人脸识别测温面板机快速使用说明书
人脸识别测温面板机快速使用说明书
阁下，您好！
感谢您选购本公司的人脸识别测温面板机产品。
为了使您更好的使用本产品，使用之前请仔细阅读本使用手册。
产品清单：
人脸识别测温面板机
电源适配器适配连接线束配件袋产品保修卡
立式安装柱
（闸机安装款配）
壁挂安装支架
（墙体安装款配）
安装建议 壁挂式安装建议：
安装高度：摄像头高度约1.4米处；
安装位置：尽量避免摄像头直对正东、正西方向，镜头长时间正对太阳照射可能会影响镜头使用寿命，及识别速度、准确率。
闸机立柱安装步骤：
闸机开孔孔径：用激光、液压开孔器开M34孔；
安装位置：尽量避免摄像头直对正东、正西方向，镜头长时间正对太阳照射可能会影响镜头使用寿命，及识别速度、准确率；
1.4m
地面
凤凰端子接线示意图 接线说明：
①剥开电线，露出金属丝；②按下小孔对应的橙色按钮，将金属线头插入孔中，松开橙色按钮后线头固定（其他线接法如此）
设备接口：
注意事项
请注意供电电源位置及+5v 输出电压位置，区分好凤凰口1和凤凰口2，防止接反烧坏外接设备。
注意网线的接线顺序防止网络不通。
备注：电源正负极接正确后设备才能正常启动；电源适配器需12V 2A
人脸识别使用说明
可根据身高来适当调整人员和设备的距离，较高的人适当往后站，较矮的人适当往前站。
0.5~3m都是较好的识别距离。
从上往下看，以设备为圆心，距离3m 内属于可识别。
测温使用说明
1.热像仪开机后，需预热10分钟；
2.测量时，请确保距离在30~50CM，测量时间两秒钟以上；
2.推荐使用在室内场景，使用环境温度20~30℃；
3.严禁阳光直射镜头，将对镜头产生不可逆的损坏；
4.测温时，为保证数据精准性，避免镜头朝向空调等热源，阳光、玻璃反射以及风吹，并规避测量人体受热源影响。
人脸识别终端系统使用说明书
人脸识别产品使用说明2021-04目录第1章硬件说明................................................................................................................................1.1主板接口说明.......................................................................................................................1.2产品尾线接线说明...............................................................................................................第2章设备界面说明........................................................................................................................2.1界面概览...............................................................................................................................2.2进入管理界面.......................................................................................................................2.3基本参数...............................................................................................................................2.4识别参数...............................................................................................................................2.4.1测温功能....................................................................................................................2.4.2识别参数....................................................................................................................2.4.3人脸识别....................................................................................................................2.4.4身份证识别................................................................................................................2.4.5IC卡识别.....................................................................................................................2.5网络设置...............................................................................................................................2.6名单管理...............................................................................................................................2.6.1查询............................................................................................................................2.6.2添加名单....................................................................................................................2.6.3名单详情....................................................................................................................2.6.4删除名单....................................................................................................................2.7识别记录...............................................................................................................................2.7.1查找............................................................................................................................2.7.2识别详情....................................................................................................................2.7.3删除记录....................................................................................................................2.8外设配置...............................................................................................................................2.9平台设置...............................................................................................................................2.10系统维护.............................................................................................................................2.11系统信息.............................................................................................................................第1章硬件说明1.1主板接口说明1.2产品尾线接线说明第2章设备界面说明2.1界面概览设备端接入电源开机，系统会自动进入实时人脸识别界面⚫顶部区域：IP地址、设备日期、设备时间、红外成像视频；⚫中间区域：人脸识别区域、识别信息提示框；⚫底部区域：设备标语、底库人数、网络接入标识、身份证阅读器接入标识、测温模块接入标识、人员信息同步进度标识、mac地址。
