汽车专业英语词汇[修正版]
汽车英语专业词汇(完全篇)
底盘平移台chassis shuttle车辆转移台bus transfer前围角板front wall angle cover后围侧板rear wall side cover保险杠bumper三类底盘three type chassis左侧围应力蒙皮R/S stretching skin (road side)中涂floating coat拼装台collector切割轮口wheel -arch cutting内饰trim线束harness返工re-doing轮罩护板wheel house发车前准备pre-delivery举升hoist小批量产品be pilot2 套two kits配电站power transformer substation裙板skirt发动机托架engine holding frame诊断报警系统diagnosis and alarming system互换性interchangeability缩微图纸microfiche files总装final assembly磷化phosphate仪表板dash board切齐trimming结构完整性structure integrity自动愈合的防腐材料self-healing corrosion preventative material 长途客车inter-city bus改装厂refitting factory遮阳板sun visor随车工具tool box钢化玻璃toughened grass异形钢管special steel pipe全天候空调系统full range A/C强制通风ram-air ventilation停机时间downtime无公害柴油clean diesel宽敞悬臂式座椅roomy cantilevered seat防滑地板no-skid floor织物纹里铝合金textured aluminum extrusion爬坡能力grade ability排水阀drain valve除湿器moisture ejector怠速时at idle琴式驱动桥banjo type drive axle通风口duct恒温控制thermostatic control平衡水箱surge tank变光开关simmer switch消音器muffler防破坏vandal resistant聚碳化透镜poly-carbonate Len镀锌板galvanized plate搭接lap亮丽的外表smart appearance隐藏式固定concealed fastening水洼pending发动机中置式客车bus with under floor engine组合式客车车身modular bus body薄壳式结构shell construction衬垫pad空气导流板air deflector搁梁shelf beam腰梁waist rail梭梁stabilizing beam腰带式安全带diagonal safety belt压条trim strip嵌条insertion strip翼板fender斜撑bracing piece转向盘回正性试验test of steering wheel return ability转向盘转角脉冲试验steering wheel impulse input test转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test极限侧向加速度试验limiting lateral acceleration test汽车平顺性随机输入行驶试验automobile ride random input running test汽车平顺性单脉冲输入行驶试验automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验measurement of natural frequency and damping ratio of suspension功率突然变化影响试验test of effect of sudden power change收油门后控制试验test of control at breakaway横风稳定性试验test of crosswind stability反冲试验kick-back test轮胎爆破响应时间试验test of burst response of tire绕过障碍物试验obstacle avoidance test移线试验lane change testJ型转弯试验test of J turn频率响应时间试验frequency response test瞬态响应时间试验transient response test阶路响应时间试验step response test脉冲响应试验pulse response test静态操舵力试验static steering effort test悬架举升试验jack-up test of suspension耐翻倾试验test of overturning immunity轮辋错动试验rim slip test风洞试验wind tunnel test制动稳定性试验test of braking stability最小转弯直径试验minimum turning diameter test操舵力试验steering effort test类型type发动机engine内燃机internal combustion engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engine油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engine直列式发动机in-line engine星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机w-engineI形发动机I-engineL形发动机L-engineF形发动机F-engine性能performance二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle工作循环working cycle等压循环constant pressure cycle理想循环ideal cycle热力循环thermodynamic cycle冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging stroke压缩行程compression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke换气压缩行程exchange-compression stroke止点dead center上止点top dead center(upper dead center)下止点lower dead center(bottom dead center)上止点前budc(before upper dead center)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom dead center)下止点后abdc(after bottom dead center)缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept volume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression ratio临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effective pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时，马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effective thermal efficiency充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean piston speed发动机转速engine speed (rotational frequency)怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode)额定工况declared working condition变工况variable working condition稳定工况steady working condition空载no-load全负荷full load超负荷overload部分负荷part load充量（进气）charge旋转方向direction of rotation顺时针clockwise逆时针counter-clockwise左转left-hand rotation右转right-hand rotation外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance加载性能loading performance起动性能starting performance加速性能acceleration performance动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics万有特性mapping characteristics稳定调速率steady state speed governing rate 气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock)发动机罩engine bonnet气缸体加强筋engine block stiffening rib气缸cylinder（转子机）缸体stator缸径cylinder bore气缸体机架cylinder block frame气缸盖cylinder head配气机构箱valve mechanism casing气缸体隔片cylinder spacer气缸盖密封环cylinder head ring gasket气缸盖垫片cylinder head gasket气缸套cylinder liner(cylinder sleeve)干式缸套dry cylinder liner湿式缸套wet cylinder liner气缸水套water jacket膨胀塞expansion plug防冻塞freeze plug气缸壁cylinder wall环脊ring ridge排气口exhaust port中间隔板intermediate bottum导板guideway创成半径（转子机）generating radius缸体宽度（转子机）operating width机柱column燃烧室combustion chamber主燃烧室main combustion chamber副燃烧室subsidiary combustion chamber预燃室prechamber涡流燃烧室swirl combustion chamber分开式燃烧室divided combustion chamber涡流式燃烧室turbulence combustion chamber半球形燃烧室hemispherical combustion chamber浴盆形燃烧室bathtub section combustion chamberL形燃烧室L-combustion chamber楔形燃烧室wedge-section combustion chamber开式燃烧室open combustion chamber封闭喷射室closed spray chamber活塞顶内燃烧室piston chamber爆发室explosion chamber燃烧室容积比volume ratio of combustion cahmber燃烧室口径比surface-volume ratio of combustion chamber 通道面积比area ratio of combustion chamber passage曲轴箱通气口crankcase breather凸轮轴轴承座camshaft bearing bush seat定时齿轮室罩camshaft drive(gear)cover曲轴箱检查孔盖crankcase door曲轴箱防爆门crankcase explosion proof door主轴承盖main bearing cap气缸盖罩valve mechanism cover飞轮壳flywheel cover扫气储器scavenging air receiver活塞piston裙部开槽活塞split skirt pistonU形槽活塞U-slot piston滚花修复活塞knurled piston圆顶活塞dome head piston平顶活塞flat head piston凸顶活塞crown head piston(convex head piston)凹顶活塞concave head piston阶梯顶活塞step-head piston筒形活塞trunk piston椭圆形活塞oval piston抗热变形活塞autothermic piston不变间隙活塞constant clearance piston镶因瓦钢片活塞invar strut piston直接冷却式活塞direct-cooled piston间接冷却式活塞indirect cooled piston滑裙活塞slipper piston活塞速度piston speed活塞顶部piston head活塞裙部piston skirt整体活塞裙solid skirt活塞裙扩大衬簧piston skirt expander滑履式活塞裙slipper skirt隔热槽heat dam活塞标记piston mark活塞销piston pin活塞销孔piston pin boss活塞销衬套piston pin bushing全浮式活塞销full-floating piston pin半浮式活塞销semifloating piston pin固定螺钉式活塞销set screw piston pin活塞环piston ring组合式活塞环compound piston ring同心活塞环concentric piston ring偏心活塞环eccentric piston ring自由环free ring闭合环closed ring梯形环keystone ring半梯形环half keystone ring矩形环rectangular ring油环oil control ring开槽油环slotted oil control ring螺旋弹簧加载双坡口油环coil spring loaded slotted oil control ring 涨环expander双坡口油环double bevelled oil control ring内上坡口internal bevel top内下坡口internal bevel bottom边缘坡口油环bevelled-ege oil control ring刮油环scrapper ring钩形环napier ring镀铬活塞环chrome plated piston ring活塞衬环piston ring expander活塞环槽piston ring groove活塞环区ring zone活塞环岸piston ring land活塞环内表面back of ring曲柄连杆机构connecting rod中心曲柄连杆机构central-located connecting rod 偏心曲柄连杆机构offset connecting rod铰接曲柄边杆机构hinged connecting rod连杆connecting rod连杆小头connecting rod small end连杆大头connnecting rod big end连杆杆身connecting rod shank副连杆slave connecting rod叉形连杆fork-and-blade connecting rod主连杆main connecting rod方形连杆boxed rod绞链式连杆hinged type connecting rod活节式连杆articulated connecting rod连杆盖connecting rod cap连杆轴承connecting rod bearing曲轴crankshaft整体式曲轴one-piece crankshaft组合式曲轴assembled crankshaft右侧曲轴right-hand crankshaft左侧曲轴left-hand crankshaft改变行程的曲轴stroked crankshaft曲轴前端crankshaft front end曲轴主轴颈crankshaft main journal轴颈重叠度shaft journal overlap圆角fillet主轴承main bearing曲轴止推轴承crankshaft thrust bearing薄臂轴瓦thin wall bearing shell曲轴油道crankshaft oil passage曲柄crank曲柄臂crank arm曲柄销crank pin轴套bush曲柄转角crank angle曲柄半径crank radius抛油圈oil slander角度轮degree wheel动平衡机dynamic balancer平衡重balancer weight扭振减振器torshional vibration damper扭振平衡器torsion balancer谐振平衡器harmonic balancer振动平衡器vibration balancer曲轴链轮crankshaft sprocket转子轴颈rotor journal偏心轴eccentric shaft曲轴箱crankcase闭式曲轴箱通风装置closed-crankcase ventilating system 飞轮flywheel飞轮齿圈flywheel ring gear飞轮芯棒cantilever飞轮芯轴flywheel spindle飞轮的惯量矩flywheel moment of inertia飞轮标记flywheel mark当量系统equivalent system当量轴长equivalent shaft length一级往复惯性力reciprocating inertia force,1st order二级往复贯性力reciprocating inertia force, 2nd order离心惯性力centrifugal inertia force配气机构valve gear凸轮轴camshaft凸轮cam整体式凸轮轴one-piece camshaft组合式凸轮轴assembled camshaft凸轮轴驱动机构camshaft drive赛车用凸轮轴race camshaft凸轮轴轴颈camshaft bearing journal凸轮轴轴承camshaft bearing凸轮轴偏心轮camshaft eccentric凸轮轴链轮camshaft sprocket凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮camshaft gear wheel进口凸轮inlet cam排气凸轮exhaust cam快升凸轮quick lift cam快升缓降凸轮quick lift gradual clsing cam凸轮轮廓cam contour凸轮包角cam angle凸轮升程cam-lobe lift凸轮尖cam nose凸轮从动件cam follower齿轮传动机构gear drive正时齿轮timing gear链传动机构chain drive链轮sprocket wheel链轮盘chain sprocket正时链条timing chain带齿皮带toothed timing belt链条张紧轮chain tension gear半速齿轮half speed gear正时齿轮刻印记号timing gear punch mark气门valve进气过程intake process换气过程gas exchange process扫气过程scavenging process给气比delivery ratio分层充气stratified charge充量系数volumetric efficiency涡流比swirl rate进气涡流intake swirl螺旋进气道进气helical duct intake导流屏式气门进气masked valve intake切向进气道进气tangential duct intake进气紊流intake trubulence进气提前角intake advance angle进气持续角intake duration angle进气迟后角intake lag angle进面值time-area value气门升程valve lift气门正时valve timing扫气口面积scavenging port area菌形气门mashroom valve, poppet valve钠冷却气门sodium filled valve(natrium cooled valve) 双气门dual valve进气门intake valve (suction valve,inlet valve)排气门exhaust valve顶置气门overhead valve侧置气门side valve倾斜气门inclined overhead valve直立气门vertical overhead valve套筒式滑阀sleeve valve气门机构valve gear直接式气门驱动机构direct valve gear间接式气门驱动机构indirect valve gear气门杆valve stem加大气门杆oversize valve stem气门头valve head气门工作面valve face气门边限valve margin气门弹簧座valve-spring retainer气门锁片valve key气门间隙调节螺钉valve lash adjusting screw气门旋转器valve rotator气门室valve cage气门油封valve oil seal气门口valve port气门座valve seat气门座镶圈（嵌镶式气门座圈）valve seat insert(valve seat ring) 气门座锥角valve seat angle气门座宽度valve seat width气门挺杆valve tappet(valve lifter)液力挺杆hydraulic tappet(lifter)无间隙挺杆zero-rush tappet (non-clearance tappet)筒形挺杆barrel type tappet油压挺杆ooil tappet滚轮挺杆roller tappet(lifter)挺杆转位tappet rotation排气门挺杆exhaust valve lifter气门导管valve guide气门杆导管stem guide气门重叠度stem overlap气门开启持续时间valve duration气门正时标记valve timing sign气门弹簧valve spring气门内弹簧inner valve spring气门外弹簧outer valve spring刚性缓冲弹簧stiff buffer spring上紧弹簧energizing spring防振气门弹簧non-surging spring弹簧座圈spring retainer蝶形弹簧belleville spring滚柱roller气门室盖valve chamber cover摇臂rocker arm高升程摇臂high lift rocker arm摇臂轴rocker arm shaft推杆push-rod摇臂支架rocker arm bracket气门摇臂室罩valve rocker chamber cover导向轮guide wheel导杆slide bar导轨slide rail张紧轮tensioning wheel链条张紧调节装置assembly chain tension adjuster张紧带轮tensioning pulley传动带张紧装置belt tensioner同步驱动皮带synchronous belt同步驱动皮轮synchronous belt pulley供油系fuel system控制燃烧系统controlled combustion