钻井词汇(必修)
石油钻井英语词汇
对照实物确认的钻井词汇一、井口与井控1.套管头升高短节（上下由法兰连接，中间是三通或四通）casing spool2.油管悬挂器tubing hanger3.油管悬挂器上边接有阀门的盖子tubing bonnet4.（可焊接的）导管头（接箍）conductor connector5.（可焊接的）套管头（接箍）casing connector6.井口帽blanking cap & plug7.三闸板防喷器triple slide-lok preventer8.双闸板防喷器double slide-lok prevente9.油/套管升高短节tubing/casing riser10.整体式升高短节integral union riser11.法兰×丝扣井口转换头wellhead adapter12.井口四通两边的横向阀门wing valves13.油管悬挂器上边的变径法兰大小头bonnet14.上边是法兰的套管头casing flange15.只上边是法兰，下边与表层套管焊接的套管头casing head16.套管头内的卡瓦casing slips17.（上法兰小，下法兰大）变径套管头casing spool crossover18.与导管焊接的坐在圆井底的套管头landing head flange top19.卡瓦密封套管悬挂器slips seal casing hanger20.（上下是法兰，中间是四通的）油管升高短节tubing spool21.柔性封隔闸板flexpacker ram22.可变径闸板variable bore ram23.剪切闸板shearing blind ram24.卡瓦型套管悬挂器slip-type casing hangers25.高负荷悬挂器high-load hanger26.悬挂器断开式密封圈hanger isolation seal ring27.井口封隔变径变压法兰（中间有几道密封圈，下边是低压，上边是高压）packoff/crossover flange28.油管头（下法兰大，内带密封圈；中间是四通，上法兰小）tubing heads29.底（下）变径法兰（下边内径大，上边内径小）basic adapter30.单密封变径法兰（下内径大，上内径小）single seal bore adapter31.变径大小头（下边是法兰，上边是本体上钻孔攻丝扣）coupling adapter32.油管悬挂器转换大小头短节（上法兰小，下法兰大，下法兰内有丝扣）tubingsuspension adapter33.双油管悬挂器dual completion tubing hanger34.双密封孔连接法兰dual seal bore adapter35.锁紧螺丝lockdown screw36.（地面）单油管密封总成single packer completion37.法兰式采油树盖子flanged tree caps38.扰性油管悬挂器coiled tubing hanger39.扰性油管头coiled tubing head40.高级环形防喷器芯子supreme stripper41.旋转防喷器rotating BOP42.下面带有母扣的套管头casing head housing with female casing thread43.带底盘的套管头casing head housing with base plate44.（上法兰小，下法兰大）带四通的套管头crossover casing spool45.常规油管头conventional tubing head46.防喷器吊装系统BOP handling system47.（装在压井管汇一边的）单流阀check valve48．标准扰性油管树总成typical coiled tubing tree assembly49.套管悬挂器（即套管头内的卡瓦）casing hanger50.万能防喷器芯子packing unit51.装压力表的井口或采油树顶盖flow adapter52.（较大较厚的）密封圈packoff53.（从井口通往节流管汇的）液控阀HCR valve54.回压阀（止回阀）check valve55.套管头外壳CHH＝casing head housing56.套管头上的四通CHS=casing head spool57.用在套管头与四通之间的变径变压法兰DSA=drilling spool adaptor58.地平面GL=ground level59.手动阀门MV=manual valve60.双头螺栓连接的油管头四通DSTHS=double studded tubing head spool61.双头螺栓连接的密封转换法兰DSPOAF=doublestuddedpack-offadaptorflange62.大直径导管stovepipe63.压井钻井液KWM=kill weight mud64.井口最大允许环空压力（套压）MAASP=maximumallowableannularsurfacepressure65.起钻POOH=pull out of hole66.下钻RIH=run in hole67.关井立管压力SIDPP=shut-in drill pipe pressure68.关井套压SICP=shit-in casing pressure69.副司钻AD=assistant driller70.垂直井深TVD=true vertical depth71.垂直方向TVD=true vertical direction72.压井排量和压力KRP=kill rate & pressure73.初始循环压力ICP=initial circulating pressure74.终止循环压力FCP=final circulating pressure75.测量深度（实际井深）MD=measured depth76.钻井液密度MD=mud density77.每分钟冲数SPM=strokes per minute78.井底压力不变CBHP=constant bottom-hole pressure二、套管和固井1.（固井或压井用的高压管线）可转向短节swivel joint2.由壬hammer lug unions3.防硫化氢由壬（H2S）sour gas unions4.焊接由壬butt weld unions5.上扣由壬threaded unions6.焊接弯头welded elbow7.（约两三米长，两三吋的）两头带由壬的高压固井、压井管线pup joint8.水泥头plug lounching head9.（刮管器上的）刮刀片scraper blades10.回收式水泥分割器retrievable cement packoff11.可钻水泥分割器drillable cement packoff12.杯形水泥分割器cup style cement packoff13.封割器坐入工具packoff setting tool14.带可钻封隔器的尾管挂liner setting collar with drillable packoff15.带回压阀的引鞋PVTS16.自动灌钻井液引鞋self-filling float shoe=fill-up valve=fillup mode17.带分流孔的（防堵）引鞋down-jet float shoe18.桥塞bridge plug19.机械式桥塞（或尾管）送入工具mechanical setting tool20.大直径限位环oversize stop ring21.封隔器胶皮限位套packer thimble22.（螺旋刮管器上的）刀片限位套blade retainer23.单回压阀引鞋single float set shoe24.双回压阀引鞋dual float set shoe25.扣闩式尾管固井胶塞承托环latch landing collar26.旋转式尾管送入器rotating liner running tool27.坐入器清杂网setting tool debris screen28.套管扶正器限位套stop collar=dog collar29.不焊接的套管扶正器non-welded centralizer30.半钢性套管扶正器semi-rigid centralizer31.无焊接涡流式套管扶正器non-welded turbolizer32.钢性套管扶正器rigid centralizer33.水泥篮cement basket34.固体分流器solid body diverter35. (双级固井)第一级堵塞器first stage sealing plug36. (双级固井)第二级“炮弹”式旁通打开器free-ball opening device37. (双级固井)第二级堵塞器closing plug38. (双级固井)泵冲式旁通打开器pump down opening plug39. (双级固井)旁通堵塞器by-pass plug40.分级箍stage cementing collar41.套管快速护丝quick-clamp thread protector42.套管双公短节casing nipple43.引鞋float nose=guide shoe=set shoe44.铰链式套管扶正器hinge-type centralizers45.多级固井分级箍multiple stage cementing collar46.单级固井水泥头single stage cementing head47.双级固井水泥头two stage cementing head48.有焊接弓形弹簧扶正器welded spring bow centralizer49.无焊接直条扶正器non-weld straight bow centralizer50.短螺旋刚性扶正器short spiral rigid centralizer51.扶正器限位套stop collar52.套管涨管器casing roller53.插入杆stinger54.插入（接）头tag-in adapter55. (插入式固井的)插入座tag-in float collar56.插入式固井下部结构tag-in assembly57.插入式固井用的钻杆座和卡瓦drill pipe bowl and slips58. (插入式固井)水泥头pack-off head assembly59. (插入式固井)上丝扣式的插入头screw-in adapter60. (插入式固井)锁闩式插入头screw-in adapter61. (插入式固井)插入密封头stab-in seal sub62.螺旋清砂扶正器（套）spiral solid stand-off centralizers63.直刮刀式清砂扶正器solid “straight blade” stand-off centralizer64. (扶正器与井壁)接触长度wall contact65.回压阀back pressure valve66. (固井或压井用)约2～5米长，2吋或3吋高压管线longsweep hose67.双公由壬短节male×male union ends68.公母由壬短节male×female union ends69.总长overall length70.水泥头releasing bail operator71.进扣长度make up loss=thread swallow三、管材与配件1.四通full flow cross2. (等边)三通long sweep full flow tee3. 90度弯头long sweep 90°ell4.侧三通long sweep tee5.顶部有出口的160度立管鹅颈管三通standpipe gooseneck 160°with top outlet6. 45度弯头long sweep 45°ell7.大小头adapter sub8.循环三通T-pump-in sub9.变径大小头（粗细扣大小头）crossover adapter10.短钻杆drill pipe pup joint11.十字四通连接管cross connector12.丁字三通连接管tee connector13.活动转向短节（固井、压井管线）Chiksan swivel joint14.伸缩短节expansion joint15.细扣管线堵头bull plug16.细扣管线大小头line pipe swages17.（两半式带手柄的）水管线卡子hinglelok18.（两半式用两个螺栓固定的）水管线卡子rigidlite coupling19.细扣管线接箍（双母）line pipe coupling=steel merchant coupling20.丝扣连接旁通（出口）threaded side outlet21.螺栓连通旁通studded side outlet22.母扣female threaded23.盲板法兰blind flange24.内径带丝扣的法兰companion flange25.内径带密封圈的法兰packoff flange26.变径法兰crossover flange27.与法兰连接的方块四通studded cross28.与法兰连接的方块三通studded tee29．与法兰连接的丝扣三通flanged by thread tee30.单头可转短节（仅一头能转动的短节）single swivel coupling31.单弯脖单头可转短节single swivel with one elbow32.双弯脖单头可转短节single swivel with two elbows33.双弯脖双头可转短节two swivels with two elbows34.单弯脖双头可转短节two swivels with one elbow35.三弯脖双转向短节two swivels with three elbows36.三弯脖三转向短节three swivels with three elbows37.双弯脖三转向短节three swivels with two elbows38.方（块）铁直角弯脖block connector39. 90度弯脖long radius connector40.可变径弯接头knuckle joint41.管线滤清器strainer四、地面与井下工具A.地面工具1.砂轮片grinding wheels2.手动钻具台肩修整器shoulder facing device3.内六楞凹头螺栓allen head cap screws4.六楞弯头扳手allen wrench5.带限位台肩的接头stop sub6.固定螺丝（限位螺丝）retainer screw7.方瓦驱动方钻杆square drive8.销子驱动方钻杆（滚子方补心带四个爪）pin drive9.高强度滚子方补心heavy duty roller Kelly bushing10.钻杆卡瓦rotary slips11.钻铤卡瓦drill collar slips12.导管卡瓦conductor pipe slips13.套管卡瓦casing slips14.铰链式套管卡瓦hinged casing spider15.气动套管吊卡/卡瓦casing elevator/spider16.安全卡瓦clamp17.滚筒排绳槽lebus groove18.装在井架大腿上的死绳固定器mast leg mount anchor19.死绳固定器wireline anchor＝deadline anchor20.绷绳地锚deadman21.离合器clutches22.刹车片brakes23.端面离合器刹车片disc brakes24.快速放气阀quick release valves25.转子密封器rotorseals26.（大直径管线）充气密封圈air-o-union27.（保险）放压阀pressure relief valve28.钻井液防喷盒mud miser29.鼠洞上扣钳和吊卡mousehole spinning wrench & elevator30.销子驱动方补心pin drive Kelly bushing31.方铁驱动方补心square drive Kelly bushing32.高压胶管diver hose33.滚筒刹带brake bands34.刮泥器pipe wipers35.高强度链钳heavy-duty chain36.泵缸套imperial liner37.中间带钢圈的活塞imperial piston38.耐用活塞（中间无钢圈）extra-life bonded piston39.中间有扶正器（孔）的阀体和阀座imperial valves and seats40.带四个爪的阀体和阀座roughneck full open series valves and seats41.刹带片brake blocks42.泵空气包胶囊diaphragms for pulsation dampener43.方钻杆下旋塞Kelly guard44.小鼠洞上扣器rotating mousehole45.（钻台上用的）气葫芦air tugger46.分体式游车大钩trunion supported hook47.连体式游车大钩adapter supported hook48.喷射式混合漏斗jet mixing system49.单作用泵活塞single acting pump piston50.双作用活塞泵double acting pump piston51.手动油管卡瓦manual tubing spider52.气动油管卡瓦air powered tubing spider53.气动卡瓦slip spider54.气动吊卡slip elevator55.长体手动卡瓦extra long slips56.多片式钻铤卡瓦multisegment drill collar slips57.链钳chain tong58.（大管线）充气密封圈air-inflatable tight seal59.快扣加固井架用保险带snap-on cable reinforced derrick belt60.高台罐区用保险带platform and tank belt61.放线工保险带lineman’s belt62.快扣弯连接二层台和井架保险带（宽腰有背带）snap-onandbuckle-oncombination monkey board and derrick belt63.（宽腰无背带）加固二层台保险带reinforced monkey board belt64.弯接加固二层台保险带buckle-on cable reinforced derrick belt65.高强度蛇皮接绳器heavy-duty grips66.单股或双股编织接绳器single or double weave grip67.三股编织接绳器triple weave grips68.四股编织接绳器quad weave grips69.单（双）接环蛇皮接绳器single (dual) eye grip70.顶部开口单接环蛇皮接绳器single eye top opening grip71.顶部开多口单环蛇皮接绳器topside multiple opening grip72.接绳转向器directional boring swivels73.指重表weight indicator74．压力表pressure gauge75.电子转盘扭距表electric rotary torque76.大钳扭距tong torque77.泵冲数表SPM pump speed indicator78.自动送钻automatic driller79.二层台钻杆支梁finger board80.刹车鼓brake rims81.钻杆刮泥器(drillpipe) stripper rubber82.接链器chain connector83.（大绳）排绳器wireline guide84．单头内六方扳手impact box end wrench85.六楞方钻杆hexagonal Kelly86.（装在滚筒护罩上的）防碰天车阀short toggle valve87.拧扣器make-up/break-out unitsB.井下工具1.铆钉式可调螺旋扶正器undergauge adjustable stabilizer2.钻头导向器bit pilot3.整体式螺旋扶正器integral blade stabilizer4.焊接式螺旋扶正器welded blade stabilizer5.可变径扶正器variable gauge stabilizer6.可更换的扶正器套stabilizer sleeves7.换套扶正器心轴stabilizer mandrel8.滚子扶正器roller reamer9.单级牙轮扩大器（下边可接领眼钻头）single stage hole opener10.六方减震器hex bumper sub11.牙轮取心钻头roller core-barrel head12.刮刀取心钻头blade core-barrel head13.钻铤螺旋槽spiral groove14.方钻铤square drill collar15.光钻铤slick drill collar16.（钮扣式）碳化钨扶正器套sleeve with tungsten carbide buttons17.镍合金扶正器套sleeve with nivalloy18.滚子扶正器rotaryreamers19.（密封轴承）井眼扩大器sealed bearing hole openers20.钻头喷嘴jet nozzle21.无卡簧槽的喷嘴standard nozzle22.有卡簧槽的喷嘴shrouded nozzle23.磨鞋式螺旋扶正器watermelon mill24.磨鞋式短螺旋扶正器string mill25.螺旋加重钻杆spiral-wate drillpipe26.扩大器U/R=underreamer五、钻井液药品与缩写符号1.稀释剂（液体，约25kg1桶）2.抗高温流变性稳定剂3.抗高温流变性稳定剂，属稀释剂，加重时用一点，不增稠，液体约200kg1桶4.液体，润滑剂，约200kg1桶5.高温高压失水稳定剂（降失水），干粉，约25kg1袋6.（有时只写作XCD或CD），生物聚合物，降失水，调流变性，提粘（钻井液稀—流变性低）7.干粉堵漏剂（类似国内的随钻堵漏剂），成分：锯末、稻糠、植物种子8.中号碎核桃壳（相当于麦粒大小）9.细云母粉云母片10.蚌壳渣11．（有时只写作PAC），干粉，相当于国内的CMC，有时在Drispac后加上R或SL，其意是：R—regular高粘，SL－superlow低粘，中文名：聚阴离子纤维素12．滤液酚酞碱度13．钻井液酚酞酸度14.滤液甲基橙碱度15.亚甲基蓝测定法（膨润土含量）16.钻井液密度17.每加仑磅18.粘度19.塑性粘度20.秒21.夸脱22.厘米/秒23.屈服点（流动点）24.磅25.英尺26.静切力（胶凝强度）27.（氢离子浓度倒数的对数）28.立方厘米立方容积29.美国石油学会精确位置显示器30.桶31.钙32.百万分率（百万分之几）33.钻屑34.磅/桶35.尽可能低36.失水37.高温高压38.聚阴离子纤维素衍生物六、打捞工具1.平底牙轮磨鞋2.带锯齿的铣鞋3.铣锥4.枣核形铣锥（两头带丝扣）5.打捞颈6.篮式卡瓦7.螺旋弹簧式卡瓦8.螺旋弹簧式卡瓦控制环9.篮式带铣鞋卡瓦控制环10.母铣锥11.大头壁挂式坡口打捞引鞋12.厚壁管制的壁钩13.卡瓦打捞筒加长管14.母锥15.带坡口引子的母锥16.打捞矛上的退出环17.笔尖式引子18.（打捞筒内的）落物打捞爪19.锯齿底引子20.壁钩式坡口引子21.四楞短锥体带喷嘴磨鞋22.锥头引子23.爪式引鞋24.锯齿式引鞋25.随钻打捞杯26.刮刀式磨鞋27.28.。
(完整版)石油钻井工程英语词汇
石油钻井工程英语词汇2008-10-15第一章：石油钻井工程英语基础词汇第1 节石油钻井工程基础词汇钻井：drill定向斜井：directional drilling欠平衡钻井：under-balance drilling海上钻井：off-shore drilling陆地钻井：on-shore drilling钻头：drill bit刮刀钻头：drag bit牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit) 金刚石钻头：diamond bit取心钻头：coring bit钻头浮阀：float valve钻头水眼：bit nozzle(or jet)钻头水眼刺:bit nozzle washed out钻头规：bit caliper(bit gauge)钻头泥包：bit is balling钻头钝了，我建议现在起钻：bit is dull. I suggest to POOH now地址：北京市朝阳区东三环中路7号财富中心A座601 邮编：100020钻铤：DC(drill collar )光钻铤slick drill collar，螺旋钻铤spiral drill collar钻杆：DP(drill pipe )方钻杆：kelly公扣：pin end母扣：box end内平式连接：IF(internal flash)正规式连接：REG(regular)贯眼式连接：FH(full hole)加重钻杆heavy weight drill pipe短钻杆pop joint井下马达：downhole motor涡轮钻具：turbine震击器：drilling jar减震器：absorber下部钻具组合：BHA（bottom hole assembly）钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer）钻机：drill rig钻井泥浆：drilling mud钻井液：drilling fluid钻井设备：drilling equipment油：oil原油：crude oil天然气：nature gas煤层气：coal-bed gas石油：petroleum中国石油（简称）：CNPC（China National Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall Drilling Company)采油：oil production产油层(目的层)：reservoir( or pay zone)钻进：drilling调整钻井参数以得到理想的机械钻速：play the drilling parameters to get fast ROP起钻：POOH(pull out of hole)下钻：RIH(run in hole)下套管：run casing(or RIH with casing)短起下钻：wiper trip循环泥浆：circulate泥浆：reverse circulate中途循环泥浆：break circulation分段下钻：RIH in stages通井：control trip划眼：reaming倒划眼：back reaming接单根：make connection滑、割大绳：slip and cut drilling line by ton-mile保养设备：maintain the equipment修理设备: repair (or fix) the equipment保养顶驱：service TDS保养冲管：lubricate wash pipe待工日费：standby rate今天零日费：there is no day rate today(zero day rate today)我可以为您做，但必须收费，请理解I can do for you and I have to charge(back charge) you. Please give me full understanding.不在我的职责范围之内，我要汇报领导，一有消息会马上告诉你It is out of my power and I have to report to my boss. I will let you knowas soon as I get news.大鼠洞：rat hole小鼠洞：mouse hole钻具错扣：the connections are crossed钻具粘扣：thread is galled丝扣坏了：the thread is damaged起钻错扣：alternate the connections新钻具或接头磨扣：break in the new tool joint新钻头磨合：break in the new bitPDC 钻头井底造型：shape the PDC bit跳钻：rough drilling( vibrated drilling, bit is bouncing)蹩钻：rough drilling（drilling torque is abnormally high）缩径：tight hole起钻遇卡：get overpull下钻遇阻：set weight部分漏失：partially lost circulation全部漏失：totally lost circulation盲钻：blind drilling堵水眼：bit jets are blocked掉水眼：bit jets are lost憋压：the pressure is built up卸压：release pressure试压：pressure test功能测试：function test双方独自检查：double check地质：geology地质专业人员：geologist物理：physics地球物理勘探：geo-physical exploration.