汉王人脸识别设备 使用说明说明书
汉王人脸识别设备使用说明北京汉王智远科技有限公司2019年9月目录第一部分管理员操作 (1)一、管理员添加 (1)二、管理员登陆 (2)三、管理员编辑 (2)四、人员管理 (3)1、用户列表 (3)2、访客列表 (5)3、黑名单 (5)4、容量 (6)5、人员编辑 (6)五、记录管理 (11)1、记录列表 (11)2、容量 (12)3、导出 (12)4、导出记录信息 (13)六、设置 (13)1、网络设置 (14)2、识别设置 (16)3、云识别 (17)4、系统设置 (18)5、导出设置 (26)6、导入设置 (26)七、还原 (26)八、设备信息 (27)第二部分员工使用 (27)1、人脸 (27)2、刷卡 (28)3、刷卡＋人脸 (28)4、身份证/ID (28)5、身份证/ID＋人脸 (29)6、刷卡＋身份证/ID (29)第三部分硬件设备相关 (30)一、产品简介 (30)二、外观介绍 (30)三、产品功能 (30)四、规格参数 (31)第一部分管理员操作一、管理员添加设备开机后，初次使用为未设置管理员状态，见图1；点击“添加管理员”按钮，弹出输入管理员用户名和密码界面，见图2；图2信息添加完毕后，点击“确定”按钮，进入人员模板录入界面，见图3，添加成功，弹窗提示，2秒后弹窗消失，进入识别界面。
图1 图2 图3设备开机后，非初次使用添加管理员方式如下，识别界面，点击“主功能键”----点击“管理员”，如图4所示，通过刷已有管理员人脸或者已有管理员密码进入“设置列表”----“设置”----“系统设置”----“管理员设置”----“管理员录入”----“添加人脸”，弹出输入管理员用户名和密码界面，见图5；图5信息添加完毕后，点击“确定”按钮，进入人员模板录入界面，见图6，添加成功，弹窗提示，2秒后弹窗消失，进入识别界面。
图4 图5 图6二、管理员登陆设备开机后，识别界面，点击“主功能键”----点击“管理员”，如图7所示，通过刷已有管理员人脸，如图8所示；或者已有管理员密码，如图9所示，进入“设置列表”。
人脸识别测温终端使用说明书
人脸识别测温终端使用说明书一、型号☐DM1071-T☐____________二、产品规格参数基础参数主控芯片高性能AI SoC（4核A7+NPU+DSP）内存1GB DDR3高性能内存存储器板载8GB高速eMMC测温及识别要求识别高度 1.2~2.2m，角度可调识别距离0.5~1.2米人脸角度左右30度，上下30度人脸识别人脸识别精度99.99%（1:1，FRR1%)活体检测支持识别速度<300ms（2W人脸底库）人脸库默认2W，最大5W 1:1人脸对比支持1:N人脸搜索支持红外热成像测温精度≤±0.3℃测温范围20℃~45℃热成像像素120*90（共计10800个像素点）报警体温异常报警支持（体温报警阈值可设置）未戴口罩报警支持（可设置）网络LAN RJ45，100MWi-Fi 2.4G，802.11b/g/n屏幕尺寸7英寸分辨率600*1024摄像头分辨率200万类型120DB超宽动态双目摄像头补光灯内置补光灯，无惧逆光、暗光环境接口电源DC12V网络1个RJ4510M/100M自适应以太网口USB1路USB2.0接口锁控1路锁控信号可选1路接口,可选RS232/UART电气参数电压DC12V 电流500mA 功率15W工作温度20~35℃存储温度-25~60℃装箱清单主机*1，电源适配器*1，电源转接头*3（美标、英标、欧标)，螺丝*8，合格证*1支架*3（桌面式、壁挂式、立柱式）三、接口说明四、安装方式壁挂式：1、根据壁挂式支架A的6个固定孔位的位置，在墙壁做好定位标注；用冲击钻将孔位钻好后，用膨胀螺丝将支架A固定好；2、使用自带螺丝将主机支架B更换成壁挂式，并将主机卡扣B卡在墙壁支架A处；3、使用自带螺丝在C处将支架A和B固定在一起，连接电源即可。
立柱式：1、根据闸机类型和实际使用场景，在闸机的适当位置开孔，参考直径为34.2mm；2、将立柱最下方的螺母A拧下，脱离整个主机和线缆；3、从孔位的上方，先将线缆依次穿过孔位，并将立柱插入孔位，再从闸机下方，将线缆依次穿过螺母A；4、将螺母拧紧，连接电源、韦根和灯即可。
人脸识别测温一体机-AI-321详细操作指南说明书
人脸识别测温一体机操作指南型号：AI-321V2.1目录1．产品概要说明2．公司人脸识别测温模式3．企业门禁考勤管理软件使用说明4．本地服务部署说明5．校园人脸识别测温模式6．校园门禁考勤管理软件使用说明7．快速温度筛查模式1．产品概要说明本设备提供3种使用模式：公司人脸识别测温，校园人脸识别测温和快速温度筛检，用户可根据需要选择合适的应用模式。
1.1 公司人脸识别测温该模式可对公司员工进行温度检测和身份识别，同时完成测温、考勤和门禁功能。
该模式需要跟企业门禁考勤管理软件一起配合使用。
1.2 校园人脸识别测温该模式可对学生进行温度检测和身份识别，同时完成测温、考勤和门禁功能。
该模式需要跟校园门禁考勤管理软件一起配合使用。
1.3 快速温度筛检该模式只进行温度检测，可实现测温和门禁功能。
该模式可以跟体温云APP 一起配合使用，通过APP查看数据。
2．公司人脸识别测温模式2.1. 登录企业门禁考勤管理软件完成以下操作：∙添加设备ID（设备ID号显示在设备主界面左上角）∙设置考勤规则∙录入员工基本信息∙录入员工照片∙为员工分配考勤设备和考勤规则（此步骤非常关键，否则考勤设备将无法同步到数据）具体操作方式详见企业门禁考勤管理平台软件使用说明。
2.2. 配置设备联网点击界面右上角网络按钮进行如下设置：∙域名设置直接使用本公司提供的门禁考勤管理云服务的用户可直接省略此步骤。
需要自行部署门禁考勤管理服务到本地的用户需要修改域名地址为实际使用的服务器IP地址。
具体操作详见本地服务部署说明。
∙网络设置用户可选择WIFI或以太网两种方式配置设备联网直接使用本公司提供的门禁考勤管理云服务的用户，只需配置设备连接外网即可。
使用本地服务器的用户，需要配置设备能够访问到本地服务器。
∙设备联网成功设备成功连接到服务器，并已经完成了2.1所述操作的用户，可以看到设备主界面左上角的文字提示消失，变成了菜单图标。
2.3. 设置操作码并同步数据∙点击菜单按钮会首先要求设置操作码用户可自行设置一个操作码，后续点击菜单图标都需要输入用户设置的操作码才可以查看菜单项。
人脸门禁一体机 用户操作手册说明书
人脸门禁一体机目录第1章注意事项 (7)第2章概述 (10)2.1产品简介 (10)2.2产品功能 (10)第3章外观介绍 (12)3.1尺寸（mm） (12)3.2外观图 (13)第4章安装说明 (14)4.1安装环境 (14)4.2安装步骤 (14)第5章接线说明 (16)5.1 接线端子说明 (16)5.2 接口应用说明 (17)第6章设备激活 (18)6.1 通过本地设备激活 (18)6.2 WEB激活 (18)6.3 修改设备IP (19)第7章WEB端操作说明 (20)7.1 登录 (20)7.2 预览 (20)7.3 回放 (23)7.4 日志查询 (26)7.5 配置 (26)7.5.1 常用设置 (27)7.5.2.1 音视频参数-视频参数 (30)7.5.2.2 音视频参数-音频参数 (32)7.5.2.3 音视频参数-图像设置 (33)7.5.3 网络设置 (37)7.5.3.1 基本设置 (37)7.5.3.2 高级设置 (40)7.5.4 报警设置 (47)7.5.4.1 报警管理 (47)7.5.5 门禁管理 (50)7.5.5.1 人员管理 (50)7.5.5.2 数据管理 (57)7.5.5.3 计划模板 (59)7.5.6 存储 (61)7.5.6.1 录像策略 (61)7.5.6.3 磁盘管理 (63)7.5.6.4 网络存储 (64)7.5.7 系统设置 (67)7.5.7.1 系统设置 (67)7.5.7.2 用户管理 (69)7.5.7.3 系统维护 (70)7.5.7.4 本地设置 (73)第8章设备本地操作 (75)8.1 激活及管理员登录 (75)8.1.1激活 (75)8.1.2管理员登录 (76)8.2 通讯设置 (78)8.2.2 韦根设置 (80)8.3 用户管理 (80)8.3.1 添加用户 (80)8.3.2 添加用户卡片 (82)8.3.3密码设置 (83)8.3.4 添加用户人脸 (84)8.3.5设置认证方式 (84)8.4 数据管理 (86)8.5 记录查询 (87)8.5.1 记录查询 (87)8.5.2 事件查询 (88)8.6 门禁设置 (89)8.7 系统设置 (90)8.7.1 系统信息 (91)8.7.2 人脸参数 (92)8.7.3 时间设置 (93)8.8 系统信息 (94)8.8.1 记录容量 (95)8.8.2 设备信息 (95)第9章人脸录入注意事项 (96)9.1 人脸照片录入要求 (96)9.2 人脸姿态 (96)9.3 人脸录入位置 (97)第十章公司声明 (98)附录一外置读卡器使用说明 (99)第1章 注意事项欢迎您选购我司的产品，如果您在使用中遇到任何疑问，请向经销商或我司售后服务咨询。
汉王B211版人脸识别机使用手册