system反湿气装置antipercolator电子燃油喷射electronic fuel injection蒸气回收装置vapor recovery system燃油蒸气回收系统fuel vapor recovery system液体回收装置liquid withdrawal system恒量净化管constant purge line碳罐净化管canister purge line供油量fuel delivery循环供油量fuel delivery per cycle额定供油量rated fuel delivery怠速供油量idling speed fuel delivery供油规律fuel supply rate curve油量调节装置fuel control unit供油提前角fuel supply advance angle进油计量inlet metering几何供油行程geometric fuel delivery stroke供油率fuel supply rate燃油通道fuel gallery有效行程effective stroke剩余行程remainder stroke变行程计量variable stroke metering等容卸载constant volume unloading变容卸载variable volume unloading收缩容积retraction volume燃油喷油装置fuel injection equipment燃油喷射泵fuel injection pump滚轮式燃油喷射泵roll fuel injection pump凸轮轴式燃油喷射泵camshaft fuel injection pump直列式燃油喷射泵in-line fuel injection pump伺服式燃油喷射泵servo fuel injection pump底部突缘安装燃油喷射泵base flanged mounted fuel injection pump 上部安装燃油喷射泵high flanged-mounted fuel injection pump侧向安装燃油喷射泵side-mounted fuel injection pump端部突缘安装式燃油喷射泵end flange-mounted fuel injection pump V形燃油喷射泵vee fuel injection pump脉动式燃油喷射泵jerk fuel injection pump螺纹安装燃油喷射泵screw-mounted fuel injection pump蓄能式燃油喷射泵accumulator fuel injection pump往复式燃油喷射泵reciprocating fuel injection pump驱动轴式燃油喷射泵driveshaft fuel injection pump单缸式燃油喷射泵single cylinder fuel injection pump圆柱式燃油喷射泵cylindrical fuel injection pump旋转式燃油喷射泵rotary fuel injection pump分配式燃油喷射泵distributor fuel injection pump多缸燃油喷射泵multicylinder fuel injection pump框架安装式燃油喷射泵cradle mounted injection pump喷油始点fuel injection beginning喷油终点fuel injection end喷油持续角fuel injection duration angle喷油延迟injection delay引燃喷射pilot injection启喷压力injection starting pressure峰值喷油扭矩peak injection torque峰值喷油压力peak injection pressure喷油泵油缸数目number of cylinders of an injection pump无气喷射solid injection喷射正时injection timing集中喷射group injection喷油器injector整体式喷油器unit injector喷嘴nozzle轴针式喷嘴pintle type nozzle环槽式喷嘴annular slot nozzle孔式喷嘴hole type nozzle长杆喷嘴long stem nozzle孔板式喷嘴orifice plate nozzle开式喷嘴open nozzle闭式喷嘴closed nozzle喷油提前器timing advance unit喷射泵壳体injection pump housing针阀needle芯轴central spindle喷嘴壳体nozzle body针阀升程needle lift喷嘴盖形螺母nozzle cap nut喷油器壳体nozzle holder突缘安装喷油器壳体flanged-mounted injection nozzle holder 燃油喷射泵传动装置transmision of an injection pump喷嘴锥体nozzle hole cone柱塞plunger柱塞套barrel柱塞行程plunger stroke喷孔spray orifice海拔控制器altitude control提前器飞锤flyweight喷孔长径比ratio of nozzle hole length nozzle diameter喷嘴液动力特性nozzle hydrokinetic characteristics动态相位dynamic phase喷孔面积nozzle hole area喷嘴流通特性nozzle flow characteristic喷油背压injection back pressure高压油管high pressure pipe平均喷油扭矩mean injection torque喷油总效率overall pumping efficiency峰值喷油压力injection peak pressure预行程prestroke收缩行程retraction stroke燃油箱fuel tank油箱盖fuel tank油位表fuel level gauge注油控制装置fill control system汽油箱gasoline tank( petrol tank)汽油供给管gasoline feed pipe加油管filler tube放油螺塞drain plug吸油管suction pipe刚性燃油管rigid fuel pipe进油孔fuel feed hole供油管supply pipe通气管bleeding pipe通气管bleeding pipe泄油阀spill valve泄油孔口spill port进油阀inlet valve最大油量限制器maximum fuel stop滴油dribble燃油表fuel gauge输油泵feed pump燃油泵fuel pump附装燃油箱中的电动燃油泵tank-mounted eletric fuel pump 机械式燃油泵mechanical fuel pump膜片式燃油泵diaphragm fuel supply pump叶片式供油泵vane fuel supply pump活塞式输油泵piston type fuel supply pump齿轮式输油泵gear fuel supply pump电动燃油泵eletric fuel pump带真空泵的汽油泵vacuum pump with fuel pump起动加油器primer起动给油杆primer lever燃油泵上体fuel pump body燃油泵下体fuel pump base燃油泵盖bowl cover进油口接头fuel inlet neck出油口接头fuel discharge port输出阀delivery valve泵油元件pump element回油阀部件fuel return valve assembly化油器carburetor化油器系统carburetor circuit简单化油器elementary carburetor单腔化油器single-barrel carburetor双腔并动化油器two-barrel dual carburetor双腔分动化油器two-barrel duplex carburetor四腔化油器four-barrel carburetor上吸式化油器updaught carburetor下吸式化油器downdraught carburetor平吸式化油器horizontal carburetor侧吸式化油器side-draft-carburetor高海拔补偿式化油器altitude compensating carburetor 化油器附加器adaptor carburetor双腔式化油器twin-choke carburetor固定喉管式化油器fixed venturi carburetor可变喉管化油器variable venturi carburetor化油器接头carburetor adaptor阻风门choke valve阻风活塞choke piston阻风板choke plate自动阻风门automatic choke阻风门拉钮choke button电控自动阻风门electric-assisted choke阻风管choke tube喉管venturi双重或三重喉管double & triple venturi阻风门拉线choke cable化油器小喉管booster venturi浮子系float system浮子float环形浮子annular float同心式浮子concentric float浮子支销float hinge pin浮子针阀float needle valve阀针valve needle浮子油面float level浮子臂float arm侧置浮子室式side float type怠速阀idle valve怠速针阀idle needle省油器economizer省油器阀economizer valve辅助空气阀auxiliary air-valve加速油井accelerating well加速泵accelerating pump加速泵喷嘴accelerating pump nozzle油门throttle手油门hand throttle节气门操纵手柄throttle control lever真空加浓器vacuum booster加浓器excess fuel device量孔体jet block怠速量孔idle metering jet主量孔main metering jet剂量阀活塞dosage valve piston空气量孔air jet燃油滤清器fuel filter沉淀杯sediment bowl串联过滤器in-line filter燃油箱内装过滤器in-tank filter调速器governor飞球式调速器flyball governor调速器governor飞球式调速器flyball governor液压调速器hydraulic governor真空转速调速器vacuum speed governor惯性调速器inertia governor离心调速器centrifugal governor调速器重锤governor weight空气滤清器及进排气系统air cleaner and intake and exhaust sytem 空气滤清器air filter冲压式空气滤清器ram air clearner恒温控制式空气滤清器thermostatic controlled air cleaner油浴式空气滤清器oil bath air cleaner纸质空气滤清器paper air clearner旋流管式空气滤清器swirl tube air filter滤清器滤芯filter element空气滤清器壳体air filter housing空气滤清器盖air filter cover滤清器密封圈filter seal ring滤网sieve滤纸盘或膜filter paper disc or membrane进气和排气系统intake and exhaust system排气管exhaust pipe排气抽气管exhaust extraction duct扫气泵scavenging pump进气预热装置intake preheater进气歧管intake manifold进气歧管真空度intake manifold vacuum冷式进气歧管cold manifold冲压式进气歧管ram intake manifold排气歧管exhaust manifold脉冲式排气歧管pulse exhaust manifold等压排气歧管constant pressrue exhaust manifold排气歧管热量控制阀exhaust manifold heat control valve超高度歧管high-rise manifold升温横跨管道heat crossover排气横跨管道exhaust crossover预热点hot spot阻风门加热器choke heater热空气导流管hot air duct隔热板heat shield排气再循环阀exhaust -gas-recirculation消声器silencer进气消声器intake silencer排气消声器exhaust silencer金属垫片式消声器steel pack muffler玻璃丝消声器glass pack muffler空洞消声器gutted muffler前排气管front exhaust pipe尾管tail pipe消声器联接管intermediate pipe热空气管hot air pipe曲轴箱通风管crankcase bleed pipe隔声罩acoustic hood进气消声器元件silencer element真空泵vacuum pump指示功率indicated power指示热效率indicated thermal efficiency指示油耗率indicated specific energy consumption示功图indicator diagram冷却系cooling system风冷air cooling水冷water-cooling循环流冷却系cooling recovery system自然循环液冷却系统natural circulation type cooling system热流循环液冷却系统thermo-siphon circulation type cooling system 温差循环液冷却系统gravity circulation water cooling system压力式水冷却系统positive circulation cooling system加压式冷却法pressure type cooling水泵循环冷却系统pump circulation cooling system强制循环式化冷系统forced-feed water circulation system 封闭式液冷系统sealed cooling system散热器radiator片式散热器finned radiator管式散热器tubular radiator蜂窝式散热器cellular radiator哈里逊式散热器Harrison type radiator带板式散热器ribbon type radiator上水箱upper tank下水箱lower tank涨溢箱expansion tank散热器芯radiator core之字形管散热器芯film core管-片式散热器芯fin and tube core散热器加水口盖radiator filter cap压力式水箱盖radiator-pressure cap蒸气-空气泄放阀vapor-air release valve散热器护罩radiator cowl散热器百叶窗radiator shutter散热器保温帘radiator roller blind散热片cooling fin缸盖散热片cylinder head fin缸体散热片cylinder block fin控温装置temperature regulating device恒温器thermostat恒温器主阀thermostat main valve恒温器旁通阀thermostat by-pass valve恒温器挠性波纹筒thermostat flexible bellows液体冷却设备liquid cooling equipment水泵water pump水泵体pump casing水泵叶轮water pump impeller旁通进水口water by-pass inlet neck循环泵circulating pump主进水口water main inlet port出水口water outlet port自调式水封self-adjusting seal unit溢流管overflow pipe导流板deflector风扇fan(blower)轴流式风扇axial flow fan离心式风扇centrifugal fan风扇壳体blower casing风扇导流罩fan cowl风扇毂fan hub风扇叶片fan blade风扇叶轮blower impeller风扇导流定子blower stator风扇皮带轮fan pulley三角皮带v-belt风扇护罩fan shroud风扇叶轮叶片impeller vane冷却用空气cooling air风扇导流叶片stator vane强制风冷forced-air cooling自然风冷natural air cooling风道air ducting润滑系lubrication system润滑lubrication气缸上部润滑upper cylinder lubrication 压力润滑pressure-feed lubrication压力润滑法forced lubrication自动润滑automatic lubrication飞溅润滑splash lubrication润滑周期lubrication interval边界润滑borderline lubrication曲轴箱机油油盘crankcase oil pan油底壳oil pan机油盘放油塞sump plug集油器oil collector机油泵oil pump计量式机油泵metering oil pump齿轮式机油泵gear type oil pump转子式机油泵rotor-type oil pump机油泵出油管oil pump outlet pipe放油口oil drain hole油道oil duct断油开关cut-off cock机油散热器oil cooler机油滤清器oil filter机油粗滤器primary oil filter机油精滤器secondary oil filter全流式机油滤清器full-flow oil filter分流式机油滤清器by-pass oil filter离心式机油滤清器centrifugal oil filter 整体式滤芯integral filtering element细滤器滤芯filter element滤清器壳filter box滤片filtering disc机油减压器oil pressure relief valve旁通阀by-pass oil filter机油滤网oil strainer加机油孔oil filter cap滤芯轴filter shaft刮片组件cleaning edge机油量尺dipstick机油滤网oil strainer增压器supercharger增压和扫气装置pressure-charging and scavenging unit 增压装置supercharging device涡轮增压器turbo-charger气波增压器comprex pressure wave supercharger增压器阻风阀supercharger blast gate增压器调节容气量的旁通阀supercharger control bypass 增压器叶轮supercharger impeller惯性增压inertia supercharging机械增压mechanical supercharging涡轮增压turbo-charging增压比supercharge ratio增压压力boost pressure增压中冷inter-cooling中冷度inter-cooling level增压度supercharging level喘振surge喘振线surge line轴流式涡轮axial-flow turbine脉冲进气ram charging发动机试验engine test发动机试验规程engine test procedure发动机技术要求engine technical requirements标准大气状况standard atmospheric conditions大气压力atmospheric pressure进气温度inlet air temperature进气温度inlet air temperature功率校正power correction功率标定power rating功率换算power conversion校正系数correction factor换算系数performance test性能试验performance test起动性能试验starting ability test怠速试验idle running test道路负荷试验road load test各缸工作均匀性试验cylinder variation test背压试验back pressure test最低稳定工作转速试验lowest continuous speed test with load 背部泄漏试验back-leakage test调整试验adjustment test热平衡试验heat balance test快速磨损试验accelerated wear test热冲击试验thermo-shock test空载特性试验no-load characteristic test模拟增压试验simulated supercharging test停缸试验cylinder fuel-cut test增压机匹配试验turbo-charger matching test排气分析试验exhaust analysis test突变负荷试验sudden load change test稳定性试验stability test单缸熄火试验one cylinder shut off test例行检查试验routine inspection test验证试验verification test鉴定试验approval test可靠性试验reliability test耐久性试验durability test定型试验type approval test验收试验acceptance test现场试验field test出厂试验delivery test抽查试验spot check test复查试验re-check test台架试验bench test强化试验hop-up test发动机试验台engine test bed底盘测功机chassis dynamometer测功机dynamometer水力测功机hydraulic dynamometer电涡流测功机eddy current dynamometer电力测功机electric dynamometer扭矩仪torque meter转速表tachometer温度测量thermometry温度测量仪器thermometric instruments空气流量测量air flow measurement热线风速仪hot wire anemometer电子示功仪electronic indicator燃烧分析仪combustion analyzer压力传感器pressure transducer精密声级计precision sound level meter排放emission排放物emission排气污染物gaseous pollutant蒸发排放物evaporative emission曲轴箱排放物crankcase emission漏气blowby gas氨氧化物oxids of nitrogen一气化碳carbon monoxide碳氢化合物hydrocarbon甲烷methane无甲烷碳氢化合物non-methane hydrocarbons光化学活性碳氢化合物photochemically reactive hydrocarbons 微粒物particulated matter黑烟black smoke蓝烟blue smoke白烟white smoke碳烟soot光化学烟雾smog臭味odor丙烷propane排放浓度concentration of emission排气烟度exhaust smoke先期排气initial exhaust亚临界排气subcritical exhaust超临界排气supercritical exhaust强制排气forced exhaust自由排气free exhaust排气提前角exhaust advance angle排气迟后角exhaust lag angle排气热损失exhaust heat loss排气净化exhaust purification排气背压exhaust back pressure残余废气residual gas排气有害成分poisonous exhaust composition柴油机排烟diesel smoke综合排放浓度composite concentration of exhaust emission综合排放质量composite mass of exhaust emission排放系数emission factor排放率emission index质量排放量mass emission比排放量brake specific emission排放物控制系统emission control system排气排放物控制系统exhaust emission control system二次空气secondary air二次空气分配歧管secondary air distribution二次空气控制阀secondary air control valve二次空气转换阀secondary air switching valve。
