SJB黄色弹簧-ISO10243国际标准模具弹簧规格表
模具弹簧规格及参数
模具彈簧规格及参数一.彈簧功能彈簧是模具中廣泛應用的彈性零件,主要用于卸料、壓料、推件和頂出等工作.根據荷重不同,共分五種不同顏色加以區分,易於判別和選用.二.規格系列1.彈簧外徑系列: Φ6Φ8,Φ10,Φ12,Φ14,Φ16,Φ18,Φ20,Φ22,Φ25,Φ30,Φ35,Φ40,Φ50等.2.種類3.彈簧長度：15<=L<=80MM時,每5MM為一個階;80=<L<=100MM時,每10MM為一個階;L>=100MM時,每25MM為一個階.4.扁线彈簧最小直径6mm5.彈簧內徑等于彈簧外徑的二分之一.6.相同直径颜色的弹簧，不管自由长度是多长，压40％产生的力一样结论：相同直径颜色的弹簧，自由长度越短，压缩1mm产生的力越大7.通常使用的最大壓縮比是彈簧使用30萬次的最大壓縮比.汽车模具使用50萬次的最大壓縮比..8.弹簧能压缩的长度=弹簧的自由长度x弹簧的压缩比例：Φ20绿色弹簧长度50mm，弹簧要求寿命30万次，弹簧能压缩多长？50x24％=12(mm)9.弹簧的长度=弹簧要压缩的长度÷弹簧的压缩比例：弹簧要压缩20mm, 弹簧颜色为红色，弹簧要求寿命50万次要用多长的弹簧？弹簧的长度=20÷28.8％+5MM=74.4 查表选用75MM长弹簧一般选弹簧长度会加5mm的安全余量三.選用原則1.長度選擇一般保証:在開模狀態彈簧的預壓縮量等於3~5(常规预压3mm,預壓縮量隨實際情況而定.);閉模狀態彈簧壓縮量小於或等於最大壓縮量(最大壓縮量LA=彈簧自由長L*最大壓縮比取值%).2.模板压料，脱料板压料優先選用綠色或棕色（茶色，咖啡色)彈簧;如果向上成形的下模压料，折弯脱料所需的頂料力不很大時,可選用紅色,绿色彈簧，浮料用黄色，圆线弹簧.3.復合模外脫料板用紅色彈簧,內脫料板用綠色或棕色彈簧.4.活動定位銷一般選用Φ6頂料銷,配Φ10黃色彈簧和M12止付螺絲.Φ8頂料銷,配Φ12黃色彈簧和M14止付螺絲.5.沖孔模和成形模用綠色或棕色（茶色，咖啡色)彈簧,如有特殊需求時,由專案主管確定.6.彈簧規格優先選用Φ30.在空間較小區域可考慮選用其它規格(如Φ25,Φ20,Φ18,Φ16…...等).Φ25的内导柱用Φ30的弹簧脱料Φ20的内导柱用Φ25的弹簧脱料四.排配原則1.彈簧過孔中心到模板邊緣距離大於外徑D,與其他孔距離保持實體壁厚大於5MM,空间不足时最少留2MM.2.彈簧排列首先考慮受力重點部位,然後再考慮整個模具受力均衡平穩.受力重點部位是指:復合模的內脫料板外形和沖頭的周圍;沖孔模的沖頭周圍;成形模的折彎邊及有抽成形的地方.3.成形模采用氣墊結構時,下打板排配2~6個彈簧.下模座上不沉孔,彈簧選用黃色或藍色即可.五.五金零件需求表填寫範例彈簧(顏色):D*L (D-彈簧外徑L-自由長度)例: 彈簧TH(綠): Φ20*70Welcome To Download !!!欢迎您的下载，资料仅供参考！。
模具弹簧规格及参数
模具弹簧规格及参数 Document serial number【KKGB-LBS98YT-BS8CB-BSUT-BST108】模具弹簧规格及参数一. 弹簧功能弹簧是模具中广泛应用的弹性零件,主要用于卸料、压料、推件和顶出等工作.根据荷重不同,共分五种不同颜色加以区分,易於判别和选用.二. 规格系列1.弹簧外径系列: Φ6Φ8,Φ10,Φ12,Φ14,Φ16,Φ18,Φ20,Φ22,Φ25,Φ30,Φ35,Φ40,Φ50等.2.种类3.弹簧长度：15<=L<=80MM时,每5MM为一个阶;80=<L<=100MM时,每10MM为一个阶;L>=100MM时,每25MM为一个阶.4.扁线弹簧最小直径6mm5.弹簧内径等于弹簧外径的二分之一.6.相同直径颜色的弹簧，不管自由长度是多长，压40％产生的力一样结论：相同直径颜色的弹簧，自由长度越短，压缩1mm产生的力越大7.通常使用的最大压缩比是弹簧使用30万次的最大压缩比.汽车模具使用50万次的最大压缩比..8.弹簧能压缩的长度=弹簧的自由长度x弹簧的压缩比例：Φ20绿色弹簧长度50mm，弹簧要求寿命30万次，弹簧能压缩多长50x24％=12(mm)9.弹簧的长度=弹簧要压缩的长度÷弹簧的压缩比例：弹簧要压缩20mm, 弹簧颜色为红色，弹簧要求寿命50万次要用多长的弹簧弹簧的长度=20÷％+5MM= 查表选用75MM长弹簧一般选弹簧长度会加5mm的安全余量10.弹簧要压缩的长度=活动板行程+3~5mm预压 (常规预压3mm)11.弹簧模板孔的大小直径<20模板孔=D+1直径>=20模板孔=D+2三. 选用原则1.长度选择一般保证:在开模状态弹簧的预压缩量等於3~5(常规预压3mm,预压缩量随实际情况而定.);闭模状态弹簧压缩量小於或等於最大压缩量(最大压缩量LA=弹簧自由长L*最大压缩比取值%).2.模板压料，脱料板压料优先选用绿色或棕色（茶色，咖啡色)弹簧;如果向上成形的下模压料，折弯脱料所需的顶料力不很大时,可选用红色,绿色弹簧，浮料用黄色，圆线弹簧.3.复合模外脱料板用红色弹簧,内脱料板用绿色或棕色弹簧.4.活动定位销一般选用Φ6顶料销,配Φ10黄色弹簧和M12止付螺丝.Φ8顶料销,配Φ12黄色弹簧和M14止付螺丝.5.冲孔模和成形模用绿色或棕色（茶色，咖啡色)弹簧,如有特殊需求时,由专案主管确定.6.弹簧规格优先选用Φ30.在空间较小区域可考虑选用其它规格(如Φ25,Φ20,Φ18,Φ16…...等).Φ25的内导柱用Φ30的弹簧脱料Φ20的内导柱用Φ25的弹簧脱料四. 排配原则1.弹簧过孔中心到模板边缘距离大於外径D,与其他孔距离保持实体壁厚大於5MM,空间不足时最少留2MM.2.弹簧排列首先考虑受力重点部位,然後再考虑整个模具受力均衡平稳.受力重点部位是指:复合模的内脱料板外形和冲头的周围;冲孔模的冲头周围;成形模的折弯边及有抽成形的地方.3.成形模采用气垫结构时,下打板排配2~6个弹簧.下模座上不沉孔,弹簧选用黄色或蓝色即可.五. 五金零件需求表填写范例弹簧(颜色):D*L (D-弹簧外径 L-自由长度)例: 弹簧TH(绿): Φ20*70。
模具弹簧规格与参数
模具彈簧规格及参数一.彈簧功能彈簧是模具中廣泛應用的彈性零件,主要用于卸料、壓料、推件和頂出等工作.根據荷重不同,共分五種不同顏色加以區分,易於判別和選用.二.規格系列1.彈簧外徑系列:Φ6Φ8,Φ10,Φ12,Φ14,Φ16,Φ18,Φ20,Φ22,Φ25,Φ30,Φ35,Φ40,Φ50等.彈簧外徑D Φ8 Φ10 Φ12 Φ14 Φ16 Φ18 Φ20 Φ22 Φ25 Φ30 Φ35 Φ40 Φ50 過孔直徑D1 Φ8.5 Φ10.5 Φ12.5 Φ14.5 Φ17.0 Φ19.0 Φ21.0 Φ23.0 Φ26.0 Φ32.0 Φ37.0 Φ42.0 Φ52.0 上模座沉孔直徑D2 Φ12.0 Φ14.0 Φ16.0 Φ18.0 Φ20.0 Φ23.0 Φ26.0 Φ26.0 Φ30.0 Φ35.0 Φ40.0 Φ45.0 Φ55.0長度L彈簧TF (黃) ╳20~80 20~80 25~90 25~100 25~100 25~125 ╳25~150 25~175 40~200 50~250 60~300 彈簧TL (藍) ╳20~80 20~80 25~90 25~100 25~100 25~125 ╳25~150 25~175 40~200 50~250 60~300 彈簧TM (紅) 15~60 20~60 20~60 25~70 25~80 25~90 25~100 25~125 25~125 25~175 45~200 50~250 60~300 彈簧TH (綠) 15~60 20~60 20~60 25~70 25~80 25~90 25~100 25~125 25~125 25~175 40~200 50~250 60~300 彈簧TB (棕) 15~60 20~80 20~80 25~90 25~100 25~100 25~100 25~125 25~125 25~175 40~200 50~250 60~300 2.種類種類顏色最大極限壓縮比30万回最大壓縮比50万回最大壓縮比100万回最大壓縮比輕小荷重黃色58% 50% 45% 40%輕荷重藍色48% 40% 36% 32%中荷重紅色38% 32% 28.8% 25.6%重荷重綠色28% 24% 21.6% 19.2%極重荷重棕色（茶色，咖啡色)24% 20% 18% 16%3.彈簧長度：15<=L<=80MM時,每5MM為一個階;80=<L<=100MM時,每10MM為一個階;L>=100MM時,每25MM為一個階.4.扁线彈簧最小直径6mm5.彈簧內徑等于彈簧外徑的二分之一.6.相同直径颜色的弹簧，不管自由长度是多长，压40％产生的力一样结论：相同直径颜色的弹簧，自由长度越短，压缩1mm产生的力越大7.通常使用的最大壓縮比是彈簧使用30萬次的最大壓縮比.汽车模具使用50萬次的最大壓縮比..8.弹簧能压缩的长度=弹簧的自由长度x弹簧的压缩比例：Φ20绿色弹簧长度50mm，弹簧要求寿命30万次，弹簧能压缩多长？50x24％=12(mm)9.弹簧的长度=弹簧要压缩的长度÷弹簧的压缩比例：弹簧要压缩20mm, 弹簧颜色为红色，弹簧要求寿命50万次要用多长的弹簧？弹簧的长度=20÷28.8％+5MM=74.4 查表选用75MM长弹簧一般选弹簧长度会加5mm的安全余量10.弹簧要压缩的长度=活动板行程+3~5mm预压(常规预压3mm)11.弹簧模板孔的大小直径<20模板孔=D+1直径>=20模板孔=D+2DD1D2三.選用原則1.