汉王人脸识别机使用手册汉王科技股份有限公司目录第一部分使用概述 (1)第一章前言 (1)第二章设备外观介绍与快速安装指南 (2)设备外观介绍 (2)快速安装指南 (5)第二部分管理员配置与操作 (7)第一章管理员配置 (7)进入管理员模块 (7)登记管理员 (8)管理员配置 (10)第二章管理员操作 (11)管理员验证 (11)功能菜单 (12)用户管理 (13)登记用户 (13)修改用户 (14)删除用户 (16)清空用户 (16)记录管理 (17)查询记录 (17)清空记录 (18)U盘功能 (19)导出考勤记录 (19)导出部分用户 (19)导出全部用户 (19)导出管理员 (19)导入部分用户 (19)导入全部用户 (20)导入管理员 (20)导入工号姓名列表 (20)固件升级 (20)系统设置 (21)设置系统时间 (21)音量调节 (22)设置网络及密码 (22)设置时间间隔 (23)设置上下班时间 (23)恢复出厂设置 (24)系统信息 (25)容量信息 (25)产品信息 (25)第三部分普通用户使用 (26)用户识别 (26)人脸识别 (26)工号人脸识别 (26)识别成功 (28)附录 (29)技术规格 (29)注意事项 (30)注意：本手册所介绍的内容和使用的图片仅供参考，根据产品型号和使用状况，可能有所不同，以产品为准。
为加强本产品的正确性、设计及功能，制造商可能不另行通知即更新产品信息，以产品为准。
汉王科技股份有限公司保留对本手册的最终解释权。
第一部分使用概述第一章前言汉王科技，十几年来一直专注于模式识别领域。
2008年，汉王科技突破国外技术垄断，全力推出一系列人脸识别技术及其产品。
本产品识别速度快，准确率高，专门针对需要脱机使用的企事业单位考勤管理而设计。
产品采用彩色屏幕，人机交互更加直观友好；非接触、方便、卫生、快捷地完成人脸识别；此外还支持TCP/IP通信和U盘上传/下载功能，非常适合企事业单位的考勤管理。
测温人脸识别门禁一体机说明书
测温人脸识别门禁一体机说明书型号：AI-SID007版本：V 2.0商标本手册所提及的商标与名称都归其所属公司所有。
注意事项1、使用前，请先详细阅读说明书，避免误操作导致产品损坏；2、请将此产品放置-15℃≤工作环境≤60℃、90%RH 环境下，以免因过冷、热或受潮导致产品损坏；3、请勿将此产品做强烈的机械运动，以及在没有做好静电防护之前对此产品操作；4、在安装任何外接卡或模组之前，请先关闭电源；5、请确保外接入电源为12V 3A，以免造成主机损坏；6、禁止对设备进行拆机，禁止对主板进行私自更改、拆焊，否则我们对此所导致的任何后果不承担责任。
目录商标 (2)注意事项 (2)一、产品概述 (4)二、产品规格 (5)三、设备接口介绍 (6)四、机械尺寸图 (7)五、设备安装示意图 (8)六、终端程序说明图示 (9)一、产品概述感谢您选购人脸识别门禁一体机1、人脸识别门禁一体机是一款使用人脸识别技术来控制门口通行的设备，壁挂于门口边缘，把人脸识别技术完美地融合到门禁产品中去，通过摄像头采集人脸信息，经过图像比对算法后实现人脸识别，最后实现门禁进出控制、考勤、访客管理等功能。
2、产品特点1）刷脸进出，解放双手，不怕丢钥匙，不怕一手抱娃一手提包，不用麻烦别人开门，增加用户无感通行的美好体验；2）对考勤进行精准记录，防止传统门禁的盗刷、代打卡问题，比钉钉打卡更精准；3）体温检测，体温异常报警4）解决传统指纹考勤痛点，指纹卫生问题关系你我他；5）可实时进出推送，让你无时无刻知道公司情况；6）外传专利，设计精美，高端大气上档次；7）实时路人抓拍，陌生人推送给管理员，更安全；3、应用场景：小区、园区、写字楼、办公室、实验室、工厂、机关单位、旅游区、学校等，有门的地方都可以使用。
二、产品规格参数三、设备接口介绍1、电源输入接口DCx12、USB接口2个（可接USB鼠标、U盘等外设）3、Rj45网口------有线网口1个4、串口输出，支持232\485，默认485输出，可选配维根输出，串口和维根只能2选15、继电器开关量输出x2 （开关量就是开关的意思，有常开和常闭，中间公共端。
温度测量和人脸识别智能面板终端说明书
User ManualBody Temperature Measurement+Face RecognitionIntelligent Panel TerminalModel:FFT-02V1.1305503000481Table of Contents1Product introduction (3)1.1Product description (3)1.2Product appearance (3)1.3Definition of equipment interface (4)1.4Packing Contents (4)2Equipment installation (5)2.1Hardware Installation (5)2.2Installation location (10)2.3Installation environment (10)2.4Wiegand interface use (11)3Quick instructions (14)3.1Equipment connection (14)3.2Smart access control management software (19)4Program upgrade (30)1Product introduction1.1Product descriptionThe product of1080P temperature measurement&face recognition intelligent panel terminal is with LCD display screen.The product is an AI intelligent access control product,which embedding algorithm of deep learning face recognition,integrating the high-precision thermal imaging temperature measurement chip as well as ISP image processing.The product is equipped with powerful functions such as face detection,mask detection,face recognition comparison,body temperature detection and living body judgment.It's able to accurately capture the information(such as facial information,identity information,whether to wear a mask, etc.)and the body surface temperature of the person,who has passed through the camera's view.It is able to effectively help the users to manage access authority and monitor body temperature status,which is helpful to prevent the ers can manage access rights offline by loading the face library to the device,as well as matching with attendance software to achieve employee attendance management.The products can be widely applied in scenes such as community access,barrier gate and passage,office building and so on!1.2Product appearance1.3Definition of equipmentinterface No.Interface name Interface description 1Power interface 12VDC 2Network interface RJ45network interface 3Relay interface +:NO Normally open port-:COM Common end4Wiegand interface1:12VDC2:Wiegand protocol data portD13:Wiegand protocol data portD04:Signal ground 1.4Packing Contents●Panel Terminal ×1●Power Adapter ×1●Wall bracket ×1●Wiegand male socket×1●Expansion Screws×1●User Manual×12Equipment installation2.1Hardware InstallationThere are two ways to install this Panel Terminal.You can install it on the gate or on the wall.2.1.1The first wayYou can put the gate bracket directly on the gate interface.2.1.2The second wayIf you don ’t need the gate bracket,you can remove the bracket.1.Unscrew the bracket Acounterclockwise2.Take the tail wire out of the bracket,as shown in the figure below.Unscrew the bracket