测井：logging电测井作业：wireline logging operation泥浆测井：mud logging井（副词“好”含意）：well拓展记忆：井眼：bore hole油气井：oil&gas well试井：well test井下：down-hole井下作业：down-hole operation第2 节石油钻井方法基础词汇钻井原理：the principles of drilling顿钻钻井：percussion drilling，cable-tool drilling 旋转钻井：rotary drilling大位移井：big distance( or extended ) well侧钻井：sidetracking drilling水平井：horizontal well探井：wildcat，wildcat drilling深井：deep well浅井：shallow well老井：maturing well丛式钻井：cluster well drilling煤层气井：coal-bed gas well生产井：production well报废井：abandoned well停产井：none-production well井下情况：downhole condition第3 节石油钻井技术基础词汇技术规范，技术指标，技术性能：specification拉伸：tension拉伸强度：tensile strength弯曲强度：bending srength最小屈服强度：minimum torsional strength应力：stress压力：pressure应力点：stress point压力降：pressure drop压力梯度：pressure gradient回压：back pressure大气压：atmosphere压差：pressure difference静液柱压力：static fluid cloumn pressure地层压力：formation pressure坍塌压力：collapse pressure破裂压力：fractured pressure液体：liquid固体：solid气体：gas，air正的：positive负的：negative水平的：horizontal垂直的：vertical第4 节石油钻井参数基础词汇钻压：WOB（weight on bit）转盘转速：RPM（rotation per minute）泵压：SPP(slurry pump pressure)泵冲：SPM（stroke per minute）排量：FR(flow rate)大钩负荷：hook load扭矩：torque反扭矩：reactive torque钻速：ROP(rate of penetration)顶驱：TDS(top drive system)钻井周期：drilling period钻井成本：drilling costs井眼尺寸：hole size垂深：TVD(total vertical depth)井深：MDD(measured depth)水平位移：horizontal displacement井斜角：angle( or hole inclination)方位角：azimuth井眼环空：annulus第5 节石油钻井作业现场工作人员名称甲方：oil company(operator)钻井承包商：drilling contractor第三方（分包商）the third party(sub-contractor)钻井经理：drilling manager监督：supervisor钻井监督：DSV(drilling supervisor) or Companyman 地质监督：geologist泥浆工程师：mud engineer固井工程师：cementing engineer泥浆录井工：mud logger钻井队：drilling crew，drilling team钻井1 班：drilling shift one总经理：general manager总工程师：chief engineer项目经理：project manager(country manager)作业经理：operation manager财务经理：financial manger会计：accountant平台经理：rig manager带班队长：tool pusherHSE 监督：HSE officer司钻：driller副司钻：assistant driller井架工：derrick man钻工：roughneck（or floorman）场地工：roustabout泥浆工：mudman发动机工：motorman机械师：mechanic电工：electrician电焊工：welder司机：driver吊车司机：crane operator铲车司机：forklift operator营房经理：camp boss医生：doctor材料员：material man(storekeeper)炊事员：cook翻译：interpreter洗衣工：laundry man厨房服务生：waiter保安：watchman(or security)机械工程师：mechanic engineer第6 节石油作业现场常用工具扳手：wrench螺丝起子：screwdriver多角螺丝起子：Phlilips screwdriver （cross-headed screwdriver）撬杠：bar加长撬杠：cheater bar活动板手：monkey wrench，adjustable wrench钳子：pliers钩子：hook台钳：bench vice钢挫：file榔头：hammer锤击扳手：hammer wrench搬手：spanner内六角扳手：Allen key钢锯：hacksaw砂纸：sandpaper管钳：pipe tongs(pipe wrench)链钳：chain tong千斤顶：jack黄油枪：grease gun吊车：crane牵引绳：tag line电焊条：welding rod拖拉机：tractor推土机：bulldozer硬尺：ruler游标卡尺：Vernier slide油漆：paint铅油：dope油漆刷：paint brush铅油刷：dope brush绝缘胶布：electrical tape电线：wire插头：plug电插座：outlet(receptacle or switchboard)开关：switch螺栓：bolt螺帽：nut垫片：washer钉子：nail手电钻：hand drill钻头：bit工作台：workbench工具箱：toolbox胶水：glue胶棒：glue bar护丝：thread protector手轮：hand wheel脚轰油门：throttle联接法兰：coupling flange(or adaptor flange) 安全带：safety belt安全帽：helmet工作靴：safety boot工衣：coverall棉袄：coat防护眼镜：safety goggle手套：gloves口罩：mouth mask围裙：apron洗眼台：eye washing station灭火机：fire extinguisher消防栓：fire -hydrant水龙头：water tap消防斧：fire fighting axe铲子：shovel手砂轮：emery wheel左转：turn left右转：turn right手势：gesture信号：signal垃圾：waste garbage拖把：mop接头：sub配合接头：X-over ，cross-over提升短节：lifting sub卡瓦：slips放卡瓦：set slips母锥：box tap公锥：taper tap打捞矛：fishing spear安全接头：safety sub柔性短节：flexible joint井口盖子：wellhead cover防喷盒：mud boxBOP 吊装：BOP trolley( BOP hoist) 吊卡：elevator吊环：elevator links安全卡瓦：safety clamp(dog collar) 钻杆架：pipe rack水龙头提环：swivel bail材料房：warehouse绳卡：bullnose clamp(guy anchor) 绳套：sling吊带：soft sling(belt)卸扣：shackle吊装工具：lifting gear维护保养：maintenance内钳：make-up tong外钳：break-out tong液压大钳：power tong液压猫头：E-zy tong兜绳：mule line四通阀：four-way valve三通：Tee软管：hose球阀：ball valve闸板阀：gate valve单流阀：back valve灌注泵：supercharge pump第二章：石油工程常用设备及专业术语第1 节钻井设备部分井架：Derrick(or mast)起（放）井架：erect(lay down) Derrick 底座大梁：sill钢木基础：mat铅锤：plumb水平仪：level架，台：rack立根盒：setback area坡道：V door(or ramp)猫道：catwalk二层台：monkey-board圆井盖：cellar cover天车：crown block防碰天车：crown-o-matic天车梁：crown block beam天车台：water table游动滑车：traveling block钻井大绳：drilling line引绳：guide line穿大绳：string-in drilling line金属线，电线：wire，cable钢丝绳股：strand截断：cutoff滑车，滑轮，皮带轮：pulley(hoist)手拉葫芦：hand pulley吊耳：lifting eye顶驱：top drive大钩：hook大钩弹簧：hook spring大钩销子：hook pin大钩锁紧装置：hook locking device大钩悬挂高度：hook height水龙头：swivel鹅颈管：gooseneck冲管：wash pipe水龙头盘根：swivel packing钻井水龙带: rotary hose( kelly hose)立管：stand pipe立管管汇：stand pipe manifold高压管线：high pressure line由壬：union低压管线：low pressure line传感器：sensor放压管线：relief line转盘：Rotary Table转盘方瓦：master bushing方补心取出装置：bushing handling tool方补心：kelly drive bushing方孔：square opening小鼠洞：mouse hole大鼠洞：rat hole绞车：Drawworks挂合（摘开）绞车：engage(disengage) drawworks液压绞车：hydraulic winch气动绞车：air tugger(air hoist)滚筒：drum( reel)滚筒高速气离合器：high speed clutch滚筒低速气离合器：low speed clutch锚头：cathead液压猫头：E-zy tong上扣猫头：make up cathead卸扣猫头：make out cathead牙嵌离合器：jaw clutch涡磁刹车：eddy current brake(electromagnetic brake) 猫头轴：cathead shaft猫头绳：cathead line死绳：dead line死绳固定器：dead line anchor间隙：gap死绳固定器膜片：dead line diaphragm上扣：make up上扭矩：torque sth卸扣，卸开：break out上紧，固定：tighten（fasten）松开，松扣：loosen加载：load卸载：unload盘式刹车：disc brake刹车总成：brake assembly刹车轴：brake shaft刹车带：brake band刹车片：brake block液压油箱：hydraulic power unit液动试压泵：hydraulic test pump 液压大钳：hydraulic （power）tong 倒档齿轮：reverse gear动力扳手：power wrench吊钳钳头：hinged jaw钳牙：die大钳锁销：latch大钳悬臂：suspension bar平衡重：counterbalance weight吊钳钳臂：tong arm第2 节钻井泵类及相关设备泥浆泵：mud pump活塞：piston活塞杆：piston rod活塞皮碗：piston cup缸套：liner凡尔体：valve body凡尔座：valve seat凡尔箱：pump module阀弹簧：valve spring阀杆：valve lever阀面：valve face阀帽：valve bonnet空气包：pulsation damper充氮气：refill with nitrogen泥浆泵安全阀：pop-off valve卸压管线：release line排出阀：discharge valve吸入阀：suction valve上水滤子：screen油尺：oil-level dipstick灌注泵：supercharge pump冷却水泵：cooling pump潜水泵：submersible pump盘根盒：stuffing box叶轮：impeller单向阀：check valve（single-pass valve）安全阀：safety valve手动阀：manual valve液动阀：hydraulic valve拉杆：tie rod，tension bar压力表：pressure gauge冲数：strokes排量：flow rate80 冲(次)/分：eighty strokes per minute泥浆罐：mud tank倒泥浆：transfer mud循环罐：active tank储备罐：reserve tank起下钻罐：trip tank溢流检查：flow check沉砂罐：satteling tank锥形罐：sand trap震动筛：sahle shaker筛布：screen目数：mash除砂器: desander除泥器: desilter离心机：centrifuge泥浆分配槽：spider box缓冲罐buffer tank第3 节与泵操作有关的实用短语没有压力：No pressure压力过高：The pressure is too high返回太少：Mud return is too few水太少：Water is not adequate.抢修：Rush to repair请看记录：Please check the record没作记录：No record available加化学药品：add chemicals测定比重：measure mud weight(specific gravity) 测定失水：measure water loss泥饼：mud cake测定切力：measure gel strength停泵：stop pump请打手势：Please make a gesture转动一周：turn round a circle垫高一些：put something under it to raise 抓紧：firmly grasp抬高：lift it up拿稳：hold firm打一下：hit once往外拉：pull outward站稳：stand firm小端：small end大端：large end光滑：smooth粗糙：coarse，rough平面：flat弯曲：bending放松：loosen绷直：stretch tight，draw tight冷却：cooling润滑：lubricate过载：overload功率不足：power is not enough.第4 节钻台与底座钻台：drilling floor钻井班组记录：drilling tour record司钻监视器：driller's monitor司钻控制台：driller's console指重表：weight indicator底座：substructure井队活动房：trailer钻台上值班房：doghouse梯子：ladder第5 节井控操作与防喷器溢流: kick溢流征兆: kick sign气侵：gas cut井喷：blow-out1 次井控the primary well control2 次井控the secondary well control3 次井控the tertiary well control平衡balance超平衡over-balance欠平衡under balance漏失试验leak-off test破裂压力fracture pressure额定压力rated pressure工作压力working pressure防喷器组BOP stack安装（甩下）防喷器组：nipple up(nipple down) BOP stack 分流器diverter万能防喷器：annular preventer，bag preventer单闸板防喷器：single ram preventer双闸板防喷器：double ram preventer（防喷器）闸板：pipe ram变芯闸板防喷器variable bore ram全封式防喷器：blind ram剪切防喷器：shear ram内防喷器Inside BOP投入式单流阀DIBPV（Drop in blowout preventer valve）分流关线diverter line节流管汇choke manifold节流阀choke valve旁通阀standby valve调压阀: Pressure regulator手动节流阀manual choke远程节流阀remote choke井口四通drilling spool变径法兰：adapter flange液压控制阀HCR(hydraulic controller)远程控制系统：koomey unit蓄能器：accmulator压井管线：kill line入口：inlet出口：outlet简易除气器：poor-boy degasser真空除气器：vaccum degasser泥浆池液面纪录仪Pit volume recorder(totallizer)泥浆流动传感仪mud flow sensor泥浆增量Pit gains硫化氢侵入H2S influx加重材料Weighted material氮气Nitrogen乙炔：acetylene氧气：oxygen预冲氮气压力Pre-charge nitrogen pressure地脚螺栓连接Studded connection法兰连接Flange connection箍盘连接Hub connection演习：drill急救演习：first aid drill消防演习：fire drill防喷演习：kick drill泄压: bleed off pressure带刻度压力表: calibrated pressure gauge带刻度容（体）积表: calibrated volume gauge套管鞋: casing shoe上部井眼段top hole section快速钻进地层fast drilling formation压实地层：consolidated formation风化地层：weathered formation钻屑携带能力cuttings carrying capacity浅层气藏shallow gas地层破裂formation to break down压力梯度pressure gradient地层压力formation pressure井口压力wellhead pressure漏失压力leak-off pressure破裂压力fractured pressure井底压力BHP( bottom hole pressure)正常压力normal pressure异常压力abnormal pressure静液压力hydrostatic pressure动态压力dynamic pressure环空压力annular pressure关井钻杆压力SIDPP (shut in drill pipe pressure)关井套管压力SICP( shut in casing pressure)最大关井套管压力maximum allowable surface pressure, MAASP 最初循环压力ICP( Initial circulating pressure)循环结束压力FCP(Final circulating pressure)U 形管原理U-tube principle压井操作killing operation补救措施remedial actions关井后循环circulation under well closed in conditioncl 离子含量chloride contentDc 指数Dc exponent软关井soft shut in硬关井hard shut in第1 次循环first circulation第2 次循环second circulation压井泥浆比重kill mud weight抽吸swab激动surge含气地层gas bearing formation含气页岩gas bearing shale安全增量safety margin记录卡片trip sheet低循环泵速SCR(slow circulation rate)当量泥浆密度EQD(equivalent mud density)当量循环密度ECD(equivalent circulating density)司钻压井法driller’s method等待压井法wait & weight method体（容）积法volumetric method下推压井法bull-heading method不压井下钻：snub in第三章：钻井工程作业部分第1 节钻井事故井喷：blow out井涌：kick井漏：lost circulation坍塌，井壁坍塌：cave in(collapse)出砂：sand production砂桥：sand bridge台阶：ledge键槽：keyseat椭圆井眼：oval shaped hole卡钻：sticking填井：pack-hole封井：packed drilling井下落物：fish大幅度活动钻具试图解卡：work the string and try to free it活动钻具以避免卡钻：move(reciprocate ) the string to avoid being stuck. 打捞：fishing鱼头：top of fish打捞工作：fishing job侧钻：side-tracking侧钻井眼：sidetracking hole水泥窜槽：cement channeling固井失败：cement failure防砂：sand control缓慢开泵并仔细观察返浆情况：slowly start pumping and closely watch the return on the shale shaker 第2 节钻头牙轮钻头：rock bit刮刀钻头：drag bit金钢石钻头：diamond bit镶齿钻头：insert bit铣齿钻头：milled tooth bit喷射钻头：jet bit牙轮：cone钻头装卸器：bit breaker钻头直径：bit diameter钻头寿命：bit life钻头磨损：bit wear钻头型号：bit type水眼尺寸：nozzle size水眼效率：nozzle efficiency钻头接头：bit sub第3 节钻具方钻杆：kelly方钻杆旋扣器：kelly spinner方钻杆旋塞：kelly cock钻具：drilling string钻杆：drill pipe油管：tube钻具组合：drilling assembly扶正器：stabilizer扩眼器：reamer（hole opener）钻铤：drill collar无磁钻铤：NMDC(non-magnetic drill collar) 加重钻杆：HWDP(heavy weight drill pipe) 近钻头扶正器：near-bit stabilizer震击器：jar减震器：shock absorber螺旋钻铤：spiral drill collar键槽破坏器：key seat reamer安全接头：safety joint钻杆刮泥器：drill pipe wiper泥浆动力钻具：mud motor钻柱：drill string涡轮：turbine涡轮钻具：turbo-drill stem立根：stand加厚：upset内加厚：IU(internal upset)外加厚：EU(external upset)内外加厚：internal-external upset丝扣：thread打捞颈：fishing neck母扣：box公扣：pin左旋螺纹：left-hand thread右旋螺纹：right-hand thread正规接头：regular joint贯眼接头：full hole joint内平接头：internal flush joint护丝：thread protector快速护丝：easy protector打捞工具：fishing tool打捞作业：fishing operation打捞篮：junk basket卡瓦打捞筒：overshot打捞杯：junk sub牙轮打捞器：cone fisher套管打捞矛：casing spear打捞矛：fishing spear打捞公锥：male tap(fishing nipple)打捞母锥：female tap(fishing socket)倒扣工具：reversing tool(backing-up tool) 铣鞋：milling shoe铣具：milling tool平底铣鞋：flat bottom mill磁力打捞工具：magnetic fishing tool打捞钩：fish hook气动工具：pneumatic tool减摩短节：friction reduction sub下套管漂浮接箍：casing floating coupling 轴向加压器：hydraulic axial thruster第4 节钻井工程地面作业实用词汇与短语方入：kelly-in方余：kelly-up开钻：spud in作业指令：instruction钻井设计：drilling program井身结构：well schematic岩性：lithology迟到时间：lag time(bottom up)换钻头：change bit甩钻具：laydown drill pipe发生故障：break down安装（拆卸）：rig up(rig down)接头：sub adapter机械手：mechanical arm铁钻工：iron roughneck有故障：It fucked up( something is wrong with it)已修好：it has been fixed马上去：Go there at once请下去：Please go down请上来：Please come up躲开，危险：keep away，danger.请翻译来：Ask interpretor come here，冲洗：wash down井口：well-head一根钻杆（单根）：single三根钻杆组合（立根）：thribble吊蓝：cage(basket)换班：shift change第5 节钻井工程井口作业实用词汇与短语喇叭口：bell nipple出水管：mud return line(flow line)试压杯：cup tester小心滑倒：wet floor, be careful不要往井眼内掉东西：never fall down anything inside hole 我来做：Let me do it带把板手来：Bring a spanner，please带点密封剂：Bring a little sealant(Teflon)，please很快就好了：lt will be finshed right away抬一下：Let's lift it把绳子给我：Give me the rope，please不漏：no leakage电焊：welding气焊：gas welding气割：gas cut栏杆：handrail，gangway rail，railing蒸汽：vapour压缩空气：pressurized (compressed) air注意安全：pay attention to safety别动：Don't move，Don't touch.对准：point out exactly.校正：align裸眼：open hole第四章：钻井液及相关设备第1节钻井液名称泥浆：mud钻井液：drilling fluid完井液：completion fluid修井液：work-over fluid压井液：killing fluid射孔液：perforating fluid隔离液：spacer fluid泥浆处理：mud treatment泥浆处理设备：mud treating equipment饱和盐水泥浆：saturated salt-water mud油基泥浆：oil-base mud高粘度泥浆：heavy viscous mud重泥浆：weighted mud重泥浆压钻杆：slug drill pipe起钻倒返泥浆：we have wet pipeduring POOH 重晶石：barite纯碱：soda ash高岭土粉：koaline powder云母片：mica sheet增粘剂：viscosifier稀释剂：diluent (thinner)稳定剂：stabilizer (stabilizing agent)烧碱：caustic soda稀释dilution, thinning水泥凝固cement setting第2 节钻井液设备离心泵：centrifugal pump振动筛跑泥浆：mud overflow shale shaker筛出：shake out混合泵：mixing pump混合漏斗：mixing hopper搅拌器：mud agitator泥浆抢：mud gun岩屑：cuttings沉淀：settle沉积物：deposit吸入：suction吸入罐：suction pit泥浆天平：mud balance游码：slide weight支点：fulcrum刀口：edge调整，校正：adjust粘度计：viscometer第3 节钻井液处理剂包，袋：sack粘土：clay膨润土，般土：bentonite钠：sodium钙：calcium氯：chloride氯化钙：calcium chloride石棉：asbestos分散：dispersal表面活性剂：surface-active material铁络盐：lignite单宁：tannin羧甲基纤维素：carboxymethyl celluose CMC 木纤维：xylogen石灰：lime二氧化钙：calcium oxide粉末：powder薄片：flake溶解：dissolve延迟，妨碍：retard处理剂，添加剂：additives缓凝剂：retarder支撑剂：proppant乳化剂：emulsifier润湿剂：wetting agent稳定剂：stabilizing agent除钙剂：calcium remover降失水剂：filtration-reducing agentPH 值控制剂：PH control additive润滑剂：lubricant消泡剂：defoamer agent破乳剂：emulsion breaker洗涤剂：detergent防膨胀剂：anti-swelling agent粘土稳定剂：clay stable agent稀释剂：thinner封堵剂：plugging agent抑制剂：inhibition agent暂堵剂：temporary plugging agent解堵剂：plugging removal堵漏剂：LCM (lost circulation material)水敏地层：water-sensitive formation分散：dispersal水泥浆：cement slurry流变性：rheological characteristics稳定性：stability稠化时间：thickening-time低密度水泥浆：low-density slurry油气层保护：reservoir protection高渗透性：high-permeability砾石：gravity悬浮：suspension固化：solidification.