汽车专业英语词汇
汽车专业英语词汇汽车 automobile拖拉机 tractor铁路机车 locomotive有轨电车 tram无轨电车 trolley军用车辆 military vehicle蒸汽机 steam engine煤气机 gas engine汽油机 gasoline engine国民经济 national economy国内生产总值 (GDP) Gross Domestic Production 全拆散 (CKD) Completely Knock Down半拆散 (SKD) Semi-Knock Down改革开放 reform and opening技术引进 technical import国产化 localization支柱产业 pillar estate轿车 car客车 bus, coach货车 truck, lorry公路用车 road vehicle非公路用车 off-road vehicle发动机 engine机体 engine body曲柄连杆机构 crank-connecting rod mechanism 配气机构 valve timing mechanism供给系 fuel supply system冷却系 cooling system润滑系 lubricating system点火系 ignition system起动系 starting system底盘 chassis传动系 power train离合器 clutch变速器 gear box传动轴 propeller shaft驱动桥 drive axle行驶系 running gear车架 frame悬架 suspension前轴 front axle桥壳 axle housing车轮 wheel转向系 steering system转向盘 steering wheel转向器 steering gear转向传动装置 steering linkage助力装置 power assisting device制动系 braking system控制装置 control device供能装置 power supply device传动装置 transfer device制动器 brake车身 body车前板制件 front end panels车身壳体 body shell车门 door车窗 window附属装置 auxiliary device货箱 carrying platform发动机前置后轮驱动 (FR) front engine rear drive 发动机前置前轮驱动 (FF) front engine front drive 发动机后置后轮驱动 (RR) rear engine rear drive发动机中置后轮驱动 (MR) midship engine rear drive 全轮驱动 (AWD) all wheel drive驱动力 tractive force阻力 resistance滚动阻力 rolling resistance空气阻力 air resistance, drag上坡阻力 gradient resistance附着作用 adhesion附着力 adhesive force附着系数 coefficient of adhesion第一章发动机工作原理二冲程发动机 two stroke engine四冲程发动机 four stroke engine水冷发动机 water cooled engine风冷发动机 air cooled engine上止点 (UDP) upper dead point下止点 (LDP) lower dead point活塞行程 stroke汽缸直径 bore工作容积 working volume排量 swept volume, displacement进气行程 intake stroke压缩行程 compression stroke压缩比 compression ratio做功行程 working stroke爆燃，敲缸 detonation, knock 排气行程 exhaust stroke示功图 indicating diagram汽缸体 cylinder block汽缸盖 cylinder head油底壳 oil sump活塞 piston连杆 connecting rod曲轴 crankshaft飞轮 flywheel进气门 intake valve排气门 exhaust valve挺柱 tappet推杆 push rod摇臂 rocker凸轮轴 camshaft正时齿轮 timing gear燃油箱 fuel tank燃油泵 fuel pump汽油滤清器 gasoline filter 化油器 carburetor空气滤清器 air cleaner进气管 intake manifold排气管 exhaust manifold火花塞 spark plug点火线圈 ignition coil断电器 breaker蓄电池 storage battery发电机 generator水泵 water pump散热器 radiator风扇 fan放水阀 drain valve水套 water jacket分水管 distributive pipe机油泵 oil pump集滤器 suction filter限压阀 relief valve润滑油道 oil passage机油滤清器 oil filter机油冷却器 oil cooler起动机 starting motor有效功率 effective power有效转矩 effective torque燃油消耗率 specific fuel consumption发动机转速特性 engine speed characteristic节气门开度 throttle percentage部分特性 partial characteristic外特性 outer characteristic第二章曲柄连杆机构汽缸套 cylinder sleeve, cylinder liner发动机支承 engine mounting活塞顶 piston top活塞头部 piston head活塞裙 piston skirt开槽 slot活塞环 piston ring气环 compression ring油环 oil ring环槽 groove活塞销 piston pin主轴承 main bearing主轴承盖 main bearing cap主轴瓦 main shell连杆轴承 big end bearing连杆盖 big end cap起动爪 cranking claw带轮 pulley平衡重 counter weight发火顺序 firing order扭振减振器 torsional vibration damper第三章配气机构顶置气门 (OHV) Over Head Valve顶置凸轮轴 (OHC) Over Head Camshaft单顶置凸轮轴 (SOHC) Single Over Head Camshaft 双顶置凸轮轴 (DOHC) Dual Over Head Camshaft 多气门发动机 multi-valve engine气门间隙 valve clearance配气相位 timing phase气门杆 valve stem气门座 valve seat气门导管 valve guide气门弹簧 valve spring第四章汽油机供给系可燃混合气 combustion mixture消声器 silencer, muffler汽油 gasoline, petrol分馏 distil蒸发性 evaporating property热值 heat value抗爆性 anti-knock property辛烷值 (RON) Research Octane Number过量空气系数 coefficient of excessive air 理论混合气 theoretical mixture稀混合气 thin mixture浓混合气 thick mixture主供油系统 main supply system怠速系统 idle system加浓系统 thickening system加速系统 accelerating system浮子 float浮子室 float chamber针阀 needle valve量孔 metering jet阻风门 choke滤芯 filter cartridge沉淀杯 sediment cup泵膜 pump diaphragm油浴式 oil bath type石棉垫 a**estos pad预热 pre-heating汽油直接喷射 gasoline direct injection电控 electronic control多点喷射 muti-point injection单点喷射 single point injection电路控制 circuit control分电器信号 distributor signal空气流量信号 airflow signal冷却水温信号 water temperature signal第五章柴油机供给系输油泵 transfer pump喷油泵 fuel injection pump高压油管 high pressure fuel pipe发火性 ignition property黏度 viscosity凝点 condensing point备燃期 pri-combustion period速燃期 rapid combustion period缓燃期 slow combustion period燃烧室 combustion chamber统一燃烧室 united chamber球形燃烧室 ball shape chamber涡流室 turbulence chamber预燃室 pri-combustion chamber喷油器 injector精密偶件 precise couple柱塞 plunger出油阀 delivery valve调速器 governor两速调速器 two speed governor全速调速器 full speed governor定速调速器 fixed speed governor综合调速器 combined governor气动调速器 pneumatic governor机械离心式调速器 mechanical centrifugal governor 复合式调速器 complex governor喷油提前角调节装置 advancer飞块 flyweight联轴节 coupling粗滤清器 primary filter细滤清器 secondary filter涡轮增压器 turbocharger中间冷却器 intermediate cooler第七章冷却系节温器 thermostat防冻液 anti-freezing liquid补偿水桶 compensation reservoirV-带 V belt百叶窗 shutter大循环 big circulation小循环 small circulation散热翅片 fins第八章润滑系润滑剂 lubricant压力润滑 pressure lubrication飞溅润滑 splash lubrication润滑脂 grease机油压力传感器 oil pressure sensor油封 oil seal旁通阀 bypass valve机油散热器 oil cooler机油尺 dip stick加机油口 oil filler曲轴箱通风 crankcase ventilation第九章点火系一次绕组 primary winding二次绕组 secondary winding热敏电阻 heat sensitive resistance点火提前 ignition advance分电器 distributor活动触点 moving contact固定触点 fixed contact分火头 distributor rotor arm电容器 condenser点火提前装置 ignition advancer离心式点火提前装置 centrifugal ignition advancer 真空式点火提前装置 vacuum ignition advancer辛烷值校正器 octane number rectifier中心电极 central electrode侧电极 side electrode瓷绝缘体 ceramic insulator跳火间隙 spark gap半导体点火系 semi-conductor ignition system晶体管 transistor二极管 diode三极管 triode无触点点火系 non-contact ignition system霍尔效应 Hall effect正极板 anode负极板 cathode隔板 separator电解液 electrolyte蓄电池格 battery cell接线柱 terminal电缆 cable硅整流交流发电机silicon rectified A.C. motor转子 rotor定子 stator电刷 brush风扇叶轮 fan blade电压调节器 voltage regulator第十章起动系手摇起动 cranking电热塞 electric heater plug串激直流发电机 serial wound D.C. motor起动齿圈 starter ring电磁操纵机构 electro-magnetic control第十一章新型发动机三角活塞 triangular piston转子发动机 rotary engine自转 rotary motion, rotation公转 orbit motion轨迹 trajectory齿轮 gear齿圈 ring gear往复零件 reciprocal parts动平衡 dynamic balance燃气涡轮发动机 gas turbine第十二章汽车传动系机械式传动系 mechanical transmission液力机械式传动系 hydro-mechanical transmission静液式传动系 static-hydraulic transmission电力式传动系 electrical transmission自动式传动系 automatic transmission减速 reduction可变速比 variable ratios有级变速 definite ratios无级变速 indefinite ratios无级变速器(CVT) Continuously Variable Transmission 一般布置 general layout发动机横置 lateral engine positioning分动器 transfer case, transfer box第十三章离合器接合柔和 smooth engagement分离彻底 thorough separation过载 overload摩擦表面 friction surface摩擦衬片 friction liner毂 hub主动部分 driving part从动部分 driven part花键 spline压盘 pressure plate离合器盖 cover plate分离杠杆 release lever分离套筒 release sleeve分离轴承 release bearing主缸 master cylinder工作缸 working cylinder分离叉 release fork间隙调整 clearance adjustment打滑 slip踏板 pedal踏板自由行程 pedal free stroke踏板工作行程 pedal working stroke铆钉，铆接 rivet双片离合器 dual disc clutch中央弹簧离合器 central spring clutch膜片弹簧离合器 diaphragm spring clutch 非线性 non-linear第十四章变速器与分动器输入轴（第一轴）input shaft, drive shaft 输出轴（第二轴）output shaft, main shaft 中间轴 counter shaft倒挡轴 reverse gear shaft常啮合 constant mesh低速挡 low gear高速挡 high gear最高速挡 top gear空挡 neutral gear一挡 the first gear二挡 the second gear三挡 the third gear倒挡 reverse gear直接挡 direct gear超速挡 overdrive动力输出 power take-off换挡 shift啮合套 sliding sleeve同步器 synchronizer同步锥面 synchro cone变速杆 shifting lever手柄 handle球铰链 ball joint换挡拨叉 shifting fork自锁 self-lock互锁 inter-lock变速驱动桥 transaxle加力挡 low gear第十五章液力机械传动液力偶合器 hydraulic coupling泵轮 impeller涡轮 turbine叶片 blade液力变矩器 torque converter导轮 stator行星齿轮系 planetary gear system太阳轮 sun gear行星轮 planet pinion行星架 planet carrier齿圈 ring gear第十六章传动轴万向节 universal joint, U-joint十字轴式万向节Cardan type U-joint叉子 yoke, fork十字轴 spider, center cross滚针轴承 needle bearing滑脂嘴（油嘴）lubricating fitting, nipple等角速 constant angular velocity双联式万向节 dual Cardan type U-joint球叉式万向节 Weiss type U-joint球笼式万向节 Rzeppa type U-joint星形套 inner race housing球形壳 outer race shell保持架，球笼 retainer, ball cage挠性万向节 flexible U-joint无缝钢管 seamless steel tube第十七章驱动桥主减速器 final drive主动（小）齿轮 drive pinion从动（大）齿轮 ring gear伞齿轮 bevel gear双曲面齿轮 hypoid gear单级减速 single reduction双级减速 double reduction贯通式主减速器 penetrable final drive双速主减速器 double gear (speed) final drive 轮边减速器 wheel reduction差速器 differential半轴齿轮 differential side gear差速锁 differential lock轴间差速器 inter-axle differential lock托森差速器 torque sensitive differential。
汽车专业英语单词
汽车专业英语单词基本词汇和词组category 种类，类型body 车身chassis 底盘electrical equipment 电气设备brake 制动，制动器power train 传动系统steering 转向，操纵suspension 悬架allow for 考虑；允许refer to... as... 把……称为…component 部件，构件，元件capacity 容量，生产量passenger car 轿车commercial vehicle 商用车act as 担当，起作用，尽职责power unit 动力装置internal combustion engine 内燃机cylinder 气缸gasoline 汽油机spark 火花ignition 点燃，点火diesel 柴油机compression 压缩transmission 变速器；传输，传送crankshaft 曲轴，曲柄assembly 总成，装配shock 冲击clutch离合器torque converter 变矩器drive shaft 传动轴final drive 传动轴differential gear 差动齿轮，差速器transaxle 驱动桥（用于前轮驱动的汽车）engage 接合，啮合disengage 脱离steering box 转向器regardless of 不管，不顾absorber 减振器withstand 抵挡，经受住radial 放射状的，子午线的tubeless 无内胎的starter 起动机charge 充电alternator 交流发电机flywheel 飞轮，调速轮low-tension 低压的high-tension 高压的spark plug 火花塞consist of 由…组成supply 提供provide 提供primary circuit 初级回路secondary circuit 次级回路piston 活塞connecting rod 连杆crankshaft 曲轴power stroke 做功行程intake stroke 进气行程compression stroke 压缩行程exhaust stroke 排气行程inlet (intake) valve 进气阀exhaust valve 排气阀engine capacity 发动机排量revolution 旋转，转数compression ratio 压缩比engine block 发动机缸体cylinder head 气缸盖water jacket 使固定camshaft 凸轮轴alloy 合金intake manifold 进气总管oil pan 油底壳aluminum 铝drain off 排出，流出crankcase 曲轴箱，曲柄箱withstand 抵抗comprise 由……组成，包含inertia 惯性，惯量cylinder wall 气缸壁in place 在适当的位置bush 衬套，轴瓦，套筒rotary 旋转的align with 匹配timing gear 正时齿轮impulse 脉冲firing order 图表N. B. 注意，留心overhead camshaft 顶置凸轮轴dual 双的seesaw 跷跷板，杠杆valve clearance 气门间隙liable to 容易view... as...