長度選擇一般保証:在開模狀態彈簧的預壓縮量等於3~5(常规预压3mm,預壓縮量隨實際情況而定.);閉模狀態彈簧壓縮量小於或等於最大壓縮量(最大壓縮量LA=彈簧自由長L*最大壓縮比取值%).2.模板压料，脱料板压料優先選用綠色或棕色（茶色，咖啡色)彈簧;如果向上成形的下模压料，折弯脱料所需的頂料力不很大時,可選用紅色,绿色彈簧，浮料用黄色，圆线弹簧.3.復合模外脫料板用紅色彈簧,內脫料板用綠色或棕色彈簧.4.活動定位銷一般選用Φ6頂料銷,配Φ10黃色彈簧和M12止付螺絲.Φ8頂料銷,配Φ12黃色彈簧和M14止付螺絲.5.沖孔模和成形模用綠色或棕色（茶色，咖啡色)彈簧,如有特殊需求時,由專案主管確定.6.彈簧規格優先選用Φ30.在空間較小區域可考慮選用其它規格(如Φ25,Φ20,Φ18,Φ16…...等).Φ25的内导柱用Φ30的弹簧脱料Φ20的内导柱用Φ25的弹簧脱料四.排配原則1.彈簧過孔中心到模板邊緣距離大於外徑D,與其他孔距離保持實體壁厚大於5MM,空间不足时最少留2MM.2.彈簧排列首先考慮受力重點部位,然後再考慮整個模具受力均衡平穩.受力重點部位是指:復合模的內脫料板外形和沖頭的周圍;沖孔模的沖頭周圍;成形模的折彎邊及有抽成形的地方.3.成形模采用氣墊結構時,下打板排配2~6個彈簧.下模座上不沉孔,彈簧選用黃色或藍色即可.五.五金零件需求表填寫範例彈簧(顏色):D*L (D-彈簧外徑L-自由長度) 例: 彈簧TH(綠): Φ20*70。
模具弹簧规格及参数
模具弹簧规格及参数 Company number：【0089WT-8898YT-W8CCB-BUUT-202108】模具弹簧规格及参数一.弹簧功能弹簧是模具中广泛应用的弹性零件,主要用于卸料、压料、推件和顶出等工作.根据荷重不同,共分五种不同颜色加以区分,易於判别和选用.二.规格系列1.弹簧外径系列:Φ6Φ8,Φ10,Φ12,Φ14,Φ16,Φ18,Φ20,Φ22,Φ25,Φ30,Φ35,Φ40,Φ50等.2.种类3.弹簧长度：15<=L<=80MM时,每5MM为一个阶;80=<L<=100MM时,每10MM为一个阶;L>=100MM时,每25MM为一个阶.4.扁线弹簧最小直径6mm5.弹簧内径等于弹簧外径的二分之一.6.相同直径颜色的弹簧，不管自由长度是多长，压40％产生的力一样结论：相同直径颜色的弹簧，自由长度越短，压缩1mm产生的力越大7.通常使用的最大压缩比是弹簧使用30万次的最大压缩比.汽车模具使用50万次的最大压缩比..8.弹簧能压缩的长度=弹簧的自由长度x弹簧的压缩比例：Φ20绿色弹簧长度50mm，弹簧要求寿命30万次，弹簧能压缩多长50x24％=12(mm)9.弹簧的长度=弹簧要压缩的长度÷弹簧的压缩比例：弹簧要压缩20mm, 弹簧颜色为红色，弹簧要求寿命50万次要用多长的弹簧弹簧的长度=20÷％+5MM= 查表选用75MM长弹簧一般选弹簧长度会加5mm的安全余量10.弹簧要压缩的长度=活动板行程+3~5mm预压 (常规预压3mm)11.弹簧模板孔的大小直径<20模板孔=D+1直径>=20模板孔=D+2三.选用原则1.长度选择一般保证:在开模状态弹簧的预压缩量等於3~5(常规预压3mm,预压缩量随实际情况而定.);闭模状态弹簧压缩量小於或等於最大压缩量(最大压缩量LA=弹簧自由长L*最大压缩比取值%).2.模板压料，脱料板压料优先选用绿色或棕色（茶色，咖啡色)弹簧;如果向上成形的下模压料，折弯脱料所需的顶料力不很大时,可选用红色,绿色弹簧，浮料用黄色，圆线弹簧.3.复合模外脱料板用红色弹簧,内脱料板用绿色或棕色弹簧.4.活动定位销一般选用Φ6顶料销,配Φ10黄色弹簧和M12止付螺丝.Φ8顶料销,配Φ12黄色弹簧和M14止付螺丝.5.冲孔模和成形模用绿色或棕色（茶色，咖啡色)弹簧,如有特殊需求时,由专案主管确定.6.弹簧规格优先选用Φ30.在空间较小区域可考虑选用其它规格(如Φ25,Φ20,Φ18,Φ16…...等).Φ25的内导柱用Φ30的弹簧脱料Φ20的内导柱用Φ25的弹簧脱料四.排配原则1.弹簧过孔中心到模板边缘距离大於外径D,与其他孔距离保持实体壁厚大於5MM,空间不足时最少留2MM.2.弹簧排列首先考虑受力重点部位,然後再考虑整个模具受力均衡平稳.受力重点部位是指:复合模的内脱料板外形和冲头的周围;冲孔模的冲头周围;成形模的折弯边及有抽成形的地方.3.成形模采用气垫结构时,下打板排配2~6个弹簧.下模座上不沉孔,弹簧选用黄色或蓝色即可.五.五金零件需求表填写范例弹簧(颜色):D*L (D-弹簧外径 L-自由长度)例: 弹簧TH(绿): Φ20*70。
模具弹簧规格表
模具弹簧规格表矩形截面模具弹簧（简称模具弹簧）主要用于冲压模、金属压铸模、塑料注射模以及结构精密的机械设备等。
模具弹簧主要选用50CrV A。
它具有安装体积小、弹性好、刚度大、精密度高、制作材料呈矩形及表面分色喷涂（镀），外表美观等特点。
我公司目前标准化产品主要参照日标B5012（较小荷重、轻荷重、中荷重、重荷重、超重荷重）,美国联合标准（中荷重、中等荷重、重荷重、超重荷重）,美国ISO标准（轻荷重、中荷重、重荷重、超重荷重），德标ISO10243（1S、2S、3S、4S、5S）等数千种规格，供用户选用。
模具弹簧规格表请参阅:KF较小荷重KL轻荷重KM中荷重KH重荷重KB超重荷重模具弹簧使用次数和压缩比的关系使用100万次使用50万次使用30万次色别(压缩比:占自由高度的%)荷重种类较小40.045.050.0黄色Yellow 轻32.036.040.0蓝色Blue 中25.628.832.0红色Red 重19.221.624.0绿色Green 超重16.018.0棕色Brown模具弹簧几何尺寸及负荷公差外径D(mm)内径D(mm)自由高度H0≤50(mm)自由高度H0≥50（mm）负荷P N（N）旋向0.0+0.7±0.5±10%H0±10%P N右-0.7+0.1模具弹簧最大压缩量种类最大压缩度较小荷重自由高度×58％轻荷重自由高度×48％中荷重自由高度×38％重荷重自由高度×28％超重荷重自由高度×24％模具弹簧订货方法模具弹簧规格表-KF较小荷重KF轻小荷重LIGHTESTLOAD产品编号外径OuterDia.(mm)内径InnerDia.(mm)自由长FreeLength(mm)定数SpringConst.(kgf/mm)30万0.3million50万0.5million100万1million压缩量(mm)荷重(kgf)压缩量(mm)荷重(kgf)压缩量(mm)荷重(kgf)KF08x158415 1.077.586.876.0620200.8010.09.08.0 25250.6412.511.310.0 30300.5315.013.512.0 35350.4617.515.814.0 40400.4020.018.016.0 45450.3622.520.318.0 50500.3225.022.520.0 55550.2927.524.822.0 60600.2730.027.024.0KF10x2010520 1.0010.0109.098.0825250.8012.511.310.0 30300.6715.013.512.0 35350.5717.515.814.0 40400.5020.018.016.0 45450.4422.520.318.0 50500.4025.022.520.0 55550.3627.524.822.060600.3330.027.024.0KF12x2012620 1.4010.0149.0138.0112525 1.1212.511.310.0 30300.9315.013.512.0 35350.8017.515.814.0 40400.7020.018.016.0 45450.6222.520.318.0 50500.5625.022.520.0 55550.5127.524.822.0 60600.4730.027.024.0KF14x2514725 1.4412.51811.31610.0143030 1.2015.013.512.0 3535 1.0317.515.814.0 40400.9020.018.016.0 45450.8022.520.318.0 50500.7225.022.520.0 55550.6527.524.822.0 60600.6030.027.024.0 65650.5532.529.326.0 70700.5135.031.528.0KF16x2516825 1.6812.52111.31910.0173030 1.4015.013.512.0 3535 1.2017.515.814.0 4040 1.0520.018.016.0 45450.9322.520.318.0 50500.8425.022.520.0 55550.7627.524.822.0 60600.7030.027.024.0 65650.6532.529.326.070700.6035.031.528.0 75750.5637.533.830.0 80800.5240.036.032.0KF18x2518925 2.0812.52611.32310.0213030 1.7315.013.512.0 3535 1.4917.515.814.0 4040 1.3020.018.016.0 4545 1.1622.520.318.0 5050 1.0425.022.520.0 55550.9527.524.822.0 60600.8730.027.024.0 65650.8032.529.326.0 70700.7435.031.528.0 75750.6937.533.830.0 