防膨胀：anti-swelling高凝高粘度：high condensation and viscosity 无毒的：non-poisonous无荧光：non-fluorescence钻井液性能参数Specificaitons of Drilling Fluid 含水：water content密度：density厚度：thickness粘度：viscosity塑性粘度：plastic viscosity含砂量：sand content屈服：yield屈服点：yield point屈服强度：yield strength剪切速率：shear rate剪切强度：shear strength剪切应力：shear stress稀释：dilute适用温度：safe temperature初始切力：initial gel strength终切力：ten-min gel strength触变性：thixotropy剪切稀释：shear thining液体浓度:concentration泥浆柱：mud column层流：laminar flow涡流：turbulent flow气泡：bubble第五章：钻井相关作业第1节取芯部分岩心：core取心钻头：core bit取心筒：core barrel内岩心筒：inner barrel外岩心筒：outer barrel岩心爪：core catcher取心工具：corehandling tools取心收获率：core recovery rate取样器：sample blob取样盒：sample box样品筒：sample chamber取样工：sample catcher取样间隔：sample interval井壁取心：side-wall coring井壁取心枪：side-wall coring gun取芯失败：coring failure第2 节固井部分固井：cementing完井：well completion水泥：cement井口：wellhead井口压力：well head pressure井口回压：back pressure on the well head套压：casing pressure导管：conductor表层套管：surface casing技术套管：protective casing(intermediatecasing) 油层套管：production casing尾管：liner尾管悬挂器：liner hanger通径轨：rabbit封隔器：packer联顶节：landing joint套管柱casing string套管下部结构(含套管鞋、浮箍)：casing track(including casing shoe, float collar) 套管扶正器：centralizer止退环：stop collar口袋：pocket( rat hole)环空注水泥作业：top cement job碰压：bump plug隔离液：spacer分级箍：stage collar水泥粘结强度strength of cement bond套管钳：casing tongs套管接箍：casing coupling套管头：casing head散装水泥：bulk-cement水泥浆：cement slurry插管注水泥：stab in cementing插入密封接头：stab in adapter分级注水泥：stage cementing先行水泥浆：lead cement slurry末端水泥浆：tail cement slurry促凝剂：accelerator替浆：displace with mud水泥面：top of cement固井管线：chicksan line(cementing line)灰罐：silo(bulk tank)候凝：WOC(wait-on-cement)挤水泥：squeeze cement水泥塞：plug第3 节固井水泥浆名称和参数超细水泥浆：ultrafine slurry普通水泥浆：normal slurry纤维水泥浆：fiber-reinforced cement slurry膨胀水泥浆：expanding cement slurry低密度水泥浆：low-density slurry水泥体积收缩：cement volume contraction水泥浆水化期间：cement slurry hydrating period 水泥胶结质量：cement sheath bonding quantity 失水率：the rate of water loss析水：liberate water稠化时间：thickening time凝固强度：cementation strength渗透性：permeability，膨胀率：expansion rate压缩强度：compression strength流动性：mobility第4 节测井部分电测：wireline logging测井解释：logging interpretation随钻测井：LWD(logging while drilling)测井电缆：logging cable测井工具：logging tool自然电位测井：spontaneous potential log感应电测井：induction electrical survey双感应测井：dual induction-laerolog中感应测井：medium induction log数字记录：digital record照相记录：photographic recording放射性测井：radioactivity log声波技术：acoustic wave technology仪器耐温：the temperature resistance of the instrument仪器耐压：pressure resistance of instrument油气比：GOR (gas oil ratio)第六章：井下作业常用短语修井：work-over修井工具：work-over tool井下操作：down-hole operations.产层污染：pollution of pay zone增产措施：stimulations压裂和酸化：fracturing or acidizing酸化处理：acid treatment人工压裂：artificial fracturing重复压裂过程：repetition presses for fracturing，压裂车：fracturing truck sets压裂后反映：post-fracture response固体和液体添加泵：solid and liquid additive pump泵交联：pumping cross link交联剂：cross-linking agent排量：discharging三维压裂：three-dimension fracturing对压裂参数的监控、分析和解释：real time monitoring，analyzing and interpreting for fracturing operation parameters压裂操作：fracturing operation压裂规模：fracturing scale化学吞吐：chemical disposal乳化降粘：emulsification declining viscosity增注：augmented injection.注水：water-injection裸眼砾石填充完井：bore hole gravel packer completion.开窗铣锥：open-window mill prick，开窗斜向器：open-window inclined implement碳酸盐岩：carbonate reservoir第七章：海上钻井作业¨海上钻井：offshore drilling陆地钻井：on-land drilling海滩：sea beach浅海：shallow sea海底管线：sea-bottom pipe海底电缆铺设：setting cable under sea-bottom平台安装：platform installation钻井平台：drilling platform顺风：tail wind逆风：against the wind摄氏零下…度：belo w…degree centigrade启锚：weigh anchor抛锚：drop anchor拖航：drag对讲机：intercom，walkie-talkie上吊茏：Please get on the liftbasket救生衣：life jacket晕船：sea sick控制速度：Control the speed货已送抵：The goods has arrived货物验收：Please check and accept the goods在不远处：Not far from here不方便：lt's not convenient有危险：lt's dangerous防污染：prevent pollution没情况：Nothing happened.第八章：定向井部分定向井：directional well造斜点：ＫＯＰ（kick off point）最大井斜角：maximum hole inclination增斜段：building up section稳斜段：holding section降斜段：drop off section井眼尺寸：hole size长、中、段半径：long，medium and short radius 裸井段：the open hole section水平段：horizontal section固井段：cementing section井斜角测量点：angle point水平位移：horizontal departure(displacement)井眼轨迹：wellbore trajectory优化控制：optimum control筛管：screen pipe长封固段固井：long intervals cementing丛式井：cluster well斜向器：whipstock第九章：石油现场机械传动与机械设备第1 节：动力与传动柴油机：diesel发电机：generator直流（交流）电动机：DC（AC）motor交流电：A.C （alternating current）直流电：D.C （direct current）变压器：transformer传动轴：driving shaft从动轴：driven shaft空调机：air conditioner空气压缩机：air compressor应急发电机组：emergency generator消防水泵：fire pump配电间：distrubution room电动潜水泵：ESP(electrical submersible pump) 锅炉：boiler蒸汽：vapour气压不足：The airpressure is poor操作有问题：Operation is not good电压正常：Voltage is all right绝缘不好：The insulation is bad触电：electric shock温度太高：The tempreture is too high接地：ground短路：short circuit按红色钮：Please push the red button打开：open，turn on，switch on关闭：close，turn off，switch off风扇：fan爬上去：climd up跳下来：jump down接住：catch it拿稳：hold tight平方米：square meter立方米：cubic meter加工：process三项交流电：three-phase AC气罐：air tank偶合器，联轴节：coupling链轮：sprocket链条：chain皮带：belt链条驱动：chain drive皮带驱动：belt drive第2 节机械加工与设备对准，使…成一线：align周围的，环境的：ambient模糊，含糊，不明确：ambiguity退火的：annealed淬火：quench回火：temper阳极：anode阴极：cathode含水的，水的：aqueous装配：assembly增大，增加，增益：augment侧向间隙：back-lash电木，（绝缘）胶木：Bakelite批量生产：bulk production轴承：bearing锥齿轮，伞齿轮：bevel gear（刮刀，刃，叶片：blade坯料：blank吹风，爆炸，喷砂机：blast滑轮组：block and tackle浮子，摆锤：bob镗床，镗孔刀具：borer内孔加工，镗孔：boring瓶颈，薄弱环节：bottleneck平衡点，盈亏临界点：breakeven point 型坯：briquette拉床，铰孔机：broacher拉削，扩孔：broaching大齿轮：bull gear碰撞，曲折，拐点：bump缓冲器，减震器：bumper擦亮，光亮：burnish去毛刺：burring凸轮，偏心轮：cam凸轮轴：camshaft铸造：cast触媒，催化剂：catalyst空化作用：cavitation内腔，空穴，（铸造）型腔：cavity陶瓷的，陶器的，陶瓷制品：ceramic 铁屑，金属屑：chip凿子，扁铲：chisel钳：clamp障碍（物），阻塞（物）：clog离合器：clutch罗盘，指南针：compass凸型的：convex凹型的：concave外形，轮廓；结构，构造：configuration锥形的，锥状的，锥体：conical传送装置，运输机，传送带：conveyor波纹；使成波状：corrugation曲柄，曲拐：crank曲轴：crankshaft蠕动，蠕变：creep圆筒，圆柱体；液缸:cylinder仪表盘，控制板：dashboard静载：dead load碎片：debris模具，钢型，冲模：die模锻：die forge压铸的，模铸的：die-cast不导电的，电解质（的）：dielectric差动齿轮，差速齿轮：differential gear扩散，弥漫：diffusion修饰，打磨，使表面光洁：dress钻床：drill press染色，着色；染料：dye电解质：electrolyte椭圆，椭圆体：ellipse金刚砂：emery侵蚀，冲蚀：erosion蚀刻：etch排出，排气；废气：exhaust消音器：muffler爆炸物，炸药；爆炸（性）的：explosive挤压（成形）；挤出，压出：extrude平面加工：facing测隙规：feeler gauge膜：film精加工：finish柔性的，能变形的，灵活的，适应性强的：flexible 软盘：floppy disc硬盘：hard disk车床：lathe流程图：flow chart起伏，波动：fluctuation开槽，切槽：fluting飞轮：flywheel锻造：forge支点，支轴：fulcrum（龙门）起重机：gantry几何学：geometry花岗岩，花岗石：granite石墨：graphite润滑脂：grease磨碎，研磨，磨削加工：grinding槽，沟，企口：groove陀螺仪，回转仪：gyroscope主轴箱：headstock螺旋形的，螺线：helical螺旋齿轮，斜齿轮：helical gear六角形（的）：hex万向接头，万向联轴节：hooke (cardan) joint,flexible joint 削弱，损害：impair冲击，脉冲：impulse测斜仪：inclinometer（刻度盘上的）指针，（铣床）分度头：index铸模，锭：ingot间歇的，断续的：intermittent内在的，固有的：intrinsic离子：ion夹具，夹紧装置，钻模：jig铰链，关节，肘关节，转向节：knuckle搭接，重叠；研磨，精研，抛光：lapping心轴，紧轴，芯棒：mandrel铣削加工：milling铣刀：milling cutter铣床：milling machine混合，混合物，混合气：mixtrue小孔，注油孔，喷嘴：orifice坑，池，孔：pit枢轴，旋转中心，支点：pivot气动的，气体的，风力的：pneumatic泊松比：Poisson’s ratio抛光：polish细孔，微孔，空隙：pore多孔性，空隙度，气孔，砂眼：porosity。
钻井专业词汇
绪论勘探exploration 开发production顿钻钻井cable drilling旋转钻井Rotary drilling 转盘钻井Rotary drilling顶驱钻井top drive drilling 井下动力钻井hole bottom power drilling 涡轮钻具钻井turbine drilling 螺杆钻具钻井screw drilling旋转钻井钻机Rotary Rig 动力系统(Power System)旋转系统(Rotating System) 提升系统(Hoisting System)循环系统(Circulating System) 井控系统(Well Control System)监测系统 (monitoring System)井架derrick 天车crown block 游动滑车travelling block大钩hook 大绳drilling line 绞车drawworks泥浆泵mud pump泥浆池mud pit 振动筛Vibration Screen防喷器组blowout preventers 地面管汇surface pipeline遥控面板remote control pane 压井管汇kill line钻前准备drill preparation 钻进drilling固井well cementation 完井well completion直井straight/vertical well 定向井directional well水平井horizontal well 浅井shallow well中深井medium-deep well 深井deep well超深井ultra deep well 特超深井super/extra deep well探井exploration well 采油井production well多底井multi-bore well 丛式井cluster well or multiple wells第一章沉积岩sedimentary rock 变质岩metamorphic rock 岩浆岩magmatic rock 岩石的物理机械性质physical-mechanical properties of rock岩石的弹性模量elastic modulus of rock岩石的泊松比rock Poisson’s ratio岩石的切变模量shear modulus of rock抗拉伸强度tension resistance 抗压缩强度 compressive resistance抗剪切强度 shearing resistance 抗弯切强度 bending resistance弹性elasticity 脆性岩石 brittle rock 塑性岩石plastic rock岩石塑性系数rock plasticity coefficient地应力in situ stress 围压confining pressure 有效应力effective stress 压持效应chip hold effect 岩石的可钻性drillability岩石的研磨性rock abrasiveness地层水formation brine比重specific gravity静液压力hydrostatic pressure钻井液压力drilling fluid column pressure 孔隙压力pore pressure地层压力formation fluid pressure地层破裂压力formation fracture pressure上覆岩层压力overburden pressure 基岩应力matrix stress压力梯度pressure gradient 异常压力abnormal pressure压实作用compaction 欠压实作用 undercompaction function机械钻速法penetration rate method d指数法d-exponent methoddc指数法 dc-exponent method 声波时差法acoustic travel time岩石硬度rock hardness漏失试验法leak-off test第二章刮刀钻头（blade bit）牙轮钻头（cone bit）金刚石钻头（diamond bit）天然金刚石钻头（ＮＤ）natural diamond人造聚晶金刚石钻头（ＰＤＣ） polycrystalline diamond compact bit热稳定聚晶金刚石钻头（ＴＳＰ）thermally stable polycrystalline diamond bit水力结构hydraulic structure 超顶（cone overhang）复锥（offset axis）移轴（multiply cone ）钻头的经济指标(economic indicators of bit)钻头进尺(bit footage) 钻头工作寿命(bit operating life)钻头平均机械钻速(bit average rate of penetration)钻头单位进尺成本(cost per singer footage)第三章浮力 buoyancy 钻柱drill stem/string 钻铤drill collar钻杆drill pipe 方钻杆kelly钻头bit 稳定器stabilizerHWDP-厚壁钻杆（Heavy wall drill pipe）复合钻柱combination string中性点neutral point 最大安全静拉力maximum safety static tension第四章钻井液drilling fluids/mud 水基钻井液water-base drilling fluids淡水钻井液fresh-water drilling fluids 低固相钻井液low solids fluids API滤失量API filtration 分散相(dispersion phase )分散介质(dispersion medium)化学处理剂(Chemical treating agent)滤失filtration 滤饼filter cake 含砂量sand content钻井液固相含量solids content in drilling fluids流变方程rheological equation牛顿流体Newtonian fluid 非牛顿流体non- Newtonian fluid塑性流体plastic fluid 幂律流体power law假塑性流体pseudo plastic fluid 膨胀液体expansion fluid钻井液流变性drilling fluids rheology 漏斗粘度funnel viscosity触变性thixotropic behavior 剪切稀释特性(shear thinning)静切力gel strength 动切力yield value 塑性粘度Plastic Viscosity动塑比ratio of yield value to plastic viscosity初切力initial gel strength 终切力10-minuto gel strength固相控制solid control 钻屑cutting 砂sand 泥silt压差卡钻(differential pressure sticking)井漏(lost circulation )井塌(borehole collapse) 钻井液污染(drilling fluid contamination ) 第五章井眼轨道(well trajectory)井眼轨迹(well track)井深Measure Depth 井斜角inclination/deviation angel方位角azimuth angle井斜变化率rate of deviation 方位变化率rate of azimuth井眼曲率hole curvature垂深True vertical depth(TVD)水平投影长度horizontal projection length (hole deviation)水平位移horizontal displacement平移方位角(translational azimuth) N坐标和E坐标(N-coordinate & E-coordinate)视平移(apparent horizontal displacement )水平投影图(horizontal projection)垂直投影图(vertical projection)垂直剖面图(vertical cross section )直井段(Vertical section)ok造（增）斜段(build section) kb稳斜段(hold section ) bh降斜段(drop section) hd目标点(target point)靶区及靶区半径(target area) rt 靶心距(off-target distance) St造斜点(kick off point) k 二维定向井Two-dimensional directional well三维定向井Three-dimensional directional well第六章喷射式钻头jet bit 射流喷速jet velocity射流冲击力jet impact force 射流水功率jet hydraulic-power钻头压降bit pressure-drop钻头水功率bit hydraulic horse-power钻井泵的工作状态the working regime of drilling pump额定泵压rated pump pressure额定功率rated pump power循环压耗circulating pressure loss 优选标准optimization standard钻压weight on bit转速rpm-revolution per minute 排量rate of flow 进尺footage 喷嘴nozzle钻速方程drilling rate equation /model第七章测斜deviational survey 平均角法average angle method曲率半径法radius of curvature method 井斜well deviation满眼钻具packed hole assembly 钟摆钻具pendulum assembly钟摆力pendulum force井底动力钻具bottomhole motor转盘钻 rotary drill 工具面角tool face orientation装置方位角tool face azimuth 定向方位角Directional azimuth反扭角reactive torque angle第八章地层井眼系统的压力平衡 balance of formation-borehole system地层压力当量钻井液密度equivalent drilling fluid density钻井液当量循环密度equivalent circulating density波动压力（激动压力）surge pressure 抽汲压力swabbing pressure井侵 influx 溢流overflow 井涌kick 井喷well blowout地下井喷underground blowout 井喷失控out of control for blowout正压差positive differential pressure负压差negative differential pressure平衡钻井balanced drillin g 欠平衡under balanced drilling近平衡near balanced drilling 过平衡over balanced drilling关井shut in 防喷器blow out preventer 地面管汇surface drill pipe环形空间annulus 压井killing well 硬关井hard closing软关井soft closing 压井方法killing well method工程师法（等待加重量法）engineer’s method司钻法（二次循环法）driller’s method第九章套管程序casing program导管conductor 表层套管surface casing技术套管intermediate casing strings 生产套管production casing 尾管line 钻井尾管drilling liner 生产尾管production liner套管接箍casing coupling套管柱casing string 前置液ahead fluid隔离液spacer fluid 冲洗液flushing fluid套管的外载荷outside casing load 套管内压力burst套管外挤压力collapse pressure 套管轴向力axial load套管强度casing strength 套管抗挤强度collapse resistance套管抗拉强度tensile resistance 套管抗内压强度burst resistance完井方法completion methods 裸眼完井法open hole completion先期裸眼完井法initial open hole completion后期裸眼完井法final open hole completion射孔完井法perforation completion衬管完井法slotted liner completion砾石充填完井法gravel pack completion固井质量cement job quality 固井质量评价cement evaluation窜槽cement channeling 顶替效率displacement efficiency尾管固井drilling liner cementing 尾管悬挂器drilling liner hanger井口装置wellhead 油管头tubing head 套管头casing head采油树Christmas tree稠化时间thickening time 凝结时间setting time。
石油钻井专业英语词汇