把……看成……parameter 参数，参量radius 半径，范围correspond with 相当于gear ratio 传动比crude 天然的characteristic 特性，特征；特有的，典型的vapor lock 气封，气阻，气塞( be) exposed to 易受……（的影响）antiknock 防爆的，抗爆的；防爆剂，抗爆剂audible 听得见的air/fuel ratio 空燃比mass 质量weak mixture 稀混合气rich mixture 浓混合气curve 曲线，弯曲compensate for补偿，偿还throttle 节气门idle speed 怠速in proportion to 与……成比例nozzle 喷嘴advance angle 提前角dwell angle 提前角actuator 执行器，调节器，调速控制器delivery line 出油管overflow line 溢流管leakage line 泄漏管feed pump 输油泵governor 调速器common rail 共轨thermostat 节温器，自动调温器circulation 循环radiation 辐射detach 分离relief valve 溢流阀tail pipe 排气尾管turn around 回转pollutant 污染物质grip [ grip ] 附着力，抓牢guarantee 保证，担保standstill 停止，停顿stationary 不动的，静止的depress 踩下slipping 打滑slave cylinder 从动缸powerplant 动力装置neutral 齿轮的空挡selector mechanism 换挡机构hydraulic 液压的planetary gear 行星齿轮sun gear 太阳轮planet carrier 行星架insulate 隔离sliding joint 滑动联轴器universal joint 万向节final drive 主减速器，后桥bevel 锥齿轮clearance 间隙differential 差速器align 使…成一行traction 牵引力service braking 行车制动parking braking 驻车制动drum brake 鼓式制动器disc brake 盘式制动器lock up 锁住，固定leading shoe 领蹄trailing shoe 从蹄adjuster 调节器，调停者fade 衰减instability 不稳定（性）distribution n．分配，分发adhesion 附着，粘着，粘附critical 临界的，危急的underbrake 制动不足antilock 防抱死的reserve 储备backup 备用的，辅助的；备份protocol 协议，草案emerge 出现，呈现，形成node 节点rigidity 刚性air-conditioning 空调dash panel 仪表板compressor 压缩机steering box 转向器king pin 主销Oversteer 过度转向Understeer 不足转向break-away 突然离开，脱离power steering 动力转向road feel 路感transverse 横向的crosswise 交叉的shock absorber 阻尼器，减振器front suspension 前悬架rear suspension 后悬架toe 轮胎缘距caster 主销倾角camber 车轮倾角front wheel alignment 前轮定位wheel 车轮rim 轮辋tire 轮胎inner tube 内胎auxiliary 附属设备auxiliary 附属设备lead-acid battery 铅酸电池owing to 由于，应归功于electrode 电极replace 补充conductor 导体mean value 平均值with (in) regard to 关于，对于，在……方面，按照wrap around 缠绕allow for 考虑static 静态的，静力的insufficient 不足的，不够的fine 细的in parallel 并联headlamp 前照灯sensor 传感器inertial 惯性的anti-theft system 防盗系统protocol 协议network 网络benefit（s）优点(复数)notice（s）要点(复数)module 模块application 应用hybrid drive 混合驱动，混合动力be superior to 优于，胜过fuel cell 燃料电池attribute 属性，品质，特征，加于，归结in excess of 多于，超过，过分难点内容hood （发动机）罩trunk deck行李箱盖cargo 货物sedan 私家轿车maximum 最大量，最大限度；晟多的，最大极限的saloon 轿车，餐车convertible 敝篷车van 有篷货车；用车搬运coach 长途汽车，四轮大马车tipper 翻斗车，自卸车flatbed 平板车tanker 罐车shaft 轴vertical 垂直的，直立的；垂直线，垂直面，竖向transverse 横向的，横断的longitudinal 纵向的，经度的mount 安装，装上，安放conventional 传统的，惯例的，常规的，习俗的hydraulic液压的coupling 半轴tie-rod 转向横拉杆，拉杆，连杆ball joint 球铰键disc brake 盘式制动器drum brake 鼓式制动器alloy 合金regulator 调节器，调整器distributor 分电器TDC 上止点BDC 下止点every other 旋转，转数knock 敲缸，敲打lubrication 润滑fasten 使固定gray iron 灰铸铁overhead-cam ( OHC) 顶置凸轮casting 铸件side force 侧向力tangential force 切向力radial force 径向力，法向力hollow 空的splash 飞溅let go 放开，松手coordinate 协调valve insert 气门座reinforce 加强mesh 相啮合inline engine 直列发动机distributed system 分布系统centralized system 集中系统processor 处理器distill 蒸馏petroleum 石油volatility 挥发性flammability 易燃，可燃性misfire 不发火，失火optimum 最适宜；最适宜的carburetor 化油器filter 滤清器impurity 杂质pickup 传感器throttle valve 喷管needle valve 针阀idling valve 怠速阀auxiliary-air device 附加／旁通空气装置uniform 统一的，相同的，一致的，均衡的interference 冲突，干涉superfine 特级的separate out 分（离）出，析出plunger-type 柱塞式speed droop 调速率combination governor 复合式调速器variable-speed governor 全程式调速器minimum-maximum-speed governor 两级式凋速器centrifugal 离心的brass 铜wax 蜡Intermediate 中间的muffler 消声器hydrocarbon 碳化氢carbon dioxide 二氧化碳three-way catalytic converter 三元催化转化器exhaust-gas recirculation 废气再循环Protrusion 露出，突出Equilibrium 平衡，平静，均衡Coefficient 系数counter shaft 中间轴throwout bearing 分离轴承clutch fork 分离叉pressure plate 压力盘sliding-mesh transmission 滑动啮合变速器constant-mesh transmission 常啮合变速器synchro-mesh transmission 同步啮合变速器reverse idler shaft 倒挡轴layshaft 副轴，中间轴countershaft 中间轴mainshaft 主轴pneumatic 气动的，有气胎的continuously variable transmission ( CVT) 无级变速器spider 十字轴,十字叉constant-velocity universal 等速万向节reversal 反转，反向，逆转coaxial 同轴的，共轴的longitudinally 纵向地transversely 横着conventional 传统的kinetic energy 动能retarding braking 缓速制动coefficient 系数aside from 除……以外（尚有）duo-servo 双力作用的magnitude 数量，巨大，大小duplex 双的，双重的vacuum brake booster 真空制动助力器tandem master cylinder 串列式制动主缸split-coefficient 附着系数criteria 准则，标准electro-hydraulic braking (EHB) 电液制动fail-safe mode 失效安全模式brake response 制动响应pedal feel 踏板感electromechanical braking system（EMB）机电制动系统brake by-wire 线控制动cruise control 巡航控制hill hold 坡道保持time-triggered 时间触发的vacuum brake booster 真空制动助力器tandem master cylinder 串列式制动主缸split-coefficient 附着系数criteria 准则，标准cam and roller 球面蜗杆和滚轮recirculating ball 循环球rack-and-pinion 齿轮齿条式electric power-assisted steering 电动助力转向hydraulic power steering 液压动力转向oscillation 振动，摆动rolling 沿纵轴的摆振pitching 沿横轴的摆振shimmying 沿转向主销的转向车轮摆振shimmy damper 转向轮减振器toe-in 轮胎前束positive camber 车轮外倾角negative camber 车轮内倾角positive caster 主销正倾角negative caster 主销负倾角windscreen wiper 风窗刮水器washer 洗涤器potential 电位，电势ampere hour 安[培]．[小]时(A．h) accumulator 蓄电池，积聚者magnetic field 磁场induced current 感应电流electromagnet 电磁capacitor 电容器relay 继电器series-wound 串联的，串绕的Subassembly 部件，组件overrunning-clutch 超速离合器homogeneous 均匀的，均一的primary coil 一次线圈secondary coil 一次线圈transformer 变压器contact-breaker 断电器buffer 缓冲器amplifier 放大器dip-beam lamp 斜光灯，近光灯main-beam lamp 主光灯，远光灯raw data 原始数据oxygen sensor 氧传感器inflate 膨胀，充气restraint 约束，制止，克制actuator switch 操作开关knob 按钮controller area network ( CAN) 控制器局域网local interconnect network ( LIN) 本地互联网wiring harness 线束，电气配线electromagnetic compatibility(EMC) 电磁兼容性。
汽车专业英语常见词汇
汽车专业英语常见词汇Aaccelerator加速者，加速器accelerometer加速计air filter空气滤清器air flow meter空气流量计air flow sensor空气流量传感器alternator 交流发电机ammeter电流表antifreeze 防冻剂antiknock 抗爆剂antilock 防抱死 armature电枢assemble 装配axle 轮轴，车轴Bbackbone 支柱；骨干baffle 挡板；隔板baffle plate 缓冲板，折流板ball joint球形接头band 传送带，传动Basic advance angle 基础点火提前角beam 梁，横梁earing journal 支承轴颈boil 沸点，沸腾bolt螺钉booster 助力器，加力器;附加装置 ,辅助装置bore 孔，口径；钻孔，凿孔bottom dead center下止点brake band 制动带brake booster 制动助力器brake caliper 制动卡钳brake fluid 制动液buffer 缓冲器bypass valve 旁通阀 bumper 汽车保险杠；防撞器，缓冲器Ccaliper 卡钳cam lobe 凸轮的凸角Cam Position Sensor 凸轮轴位置传感器camshaft 凸轮轴端隙carburetor 化油器center electrode中央电极centrifugal fan离心式鼓风机，离心式风扇chamfer 锥角；切角面；圆角charging system 充电系统chassis 底盘circuit 电路clamp 夹子；夹紧clog 阻塞clutch 离合器clutch fork离合器分离叉clutch housing 离合器壳clutch linkage 离合器操纵杠杆机构 clutch pack 离合器压盘 clutch pedal 离合器踏板coil spring螺旋弹簧，圈弹簧combustion chamber 燃烧室component元件 ,组 compression ratio 压缩比compression ring 压缩环，气环compressor 压缩机condenser冷凝器；电容器contact point 触点contra-rotating gears反转齿轮 cooling jacket 冷却水套cork 软木塞，软木制品counter-balanced weight 配重 countershaft中间轴crank arm曲柄臂crankcase 曲柄箱，曲轴箱 crankshaft 曲轴crash sensor 碰撞传感器cushion 垫子，软垫，衬垫cylinder block 汽缸体cylinder head 气缸盖Ddashboard 仪表盘destruction损坏detonation 爆震，爆燃diaphragm 膜片；膜片泵；隔板；遮光板；薄膜diesel 柴油机，内燃机differential差速器diode 二极管dipstick 油尺，水 [油 ] 位指示器disc brake 盘式制动器distortion变形，扭曲；扭转distributor cap分电器盖diverter valve 分流阀dog clutch 牙嵌 [爪式 ]离合器double helical 人字齿轮drag link 转向直拉杆drive belt传动皮带drive shaft 传动轴 drive train 动力传动系统drive wheel 驱动轮dry clutch 干摩擦离合器duralumin 硬铝，杜拉铝Eeccentric 偏心轮EGR 废气再循环装置electric arc 电弧electrode 电极 electromagnet电磁铁，电磁electromagnetic field电磁场emission 排放物 engine performance发动机性能evaporator 蒸发器，脱水器engine speed and position sensor发动机转速和位置传感器evaporator core 蒸发器芯excess air ratio 过量空气系数exciter 振荡器，激发器，励磁机exhaust 排气；排气装置exhaust gas 废气 exhaust manifold排气歧管exhaust valve 排气阀expansion valve 膨胀阀Ffastener 紧固件fender 挡泥板fiberglass 玻璃纤维，玻璃丝filler cap （汽油箱）加油口盖final drive 主减速器，主传动flange 凸缘，法兰frame 车架；结构front suspension 前悬架fuel filter燃油滤清器fuel injection燃油喷射fuel injection system燃油喷射系统fuel pump 燃油 fulcrum 支点，支轴，支柱Ggap 缺口，间隙，缝隙；差距gas tank 汽油箱gasoline engine 汽油机gear box 齿轮箱gear combination齿轮啮合governor 调节器，调速器groove 槽，凹槽；切口Hheadlight 前大灯 heat dissipation 热消散 heat transfer 热传导 high-pressure liquid refrigerant 高压液体制冷剂 hinge 铰链；折叶 hood 遮罩horsepower 马力 hub （轮）毂Iignition coil点火线圈ignitiondistributor点火分电器ignition key 点火开关ignition system点火系统ignition timing点火正时IGt signal 点火信号implement叶[涡，工作，泵]轮，转子indicator lamp指示灯inlet(intake) valve进气阀instrument panel仪表板intake ducting 进气管intake air temperature sensor进气温度传感器intake manifold进气歧管Kking pin 主销LLayshaft 中间轴leaf spring 钢板弹簧 lean mixture 稀混合气lubrication 润滑 lubrication oil 润滑油 lubrication system 润滑系Mmagnetic switch 磁力开关main bearing cap 主轴承盖mass 质量master cylinder 制动主缸modulator调节器manifold runner歧管通道muffler 消声器 Multi-disk clutch多片式离合器multipoint fuel injection多点喷射Nnavigation 导航needle 指针neutral 空挡nitrogen 氮 noxious 有害的 nozzle 喷嘴Oobsolete 过时的 bstacle 障碍（物） octane 辛烷oil filter 机油滤清器oil pump 油泵 oil-control ring 控油环one-way clutch 单向离合器oscillation 摆动 oscilloscope 示波器over-charging 过充电 overdrive 超速传动 overload vt. 使超载 n.负荷过多override switch 超越控制开关pad 衬垫 parameter 参数parking brake 驻车制动passenger compartment 驾驶室pedestal 轴承座penetration渗透periphery 周线petroleum 石油pinion 小齿轮 piston head 活塞顶部piston land 活塞环槽岸pitman arm 转向摇臂planet carrier行星齿轮架planetary gear set 行星齿轮系统plate 电容器板 ,极板 platinum白金，铂plunger 柱塞；冲杆；模冲；活塞power train动力传动系primary winding初级绕组propeller shaft传动轴purge valve 排气阀Ppacking bolt填料函 [盖]螺栓padded dash(客厢 )软包仪表板panel board操纵板，控制板panel lamps(车内照明 )仪表板灯panel lamps(车内照明 )仪表板灯park ／neutral驻车档／空档park assist驻车辅助装置 (如驻车用的超声波装置)pawl棘爪，止动爪，掣子pinion cage①行星齿轮架②差速器壳Rradiator散热器radiator cap 散热器盖，水箱盖rear suspension rear wheel drive 后轮驱动regulator 调节器relay 继电器release lever 分离杠杆relief valve 安全阀，卸压阀，溢流阀resonance 谐振，共振retainer 止推挡圈 rich mixture浓混合气ring wheel 齿圈road wheel 车轮roller 蜗轮后悬架rotor 转子；涡轮Ssafety sensors 安全传感器shock 振动silicone 聚硅氧；硅树脂sensor 传感器shock absorber 减震器servo 伺服，伺服系统shoe 制动蹄simplex type 单缸式single point fuel injection单点喷射single-piston floating caliper 单活塞，浮钳盘式制动器solenoid 螺线管；电磁线圈spark 火花；瞬间放电spark plug 火花塞sped up 加速spindle轴，转轴spiral cable螺旋电缆spline 花键连接；花键，键槽，齿条spline hub花键毂spoke 轮辐sprocket 链齿；带齿盘；星轮squeeze 挤stability 稳定性starter motor起动机starting system起动系统steering arm转向节臂steering column转向管柱steering knuckle 转向节steering knuckle arm 转向节臂steering gear 转向齿轮，转向器steering shaft 转向轴steering system 转向系。
汽车专业英语词汇