AA1233.After taking out bracket A,use a screwdriver to loosen the screws on both sides of bracket Bcounterclockwise4.Pull out the interface wires one byone.Note:Here must be pulled out one by one.546Be a screwdriver to unscrew the 4screws on bracket C,and then pull out the interface cables one by one as in step4.6.Screw the mount on the wall with the four screws provided.Note :The direction inside the redbox.7.Secure the mounting bracket to the back of the tablet with the four screwsprovided.8.Then use 2screws to screw on the side screw holes,as shown belowC9.Hang the bracket on the back of the machine on the bracket fixed on the wall,as shown below.10.Finally,use a screwdriver to tighten the side screws to prevent falling.2.2Installation locationThe camera shall be set in front of the channel to capture the face1.The camera shall be set in front of the channel to capture the face.2.It is suggested that the height h is about1.4~1.6meters,and the top view angle of the camera is0~5. degrees.3.In order to ensure the effect of temperature detection,it is better to keep the equipment0.4m away from the personnel collection point(with the range of0.3~0.5m),and the face pixels are not less than100pixels.2.3Installation environment1.Requirements for illumination:no backlight,no obvious reflection on the face,uniform light and no shadow.In addition,in order to ensure that the scene lighting is sufficient during face capturing,it is suggested that if the face in the lens image is not bright enough,lighting equipment should be added accordingly tosupplement the light on the face of the personnel(generally up to250-800Lux).2.Requirements for light and wind:recommend to install the equipment indoors,ensure that there is no wind or direct sunlight between the equipment and personnel,and to avoid too low or too high temperature measurement caused by blowing heat and direct sunlight.2.4Wiegand interface use2.4.1Wiegand output2.4.1.1Process introductionReady to work Operating proceduresFace libraryBinding card numberin face databaseFace comparison resultQuery face database CorrespondingCardIDWiegand interface output Card IDEndConfigure associationRelay outputConfigure Wiegand protocol parametersN2.4.1.2Wiring diagramConnect D0,D1and GND of the Wiegand interface to the Wiegand input interface of the access control board in order.2.4.1.3StepsStep 1:Add the face database,bind the Wiegand card number Card ID,as shown in the figure 12345678,click Confirm;No.Interface name Interface description1Power interface 12VDC2Network interface RJ45network interface 3Relay interface+:NO Normally open port -:COM Common end 4Wiegand interface1:12VDC2:Wiegand protocol data port D13:Wiegand protocol data port D04:Signal groundStep2:Configure the interface,turn on the Black/White list comparison switch and Face Recognition+ Relay;Step3:WEB web page configuration Wiegand output:Enter the IP address of the device in the IE browser to log in,enter the Settings—Network—WIEGAND interface,and configure according to the parameters of the Wiegand control panelMODE：26-bit or34-bit；Card Number：DET or HETStep4:Align the face with the device identification frame,and after the comparison is successful,the Wiegand interface outputs the signal to the control board.3Quick instructions3.1Equipment connectionThe equipment can be connected to the PC through the network cable.After the equipment is powered on, Download the“Access Control Software for FFT-02/Access_control_software”from /tools to your computer,open the smart access control management software,input user name and password to login.The default username and password is admin/123456,You can click the Change Password button to modify the password.NOTES:Access_control_software only supports Windows system.Factory equipment default IP address is192.168.1.18,your computer IP address needs to be on the same network segment as the equipment.How to modify the IP address of a windows computer?If your computer is directly connected to the network cable,not through the router,the setting method is as follows:1.Right-click the network icon on the computer desktop and select"Properties",enter to Network and sharing center,then click"Local Area Connection"2.After entering the Local Area Connection Status interface,click"Properties",enter to Local Area Connection Properties interface,then Double click"Internet Protocol Version4(TCP/IPv4)"3.Enter to Internet Protocol Version4(TCP/IPv4)Properties interface,select"Use the following IP address" You can enter the IP address as192.168.1.