目录第一节钻井英语单词 (2)第二节井场用语，钻井常用短语及句子 (10)第三节钻井泥浆术语 (29)第四节常用安全术语 (31)第五节钻井设备英语 (33)第六节石油钻井英语情景会话 (40)附录一：平台人员、作业者及服务公司人员名称 (47)附录二：主要设备名称 (48)附录三：钻具、井口工具、打捞工具名称 (52)附录四：材料和工具名称 (53)附录五：常用缩写形式 (55)第一节钻井英语单词drilling crew 钻井队drill floor,rig floor,floor 钻台drawworks 绞车well-site, rig-site 井场rig manager 平台经理DC (drill collar) 钻铤drilling engineer 钻井工程师DP (drill pipe) 钻杆toolpusher 带班队长rotary table 转盘driller 司钻assistant driller 副司钻derrickman, monkeyman 井架工roughneck, floorman 钻工roustabout 场地工liner 缸套motor fire man 司机（motorman）wellhead 井口circulation & solid system 循环固控系统machinist 机械师,机工,机械大班electrician 电器师,电工,电器大班operation program 作业程序(指令) cathead 猫头caravan 营房，大篷车tong 大钳elevator 吊卡well depth 井深slip 卡瓦makeup 上扣spud in 开钻breakout 卸扣ROP (rate of penetration),drilling speed, penetration rate 钻速trip 起下钻diesel-engine 柴油机loss circulation 井漏，循环漏失working uniform 工作服brake handle, brake bar 刹把water well condition 水井井况circulating tank, circulation tank 循环罐normal drilling 正常钻进reserve tank 储备罐parameter 参数trip tank 补给罐，尖底罐, 起下钻泥浆罐（起下钻计量罐）rotary speed 转盘转速（转速）shale shaker 振动筛pump pressure 泵压WOB (weight on bit) 钻压mesh 目,网孔;啮合,编织torque 扭矩screen cloth 筛布displacement 排量safety meeting 班前会pump stroke 泵冲shift exchange 交班、（倒班）mud pump 泥浆泵master 师傅,主人;征服,控制,精通in charge of 负全责,经营,照顾obtain 获得,得到according to 根据,依照normal 正常的,正规的,标准的introduce 介绍,传入,引进,提出progress 前进,行进,进展supervisor 监督location 井场,井位inspection 检查,考察,验收cellar 方井soild (control) system 固控系统waste pit 污水池、废水池Top Drive (Drilling System)顶(部)驱(动)钻井系统Project Department 项目部on duty 值班modify 整改、修改clinic 医务室electic al rig 电动钻机disconnect 拆开,分离,断开pipeline 管线order 指令,命令,顺序Company 公司,甲方Operator 业主,甲方Contractor 承包商,乙方pump house 泵房schedule 时间表,进度表size 尺寸,大小,尺码information 通知,信息,资料equipment 设备,装备,器材instruction 指令,指示,说明书SCR house 可控硅房replace 更换,替换,代替brake shoe 刹车块wear out 磨损safety 安全,保险,安全设备fax 传真guy 家伙,人standpipe 立管Campsite 营地crownblock 天车traveling block 游车dog-house 司钻休息室(钻工值班房)rat hole 大鼠洞mouse hole小鼠洞spudding inspection 开钻验收fill in 填充catwalk 狭窄的过道,高空走道;高台,天车台casing float collar 套管浮箍casing float valve 套管浮阀casing guide shoe 套管引鞋cement水泥,注水泥,结合剂,胶结剂plug 插头safety pin安全销glove手套quick-connector快速接头fire exting u isher灭火器stretcher担架First Aid紧急救护control board控制板weight mdicator指重表rotary torque indicator转盘扭矩表sling吊绳绳套deadline anchor死绳固定器brake system刹车系统drum滚筒safety line保险绳safety belt安全带hydraulic tong液压大钳slip卡瓦（和上面的重复）elevator吊卡（和上面的重复）bit breaker钻头盒chain tong链钳pipe tong管钳wrench板手pliers钳子、老虎钳scissor剪刀cable slot电缆槽vacuum degasser真空除气器butterfly valve蝶阀desilter除泥器desander除砂器degasser除气器mud gun泥浆枪agitator搅拌器leakage漏,泄漏,渗漏barite重晶石hopper漏斗piston活塞union由壬fuel tank燃油罐、高架罐remote control station远控房BOP stacks防喷器组kill line 压井管线choke line节流管线blowout preventer防喷器annular环空ram闸板low pressure低压fire blanket消防毯fire sand防火砂kitchen厨房storeroom储藏室bathroom卫生间(浴室)spudding date开钻日期spudding time 开钻时间string钻柱BHA（bottom hole assembly）井下钻具组合drilling jar随钻震击器drill box钻杆盒drilling program钻井程序、钻井指令drilling fluid钻井液mix up混和、调配、混淆mud material泥浆材料LCM（lost circulation material）堵漏材料、堵漏剂mud engineer泥浆工程师day tour白班night tour夜班drilling progress钻井进度routine inspection例行检查、日常cave in塌陷、塌下、井壁坍塌loss漏失kick井涌hole section井段casing setting depth套管坐封深度downhole problem（trouble）井下事故(井下复杂情况)undergauge 缩径tight hole井径缩小的井眼tight spot （井径）缩小点、缩小段footage钻井进尺formation地层、岩层、构造、组织make up a joint接单根（立柱）sticking 粘附、刺、卡钻sticking point卡点free point解卡点？？hook weight悬重unfreeze解卡back-off倒扣fishing 打捞sidetrack侧钻back reaming倒划眼soak oil泡油soak releasing 泡解卡剂slough off坍塌ream down划眼borehole operation井下作业deviational survey 井斜测量（测斜）make a trip 起下钻bouncing 跳跃的、大的、重的、跳钻bit bouncing 蹩跳bit balling 泥包钻头cutting 切削、切割、切屑、钻屑cutting sample 砂样mud logging 综合录井sandstone 砂岩Pooh(pull out of hole) 起钻RIH(run in hole)下钻junk 落物、金属屑、碎物junk sub 打捞（落物）接头scrape 擦、刮、擦痕、刮掉bit gauge 钻头规centralizer 扶正器hold pressure 蹩压day rate 日费standby rate 等待日费、待命费run casing下套管cementing operation固井作业drift casing套管通径？？clean thread洗扣geologist地质师、地质学家casing shoe套管鞋thread protector护丝casing tong套管钳wiper trip通井rigid centralizer刚性扶正器guide shoe引鞋float-collar浮箍accident事故、意外事件slurry水泥浆WOC（waiting-on--cement）候凝期nipple up安装（防喷器）primary cement job正注固井wireline log电测test pressure 试压International practice国际惯例choke manifold节流管汇lay down the string倒钻具nut螺母bolt螺栓、螺钉screw bolt螺栓、螺杆pipe ram半封闸板shut-down停工HWDP (heavy weight drill pipe) 加重钻杆calibrate 校正、定标judgment 判断bleed off lin e排砂(排放)管线commence 开始、着手isolate 隔离、隔绝、绝缘welding 焊接、压实、压结mud property 泥浆性能MW(mud weight) 泥浆比重mud density 泥浆密度funnel viscosity 漏斗粘度PV(plastic viscosity) 塑性粘度well control drill 井控演习、防喷演习increase 增大、增加、增大decrease 减少、降低；减少之量pressure gauge 压力表casing pressure 套(管)压(力)choke valve 节流阀coring operation 取心作业hole collapse井壁坍塌pressure surge 压力激动、压力涌动bump pressure 碰压cement head 水泥头re v erse circulation 反循环cement 水泥，注水泥；结合剂；粘紧，粘牢(重复)cement accelerator 水泥促凝剂cement hardener 水泥速凝剂, 水泥硬化剂cement head (注) 水泥头cementing jobs 注水泥作业cement job 固井作业cement squeeze 挤水泥bonus 奖金,红利completion job 完井作业hand pump 手摇泵,手压泵workshop 车间,工场nipple down 卸下nipple up 装上,接上,装配,安装(重复)ID (inside diameter) 内径torque-on-bit 钻头扭矩tubing bonnet 油管头tubing hanger 油管悬挂器, 油管挂tubing joint 油管接箍landing head (悬挂油管用)油管头,(油管)联顶头landing joint 联顶节[下套管或油管联顶时用] TBG (tubing) 油管spacer fluid 封隔液mud logging unit 综合录井仪cooperation 合作,协作sample sack 砂样袋engage 从事;啮合deadline anchor 死绳固定器,死绳锚(重复)drilling cost 钻井成本evaluate 评价,估价,求…的值in advance 预先overpressure 过压，超压力swab 抽汲eliminate 排除,消除pipe bouncing 钻具蹩跳drill string failure 断钻具twist-off 脱扣horizontal well 水平井vertical well 垂直井stainless steel 不锈钢anticline 背斜porosity 孔隙度potential 潜在的,可能的; 潜能,潜力densimeter 密度计communication 传达,信息,交流,通讯hook velocity 大钩速度verify 检验,查证,核实confirm 确定,批准,印证incredible 难以置信的round trip 起下钻resume normal drilling 恢复正常钻进goal 目的,目标understanding 理解,认识,谅解kill operation 压井作业wireline [electric] log 电测井GR 自然伽玛scrap iron 铁屑cotton yarn 棉纱paint 油漆cavern 大山洞,大岩洞,溶洞,穴fossil 化石;陈腐的,守旧的gas-bearing 含气的water-bearing 含水的DST(drill-stem test) 中途测试, 钻杆测试water loss 失水flow pressure 流动压力daily output 日产量target zone 目的层finishing drilling 完钻thermometer 温度计re v er s e circulation 反循环build up 建造，安装；压力增加，压力恢复build up a joint??Well Control & Drill Procedures井控措施及防喷演习程序LIST OF ABBREVIATIONS缩写表BHP - Bottom-Hole Pressure 井底压力BOP - Blow out Preventer 防喷器（重复）CDPP - Circulating drill pipe pressure 循环钻杆压力CP - Casing pressure 套管压力（重复）CSG – Casing 套管（重复）DC - Drill collar 钻铤DP - Drill pipe 钻杆ECD - Equivalent circulating density 当量循环密度EMW - Equivalent Mud Weight 当量泥浆比重FCP - Final Circulating Pressure 最终循环压力Gm – Mud weight 泥浆比重HPHT - High pressure high temperature高压高温HWDP - Heavy Weight Drill Pipe加重钻杆（重复）ICP - Initial Circulating Pressure初始循环压力LOT - Leak-Off Test地漏测试MAASP - Maximum Allowable Annular Surface Pressure最大容许环空表面压力MD - Measured depth测量深度MEMW - Maximum equivalent mud weight最大当量泥浆比重Ps - Static pressure静压力Q - Flow rate 流量ROP - Rate of penetration机械钻速SICP - Shut-in Casing Pressure关井套压SIDPP - Shut-in Drill Pipe Pressure关井钻杆压力TVD - Total vertical depth垂直总深kill and choke lines 压井和节流管线kill fuild 压井液killing well 压井kill job 压井作业kill line压井管线kill rate 压井排量kill string 压井管柱kill-weight-fluid 加重压井液，高比压井液operating skill 操作技巧view point 观点engage in 从事，啮合primary control 首要控制，一次井控secondry control 二等控制，二次井控tertiary control第三位控制，三次井控safety margin 安全系数circulate out循环带出wildcat 探井pressure surge 压力波动，压力骤增（重复）Kick Control Sheet 井涌控制表circulating bottoms up循环井底至井口的泥浆行程active mud system在用泥浆系统fill the hole 灌满井眼human failure 人为事故differential pressure压差additive 添加剂obstruction阻塞，阻挡evidence 迹象，证明lower Kelly cock 方钻杆下旋塞upper Kelly cock 方钻杆上旋塞stripping 强行起下钻potential 潜在的，可能的；势，位shut-in procedures 关井程序，关井步骤soft shut-in procedures 软关井程序with a careful eye on留心saver sub 保护接头pipehandler 管子操作装置Driller’s Method 司钻法water-based system 水基体系implement 执行overcome 克服Daily Drilling Report 钻井日报表up-to-date 现代化的，最新（式）的，当今的chilksan line活动弯头管线H2S ( hydrogen sulfide) 硫化氢Muster point (Muster board) 紧急集合点（紧急集合点标识牌）Wind sock 风向标SCBA (self-contained breathing apparatus) 呼吸器Oxygen, acetylene 氧气，乙炔Alarm 警报Ambulance 救护车Emergency team 应急小组Fire pump, Fire drill, Fire hose, ax, rope 消防泵，消防演习，消防水龙带,消防斧，消防绳JSA (job safety analysis)工作中安全因素分析HSE (health, safety and environment) 健康，安全，环保Escaping route 逃生路线Inflammables 易燃物品Work Permit (Permit to Work) 工作许可（证）Safety meeting for running casing, liner, electric log 下套管，尾管，电测安全会PPE (personal protection equipment) 劳保用品Special operation 特殊作业Vehicle inspection 车辆检查Housekeeping 打扫卫生Crane 吊车MSDS（material safety data sheet）泥浆药品安全使用手册first aid box 急救箱Helmet安全帽Safety glasses 护目Fall arrester 防坠器VIS (viscosity) 粘度PV (plastic viscosity) 塑性粘度（重复）YP (yield point) 屈服粘度(流动点) Gels (gel strength) 静切力(胶凝强度)low viscosity低粘high viscosity (hi-vis)高粘lightweight low-viscosity mud低比重低粘泥浆water tank水罐caustic soda 烧碱dangerous 危险sand trap 沉沙罐、锥形罐trip tank 计量罐pill tank加药罐waste pit 排沙池fluid loss 失水第二节井场用语，钻井常用短语及句子钻井（Drilling）1、Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业。
石油钻井英语常用专业词汇
钻井英语常用专业词汇钻井监督foreman队长rig manager（带班）队长toolpusher司钻driller钻工roughneck钻工floorman井架工derrickman泥浆工mudboy油层oil zone地层formation页岩层shale formation地层流体formation fluid岩屑cutting井场wellsite泵房pump area(pump house) 值班房doghouse工具房tool house工具箱tool box井bore hole野猫井wildcat well定向井directional well手工具hand tool公锥taper tap母锥box bell 活动扳手monkey wrench活动扳手adjustable wrench割枪cutting torch打捞工具fishing tool钢卷尺tapeline大钢卷尺steel band tape大钳tong手钳子hand vice手钳子台钳bench vice链钳chain tong内钳lead tong外钳back-up tang液压大钳hydraulic tang套管大钳casing tang榔头hammer螺栓bolts螺丝刀screw driver钢丝绳wire line兜绳mule line安全带safety straps接头sub倒大绳slip and cut the drilling line六方的hexagonal转盘rotary table短路short circuit切断电源stitch off the electricity电路通circuit complete变压器transformer焊条welding rod死绳固定器dead line anchor单点照相测斜仪single-shot inclinometer柴油机engine加热器heater转速revolution高压油泵high pressure fuel pump压风机air compressor电动的electric机动的mechanical泥浆比重计mud scale泥浆仪器mud instrument指重表weight indicator转速表tachometer乙醚ether泥浆drilling fluid钻井液drilling fluid重泥浆slug pipe盐水泥浆salt water mud化学处理剂chemical treating化学药品chemicals泥浆药品mud material粘土clay解卡剂pipe lax material井架derrick钻机（绞车）drawwork电动钻机electric rig钻台rigfloor钻台drillfloor二层台monkey board钻头bit钻柱drill string钻杆drill pipe加重钻杆heavy weight drillpipe方钻杆Kelly大鼠洞rathole震击器jar天车crown block流动滑车traveling block水刹车hydraulic brake刹把brake bar吊卡elevator套管丝扣casing threads护丝thread protectors接头sub配合接头crossover配合接头X-over提升短节lifting sub提升短节lifting nipple提升短节elevator plug卡瓦slip螺旋钻铤spiral collar无磁钻铤柔性短节flex joint滚子扶正器reamer绷绳锚dead men绷绳锚guy anchor绷绳guy line绳卡guy clamp高速离合器high drum clutch 泥浆泵the mud pump活塞piston停泵stop the pump缸套liner拉杆rod拉杆盘根rod packing缸套盘根liner packing高压管线high pressure line 立管standpipe反循环reverse circulation 闸门valve保险凡尔pop-off valve凡尔座valve seat刺washing out取出器puller甩钻具lay dawn drill stem 接大钻具pick up BHA丝扣油dope丝扣thread单根 a joint接卸单根make up/break down a joint 下部钻具结构bottom hole assembly(BHA)再上一扣Make it up one more thread钻头盒bit breaker泥浆罐mud tank搅拌机agitator振动筛布shaker screen停泵circulating固控设备solid control equipment泥浆清洁器mud cleaner闸刀盒switch box离心机centrifuge机厂machine shop动力装置power unit除气器degasser除气器poor-boy除气器gas buster泥浆稠the mud is viscous除砂器desander套管工具casing tool套管大钳casing tang吊卡elevator灌泥浆管线fill up line套管内径规casing rabbit套管头casing head联顶节landing joint套管护丝casing screw protector套管卡瓦casing slip扶正器casing centralizer引鞋casing float shoe回压凡尔casing float collar刮管器casing scraper固井车cement truck防喷器blowout preventor控制台control device井喷blowout防喷系统BOP system汇流阀manifold vlove落鱼fish迟到时间bottom up打捞工具fishing tool卡瓦打捞筒overshot回波探伤仪echo-ranger随钻测斜仪directional orientation tool井下仪器downhole instrument仪器读数instrument readings吊测wire line survey装好定向工具rig up steering tool上提下放钻具Pick up/slack off the string安装设备install equipment开钻start working开钻spud in the well下钻run in hole起钻pull out of hole起钻trip out of hole短途起钻 a short trip正常起钻 a round trip侧钻sidetracking卡钻sticking井塌cave in键槽卡钻key-seating sticking完钻finish drilling停钻stop drilling进尺make meters完井成本the cost of completion中和点neutral point of the string张力tension拉力冲数stroke钻头压力降pressure drop across the bit泵压pump pressure钻压drilling weight钻速the rate of penetration设计深度the planed depth固井设计cementing design泥浆性能试验experiment in mud property立方米cubic meter主要用途the principal purpose高粘hi-vis有粘度的viscous。
石油钻井英语词汇
对照实物确认的钻井词汇一、井口与井控1. 套管头升高短节（上下由法兰连接，中间是三通或四通）casing spool2. 油管悬挂器tubing hanger3. 油管悬挂器上边接有阀门的盖子tubing bonnet4. （可焊接的）导管头（接箍）conductor connector5. （可焊接的）套管头（接箍）casing connector6. 井口帽blanking cap & plug7. 三闸板防喷器triple slide-lok preventer8. 双闸板防喷器double slide-lok prevente9. 油/套管升高短节tubing/casing riser10. 整体式升高短节integral union riser11. 法兰×丝扣井口转换头wellhead adapter12. 井口四通两边的横向阀门wing valves13. 油管悬挂器上边的变径法兰大小头bonnet14. 上边是法兰的套管头casing flange15. 只上边是法兰，下边与表层套管焊接的套管头casing head16. 套管头内的卡瓦casing slips17. （上法兰小，下法兰大）变径套管头casing spool crossover18. 与导管焊接的坐在圆井底的套管头landing head flange top19. 卡瓦密封套管悬挂器slips seal casing hanger20. （上下是法兰，中间是四通的）油管升高短节tubing spool21. 柔性封隔闸板flexpacker ram22. 可变径闸板variable bore ram23. 剪切闸板shearing blind ram24. 卡瓦型套管悬挂器slip-type casing hangers25. 高负荷悬挂器high-load hanger26. 悬挂器断开式密封圈hanger isolation seal ring27. 井口封隔变径变压法兰（中间有几道密封圈，下边是低压，上边是高压）pack off/crossover flange28. 油管头（下法兰大，内带密封圈；中间是四通，上法兰小）tubing heads29. 底（下）变径法兰（下边内径大，上边内径小）basic adapter30. 单密封变径法兰（下内径大，上内径小）single seal bore adapter31. 变径大小头（下边是法兰，上边是本体上钻孔攻丝扣）coupling adapter32. 油管悬挂器转换大小头短节（上法兰小，下法兰大，下法兰内有丝扣）tubing suspension adapter33. 双油管悬挂器dual completion tubing hanger34. 双密封孔连接法兰dual seal bore adapter35. 锁紧螺丝lockdown screw36. （地面）单油管密封总成single packer completion37. 法兰式采油树盖子flanged tree caps38. 扰性油管悬挂器coiled tubing hanger39. 扰性油管头coiled tubing head40. 高级环形防喷器芯子supreme stripper41. 旋转防喷器rotating BOP42. 下面带有母扣的套管头casing head housing with female casing thread43. 带底盘的套管头casing head housing with base plate44. （上法兰小，下法兰大）带四通的套管头crossover casing spool45. 常规油管头conventional tubing head46. 防喷器吊装系统BOP handling system47. （装在压井管汇一边的）单流阀check valve48．标准扰性油管树总成typical coiled tubing tree assembly49. 套管悬挂器（即套管头内的卡瓦）casing hanger50. 万能防喷器芯子packing unit51. 装压力表的井口或采油树顶盖flow adapter52. （较大较厚的）密封圈packoff53. （从井口通往节流管汇的）液控阀HCR valve54. 回压阀（止回阀）check valve55. 套管头外壳CHH＝casing head housing56. 套管头上的四通CHS=casing head spool57. 用在套管头与四通之间的变径变压法兰DSA=drilling spool adaptor58. 地平面GL=ground level59. 手动阀门MV=manual valve60. 双头螺栓连接的油管头四通DSTHS=double studded tubing head spool61. 双头螺栓连接的密封转换法兰DSPOAF=double studded pack-off adaptor flange62. 大直径导管stovepipe63. 压井钻井液KWM=kill weight mud64. 井口最大允许环空压力（套压）MAASP=maximum allowable annular surface pressure65. 起钻POOH=pull out of hole66. 下钻RIH=run in hole67. 关井立管压力SIDPP=shut-in drill pipe pressure68. 关井套压SICP=shit-in casing pressure69. 副司钻AD=assistant driller70. 垂直井深TVD=true vertical depth71. 垂直方向TVD=true vertical direction72. 压井排量和压力KRP=kill rate & pressure73. 初始循环压力ICP=initial circulating pressure74. 终止循环压力FCP=final circulating pressure75. 测量深度（实际井深）MD=measured depth76. 钻井液密度MD=mud density77. 每分钟冲数SPM=strokes per minute78. 井底压力不变CBHP=constant bottom-hole pressure二、套管和固井1. （固井或压井用的高压管线）可转向短节swivel joint2. 由壬hammer lug unions3. 防硫化氢由壬（H2S）sour gas unions4. 焊接由壬butt weld unions5. 上扣由壬threaded unions6. 焊接弯头welded elbow7. （约两三米长，两三吋的）两头带由壬的高压固井、压井管线pup joint8. 水泥头plug lounching head9. （刮管器上的）刮刀片scraper blades10. 回收式水泥分割器retrievable cement packoff11. 可钻水泥分割器drillable cement packoff12. 杯形水泥分割器cup style cement packoff13. 封割器坐入工具packoff setting tool14. 带可钻封隔器的尾管挂liner setting collar with drillable packoff15. 带回压阀的引鞋PVTS16. 自动灌钻井液引鞋self-filling float shoe=fill-up valve=fillup mode17. 带分流孔的（防堵）引鞋down-jet float shoe18. 桥塞bridge plug19. 机械式桥塞（或尾管）送入工具mechanical setting tool20. 大直径限位环oversize stop ring21. 封隔器胶皮限位套packer thimble22. （螺旋刮管器上的）刀片限位套blade retainer23. 单回压阀引鞋single float set shoe24. 双回压阀引鞋dual float set shoe25. 扣闩式尾管固井胶塞承托环latch landing collar26. 旋转式尾管送入器rotating liner running tool27. 坐入器清杂网setting tool debris screen28. 套管扶正器限位套stop collar=dog collar29. 不焊接的套管扶正器non-welded centralizer30. 半钢性套管扶正器semi-rigid centralizer31. 