80800.6540.036.032.0 90900.5845.040.536.0KF20x25201125 2.5612.53211.32910.0263030 2.1315.013.512.0 3535 1.8317.515.814.0 4040 1.6020.018.016.0 4545 1.4222.520.318.0 5050 1.2825.022.520.0 5555 1.1627.524.822.0 6060 1.0730.027.024.0 65650.9832.529.326.0 70700.9135.031.528.0 75750.8537.533.830.0 80800.8040.036.032.0 90900.7145.040.536.01001000.6450.045.040.0 1251250.5162.556.350.0KF22x25221125 3.2012.54011.33610.0323030 2.6715.013.512.0 3535 2.2917.515.814.0 4040 2.0020.018.016.0 4545 1.7822.520.318.0 5050 1.6025.022.520.0 5555 1.4527.524.822.0 6060 1.3330.027.024.0 6565 1.2332.529.326.0 7070 1.1435.031.528.0 7575 1.0737.533.830.0 8080 1.0040.036.032.0 90900.8945.040.536.0 1001000.8050.045.040.0 1251250.6462.556.350.0 1501500.5375.067.560.0KF25x252513.525 4.0012.55011.34510.0403030 3.3315.013.512.0 3535 2.8617.515.814.0 4040 2.5020.018.016.0 4545 2.2222.520.318.0 5050 2.0025.022.520.0 5555 1.8227.524.822.0 6060 1.6730.027.024.0 6565 1.5432.529.326.0 7070 1.4335.031.528.0 7575 1.3337.533.830.08080 1.2540.036.032.0 9090 1.1145.040.536.0 100100 1.0050.045.040.0 1251250.8062.556.350.0 1501500.6775.067.560.0KF27x252713.525 4.8012.56011.35410.0483030 4.0015.013.512.0 3535 3.4317.515.814.0 4040 3.0020.018.016.0 4545 2.6722.520.318.0 5050 2.4025.022.520.0 5555 2.1827.524.822.0 6060 2.0030.027.024.0 6565 1.8532.529.326.0 7070 1.7135.031.528.0 7575 1.6037.533.830.0 8080 1.5040.036.032.0 9090 1.3345.040.536.0 100100 1.2050.045.040.0 1251250.9662.556.350.0 1501500.8075.067.560.0 1751750.6987.578.870.0KF30X25301625 5.7612.57211.36510.0583030 4.8015.013.512.0 3535 4.1117.515.814.0 4040 3.6020.018.016.0 4545 3.2022.520.318.0 5050 2.8825.022.520.0 5555 2.6227.524.322.06060 2.4030.027.024.0 6565 2.2232.529.326.0 7070 2.0635.031.528.0 7575 1.9237.533.830.0 8080 1.8040.036.032.0 9090 1.6045.040.536.0 100100 1.4450.045.040.0 125125 1.1562.556.350.0 1501500.9675.067.560.0 1751750.8287.578.870.0KF35x40351940 4.9020.09818.08816.0784545 4.3622.520.318.0 5050 3.9225.022.520.0 5555 3.5627.524.822.0 6060 3.2730.027.024.0 6565 3.0232.529.326.0 7070 2.8035.031.528.0 7575 2.6137.533.830.0 8080 2.4540.036.032.0 9090 2.1845.040.536.0 100100 1.9650.045.040.0 125125 1.5762.556.350.0 150150 1.3175.067.560.0 175175 1.1287.578.870.0 2002000.98100.090.080.0KF40x50402250 5.1225.012822.511520.01026060 4.2730.027.024.0 7070 3.6635.031.528.0 8080 3.2040.036.032.09090 2.8445.040.536.0 100100 2.5650.045.040.0 125125 2.0562.556.350.0 150150 1.7175.067.560.0 175175 1.4687.578.870.0 200200 1.28100.090.080.0 250250 1.02125.0112.5100.0KF50x605027.560 6.6730.020027.018024.01607070 5.7135.031.528.0 8080 5.0040.036.032.0 9090 4.4445.040.536.0 100100 4.0050.045.040.0 125125 3.2062.556.350.0 150150 2.6775.067.560.0 175175 2.2987.578.870.0 200200 2.00100.090.080.0 250250 1.60125.0112.5100.0 300300 1.33150.0135.0120.0KF60x90603390 6.4045.028840.525936.0230100100 5.7650.045.040.0 125125 4.6162.556.350.0 150150 3.8475.067.560.0 175175 3.2987.578.870.0 200200 2.88100.090.080.0 250250 2.30125.0112.5100.0 300300 1.92150.0135.0120.0模具弹簧规格表-KL轻荷重KL轻荷重LightLoad产品编号外径OuterDia.(mm)内径InnerDia.(mm)自由长FreeLength(mm)定数SpringConst.(kgf/mm)30万0.3million50万0.5million100万1million压缩量(mm)荷重(kgf)压缩量(mm)荷重(kgf)压缩量(mm)荷重(kgf)KL08x158415 1.67 6.0105.494.882020 1.258.07.2 6.4 2525 1.0010.09.08.0 30300.8312.010.89.6 35350.7114.012.611.2 40400.6216.014.412.8 45450.5618.016.214.4 50500.5020.018.016.0 55550.4522.019.817.6 60600.4224.021.619.2KL10x2010520 1.818.014.57.2136.411.42525 1.4510.09.08.03030 1.2112.010.89.63535 1.0414.012.611.240400.9116.014.412.845450.8118.016.214.450500.7220.018.016.055550.6622.019.817.660600.6024.021.619.2KL12x2012 6.520 2.628.0217.219 6.4172525 2.1010.09.08.0 3030 1.7512.010.89.6 3535 1.5014.012.611.2 4040 1.3116.014.412.8 4545 1.1718.016.214.4 5050 1.0520.018.016.0 55550.9522.019.817.6 60600.8824.021.619.2KL14x2514725 2.8010.0289.0258.0223030 2.3312.010.89.6 3535 2.0014.012.611.2 4040 1.7516.014.412.8 4545 1.5618.016.214.4 5050 1.4020.018.016.0 5555 1.2722.019.817.6 6060 1.1724.021.619.2 6565 1.0826.023.420.8 7070 1.0028.025.222.4KL16x2516825 3.5010.0359.0328.0283030 