"casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢casting 铸造castor oil 蓖麻油catch "擎子,门扣,捕捉器"catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation "气穴,涡穴,饱和压力点"ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement "水泥,胶合剂"cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门center plunger hydraulic lift 柱塞直顶式液压电梯center support "中心支撑,中间支撑,第三支撑" center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centrifugal 离心的centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive 链传动chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link "链节,链环"chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机chain tensioning device 链张紧装置chain wheel 链轮chain wheel track 链轮导轨chamger "倒棱,去毛刺"change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character "特征,字符" characteristic "特征,特性" characteristic curve 特性曲线charge "充电,收费"charged "带电,充电"charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke "扼流,截流,阻塞"choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价cinder concrete 煤渣混凝土circle "周期,圆"circuit 电路circuit breaker "断电器,断路器" circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring "压制环,加紧环" clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度cleated riser 梯级竖板clerance 间隙clevis U型夹client "客户,买主"clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing travel 门关闭运行closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code "码,符号,规程,规范"code of practice "实施规程,实用规程"code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil "线圈,绕组"coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate "栅栏门,折叠式门"collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection "收集,集合"collective control 集中控制collective full automatic operation 全自动集中控制collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column "柱,立柱"comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment "隔板,隔室"compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent "有资格的,胜任的"competent personnel "有资格的人员,胜任的人员"competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract "综合维修合同,全包维修合同" comprehensive service contract "综合维修合同,全包维修合同" compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed "隐蔽的,暗式"concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod "连杆,连接杆"connection 连接connection diagram of controller 控制柜连线图connector "接线柱,连接器"conract specification "合同规定,合同明细表"conract speed "合同速度,额定速度"consecutively departing 依次派出的轿厢console panel "控制柜,控制盘"constant "恒定的,常数"constant HP motor 功率恒定型电机constant speed valve "比例控制阀,调速阀"constant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layout drawing 土建图construction platform "安装平台,施工平台" construction site "安装工地,施工工地"consultant "顾问,咨询机构"consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger "接触指,滑触头"contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract "合同,契约,承包合同"contract capacity "合同载重量,合同容量"contract load 合同负载contract of indemnity 赔偿合同contract party "合同方,合同当事人"contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置control feature 控制特征control gear 控制论control guard for handrail breakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage "控制电压,操作电压"controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter "整流器,转换头"converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord "绳索,芯线"cord drive "绳传动,(厅门)"core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner "角,隔"corner post 对角立柱corpus lift 尸体升降机correct phase sequence 正确相序correcting "修正,校正"correcting travel 校准运行correction "校正,校准"corrective maintenance 校正维修corridor 走廊corrosion proof 防腐蚀的corrosion resistant 耐腐蚀的corrosion resistant coating 涂防锈漆层corrosive 腐蚀的cost "成本,费用"cost accounting 成倍核算cost analysis 成本分析cost calculation 成倍计算cost comparison 成本比较cost effective 价格划算的cost element 成本项目cost estimate 成本估算cost of material 材料成本cost of production 生产成本。
电梯专业词汇的中英对照
access door检修门
access forbidden禁止入内
access lift通道电梯
access security通道防卫
access switch "通道开关,维修用开关"
access way进出通道
accessibility "可通达性,接近的,难易程度"
aluminum cladding铝制包层
alumite防蚀铝
alundum氧化铝
ambient环境的
ambient noise环境噪音
ambient temperature环境温度
ammeter安培计
ammonia氨
amperage电流强度
ampere安培
amplification放大
amplification stage放大等级
ANSI(America Nationa Standard Instirute)美国国家标准协会
anti-clockwise逆时钟方向
anti-corrosive paint防腐蚀漆
anti-creep防蠕动
anti-friction bearing抗摩擦轴承
anti-nuisance防干扰
anti-nuisance device防捣乱装置
anti-rust防锈
anti-stall防空转
anti-vibralion pad防震垫
APM(automatic people mover)自动人员运输机
apparen power视在功率
apparent output视在输出
applicant申请人
application申请
电梯专业英语
lock washer(L/W) 斜垫片 lockable 可闭锁的，可锁定的 locker 摇杆，锁紧器 lock-in circuit 自保电路 locking jaw 锁紧爪 locking relay 自锁继电器 locks 门锁装置，联锁装置 log diary 运行日记 logger 记录器 logic analyser 逻辑分析器 logic circuit 逻辑电路 logic diagram 逻辑图 logic element 逻辑元件 logical combination 逻辑结合 long ton 长吨，英制吨 long wait hall call 候梯时间较长的门厅呼梯 long wait landing call 候梯时间较长的层站呼梯 longitudinal 纵向的 Long's lay rope 同向捻（顺捻）钢丝绳loop 环圈 loop circuit 环形电路 loop current 环流 loose bearing 松配轴承 loose fit 动配合 loss 损耗 loss of power 功率损耗 loudness level 响度 louver 气窗 low carbon steel 低碳钢 low cost 低成本的，廉价的 low rise building 低层建筑物 low speed 低速的，慢速的 low speed winding 低速绕组 lower chord 下楔材料 lower cost solution 低成本方案 lower frame 底部框架 lower/upper landing （自动扶梯）下部/上部通道 lowest call reversal(LCR) 最低层呼梯反向 lowest reversal floor 最低反向楼层 low-rise lift group 低层区电梯组群 low-rise zone 低层区 low-speed door 低速门 LS(limit switch) bracket 限位开关支架 LS(limit switch) cam 限位开关碰铁 lubricant 润滑剂 lubricating fitting 润滑装置 lubricating instructions 润滑说明书 lubrication 润滑 lubrication ring 润滑油杯 lubricator 润滑器 lug 线桥 luggage lift 行李电梯 lumen 流明（光通量单位）luminous indicator 发光指示器 Lux 勒克司（照明单位） machinability 切削性machine 曳引机 machine beam 曳引机承重钢梁 machine beam plate 曳引机支撑板machine bed 曳引机座 machine bed inserting mortar 曳引机座（砂浆）灌缝 machine bed plate 机器底板，曳引机底板 machine driving 曳引机 machine earthquake proof stopper 曳引机防震挡止器 machine elevation device 曳引机高度调整装置 machine frame 曳引机架 machine installation 曳引机安装 machine isolation 曳引机隔震machine isolation device 曳引机隔震装置 machine language 机器语言 machine No. plate 曳引机编号牌 machine room 机房 machine room area 机房面积 machine room arrangement 机房布置 machine room depth 机房深度 machine room height 机房高度machine room inspection 机房检修 machine room lower 下机房 machine room of hydraulic lift 液压电梯机房 machine room plan 机房布置图 machine room upper 上机房 machine room width 机房宽度 machine room wiring harness 机房配线束 machine sheave cover 曳引机绳轮罩 machine spacing bed 曳引机高度调整底座 machine sprocket 曳引机链轮 machine supporing steels 曳引机承重钢楔 machine supporting beams 承重梁 machine supporting steelwork 曳引机承重钢结构 machine tools 机床machined 机加工的 machinery 机械 machining 机械加工 machining allowance 加工余量 machining in general 普通机械加工 magnet 磁条 magnet brake 磁力制动器 magnet coil 电磁线圈 magnet lamination 电磁铁芯片 magnet plunger 插棒式电磁 magnet vane 隔磁板 magnetic amplifier 磁放大器 magnetic brake 电磁制动器 magnetic catch 磁闩magnetic charateristic 磁特性 magnetic clutch 磁性离合器 magnetic detector 磁力检查器 magnetic flux 磁通量 magnetic flux density 磁通密度 magnetic leveling switch 磁性离合开关 magnetic noise 电磁噪声 magnetic pole 磁极 magnetic resistance 磁阻magnetic switch 磁感应开关 magnetism 磁性 magnetism pole 磁棒 magnitude 大小，数量，等级 magntic core 磁铁芯 mahogany 红木 main chain 主链条 main circuit 主电路 main circuit breaker 主断路器 main circuit control 主电路控制 main contact 主触点main contactor 主接触器 main drive 主驱动装置 main drive chain 主驱动链 main drive chain guard 主驱动链保护装置 main drive shaft 主驱动轴 main drive sprocket 主驱动链轮 main drive wheel 主驱动装置 main drive wheel 主驱动轮 main floor 基站 main landing 基站 main landing door switch 基站门开关 main lobby 大厅，主厅 main menu 主菜单 main power 主电源 main program 主程序 main reservoir 油箱 main rope 主钢丝绳 main stop 基站 main switch 总开关 main valve 主阀门 main-drive assembly 主驱动总成，主驱动部件 maintenance contract 维修合同 maintenance control 检修控制maintenance cost 维修成本 maintenance fitter 维修保养工 maintenance instruction 维修说明书 maintenance man 维修人员 maintenance operation 维修作业 maintenance-free 免费维修 make contact 触点闭合 maker's name plate 制造商铭牌 making button 动合按钮 male guie rail 雄导轨，带凸榫导轨 malfunction 误动作，失灵，不正常工作mallet 