无焊接涡流式套管扶正器non-welded turbolizer32. 钢性套管扶正器rigid centralizer33. 水泥篮cement basket34. 固体分流器solid body diverter35. (双级固井)第一级堵塞器first stage sealing plug36. (双级固井)第二级“炮弹”式旁通打开器free-ball opening device37. (双级固井)第二级堵塞器closing plug38. (双级固井)泵冲式旁通打开器pump down opening plug39. (双级固井)旁通堵塞器by-pass plug40. 分级箍stage cementing collar41. 套管快速护丝quick-clamp thread protector42. 套管双公短节casing nipple43. 引鞋float nose=guide shoe=set shoe44. 铰链式套管扶正器hinge-type centralizers45. 多级固井分级箍multiple stage cementing collar46. 单级固井水泥头single stage cementing head47. 双级固井水泥头two stage cementing head48. 有焊接弓形弹簧扶正器welded spring bow centralizer49. 无焊接直条扶正器non-weld straight bow centralizer50. 短螺旋刚性扶正器short spiral rigid centralizer51. 扶正器限位套stop collar52. 套管涨管器casing roller53. 插入杆stinger54. 插入（接）头tag-in adapter55. (插入式固井的)插入座tag-in float collar56. 插入式固井下部结构tag-in assembly57. 插入式固井用的钻杆座和卡瓦drill pipe bowl and slips58. (插入式固井)水泥头pack-off head assembly59. (插入式固井)上丝扣式的插入头screw-in adapter60. (插入式固井)锁闩式插入头screw-in adapter61. (插入式固井)插入密封头stab-in seal sub62. 螺旋清砂扶正器（套）spiral solid stand-off centralizers63. 直刮刀式清砂扶正器solid “straight blade” stand-off centralizer64. (扶正器与井壁)接触长度wall contact65. 回压阀back pressure valve66. (固井或压井用)约2～5米长，2吋或3吋高压管线longsweep hose67. 双公由壬短节male×male union ends68. 公母由壬短节male×female union ends69. 总长overall length70. 水泥头releasing bail operator71. 进扣长度make up loss=thread swallow三、管材与配件1. 四通full flow cross2. (等边)三通long sweep full flow tee3. 90度弯头long sweep 90° ell4. 侧三通long sweep tee5. 顶部有出口的160度立管鹅颈管三通standpipe gooseneck 160° with top outlet6. 45度弯头long sweep 45° ell7. 大小头adapter sub8. 循环三通T-pump-in sub9. 变径大小头（粗细扣大小头）crossover adapter10. 短钻杆drill pipe pup joint11. 十字四通连接管cross connector12. 丁字三通连接管tee connector13. 活动转向短节（固井、压井管线）Chiksan swivel joint14. 伸缩短节expansion joint15. 细扣管线堵头bull plug16. 细扣管线大小头line pipe swages17. （两半式带手柄的）水管线卡子hinglelok18. （两半式用两个螺栓固定的）水管线卡子rigidlite coupling19. 细扣管线接箍（双母）line pipe coupling=steel merchant coupling20. 丝扣连接旁通（出口）threaded side outlet21. 螺栓连通旁通studded side outlet22. 母扣female threaded23. 盲板法兰blind flange24. 内径带丝扣的法兰companion flange25. 内径带密封圈的法兰packoff flange26. 变径法兰crossover flange27. 与法兰连接的方块四通studded cross28. 与法兰连接的方块三通studded tee29．与法兰连接的丝扣三通flanged by thread tee30. 单头可转短节（仅一头能转动的短节）single swivel coupling31. 单弯脖单头可转短节single swivel with one elbow32. 双弯脖单头可转短节single swivel with two elbows33. 双弯脖双头可转短节two swivels with two elbows34. 单弯脖双头可转短节two swivels with one elbow35. 三弯脖双转向短节two swivels with three elbows36. 三弯脖三转向短节three swivels with three elbows37. 双弯脖三转向短节three swivels with two elbows38. 方（块）铁直角弯脖block connector39. 90度弯脖long radius connector40. 可变径弯接头knuckle joint41. 管线滤清器strainer四、地面与井下工具A. 地面工具1. 砂轮片grinding wheels2. 手动钻具台肩修整器shoulder facing device3. 内六楞凹头螺栓allen head cap screws4. 六楞弯头扳手allen wrench5. 带限位台肩的接头stop sub6. 固定螺丝（限位螺丝）retainer screw7. 方瓦驱动方钻杆square drive8. 销子驱动方钻杆（滚子方补心带四个爪）pin drive9. 高强度滚子方补心heavy duty roller Kelly bushing10. 钻杆卡瓦rotary slips11. 钻铤卡瓦drill collar slips12. 导管卡瓦conductor pipe slips13. 套管卡瓦casing slips14. 铰链式套管卡瓦hinged casing spider15. 气动套管吊卡/卡瓦casing elevator/spider16. 安全卡瓦clamp17. 滚筒排绳槽lebus groove18. 装在井架大腿上的死绳固定器mast leg mount anchor19. 死绳固定器wireline anchor＝deadline anchor20. 绷绳地锚deadman21. 离合器clutches22. 刹车片brakes23. 端面离合器刹车片disc brakes24. 快速放气阀quick release valves25. 转子密封器rotorseals26. （大直径管线）充气密封圈air-o-union27. （保险）放压阀pressure relief valve28. 钻井液防喷盒mud miser29. 鼠洞上扣钳和吊卡mousehole spinning wrench & elevator30. 销子驱动方补心pin drive Kelly bushing31. 方铁驱动方补心square drive Kelly bushing32. 高压胶管diver hose33. 滚筒刹带brake bands34. 刮泥器pipe wipers35. 高强度链钳heavy-duty chain36. 泵缸套imperial liner37. 中间带钢圈的活塞imperial piston38. 耐用活塞（中间无钢圈）extra-life bonded piston39. 中间有扶正器（孔）的阀体和阀座imperial valves and seats40. 带四个爪的阀体和阀座roughneck full open series valves and seats41. 刹带片brake blocks42. 泵空气包胶囊diaphragms for pulsation dampener43. 方钻杆下旋塞Kelly guard44. 小鼠洞上扣器rotating mousehole45. （钻台上用的）气葫芦air tugger46. 分体式游车大钩trunion supported hook47. 连体式游车大钩adapter supported hook48. 喷射式混合漏斗jet mixing system49. 单作用泵活塞single acting pump piston50. 双作用活塞泵double acting pump piston51. 手动油管卡瓦manual tubing spider52. 气动油管卡瓦air powered tubing spider53. 气动卡瓦slip spider54. 气动吊卡slip elevator55. 长体手动卡瓦extra long slips56. 多片式钻铤卡瓦multisegment drill collar slips57. 链钳chain tong58. （大管线）充气密封圈air-inflatable tight seal59. 快扣加固井架用保险带snap-on cable reinforced derrick belt60. 高台罐区用保险带platform and tank belt61. 放线工保险带lineman’s belt62. 快扣弯连接二层台和井架保险带（宽腰有背带）snap-on and buckle-on combination monkey board and derrick belt63. （宽腰无背带）加固二层台保险带reinforced monkey board belt64. 弯接加固二层台保险带buckle-on cable reinforced derrick belt65. 高强度蛇皮接绳器heavy-duty grips66. 单股或双股编织接绳器single or double weave grip67. 三股编织接绳器triple weave grips68. 四股编织接绳器quad weave grips69. 单（双）接环蛇皮接绳器single (dual) eye grip70. 顶部开口单接环蛇皮接绳器single eye top opening grip71. 顶部开多口单环蛇皮接绳器topside multiple opening grip72. 接绳转向器directional boring swivels73. 指重表weight indicator74．压力表pressure gauge75. 电子转盘扭距表electric rotary torque76. 大钳扭距tong torque77. 泵冲数表SPM pump speed indicator78. 自动送钻automatic driller79. 二层台钻杆支梁finger board80. 刹车鼓brake rims81. 钻杆刮泥器(drillpipe) stripper rubber82. 接链器chain connector83. （大绳）排绳器wireline guide84．单头内六方扳手impact box end wrench85. 六楞方钻杆hexagonal Kelly86. （装在滚筒护罩上的）防碰天车阀short toggle valve87. 拧扣器make-up/break-out unitsB. 井下工具1. 铆钉式可调螺旋扶正器undergauge adjustable stabilizer2. 钻头导向器bit pilot3. 整体式螺旋扶正器integral blade stabilizer4. 焊接式螺旋扶正器welded blade stabilizer5. 可变径扶正器variable gauge stabilizer6. 可更换的扶正器套stabilizer sleeves7. 换套扶正器心轴stabilizer mandrel8. 滚子扶正器roller reamer9. 单级牙轮扩大器（下边可接领眼钻头）single stage hole opener10. 六方减震器hex bumper sub11. 牙轮取心钻头roller core-barrel head12. 刮刀取心钻头blade core-barrel head13. 钻铤螺旋槽spiral groove14. 方钻铤square drill collar15. 光钻铤slick drill collar16. （钮扣式）碳化钨扶正器套sleeve with tungsten carbide buttons17. 镍合金扶正器套sleeve with nivalloy18. 滚子扶正器rotary reamers19. （密封轴承）井眼扩大器sealed bearing hole openers20. 钻头喷嘴jet nozzle21. 无卡簧槽的喷嘴standard nozzle22. 有卡簧槽的喷嘴shrouded nozzle23. 磨鞋式螺旋扶正器watermelon mill24. 磨鞋式短螺旋扶正器string mill25. 螺旋加重钻杆spiral-wate drillpipe26. 扩大器U/R=underreamer五、钻井液药品与缩写符号1. 稀释剂（液体，约25kg1桶）2. 抗高温流变性稳定剂3. 抗高温流变性稳定剂，属稀释剂，加重时用一点，不增稠，液体约200kg1桶4. 液体，润滑剂，约200kg1桶5. 高温高压失水稳定剂（降失水），干粉，约25kg1袋6. （有时只写作XCD或CD），生物聚合物，降失水，调流变性，提粘（钻井液稀—流变性低）7. 干粉堵漏剂（类似国内的随钻堵漏剂），成分：锯末、稻糠、植物种子8. 中号碎核桃壳（相当于麦粒大小）9. 细云母粉云母片10. 蚌壳渣11．（有时只写作PAC），干粉，相当于国内的CMC，有时在Drispac后加上R或SL，其意是：R—regular 高粘，SL－superlow 低粘，中文名：聚阴离子纤维素12．滤液酚酞碱度13．钻井液酚酞酸度14. 滤液甲基橙碱度15. 亚甲基蓝测定法（膨润土含量）16. 钻井液密度17. 每加仑磅18. 粘度19. 塑性粘度20. 秒21. 夸脱22. 厘米/秒23. 屈服点（流动点）24. 磅25. 英尺26. 静切力（胶凝强度）27. （氢离子浓度倒数的对数）28. 立方厘米立方容积29. 美国石油学会精确位置显示器30. 桶31. 钙32. 百万分率（百万分之几）33. 钻屑34. 磅/桶35. 尽可能低36. 失水37. 高温高压38. 聚阴离子纤维素衍生物六、打捞工具1. 平底牙轮磨鞋2. 带锯齿的铣鞋3. 铣锥4. 枣核形铣锥（两头带丝扣）5. 打捞颈6. 篮式卡瓦7. 螺旋弹簧式卡瓦8. 螺旋弹簧式卡瓦控制环9. 篮式带铣鞋卡瓦控制环10. 母铣锥11. 大头壁挂式坡口打捞引鞋12. 厚壁管制的壁钩13. 卡瓦打捞筒加长管14. 母锥15. 带坡口引子的母锥16. 打捞矛上的退出环17. 笔尖式引子18. （打捞筒内的）落物打捞爪19. 锯齿底引子20. 壁钩式坡口引子21. 四楞短锥体带喷嘴磨鞋22. 锥头引子23. 爪式引鞋24. 锯齿式引鞋25. 随钻打捞杯26. 刮刀式磨鞋27.28.。
钻井专业词汇
MWDdirectional well 定向井horizontal well 水平井cluster well 丛式井deviation well 定向斜井multiple well 多底井relief well 救援井coordinates 坐标X-, Y- , Z- coordinates X，Y，Z坐标displacement 位移declination 磁偏角hole inclination or hole angle 井斜角maximum hole angle 最大井斜角hole direction 方位角end of deviation 最终井斜azimuth 方位，方位角Geographic North (meridian direction) 地理北，真北Magnetic North (compass direction) 磁北Magnetic Azimuth (MA) 磁方位displacement or closure distance 水平位移horizontal displacement 水平位移vertical section 垂直面vertical, horizontal projection 垂直, 水平投影rate of build up 造斜率dogleg 狗腿DLS (Dogleg Severity) 狗腿严重度，井眼曲率KOP kick off point 造斜点target 靶，目标点vertical depth of target 目标垂深target radius 靶区半径actual hole shape 实际井眼形状MWD tool 随钻测斜工具ESS (Electronic Survey System) 电子测斜仪 tool face 工具面tool face angle 工具面角tool face setting 工具面安置角varidril 涡轮钻具，螺杆bent sub 弯接头NMDC (non-magnetic drill collar) 无磁钻铤 stabilizer 稳定器centralizer 扶正器drilling jar 随钻震击器SWDmeasured depth 测量深度TVD True Vertical Depth 真实垂直深度mean sea level 平均海平面seismic datum 地震资料 checkshot table (地震声波测井)校验炮列表full waveform display 全波形显示seismic energy signal 地震能量信号reflect wavefield 反射波场direct arrivals 直达波reflected arrivals 反射波interval velocity , average velocity 区间速度，平均速度replacement velocity 置换速度drillstring velocity 钻杆传输速度RMS (resistivity of mud sample) velocity泥浆样品电阻率速度travel times 传输时间interval transit time 区间传输时间vertical section 垂直段plane of vertical section 垂直剖面offset, 偏移，炮检距departure 离差latitude 纵距azimuth 方位，方位角5 . SHEET & REPORT工单，报表与报告5.1 SHEET & TALLY报表与记录job notes 工作单tripping sheet 起下钻工作单reason for the trip 起下钻原因displacement 替泥浆量，灌泥浆量pull on: even , single , double 起钻钻柱：整立柱，单根，双根stand No. 立柱号trip tank gauge 起下钻罐计量值calculated hole filling per increment 每一个变量计算的井眼灌浆量measured hole fill 测量的井眼灌注量discrepancy 误差，差异well control pre-kick sheet 予压井工作单measured depth 测量井深measured casing shoe depth 测量的套管鞋深度TVD true vertical depth 真实垂直深度casing shoe TVD 套管鞋处垂直深度capacities and volumes 容积与体积 drill string data 钻具数据annulus data 环空数据total system volume 总的系统体积 bit to shoe volume (strokes, time) 钻头到套管的体积（所需泵冲，时间）surface to bit strokes (time) 地表到钻头循环所需泵冲（时间）S.C.R slow circulation rate 低泵速循环速率read and record 读值与记录well control kick sheet 压井工作单 pit gain 罐增益量formation breakdown gradient 地层破裂梯度maximum mud weight 最大泥浆密度M.A.A.S.P maximum allowable annulus surfacepressure最大允许环空地表压力I C P initial circulating pressure 初始循环压力F C P final circulating pressure 最终循环压力pressure step-down 压力减小total strokes to kill well 压井所需总泵冲total time to kill well 压井所需总时间M.A.C.P maximum allowable casing pressure 最大允许套管压力drilling information sheet 钻进信息工作单pump and mud information 泥浆泵与钻井液信息string and hole information 钻具与井眼信息up ,down , on bottom off bottom 上提，下放，接触井底，提离井底BHA bottom hole assembly 下部井眼钻具组合BHA No. 下部井眼钻具组合编号BHA types 下部井眼钻具组合类型item , serial No. , length 项目名称，系列编号，长度OD outside diameter 外径ID inside diameter 内径FOND 打捞外径FNL 币打捞内径weight below jar 震击器以下重量 total BHA weight 下部钻具组合总重量bouyed weight total 总的浮力重量 N / A next assembly 下次装配not applicable 不适用的not available 无效，未利用NA non-available 无资料，不详，不合用varidril 动力钻具bent housig 弯接头orienting sub 定向接头pulse sub 脉冲接头DC drill collar 钻铤pony DC 短钻铤NMDC non-magnetic drill collar 无磁钻铤HWDP heavy weight drillpipe 加重钻杆DP drillpipe tally 钻杆记录表joint length 单根长度stand No 立柱号stand length 立柱长度sum length 总长度casing tally 套管记录表joint length 单根长度sum length 总长make-up length 组合长度casing length 套管钢级tubing tally 油管记录表corrective length 校正长度thread length 丝扣长度sample list 岩样清单item 项目unwashed sample 未洗样dry sample 干样canned sample 罐装样box No. 箱号interval 井深间隔notes, remarks 注释，标记consumable price list 消耗物品价格表item description 项目名称unit price 单价comment 说明material consumption list 材料消耗清单item 项目quantity 数量，用量5.2 REPORTS AND LOGS 报告与录井图表dairy charge report 日费结算报告 mud logging during 作业时间起止 signature 签名CO. REP.report 公司代表报告 midnight depth 午夜钻进井深 previous depth 以前的井深gas reading 气体读值background gas 背景气pipe connection gas 接单根气peak 显示高峰TOT HHP 总的水马力损失BIT HHP 钻头水马力损失geological morning report 地质早报 present operation 现在作业情况 lithological summary 岩性小结24 hrs operations summary 24小时作业情况摘要24 hrs forecast 未来24小时作业预测Well site core description report 井场岩心描述报告End of Well Report 完井报告final well report 完井报告final mud logging report 泥浆录井完井报告contents 目录introduction 前言well data 井史数据资料mud logging description 泥浆录井工作描述stratigraphy 区域地层hydrocarbon shows summary 烃类显示摘要pressures discussion 压力讨论summary of drilling events 钻井事件摘要appendix 附录The format end of well report by Halliburton 哈里伯顿公司完井报告格式contents 目录overview(=well data) 概述（相当于数据大表）well profile 井身剖面图1, Mud logging service provision 泥浆录井设备rig layout and location of sensors 钻机设备平面图及传感器位置sensor specifications 传感器技术规格2, Geology 地质lithological discussion 岩性探讨 sampling and dispatch 岩样与岩样清单3, Overpressure 超压，过压overpressure discussion 地层超压讨论overpressure plots 超压绘图4, Drilling 钻井hole section summaries 各井段概述bit data 钻头数据BHA configurations BHA配置 mud summary 钻井液概述bit run hydraulics 钻头水力学 5, Deviation 井斜deviation summary 井斜概述survey data and plot 井斜数据及井斜图6, Petrophysical analysis 岩石物理学分析gas data summary 气体数据概述gas ratio crossplot 气体比率交汇图7, Time breakdown 作业时效分析well progress plot 钻井进度图 rig time analysis 钻机作业时效分析统计8, Inclusions 内附，包含lithology log MD 1:500 1：500测深岩性录井图lithology log TVD 1:500 1：500垂深岩性录井图drilling log 1:500 1：500工程录井图normalised gas log 1:500 1：500校正的气体录井图pressure log 1:2000 1：2000压力录井图drilling data ASCII data diskette ASCII 码钻井数据软盘master log 主录井图lygend 图例company 公司名称rig 钻井队名称area 所在地区country 所在国家location 位置elevation 海拔高度water depth 水深depth ref 井深参考RKB rotary kelly bushing 方钻杆补心高度well configuration 井身结构bit size 钻头尺寸hole depth 井眼深度casing size 套管尺寸shoe depth 套管鞋深度spud date 开钻日期TD date 钻至总井深日期TD driller 总井深logged from 录井开始日期logged to 录井作业止depth scale 井深比例pressure evaluations log 压力评价录井图TGN log (total gas normalized) TGN录井图cutting sample log 岩屑录井图 core sample log 岩心录井图core sample examination sheet 岩心样品检验结果单gas analysis chart 气体分析图表 shale density measurements 页岩密度测量表5.3 SOME USEFUL ABBREVIATIONS 一些有用的缩略语NB new bit 新钻头NCB new core bit 新取心钻头RRB re-round bit 再次入井钻头 BR bit run 钻头进尺WOB weight on bit 钻压SPP standpipe pressure 立压PP pump pressure 泵压RPM revolutions per minute 转盘转速 SPM strokes per minute 泵冲CS casing shoe 套管鞋位置CR circulated returns 循环返出物 CG connection gas 接单根气TG trip gas 起下钻气WTG wiper trip gas 通井后效气 NR no returns 无返出物PR poor returns 返出物较少EL electric log 电测POOH pull out of hole 起钻RIH run in hole 下钻WT wiper trip 通井LAT logged after trip 起钻后测井 DS directional survey 定向测斜DST drill stem test 钻杆中途测试 DC depth correction 井深校正RMG reaming 划眼WOW wait on weather 等天气WOC wait of cement 固井水泥候凝 WOO wait on order 等指令，待命 LAT logging after trip 起钻后测井 LCM lost circulation material 堵漏剂，堵漏材料FR flow rate 流速FC flow check 溢流检查abbreviations of mud data 泥浆数据缩略语W weight lb / gal 比重，密度MG mud gradient psi / kft 泥浆梯度 V funnel viscosity s /qt 漏斗粘度AV apparent viscosity 表观粘度PV plastic viscosity cp 塑性粘度YP yield point lb / cf2 屈服点，动切力GEL gel strength lb / cf2 静切力PH acidity 酸度moisture 湿度F filtrate cm3 /30 泥浆滤液FL filtrate loss 滤失量CK cake thickness in / 32 泥饼厚度S salinity kg /m3 泥浆矿化度SD sand content % 含砂量O oil content 含油量WL water lose cm 3 / 30 失水SOL solids content % 固相含量PF filtrate alkalinity % 碱度，含碱量GYP gypsum content lb / bbl 石膏含量Additives for drilling fluid 钻井液添加剂releasing stuck agent 解卡剂LCM lost circulate additives / plugging agent 堵漏剂foaming agent, foamer 发泡剂flocculant, flocculating agent 絮凝剂bactericidal agent, biocide 杀菌剂defoaming agent, defoamer 消泡剂emulsifier, emulsifying agent 乳化剂bridge agent 桥堵剂retarder, retardant 缓蚀剂lubricant 润滑剂viscosifier, thickener 增粘剂viscosity-reducing agent, thinner 降粘剂5.4 COMMENT & REMARKS 注释与标记note, comment, 注释，标记remarks 注释，说明All the drilling troubles 、accidents and some main changed parameters should benoted on the logs and real-time charts.