1.汽车专业英语词汇2.audio control switch[ɔ:djəu] [kəntrəul][switʃ]音响操纵开关3.automatic level control[ɔ:təmætik] 自动水平操纵装置4.automotive engine system引擎系统5.axle shaft [æksl] 车(主动)轴6.base plate 底盘7.battery [bætəri]蓄电池8.bearing [bɛəriŋ]轴承9.body 车体10.bolt [bəult] 螺栓11. bolt cap 螺栓帽12.bolt-fly wheel [hwi:l]飞轮螺栓13.brake system 剎车系统14.breathe pipe [bri:ð]通气管15.CD player CD机16.Center shaft [sentə][ʃɑ:ft] 中间轴17.clamp [klæmp]卡座18.clamp plate 压板19.clutch [klʌtʃ] 离合20.clutch system 离合器21.coil spring [kɔil]螺旋簧bustion chamber [kəmbʌstʃən] [tʃeimbə]燃烧室23. commutator [kɔmjuteitə]转换器pression spring[kəmpreʃən]压簧pressor 压缩机26.condenser [kəndensə]冷凝器27.connecting rod 连杆28.cooling system 冷却系统29.crank shaft [kræŋk] 曲轴30.cylinder block [silində]汽缸体31.cylinder block汽缸体32.cylinder sleeve [sli:v]气缸套33.displacemint 排气量34.Double end bolt [dʌbl][bəult]双头螺母35.dowel pin [dauəl] [pin]柱销36.drive shaft 传动轴37.dust shield [ʃi:ld] 防尘罩38.electrical equipment（appliance）[i lektrikəl][i kwipmənt] [əplaiəns] 电气设备39.end cover 端盖40.engine [endʒin]发动机41.exhaust valve [iɡzɔ:st][vælv]排气门42.fire extinguisher [ikstiŋɡwiʃə]灭火器43.flywheel 调速轮，飞轮44.four-wheel drive 四轮驱动45.fram assy 车架总成46.Front cover [frʌnt] [[kʌvə] 前盖47.Front Engine Front Drive F.F.式车辆48.Front Engine Rear Drive F.R.式车辆49.fuel filler pipe assy [fjuəl] [filə] [paip]加油管总成50.fuel inlet hose [inlet] [həuz] 进气硬管51.fuel level indicator [indikeitə] 汽油表52.fuel return pipe [ritə:n] 回油管53.fuel transfer pump [træns fə:] [pʌmp] 输油泵54.gasket [ɡæskit]密封垫55.gear lever [ɡiə] 操纵杆,变档杆56.generator [dʒenəreitə] 发动机57.handle [hændl] 手柄58.headlamp 头灯59.heat insulator [insjuleitə] 隔热板60.heat shield subassy 隔热罩组件61.heat-control valve 热操纵阀62. hex bolt [heks] [bəult] 六角头螺栓63.high pressure pump [preʃə]高压油泵64.houseing [hauziŋ] 壳体,外壳65.identification code [aidentifikeiʃən]标记66.idle mixture screw [aidl] [mikstʃə] [skru:] 怠速混合气调整螺钉67.idle tube [tju:b]怠速油管68.idling speed 怠速69.ignition coil type 点火线圈类型70.ignition coil [iɡniʃən]点火线圈71.ignition controller kəntrəulə]点火操纵器72.ignition key 点火钥匙73.ignition point 燃点74.ignition switch 点火开关75.ignition switch assy [iɡniʃən] [switʃ] 点火开关总成76.ignition System 点火系77.ignition wire [waiə]点火线78.impact reduction type outside rear view mirrors[ridʌkʃən] [riə]缓冲式后视镜79.impact test 冲击试验80.imported motor vehicle [vi:kl]进口机动车81.indicator lamp 指示灯82.indicator lamp, left turn 左转向指示灯83.indicator lamp, right turn 右转向指示灯84.indirectly controlled wheel 间接操纵车轮85.injection nozzle 喷油嘴86.injection pump [indʒekʃən] 喷油泵87.injector 喷油器88.inlet hole 进气孔89.inlet hose[həuz] 进风口90.inlet opening 进油口91.inlet tube 进油管92.inlet valve 进油阀93.inlet 进油口94.inner dimension 内部尺寸95.inner shaft 内半轴96.inner tube 内胎97.input shaft 输入轴98.input voltage [vəultidʒ]输入电压99.install panel [pænəl]安装板100.instrument panel assy. [instrumənt] [pænəl]外表板总成101.instrument panels 外表板102.intake and exhaust device [iɡzɔ:st]进排气装置103.intake heater 进气加热器104.intake manifold [mænifəuld]进气歧管105.intake valve 进气门106.intercooler [intə(:)ku:lə]中冷器107.intermediate plate [ɪntəmi:djət] 中联板108.intermediate shaft 中间轴109.internal fan [intə:nəl]内风扇110.in-use motor vehicles 在用车辆111.joint [dʒɔint] 接头112.knock 敲击rge-sized special 大型专用teral level 横向水平仪115.left fog lamp 左雾灯116.left headlamp 左前照灯117.left horn[hɔ:n] 左喇叭118.left steering [stiə]左转向119.left tail lamp 左尾灯120.length, width and height 全长、全宽、全高121.let in air 进气122.license lamp [laisəns]牌照灯123.light vehicles 轻型车辆124.lighting device 照明装置125.lighting system 照明系统126.lining 衬片127.loaded goods 装载物128.loading capacity [kəpæsiti]载重量129.loading platform [plætfɔ:m]货箱130.locating block [ləukeit] 限位块131.locating shaft 限位轴132.locking device 锁止装置133.logo-Great Wall motor in Chinese 长城汽车标牌134.long axis [æksis]长轴135.long-body 长车身136.lower pressure switch 低压开关137.lubricating oil [lu:brikeit]润滑油138.magnet [mæɡnit] 磁体139.main bearing [bɛəriŋ]主轴承140.main bearing 主轴承141.main injection jet [dʒet]主喷口142.main oil gallery [ɡæləri]主油道143.main spring 主簧144.Make and type 厂牌和型号145.management supervisor 主管人146.manual transmission [trænz miʃən]手动变速器，手排挡变速箱147.manufacturer [mænjufæktʃərə]制造者148.marker lamp, left front 左前示廓灯149.marker lamp, right front 右前示廓灯150.master cylinder body 制动主缸缸体151.master cylinder cover 制动主缸缸盖152.max power 最大功率153.maximum loading capacity [mæksiməm] [kəpæsiti]最大载重量154.maximum output 最大输出功率155.measuring tape 卷尺156.mechanical steering 机械转向器157.metering rod 计量杆158.microphone 话筒159.mini-sized motor vehicle 小型机动车160.mini-sized 微型161.mirror for immediate front obstacle 前邻障碍观看镜162.motor vehicle category 机动车类别163.motor vehicle 机动车164.motor-driven cycle 摩托车165.nut 螺母166.oil block plate 挡油板167.oil drain groove [drein] [ɡru:v]导油槽168.oil filter [filtə]机油滤清器169.oil filter机油滤清器170.oil guide nozzle [nɔzl] 导油嘴171.oil pressure gauge [ɡeidʒ]机油压力表172.oil pump 机油泵173.oil trough [trɔ(:)f] 油槽174.overall height 总高175.overall length 总长176.overall width 总宽177.ping 爆声178.piston [pistən]活塞179.plastic nut [plɑ:stik] 塑料螺母180.Power 电源181.power steering 动力转向182.push rod 推杆183.radiator 散热器184.radiator fan [reidieitə]散热风扇185.regulator [reɡjuleitə]调整器186.return spring 复位弹簧187.reverse gear lever [rivə:s][ɡiə] 倒档拨杆188.revolution transmitter [revəlu:ʃən] [trænz mit] 转速传感器189.rivet [rivit] 铆钉190.roof handle 车顶扶手191.rotating shaft [rəuteit] 转轴192.rub hose [həuz]橡胶管193.screw [skru:]螺钉194.seal ring [si:l] 密封环195.seat belt 安全带196.self lock spring 自锁弹簧197.shaft-shifting fork 换档轴198.shaft-shifting fork [fɔ:k] 变速叉轴199.shift rocker [rɔkə]换档摇臂200.shifting block [ʃift] [blɔk] 换档拨块201.Shifting fork NO.1 一号拨叉202.shifting shaft 换挡轴203.shim [ʃim] 垫片204.shock absorber 避震器205.side cover 侧盖206.spacing spring [speisiŋ]限位弹簧207.spark plug 火星塞208.spark wire 高压电线209.Speaker 扬声器210.speedometer drive [spidɔmitə]速率表211.splint [splint] 夹板212.sponge cushion [spʌndʒ] [kuʃən]海绵垫213.stabilizer bar 平稳杆214.starting motor 起动马达215.steering wheel assembly [əsembli] 方向盘总成216.sunroof 天窗217.switch 开关218.tail door glass 后背门玻璃219.temperature control switch [tempəritʃə] [kəntrəul] 温度操纵开关220.tie band 扎带221.tire size 轮胎尺寸222.tire tube 内胎223.vacuum pipe [vækjuəm]真空管224.vacuum regulatory [reɡjuleit]真空调剂器225.ventilation plug [ventileiʃən] 通气塞226.vibration damper 减震器227.waste gate 废汽门228.water pump 水泵229. wheel 车轮230.wheel balance 轮胎平稳231.wheel rim 钢圈232.wheel rim, tire 钢圈与车胎。
最全汽车行业术语英文翻译
最全汽车行业术语英文翻译1. 汽车类型- Sedan: 轿车- Hatchback: 掀背车- SUV (Sport Utility Vehicle): 运动型多功能车- MPV (Multi-Purpose Vehicle): 多功能车- Coupe: 轿跑车- Convertible: 敞篷车- Pickup: 皮卡车- Van: 面包车- Electric Vehicle (EV): 电动汽车- Hybrid Vehicle: 混合动力汽车2. 发动机和动力系统- Engine: 发动机- Horsepower (HP): 马力- Torque: 扭矩- Fuel Injection: 燃油喷射- Turbocharger: 涡轮增压器- Supercharger: 机械增压器- Cylinder: 气缸- Transmission: 变速器- Manual Transmission: 手动变速器- Automatic Transmission: 自动变速器- Continuously Variable Transmission (CVT): 连续变速器- Four-Wheel Drive (4WD): 四轮驱动- All-Wheel Drive (AWD): 全轮驱动- Electric Motor: 电动机- Battery Pack: 电池组3. 车身部件- Chassis: 底盘- Bodywork: 车身- Hood: 发动机盖- Trunk: 后备箱- Bumper: 保险杠- Fender: 车翼- Door: 车门- Windshield: 前挡风玻璃- Roof: 车顶- Spoiler: 尾翼- Headlights: 前灯- Taillights: 尾灯4. 汽车零部件- Brakes: 制动器- Suspension: 悬挂系统- Steering Wheel: 方向盘- Tires: 轮胎- Exhaust System: 排气系统- Air Conditioning: 空调系统- Radiator: 散热器- Battery: 电池- Alternator: 发电机- Starter Motor: 起动机- Fuel Pump: 燃油泵- Ignition System: 点火系统5. 汽车性能指标- Acceleration: 加速度- Top Speed: 极速- 0-60 mph Time: 0-96公里/小时加速时间- Fuel Efficiency: 燃油效率- Range: 续航里程- Curb Weight: 空载重量- Gross Vehicle Weight (GVW): 总重量- Wheelbase: 轴距6. 安全设备- Seatbelt: 安全带- Airbags: 气囊- Anti-lock Braking System (ABS): 防抱死制动系统- Electronic Stability Control (ESC): 电子稳定控制系统- Tire Pressure Monitoring System (TPMS): 轮胎气压监测系统- Adaptive Cruise Control: 自适应巡航控制- Blind Spot Detection: 盲点监测以上是最全汽车行业术语的英文翻译，希望能对您有所帮助！。
汽车英语专业词汇(完全篇)
底盘平移台chassis shuttle车辆转移台bus transfer前围角板front wall angle cover后围侧板rear wall side cover保险杠bumper三类底盘three type chassis左侧围应力蒙皮R/S stretching skin (road side)中涂floating coat拼装台collector切割轮口wheel -arch cutting内饰trim线束harness返工re-doing轮罩护板wheel house发车前准备pre-delivery举升hoist小批量产品be pilot2 套two kits配电站power transformer substation裙板skirt发动机托架engine holding frame诊断报警系统diagnosis and alarming system互换性interchangeability缩微图纸microfiche files总装final assembly磷化phosphate仪表板dash board切齐trimming结构完整性structure integrity自动愈合的防腐材料self-healing corrosion preventative material 长途客车inter-city bus改装厂refitting factory遮阳板sun visor随车工具tool box钢化玻璃toughened grass异形钢管special steel pipe全天候空调系统full range A/C强制通风ram-air ventilation停机时间downtime无公害柴油clean diesel宽敞悬臂式座椅roomy cantilevered seat防滑地板no-skid floor织物纹里铝合金textured aluminum extrusion爬坡能力grade ability排水阀drain valve除湿器moisture ejector怠速时at idle琴式驱动桥banjo type drive axle通风口duct恒温控制thermostatic control平衡水箱surge tank变光开关simmer switch消音器muffler防破坏vandal resistant聚碳化透镜poly-carbonate Len镀锌板galvanized plate搭接lap亮丽的外表smart appearance隐藏式固定concealed fastening水洼pending发动机中置式客车bus with under floor engine组合式客车车身modular bus body薄壳式结构shell construction衬垫pad空气导流板air deflector搁梁shelf beam腰梁waist rail梭梁stabilizing beam腰带式安全带diagonal safety belt压条trim strip嵌条insertion strip翼板fender斜撑bracing piece转向盘回正性试验test of steering wheel return ability转向盘转角脉冲试验steering wheel impulse input test转向盘转角阶跃输入试验steering wheel step input or transient state yaw response test极限侧向加速度试验limiting lateral acceleration test汽车平顺性随机输入行驶试验automobile ride random input running test汽车平顺性单脉冲输入行驶试验automobile ride single pulse input running test汽车悬挂系统固有频率与阻尼比的测定试验measurement of natural frequency and damping ratio of suspension功率突然变化影响试验test of effect of sudden power change收油门后控制试验test of control at breakaway横风稳定性试验test of crosswind stability反冲试验kick-back test轮胎爆破响应时间试验test of burst response of tire绕过障碍物试验obstacle avoidance test移线试验lane change testJ型转弯试验test of J turn频率响应时间试验frequency response test瞬态响应时间试验transient response test阶路响应时间试验step response test脉冲响应试验pulse response test静态操舵力试验static steering effort test悬架举升试验jack-up test of suspension耐翻倾试验test of overturning immunity轮辋错动试验rim slip test风洞试验wind tunnel test制动稳定性试验test of braking stability最小转弯直径试验minimum turning diameter test操舵力试验steering effort test类型type发动机engine内燃机internal combustion engine动力机装置power unit汽油机gasoline engine汽油喷射式汽油机gasoline-injection engine火花点火式发动机spark ignition engine压燃式发动机compression ignition engine往复式内燃机reciprocating internal combustion engine 化油器式发动机carburetor engine柴油机diesel engine转子发动机rotary engine旋轮线转子发动机rotary trochoidal engine二冲程发动机two-stroke engine四冲程发动机four-stroke engine直接喷射式柴油机direct injection engine间接喷射式柴油机indirect injection engine增压式发动机supercharged engine风冷式发动机air-cooled engine油冷式发动机oil-cooled engine水冷式发动机water-cooled engine自然进气式发动机naturally aspirated engine煤气机gas engine液化石油气发动机liquified petroleum gas engine柴油煤气机diesel gas engine多种燃料发动机multifuel engine石油发动机hydrocarbon engine双燃料发动机duel fuel engine热球式发动机hot bulb engine多气缸发动机multiple cylinder engine对置活塞发动机opposed piston engine对置气缸式发动机opposed-cylinder engine十字头型发动机cross head engine直列式发动机in-line engine星型发动机radial engine筒状活塞发动机trunk-piston engine斯特林发动机stirling engine套阀式发动机knight engine气孔扫气式发动机port-scavenged engine倾斜式发动机slant engine前置式发动机front-engine后置式发动机rear-engine中置式发动机central engine左侧发动机left-hand engine右侧发动机right-hand engine短冲程发动机oversquare engine长冲程发动机undersquare engine等径程发动机square engine顶置凸轮轴发动机overhead camshaft engine双顶置凸轮轴发动机dual overhead camshaft engine V形发动机V-engine顶置气门发动机valve in-head engine侧置气门发动机side valve engine无气门发动机valveless engine多气门发动机multi-valve engine卧式发动机horizontal engine斜置式发动机inclined engine立式发动机vertical engineW形发动机w-engineI形发动机I-engineL形发动机L-engineF形发动机F-engine性能performance二冲程循环two-stroke cycle四冲程循环four-stroke cycle狄塞尔循环diesel cycle奥托循环otto cycle混合循环mixed cycle定容循环constant volume cycle工作循环working cycle等压循环constant pressure cycle理想循环ideal cycle热力循环thermodynamic cycle冲程stroke活塞行程piston stroke长行程long stroke上行程up stroke下行程down stroke进气行程intake stroke充气行程charging stroke压缩行程compression stroke爆炸行程explosion stroke膨胀行程expansion stroke动力行程power stroke排气行程exhaust stroke膨胀换气行程expansion-exchange