(2~254),Except192.168.1.18,click"OK"to take effect.If your computer is connected to the router through the network and then connected to your computer by therouter,the setting method is as follows:1.You can enter192.168.1.1in IE browser to enter your router settings page,if it is not192.168.1.1,please check the management account information marked on your router,You must set the IP address to192.168.1.(1~254),Except192.168.1.18,click"OK"to take effect.2.Right-click the network icon on the computer desktop and select"Properties",enter to Network and sharing center,then click"Local Area Connection"3.After entering the Local Area Connection Status interface,click"Properties",enter to Local Area Connection Properties interface,then Double click"Internet Protocol Version4(TCP/IPv4)"4.Enter to Internet Protocol Version4(TCP/IPv4)Properties interface,select"Obtain an IP address automatically"and"Obtain DNS server address automatically",click"OK"to take effect.3.2Smart access control management softwareAfter the device is powered on,the smart access control management software can be employed to set up a face library,preview real-time video,display real-time comparison results,read device logs,and configure device parameters.etc.3.2.1Introduction to main interfaceVideo preview window:After the device is connected,play the real-time video of the camera .IP input bar:The IP address of the device can be input here.Button for connecting /disconnecting device:Click [connect device]to connect to the device,it can be used to view real-time video,upload real-time snapshot pictures,display the recognition results,etc.Click [disconnect device]to disconnect and close preview.Comparison result:When the captured face matches with the face library in the device,it will be displayedhere.The basic information,similarity,temperature and other information of the face will be displayed,if the face library is not matched,it will not be displayed.Display bar of capture:In the mode of video preview,it can be used to display the captured face picturesand body surface temperature under the current screen.Video preview windowReal-time mode Face management Log view Visitor logsParameter configurationReserve buttonDisplay bar of captureIP input barComparison resultConnecting /disconnecting deviceFace management:Click to enter the face library management interface,it can be used to perform operations such as adding,subtracting,deleting,checking,and modifying the face librarLog View:View and export the face recognition record information saved by the device,and generate the personnel attendance record table.Parameter configuration:The interface of key parameter configuration of face recognition of the device, parameters are able to be modified on this interface.Reservation button:No function is defined yet,software setting function will be added later.3.2.2Face database managementUsers are able to perform operations such as adding,subtracting,deleting,checking,and modifying the face library in this interface.Previous Page/Next Page:Previous/Next page switching buttonGo to:Enter the specified page,click jump to quickly enter the corresponding pageAdd:Snap to add face library to the deviceDelete All:Click the button to delete all face libraries in the deviceImport One:Import one single picture to the device face libraryBulk Import:Batch import multiple pictures to the device face libraryExport picture:Export and backup the face library saved in the local software as a pictureSync face info:Click to automatically upload the basic information of the device’s face library personnel, such as the name,number,gender,age,etc.Sync face picture:The device uploads the face library to the PC softwareExport face data:Export and backup photos of face library which was saved locallyImport face data:Export and backup the information of the face library moved out to be backed up Modify:Modify the personal information of the current