木槌 managanese bronze 锰青铜 mandatory 强制的 manganese 锰 manhole 人孔man-hour coutput 人小时产量 manipulation 利用，操纵 manipulator 操纵器，机械手man-made fiber 人造纤维 manometer 压力计 mansion 大厦 manual brake release 手动松闸装置 manual lowering valve 手动下降阀 manual opened door 手动门 manual opened hoistway door 手动厅门 manual tune 人工调节，手动调节 manual type of control 手动控制 manual wheel 盘车手轮 manualemergency operating device 手动应急操作装置 manually operated down valve 手动下降阀 manualy operated door 手动门manufacture 制造，生产 manufacturer 生产者 manufacturing and sales release 生产和销售许可通知 manufacturing release 生产许可通知 manufacturing tolerance 制造公差maple 枫木 margin 极限，边界，范围 marginal condition 边缘条件 marine elevator 船用电梯 market concept 市场观念 market position 市场地位 market report 市场报告market share 市场占有率 masonry wall 转砌墙 masonry well 砖砌井道 mass 质量，块，团，大量的 mass monent of inertia 惯性矩 mass production 大量生产 master 主任，硕士，主导的，精通的 master PC board 主印数电路板 master station 总站master/slave method 主/从方法，防效方法 mat 垫块，罩面 mat switch 罩面开关matching 匹配 materia overhead 材料管理费 material 材料 material handling 材料搬运material supply planning 材料供应计划 matted design 闷光图案 maximum 最大的maximum capacity 最大容量，最大能力 maximum clear opening 最大净开口maximum load 最大载荷 maximum speed 最高速度 maximum waiting queue 最大候梯乘客量 maximum waiting time 最长候梯时间 mean square 均方 mean value 平均值，有效值〕 mean velocity 平均速度 means 方法，装置 measured load 测定值 measuring instrument 测量仪表 measuring meter 测量计 measuring range 测量范围 measuring unit 计量单位〕 mechanic 钳工 mechanical brake 机械式制动器 mechanical car position indicator 机械式轿厢位置指示器 mechanical door interlock 门机械联锁装置mechanical door safety 机械式门安全装置 mechanical efficiency 机械效率 mechanical lock 机械式锁 mechanical reopening device 机械式重开门装置 mechanical safety shoe 机械式安全触板 mechanical switch 机械开关 mechanism switch 机器开关 mechanized parking garage equitment 机械化停车库设备 medium duty traffic 中级负荷交通medium speed 中速，单层运行最高速 megger 兆欧表，高阻表，摇表 megohm 兆欧姆 melting point 融化点 member 部件 memorandum 备忘录 memory 记忆装置memory address 存储地址 memory location 存储位置 menu 菜单 mercury 汞，水银mercury arc 汞弧 mercury switch 水银开关 mercury vapor rectifier 汞气整流器mercury vapour 水银蒸汽，汞气 mercuryarc rectifier 汞弧整流器 mercury-wetted relay 水银湿润继电器 merit 优点，指标 mesh 网 meshed 网式的 meshed design 网状图案metal 金属 metal section 金属型材 metallic shim 金属垫片 meter 计量器，仪表，米，公尺 meter-in circuit 电路仪表 metering valve 计量阀 method 方式，方法 metric 公制metric graduation 公（米）制刻度 metric ton 公吨 MG(motor generator) 电动机发电机组 MG(motor generator) set 电动机发电机组 mian terminal 大端子 mians 电力网mians current 馈路电流 mians voltage fluctuation 电源电压波动 miantainer 维修工，维修人员 miantenance 维修，保养 miantenance agreement 维修协议 micro limit switch 微动限位开关 microampere 微安培 micro-computer 微型计算机microcontroller 微型控制器 microfarad 微法 microfilm punched card 微缩胶片冲孔卡micro-processor 微处理器，微机 microprodessor opertation control 微处理机操作控制micro-switch 微动开关 microvolt 微伏 middle conductor 中线段 middle speed elevator 中速电梯 midpoint 中间 mid-rise building 中层建筑物，中高度建筑物 mild steel 软（低碳）钢 mileage recorder （电梯）运行次数记录器 mill 铣削，轧钢机（厂）milliampere 毫安培 millimeter 毫米 milling cutter 铣刀 milling machine 铣床 millivolt 毫伏特 mine lift 矿井电梯 mineral cotton 矿物棉 mineral fiber 矿物纤维 mineral wool 矿物毛 minus 负极，负数 minute 分钟 mirror 镜子 mirror finish 镜面抛光，镜面加工mirror finished stainless steel 镜面不锈钢 mirror-inverted 对影像的 miscellaneous 杂项的，其他的 mixing 混合 mode casting mill 铸模车床 mode of supplly 供货方式modem 调制解调器 modern 现代的 modernization 现代化，（电梯）更新改造modernization overlay 全面改造，全面现代化 modification 修改 modifier 调节器modular 组模式，组合式 modular concept 组模化原理 modular escalatot 多坡度（组合式）自动扶梯 modular system 组模系统 modular unit 组模单元 modulation 调制解调器 module （集成电路）组件，继电器，固态继电器 modulus 模数 modulus of elasticity 弹性模数 modulus of longitudinal elasticity 纵向弹性模数 modulus of transverse elasticity 横向弹性模数 moisture 湿度 moisture proof 防潮的 molding 壁板缝压板，模压 molybdenum 钼 moment （力，弯，转）矩 moment of inertia 惯性矩momentary pressure 瞬时的 moniflop 单稳态触发器 monitor 监视，监控，检测monitor panel 梯群监控盘 monitor program 监控程序 monitoring 监视，监控，检测monitoring contact 监控触点 monitoring device 监测装置，监控装置 monkey wrench 活动扳手 mono 单一的 monochrome 单色的 mono-mass safety 单件安全装置monostable circuit 单稳态电路 mon-preformed rope 松散绳 mortuary lift 殡仪馆电梯，太平间电梯 MOS(metal oxide-semiconductor) 金属氧化物半导体 MOS(metal oxide-silicon) 金属氧化物硅 motion 运动 motion control 拖动控制 motion speed 运行速度 motor 电动机，马达 motor base frequency 电机频率 motor base speed 电动机额定速度 motor capacity 电机功率 motor drive unit 电机驱动装置 motor fan 电动机（冷却）风扇 motor field excitation switch 电动机磁场激励开关 motor handle 盘车手轮motor pulley 电机皮带轮 motor rated sped 电动机额定速度 motor shield 电机端罩motor testing stand 电机试验台 motor vehicle lift 汽车电梯 motoring condition 电动状态 moulding 模压，模制零件，制模 mounting bracker 固定架 mounting plate 固定板mouse 鼠，鼠标 movable cam 可动凸轮，可动碰铁 movable car platform 活动轿厢底盘 moving coil motor 动圈式电动机 moving contact 活动触点 moving walk 自动人行道 muffler 消音器 mullti-conductor cable 多线电缆 multi-core cable 多芯电缆 multi-funtion 多功能的 multi-group 多组群（电梯） multi-leaf door 多扇门 multi-leaf sliding door 多扇滑动门 multi-panel sliding door 多扇滑动门 multiple 多重的 multiple elevator hoistway 多电梯井道 multiple floor flight time 多层运行时间 multiple leaf door 多扇门 multiple roping(multi-roping) 多线悬挂的 multiple tenancy building 多个承用者大楼 "multiple thread wor," 多螺纹蜗杆 multiple well 多梯井道 multiple wire plug connection 多线插接 multiple-floor run 多层运行时间 multiplex down-collective automatic operation 多层下集选全自动控制 multiplying pulley 倍增滑轮 multi-plywood 多层胶合板 multipoint connector strip(pcb) 插式接头板（印刷电路板）multi-program 多程序系统 multi-roped lift 多绳悬挂电梯 multi-section door 多扇门multi-speed driving 多速驱动系统 multi-speed starting 多速起动 multi-stage jack 多段式液压升降装置 multi-stage ram 多段式柱塞 multi-start worm 多头蜗杆 multi-storey flat 多层公寓 multi-story building 多层建筑物 multi-stpreu apartment house 多层公寓multi-use 多用途的 multi-voltage control 多极电压控制 multi-way stitch 多路开关multi-wire cable 多线电缆 munsell color system 蒙塞尔色调 mutation 转变，更换N.C.(normal closed ) contact 常闭触点 N.O.(normal open) contact 常开触点 nameplate 铭牌 nameplate current 铭牌电流，额定电流 NAND gate 非与门 narrow door jamb 小门套，窄门套 national codes 国家标准 national regulation 国家规定 natural fiber 天然纤维 natural frequency 固有频率 natural lighting 自然照明 natural period 固有周期natural ventilation 自然通风 nbuilder's work 土建工程 neck of axle 轴颈 needle 针needle bearing 滚针轴承 needle cage 针罩 needle point pliers 尖嘴钳 negative 负电negligible 可忽略的 neon glow 氖辉光管 neon lamp 霓虹灯 neoprene 合成橡胶 net 网络，净值，有效的 net car floor area 轿厢地板净面积 net section 有效截面 neuron network 神经网络 neutral conductor 中性线 neutral earthing 中性接地 neutral grounding 中性接地 neutral point 中性点 neutral position 中性位置 newel 中性，楼梯扶栏柱 newel stand 中柱台 nib 牛腿，凸边 nickel 镍 nickel chromium molybdenum steel 镍铬钼钢 nickel molybdenum steel 镍钼钢 nickel steel 镍钢 night traffic 夜间交通no load test 空载实验 noise 噪声 noise insulation 隔音 noise level 噪声电平，干扰电平 noise proof 隔音 noise protction 噪声防护 noise reduced 减噪声的 noise suppression 消音的 no-load current 空载电流 no-load operation 空载操作 no-load running No. of poles 空载运行极对数 nomenclature 术语，命名 nominal 标定的 nominal diameter 标称直径 nominal dimension 公称尺寸 nominal spedd of up motion 上行额定速度nominal speed of down motion 下行额定速度 nominal tensile strength 标称抗拉强度nominal torque 额定扭矩 nominal-data 额定数据 non-combustible 不易燃的 non-combustible material 不可燃材料 non-contact electronic door safety sensor 不接触电子传感式门安全装置 none return valve 单向阀 non-ferrous 非铁的 non-flammable 不可燃的 non-magnetic shield 隔磁屏 non-metallic 非金属的 non-reversing device 防逆转装置，防反向装置 non-selective collective automatic operation 非集选自动控制 non-stop 无停站 non-stop button 直驶按钮 non-stop switch 直驶开关 non-volatile(NV) memory 非易失性存储器 noon peak 午间交通高峰 noon traffic mode 午间交通 NOR circuit 非或电路 NOR gate 非或门 normal bend coupling 普通管接头联轴器 normal illumination 正常照明 normal limit switch 限位开关 normal position 正常位置 normal terminal stopping switch 终端常位停车开关 normal travel 正常运行 normalizing 正常化 normally closed (N/C) 常闭的 normally opened (N/O) 常开的 nose line 凸出线 nose of comb 梳齿端 nosing 牛腿 NOT circuit 非电路 NOT gate 非门 notch V型槽，V凹口 note 加注，说明 notice for use 使用须知 nudging 强迫关门 nuisance 捣乱 number of passenger 乘客人数 number of revolutions 转数 number of segment 换向片数number of slots 电机槽数 number