stroke换气压缩行程exchange-compression stroke止点dead center上止点top dead center(upper dead center)下止点lower dead center(bottom dead center)上止点前budc(before upper dead center)上止点后atdc(after top dead cetner)下止点前bbdc(before bottom dead center)下止点后abdc(after bottom dead center)缸径cylinder bore缸径与行程bore and stroke空气室energy chamber气缸余隙容积cylinder clearance volume燃烧室容积combustion chamber volume气缸最大容积maximum cylinder volume压缩室compression chamber排气量displacement发动机排量engine displacement活塞排量piston swept volume气缸容量cylinder capacity单室容量single-chamber capacity容积法volumetry压缩比compression ratio临界压缩比critical compression ratio膨胀比expansion ratio面容比surface to volume ratio行程缸径比stroke-bore ratio混合比mixture ratio压缩压力compression pressure制动平均有效压力brake mean effective pressure(bmep) 空燃比air fuel ratio燃空比fuel air ratio燃料当量比fuel equivalence ratio扭矩torque单缸功率power per cylinder升功率power per liter升扭矩torque per liter升质量mass per liter减额功率derating power输出马力shaft horsepower马力小时，马力时horsepower-hour总马力gross horse power总功率gross power净功率net power燃油消耗量fuel consumption比燃料消耗率specific fuel consumption空气消耗率air consumption机油消耗量oil consumption有效马力net horse power额定马力rated horse power马力重量系数horsepower-weight factor制动功率brake horse power制动热效率brake thermal efficiency总效率overall efficiency排烟极限功率smoke limiting horsepower功率曲线power curve机械损失mechanical loss机械效率mechanical efficiency有效热效率effective thermal efficiency充气系数volumetric efficiency过量空气系数coefficient of excess air适应性系数adaptive coefficient扭矩适应性系数coefficient of torque adaptibility转速适应性系数speed adaptive coefficient强化系数coefficient of intensification校正系数correction factor换算系数conversion factor活塞平均速度mean piston speed发动机转速engine speed (rotational frequency)怠速转速idling speed经济转速economic speed起动转速starting speed最低稳定工作转速lowest continuous speed with load 最大扭矩转速speed at maximum torque最高空转转速maximum no load governed speed调速speed governing超速overspeed怠速idling转速波动率speed fluctuation rate工况working condition(operating mode)额定工况declared working condition变工况variable working condition稳定工况steady working condition空载no-load全负荷full load超负荷overload部分负荷part load充量（进气）charge旋转方向direction of rotation顺时针clockwise逆时针counter-clockwise左转left-hand rotation右转right-hand rotation外径major diameter中径pitch diameter内径minor diameter径向间隙radial clearance发动机性能engine performance加载性能loading performance起动性能starting performance加速性能acceleration performance动力性能power performance排放性能emission performance空转特性no load characteristics负荷特性part throttle characteristics调速特性governor control characteristics万有特性mapping characteristics稳定调速率steady state speed governing rate 气缸体和气缸盖cylinder block and head气缸体cylinder block整体铸造cast inblock (cast enblock)发动机罩engine bonnet气缸体加强筋engine block stiffening rib气缸cylinder（转子机）缸体stator缸径cylinder bore气缸体机架cylinder block frame气缸盖cylinder head配气机构箱valve mechanism casing气缸体隔片cylinder spacer气缸盖密封环cylinder head ring gasket气缸盖垫片cylinder head gasket气缸套cylinder liner(cylinder sleeve)干式缸套dry cylinder liner湿式缸套wet cylinder liner气缸水套water jacket膨胀塞expansion plug防冻塞freeze plug气缸壁cylinder wall环脊ring ridge排气口exhaust port中间隔板intermediate bottum导板guideway创成半径（转子机）generating radius缸体宽度（转子机）operating width机柱column燃烧室combustion chamber主燃烧室main combustion chamber副燃烧室subsidiary combustion chamber预燃室prechamber涡流燃烧室swirl combustion chamber分开式燃烧室divided combustion chamber涡流式燃烧室turbulence combustion chamber半球形燃烧室hemispherical combustion chamber浴盆形燃烧室bathtub section combustion chamberL形燃烧室L-combustion chamber楔形燃烧室wedge-section combustion chamber开式燃烧室open combustion chamber封闭喷射室closed spray chamber活塞顶内燃烧室piston chamber爆发室explosion chamber燃烧室容积比volume ratio of combustion cahmber燃烧室口径比surface-volume ratio of combustion chamber 通道面积比area ratio of combustion chamber passage曲轴箱通气口crankcase breather凸轮轴轴承座camshaft bearing bush seat定时齿轮室罩camshaft drive(gear)cover曲轴箱检查孔盖crankcase door曲轴箱防爆门crankcase explosion proof door主轴承盖main bearing cap气缸盖罩valve mechanism cover飞轮壳flywheel cover扫气储器scavenging air receiver活塞piston裙部开槽活塞split skirt pistonU形槽活塞U-slot piston滚花修复活塞knurled piston圆顶活塞dome head piston平顶活塞flat head piston凸顶活塞crown head piston(convex head piston)凹顶活塞concave head piston阶梯顶活塞step-head piston筒形活塞trunk piston椭圆形活塞oval piston抗热变形活塞autothermic piston不变间隙活塞constant clearance piston镶因瓦钢片活塞invar strut piston直接冷却式活塞direct-cooled piston间接冷却式活塞indirect cooled piston滑裙活塞slipper piston活塞速度piston speed活塞顶部piston head活塞裙部piston skirt整体活塞裙solid skirt活塞裙扩大衬簧piston skirt expander滑履式活塞裙slipper skirt隔热槽heat dam活塞标记piston mark活塞销piston pin活塞销孔piston pin boss活塞销衬套piston pin bushing全浮式活塞销full-floating piston pin半浮式活塞销semifloating piston pin固定螺钉式活塞销set screw piston pin活塞环piston ring组合式活塞环compound piston ring同心活塞环concentric piston ring偏心活塞环eccentric piston ring自由环free ring闭合环closed ring梯形环keystone ring半梯形环half keystone ring矩形环rectangular ring油环oil control ring开槽油环slotted oil control ring螺旋弹簧加载双坡口油环coil spring loaded slotted oil control ring 涨环expander双坡口油环double bevelled oil control ring内上坡口internal bevel top内下坡口internal bevel bottom边缘坡口油环bevelled-ege oil control ring刮油环scrapper ring钩形环napier ring镀铬活塞环chrome plated piston ring活塞衬环piston ring expander活塞环槽piston ring groove活塞环区ring zone活塞环岸piston ring land活塞环内表面back of ring曲柄连杆机构connecting rod中心曲柄连杆机构central-located connecting rod 偏心曲柄连杆机构offset connecting rod铰接曲柄边杆机构hinged connecting rod连杆connecting rod连杆小头connecting rod small end连杆大头connnecting rod big end连杆杆身connecting rod shank副连杆slave connecting rod叉形连杆fork-and-blade connecting rod主连杆main connecting rod方形连杆boxed rod绞链式连杆hinged type connecting rod活节式连杆articulated connecting rod连杆盖connecting rod cap连杆轴承connecting rod bearing曲轴crankshaft整体式曲轴one-piece crankshaft组合式曲轴assembled crankshaft右侧曲轴right-hand crankshaft左侧曲轴left-hand crankshaft改变行程的曲轴stroked crankshaft曲轴前端crankshaft front end曲轴主轴颈crankshaft main journal轴颈重叠度shaft journal overlap圆角fillet主轴承main bearing曲轴止推轴承crankshaft thrust bearing薄臂轴瓦thin wall bearing shell曲轴油道crankshaft oil passage曲柄crank曲柄臂crank arm曲柄销crank pin轴套bush曲柄转角crank angle曲柄半径crank radius抛油圈oil slander角度轮degree wheel动平衡机dynamic balancer平衡重balancer weight扭振减振器torshional vibration damper扭振平衡器torsion balancer谐振平衡器harmonic balancer振动平衡器vibration balancer曲轴链轮crankshaft sprocket转子轴颈rotor journal偏心轴eccentric shaft曲轴箱crankcase闭式曲轴箱通风装置closed-crankcase ventilating system 飞轮flywheel飞轮齿圈flywheel ring gear飞轮芯棒cantilever飞轮芯轴flywheel spindle飞轮的惯量矩flywheel moment of inertia飞轮标记flywheel mark当量系统equivalent system当量轴长equivalent shaft length一级往复惯性力reciprocating inertia force,1st order二级往复贯性力reciprocating inertia force, 2nd order离心惯性力centrifugal inertia force配气机构valve gear凸轮轴camshaft凸轮cam整体式凸轮轴one-piece camshaft组合式凸轮轴assembled camshaft凸轮轴驱动机构camshaft drive赛车用凸轮轴race camshaft凸轮轴轴颈camshaft bearing journal凸轮轴轴承camshaft bearing凸轮轴偏心轮camshaft eccentric凸轮轴链轮camshaft sprocket凸轮轴正时齿轮camshaft timing gear凸轮轴齿轮camshaft gear wheel进口凸轮inlet cam排气凸轮exhaust cam快升凸轮quick lift cam快升缓降凸轮quick lift gradual clsing cam凸轮轮廓cam contour凸轮包角cam angle凸轮升程cam-lobe lift凸轮尖cam nose凸轮从动件cam follower齿轮传动机构gear drive正时齿轮timing gear链传动机构chain drive链轮sprocket wheel链轮盘chain sprocket正时链条timing chain带齿皮带toothed timing belt链条张紧轮chain tension gear半速齿轮half speed gear正时齿轮刻印记号timing gear punch mark气门valve进气过程intake process换气过程gas exchange process扫气过程scavenging process给气比delivery ratio分层充气stratified charge充量系数volumetric efficiency涡流比swirl rate进气涡流intake swirl螺旋进气道进气helical duct intake导流屏式气门进气masked valve intake切向进气道进气tangential duct intake进气紊流intake trubulence进气提前角intake advance angle进气持续角intake duration angle进气迟后角intake lag angle进面值time-area value气门升程valve lift气门正时valve timing扫气口面积scavenging port area菌形气门mashroom valve, poppet valve钠冷却气门sodium filled valve(natrium cooled valve) 双气门dual valve进气门intake valve (suction valve,inlet valve)排气门exhaust valve顶置气门overhead valve侧置气门side valve倾斜气门inclined overhead valve直立气门vertical overhead valve套筒式滑阀sleeve valve气门机构valve gear直接式气门驱动机构direct valve gear间接式气门驱动机构indirect valve gear气门杆valve stem加大气门杆oversize valve stem气门头valve head气门工作面valve face气门边限valve margin气门弹簧座valve-spring retainer气门锁片valve key气门间隙调节螺钉valve lash adjusting screw气门旋转器valve rotator气门室valve cage气门油封valve oil seal气门口valve port气门座valve seat气门座镶圈（嵌镶式气门座圈）valve seat insert(valve seat ring) 气门座锥角valve seat angle气门座宽度valve seat width气门挺杆valve tappet(valve lifter)液力挺杆hydraulic tappet(lifter)无间隙挺杆zero-rush tappet (non-clearance tappet)筒形挺杆barrel type tappet油压挺杆ooil tappet滚轮挺杆roller tappet(lifter)挺杆转位tappet rotation排气门挺杆exhaust valve lifter气门导管valve guide气门杆导管stem guide气门重叠度stem overlap气门开启持续时间valve duration气门正时标记valve timing sign气门弹簧valve spring气门内弹簧inner valve spring气门外弹簧outer valve spring刚性缓冲弹簧stiff buffer spring上紧弹簧energizing spring防振气门弹簧non-surging spring弹簧座圈spring retainer蝶形弹簧belleville spring滚柱roller气门室盖valve chamber cover摇臂rocker arm高升程摇臂high lift rocker arm摇臂轴rocker arm shaft推杆push-rod摇臂支架rocker arm bracket气门摇臂室罩valve rocker chamber cover导向轮guide wheel导杆slide bar导轨slide rail张紧轮tensioning wheel链条张紧调节装置assembly chain tension adjuster张紧带轮tensioning pulley传动带张紧装置belt tensioner同步驱动皮带synchronous belt同步驱动皮轮synchronous belt pulley供油系fuel system控制燃烧系统controlled combustion system反湿气装置antipercolator电子燃油喷射electronic fuel injection蒸气回收装置vapor recovery system燃油蒸气回收系统fuel vapor recovery system液体回收装置liquid withdrawal system恒量净化管constant purge line碳罐净化管canister purge line供油量fuel delivery循环供油量fuel delivery per cycle额定供油量rated fuel delivery怠速供油量idling speed fuel delivery供油规律fuel supply rate curve油量调节装置fuel control unit供油提前角fuel supply advance angle进油计量inlet metering几何供油行程geometric fuel delivery stroke供油率fuel supply rate燃油通道fuel gallery有效行程effective stroke剩余行程remainder stroke变行程计量variable stroke metering等容卸载constant volume unloading变容卸载variable volume unloading收缩容积retraction volume燃油喷油装置fuel injection equipment燃油喷射泵fuel injection pump滚轮式燃油喷射泵roll fuel injection pump凸轮轴式燃油喷射泵camshaft fuel injection pump直列式燃油喷射泵in-line fuel injection pump伺服式燃油喷射泵servo fuel injection pump底部突缘安装燃油喷射泵base flanged mounted fuel injection pump 上部安装燃油喷射泵high flanged-mounted fuel injection pump侧向安装燃油喷射泵side-mounted fuel injection pump端部突缘安装式燃油喷射泵end flange-mounted fuel injection pump V形燃油喷射泵vee fuel injection pump脉动式燃油喷射泵jerk fuel injection pump螺纹安装燃油喷射泵screw-mounted fuel injection pump蓄能式燃油喷射泵accumulator fuel injection pump往复式燃油喷射泵reciprocating fuel injection pump驱动轴式燃油喷射泵driveshaft fuel injection pump单缸式燃油喷射泵single cylinder fuel injection pump圆柱式燃油喷射泵cylindrical fuel injection pump旋转式燃油喷射泵rotary fuel injection pump分配式燃油喷射泵distributor fuel injection pump多缸燃油喷射泵multicylinder fuel injection pump框架安装式燃油喷射泵cradle mounted injection pump喷油始点fuel injection beginning喷油终点fuel injection end喷油持续角fuel injection duration angle喷油延迟injection delay引燃喷射pilot injection启喷压力injection starting pressure峰值喷油扭矩peak