2.9212.010.89.6 3535 2.5014.012.611.2 4040 2.1916.014.412.8 4545 1.9418.016.214.4 5050 1.7520.018.016.0 5555 1.5922.019.817.6 6060 1.4624.021.619.2 6565 1.3526.023.420.8 7070 1.2528.025.222.4 7575 1.1730.027.024.08080 1.0932.028.825.6KL18x2518925 4.3010.0439.0398.0343030 3.5812.010.89.6 3535 3.0714.012.611.2 4040 2.6916.014.412.8 4545 2.3918.016.214.4 5050 2.1520.018.016.0 5555 1.9522.019.817.6 6060 1.7924.021.619.2 6565 1.6526.023.420.8 7070 1.5428.025.222.4 7575 1.4330.027.024.0 8080 1.3432.028.825.6 9090 1.1936.032.428.8KL20x25201025 5.4010.0549.0488.0433030 4.5012.010.89.6 3535 3.8614.012.611.2 4040 3.3816.014.412.8 4545 3.0018.016.214.4 5050 2.7020.018.016.0 5555 2.4522.019.817.6 6060 2.2524.021.619.2 6565 2.0826.023.420.8 7070 1.9328.025.222.4 7575 1.8030.027.024.0 8080 1.6932.028.825.6 9090 1.5036.032.428.8 100100 1.3540.036.032.0 125125 1.0850.045.040.0KL22x25221125 6.7010.0679.0608.0543030 5.5812.010.89.6 3535 4.7914.012.611.2 4040 4.1916.014.412.8 4545 3.7218.016.214.4 5050 3.3520.018.016.0 5555 3.0522.019.817.6 6060 2.7924.021.619.2 6565 2.5826.023.420.8 7070 2.3928.025.222.4 7575 2.2330.027.024.0 8080 2.0932.028.825.6 9090 1.8636.032.428.8 100100 1.6840.036.032.0 125125 1.3450.045.040.0 150150 1.1260.054.048.0KL25X252512.5258.4010.0849.0758.06730307.0012.010.89.6 3535 6.0014.012.611.2 4040 5.2516.014.412.8 4545 4.6718.016.214.4 5050 4.2020.018.016.0 5555 3.8222.019.817.6 6060 3.5024.021.619.2 6565 3.2326.023.420.8 7070 3.0028.025.222.4 7575 2.8030.027.024.0 8080 2.6232.028.825.6 9090 2.3336.032.428.8100100 2.1040.036.032.0 125125 1.6850.045.040.0 150150 1.4060.054.048.0KL27X252713.52510.0010.01009.0908.08030308.3312.010.89.6 35357.1414.012.611.2 4040 6.2516.014.412.8 4545 5.5618.016.214.4 5050 5.0020.018.016.0 5555 4.5522.019.817.6 6060 4.1724.021.619.2 6565 3.8526.023.420.8 7070 3.5728.025.222.4 7575 3.3330.027.024.0 8080 3.1232.028.825.6 9090 2.7836.032.428.8 100100 2.5040.036.032.0 125125 2.0050.045.040.0 150150 1.6760.054.048.0KL30x2530152512.1010.01219.01098.097303010.0812.010.89.6 35358.6414.012.611.2 40407.5616.014.412.8 4545 6.7218.016.214.4 5050 6.0520.018.016.0 5555 5.5022.019.817.6 6060 5.0424.021.619.2 6565 4.6526.023.420.8 7070 4.3228.025.222.47575 4.0330.027.024.0 8080 3.7832.028.825.6 9090 3.3636.032.428.8 100100 3.0240.036.032.0 125125 2.4250.045.040.0 150150 2.0260.054.048.0 175175 1.7370.063.056.0KL35x403517.54010.3116.016514.414912.813245459.1718.016.214.4 50508.2520.018.016.0 55557.5022.019.817.6 6060 6.8824.021.619.2 6565 6.3526.023.420.8 7070 5.8928.025.222.4 7575 5.5030.027.024.0 8080 5.1632.028.825.6 9090 4.5836.032.428.8 100100 4.1240.036.032.0 125125 3.3050.045.040.0 150150 2.7560.054.048.0 175175 2.3670.063.056.0 200200 2.0680.072.064.0KL40x5040205010.8020.021618.019416.017360609.0024.021.619.2 70707.7128.025.222.4 8080 6.7532.028.825.6 9090 6.0036.032.428.8 100100 5.4040.036.032.0 125125 4.3250.045.040.0150150 3.6060.054.048.0 175175 3.0970.063.056.0 200200 2.7080.072.064.0 250250 2.16100.090.080.0KL50x6050256014.0824.033821.630419.2270707012.0728.025.222.4 808010.5632.028.825.6 90909.3936.032.428.8 1001008.4540.036.032.0 125125 6.7650.045.040.0 150150 5.6360.054.048.0 175175 4.8370.063.056.0 200200 4.2280.072.064.0 250250 3.38100.090.080.0 300300 2.82120.0108.096.0KL60X9060309013.5036.048632.443728.838910010012.1540.036.032.0 1251259.7250.045.040.0 1501508.1060.054.048.0 175175 6.9470.063.056.0 200200 6.0880.072.064.0 250250 4.86100.090.080.0 300300 4.05120.0108.096.0模具弹簧规格表-KM中荷重KM中荷重MediumLoad产品编号外径OuterDia.(mm)内径InnerDia.(mm)自由长FreeLength(mm)定数SpringConst.