of stops 停站数 number of turns 绕线匝数 numbering of elevator 电梯编号 nut 螺帽，螺母 nylon 尼龙 nylon lining 尼龙衬套 nylon tube 尼龙管 oak 橡木 object 物体 observation cab 观光轿厢 observation lift 观光电梯observatory lift 观光电梯 occupancy 占用，居住 occupant 占用者，居住者 occupants of building 大楼居住者，大楼住户 off peak 非高峰的，峰值外的 off position 断开位置 office building 办公大楼 off-peak traffic 非高峰交通状态 ohmmeter 欧姆计 oil 油oil brake 油压制动器 oil buffer 油压缓冲器，耗能型缓冲器 oil buffer switch 油压缓冲器开关 oil can 油壶 oil collector 集油器 oil cooler 油冷却器 oil deflector 挡油圈 oil dish 积油盘 oil drip pan 接油盘 oil filler pipe 充油管 oil film 油膜 oil filter 滤油器 oil gauge 油量表 oil immersed transformer 油浸式变压器 oil leakage 漏油 oil level 油位oil level gauge 油标，油位计 oil level indicator 油位指示器 oil pan 油盘 oil piping 油管 oil quench 油淬火 oil receiver 油盘 oil reservoir 油池 oil ring 油环 oil seal 油封 oil spray 油雾 oil sump gasket 油槽垫圈 oil tank 油箱 oil waste box 油渣盒 oil wick 油绳oil wiper ring 挡油环 oilier 给油器 oil-immersed 浸油的 oilless bearing 无油式轴承oil-proof 耐油的 oil-tight 油封 on inquiry 询问，询价 on-board delay 登梯延时，登梯后的等候时间 on-board delay in passenger seconds 登梯及等候时间 on-call control 呼梯控制 one floor run 单层运行 one hour rating 小时定额 one stage ram 一段式柱塞one way automatic leveling device 单向自动平层装置 one way restrictor 单向节流阀（液压梯） one-to-one rope 1:1 绕绳比 one-to-two rope 1:2 绕绳比 on-line 在线的，联机的 onlocking zone 开锁区域 on-site assistance 现场帮助 opal 乳白的 opaque 不透明的 opaque balustrade 不透明扶栏 open air type elevator 露天电梯 open circuit 断路open loop 开环控制 open type elevator 敞开式电梯 open-close switch 开关操纵器opened-type motor 敞开式电动机 open-end wrench 开口扳手 open-hearth steel 平炉钢opening angle 张角，开启角 opening direction 开启方向 operable 可操作的 operate 操作 operating button 操作按钮 operating cam 操作碰头 operating device 操作装置operating element 操作元件 operating instructions 操作说明书，使用说明书 operating magnet 操作磁铁 operating panel 操作盘 operating pressure 操作压力 operating range 操作范围，使用范围 operating voltage 操作电压，工作电压 operation 操作，运转，控制 operation panel 操纵箱，操纵盘 operation system 操作系统，操作方式operational amplifier 运算放大器 operational brake 操作制动器 operational reliability 操作可靠性 operative section 操作部分 operator 操作碰铁，司机 opposed access door两面开门 opposing arrangement 对面布置 opposing automatic doors 贯通式自动门opposite car entrance 贯通式轿厢出入口 opposite door 贯通式门 opposite entrance 贯通式出入门 opsition dependent 按位置 opsition detector 位置检查器 opsition deviation 位置偏差 optical 光学的 optical fiber 光导纤维 optical fiber cable 光缆，光导纤维电缆 optical indicator 发光指示器 optical signal 发光信号 optical-fiber communication 光导纤维通讯 optional 可选择的 optional specification supervision 可选规格管理 opto-coupler 光电耦合 optoelectronic 光电耦合 OR circuit 或电路 OR gate 或门 order 订单，订货单，次序 order processing 合同（订单）处理 ordering documentation 订货文件 ordering instruction 订货说明书 ordinary lay 普通绳股 ordinary lay rope 普通捻股钢丝绳 ordinary lift 一般用电梯 orifice 节流孔，阻尼孔 original 原装的，原件，原图 original package 原包装 O-ring O型圈 ornamental-patterned surface 装饰花纹表面 oscillator 示波器 oscillograph 示波器 oscilloscope 示波器 oscillosynchroscope 同步示波器 out door use escalator 户外自动扶梯 out of balance load 不均衡负载 out of phase 相移 out of phase 180°相移180° out of phase 90°相移90° out of service 故障，停止运行 out of stock 无现货 outer deck 外侧盖板 outer ledge 外侧边缘 outer ledge bracket 外侧架支架 outer panel 外侧板 outer pipe 出口管 outer sheathing 外套 outlet 插座，引线，出口 outline 轮廓，外形 outling of truss 框架外形 output 输出 output current 输出电流 output signal 输出信号 output torque 输出扭矩 output voltage 输出电压 outside 外面，外边 outside diameter 外径 oval 椭圆形 over balance 超平衡 over driven worm gear 蜗杆在上方的蜗轮蜗杆传动 over heating 过热 over power 过负载over run 超程 over sling 上吊架 over slung type 上悬吊式 over speed switch 超速开关overall cost 总成本，总费用 overcurrent 过电流 overcurrent relay 过流继电器overcurrent release 过电流释放 overcurrent vreaker 过流断路器 overhang 悬臂式，外伸的 overhang traction sheave 悬臂式曳引轮 overhaul 大修 overhead 顶层空间，顶部overhead beam 顶楔 overhead height 顶层高度，顶部高度 overhead machine 顶置曳引机 overhead pulley 顶部轮 overhead sheave 顶部绳轮 overhead structure 顶部构件overhead(O/H) 顶房上置 overhoisting limit switch 井道上部限位开关 overlap 重叠overlay （墙壁等）饰面 overload 超载 overload buzzer 超载蜂鸣器 overload control 超载控制 overload device 超载装置 overload indicator 超载装置 overload lamp 超载灯overload test 超载试验 overload warning 超载报警 overload weighting microswitch 超载微动开关 overrun 越程 overshoot 过冲，速度调节过量 oversize 大号，超大号oversize reamer bolt 大号螺栓 overslung car 上方悬臂轿厢 overspeed 超速 overspeed governor 限速器 overspeed governor switch 超速保护装置 overtravel 越层 overturn moment 倾倒力矩 overturn-proof 房倾倒装置 overweight 超重 over-wind protection switch 防过卷开关 owner 物主，所有者 oxidate 氧化 p.c. motherboard 印刷电路母板package part 零件组合 packaging material 包装材料 packed landing bolt 门厅用配套螺栓 packing 包装 packing charge 包装费用 packing cost 包装成本 packing ring 密封环pad 衬垫，垫片 paddle fan 叶片式通风扇 paging service 传呼服务 paint 油漆 painting 涂漆，涂装 pale 踏板 pallet type moving walking 平板式自动扶梯 pallets 踏板 pan 盘panel 板，扇，屏 panel door 板式门 panorama lift 观光电梯 panoramic lift 观光电梯pantagraph 壁杆 pantagraph type hydraulic elevator 壁杆式液压梯 paraffin 煤油，石蜡parallel 并联 parallel circuit 并联电路 parallel continuous arrangement 并列设置parallel key 平键 parallel lay rope 平行捻钢丝绳 parameter 参数 parapet 防护栏杆parasitic signal 寄生信号 parking 驻停 parking car 驻停轿厢 parking device 停靠装置parking floor 驻停楼层 parking landing 驻停层站 parking signal light 驻停信号灯parking switch 驻停开关 parking zone 驻停区 part 零件 part for jamb and sill installation 门套和门坎安装用零件 partial load 部分载荷 partial view 局部视图partition 分隔，隔板 parts for closer installation 关门机安装用零件 parts layout 零件配置图 parts list 零件清单 pass button 直驶按钮，不停按钮 pass switch 不停开关，直驶开关 passage way 通道 passenger 乘客 passenger access time 乘客登梯时间passenger arrival rate 乘客到站率 passenger car 载客轿厢 passenger carried per minute 每分钟载运乘客人数 passenger conveyor 自动人行道 passenger exit time 乘客出梯时间 passenger journey time 乘客乘梯时间 passenger lift 乘客电梯 passenger loading time 乘客进入电梯时间 passenger transfer time 乘客进出电梯时间 passenger transit time 乘客转乘电梯时间 passenger transported per minute 每分钟载运乘客人数passenger unloading time 乘客走出电梯时间 passenger waiting time 乘客候梯时间passenger way 走道 passenger/freight elevator 客货两用电梯 passenger-and-freight elevator 客货两用电梯 passenger-goods lift 客货电梯 passing chime 到站钟 passive mode 被动模式 password 通行令，口令 patent 专利 patenting 线材（拉后退火）paternoster 链斗式升降机 pattern 图形 pavement lift 自动人行道 pawl 棘爪 PC board 印刷电路板 PCB (printed circuit board) 印刷电路板 PCB assembly frame 印刷电路板组装架 PCB bay 印刷电路板抽屉盒 PCB connection strip 印刷电路板插接条 PCB edge connector 印刷电路板边缘插接器 PCB plug-in check 印刷电路板插接通电检查PCB rack 印刷电路板插架 peak current 峰值电流 peak load 高峰负载 peak service 高峰交通服务 peak value 峰值 pedestal bearing 托架轴承 pension fund 退休基金，养老基金 penthouse 楼顶机房 pentode 五极管 perambulator 手推车 percenage 百分比percentage load 负载百分比 performance 性能 performance characteristic 性能特征performance curve 性能曲线 performance guaranteed maintenance 性能保证维修performance index 性能指标 performance test 性能试验 performed rope 预成型钢丝绳period of guarantee 担保期限 periodic maintenance 定期维修保养 periodic test 周期性试验，定期试验 periodical examination and test 定期检查和试验 periodical inspection 定期检查 peripheral 圆周的 peripheral force 圆周力，切线力 peripheral speed 圆周速度 periphery 圆周，圆柱体表面 permanent 永久 permanent magnet 永久性磁铁permeability 磁导率，渗透性 permissible deviation 允差 permissible stress 许用应力permitted stress 许用应力 personal code 个人电码 petroleum 石油 PG (pulse generator) 脉冲发生器，编码器 PG constant 编码器解像度，编码器常数 PG size 编码器解像度，编码器常数 phase 相位 phase advance 相移超前 phase angle 相位角 phase angle control 相位角控制 phase difference 相位差 phase failure 断相 phase failure relay 断相保护继电器 phase lagging 相移延迟 phase lead 相移超前 phase loss 断相 phase monitoring relay 相位监控继电器 phase reversal 反相，相序逆转 phase reversal relay 换相继电器 phase reversed 反相 phase shifting 相移的，移相的 phone connector （通讯线）插头 phosphorus 含磷的 photo detector 光监测装置 photo eye 光电监测器photo switch 光电管开关 photocell switch 光电管开关 photo-coupler 光电耦合器photo-diode 光电二极管 photo-electric cell 光电管 photo-electric device 光电管装置photo-electric passenger detector 光电乘客监测器 photo-electric protection 光电保护photo-electric safety device 光电保护装置 photo-electric switch 光电开关 pick-up （继电器）吸合，得到信号 picture plane display 画面显示 PID (proportional-integral-differential) 比例－积分－微分 piece rate 计件单价 piece wages 计件工资 piercing 