injection torque峰值喷油压力peak injection pressure喷油泵油缸数目number of cylinders of an injection pump无气喷射solid injection喷射正时injection timing集中喷射group injection喷油器injector整体式喷油器unit injector喷嘴nozzle轴针式喷嘴pintle type nozzle环槽式喷嘴annular slot nozzle孔式喷嘴hole type nozzle长杆喷嘴long stem nozzle孔板式喷嘴orifice plate nozzle开式喷嘴open nozzle闭式喷嘴closed nozzle喷油提前器timing advance unit喷射泵壳体injection pump housing针阀needle芯轴central spindle喷嘴壳体nozzle body针阀升程needle lift喷嘴盖形螺母nozzle cap nut喷油器壳体nozzle holder突缘安装喷油器壳体flanged-mounted injection nozzle holder 燃油喷射泵传动装置transmision of an injection pump喷嘴锥体nozzle hole cone柱塞plunger柱塞套barrel柱塞行程plunger stroke喷孔spray orifice海拔控制器altitude control提前器飞锤flyweight喷孔长径比ratio of nozzle hole length nozzle diameter喷嘴液动力特性nozzle hydrokinetic characteristics动态相位dynamic phase喷孔面积nozzle hole area喷嘴流通特性nozzle flow characteristic喷油背压injection back pressure高压油管high pressure pipe平均喷油扭矩mean injection torque喷油总效率overall pumping efficiency峰值喷油压力injection peak pressure预行程prestroke收缩行程retraction stroke燃油箱fuel tank油箱盖fuel tank油位表fuel level gauge注油控制装置fill control system汽油箱gasoline tank( petrol tank)汽油供给管gasoline feed pipe加油管filler tube放油螺塞drain plug吸油管suction pipe刚性燃油管rigid fuel pipe进油孔fuel feed hole供油管supply pipe通气管bleeding pipe通气管bleeding pipe泄油阀spill valve泄油孔口spill port进油阀inlet valve最大油量限制器maximum fuel stop滴油dribble燃油表fuel gauge输油泵feed pump燃油泵fuel pump附装燃油箱中的电动燃油泵tank-mounted eletric fuel pump 机械式燃油泵mechanical fuel pump膜片式燃油泵diaphragm fuel supply pump叶片式供油泵vane fuel supply pump活塞式输油泵piston type fuel supply pump齿轮式输油泵gear fuel supply pump电动燃油泵eletric fuel pump带真空泵的汽油泵vacuum pump with fuel pump起动加油器primer起动给油杆primer lever燃油泵上体fuel pump body燃油泵下体fuel pump base燃油泵盖bowl cover进油口接头fuel inlet neck出油口接头fuel discharge port输出阀delivery valve泵油元件pump element回油阀部件fuel return valve assembly化油器carburetor化油器系统carburetor circuit简单化油器elementary carburetor单腔化油器single-barrel carburetor双腔并动化油器two-barrel dual carburetor双腔分动化油器two-barrel duplex carburetor四腔化油器four-barrel carburetor上吸式化油器updaught carburetor下吸式化油器downdraught carburetor平吸式化油器horizontal carburetor侧吸式化油器side-draft-carburetor高海拔补偿式化油器altitude compensating carburetor 化油器附加器adaptor carburetor双腔式化油器twin-choke carburetor固定喉管式化油器fixed venturi carburetor可变喉管化油器variable venturi carburetor化油器接头carburetor adaptor阻风门choke valve阻风活塞choke piston阻风板choke plate自动阻风门automatic choke阻风门拉钮choke button电控自动阻风门electric-assisted choke阻风管choke tube喉管venturi双重或三重喉管double & triple venturi阻风门拉线choke cable化油器小喉管booster venturi浮子系float system浮子float环形浮子annular float同心式浮子concentric float浮子支销float hinge pin浮子针阀float needle valve阀针valve needle浮子油面float level浮子臂float arm侧置浮子室式side float type怠速阀idle valve怠速针阀idle needle省油器economizer省油器阀economizer valve辅助空气阀auxiliary air-valve加速油井accelerating well加速泵accelerating pump加速泵喷嘴accelerating pump nozzle油门throttle手油门hand throttle节气门操纵手柄throttle control lever真空加浓器vacuum booster加浓器excess fuel device量孔体jet block怠速量孔idle metering jet主量孔main metering jet剂量阀活塞dosage valve piston空气量孔air jet燃油滤清器fuel filter沉淀杯sediment bowl串联过滤器in-line filter燃油箱内装过滤器in-tank filter调速器governor飞球式调速器flyball governor调速器governor飞球式调速器flyball governor液压调速器hydraulic governor真空转速调速器vacuum speed governor惯性调速器inertia governor离心调速器centrifugal governor调速器重锤governor weight空气滤清器及进排气系统air cleaner and intake and exhaust sytem 空气滤清器air filter冲压式空气滤清器ram air clearner恒温控制式空气滤清器thermostatic controlled air cleaner油浴式空气滤清器oil bath air cleaner纸质空气滤清器paper air clearner旋流管式空气滤清器swirl tube air filter滤清器滤芯filter element空气滤清器壳体air filter housing空气滤清器盖air filter cover滤清器密封圈filter seal ring滤网sieve滤纸盘或膜filter paper disc or membrane进气和排气系统intake and exhaust system排气管exhaust pipe排气抽气管exhaust extraction duct扫气泵scavenging pump进气预热装置intake preheater进气歧管intake manifold进气歧管真空度intake manifold vacuum冷式进气歧管cold manifold冲压式进气歧管ram intake manifold排气歧管exhaust manifold脉冲式排气歧管pulse exhaust manifold等压排气歧管constant pressrue exhaust manifold排气歧管热量控制阀exhaust manifold heat control valve超高度歧管high-rise manifold升温横跨管道heat crossover排气横跨管道exhaust crossover预热点hot spot阻风门加热器choke heater热空气导流管hot air duct隔热板heat shield排气再循环阀exhaust -gas-recirculation消声器silencer进气消声器intake silencer排气消声器exhaust silencer金属垫片式消声器steel pack muffler玻璃丝消声器glass pack muffler空洞消声器gutted muffler前排气管front exhaust pipe尾管tail pipe消声器联接管intermediate pipe热空气管hot air pipe曲轴箱通风管crankcase bleed pipe隔声罩acoustic hood进气消声器元件silencer element真空泵vacuum pump指示功率indicated power指示热效率indicated thermal efficiency指示油耗率indicated specific energy consumption示功图indicator diagram冷却系cooling system风冷air cooling水冷water-cooling循环流冷却系cooling recovery system自然循环液冷却系统natural circulation type cooling system热流循环液冷却系统thermo-siphon circulation type cooling system 温差循环液冷却系统gravity circulation water cooling system压力式水冷却系统positive circulation cooling system加压式冷却法pressure type cooling水泵循环冷却系统pump circulation cooling system强制循环式化冷系统forced-feed water circulation system 封闭式液冷系统sealed cooling system散热器radiator片式散热器finned radiator管式散热器tubular radiator蜂窝式散热器cellular radiator哈里逊式散热器Harrison type radiator带板式散热器ribbon type radiator上水箱upper tank下水箱lower tank涨溢箱expansion tank散热器芯radiator core之字形管散热器芯film core管-片式散热器芯fin and tube core散热器加水口盖radiator filter cap压力式水箱盖radiator-pressure cap蒸气-空气泄放阀vapor-air release valve散热器护罩radiator cowl散热器百叶窗radiator shutter散热器保温帘radiator roller blind散热片cooling fin缸盖散热片cylinder head fin缸体散热片cylinder block fin控温装置temperature regulating device恒温器thermostat恒温器主阀thermostat main valve恒温器旁通阀thermostat by-pass valve恒温器挠性波纹筒thermostat flexible bellows液体冷却设备liquid cooling equipment水泵water pump水泵体pump casing水泵叶轮water pump impeller旁通进水口water by-pass inlet neck循环泵circulating pump主进水口water main inlet port出水口water outlet port自调式水封self-adjusting seal unit溢流管overflow pipe导流板deflector风扇fan(blower)轴流式风扇axial flow fan离心式风扇centrifugal fan风扇壳体blower casing风扇导流罩fan cowl风扇毂fan hub风扇叶片fan blade风扇叶轮blower impeller风扇导流定子blower stator风扇皮带轮fan pulley三角皮带v-belt风扇护罩fan shroud风扇叶轮叶片impeller vane冷却用空气cooling air风扇导流叶片stator vane强制风冷forced-air cooling自然风冷natural air cooling风道air ducting润滑系lubrication system润滑lubrication气缸上部润滑upper cylinder lubrication 压力润滑pressure-feed lubrication压力润滑法forced lubrication自动润滑automatic lubrication飞溅润滑splash lubrication润滑周期lubrication interval边界润滑borderline lubrication曲轴箱机油油盘crankcase oil pan油底壳oil pan机油盘放油塞sump plug集油器oil collector机油泵oil pump计量式机油泵metering oil pump齿轮式机油泵gear type oil pump转子式机油泵rotor-type oil pump机油泵出油管oil pump outlet pipe放油口oil drain hole油道oil duct断油开关cut-off cock机油散热器oil cooler机油滤清器oil filter机油粗滤器primary oil filter机油精滤器secondary oil filter全流式机油滤清器full-flow oil filter分流式机油滤清器by-pass oil filter离心式机油滤清器centrifugal oil filter 整体式滤芯integral filtering element细滤器滤芯filter element滤清器壳filter box滤片filtering disc机油减压器oil pressure relief valve旁通阀by-pass oil filter机油滤网oil strainer加机油孔oil filter cap滤芯轴filter shaft刮片组件cleaning edge机油量尺dipstick机油滤网oil strainer增压器supercharger增压和扫气装置pressure-charging and scavenging unit 增压装置supercharging device涡轮增压器turbo-charger气波增压器comprex pressure wave supercharger增压器阻风阀supercharger blast gate增压器调节容气量的旁通阀supercharger control bypass 增压器叶轮supercharger impeller惯性增压inertia supercharging机械增压mechanical supercharging涡轮增压turbo-charging增压比supercharge ratio增压压力boost pressure增压中冷inter-cooling中冷度inter-cooling level增压度supercharging level喘振surge喘振线surge line轴流式涡轮axial-flow turbine脉冲进气ram charging发动机试验engine test发动机试验规程engine test procedure发动机技术要求engine technical requirements标准大气状况standard atmospheric conditions大气压力atmospheric pressure进气温度inlet air temperature进气温度inlet air temperature功率校正power correction功率标定power rating功率换算power conversion校正系数correction factor换算系数performance test性能试验performance test起动性能试验starting ability test怠速试验idle running test道路负荷试验road load test各缸工作均匀性试验cylinder variation test背压试验back pressure test最低稳定工作转速试验lowest continuous speed test with load 背部泄漏试验back-leakage test调整试验adjustment test热平衡试验heat balance test快速磨损试验accelerated wear test热冲击试验thermo-shock test空载特性试验no-load characteristic test模拟增压试验simulated supercharging test停缸试验cylinder fuel-cut test增压机匹配试验turbo-charger matching test排气分析试验exhaust analysis test突变负荷试验sudden load change test稳定性试验stability test单缸熄火试验one cylinder shut off test例行检查试验routine inspection test验证试验verification test鉴定试验approval test可靠性试验reliability test耐久性试验durability test定型试验type approval test验收试验acceptance test现场试验field test出厂试验delivery test抽查试验spot check test复查试验re-check test台架试验bench test强化试验hop-up test发动机试验台engine test bed底盘测功机chassis dynamometer测功机dynamometer水力测功机hydraulic dynamometer电涡流测功机eddy current dynamometer电力测功机electric dynamometer扭矩仪torque meter转速表tachometer温度测量thermometry温度测量仪器thermometric instruments空气流量测量air flow measurement热线风速仪hot wire anemometer电子示功仪electronic indicator燃烧分析仪combustion analyzer压力传感器pressure transducer精密声级计precision sound level meter排放emission排放物emission排气污染物gaseous pollutant蒸发排放物evaporative emission曲轴箱排放物crankcase emission漏气blowby gas氨氧化物oxids of nitrogen一气化碳carbon monoxide碳氢化合物hydrocarbon甲烷methane无甲烷碳氢化合物non-methane hydrocarbons光化学活性碳氢化合物photochemically reactive hydrocarbons 微粒物particulated matter黑烟black smoke蓝烟blue smoke白烟white smoke碳烟soot光化学烟雾smog臭味odor丙烷propane排放浓度concentration of emission排气烟度exhaust smoke先期排气initial exhaust亚临界排气subcritical exhaust超临界排气supercritical exhaust强制排气forced exhaust自由排气free exhaust排气提前角exhaust advance angle排气迟后角exhaust lag angle排气热损失exhaust heat loss排气净化exhaust purification排气背压exhaust back pressure残余废气residual gas排气有害成分poisonous exhaust composition柴油机排烟diesel smoke综合排放浓度composite concentration of exhaust emission综合排放质量composite mass of exhaust emission排放系数emission factor排放率emission index质量排放量mass emission比排放量brake specific emission排放物控制系统emission control system排气排放物控制系统exhaust emission control system二次空气secondary air二次空气分配歧管secondary air distribution二次空气控制阀secondary air control valve二次空气转换阀secondary air switching valve。
汽车英文专业词汇