(kgf/mm)30万0.3million30万0.3million100万1million压缩量(mm)荷重(kgf)压缩量(mm)荷重(kgf)压缩量(mm)荷重(kgf)KM08x158415 2.92 4.8144.312.53.8112020 2.19 6.4 5.8 5.1 2525 1.758.07.2 6.4 3030 1.469.68.77.7 3535 1.2511.210.19.0 4040 1.0912.811.010.2 45450.9714.413.011.5 50500.8816.014.412.8 55550.8017.615.914.1 60600.7319.217.315.4KM10x2010520 3.12 6.4205.8185.1162525 2.508.07.2 6.4 3030 2.089.68.77.7 3535 1.7911.210.19.0 4040 1.5612.811.510.2 4545 1.3914.413.011.5 5050 1.2516.014.412.8 5555 1.1417.615.914.1 6060 1.0419.217.315.4KM12x2012620 4.53 6.4295.8265.1232525 3.628.07.2 6.43030 3.029.68.77.7 3535 2.5911.210.19.0 4040 2.2712.811.610.2 4545 2.0114.413.011.5 5050 1.8116.014.412.8 5555 1.6517.615.814.1 6060 1.5119.217.315.4KM14x2514725 4.888.0397.2356.4313030 4.069.68.77.7 3535 3.4811.210.19.0 4040 3.0512.811.510.2 4545 2.7114.413.011.5 5050 2.4416.014.412.8 5555 2.2217.615.914.1 6060 2.0319.217.315.4 6565 1.8820.818.716.6 7070 1.7422.420.217.9KM16x2516825 6.388.0517.2466.4413030 5.319.68.67.7 3535 4.5511.210.19.0 4040 3.9812.811.510.2 4545 3.5414.413.011.5 5050 3.1916.014.412.8 5555 2.9017.615.914.1 6060 2.6619.217.315.4 6565 2.4520.818.716.6 7070 2.2822.420.217.9 7575 2.1224.021.619.2 8080 1.9925.623.020.5KM18x25189258.128.0657.2586.4523030 6.779.68.67.7 3535 5.8011.210.19.0 4040 5.0812.811.510.2 4545 4.5114.413.011.5 5050 4.0616.014.412.8 5555 3.6917.615.814.1 6060 3.3919.217.315.4 6565 3.1220.818.716.6 7070 2.9022.420.217.9 7575 2.7124.021.619.2 8080 2.5425.623.020.5 9090 2.2628.825.923.0KM20x2520102510.008.0807.2726.46430308.339.68.67.7 35357.1411.210.19.0 4040 6.2512.811.510.2 4545 5.5614.413.011.5 5050 5.0016.014.412.8 5555 4.5517.615.814.1 6060 4.1719.217.315.4 6565 3.8520.818.716.6 7070 3.5722.420.217.9 7575 3.3324.021.619.2 8080 3.1225.623.020.5 9090 2.7828.825.923.0 100100 2.5032.028.825.6KM22x2522112512.128.0977.2876.477303010.109.68.67.735358.6611.210.19.0 40407.5812.811.510.2 4545 6.7414.413.011.5 5050 6.0616.014.412.8 5555 5.5117.615.814.1 6060 5.0519.217.315.4 6565 4.6620.818.716.6 7070 4.3322.420.217.9 7575 4.0424.021.619.2 8080 3.7925.623.020.5 9090 3.3728.825.923.0 100100 3.0332.028.825.6 125125 2.4240.036.032.0KM25x252512.52515.628.01257.21126.4100303013.029.68.67.7353511.1611.210.19.040409.7712.811.510.245458.6814.413.011.550507.8116.014.412.855557.1017.615.814.16060 6.5119.217.315.46565 6.0120.818.716.67070 5.5822.420.217.97575 5.2124.021.619.28080 4.8825.623.020.59090 4.3428.825.923.0100100 3.9132.028.825.6125125 3.1240.036.032.0KM27x252713.52518.258.01467.2131 6.4117303015.219.68.67.7 353513.0411.210.19.0 404011.4112.811.510.2 454510.1414.413.011.5 50509.1216.014.412.8 55558.3017.615.814.1 60607.6019.217.315.4 65657.0220.818.716.6 7070 6.5222.420.217.9 7575 6.0824.021.619.2 8080 5.7025.623.020.5 9090 5.0728.825.323.0 100100 4.5632.028.825.6 125125 3.6540.036.032.0 150150 3.0448.043.238.4KM30x2530152522.508.01807.21616.4144303018.759.68.67.7 353516.0711.210.19.0 404014.0612.811.510.2 454512.5014.413.011.5 505011.2516.014.412.8 555510.2317.615.814.1 60609.3819.217.315.4 65658.6520.818.716.6 70708.0422.420.217.9 75757.5024.021.619.2 80807.0325.623.020.5 9090 6.2528.825.923.0 100100 5.6232.028.825.6125125 4.5040.036.032.0 150150 3.7548.043.238.4 175175 3.2156.050.444.8KM35x403517.54019.1412.824511.522010.2195454517.0114.413.011.5 505015.3116.014.412.8 555513.9217.615.814.1 606012.7619.217.315.4 656511.7820.818.716.6 707010.9422.420.217.9 757510.2124.021.619.2 80809.5725.623.020.5 90908.5128.825.923.0 1001007.6632.028.825.6 125125 6.1240.036.032.0 150150 5.1048.043.238.4 175175 4.3856.050.444.8 200200 3.8364.057.651.2KM40x5040205020.0016.032014.428812.8256606016.6719.217.315.4 707014.2922.420.217.9 808012.5025.623.020.5 909011.1128.825.923.0 10010010.003228.825.6 1251258.0040.036.032.0 150150 6.6748.043.238.4 175175 5.7156.050.444.8 200200 5.0064.057.651.2 250250 4.0080.072.064.0KM50x6050256026.0419.250017.345015.4400707022.3222.420.217.9 808019.5325.623.020.5 909017.3628.825.923.0 10010015.6232.028.825.6 12512512.5040.036.032.0 15015010.4248.043.238.4 1751758.9356.050.444.8 2002007.8164.057.651.2 250250 6.2580.072.064.0 300300 5.2196.086.476.8KM60x7060307032.1422.472020.264817.9575808028.1225.623.020.5 909025.0028.825.923.0 10010022.5032.028.825.6 12512518.0040.036.032.0 15015015.0048.043.238.4 17517512.8656.050.444.8 20020011.2564.057.651.2 2502509.0080.072.064.0 3003007.5096.086.476.8模具弹簧规格表-KH重荷重KH重荷重HeavyLoad产品编号外径OuterDia.(mm)内径InnerDia.(mm)自由长FreeLength(mm)定数SpringConst.