所有钻井复杂情况、事故及一些主要的变化的参数均应标注在录井图件和实时打印资料上Run bit No. 4 下入第四号钻头bit parameters, 钻头参数bit manufacture 钻头制造商bottom up / lag time 迟到时间Pump off for 停泵…分钟PC pipe connection 接单根connection gas 接单根气trip gas 起下钻气carbide test 电石气试验carbide gas 电石气change ROP scale 变换ROP比例 setting zero 调零，置零gas system re-calibrated 气体系统重新标定midnight depth 午夜井深case steel grade 套管钢级casing shoe 套管鞋位置liner 尾管下深slurry density 水泥浆密度cement quantity 水泥用量cement plug 水泥塞厚度leak off test 地层漏失试验starting drilling 开始钻进drill with fresh water 用清水钻进 drill with sea water 用海水钻进POOH to core at 3215m 起钻在3215米取心coring interval 取心井段core length 岩心长度core recovery 取心收获率dumping returns 返出物放掉no gas data 无气体数据NS no survey 未测，没有测n.s no sample 无样品no sample collected 无岩样high total gas due to diesel contamination 总烃显示高值是由于柴油污染所致gas show 气体显示gas peak 气显示高峰值well kick 井涌flow check 溢流检查choke circulating 节流循环raised mud weight 提高泥浆密度 short trip 短起下钻change BHA 换下部钻具组合 overpull 超拉bit lost in hole 钻头落井，掉钻头broken pipe 断钻具fishing 打捞fish top 鱼顶fish length 鱼长fishing cutter 打捞切割器MU( make up) new BHA 组合新BHAtest MWD tool 测试MWD工具 install top drive 安装顶驱cut and slip 倒大绳PU (pick up) 15 joints 配接15根单根raise MW( mud weight) to 18.2ppg 提泥浆密度至18.2ppgreduce mud weight 降泥浆密度check losses or gain 检查泥浆漏失，增益shut in well 关井observed pressures 观察压力squeeze LCM (lost circulated additives) 挤堵漏剂pump spacer fluid 打隔离液displace packer fluid 替封隔液drill break 钻进放空circulate bottom up 将井底泥浆循环出来back reaming / pumping back 倒划眼 pump out of hole to shoe 倒划眼至套管鞋。
钻井术语词汇
这里有你要的几乎钻井专业的所有专业词汇，包含你要的钻井四通：drill spool 1.accumulator储能器2.active tank循环池3.adjusting bolt(刹把)调节螺栓4.admission pipe进气管5.agitator搅拌器6.air chamber空气包7.air line气管线8.air-operated hoist气动绞车9.alternating current drive交流电驱动10.annular BOP环形BOP11.ato-muffler消音器12.ball valve球阀13.bell nipple老虎钳14.bench vise钻头15.bit钻头16.Bit gauge钻头装卸器17.bit gauge钻头规18. blind ram preventer盲板防喷器19. blind shear ram preventer剪切闸板防喷器20.blow-out preventer（BOP）防喷器21.bolt22.BOP control panel防喷器控制盘23.BOP deck防喷器平台24.bottom plug底塞25.box母扣26.brake level(brake handle) 刹把27.brake line(brake staple) 刹带28.bridge plug桥塞29.buttress梯形扣30.butterfly valve蝶阀31.by-pass旁通32.by-pass plug旁通塞33.callipers卡钳34.casing bowl套管打捞筒35.casing coupling套管接箍36.casing cutter套管割刀37.casing elevator套管吊卡38.casing hanger套管悬挂器39.casing head套管头40.casing monkey board套管平台41..casing scraper刮管器42.casing shoe43.casing slip套管卡瓦44.casing spear套管打捞矛45.casing spool套管四通46.casing tong套管大钳47.cat line锚头绳48.cat line grip锚头绳爪49.cat shaft锚头轴50.cat-head锚头51.cellar deck井口甲板52.cement水泥53.cement basket水泥伞54.cement plug水泥塞55.cement retainer水泥阻流环56.cementing bond log 固井质量检查57.cementing head水泥头58.cementing line固井管线59.cementing pump固井泵60.chain链61.chain pipe tong链钳62.chain tong链钳63.chamber64.chamber gate阀箱,闸室65.charge pump灌注泵66.check valve止回阀,回压凡尔67.choke节流器,阻流器68.choke line阻流管线69.choke position indicator 节流阀位置指示器70.choke valve节流阀71.choke -line manifold阻流管汇72.clutch离合器73.conductor导管74.cone牙轮75.cone fisher牙轮打捞器76.cone lock牙轮卡死77.cooling-water pump冷却水泵78.core barrel shoe取心筒鞋79.core basket取心爪80.core bit取心钻头81.core catcher岩心爪82.∞re catcher case岩心爪外套83.core drying oven岩心烘箱84.crossover joint(x/o)85.crown block天车86.crown block beam天车梁87.dead line死绳88.dead line diaphragm死绳固定器膜片89.dead line anchor死绳固定器90.degasser除气器91.derrick井架92.desander(desilter)除砂(泥)器93.direct current drive直流电驱动94.discharge line排出管线95.discharge valve排出阀96.double ram type preventer 双闸板防喷器97.down hole tool人井工具98.draw works绞车99.drawworks motor绞车电机100.drift mandrel通径规101.drill collar钻链102.drill collar slip钻链卡瓦103.drill pipe钻杆104.drill pipe slip钻杆卡瓦105.drill pipe wiper106.ddll string钻柱107.driller'sb console司钻控制台108.drilier's monitor司钻监视器109.drilling line(workline) 钻井大绳110.driiling stem valve钻杆防喷器111.drive shaft驱动轴112.driven shaft从动轴113.driving chain传动链条114.drum滚筒115.drum capacity滚筒容量116.drum clutch滚筒离合器117.drum hight air clutch 滚筒高速（低速）118.drumlow air clutch空气离合器119.DV collar分级箍120.eddy current brake涡磁刹车121.elevator吊卡122. elevator link吊卡耳环123.elevator-spider吊卡-卡瓦124.emergency jaw clutch 应急牙嵌离合器125.equalizing yoke(刹带的)平衡杠126.external cutter127.external cutter外部割刀128.eye plate吊耳，吊环129.eye splice绳套,接环130.fill up iine灌泥浆管线131.fiitration test apparatus 失水测定仪132.finger board指梁133.fishing hook打捞钩134.fishing head打捞头135.fishing jars打捞振击器136.fishing neck打捞颈137.fishing nipple打捞公锥138.fishing operation打捞操作(作业)139.fishingmcitet打捞母锥140.fishing spear打捞矛141.fishing string打捞管柱142.fishing tap(taper)打捞公锥143.fishing tool打捞工具144.flange法兰145.flat(round,square)file 扁(圆,方)锉146.flat bit tongs扁嘴钳(电工用)147.flat bottom mill148.flexible joint挠性接头149.float shoe浮鞋150.float valve浮阀151.floating collar浮箍152.four →way valve四通阀153.free point indicator卡点测定仪154.full hole joint贯眼钻杆接头155.funnel viscometer漏斗粘度计156.gas holder(tank)储气筒,储气罐157.gate大门158.gate valve闸门阀159.g∞se neck p ipe鹅颈管160.hammer锤子161.heavey weight drill pipe加重钻杆162.heaηr wall drill pipe厚壁钻杆163.high pressure line高压管线164.hole opener开眼器,扩眼器165.hook大钩166.hook spring大钩弹簧167.hose水龙带168.hydraulic break-out cylinder169.hydraulic catwork液压猫头170.hydraulic pump液压泵171.hydraulic reservoir-液压油箱172.hydraulic tong液压大钳173.hydraulic valve咒液动阀174.hydraulic (press) test pump 液动试压泵175.hydraulic-powered winch 液压绞车176.inertia惯性177.inertia brake惯性刹车178.inlet人口179.inner core barrel内岩心筒180.intermediate casing中间(技术)套管181.internal blowout preventer 钻柱内防喷器182.internal callipers内卡钳183.internal external upset内外加厚184.internal flush joint内平钻杆接头185.jar振击器186.jaw clutch牙嵌离合器187.joint接头,(钻杆)单根188.junk basket笼式打捞篮189.junk catcher打捞爪,一把抓190.junk sub打捞杯191.kelly bushing方补心192.kelly cock方钻杆考克193.kelly protective sub 方保接头194.kdly spinner方钻杆旋转短节195.key seat reamer键槽破坏器196.killline压井管线197.knee pipe弯管dder梯子199.level水平仪(尺)200.lifting plug提升丝堵201.lifting sub提升短节202.line reeving滑车装绳数203.liner缸套204.liner尾管205.lock bolt锁紧螺栓206.locking flange锁紧法兰207.low pressure line低压管线208.lube oil pump润滑油泵209.lubrication hole加油孔210.magnetic fishing tool磁力打捞工具211.make out cathead 卸扣猫头212.make up cathead 上扣猫头213.manual drill手摇钻214.manual valve手动阀215.master bushing 转盘大补心ling shoe镜鞋ling tool锐具218.mixing hopper混合漏斗219.mixing pump混合泵220.monkey hard猴台221.motor电机,马达222.mouse hole小鼠洞223.mud balance泥浆比重计224.mud cleaner泥浆清洁器225.mud ditch泥浆槽226.mud guard挡泥板227.mud gun泥浆枪228.mud pump泥浆泵229.mud relief valve 泥浆泵安全阀230.mud return line泥浆返出管线231.mut pit232.nail钉子233.near-bit stabilizer近钻头扶正器234.needle valve针形阀235.nigger-head扳手加长套筒236.nipper慑子,夹子237.non-magnetic drilling collar 非磁钻键238.normal close valve常闭阀239.normal open valve常开阀240.nozzle水眼,喷嘴241.nut螺帽242.nut bolt带帽螺栓243.nut spinner自动螺母扳手244.oil level油位245.oil level check plug油位检查丝堵246.oil tank油柜247.oil-level dipstick油尺248.open -ended spanner开口扳手249.outer core barrel外岩心筒250.outlet出口251.paint brush油漆刷252.pilot bit253.pin公扣254.pin销子255.pincers钳子,夹子256.pinch bar撬棍257.piston活塞258.piston cup活塞皮碗259.piston rod活塞杆260.pliers手钳子261.plug valve旋塞阀262.pneumatic t∞l气动工具263.Portland cement硅酸盐水泥264.power slip动力卡瓦265.power supply unit动力供应设备266.power tong动力大钳267.power wrench动力扳手268.pressure snubbing tank 缓冲罐269.production casing生产层套管270.pulley滑轮271.pump-out reversing sub 反循环接头272.pup pipe joint短钻杆273.quick connection274.ramp(井架大门处)坡板275.rat hole大鼠洞276.regular tool joint正规钻杆接头277.regulator valve调节阀278.relief line放压管线279.retaining ring (support ring)承托环280.reverse circulating valve反循环阀281.reverse circulation junk basket 反循环打捞篮282.reverse circulation port反循环孔283.reverse gear倒档齿轮284.reversing tool倒扣(打捞)工具285.ring gasket钢圈286.ring spanner梅花扳手287.rivet佛钉288.rotary table转盘289.rotary table motor转盘电机290.rotary table motor blower转盘风机291.safety clamp(slips)安全卡瓦292.safety joint安全接头293.safety stop安全限位挡块294.safety switch295.safety-strap(belt)安全带296.sand reel捞砂滚筒297.screen cloth筛布298.screw螺钉299.screw driver螺丝刀300.seamless pipe无缝钢管301.setback立根盒302.setback capacity立根盒容量303.settling pit沉砂池304.shaft轴305.shale shaker振动筛306.shock absorber减震器307.side doo elevator倒开门吊卡308.single joint elevator单根吊卡309.single ram type preventer 单闸板防喷器310.slide rule计算尺311.slide tongs管钳312.sling吊索313.slip卡瓦314.slip bushing卡瓦补心315.slip bushing316.slip dog卡瓦牙板317.slip groove卡瓦槽318.slip insert卡瓦牙319.slip insert卡瓦打捞筒320.slipgxket bowl (卡瓦)锥形座321.socket套筒扳手322.spider卡盘323.spiral drill collar螺旋钻链324.spud spear钢丝绳打捞钩325.spudding bit开眼钻头326.stab -in cementing 插入式注水泥327.subbing hard对扣台(下套管用) 328.stabilizer扶正器329.stainless steel不锈钢330.stand pipe立管331.stinger插入头332.stinger strings (内管)注水泥管柱333.stud双端螺栓334.stud bolt双头螺栓335.stuffing box盘根盒336.sub接头337.suction line吸入管线338.suction valve吸人阀339.surface casing表层套管340.swivel水龙头341.tape measure卷尺342.tee三通343.thrmd丝扣344.thread dope丝扣油345.thread protector护丝346.three-cone bit三压轮钻头347.tong大钳348.tong bucket大钳平衡器349.tong dies大钳牙板350.tong head钳头351.tong mark大钳刻痕352.tong space大钳搭绞部位353.tool joint工具接头354.tool steel工具钢355.top(bottom)plug顶(底)塞356.top of the cement水泥面357.TOTCO ring baffle plateTOTCO承托环358.traveling block游动滑车359.tdp-tank泥浆计量罐360.two way valve两通阀361.v-door井架大门362.valve阀门363.valve阀,凡尔364.valve body凡尔体365.valve bonnet阀盖,阀帽366.valve cup(seat)凡尔座367.valve face阀面368.valve lever阀杆369.valve seal阀密封370.valve seat grab起阅座器371.valve spring阀弹簧372.vernier灵敏指针373.vice(=vise)虎钳374.wall hook壁钩375.wash pipe冲管376.wear bushing耐磨补心377.well-head equipment 井口装置378.whip stock造斜器,斜向器379.wing stabilizer翼状扶正器（二）．钻井作业有关词语1.type "L" connector 20"L" 型接头2.ahead water先行水3.annular velocity环空流速4.apparent viscosity表观粘度5.back off倒扣,卸扣6.back pressure回压7.back up attachment打好背钳8.ball up泥包9.ballast water压舱水10.behind water尾水11.bingham model宾汉模型12.bit cost钻头成本13.bit diameter钻头直径14.bit footage钻头进尺15.bit IADC code钻头IADC编码16.bit lift钻头寿命17.bit position钻头位置18.bit series number钻头系列号19.bit teeth钻头齿20.bit time钻头时间21.bit type钻头类型22.bit wear钻头磨损23.blow job吹扫作业24.blow line扫线用管线25.blowing pressure吹压压力26.blowout井喷27.blowout control防喷28.blowout control equipment 防喷设备29.BOP handling装卸防喷器30.bottom fill沉砂31.bottom-hole pressure井底压力32.box-box∞nnedior1双母接头33.casing program套管程序34.casing size套管尺寸35.cationic surface active agent 阳离子表面活性剂36.caustic soda烧碱37.cement bond水泥胶结38.cement channeling水泥窜槽39.cement failure固井失败40.cement flush水泥冲洗41.cement slurry水泥浆42.cementing formulation固井配方43.circulation循环44.clay base mud粘土泥浆45.control drilling控制钻进46.coring sample岩心取样47.corrosion腐蚀48.critical velocity临界速度49.crown block protector天车防碰装置50.crown block saver天车防碰装置51.cut off drilling line割大绳52.danderous objects危险品53. degasser efficiency除气器效率54.detergent除垢剂,清洁剂55.deviation survey井斜测量56.differential pressure sticking 压差卡钻57.directional drilling定向钻井58.directional well定向井59.dog leg狗腿60.dog leg ratio狗腿率61.down time停工时间62.drifting通径63.drilling assembly钻具组合64.drilling break钻进突变65.drilling contractor钻井承包商66.drilling cost钻井成本67.drilling hours钻进时间68.drilling operation钻井作业69.drilling program钻井程序70.drilling report钻井报表71.drilling daily report钻井日报72.drilling water钻井水73.dull bit grading钝钻头分级74.dyna-drill戴纳钻具75.emulsifying agent乳化剂76.erode out刺坏77.evaluation well评估井78.exploratory well初探井79.fatigue limit疲劳极限80.fill-up float shoe自动灌浆浮鞋81.filter cake泥饼82.filtration-reducing agent 降失水剂83.flocculation絮凝作用84.flowing pressure流压85.fluid loss失水86.formation地层87.formation test地层测试88.formation water地层水89.fresh water淡水,清水90.function test功能试验91.gas content气含量92.gas cut气侵93.gas in mud泥浆中的气94.gas reservoir气层95.gas showing气显示96.hard formation硬地层97.hole sin井眼尺寸98.hole straightening井眼纠斜99.hook load大钩负荷100.hook position大钩位置101.initial gel-strength初切力102.inner string cementing 内管注水泥103.interface level indicator 表面活性剂104.kelly down方人105.kelly down depth方人深度106.kelly in方人107.kelly up方余108.key-gating sticking键槽卡钻109.kick井涌110.kick control控制井涌111.killwell压井y down the drill pipe甩钻杆113.leak –off test漏失试验114.left-hand J-slot左旋"J"型槽115.log time迟到时间116.low solid mud低固相泥浆117.maximum pressure最小速度118.maximum speed最大速度119.mean sea level平均海平面120.meantide level平均潮面121.mud additive泥浆添加剂122.mud column泥浆柱123.mud conditioning调节泥浆124.mud conditioning materials 泥浆处理材料125.mud line泥线126.mud logging泥浆录井127.mud volume泥浆量128.no leak不漏129.no return无返出130.nozzle efficiency水眼效率131.nozzle size水眼尺寸132.off –bottom离开井底133.offshore海上134.oil leak漏油135.oil reservoir pressure油层压力136.oil resistant gom耐油橡胶137.oil seal油封138.oil shale油页岩139.oil-base mud油基泥浆140.on bottom接触井底141.open hole裸眼142.operator作业者143.overpull上提,遇卡144.overtonging上扣过紧145.pendulum bottom hole assembly 钟摆钻具组合146.penetration rate机械钻速147.plastic viscosity塑性粘度(PV)148.plastics塑料149.plugging back水泥回堵150.pressure loss in pipe 管内压降151.pressure test压力试验152.pump down plug泵入水泥塞153.pump efficiency泵效154.pump pressure泵压155.pump speed泵速156.pump stroke泵冲157.rated now额定流量158.reaming划眼159.record记录160.recording paper记录纸161.releasing spear松开捞矛162.retarder缓凝剂163.reverse circulation 反循环164.rig floor钻台165.rotary speed转盘转速166.run casing下套管167.running time运转时间168.running tool下人工具169.sand bridge砂桥170.saturatedmlt-water mud饱和盐水泥浆171.sea sick晕船172.seawater mud海水泥浆173.setting slip坐卡瓦174.shallow gas浅层气175.shaly sand泥质砂岩176.short trip短起下177.shut -in关井178.shut-in casing pressure关井套压179.shut-incasing pipe pressure 关井钻杆压力180.sick leave请病假181.side tracking侧钻182.slip drilling line倒大绳183.sloughing,caving(井壁)拥塌184.soda苏打185.soft formation软地层186.solid content固相含量187.spud in开钻188.spud mud开钻泥浆189.squeeze cement 挤水泥190.stage cementing 分级注水泥191.stand-by待命,待机192.stant-by rate待命费193.start up(pump)启动(泵)194.static pressure•静压195.sticking卡钻196.sticking point卡点197.stroke(泵)冲198.swab pressure抽吸压力199.swabbing抽吸200.table