汽车专业英语词汇汽车automobile拖拉机 tractor铁路机车locomotive有轨电车tram无轨电车trolley军用车辆 military vehicle蒸汽机steam engine煤气机gas engine汽油机gasoline engine国民经济national economy国内生产总值 (GDP) Gross Domestic Production 全拆散 (CKD) Completely Knock Down半拆散 (SKD) Semi-Knock Down改革开放 reform and opening技术引进technical import国产化 localization支柱产业pillar estate轿车car客车 bus, coach货车truck, lorry公路用车road vehicle非公路用车off-road vehicle发动机 engine机体engine body曲柄连杆机构 crank-connecting rod mechanism 配气机构valve timing mechanism供给系fuel supply system冷却系cooling system润滑系lubricating system点火系ignition system起动系starting system底盘chassis传动系power train离合器clutch变速器gear box传动轴propeller shaft驱动桥drive axle行驶系running gear车架frame悬架 suspension前轴 front axle桥壳 axle housing车轮 wheel转向系 steering system转向盘 steering wheel转向器 steering gear转向传动装置steering linkage助力装置power assisting device制动系braking system控制装置 control device供能装置 power supply device传动装置 transfer device制动器 brake车身body车前板制件 front end panels车身壳体 body shell车门 door车窗 window附属装置 auxiliary device货箱 carrying platform发动机前置后轮驱动 (FR) front engine rear drive 发动机前置前轮驱动(FF) front engine front drive 发动机后置后轮驱动(RR) rear engine rear drive发动机中置后轮驱动 (MR) midship engine rear drive 全轮驱动 (AWD) all wheel drive驱动力 tractive force阻力 resistance滚动阻力 rolling resistance空气阻力 air resistance, drag上坡阻力 gradient resistance附着作用 adhesion附着力 adhesive force附着系数 coefficient of adhesion 第一章发动机工作原理二冲程发动机two stroke engine四冲程发动机four stroke engine 水冷发动机water cooled engine风冷发动机air cooled engine上止点(UDP) upper dead point下止点(LDP) lower dead point活塞行程stroke汽缸直径bore工作容积working volume排量swept volume, displacement 进气行程intake stroke压缩行程compression stroke压缩比compression ratio做功行程working stroke爆燃，敲缸 detonation, knock排气行程 exhaust stroke示功图indicating diagram汽缸体 cylinder block汽缸盖cylinder head油底壳oil sump活塞piston连杆connecting rod曲轴crankshaft飞轮flywheel进气门intake valve排气门exhaust valve挺柱tappet推杆push rod摇臂rocker凸轮轴camshaft正时齿轮timing gear燃油箱fuel tank燃油泵fuel pump汽油滤清器gasoline filter 化油器carburetor空气滤清器air cleaner进气管 intake manifold排气管 exhaust manifold火花塞 spark plug点火线圈 ignition coil断电器 breaker蓄电池 storage battery发电机generator水泵 water pump散热器radiator风扇fan放水阀 drain valve水套 water jacket分水管 distributive pipe机油泵 oil pump集滤器 suction filter限压阀 relief valve润滑油道 oil passage机油滤清器 oil filter机油冷却器oil cooler起动机 starting motor有效功率 effective power有效转矩 effective torque燃油消耗率 specific fuel consumption发动机转速特性 engine speed characteristic 节气门开度 throttle percentage部分特性 partial characteristic外特性 outer characteristic第二章曲柄连杆机构汽缸套cylinder sleeve, cylinder liner发动机支承 engine mounting活塞顶 piston top活塞头部 piston head活塞裙 piston skirt开槽 slot活塞环 piston ring气环 compression ring油环 oil ring环槽 groove活塞销 piston pin主轴承 main bearing主轴承盖 main bearing cap主轴瓦 main shell连杆轴承 big end bearing连杆盖 big end cap起动爪 cranking claw带轮 pulley平衡重 counter weight发火顺序 firing order扭振减振器 torsional vibration damper第三章配气机构顶置气门 (OHV) Over Head Valve顶置凸轮轴 (OHC) Over Head Camshaft单顶置凸轮轴 (SOHC) Single Over Head Camshaft 双顶置凸轮轴 (DOHC) Dual Over Head Camshaft多气门发动机 multi-valve engine气门间隙 valve clearance配气相位 timing phase气门杆 valve stem气门座 valve seat气门导管 valve guide气门弹簧 valve spring第四章汽油机供给系可燃混合气 combustion mixture消声器 silencer, muffler汽油 gasoline, petrol分馏 distil蒸发性 evaporating property热值 heat value抗爆性anti-knock property辛烷值 (RON) Research Octane Number过量空气系数 coefficient of excessive air 理论混合气 theoretical mixture稀混合气 thin mixture浓混合气 thick mixture主供油系统 main supply system怠速系统 idle system加浓系统 thickening system加速系统 accelerating system浮子 float浮子室 float chamber针阀 needle valve量孔metering jet阻风门 choke滤芯 filter cartridge沉淀杯sediment cup泵膜 pump diaphragm油浴式 oil bath type石棉垫 a**estos pad预热pre-heating汽油直接喷射 gasoline direct injection 电控 electronic control多点喷射muti-point injection单点喷射 single point injection电路控制circuit control分电器信号 distributor signal空气流量信号airflow signal冷却水温信号 water temperature signal 第五章柴油机供给系输油泵 transfer pump喷油泵 fuel injection pump高压油管 high pressure fuel pipe发火性 ignition property黏度viscosity凝点 condensing point备燃期 pri-combustion period速燃期 rapid combustion period缓燃期 slow combustion period统一燃烧室 united chamber球形燃烧室ball shape chamber涡流室 turbulence chamber预燃室pri-combustion chamber喷油器 injector精密偶件 precise couple柱塞plunger出油阀delivery valve调速器governor两速调速器two speed governor全速调速器full speed governor定速调速器fixed speed governor综合调速器combined governor气动调速器pneumatic governor机械离心式调速器mechanical centrifugal governor 复合式调速器complex governor喷油提前角调节装置advancer飞块flyweight联轴节coupling粗滤清器primary filter细滤清器secondary filter涡轮增压器turbocharger中间冷却器intermediate cooler第七章冷却系节温器 thermostat防冻液 anti-freezing liquid补偿水桶 compensation reservoirV-带 V belt百叶窗 shutter大循环 big circulation小循环 small circulation散热翅片 fins第八章润滑系润滑剂 lubricant压力润滑 pressure lubrication飞溅润滑splash lubrication润滑脂grease机油压力传感器 oil pressure sensor 油封 oil seal旁通阀 bypass valve机油散热器 oil cooler机油尺 dip stick加机油口oil filler曲轴箱通风 crankcase ventilation 第九章点火系一次绕组primary winding二次绕组 secondary winding热敏电阻heat sensitive resistance点火提前ignition advance分电器distributor活动触点moving contact固定触点fixed contact分火头distributor rotor arm电容器condenser点火提前装置ignition advancer离心式点火提前装置centrifugal ignition advancer 真空式点火提前装置vacuum ignition advancer辛烷值校正器octane number rectifier中心电极central electrode侧电极side electrode瓷绝缘体ceramic insulator跳火间隙spark gap半导体点火系semi-conductor ignition system晶体管 transistor二极管diode三极管triode无触点点火系non-contact ignition system霍尔效应 Hall effect正极板 anode负极板cathode隔板separator电解液electrolyte蓄电池格battery cell接线柱 terminal电缆cable硅整流交流发电机silicon rectified A.C. motor 转子 rotor定子stator电刷 brush风扇叶轮 fan blade电压调节器voltage regulator第十章起动系手摇起动cranking电热塞 electric heater plug串激直流发电机 serial wound D.C. motor起动齿圈starter ring电磁操纵机构electro-magnetic control第十一章新型发动机三角活塞triangular piston转子发动机 rotary engine自转 rotary motion, rotation公转 orbit motion轨迹 trajectory齿轮 gear齿圈 ring gear往复零件 reciprocal parts动平衡dynamic balance燃气涡轮发动机 gas turbine第十二章汽车传动系机械式传动系 mechanical transmission液力机械式传动系 hydro-mechanical transmission静液式传动系 static-hydraulic transmission电力式传动系electrical transmission自动式传动系automatic transmission减速 reduction可变速比variable ratios有级变速definite ratios无级变速indefinite ratios无级变速器(CVT) Continuously Variable Transmission 一般布置general layout发动机横置 lateral engine positioning分动器 transfer case, transfer box第十三章离合器接合柔和 smooth engagement分离彻底 thorough separation过载 overload摩擦表面 friction surface摩擦衬片 friction liner毂 hub主动部分 driving part从动部分 driven part花键 spline压盘 pressure plate离合器盖 cover plate分离杠杆 release lever分离套筒 release sleeve分离轴承 release bearing主缸 master cylinder工作缸 working cylinder分离叉 release fork间隙调整 clearance adjustment打滑 slip踏板 pedal踏板自由行程 pedal free stroke踏板工作行程 pedal working stroke铆钉，铆接 rivet双片离合器 dual disc clutch中央弹簧离合器central spring clutch膜片弹簧离合器 diaphragm spring clutch 非线性 non-linear第十四章变速器与分动器输入轴（第一轴）input shaft, drive shaft 输出轴（第二轴）output shaft, main shaft 中间轴 counter shaft倒挡轴reverse gear shaft常啮合 constant mesh低速挡 low gear高速挡 high gear最高速挡 top gear空挡 neutral gear一挡 the first gear二挡 the second gear三挡 the third gear倒挡 reverse gear直接挡 direct gear超速挡 overdrive动力输出 power take-off换挡 shift啮合套 sliding sleeve同步器 synchronizer同步锥面 synchro cone变速杆 shifting lever手柄 handle球铰链 ball joint换挡拨叉 shifting fork自锁 self-lock互锁 inter-lock变速驱动桥 transaxle加力挡 low gear第十五章液力机械传动液力偶合器hydraulic coupling泵轮 impeller涡轮 turbine叶片 blade液力变矩器 torque converter导轮 stator行星齿轮系 planetary gear system 太阳轮 sun gear行星轮 planet pinion行星架 planet carrier齿圈 ring gear万向节 universal joint, U-joint十字轴式万向节Cardan type U-joint 叉子 yoke, fork十字轴 spider, center cross滚针轴承 needle bearing滑脂嘴（油嘴）lubricating fitting, nipple等角速 constant angular velocity双联式万向节 dual Cardan type U-joint球叉式万向节 Weiss type U-joint球笼式万向节 Rzeppa type U-joint星形套 inner race housing球形壳 outer race shell保持架，球笼 retainer, ball cage挠性万向节 flexible U-joint无缝钢管 seamless steel tube第十七章驱动桥主减速器 final drive主动（小）齿轮 drive pinion从动（大）齿轮 ring gear伞齿轮 bevel gear双曲面齿轮 hypoid gear单级减速 single reduction双级减速 double reduction贯通式主减速器 penetrable final drive双速主减速器 double gear (speed) final drive 轮边减速器 wheel reduction差速器 differential半轴齿轮 differential side gear差速锁 differential lock轴间差速器 inter-axle differential lock托森差速器 torque sensitive differential。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
低速档
bottom gear(low speed gear)
超速档
overdrive gear
经济档
economic gear
倒档
reverse gear
万向节
universal joint
十字轴式万向节
carton(hooks)universal joint
球销式万向节
桥壳
axle housing
半轴
axle shaft
全浮式半轴
full-floating axle shaft
半浮式半轴
semi-floating axle shaft
悬架
suspension
非独立悬架
rigid axle suspension
独立悬架
independent suspension
四连杆式
变速器输出轴
transmission output shaft
变速齿轮比（变速比）
transmission gear ratio
传动比
gear ratio
换档
Shift
换档机构
gearshift
操纵杆
control lever
空档位置
neutral position
直接驱动
direct drive
高速档
displacement
发动机排量
engine displacement
气缸容量
cylinder capacity
压缩比
compression ratio
空燃比
air fuel ratio
扭矩
torque
输出马力
shaft horsepower
总功率
gross power
燃油消耗量
fuel consumption
定钳盘式制动器
disc brake with fixed caliper
浮钳盘式制动器
disc brake with floating caliper
浮盘式制动器
floating disc brake
全盘式制动器
complete disc brake
凸轮张开式制动器
cam brake
楔式制动器
wedge brake
车架
auxiliary tank
整体车架
unitized frame
车轮
wheel
轮辋
rim
轮胎
tyre(tire)
速度符号
speed symbol
外胎
cover
内胎
inner tube
子午线轮胎
radial ply tyre
胎面花纹
tread pattern
胎冠
crown
胎面
tread
转向系
steering system
总效率
overall efficiency
机械效率
mechanical efficiency
发动机转速
engine speed(rotational frequency)
怠速转速
idling speed
最低稳定工作转速
lowest continuous speed with load
最大扭矩转速
speed at maximum torque
四冲程发动机
four-stroke engine
直接喷射式柴油机
direct injection engine
增压式发动机
supercharged engine
风冷式发动机
air-cooled engine
油冷式发动机
oil-cooled engine
水冷式发动机
water-cooled engine
flexible member assembly
球笼式万向节
repel universal joint
驱动桥
drive axle(driving axle)
减速器
reducer
主Байду номын сангаас速器
final drive
差速器
differential
行星齿轮
spider gear(planetary pinion)
促动管路
control line
操纵管路
pilot line
制动管路
braking line
电缆或导线
cable or wire
制动器
brake
摩擦式制动器
fraction brake
鼓式制动器
drum brake
盘式制动器
disc brake
双领蹄式制动器
two leading shoe brake
轮缸式制动器
wheel cylinder brake
手制动器
hand brake
领蹄（紧蹄）
primary shoe(leading shoe)
从蹄（松蹄）
secondary shoe(trailing shoe)
进气消声器
intake silencer
排气管
exhaust pipe
车轮防抱死装置
anti-lock device
传感器
sensor
控制器
controller
调节器
modulator
限压阀
pressure limiting valve
比例阀
proportioning valve
限位装置
inhibiting device
安全缸
safety cylinder
制动灯开关
braking light switch
分离开关
连杆
connecting rod
曲轴
crankshaft
整体式曲轴
one-piece crankshaft
组合式曲轴
assembled crankshaft
曲柄
crank
飞轮
flywheel
配气机构
valve gear
凸轮轴
camshaft
凸轮
cam
变速器输入轴
transmission input shaft
驻车制动系统
parking braking system
总制动距离
total braking distance
有效制动距离
active braking distance
制动力
braking work
停车距离（制动距离）
stopping distance
驾驶员反应时间
reaction time of driver
工作循环
working cycle
冲程
stroke
活塞行程
piston stroke
进气行程
charging stroke
压缩行程
compression stroke
膨胀行程
expansion stroke
排气行程
exhaust stroke
止点
dead center
缸径
cylinder bore
排气量
自然进气式发动机
naturally aspirated engine
多种燃料发动机
multifuel engine
双燃料发动机
duel fuel engine
多气缸发动机
multiple cylinder engine
直列式发动机
in-line engine
前置式发动机
front-engine
后置式发动机
遮阳板
sun visor
随车工具
tool box
钢化玻璃
toughened grass
全天候空调系统
full range A/C
防滑地板
no-skid floor
爬坡能力
grade ability
怠速时
at idle
消音器
muffler
镀锌板
galvanized plate
空气导流板
air deflector
双从蹄式制动器
two trailing shoe brake
双向双领蹄式制动器
dual two leading shoe brake
双向双从蹄式制动器
dual two trailing shoe brake
领从蹄式制动器
leading trailing shoe brake
钳盘式制动器
caliper disc brake
逆时针
counter-clockwise
气缸体和气缸盖
cylinder block and head
整体铸造
cast in block(cast unlock)
发动机罩
engine bonnet
气缸
cylinder
缸径
cylinder bore
气缸套
cylinder liner(cylinder sleeve)
手制动杆
hand lever
弹簧座
spring seat
助力器
booster
真空助力器
vacuum booster
管路
pipe-line
传能管路
energy transmission lines
供能管路
energy transmission lines
供给管路
feed pipe
控制管路
supply line