冲孔 pillow block 架座 pilot light 指示灯 pilot production 试生产 pilot valve 导向阀 pin 销钉 pin adaptor 插头转接器 pincer 钳子 pine 松木 pinion 小齿轮，齿节 pipe 管子pipe bend 弯管 pipe clamp 管箍 pipe connection 导管连接 pipe fitting 管道配件 pipe rapture valve 管道破裂保险阀 pipe system 管道系统 pipe threading 管螺纹 pipeline 管道 piping 配管，管路 piston 活塞，柱塞 piston type cylinder 柱塞式油缸 pit 底坑 pit access door 底坑检修门 pit access ladder 底坑出入爬梯 pit depth 底坑深度 pit ladder 底坑爬梯 pit lamp 底坑灯 pit protection railing 底坑保护栅栏 pit ptotection gred 底坑护栏 pit safe plate 底坑安全板 pit screen 底坑防护网 pit stop switch 底坑停止开关 pit switch 底坑开关 pit tanking 底坑防水层 pitch 螺距 pitch circle 齿节 pitch diameter 节径 pitch line 节距 pitch of teeth 齿节距 pivot pin 中心销钉 pivot point 支点 pivoted guuide shoe 活动导靴 plain bearing 滑动轴承 plane 刨，刨平 planetary machine 行星齿轮机器 planing machine 刨床 plank （轿厢架）底楔 plastic foil 塑料薄膜 plastic materials 塑料材料 plastics 塑料 plate 板 plate counterweight 板式对重 plate glass 平板玻璃 plate spring 板簧 plate threshold 轿厢地坎 plated design 镀金图案 platform 轿厢底，轿底 platform frame （轿厢）底盘架 platform guard 轿厢站台护板 platform side brace 轿厢底侧拉条 platform sill 轿厢地坎 plating 电镀 PLC(programable logic controller) 可编程序控制器 PLD(programmable logic device) 可编程序逻辑器件 pliers 虎钳 pllug socket 插座 plug 插头转接器 plug connection 插塞连接 plug pin 插脚，插销 plug receptacle 插座 plugability 可插接性 plug-in module 插接式模块 plug-in type 插接式 plug-in unit 插接元件 plumb 铅垂侧直，铅垂 plumb bob 铅垂重物，铅垂plumb line 铅垂线 plunger 柱塞，插棒铁芯 plunger end-plate 柱塞端板 plunger head 柱塞顶部 plunger head sheave 柱塞顶部轮 plunger limit switch 柱塞限位开关 plunger return 柱塞复位 plunger runby 柱塞越程 plunger sheave 柱塞滑轮 plunger stopper 柱塞挡止器，柱塞防脱装置 plunger stroke 柱塞行程 plunger type cylinder 柱塞式液压缸 plus 加，正极 plyphase 多相 plywood 三合板，胶合板 pneumatic 气动的pneumatic door operator 气动开门机 point fo common connection (PCC) 普通接点pointer 指针 polarity 极性 pole 电极 pole coil 电极线圈 pole core 电极芯子 pole piece 极靴 pole shader 极帽 pole-changing 变换极性的 pole-piece lamination 极靴铁芯片polish 抛光 population 人口，人数 position 位置 position actual value 位置实际值position control 位置控制 position control loop 位置控制回路 position control system 位置控制系统 position controller 位置控制器 position feed-back loop 位置反馈回路position indicator 位置指示灯 position indicator of adjacent car 邻梯指层灯 position reference value 位置参照值 position reference value generator 位置参照值发生器position regulation 位置调节 position regulator 位置调节器 position scanner 位置扫描器 position sensor 位置传感器 position-dependent slowdown 按位置减速 positioningtrip 定位运行 positive 正电 positive connection 刚性连接 positive drive 强制驱动positive drive service lift 强制驱动杂物梯 positive operation 强制操作 post 柱 potential 电位，电势 potentiometer 电位计，电位器 pound 磅 power 功率，电源 power absorption 能量吸收 power amplification 功率放大 power amplifier 功率放大器 power consumption 功率消耗，电力消耗 power contactor 电源接触器 power converter 变流器 power current circuit 动力电路 power dissipation 功率消耗，电力消耗 power distribution panel 配电盘 power door 自动门 power door operation 电动门 power dumbwaiter 电动杂物梯 power factor 功率因素 power failure 停电，断电 power failure emergency operation 停电应急操作 power failure emergency service 停电应急服务 power input 功率输入 power loss 功率损失 power operated door 自动门 power operated truck 机动货车 power output 功率输出 power pack 电源装置 power range 功率范围 power source 电源 power supply 电源 power supply fluctuation 电源波动power supply line 供电线路 power supply unit 供电装置 power unit 电源装置 power up 通电，上电 powerwalk 自动人行道 PPR (pulse per revolution) 每转脉冲数，脉冲/转pre-announcing direction arrow 预告方向箭头 pre-assemble 预装置 precast concrete 预制混凝土 precautionary measure 安全措施 precondition 先决条件 pre-delivery 提前发货 predetermined landing 预定基站 pre-drill 预钻孔 preduction capacity 生产能力prefabricated 预制的 prefabricated concrete 预制混凝土 preference 优先权 preferential 优先的 preferential floor 优先楼层 preferential floor service 优先楼层服务 preferential landing 优先层站 preferential service 优先服务 preferred number 优选数字 pre-formed groove 预制槽 preliminary construction work 土建准备工作 preliminary standard 基础标准 preload 预负荷 pre-locking 预锁定 pre-locking control 预锁定控制 pre-opening 提前开门 pre-opening of door 提前开门 preparatory program 预编程序 preprinted 预先印刷的 prerequisite 前提 pre-select 预选 pre-selection 预选装置 preset 预调，预设定preset time delay 预调延时 preset value 预调值 press working 预压加工 pressing 冲压，加压 press-to-talk system 按钮对讲系统 pressure 压力 pressure gage 压力表，压力计 pressure indicator 压力表 pressure project 样板项目，样板工程 pressure relief valve 压力安全阀 pressure-reducing valve 减压阀 pretension 预应力，预控力 pre-torque 预加力矩 preventative maintenance 预防性维修 preventive maintenance 预防性维修 pre-view 预验，试映 pre-warning 预警，预告 price calculation 价格决算 price increase 提价 price list 价格表 price quotation 报价 price reduction 减价 pricing 计价primary circuit 原电路，一次电路 primary coil 一次线圈 primary fireman's operation 主消防操作 primary machine room 主机房 primary position transmitter (PPT) 第一位置传感器 primary resistor 主电阻，定子电阻 primary wave sensor 地震纵波传感器primary winding 初级绕组 prime cost 原价 prime finish 底漆面层 primer 底漆 priming coated 上底漆 principle 原则，原理 print 印刷 print out 打印出 printed circuit 印刷电路 printed circuit diagram 印刷电路图 printed circuit pattern 印刷电路图形 printer 打印机 priority 优先性 priority floor 优先楼层 priority recall 优先召呼指令 priority travel control 优先运行控制 private accommodation 私人住宅 private code 私用电码，密码private lift 私用电梯 private residence elevator/lift 私宅电梯 probability 概率 probable number of stops 可能停站数 probable stops 可能停站 procedure 程序 process 工艺过。
电梯专业英语
12 Automatic operation for car light and fan
二次按钮取消错误内呼 轿厢灯及风扇自动节能
13 Automatic sliding doors
自动滑门
14 Door re-open by landing call
外呼再开门
15
Repeated door closing in the event of lock failure
轿顶到站钟
25 Operation hour counter
运行小时累计
26 Trip counter
运行次数累计
27
Lockable main switch integrated for controller cabinet
控制柜可锁主开关
No
English
中文
28 Intercom with 5 terminals
No English
中文
1 Car attendance
司机操作
2 Second car operation panel
副轿厢操纵板
3
Special car operation panel for handicapped
4 Out of service indication
残疾人COP 服务中止显示
电梯专业英语
关于电梯功能表和电梯报价表常用语
List of Standard Function for SE – MMR SE - MMR乘客电梯基本功能表
No English
中文RLeabharlann mark1 Door Close Button
关门按扭
2 Door Open Button
电梯专业术语中英文
abbreviation 缩语abnormal "不正常的,反常的"abnormality monitoring 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期，扫描循环acceleration control system 加速度控制系统 acceleration(accel)rate 加速器accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch "通道开关,维修用开关"access way 进出通道accessibility "可通达性,接近的,难易程度" accessible 允许进入accessible space 允许进入的场地accessory "配件,附件"accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic "听觉的,声音的"acrew die 板牙activate "启动,触发"active mode 主动模式actual condition "实际状况,实际条件"actual load 实际载荷actual state 实际状况actual value 实际值actuate "开动,操作,激励"actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator "操纵机构,激励器,螺线管"actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压adaptation "适应,匹配"adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive control system 自适应能力控制系统 addendum "齿顶高,附录"addendum circle 外圆adding working drawing 附加加工图addition "附加物,加法"additional materials 附加材料address 地址adhesion "胶,粘合胶"adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car "相邻轿厢,相邻电梯"adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动 adjustable wrench "活动扳手,可调扳手"adjusting screw 调节螺丝adjustor 调试员administation overjhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced "提前的,先进的"advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值 aerial cableway "空中缆车,架空索道"aerial ropeway "空中缆车,架空索道"aerial tramway "空中缆车,架空索道"aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土 alcove arrangement 电梯U型排列法algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation "分配,分派"allocation of landing call 层站呼梯指令分配allowance "允用误差,加工余量"allowble stress for temporary load 允许暂时应力值 alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage "锚具,锚定"angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承 angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator "报音器,声音合成器"anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会 anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置 anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen power 