(kgf/mm)30万0.3million50万0.5million100万1million压缩量(mm)荷重(kgf)压缩量(mm)荷重(kgf)压缩量(mm)荷重(kgf)KH08x158415 5.83 3.6213.2192.9172020 4.38 4.8 4.3 3.8 2525 3.50 6.0 5.4 4.8 3030 2.927.2 6.5 5.8 3535 2.508.47.6 6.7 4040 2.199.68.67.7 4545 1.9410.89.78.6 5050 1.7512.010.89.6 5555 1.5913.211.910.6 6060 1.4614.413.011.5KH10x2010520 6.25 4.8304.3273.8242525 5.00 6.0 5.4 4.83030 4.177.2 6.5 5.83535 3.578.47.6 6.74040 3.129.68.67.74545 2.7810.89.78.65050 2.5012.010.810.05555 2.2713.211.910.66060 2.0814.413.011.5KH12x20126208.96 4.843 4.338 3.83425257.17 6.0 5.4 4.8 3030 5.977.2 6.5 5.8 3535 5.128.47.6 6.7 4040 4.489.68.67.7 4545 3.9810.89.78.6 5050 3.5812.010.810.0 5555 3.2613.211.910.6 6060 2.9914.413.011.5KH14x25147259.83 6.0595.4534.84730308.197.2 6.5 5.8 35357.028.47.6 6.7 4040 6.159.68.67.7 4545 5.4610.89.78.6 5050 4.9212.010.810.0 5555 4.4713.211.910.6 6060 4.1014.413.011.5 6565 3.7815.614.012.5 7070 3.5116.815.113.4KH16x251682512.83 6.0775.4694.862303010.697.2 6.5 5.8 35359.178.47.6 6.7 40408.029.68.67.7 45457.1310.89.78.6 5050 6.4212.010.89.6 5555 5.8313.211.910.6 6060 5.3514.413.011.5 6565 4.9415.614.012.5 7070 4.5816.815.113.4 7575 4.2818.016.214.48080 4.0119.217.315.4KH18x251892516.17 6.0975.4874.878303013.477.2 6.5 5.8 353511.558.47.6 6.7 404010.109.68.67.7 45458.9810.89.78.6 50508.0812.010.89.6 55557.3513.211.910.6 6060 6.7414.413.011.5 6565 6.2215.614.012.5 7070 5.7716.815.113.4 7575 5.3918.016.214.4 8080 5.0519.217.315.4 9090 4.4921.619.417.3KH20x2520102520.00 6.01205.41084.896303016.677.2 6.5 5.8353514.298.47.6 6.7404012.509.68.67.7454511.1110.89.78.6505010.0012.010.89.655559.0913.211.910.660608.3314.413.011.565657.6915.614.012.570707.1416.815.113.47575 6.6718.016.214.48080 6.2519.217.315.49090 5.5621.619.417.3100100 5.0024.021.619.2KH22x25222524.17 6.0145 5.4130 4.8116303020.147.2 6.5 5.8 353517.268.47.6 6.7 404015.109.68.67.7 454513.4310.89.78.6 505012.0812.010.89.6 555510.9813.211.910.6 606010.0714.413.011.5 65659.2915.614.012.5 70708.6316.815.113.4 75758.0618.016.214.4 80807.5519.217.315.4 9090 6.7121.619.417.3 100100 6.0424.021.619.2 125125 4.8330.027.024.0KH25x252512.52531.17 6.01875.41694.8150303025.977.2 6.5 5.8 353522.268.47.6 6.7 404019.489.68.67.7 454517.3110.89.78.6 505015.581210.89.6 555514.1713.211.910.6 606012.9914.413.011.5 656511.9915.614.012.5 707011.1316.815.113.4 757510.3918.016.214.4 80809.7419.217.315.4 90908.6621.619.417.3 1001007.7924.021.619.2 125125 6.2330.027.024.0KH27x252713.52536.50 6.02195.41974.8175303030.427.2 6.5 5.8 353526.078.47.6 6.7 404022.819.68.67.7 454520.2810.89.78.6 505018.2512.010.89.6 555516.5913.211.910.6 606015.2114.413.011.5 656514.0415.614.012.5 707013.0416.815.113.4 757512.1718.016.214.4 808011.4119.217.315.4 909010.1421.619.417.3 1001009.1224.021.619.2 1251257.3030.027.024.0 150150 6.0836.032.428.8KH30x2530152545.00 6.02705.42434.8216303037.507.2 6.5 5.8 353532.148.47.6 6.7 404028.129.68.67.7 454525.0010.89.78.6 505022.5012.010.89.6 555520.4513.211.910.6 606018.7514.413.011.5 656517.3115.614.012.5 707016.0716.815.113.4 757515.0018.016.214.4 808014.0619.217.315.4 909012.5021.619.417.310010011.2524.021.619.2 1251259.0030.027.024.0 1501507.5036.032.428.8 175175 6.4342.037.833.6KH35x403517.54038.239.63678.63307.7293454533.9810.89.78.6 505030.5812.010.89.6 555527.8013.211.910.6 606025.4914.413.011.5 656523.5315.614.012.5 707021.8516.815.113.4 757520.3918.016.214.4 808019.1119.217.315.4 909016.9921.619.417.3 10010015.2924.021.619.2 12512512.2330.027.024.0 15015010.1936.032.428.8 1751758.7442.037.833.6 2002007.6548.043.238.4KH40x5040205040.0012.048010.84329.6384606033.3314.413.011.5 707028.5716.815.113.4 808025.0019.217.315.4 909022.2221.619.417.3 10010020.0024.021.619.2 12512516.0030.027.024.0 15015013.3336.032.428.8 17517511.4342.037.833.6 20020010.0048.043.238.42502508.0060.054.048.0KH50x6050256052.0814.475013.067511.5600707044.6416.815.113.4 808039.0619.217.315.4 909034.7221.619.417.3 10010031.2524.021.619.2 12512525.0030.027.024.0 15015020.8336.032.428.8 17517517.8642.037.833.6 20020015.6248.043.238.4 25025012.5060.054.048.0 30030010.4272.064.857.6KH60x7060307064.2916.8108015.197313.4864808056.2519.217.315.4 909050.0021.619.417.3 10010045.0024.021.619.2 12512536.0030.027.024.0 15015030.0036.032.428.8 17517525.7142.037.833.6 20020022.5048.043.238.4 25025018.0060.054.048.0 30030015.0072.064.857.6模具弹簧规格表-KB超重荷重KB极重荷重SUPERLoad产品编号外径OuterDia.