height转盘高度201.table torque转盘扭矩202.test paper试纸203.thicking time稠化时间204.thread alternating 错扣205.thread making造扣206.thread off脱扣207.thread slipping滑扣208.tight hole缩径井眼209.tong torque大钳扭矩210.trip起下钻211.tripping time起下钻时间212.troubles事故213.vertical depth垂深214.viscosifier增稠剂215.wait on cementing候凝216.wall thickness壁厚217.wash down开泵循环下放218.wash out section冲刷井段219.water hammer(泥浆泵)水击220.weight on bit钻压221.weighting materials加重材料222.well head now pressure 井口流压223.well location井位224.wiper trip通井225.working instruction作业指令226.working pressure工作压力drilling crew 钻井drill floor,rig floor,floor 钻台drawworks 绞车well-site, rig-site 井场rig manager 平台经理DC (drill collar) 钻铤drilling engineer 钻井工程师DP (drill pipe) 钻杆toolpusher 带班队长rotary table 转盘driller 司钻assistant driller 副司钻derrickman, monkeyman 井架工roughneck, floorman 钻工roustabout 场地工liner 缸套motor fireman 司机wellhead 井口circulation & solid system 循环固控系统machinist 机械师,机工,机械大班electrician 电器师,电工,电器大班operation program 作业程序(指令)cathead 猫头caravan 营房，大篷车tong 大钳elevator 吊卡well depth 井深slip 卡瓦makeup 上扣spud in 开钻breakout 卸扣ROP (rate of penetration),drilling speed, penetration rate 钻速trip 起下钻diesel-engine 柴油机loss circulation 井漏，循环漏失working uniform 工作服brake handle, brake bar 刹把water well condition 井况circulating tank, circulation tank 循环罐normal drilling 正常钻井reserve tank 储备罐parameter 参数trip tank 补给罐，尖底罐, 起下钻泥浆罐rotary speed 转盘转速shale shaker 振动筛pump pressure 泵压WOB (weight on bit) 钻压mesh 目,网孔;啮合,编织torque 扭矩screen cloth 筛布displacement 排量safety meeting 班前会pump stroke 泵冲shift exchange 交班mud pump 泥浆泵master 师傅,主人;征服,控制,精通in charge of 负全责,经营,照顾obtain 获得,得到according to 根据,依照normal 正常的,正规的,标准的introduce 介绍,传入,引进,提出progress 前进,行进,进展supervisor 监督location 井场,井位inspection 检查,考察,验收cellar 方井soild (control) system 固控系统waste pit 污水池、废水池Top Drive (Drilling System)顶(部)驱(动)钻井系统Project Department 项目部on duty 值班modify 整改、修改clinic 医务室electic rig 电动钻机disconnect 拆开,分离,断开pipeline 管线order 指令,命令,顺序Company 公司,甲方Operator 业主,甲方Contractor 承包商,乙方pump house 泵房schedule 时间表,进度表size 尺寸,大小,尺码information 通知,信息,资料equipment 设备,装备,器材instruction 指令,指示,说明书SCR house 可控硅房replace 更换,替换,代替brake shoe 刹车块wear out 磨损safety 安全,保险,安全设备fax 传真guy 家伙,人standpipe 立管Campsite 营地crownblock 天车traveling block 游车dog-house 司钻休息室rat hole 大鼠洞mouse hole小鼠洞spudding inspection 开钻验收fill in 填充catwalk 狭窄的过道,高空走道;高台,天车台casing float collar 套管浮箍casing float valve 套管浮阀casing guide shoe 套管引鞋cement水泥,注水泥,结合剂,胶结剂plug 插头safety pin安全销glove手套quick-connector快速接头fire extingwisher灭火器stretcher担架First Aid紧急救护control board控制板weight mdicator指重表rotary torque indicator转盘扭矩表sling吊绳绳套deadline anchor死绳固定器brake system刹车系统drum滚筒safety line保险绳safety belt安全带hydraulic tong液气大钳slip卡瓦elevator吊卡bit breaker钻头盒chain tong链钳.pipe tong管钳wrench板手pliers钳子、老虎钳scissor剪刀cable slot电缆槽vacuum degasser真空除气器butterfly valve蝶阀desilter除泥器desander除砂器degasser除气器mud gun泥浆枪agitator搅拌器leakage漏,泄漏,渗漏barite重晶石hopper漏斗piston活塞union油壬fuel tank燃油罐、高架罐remote control station远控房BOP stacks防喷器组kill line 压井管线choke line节流管线preventer防喷器annular环空ram闸板low pressure低压fire blanket消防毯fire sand防火砂kitchen厨房storeroom储藏室bathroom卫生间spudding date开钻日期spudding time 开钻时间string钻柱BHA（bottom hole assembly）钻具组合drilling jar震击接头drill box钻杆盒drilling program钻井程序、钻井指令drilling fluid钻井液mix up混和、调配、混淆mud material泥浆材料LCM（lost circulation material）堵漏材料、堵漏剂mud engineer泥浆工程师day tour白班this is the second part, hope it is available for us to learn english for drilling well. the detailed content is as the following:drilling crew 钻井队drill floor,rig floor,floor 钻台drawworks 绞车well-site, rig-site 井场rig manager 平台经理lifting sub 提升短节drilling engineer 钻井工程师bar，crowbar 橇杠rotary table 转盘driller 司钻assistant driller 副司钻derrickman, monkeyman 井架工roughneck, floorman 钻工roustabout 场地工liner 缸套motorman 司机wellhead 井口circulation & solid system 循环固控系统machinist 机械师,机工,机械大班electrician 电器师,电工,电器大班operation program 作业程序(指令)cathead 猫头Kelly 方钻杆tong 大钳elevator 吊卡well depth 井深slip 卡瓦makeup 上扣spud in 开钻breakout 卸扣ROP (rate of penetration),drilling speed, penetration rate 钻速trip 起下钻diesel-engine 柴油机loss circulation 井漏，循环漏失working uniform 工作服brake handle, brake bar 刹把water well condition 井况circulating tank, circulation tank 循环罐normal drilling 正常钻井reserve tank 储备罐parameter 参数trip tank 补给罐，尖底罐, 起下钻泥浆罐rotary speed 转盘转速shale shaker 振动筛pump pressure 泵压WOB (weight on bit) 钻压mesh 目,网孔;啮合,编织torque 扭矩screen cloth 筛布displacement 排量safety meeting 班前会shift exchange 交班mud pump 泥浆泵master 师傅,主人;征服,控制,精通in charge of 负全责,经营,照顾obtain 获得,得到according to 根据,依照normal 正常的,正规的,标准的introduce 介绍,传入,引进,提出progress 前进,行进,进展supervisor,companyman 监督location 井场,井位inspection 检查,考察,验收cellar 方井solid (control) system 固控系统waste pit 污水池、废水池Top Drive (Drilling System)顶(部)驱(动)钻井系统Project Department 项目部on duty 值班modify 整改、修改clinic 医务室electric rig 电动钻机disconnect 拆开,分离,断开pipeline 管线order 指令,命令,顺序Company 公司,甲方Operator 业主,甲方Contractor 承包商,乙方pump house 泵房schedule 时间表,进度表size 尺寸,大小,尺码information 通知,信息,资料equipment 设备,装备,器材instruction 指令,指示,说明书SCR house 可控硅房replace 更换,替换,代替brake shoe 刹车块wear out 磨损safety 安全,保险,安全设备fax 传真guy 家伙,人standpipe 立管Campsite 营地crownblock 天车traveling block 游车dog-house 司钻休息室rat hole 大鼠洞mouse hole小鼠洞spudding inspection 开钻验收fill in 填充catwalk 狭窄的过道,高空走道;高台,天车台casing float collar 套管浮箍casing float valve 套管浮阀casing guide shoe 套管引鞋cement水泥,注水泥,结合剂,胶结剂plug 插头safety pin安全销glove手套quick-connector快速接头fire extinguisher灭火器stretcher担架First Aid紧急救护。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
一、井场设备Equipment on wellsite1 天车 crown2 井架 mast(derrick)3 井架摇臂 cat-line boom4二层台 rackingplatform(monkey-board)5 大绳 drilling line6 游车 traveling block7 大钩 hook8 水龙头 swivel9 水龙带 rotary hose10 立管 standpipe11 绞车（钻机） drawworks12 司钻操作台 driller`s control13 钻杆盒 pipe slacking block14 钻台 drillfloor15 转盘 rotary table16 井架底座 substruture17 封井器总成 blowout preventer stack18 钻台偏房 dog house19 节流管汇 choke manifold20 防喷管线点火头 gas flare21 泥气分离器 mud gas separator22 振动筛 shale shaker23 除气器 degassser24 除砂器 desander25 清洁器 mud cleaner26 离心机 centrifuge27 潜底式泥浆枪 mud guns(bottom type)28 泥浆搅拌器 mud agitators29 泥浆缸 mud tanks30 泥浆药品储备罐 mud sackstorage31 泥浆泥合漏斗 mud mixinghopper32 配泥泵 mud mixing pumps33 泥浆泵 mud pumps34 空气包 pulsation dampeners35 泥浆泵排水软管（短水龙带）shockhoses36 高压管线 mud discharge line37 刹车水罐 brake water tank38 起钻灌泥浆小罐 trip tank39 架空槽（管） mud return line40 泥浆实验室 mud lab41 钻井水罐 drilling water tank42 可控硅房 S.C.R. House43 电缆排 cable tray44 电缆梯（架） cable elevator45 柴油机与发电机 engine&generators46 柴油机与压风机 engine&aircompressors47 配电房 parts storage48 封井器控制台 B.O.P.closingunit49 钳工房 work shop50 泵配件房 pump parts storage51 燃料罐 fuel tank52 乘人电梯 personnel elevator53 大绳架 wire line stand54 大门前跑道 catwalks55 钻杆架 pipe racks提升系统一、天车crown block1 天车 crown block 、crown pulley2 天车台 crown's net 、crownplatform3 天车滑轮 crown sheaves 、crownpulley4 天车滑轮组 cluster sheaves5 天车梁 crownblock beam6 防碰天车 crownblock protector 、crownblock saver7 天车安全台 crownblock plateform二、游动滑车-大钩travelingblock-hook1 游动滑车 traveling block 、travelingsheave2 大钩 hook3 大钩载荷 hook load4 大钩额定载荷 hook load rating5 大钩提升速度 hook speed6 大钩悬重 hook weight7 小钩子 hooklet8 钩上 hook up 、hook on9 大钩悬挂高度 hook height10 卸钩 hook off旋转系统三、钻机Drawworks1 钻机 drilling rig 、drowworks、drilling machine2 司钻操作台 driller's console 、drillercontrol cabinet3 刹把 brake lever、brake crank、brake handle、brake bar4 刹带 brake strap5 刹车凡尔 brake valve6 刹车鼓 brake rim、brake drum7 刹车片 brake block8 刹车液 brake fluid9 刹车轴 brake axle10 刹车功率 brake power11 刹车气缸 brake cylinder12 刹车踏板brake pedal13 刹车总成 brake assembly14 刹带钢圈 brake band15 刹带平衡器 brake equalizer16 水刹车 hydraulic brake17 猫头 cat head18 猫头绳 cat (head) line19 猫头绳小钩 cat hook20 猫头绳滑车 cat line sheave21 猫头轴 cat shaft22 绞车 drawworks23 绞车功率 drawworks horspower24 绞车上的进尺传感器 drawworkssensor四、转盘与水龙头table and swivel1 转盘 rotary table 、turntable、rotary2 转速 rotary speed 、rotationalvelocity、revotion rate3 转盘台 rotating turret4 转盘扭矩表rotary torque indicator5 转速比 ratio of revolution6 转速表 revolution counter、tachometer7 转动方向 rotation direction8 转矩常数 torque constant9 转盘大方瓦 master bushing10 转盘排挡 rotary speeds11 转盘卡瓦 rotary slips12 转盘大梁 rotary support frame13 转盘变速器 rotary tramsmission14 转盘链条护罩 rotary drive guard15 转盘转速指示器 rotary speed indicator16 转盘底座 rotary base17 转盘传动链条 rotary chain18 方补心 rotary drive bushing19 转矩 rotary moment20 转动 rotary motion rotacion21 水龙头 swivel22 水龙头吊环 swivel bail23 水龙头外壳 swivel body24 水龙头吊环防喷器 swivel bumper25 鹅颈管 swivel gooseneck26 冲管 washpipe27 水龙头接头 swivel joint (sub)28 水龙头中心管 swivel stem29 冲管旋转接头 wash pipe swivel 循环系统一、泥浆泵Mud pump1 泥浆泵 mud(slush) pump2 泥浆泵液力端 mud end of thepump3 （口语）泥浆泵 mud hog4 泥浆软管 mud hose5 泵房 mud house、pump room6 泥浆管线 mud line7 泥浆泵软管 mud pump hose8 泥浆泵配浆装置 mud pumpmixer9 泥浆泵压力波动 mud pumppulse10 泥浆泵振动压mud pump shockpressure11 泥浆泵拖车 mud pump trailer12 泥浆泵凡尔 mud pump valve13 泥浆泵安全凡尔 mud reliefvalve14 泥浆泵上水管 mud suctionhose15 泥浆泵拉杆 mud pump rod16 泥浆泵动力端 mud pump powerend17 泥浆泵排出端 discharge end ofpump18 泥浆泵吸入端 suction end ofpump19 泥浆泵排水软管 mud dischargehose20 泥浆泵拉杆盘根 packing ring21 泥浆泵拉杆盘根盒 packingbox22 凡尔座 valve seat23 凡尔体 valve body24 缸套 pump cylinder、pump liner25 活塞 piston piston26 密封圈 rubber seal、sealing ring27 缸盖 cylinder cover(head、lid)28 空气包 air chamber29 空气包气囊 air balloon30 泵体 pump body31 泵箱 pump box32 泵外壳 pump case33 泵的单流凡尔 pump checkvalve34 泵排量 pump discharge、pumpdisplacement35 泵效率 pump efficiency36 泵基础 pump foundation37 泵头 pump head38 泵吸入高度 pump lift、pump suctionhead39 泵负载 pump load40 泵排出管线 pump main41 泵抽空 pump off42 泵过滤器 pump strainer43 泵冲程 pump stroke44 上水凡尔 suction valve45 凡尔座取出器 valve seat puller二、钻井液Drilling fluid1 泥浆 mud、drilling fluid2 泥浆挡板 mud baffle3 泥浆比重称 mud balance4 泥浆储存箱 mud bin5 泥浆结构 mud body6 泥饼桥 mud bridges7 泥饼 mud cake8 泥饼校正 mud cake correction9 泥饼效应 mud cake effect10 泥饼电阻率 mud cakeresistivity11 每分钟泥浆流量加仑数 mudcirculation gallons per minute12 泥浆柱 mud column13 泥浆处理剂 mud conditioner14 泥浆电导率 mud conductivity15 泥浆性能控制 mud control16 泥浆杯 mud cup17 泥浆密度 mud density18 除砂器 mud desander19 泥浆槽 mud ditch、mud flume20 泥浆防漏纤维屑 mud fiber21 泥浆滤液 mud filtrate22 泥浆流 mud flow23 泥浆枪 mud gun24 泥浆（口语） mud laden fluid25 泥浆净化槽 mud launder26 泥浆管线 mud line27 结泥饼 mud lining28 泥浆录井图 mud log29 泥浆录井 mud logging30 泥浆漏失 mud loss31 井漏探测器 mud-lossinstrument32 造浆岩层 mud making formation33 泥浆搅拌器 mud mixer34 泥封 mud off35 泥浆池 mud pit36 泥浆站 mud plant37 泥浆压力计 mud pressure indicator38 泥浆设计 mud program39 泥浆回收 mud reclamation40 泥浆记录 mud record41 泥饼圈 mud ring42 泥浆试样 mud sample43 泥浆比重计 mud scale44 泥浆筛 mud screen45 泥浆分离器 mud separator46 泥浆沉淀池 mud setting sump47 振动筛 mud shaker48 捞砂筒 mud socket49 泥浆稳定性 mud stability50 泥浆流 mud stream51 泥浆罐 mud tank52 泥浆增稠剂 mud thickeners53 泥浆减稠剂 mud thinner54 泥浆比重 mud weight55 泥浆比重天平 mud weight balance56 泥浆比重指示计 mud weight indicator57 泥浆粘度 mud viscosity58 水基泥浆 water-base mud 59 水基混油泥浆 water-base oilemulsion mud60 油包水乳化液 water-in-oilemulsion61 失水量 water loss62 淡水泥浆 water mud63 初切力 gel initial64 静切力 gel of mud65 PH值 PH-value66 PH值记录仪 PH-recorder67 PH值测定计 PH-meter68 含盐量 salt content69 含盐的 salt bearing70 含水的 water bearing71 含砂量 sand content72 盐水泥浆 salt mud73 盐水 salt water、salty water74 盐水基泥浆 salt water basemud75 含盐泥浆 salty mud76 盐析 salting-out动力传动系统一、传动箱（变速箱）Transmission gearbox1 传动箱 gear box、gear case2 换档 gear change3 换低档 gear down4 齿轮传动 gear drive5 齿轮润滑油 gear grease6 齿轮增速器 gear increaser7 齿轮输入轴 gear input shaft8 齿轮传动马达 gear motor9 齿轮油 gear oil10 齿轮输出轴 gear output shaft11 齿轮泵 gear pump12 齿条 gear rack13 传动比 gear ratio14 齿轮减速器 gear reductionunit15 齿轮轴 gear shaft16 换档 gear shifting17 齿轮牙齿 gear teeth18 增速 gear up19 大齿轮 gear wheel20 加速器 accelerator二、柴油机Engines1 柴油机 diesel engine2 柴油 diesel engine fuel、dieseloil oil diesel (diesel oil)3 柴油塞 diesel-oil plug4 柴油耗量 diesel comsumption5 柴油指数 diesel index6 柴油机爆震 diesel knock7 柴油添加剂 diesel fuel additives、diesel-dope8 柴油发电机组 diesel electric set9 引擎 engine motor10 柴油机底座 engine bed11 柴油机本体 engine body12 柴油机泵组 engine and pumpassembly13 柴油机功率 engine capacity14 柴油机气缸 engine cylinder15 柴油机驱动 engine drive16 柴油机防冻液 engine-antifreeze17 柴油机故障 engine failure18 发动机燃料 enginefuel combustible de motor19 柴油机房 engine house、engineshed20 柴油机活塞 engine piston21 柴油机引擎 engine primer22 柴油机皮带轮 engine pulley23 粗柴油 engine solar oil24 柴油机减速器 engine speedreducer25 柴油机支架 engine support26 柴油机并车 engine compound27 调速器 speed regulator、governor28 调温器 thermosistor29 调压阀 pressure-regulatingvalve30 调节滑阀 regulating slidevalve31 调节螺母 adjusting nut32 调节螺栓 adjusting bolt33 调节螺丝 adjusting screw、regulating screw34 调节液 regulating solution35 调节系统 adjusting factor36 调平系统 leveling system37 调平液缸 leveling cylinder38 调速杆 governor lever39 调节范围 adjusting range40 调温冷却器 trim cooler41 风扇 blowing fan、fan42 风扇皮带 fan belt43 固定螺丝 hold-down screw、retaining screw44 固定管板式换热器 fixed tube-sheet exchanger45 气门 valve46 气室 chamber47 气缸垫 head gasket48 气缸盖 cylinder head49 气缸套 cylinder liner50 气缸体 cylinder block51 汽化器 carburetor52 高压泵 high-pressure pump53 高级汽油 high-quality gasoline54 高速柴油机 high-speed engine55 高速机械油 high-speed machine oil56 空气滤子 air filter57 柴油滤子 diesel oil filter58 机油滤子 lubricating oil filter59 油杯 lubricating cup、oil bowl、oil cup60 黄油枪 lubricating gun61 黄油嘴 lubricating nipple62 加油孔 lubrication hole63 加油器 lubricator64 油泵 oil pump65 油尺 dipstick66 油封 oil blanket、oil seal67 油壶 oilcan、oiler、oilpot 68 油环 oil ring、scraper ring、oilrim69 油底壳 oil pan70 油马达 oil motor71 排气阀 air bleeding valve、exhaustvalve72 排气管 blast pipe、exhaust pipe73 排气孔 air vent hole74 排气冲程 exhaust stroke75 排气旋塞 blow cock76 进气管 admission pipe77 水泵 water pump78 散热器 radiator井控装备一、防喷系统BOP system1 井控（防喷） blowout control2 防喷设备 blowout controlequipment3 防喷装置 blowout hookup4 失控喷油井 blowout oil well5 防喷塞 blowout plug6 防喷器 blowout preventer7 防喷四通 spool8 三级密封式防喷器 blowoutpreventer of three stage packer type9 防喷器升高短节 blowout-preventerriser10 防喷器组 blowout preventerunit(stack)11 防喷措施 blowout preventionprocedure12 井喷模拟器 blowout simulator13 环行闸门（万能） annular ram14 半封闸门 pipe ram15 盲板（全封） blind ram16 剪切闸板 shear ram17 液压阀 hydraulic valve18 节流管汇 choke-line manifold19 节流压力 choke pressure20 控制台 control condole21 远程控制台 remote controlconsole22 泥气分离器 gas buster(poorboy)23 除气器 degasser24 方钻杆下旋塞 upper Kelly cock25 方钻杆上旋塞 lower Kelly