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour "轴,杆"arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm "臂,支路"armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape recording 磁带录音authority "当局,核准部门"authority of lift acceptance 电梯验收部门authorized "授权的,核准的"authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备 automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门 automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯)back side "后侧,后边"back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank "银行,群组,排"bar "条,棒"bar code 条形码bar lock 杆式锁bare wire 裸线barricade "防护墙,隔墙"barrier "隔板,栅栏"base "基座,基础"base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制 beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias "偏置,偏移"bid "投标,报价"bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binary 二进制binder 装订册bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管 bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade "叶片,刀片,锯片"blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁 blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole "钻孔,镗孔"boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙 bottom counterweight overtravel 轿底对重越程 bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box "盒,箱"box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press "折弯机,压弯机"brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break "切断,破断"break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置 broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken tape sweitch 短带开关bronze 铜brunching "成组,成群"brush finished stainless steel 哑光不锈钢brush holder "刷握,滑环"brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统 building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行buried 埋入的burn in (程序)灌入burr "毛刺,毛边"burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing "衬套,轴套,套筒"butt joint "平接,对焊"button 按钮button switch 按钮开关buyer 买方buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab "轿厢,座舱"cab interior 轿厢内部cabin "轿厢,座舱"cabinet "柜,厢"cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call "呼梯,呼叫"call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯 call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contrl 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel "撤消,取消"cancelingof call signal 呼梯信号消除cancellation "撤消,取消"canopy "顶盖,大蓬"canvas 帆布canvas hose 帆布软管cap "帽,盖子"cap nut 螺母capacitance "电容,电容量"capacitor 电容capacitor motor 电容器电机capacity "载重,容量,定员"capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment "轿厢调度,轿厢分配"car automatic switch landing 轿厢开关自动停站 car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit "轿厢安全门,应急门"car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮 car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior "轿厢外装修,轿厢外表"car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame "轿厢架,轿架"car frame "轿厢架,轿架"car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control "手柄开关操纵,轿内开关控制" car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel "轿厢照明板,照明天花板"car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel with window 轿厢壁板上窗口car platform "轿厢底,轿底"car platform guard 轿厢站台护板car platform sill 轿厢car position indicator "轿厢指示灯,轿厢位置显示" car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof "轿厢顶,轿顶"car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯) car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling "轿厢架,吊架"car station 轿厢操纵站car status information 轿厢运行状态信息car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置 car switch control 轿厢开关控制car switch opration "手柄开关操纵,轿内开关控制"car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit "轿顶安全出口,轿顶应急出口"car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls "轿厢壁,轿壁"car weight 轿厢重量car width 轿厢宽度carbon "碳,石墨"carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card "卡片,纹板"card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency "载波频率,开关工作频率"carrying capacity "载运量,载运能力"cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade "级联,串联"cascade sub-loop 串接式子回路case "箱,盒,外壳"casing "保护套,外套"casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢castor oil 蓖麻油catch "擎子,门扣,捕捉器"catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation "气穴,涡穴,饱和压力点"ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement "水泥,胶合剂"cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门 center plunger hydraulic lift 柱塞直顶式液压电梯center support "中心支撑,中间支撑,第三支撑"center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centrifugal 离心的centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link "链节,链环"chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机 chain tensioning device 链张紧装置chain wheel 链轮chain wheel track 链轮导轨chamger "倒棱,去毛刺"change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character "特征,字符"characteristic "特征,特性"characteristic curve 特性曲线charge "充电,收费"charged "带电,充电"charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke "扼流,截流,阻塞"choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价 cinder concrete 煤渣混凝土circuit 电路circuit breaker "断电器,断路器"circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring "压制环,加紧环"clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度 cleated riser 梯级竖板clerance 间隙clevis U型夹client "客户,买主"clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code "码,符号,规程,规范"code of practice "实施规程,实用规程"code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil "线圈,绕组"coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate "栅栏门,折叠式门"collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection "收集,集合"collective control 集中控制collective full automatic operation 全自动集中控制 collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column "柱,立柱"comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment "隔板,隔室"compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent "有资格的,胜任的"competent personnel "有资格的人员,胜任的人员"competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract "综合维修合同,全包维修合同" comprehensive service contract "综合维修合同,全包维修合同"compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed "隐蔽的,暗式"concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容 condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod "连杆,连接杆"connection 连接connection diagram of controller 控制柜连线图connector "接线柱,连接器"conract specification "合同规定,合同明细表"conract speed "合同速度,额定速度"consecutively departing 依次派出的轿厢console panel "控制柜,控制盘"constant "恒定的,常数"constant HP motor 功率恒定型电机constant speed valve "比例控制阀,调速阀"constant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layout drawing 土建图construction platform "安装平台,施工平台"construction site "安装工地,施工工地"consultant "顾问,咨询机构"consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger "接触指,滑触头"contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract "合同,契约,承包合同"contract capacity "合同载重量,合同容量"contract load 合同负载contract of indemnity 赔偿合同contract party "合同方,合同当事人"contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置 control feature 控制特征control gear 控制论control guard for handrail breakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage "控制电压,操作电压"controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter "整流器,转换头"converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置 cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord "绳索,芯线"cord drive "绳传动,(厅门)"core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner "角,隔"corner post 对角立柱corpus lift 尸体升降机。
电梯行业英语(精简版)