(mm)内径InnerDia.(mm)自由长FreeLength(mm)定数SpringConst.(kgf/mm)30万0.3million50万0.5million100万1million压缩量(mm)荷重(kgf)压缩量(mm)荷重(kgf)压缩量(mm)荷重(kgf)KB08x15841511.30 3.0352.730.52.42620208.47 4.0 3.6 3.2 2525 6.78 5.0 4.5 4.0 3030 5.65 6.0 5.4 4.8 3535 4.847.0 6.3 5.6 4040 4.248.07.2 6.4 4545 3.779.08.17.2 5050 3.3910.09.08.0 5555 3.0811.09.98.8 6060 2.8212.010.89.6KB10x201052011.25 4.0453.6413.23625259.00 5.0 4.5 4.030307.50 6.0 5.4 4.83535 6.437.0 6.3 5.64040 5.628.07.2 6.44545 5.009.08.17.25050 4.5010.09.08.05555 4.0911.09.98.86060 3.7512.010.89.6KB12x201262014.50 4.058 3.652 3.246252511.60 5.0 4.5 4.0 30309.67 6.0 5.4 4.8 35358.297.0 6.3 5.6 40407.258.07.2 6.4 4545 6.449.08.17.2 5050 5.8010.09.08.0 5555 5.2711.09.98.8 6060 4.8312.010.89.6KB14x251472515.00 5.0754.5684.060303012.50 6.0 5.4 4.8 353510.717.0 6.3 5.6 40409.388.07.2 6.4 45458.339.08.17.2 50507.5010.09.08.0 5555 6.8211.09.98.8 6060 6.2512.010.89.6 6565 5.7713.011.710.4 7070 5.3614.012.611.2KB16x251682520.00 5.01004.5904.080303016.67 6.0 5.4 4.8 353514.297.0 6.3 5.6 404012.508.07.2 6.4 454511.119.08.17.2 505010.0010.09.08.0 55559.0911.09.98.8 60608.3312.010.89.6 65657.6913.011.710.4 70707.1414.012.611.2 7575 6.6715.013.512.08080 6.2516.014.412.8KB18x251892525.00 5.01254.51134.0100303020.83 6.0 5.4 4.8 353517.867.0 6.3 5.6 404015.628.07.2 6.4 454513.899.08.17.2 505012.5010.09.08.0 555511.3611.09.98.8 606010.4212.010.89.6 65659.6213.011.710.4 70708.9314.012.611.2 75758.3315.013.512.0 80807.8116.014.412.8 9090 6.9418.016.214.4KB20x2520102532.00 5.01604.51444.0128303026.67 6.0 5.4 4.8353522.867.0 6.3 5.6404020.008.07.2 6.4454517.789.08.17.2505016.0010.09.08.0555514.5511.09.98.8606013.3312.010.89.6656512.3113.011.710.4707011.4314.012.611.2757510.6715.013.512.0808010.0016.014.412.890908.8918.016.214.41001008.0020.018.016.0KB22x25222539.00 5.0195 4.5176 4.0156303032.50 6.0 5.4 4.8 353527.867.0 6.3 5.6 404024.388.07.2 6.4 454521.679.08.17.2 505019.5010.09.08.0 555517.7311.09.98.8 606016.2512.010.89.6 656515.0013.011.710.4 707013.9314.012.611.2 757513.0015.013.512.0 808012.1916.014.412.8 909010.8318.016.214.4 1001009.7520.018.016.0 1251257.8025.022.520.0KB25x252512.52549.00 5.02454.52214.0196303040.83 6.0 5.4 4.8 353535.007.0 6.3 5.6 404030.628.07.2 6.4 454527.229.08.17.2 505024.5010.09.08.0 555522.2711.09.98.8 606020.4212.010.89.6 656518.8513.011.710.4 707017.5014.012.611.2 757516.3315.013.512.0 808015.3116.014.412.8 909013.6118.016.214.4 10010012.2520.018.016.0 1251259.8025.022.520.0KB27X252713.52558.00 5.02904.52614.0232303048.33 6.0 5.4 4.8 353541.437.0 6.3 5.6 404036.258.07.2 6.4 454532.229.08.17.2 505029.0010.09.08.0 555526.3611.09.98.8 606024.1712.010.89.6 656522.3113.011.710.4 707020.7114.012.611.2 757519.3315.013.512.0 808018.1216.014.412.8 909016.1118.016.214.4 10010014.5020.018.016.0 12512511.6025.022.520.0 1501509.6730.027.024.0KB30x2530152572.00 5.03604.53244.0288303060.00 6.0 5.4 4.8 353551.437.0 6.3 5.6 404045.008.07.2 6.4 454540.009.08.17.2 505036.0010.09.08.0 555532.7311.09.98.8 606030.0012.010.89.6 656527.6913.011.710.4 707025.7114.012.611.2 757524.0015.013.512.0 808022.5016.014.412.8909020.0018.016.214.4 10010018.0020.018.016.0 12512514.4025.022.520.0 15015012.0030.027.024.0 17517510.2935.031.528.0KB35x403517.54061.258.04907.24416.4392454554.449.08.17.2 505049.0010.09.08.0 555544.5511.09.98.8 606040.8312.010.89.6 656537.6913.011.710.4 707035.0014.012.611.2 757532.6715.013.512.0 808030.6216.014.412.8 909027.2218.016.214.4 10010024.5020.018.16.0 12512519.6025.022.520.0 15015016.3330.027.024.0 17517514.0035.031.528.0 20020012.2540.036.032.0 KB40X540205064.0010.06409.05768.0512606053.3312.010.89.6 707045.7114.012.611.2 808040.0016.014.412.8 909035.5618.016.214.4 10010032.0020.018.016.0 12512525.6025.022.520.0 15015021.3330.027.024.017517518.2935.031.528.0 20020016.0040.036.032.0 25025012.8050.045.040.0KB50x6050256083.3312.0100010.89009.6800707071.4314.012.611.2 808062.5016.014.412.8 909055.5618.016.214.4 10010050.0020.018.016.0 12512540.0025.022.520.0 15015033.3330.027.024.0 17517528.5735.031.528.0 20020025.0040.036.032.0 25025020.0050.045.040.0 30030016.6760.054.048.0KB60x9060309080.0018.0144016.2129614.4115210010072.0020.018.016.0 12512557.6025.022.520.0 15015048.0030.027.024.0 17517541.1435.031.528.0 20020036.0040.036.032.0 25025028.8050.045.040.0 30030024.0060.054.048.0。