faceDelete:Delete the current face library information from the device3.2.2.1AddClick the Add button to enter the interface→the face is facing the camera→click the Snap button,capture the face picture→enter the personnel information,and click the Confirm button→the official face entry is successfully completed.3.2.2.2Import one face libraryClick I mport one,the face input interface will be popped up→click PIC,select the face image file→enter the person information→click confirm to enter to complete the single face import.3.2.2.3Bulk import face library operationClick Bulk Import,the interface pops up→click Select File,select the face picture folder→click Start Importing,and the import progress bar is completed to complete the batch import face operation.Note:The user are able to save the personnel information in the name according to the rules,import the picture name in batches will import the personnel information into the device synchronously.3.2.2.4Operation of Export pictureClick the Export picture button→select the picture naming rules in the pop-up box→select the directory and click the start export button to perform the export action→after the export is completed,a folder named by date will be generated.3.2.2.5Sync face infoClick the Sync face info button to synchronize the basic information of the face library,after synchronizing the basic information of the face library,you can view the face information on the page.3.2.2.6Synchronous face pictureUpload the face library in the device to the management software.After replacing a new device,the face libraryhas to be manually synchronized first,otherwise,the personnel information on the management software and the device's face library may be inconsistent,which may result in incorrect display of the identification and comparison information.3.2.3Log viewing&attendance recordClick button to enter the interface→select the search start and end time→click button to search thelog.Export attendance record:Click button→select save path→automatically export attendance record to save EXCEL.3.2.4Visitor logsClick button enter to the interface→select the search start and end time→click button to search the log.Click the Export visitor record button→select the save path→automatically export the attendance record to save EXCEL.3.2.5Parameter configurationUsers can set the key parameters of the face capture and device switch functions.The device supports the three major functions of face recognition comparison,body temperature detection,and mask ers are able to freely configure the switch function,whether or not to associate with control relay,and whether or not to broadcast voice reminders,etc.For example,if the user requires the door can be opened when the body temperature is normal,to realize this,the body temperature detection function needs to be turned on and the rest closed;if the user requires the door can be opened when the specified person,those with normal body temperature and are wearing mask,the face recognition comparison,body temperature detection,and mask detection need to be enabled at the same time,and when all three of these tests are normal,the relay will be controlled to open the door.The configuration interface and specific details are as follows.Snap Interval:set the face capture time interval to avoid repeated capture of pictures in a short time.Face Anti-Spoofing Paramete r:Set the Face Anti-Spoofing Parameter,0-1,the larger the value,the stricter the living body detection and the safer it is.Snap Picture Quality Parameters:Set the Snap Picture Quality Parameters,0is the worst,1is the best. Face Recognition Parameter:Set the Face Recognition Parameter,compare the captured face pictures with the face library,if the similarity exceeds this threshold,it would be recognized as the same person.The threshold is recommended to be set above70,the greater the matching similarity,the higher the requirement and the safer it isSnap Picture Blur Parameter:Set the Snap Picture Blur Parameter,range0-1,the smaller the value,the clearerSame Person Identified Time:Set the Same Person Identified Time,if it exceeds the number of times,there will no longer be any recognition,only by exiting the camera's field of view and