电梯 lift elevator乘客电梯 passenger lift载货电梯 goods lift；freight lift客货电梯 passenger-goods lift病床电梯；医用电梯 bed lift住宅电梯 residential lift杂物电梯 dumbwaiter lift； service lift 观光电梯 panoramic lift观光电梯 glass elevator汽车电梯 motor vehicle lift液压电梯 hydraulic lift专用电梯 special lift高速电梯 high-speed elevator/lift冷库梯 freezer elevator尸体升降机 corpus lift电梯额定速度 rated speed of lift检修运行速度 inspection traveling speed 额定载重量 rated road；rated capacity井道壁 shaft well平层区 leveling zone消防服务fireman service厅门 landing door；hall(大厅) door轿门 car door弹簧缓冲器；蓄能型缓冲器具spring buffer 控制柜 control cabinet；controller操纵箱 operation panel操纵盘 car operation panel呼梯calling landing轿厢超载car overload轿厢底,轿底car platform交流无齿曳引机AC-GL machine有齿轮 geared无齿轮 gearless限速器governor平层传感器 level transducer对重装置,对重counterweight电缆cable呼梯按钮call button配件,附件 accessory选配adapting轿顶照明装置 car top light底坑检修照明装置 light device of pit inspection 蓄电池 accumulator空调 air-condition警报 alarm警铃 alarm bell警铃按钮 alarm button警报蜂鸣器 alarm buzzer超载报警 overload warning对讲机 interphone备用电源stand-by power壁式安装，壁挂式wall surface mounting到站铃 arrival bell蓄电池箱 battery box背景音乐扬声器 BGM speaker蜂鸣器开关 buzzer switch空调制冷 cooler air-conditioner读入 up load卡片,纹板 card卡片读出器 card reader充电 charging set防干扰 anti-nuisance产品说明书 product descritption供电装置 power supply unit通电，上电 power up附加加工图 adding working drawing安装说明书 installation instructions调试 adjusment调试员 adjustor预付款 advance payment售后服务 after sales service销售手段 sales aid销售合同 sales contract销售成本 sales cost销售部，营业部 sales department验收阶段 acceptance period事故 accident电梯验收部门 authority of lift acceptance满载 full load接地 grounding付款条件 condition of payment合同条件 conditions of contract会议室 conference room成本价 cost price免费的 cost-free警告标志 warning sign保修期 period防水的 waterproof接线图，配线图 wiring diagram开关 switch投标，招标 tender三相供电 three phase supply密码 secret code特殊规定 special regulation替换件，代用件replace parts更换，取代replacement要求交货日期 request delivery date救援 rescue报价 price quotation国家规定 national regulation乳白的 milky可编程序控制器 PLC(programable logic controller)隔离双栅极晶体管IGBT（isolated grid binary transistor）智能功率模块 IPM(Intelligent Power Module)点动按钮 inching button。
电梯专业英语[精彩]
![电梯专业英语[精彩]](https://img.taocdn.com/s3/m/b49df133a98271fe910ef9f6.png)
电梯专业英语[精彩]Guide rail (电梯)导轨Traction Machine (电梯) 曳引机 segment display (电梯)段码屏显示 Over Speed Governor (电梯)超速限速器 fish plate(电梯) 接合板, 鱼尾板 HAISUNG 韩国海星产电公司 (韩国最大的专业曳引机厂家之一)，中国分厂TORIN美国通润公司，中国分厂 Intercom (电梯)对讲系统Selcom Door西尔康(公司名)门 DC motor直流电机(马达) Eshine易升(公司名)Anliso安利索(公司名)Door operator(电梯) 门机stainless steel sheet Hairline finish发纹处理不锈钢片Mirror Finish镜面抛光Mirror Etching镜面蚀刻,Elevator Car 电梯罐笼Light curtain光幕保护voice announcement语音报站 Encoder电梯编码器Position Indicator电梯轿厢位置 Emergency break system紧急逃生系统, Suspension road悬挂装置Diversion pulley导向滑轮Rope for elevator电梯钢丝绳 Micro Control微控制(公司名) yaskawa 安川Flat Cable扁形电梯电缆Landing door分层门MS painted, Hairline SS, Mirror SS(烤漆不锈钢，发纹不锈钢，镜面刨光不锈钢)Light curtain光幕保护voice announcement语音报站 Intercom 对讲系统Encoder 电梯编码器Position Indicator 电梯轿厢位置 Emergency break system, Suspension road 紧急逃生系统，悬挂装置电梯专业英语 abbreviation 缩语abnormal 不正常的,反常的abnormality monitoring 异常{BANNED}abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期，扫描循环acceleration control system 加速度控制系统acceleration(accel)rate 加速器accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch 通道开关,维修用开关access way 进出通道accessibility 可通达性,接近的,难易程度accessible 允许进入accessible space 允许进入的场地accessory 配件,附件accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic 听觉的,声音的acrew die 板牙activate 启动,触发active mode 主动模式actual condition 实际状况,实际条件actual load 实际载荷actual state 实际状况actual value 实际值actuate 开动,操作,激励actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator 操纵机构,激励器,螺线管actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压adaptation 适应,匹配adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive control system 自适应能力控制系统addendum 齿顶高,附录addendum circle 外圆adding working drawing 附加加工图addition 附加物,加法additional materials 附加材料address 地址adhesion 胶,粘合胶adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car 相邻轿厢,相邻电梯adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动adjustable wrench 活动扳手,可调扳手adjusting screw 调节螺丝adjustor 调试员administation overjhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced 提前的,先进的advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值aerial cableway 空中缆车,架空索道aerial ropeway 空中缆车,架空索道aerial tramway 空中缆车,架空索道aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土alcove arrangement 电梯U型排列法algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation 分配,分派allocation of landing call 层站呼梯指令分配allowance 允用误差,加工余量allowble stress for temporary load 允许暂时应力值alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage 锚具,锚定angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator 报音器,声音合成器anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen power 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour 轴,杆arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm 臂,支路armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape recording 磁带录音authority 当局,核准部门authority of lift acceptance 电梯验收部门authorized 授权的,核准的authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯) back side 后侧,后边back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank 银行,群组,排bar 条,棒bar code 条形码bar lock 杆式锁bare wire 裸线barricade 防护墙,隔墙barrier 隔板,栅栏base 基座,基础base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias 偏置,偏移bid 投标,报价bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binary 二进制binder 装订册bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade 叶片,刀片,锯片blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole 钻孔,镗孔boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙bottom counterweight overtravel 轿底对重越程bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box 盒,箱box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press 折弯机,压弯机brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break 切断,破断break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken step safety device 梯级破列安全装置broken tape sweitch 短带开关bronze 铜brunching 成组,成群brush finished stainless steel 哑光不锈钢brush holder 刷握,滑环brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行buried 埋入的burn in (程序)灌入burr 毛刺,毛边burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing 衬套,轴套,套筒butt joint 平接,对焊button 按钮button switch 按钮开关buyer 买方buzzer 蜂鸣器buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab 轿厢,座舱cab interior 轿厢内部cabin 轿厢,座舱cabinet 柜,厢cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call 呼梯,呼叫call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contrl 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call load 呼梯输入call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel 撤消,取消cancelingof call signal 呼梯信号消除cancellation 撤消,取消canopy 顶盖,大蓬canvas 帆布canvas hose 帆布软管cap 帽,盖子cap nut 螺母capacitance 电容,电容量capacitor 电容capacitor motor 电容器电机capacity 载重,容量,定员capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment 轿厢调度,轿厢分配car automatic switch landing 轿厢开关自动停站car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom overtravel 轿厢底部越层car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit 轿厢安全门,应急门car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior 轿厢外装修,轿厢外表car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame 轿厢架,轿架car frame 轿厢架,轿架car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car front 轿厢前壁car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control 手柄开关操纵,轿内开关控制car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel 轿厢照明板,照明天花板car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel with window 轿厢壁板上窗口car platform 轿厢底,轿底car platform guard 轿厢站台护板car platform sill 轿厢car position indicator 轿厢指示灯,轿厢位置显示car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof 轿厢顶,轿顶car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯) car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling 轿厢架,吊架car station 轿厢操纵站car status information 轿厢运行状态信息car stop 轿厢停止car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置car switch control 轿厢开关控制car switch opration 手柄开关操纵,轿内开关控制car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit 轿顶安全出口,轿顶应急出口car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls 轿厢壁,轿壁car weight 轿厢重量car width 轿厢宽度carbon 碳,石墨carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card 卡片,纹板card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency 载波频率,开关工作频率carrying capacity 载运量,载运能力cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade 级联,串联cascade sub-loop 串接式子回路case 箱,盒,外壳casing 保护套,外套casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢casting 铸造castor oil 蓖麻油catch 擎子,门扣,捕捉器catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation 气穴,涡穴,饱和压力点ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement 水泥,胶合剂cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门center plunger hydraulic lift 柱塞直顶式液压电梯center support 中心支撑,中间支撑,第三支撑center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centrifugal 离心的centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive 链传动chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link 链节,链环chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机chain tensioning device 链张紧装置chain wheel 链轮chain wheel track 链轮导轨chamger 倒棱,去毛刺change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character 特征,字符characteristic 特征,特性characteristic curve 特性曲线charge 充电,收费charged 带电,充电charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke 扼流,截流,阻塞choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价cinder concrete 煤渣混凝土circle 周期,圆circuit 电路circuit breaker 断电器,断路器circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring 压制环,加紧环clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度cleated riser 梯级竖板clerance 间隙clevis U型夹client 客户,买主clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing travel 门关闭运行closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code 码,符号,规程,规范code of practice 实施规程,实用规程code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil 线圈,绕组coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate 栅栏门,折叠式门collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection 收集,集合collective control 集中控制collective full automatic operation 全自动集中控制collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column 柱,立柱comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment 隔板,隔室compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent 有资格的,胜任的competent personnel 有资格的人员,胜任的人员competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract 综合维修合同,全包维修合同comprehensive service contract 综合维修合同,全包维修合同compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed 隐蔽的,暗式concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod 连杆,连接杆connection 连接connection diagram of controller 控制柜连线图connector 接线柱,连接器conract specification 合同规定,合同明细表conract speed 合同速度,额定速度consecutively departing 依次派出的轿厢console panel 控制柜,控制盘constant 恒定的,常数constant HP motor 功率恒定型电机constant speed valve 比例控制阀,调速阀constant torque motor 力矩恒定型电机construction 安装,施工construction crane 建筑起重机construction layout drawing 土建图construction platform 安装平台,施工平台construction site 安装工地,施工工地consultant 顾问,咨询机构consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger 接触指,滑触头contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract 合同,契约,承包合同contract capacity 合同载重量,合同容量contract load 合同负载contract of indemnity 赔偿合同contract party 合同方,合同当事人contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置control feature 控制特征control gear 控制论control guard for handrail breakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage 控制电压,操作电压controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter 整流器,转换头converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord 绳索,芯线cord drive 绳传动,(厅门)core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner 角,隔corner post 对角立柱corpus lift 尸体升降机correct phase sequence 正确相序correcting 修正,校正correcting travel 校准运行correction 校正,校准corrective maintenance 校正维修corridor 走廊corrosion proof 防腐蚀的corrosion resistant 耐腐蚀的corrosion resistant coating 涂防锈漆层corrosive 腐蚀的cost 成本,费用cost accounting 成倍核算cost analysis 成本分析cost calculation 成倍计算cost comparison 成本比较cost effective 价格划算的cost element 成本项目cost estimate 成本估算。
电梯专业术语中英文
abbreviation 缩语abnormal "不正常的,反常的"abnormality monitoring 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期，扫描循环acceleration control system 加速度控制系统 acceleration(accel)rate 加速器accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch "通道开关,维修用开关"access way 进出通道accessibility "可通达性,接近的,难易程度" accessible 允许进入accessible space 允许进入的场地accessory "配件,附件"accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic "听觉的,声音的"acrew die 板牙activate "启动,触发"active mode 主动模式actual condition "实际状况,实际条件"actual load 实际载荷actual state 实际状况actual value 实际值actuate "开动,操作,激励"actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator "操纵机构,激励器,螺线管"actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压adaptation "适应,匹配"adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive control system 自适应能力控制系统 addendum "齿顶高,附录"addendum circle 外圆adding working drawing 附加加工图addition "附加物,加法"additional materials 附加材料address 地址adhesion "胶,粘合胶"adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car "相邻轿厢,相邻电梯"adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动 adjustable wrench "活动扳手,可调扳手"adjusting screw 调节螺丝adjustor 调试员administation overjhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced "提前的,先进的"advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值 aerial cableway "空中缆车,架空索道"aerial ropeway "空中缆车,架空索道"aerial tramway "空中缆车,架空索道"aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土 alcove arrangement 电梯U型排列法algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation "分配,分派"allocation of landing call 层站呼梯指令分配allowance "允用误差,加工余量"allowble stress for temporary load 允许暂时应力值 alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage "锚具,锚定"angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承 angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator "报音器,声音合成器"anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会 anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置 anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen power 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour "轴,杆"arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm "臂,支路"armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape recording 磁带录音authority "当局,核准部门"authority of lift acceptance 电梯验收部门authorized "授权的,核准的"authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备 automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门 automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯)back side "后侧,后边"back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank "银行,群组,排"bar "条,棒"bar code 条形码bar lock 杆式锁bare wire 裸线barricade "防护墙,隔墙"barrier "隔板,栅栏"base "基座,基础"base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制 beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias "偏置,偏移"bid "投标,报价"bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binary 二进制binder 装订册bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管 bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade "叶片,刀片,锯片"blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁 blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole "钻孔,镗孔"boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙 bottom counterweight overtravel 轿底对重越程 bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box "盒,箱"box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press "折弯机,压弯机"brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break "切断,破断"break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置 broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken tape sweitch 短带开关bronze 铜brunching "成组,成群"brush finished stainless steel 哑光不锈钢brush holder "刷握,滑环"brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统 building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行buried 埋入的burn in (程序)灌入burr "毛刺,毛边"burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing "衬套,轴套,套筒"butt joint "平接,对焊"button 按钮button switch 按钮开关buyer 买方buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab "轿厢,座舱"cab interior 轿厢内部cabin "轿厢,座舱"cabinet "柜,厢"cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call "呼梯,呼叫"call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯 call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contrl 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel "撤消,取消"cancelingof call signal 呼梯信号消除cancellation "撤消,取消"canopy "顶盖,大蓬"canvas 帆布canvas hose 帆布软管cap "帽,盖子"cap nut 螺母capacitance "电容,电容量"capacitor 电容capacitor motor 电容器电机capacity "载重,容量,定员"capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment "轿厢调度,轿厢分配"car automatic switch landing 轿厢开关自动停站 car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit "轿厢安全门,应急门"car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮 car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior "轿厢外装修,轿厢外表"car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame "轿厢架,轿架"car frame "轿厢架,轿架"car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control "手柄开关操纵,轿内开关控制" car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel "轿厢照明板,照明天花板"car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel with window 轿厢壁板上窗口car platform "轿厢底,轿底"car platform guard 轿厢站台护板car platform sill 轿厢car position indicator "轿厢指示灯,轿厢位置显示" car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof "轿厢顶,轿顶"car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯) car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling "轿厢架,吊架"car station 轿厢操纵站car status information 轿厢运行状态信息car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置 car switch control 轿厢开关控制car switch opration "手柄开关操纵,轿内开关控制"car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit "轿顶安全出口,轿顶应急出口"car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls "轿厢壁,轿壁"car weight 轿厢重量car width 轿厢宽度carbon "碳,石墨"carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card "卡片,纹板"card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency "载波频率,开关工作频率"carrying capacity "载运量,载运能力"cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade "级联,串联"cascade sub-loop 串接式子回路case "箱,盒,外壳"casing "保护套,外套"casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢castor oil 蓖麻油catch "擎子,门扣,捕捉器"catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation "气穴,涡穴,饱和压力点"ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement "水泥,胶合剂"cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门 center plunger hydraulic lift 柱塞直顶式液压电梯center support "中心支撑,中间支撑,第三支撑"center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centrifugal 离心的centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link "链节,链环"chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机 chain tensioning device 链张紧装置chain wheel 链轮chain wheel track 链轮导轨chamger "倒棱,去毛刺"change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character "特征,字符"characteristic "特征,特性"characteristic curve 特性曲线charge "充电,收费"charged "带电,充电"charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke "扼流,截流,阻塞"choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价 cinder concrete 煤渣混凝土circuit 电路circuit breaker "断电器,断路器"circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring "压制环,加紧环"clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度 cleated riser 梯级竖板clerance 间隙clevis U型夹client "客户,买主"clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code "码,符号,规程,规范"code of practice "实施规程,实用规程"code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil "线圈,绕组"coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate "栅栏门,折叠式门"collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection "收集,集合"collective control 集中控制collective full automatic operation 全自动集中控制 collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column "柱,立柱"comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment "隔板,隔室"compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent "有资格的,胜任的"competent personnel "有资格的人员,胜任的人员"competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract "综合维修合同,全包维修合同" comprehensive service contract "综合维修合同,全包维修合同"compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed "隐蔽的,暗式"concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容 condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod "连杆,连接杆"connection 连接connection diagram of controller 控制柜连线图connector "接线柱,连接器"conract specification "合同规定,合同明细表"conract speed "合同速度,额定速度"consecutively departing 依次派出的轿厢console panel "控制柜,控制盘"constant "恒定的,常数"constant HP motor 功率恒定型电机constant speed valve "比例控制阀,调速阀"constant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layout drawing 土建图construction platform "安装平台,施工平台"construction site "安装工地,施工工地"consultant "顾问,咨询机构"consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger "接触指,滑触头"contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract "合同,契约,承包合同"contract capacity "合同载重量,合同容量"contract load 合同负载contract of indemnity 赔偿合同contract party "合同方,合同当事人"contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置 control feature 控制特征control gear 控制论control guard for handrail breakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage "控制电压,操作电压"controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter "整流器,转换头"converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置 cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord "绳索,芯线"cord drive "绳传动,(厅门)"core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner "角,隔"corner post 对角立柱corpus lift 尸体升降机。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
电梯行业专用英语
Document serial number【NL89WT-NY98YT-NC8CB-NNUUT-NUT108】
电梯LIFT；ELEVATOR
乘客电梯PASSENGERLIFT
载货电梯GOODSLIFT；FREIGHTLIFT
客货电梯PASSENGER-GOODSLIFT
病床电梯；医用电梯BEDLIFT
住宅电梯RESIDENTIALLIFT
杂物电梯DUMBWAITERLIFT；SERVICELIFT
船用电梯LIFTONSHIPS
观光电梯PANORAMICLIFT；OBSERTIONLIFT
汽车电梯MOTORVEHICLELLIFT；AUTOMBILELIFT
液压电梯HYRAULICLIFT
平层准确度过LEVELINGACCURACY
电梯额定速度RATEDSPEEDOFLIFT
检修速度INSPECTIONSPEED
额定载重量RATEDLOAD；RATEDCAPACITY
电梯提升高度TRAVELINGHEIGHTOFLIFT；LIFTINGHEIGHTOFLIFT
机房高度MACHINEROOMHEIGHT
机房宽度MACHINEROOMHEIGHT
机房宽度MACHINEROOMDEPTH
机房面积MACHINEROOMAREA
辅助机房SECONDARYMACHINEROOM；
隔层SECONDARYFLOOR
滑轮间隔PULLEYROOM
层站台票LANDING
层站入口LANDINGENTRANCE
基站MAINLANDING；MAINFLOOR；HOMELANDING
预定基站PREDETERMINEDLANDING
底层端站BOTTOMTERMINALLANDING
顶层端站TOPTERMINALLANDING
层间距离FLOORTOFLOORDISTANCE；INTERFLOORDISTANCE 井道WELL；SHAFT；HOISTWAY
单梯井道SINGLEWELL
多梯井道MULTIPLEWELL；COMMONWELL
井道壁WELLENCLOSURE；SHAFTWELL
井道宽度WELLWIDTH；SHAFTWIDTH
井道深度WELLDEPTH；SHAFTDEPTH
底坑PIT
底坑深度PITDEPTH
顶层高度HEADROOMHEIGHT；HEIGHTABOVETHEHIGHESTLEVELSERVED；TOPHEIGHT 井道内牛腿；加腋梁HAUNCHEDBEAM
围井TRUNK
围井出口HATCH
开锁区域UNLOCKINGZONE
平层LEVELING
平层区LEVELINGZONE
开门宽度DOOROPENINGWIDTH
轿厢入口CARENTRANCE
轿厢入口净尺寸CLEARENTRANCETOTHECAR
轿厢宽度CARWIDTH
轿厢深度CARDEPTH
轿厢高度CARHEIGHT
电梯司机LIFTATTENDANT
乘客人数NUMBEROFPASSENGER
油压缓冲器工作行程WORKINGSTROKEOFOILBUFFER
弹簧缓冲器工作行程WORKINGSTROKEOFSRINGBUFFER 轿底间隙BOTTOMCLEANCESFORCAR
轿顶间隙TOPCLEARANCESFORCOUNTERWEIGHT
对重装置顶部间隙TOPCLEARANCESFORCOUNTERXEIGHT 对接操作规程DOCKINGOPERATION
隔层停*操作SKIP-STOPOPERATION
检修操作规程INSPECTIONOPERATION
电梯拽引型式TRACTIONTYPESOFLIFT
电梯拽引机绳拽引HOISTROPESRATIOOFLIFT
消防服务FIREMANSERVICE
独立操作INDEPENDENTOPERATION
缓冲器BUFFER
油压缓冲器(耗能型缓冲器)HYDRAULICBUFFER；OILBUFFER 弹簧缓冲器；蓄能型缓冲器具SPRINGBUFFER
减振器具VIBRATINGABSORBER
轿厢CARLIFTCAR
轿厢底；轿底CARPLATRORM；PLATFORM
轿厢壁；轿壁CARENCLOSURES；CARWALLS
轿车厢顶；轿顶CARROOR
轿厢装饰顶CARHANDRAIL
轿厢扶手CARHANDRAIL
轿顶防护栏杆CARPROTECTIONBALUSTADE
轿厢架；轿架CARFRAME
检修门DOOROPERATOR
检修门ACCESSDOOR
手动门MANUALLYOPERATEDDOOR
自动门POWEROPERATEDDOOR
层门；厅门LANDINGDOOR；SHAFTDOOR；HALLDOOR 防火层门；防火门RIER-PROOFDOOR
轿厢门；轿门CARDOOR
安全触板SAFETYEDGESFORDOOR
铰链门；外敞门HINGEDDOOR
栅栏门COLLAPSIBLEDOOR
水平滑动门HORIZONTALLYSLIDINGDOOR
中分门CENTEROPENINGDOOR
旁开门TWO-SPEEDSLIDINGDOOR
双折门TWO-PANELSLIDINGDOOR
双速门TWOSPEEDDOOR
左开门LEFTHANDTWOSPEEDSLIDINGDOOR
右开门RIGHTHANDTWOSPEEDSLIDINGDOOR
垂直滑动门VERTICALLYSLIDINGDOOR
垂直中分门BI-PARTINGDOOR
拽引绳补偿装置COMPENSATINGDEVICEFORHOISTROPES
补偿绳装置COMPENSATINGROPEDEVICE
补偿绳防跳装置ANTI-REBOUNDOFCOMPENSATIONROPEDEVICE 地坎SILL
轿厢地坎CARSILLS；PLATETHRESHOLDELEVATOR
层门地坎LANDINGSILLS；SILLELEVATORENTEANCE
轿顶检修装置INSPECTIONDEVICEONTOPOFTHECAR
轿顶照明装置CARTOPLIGHT
底坑检修照明装置LIGHTDEVICEOFPITINSPECTION
轿厢内指层灯；轿厢位置指示CARPOSITIONINDICATOR
层门门套LANDINGDOORJAMB
层门指示灯LANDINGINDICATOR；HALLPOSITIONINDICATOR 层门方向指示灯LANDINGDIRECTIONINDICATOR
控制屏CONTROLPANEL
控制柜CONTROLCABINET；CONTROLLER
操纵箱OPERATIONPANEL
操纵盘CAROPERATIONPANEL 警铃按钮ALARMBUTTON。