cock常用工具一、井口工具well head tools1 方补心 kelly bushings2 垫叉 elevator bushings3 滚子方补心 roller type kellybushings4 卡瓦 slip5 安全卡瓦 safety slips6 吊卡 elevator7 吊钳 tongs8 液压大钳 hydraulic tong9 旋扣器 spinner10 旋绳器 spinner11 旋链 spinning chain12 旋绳 spinning rope(line)13 链钳 chain tongs(chainwrench)14 管钳 pipe tongs(pipe spanner)15 方瓦钩子 bushing(tool)hook16 钻杆钩子 drill pipe hoolet二、手工具Hand Tools1 手钳 combination pliers2 扳手 wrench(spanner)3 螺丝刀 screwdriver4 锉刀 file lima5 扁铲 flat chisel6 钢锯 hacksaw sierra7 榔头 club hammer(sledgehammer)8 刮刀 scraper9 手斧 hatchets10 套管扳手 box spanner11 麻花钻 twist drill12 手木钻 gimlet13 玻璃刀 glass cutter14 园顶锤 ball-peen hammer15 羊角锤 claw hammer16 十字螺丝刀 phillips screwdriver17 丁字镐 pick18 梅花扳手（套换扳手） ringspanner19 剪刀 scissors20 试电笔螺丝刀 electricalscrewdrivers21 开口扳手 open-ended spanner22 扭矩扳手 torque wrench安全Safety1 安全允许应力 safe allowable stress2 安全区 safe area3 安全空气环境 safe atmosphere4 安全承载 safe bearing load5 安全浓度 safe concentration6 安全保管 safe custody7 安全距离 safe distance8 安全点火地带 safe fire zone9 护罩（安全措施） safeguard10 保护位 safeguard bit11 保护措施 safeguard clause12 安全处理规程 safeguard procedures13 安全规则 safe-handling procedure14 安全传热 safe rules15 妥善保护 safe heat transfer16 安全限度 safekeeping17 安全限制 safe level18 安全载重 safe limit19 安全操作 safe load20 安全技术 safe operation21 （不出砂的）安全产量 safe practice22 安全可靠性 safe reliability23 安全应力 safe stress24 安全报警器 safety alarm device25 安全分析技术 safety analysis technique26 保险装置 safety apparatus27 防护用具 safety appliance28 安全制动 safety arrestment29 保险带 safety belt30 安全放泄阀 safety bleedervalve31 架工安全操作台 safety board32 安全箱 safety box33 保险刹车 safety brake34 安全旁通管 safety by-pass35 保险索 safety cable36 安全帽 safety cap37 安全档 safety catch38 安全证书 safety certificate39 安全链 safety chain40 安全检查器 safety checker41 安全卡子 safety clamp42 安全间隙 safety clearance43 安全离合器 safety clutch44 安全规程 safety code45 安全系数 safety coefficient46 安全色标 safety color47 安全控制头 safety controlhead48 安全连接器 safety coupling49 安全熔断器 safety cut out50 安全检测器 safety detector51 安全雷管 safety detonator52 安全设备 safety equipment53 安全评价 safety evaluation54 安全排气管 safety exhaust55 安全系数 safety factor56 安全性能 safety feature57 安全照明灯 safety flare58 保险丝 safety fuse59 保险齿轮（档） safety gear60 安全玻璃 safety glass61 护目镜 safety goggles62 安全接地 safety ground63 安全接地装置 safety groundingdevice64 安全带 safety harness65 安全帽 safety hat(helmet)66 安全起重机 safety hoist67 安全大钩 safety hook68 安全生产 safety in production69 安全检查员 safety inspector70 安全接头 safety joint71 安全梯 safety ladder72 安全灯 safety lamp73 保险销 safety latch74 安全液面 safety level75 安全照明 safety lighting76 保险绳套 safety link77 安全琐销 safety locking pin78 安全琐线 safety lockwire79 安全储备（余额）safety margin80 安全措施 safety measures81 安全网 safety net82 安全标志 safety notice83 保险螺帽 safety nut84 安全作业区 safety operationarea85 安全销 safety pin86 安全预防措施 safetyprecaution87 安全计划 safety program88 安全记录 safety record89 安全守则 safety regulation90 断路继电器 safety relay91 安全泄电器 safety relief valve92 保险绳 safety rope93 安全罩 safety screen94 安全密封封隔器 safety sealpacker95 安全传感器 safety sensor96 安全止动螺钉 safety set screw97 安全剪切接头 safety shearsub98 安全鞋 safety shoes99 安全隔断阀 safety shutdownvalve100 安全滑车 safety slide101 安全卡瓦 safety slip102 安全卡盘 safety stirrup103 安全库存量 safety stock104 安全限位档块 safety step105 安全带safety-strap106 保险开关 safety switch107 安全技术 safety technique108 安全阀门座 safety valve seat109 安全阀 safety valve110 安全电压 safety voltage111 安全垫圈 safety washer112 安全重量 safety weight113 安全工作压力 safety working pressure114 额定安全工作压力值 safety working pressure rating一、套管Casing1 套管 casing2 套管附件 casing accessories3 下套管的井 cased borehole4 下套管完井 cased hole completion5 全部下套管的井 cased through well6 下套管 case in7 套管异径接头 casing adapter8 套管锚 casing anchor9 套管环空 casing annulus10 下套管工具 casing appliances11 下套管地层 casing-bearing formation12 套管打捞筒 casing bowl13 套管桥塞 casing bridge plug14 套管弯曲 casing buckling15 扶正器 casing centralizer16 回压凡尔 casing check valve17 套管卡子 casing clamps18 套管挤坏 casing collapse19 套管接箍 casing collar20 套管接箍测定器casing collar location21 测套管接箍 casing collar log22 套管连接 casing connection23 套管腐蚀监casing corrosion monitoring24 套管联接器 casing coupling25 套管割刀 casing cutter26 套管割刀震击器 casing cutterjar27 套管割刀加力器 casing cuttersinker28 套管损伤 casing damage29 套管变形 casing deformation30 套管深度 casing depth31 套管打捞矛 casing dog32 套管整形器 casing drift swage33 砸套管护帽 casing drive head34 砸击套管鞋 casing drive shoe35 套管吊卡 casing elevator36 套管损伤 casing failure37 套管配件 casing fitting38 回压凡尔 casing float39 套管鞋 casing float shoe40 套管丝扣规 casing gauge41 套管钢级 casing grade42 引鞋 casing guide shoe43 套管悬挂器 casing hanger44 套管附件 casing hardware45 套管头 casing head46 套管头内卡瓦座 casing headbowl47 套管头压力 casing headpressure48 套管头四通 casing head spool49 套管头挤水泥 casing headsqueeze50 套管与井壁环空 casing-holeannulus51 套管大钩 casing hook52 套管缺陷 casing imperfection53 套管探伤 casing inspection54 检查套管测井 casing inspectionlog55 下套管 casing installation56 套管千斤顶 casing jack57 下套管作业 casing job58 一节套管 casing joint59 套管割刀 casing knife60 联顶节 casing landing61 套管漏 casing leak62 裸眼完井 casingless-completion63 胀管器 casing mandrel64 套管铣鞋 casing mill65 套管磨铣工具 casing millingtool66 套管短节 casing nipple67 套管封隔器 casing packer68 套管修补 casing patch69 套管补孔器 casing patch tool70 套管射孔器 casing perforator71 套管鞋深度 casing point72 套管紧扣杆 casing pole73 套压 casing pressure74 套管试压 casing pressure test75 套管程序 casing programme76 套管护箍 casing protector77 刮管器 casing scraper78 套管母扣护丝 casing screwhead79 套管公扣护丝 casing screwprotector80 套管密封件 casing seal81 套管铣刀 casing section mill82 套管下入深度 casing settingdepth83 割套管 casing severing84 套管侧钻 casing side tracking85 套管尺寸 casing size86 套管卡瓦 casing slip87 套管捞矛 casing spear88 套管卡盘式吊卡 casing spider89 套管裂纹 casing split90 套管割刀 casing splitter91 入井第一节套管 casing starter92 套管粘卡 casing sticking93 套管柱 casing string94 套管柱设计 casing stringdesign95 套管异径接头 casing sub96 套管悬挂器 casing suspender97 胀管器 casing swage98 套管旋转头 casing swivel99 捞套管公锥 casing tape100 套管测试器 casing tester101 套管螺纹 casing threads102 套管井壁环空 casing-to-holeannulus103 套管容积 casing volume104 管壁 casing wall105 套管磨损 casing wear106 套管造斜器 casing whipstock 107 拔套管 casing withdrawal 108 套管重量 casing wt、casing weight二、钻柱drilling string1 钻头 bit(rock bit)2 配合接头 cross-over sub3 减振器 bumpers(shock absorber)4 随钻打捞杯 drilling junk basket5 无磁钻铤 Monel drill collar ,Non-maganetic6 钻铤 drill collar7 扶正器 stabilizer estabilizador8 螺旋钻艇 spiral drill collar9 随钻震击器 drilling jar10 柔性短节 flex joint11 加重钻杆 heavy wall drillpipe(HWDP)12 钻杆 drill pipe13 回压凡尔 back pressure valve14 方保接头 kelly sub(save sub)15 方钻杆 kelly16 方入 kelly-in(kelly-down)17 方余 kelly-up18 正扣 right band thread19 反扣 left hand thread20 母接头 tool joint box21 公接头 tool joint pin22 单根 single23 双根 double 24 立柱 stand(thrible) columna、三、复杂情况与事故Trouble andaccidents1 跳钻 rough drilling(bouncing ofdrilling tool)2 憋钻 bit bouncing3 溜钻 drilling string not well braked4 顿钻 percussion drill5 打倒车 reverse rotation(running)6 井斜 hole deviation(inclination)7 纠斜 correct drift8 填井 plug-back9 打水泥塞 cementing plug10 侧钻 cidetracking11 井漏 lost circulation12 井塌 slough(cace-in)13 井涌 kick14 井喷 blowout15 卡钻 stuck(sticking)16 粘卡 differential sticking(wallsticking)17 键槽卡钻 key-seating sticking18 砂桥卡钻 sand bridge sticking19 沉砂卡钻 sand settling sticking20 遇阻 touchdown(touchingresistance)21 遇卡 touch sticking22 对扣 make-up(stab)23 造扣 thread making24 倒扣 back-off25 拔活塞 pulling a piston26 打捞 fishing27 解卡剂 releasing stuck agent(pipelax)28 泡解卡剂 black magic to soak withblack magic29 爆破松扣 break outing pack ofdynamite30 化学切割器 chemical cutter31 钻头泥包 bit balling (balling up ofa bit)32 卡点 free point33 扭断 to twist-off34 挤水泥 squeeze cementing35 解卡 unfreezing，releasing stuck四、钻井人员Drilling Personnel1 总裁 president2 总经理 general manager3 钻井监督 drilling supervisor4 钻井工程师 drilling engineer5 泥浆工程师 mud engineer6 定向井工程师 directionalengineer7 机械师 mechanical engineer8 电器工程师 electric engineer9 钻井队长 toolpusher10 钻井技术员 drilling technician11 工长 foreman12 司机长 principal engineman13 司钻 driller14 司机 engine(motor)man15 司助 assistant motorman16 发电工 generator keeper17 井架工 derrickman18 内外钳工 floorman19 场地工 roustabout20 泥浆工 mudman(mudboy)21 地质工 geo-sampler22 炊事员 cook23 服务员 attendant24 副总裁 vice president25 副经理 deputy manager26 副司钻 assistant driller27 汽车司机 driver28 库房保管员 storekeeper29 安全员 security official30 成本会计员 cost accountant31 材料员 material handler, man32 会计员 accountant33 话务员 operator34 翻译 interpreter35 总工程师 chief engineer36 主任工程师 principal engineer37 总会计师 general accountant38 总地质师 general geologist39 总设计师 chief designer40 董事长 chairman41 平台经理 Rig manager42 作业监督 operation supervisor43 机械监督mechanic supervisor44 电器监督 electrical supervisor45 设备监督 equipment supervisor46 安全监督 safety supervisor47 环境监督 environmental inspector48 钻工 floor men 五、常用钻井词汇Useful Words of Drilling1 钻井 drill(make hole)2 可钻性 drillability3 可钻碎的 drillable4 可钻式尾管悬挂器 drillable liner5 可钻式封隔器 drillable packer6 可钻式永久封隔器 drillable permanent packer7 继续钻井 drill ahead8 钻柱组合 drillstring combinations9 钻头 drill bit10 钻头行程 drill bit run11 钻井钢丝绳 drill cable12 钻铤 drill collar13 钻铤环空 drill collar annulus14 钻铤水眼 drill collar bore15 钻铤弯曲度 drill collar curvature16 钻铤应力减轻槽 drill collar groove17 钻铤提升短节 drill collar lifting nipple18 钻铤扶正器 drill collar stabilizer19 钻铤刚度 drill collar stiffness20 取心井 drill core sample hole21 钻井队 drilling crew22 岩屑 drill cuttings(solids)23 已钻区 drilled area24 水泥碎屑 drilled cement25 干钻 drilled dry26 已钻进尺 drilled footage27 钻头切削刀 drill edge 28 已钻通的 drilled in29 钻入桩脚 drilled pile30 钻探储量 drilled reserves31 钻进显示 drilled show32 完钻井 drilled well33 司钻 driller34 钻机台月 driller-month35 司钻控制台 driller's console36 司钻小型控制台 driller's controlcabinet37 司钻记录 driller's log38 司钻法（压井） driller's method39 司钻监视器 driller's monitor40 司钻（平）台 driller station41 钻井班报表 driller reporter42 钻头打捞器 drill extractor43 钻台 drill floor44 钻井液 drill fluid45 钻井进尺 drill footage46 钻头离开井底空转 drill free47 钻头规 drill gauge48 井眼 drill hole49 井口返出泥浆 drill-hole returns50 井距 drill-hole spacing51 测井斜 drill-hole survey52 打开生产井 drill-in53 下套管后再开井 drilling ahead54 钻井分析 drilling analyticalwork55 钻头 drilling bit56 钻探井租地 drilling block57 钻进中放空 drilling break58 钻机能力 drilling capacity59 钻井扶正器 drilling centralizer60 钻井用粘土 drilling clay61 完井作业 drilling completionoperation62 完井方案 drilling completionprogram63 钻井条件 drilling condition64 钻井合同 drilling contract65 钻井成本 drilling cost66 钻杆接箍 drilling coupling67 钻井队 drilling crew68 岩屑 drilling cuttings69 钻井周期 drilling cycle70 钻井污染区 drilling damagezone71 钻井数据库 drilling data base72 钻井工作量 drilling effort73 钻井工程师 drilling engineer74 钻井工程（学） drillingengineering75 钻井工程录井仪 drillingengineering data logging unit76 钻井设备 drilling equipment77 钻井开支 drilling expenditure78 钻井经验 drilling experience79 钻井专家 drilling expert80 循环系统 circulating system81 净化系统 drilling system82 进尺 drilling footage83 钻井队长 drilling foreman84 水龙带 drilling hose85 钻井人员 drilling implementer86 压力平衡钻进 drilling-in-balance87 钻井仪表 drilling instrument88 钻进井段 drilling interval89 钻井楼层 drilling invasionzone90 随钻震击器 drilling jar91 钻井记录表 drilling journey92 钻井大绳 drilling line93 尾管 drilling liner94 尾管固井 drilling linercementing95 大绳滚筒 drilling line reel96 尾管悬挂器 drilling linerhanger97 钻压 drilling load98 钻进录井 drilling log99 双腿井架 drilling mast100 钻速方程 drilling model101 钻进监控系统 drilling monitorsystem102 泥浆 drilling mud103 钻井作业 drilling operation104 钻井经营者 drilling operator105 优化钻井 drilling optimization106 钻水泥塞 drilling out107 钻井设备 drilling outfit108 钻井参数 drilling parameter109 钻井优化参数 drilling parameteroptimization110 井位布置 drilling pattern111 钻井人员 drilling people112 钻井许可权 drilling permit113 钻井阶段 drilling phase114 钻井平台 drilling platform115 钻井实践（作业） drilling practice116 钻井预报 drilling prediction117 钻井泵压 drilling pressure118 钻井程序 drilling program119 钻井进度 drilling progress120 钻井研究开发部 drilling R andD121 钻速Rate of Penetration , drilling rate122 钻速方程 drilling rate model123 行程钻速 drilling rate of a trip 124 钻速记录仪 drilling rate recorder125 钻井记录 drilling record126 钻井船 drilling ship(vessel)127 钻井模拟器 drilling simulator 128 井场 drilling site129 钻井专家 drilling specialist130 钻速 drilling speed131 防喷器下的四通 drilling spool 132 钻柱 drilling stem(string)133 钻柱扶正器 drilling string stabilizer 134 钻井总监 drilling superintendent135 钻井监督 drilling supervisor136 钻井技术 drillingtechnique(tech)137 钻井技术员 drilling technician 138 钻井工艺 drilling technology 139 钻井供应船 drilling tender 140 钻井时间 drilling time141 钻时记录 drilling time log 142 钻速记录仪 drilling time recorder143 钻至设计井深 drilling to completion144 钻具 drilling tool钻井英语缩写AbbreviationDP drill pipe 钻杆DC drill collar 钻铤SMDC short (pony) magnetic drill collar 短无磁钻铤PDM positive displacement motor 螺杆NMDC nonmagnetic drill collar 无磁钻铤（钻具）BOP blowout preventer 封井器XO cross-over 配合接头IF internal flush 内平REG regular 正规EU external upset 外加厚IEU internal & external upset 内外加厚WOB weight on bit 钻压SPM strokes per minute 冲程每分钟ECD equivalent circulating density 当量泥浆密度MT metric ton 公制吨DST drill stem test 钻具测试STDS stands 立柱WL water loss 失水YP yield point 屈服值TVD total vertical depth 垂深TD total depth 总井深DIR direction 定向DEV deviation 井斜ID inside-diameter 外径PPG pounds per gallon （密度）每加仑磅PSI pounds per square inch每平方英寸磅HTHP high temperature highpressure 高温高压LCM lost circulation material堵漏剂API American petroleuminstitute 美国石油协会IADC International associationdrilling contractor 国际钻井承包商CNPC China national petroleumcompany 中国石油天然气总公司P/N part number 零件型号N/W net weight 净重P/U pick up 吊起L/D lay down 甩开N/D nipple down 卸开WOC wait on cement 侯凝WOO wait on order 等指令DR drilling 钻进WOW wait on water 等水SX sacks 大袋CBU circulate bottoms up 循环一周MWD measurement while drilling 随钻测量HWDP heavy weight drill pipe 加重钻杆STB stabilizer 钻杆扶正器CSG casing 套管JNT joint 单根FH full hole 贯眼IU Internal upset 内加厚OH open hole 裸眼RPM revolutions per minute 转速分钟BHA bottom hole assembly 底部钻具组合KS key seat 键槽VIS viscosity 粘度PV plastic viscosity 塑性粘度FL filtrate loss 滤失MD measured depth 测量井深KOP kick off point 造斜点AZM azimuth 方位ROP rate of penetration 机械钻速FTG footage 进尺SGL single 单根AD assistant driller 副司钻S/N serial number 系列号G/W gross weight 毛重M/U make up 接上N/U nipple up 接上R/U rig up 安装RIH run in hole 下钻POOH pull out of hole 起钻RM reaming 扩眼（划眼）TOF top of fish 鱼顶MW mud weight 泥浆密度TOH trip out of hole 起钻KSW key seat wiper 键槽清洁器。