re-entering the screen can it be continued to recognition.Recognition distance parameter:0.5m,1m,1.5m,2m,2.5m are optionally to be configured.The default is1 meter.Since the distance limit of the temperature measurement module is within1meter,this option is limitedand cannot be set.Face exposure parameter(0-100):Set the brightness of the captured picture of the face,the default is50. Software version:the factory default configuration version number is displayed for no revise. Temperature compensation setting:In the case of harsh environment,increase the compensation temperature to improve the accuracy of temperature measurementNormal Temperature t parameter:Set the temperature alarm temperature value,if it is higher than the set value,abnormal body temperature will be warned,if it is lower than the set value,the body temperature is normal.switch delay time:The pulse time(unit100ms)of the switch output,the default configuration is2or200ms. Black/white list comparison switch:Turn on and off the face recognition comparison function,if it is off,the face comparison will not be performed.Face Recognition+Relay:Switching the face recognition result associated relay action,after turning on,if face comparison is successful,and switched to the white list,the relay will be controlled to close.Face recognition voice prompt:Configure the voice broadcast mode of the recognition result,including three modes:on,off and on only for abnormal.On:When the comparison result is a white list,“please pass through”will be broadcast in voice,if the comparison result is not in the list library,u,then the voice broadcast will not be recognized;Off:no comparison and identification results will be broadcast;Temperature Detection On/Off:turn on and off the temperature detection function.Temperature-Detection+Relay:Configure whether to associate the relay.Configure to be related,if the body temperature is normal,the relay is controlled to open and close,and the default control relay mode is closed.Temperature detection voice prompt:Configure the temperature test result voice broadcast mode to:Off, Only for abnormal and TEMP vice prompt.Only for abnormal:If the temperature measurement value is higher than the high temperature threshold, "abnormal body temperature"will be voice broadcast,and the temperature is not broadcast when normal;Off:Broadcast no temperature measurement results;TEMP vice prompt:Broadcast the measured temperature value,if it is higher than the high temperature threshold,broadcast"temperature xx℃,abnormal body temperature"Mask detection On/Off:Turn on and off the mask detection function.Mask detection mode:It can be configured as two modes:the epidemic mode and the non-epidemic mode. Epidemic mode:In this mode,the voice will prompt"Please wear a mask"when detecting a mask is not worn; Non-epidemic mode:In this mode,when a person is detected wearing a mask,the voice will prompt"Please remove the mask"to improve the recognition accuracy.Mask-+relay:Turn on and off the mask-associated relay.In epidemic mode,when the mask is worn correctly, the relay is controlled to operate,otherwise the relay is not controlled.Mask detection voice prompt:Configure the mask reminder broadcast mode to only for abnormal,Off.Only for abnormal:in epidemic mode,"please wear a mask"will be broadcast if a mask is not worn, otherwise no reminder will be broadcast;in Off mode,"please remove the mask"will be broadcast if a mask is worn,otherwise there will be no broadcast.Overlay time:When it selects stacking time,the device's current time is displayed on the screen,and when it is No stack,the device's time is not displayed on the screen.Temperature format:Configure the temperature unit.It can be configured as two temperature units of Celsius and Fahrenheit.Relay On/Off State:There are two modes:Normal and AbnormalTemperature measuring mode:There are two modes:Indoor and outdoor,you can choose according to your installation environmentIO output mode:There are two modes:Wiegand output and lamp control output,you can choose according to your needs modes.Face recognition mode:There are three modes:Local recognition,Local and online recognition and Online recognitionRefresh:Click the button to get the configuration on