模具弹簧规格及参数
模具弹簧规格及参数模具弹簧规格及参数⼀. 弹簧功能弹簧是模具中⼴泛应⽤的弹性零件,主要⽤于卸料、压料、推件和顶出等⼯作.根据荷重不同,共分五种不同颜⾊加以区分,易於判别和选⽤.⼆. 规格系列1.弹簧外径系列: Φ6Φ8,Φ10,Φ12,Φ14,Φ16,Φ18,Φ20,Φ22,Φ25,Φ30,Φ35,Φ40,Φ50等.2.种类3.弹簧长度：15<=L<=80MM时,每5MM为⼀个阶;80=L>=100MM时,每25MM为⼀个阶.4.扁线弹簧最⼩直径6mm5.弹簧内径等于弹簧外径的⼆分之⼀.6.相同直径颜⾊的弹簧，不管⾃由长度是多长，压40％产⽣的⼒⼀样结论：相同直径颜⾊的弹簧，⾃由长度越短，压缩1mm产⽣的⼒越⼤7.通常使⽤的最⼤压缩⽐是弹簧使⽤30万次的最⼤压缩⽐.汽车模具使⽤50万次的最⼤压缩⽐..8.弹簧能压缩的长度=弹簧的⾃由长度x弹簧的压缩⽐例：Φ20绿⾊弹簧长度50mm，弹簧要求寿命30万次，弹簧能压缩多长？50x24％=12(mm)9.弹簧的长度=弹簧要压缩的长度÷弹簧的压缩⽐例：弹簧要压缩20mm, 弹簧颜⾊为红⾊，弹簧要求寿命50万次要⽤多长的弹簧？弹簧的长度=20÷28.8％+5MM=74.4 查表选⽤75MM长弹簧⼀般选弹簧长度会加5mm的安全余量10.弹簧要压缩的长度=活动板⾏程+3~5mm预压 (常规预压3mm)11.弹簧模板孔的⼤⼩直径<20模板孔=D+1直径>=20模板孔=D+2三. 选⽤原则1.长度选择⼀般保证:在开模状态弹簧的预压缩量等於3~5(常规预压3mm,预压缩量随实际情况⽽定.);闭模状态弹簧压缩量⼩於或等於最⼤压缩量(最⼤压缩量LA=弹簧⾃由长L*最⼤压缩⽐取值%).2.模板压料，脱料板压料优先选⽤绿⾊或棕⾊（茶⾊，咖啡⾊)弹簧;如果向上成形的下模压料，折弯脱料所需的顶料⼒不很⼤时,可选⽤红⾊,绿⾊弹簧，浮料⽤黄⾊，圆线弹簧.3.复合模外脱料板⽤红⾊弹簧,内脱料板⽤绿⾊或棕⾊弹簧.4.活动定位销⼀般选⽤Φ6顶料销,配Φ10黄⾊弹簧和M12⽌付螺丝.Φ8顶料销,配Φ12黄⾊弹簧和M14⽌付螺丝.5.冲孔模和成形模⽤绿⾊或棕⾊（茶⾊，咖啡⾊)弹簧,如有特殊需求时,由专案主管确定.6.弹簧规格优先选⽤Φ30.在空间较⼩区域可考虑选⽤其它规格(如Φ25,Φ20,Φ18,Φ16…...等).Φ25的内导柱⽤Φ30的弹簧脱料Φ20的内导柱⽤Φ25的弹簧脱料四. 排配原则1.弹簧过孔中⼼到模板边缘距离⼤於外径D,与其他孔距离保持实体壁厚⼤於5MM,空间不⾜时最少留2MM.2.弹簧排列⾸先考虑受⼒重点部位,然後再考虑整个模具受⼒均衡平稳.受⼒重点部位是指:复合模的内脱料板外形和冲头的周围;冲孔模的冲头周围;成形模的折弯边及有抽成形的地⽅.3.成形模采⽤⽓垫结构时,下打板排配2~6个弹簧.下模座上不沉孔,弹簧选⽤黄⾊或蓝⾊即可.五. 五⾦零件需求表填写范例弹簧(颜⾊):D*L (D-弹簧外径L-⾃由长度)例: 弹簧TH(绿): Φ20*70。
模具弹簧规格及参数
模具弹簧规格及参数一.弹簧功能弹簧是模具中广泛应用的弹性零件,主要用于卸料、压料、推件和顶出等工作.根据荷重不同,共分五种不同颜色加以区分,易於判别和选用.二.规格系列1.弹簧外径系列: Φ6Φ8,Φ10,Φ12,Φ14,Φ16,Φ18,Φ20,Φ22,Φ25,Φ30,Φ35,Φ40,Φ50等.2.种类3.弹簧长度：15<=L<=80MM时,每5MM为一个阶;80=<L<=100MM时,每10MM为一个阶;L>=100MM时,每25MM为一个阶.4.扁线弹簧最小直径6mm5.弹簧内径等于弹簧外径的二分之一.6.相同直径颜色的弹簧，不管自由长度是多长，压40％产生的力一样结论：相同直径颜色的弹簧，自由长度越短，压缩1mm产生的力越大7.通常使用的最大压缩比是弹簧使用30万次的最大压缩比.汽车模具使用50万次的最大压缩比..8.弹簧能压缩的长度=弹簧的自由长度x弹簧的压缩比例：Φ20绿色弹簧长度50mm，弹簧要求寿命30万次，弹簧能压缩多长？50x24％=12(mm)9.弹簧的长度=弹簧要压缩的长度÷弹簧的压缩比例：弹簧要压缩20mm, 弹簧颜色为红色，弹簧要求寿命50万次要用多长的弹簧？弹簧的长度=20÷28.8％+5MM=74.4 查表选用75MM长弹簧一般选弹簧长度会加5mm的安全余量10.弹簧要压缩的长度=活动板行程+3~5mm预压(常规预压3mm)11.弹簧模板孔的大小直径<20模板孔=D+1直径>=20模板孔=D+2三.选用原则1.长度选择一般保证:在开模状态弹簧的预压缩量等於3~5(常规预压3mm,预压缩量随实际情况而定.);闭模状态弹簧压缩量小於或等於最大压缩量(最大压缩量LA=弹簧自由长L*最大压缩比取值%).2.模板压料，脱料板压料优先选用绿色或棕色（茶色，咖啡色)弹簧;如果向上成形的下模压料，折弯脱料所需的顶料力不很大时,可选用红色,绿色弹簧，浮料用黄色，圆线弹簧.3.复合模外脱料板用红色弹簧,内脱料板用绿色或棕色弹簧.4.活动定位销一般选用Φ6顶料销,配Φ10黄色弹簧和M12止付螺丝.Φ8顶料销,配Φ12黄色弹簧和M14止付螺丝.5.冲孔模和成形模用绿色或棕色（茶色，咖啡色)弹簧,如有特殊需求时,由专案主管确定.6.弹簧规格优先选用Φ30.在空间较小区域可考虑选用其它规格(如Φ25,Φ20,Φ18,Φ16…...等).Φ25的内导柱用Φ30的弹簧脱料Φ20的内导柱用Φ25的弹簧脱料四.排配原则1.弹簧过孔中心到模板边缘距离大於外径D,与其他孔距离保持实体壁厚大於5MM,空间不足时最少留2MM.2.弹簧排列首先考虑受力重点部位,然後再考虑整个模具受力均衡平稳.受力重点部位是指:复合模的内脱料板外形和冲头的周围;冲孔模的冲头周围;成形模的折弯边及有抽成形的地方.3.成形模采用气垫结构时,下打板排配2~6个弹簧.下模座上不沉孔,弹簧选用黄色或蓝色即可.五.五金零件需求表填写范例弹簧(颜色):D*L (D-弹簧外径L-自由长度)例: 弹簧TH(绿): Φ20*70。
模具弹簧规格及参数
模具弹簧规格及参数一. 弹簧功能弹簧是模具中广泛应用的弹性零件,主要用于卸料、压料、推件和顶出等工作.根据荷重不同,共分五种不同颜色加以区分,易於判别和选用.二. 规格系列1.弹簧外径系列:Φ6Φ8,Φ10,Φ12,Φ14,Φ16,Φ18,Φ20,Φ22,Φ25,Φ30,Φ35,Φ40,Φ50等.2.种类3.弹簧长度：15<=L<=80MM时,每5MM为一个阶;80=<L<=100MM时,每10MM为一个阶;L>=100MM时,每25MM为一个阶.4.扁线弹簧最小直径6mm5.弹簧内径等于弹簧外径的二分之一.6.相同直径颜色的弹簧，不管自由长度是多长，压40％产生的力一样结论：相同直径颜色的弹簧，自由长度越短，压缩1mm产生的力越大7.通常使用的最大压缩比是弹簧使用30万次的最大压缩比.汽车模具使用50万次的最大压缩比..8.弹簧能压缩的长度=弹簧的自由长度x弹簧的压缩比例：Φ20绿色弹簧长度50mm，弹簧要求寿命30万次，弹簧能压缩多长？50x24％=12(mm)9.弹簧的长度=弹簧要压缩的长度÷弹簧的压缩比例：弹簧要压缩20mm, 弹簧颜色为红色，弹簧要求寿命50万次要用多长的弹簧？弹簧的长度=20÷28.8％+5MM=74.4 查表选用75MM长弹簧一般选弹簧长度会加5mm的安全余量10.弹簧要压缩的长度=活动板行程+3~5mm预压 (常规预压3mm)11.弹簧模板孔的大小直径<20模板孔=D+1直径>=20模板孔=D+2三. 选用原则1.长度选择一般保证:在开模状态弹簧的预压缩量等於3~5(常规预压3mm,预压缩量随实际情况而定.);闭模状态弹簧压缩量小於或等於最大压缩量(最大压缩量LA=弹簧自由长L*最大压缩比取值%).2.模板压料，脱料板压料优先选用绿色或棕色（茶色，咖啡色)弹簧;如果向上成形的下模压料，折弯脱料所需的顶料力不很大时,可选用红色,绿色弹簧，浮料用黄色，圆线弹簧.3.复合模外脱料板用红色弹簧,内脱料板用绿色或棕色弹簧.4.活动定位销一般选用Φ6顶料销,配Φ10黄色弹簧和M12止付螺丝.Φ8顶料销,配Φ12黄色弹簧和M14止付螺丝.5.冲孔模和成形模用绿色或棕色（茶色，咖啡色)弹簧,如有特殊需求时,由专案主管确定.6.弹簧规格优先选用Φ30.在空间较小区域可考虑选用其它规格(如Φ25,Φ20,Φ18,Φ16…...等).Φ25的内导柱用Φ30的弹簧脱料Φ20的内导柱用Φ25的弹簧脱料四. 排配原则1.弹簧过孔中心到模板边缘距离大於外径D,与其他孔距离保持实体壁厚大於5MM,空间不足时最少留2MM.2.弹簧排列首先考虑受力重点部位,然後再考虑整个模具受力均衡平稳.受力重点部位是指:复合模的内脱料板外形和冲头的周围;冲孔模的冲头周围;成形模的折弯边及有抽成形的地方.3.成形模采用气垫结构时,下打板排配2~6个弹簧.下模座上不沉孔,弹簧选用黄色或蓝色即可.五. 五金零件需求表填写范例弹簧(颜色):D*L (D-弹簧外径L-自由长度)例: 弹簧TH(绿): Φ20*70。