the device.Save configuration:Click the button to send the configuration information to the device to save and take effect.4Program upgradeNote:Only support IE browse.Step1:Open the browser,input the equipment IP address,and input the user name(default:admin)and password(default:blank)Step2:Click Settings->System->Maintenance in sequence to enter the upgrade interface.Step3:Click browse to select the app.ifu upgrade package.Step4:Click the[Upload]button to start the upgrade.Wait for the upgrade to complete and the web page will automatically refresh.12345CE Certificate statement Website:https:///company/ce-certificate.htmlExporter and Importer Information Opened to Public:https:///company/open-information.htmlManufacturer:Shenzhen Foscam Intelligent Technology Co.,LtdAddr:Room901,Unit B,Building7,Xingke1st Street Vanke Cloud City Phase1, Nanshan Dist.,Shenzhen,518055,China31。
人脸识别系统快速操作手册
人脸识别系统快速操作手册目录1 摄像机安装及注意事项........................................................................... .. (3)摄像机选型........................................................................ (3)安装位置选择........................................................................ (3)镜头选择........................................................................ (4)2 智能服务器安装指南........................................................................... (6)服务器硬件安装........................................................................ (6)人脸比对系统安装说明........................................................................ (7)比对服务器和检索服务器的安装................................................................... (7)mysql 数据库安装 (7)人脸比对系统卸载........................................................................ (8)服务器软件卸载................................................................... (8)mysql 数据库卸载 (8)3 人脸分析管理软件安装指南........................................................................... (8)客户端软件的安装........................................................................ (8)客户端软件的卸载........................................................................ (8)4 客户端软件配置........................................................................... .. (9)登录客户端........................................................................ (9)添加设备........................................................................ (9)添加抓拍机................................................................... (9)添加服务器................................................................... (10)配置监控点........................................................................ (11)抓拍机智能配置................................................................... (12)人脸曝光功能设置................................................................... (14)人脸比对服务器设置................................................................... (14)人脸检索服务器配置：................................................................. (17)5 系统配置........................................................................... (20)报警设置........................................................................ (20)本地设置........................................................................ (21)抓拍机相关........................................................................ (22)抓拍图片保存设置........................................................................ (22)6 常见问题及解答........................................................................... (24)1 摄像机安装及注意事项摄像机选型摄像机一般选用百万高清摄像机。
测温人脸识别终端 快速入门指南说明书
测温人脸识别终端快速入门指南UD19284B-D外接门磁和开门按钮时，需要与RS-485或者电源共地。
接线（无门控安全模块）版权所有©杭州海康威视数字技术股份有限公司2021。
保留一切权利。
本手册的任何部分，包括文字、图片、图形等均归属于杭州海康威视数字技术股份有限公司或其子公司（以下简称“本公司”或“海康威视”）。
未经书面许可，任何单位和个人不得以任何方式摘录、复制、翻译、修改本手册的全部或部分。
除非另有约定，本公司不对本手册提供任何明示或默示的声明或保证。
关于本产品本手册描述的产品仅供中国大陆地区销售和使用。
本产品只能在购买地所在国家或地区享受售后服务及维保方案。
关于本手册本手册仅作为相关产品的指导说明，可能与实际产品存在差异，请以实物为准。
因产品版本升级或其他需要，海康威视可能对本手册进行更新，如您需要最新版手册，请您登录海康威视官网查阅（）。
海康威视建议您在专业人员的指导下使用本手册。
• 为海康威视的注册商标。
• 本手册涉及的其他商标由其所有人各自拥有。
责任声明• 在法律允许的最大范围内，本手册以及所描述的产品（包含其硬件、软件、固件等）均“按照现状”提供，可能存在瑕疵或错误。
海康威视不提供任何形式的明示或默示保证，包括但不限于适销性、质量满意度、适合特定目的等保证；亦不对使用本手册或使用海康威视产品导致的任何特殊、附带、偶然或间接的损害进行赔偿，包括但不限于商业利润损失、系统故障、数据或文档丢失产生的损失。
• 您知悉互联网的开放性特点，您将产品接入互联网可能存在网络攻击、黑客攻击、病毒感染等风险，海康威视不对因此造成的产品工作异常、信息泄露等问题承担责任，但海康威视将及时为您提供产品相关技术支持。
• 使用本产品时，请您严格遵循适用的法律法规，避免侵犯第三方权利，包括但不限于公开权、知识产权、数据权利或其他隐私权。
您亦不得将本产品用于大规模杀伤性武器、生化武器、核爆炸或任何不安全的核能利用或侵犯人权的用途。